BIS - LIMS (Laboratory Information Management System)

ALPHA TEST HOUSE PRIVATE LIMITED

198-199, M.I.E, PHASE-I, BAHADURGARH, HARYANA-124507, Bahadurgarh, Jhajjar, Haryana, 124507

9711227171 info@alphatesthouse.com

Scope List

Reset

209 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 13893 (1994)

Polyurethane soles semirigid - specification

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3.2(Ageing test)	-	674	-
4.3(Ross Flex test)	-	666	-
4.3(Abrasion Resistance)	-	666	-
4.3(Elongation at break)	-	666	-
4.3(Tensile Strength )	-	666	-
4.3(Hardness Shore(A))	-	666	-
4.3(Relative density )	-	666	-
4.2(Thickness )	-	666	-
4.1(Design)	-	666	-
5, 5.1, 5.2(Packing And Marking)	-	666	-
Cl.5, 5.1, 5.2(Packing And Marking)	-	666	-
4.2 (Amendment 2)(Thickness)	-	0	-
4.3.1 Table 1 i) (Amendment 2)(Relative Density)	-	0	-
4.3.1 Table 1 iii) (Amendment 2)(Abrasion Resistance at applied force of 10 N)	-	0	-
4.3.1 Table 1 iv) (Amendment 2)(Flexing Resistance, Bennewart method)	-	0	-
4.3.1 Table 1 v) (Amendment 2)(Hydrolysis Resistance, cut growth after 150000 flexes)	-	0	-
4.3.1 Table 1 vi) (Amendment 2)(Tensile Strength)	-	0	-
4.3.1 Table 1 vii) (Amendment 2)(Elongation at break)	-	0	-
4.3.1 Table 1 viii) (Amendment 2)(Tear Strength (average force))	-	0	-

Complete

26 Aug, 2024

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	360	-
5/5.1(REQUIREMENTS-General)	-	360	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	360	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	360	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	360	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	360	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	360	-
5/5.1(REQUIREMENTS-General)	-	360	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	360	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	360	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	360	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	360	-
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	360	-
5/5.1(REQUIREMENTS-General)	-	360	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	360	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	360	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	360	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	360	-
6(Marking and packing)	-	360	-
8.1(Test methods)	-	360	-
8.3(Measurement of thickness)	-	360	-
Cl.6.1,6.2,6.3(Marking and packing)	-	360	-
8.1(Test Methods)	-	360	-
Cl.8.3(Measurement of thickness ")	-	360	-
5.5 (Amendment 1)(Thickness)	-	0	-
5.7 Table 2 i) (Amendment 1)(Relative Density)	-	0	-
5.7, Table 2 ii) (Amendment 1)(Hardness, degree, Shore A)	-	0	-
5.7, Table 2 iv) (Amendment 1)(Abrasion Resistance at applied force of 10 N)	-	0	-
5.7, Table 2 v) (Amendment 1)(Tensile strength)	-	0	-
5.7, Table 2 vi) (Amendment 1)(Elongation at break)	-	0	-
5.7, Table 2 vii) (Amendment 1)(Tear strength (average force))	-	0	-
5.7, Table 2 iii) (Amendment 1)(Flexing resistance)	-	0	-

Complete

26 Aug, 2024

IS 5405 (2019)

Sanitary napkins – Specification (second revision)

36850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(SIZES, Regular )	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 5(SIZES, Large)	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 5(SIZES, Extra Large)	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 5(SIZES, XXL)	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	350	GST@18% extra
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	1000	GST@18% extra
Cl 5(Absorbent Capacity, Regular )	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 5(Absorbent Capacity, Large)	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 5(Absorbent Capacity, Extra Large)	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 5(Absorbent Capacity, XXL)	-	1500	Rs. 1500 will be charged for applicable size of sample received. GST@18% extra
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	6000	GST@18% extra
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	6000	GST@18% extra
Cl 5(SIZES, Regular )	-	0	-
Cl 5(SIZES, Large)	-	0	-
Cl 5(SIZES, Extra Large)	-	0	-
Cl 5(SIZES, XXL)	-	0	-
Cl 5(Absorbent Capacity, Regular )	-	0	-
Cl 5(Absorbent Capacity, Large)	-	0	-
Cl 5(Absorbent Capacity, Extra Large)	-	0	-
Cl 5(Absorbent Capacity, XXL)	-	0	-
Cl 7.1(pH Value, IS 1390 (cold method) for all sizes)	-	0	-
Cl 7.2(Ability to Withstand Pressure after Absorption, for all sizes, Annex B)	-	0	-
Cl 7.3.1(Bacterial and Fungal Bioburden, 7.3.1.1, ISO 11737 (Part 1))	-	0	-
Cl7.3.2(Test for Common Skin Pathogen — Staphylococcus Aureus, 7.3.2.1, IS 5887 (Part 2))	-	0	-
Cl 7.4(Biocompatibility Evaluation — Cytotoxicity, Irritation and Skin Sensitization, IS/ISO 10993 Part 5 and IS/ISO 10993 Part 10)	-	0	-
Cl 7.5(Biodegradability and Compostability (Optional), IS/ISO 17088.)	-	0	-
3.1(Cover/Top sheet)	-	0	-
3.2(Absorbent Core)	-	0	-
3.3(Barrier or Bottom Sheet)	-	0	-
4.1 (1)(Type and shapes of sanitary napkins)	-	0	-
4.2(Sanitary napkins shape & design)	-	0	-
6.0(Manufacture, workmanship & finish)	-	0	-
CL 7.4(Biocompatibility Evaluation - Cytotoxicity, Irritation and Skin Sensitization (Optional))	-	0	-
CL 7.5(Compostability or Biodegradability during Composting (Optional))	-	0	-
7.6(Pthalate test)	-	0	-

Complete

26 Aug, 2024

IS 17265 (2023)

Textiles 100 Percent Polyester Spun Grey and White Yarns Specification Second Revision

