BIS - LIMS (Laboratory Information Management System)

WELL TECH TEST AND RESEARCH CENTER, DERABASSI

INDUSTRIAL BLOCK -B , VILLAGE SAIDPURA, DERABASSI, MOHALI, S.A.S Nagar, Punjab, 140507

7973565868 wtechresearch@gmail.com

Scope List

Reset

100 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

TYPE &TYPE B/ Class 1-6 & Plumbing Pipe/ OD 20mm-315mm

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300	-
10.1(Surface Finish)	-	300	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	300	-
10.7(Sulphated Ash Content)	-	750	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	750	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	200	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	200	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	200	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	200	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	200	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	300	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	300	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	300	-
7.2.1(DIMENSIONS-Socket)	-	400	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	300	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	300	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	350	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	300	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	-
8(SEALING RINGS)	-	250	-
9.1(PIPE ENDS)	-	250	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	750	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	750	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	1000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	1000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	500	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	500	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	500	-
11.2(Resistance to External Blows at 0°C)	-	1500	-
10.3(Effect on Water Test)	-	2500	-
5(CLASSIFICATION OF PIPES)	-	2500	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	300	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	300	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	300	-
7.1.4(Length)	-	500	-
7.2.1.2b(Maximum inner diameter of groove)	-	500	-
13.1(Marking)	-	250	-
cL-13.1.1(Marking)	-	250	-
Cl-13.1.2(Marking)	-	250	-
10.1(Colour)	-	300	-
10.1(Surface Finish)	-	300	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	300	-
10.7(Sulphated Ash Content)	-	750	-
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	750	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	200	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	200	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	200	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	200	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	200	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	300	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	300	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	300	-
7.2.1(DIMENSIONS-Socket)	-	400	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	300	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	300	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	350	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	300	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	-
8(SEALING RINGS)	-	250	-
9.1(PIPE ENDS)	-	250	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	500	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	750	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	750	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	1000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	1000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	500	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	500	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	500	-
11.2(Resistance to External Blows at 0°C)	-	1500	-
10.3(Effect on Water Test)	-	2500	-
5(CLASSIFICATION OF PIPES)	-	2500	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	300	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	300	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
7.1.3(mean outside diameter, outside diameter at any point, and wall thickness of plumbing pipes)	-	300	-
7.1.4(Length)	-	500	-
7.2.1.2b(Maximum inner diameter of groove)	-	500	-
13.1(Marking)	-	250	-
cL-13.1.1(Marking)	-	250	-
Cl-13.1.2(Marking)	-	250	-

30 Mar, 2027

-
-

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

SIZE UPTO 20-315 DN TYPE A TYPE B

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	13000	-
Cl.7.1(Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-	13000	-
Cl.7.1(Wall thickness "minimum,maximum" (Take 8 reading))	-	13000	-
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	13000	-
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	13000	-
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	13000	-
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	13000	-
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	13000	-
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	13000	-
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	13000	-
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	13000	-
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	13000	-
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	13000	-
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	13000	-
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	13000	-
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	13000	-
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	13000	-
8.6(Effect on Water Test)	-	13000	-
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	13000	-
14(Marking)	-	13000	-

30 Mar, 2027

-
-

IS 210 (2009)

Grey iron castings - Specification (First Revision)

AS PER TABLE 3 AND CL 4

6000 View breakup
The testing charges quoted by the laboratory exceed 1.5 times the government-approved rate. Therefore, in accordance with LRS 2020, the testing charges are being capped at 1.5 times the BIS lab.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	749.99	-
7.1(WORKMANSHIP AND FINISH)	-	499.99	-
10.1(FREEDOM FROM DEFECTS)	-	999.99	-
10.2(FREEDOM FROM DEFECTS)	-	999.99	-
13(SIZE OF TEST BARS-Diameter)	-	499.99	-
13(SIZE OF TEST BARS-Length)	-	499.99	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	2000	-
16, Table 3(Hardness Test)	-	1999.99	-
17,Annex B(TRANSVERSE TEST)	-	1000	-
18(HYDROSTATIC TEST)	-	499.99	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	0	-
7.1(WORKMANSHIP AND FINISH)	-	0	-
10.1(FREEDOM FROM DEFECTS)	-	0	-
10.2(FREEDOM FROM DEFECTS)	-	0	-
13(SIZE OF TEST BARS-Diameter)	-	0	-
13(SIZE OF TEST BARS-Length)	-	0	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	0	-
16, Table 3(Hardness Test)	-	0	-
17,Annex B(TRANSVERSE TEST)	-	0	-
18(HYDROSTATIC TEST)	-	0	-
9(IS 7754)	-	1999.98	-
9(IS 7754)	-	0	-
9(Microstructure)	-	1999.99	-
21(Marking)	-	250	-
9(Microstructure)	-	0	-
7.2(Casting dimensions)	-	499.99	-
Cl-6(Phosprorus (P) - IS 12308 ( P-5))	-	0	-

30 Mar, 2027

-
-

IS 4035 (1967)

Specification for trolleys, stretcher

AS PER FIG 1

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Frame Work)	-	2000	-
2.2(Hoops)	-	2000	-
2.3(Castors)	-	1500	-
3(Dimensions)	-	2000	-
4(Manufacture)	-	1000	-
5(Finish)	-	1000	-
6(Adhesion Test)	-	1000	-
7(Marking)	-	500	-
8(Packing)	-	500	-

30 Mar, 2027

-
-

IS 3829 : Part 3 (1985)

Specification for steam sterilizers: Part 3 pressure sterilizers, vertical cylindrical type

DESIGN AS PER CL 3 , SHAPE AND SIZE AS PER CL 4

11304 View breakup
The testing charges quoted by the laboratory exceed 1.5 times the government-approved rate. Therefore, in accordance with LRS 2020, the testing charges are being capped at 1.5 times the BIS lab.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Shape)	-	1000	-
4.2(Size)	-	500	-
5.1(Carbon- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Silicon- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Manganese- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Nickel- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Chromium- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Sulphur- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Phosphorous- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Nitrogen- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Titanium- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Niobium- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	250	-
5.1(Molybdenum- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(Copper- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	200	-
5.1(As per IS 306 or IS 318- Relevant parts of IS 4027 or any other established instrumental/Chemicall method)	-	2500	-
5.1(As per IS 513- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	2000	-
5.1(As per IS 737- Relevant parts of IS 504 or any other established instrumental/Chemicall method)	-	2000	-
6.1(as per Cl. 6.1)	-	500	-
6.1.2(Shell)	-	500	-
6.1.3(as per Cl. 6.1.3)	-	500	-
6.2(Lid)	-	1000	-
6.3(Lid Gasket)	-	1000	-
7.1.2(Safety Valve- Cl. 7.1.2)	-	1000	-
7.1.3(as per Cl. 7.1.3)	-	2000	-
7.1.4(as per Cl. 7.1.4)	-	2000	-
8.1(Hydrostatic Test- as per Cl 8.1.1)	-	5000	-
3(Design)	-	500	-
4(Shape & Size)	-	2000	-
5(Materials)	-	2000	-
6(Construction)	-	2500	-
7(Fittings)	-	2500	-
8(Hydrostatic test)	-	0	REPEAT
8(Methods of steam supply to sterilizer)	-	5000	-
9.1(Safety Requirements)	-	10000	-
9.1(Power Supply &Input)	-	5000	-
9.1("Leakage Current and Electric Strength at operating temperature")	-	5000	-
9.1(Provision for Earthing)	-	5000	-
9.1(Creepage Distance and Clearance)	-	5000	-
10(Accessories)	-	1000	-
10(Marking)	-	1000	-
13(Packing)	-	1000	-
4.1(Shape)	-	0	-
4.2(Size)	-	0	-
5.1(Carbon- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Silicon- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Manganese- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Nickel- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Chromium- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Sulphur- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Phosphorous- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Nitrogen- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Titanium- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Niobium- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Molybdenum- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(Copper- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(As per IS 306 or IS 318- Relevant parts of IS 4027 or any other established instrumental/Chemicall method)	-	0	-
5.1(As per IS 513- Relevant parts of IS 228 or any other established instrumental/Chemicall method)	-	0	-
5.1(As per IS 737- Relevant parts of IS 504 or any other established instrumental/Chemicall method)	-	0	-
6.1(as per Cl. 6.1)	-	0	-
6.1.2(Shell)	-	0	-
6.1.3(as per Cl. 6.1.3)	-	0	-
6.2(Lid)	-	0	-
6.3(Lid Gasket)	-	0	-
7.1.2(Safety Valve- Cl. 7.1.2)	-	0	-
7.1.3(as per Cl. 7.1.3)	-	0	-
7.1.4(as per Cl. 7.1.4)	-	0	-
8.1(Hydrostatic Test- as per Cl 8.1.1)	-	0	-
3(Design)	-	0	-
4(Shape & Size)	-	0	-
5(Materials)	-	0	-
6(Construction)	-	0	-
7(Fittings)	-	0	-
8(Hydrostatic test)	-	0	-
8(Methods of steam supply to sterilizer)	-	0	-
9.1(Safety Requirements)	-	0	-
9.1(Power Supply &Input)	-	0	-
9.1("Leakage Current and Electric Strength at operating temperature")	-	0	-
9.1(Provision for Earthing)	-	0	-
9.1(Creepage Distance and Clearance)	-	0	-
10(Accessories)	-	0	-
10(Marking)	-	0	-
13(Packing)	-	0	-

30 Mar, 2027

-
-

IS 3829 : Part 1 (1999)

Specification for steam sterilizers: Part 1 horizontal cylindrical and horizontal rectangular steam sterilizers, pressure type (For Hospital And Pharmaceutical Use) (Second Revision)

SHAPE AND SIZE AS PER CL 5, TABLE 1 AND TABLE WITH FIGURE 1 AND 2

11310 View breakup
The testing charges quoted by the laboratory exceed 1.5 times the government-approved rate. Therefore, in accordance with LRS 2020, the testing charges are being capped at 1.5 times the BIS lab.

