BIS - LIMS (Laboratory Information Management System)

(Derecognized) Pioneer Testing laboratory

Plot No:9/4, Street No: 4 , Mundka Industrial AreaNew Delhi - 110041, New Delhi, West, Delhi, 110041

9810040186 pioneertestinglab@gmail.com

Scope List

Reset

72 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

All

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.b(Potyethylene - anti-oxidant)	-	2500	-
4.1.c.i (Density)	-	500	-
4.1.c.ii (Toluene extract - Annex A)	-	2000	-
4.1.c.iii (Volatile matter - Annex B )	-	1000	-
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	1000	-
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	1000	-
7.3(Tensile Test)	-	750	-
7.3(Elongation at Break)	-	400	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1500	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	300	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	300	-
7.2(Reversion Test)	-	1000	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	300	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	300	-
7.2(Reversion Test)	-	1000	-
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	300	-
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	300	-
7.2(Reversion Test)	-	1000	-
7.1(Hydraulic Characteristics)	-	4000	-
7.1(Hydraulic Characteristics)	-	4000	-
6.1(Visual Appearance)	-	350	-
3.1(Class of Pipe)	-	4000	-
9.0 (9.1)(Minimum Internal Diameter of Coil)	-	300	-
7.1 Table-2 (b)Acceptance Test for 01 hour at 20°C & 6.9MPa induced stress)	-	2000	-
7.1 Table-2 (Hydraulic Characteristics a)Quality Test for 100 hours at 70°C & 2.5.MPa induced stress. )	-	2000	-
6.0 (6.1) (Visual appearance)	-	350	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Maximum)	-	300	-
5.0 5.1 (Table1) (c)Wall thickness of pipe Minimum)	-	300	-
5.0 5.1 (Table1) (b)Tolerance on OD)	-	300	-
5.0 5.1 (Table1) (Dimensions a)Outside diameter of pipe)	-	300	-

-
-

IS 617 (1994)

Cast aluminium and its alloys - Ingots and castings for general engineering purposes - Specification (Third Revision)

All

4700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(TOLERANCES ON DIMENSIONS OF CASTINGS)	-	500	-
7(FREEDOM FROM DEFECTS)	-	300	-
6.2(Hardness)	-	750	-
6, Table 2.(MECHANICAL PROPERTIES OF CASTINGS)	-	1400	-
5, Table 1.(Chemical Composition)	-	3300	-
15.4 (b)(Cold impact)	-	1000	-
9.1(PIPE ENDS)	-	0	-

-
-

IS 738 (1994)

Wrought aluminium alloys, drawn tube for general engineering purposes - Specification (Third Revision)

All

5600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6(Freedom from Defects- Cl.6)	-	500	-
Cl.7, IS 2678(Wall Thickness at any point)	-	500	-
Cl.7, IS 2678(Mean Wall Thickness)	-	500	-
Cl.7, IS 2678(Straightness)	-	500	-
Cl. 9.1 Table 2(0.2 percent proof stress- IS 2657)	-	500	-
Cl. 9.1 Table 2(Tensile Strength- IS 2657)	-	600	-
Cl. 9.1 Table 2(Elongation on guage length of 50 mm)	-	400	-
Cl. 9.1.2(Flattening Test- IS 2328)	-	500	-
Cl. 8.1, Table 1(Aluminium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Copper- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Magnesium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Silicon- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Iron- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Manganese- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Zinc- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Titanium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Chromium- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 1(Ti+ V (Remarks)- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 2(T. I.(Remarks)- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 3(Ti+ Cr (Remarks)- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-
Cl. 8.1, Table 4(Cr+ Mn (Remarks)- IS 504 : 1963 or 1S 11085 : 1984 or any other established instrumental/chemical method. )	-	300	-

-
-

IS 3564 (1995)

