BIS - LIMS (Laboratory Information Management System)

UL India Private limited, Gurgaon

A-12 Sector 34 Infocity, Gurugram, Gurugram, Haryana, 122001

9560249888 Satish.Kumar@ul.com

Scope List

Reset

29 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

180000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	2000	-
7(Heating under normal operating conditions)	-	17000	-
8(Constructional requirements with regard to the protection against electric shock)	-	8000	-
9(Electric shock hazard under normal operating conditions)	-	18000	-
10(Insulation requirements)	-	24000	-
11(Fault conditions)	-	15000	-
12(Mechanical strength)	-	14000	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	12000	-
15(TERMINALS)	-	8000	-
16(External flexible cords)	-	5000	-
17(Electrical connections and mechanical fixings)	-	5000	-
19(Stability and mechanical hazards)	-	12000	-
20(Resistance to fire)	-	18000	-
3(General requirements)	-	0	-
4(General test conditions)	-	22000	-
Annex-A(Additional requirements for apparatus with protection against splashing water)	-	0	-
Annex-B(Apparatus to be connected to the TELECOMMUNICATION NETWORKS)	-	0	-
Cl.7.1 of Cl.7(General)	-	0	-
Cl.8.1 of Cl.8(Conductive parts covered by lacquer, paper, untreated textile oxide films and beads etc. considered to be bare*)	-	0	-
Cl.8.2 of Cl.8(No shock hazard when changing voltage setting device, fuse-links or handling drawers etc.)	-	0	-
Cl.8.3 of Cl.8(Insulation of hazardous live parts not provided by hygroscopic material)	-	0	-
Cl.8.4 of Cl.8(No risk of electric shock from accessible parts or from parts rendered accessible following the removal of a cover which can be removed by hand)	-	0	-
Cl.8.5 i) of Cl.8(Basic insulation between hazardous live parts and earthed accessible parts *)	-	0	-
Cl.8.5 iv) of Cl.8(Protective earthing terminal *)	-	0	-
Cl.8.6 of Cl.8(Class II apparatus)	-	0	-
Cl.8.8 of Cl.8(Insulation thickness and thin sheet materials)	-	0	-
Cl.8.9 of Cl.8(Adequate insulation between internal hazardous live conductors and accessible parts, or between internal hazardous live parts and conductors connected to accessible parts)	-	0	-
Cl.8.10 of Cl.8(Double insulation between accessible parts and conductors connected to the mains)	-	0	-
Cl.8.10 of Cl.8(Double insulation between conductors connected to accessible parts and parts connected to the mains)	-	0	-
Cl.8.11 of Cl.8(Detaching of wires)	-	0	-
Cl.8.12 of Cl.8(Adequate fastening of windows, lenses, lamp covers etc. (pull test 20 N for 10 s))	-	0	-
Cl.8.13 of Cl.8(Adequate fastening of windows, lenses, lamp covers etc. (pull test 20 N for 10 s))	-	0	-
Cl.8.14 of Cl.8(No risk of damage to the insulation of internal wiring due to hot parts or sharp edges)	-	0	-
Cl.8.15 of Cl.8(Only special supply equipment can be used*)	-	0	-
Cl.8.18 of Cl.8(Disconnection from the mains)	-	0	-
Cl.8.19 of Cl.8(Switch not fitted in the mains cord *)	-	0	-
Cl.8.21 of Cl.8(Non-separable thin sheet material)	-	0	-
Cl.12.1.2 of Cl.12.1(Bump test )	-	0	-
Cl.12.1.3 of Cl.12.1(Vibration test)	-	0	-
Cl.12.1.4 of Cl.12.1(Impact test)	-	0	-
Cl.12.1.5 of Cl.12.1(Drop test)	-	0	-
Cl.12.1.6 of Cl.12.1(Stress relief test)	-	0	-
Cl.12.2 of Cl.12(Fixing of actuating elements)	-	0	-
Cl.12.3 of Cl.12(Remote control devices held in hand)	-	0	-
Cl.12.4 of Cl.12(Drawers )	-	0	-
Cl.12.5 of Cl.12(Antenna coaxial sockets mounted on the apparatus)	-	0	-
Cl.12.6 of Cl.12(Telescoping or rod antennas)	-	0	-
Cl.12.7 of Cl.12(Apparatus containing coin / button cell batteries)	-	0	-
Cl.16.1 a) of Cl.16(Mains supply flexible cords shall be sheathed type, complying with IEC 60227 for PVC cords or as per IEC 60245 for synthetic rubber cords)	-	0	-
Cl.16.2 of Cl.16(Mains cords conductors shall have a nominal cross-sectional area not less than the values given in Table 18, for rated current consumption of the apparatus)	-	0	-
Cl.16.4 of Cl.16(Flexible cords used for connection between equipment have adequate cross-sectional areas to avoid temperature rise under normal and fault conditions)	-	0	-
Cl.16.5 a) of Cl.16(Adequate strain relief on external flexible cords)	-	0	-
Cl.16.6 of Cl.16(Apertures for external flexible cord: no risk of damage to the cord during assembly or movement in use)	-	0	-
Cl.16.7 a) of Cl.16(Transportable apparatus fitted with detachable cord sets with appliance inlet as perIEC60320-1 or)	-	0	-
Cl.19.2 of Cl.19(Test at 10° to the horizontal)	-	0	-
Cl.19.3 of Cl.19(Vertical force test )	-	0	-
Cl.19.4 of Cl.19(Horizontal force test)	-	0	-
Cl.19.5 of Cl.19(Test of edges and corners)	-	0	-
Cl.19.6 of Cl.19(Mechanical strength of glass)	-	0	-
Cl.19.7 of Cl.19(Wall or ceiling mounting means)	-	0	-
3(General requirements)	-	0	-
4(General test conditions)	-	0	-
5(Marking and instructions)	-	0	-
Cl.7.1 of Cl.7(General)	-	0	-
8(Constructional requirements with regard to the protection against electric shock)	-	0	-
9(Electric shock hazard under normal operating conditions)	-	0	-
10(Insulation requirements)	-	0	-
11(Fault conditions)	-	0	-
12(Mechanical strength)	-	0	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	0	-
15(TERMINALS)	-	0	-
16(External flexible cords)	-	0	-
17(Electrical connections and mechanical fixings)	-	0	-
19(Stability and mechanical hazards)	-	0	-
20(Resistance to fire)	-	0	-
Annex-A(Additional requirements for apparatus with protection against splashing water)	-	0	-
Annex-B(Apparatus to be connected to the TELECOMMUNICATION NETWORKS)	-	0	-
3(General requirements)	-	0	-
4(General test conditions)	-	0	-
5(Marking and instructions)	-	0	-
Cl.7.1 of Cl.7(General)	-	0	-
8(Constructional requirements with regard to the protection against electric shock)	-	0	-
9(Electric shock hazard under normal operating conditions)	-	0	-
10(Insulation requirements)	-	0	-
11(Fault conditions)	-	0	-
12(Mechanical strength)	-	0	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	0	-
15(TERMINALS)	-	0	-
16(External flexible cords)	-	0	-
17(Electrical connections and mechanical fixings)	-	0	-
19(Stability and mechanical hazards)	-	0	-
20(Resistance to fire)	-	0	-
Annex-A(Additional requirements for apparatus with protection against splashing water)	-	0	-
Annex-B(Apparatus to be connected to the TELECOMMUNICATION NETWORKS)	-	0	-
3(General requirements)	-	0	-
4(General test conditions)	-	0	-
5(Marking and instructions)	-	0	-
7(Heating under normal operating conditions)	-	0	-
8(Constructional requirements with regard to the protection against electric shock)	-	0	-
9(Electric shock hazard under normal operating conditions)	-	0	-
10(Insulation requirements)	-	0	-
11(Fault conditions)	-	0	-
12(Mechanical strength)	-	0	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	0	-
15(TERMINALS)	-	0	-
16(External flexible cords)	-	0	-
17(Electrical connections and mechanical fixings)	-	0	-
19(Stability and mechanical hazards)	-	0	-
20(Resistance to fire)	-	0	-
15(Internal wires and power cords)	-	0	-
Annex-A(Additional requirements for apparatus with protection against splashing water)	-	0	-
Annex-B(Apparatus to be connected to the TELECOMMUNICATION NETWORKS)	-	0	-
Cl.5.1 of Cl.5(General requirements)	-	0	-
Cl.5.1-i) of Cl.5(Comprehensible and easily discernible)	-	0	-
Cl.5.1-ii) of Cl.5(Permanent durability against water and petroleum spirit)	-	0	-
Cl.5.2 of Cl.5(Identification and supply ratings)	-	0	-
Cl.5.2 a) of Cl.5(Identification, maker)	-	0	-
Cl.5.2 b) of Cl.5(Model number or type reference)	-	0	-
Cl.5.2 d) of Cl.5(Nature of supply)	-	0	-
Cl.5.2 e) of Cl.5(Rated supply voltage)	-	0	-
Cl.5.2 f) of Cl.5(Mains frequency if safety dependant)	-	0	-
Cl.5.2 g) of Cl.5(Rated current or power consumption for apparatus supplied by supply apparatus for general use, on apparatus or in instruction manual: Measured current or power consumption: Deviation % (max 10%):)	-	0	-
Cl.5.2 h) of Cl.5(Rated current or power consumption for apparatus intended for connection to an a.c. mains supply:Measured current or power consumption for Television set: Deviation % (max 10%):)	-	0	-
Cl.5.2 h)-i) of Cl.5(appliance coupler for Class I is used for Class II equipment with functional earth connection, the requirements of Clause 15 and Clause 16 related to Class I construction shall be applied up to the connecting point of the protective(earthing) conductor to the functional earth.)	-	0	-
Cl.5.2 h)-ii) of Cl.5(Graphical symbols placed on the apparatus, whether required by this standard or not, shall be in accordance with IEC 60417 or ISO 3864-2 or ISO 7000, if available. In the absence of suitable symbols, the manufacturer may design specific graphical symbols.)	-	0	-
Cl.5.2 h)-iii) of Cl.5(Care shall be taken so that additional markings and instructions not required by this standard do not contradict the markings and instructions required by this standard . Symbols placed on the Equipment shall be explained in the user manual.)	-	0	-
Cl.5.3 of Cl.5(Terminals)	-	0	-
Cl.5.3a) of Cl.5(Earth terminal)	-	0	-
Cl.5.3b) of Cl.5(Hazardous live terminals)	-	0	-
Cl.5.3c) of Cl.5(Markings on supply output terminals)	-	0	-
