BIS - LIMS (Laboratory Information Management System)

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY, HEHAL, RANCHI, JHARKHAND

HEHAL, RANCHI, JHARKHAND, INDIA, Ranchi, Ranchi, Jharkhand, 834005

9325687905 cipetranchi@gmail.com

Scope List

Reset

23 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 18482 (2023)

Textiles - Sandwich extrusion laminated polypropylene PP woven sacks for packaging bulk commodities - Specification

TYPE- I, II, III, IV, V, VI & VII

30951.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Sack Type)	-	0	-
5.2.1(Fabric)	-	0	For Tape Testing as per IS 6192:2023 charges will be applicable as per IS 6192
5.2.2(Linear density of tapes)	-	700	-
5.2.4(Unlaminated fabric mass)	-	500	Plus GST as applicable
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	500	Plus GST as applicable
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	500	Plus GST as applicable
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	500	Plus GST as applicable
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	500	Plus GST as applicable
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	500	Plus GST as applicable
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	500	Plus GST as applicable
5.4.1(Sack)	-	500	For Visual Appearance Plus GST as applicable
5.4.1.1(Centre seam)	-	500	For Visual Appearance Plus GST as applicable
5.4.1.2(Bottom seam)	-	0	-
5.4.2(Sack)	-	0	-
5.4.3(Sack)	-	500	-
5.4.5(Liner)	-	3000.00	for Identification: 2000/- Visual: 500/- Dimensions of Liner: 500/-
6.1.1, Table 1(Inside length)	-	500	including length width & gussets
6.1.1, Table 1(Inside width)	-	0	-
6.1.1, Table 1(Gusset width)	-	0	-
6.1.1, Table 1(Warp per dm)	-	500	Including Warp per dm & Weft per dm
6.1.1, Table 1(Weft per dm)	-	0	-
6.1.1, Table 1(Mass of laminated fabric)	-	500	-
6.2, Table 1(Average breaking strength - Lengthwise)	-	1600	1100/- for test & 500/- for Specimen Preparation
6.2, Table 1(Average breaking strength - Widthwise)	-	1600	1100/- for test & 500/- for Specimen Preparation
6.2, Table 1(Breaking strength of bottom seam)	-	1600	1100/- for test & 500/- for Specimen Preparation
6.2, Table 1(Breaking strength of centre seam)	-	1600	1100/- for test & 500/- for Specimen Preparation
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	0	-
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	0	-
6.3(Average breaking strength - Lengthwise after UV exposure)	-	10180	For UV Resistance : 10180/- 1100/- for test & 500/- for Specimen Preparation Total: 11,780.00
6.3(Average breaking strength - Widthwise after UV exposure)	-	1600	1100/- for test & 500/- for Specimen Preparation
6.4(Drop Impact Testing of Filled Sacks)	-	1100	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 6.5 Table 1 viii(Ash content)	-	1200	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 13.02.2025

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

TYPE- I & II

18993.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	-
4.1(Raw Material)	-	1050	Material Identification
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	-
4.2(Tapes – Linear Density )	-	700	For complete tape testing, IS 6192:2023 charges will be taken.
4.2(Construction)	-	0	-
4.3(Sacks)	-	500	For Visual Inspection
4.3.1(Bottom Seam)	-	500	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4(Liner IS 10146 or IS 10910.)	-	1050	Material Identification
4.4(Mass of the loose liner )	-	500	For GSM
4.4(Width of the loose liner)	-	500	500.00 for liner Visual, Length, width & Thickness
4.4(Length of the line)	-	0	-
4.4(Bottom seam of the loose liner)	-	0	-
4.4.1(Liner)	-	0	-
4.5 and Table 1 i(Capacity)	-	500	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	for all kind of sack dimensions
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	Rs. 10180.00 for UV Resistance 1100.00 for Lengthwise strength 1100.00 for widthwise strength
5.2 and Table 1 x(Ash content )	-	1200	-
3(TYPES)	-	0	-
4.1(Raw Material)	-	0	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4(Liner IS 10146 or IS 10910.)	-	0	-
4.4(Mass of the loose liner )	-	0	-
4.4(Width of the loose liner)	-	0	-
4.4(Length of the line)	-	0	-
4.4(Bottom seam of the loose liner)	-	0	-
4.4.1(Liner)	-	0	-
4.5 and Table 1 i(Capacity)	-	0	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	0	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	0	-
5.2 and Table 1 iv(Picks per dm )	-	0	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	0	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	0	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	0	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
5.2 and Table 1 x(Ash content )	-	0	-
4.2 (Mesh size and weight in g/cm2) (amendment 3)(Mesh size and weight in g/cm2)	-	0	-
5.3(UV Resistance)	-	0	-
Cl-4.4 (Amendment-3)(Thickness of liner)	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 13.02.2025

