BIS - LIMS (Laboratory Information Management System)

RTRC LIMITED, GURUGRAM

Plot No. 296, Sector-7, Phase-II,Industrial Estate,IMT Manesar, Gurugram, Gurugram, Gurugram, Haryana, 122050

8826495200 qa@rtrc.in

Scope List

Reset

48 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 9968 : Part 1 (1988)

Specification for elastomer insulatedcables: Part 1 for working voltages up to and including 1100 volts (First Revision)

56500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1( Copper Cooduetor)	-	0	-
3.2(Aluminium conductor)	-	0	-
4.1(INSULATION : lnsulation for General Service)	-	0	-
4.2(INSULATION : Heat Resisting insulation)	-	0	-
4.3(INSULATION : Silicone Rubber Insulation)	-	0	-
5.1(TAPE : Proofed Tape)	-	0	-
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	0	-
5.3(TAPE : Giass Tape)	-	0	-
6.1(FILLERS : )	-	0	-
7.1(BRAID : Textile Braid)	-	0	-
7.2(BRAID : Glass Braid )	-	0	-
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	0	-
8.2(SHEATH :Heat Resisting Insulated Cables)	-	0	-
9.1(PresenRtive Compound)	-	0	-
9.2(Varnish)	-	0	-
10( Conductor )	-	0	-
11(Separator tape)	-	0	-
12.2(Insulation : Thickness of Insufatien)	-	1000	-
12.4(Insulation : Allplication of Insulation)	-	0	-
13(CORE IDENTiFICATlON)	-	0	Additional charge, Rs. 1500 /- For each additional core
14(Tape)	-	0	-
15(BRAIDING)	-	0	-
16(COMPOUNDING AND VARNISHING)	-	0	-
17(LAYING UP OF CORES)	-	0	-
18( Binder tape)	-	0	-
19.2(Sheath : Thickness of Sheath)	-	1000	-
19.4( Sheath :Colour)	-	0	-
20( Overall diameter)	-	1000	-
21. (a)(Persulphate tests (for copper))	-	1000	-
21. (b)(Annealing Test (for coper))	-	1000	-
21. (c)( Tensile Test (for aluminium))	-	1000	-
21. (d)( Wrapping Test (for aluminium))	-	1000	-
21. (e)(Conductor Resistance )	-	1000	-
21.1( Tensile strength )	-	1000	-
22.1( Elongation)	-	1000	-
21.1(type test : Ageing In air oven)	-	5000	-
21.1(type test : Ageing in air bomb)	-	5000	-
21.1(type test : Ageing In oxygen bomb)	-	6500	-
21.1(type test : Hot set elongation)	-	1500	-
21.1(type test : Tear resistance )	-	3500	-
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	5000	-
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	3000	-
21(Water absorption test)	-	8500	-
23(identification)	-	0	-
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	0	-
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	0	-
Cl No. 4.1(Ageing in air bomb - Elongation)	-	0	-
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	0	-
Cl No. 4.1(Ageing in air oven - Elongation)	-	0	-
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	0	-
Cl No. 22.2(High Voltage Test (Water Immersion))	-	0	-
Cl No. 4.1(Insulation resistance)	-	2000	-
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	0	-
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	2500	-
Cl No. 23.1, 23.2(Identification)	-	0	-
21.1((f) Oil resistance)	-	4500	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 1554 : Part 2 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 2 for working voltages from 3.3 kV up to and including 11 kV (Second Revision)