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.No. 4(CLASSIFICATIONS)	-	0	-
Cl.No. 5.1, Table no. 1("Designation of Yarn ")	-	2500	-
Cl.No.5.2 , Table no. 2(IDENTIFICATION AND DESCRIPTION)	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 3(i)(Mean linear density (Count))	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 3(ii)(Twist per metre,)	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 3(iii)(Average Single yarn tenacity)	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 3(iv)(Elongation)	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 3(v)(Average Count strength product (CSP))	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 3(vi)(Yarn hairiness index)	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 3(vii)(Whiteness index of polyester spun yarn)	-	2500	-
Cl.No. 6.1,6.2 Table no. 4(i)(Moisture regain)	-	2500	-
Cl.No. 6.1,6.2 Table no. 4(ii)(Isophthalic Acid (IPA) content)	-	2500	-
Cl.No. 6.1,6.2 Table no. 4(iii)(Water soluble matter)	-	2500	-
Cl.No. 6.1,6.2 Table no. 4(iv)(Phosphorus content)	-	2500	-
Cl.No. 6.1,6.2 Table no. 4(v)(Ultraviolet resistance)	-	2500	-
Cl.No. 6.1,6.2 Table no. 4(vi)(Anti-microbial activity value)	-	2500	-
Cl.No. 6.1,6.2 Table no. 4(vii)("Wettability of woven or knitted fabrics (about 150 gsm) made from the yarns")	-	2500	-
Cl.No. 6.1,6.2,8.2. Table no. 4(viii)("Wicking characteristic of woven or knitted fabrics (about 150 gsm) made from the yarn")	-	2500	-
Cl.No. 6.3(Freedom from Yarn Defects)	-	2500	-
Cl.No. 6.4, Table no. 5(Yarn Unevenness and Yarn Imperfections)	-	2500	-
Cl.No. 6.5, Table no. 6(Objectionable Faults)	-	2500	-
Cl.No. 6.6(Commercial Mass)	-	2500	-
Cl.No. 6.7, Table no. 7(i)("Light ")	-	2500	-
Cl.No. 6.7, Table no. 7(ii)(Washing)	-	0	-
Cl.No. 6.7, Table no. 7(iii)(Rubbing)	-	0	-
Cl.No. 6.7, Table no. 7(iv)(Perspiration)	-	0	-
Cl.No. 6.8, Table no. 8(i)(Free and releasable formaldehyde)	-	0	-
Cl.No. 6.8, Table no. 8(ii)("Extractable heavy metals by artificial Acidic sweat/saliva")	-	0	-
Cl.No. 6.8, Table no. 8(iii)(Pentachlorophenol)	-	0	-
Cl.No. 6.8, Table no. 8(iv)(Pesticides (Sum parameter))	-	0	-
Cl.No. 6.8, Table no. 8(v)(Banned Pesticides)	-	0	-
Cl.No. 6.8, Table no. 8(vi)(Banned azo colourants (arylamines))	-	0	-
Cl.No.8(MARKING)	-	0	-
Cl.No. 4(CLASSIFICATIONS)	-	0	-
Cl.No. 5.1, Table no. 1("Designation of Yarn ")	-	0	-
Cl.No.5.2 , Table no. 2(IDENTIFICATION AND DESCRIPTION)	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 3(i)(Mean linear density (Count))	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 3(ii)(Twist per metre,)	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 3(iii)(Average Single yarn tenacity)	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 3(iv)(Elongation)	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 3(v)(Average Count strength product (CSP))	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 3(vi)(Yarn hairiness index)	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 3(vii)(Whiteness index of polyester spun yarn)	-	0	-
Cl.No. 6.1,6.2 Table no. 4(i)(Moisture regain)	-	0	-
Cl.No. 6.1,6.2 Table no. 4(ii)(Isophthalic Acid (IPA) content)	-	0	-
Cl.No. 6.1,6.2 Table no. 4(iii)(Water soluble matter)	-	0	-
Cl.No. 6.1,6.2 Table no. 4(iv)(Phosphorus content)	-	0	-
Cl.No. 6.1,6.2 Table no. 4(v)(Ultraviolet resistance)	-	0	-
Cl.No. 6.1,6.2 Table no. 4(vi)(Anti-microbial activity value)	-	0	-
Cl.No. 6.1,6.2 Table no. 4(vii)("Wettability of woven or knitted fabrics (about 150 gsm) made from the yarns")	-	0	-
Cl.No. 6.1,6.2,8.2. Table no. 4(viii)("Wicking characteristic of woven or knitted fabrics (about 150 gsm) made from the yarn")	-	0	-
Cl.No. 6.3(Freedom from Yarn Defects)	-	0	-
Cl.No. 6.4, Table no. 5(Yarn Unevenness and Yarn Imperfections)	-	0	-
Cl.No. 6.5, Table no. 6(Objectionable Faults)	-	0	-
Cl.No. 6.6(Commercial Mass)	-	0	-
Cl.No. 6.7, Table no. 7(i)("Light ")	-	0	-
Cl.No. 6.7, Table no. 7(ii)(Washing)	-	0	-
Cl.No. 6.7, Table no. 7(iii)(Rubbing)	-	0	-
Cl.No. 6.7, Table no. 7(iv)(Perspiration)	-	0	-
Cl.No. 6.8, Table no. 8(i)(Free and releasable formaldehyde)	-	0	-
Cl.No. 6.8, Table no. 8(ii)("Extractable heavy metals by artificial Acidic sweat/saliva")	-	0	-
Cl.No. 6.8, Table no. 8(iii)(Pentachlorophenol)	-	0	-
Cl.No. 6.8, Table no. 8(iv)(Pesticides (Sum parameter))	-	0	-
Cl.No. 6.8, Table no. 8(v)(Banned Pesticides)	-	0	-
Cl.No. 6.8, Table no. 8(vi)(Banned azo colourants (arylamines))	-	0	-
Cl.No.8(MARKING)	-	0	-

Complete

26 Aug, 2024

IS 1363 : Part 1 (2023)

Hexagon head bolts, screws and nuts of product grade C Part 1 Hexagon head bolts (Size range M5 to M64) (sixth revision)

17200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions)	-	2000	-
5 - Table 5 (i)(General requirements)	-	2000	-
5 - Table 5 (ii)(Thread)	-	2000	-
5 - Table 5 (iii)(Mechanical properties)	-	2000	-
5 - Table 5 (iv)(Tolerances)	-	2000	-
5 - Table 5 (v)(Surface condition)	-	2000	-
5 - Table 5 (vi)(Surface integrity)	-	2000	-
5 - Table 5 (vii)(Acceptability)	-	2000	-
6(Marking and labelling)	-	1200	-
7(Designation)	-	0	-
4(Dimensions)	-	0	-
5 - Table 5 (i)(General requirements)	-	0	-
5 - Table 5 (ii)(Thread)	-	0	-
5 - Table 5 (iii)(Mechanical properties)	-	0	-
5 - Table 5 (iv)(Tolerances)	-	0	-
5 - Table 5 (v)(Surface condition)	-	0	-
5 - Table 5 (vi)(Surface integrity)	-	0	-
5 - Table 5 (vii)(Acceptability)	-	0	-
6(Marking and labelling)	-	0	-
7(Designation)	-	0	-

Complete

26 Aug, 2024

IS 17526 (2021)

STAINLESS STEEL VACUUM FLASKS - SPECIFICATION

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Manufacture and Workmanship)	-	1000	-
5.3(Manufacture and Workmanship)	-	1000	-
7.1.1(Material- Inner containers)	-	1000	-
7.1.2(Outer protective case and accessories - Thickness)	-	1000	-
7.1.2.1(Coating - Limit of lead)	-	1000	-
7.1.2.1(Coating - Limit of Cadmium)	-	1000	-
7.1.4(Auxillary closure "Bisphenol A (BPA)")	-	1000	-
7.3(Capacity)	-	1000	-
7.4(Heat Retention Capability)	-	1000	-
7.5(Cold Retention Capability)	-	1000	-
7.6.1(Drop Impact Test)	-	1000	-
7.6.2(Pendulum Impact Test)	-	1000	-
7.7(Fixing Strength of the Handle)	-	1000	-
7.8(Test for Strength of Shoulder Strap)	-	1000	-
7.8.1(Test for strength of cord)	-	1000	-
7.9(Leakage Test)	-	1000	-
7.10(Joint Leak Test)	-	1000	-
7.11(Staining Test)	-	1000	-
7.12(Length of the Shoulder Strap)	-	1000	-
7.13(Stability of Flask/Bottle)	-	1000	-
7.14(Pour Test)	-	2000	-
9.1(Marking)	-	2000	-
9.2(BIS certification marking)	-	2000	-
10(Packaging)	-	2000	-
5(Manufacture and Workmanship)	-	-	-
5.3(Manufacture and Workmanship)	-	-	-
7.1.1(Material- Inner containers)	-	-	-
7.1.2(Outer protective case and accessories - Thickness)	-	-	-
7.1.2.1(Coating - Limit of lead)	-	-	-
7.1.2.1(Coating - Limit of Cadmium)	-	-	-
7.1.4(Auxillary closure "Bisphenol A (BPA)")	-	-	-
7.3(Capacity)	-	-	-
7.4(Heat Retention Capability)	-	-	-
7.5(Cold Retention Capability)	-	-	-
7.6.1(Drop Impact Test)	-	-	-
7.6.2(Pendulum Impact Test)	-	-	-
7.7(Fixing Strength of the Handle)	-	-	-
7.8(Test for Strength of Shoulder Strap)	-	-	-
7.8.1(Test for strength of cord)	-	-	-
7.9(Leakage Test)	-	-	-
7.10(Joint Leak Test)	-	-	-
7.11(Staining Test)	-	-	-
7.12(Length of the Shoulder Strap)	-	-	-
7.13(Stability of Flask/Bottle)	-	-	-
7.14(Pour Test)	-	-	-
9.1(Marking)	-	-	-
9.2(BIS certification marking)	-	-	-
10(Packaging)	-	-	-