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

Category- A & B

9544.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	6900.00	For Raw Material Identification: 1050/- Toluene Extract: 1100/- Volatile Content: 700/- Density: 700 + 625 /- MFI: 1100/- CBC: 925/- CBD: 700/-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	0	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	0	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	700	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	1100	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	700	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	925	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	-
6.2.2(Fittings)	-	0	-
6.3(General)	-	500	For Visual Appearance
6.3(General)	-	0	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	250	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	250	-
8.3.3(Flow Paths in Emitting Unit)	-	250	-
8.3.4(Spacing ofEmitter Units)	-	250	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1600	-
8.5(Resistance to Tension at Elevated Temperature)	-	1100	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	500	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1200	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1600	-
8.8(Determination of Emitting Unit Exponent)	-	600	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	-
4.1 a(Identification)	-	1050	-
4.1 a(Identification)	-	0	-
4.1 c(Volatile matter Extract)	-	700	-
4.1 d(Density)	-	700	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	1100	-
4.2(Carbon black content)	-	925	-
4.2(Carbon black dispersion)	-	700	-
5.1(Materials)	-	0	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	250	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	250	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	0	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	250	-
6.2(Fittings)	-	0	-
6.3(General)	-	500	-
7.1(Test Specimens)	-	0	-
7.2(Order of Tests)	-	0	-
7.3(Testing Conditions)	-	0	-
7.4(Accuracy of Measuring Devices)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.2(Unregulated Emitting Pipes)	-	0	-
8.1.3(Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregulated Emitting Pipes)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing of Emitter Units)	-	0	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	0	-
8.7.1(Acceptance Test)	-	0	-
8.7.2(Type Test)	-	0	-
8.8(Determination of Emitting Unit Exponen)	-	0	-
9.1(Non-regulated Emitting Pipe)	-	0	-
9.2(Regulated Emitting Pipe)	-	0	-
10.1(Marking)	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included.w.e.f.30.01.2025

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

Category - A & B

3825.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Construction and workmanship)	-	500	+ GST as applicable Total Test Charges = Rs. 5100/- (25 % Discount on Test Charges for BIS)
7.2(Flow path in emitters)	-	500	+ GST as applicable
7.3.1(Resistance to Hydrostatic pressure)	-	1000	+ GST as applicable
7.3.2(Resistance to Hydrostatic pressure)	-	0	-
7.3.3(Resistance to Hydrostatic pressure)	-	0	-
7.4.1(Emitter Pull Out In-line emitters)	-	500	+ GST as applicable
7.4.2(Emitter Pull Out On-line emitters)	-	0	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	1000	+ GST as applicable
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	0	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	-
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	1000	+ GST as applicable
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	0	-
8.3(Determination of Emitter Exponent)	-	600	+ GST as applicable
4(Classification)	-	0	-
5.1(Connections)	-	0	-
5.2(Emitter Ends)	-	0	-
5.3(Materials)	-	0	-
6.1(Test Specimens)	-	0	-
6.2(Test Conditions)	-	0	-
6.3(Accuracy or Measuring Devices)	-	0	-
7.1(Construction and Workmanship)	-	0	-
7.2(Flow Paths In Emitter)	-	0	-
7.3(Resistance to Hydrostatic Pressure)	-	0	-
7.4(Emitter Pull-out)	-	0	-
7.4.1(In-Line Emitters)	-	0	-
7.4.2(On-Line Emitters)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.1(Number of Test Samples)	-	0	-
8.1.2(Unregulated Emitters)	-	0	-
8.1.3(Regulated Emitters)	-	0	-
8.2(Emission Rate as a Function of Inlet Pressure)	-	0	-
8.2.1(Selection of Telt Sample)	-	0	-
8.2.2(Unregulated Emttters)	-	0	-
8.2.3(Regulated Emitters)	-	0	-
8.3(Determiaatlon of Emitter Exponent)	-	0	-
9(Marking)	-	0	-
7.1(Construction and workmanship)	-	0	-
7.2(Flow path in emitters)	-	0	-
7.3.1(Resistance to Hydrostatic pressure)	-	0	-
7.3.2(Resistance to Hydrostatic pressure)	-	0	-
7.3.3(Resistance to Hydrostatic pressure)	-	0	-
7.4.1(Emitter Pull Out In-line emitters)	-	0	-
7.4.2(Emitter Pull Out On-line emitters)	-	0	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	0	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	0	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	-
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	0	-
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	0	-
8.3(Determination of Emitter Exponent)	-	0	-
4(Classification)	-	0	-
5.1(Connections)	-	0	-
5.2(Emitter Ends)	-	0	-
5.3(Materials)	-	0	-
6.1(Test Specimens)	-	0	-
6.2(Test Conditions)	-	0	-
6.3(Accuracy or Measuring Devices)	-	0	-
7.1(Construction and Workmanship)	-	0	-
7.2(Flow Paths In Emitter)	-	0	-
7.3(Resistance to Hydrostatic Pressure)	-	0	-
7.4(Emitter Pull-out)	-	0	-
7.4.1(In-Line Emitters)	-	0	-
7.4.2(On-Line Emitters)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.1(Number of Test Samples)	-	0	-
8.1.2(Unregulated Emitters)	-	0	-
8.1.3(Regulated Emitters)	-	0	-
8.2(Emission Rate as a Function of Inlet Pressure)	-	0	-
8.2.1(Selection of Telt Sample)	-	0	-
8.2.2(Unregulated Emttters)	-	0	-
8.2.3(Regulated Emitters)	-	0	-
8.3(Determiaatlon of Emitter Exponent)	-	0	-
9(Marking)	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included.w.e.f.30.01.2025