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CONDUCTOR)	-	0	Additional Charges, Rs 1500/- for each additional core. Additional Charges for FR-LSH/FR test as applicable
3.1.1(CONDUCTOR)	-	0	-
4.1(INSULATION)	-	0	-
5.1(SCREENING)	-	0	-
5.1.1(Non-magnetic Metallic Tape for SingleCore Unscreened and Unarmoured Cables)	-	0	-
6.1(FILLERS AND INNER SHEATH)	-	0	-
6.2(FILLERS AND INNER SHEATH)	-	0	-
7.1(ARMOURING)	-	0	-
7.2(ARMOURING)	-	0	-
8.1(OUTER SHEATH)	-	0	-
9.1(CONDUCTOR)	-	0	-
9.2(CONDUCTOR)	-	0	-
10.1(CONDUCTOR SCREENING)	-	0	-
11.1(INSULATION)	-	0	Additional Charge, Rs 25000/- for each additional Core
11.2(INSULATION : Thickness of Insulation)	-	1500	-
11.3(INSULATION : Tolerance on Thickness of Insulation)	-	0	-
11.4(INSULATION : Application of Insulation)	-	0	-
12.1(INSULATION SCREENING)	-	0	-
12.2(INSULATION SCREENING)	-	0	-
12.3(INSULATION SCREENING)	-	0	-
12.4(INSULATION SCREENING)	-	0	-
13.1(CORE IDENTIFICATION)	-	0	-
13.1.1(CORE IDENTIFICATION)	-	0	-
14.1(LAYING UP OF CORES)	-	0	-
15.1(INNER SHEATH (COMMON COVERING))	-	500	-
15.2(INNER SHEATH (COMMON COVERING))	-	0	-
15.3(INNER SHEATH (COMMON COVERING))	-	0	-
15.4(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	500	-
15.4.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	0	-
16.1.1(ARMOURING : Application)	-	0	-
16.1.2(ARMOURING : Application)	-	0	-
16.1.3(ARMOURING : Direction of lay )	-	0	-
16.1.4(ARMOURING : Application)	-	1500	-
16.2.1(ARMOURING : Type of Armour)	-	0	-
16.2.2(ARMOURING : Type of Armour)	-	0	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
17.1(OUTER SHEATH)	-	0	-
17.2(OUTER SHEATH : colour )	-	500	-
17.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	1500	-
17.3.2(Thickness of Outer Sheath : Armoured Cables)	-	1500	-
18.1 a) 1)(Tests on Conductor : Annealing test (for copper))	-	1000	AS APPLICABLE
18.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	0	AS APPLICABLE
18.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	0	AS APPLICABLE
18.1 a) 3)(Tests on Conductor : Wrapping test ( for aluminium))	-	0	-
18.1 a)4)(Tests on conductor : Conductor resistance test - Main conductor )	-	3500	-
18.1 a)4)(Resistance test - Neutral conductor )	-	0	-
18.1 d) 1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
18.1 d) 1)(Phyaical tests for insulation : Elongation )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Tensile stregth )	-	1000	-
18.1 d) 1)(Physical tests for sheath : Elongation )	-	1000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	2500	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	2500	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2500	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2500	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	0	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2500	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage )	-	2500	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
18.1 d) 5)( Loss of mass in air oven- sheath )	-	5000	-
18.1 d) 6)(Heat shock test- Insulation )	-	2000	-
18.1 d) 6)(Heat shock test- sheath )	-	2000	-
18.1 d) 7)(Thermal stability- insulation )	-	1000	-
18.1 d) 7)(Thermal stability- Sheath )	-	1000	-
18.1 d) 8)(Water absorption (gravimetric)(for insulation, where applicable))	-	5500	-
18.1 e)(Insulation resistance test : Volume Resistivity )	-	0	-
18.1 e)(Insulation resistance test : IR Constant )	-	2500	-
19.2(Partial discharge test)	-	22000	-
19.3(Bending test)	-	5000	-
19.4(Dielectric power factor test)	-	0	-
19.4(Dielectric power factor test)	-	15000	-
19.5(Heating cycle test)	-	35000	-
19.6(Impulse withstand test)	-	18000	-
19.7(High voltage test)	-	9000	-
19.8(Flammability test)	-	3500	-
19.9(Oxygen Index Test)	-	2500	-
19.10(Flame Retardance Test on Single Cables)	-	3000	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage )	-	2500	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	2500	-
18.1 d) 4)(Hot deformation : Insulation )	-	2500	-
18.1 d) 4)(Hot deformation : Sheath )	-	2500	-
18.1 d) 5)( Loss of mass in air oven- Insulation )	-	5000	-
19.11(Flame Retardance Test on Bunched Cables)	-	0	Additional Charge, if applicable
19.13(Test for Halogen Acid Gas Evolution)	-	0	Additional Charge, if applicable
19.14(Temperature Index)	-	0	Additional Charge, if applicable
18.4(Optional Test : Cold Impact )	-	1500	-
20.1(IDENTIFICATION : Manufacturer's Identification)	-	0	-
20.2(IDENTIFICATION : Cable Identification)	-	0	-
20.3(IDENTIFICATION : Cable Code)	-	0	-
16.3(Armouring : Dimensions -Wire Diameter)	-	1500	-
16.3(Armouring : Dimensions -Formed wire )	-	1500	-
16.4(ARMOURING : Joints)	-	0	-
16.5(ARMOURING : Resistance)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	0	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	2500	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 16246 (2015)