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Design)	-	2000	-
Cl. 5 - Table 1 & 2(Shape & Size)	-	5000	-
Cl. 7(Construction)	-	15000	-
Cl. 8(Fittings)	-	15000	-
Cl. 9(Hydrostatic test)	-	5000	-
Cl. 9(Hydrostatic test)	-	0	-
Cl. 9(Hydrostatic test)	-	0	-
Cl. 10(Method of stem supply to Sterilizer)	-	5000	-
Cl. 10.8(Capacity)	-	5000	-
6.1, 6.2(Chamber)	-	5000	-
6.1, 6.2(Jacket)	-	5000	-
6.1 and 6.2(Other)	-	2000	-
4(Design)	-	0	-
5(Shape & Size)	-	0	-
6(Materials)	-	2000	-
7(Construction)	-	0	-
8(Fittings)	-	0	-
9(Hydrostatic test)	-	0	-
10(Methods of steam supply to sterilizer)	-	0	-
11(Accessories)	-	5000	-
12(Marking)	-	2000	-
Cl. 4(Design)	-	0	-
Cl. 5 - Table 1 & 2(Shape & Size)	-	0	-
Cl. 7(Construction)	-	0	-
Cl. 8(Fittings)	-	0	-
Cl. 9(Hydrostatic test)	-	0	-
Cl. 9(Hydrostatic test)	-	0	-
Cl. 9(Hydrostatic test)	-	0	-
Cl. 10(Method of stem supply to Sterilizer)	-	0	-
Cl. 10.8(Capacity)	-	0	-
6.1, 6.2(Chamber)	-	0	-
6.1, 6.2(Jacket)	-	0	-
6.1 and 6.2(Other)	-	0	-
4(Design)	-	0	-
5(Shape & Size)	-	0	-
6(Materials)	-	0	-
7(Construction)	-	0	-
8(Fittings)	-	0	-
9(Hydrostatic test)	-	0	-
10(Methods of steam supply to sterilizer)	-	0	-
11(Accessories)	-	0	-
12(Marking)	-	0	-

30 Mar, 2027

-
Included w.e.f 10.04.2026

IS 3099 : Part 1 AND 2 (1992)

Microscopes - Slips and slidesspecification: Part 1 microscope slips: Part 2 microscope slides (First Revision)

DIMENSIONS AS PER CLAUSE 3 (GENERAL PURPOSE , HIGH PERFORMANCE AND MICROSCOPE SLIDES)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
(Cl.7)(Edge Quality )	-	1000	-
(Cl.5.1 (Surface Finish )	-	1000	-
(CL.4)(Visible Seed )	-	1000	-
Cl 3(General purpose High performance )	-	500	-
Cl 3(General purpose High performance )	-	500	-
Cl 3(General purpose High performance )	-	500	-
Cl 3(General purpose High performance )	-	500	-
Cl 3(General purpose High performance )	-	500	-
Cl 3(General purpose High performance )	-	500	-
Cl 3(Dimensions Thickness)	-	500	-
Cl 3(Dimensions Thickness)	-	500	-
Cl 3(Dimensions Thickness)	-	500	-
Cl 3(Dimensions Thickness)	-	500	-
Cl 3(Dimensions Thickness)	-	500	-
Cl 3(Dimensions Thickness)	-	500	-
Cl 3(Dimensions width)	-	500	-
Cl 3(Dimensions width)	-	500	-
Cl 3(Dimensions width)	-	500	-
Cl 3(Dimensions width)	-	500	-
Cl 3(Dimensions width)	-	500	-
Cl 3(Dimensions width)	-	500	-
Cl 3(Dimensions length )	-	500	-
Cl 3(Dimensions length )	-	500	-
Cl 3(Dimensions length )	-	500	-
Cl 3(Dimensions length )	-	500	-
Cl 3(Dimensions length )	-	500	-
Cl 3(Dimensions length )	-	500	-
Cl 3(Dimensions )	-	500	-
Cl.2(Material)	-	5000	-
(Cl.5.2)(Edge Quality )	-	0	-
(Cl.5.1 (Surface Finish )	-	0	-
(CL.4)(Visible Seed )	-	0	-
Cl 3(General purpose High performance )	-	0	-
Cl 3(General purpose High performance )	-	0	-
Cl 3(General purpose High performance )	-	0	-
Cl 3(General purpose High performance )	-	0	-
Cl 3(General purpose High performance )	-	0	-
Cl 3(General purpose High performance )	-	0	-
Cl 3(Dimensions Side -22 )	-	0	-
Cl 3(Dimensions Side -22 )	-	0	-
Cl 3(Dimensions Side -22 )	-	0	-
Cl 3(Dimensions Side -22 )	-	0	-
Cl 3(Dimensions Side -22 )	-	0	-
Cl 3(Dimensions Side -22 )	-	0	-
Cl 3(Dimensions Side -22 )	-	0	-
Cl 3(Dimensions Side -22 Thickness)	-	0	-
Cl 3(Dimensions Side -22 Thickness)	-	0	-
Cl 3(Dimensions Side -22 Thickness)	-	0	-
Cl 3(Dimensions Side -22 Thickness)	-	0	-
Cl 3(Dimensions Side -22 Thickness)	-	0	-
Cl 3(Dimensions )	-	0	-
Cl.2(Material)	-	0	-

30 Mar, 2027

-
Included w.e.f 10.04.2026

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

SIZE 16 MM, 20 MM, 25 MM, 32 MM, 40 MM

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	4000	-
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	4000	-
6.3(Standard Mark on Conduit)	-	4000	-
7.1.1(Maximum and minimum outside diameter of socket)	-	4000	-
7.1.1 Table-2(Length of Socket end)	-	4000	-
7.1.2(Maximum and minimum outside diameter of conduit)	-	4000	-
7.2(Minimum inside diameter of conduit)	-	4000	-
7.3(Length of conduit)	-	4000	-
7.4(Unifomity of The wall Thickness)	-	4000	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	4000	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	4000	-
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	4000	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	4000	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	4000	-
10(Resistance to Heat -Ball presure test)	-	4000	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	4000	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	4000	-
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	4000	-
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	4000	-
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	4000	-
12(3 Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	4000	-
12(3 Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	4000	-
11.0(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	4000	-
10.0(Resistance to Heat -Ball presure test)	-	4000	-
9.5 Fig.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	4000	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	4000	-
9.3(Compression Test (after removal of force) as per caluse 9.3.3 of IS: 9537 (Part 1)-1980)	-	4000	-
9.3(Compression Test at Full force applied (On load))	-	4000	-
9.2(Bending Test At Low Temp (-5 ±2°C))	-	4000	-
9.2(Bending Test At Room Temp)	-	4000	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	4000	-
7.4(Unifomity of The wall Thickness)	-	4000	-
7.3(Length of conduit)	-	4000	-
7.2 Fig.3(Minimum inside diameter of conduit)	-	4000	-
7.1.2 Fig.2(Minimum outside diameter of conduit)	-	4000	-
7.1.2 Fig.1(Maximum outside diameter of conduit)	-	4000	-
7.1.1 Table-2(Length of Socket end)	-	4000	-
7.1.1 Fig.8(Maximum inside diameter of socket)	-	4000	-
7.1.1 Fig.7(Maximum outside diameter of socket)	-	4000	-
6.3(Standard Mark on Conduit)	-	4000	-
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	4000	-
6.1 - d(Marking)	-	4000	-
6.1 - c(Marking)	-	4000	-
6.1 - b(Marking)	-	4000	-
6.1 - a(Marking)	-	4000	-

30 Mar, 2027

-
-

IS 1381 : Part 2 (2019)

Laboratory glassware - Boiling flasks: Part 2 boiling flasks with conical ground joints (Third Revision)

AS PER TABLE 1-3

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type)	-	1000	-
4(Series of capacities)	-	1000	-
5(Material)	-	1000	-
5(Material)	-	1000	-
6(Dimensions)	-	4000	-
6(Dimensions)	-	2000	-
6(Dimensions)	-	2000	-
6(Dimensions)	-	2000	-
7(Ground glass joints)	-	1000	-
8(Thermal shock endurance)	-	3500	-
9(Marking)	-	500	-
9(Marking)	-	500	-
9(Marking)	-	500	-
9(Marking)	-	500	-
3(Type)	-	0	-
4(Series of capacities)	-	0	-
5(Material)	-	0	-
5(Material)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
7(Ground glass joints)	-	0	-
8(Thermal shock endurance)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	0	-
3(Type)	-	0	-
4(Series of capacities)	-	0	-
5(Material)	-	0	-
5(Material)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
6(Dimensions)	-	0	-
7(Ground glass joints)	-	0	-
8(Thermal shock endurance)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	0	-
9(Marking)	-	200	-
9(Marking)	-	0	-