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

11200.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	3775.00	Identification: 1050/- CBC: 925/- Toluene Extract: 1100/- Volatile Matter: 700/- Additional GST as applicable
Cl-4.2(Carbon content of finished PE lateral pipe)	-	925.00	Additional GST as applicable
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	500	Additional GST as applicable
Cl-6.0(Visual Appearance)	-	500	Additional GST as applicable
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	1000.00	Additional GST as applicable
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	3000.00	Additional GST as applicable
Cl-7.2(Reversion Test)	-	1200	700/- test charges + 500/- sample preparation
Cl-7.3(Tensile Test)	-	1800.00	1300/- test charges + 500/- sample preparation
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1200.00	-
Cl-8.0(Supply of pipes)	-	0	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	925.00	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	700.00	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 20.01.2025

IS 6192 (2023)

Textiles Monoaxially oriented high density polyethylene HDPE and polypropylene PP tapes Specification

HDPE & PP Tape

18630.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(High Density Polyethylene Tapes)	-	4300.00	Density: 700/- plus 500/- (Specimen preparation) MFI: 1100/- Identification: 2000/- GST as Applicable & 25 % Discount on test charges only for BIS
Cl-4.2(Polypropylene Tapes)	-	4300.00	Density: 700/- plus 500/- (Specimen preparation) MFI: 1100/- Identification: 2000/- GST as Applicable & 25 % Discount on test charges only for BIS
Cl-4.3(Additives and Masterbatches)	-	0	-
Cl-5.1.1(Finished tape width)	-	500	-
Cl-5.1.2(Thickness of the tape)	-	500	-
Cl-5.1.3(Linear density of tape)	-	700	-
Cl-5.1.4(Polypropylene Tapes)	-	1100	1100/- for Tenacity, Elongation at break & Strength
Cl-5.1.5(Average value of the elongation at break of tape)	-	0	-
Cl-5.1.6(UV radiation exposure)	-	10180.00	For 192 hrs. UV Conditioning
Cl-5.1.6(UV stabilized HDPE and PP resins)	-	1100	for tenacity after UV
Cl-5.1.7(Average heat shrinkage of HDPE tapes)	-	1700.00	-
Cl-5.1.8(Ash Content)	-	1200.00	-
Cl-6.1(Marking)	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 20.01.2025

IS 12100 (1987)

Specification for high density polyethylene (HDPE) woven sacks for packing flour

TYPE-1 & TYPE-2

12013.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1, Table 1(Breaking strength of fabric on 5 × 20 cm strip, Widthwise)	-	1600	1100/- FOR TEST & 500/- FOR SAMPLE PREPARATION
3.1, Table 1(Breaking strength of fabric on 5 × 20 cm strip, Lengthwise)	-	1600	1100/- FOR TEST & 500/- FOR SAMPLE PREPARATION
3.1, Table 1(Seam breaking strength, Side team)	-	1600	1100/- FOR TEST & 500/- FOR SAMPLE PREPARATION
3.1, Table 1(Seam breaking strength, Bottom team)	-	1600	1100/- FOR TEST & 500/- FOR SAMPLE PREPARATION 2.3.1 Liner Identification of liner: 1050 Length & width of liner: 500 GSM & Visual:500
3.2(Dimensions)	-	500	Cl. no. 2.1 Fabric a) Identification: 1050 b) width of tape: 500 c) Linear Density: 700 2.2 Sack Visual: 500 2.3 Lamination: Identification: 1050 Thickness/GSM: 500
3.3(Mass)	-	500	cl no 2.4: Seam Dimension: 500 Identification of Stitching: 1050 Breaking load:1100 Stitching tape denier: 700 2.5 Mouth of sack: 500 2.6 Capacity: 500

Complete

10 Aug, 2023

09 Aug, 2026

-
Included.w.e.f.15.01.2025

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

PP OR HDPE BAGS

18853.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	1050	for Identification
3.2(Tapes – Width )	-	500	-
3.2(Tapes – Linear Density )	-	700	-
3.3(Tying Cord)	-	500	includes: No. of strand Dia of Rope length of rope
3.3(Tying Cord)	-	1050	for identification of strand rope
3.3(Tying Cord)	-	0	-
3.4(Sack)	-	500	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	2500	Includes: UV presence on thread: 2000/- Dimensions of stitching: 500/-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	500	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	500	-
4.1 and Table 1 ii(Ends per dm )	-	500	-
4.1 and Table 1 iii(Picks per dm )	-	500	-
4.2 and Table 1 iv(Mass of sack )	-	500	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	1100	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	1100	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12540	2200/- for Breaking Strength 10340/- for UV conditioning
4.1 and Table 1 ix(Ash content )	-	1200	-
3.1(Raw Material)	-	0	-
3.2(Tapes – Width )	-	0	-
3.2(Tapes – Linear Density )	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.3(Tying Cord)	-	0	-
3.4(Sack)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
3.4.1(Seam)	-	0	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	0	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	0	-
4.1 and Table 1 ii(Ends per dm )	-	0	-
4.1 and Table 1 iii(Picks per dm )	-	0	-
4.2 and Table 1 iv(Mass of sack )	-	0	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	0	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	0	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	0	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.1 and Table 1 ix(Ash content )	-	0	-
3.2 (Mesh size and weight is g/cm2) (amendment 3)(Mesh size and weight is g/cm2)	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 11-09-2024.