Elastomer insulated cables with limited circuit integrity when affected by fire - Specification

101500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 19.4( Cable Code)	-	0	Additional Charges, Rs 1500/- for each additional core.
Cl 19.3( Cable Identification)	-	0	-
Cl 19.2( Voltage Identification)	-	0	-
Cl.4.1( Cables for Fixed Installation)	-	0	-
Cl.5( INSULATION)	-	0	-
Cl. 6.1( Glass Tape)	-	0	-
Cl 6.2( Polyethylene Teraphthalate (PETP) or Polypropylene base Tape)	-	0	-
Cl 6.4( Fire Barrier Tape)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 8( ARMOUR)	-	0	-
Cl 9.1( Inner Sheath)	-	0	-
Cl 9.2( Outer Sheath)	-	0	-
Cl 10.1( CONDUCTORS)	-	1000	-
Cl 10.2( CONDUCTORS)	-	0	-
Cl 11.1( INSULATION)	-	0	-
Cl 19.1( Manufacturer’s Identification)	-	0	-
Cl 18.4.2(Flame Retardence Test on Bunched Cables IS 10810 : Part 63)	-	14500	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	0	-
Cl 18.4.1( Flame Retardence Test on Single Cable IS 10810 : Part 61)	-	3000	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 16.2( OUTER SHEATH)	-	0	-
Cl 16.3( Thickness of Outer Sheath - Avg IS 10810 : Part 6)	-	500	-
Cl 16.3( Thickness of Outer Sheath - Minimum IS 10810 : Part 6)	-	500	-
Cl 11.2(Thickness of Insulation IS 10810 : Part 6)	-	500	-
Cl 12( CORE IDENTIFICATION)	-	0	-
Cl 13( LAYING UP OF CORES)	-	0	-
Cl 14.2( Thickness of Inner Sheath IS 10810 : Part 6)	-	500	-
Cl 15.1( ARMOURING)	-	0	-
Cl 15.3.1( Type of Armour)	-	0	-
Cl 15.3.2( Type of Armour)	-	0	-
Cl 15.3.3( ARMOURING)	-	0	-
Cl 15.3.3( ARMOURING)	-	0	-
Cl 15.4.1( ARMOURING)	-	0	-
Cl 17.2(Annealing test (for copper) IS 10810 : Part 1)	-	1000	-
Cl 17.2(Conductor resistance test IS 10810 : Part 5)	-	1000	-
Cl 17.1(Persulphate test (tinned copper conductor) IS 10810 : Part 4)	-	1000	-
Cl 17.2(Tensile strength before ageing on insulation IS 10810 : Part 7)	-	2000	as applicable
Cl 17.2(elongation at break before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(Tensile strength after Ageing in air bomb IS 10810 : Part 56)	-	2000	-
Cl 17.2(Elongation after Ageing in air bomb IS 10810 : Part 56)	-	2000	-
Cl 17.2(Tensile strength variation)	-	0	-
Cl 17.2(Elongation Variation)	-	0	-
Cl 17.2(Hot set elongation on insulation IS 10810 : Part 30)	-	1500	-
Cl 17.2(Permanent elongation (set) on insulation IS 10810 : Part 30)	-	0	-
Cl 17.1(Tensile strength before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(elongation at break before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(Hot set elongation test on sheath IS 10810 : Part 30)	-	1500	-
Cl 17.1(Permanent elongation (set) test on sheath IS 10810 : Part 30)	-	0	-
Cl 17.1(Oxygen index test on sheath IS 10810 : Part 58)	-	2500	-
Cl 17.1(Temperature index test on sheath IS 10810 : Part 64)	-	2500	-
Cl 17.1(Acid gas generation on sheath IS 10810 : Part 39)	-	5000	-
Cl 17.2(Insulation resistance test IS 10810 : Part 43)	-	2500	-
Cl 17.1(Water absorption test (for insulation) IS 10810 : Part 28)	-	14500	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2500	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2500	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	35000	as applicable