30 Mar, 2027

-
-

IS 4948 (2020.0)

Welded steel wire fabric for general use - Specification (Second Revision)

AS PER ANNEX A

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.1(MATERIALS)	-	1500	-
Cl. 4.2(MATERIALS)	-	1500	-
Cl. 5.1(MANUFACTURE OF MESH (Assembling of Wires))	-	500	-
Cl. 5.2(MANUFACTURE OF MESH)	-	500	-
Cl. 5.3(MANUFACTURE OF MESH)	-	500	-
Cl. 5.4(Spacing of Longitudinal and Transverse Wires)	-	1000	-
Cl. 5.5(Tolerance of Size of Mesh)	-	1000	-
Cl. 5.6(Tolerance of Size of Sheet or Roll)	-	1000	-
Cl. 6(TEST FOR WELDING)	-	4000	-
Cl. 9.1(Marking)	-	200	-
Cl. 9.1(Marking)	-	200	-
Cl. 9.1(Marking)	-	200	-
Cl. 9.1(Marking)	-	200	-
Cl. 9.1(Marking)	-	200	-
Cl. 9.1(Marking)	-	200	-
Cl. 9.1(Marking)	-	200	-
Cl. 9.3(BIS Certification Marking)	-	200	-
Cl. 10.1(Finish)	-	1000	-
Cl. 4.1(MATERIALS)	-	0	-
Cl. 4.2(MATERIALS)	-	0	-
Cl. 5.1(MANUFACTURE OF MESH (Assembling of Wires))	-	0	-
Cl. 5.2(MANUFACTURE OF MESH)	-	0	-
Cl. 5.3(MANUFACTURE OF MESH)	-	0	-
Cl. 5.4(Spacing of Longitudinal and Transverse Wires)	-	0	-
Cl. 5.5(Tolerance of Size of Mesh)	-	0	-
Cl. 6(TEST FOR WELDING)	-	0	-
Cl. 5.6(Tolerance of Size of Sheet or Roll)	-	0	-
Cl. 4.1(MATERIALS)	-	0	-
Cl. 4.2(MATERIALS)	-	0	-
Cl. 5.1(MANUFACTURE OF MESH (Assembling of Wires))	-	0	-
Cl. 5.2(MANUFACTURE OF MESH)	-	0	-
Cl. 5.3(MANUFACTURE OF MESH)	-	0	-
Cl. 5.4(Spacing of Longitudinal and Transverse Wires)	-	0	-
Cl. 5.5(Tolerance of Size of Mesh)	-	0	-
Cl. 5.6(Tolerance of Size of Sheet or Roll)	-	0	-
Cl. 6(TEST FOR WELDING)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.3(BIS Certification Marking)	-	0	-
Cl. 10.1(Finish)	-	0	-
Cl. 4.1(MATERIALS)	-	0	-
Cl. 4.2(MATERIALS)	-	0	-
Cl. 5.1(MANUFACTURE OF MESH (Assembling of Wires))	-	0	-
Cl. 5.2(MANUFACTURE OF MESH)	-	0	-
Cl. 5.3(MANUFACTURE OF MESH)	-	0	-
Cl. 5.4(Spacing of Longitudinal and Transverse Wires)	-	0	-
Cl. 5.5(Tolerance of Size of Mesh)	-	0	-
Cl. 5.6(Tolerance of Size of Sheet or Roll)	-	0	-
Cl. 6(TEST FOR WELDING)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.1(Marking)	-	0	-
Cl. 9.3(BIS Certification Marking)	-	0	-
Cl. 10.1(Finish)	-	0	-

30 Mar, 2027

-
-

IS 9375 (1979)

Precast Reinforced Concrete Plant Guards

fig 1

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Uniform Thickness)	-	2500	-
4.2(Tolerance)	-	2500	-
4.3(Minimum Dimensions)	-	3000	-
5(Finish)	-	3000	-
6(Erection and Fixing)	-	2500	-
7.1(Static load Test)	-	5000	-
9(Marking)	-	1000	-

30 Mar, 2027

-
Included w.e.f 16.12.2025 Exclusion: Raw material

IS 5758 (2020)

Precast Concrete Kerbs, Channels, Edging, Quadrants and Other Associated Fittings - Specification ( Second Revision )

AS PER Table 1 and 2 ( FIG 1 -12)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Shape and Dimensions)	-	25000	-
4.4(Manufacturing of Units)	-	1000	-
4.5(Units with Special Faces)	-	1000	-
4.6(End Treatment)	-	1000	-
5(Designation and Size)	-	2500	-
6.2(Deviations on Flatness and Straightness)	-	1500	-
7.2.1(Fine and coarse aggregates)	-	1000	-
7.1(Cement)	-	500	-
7.2.2(The maximum size of coarse aggregates)	-	500	-
7.3(Pulverized Fuel Ash)	-	500	-
9.1(General)	-	1000	-
9.2(Dimensions)	-	1000	-
9.3(Bending Strength)	-	2500	-
9.4(Water Absorption)	-	2500	-
15(Marking)	-	500	-

30 Mar, 2027

-
Included w.e.f 16.12.2025 Exclusion: Raw material

IS 12817 (2020)

Stainless Steel Butt Hinges - Specification ( Third Revision )

SIZE 50-150 TABLE 1-6 FIG 1 AND FIG2

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2, Table 1 to 6(Length , A -IS 12817)	-	500	-
6.2, Table 1 to 6(Breadth, B-IS 12817)	-	500	-
6.2, Table 1 to 6(Breadth, B1-IS 12817)	-	500	-
6.2, Table 1 to 6(Breadth, B2-IS 12817)	-	500	-
6.2, Table 1 to 6(Thickness of flap, C-IS 12817)	-	500	-
6.2, Table 1 to 6(Dia. of Hinge pin, D-IS 12817 )	-	500	-
6.2, Table 1 to 6(Number of Knuckles- IS 12817 )	-	500	-
6.2, Table 1 to 6(Number of Screw Holes -IS 12817 )	-	500	-
6.2, Table 1 to 6(Holes for Screw Number- IS 12817 )	-	500	-
7.1(General - IS 12817 )	-	500	-
7.2(Knuckles - IS 12817 )	-	500	-
7.3(Pins- IS 12817 )	-	500	-
7.4(Screw Holes- IS 12817 )	-	500	-
7.4.2(Position of screw holes - IS 12817 )	-	500	-
7.4.2, Fig 1(The distance of the screw holes from the end of the flap - IS 12817 )	-	500	-
8.0(Finish - IS 12817 )	-	500	-
Clause 4.1.2(Silicon (Pin) )	-	200	-
Clause 4.1.2(Phosphorus (Pin) )	-	200	-
Clause 4.1.2(Sulphur (Pin) )	-	200	-
Clause 4.1.2(Manganese (Pin) )	-	200	-
Clause 4.1.2(Carbon (Pin) )	-	200	-
Clause 4.1.1(Silicon (Flap) )	-	200	-
Clause 4.1.1(Phosphorus (Flap) )	-	200	-
Clause 4.1.1(Sulphur (Flap) )	-	200	-
Clause 4.1.1(Manganese (Flap) )	-	200	-
Clause 4.1.1(Carbon (Flap) )	-	200	-
Clause 7.4.2 (Dimension - Z )	-	500	-
Clause 7.4.2 (Dimension - Y )	-	500	-
Clause 7.4.2 (Dimension - X )	-	500	-
Clause 7.4.1(Number of holes)	-	500	-
As per Cl.4(Carbon)	-	200	-
As per Cl.4(Sulphur)	-	200	-
As per Cl.4(Phosphorus)	-	200	-
As per Cl.4(Manganese)	-	200	-
As per Cl.4(Nitrogen)	-	200	-
As per Cl.4(Silicon)	-	200	-
As per Cl.4(Aluminium)	-	200	-
As per Cl.4(Chromium)	-	200	-
As per Cl.4(Vanadium)	-	200	-
As per Cl.4(Molybdenum)	-	200	-
As per Cl.4(Niobium)	-	200	-
As per Cl.4(Nickel)	-	200	-
As per Cl.4(Copper)	-	200	-
As per Cl.4(Titanium)	-	200	-
As per Cl.4(Zirconium)	-	200	-
As per Cl.4(Tungsten)	-	200	-
Cl.4(Other Elements - IS 228 and its parts or any other intrumental/chemical methods)	-	200	-
As per Cl.4(Cerium)	-	200	-

30 Mar, 2027

-
Included w.e.f 16.12.2025

IS 14587 (2025)

Prelaminated Medium Density Fibre Boards of Wood and Other Lignocellulosic Materials - Specification ( Second Revision )

HMG

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	1000	-
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	1000	-
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	1000	-
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	1000	-
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	1000	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	2000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	2000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	1000	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	1000	-
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	1000	-
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	1000	-
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	1000	-
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	1000	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	1000	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	1000	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	2000	-