Hydraulically Regulated Door Closers -Specification

All

7050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11(Marking)	-	200	-
11(Marking)	-	200	-
11(Marking)	-	200	-
11(Marking)	-	200	-
11(Marking)	-	200	-
11(Marking)	-	200	-
11(Marking)	-	200	-
12(Packing)	-	200	-
12(Packing)	-	200	-
12(Packing)	-	200	-
12(Packing)	-	200	-
12(Packing)	-	200	-
12(Packing)	-	200	-
6(Nominal Sizes)	-	500	-
6(Nominal Sizes)	-	500	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
8(Essential Requirements)	-	450	-
9(Finish)	-	500	-
9(Finish)	-	500	-
9(Finish)	-	500	-
9(Finish)	-	500	-
9(Finish)	-	500	-
9(Finish)	-	500	-
9(Finish)	-	500	-
9(Finish)	-	500	-
9(Finish)	-	500	-
10Annex B(Test)	-	2500	-
B-1.2(a) Visual Inspection)	-	500	-
B-1.3(b) Surface)	-	500	-
B-1.3(b) Surface)	-	500	-
B-1.4(c) Performance Requirements)	-	500	-
B-1.4(c) Performance Requirements)	-	500	-
B-1.4(c) Performance Requirements)	-	500	-
B-1.4(c) Performance Requirements)	-	500	-
B-1.5(d) Endurance Test)	-	1000	-
B-1.5(d) Endurance Test)	-	1000	-
B-1.5(d) Endurance Test)	-	1000	-
B-1.5(d) Endurance Test)	-	1000	-
B-1.5(d) Endurance Test)	-	1000	-
B-1.5(d) Endurance Test)	-	1000	-
Cl. 7 Table 2(Materials)	-	7050	-

-
-

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

All

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 7(Workmanship)	-	500	-
Cl 6(Workmanship)	-	500	-
Cl 9.1 & Table 3(Diameter & Out Of Round)	-	300	-
Cl 10(UTM)	-	1500	-
Table 7(Workmanship)	-	500	-
Cl 6(Workmanship)	-	500	-
Cl 9.1 & Table 3(Diameter & Out Of Round)	-	300	-
Table 7(Workmanship)	-	500	-
Cl 6(Workmanship)	-	500	-
Cl 9.1 & Table 3(Diameter & Out Of Round)	-	300	-
Cl 10(UTM)	-	1500	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nitrogen)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Titanium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Vanadium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Boron)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Copper)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Molybdenum)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nickel)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Chromium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Aluminium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Silicon)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Manganese)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Phosphorous)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Sulphor)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Carbon)	-	300	-

-
-

IS 1328 (1996)

Veneered Decorative Plywood -Specification

All

2850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Grade - For BWR)	-	200	-
4.1(Grade - For MR)	-	200	-
4.2(Type - For Type 1)	-	200	-
4.2(Type - For Type 2)	-	200	-
7.1.1(Requirements - Open splits, checks or open joints - For Type 1 - Cl. 7.1.1)	-	200	-
7.2.1(Requirements - Open splits, checks or open joints - For Type 2 - Cl. 7.2.1)	-	200	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	200	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	200	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	200	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	300	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	300	-
9(Finish - Cl. 9.1, 8.3)	-	500	-
9(Finish - Cl. 9.2, 8.3)	-	500	-
11(Tests - Moisture Content - Part 1 of IS 1734)	-	400	-
11(Tests - Water Resistance Test - Cl. 11.1.2.1 [for MR Grade])	-	750	-
11(Tests - Water Resistance Test - Cl. 11.1.2.2 [for BWR Grade])	-	750	-

-
-

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

All Type

19900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Colour)	-	200	-
7(Visual Appearance)	-	200	-
6(Dimensions of pipes)	-	1000	-
8.1(Hydraulic characteristics)	-	12500	-
8.2(Reversion)	-	1500	-
8.3(Density)	-	500	-
8.4(Melt Flow Rate)	-	1000	-
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	1000	-

-
-

IS 14587 (1998)

Prelaminated Medium Density Fibre Board -specification

All

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Dimensions and tolerances)	-	1850	-
10.2, Table-1(Test for Density)	-	500	-
10.4, Table-1(Test for Water Absorption)	-	750	-
10.5(test for swelling in water)	-	1000	-
10.6(test for modulis of rupture)	-	1500	-
10.7(Test for tensile strength perpendicular to Surface)	-	1000	-
10.8(Test for tensile strength perpendicular to Surface after ageing )	-	1000	-
10.9(test screw withdrawal strength)	-	1000	-
10.1(test for surface abrasion resistance)	-	1000	-
10.11(test for resistance to steam)	-	1200	-
10.12(test for resistance to crack)	-	1200	-
10.13(test for resistance to cigarette burn)	-	1200	-
10.14(test for resistance to stain)	-	1200	-

-
-

IS 3444 (1999)

Corrosion resistant high alloy steel and nickel base castings for general applications - Specification (Third Revision)

