Cl.4.1
Fig. 1 to 3.(The three types shall be made to the shape and design as shown in
Fig. 1 to 3.) |
- |
200 |
|
18% GST Extra |
Cl 4.2.1, Table 1, Sr. No. 1(Solvent extractable substances) |
- |
500 |
|
18% GST Extra |
Cl 4.2.1, Table 1, Sr. No. 2(Chromium content, (as Cr₂O₃)) |
- |
650 |
|
18% GST Extra |
Cl 4.2.1, Table 1, Sr. No. 3(pH of aqueous extract) |
- |
300 |
|
18% GST Extra |
LP 8 Of IS 5914-1970(iv )Double hole stitch tear strength,kg/cm, Min) |
- |
600 |
|
18% GST Extra |
LP 10 IS 5914-1970(v) Shrinking temperature deg C) |
- |
300 |
|
18% GST Extra |
Cl .4.2.1( Leather - Chrome tanned/ chrome retanned full grain leather or
flesh splits manufactured from cow or buffalo hides conforming to the
following requirements shall be used
a) The leather and flesh split shall have thickness of 1.0 to 1.5 mm;) |
- |
200 |
|
18% GST Extra |
Cl .4.2.1(b) It shall be soft, pliable and free from flaws and loose fibres;) |
- |
200 |
|
18% GST Extra |
Cl .4.2.1(c)It shall be treated so as not to obscure defects and shall not be
stained with compounds of iron;) |
- |
200 |
|
18% GST Extra |
Cl .4.2.1(d) In case of grain leather, it shall not crack on the grain side when
bent grain outwards round a mandrel of 1.5 mm diameter through an angle of 180 degrees;) |
- |
200 |
|
18% GST Extra |
Cl .4.2.1(e)The leather shall not containt any chromate extractable by water
or dilute acids;) |
- |
200 |
|
18% GST Extra |
Cl .4.2.1(g ) For the hand part and the inner face of the cuff, the leather and
flesh split shall be of natural colour. The outer face of the cuff
and strengthening pieces may be printed and shall be of natural
shade or dyed to any shade as agreed to between the buyer and
the supplier;) |
- |
200 |
|
18% GST Extra |
Cl .4.2.1(h) The flesh side of leather shall be well buffed for type 2 and type 3) |
- |
200 |
|
18% GST Extra |
Cl 4.2.2(Cotton ,Polyamide cotton core spun or any other suitable thread shall be used.
core spun or any other For Type 1 material, the thread used
shall comply with the requirements given in co1 3 of Table 2. For
Type 2 and Type 3 materials, the thread shall comply with the
requirements given in co1 4 of Table 2. ) |
- |
200 |
|
18% GST Extra |
Cl.4.2.2, Table 2
IS 1670-1970(i) Length, m/kg, ) |
- |
100 |
|
18% GST Extra |
Cl.4.2.2, Table 2
IS 1670-1970(ii) Single thread breaking
load, Newtons,N) |
- |
500 |
|
18% GST Extra |
Cl.4.2.3, Table 3( Canvas - Cotton canvasj undyed, with the constructional particulars given in Table 3) |
- |
200 |
|
18% GST Extra |
Cl.4.2.3, Table 3(ii)Count of yarns ( approximate)
wrap ) |
- |
200 |
|
18% GST Extra |
Cl.4.2.3, Table 3(ii)Count of yarns ( approximate)
weft ) |
- |
200 |
|
18% GST Extra |
Cl.4.2.3, Table 3 IS 1963(iii)Ends/ cm) |
- |
100 |
|
18% GST Extra |
Cl.4.2.3, Table 3 IS 1963(iv)Picks/cm) |
- |
100 |
|
18% GST Extra |
Cl.4.2.3, Table 3 IS 1964(v)Mass, g/m2) |
- |
500 |
|
18% GST Extra |
Cl.4.2.3, Table 3(vi)Breaking load on 5 x 20 cm
ravelled strips, wrapway) |
- |
300 |
|
18% GST Extra |
Cl.4.2.3, Table 3(vi)Breaking load on 5 x 20 cm
ravelled strips, weftway) |
- |
300 |
|
18% GST Extra |
Cl.4.3.1.1(The dimensions are shown in Fig. 1 with tolerances as given in 4.1.1.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.1.2( The hand part shall be cut from the piece of undyed leather
and back portion including second, third and fourth fingers from
different pieces of undyed leather.) |
- |
300 |
|
18% GST Extra |
Cl. 4.3.1.3( The three different pieces of back portion shall be assembled
and stitched together along the edges by a row of stitches. The back
thus formed shall be secured with the corresponding front pieces ( palm
side ) of the fingers with a row of stitches. The thumb shall be made
from two pieces of undyed leather and closed with the hand part by a
seam. The seam of the thumb shall be reinforced by a strip of leather
and secured by two rows of stitches.) |
- |
500 |
|
18% GST Extra |
Cl 4.3.1.4( The hand part shall be made with the flesh side up and the
grain side to remain in contact with the hand.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.1.5( The cuff portion shall be made from two pieces of leather,
the inner portion being of leather, chrome tanned, natural colour and
the outer portion made of chrome tanned leather, with grain side out.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.1.6( Two pieces of leather shall be seemed together by a single
row of stitches on the finger side and two rows of stitches on the thumb
side. The cuff part thus formed shall be secured with the hand part by
two rows of stitches.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.1.7( A dyed leather piece cut to the shape of a semi-circle shall
be stitched on the inner part of the cuff along the joint of the hand and
the cuff portions by a single row of stitches as shown in Fig. 1. The
semi-circular piece of leather shall be not less than 75 mm in diameter.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.1.8( The gauntlets shall be machine stitched.) |
- |
100 |
|
18% GST Extra |
Cl.4.3.1.9( The number of stitches for all the stitchings shall be 6 to 8
stitches per 25) |
- |
100 |
|
18% GST Extra |
Cl.4.3.1.10(All losse ends of stitching threads shall be securely fastened) |
- |
200 |
|
18% GST Extra |
Cl.4.3.2.11( The number of stitches for all the stitchings shall be 6 to 8
stitches per 25 mm. All loose ends of stitching threads shall be securely