Cl.5.4 of Cl.5(Caution marking)	-	0	-
Cl.5.4a) of Cl.5(Use of triangle with exclamation mark)	-	0	-
Cl.5.4b) of Cl.5(Marking on loudspeaker grille, IEC 60417-5036)	-	0	-
Cl.5.4c) of Cl.5(User-replaceable coin / button cell battery marking)	-	0	-
Cl.5.5 of Cl.5(Instructions)	-	0	-
Cl.5.5 of Cl.5(Instructions)	-	0	-
Cl.5.5 of Cl.5(Instructions)	-	0	-
Cl.5.5.1 of Cl.5.5(Safety relevant information)	-	0	-
Cl.5.5.2 a) of Cl.5.5(Mains powered equipment not exposed to dripping or splashing. Warning concerning objects filled with liquid, etc.)	-	0	-
Cl.5.5.2 b) of Cl.5.5(Hazardous live terminals, instructions for wiring)	-	0	-
Cl.5.5.2 c) of Cl.5.5(Instructions for replacing lithium battery)	-	0	-
Cl.5.5.2 d) of Cl.5.5(Class I earth connection warning)	-	0	-
Cl.5.5.2 e) of Cl.5.5(Instructions for multimedia system connection)	-	0	-
Cl.5.5.2 f) of Cl.5.5(Special stability warning for attachment of the apparatus to the floor/wall)	-	0	-
Cl.5.5.2 g) of Cl.5.5(Warning: battery exposure to heat)	-	0	-
Cl.5.5.2 h) of Cl.5.5(Warning: protective film on CRT face)	-	0	-
Cl.5.5.2 i) of Cl.5.5("Warning: Non-floor standing TV >7kg")	-	0	-
Cl.5.5.2 j) of Cl.5.5("Warning: User replaceable coin / button cell battery")	-	0	-
Cl.5.5.3 (a-b) of Cl.5.5(Disconnect device: plug/coupler or all-pole mains switch location, accessibility and markings)	-	0	-
Cl.5.5.3 c) of Cl.5.5(Instructions for permanently connected equipment)	-	0	-
Cl.5.5.3 c) i) of Cl.5.5(Marking, signal lamps or similar for completely disconnection from the mains)	-	0	-
Cl.7.1 of Cl.7(General)	-	0	-
"Cl.7.1.1 of Cl.7.1 Table-3"(Requirements)	-	0	-
"Cl.7.1.2 of Cl.7.1 Table-3"(Accessible parts)	-	0	-
"Cl.7.1.3 of Cl.7.1 Table-3"(Parts, other than windings and printed boards, providing electrical insulation)	-	0	-
"Cl.7.1.4 of Cl.7.1 Table-3"(Parts acting as a support or a mechanical barrier)	-	0	-
"Cl.7.1.5 of Cl.7.1 Table-3"(Windings)	-	0	-
"Cl.7.1.6 of Cl.7.1 Table-3"(Parts not subject to a limit under7.1.1 to 7.1.4)	-	0	-
Cl.8.1 of Cl.8(Conductive parts covered by lacquer, paper, untreated textile oxide films and beads etc. considered to be bare*)	-	0	-
Cl.8.2 of Cl.8(No shock hazard when changing voltage setting device, fuse-links or handling drawers etc.)	-	0	-
Cl.8.3 of Cl.8(Insulation of hazardous live parts not provided by hygroscopic material)	-	0	-
Cl.8.4 of Cl.8(No risk of electric shock from accessible parts or from parts rendered accessible following the removal of a cover which can be removed by hand)	-	0	-
Cl.8.5 of Cl.8(Class I apparatus*)	-	0	-
Cl.8.5 i) of Cl.8(Basic insulation between hazardous live parts and earthed accessible parts *)	-	0	-
Cl.8.5 iv) of Cl.8(Protective earthing terminal *)	-	0	-
Cl.8.6 of Cl.8(Class II apparatus)	-	0	-
Cl.8.6 a) of Cl.8(Basic and supplementary insulation between hazardous live parts and accessible parts *)	-	0	-
Cl.8.6 b) of Cl.8(Reinforced insulation between hazardous live parts and accessible parts *)	-	0	-
Cl.8.8 of Cl.8(Insulation thickness and thin sheet materials)	-	0	-
Cl.8.8 i) of Cl.8(Basic or supplementary insulation > 0,4 mm (mm)*)	-	0	-
Cl.8.8 ii) of Cl.8(Reinforced insulation > 0,4 mm (mm) *)	-	0	-
Cl.8.8 iii) of Cl.8(Thin sheet material used inside the equipment)	-	0	-
Cl.8.8 iv) of Cl.8(Basic or supplementary insulation, atleast two layers, each meeting10.4)	-	0	-
Cl.8.8 v) of Cl.8(Basic or supplementary insulation, three layers any two of which meet10.4)	-	0	-
Cl.8.8 vi) of Cl.8(Reinforced insulation, two layers each of which meet 10.4)	-	0	-
Cl.8.9 of Cl.8(Adequate insulation between internal hazardous live conductors and accessible parts, or between internal hazardous live parts and conductors connected to accessible parts)	-	0	-
Cl.8.10 of Cl.8(Double insulation between accessible parts and conductors connected to the mains)	-	0	-
Cl.8.10 of Cl.8(Double insulation between conductors connected to accessible parts and parts connected to the mains)	-	0	-
Cl.8.11 of Cl.8(Detaching of wires)	-	0	-
Cl.8.11 i) of Cl.8(Noun due reduction of creepage or clearance distances if wires become detached)	-	0	-
Cl.8.11 ii) of Cl.8(Vibration test carried out)	-	0	-
Cl.8.12 of Cl.8(Adequate fastening of windows, lenses, lamp covers etc. (pull test 20 N for 10 s))	-	0	-
Cl.8.13 of Cl.8(Adequate fastening of windows, lenses, lamp covers etc. (pull test 20 N for 10 s))	-	0	-
Cl.8.14 of Cl.8(No risk of damage to the insulation of internal wiring due to hot parts or sharp edges)	-	0	-
Cl.8.15 of Cl.8(Only special supply equipment can be used*)	-	0	-
Cl.8.18 of Cl.8(Disconnection from the mains)	-	0	-
Cl.8.18 i) of Cl.8(Disconnect device used in apparatus)	-	0	-
Cl.8.18 ii) of Cl.8(All-pole switch or circuit breaker with >3mm contact separation.)	-	0	-
Cl.8.18 iii) of Cl.8(Mains switch ON indication *)	-	0	-
Cl.8.19 of Cl.8(Switch not fitted in the mains cord *)	-	0	-
Cl.8.21 of Cl.8(Non-separable thin sheet material)	-	0	-
Cl.9.1 of Cl.9(Testing on the outside)	-	0	-
Cl.9.1.1 of Cl.9.1(Requirements)	-	0	-
Cl.9.1.1 i) of Cl.9.1(Accessible parts shall not be hazardous live)	-	0	-
Cl.9.1.1 ii) of Cl.9.1(Inaccessible terminals are not accessible or comply with relevant requirements)	-	0	-
Cl.9.1.1 iii) of Cl.9.1(For voltages >1000 V ac or >1500 V dc complies with clause 13.3.1 for basic insulation)	-	0	-
Cl.9.1.1.2 of Cl.9.1.1(Determination of hazardous live parts)	-	0	-
Cl.9.1.1.2 a) of Cl.9.1.1(Open circuit voltages)	-	0	-
Touch current measured from terminal devices using the network in annex D(Touch current measured from terminal devices using the network in annex D)	-	0	-
Cl.9.1.1.2 c) of Cl.9.1.1(The charge exceeds 45 μC)	-	0	-
Cl.9.1.1.2 d) of Cl.9.1.1(Energy of discharge not exceeding 350 mJ)	-	0	-
Cl.9.1.1.3 of Cl.9.1.1(Test with test finger and test probe)	-	0	-
Cl.9.1.2 of Cl.9.1(Shafts of operating knobs, handles, levers and the like)	-	0	-
Cl.9.1.3 of Cl.9.1(Openings ofthe enclosure)	-	0	-
Cl.9.1.4 of Cl.9.1(Terminals)	-	0	-
Cl.9.1.4 i) of Cl.9.1(Terminals)	-	0	-
Cl.9.1.4 ii) of Cl.9.1(Terminals)	-	0	-
Cl.9.1.5 of Cl.9.1(Pre-set controls)	-	0	-
Cl.9.1.6 of Cl.9.1(Withdrawal of the mains plug:)	-	0	-
Cl.9.1.6 i) of Cl.9.1(Withdrawal of the mains plug:)	-	0	-
Cl.9.1.6 ii) of Cl.9.1(Withdrawal of the mains plug:)	-	0	-
Cl.9.1.6 iii) of Cl.9.1(Withdrawal of the mains plug:)	-	0	-
Cl.9.1.7 of Cl.9.1(Resistance to external forces)	-	0	-
Cl.9.1.7 a) of Cl.9.1(Resistance to external forces)	-	0	-
Cl.9.1.7 b) of Cl.9.1(Resistance to external forces)	-	0	-
Cl.9.1.7 c) of Cl.9.1(Resistance to external forces)	-	0	-
Cl.9.2 of Cl.9(Removal of protective covers)	-	0	-
Cl.10.2 of Cl.10(Surge Test)	-	0	-
Cl.10.2 a) of Cl.10(Surge Test)	-	0	-
Cl.10.2 b) of Cl.10(Surge Test)	-	0	-
Cl.10.2 b) (i) of Cl.10(Surge Test)	-	0	-
Cl.10.2 b) (ii) of Cl.10(Surge Test)	-	0	-
Cl.10.2 b) (iii) of Cl.10(Surge Test)	-	0	-
Cl.10.3 of Cl.10(Humidity treatment)	-	0	-
Cl.10.4 of Cl.10(Insulation resistance and dielectric strength)	-	0	-
Cl.10.4.1 of Cl.10.4(Insulation of the insulating materials)	-	0	-
Cl.10.4.2 of Cl.10.4(Between parts of different polarity directly connected to the mains Between parts of different polarity directly connected to the mains)	-	0	-
Cl.10.4.2 i) of Cl.10.4(Between parts separated by BASIC or SUPPLEMENTARY insulation)	-	0	-
Cl.10.4.2 ii) of Cl.10.4(Between parts separated by REINFORCED insulation)	-	0	-
Cl.11.1 of Cl.11(Electric Shock Hazard)	-	0	-
Cl.11.1 a) of Cl.11(Electric Shock Hazard)	-	0	-
Cl.11.1 b) of Cl.11(Electric Shock Hazard)	-	0	-
Cl.11.2 of Cl.11(Heating)	-	0	-
Cl.11.2.1 of Cl.11.2(Requirements)	-	0	-
Cl.11.2.1 i) of Cl.11.2(No danger of fire to the surroundings)	-	0	-
Cl.11.2.1 ii) of Cl.11.2(Safety not impaired by abnormal heat)	-	0	-
Cl.11.2.1 of Cl.11.2(Flames extinguish within 10 seconds)	-	0	-
Cl.11.2.1 of Cl.11.2(No hazard from softening solder)	-	0	-
Cl.11.2.1 of Cl.11.2(Soldered terminations not used as protective mechanism)	-	0	-
Cl.11.2.2 of Cl.11.2(Measurement of temperature rises)	-	0	-
Cl.11.2.3 of Cl.11.2(Accessible parts)	-	0	-
Cl.11.2.4 of Cl.11.2(Parts, other than windings and printed boards, providing electrical insulation)	-	0	-
Cl.11.2.5 of Cl.11.2(Parts acting as a support or a mechanical barrier)	-	0	-
Cl.11.2.6 of Cl.11.2(Windings )	-	0	-
Cl.11.2.7 of Cl.11.2(Printed boards)	-	0	-
Cl.11.2.7 i) of Cl.11.2(Printed boards)	-	0	-
Cl.11.2.7 i) a) of Cl.11.2(Printed boards)	-	0	-
Cl.11.2.7 i) b) of Cl.11.2(Printed boards)	-	0	-
Cl.11.2.7 ii) of Cl.11.2(Printed boards)	-	0	-
Cl.11.2.7 iii) of Cl.11.2(Printed boards)	-	0	-
Cl.11.2.8 of Cl.11.2(Parts not subject to a limit under7.1.1 to 7.1.4)	-	0	-
Cl.12.1.1 of Cl.12.1(Requirements)	-	0	-
Cl.12.1.2 of Cl.12.1(Bump test )	-	0	-
Cl.12.1.3 of Cl.12.1(Vibration test)	-	0	-
Cl.12.1.4 of Cl.12.1(Impact test)	-	0	-
Cl.12.1.4 i) of Cl.12.1(Impact test)	-	0	-
Cl.12.1.4 ii) of Cl.12.1(Impact test)	-	0	-
Cl.12.1.5 of Cl.12.1(Drop test)	-	0	-
Cl.12.1.6 of Cl.12.1(Stress relief test)	-	0	-
Cl.12.2 of Cl.12(Fixing of actuating elements)	-	0	-
Cl.12.3 of Cl.12(Remote control devices held in hand)	-	0	-