IS 16709 (2017)

Textiles - Polypropylene (PP) woven, laminated, block bottom valve sacks for packaging of 50 kg cement - Specification

BLOCK BOTTOM VALVE SACKS

18238.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Sack Length)	-	2000	including: sack length sack width Closure width, top & bottom Patch length & Height (top closure) Patch length & Height (Bottom closure) valve length valve sleeve width valve sleeve length
4.1.2(Sack Width)	-	0	-
4.1.3(Top Closure Width and Bottom Closure Width)	-	0	-
4.1.4(Patch Length)	-	0	-
4.1.5(Patch Height)	-	0	-
4.1.6(Length of Valve)	-	0	-
4.1.7(Width of Valve Sleeve)	-	0	-
4.1.8(Length of Valve Sleeve)	-	0	-
5.1(Raw Material)	-	1050.00	Identification
5.2(Fabric)	-	6150.00	Amount 6150/- includes Fabric construction: 500 Identification: 1050 MFI: 1100 Tenacity: 1100 thickness: 500 Width: 500 Dimensional stability: 1400
5.2(Tape density and width)	-	1200	-
5.4(Lamination for PP)	-	2550	Amount 2550/- includes: mass of lamination: 500 total mass: 500 Identification: 1050 overhang width: 500
5.4(Lamination for LDPE)	-	0	Test charges for cl no.: 5.3 (5.3) Sack Construction: 500 (5.3.1) Construction of Top & Bottom closure: 500 Filling valve: 500
6.1(Mass of Bale)	-	500	-
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	2700	Amount 2700/- includes: Warp Direction: 1100 Weft: 1100 sample preparation: 500
6.2.2(Weld Strength of Top and Bottom Closures)	-	1100	-
6.3(Drop Impact Testing of Filled Sacks)	-	1100	-
6.4(Ash Content)	-	1200	-
6.5(Air Permeability)	-	1100	-
8(Atomspheric Conditions for Conditioning and Testing)	-	0	-
Cl-5.6(Capacity)	-	500	-
Cl- 6.6, Table.-1 (ii)(Ends per dm)	-	500	-
Cl-6.6, Table-1 (iii)(Picks per dm)	-	500	-
Cl.6.6, Table-1 (vii)(Elongation at break of fabric)	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 09.09.2024 Exclusion: Cl.6.5 (Air Permeability)

IS 17399 (2020)

Textiles - Polypropylene ( PP )/ High Density Polyethylene ( HDPE ) Laminated Woven Sacks for Mail Sorting, Storage, Transport and Distribution - Specification

TYPE-I, TYPE-II & TYPE-III

34505.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE - Raw Materials)	-	1050	MATERIAL IDENTIFICATION
5.2(MANUFACTURE - Fabric for PP tapes & for HDPE tapes)	-	7850	AMOUNT 7,850/- INCLUDE Fabric Construction: 500 Tape width: 500 Identification: 1050 MFI: 1100 Linear Density: 700 Tanacity: 1100 Thickness: 500 Dimensional stability: 1400 gsm: 500
5.3(Lamination)	-	2050	2050/- includes Mass of lamination film: 500 Total mass: 500 Identification of Lamination: 1050
5.4(Sack Fabrication)	-	1500	1500/- includes: Sacks Dimension:500 Gromet Construction & Dimension: 1000 Clause no: 5.4.1 Stitching: 500 No of stitching per dm: 1100 bottom seam construction: 500 thread identification: 1050 Break load: 1100 Presence of UV: 2000
5.5(Capacity)	-	500	-
6.1- Table 1- i)(REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm)	-	1500	includes all dimension as per table-1
6.1- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	500	-
6.1- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	500	-
5.2- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	500	-
5.2- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf) a) Lengthwise b) Widthwise)	-	2700	2700/- includes: Warp Direction: Strength : 1100/- Weft Direction: Strength 1100/- sample preparation: 500/-
5.2- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min, N2), (kgf))	-	1100	-
6.1- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	1200	-
5.2- Table 1- i)("REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm")	-	0	-
5.2- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	0	-
5.2- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	0	-
5.2- Table 1- vii)("REQUIREMENTS - Elongation at break of fabric, percent: a) Lengthwise b) Widthwise")	-	2200	Warp & Weft Includes
5.2- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	0	-
6.1- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	0	-
6.1- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf))	-	0	-
6.1- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min)	-	0	-
6.1- Table 1- vii)(REQUIREMENTS - Elongation at break of fabric, percent a) Lengthwise b) Widthwise)	-	0	-
6.4(UV Resistance Test)	-	12880	192 hrs UV Conditioning: 10180/- Warp Direction: 1100/- Weft Direction: 1100/- Sample preparation: 500/-
7(PRINTING, PACKAGING AND MARKING)	-	0	-
8(ATMOSPHERIC CONDITIONS FOR SAMPLE CONDITIONING AND TESTING)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 5.4(Sack Fabrication)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 09.09.2024