fastened.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.1 Type 3( The dimensions of mittens have been shown in Fig. 3 with
tolerances as given in 4.1.1. Other sizes of cuff length, if required, shall
be subject to agreement between the purchaser and the supplier.) |
- |
250 |
|
18% GST Extra |
Cl.4.3.3.2( The palm including the inner component of the compartment
for the four fingers shall be cut from one piece of leather and the
thumb from a separate piece.) |
- |
250 |
|
18% GST Extra |
Cl.4.3.3.3( The leather components shall be assembled with the flesh
side out, the grain side being inside.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.3.4( The back portion including the outer component of the
compartment for the four fingers shall be cut from one piece of canvas.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.5( The thumb shall be made with the two sides placed inside
and stitched with a row of stitches. The thumb thus formed shall be
attached to the palm through the cut hole and secured by two rows of
stitches.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.6 (The joint at the palm and the thumb shall be reinforced by
the same leather material and stitched by two rows of stitches as shown
in Fig. 3.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.7( The back portion made of canvas shall be secured with the
corresponding palm piece made of leather by two rows of stitches with
the edges of both the leather and canvas placed inside.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.8( The entire palm portion may be lined with canvas of the
same quality as used for the back, if required by the purchaser.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.9(The reinforcement
piece shall be placed flesh side out and secured by four rows of
stitches.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.10 (The cuff portion shall be made from one piece of canvas,
the side edges being stitched together with two rows of stitches with the
ends placed inside.) |
- |
250 |
|
18% GST Extra |
Cl.4.3.3.11( The cuff thus formed shall be secured to the hand part by two rows of stitches all along their edges and turned over subsequently.The bottom edges of the cuff shall be hemmed. 6.0 mm with the raw
edge properly,turned in.) |
- |
250 |
|
18% GST Extra |
Cl.4.3.3.12( The mittens shall be machine stitched.) |
- |
100 |
|
18% GST Extra |
Cl.4.3.3.13( The number of stitches for all stitchings shall be 6 to 8 stitches per 25 mm) |
- |
100 |
|
18% GST Extra |
Cl.4.3.3.14( All loose ends of stitching threads shall be securely fastened.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.3.15(workmanship and finish, and in all other respects not defined in this standard, the mittens shall conform to the approved sample.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.2.1 type 2( The dimensions of leather gauntlets for workers in iron and
steel industry have been shown in Fig. 2 with tolerances as given in 4.1.1.
Other sizes of cuff length, if required, shall be subject to agreement
between the purchaser and the supplier.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.2.2( The inner face of the gauntlets including the inner portion
of index, second, third and fourth fingers shall be cut from one piece of
leather. The thumb shall be cut from a separate piece of leather.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.2.3( The leather components shall be assembled with the flesh
side up, the grain side being inside.) |
- |
350 |
|
18% GST Extra |
Cl.4.3.2.4( The outer face of the gauntlets including index second, third
and fourth fingers shall be cut from one piece of canvas.) |
- |
350 |
|
18% GST Extra |
Cl.4.3.2.5( The thumb shall be made with the two cut sides placed
together and stitched with one row of stitches. The thumb thus formed
shall be attached to palm portion through the cut hole and secured by
two rows of stitches as shown in Fig. 2.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.2.6( The joint at the palm and the thumb shall be reinforced
with the same quality of leather as used for the inner face and stitched
by two rows of stitches.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.2.7( The back portion made of canvas shall be secured with the
corresponding palm piece made of leather by two rows of stitches with
the edges of both leather and canvas placed inside.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.2.8( A leather strip, 20 mm wide and of the same quality of
leather used for the inner face of the gauntlet, shall be used for reinforcing
the face of canvas over the knuckles. The reinforcement piece shall be
placed side up and secured by four rows of stitches.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.2.9( The cuff portion shall be made from one piece of canvas,
the side edges being stitched together by double row of stitches with the
ends placed inside. The cuff thus formed shall be secured to the hand
part by two rows of stitches with the edges of the material placed inside.
The bottom edge of the cuff shall be hemmed ( 6 mm ) with the row
edges properly turned in.) |
- |
300 |
|
18% GST Extra |
Cl.4.3.2.10( the gauntlets shall be machine stitched.) |
- |
200 |
|
18% GST Extra |
Cl.4.3.2.12(
Workmanship and finish, and in all other respects not defined in this standard, the gauntlets shall conform to the approved sample.) |
- |
300 |
|
18% GST Extra |