Complete

26 Aug, 2024

IS 9873 : Part 3 (2020)

Safety of Toys Part 3 Migration of Certain Elements ( Third Revision )

3000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	GST @ 18% Extra
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	375	375 GST @ 18% Extra

Complete

26 Aug, 2024

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	2000	-
7(Heating under normal operating conditions)	-	3000	-
8(Constructional requirements with regard to the protection against electric shock)	-	3000	-
9(Electric shock hazard under normal operating conditions)	-	3000	-
10(Insulation requirements)	-	5000	-
11(Fault conditions)	-	5000	-
12(Mechanical strength)	-	5000	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	3000	-
14(Components)	-	0	-
15(TERMINALS)	-	3000	-
16(External flexible cords)	-	4000	-
17(Electrical connections and mechanical fixings)	-	3000	-
19(Stability and mechanical hazards)	-	3000	-
20(Resistance to fire)	-	3000	-

Complete

26 Aug, 2024

IS 16046 : Part 1 (2018)

Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 1 Nickel Systems ( Second Revision )

80000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Parameter Measurement Tolerances)	-	0	Qualitative test
5(General Safety Considerations)	-	0	Qualitative test
5.1(General)	-	0	Qualitative test
5.2(Insulation and Wiring)	-	0	Qualitative test
5.3(Venting)	-	0	Qualitative test
5.4(Temperature, Voltage and Current Management)	-	0	Qualitative test
5.5(Terminal Contacts)	-	0	Qualitative test
5.6(Assembly of Cells into batteries)	-	0	Qualitative test
5.7(Quality Plan)	-	0	Qualitative test
6(Tyoe Test amd Sample Size)	-	0	Qualitative test
7(Specific requirements and tests)	-	0	Qualitative test
7.1(Charging procedure for test purposes)	-	0	Qualitative test
7.2(Intended Use)	-	20000	Charging discharging test range upto 100V & 500A available
7.3(Reasonably foreseeable misuse)	-	45000	Nil
8(Information for safety)	-	5000	Nil
8.1(General)	-	0	Nil
8.2(Small Cell and battery safety information)	-	0	Nil
9(Marking)	-	5000	Nil
9.1(Cell Marking)	-	0	Nil
9.2(Battery Marking)	-	0	Nil
9.4(Other information)	-	0	Nil
10(Packaging)	-	5000	Nil

Complete

26 Aug, 2024

IS 16046 : Part 2 (2018)

70000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Parameter Measurement Tolerances)	-	0	Qualitative Test
5(General Safety Considerations)	-	0	Qualitative Test
5.1(General)	-	0	Qualitative Test
5.2(Insulation and Wiring)	-	0	Qualitative Test
5.3(Venting)	-	0	Qualitative Test
5.4(Temperature, Voltage and Current Management)	-	0	Qualitative Test
5.5(Terminal Contacts)	-	0	Qualitative Test
5.6(Assembly of Cells into batteries)	-	0	Qualitative Test
5.7(Quality Plan)	-	0	Qualitative Test
5.8(Battery Safety Components)	-	0	Qualitative Test
6(Type Test and Sample Size)	-	0	Qualitative Test
7(Specific requirements and tests)	-	0	Qualitative Test
7.1(Charging procedure for test purposes)	-	0	Test capacity upto 100V , 400A
7.2(Intended Use)	-	10000	Nil
7.3(Reasonably foreseeable misuse)	-	50000	Test capacity upto 100V , 400A
8(Information for safety)	-	5000	Nil
8.1(General)	-	0	Qualitative Test
8.2(Small Cell and battery safety information)	-	0	Qualitative Test
9(Marking)	-	5000	Nil
9.1(Cell Marking)	-	0	Qualitative Test
9.2(Battery Marking)	-	0	Qualitative Test
9.3(Caution for ingestion of small cells and batteries)	-	0	Qualitative Test
9.4(Other information)	-	0	Qualitative Test
10(Packaging)	-	0	Qualitative Test

Complete

26 Aug, 2024

IS 12444 (2020)

Copper Wire Rods for Electrical Applications — Specification ( First Revision )

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table-1(Te)	-	1000	-
5.1 Table-1(Se)	-	1000	-
5.1 Table-1(Bi)	-	1000	-
5.1 Table-1(Se+Te+Bi)	-	1000	-
5.1 Table-1(Sb)	-	1000	-
5.1 Table-1(As)	-	1000	-
5.1 Table-1(Sn)	-	1000	-
5.1 Table-1(Pb)	-	1000	-
5.1 Table-1(Fe)	-	1000	-
5.1 Table-1(Ni)	-	1000	-
5.1 Table-1(S)	-	1000	-
5.1 Table-1(Ag)	-	1000	-
5.1 Table-1(O)	-	1000	-
5.1 Table-1(Maximum Allowable Total Impurities)	-	1000	-
6.1(Dimension)	-	1000	-
6.2.2(Ovality)	-	1000	-
7.0(Freedom from Defects)	-	1000	-
8.1(Tensile Strength)	-	1000	-
8.2(Surface Compression Test)	-	2000	-
Cl-9.1, Table-4(Volume Resistivity)	-	2000	-
Cl-9.1, Table-4(Mass Resistivity)	-	2000	-
Cl-9.1, Table-4(Electrical Conductivity)	-	2000	-
7.2(Surface Oxide)	-	2000	-
10.5(Microscopic Examination)	-	2000	-

Complete

26 Aug, 2024

IS 21 (1992)

Wrought aluminium and aluminium alloys for manufacture of utensils specification (Fourth Revision)

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, WP')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'W')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 64430, 'O')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H4')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H3')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H2')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-B, 'H1')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H3')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H2')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'H1')(0.2 Percent Proof Stress)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 51000-A, 'O')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H4')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H3')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H2')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'H1')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'O')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 40800, 'O')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H4')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H3')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H2')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'H1')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'O')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31500, 'O')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H4')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H3')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H2')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'H1')(Tensile Strength)	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Bend Test (Radius of Bend))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	100	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 31000, 'O')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H4')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'H2')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19600, 'O')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H4')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'H2')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19500, 'O')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H4')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H3')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H2')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'H1')(Tensile Strength)	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Bend Test (Radius of Bend))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 2.6 to 6.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness over 1.3 to 2.6 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.8 to 1.3 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Elongation on 50 mm gauge length (For thickness 0.5 to 0.8 mm))	-	0	-
4.2, Table 2 of IS:21 (Designation & Condition 19000, 'O')(Tensile Strength)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Titanium and or other grain refining elements)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 64430)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-B)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 51000-A)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Titanium and or other grain refining elements)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 40800)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Titanium and or other grain refining elements)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 31500)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Chromium)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Titanium and or other grain refining elements)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 31000)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Cu+Si+Fe+Mn+Zn)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 19600)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Cu+Si+Fe+Mn+Zn)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 19500)(Copper)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Lead)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Aluminium)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Zinc)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Manganese)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Iron)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Silicon)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Magnesium)	-	0	-
4.2, Table 1of IS:21 (Designation 19000)(Copper)	-	0	-
4.1, & 4.1.1(Lead)	-	0	-
4.1.2(Aluminium)	-	0	-
5(Marking)	-	0	-

Complete

26 Aug, 2024

IS 7534 (1985)

Specificaiton for sliding locking bolts for use with padlocks

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 table 2(DIMENSIONS OF LOCKING BOLT)	-	2000	-
5.1 table 2(1. The locking bolts shall have smooth sliding action. 2. All sharp edges and corners shall be removed and finished smooth. 3. All screw holes shall be countersunk to suit the countersunk head wood screws)	-	2000	-
7.1(Mild steel locking bolts copper oxidized)	-	2000	-
7.1(Mild steel locking bolts Electrogalvanised)	-	2000	-
7.1(Aluminium alloy bolt anodized)	-	2000	-
7.1(Anodic Coatic)	-	2000	-
5.1.1(Bolt Plate)	-	3000	-
5.1.2(Bolt)	-	3000	-
4(Mild steel sheet, Aluminium alloy sheet)	-	2000	-