30 Mar, 2027

-
Included w.e.f 08.12.2025 Exclusion: As per Clause 9.1 , Table 9 (Steady-state formaldehyde emission, Fc, mg/m3 (optional test))

IS 3087 (2025)

Medium Density Particle Boards of Wood and other Lignocellulosic Materials for General Purpose - Specification ( Third Revision )

REG(GRADE A/B)/MR/HMR FORMALDEHYDE EMISSION CLASS E1 AND E2

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	1000	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Thickness, Sanded/finished panel - IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Edge straightness, Max. -IS 2380 (Part 2))	-	1000	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	2000	-
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	1000	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	500	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	1000	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	500	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	2000	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	1	-

30 Mar, 2027

-
Included w.e.f 08.12.2025 Exclusion: As per Clause 9.1 , Table 9 (Steady-state formaldehyde emission, Fc, mg/m3 (optional test))

IS 12406 (2025)

Medium Density Fibre Boards of Wood and Other Lignocellulosic Materials for General Purpose - Specification ( Third Revision )

REG , MR AND HMR (GP/FN), FORMALDEHYDE CLASS E1 AND E2

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	1000	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Thickness - IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	1000	-
As per Clause 8, Table 2(Edge straightness, Max.)	-	1000	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	1000	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	500	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	1000	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	1000	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	2000	-
Cl-5.1(Wood and Any Other Lignocellulosic Material)	-	250	-
Cl-5.2(Adhesive)	-	250	-
Cl-5.3(Sizing Material)	-	200	-
Cl-5.4(Preservative Treatment)	-	250	-
Cl-6(MANUFACTURE)	-	250	-

30 Mar, 2027

-
Included w.e.f 08.12.2025 Exclusion: As per Clause 9.1 , Table 9 (Steady-state formaldehyde emission, Fc, mg/m3 (optional test))

IS 12823 (2025)

Prelaminated Medium Density Particle Boards from Wood and other Lignocellulosic Material Specification (Second Revision)

as per table 1 and formaldehyde class E1 and E2

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Material - IS 3087)	-	500	-
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	1000	-
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	1000	-
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	1000	-
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	1000	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	2000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	2000	-
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	1000	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	1000	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	1500	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	1000	-
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	2000	-
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	1500	-
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	1500	-
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	1000	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	1000	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	2500	-

30 Mar, 2027

-
Included w.e.f 08.12.2025 Exclusion: As per Clause 9.1 , Table 9 (Steady-state formaldehyde emission, Fc, mg/m3 (optional test))

IS 848 (2025)

Synthetic Resin Adhesives for Plywood (Phenolic, Aminoplastic and Bio-Materials Based) - Specification ( Third Revision )

BWP/BWR/MR

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 4 Table 1(TYPES)	-	500	-
As per Clause 6.6(SETTING TIMES AND CONDITIONS)	-	1000	-
As per Clause 7.3.2 Table 1(i)(Cyclic Test For BWP Type)	-	5000	-
As per Clause 7.3.2 Table 1(ii)(Cyclic Test For BWR Type)	-	5000	-
As per Clause 7.3.2 Table 1(iii)(Cyclic Test For MR Type)	-	5000	-
As per Clause 7.4(Acidity And Alkalinity (pH))	-	2000	-
As per Clause 9(Marking)	-	200	-

30 Mar, 2027

-
Included w.e.f 10.12.2025

IS 1328 (2025)

Veneered Decorative Plywood - Specification ( Fourth Revision )

MR/BWR/BWP, TYPE 1,2,3 & 4, FORMALDEHYDE CLASS E1 & E2

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Grades)	-	500	-
Cl 4.2(Type)	-	500	-
Cl 4.3(Formaldehyde Class)	-	2000	-
Cl 5.2(Adhesive)	-	1500	-
Cl 7.1(Surface Requirements- For Type 1)	-	1000	-
Cl 7.2(Surface Requirements- For Type 2)	-	1000	-
Cl 7.3(Surface Requirements- For Type 3)	-	1000	-
Cl 7.4(Surface Requirements- For Type 4)	-	1000	-
Cl 8.1(Dimensions (Length and Width))	-	2000	-
Cl 8.2(Dimensions (Thickness))	-	1000	-
Cl 8.3(Squareness and Edge Straightness as Per Annex B)	-	1500	-
Cl 8.4- Table 1(Tolerances)	-	500	-
Cl 11.3(Moisture Content)	-	2000	-
Cl 11.4.1(a)(Water Resistance Test( For MR Grade))	-	2000	-
Cl 11.4.1(b)(Water Resistance Test( For BWR Grade))	-	2000	-
Cl 11.4.1(c)(Water Resistance Test( For BWP Grade))	-	2000	-
Cl 11.5(Formaldehyde Content Test)	-	2500	-
Cl 12(Marking)	-	500	-

30 Mar, 2027

-
Included w.e.f. 04.11.2025

IS 10523 (2014)

Baby toilet soap - Specification (First Revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description)	-	1000	-
4.2(Ingredients)	-	1000	-
4.3, Table - 1, i)(Total fatty matter, percent by mass , Min)	-	3000	-
4.3, Table - 1, ii)(Moisture and valatile matter (at 105 degree Celsius ) , precent by mass , Max)	-	2000	-
4.3, Table - 1, iii)(Matter in solubale in alcohol , percent by mass , Max)	-	2500	-
4.3, Table - 1, iv)(Matter in solubale in water , percent by mass , Max)	-	2500	-
4.3, Table - 1, v)(Free caustic alkali, as sodium hydroxide (NaOH) ,percent by mass , Max)	-	2500	-
4.3, Table - 1, vi)(Chlorides, as sodium chloride ( NaCl) , percent by mass, Max)	-	2500	-
4.3, Table - 1, vii)(Free carbonated alkali ,percent by mass, Max)	-	2500	-
4.3, Table - 1, viii)(Freedom from resin)	-	2000	-
4.3, Table - 1, ix)(Freedom from grit)	-	1000	-
4.3, Table - 1, x)(Nickel content)	-	1000	-
4.3, Table - 1, xi)(Iron content as parts per million , Max)	-	3000	-
4.3, Table - 1, xii)(Copper as (Cu) contents parts per million , Max)	-	3000	-
4.4(Optional Requirements for ECO mark)	-	100	-
5.2(Marking)	-	500	-
Cl-4.3,Table 1,sl.no-i(Total Fatty matter)	-	3000	-
Cl-4.3,Table 1,sl.no-ii(Moisture and volatile Matter)	-	2000	-
Cl-4.3,Table 1,sl.no-iii(Matter insoluble in alcohol)	-	2500	-
Cl-4.3,Table 1,sl.no-iv(Matter insoluble in water)	-	2500	-
Cl-4.3,Table 1,sl.no-v(Free caustic alkali as sodium hydroxide)	-	2500	-
Cl-4.3,Table 1,sl.no-vi(Chloride)	-	2500	-
Cl-4.3,Table 1,sl.no-vii(Free Carbonated alkali)	-	2500	-
Cl-4.3,Table 1,sl.no-viii(Freedom from Rosin)	-	2000	-
Cl-4.3,Table 1,sl.no-ix(Freedom from grit)	-	1000	-
Cl-4.3,Table 1,sl.no-x(Nickel content)	-	1000	-
Cl-4.3,Table 1,sl.no-xi(Iron content)	-	3000	-
Cl-4.3,Table 1,sl.no-xii(Copper Content)	-	3000	-
5.1(Packing)	-	500	-