All

9950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(MECHANICAL TESTS)	-	5750	-
10(FREEDOM FROM DEFECTS)	-	500	-
9(WORKMANSHIP AND FINISH)	-	500	-
8, Table 1.(CHEMICAL COMPOSITION)	-	4200	-

-
-

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

All

8550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3(CLASSIFICATION OF PIPES)	-	200	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1200	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	500	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1200	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
4.3(Anti-oxidant)	-	2500	-
5.1 table -1(DIMENSIONS OF PIPES)	-	900	-
5.1.2(Ovality)	-	500	-
6.1(VISUAL APPEARANCE)	-	300	-
7.1 Table -2(Hydraulic Characteristics)	-	1500	-
7.2(Reversion Test)	-	1000	-
7.3(Tensile Test)	-	750	-
7.4table-2(Fusion Compatibility Test)	-	1500	-
7.5(Density)	-	500	-
7.6(Melt now Rate (MFR))	-	1200	-
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	1000	-
(Cl.4.2)(Carbon black- a)carbon content)	-	1000	-
Cl.7.6(Melt Flow Rate)	-	1200	-
Cl.7.4(Fusion Compatibility Test- b) Acceptance test)	-	750	-
Cl.7.4(Fusion Compatibility Test- a) Quality test)	-	750	-
Cl.7.3(Tensile Test - ii)Elongation at Break)	-	400	-
Cl.7.3(Tensile Test- i) Tensile Strength)	-	750	-
Cl.7.2)(Reversion Test)	-	1000	-
Cl 7.1(Hydraulic Characteristics - Acceptance test)	-	750	-
Cl 7.1(Hydraulic Characteristics - Quality test)	-	750	-
Cl.6(Visual Appearance)	-	300	-
Cl.5(Dimensions of pipe - ii) Wall thickness maximum)	-	200	-
Cl.5(Dimensions of pipe - ii) Wall thickness minimum)	-	200	-
Cl.5(Dimensions of pipe - i) Outside diameter)	-	200	-
15.4 (b)(Cold impact)	-	1000	-

-
-

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

All

22700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type of Fitting)	-	200	-
4(Size Designation)	-	500	-
5(Colour of fittings)	-	200	-
7.1,Table 1(Wall thickness)	-	200	-
7.2 ,Table 2&3(Socket Dimensions)	-	200	-
7.3(Dimensions of waste trap(Nahani Trap)	-	750	-
8(Sealing Rings)	-	750	-
10(Workmanship)	-	750	-
11(Design requirements)	-	750	-
11.1(Solvent cement type or Rubber ring type)	-	1500	-
11.2(Socket and spigot configeration)	-	2000	-
11.4,Table 5(Vent cowl)	-	3500	-
11.5,Table 6(Pipe Clips)	-	2500	-
12(Physical test requirements)	-	3500	-
12.1(Visual appearance)	-	200	-
12.2(Stress relief test)	-	2000	-
12.3(Vicat softening tempewrature)	-	1500	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	1200	-
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1500	-
Cl.15, Annex B(Sulphated Ash Content)	-	1200	-
16(Mechanical Properties)	-	1000	-
16.1(Impact test)	-	1500	-
17(Watet tightness of joint)	-	1500	-

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

All Type

19100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	1200	-
8.5 (Oxidation Induction Time)	-	1500	-
8.9 table-6(Elongation at Break)	-	750	-
8.8(Tensile Strength for Butt-fusion)	-	750	-
8.7(Density)	-	500	-
8.4( Melt Flow Rate)	-	1000	-
8.2(Longitudinal Reversion Test)	-	1500	-
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1200	-
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	4000	-
7.4.1.2(Ovality)	-	250	-
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	200	-
7.2(Length)	-	200	-
6.2.1(6.1.1 Identification Stripes)	-	450	-
8.6(Overall migration)	-	1500	-
8.3(Carbon black)	-	1000	-
5.3(e)(Carbon Black Master Batch)	-	10000	-
5.2(Polyethylene Resin)	-	10000	-
5.4(Anti oxydent)	-	2500	-
5, 5.1 table-1(MATERIALS)	-	10000	-
6.2(Colour)	-	500	-

-
-

Bureau of Indian Standards

The National Standards Body of India

(Derecognized) Pioneer Testing laboratory

Plot No:9/4, Street No: 4 , Mundka Industrial AreaNew Delhi - 110041, New Delhi, West, Delhi, 110041

9810040186 pioneertestinglab@gmail.com

Scope List