Complete

26 Aug, 2024

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 1(chemical composition)	-	8500	-
5.1 table 2(0.2% proof strength)	-	2500	-
5.1 table 2(Tensile strength)	-	2000	-
5.1 table 2(Elongation)	-	3000	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 204 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 204 electric water boilers

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(GENERAL REQUIREMENT)	-	0	-
4(GENERAL NOTES ON TESTS)	-	0	-
5(RATING)	-	200	5% Discount For BIS
6(CLASSIFICATION)	-	300	-
7(MARKING)	-	500	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	3000	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	0	-
10(INPUT AND CURRENT)	-	5000	-
11(TEMPRATURE RISE)	-	5000	-
12(OPERATION TJNDER OVERLOAD CONDITIONS OF APPLIANCES WITH HEATING ELEMENTS)	-	3000	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	5000	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	2000	-
15(MOISTURE RESISTANCE)	-	10000	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	2500	-
17(OVERLOAD PROTECTION)	-	5000	-
18(ENDURANCE )	-	0	-
19(ABNORMAL OPERATION)	-	5000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	3000	-
21(MECHANICAL STRENGTH)	-	2500	-
22(CONSTRUCTION)	-	1500	-
23(INTERNAL WIRING)	-	3000	-
24(COMPONENTS)	-	5000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	5000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1000	-
27(PROVISION FOR EARTHING)	-	1000	-
28(SCREWS AND CONNECTIONS)	-	2500	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	1000	-
30(RESISTANCE TO HEAT, FIRE AND TACKING)	-	1000	-
31(RESISTANCE TO RUSTING)	-	1000	-
32(RADIATION HAZARDS)	-	1000	-
101.1(Type Tests)	-	0	-
101.2(Acceptance Tests)	-	0	-
101.3(Routine Tests)	-	0	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 203 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 203 electric call bells and buzzers for indoor use

22100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	100	5% Discount for BIS
6(Classification)	-	100	-
7(Marking)	-	200	-
8(Protection against Access to Live Parts)	-	500	-
9(Starting Of Motor Operated Appliances)	-	0	-
10("Power Input & Current")	-	0	-
11(Temperature Rise/ Heating)	-	2000	-
12(Operation Under Overload Conditions of Appliances with heating Element)	-	0	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1500	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	1000	-
15(Moisture Resistance)	-	3000	-
16(Leakage Current and Electric Strength/ Insulation Resistance and Electric Strength (After Humidity treatment))	-	2000	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	0	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	0	-
20(Stability & Mechanical Hazards)	-	0	-
21(Mechanical strength)	-	1000	-
22(Construction)	-	500	-
23(Internal Wiring)	-	500	-
24(Components)	-	1000	-
25(Supply Connection & External Flexible Cords)	-	1500	-
26(Terminals For External Conductors)	-	1000	-
27(Provision For Earthing)	-	1000	-
28(Screws & Connections)	-	500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	2000	-
30(Resistance to Heat & Fire)	-	1000	-
31(Resistance to Rusting)	-	1000	-
32(Radiation hazards)	-	700	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 59 (1999)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 59 insect killers

32000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 32 302-2-59 : 1999(Radiation Hazards)	-	1000	5% Discount for BIS
Cl. 31 302-2-59 : 1999(Resistance to Rusting)	-	1500	-
Cl. 30 302-2-59 : 1999(Resistance to Heat Fire & Tracking )	-	1500	-
Cl. 29 302-2-59 : 1999(Clearances, Creepage Distances & Solid insulation )	-	1000	-
Cl. 28 302-2-59 : 1999(Screws & Connections)	-	1000	-
Cl. 27 302-2-59 : 1999(Provision for Earthing )	-	1500	-
Cl. 26 302-2-59 : 1999(Terminals for External conductors )	-	500	-
Cl. 25 302-2-59 : 1999(Supply Connection & External Flexible Cords)	-	1500	-
Cl. 24 302-2-59 : 1999(Components)	-	700	-
Cl. 23 302-2-59 : 1999(Internal Wiring)	-	500	-
Cl. 22 302-2-59 : 1999(Construction )	-	1000	-
Cl. 21 302-2-59 : 1999(Mechanical strength)	-	1000	-
Cl. 20 302-2-59 : 1999(Stability & Mechanical Hazards)	-	1500	-
Cl. 19 302-2-59 : 1999(Abnormal Operation )	-	2500	-
Cl. 18 302-2-59 : 1999(Endurance)	-	0	-
Cl. 17 302-2-59 : 1999(Overload Protection of Transformers and Associated Circuit)	-	1000	-
Cl. 16 302-2-59 : 1999(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	2500	-
Cl. 15 302-2-59 : 1999(Moisture Resistance Test )	-	3000	-
Cl. 14 302-2-59 : 1999(Radio and television interference suppression / Transient over voltages)	-	500	-
Cl. 13 302-2-59 : 1999(Leakage Current & Electric Strength at Operating Temperature)	-	1500	-
Cl. 11 302-2-59 : 1999(Temperature Rise)	-	3500	-
Cl. 10 302-2-59 : 1999(Power Input and Current )	-	2000	-
Cl. 9 302-2-59 : 1999(Starting of motor operated appliances)	-	500	-
Cl. 8 302-2-59 : 1999(Protection Against Electric Shock )	-	600	-
Cl. 7 302-2-59 : 1999(Marking)	-	100	-
(CI. 6 IS 302-2-59 : 1999(Classification )	-	100	-
Cl. 32 302-2-59 : 1999(Radiation Hazards)	-	0	-
Cl. 31 302-2-59 : 1999(Resistance to Rusting)	-	0	-
Cl. 30 302-2-59 : 1999(Resistance to Heat Fire & Tracking )	-	0	-
Cl. 29 302-2-59 : 1999(Clearances, Creepage Distances & Solid insulation )	-	0	-
Cl. 28 302-2-59 : 1999(Screws & Connections)	-	0	-
Cl. 27 302-2-59 : 1999(Provision for Earthing )	-	0	-
Cl. 26 302-2-59 : 1999(Terminals for External conductors )	-	0	-
Cl. 25 302-2-59 : 1999(Supply Connection & External Flexible Cords)	-	0	-
Cl. 24 302-2-59 : 1999(Components)	-	0	-
Cl. 23 302-2-59 : 1999(Internal Wiring)	-	0	-
Cl. 22 302-2-59 : 1999(Construction )	-	0	-
Cl. 21 302-2-59 : 1999(Mechanical strength)	-	0	-
Cl. 20 302-2-59 : 1999(Stability & Mechanical Hazards)	-	0	-
Cl. 19 302-2-59 : 1999(Abnormal Operation )	-	0	-
Cl. 18 302-2-59 : 1999(Endurance)	-	0	-
Cl. 17 302-2-59 : 1999(Overload Protection of Transformers and Associated Circuit)	-	0	-
Cl. 16 302-2-59 : 1999(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	0	-
Cl. 15 302-2-59 : 1999(Moisture Resistance Test )	-	0	-
Cl. 14 302-2-59 : 1999(Radio and television interference suppression / Transient over voltages)	-	0	-
Cl. 13 302-2-59 : 1999(Leakage Current & Electric Strength at Operating Temperature)	-	0	-
Cl. 11 302-2-59 : 1999(Temperature Rise)	-	0	-
Cl. 10 302-2-59 : 1999(Power Input and Current )	-	0	-
Cl. 9 302-2-59 : 1999(Starting of motor operated appliances)	-	0	-
Cl. 8 302-2-59 : 1999(Protection Against Electric Shock )	-	0	-
Cl. 7 302-2-59 : 1999(Marking)	-	0	-
(CI. 6 IS 302-2-59 : 1999(Classification )	-	0	-
Cl-9 (Cl-19.11.4.1 of IS 302-1)(Electrostatic discharge)	-	10000	Extra EMI/EMC Charge: 180000/-
Cl-9 (Cl-19.11.4.2 of IS 302-1)(Radiated Fields)	-	80000	-
Cl-9 (Cl-19.11.4.3 of IS 302-1)(Fast transient bursts)	-	10000	-
Cl-9 (Cl-19.11.4.4 of IS 302-1)(Surge Immunity test)	-	10000	-
Cl-9 (Cl-19.11.4.5 of IS 302-1)(Immunity to conducted discharge)	-	50000	-
Cl-9 (Cl-19.11.4.6 of IS 302-1)(Voltage dips and interruptions)	-	10000	-
Cl-9 (Cl-19.11.4.7 of IS 302-1)(Harmonics)	-	10000	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 45 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 45 electric heating tools