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	0	Additional charge, Rs. 1000 /- For each additional core, Additional Charges for FR-LSH/FR test as applicable
11.2(Legibility)	-	250	-
11.1(Durability)	-	250	-
11(Identification)	-	1000	Additional charge, Rs. 1000 /- For each additional core
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	5000	Additional charge, If applicable
10.4(Flammability test- Unaffected portion)	-	0	-
10.4(Flammability test-Burning after flame removal)	-	500	-
table 1 e) 3) (IR constant- max. Temp)	-	250	-
table 1 e) 3) (IR constant- Room temp )	-	250	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	250	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	250	-
10.2(HV (room temperature))	-	1000	-
10.1(HV (water immersion))	-	1000	-
10.1(HV (water immersion))	-	5500	(d.c. high voltage test)
10.8(Smoke density rating)	-	3500	Additional charge, If applicable
10.6(Halogen evolution)	-	3500	Additional charge, If applicable
10.7(Temperature index)	-	2500	Additional charge, If applicable
10.5(Oxygen index)	-	2500	Additional charge, If applicable
Table 1 iii) d) 9)(Cold impact for sheath)	-	1250	Additional charge, If applicable
Table 1 iii) d) 8)(Cold bend for sheath)	-	1250	Additional charge, If applicable
Table 1 iii) c) 9)(Cold impact for insulation)	-	1250	Additional charge, If applicable
Table 1 iii) c) 8)(Cold bend for insulation)	-	1250	Additional charge, If applicable
Table 1(Category Code)	-	0	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1000	Additional charge, If applicable
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	1000	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	1000	Additional charge, If applicable
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1000	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	750	Additional charge, If applicable
Table 1 iii) c) 5)(Heat shock-Insulation )	-	750	-
Table 1 iii) d) 4)(Cracks Observed)	-	0	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	1000	Additional charge, If applicable
Table 1 iii) c) 4)(Cracks Observed)	-	0	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	1000	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	4500	Additional charge, If applicable
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	4500	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	0	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	500	Additional charge, If applicable
Table 1 iii) d) 3)(Sheath- TS variation)	-	500	Additional charge, If applicable
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	500	Additional charge, If applicable
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	500	Additional charge, If applicable
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	500	Additional charge, If applicable
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	500	Additional charge, If applicable
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	500	Additional charge, If applicable
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
16.2(Tests)	-	0	-
16.1(Construction)	-	0	-
15(PACKING AND MARKING)	-	0	-
13(CABLE CODE)	-	0	-
12(CORE IDENTIFICATION)	-	0	-
11(IDENTIFICATION)	-	1000	Additional charge, Rs. 1000 /- For each additional core
10.11(Persulphate Test)	-	1000	Additional charge, Rs. 1000 /- For each additional core
10.1(Flex Test)	-	0	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	0	-
10.8(Smoke Density Rating)	-	3500	Additional charge, Rs. 1000 /- For each additional core
Table 1 iii) c) 3)(Elongation variation)	-	500	-
Table 1 iii) c) 3)(TS variation)	-	500	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	500	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	500	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	500	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	500	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	0	-
8.3(Thickness of Sheath)	-	500	Table 1 iii) c) 3) (TS variation)
5.2(Application )	-	0	-
10.7(Test for Temperature Index)	-	0	-
10.6(Test for Halogen Acid Gas Evolution)	-	0	-
10.5(Oxygen Index Test)	-	0	-
10.4(Flammability Test)	-	0	-
10.3(Spark Test)	-	2500	Additional charge, If applicable
10.2(High Voltage Test (at Room Temperature))	-	0	-
10.1(High Voltage Test (Water Immersion Test))	-	0	-
9(OVERALL DIMENSIONS)	-	500	-
8(SHEATH)	-	0	-
7(BINDER TAPE)	-	0	-
6(FILLER)	-	0	-
5(INSULATION)	-	0	-
4.2(Electrical Resistance)	-	0	-
4.1(Material)	-	0	-
10.3(Spark Test)	-	2500	Additional charge, If applicable
5.4(Mechanical properties before and after ageing)	-	0	-
table 1, 4.2(insulation resistance test)	-	0	-
10.3(Spark test)	-	2500	Additional charge, If applicable
Table 4(Copper purity test)	-	9000	Additional charge, If applicable
5.3(Avarage thickness of insulation)	-	0	-
5.3(Thickness of Insulation)	-	500	-
9.1(Ovality)	-	0	-
9(Overall dimensions)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	1000	Additional charge, If applicable
4.2(Conductor resistance test)	-	1000	-
4.1(Wrapping test (for Al))	-	500	-
4.1(Tensile test (for Al)- After Stranding)	-	500	-
4.1(Tensile test (for Al)-Before Stranding)	-	500	-
4.1(Annealing test (for copper))	-	750	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	0	-
5.3(Minimum thickness of insulation)	-	500	-
8.3(Avarage thickness of Sheath)	-	0	-
8.3(Minimum thickness of Sheath)	-	500	Additional charge, If applicable
Table 2, IS 8130(No fo wire in a conductor)	-	0	-
4, IS 8130(Construction of conductor)	-	0	-
12.0(Core identification)	-	0	-
10.11(Persulphate Test )	-	1000	-
4.1(Conductor - Material)	-	0	-
4.1(Conductor - Material)	-	0	-
4.4(Joints in Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0	-
5.1(Insulation)	-	0	-
6.1(Filler)	-	0	-
6.2(Filler)	-	0	-
7(Binder Tape)	-	0	-
8.1(Sheath Material )	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-
12(CONSTRUCTION Core Identification)	-	0	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 8130 (2013)