Cl.12.4 of Cl.12(Drawers )	-	0	-
Cl.12.5 of Cl.12(Antenna coaxial sockets mounted on the apparatus)	-	0	-
Cl.12.5 a) of Cl.12(Endurance test,)	-	0	-
Cl.12.5 b) of Cl.12(Impact test,)	-	0	-
Cl.12.5 c) of Cl.12(Torque test)	-	0	-
Cl.12.6 of Cl.12(Telescoping or rod antennas)	-	0	-
Cl.12.6.1 of Cl.12.6(General requirements)	-	0	-
Cl.12.6.1 i) of Cl.12.6(General requirements)	-	0	-
Cl.12.6.2 of Cl.12.6(Physical securement)	-	0	-
Cl.12.7 of Cl.12(Apparatus containing coin / button cell batteries)	-	0	-
Cl.12.7.1 of Cl.12.7(Coin/button cell batteries with a diameter of 32 mm or less.)	-	0	-
Cl.12.7.2 of Cl.12.7(Construction requirementss)	-	0	-
Cl.12.7.3 of Cl.12.7(Tests)	-	0	-
Cl.12.7.3.2 of Cl.12.7.3(Stress relief test)	-	0	-
Cl.12.7.3.3 of Cl.12.7.3(Battery replacement test)	-	0	-
Cl.12.7.3.4 of Cl.12.7.3(Drop test)	-	0	-
Cl.12.7.3.5 of Cl.12.7.3(Impact test)	-	0	-
Cl.12.7.3.6 of Cl.12.7.3(Crush test)	-	0	-
Cl.12.7.4 of Cl.12.7(Compliance)	-	0	-
Cl.13.1 of Cl.13(General)	-	0	-
Cl.13.2 of Cl.13(Determination of Working voltage)	-	0	-
Cl.13.3 of Cl.13(Clearances)	-	0	-
Cl.13.3.1 of Cl.13.3(General)	-	0	-
Cl.13.3.2 of Cl.13.3(Clearances in circuits conductively connected to the mains)	-	0	-
Cl.13.3.3 of Cl.13.3(Clearances in circuits not conductively connected to the mains)	-	0	-
Cl.13.3.4 of Cl.13(Measurement of transient voltages)	-	0	-
Cl.13.4 a) of Cl.13(Creepage distances )	-	0	-
Cl.13.4 b) of Cl.13(Creepage distances )	-	0	-
Cl.13.4 c) of Cl.13(Creepage distances )	-	0	-
Cl.13.6 a) of Cl.13(Jointed insulation )	-	0	-
Cl.13.6 b) of Cl.13(Jointed insulation )	-	0	-
Cl.13.6 c) of Cl.13(Jointed insulation )	-	0	-
Cl.13.6 d) of Cl.13(Jointed insulation )	-	0	-
Cl.13.7 of Cl.13(Enclosed and sealed parts)	-	0	-
Cl.13.8 of Cl.13(Parts filled with insulating compound, meeting the requirements of 8.8)	-	0	-
Cl.15.1 of Cl.15(Plugs and Sockets*)	-	0	-
Cl.15.1.2 of Cl.15.1(Design of connectors other than for mains power *)	-	0	-
Cl.15.1.2 i) of Cl.15.1(Design of sockets with symbol of 5.3 b) design *)	-	0	-
Cl.15.1.3 of Cl.15.1(Design of terminals and connectors used in output circuits of supply apparatus*)	-	0	-
Cl.15.2 of Cl.15(Provisions for protective earthing)	-	0	-
Cl.15.2 i) of Cl.15(Provisions for protective earthing)	-	0	-
Cl.15.2 ii) of Cl.15(Provisions for protective earthing)	-	0	-
Cl.15.2 iii) of Cl.15(Provisions for protective earthing)	-	0	-
Cl.15.2 iv) of Cl.15(Provisions for protective earthing)	-	0	-
Cl.15.2 v) of Cl.15(Provisions for protective earthing)	-	0	-
Cl.15.3 of Cl.15(Terminals for external flexible cords and for permanent connection to the mains supply*)	-	0	-
Cl.15.3.1 of Cl.15.3(Adequate terminals for connection of permanent wiring*)	-	0	-
Cl.15.3.2 of Cl.15.3(Reliable connection of non-detachable cords)	-	0	-
Cl.15.3.2 i) of Cl.15.3(Not soldered to conductors of a printed circuit board)	-	0	-
Cl.15.3.2 ii) of Cl.15.3(Adequate clearances and creepage distances between connections should a wire break away)	-	0	-
Cl.15.3.2 iii) of Cl.15.3(Wire secured by additional means to the conductor)	-	0	-
Cl.15.3.3 of Cl.15.3(Screws and nuts clamping conductors have adequate threads: ISO 261, ISO 262 or similar*)	-	0	-
Cl.15.3.4 of Cl.15.3(Conductors adequately fixed (two independent fixings) *)	-	0	-
Cl.15.3.5 of Cl.15.3(Terminals allow connection of conductors having appropriate cross-sectional area)	-	0	-
Cl.15.3.6 of Cl.15.3(Terminals to 15.3.3 have sizes required by table 16)	-	0	-
Cl.15.3.7 of Cl.15.3(Terminals clamp conductors between metal and have adequate pressure)	-	0	-
Cl.15.3.7 i) of Cl.15.3(Terminals designed to avoid conductor slipping out when tightened)	-	0	-
Cl.15.3.7 ii) of Cl.15.3(Terminals adequately fixed when tightened or loosened (no loosening, wiring not stressed, distances not reduced))	-	0	-
Cl.15.3.8 of Cl.15.3(Terminals carrying a current more than)	-	0	-
Cl.15.3.8 i) of Cl.15.3(0.2 A, contact pressure not transmitted by insulating material except ceramic*)	-	0	-
Cl.15.3.9 of Cl.15.3(Termination of non-detachable cords: wires terminated near to each other)	-	0	-
Cl.15.3.9 i) of Cl.15.3(Terminals located and shielded: test with 8 mm strand)	-	0	-
Cl.15.4 of Cl.15(Devices forming a part of the mains plug*)	-	0	-
Cl.15.4.1 of Cl.15.4(No undue strain on mains socket-outlets.)	-	0	-
Cl.15.4.1 i) of Cl.15.4(Device shall be tested on the equipment as per Fig.11: Torque to be applied : 0.25 Nm (Max))	-	0	-
Cl.15.4.2 of Cl.15.4(Device complies with standard for dimensions of mains plugs)	-	0	-
Cl.15.4.3 of Cl.15.4(Device has adequate mechanical strength (tests a,b,c))	-	0	-
Cl.16.1 a) of Cl.16(Mains supply flexible cords shall be sheathed type, complying with IEC 60227 for PVC cords or as per IEC 60245 for synthetic rubber cords)	-	0	-
Cl.16.1 b) of Cl.16(Non-detachable cords for Class I have green/yellow core for protective earth)	-	0	-
Cl.16.2 of Cl.16(Mains cords conductors shall have a nominal cross-sectional area not less than the values given in Table 18, for rated current consumption of the apparatus)	-	0	-
Cl.16.4 of Cl.16(Flexible cords used for connection between equipment have adequate cross-sectional areas to avoid temperature rise under normal and fault conditions)	-	0	-
Cl.16.5 a) of Cl.16(Adequate strain relief on external flexible cords)	-	0	-
Cl.16.5 b) of Cl.16(Not possible to push cord back into equipment)	-	0	-
Cl.16.5 c) of Cl.16(Strain relief device unlikely to damage flexible cord)	-	0	-
Cl.16.5 d) of Cl.16(For mains cords of Class I equipment, hazardous live conductors become taut before earth conductor)	-	0	-
Cl.16.6 of Cl.16(Apertures for external flexible cord: no risk of damage to the cord during assembly or movement in use)	-	0	-
Cl.16.7 a) of Cl.16(Transportable apparatus fitted with detachable cord sets with appliance inlet as perIEC60320-1 or)	-	0	-
Cl.16.7 b) of Cl.16(Transportable apparatus shall have a means of stowage to protect the cord)	-	0	-
17.1 a) of Cl.17(Screws are loosened and then tightened with a torque according to table20)	-	0	-
Cl.17.1 b) of Cl.17(5 times in the case of screws operating in a thread of metal)	-	0	-
Cl.17.1 c) of Cl.17(10 times in the case of screws operating in wood or in a thread in insulating material:)	-	0	-
Cl.17.2 of Cl.17(Correct introduction of screws into female threads in non-metallic material)	-	0	-
Cl.17.3 a) of Cl.17(Screws or other fixing devices intended to fix Covers, legs, stands or the like, shall be captive in order to prevent replacement during servicing by screws or other fixing devices……)	-	0	-
Cl.17.3 b) of Cl.17(Non-captive fixing screws: no hazard when replaced by a screw whose length is 10 times its diameter)	-	0	-
Cl.17.4 of Cl.17(No loosening of conductive parts carrying a current > 0.2 A)	-	0	-
Cl.17.5 of Cl.17(Contact pressure not transmitted through plastic other than ceramic for connections carrying a current > 0.2 A*)	-	0	-
Cl.17.6 of Cl.17(Stranded conductors of flexible supply cords carrying a current > 0.2 A with screw terminals not consolidated by solder *)	-	0	-
Cl.17.7 of Cl.17(Cover fixing devices other than screws have adequate strength and their positioning is unambiguous)	-	0	-
Cl.17.8 of Cl.17(Detachable legs or stands supplied by the manufacturer of the apparatus shall be delivered with the relevant fixing means *)	-	0	-
Cl.17.9 a) of Cl.17(Internal pluggable connections, affecting safety, unlikely to become disconnected)	-	0	-
Cl.17.9 b) of Cl.17(By applying a 2N pull force in any direction to the connection, in case of doubt)	-	0	-
Cl.19.1 of Cl.19(Stability and mechanical hazards)	-	0	-
Cl.19.1 of Cl.19(Stability requirements)	-	0	-
Cl.19.1 i) of Cl.19(Stability requirements)	-	0	-
Cl.19.2 of Cl.19(Test at 10° to the horizontal)	-	0	-
Cl.19.3 of Cl.19(Vertical force test )	-	0	-
Cl.19.4 of Cl.19(Horizontal force test)	-	0	-
Cl.19.5 of Cl.19(Test of edges and corners)	-	0	-
Cl.19.6 of Cl.19(Mechanical strength of glass)	-	0	-
Cl.19.6.1 of Cl.19.6(Requirements)	-	0	-
Cl.19.6.2 of Cl.19.6(Fragmentation test)	-	0	-
Cl.19.7 of Cl.19(Wall or ceiling mounting means)	-	0	-
Cl.19.7.1 of Cl.19..7(Requirements)	-	0	-
Cl.19.7.3 of Cl.19.7(Compliance)	-	0	-
Cl.20.1 of Cl.20(Requirements)	-	0	-
Cl.20.2 of Cl.20(Electrical components and mechanical parts)	-	0	-
Cl.20.2.1 a) of Cl.20.2(Exemption for components contained in an enclosure of material V-0 to IEC60695- 11-10 with openings not exceeding 1 mm in width)	-	0	-
Cl.20.2.1 b) of Cl.20.2(Exemption for small components)	-	0	-
Cl.20.2.2 of Cl.20.2(Electrical components )	-	0	-
Cl.20.2.3 of Cl.20.2(Internal wiring)	-	0	-
Cl.20.2.5 of Cl.20.2(Components and parts not covered by 20.2.2, 20.2.3 and 20.2.4)	-	0	-
Cl.20.2.5 i) of Cl.20.2(Components and parts not covered by 20.2.2, 20.2.3 and 20.2.4)	-	0	-
Cl.20.2.5 ii) of Cl.20.2(Components and parts not covered by 20.2.2, 20.2.3 and 20.2.4)	-	0	-
Cl.20.3 of Cl.20(Fire enclosure*)	-	0	-
Cl.20.3.1 of Cl.20.3(Fire enclosure*)	-	0	-
Cl.20.3.2 of Cl.20.3(Fire enclosure*)	-	0	-
Cl.20.3.3 of Cl.20.3(Fire enclosure*)	-	0	-