34500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	100	5% Discount for BIS
6(Classification)	-	0	-
7(Marking)	-	100	-
8(Protection against Access to Live Parts)	-	500	-
9(Starting Of Motor Operated Appliances)	-	1000	-
10("Power Input & Current")	-	5000	-
11(Temperature Rise/ Heating)	-	2000	-
12(Operation Under Overload Condition)	-	2000	-
13(Electric Insulation at Operating Temperature)	-	1750	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	500	-
15(Moisture Resistance)	-	3000	-
16(Insulation Resistance and Electric Strength/ Leakage Current and Electric Strength (After Humidity Treatment))	-	2100	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1000	-
18(Endurance)	-	0	-
19(Abnormal Operation)	-	2500	Extra EMI/EMC Charge: 180000
20(Stability & Mechanical Hazards)	-	1500	-
21(Mechanical strength)	-	1000	-
22(Construction)	-	1000	-
23(Internal Wiring)	-	300	-
24(Components)	-	500	-
25(Supply Connection & External Flexible Cords)	-	1000	-
26(Terminals For External Conductors)	-	500	-
27(Provision For Earthing)	-	1250	-
28(Screws & Connections)	-	700	-
29(Creepage Distances & Clearances)	-	600	-
30(Resistance to Heat, Fire and Tracking)	-	1500	-
31(Radiation hazards)	-	1500	-
XXV of Table 101(Resistance to Rusting)	-	1500	-
4(General Requirement)	-	0	-
19.11.4.7(Harmonics)	-	10000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	10000	-
19.11.4.5(Immunity to conducted discharges)	-	50000	-
19.11.4.4(Surge immunity test)	-	10000	-
19.11.4.3(Fast transient bursts)	-	10000	-
19.11.4.2(Radiated fields)	-	80000	-
19.11.4.1(Electrostatic discharges)	-	10000	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 32 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 32 massage appliances

34500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 32 302-2-32 : 1994(Radiation Hazards)	-	1500	5% Discount for BIS
Cl. 31 302-2-32 : 1994(Resistance to Rusting)	-	1500	-
Cl. 30 302-2-32 : 1994(Resistance to Heat Fire & Tracking )	-	1500	-
Cl. 29 302-2-32 : 1994(Clearances, Creepage Distances & Solid insulation )	-	600	-
Cl. 28 302-2-32 : 1994(Screws & Connections)	-	700	-
Cl. 27 302-2-32 : 1994(Provision for Earthing )	-	1250	-
Cl. 26 302-2-32 : 1994(Terminals for External conductors )	-	500	-
Cl. 25 302-2-32 : 1994(Supply Connection & External Flexible Cords)	-	1000	-
Cl. 24 302-2-32 : 1994(Components)	-	500	-
Cl. 23 302-2-32 : 1994(Internal Wiring)	-	300	-
Cl. 22 302-2-32 : 1994(Construction )	-	1000	-
Cl. 21 302-2-32 : 1994(Mechanical strength)	-	1000	-
Cl. 20 302-2-32 : 1994(Stability & Mechanical Hazards)	-	1500	-
Cl. 19 302-2-32 : 1994(Abnormal Operation )	-	2500	-
Cl. 18 302-2-32 : 1994(Endurance)	-	0	-
Cl. 17 302-2-32 : 1994(Overload Protection of Transformers and Associated Circuit)	-	1000	-
Cl. 16 302-2-32 : 1994(Leakage Current & Electric Strength at Operating Temperature (After Humidity Treatment))	-	2100	-
Cl. 15 302-2-32: 1994(Moisture Resistance Test )	-	3000	-
Cl. 14 302-2-32 : 1994(Radio and television interference suppression / Transient over voltages)	-	1500	-
Cl. 13 302-2-32 : 1994(Leakage Current & Electric Strength at Operating Temperature)	-	1850	-
Cl. 11 302-2-32 : 1994(Temperature Rise)	-	2000	-
Cl. 10 302-2-32 : 1994(Power Input and Current )	-	5000	-
Cl. 9 302-2-32 : 1994(Protection Against Electric Shock)	-	1000	-
Cl. 8 302-2-32 : 1994(Starting of motor operated appliances)	-	500	-
Cl. 7 302-2-32 : 1994(Marking)	-	100	-
(CI. 6 IS 302-2-32 : 1994(Classification )	-	200	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 13 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 13 frying pans, deep fat fryers and similar appliances

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation ,Toxicity and similar hazards)	-	1400	5% Discount For BIS
31(Resistance to Rusting)	-	1500	-
30(Resistance to Heat, Fire and Tracking)	-	2500	-
29(Clearances, Creepage Distances & Solid Insulation)	-	500	-
28(Screws & Connections)	-	1000	-
27(Provision For Earthing)	-	1500	-
26(Terminals For External Conductors)	-	1000	-
25(Supply Connection & External Flexible Cables and Cords)	-	1000	-
24(Components)	-	1500	-
23(Internal wiring)	-	2500	-
22(Construction)	-	3000	-
21(Mechanical strength)	-	2500	-
20(Stability & Mechanical Hazards)	-	2500	-
19(Abnormal Operation)	-	5000	-
18(Endurance)	-	0	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	1500	-
16(Leakage Current and Electric Strength)	-	2000	-
15(Moisture Resistance)	-	8000	-
14(Transient Over Voltage)	-	1500	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	2000	-
11(Temperature Rise/Heating)	-	5000	-
10(Power Input)	-	3000	-
9(Starting Of Motor Operated Appliances)	-	1000	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	1000	-
7(Marking/ Marking & Instructions)	-	300	-
6(Classification)	-	200	-
5(Rating)	-	100	-
19.11.4.1(Electrostatic discharges)	-	10000	Extra EMI/EMC Charge: 180000/-
19.11.4.2(Radiated fields)	-	80000	-
19.11.4.3(Fast transient bursts)	-	10000	-
19.11.4.4(Surge immunity test)	-	10000	-
19.11.4.5(Immunity to conducted discharges)	-	50000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	10000	-
19.11.4.7(Harmonics)	-	10000	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 11 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 11 tumbler dryers

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(GENERAL REQUIREMENT)	-	0	-
4(GENERAL NOTES ON TESTS)	-	0	-
5(RATING)	-	100	-
6(CLASSIFICATION)	-	100	-
7(MARKING)	-	100	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	500	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	500	-
10(INPUT AND CURRENT)	-	1500	-
11(HEATING)	-	2000	-
12(OPERATION TJNDER OVERLOAD CONDITIONS OF APPLIANCES WITH HEATING ELEMENTS)	-	0	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	1500	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	1000	-
15(MOISTURE RESISTANCE)	-	2500	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	1000	-
17(OVERLOAD PROTECTION)	-	500	-
18(ENDURANCE )	-	0	-
19(ABNORMAL OPERATION)	-	2000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	1500	-
21(MECHANICAL STRENGTH)	-	1000	-
22(CONSTRUCTION)	-	1000	-
23(INTERNAL WIRING)	-	500	-
24(COMPONENTS)	-	500	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	1000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	500	-
27(PROVISION FOR EARTHING)	-	500	-
28(SCREWS AND CONNECTIONS)	-	500	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	700	-
30(RESISTANCE TO HEAT, FIRE AND TACKING)	-	1000	-
31(RESISTANCE TO RUSTING)	-	1500	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	1000	-
101.1(Type Tests)	-	500	-
101.2(Acceptance Tests)	-	500	-
101.3(Routine Tests)	-	500	-