Conductors for insulated electric cables and flexible cords - Specification (Second Revision)

cable

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Aluminium)	-	0	-
4.1(Aluminium)	-	0	-
4.2(Copper)	-	0	-
4.3(Form of Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
5(Classification)	-	0	-
6(Construction)	-	0	-
7.1(Tests for Copper Conductors)	-	3500	(Diameter of wire, Annealing test, Flexibility class) - As applicable
7.2(Tests for Aluminium Conductors)	-	4500	(Diameter of wire, Tensile test, Wrapping test, Flexibility class) - As applicable
7.3(Resistance Test)	-	1500	-
8(Packing and Marking)	-	0	-
4.1(Aluminium)	-	0	-
4.1(Aluminium)	-	0	-
4.2(Copper)	-	0	-
4.3(Form of Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
5(Classification)	-	0	-
6(Construction)	-	0	-
7.1(Tests for Copper Conductors)	-	3500	(Diameter of wire, Annealing test, Flexibility class) - As applicable
7.2(Tests for Aluminium Conductors)	-	4500	(Diameter of wire, Tensile test, Wrapping test, Flexibility class) - As applicable
7.3(Resistance Test)	-	1500	-
8(Packing and Marking)	-	0	-
4.1(Aluminium)	-	0	-
4.1(Aluminium)	-	0	-
4.2(Copper)	-	0	-
4.3(Form of Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
5(Classification)	-	0	-
6(Construction)	-	0	-
7.1(Tests for Copper Conductors)	-	3500	(Diameter of wire, Annealing test, Flexibility class) - As applicable
7.2(Tests for Aluminium Conductors)	-	4500	(Diameter of wire, Tensile test, Wrapping test, Flexibility class) - As applicable
7.3(Resistance Test)	-	1500	-
8(Packing and Marking)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