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

25 KG POLYMER BAG

20555 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Linear Density)	-	700	For Fabric tape: (Extra charges) Material Identification: 1050/- Melt Flow Index: 1100/- Mesh Size:500/- Tenacity: 1100/- Density (Raw Material): 700/-
4.2(Width of tape)	-	500	Clause No: 4.2 Thickness of tape: 500/- Heat Shrinkage: 1700/- Dimensional Stability: 700/- (Each condition) GSM: 500 Clause No: 4.1 (Optional) Raw Material Identification: 1050/-
4.3(Sacks)	-	500	Visual
4.3.1(Bottom Seam)	-	500	Outer Stitching: 500/- Depth of seam over double fold: 500/- No of Stitches per dm: 500/- Identification of Stitching material: 1050/- Breaking load of thread: 1100/- (500/- for sample preparation) Presence of UV in Thread, 2000/-
4.6(Capacity)	-	500	Extra charges as per Standard Clause no: 4.4 (For Lamination) Identification of Lamination: 2000/- GSM: 500/- Lamination overhang: 500/- For Clause no: 4.5 Identification of Liner: 2000/- Dimensions of Liner: 500/- Visual of Liner: 500/-
5.2 Table 1(Dimensions)	-	500	Including Length, Width & Width of the gusset
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Ends per dm)	-	500	-
5.2 Table 1(Picks per dm)	-	500	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	500	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	2700	2200/- Including Warp + Weft Direction (Avg. Breaking Strength + Elongation at break) and 500/- for Specimen preparation
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	0	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1100	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	-
5.2 Table 1(Drop impact strength)	-	1600	500 for sample preparation/Conditioning
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	1200	Ash Content
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	0	-
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	2700	2200/- Including Warp + Weft Direction (Avg. Breaking Strength ) and 500/- for Specimen preparation
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	10180	-
5.1(Mass of Bale)	-	0	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Dimensions)	-	0	-
4.2(Linear Density)	-	0	-
4.2(Width of tape)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.6(Capacity)	-	0	-
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	0	-
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	0	-

Complete

10 Aug, 2023

09 Aug, 2026

-
Included w.e.f. 09.09.2024

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

PE63, PE80 & PE100, Up to DN 315 mm

36881 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1125	TEST (500/-) SAMPLE PREPARATION (625/-)
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2200	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	700	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	700	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	1125	OPTIONAL TEST (500/-) SAMPLE PREPARATION (625/-)
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	925	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	700	OPTIONAL
5.2.1.1, T2(Compound ash content - Any Method)	-	950	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	700	OPTIONAL
6.2(Colour- IS 14333-2022)	-	250	VISUAL
7.1(Visual Appearance- IS 14333-2022)	-	300	VISUAL
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	500	INCLUDES: OD WALLTHICKNESS OVALITY
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	4000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	4800	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	11000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	900	TEST (700/-) SAMPLE PREPARATION (200/-)
8.3(Carbon black content- IS 2530-1963)	-	925	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	700	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1100	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2200	-
8.6(Density-IS 7328:2020)	-	500	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1600	TEST (1100/-) SAMPLE PREPARATION (500/-)
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1600	TEST (1100/-) SAMPLE PREPARATION (500/-)
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	6000	TEST (5500/-) SAMPLE PREPARATION (500/-)
7.2(Length- IS 14333-2022)	-	300	-
7.3(Coiling- IS 14333-2022)	-	300	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

TYPE-I, II, III, IV & V

17155 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	IDENTIFICATION
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	-
4.2(Tapes – Linear Density )	-	500	OPTIONAL
4.3(Sacks)	-	300	VISUAL INCLUDES VISUAL OF BOTTOM SEAM
4.3.1(Bottom Seam)	-	0	-
4.3.1(The number of stitches/dm)	-	500	OPTIONAL
4.3.2(Mouth)	-	300	VISUAL (OPTIONAL)
4.4 and Table 1 i(Capacity)	-	250	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	INCLUDE LENGTH & WIDTH
5.2 and Table 1 iii(Ends per dm )	-	250	-
5.2 and Table 1 iv(Picks per dm )	-	250	-
5.1 and Table 1 v(Mass of sack )	-	250	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	INCLUDES : AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	INCLUDES : AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	INCLUDES : AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	INCLUDES : AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	INCLUDES: UV RESISTANCE WEATHERING (192 Hrs.) , 10180/-( DISCOUNT NOT APPLICABLE) AVERAGE BREAKING STRENGTH- LENGTHWISE (1100/-) WIDTH WISE (1100/-)
5.2 and Table 1 x(Ash content )	-	950	-
5.2 and Table 1 x(Ash content )	-	0	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