Complete

07 Aug, 2028

-
Included w.e.f. 14-12-2023 Exclusion: Cl.6 (Hazardous radiations), Cl. 6.1 (Ionizing radiation), Cl. 6.2 (Laser Radiation),Cl.7.2 of Cl.7 (Softening temperature of insulating material supporting parts conductively connected to the mains carrying a current> 0.2 A, shall be at least 150ºC), Cl.8.5 ii) of Cl.8 (Resistors bridging basic insulation shall complying with 14.1 a) *), Cl.8.5 iii) of Cl.8 (Capacitors bridging basic insulation shall complying with 14.2.1 a) *), Cl.8.7 of Cl.8 (Components bridging insulation), Cl.8.7 i) of Cl.8 (Basic insulation bridged by components complying with 14.4.5.3), Cl.8.7 ii) of Cl.8 (Components bridging basic, supplementary, double or reinforced insulation complying with 14.2 a) or 14.4), Cl.8.7 iii) of Cl.8 (Basic and supplementary insulation each being bridged by a capacitor or RC-unit complying with 14.3.2 a)), Cl.8.7 iv) of Cl.8 (Double or reinforced insulation being bridged with 2 capacitors or RC-units in series complying with 14.3.2 a)), Cl.8.7 v) of Cl.8 (Double or reinforced insulation being bridged with a single capacitor or RC-unit complying with 14.3.2 b)), Cl.8.16 of Cl.8 (Insulated winding wire without additional interleaved insulation), Cl.8.16/ H 2.2/ H 2.3 , Cl.8.20 of Cl.8 (Bridging components comply with clause 14), 14 (Components), Cl. Cl.15.1.1 i), ii) of Cl.15.1 (Plugs and Sockets*), Cl.16.3 a) of Cl.16 (Flexiblecordsnotcomplyingwith16.1, used for interconnections between separate units of equipment used in combination and carrying hazardous live voltages, have adequate dielectric strength as perCl.10.3), 16.3b (Cord Bending Test), Cl. 18 (Mechanical strength of picture tubes and protection against the effects of implosion), Cl.20.2.4 i) of Cl.20.2 (Printed boards), Annex-L (Additional requirements for electronic flash apparatus for photographic purposes), Cl6.3 (LED)

IS 16333 : Part 3 (2022)

Mobile phone handsets: Part 3 Indian language support for mobile phone handsets - Specific requirements(Second Revision)

31350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Inputting of text)	-	15000	NA
5.2(Message Readability)	-	15000	NA
6(Marking)	-	1350	NA
5.1(Inputting of text)	-	-	-
5.2(Message Readability)	-	-	-
6(Marking)	-	-	-

Complete

07 Aug, 2028

-
-

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

14700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Marking- IS 302-1)	-	100	NA
7.14(Marking- IS 302-1)	-	100	NA
8( Protection Against Electric Shock, IS 302-1)	-	750	NA
10(Power Input and Current, IS 302-1)	-	1000	NA
11(Heating, IS 302-1)	-	1000	NA
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	200	NA
14(Transient Over Voltages, IS 302-1)	-	1000	NA
15(Moisture Resistance, IS 302-1)	-	1350	NA
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	200	NA
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	500	NA
16(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	300	NA
19.7(Abnormal Operation, IS 302-1)	-	100	NA
19.8(Abnormal Operation, IS 302-1)	-	100	NA
19.9(Abnormal Operation, IS 302-1)	-	100	NA
19.101(Abnormal Operation)	-	100	NA
19.102(Abnormal Operation)	-	100	NA
13(Electrical Insulation and Leakage Current at Operating Temperature: High Voltage, IS 302-1)	-	200	NA
20.1(Stability & Mechanical Hazards, IS 302-1)	-	50	NA
19.1(Abnormal Operation, IS 302-1)	-	100.00	NA
20.2(Stability & Mechanical Hazards, IS 302-1)	-	50	NA
20.101(Stability & Mechanical Hazards)	-	50	NA
20.102(Stability & Mechanical Hazards)	-	50	NA
20.103(Stability & Mechanical Hazards)	-	50	NA
20.104(Stability & Mechanical Hazards)	-	50	NA
20.105(Stability & Mechanical Hazards)	-	50	NA
20.106(Stability & Mechanical Hazards)	-	50	NA
20.107(Stability & Mechanical Hazards)	-	50	NA
20.108(Stability & Mechanical Hazards)	-	50	NA
20.109(Stability & Mechanical Hazards)	-	50	NA
20.111(Stability & Mechanical Hazards)	-	50	NA
20.112(Stability & Mechanical Hazards)	-	50	NA
20.113(Stability & Mechanical Hazards)	-	50	NA
20.114(Stability & Mechanical Hazards)	-	50	NA
20.115(Stability & Mechanical Hazards)	-	50	NA
20.116(Stability & Mechanical Hazards)	-	50	NA
21.1(Mechanical Strength, IS 302-1)	-	500	NA
21.2(Mechanical Strength, IS 302-1)	-	500	NA
22(Construction, IS 302-1)	-	500	NA
22.101(Construction)	-	500	NA
22.102(Construction)	-	500	NA
23.1(Internal Wiring, IS 302-1)	-	50	NA
23.2(Internal Wiring, IS 302-1)	-	50	NA
23.3(Internal Wiring, IS 302-1)	-	50	NA
23.4(Internal Wiring, IS 302-1)	-	50	NA
23.5(Internal Wiring, IS 302-1)	-	50	NA
23.6(Internal Wiring, IS 302-1)	-	50	NA
23.7(Internal Wiring, IS 302-1)	-	50	NA
23.8(Internal Wiring, IS 302-1)	-	50	NA
23.9(Internal Wiring, IS 302-1)	-	50	NA
23.10(Internal Wiring, IS 302-1)	-	50	NA
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	50	NA
26(Terminals for External Conductors, IS 302-1)	-	200	NA
27(Provision for Earthing, IS 302-1)	-	100	NA
27.2(Provision for Earthing, IS 302-1)	-	100	NA
27.3(Provision for Earthing, IS 302-1)	-	100	NA
27.4(Provision for Earthing, IS 302-1)	-	100	NA
27.5(Provision for Earthing, IS 302-1)	-	100	NA
28(Screws & Connections, IS 302-1)	-	500	NA
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	300	NA
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	300	NA
30.1(Resistance to Heat and Fire, IS 302-1)	-	400	NA
30.2(Resistance to Heat and Fire, IS 302-1)	-	400	NA

Complete

07 Aug, 2028

-
Exclusions: EMI/EMC (Electrostatic, Discharges, Radiant fields, Fast transient bursts, Voltage surges, Injected current, Voltage dips & Interruptions, Mains signals) (Cl.19.11.4.1 to Cl.19.11.4.1), Component (Cl.24)

IS 302 : Part 2 : Sec 6 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 6 cooking ranges, hobs, ovens and similar appliances (First Revision)

19635 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Marking and instructions)	-	500	NA
8.0(Protection against access to live part test)	-	500	NA
10.0(Power Input and current test)	-	1135	NA
11.0(Heating test)	-	500	NA
13.0(Leakage current and electric strength test)	-	500	NA
14.0(Transient voltages)	-	500	NA
15.0(Moisture Resistance)	-	500	NA
16.0(Leakage current and electric strength test)	-	500	NA
17.0(Overload protection of transformers test)	-	500	NA
18.0(Endurance test)	-	500	NA
19.0(Abnormal Operations)	-	500	NA
20.0(Stability and Mechanical Hazards)	-	300	NA
21.0(Mechanical Strength)	-	200	NA
22.0(Construction verification related tests)	-	500	NA
23.0(Internal wiring)	-	500	NA
25.0(Supply connections and External Flexible Cords)	-	500	NA
26.0(Terminal for External Conductors)	-	500	NA
27.0(Provision for Earthing)	-	500	NA
28.0(Screws and connections)	-	500	NA
29.0(Clearances and Creepage distances and solid insulation)	-	500	NA
30.0(Resistance to heat and fire)	-	500	NA

Complete

07 Aug, 2028

IS/IEC 60335 : Part 2 : Sec 89 (2010)

Household and similar electrical appliances - Safety: Part 2 - 89: particular requirements for commercial refrigerating appliances with an incorporated or remote refrigerant unit or compressor

148000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 , 7.12, 7.14,7.15(Marking)	-	500	-
31(Resistance to rusting)	-	1000	-
30.1(Resistance to heat and fire)	-	5000	-
29 and table (creepage and Clearances distances )	-	5000	-
28.1, Table No.-14(Screws and connections)	-	1250	-
28.2 to 28.4(Screws and connections)	-	1250	-
27, 27.1 to 27.6(Provision for earthing)	-	1500	-
26, 26.1 to 26.11(Terminals for external conductors)	-	1500	-
25.1(Supply connection and external flexible cords)	-	1000	-
24(Components)	-	0	-
23.1 & 23.2(Internal wiring)	-	400	-
23.3(Internal wiring)	-	400	-
23.4(Internal wiring)	-	400	-
23.5 to 23.8(Internal wiring)	-	400	-
23.9 ,23.10(Internal wiring)	-	400	-
22.1(Constructions)	-	300	-
22.2(Constructions)	-	300	-
22.3(Constructions)	-	300	-
22.4(Constructions)	-	300	-
22.5(Constructions)	-	300	-
22.6(Constructions)	-	300	-
22.7 to 22.10(Constructions)	-	300	-
22.11(Constructions)	-	300	-
22.12(Constructions)	-	300	-
22.13 to 22.52(Constructions)	-	300	-
22.101 to 22.102(Constructions)	-	300	-
22.103(Constructions)	-	300	-
22.104(Constructions)	-	300	-
22.105 to 22.114(Constructions)	-	300	-
21.1(MECHANICAL STRENGTH)	-	2400	-
21.2(MECHANICAL STRENGTH)	-	2400	-
20.2(Stability and mechanical hazards)	-	5000	-
19(ABNORMAL OPERATION)	-	15000	-
17(Overload protection of transformers and associated circuits)	-	2000	-
16 & 16.1(Leakage current and electric strength)	-	2500	-
15(Moisture resistance)	-	25000	-
14(Transient Over Voltage & table 6)	-	5000	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	2500	-
11(TEMPERATURE RISE)	-	15000	-
10.1(Power input and current)	-	15000	-
8, 8.1(Protection against access to live parts)	-	2000	-

Complete

07 Aug, 2028

-
-

IS 10322 : Part 5 : Sec 9 (2017)

Luminaires: Part 5 particular requirements: Sec 9 rope lights

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.6(Marking)	-	500	-
21.7(Construction)	-	5000	-
21.8(Creepage Distance and Clearances)	-	500	-
21.9(Provision for earthing)	-	1000	-
21.10(Terminals)	-	1000	-
21.11(External & Internal Wiring)	-	1000	-
21.12(Protection against electric shock)	-	1000	-
21.13(Endurance Tests and Thermal Tests)	-	15000	-
21.14(Resistance to Dust & Moisture)	-	12000	-
21.15(Insulation Resistance and Electric Strength)	-	2500	-
21.16(Resistance to Heat , fire and tracking)	-	5000	-

Complete

07 Aug, 2028

-
-

IS 10322 : PART 5 : SEC 3 (2012)

Luminaires: Part 5 particular requirements: Sec 3 luminaires for road and street lighting (First Revision)

64125 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Marking)	-	500	For BIS Samples: 1.5 times of BIS Testing Charges.
7.0(Construction)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
8.0(Creepage Distance and Clearances)	-	500	For BIS Samples: 1.5 times of BIS Testing Charges.
9.0(Provision for earthing)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
10.0(Terminals)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
11.0(External & Internal Wiring)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
12.0(Protection against electric shock)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
13.0(Endurance Tests and Thermal Tests)	-	22625	For BIS Samples: 1.5 times of BIS Testing Charges.
14.0(Resistance to Dust & Moisture)	-	15000	For BIS Samples: 1.5 times of BIS Testing Charges.
15.0(Insulation Resistance and Electric Strength)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
16.0(Resistance to Heat , fire and tracking)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
17.0(Photometric Test)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges.