30 Mar, 2027

-
Included w.e.f 08.12.2025

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

TYPE AND GRADE AS PER TABLE 1, SIZE 25.4 -406.3 MM OD

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	3000	-
13(Mechanical Testing)	-	3000	-
6.0(Workmanship)	-	1000	-
4.1(Sulphur-Percentage by mass)	-	200	-
4.1(Phosphorus-Percentage by mass)	-	200	-
8.0(Straightness)	-	1000	-
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	1000	-
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	1000	-
11.1(Surface Protection)	-	2500	-
11.2(Surface Protection)	-	2500	-
13.1.3(Tensile Strength)	-	2000	-
13.1.1(Yield Stress)	-	2000	-
13.1.2(Elongation)	-	2000	-
13.2(Flattening Test)	-	200	-
13.3(Bend Test (Strip))	-	1000	-
13.5(Drift Expansion Test)	-	1000	-
13.6(Crush Test)	-	1000	-
19.1.3(Height of Internal Fin)	-	1000	-
6.0(Workmanship)	-	0	REPEAT
4.1(Sulphur-Percentage by mass)	-	0	REPEAT
4.1(Phosphorus-Percentage by mass)	-	0	REPEAT
8.0(Straightness)	-	0	REPEAT
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	0	REPEAT
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	0	REPEAT
11.1(Surface Protection)	-	0	REPEAT
11.2(Surface Protection)	-	0	REPEAT
13.1.3(Tensile Strength)	-	0	REPEAT
13.1.1(Yield Stress)	-	0	REPEAT
13.1.2(Elongation)	-	0	REPEAT
13.2(Flattening Test)	-	0	REPEAT
13.3(Bend Test (Strip))	-	0	REPEAT
13.5(Drift Expansion Test)	-	0	REPEAT
13.6(Crush Test)	-	0	REPEAT
19.1.3(Height of Internal Fin)	-	0	REPEAT
Cl. 10 Annex B Cl. 17, Cl. 19(Moment of inertia)	-	0	REPEAT
Cl. 10 Annex B Cl. 17, Cl. 19(Radius of gyration)	-	0	REPEAT
Cl. 10 Annex B Cl. 17, Cl. 19(Modulus of section)	-	0	REPEAT
Cl. 10 Annex B Cl. 17, Cl. 19(Area of cross section)	-	0	REPEAT
Cl. 19.1.3(Internal Fin Height)	-	0	REPEAT
Cl. 10 Annex B Cl. 17, Cl. 19(Mass)	-	0	REPEAT
Cl. 9(Length)	-	0	REPEAT
4.0 (a)(Carbon as C - IS:8811)	-	0	REPEAT
4.0 (b)(Manganese as Mn - IS:8811)	-	0	REPEAT
4.0 (b)(Manganese as Mn - IS:8811)	-	0	REPEAT
4.0 (c)(Micro Alloying elements (Nb+V+Ti))	-	0	REPEAT
4.0 (f)(Nitrogen content)	-	0	REPEAT
9(Length -SOP MT-23)	-	0	REPEAT
10(Outside diameter-SOP MT-23)	-	0	REPEAT
10(Thickness - SOP MT-23)	-	0	REPEAT
10(Mass of Tube-SOP MT-23)	-	0	REPEAT
10(Area of Cross Section)	-	0	REPEAT
16(Marking)	-	0	REPEAT
CL 10("1.Outer dia (04) 2.Thickness (08)")	-	0	REPEAT
CL 10(Minimum Outer dia (04))	-	0	REPEAT
CL 10(Maximum Outer dia (04))	-	0	REPEAT
Cl-10(" Minimum Thickness (08)")	-	0	REPEAT
CL 10(Maximum Thickness (08))	-	0	REPEAT
13.4(Bend Test (Whole Tube))	-	0	REPEAT

30 Mar, 2027

-
Included w.e.f. 22.09.2025 Exclusion: 13.4 (Bend Test (Whole Tube))

IS 4329 (1967)

Specification for measuring (Travelling) microscope

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No. 3(Dimension)	-	3000	-
Cl. No. 4(General requirement)	-	3000	-
Cl. No. 5(Functional requirement)	-	3000	-
Cl. No. 6.1(stage)	-	2000	-
Cl. No. 6.2(Magnification)	-	2000	-
Cl. No. 6.3(Numerical aperture)	-	2000	-
Cl. No. 6.4(Resolving Power)	-	2000	-
Cl. No. 6.5(Moment of horizontal cartillage )	-	2000	-
Cl. No. 6.6(Vertical moment)	-	2000	-
Cl. No. 6.7.1(Cross wire)	-	2000	-
Cl. No. 6.8(Fine motion )	-	2000	-
Cl. No. 7(Marking)	-	1000	-
Cl. No. 3(Dimension)	-	0	REPEAT
Cl. No. 4(General requirement)	-	0	REPEAT
Cl. No. 5(Functional requirement)	-	0	REPEAT
Cl. No. 6.1(stage)	-	0	REPEAT
Cl. No. 6.2(Magnification)	-	0	REPEAT
Cl. No. 6.3(Numerical aperture)	-	0	REPEAT
Cl. No. 6.4(Resolving Power)	-	0	REPEAT
Cl. No. 6.5(Moment of horizontal cartillage )	-	0	REPEAT
Cl. No. 6.6(Vertical moment)	-	0	REPEAT
Cl. No. 6.7.1(Cross wire)	-	0	REPEAT
Cl. No. 6.8(Fine motion )	-	0	REPEAT
Cl. No. 7(Marking)	-	0	REPEAT
Cl. No. 3(Dimension)	-	0	REPEAT
Cl. No. 4(General requirement)	-	0	REPEAT
Cl. No. 5(Functional requirement)	-	0	REPEAT
Cl. No. 6.1(stage)	-	0	REPEAT
Cl. No. 6.2(Magnification)	-	0	REPEAT
Cl. No. 6.3(Numerical aperture)	-	0	REPEAT
Cl. No. 6.4(Resolving Power)	-	0	REPEAT
Cl. No. 6.5(Moment of horizontal cartillage )	-	0	REPEAT
Cl. No. 6.6(Vertical moment)	-	0	REPEAT
Cl. No. 6.7.1(Cross wire)	-	0	REPEAT
Cl. No. 6.8(Fine motion )	-	0	REPEAT
Cl. No. 7(Marking)	-	0	REPEAT

30 Mar, 2027

-
Cl. No. 4 (General requirement) THERMAL EXPANSION COEFFICENT EQUIPMENT NOT AVAILABLE

IS 303 (2024)

Plywood for General Purposes â Specification (Fourth Revision)

MR,BWR,BWP and Emission class E1 and E2 WITH AMND No1

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Classification by appearance)	-	1000	-
Cl-5.2, Table- 1 (i)(Blister)	-	500	-
Cl-5.2, Table- 1 (ii)(Checks)	-	500	-
Cl-5.2, Table- 1 (iii)(Discolouration)	-	500	-
Cl-5.2, Table- 1 (iv)(Dote)	-	500	-
Cl-5.2, Table- 1 (v)(Insect hole)	-	500	-
Cl-5.2, Table- 1 (vi)(Joints)	-	500	-
Cl-5.2, Table- 1 (vii)(Knots (dead))	-	500	-
Cl-5.2, Table- 1 (viii)(Pin knots (dead))	-	500	-
Cl-5.2, Table- 1 (ix)(Pin knots (live))	-	500	-
Cl-5.2, Table- 1 (x)(Knots (tight))	-	500	-
Cl-5.2, Table- 1 (xi)(Patches)	-	500	-
Cl-5.2, Table- 1 (xii)(Splits)	-	500	-
Cl-5.2, Table- 1 (xiii)(Swirl)	-	500	-
Cl-5.2, Table-2(Maximum Number of Categories of Permissible Defects, per m2)	-	500	-
Cl-6.1(Timber)	-	500	-
Cl-6.2(Adhesive)	-	200	-
Cl-7.2.1(Thickness of veneers)	-	500	-
Cl-7.2.3(Grain Direction)	-	200	-
Cl-7.2.5.1(Gaps in cores and cross-bands)	-	500	-
Cl-7.2.5.2(Splits)	-	500	-
Cl-7.2.5.3(Overlap)	-	500	-
Cl-8.1(Dimensions -length)	-	1500	-
Cl-8.2(Thickness of the plywood boards)	-	1000	-
Cl-8.3(Squareness)	-	1000	-
Cl-11.3.1, 11.3.1.1(Water Resistance Test)	-	2000	-
Cl-11.3.2(Mycological Test)	-	2000	-
Cl-11.4(Moisture Content)	-	1000	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	2500	-
Cl-11.5, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	2500	-
Cl-11.6(Formaldehyde Content Test)	-	4500	-
Cl-9(WORKMANSHIP AND FINISH)	-	-	-
Cl-7.2.4(Scarf Joints)	-	-	-
Cl. 4(Grades)	-	-	-
Cl.5.1(Type based on classification by appearance)	-	-	-
Cl.5.2(Quality Requirements of Plywood for General Purposes)	-	-	-
Cl.8.1(Dimensions -width)	-	-	-
Cl.8, 8.3 & Annex C(Edge Straightness)	-	-	-
Cl.8, 8.3 & Annex C(Edge Squareness)	-	-	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	-	-
Cl-11.5, Table-4,(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	-	-
Cl-8.3(Edge Straightness)	-	-	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	-	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	-	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	-	-
Cl-11.5, Table-4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	-	-
Cl-13(Marking)	-	-	-

30 Mar, 2027

-
-

IS 6528 (2024)

Stainless steel wire - Specification ( Second Revision )