Complete

26 Aug, 2024

IS 302 : Part 2 : Sec 8 (1994)

Safety of household and similar electrical appliances : part 2 particular requirements, section 8 electrical shavers hair, clippers and similar appliances

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32(Radiation ,Toxicity and similar hazards)	-	1500	5% Discount for BIS
31(Resistance to Rusting)	-	1500	-
30(Resistance to Heat & Fire)	-	1000	-
29(Clearances, Creepage Distances & Solid Insulation)	-	700	-
28(Screws & Connection)	-	500	-
27(Provision For Earthing)	-	500	-
26(Terminals For External Conductors)	-	500	-
25(Supply Connection & External Flexible Cables and Cords)	-	1000	-
24(Component)	-	500	-
23(Internal wiring)	-	500	-
22(Construction)	-	1000	-
21(Mechanical strength)	-	1000	-
20(Stability & Mechanical Hazards)	-	1500	-
19(Abnormal Operation)	-	2000	-
18(Endurance)	-	0	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	500	-
16(Leakage Current and Electric Strength)	-	1000	-
15(Moisture Resistance)	-	2500	-
14(Radio and Television Interference Suppression/ Transient Over Voltage)	-	1000	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	1500	-
11(Temperature Rise/Heating)	-	2000	-
10(Power Input & Current)	-	1500	-
9(Starting Of Motor Operated Appliances)	-	500	-
8(Protection against Electric Shock/ Protection against Access to Live Parts)	-	500	-
7(Marking/ Marking & Instructions)	-	100	-
6(Classification)	-	100	-
5(Rating)	-	100	-
19.11.4.1(Electrostatic discharges)	-	10000	-
19.11.4.2(Radiated fields)	-	80000	-
19.11.4.3(Fast transient bursts)	-	10000	-
19.11.4.4(Surge immunity test)	-	10000	-
19.11.4.5(Immunity to conducted discharges)	-	50000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	10000	-
19.11.4.7(Harmonics)	-	10000	-

Complete

26 Aug, 2024

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	1000	-
8(Mechanical and Physical Properties)	-	1000	-
Cl 8(UTM)	-	1000	-
Cl 9(Workmanship)	-	1000	-
Cl 9.6(Workmanship)	-	1000	-
Cl 10(Workmanship)	-	1000	-
Cl 11(Length, Width & Thickness)	-	1000	-
Cl 8(UTM)	-	1000	-
Cl 9.5(Workmanship)	-	1000	-
Cl 9.6(Workmanship)	-	1000	-
Cl 10(Workmanship)	-	1000	-
Cl 11(Length, Width & Thickness)	-	1000	-
Cl 8(UTM)	-	1000	-
Cl 9(Workmanship)	-	1000	-
Cl 9.6(Workmanship)	-	1000	-
Cl 10(Workmanship)	-	1000	-
Cl 11(Length, Width & Thickness)	-	1000	-
7.0(ALUMINIUM)	-	1000	-
7.0(MICRO ALLOYS)	-	1000	-
7.0(NITROGEN)	-	1000	-
7.0(SILICON)	-	1000	-
7.0(MANGANESE)	-	1000	-
7.0(PHOSPHORUS)	-	1000	-
7.0(SULPHUR)	-	1000	-
7.0(CARBON)	-	1000	-
Cl. 11(Out of square)	-	0	-
Cl. 11(Flatness)	-	0	-
Cl. 11(Camber)	-	0	-
Cl. 11(Width)	-	0	-
Cl. 11(Thickness)	-	0	-
Cl. 8.7(Bake Hardening Index)	-	0	-
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	0	-
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	0	-
Cl. 8.4(Bend Test)	-	0	-
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	0	-
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 80 mm gauge length)	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 50 mm gauge length)	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Yield Stress)	-	0	-
Cl. 9 Table 8(Surface roughness)	-	0	-
Cl 11(Length, Width & Thickness)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 8(UTM)	-	0	-
Cl 8(UTM)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	0	-
Cl 7(UTM)	-	0	-
8.1(Mechanical)	-	0	-
8.2(Cupping test)	-	0	-
8.3(Hardness HRB/HV)	-	0	-
8.4(Bend Test)	-	0	-
8.5(Plastic strain ratio)	-	0	-
8.6(Tensile strain Hardening component)	-	0	-
8.7(Black Hardening Index)	-	0	-
9(Surface finish)	-	0	-
10(Freedom from defects)	-	0	-
13(Marking)	-	0	-
Cl. 7.3(Carbon)	-	0	-
Cl. 7.3(Manganese)	-	0	-
Cl. 7.3(Suphur)	-	0	-
Cl. 7.3(Phosphorus)	-	0	-
Cl. 7.3(Silicon)	-	0	-

Complete

26 Aug, 2024

IS/IEC 62368 : Part 1 (2018)

Audio / Video, Information and Communication Technology Equipment Part 1 Safety Requirements ( First Revision )