GUSSETED TYPE & NON-GUSSETED TYPE

23605 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material )	-	1050	IDENTIFICATION
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	250	-
4.2 (Fabric)	-	1050	IDENTIFICATION
4.2 (Linear Density, 900 denier)	-	500	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	250	-
4.4(Seam )	-	300	VISUAL
4.4(Seam)	-	1050	IDENTIFICATION
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	500	LINEAR DENSITY
4.4(The number of stitches/dm shall be 14 ± 2.)	-	250	-
4.5(Lamination )	-	1050	IDENTIFICATION
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	400	-
4.7(Valve for Filling of Sacks)	-	250	VISUAL
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	500	INCLUDES: LENGTH WIDTH WIDTH OF GUSSETS WIDTH OF VALVE DEPTH OF GUSSETS
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	250	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	250	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	500	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	500	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100	INCLUDES: AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100	INCLUDES: AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	500	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	950	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	950	-
5/5.6 (UV Resistance, )	-	10180	UV RESISTANCE WEATHERING (192 Hrs.) CHARGES
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	1100	AVERAGE BREAKING STRENGTH
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	1100	AVERAGE BREAKING STRENGTH
4.3(Sacks)	-	250	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

HDPE/PP WOVEN SACKS

17080 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material Identification)	-	1050	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250	-
3.3.1(Bottom seam (IS 10789))	-	250	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	250	-
4.2 and Table 1 ii(Dimensions )	-	250	INCLUDES: LENGTH & WIDTH
5.2 and Table 1 iii(Ends per dm )	-	200	-
5.2 and Table 1 iv(Picks per dm )	-	200	-
4.2 and Table 1 v(Mass of sack )	-	300	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	INCULUDES: AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK LENGTH WISE (1100/-) WIDTH WISE (1100/-)
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	INCULUDES: AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK LENGTH WISE (1100/-) WIDTH WISE (1100/-)
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	INCULUDES: AVERAGE BREAKING STRENGTH & ELONGATION AT BREAK LENGTH WISE (1100/-) WIDTH WISE (1100/-) UV RESISTANCE WEATHERING: (10180/-)
4.2 and Table 1 x(Ash content )	-	950	Additional Charges
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	900	Additional Charges
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	1100	Additional Charges Includes: tenacity & Elongation of the tape
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	Additional Charges
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	850	Additional Charges
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	700	Additional Charges
3.2(Unlaminated Fabric Mass )	-	300	Additional Charges

Complete

10 Aug, 2023

09 Aug, 2026

-
Exclusion: Cl.3.2 (Colour Fastness for pigmented tapes)

IS 9755 (2021)

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

TYPE-I & II

21692 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Meterial)	-	1050	IDENTIFICATION (OPTIONAL)
4.2("Fabric b) Linear Density")	-	500	-
4.2("Fabric c) Mesh")	-	500	-
4.2("Fabric d) Unlaminated Fabric Mass")	-	250	-
4.3(Sacks)	-	300	VISUAL
4.4.1(Loose Liner)	-	250	-
4.4.1(Thickness of Linear)	-	250	-
4.4.2(Visual Observation)	-	300	-
4.4.3(Bottom Seam of Loose Liner)	-	300	-
4.5(Mass of The Lamination)	-	250	-
4.5(Laminated Fabric)	-	300	-
4.6.1(Distance between the Two Row of Stitches)	-	300	-
4.7(Mouth of the Sack)	-	300	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	250	INCLUDES LENGTH & WIDTH
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	250	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	250	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	3300	AVERAGE BREAKING STRENGTH & ELONGATION OF FABRIC IN LENGTH WISE (1100/-) WIDTH WISE (1100/-) WIDTH WISE (LAMINATED JOINTS) (1100/-)
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	1100	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	AVERAGE BREAKING STRENGTH & ELONGATION OF FABRIC IN LENGTH WISE (1100/-) WIDTH WISE (1100/-)
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	AVERAGE BREAKING STRENGTH & ELONGATION OF FABRIC IN LENGTH WISE (1100/-) WIDTH WISE (1100/-)
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	950	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content b) For Non- UV Stabilized Sack")	-	950	-
"Table 1 of Cl. No.5.6 Sl. No. x"(Drop Impact Strength)	-	500	-
Cl. No.5.7(UV Resistance)	-	12380	INCLUDES: UV RESISTANCE WEATHERING (10180/-) AVERAGE BREAKING STRENGTH IN LENGTH WISE (1100/-) WIDTH WISE (1100/-)
Cl. No.5.2(Visual Observation)	-	250	Tape Visual: 250/- Linear Density: 500/- Tanacity & Elongation of the Tape: 1100/- Width of the Tape: 250/- Thickness of tape: 200/- Heat Shrinkage (@ 60°C & 95°C): 850/-
4.6.1(Depth of the Stitch( Double fold))	-	250	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 11584 (1986)