2.0-16 MM TABLE 3, 4, 5 & 6

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 6(FREEDOM FROM DEFECTS)	-	1000	-
As per clause 7(CARBON)	-	1000	-
As per clause 7(SILICON)	-	1000	-
As per clause 7(MANGANESE)	-	1000	-
As per clause 7(PHOSPHORUS)	-	1000	-
As per clause 7(SULPHUR)	-	1000	-
As per clause 7(MOLYBEDNUM)	-	1000	-
As per clause 7(NICKEL)	-	1000	-
As per clause 7(NITROGEN)	-	1000	-
As per clause 7(COPPER)	-	1000	-
As per clause 7(NIOBIUM)	-	1000	-
As per clause 7(ALUMINIUM)	-	1000	-
As per clause 8(HEAT TREATMENT)	-	200	-
As per clause 9(Dimension Tolerance)	-	2000	-
As per clause 10(TENSILE TEST)	-	2000	-
As per clause 10.2(REVERSE BEND TEST)	-	500	-
As per clause 10.3(TORSION TEST)	-	500	-
As per clause 14(FINISH)	-	500	-
As per clause 15(CORROSION RESISTANCE)	-	1500	-
As per clause 16.2(MARKING)	-	500	-
As per clause 7(TITANIUM)	-	1000	-
As per clause 7(CHROMIUM)	-	1000	-
As per Clause 6(FREEDOM FROM DEFECTS)	-	0	REPEATED
As per clause 7(CARBON)	-	0	REPEATED
As per clause 7(SILICON)	-	0	REPEATED
As per clause 7(MANGANESE)	-	0	REPEATED
As per clause 7(PHOSPHORUS)	-	0	REPEATED
As per clause 7(SULPHUR)	-	0	REPEATED
As per clause 7(MOLYBEDNUM)	-	0	REPEATED
As per clause 7(NICKEL)	-	0	REPEATED
As per clause 7(NITROGEN)	-	0	REPEATED
As per clause 7(COPPER)	-	0	REPEATED
As per clause 7(NIOBIUM)	-	0	REPEATED
As per clause 7(ALUMINIUM)	-	0	REPEATED
As per clause 8(HEAT TREATMENT)	-	0	REPEATED
As per clause 9(Dimension Tolerance)	-	0	REPEATED
As per clause 10(TENSILE TEST)	-	0	REPEATED
As per clause 10.2(REVERSE BEND TEST)	-	0	REPEATED
As per clause 10.3(TORSION TEST)	-	0	REPEATED
As per clause 14(FINISH)	-	0	REPEATED
As per clause 15(CORROSION RESISTANCE)	-	0	REPEATED
As per clause 16.2(MARKING)	-	0	REPEATED
As per clause 7(TITANIUM)	-	0	REPEATED
As per clause 7(CHROMIUM)	-	0	REPEATED
As per Clause 6(FREEDOM FROM DEFECTS)	-	0	REPEATED
As per clause 7(CARBON)	-	0	REPEATED
As per clause 7(SILICON)	-	0	REPEATED
As per clause 7(MANGANESE)	-	0	REPEATED
As per clause 7(PHOSPHORUS)	-	0	REPEATED
As per clause 7(SULPHUR)	-	0	REPEATED
As per clause 7(MOLYBEDNUM)	-	0	REPEATED
As per clause 7(NICKEL)	-	0	REPEATED
As per clause 7(NITROGEN)	-	0	REPEATED
As per clause 7(COPPER)	-	0	REPEATED
As per clause 7(NIOBIUM)	-	0	REPEATED
As per clause 7(ALUMINIUM)	-	0	REPEATED
As per clause 8(HEAT TREATMENT)	-	0	REPEATED
As per clause 9(Dimension Tolerance)	-	0	REPEATED
As per clause 10(TENSILE TEST)	-	0	REPEATED
As per clause 10.2(REVERSE BEND TEST)	-	0	REPEATED
As per clause 10.3(TORSION TEST)	-	0	REPEATED
As per clause 14(FINISH)	-	0	REPEATED
As per clause 15(CORROSION RESISTANCE)	-	0	REPEATED
As per clause 16.2(MARKING)	-	0	REPEATED
As per clause 7(TITANIUM)	-	0	REPEATED
As per clause 7(CHROMIUM)	-	0	REPEATED
As per Clause 6(FREEDOM FROM DEFECTS)	-	0	-
As per clause 7(CARBON)	-	0	-
As per clause 7(SILICON)	-	0	-
As per clause 7(MANGANESE)	-	0	-
As per clause 7(PHOSPHORUS)	-	0	-
As per clause 7(SULPHUR)	-	0	-
As per clause 7(MOLYBEDNUM)	-	0	-
As per clause 7(NICKEL)	-	0	-
As per clause 7(NITROGEN)	-	0	-
As per clause 7(COPPER)	-	0	-
As per clause 7(NIOBIUM)	-	0	-
As per clause 7(ALUMINIUM)	-	0	-
As per clause 8(HEAT TREATMENT)	-	0	-
As per clause 9(Dimension Tolerance)	-	0	-
As per clause 10(TENSILE TEST)	-	0	-
As per clause 10.2(REVERSE BEND TEST)	-	0	-
As per clause 10.3(TORSION TEST)	-	0	-
As per clause 14(FINISH)	-	0	-
As per clause 15(CORROSION RESISTANCE)	-	0	-
As per clause 16.2(MARKING)	-	0	-
As per clause 7(TITANIUM)	-	0	-
As per clause 7(CHROMIUM)	-	0	-

30 Mar, 2027

-
Included w.e.f 29.09.2025

IS 1239 : Part 1 (2004)

Steel Tubes, Tubulars and Other Wrought Steel Fittings : Part 1 Steel Tubes (BI-LINGUAL)

Light/Medium/Heavy, As per Table 3,4 & 5

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	1000	-
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	1000	-
6.2 AND AS PER IS 513(NITROGEN)	-	500	-
6.2 AND AS PER IS 513(MICRO ALLOY)	-	750	-
6.2 AND AS PER IS 513(ALUMINIUM)	-	500	-
6.2 AND AS PER IS 513(SILICON)	-	500	-
6.2 AND AS PER IS 513(MANGANESE)	-	500	-
6.2 AND AS PER IS 513(PHOSPHORUS)	-	500	-
6.2 AND AS PER IS 513(SULPHUR)	-	500	-
6.2 AND AS PER IS 513(CARBON)	-	500	-
6.2 AND AS PER IS 10748(COPPER)	-	500	-
6.2 AND AS PER IS 10748(NITROGEN)	-	500	-
6.2 AND AS PER IS 10748(MICRO ALLOY)	-	750	-
6.2 AND AS PER IS 10748(ALUMINIUM)	-	500	-
6.2 AND AS PER IS 10748(SILICON)	-	500	-
6.2 AND AS PER IS 10748(CARBON EQUIVALENT)	-	500	-
6.2 AND AS PER IS 10748(MANGANESE)	-	500	-
6.2 AND AS PER IS 10748(PHOSPHORUS)	-	500	-
6.2 AND AS PER IS 10748(SULPHUR)	-	500	-
6.2 AND AS PER IS 10748(CARBON)	-	500	-
Clause - 6.1.1, Table-1( ALUMINIUM)	-	500	-
Clause - 6.1.1, Table-1(SILICON)	-	500	-
Clause - 6.1.1, Table-1(NITROGEN)	-	500	-
Clause - 6.1.1, Table-1(MANGANESE)	-	500	-
Clause - 6.1.1, Table-1(PHOSPHURS)	-	500	-
Clause - 6.1.1, Table-1(SULPHUR)	-	500	-
Clause - 6.1.1, Table-1( CARBON)	-	500	-
12 AND AS PER IS 4736(UNIFORMITY OF ZINC COATING)	-	500	-
12 AND AS PER IS 4736(MASS OF ZINC COATING)	-	500	-
6.2 AND AS PER IS 513(NITROGEN)	-	500	-
6.2 AND AS PER IS 513(MICRO ALLOY)	-	500	-
6.2 AND AS PER IS 513(ALUMINIUM)	-	500	-
6.2 AND AS PER IS 513(SILICON)	-	500	-
6.2 AND AS PER IS 513(MANGANESE)	-	500	-
6.2 AND AS PER IS 513(PHOSPHORUS)	-	500	-
6.2 AND AS PER IS 513(SULPHUR)	-	500	-
6.2 AND AS PER IS 513(SULPHUR)	-	500	-
6.2 AND AS PER IS 513(CARBON)	-	500	-
6.2 AND AS PER IS 513(CARBON)	-	500	-
6.2 AND AS PER IS 10748(COPPER)	-	500	-
6.2 AND AS PER IS 10748(COPPER)	-	500	-
6.2 AND AS PER IS 10748(NITROGEN)	-	500	-
6.2 AND AS PER IS 10748(NITROGEN)	-	500	-
6.2 AND AS PER IS 10748(MICRO ALLOY)	-	500	-
6.2 AND AS PER IS 10748(MICRO ALLOY)	-	500	-
6.2 AND AS PER IS 10748(ALUMINIUM)	-	500	-
6.2 AND AS PER IS 10748(ALUMINIUM)	-	500	-
6.2 AND AS PER IS 10748(SILICON)	-	500	-
6.2 AND AS PER IS 10748(SILICON)	-	500	-
6.2 AND AS PER IS 10748(CARBON EQUIVALENT)	-	500	-
6.2 AND AS PER IS 10748(CARBON EQUIVALENT)	-	500	-
6.2 AND AS PER IS 10748(MANGANESE)	-	500	-
6.2 AND AS PER IS 10748(MANGANESE)	-	500	-
6.2 AND AS PER IS 10748(PHOSPHORUS)	-	500	-
6.2 AND AS PER IS 10748(PHOSPHORUS)	-	500	-
6.2 AND AS PER IS 10748(SULPHUR)	-	500	-
6.2 AND AS PER IS 10748(SULPHUR)	-	500	-
6.2 AND AS PER IS 10748(CARBON)	-	499.87	-
6.2 AND AS PER IS 10748(CARBON)	-	499.87	-
6.1.1(MANGANESE)	-	500	-
6.1.1(MANGANESE)	-	500	-
6.1.1(PHOSPHORUS)	-	500	-
6.1.1(PHOSPHORUS)	-	500	-
6.1.1(SULPHUR)	-	500	-
6.1.1(SULPHUR)	-	500	-
6.1.1(CARBON)	-	500	-
6.1.1(CARBON)	-	500	-
Cl. 6.1.1, table1 of IS 1239(Part1)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1.1, table1 of IS 1239(Part1)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1.1, table1 of IS 1239(Part1)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1.1, table1 of IS 1239(Part1)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1.1, table1 of IS 1239(Part1)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 6.1.1, table1 of IS 1239(Part1)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 15(Workmanship)	-	500	-
Cl. 15(Workmanship)	-	500	-
Cl. 14.3(Flattening test (Over 50 mm NB))	-	1000	-
Cl. 14.3(Flattening test (Over 50 mm NB))	-	1000	-
Cl. 14.1.1(Elongation)	-	2000	-
Cl. 14.1.1(Elongation)	-	2000	-
Cl. 14.1(Tensile Strength)	-	2000	-
Cl. 3.3, 10.2(Plain End)	-	1000	-
Cl. 3.3, 10.2(Plain End)	-	1000	-
Cl. 11(Length)	-	500	-
Cl. 8, 9 Table 3,4 & 5(Mass of Tube)	-	1000	-
Cl. 8, 9 Table 3,4 & 5(Mass of Tube)	-	1000	-
Cl. 6.5(Height of Internal Fin)	-	500	-
Cl. 6.5(Height of Internal Fin)	-	500	-
Cl. 8, 9 Table 3,4 & 5(Thickness)	-	500	-
Cl. 8 Table 3,4 & 5(Outside Diameter)	-	500	-
Cl. 8 Table 3,4 & 5(Outside Diameter)	-	500	-
Clause 14.1.1(Elongation Percent)	-	2000	-
Clause 11.3(Approximate Length)	-	500	-
Clause 11.3(Approximate Length)	-	500	-
Clause 11.2(Exact Length)	-	500	-
Clause 11.2(Exact Length)	-	500	-
Clause 11.1(Random Length)	-	500	-
Clause 11.1(Random Length)	-	500	-
Clause 8.1 (Table3,4,5)(Nominal Bore )	-	500	-
Clause 8.1 (Table3,4,5)(Nominal Bore )	-	500	-
Cl 15(Workmanship)	-	500	-
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	3000	-
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	3000	-
Cl 12(Workmanship)	-	500	-
Cl 12(Workmanship)	-	500	-
Cl 10.1.1(Manufacturing )	-	500	-
Cl 10.1.1(Manufacturing )	-	500	-
Cl 10.1(Manufacturing )	-	500	-
Cl 10.1(Manufacturing )	-	500	-
Cl 8(Outer Diameter, Thickness & Mass)	-	2000	-
Cl 8(Outer Diameter, Thickness & Mass)	-	2000	-
17(Marking)	-	500	-
cl.17(MARKING)	-	500	-
cl.17(MARKING)	-	500	-
6.2(Carbon Equivalent as CE- IS:8811-98(RA12))	-	1500	-
6.2(Carbon Equivalent as CE- IS:8811-98(RA12))	-	1500	-
Cl. 14.2(Bend Test (uto and including 50 mm NB))	-	1000	BEND TEST SETUP INSTALLED
Cl. 14.2(Bend Test (uto and including 50 mm NB))	-	1000	BEND TEST SETUP INSTALLED