85000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4, 4.1, 4.1.1, 4.1.2, 4.1.3, 4.1.4, 4.1.5, 4.1.6, 4.1.7, 4.1.8, 4.1.9,4.1.10, 4.1.11,4.1.12, 4.1.13, 4.1.14,4.1.15(General Requirements)	-	2500	-
Cl. 4.2, 4.2.1, 4.2.2, 4.2.3, 4.2.4(Energy source classifications)	-	2000	-
Cl. No. 4.3 ,4.4,4.5, 4.6,4.7,4.8,4.9,4.10 with all sub clauses(Protection against energy sources)	-	3500	-
Cl. No. 5,5.1,5.2,5.3,5.4,5.5,5.6,5.7,5.8 with all sub clauses(Electrically-caused injury)	-	5000	-
Cl No. 6,6.1,6.2,6.3,6.4,6.5,6.6 with all sub clause(Electrically-caused fire)	-	2000	-
Cl. 8,8.1,8.2,8.3,8.4,8.5,8.6,8.7,8.8,8.9,8.10,8.11,8.12 with all sub clause(Mechanically-caused injury)	-	2500	-
Cl. 7, 7.1, 7.2, 7.3, 7.4, 7.5, 7.6(Injury caused by hazardous substances)	-	4000	-
Cl. 9, 9.1, 9.2, 9.2.1,9.2.2, 9.2.3, 9.3, 9.3.1, 9.3.2, 9.4, 9.5, 9.5.1, 9.5.2, 9.6, 9.6.1, 9.6.2, 9.6.3(Thermal burn injury)	-	5000	-
Annex. B, B.1, B.1.1, B.1.2, B.1.3, B.1.4, B.1.5,B.2,B.2.1, B.2.2, B.2.3, B.2.4, B.2.5, B.2.6, B.2.6.1, B.2.6.2, B.2.6.3, B.2.7, B.3, B.3.1, B.3.2, B.3.3, B.3.4, B.3.5, B.3.6, B.3.7, B.3.8, B.4, B.4.1, B.4.2, B.4.3, B.4.3.1, B.4.3.2,B.4.4, B.4.4.1, B.4.4.(Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	3000	-
Annex. D, D.1, D.2, D.3(Test Generators)	-	500	-
Annex E, E.1, E.2, E.3(Test conditions)	-	500	-
Annex. F, F.1, F.2, F2.1, F.2.2,F2.3,F.3, F.3.1, F.3.2, F.3.2.1,F.3.2.2, F.3.3,F.3.3.1, F.3.3.2,F.3.3.3, F.3.3.4, F.3.3.5, F.3.3.6,F.3.3.7, F.3.3.8, F.3.4, F.3.5, F.3.5.1,F.3.5.2, F.3.5.3, F.3.5.4, F.3.5.5,F.3.5.6, F.3.5.7,F.3.6, F.3.6.1, F.3.6.1.1, F.3.6(Equipment markings, instructions, and instructional safeguards)	-	3000	-
Annex. G, G.1, G.1.1, G.1.2, G.1.3, G.2, G.2.1, G.2.2, G.2.3, G.2.4, G.3, G.3.1, G.3.1.1, G.3.1.2, G.3.2, G.3.2.1,G.3.2.2, G.3.3,G.3.4, G.3.5, G.3.5.1, G.3.5.2, G.4, G.4.1, G.4.2, G.4.3, G.5, G.5.1, G.5.1.1, G.5.1.2,G.5.1.3,G.5.2,G.5.2.1, G.5.2.2, G.5.2.3(Components)	-	4000	-
Annex I(Overvoltage categories)	-	500	-
Annex. J, J.1, J.2, J.2.1, J.2.2, J.2.2.1, J.2.2.1.1, J.2.2.1.2, J.2.2.1.3, J.2.2.2, J.2.3, J.2.4, J.2.5, J.3, J.3.1, J.3.2, J.3.3(Insulated winding wires for use without interleaved insulation)	-	6000	-
Annex. K, K.1, K.1.1, K.1.2, K.2, K.3, K.4, K.5, K.5.1, K.5.2, K.6, K.6.1, K.6.2, K.7, K.7.1, K.7.2, K.7.3, K.7.4(Safety Interlocks)	-	3000	-
Annex. L, L.1, L.2, L.3, L.4, L.5, L.6, L.7, L.8, L.9,(Disconnect devices)	-	1000	-
Annex. M, M.1, M.2, M.2.1, M.2.2, M.3, M.3.1, M.3.2, M.3.3, M.4, M.4.1, M.4.2,M.4.2.1, M.4.2.2,M.4.3, M.4.4,M.4.4.1, M.4.4.2,M.4.4.3, M.4.4.4, M.4.4.5, M.4.4.6, M.5, M.5.1, M.5.2, M.6, M.6.1, M.6.2, M.7, M.7.1, M.7.2, M.7.3, M.7.3.1,M.7.3.2, M.7.3.3, M.7.(Equipment containing batteries and their protection circuits)	-	4000	-
Annex. N(Electrochemical potentials)	-	500	-
Annex. O(Measurement of creepage distances and clearances)	-	2000	-
Annex. P, P.1, P.2, P.2.1, P.2.2, P.2.3, P.2.3.1, P.2.3.2, P.3, P.3.1, P.3.2, P.3.3, P.3.4, P.4, P.4.1, P.4.2(Safeguards against conductive objects)	-	3000	-
Annex. Q, Q.1, Q.1.1, Q.1.2, Q.2(Circuits intended for interconnection with building wiring)	-	5000	-
Annex. R, R.1, R.2, R.3, R.4(Limited short-circuit test)	-	6000	-
Annex. S, S.1, S.2, S.3, S.3.1, S.3.2, S.4, S.5(Tests for resistance to heat and fire)	-	6000	-
Annex. T, T.1, T.2, T.3, T.4, T.5, T.6, T.7, T.8, T.9, T.10, T.11(Mechanical strength tests)	-	5000	-
Annex. V, V.1, V.1.1, V.1.2, V.1.3, V.1.4, V.1.5, V.1.6, V.2(Determination of accessible parts)	-	4000	-
Annex. X(Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420V peak (300V rms))	-	500	-
Annex. Y, Y.1, Y.2, Y.3, Y.3.1, Y.3.2, Y.3.3, Y.3.4, Y.3.5, Y.4, Y.4.1 Y.4.2, Y.4.3, Y.4.4, Y.4.5, Y.5, Y.5.1, Y.5.2, Y.5.3, Y.5.4, Y.5.5, Y.5.5.1, Y.5.5.2, Y.5.5.3, Y.6, Y.6.1, Y.6.2(Construction requirements for outdoor enclosure)	-	1000	-

Complete

26 Aug, 2024

IS 16333 : Part 3 (2022)

Mobile phone handsets: Part 3 Indian language support for mobile phone handsets - Specific requirements(Second Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1(Inputting of text)	-	15000		-
5.2(Message Readability)	-	15000		-

Complete

26 Aug, 2024

IS 1989 : Part 1 (1986)

Specification for leather safety boots and shoes: Part 1 for miners (Fourth Revision)

----

23000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 (a)(Marking)	-	1150	-
4.1 (b)(Marking)	-	1150	-
4.1 (c)(Marking)	-	1150	-
4.1 (d)(Marking)	-	1150	-
4.1 (e)(Marking)	-	1150	-
7.1(Design)	-	1150	-
10.1(Finish)	-	1150	-
10.3(Finish)	-	1150	-
10.4(Finish)	-	1150	-
11.1(Mass Boots with Leather Sole and Heel)	-	1150	-
11.2(Mass Boots with Rubber Sole and Heel)	-	1150	-
12(Performance test)	-	1150	-
13(Design)	-	1150	-
16.1(Finish)	-	1150	-
16.2(Finish)	-	1150	-
16.3(Finish)	-	1150	-
16.4(Finish)	-	1150	-
17.1(Mass Shoes with Leather Sole and Heel)	-	1150	-
17.2(Mass Shoes with Rubber Sole and Heel)	-	1150	-
18(Performance test)	-	1150	-

Complete

26 Aug, 2024

IS 6719 (1972)

Solid Pvc Soles And Heels

4800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	400	-
3.6 (vi)(Lead (as Pb) ppm)	-	400	-
3.6 (v)(Volatility, percent by means )	-	400	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	400	-
3.6 (iii)(Elongation at break, percent )	-	400	-
3.6 (ii)(Tensile Strength )	-	400	-
3.6 (i)(Relative density )	-	400	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	400	-
6 ,6.1,6.2,6.3(Test Method)	-	400	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	400	-
Cl. 6.4(Measurement of thickness)	-	400	-

Complete

26 Aug, 2024

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, ii)(Hardness, Shore A durometer min)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vii)(Heat shrinkage test at 100±1°C for 1 hour max)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii)(Water absorption , percent by mass, Max)	-	333	-
Cl.4 Cl.4.1.3 And 8.3,Table1, ix)(Flexing resistance)	-	333	-
5, 5.1(Marking)	-	333	-
4.2(Size & Thickness )	-	333	-
6, 6.1(Packing)	-	333	-
"Cl.4 ,Cl.4.1,4.1.1,4.1.2(Requirements ")	-	333	-
Cl.4.1.3 And 8.3,Table1(i) Relative density)	-	333	-
Cl.4.1.3 And 8.3,Table1(ii) Hardness, Shore A durometer min)	-	333	-
Cl.4.1.3 And 8.3,Table1(iii) Change in Hardness after ageing at 100±1°C for 24hr)	-	333	-
Cl.4.1.3 And 8.3,Table1(iv) Compression set at constant stress percent, Max)	-	333	-
Cl.4.1.3 And 8.3,Table1(vi) Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	333	-
Cl.4.1.3 And 8.3,Table1(vii) Heat shrinkage test at 100±1°C for 1 hour max)	-	333	-
Cl.4.1.3 And 8.3,Table1(viii)Water absorption , percent by mass, Max)	-	333	-
Cl.4.1.3 And 8.3,Table1(ix)Flexing resistance)	-	333	-
5, 5.1(Marking)	-	333	-
6, 6.1(Packing)	-	333	-

Complete

26 Aug, 2024

IS 1989 : Part 2 (1986)

Specification for leather safety boots and shoes: Part 2 for heavy metal industries (Fourth Revision)