Complete

07 Aug, 2028

-
-

IS 7872 (2020)

Deep Freezers - Specification ( Second Revision )

286000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Safety Requirements)	-	118000	-
5.4.3(Individual Strength - Pressure Test)	-	12000	-
5.4.2(Individual Strength - Pressure Test)	-	12000	-
11.7(Pressure Test)	-	12000	-
4.8(Door and Fittings)	-	0	NA since this is part of construction
7(Sound Pressure Level)	-	12000	-
8(Freezer Storage Capacity)	-	20000	-
11.1(No load Pull down Test)	-	25000	-
11.2(Energy Consumption Test)	-	30000	-
11.3(Temperature Rise Test)	-	15000	-
11.4(Door Seal Test)	-	12000	-
11.5(Mechanical Strength of Shelves and Similar Components)	-	12000	-
11.6(Thermal Insulation Test ( External Condensation))	-	30000	-

Complete

07 Aug, 2028

-
-

IS 9873 : Part 9 (2017)

Safety of Toys Part 9 Certain Phthalates Esters in Toys and Children's Products

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.0(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	3000		3000 per component
3.0(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	3000		3000 per component

Complete

07 Aug, 2028

-
-

IS 16333 : Part 3 (2017)

Mobile phone handsets: Part 3 indian language support for mobile phone handsets - Specific requirements (First Revision)

15750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1(Inputting of text)	-	7875		--
5.2(Message Readability)	-	7875		--

Complete

07 Aug, 2028

-
-

IS 15644 (2006)

Safety of electric toys

ALL TYPE

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
20.0(Radiation, toxicity and similar hazards)	-	4500	40% discount for BIS.
15644 Cl. 20(Radiation, toxicity and similar hazards)	-	4500	40% discount for BIS.
15644 Cl. 7(Marking and instructions)	-	5000	40% discount for BIS.
15644 Cl. 8(Power Input)	-	5000	40% discount for BIS.
15644 Cl. 9(Heating and abnormal operation)	-	5000	40% discount for BIS.
15644 Cl. 10(Electrical strength at operating temperature)	-	5000	40% discount for BIS.
15644 Cl. 11.1(Moisture resistance)	-	5000	40% discount for BIS.
15644 Cl. 11.2(Resistant to humidity)	-	5000	40% discount for BIS.
15644 Cl. 12(Electric strength at room temperature)	-	5000	40% discount for BIS.
15644 Cl. 13(Mechanical strength)	-	5000	40% discount for BIS.
15644 Cl. 14.1(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.2(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.3(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.4(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.5(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.6(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.7(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.8(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.9(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.1(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.11(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.12(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.13(Construction)	-	5000	40% discount for BIS.
15644 Cl. 14.14(Construction)	-	5000	40% discount for BIS.
15644 Cl. 15.1(Protection of cords and wires)	-	5000	40% discount for BIS.
15644 Cl. 15.2(Protection of cords and wires)	-	5000	40% discount for BIS.
15644 Cl. 16(Components)	-	5000	40% discount for BIS.
15644 Cl. 17 Table-1(Screws and connections)	-	5000	40% discount for BIS.
15644 Cl. 17 Table-1(Nominal daimeter of screws made of insulating material)	-	5000	40% discount for BIS.
15644 Cl. 18(Clearance and creepage distance)	-	5000	40% discount for BIS.
15644 Cl. 19.1(Ball pressure test IEC 60695-10-2)	-	5000	40% discount for BIS.
15644 Cl. 19.2.1(Glow wire test IEC 60695-2-11)	-	5000	40% discount for BIS.
15644 Cl. 19.2.2(Needle flame test)	-	5000	40% discount for BIS.
9873 (Part-3) 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9)	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-3) 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 )	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-3) 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 )	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-3) 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9)	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-3) 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 )	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-3) 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 )	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-3) 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 )	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-3) 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 )	-	4500	INR 4500 per components and Total Discount 40% Discount.
9873 (Part-9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	6000	INR 6000 per components and Total Discount 40% Discount.
9873 (Part-9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	6000	INR 6000 per components and Total Discount 40% Discount.
9873 (Part-9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	6000	INR 6000 per components and Total Discount 40% Discount.
9873 (Part-9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	6000	INR 6000 per components and Total Discount 40% Discount.

Complete

07 Aug, 2028

-
Excluding: Cl.16 Components. Except Annex-E: Toys incorporating lasers and LED

IS 302 : Part 1 (2008)

Safety of household and similar electrical appliances: Part 1 general requirements (Sixth Revision)

79000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	500	-
8.1.1(Protection against live parts in all positions)	-	1000	-
10.1(Power input)	-	2500	-
10.2(Current input)	-	2500	-
11.3(Heating)	-	8000	-
13.2(Leakage current at operating temperature)	-	1250	-
13.3(Electric Strength at operating temperature)	-	1250	-
14(Transient Over Voltages)	-	1000	-
15.0(General)	-	2000	-
16.0(General)	-	2500	-
17(Over Load Protection of Transformers and associated circuits)	-	8000	-
18(Endurance Test requirements and tests)	-	5000	-
19(Abnormal Operation)	-	8000	-
20(Stability test)	-	1000	-
21(Mechanical Strength Test)	-	1500	-
22(Construction verification related test)	-	2000	-
23(General)	-	1000	-
24(Components)	-	1000	-
25(Supply connection and external flexible cords)	-	1500	-
26(Terminals for external conductors)	-	1000	-
27(Provision for earthing)	-	1000	-
28(Screw test and connections)	-	1000	-
29(clearance, creepage distances and solid insulation)	-	1000	-
30.1(Ball pressure test)	-	4000	-
30.2(Needle Flame Test)	-	3000	-
30.2(Glow Wire Test)	-	3000	-
32(Radiation Toxicity and Similar Hazards)	-	10000	-
31(Resistance to Rusting)	-	1500	-

Complete

07 Aug, 2028

-
Excluding: EMI/EMC (Cl.19.11.4.1 to 19.11.4.4), Components (Cl.24).

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

195000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1.6(Power interface .)	-	5000	Test
1.7(Markings and instructions)	-	1000	Test
2.1(Protection from electric shock and energy hazards)	-	8000	Test
2.2(SELV circuits)	-	3000	Test
2.3(TNV circuits)	-	5000	Test
2.4(Limited current circuits)	-	3000	Test
2.5(Limited power sources .)	-	5000	Test
2.6(Provisions for earthing and bonding)	-	3000	Test
2.7(Overcurrent and earth fault protection in primary circuits)	-	2000	Test
2.8(Safety interlocks)	-	2500	Visual
2.9(Electrical insulation)	-	37000	Test
2.10(Clearances, creepage distances and distances through insulation)	-	22000	Measurement
3.1(General)	-	1000	Visual
3.2(Connection to a mains supply)	-	2500	Visual
3.3(Wiring terminals for connection of external conductors)	-	1000	Visual
3.4(Disconnection from the mains supply)	-	1000	Visual
3.5(Interconnection of equipment)	-	1000	Visual
4.1(Stability)	-	1000	Test
4.2(Mechanical strength)	-	15000	Test
4.3(Design and construction)	-	10000	Test
4.4(Protection against hazardous moving parts)	-	500	Visual
4.5(Thermal requirements)	-	16000	Test
4.6(Openings in enclosures)	-	16000	Test
4.7(Resistance to fire)	-	5000	Test
5.1(Touch current and protective conductor curren)	-	3000	Test
5.2(Electric strength)	-	3000	Test
5.3(Abnormal operating and fault conditions)	-	5000	Test
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment)	-	2000	Test
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	2000	Test
6.3(Protection of the telecommunication wiring system from overheating)	-	2000	Test
7.1(General)	-	500	Visual
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment)	-	2000	Test
7.3(Protection of equipment users from overvoltages on the cable distribution system)	-	1000	Test
7.4(Insulation between primary circuits and cable distribution systems)	-	500	Test
1.5(Components)	-	1000	Visual verification of components and associated certificates
2.8.2/2.8.5(Interlock switches)	-	1000	Visual verification of components and associated certificates
2.8.7(Switches and Relay)	-	500	Visual verification of components and associated certificates
2.10.5.4(Opto-coupler)	-	500	Visual verification of components and associated certificates
2.10.5.12(Wires in wound components)	-	500	Visual verification of components and associated certificates
2.10.6(PCB material)	-	500	Visual verification of components and associated certificates
3.2.5(Non re-wirable plug with PVC sheathed cable)	-	500.0	Visual verification of components and associated certificates
4.2.8(Cathode Ray Tubes)	-	0	Not applicable as no products with such construction
4.3.12(Flammable liquids)	-	0	Not applicable as no products with such construction
4.3.13.2(Ionizing radiation)	-	0	Not applicable as no products with such construction
4.3.13.3/ Annex Y(Effect of UV radiation on material/Ultraviolet conditioning test)	-	0	Not applicable as no products with such construction
4.3.13.4(Human exposure to ultraviolet (UV) radiation)	-	500	Visual verification of components and associated certificates
4.3.13.5(LED, laser class)	-	500	Visual verification of components and associated certificates
Annex A3(Hot flaming oil test)	-	0	Not applicable as no products with such construction not applicable
Annex U(Insulating winding wires for use without interleaved insulation)	-	500	Visual verification of components and associated certificates
Annex CC(Evaluation of integrated circuit (IC) current limiters)	-	500	Visual verification of components and associated certificates
Annex K(Thermal Control)	-	500	Visual verification of components and associated certificates
Annex Q(Voltage Dependent Resistors)	-	500	Visual verification of components and associated certificates
4.3.10(Dust, powders, liquids and gases)	-	0	Not applicable as no products with such construction
4.3.11(Containers for liquids or gases)	-	0	Not applicable as no products with such construction

Complete

07 Aug, 2028

-
Excluding: Cl. 1.5 (Components), Cl. 2.8.2/2.8.5 (Interlock switches), Cl. 2.8.7 (Switches and Relay), Cl. 2.10.5.4 (Opto-coupler), Cl. 2.10.5.12 (Wires in wound components), Cl. 2.10.6 (PCB material), Cl. 3.2.5 (Non re-wirable plug with PVC sheathed cable), Cl. 4.3.13.2 (Ionizing radiation), Cl. 4.3.13.3/ Annex Y (Effect of UV radiation on material/Ultraviolet conditioning test), Cl. 4.3.13.4 (Human exposure to ultraviolet (UV) radiation), Cl. 4.3.13.5 (LED, laser class), Cl. Annex U (Insulating winding wires for use without interleaved insulation), Cl. Annex CC (Evaluation of integrated circuit (IC) current limiters), Annex K (Thermal Control), Annex Q (Voltage Dependent Resistors)

IS/IEC 60730 : Part 2 : Sec 9 (2011)

Automatic Electrical Controls for Household and Similar Use Part 2 Particular Requirements Section 9 Temperature Sensing Controls

200000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Test finger as shown in figure 2 with force 20 N/30 N)	-	5000	-
9(By inspection)	-	5000	-
10.1.5(By measurement)	-	8000	-
11.2(by inspection and by test)	-	25000	-
12.1(As per IEC 60529)	-	12500	-
12.2(Humidity treatment at 91 % and 95 % and temp between 20 to 30°C)	-	12500	-
13.1(as per table 13.1)	-	10000	-
14.1(As per table 14.1)	-	40000	-
16.2(as per cl 16.2.1 to 16.2.3 )	-	10000	-
17.6(as per cl 17.6.1 and 17.6.2)	-	20000	-
18.2(Impact tester)	-	8000	-
19.2.1(By inspection)	-	1500	-
20.1(as per table 20.2)	-	1000	-
21.2.2 to 21.2.6(Ball pressure test as per cl 21.2.5)	-	10000	-
22.1.1(As per cl 21.1.3 to 21.1.6)	-	1000	-
24.1(as per IEC 60127 or IEC 60269)	-	0	-
25(as per annexure H)	-	10000	-
27.2(as per cl 27.2.1 and 27.2.2)	-	10000	-
15(as per cl 15.1 to 15.4)	-	5000	-

Complete

07 Aug, 2028

-
Excluding: EMI/EMC requirements – emission (Cl.23), EMI/EMC requirements – immunity (Cl.26)

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

61500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Classification of Luminaires')	-	500	N/A
7.0(Construction)	-	1000	N/A
8.0(Creepage Distance and Clearances)	-	500	N/A
9.0(Provision for earthing)	-	1000	N/A
10.0(Terminals)	-	1000	N/A
11.0(External & Internal Wiring)	-	1000	N/A
12.0(Protection against electric shock)	-	1000	N/A
13.0(Endurance Tests and Thermal Tests)	-	30000	N/A
14.0(Resistance to Dust & Moisture)	-	15000	N/A
15.0(Insulation Resistance and Electric Strength)	-	5000	N/A
16.0(Resistance to Heat , fire and tracking)	-	5000	N/A
17.0(Photometric Test)	-	10000	N/A

Complete

07 Aug, 2028

-
Scope restricted for rating up to 600 V.