30 Mar, 2027

-
-

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

TABLE 1 DIM AS PER TABLE 5 TO12

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1, 8.1.1 & 10.1 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
6(Freedom From Defects)	-	500	-
9.3(Tensile Test-1608:Part 1)	-	2000	-
9.3, Table 3 (Yield Strength, Mpa)	-	2000	-
9.3, Table 3 (Tensile Strength, Mpa)	-	1500	-
9.3, Table 3 (Elongation, %)	-	1000	-
9.4(Erichsen Cupping Test,(Average depth of cupping) mm)	-	2000	-
11(Surface finish)	-	1000	-
12(Dimensions)	-	2500	-
14.1(Thickness,mm)	-	1000	-
14.2( Width, mm)	-	1000	-
14.3(Length, mm)	-	500	-
14.4(Flatness, mm)	-	1000	-
14.5(Camber, mm)	-	1000	-
Clause 9.1, 9.2 & Table 3(IS 1608 Part 1)	-	0	REPEATED CLAUSE
17(Marking)	-	500	-
Clause 9.1, 9.2 & Table 3(0.2 Percent Yield Strength)	-	0	REPEATED CLAUSE
4.1(General requirements)	-	0	REPEATED CLAUSE
6(Freedom from defects)	-	0	REPEATED CLAUSE
7(Heat treatment)	-	100	-
8.1, table 1(C Si Mn Ni Cr S P Cu Ni)	-	0	REPEATED CLAUSE
9.1(Sample plan)	-	0	REPEATED CLAUSE
9.2(Tensile test)	-	0	REPEATED CLAUSE
9.3(Mechanical properties)	-	0	REPEATED CLAUSE
9.4(Erichsen cupping test)	-	0	REPEATED CLAUSE
10(Retests)	-	0	REPEATED CLAUSE
11(Surface finish)	-	0	REPEATED CLAUSE
12(Dimensions)	-	0	REPEATED CLAUSE
13(Edge condition)	-	500	-
14.1(Thickness)	-	0	REPEATED CLAUSE
14.2.1(Mill Edge)	-	500	-
14.2.2(Trimmed Edge)	-	500	-
8.1.1, table 2(Carbon Silicon Manganese Nickel Chromium Sulphur Phosphorus Copper Nitrogen)	-	0	REPEATED CLAUSE
14.3(Length)	-	0	REPEATED CLAUSE
14.4(Flatness)	-	0	REPEATED CLAUSE
14.5(Camber)	-	0	REPEATED CLAUSE
15(Inspection)	-	0	REPEATED CLAUSE
17(Marking)	-	0	REPEATED CLAUSE

30 Mar, 2027

-
Included w.e.f 30.05.2025

IS 18219 (2023)

Borosilicate glass 3.3 - Properties

table 1,2 and 3

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	1000	-
5.2(Hydrolytic resistance)	-	6000	-
6.1 & 6.2, Table-1(Outer tube diameter-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Outer tube diameter-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Light wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Light wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Medium wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Medium wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Heavy wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Heavy wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Outer tube diameter-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Outer tube diameter-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Light wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Light wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Medium wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Medium wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Heavy wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Heavy wall thickness-Tolerance)	-	1000	-
6.3(Length)	-	1000	-
6.4(Straightness)	-	1000	-
6.5(Ovality)	-	1000	-

30 Mar, 2027

-
Included w.e.f.28.07.2025 exclusion Cl 5.3 (Thermal coefficient of expansion)

IS 18236 (2023)

LABORATORY GLASSWARE - BOROSILICATE GLASS TUBING (First Revision)

TABLE 1,2 AND 3

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	1000	-
5.2(Hydrolytic resistance)	-	4000	-
6.1 & 6.2, Table-1(Outer tube diameter-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Outer tube diameter-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Light wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Light wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Medium wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Medium wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Heavy wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Heavy wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Outer tube diameter-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Outer tube diameter-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Light wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Light wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Medium wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Medium wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Heavy wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Heavy wall thickness-Tolerance)	-	1000	-
6.3(Length)	-	1000	-
6.4(Straightness)	-	1000	-
6.5(Ovality)	-	1000	-
5.1(General)	-	1000	-
5.2(Hydrolytic resistance)	-	4000	-
6.1 & 6.2, Table-1(Outer tube diameter-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Outer tube diameter-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Light wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Light wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Light wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Medium wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Medium wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-1(Heavy wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-1(Heavy wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Outer tube diameter-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Outer tube diameter-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Light wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Light wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Medium wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Medium wall thickness-Tolerance)	-	1000	-
6.1 & 6.2, Table-2(Heavy wall thickness-Nominal value)	-	1000	-
6.1 & 6.2, Table-2(Heavy wall thickness-Tolerance)	-	1000	-
6.4(Straightness)	-	1000	-
6.5(Ovality)	-	1000	-
6.3(Length)	-	1000	-
6.5(Ovality)	-	1000	-
5.1(General)	-	0	repeated
5.2(Hydrolytic resistance)	-	0	repeated
6.1 & 6.2, Table-1(Outer tube diameter-Nominal value)	-	0	repeated
6.1 & 6.2, Table-1(Outer tube diameter-Tolerance)	-	0	repeated
6.1 & 6.2, Table-1(Light wall thickness-Nominal value)	-	0	repeated
6.1 & 6.2, Table-1(Light wall thickness-Nominal value)	-	0	repeated
6.1 & 6.2, Table-1(Light wall thickness-Tolerance)	-	0	repeated
6.1 & 6.2, Table-1(Medium wall thickness-Nominal value)	-	0	repeated
6.1 & 6.2, Table-1(Medium wall thickness-Tolerance)	-	0	repeated
6.1 & 6.2, Table-1(Heavy wall thickness-Nominal value)	-	0	repeated
6.1 & 6.2, Table-1(Heavy wall thickness-Tolerance)	-	0	repeated
6.1 & 6.2, Table-2(Outer tube diameter-Nominal value)	-	0	repeated
6.1 & 6.2, Table-2(Outer tube diameter-Tolerance)	-	0	repeated
6.1 & 6.2, Table-2(Light wall thickness-Nominal value)	-	0	repeated
6.1 & 6.2, Table-2(Light wall thickness-Tolerance)	-	0	repeated
6.1 & 6.2, Table-2(Medium wall thickness-Nominal value)	-	0	repeated
6.1 & 6.2, Table-2(Medium wall thickness-Tolerance)	-	0	repeated
6.1 & 6.2, Table-2(Heavy wall thickness-Nominal value)	-	0	repeated
6.1 & 6.2, Table-2(Heavy wall thickness-Tolerance)	-	0	repeated
6.4(Straightness)	-	0	repeated
6.5(Ovality)	-	0	repeated
6.3(Length)	-	0	repeated
6.5(Ovality)	-	0	repeated