----

23000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Marking)	-	242	-
7(Design)	-	158	-
8(a) Upper Leather)	-	158	-
8(b) Lining Leather)	-	158	-
8(c) Bottom Material)	-	158	-
8(d) Steel Toe Cap)	-	158	-
8(e) Tape)	-	158	-
8(f) Bottom Filling)	-	158	-
8(g) Eyelet)	-	158	-
8(h) Toe Compound)	-	158	-
8(i) Threads)	-	158	-
8(j) Rivets)	-	158	-
8(k) Screw Wire)	-	158	-
8(l) Heel Pin)	-	158	-
8(m) Shank)	-	158	-
8(n) Laces)	-	158	-
8(o) Tongue Lining)	-	158	-
8(p) Adhesive)	-	158	-
8(q) Strengthening Piece)	-	158	-
8(r) Leather Components)	-	158	-
9(Manufacture)	-	158	-
10(Finish)	-	158	-
11(a) Boots with Leather Sole and Heel)	-	158	-
11(b) Boots with Rubber Sole and Heel)	-	158	-
12(Performance Test)	-	158	-
13(Design)	-	158	-
14(a) Upper Leather)	-	158	-
14(b) Lining Leather)	-	158	-
14(c) Bottom Material)	-	158	-
14(d) Steel Toe Cap)	-	158	-
14(e) Tape)	-	158	-
14(f) Bottom Filling)	-	158	-
14(g) Eyelet)	-	158	-
14(h) Toe Compound)	-	158	-
14(i) Threads)	-	158	-
14(j) Rivets)	-	158	-
14(k) Screw Wire)	-	158	-
14(l) Heel Pin)	-	158	-
14(m) Shank)	-	158	-
14(n) Laces)	-	158	-
14(o) Tongue Lining)	-	158	-
14(p) Adhesive)	-	158	-
14(q) Leather Components)	-	158	-
15(Manufacture)	-	158	-
16(Finish)	-	158	-
17(a) Shoes with Leather Sole and Heel)	-	158	-
17(b) Shoes with Rubber Sole and Heel)	-	158	-
18(Performance Test)	-	158	-
4(Marking)	-	158	-
7(Design)	-	158	-
8(a) Upper Leather)	-	158	-
8(b) Lining Leather)	-	158	-
8(c) Bottom Material)	-	158	-
8(d) Steel Toe Cap)	-	158	-
8(e) Tape)	-	158	-
8(f) Bottom Filling)	-	158	-
8(g) Eyelet)	-	158	-
8(h) Toe Compound)	-	158	-
8(j) Rivets)	-	158	-
8(k) Screw Wire)	-	158	-
8(m) Shank)	-	158	-
8(n) Laces)	-	158	-
8(o) Tongue Lining)	-	158	-
8(p) Adhesive)	-	158	-
8(q) Strengthening Piece)	-	158	-
8(r) Leather Components)	-	158	-
9(Manufacture)	-	158	-
10(Finish)	-	158	-
11(a) Boots with Leather Sole and Heel)	-	158	-
11(b) Boots with Rubber Sole and Heel)	-	158	-
12(Performance Test)	-	158	-
13(Design)	-	158	-
14(a) Upper Leather)	-	158	-
14(b) Lining Leather)	-	158	-
14(c) Bottom Material)	-	158	-
14(d) Steel Toe Cap)	-	158	-
14(f) Bottom Filling)	-	158	-
14(g) Eyelet)	-	158	-
14(h) Toe Compound)	-	158	-
14(i) Threads)	-	158	-
14(j) Rivets)	-	158	-
14(k) Screw Wire)	-	158	-
14(l) Heel Pin)	-	158	-
14(m) Shank)	-	158	-
14(n) Laces)	-	158	-
14(p) Adhesive)	-	158	-
14(q) Leather Components)	-	158	-
15(Manufacture)	-	158	-
16(Finish)	-	158	-
17(a) Shoes with Leather Sole and Heel)	-	158	-
17(b) Shoes with Rubber Sole and Heel)	-	158	-
7(Design)	-	158	-
8(a) Upper Leather)	-	158	-
8(b) Lining Leather)	-	158	-
8(c) Bottom Material)	-	158	-
8(d) Steel Toe Cap)	-	158	-
8(e) Tape)	-	158	-
8(f) Bottom Filling)	-	158	-
8(g) Eyelet)	-	158	-
8(h) Toe Compound)	-	158	-
8(i) Threads)	-	158	-
8(j) Rivets)	-	158	-
8(k) Screw Wire)	-	158	-
8(l) Heel Pin)	-	158	-
8(m) Shank)	-	158	-
8(n) Laces)	-	158	-
8(o) Tongue Lining)	-	158	-
8(p) Adhesive)	-	158	-
8(q) Strengthening Piece)	-	158	-
8(r) Leather Components)	-	158	-
9(Manufacture)	-	158	-
10(Finish)	-	158	-
11(a) Boots with Leather Sole and Heel)	-	158	-
11(b) Boots with Rubber Sole and Heel)	-	158	-
12(Performance Test)	-	158	-
13(Design)	-	158	-
14(a) Upper Leather)	-	158	-
14(b) Lining Leather)	-	158	-
14(d) Steel Toe Cap)	-	158	-
14(e) Tape)	-	158	-
14(f) Bottom Filling)	-	158	-
14(g) Eyelet)	-	158	-
14(h) Toe Compound)	-	158	-
14(i) Threads)	-	158	-
14(j) Rivets)	-	158	-
14(k) Screw Wire)	-	158	-
14(l) Heel Pin)	-	158	-
14(n) Laces)	-	158	-
14(o) Tongue Lining)	-	158	-
14(p) Adhesive)	-	158	-
14(q) Leather Components)	-	158	-
15(Manufacture)	-	158	-
16(Finish)	-	158	-
17(a) Shoes with Leather Sole and Heel)	-	158	-
17(b) Shoes with Rubber Sole and Heel)	-	158	-
18(Performance Test)	-	158	-

Complete

26 Aug, 2024

IS 11226 (1993)

Leather safety footwear having direct moulded rubber sole specification (First Revision)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(REQUIREMENTS)	-	560	-
5.2(Materials)	-	536	-
5.2.1(Materials)	-	536	-
5.2.1.1(Materials)	-	536	-
5.2.2(Materials)	-	536	-
5.2.3(Materials)	-	536	-
5.2.4(Materials)	-	536	-
5.2.5(Materials)	-	536	-
5.2.6(Materials)	-	536	-
5.2.6.1(Materials)	-	536	-
5.2.6.2(Materials)	-	536	-
5.2.6.3(Materials)	-	536	-
5.2.7(Materials)	-	536	-
5.2.8(Materials)	-	536	-
5.2.9(Materials)	-	536	-
5.2.10(Materials)	-	536	-
5.2.11(Materials)	-	536	-
5.2.11.1(Materials)	-	536	-
5.2.11.2(Materials)	-	536	-
5.2.11.3(Materials)	-	536	-
5.3(Components)	-	536	-
5.4( Manufacture )	-	536	-
5.4.1( Manufacture )	-	536	-
5.4.8(Workmanship and Finish)	-	536	-
5.5(Mass)	-	536	-
5.6(Performance Test)	-	536	-
5.7(Adhesion Test on Moulded Bottoms)	-	536	-
7(MARKING)	-	536	-
5.7(Toe adhesion )	-	536	-
5.5(Mass per pairs)	-	536	-
5.4.8(Leg height)	-	536	-
5.4(Dimension )	-	536	-
5.3 & 5.4.2(Thickness of components )	-	536	-
5.2.11.2(Flexing resistance)	-	536	-
5.2.11.2(Resistance to Fuel Oil)	-	536	-
5.2.11.2(Elongation at break)	-	536	-
5.2.11.2(Tensile Strength)	-	536	-
5.2.11.2(Hardness (Shore A))	-	536	-
5.2.11(Hardness (IRHD)-after ageing)	-	536	-
5.2.11(Relative density )	-	536	-

Complete

26 Aug, 2024

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

ALPHA TEST HOUSE PRIVATE LIMITED

198-199, M.I.E, PHASE-I, BAHADURGARH, HARYANA-124507, Bahadurgarh, Jhajjar, Haryana, 124507

9711227171 info@alphatesthouse.com

Scope List