IS 10322 : Part 5 : Sec 2 (2012)

Luminaires: Part 5 particular requirements: Sec 2 recessed luminaires (First Revision)

71500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking)	-	500	For BIS Samples: 1.5 times of BIS Testing Charges.
7(Construction)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
8(Creepage Distance and Clearances)	-	500	For BIS Samples: 1.5 times of BIS Testing Charges.
9(Provision for earthing)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
10(Terminals)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
11(External & Internal Wiring)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
12(Protection against electric shock)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
13(Endurance Tests and Thermal Tests)	-	30000	For BIS Samples: 1.5 times of BIS Testing Charges.
14(Resistance to Dust and Moisture)	-	15000	For BIS Samples: 1.5 times of BIS Testing Charges.
15(Insulation Resistance and Electric Strength)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
16(Resistance to Heat , fire and tracking)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
17(Photometric Test)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges.

Complete

07 Aug, 2028

-
Scope restricted for rating up to 600 V and Gonio Photometer Travel Length up to 8.5 m (Cl.17 & RD Cl.6.2 of IS 13383 (Part-1).

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

62438 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges
8(Protection against accidental contact with live parts)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges
9(Terminals)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges
10(PROVISION FOR EARTHING)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges
11(MOISTURE RESISTANCE)	-	7000	For BIS Samples: 1.5 times of BIS Testing Charges
12(Electric Strength)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges
14(Fault conditions)	-	14438	For BIS Samples: 1.5 times of BIS Testing Charges
15(Transformer heating)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges
17(Creepage distance and clearances)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges
18(Screws, current carrying parts and connections)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges
19(Resistance to heat, fire and tracking)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges
20(Resistance to corrosion)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges

Complete

07 Aug, 2028

-
Excluding: Components (Enclosure, Bridging resistor in primary circuit, Capacitor and RC units, RF suppression (X-Y capacitors) Inductor, MOV/VDR, SMPS / Mains Transformer, PCB material, Metal base PCB for LED, Transparent cover, bobbin, Insulated tape, Heat shrinkage sleeve, Connector, Fuse, Internal wire, LED, Optocoupler, EMI/EMC filter, Winding wire, Thin sheet materials.

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

43875 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	5000	Marking test
6(Interchangeability)	-	8000	Test
7(Protection against accidental contact with live parts)	-	3000	Test
8(Insulation Resistance and Electric Strength)	-	2000	Test
9(MECHANICAL STRENGTH)	-	6875	Test
10(cap temperature)	-	5000	Test
11(Resistance to Heat)	-	2000	Test
12(Resistance to Flame and Ignition)	-	1000	Test
13(Fault conditions)	-	10000	Test
14(Creepage distance and clearances)	-	1000	Measurement

Complete

07 Aug, 2028

-
Scope restricted for rating up to 600 V and cap type B22d, E14 & E27 only

IS 16103 : Part 1 (2012)

Led modules for general lighting: Part 1 safety requirements

37500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1000	N/A
8(Terminals)	-	1000	N/A
9(PROVISION FOR EARTHING)	-	1000	N/A
10(Protection against accidental contact with live parts)	-	1000	N/A
11(Mositure Resistance and Insulation)	-	4000	N/A
12(Electric Strength)	-	1000	N/A
13(Fault conditions)	-	5000	N/A
16(Creepage distance and clearances)	-	3500	N/A
17(Screws, current carrying parts and connections)	-	1000	N/A
18(Resistance to heat, fire and tracking)	-	1000	N/A
19(Resistance to corrosion)	-	3000	N/A

Complete

07 Aug, 2028

-
Scope restricted for rating up to 600 V.

IS 16103 : Part 2 (2012)

Led modules for general lighting: Part 2 performance requirements

90000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Information for Luminaire design)	-	0	NA
10(LED Module Life)	-	70000	Life
9(Chromaticity Coordinates, Correlated colour temperature and colour rendering)	-	10000	CCT, CRI
8(Light Output)	-	4000	Light Output
7(Module Power)	-	4000	Module Power
6(Dimensions)	-	2000	Dimension

Complete

07 Aug, 2028

-
Scope restricted for rating up to 600 V. Excluding: Test for Emission (Radiated & Conducted) of Radio Frequency Disturbances (Cl. 13).

IS 16107 : Part 2 : Sec 1 (2012)

Luminaires performance: Part 2 particular requirements: Sec 1 led luminaire

102000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(LED Luminaire Life)	-	70000	Life
9(Chromaticity Coordinates, Correlated colour temperature and colour rendering)	-	12000	CCT, CRI
8(Light Output)	-	10000	Light Output
7(Total Input Power)	-	10000	Power

Complete

07 Aug, 2028

-
-

IS 10322 : Part 5 : Sec 5 (2013)

Luminaires: Part 5 particular requirements: Sec 5 floodlights (First Revision)

71500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Marking)	-	500	For BIS Samples: 1.5 times of BIS Testing Charges.
7.0(Construction)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
8.0(Creepage Distance and Clearances)	-	500	For BIS Samples: 1.5 times of BIS Testing Charges.
9.0(Provision for earthing)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
10.0(Terminals)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
12.0(Protection against electric shock)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
13.0(Endurance Tests and Thermal Tests)	-	30000	For BIS Samples: 1.5 times of BIS Testing Charges.
14.0(Resistance to Dust & Moisture)	-	15000	For BIS Samples: 1.5 times of BIS Testing Charges.
15.0(Insulation Resistance and Electric Strength)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
16.0(Resistance to Heat , fire and tracking)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
17.0(Photometric Test)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges.

Complete

07 Aug, 2028

-
Scope restricted for rating up to 600 V.

IS 10322 : Part 5 : Sec 6 (2013)

Luminaires: Part 5 particular requirements: Sec 6 handlamps

61500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Marking)	-	500	N/A
7.0(Construction)	-	1000	N/A
8.0(Creepage Distance and Clearances)	-	500	N/A
9.0(Provision for earthing)	-	1000	N/A
10.0(Terminals)	-	1000	N/A
11.0(External & Internal Wiring)	-	1000	N/A
12.0(Protection against electric shock)	-	1000	N/A
13.0(Endurance Tests and Thermal Tests)	-	30000	N/A
14.0(Resistance to Dust & Moisture)	-	15000	N/A
15.0(Insulation Resistance and Electric Strength)	-	5000	N/A
16.0(Resistance to Heat , fire and tracking)	-	5000	N/A

Complete

07 Aug, 2028

-
-

IS 10322 : Part 5 : Sec 8 (2013)

Luminaires: Part 5 particular requirements: Sec 8 emergency lighting

68250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Marking)	-	500	For BIS Samples: 1.5 times of BIS Testing Charges.
7.0(Construction)	-	2000	For BIS Samples: 1.5 times of BIS Testing Charges.
8.0(Creepage Distance and Clearances)	-	1500	For BIS Samples: 1.5 times of BIS Testing Charges.
9.0(Provision for earthing)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
10.0(Terminals)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
11.0(External & Internal Wiring)	-	1250	For BIS Samples: 1.5 times of BIS Testing Charges.
12.0(Protection against electric shock)	-	1000	For BIS Samples: 1.5 times of BIS Testing Charges.
13.0(Endurance Tests and Thermal Tests)	-	12000	For BIS Samples: 1.5 times of BIS Testing Charges.
14.0(Resistance to Dust & Moisture)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges.
15.0(Insulation Resistance and Electric Strength)	-	3000	For BIS Samples: 1.5 times of BIS Testing Charges.
16.0(Resistance to Heat , fire and tracking)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
17.0(Functional Safety)	-	8000	For BIS Samples: 1.5 times of BIS Testing Charges.
18.0(Changeover Operation)	-	5000	For BIS Samples: 1.5 times of BIS Testing Charges.
19.0(High Temperature Operation)	-	10000	For BIS Samples: 1.5 times of BIS Testing Charges.
20.0(BATTERY CHARGERS FOR SELFCONTAINED EMERGENCY LUMINAIRES)	-	7000	For BIS Samples: 1.5 times of BIS Testing Charges.

Complete

07 Aug, 2028

-
Scope restricted for rating up to 600 V.

IS 302 : Part 2 : Sec 25 (2014)

Safety of household and similar electrical appliances: Part 2 Particular requirements: Section 25 Microwave ovens

148000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	1000	N/A
8(Protection against live parts)	-	1000	N/A
10(POWER INPUT AND CURRENT)	-	5000	N/A
11(HEATING)	-	12000	N/A
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	3500	N/A
14(IMPULSE VOLTAGE TEST)	-	1000	N/A
15(HUMIDITY TREATMENT TEST)	-	10000	N/A
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	2500	N/A
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	10000	N/A
18(ENDURANCE)	-	20000	N/A
19(ABNORMAL OPERATION)	-	8000	Excluding: EMI/EMC (Cl.19.11.4.1 to 19.11.4.4),
20(STABILITY AND MECHANICAL HAZARDS)	-	1000	N/A
21(MECHANICAL STRENGTH)	-	2500	N/A
22(CONSTRUCTION)	-	10000	Visual inspection for construction verification
23(INTERNAL WIRING)	-	1000	N/A
24(COMPONENTS)	-	5000	Visual verification of components and associated certificates
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CORDS)	-	1500	N/A
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	1000	N/A
27(PROVISION FOR EARTHING)	-	1000	N/A
28(SCREWS AND CONNECTIONS)	-	1000	N/A
29(CLEARANCES, CREEPAGE DISTANCES AND SOLID INSULATION)	-	31000	N/A
30(RESISTANCE TO HEAT AND FIRE)	-	25000	N/A
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	5000	N/A

Complete

07 Aug, 2028

-
Test facility of Supply connection & external flexible cables & cords (Cl.25.14) included w.e.f. 16-12-2019. Excluding: EMI/EMC (Cl.19.11.4.1 to 19.11.4.4)

IS 10322 : Part 5 : Sec 7 (2017)

Luminaires: Part 5 particular requirements: Sec 7 lighting chains (First Revision)

61500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
20.6(Marking)	-	500	N/A
20.7(Construction)	-	1000	N/A
20.8(Creepage Distance and Clearances)	-	500	N/A
20.9(Provision for earthing)	-	1000	N/A
20.10(Terminals)	-	1000	N/A
20.11(External & Internal Wiring)	-	1000	N/A
20.12(Protection against electric shock)	-	1000	N/A
20.13(Endurance Tests and Thermal Tests)	-	30000	N/A
20.14(Resistance to Dust & Moisture)	-	15000	N/A
20.15(Insulation Resistance and Electric Strength)	-	5000	N/A
20.16(Resistance to Heat , fire and tracking)	-	5000	N/A

Complete

07 Aug, 2028

-
-

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

All Types

2800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2-5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	1500	40% DISCOUNT FOR BIS.
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	1200	40% DISCOUNT FOR BIS.
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-	1500	40% DISCOUNT FOR BIS.
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	1800	40% DISCOUNT FOR BIS.
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	1800	40% DISCOUNT FOR BIS.
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame)	-	2000	40% DISCOUNT FOR BIS.
4.5-5.5(Soft-filled toys-Test for soft-filled toys )	-	1200	40% DISCOUNT FOR BIS.