30 Mar, 2027

-
Included w.e.f.28.07.2025 exclusion Cl 5.3 (Thermal coefficient of expansion)

IS 208 (1996)

Door Handles - Specification ( Sixth Revision )

type 1, type 2,type 3, Type 4 Dim. Table 2A, 2B, 2C

4750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017)(Chemical composition - Carbon - IS 228)	-	4750	-
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017)(Chemical composition - Manganese - IS 228)	-	4750	-
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017)(Chemical composition - Phosphorus - IS 228)	-	4750	-
4.2 -Table 1- i (Ref. Cl 7.1 -Table 3 Grade 0 of IS 1079 : 2017)(Chemical composition - Sulphur - IS 228)	-	4750	-
4.2 -Table 1- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	4750	-
4.2 -Table 1- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	4750	-
4.2 -Table 1- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	4750	-
4.2 -Table 1- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	4750	-
4.2 -Table 1- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	4750	-
4.2 -Table 1- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Copper - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Silicom - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Magnesium - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Iron - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Manganese - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Nickel - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Zinc - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Lead - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Tin - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Titanium - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- iv (Ref. Cl 5.1, Table 1 Grade 5230 or 4600 of IS 617 : 1994)(Chemical composition - Aluminium - IS 504:1963, IS 7658:1975, IS 11035:1984)	-	4750	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008)(Chemical composition - Aluminium - IS 504:1963)	-	4750	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008)(Chemical composition - Copper - IS 504:1963)	-	4750	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008)(Chemical composition - Magnesium - IS 504:1963)	-	4750	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008)(Chemical composition - Silicon - IS 504:1963)	-	4750	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008)(Chemical composition - Iron - IS 504:1963)	-	4750	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008)(Chemical composition - Manganese - IS 504:1963)	-	4750	-
4.2 -Table 1- v (Ref. Cl 6, Table 1 Grade 19000 of IS 737 : 2008)(Chemical composition - Zinc - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and/or other grain refining elements - IS 504:1963)	-	4750	-
4.2 -Table 1- vi (Ref. Cl 5.1, Table 1 Grade 63400 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504:1963)	-	4750	-
4.2 -Table 1- vii (Ref. Cl 6.1 of IS 210 : 2009)(Chemical composition - Sulphur and/or Phosphorous)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Aluminium- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Copper- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Magnesium- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Copper- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Iron- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Lead- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964)	-	4750	-
4.2 -Table 1- viii (Ref. Cl 4.1, Table 1 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964)	-	4750	-
3(TYPES-Doors handle shall be of the following types according to the materials used:)	-	4750	-
5.1(MANUFACTURE- General)	-	4750	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size (A,B,C,D,E,F,G,H,I))	-	4750	-
6.1 Table2A & 2B and Fig 1,2,3,4(DIMENSIONS - Size 1. No. in each Lug 2. No. in a plate when a continious plate is used 3. Size Designation of Counter-sunk Head Wood Screws (as per IS 6760: 1972))	-	4750	-
6.2(Tolerance)	-	4750	-
9(MARKING)	-	4750	-
9.1(BIS Certification Marking)	-	4750	-
10(PACKING)	-	4750	-

30 Mar, 2027

-
Included w.e.f.28.07.2025 Exclusion Cl 4.2 -Table 1- vii (Ref. Cl 9.1 of IS 210 : 2009) Cl 4.2 -Table 1- vii (Ref. Cl 9..11 of IS 210 : 2009

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

TABLE 1 AND TABLE

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	10000	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	10000	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	10000	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	10000	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	10000	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	10000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	10000	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	10000	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	10000	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	10000	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	10000	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	10000	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	10000	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	10000	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	10000	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	10000	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	10000	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	10000	-
Cl. 15, 16(Off Centre of Web)	-	10000	-
Cl. 15, 16(Flange out of square (I beam))	-	10000	-
Cl. 15, 16(Width of flange (I Beam))	-	10000	-
Cl. 15, 16(Depth (I Beam))	-	10000	-
Cl. 15, 16(Mass (Plate))	-	10000	-
Cl. 15, 16(Flange Slope)	-	10000	-
Cl. 15, 16(Web Thickness)	-	10000	-
Cl. 15, 16(Flange Thickness)	-	10000	-
Cl. 15, 16(Out of Square (Flat))	-	10000	-
Cl. 15, 16(Width )	-	10000	-
Cl. 15, 16(Thickness )	-	10000	-
Cl. 15, 16(Sectional Area )	-	10000	-
Cl. 15, 16(Camber (Angle))	-	10000	-
Cl. 15, 16(Out of Square (Angle))	-	10000	-
Cl. 15, 16(Weight)	-	10000	-
Cl. 15, 16(Leg Length Difference (Angle))	-	10000	-
Cl. 15, 16(Leg Length B (Angle))	-	10000	-
Cl. 15, 16(Leg Length A (Angle))	-	10000	-
Cl. 15, 16(Toe Radius R2)	-	10000	-
Cl. 15, 16(Root Radius R1)	-	10000	-
Cl 18(Weight)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 7(Workmanship)	-	10000	-
Cl 10.3(UTM)	-	10000	-
Cl 11.3(Press)	-	10000	-
Cl 12(Sudden Load Applied)	-	10000	-
Cl 15(Length, Width & Thickness)	-	10000	-
Cl 18(Weight)	-	10000	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 5(By Calculation)	-	10000	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	10000	-
Clause 8, Table 1, Note 6(By Calculation)	-	10000	-
Clause 7(IS 2062)	-	10000	-
Clause 11.3(IS 1599)	-	10000	-
Clause 12(IS 1757)	-	10000	-
Clause 15, Table 4(IS 2062)	-	10000	-
16(Tolerance)	-	10000	-
20(Marking)	-	10000	-
20(MARKING)	-	10000	-
8(Micro Alloying elements)	-	10000	-
8(Niobium as Nb)	-	10000	-
8(Vanadium as V)	-	10000	-
8(Titanium as Ti)	-	10000	-
10(Tensile Strength-IS:1608(P1)-22)	-	10000	-
10(Yield Stress-IS:1608(P1)-22)	-	10000	-
10(Elongation on SoA 5.65mm GL)	-	10000	-
15(Sectional Area)	-	10000	-
15(Dimension -D)	-	10000	-
15(Dimension -B)	-	10000	-
15(Thickness - t)	-	10000	-
15(Thickness - T)	-	10000	-
15(Flange Slope)	-	10000	-
15(Radius R1)	-	10000	-
15(Radius R2)	-	10000	-
15(Mass -SOP MT-23)	-	10000	-
15(Sectional Area)	-	10000	-
15(Dimension -D)	-	10000	-
15(Dimension -B)	-	10000	-
15(Thickness - t)	-	10000	-
15(Thickness - T)	-	10000	-
15(Radius R1)	-	10000	-
15(Radius R2)	-	10000	-
15(Mass -SOP MT-23)	-	10000	-
15(Sectional Area)	-	10000	-
15(Dimensions AxB)	-	10000	-
15(Thickness - t)	-	10000	-
15(Radius -R1)	-	10000	-
15(Radius -R2)	-	10000	-
15(Diameter)	-	10000	-
15(Sectional Area)	-	10000	-
15(Mass per metre)	-	10000	-
15(Mass per metre)	-	10000	-
15(Ovality)	-	10000	-
15(Side Width)	-	10000	-
15(Sectional Area)	-	10000	-
15(Mass per metre)	-	10000	-
15(Out of Square)	-	10000	-
9(Preparation of test sample)	-	10000	-
Clause 8, Table 1, Note 2(Aluminium)	-	10000	-
Clause 8, Table 1, Note 5(Niobium)	-	10000	-
Clause 8, Table 1, Note 5(Titanium)	-	10000	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	10000	-
Clause 8, Table 1, Note 6(Boron)	-	10000	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	10000	-
Clause 7(Freedom from Defect)	-	10000	-
Clause 11.3(Bend Test)	-	10000	-
Clause 12(Impact Test)	-	10000	-
Clause 15, Table 4(Dimension)	-	10000	-
5(General Requirements)	-	10000	-
4(MARKING)	-	10000	-
15(Mass -SOP MT-23)	-	10000	-

30 Mar, 2027

-
Included w.e.f.28.07.2025 Exclusion Cl 13 (Y Groove Cracking Test) Cl 14.1 (Soundness test) Cl 14.2 (Grain Size) Cl 14.2 (Inclusion)

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

WELL TECH TEST AND RESEARCH CENTER, DERABASSI

INDUSTRIAL BLOCK -B , VILLAGE SAIDPURA, DERABASSI, MOHALI, S.A.S Nagar, Punjab, 140507

7973565868 wtechresearch@gmail.com

Scope List