Specification for high density polyethylene (Hdpe) crates for milk satchets

HDPE CRATES FOR MILK SATCHETS

7838 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Material Identification)	-	1050	-
2.2(Material )	-	1600	CL. NO.: 2.2- DENSITY & MELT FLOW INDEX (500 + 1100)
2.3(Shape and Dimensions)	-	500	-
2.4(Mass )	-	300	-
2.5(Appearance and Surface Finish)	-	300	-
2.7(Resistance to Stress)	-	1000	-
2.8(Resistance to Applied Load)	-	1000	-
2.9(Strength)	-	3400	CL. NO: 2.9.1 RESISTANCE TO DROP (1100/-) 2.9.2 RESISTANCE TO LOW TEMP. DROP (1100/- + 1200/-) TOTAL= 3400/-
2.1(Dimensional Stability)	-	900	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 11805 (2007)

Polyethylene pouches for packaging liquid milk - Specification - (Second Revision)

FULL RANGE

7050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Visual)	-	250	VISUAL+FILM FORM+ WINDING OF FILM+ ODOUR (ALL INCLUDE 250/-)
5.2(Film form)	-	0	-
5.3(winding)	-	0	-
5.4(Odour)	-	0	-
5.5(Thickness)	-	250	-
5.6(Width)	-	250	-
5.7(Tensile Strength)	-	2200	TENSILE STRENGTH + ELONGATION AT BREAK =1100 (1100+1100) IN BOTH DIRECTION
5.8(Elongation at Break)	-	0	TENSILE STRENGTH + ELONGATION AT BREAK =1100 (1100+1100) IN BOTH DIRECTION
5.9(Dart Impact Resistance)	-	850	-
5.10(Slip (Coefficient of Friction))	-	850	-
8.1(Leak Test)	-	400	-
8.2(Drop Test)	-	1100	-
8.3(Ink adhesion test)	-	500	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 10889 (2004)

High density polyethylene films (First Revision)

GRADE-1 & 2

8800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials)	-	2225	DENSITY & MFI
5.2(Black Compound)	-	1625	CARBON BLACK CONTENT & CARBON BLACK DISPERSION
6.1.1(Appearance)	-	300	INCLUDES: APPEARANCE, FILM & ODOUR
6.1.2(Film Form)	-	0	-
6.1.3(Odour )	-	0	-
6.1.4(Density)	-	500	-
6.1.5(Melt Flow Rate)	-	1100	-
6.1.6(Black Film)	-	1625	CARBON BLACK CONTENT & CARBON BLACK DISPERSION
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	250	-
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	250	-
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	600	-
6.4.1(Tensile Strength at Break)	-	1100	-
6.4.2(Elongation at Break)	-	1100	-
6.4.3(Impact Resistance (Falling Dart))	-	850	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

DIA UPTO 32

12612 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.a (Potyethylene - higher olefins constituent )	-	1050	-
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	-
4.1.c.ii (Toluene extract - Annex A)	-	1100	-
4.1.c.iii (Volatile matter - Annex B )	-	700	-
4.1.c.i (Density)	-	1125	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	150	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	100	-
6.1(Visual Appearance)	-	300	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	1000	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	3000	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Test)	-	675	-
7.3(Elongation at Break)	-	675	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

VERTICAL & LOFT TANK FULL RANGE

13850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.1(Density)	-	500	-
4.2.2(MFI)	-	1100	-
4.2.3(Carbon Black Content )	-	925	-
4.2.3(Carbon Dispersion Test)	-	700	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	1800	Dimensions as per Cl. No: 5.1, 5.2, 5.3 & 5.4 (Cylindrical & Loft) Includes: Capacity: 500/- Overall Dia/Length/Width: 250/-Each Overall Height: 250/- ID of Man-hole: 250/- Min Weight without lid: 500/- Visual: 300/-
5.4(Wall Thickness)	-	250	Wall Thickness Above Effective Height (250/-) Wall Thickness Below Effective Height (250/-) Wall Thickness of outer layer of Tank (250/-)
6.1(Finish)	-	300	Visual
7.1.1(Resistance to Deformation)	-	700	-
7.2(Resistance to Impact)	-	1100	-
7.3(Test for Top Load Resistance)	-	900	-
7.4(Tensile Strength)	-	1350	For Tensile Strength: 1100/- Specimen Preparation: 250/-
7.5(Flexural Modulus)	-	1600	For Flexural Strength: 1100/- Specimen Preparation: 500/-
7.6(overall Migration)	-	2200	For Overall Migration : 1700/- Specimen Preparation/Conditioning: 500/-
9.1(Man-Hole and Hand-Hole Lids)	-	2975.00	ForMaterial Identification: 1050/- Visual: 300/- Carbon Black Content: 925/- Carbon Black Dispersion: 700/-
9.2(Man-Hole and Hand-Hole Lids)	-	200	For Lid Lock Up (Visual)
9.2.1(Man-Hole and Hand-Hole Lids)	-	200	For Lid Clearance
5.2 Table 2 (7)(Minimum Wall Thickness)	-	250	For Wall Thickness in Tank
9.1(Lid Thickness)	-	250	For Lid Thickness