Complete

07 Aug, 2028

-
-

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

ALL TYPE

10980 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 - 5.24.6.2( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.3( Reasonably foreseeable abuse -Tip-over test for large and bulky toys)	-	800	40% DISCOUNT FOR BIS.
4.2 - 5.24.4( Reasonably foreseeable abuse -Dynamic strength test for wheeled ride-on toys other than toy scooters)	-	1800	40% DISCOUNT FOR BIS.
4.2 - 5.24.5( Reasonably foreseeable abuse -Torque test)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.6.3( Reasonably foreseeable abuse -Tension test for pompoms)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.6.4( Reasonably foreseeable abuse -Tension test for protective components)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.6.5( Reasonably foreseeable abuse -Tension test for a projectile with a suction cup)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.7( Reasonably foreseeable abuse -Compression test)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.8.2( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.8.3( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent)	-	1200	40% DISCOUNT FOR BIS.
4.3.2 - 5.21( Expanding materials)	-	1000	40% DISCOUNT FOR BIS.
4.4.1 - 5.2(Small parts-For children under 36 months)	-	1500	40% DISCOUNT FOR BIS.
4.4.2 - 5.2(Small parts-For children 36 months and over but under 72 months )	-	1500	40% DISCOUNT FOR BIS.
4.5.1.2 - 5.3(Shape, size and strength of certain toys-Squeeze toys, rattles, and certain other toys and components of toys-Test for shape and size of certain toys)	-	1200	40% DISCOUNT FOR BIS.
4.5.2 - 5.4(Shape, size and strength of certain toys-Small balls-Small balls test)	-	1200	40% DISCOUNT FOR BIS.
4.5.3 - 5.5(Shape, size and strength of certain toys-Pompoms-Test for pompoms)	-	1000	40% DISCOUNT FOR BIS.
4.5.4 - 5.6(Shape, size and strength of certain toys- Pre-school play figures-Test for pre-school play figures)	-	800	40% DISCOUNT FOR BIS.
4.5.5(Shape, size and strength of certain toys-Toy pacifiers-Nipple length)	-	800	40% DISCOUNT FOR BIS.
4.5.7(Shape, size and strength of certain toys-Marbles)	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening)	-	1200	40% DISCOUNT FOR BIS.
4.6.1 a - 5.8(Edges-Accessible sharp edges of glass or metal-Sharp edge test)	-	1500	40% DISCOUNT FOR BIS.
4.7.1 - 5.9(Points-Accessible sharp points-sharp-point test)	-	1500	40% DISCOUNT FOR BIS.
4.8.1(Projections-General requirments)	-	1200	40% DISCOUNT FOR BIS.
4.9(a) - 5.24.8.2( Metal wires and rods-wires and other metallic components intended to be bent)	-	1200	40% DISCOUNT FOR BIS.
4.9(b) - 5.24.8.3( Metal wires and rods-wires likely to be bent)	-	1200	40% DISCOUNT FOR BIS.
4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys-average thickness)	-	1000	40% DISCOUNT FOR BIS.
4.11.2.1(a) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	800	40% DISCOUNT FOR BIS.
4.11.2.1(b) - 5.11.3( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-breakaway feature separation test)	-	1050	40% DISCOUNT FOR BIS.
4.11.2.1(b) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test)	-	800	40% DISCOUNT FOR BIS.
4.11.2.2 - 5.11.2( Cords-Cords in toys intended for children under 18 months--Other cords-free length )	-	800	40% DISCOUNT FOR BIS.
4.11.3.1(a) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	1050	40% DISCOUNT FOR BIS.
4.11.3.1(b) - 5.11.3( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-breakaway feature separation test)	-	1050	40% DISCOUNT FOR BIS.
4.11.3.1(b) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test)	-	800	40% DISCOUNT FOR BIS.
4.11.4(a) - 5.11.4.1(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Head probe push test)	-	1200	40% DISCOUNT FOR BIS.
4.11.4(a) - 5.11.4.2(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Elastic materials)	-	1200	40% DISCOUNT FOR BIS.
4.11.4(b) - 5.11.3(Cords-Fixed loops and nooses intended for children under 36 months-Breakaway feature separation test)	-	1050	40% DISCOUNT FOR BIS.
4.11.5 - 5.11.2(Cords-Cords on pull toys-free length)	-	800	40% DISCOUNT FOR BIS.
4.11.6(Cords- Electrical cables)	-	1800	40% DISCOUNT FOR BIS.
4.11.7 - 5.11.1(Cords- Diameter of certain cords intended for children under 36 months-cords cross-sectional dimension)	-	1000	40% DISCOUNT FOR BIS.
4.11.8 - 5.11.5(Cords- Self-retracting cords intended for children under 36 months-self-retracting cords)	-	1500	40% DISCOUNT FOR BIS.
4.11.9.1(Cords-Toys intended to be strung across a cradle, cot, perambulator or carriage)	-	1800	40% DISCOUNT FOR BIS.
4.11.9.2 (Cords-Toys otherwise intended to be attached to a cradle, cot, perambulator or carriage)	-	1800	40% DISCOUNT FOR BIS.
4.11.10(Cords-Cords on toy bags)	-	1800	40% DISCOUNT FOR BIS.
4.11.11 - 5.11.6( Cords, strings and lines for flying toys- electrical resistance)	-	1800	40% DISCOUNT FOR BIS.
4.12.1(a - 2)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	1650	40% DISCOUNT FOR BIS.
4.12.1(a - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators)	-	1650	40% DISCOUNT FOR BIS.
4.12.2 (a) - 5.22.3(Folding mechanisms-Other toys with folding mechanisms)	-	1650	40% DISCOUNT FOR BIS.
4.12.3(Folding mechanisms-Hinge line clearance)	-	1650	40% DISCOUNT FOR BIS.
4.13.1(Holes, clearances and accessibility of mechanisms-Circular holes in rigid materials)	-	1500	40% DISCOUNT FOR BIS.
4.13.2 (Holes, clearances and accessibility of mechanisms-Accessible clearances for movable segments)	-	1500	40% DISCOUNT FOR BIS.
4.13.3 - 5.7(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys-accessibility of a part or component)	-	1500	40% DISCOUNT FOR BIS.
4.13.4(Holes, clearances and accessibility of mechanisms-Other driving mechanisms)	-	1500	40% DISCOUNT FOR BIS.
4.13.5(Holes, clearances and accessibility of mechanisms-Winding keys)	-	1500	40% DISCOUNT FOR BIS.
4.14(a)(Springs)	-	1200	40% DISCOUNT FOR BIS.
4.14(b)(Springs)	-	1200	40% DISCOUNT FOR BIS.
4.14(c)(Springs)	-	1200	40% DISCOUNT FOR BIS.
4.15.1.1 - 5.12.2( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet available for stabilization)	-	800	40% DISCOUNT FOR BIS.
4.15.1.2 - 5.12.3( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet unavailable for stabilization)	-	1000	40% DISCOUNT FOR BIS.
4.15.1.3 - 5.12.4( Stability and overload requirements-Stability of ride-on toys and seats-Fore and aft stability Test)	-	1000	40% DISCOUNT FOR BIS.
4.15.2 - 5.12.5( Stability and overload requirements-Overload requirements for ride-on toys and seats-overload test for ride-on toys and seats)	-	1200	40% DISCOUNT FOR BIS.
4.15.2 - 5.24.4( Stability and overload requirements-Overload requirements for ride-on toys and seats-dynamic strength test for wheeled ride-on toys other than toy scooters)	-	1200	40% DISCOUNT FOR BIS.
4.15.3 - 5.12.6( Stability and overload requirements-Stability of stationary floor toy-Stability test of stationary floor toys)	-	1200	40% DISCOUNT FOR BIS.
4.17 - 5.14(Simulated protective equipment, such as helmets, hats and goggles-Impact test for toys that cover the face)	-	1700	40% DISCOUNT FOR BIS.
4.18.2(a) - 5.36(Projectile toys-Projectiles-tip assessment of rigid projectiles)	-	1200	40% DISCOUNT FOR BIS.
4.18.2(b)(Projectile toys-Projectiles)	-	1800	40% DISCOUNT FOR BIS.
4.18.2(d) - 5.37(Projectile toys-Projectiles-length of suction cup projectiles)	-	1250	40% DISCOUNT FOR BIS.
4.18.2 - e - 5.24.5(Projectile toys-Projectiles-torque test)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(a) - 5.3 - 5.24(Projectile toys-Projectile toys with stored energy-small parts test after reasonably foreseeable abuse testing)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(b)(Projectile toys-Projectile toys with stored energy)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(d) - 5.15.2(Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles)	-	1500	40% DISCOUNT FOR BIS.
4.18.3(e )(Projectile toys-Projectile toys with stored energystored energy-Discharge mechanism)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.2(a) - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-determination of the kinetic energy per area of contact when the contact area of the dart shall be at least 3 cm^2)	-	1500	40% DISCOUNT FOR BIS.
4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After torque test)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.3 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-kinetic energy per area)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.6 - 5.24.5(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After torque test)	-	1800	40% DISCOUNT FOR BIS.
4.19(Rotors and propellers)	-	600	40% DISCOUNT FOR BIS.
4.2(Aquatic toys)	-	1500	40% DISCOUNT FOR BIS.
4.21(a)(Braking-brake performance for mechanically or electrically powered ride-on toys other than toy bicycles)	-	1500	40% DISCOUNT FOR BIS.
4.21(b)(braking)	-	1500	40% DISCOUNT FOR BIS.
4.22.1(Toy bicycles-Instructions for use)	-	1250	40% DISCOUNT FOR BIS.
4.22.2(Toy bicycles-Determination of maximum saddle height)	-	1250	40% DISCOUNT FOR BIS.
4.22.3 - 5.16.1(Toy bicycles-Braking requirements-determination of free-wheeling facility)	-	1250	40% DISCOUNT FOR BIS.
4.23 - 5.17(Speed limitation of electrically driven ride-on toys-determination of speed of electrically driven ride-on toys)	-	1600	40% DISCOUNT FOR BIS.
4.24(a) - 5.18(Toys containing a heat source-determination of temperature increases)	-	1200	40% DISCOUNT FOR BIS.
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of glass or porcelain))	-	1200	40% DISCOUNT FOR BIS.
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy(Parts made of metals))	-	1200	40% DISCOUNT FOR BIS.
4.25 - 5.19(Liquid-filled toys-leakage of liquid-filled toys)	-	1000	40% DISCOUNT FOR BIS.
4.27(Toy roller skates, toy inline skates and toy skateboards)	-	1000	40% DISCOUNT FOR BIS.
4.28( Percussion caps specifically designed for use in toys)	-	1200	40% DISCOUNT FOR BIS.
4.29(a) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.29(b) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.29(c) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.29(d) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.29(e) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.29(f) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.30.2(Toy scooters-Warnings and instructions for use)	-	1450	40% DISCOUNT FOR BIS.
4.30.3 - 5.26 - 5.8(Toy scooters-Strength-After static strength for toy scooters- sharp edge test)	-	1500	40% DISCOUNT FOR BIS.
4.30.3 - 5.26 - 5.9(Toy scooters-Strength-static strength for toy scooters-sharp-point test)	-	1500	40% DISCOUNT FOR BIS.
4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters)	-	1500	40% DISCOUNT FOR BIS.
4.30.3 - 5.27(Toy scooters-Strength-dynamic strength for toy scooters)	-	1800	40% DISCOUNT FOR BIS.
4.30.4 - 5.12.2(Toy scooters-Stability-sideways stability test, feet available for stabilization)	-	1450	40% DISCOUNT FOR BIS.
4.30.5(f) - 5.30( Toy scooters-Adjustable and folding steering tubes and handlebars-resistance to separation of handlebar)	-	1200	40% DISCOUNT FOR BIS.
4.30.6 - 5.28( Toy scooters-Braking- force required to hold the toy)	-	1500	40% DISCOUNT FOR BIS.
4.30.7( Toy scooters-Wheel size(diameter))	-	1450	40% DISCOUNT FOR BIS.
4.30.8(Toy scooters-Projections)	-	1450	40% DISCOUNT FOR BIS.
4.31(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over)	-	1600	40% DISCOUNT FOR BIS.
4.32 - 5.38.1( Yo-yo balls - The ratio of the mass m (in grams) to the elastic constant k of the yo-yo ball tether(m/k))	-	1000	40% DISCOUNT FOR BIS.
4.33 - 5.11.3(Straps intended to be worn fully or partially around the neck-breakaway feature separation test)	-	1200	40% DISCOUNT FOR BIS.
4.34(Sledges and toboggans with cords for pulling)	-	800	40% DISCOUNT FOR BIS.
4.35.3 - 5.39(Jaw entrapment in handles and steering wheels-jaw entrapment test)	-	1450	40% DISCOUNT FOR BIS.
4.5.6(Shape, size and strength of certain toys-Balloons)	-	1200	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2 - 5.24.8.3( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent)	-	1200	40% DISCOUNT FOR BIS.
4.2 - 5.24.2( Reasonably foreseeable abuse -Drop Test)	-	1500	40% DISCOUNT FOR BIS.
4.5.1.3 - 5.3(Shape, size and strength of certain toys-Other toys or components of toys with nearly spherical, hemispherical, circular flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children under 18 months-Test for shape and size of certain toys)	-	1200	40% DISCOUNT FOR BIS.
4.5.1.4 - 5.3(Shape, size and strength of certain toys-Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical, or dome-shaped ends intended for children 18 months and over but under 48 months-Test for shape and size of certain toys)	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening in Base)	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening not in Base)	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening)	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening )	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening )	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys)	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys-The maximum distance between centrelines of adjacent peaks )	-	1200	40% DISCOUNT FOR BIS.
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys-Minimum depth)	-	1200	40% DISCOUNT FOR BIS.
4.6.1 b(Edges-Accessible sharp edges of glass or metal- gap between the edge and the adjacent surface)	-	1500	40% DISCOUNT FOR BIS.
4.6.2(Edges-Functional sharp edges)	-	1500	40% DISCOUNT FOR BIS.
4.6.3 - 5.8(Edges-Edges on metal toys-Sharp edge test)	-	1500	40% DISCOUNT FOR BIS.
4.6.4( Edges-Edges on moulded toys)	-	1500	40% DISCOUNT FOR BIS.
4.6.5( Edges-Edges on exposed bolts or threaded rod)	-	1500	40% DISCOUNT FOR BIS.
4.7.2 - a(Points-Functional sharp points)	-	1500	40% DISCOUNT FOR BIS.
4.7.2 - b(Points-Functional sharp points)	-	1500	40% DISCOUNT FOR BIS.
4.7.3 (Wooden toys)	-	1500	40% DISCOUNT FOR BIS.
4.9 - c( Metal wires and rods)	-	1500	40% DISCOUNT FOR BIS.
4.9 - c - 5.8( Metal wires and rods-Sharp edge test)	-	1500	40% DISCOUNT FOR BIS.
4.9 - c - 5.9( Metal wires and rods-Sharp Point test)	-	1500	40% DISCOUNT FOR BIS.
4.9 - c( Metal wires and rods-Minimum dia of spokes)	-	1500	40% DISCOUNT FOR BIS.
4.9 - c( Metal wires and rods-Spokes ends)	-	1500	40% DISCOUNT FOR BIS.
4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys- individual thickness)	-	1000	40% DISCOUNT FOR BIS.
4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys- individual thickness)	-	1000	40% DISCOUNT FOR BIS.
4.11.3.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords)	-	1800	40% DISCOUNT FOR BIS.
4.11.3.3 ( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords without a free end )	-	1800	40% DISCOUNT FOR BIS.
4.11.11( Cords, strings and lines for flying toys- )	-	1800	40% DISCOUNT FOR BIS.
4.12.1(a - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	1650	40% DISCOUNT FOR BIS.
4.12.1(a - 4)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	1650	40% DISCOUNT FOR BIS.
4.12.1(a - 5) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	1650	40% DISCOUNT FOR BIS.
4.12.1(b - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	1650	40% DISCOUNT FOR BIS.
4.12.1(b - 2) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	1650	40% DISCOUNT FOR BIS.
4.12.1(b - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	1650	40% DISCOUNT FOR BIS.
4.12.2 (b)(Folding mechanisms-Other toys with folding mechanisms)	-	1650	40% DISCOUNT FOR BIS.
4.13.3(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys)	-	1500	40% DISCOUNT FOR BIS.
4.17(Simulated protective equipment, such as helmets, hats and goggles)	-	1700	40% DISCOUNT FOR BIS.
4.18.2(c)(Projectile toys-Projectiles)	-	1800	40% DISCOUNT FOR BIS.
4.18.2(c)(Projectile toys-Projectiles-Radius)	-	1800	40% DISCOUNT FOR BIS.
4.18.2(d) - 5.37 - 5.24.5(Projectile toys-Projectiles-length of suction cup projectiles After torque test)	-	1250	40% DISCOUNT FOR BIS.
4.18.2(d) - 5.37 - 5.24.6.5(Projectile toys-Projectiles-length of suction cup projectiles After tension test for a projectile with a suction cup)	-	1250	40% DISCOUNT FOR BIS.
4.18.2 - e - 5.24.6.5(Projectile toys-Projectiles-tension test for a projectile with a suction cup)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(a) - 5.2(Projectile toys-Projectile toys with stored energy-small parts test)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(a) - 5.4(Projectile toys-Projectile toys with stored energy--small parts test after (wall impact test for projectiles)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(b) - 5.15.1.3.3(Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact)	-	1500	40% DISCOUNT FOR BIS.
4.18.3(c ) - 5.24.5(Projectile toys-Projectile toys with stored energy-torque test)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(c ) - 5.24.6.4(Projectile toys-Projectile toys with stored energy- tension test for protective components)	-	1800	40% DISCOUNT FOR BIS.
4.18.3(c )(Projectile toys-Projectile toys with stored energy)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.1 - 5.20(Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After torque test)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After tension test for protective components)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After tension test for protective components)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.3 - 5.15.2(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-wall impact test for projectiles)	-	1500	40% DISCOUNT FOR BIS.
4.18.4.3(a)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.3(b)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.3(c)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.6 - 5.24.5 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set- kinetic energy per area After torque test)	-	1500	40% DISCOUNT FOR BIS.
4.18.4.6 - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After tension test for protective components)	-	1800	40% DISCOUNT FOR BIS.
4.18.4.6 - 5.24.6.4 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-kinetic energy per area After tension test for protective components)	-	1500	40% DISCOUNT FOR BIS.
4.21(a)(braking)	-	1500	40% DISCOUNT FOR BIS.
4.22.3 (Toy bicycles-Braking requirements- brake lever dimension(d))	-	1250	40% DISCOUNT FOR BIS.
4.22.3 (Toy bicycles-Braking requirements- lever Length(l))	-	1250	40% DISCOUNT FOR BIS.
4.22.3 - 5.16.3(Toy bicycles-Braking requirements- brake performance for toy bicycles)	-	1250	40% DISCOUNT FOR BIS.
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of Plastic or wood ))	-	1200	40% DISCOUNT FOR BIS.
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy( Parts made of other materials))	-	1200	40% DISCOUNT FOR BIS.
4.25(Liquid-filled toys)	-	1000	40% DISCOUNT FOR BIS.
4.29(f) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.29(g) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	1500	40% DISCOUNT FOR BIS.
4.30.3 - 5.27 - 5.8(Toy scooters-Strength-dynamic strength for toy scooters- sharp-edge test)	-	1800	40% DISCOUNT FOR BIS.
4.30.3 - 5.27 - 5.9(Toy scooters-Strength-dynamic strength for toy scooters-sharp-point test)	-	1800	40% DISCOUNT FOR BIS.
4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes)	-	1200	40% DISCOUNT FOR BIS.
4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	1450	40% DISCOUNT FOR BIS.
4.30.5(b)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	1450	40% DISCOUNT FOR BIS.
4.30.5(c)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	1450	40% DISCOUNT FOR BIS.
4.30.5(d)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	1450	40% DISCOUNT FOR BIS.
4.30.5(e)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	1450	40% DISCOUNT FOR BIS.
4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs Diameter))	-	1450	40% DISCOUNT FOR BIS.
4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs space from end))	-	1450	40% DISCOUNT FOR BIS.
4.31.1 - 5.32(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-magnetic flux index)	-	1250	40% DISCOUNT FOR BIS.
4.31.1 - 5.2(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-small parts test)	-	1600	40% DISCOUNT FOR BIS.
4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index)	-	1250	40% DISCOUNT FOR BIS.
4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test)	-	1250	40% DISCOUNT FOR BIS.
4.31.2(b) - 5.34 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-soaking test for magnets-small parts test)	-	1200	40% DISCOUNT FOR BIS.
4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index After Following tests: -tension test for magnets; -drop test/tip over test for large and bulky toys; -torque test; -tension test, general procedure; -tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable; -impact test for magnets; -compression test; -tension test for magnets;)	-	1600	40% DISCOUNT FOR BIS.
4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test After Following tests: -tension test for magnets; -drop test/tip over test for large and bulky toys; -torque test; -tension test, general procedure; -tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable; -impact test for magnets; -compression test; -tension test for magnets;)	-	1600	40% DISCOUNT FOR BIS.
4.32 - 5.38.2( Yo-yo balls - length (lo) of the yo-yo ball tether)	-	1000	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.2 - 5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	1500	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.2(a) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-	1200	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.2(b) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-	1500	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.3 - 5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	1200	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.3 - 5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	1200	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.4 - 5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-	1500	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.4 - 5.3(Toys to be worn on the head-Full or partial moulded head masks-maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	1500	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	1800	40% DISCOUNT FOR BIS.
9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	1800	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	1800	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	1800	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-	1800	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame)	-	2000	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	2000	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	2000	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-rate of spread of flame )	-	1200	40% DISCOUNT FOR BIS.
9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-Test for soft-filled toys )	-	1200	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 )	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 )	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 )	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 )	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9)	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 )	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 )	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 3) 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9)	-	4500	40% DISCOUNT FOR BIS.
9873 (Part - 9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	6000	40% DISCOUNT FOR BIS.
9873 (Part - 9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	6000	40% DISCOUNT FOR BIS.
9873 (Part - 9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	6000	40% DISCOUNT FOR BIS.
9873 (Part - 9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	6000	40% DISCOUNT FOR BIS.
4.1(Normal use)	-	800	40% DISCOUNT FOR BIS.
4.3.1(Material quality)	-	1500	40% DISCOUNT FOR BIS.
5.24.6.1(Tension Test General procedure)	-	1200	40% DISCOUNT FOR BIS.

Complete

07 Aug, 2028

-
Excluding 5.13 Test for closures and Toy chest lids, 5.20 durability of mouth actuated toys

IS 9873 : Part 3 (2020)

Safety of Toys Part 3 Migration of Certain Elements ( Third Revision )

All type

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	562	NA
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	563	NA

Complete

07 Aug, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

UL India Private limited, Gurgaon

A-12 Sector 34 Infocity, Gurugram, Gurugram, Haryana, 122001

9560249888 Satish.Kumar@ul.com

Scope List