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

PE63, PE80 & PE100 DN UPTO 315MM

41625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Density)	-	1125	For Density: 500/- Specimen preparation: 625/-
5.2(MFI @ 1900C/5.0 Kg)	-	1100	-
5.2(Volatile matter Content)	-	700	-
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	2200	-
6.2.1(6.1.1 Identification Stripes)	-	250	-
6.2(Colour)	-	250	Visual
7.4 table -3 & 4(6.1 Dimensions)	-	500	Dimension Includes: Mean Outside Dia ovality Wall Thickness
7.4.1.2(Ovality)	-	0	-
Clause 7.1(Visual Apperance)	-	300	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	Hydraulic Characteristics: 100 hrs/27°C (4000/-) 48 hrs/80°C (1600/-) 165 hrs/80°C (4800/-) 1000 hrs/80°C (11000/-)
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	48 hrs/80°C (1600/-) for Joint Pipe
8.2(Longitudinal Reversion Test)	-	900	For Reversion: 700/- Specimen preparation: 200/-
Clause 8.3(Carbon Black content)	-	925	-
Clause 8.3(Carbon Black Dispersion)	-	700	-
8.4( Melt Flow Rate)	-	1100	-
8.5 (Oxidation Induction Time)	-	2200	-
8.6(Overall migration)	-	2000	For Overall Migration : 1700/- Specimen preparation: 300/-
8.7(Density)	-	500	-
8.8(Tensile Strength for Butt-fusion)	-	1600	For Tensile test : 1100/- Specimen preparation: 500/-
8.9 table-6(Elongation at Break)	-	1600	For Tensile at yield & Elongation test : 1100/- Specimen preparation: 500/-
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.10(Slow Crack Growth Rate)	-	6000	For Slow Crack growth test : 5500/- Specimen preparation: 500/- For 500hrs./80°C
7.2(Length)	-	300	-
7.3(Coiling)	-	300	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

TYPE-I, II, III & IV

14606 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	300	Includes" Appearance. Film Form, Odour
5.1.2(Film Form)	-	0	-
5.1.3(Odour)	-	0	-
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	500	-
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	-
5.1.6a(Carbon Black Content, Annex-A)	-	925	Carbon black content (optional) In Black Film
5.1.6b(Ash Content, Annex-A)	-	950	In Black Film
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	In Black Film
5.2.2(Tolerance on Thickness, Annex-A)	-	250	-
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1350	FOR TABLE 1, 2 & 3 For Tensile & Elongation: 1100/- Specimen Preparation: 250/-
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1350	FOR TABLE 1 , 2 & 3 For Tensile & Elongation: 1100/- Specimen Preparation: 250/-
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4300	-
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1000	-
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1000	IN Case of Type-IV Film Tear Test Charges will be: 1500/- Specimen Preparation: 500/- (Each)
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1000	IN Case of Type-IV Film Tear Test Charges will be: 1500/- Specimen Preparation: 500/- (Each)
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1350	FOR TABLE 1 , 2 & 3 For Tensile & Elongation: 1100/- Specimen Preparation: 250/-
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1350	FOR TABLE 1 , 2 & 3 For Tensile & Elongation: 1100/- Specimen Preparation: 250/-
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	2700	FOR TABLE 1 , 2 & 3 For Tensile & Elongation: 1100/- Specimen Preparation: 250/-
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	2700	FOR TABLE 1 , 2 & 3 For Tensile & Elongation: 1100/- Specimen Preparation: 250/-
9.1, Table 4(Puncture resistance , Annex C)	-	1350	For Puncture test: 1100/- Specimen Preparation: 250/-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1350	For Tensile : 1100/- Specimen Preparation: 250/-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1350	For Tensile : 1100/- Specimen Preparation: 250/-
Clause 5.2.3(Tolerance on Width)	-	250	-
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	2700	AS PER TABLE: 04 CL. NO:9.1 For Break Strenth & Break Elongation : 2200/- (WD) Specimen Preparation: 500/-
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	2700	AS PER TABLE: 04 CL. NO:9.1 For Break Strenth & Break Elongation : 2200/- (WD) Specimen Preparation: 500/-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	AS PER TABLE: 04 CL. NO:9.1 For Break Strenth & Break Elongation : 2200/- (WD) Specimen Preparation: 500/-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	AS PER TABLE: 04 CL. NO:9.1 For Break Strenth & Break Elongation : 2200/- (WD) Specimen Preparation: 500/-
5.2.1.1(Nominal Thickness)	-	250	-
5.2.1.2(Nominal width)	-	250	-

Complete

10 Aug, 2023

09 Aug, 2026

-
-

Bureau of Indian Standards

The National Standards Body of India

CENTRAL INSTITUTE OF PETROCHEMICALS ENGINEERING & TECHNOLOGY, HEHAL, RANCHI, JHARKHAND

HEHAL, RANCHI, JHARKHAND, INDIA, Ranchi, Ranchi, Jharkhand, 834005

9325687905 cipetranchi@gmail.com

Scope List