CABLE

18500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	0	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	0	-
5.1(Insulation)	-	0	-
6.1(Flexibility class)	-	0	-
6.2(Compactness)	-	0	-
6.2(No of strands)	-	0	-
6.2(Surface)	-	0	-
6.3(Protective barrier)	-	0	-
6.4(size of street lighting conductor)	-	0	-
6.5(Size of messenger conductor )	-	0	-
6.6(Joints in messenger conductor )	-	0	-
6.6(Direction of outer layer)	-	0	-
7.1(Insulation)	-	0	-
7.2( Thickness of insulation)	-	500	-
7.3(Tolerance on thickness of insulation )	-	0	-
7.4(Aplication of the insulation )	-	0	-
7.5(Colour of the insulation )	-	0	-
8.1(Core identification)	-	0	-
8.2(Core identification)	-	0	-
8.3(Identification by other means)	-	0	-
9.1(Assembly (Laying up))	-	0	-
9.2(Assembly (Laying up))	-	0	-
9.3(Direction of lay)	-	0	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	500	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	500	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	500	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	500	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	3000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	500	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	500	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	500	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	500	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	3000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	500	Additional, If applicable
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	500	Additional, If applicable
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1500	Additional charge, If applicable
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	2500	Additional charge, If applicable
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	4500	Additional charge, If applicable
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1000	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	1000	-
10.1 g)(High voltage test - IS10810:Part 45)	-	1500	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	1000	Additional charge, If applicable
11.4(Bending Test on the Completed Cable ( Optional))	-	1000	Additional charge, If applicable
10.1 d) iii)(Carbon Black Content)	-	3500	Additional charge, If applicable

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	0	Additional Charges, Rs 1500/- for each additional core. Additional Charges for FR-LSH/FR test as applicable
4.1.1(INSULATION : General Purjose Insulaiion)	-	0	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	0	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
6.1(MATERIALS : ARMGURING)	-	0	-
6.2(MATERIALS : ARMGURING)	-	0	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	0	-
8.2(CONSTRUCTION : CONDUCTOR)	-	0	-
9.1(INSULATION )	-	0	-
9.2(INSULATION : Thickness of Insulation)	-	500	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	0	-
9.4(INSULATION : Application of Insulation)	-	0	-
10.1(CORE IDENTIFICATION)	-	0	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	0	-
11.1(LAYING UP OF CORES)	-	0	-
11.2(LAYING UP OF CORES)	-	0	-
12.1(INNER SHEATH)	-	0	-
12.2(INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	0	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	0	-
13.1.1(ARMOURING : Application)	-	0	-
13.1.2(Armouring: Coverage )	-	0	-
13.1.3(ARMOURING : Direction of lay )	-	0	-
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	0	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	0	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(ARMOURING : Joints)	-	0	-
13.5.1(ARMOURING : Resistance)	-	500	-
13.5.2(ARMOURING : Resistance)	-	0	-
13.6 a)(ARMOURING: Tensile Strength)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	0	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	0	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	500	-
13.6 g)(ARMOURING: Resistivity)	-	500	-
14.1(OUTER SHEATH)	-	0	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	0	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	0	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	500	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	0	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	0	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	0	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	0	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	500	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	0	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	500	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	0	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	500	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	0	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	500	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	0	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	500	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	0	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 d)4)(Hot deformation : Insulation )	-	500	-
15.1 d)4)(Hot deformation : Sheath )	-	0	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	500	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	0	-
15.1 d)6)(Heat shock test- Insulation )	-	500	-
15.1 d)6)(Heat shock test- sheath )	-	0	-
15.1 d)7)(Thermal stability- insulation )	-	500	-
15.1 d)7)(Thermal stability- Sheath )	-	0	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	500	-
15.1 e)(Insulation resistance test : IR Constant )	-	0	-
15.1 f)(High voltage test ( water immersion test ))	-	1500	-
15.1 g)(High voltage test at room temperature)	-	500	-
15.1 g)(High voltage test at room temperature)	-	0	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	500	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	500	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	0	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	0	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	500	-
16.1(DETAILS OF TESTS : General)	-	0	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	0	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	500	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	500	-
16.4(Flammability Test)	-	0	-
16.5(Oxygen Index Test)	-	2500	additional charge, if applicable
16.6(Flame Retardance Test on Single Cables)	-	0	-
16.7(Flame Retardance Test on Bunched Cables)	-	5500	additional charge, if applicable
16.9(Test for Halogen Acid Gas Evolution)	-	3500	additional charge, if applicable
16.1(Temperature Index)	-	0	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	0	-
17.2(IDENTIFICATION : Cable Identification)	-	0	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	0	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	0	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	500	-
16.4(Flammability Test- Un affected portion)	-	0	-
16.4(Flammability Test- Period of Burning)	-	0	-
9.3(Minimum Thickness of Reduce core insulation)	-	0	-
9.2(Thickness of Reduce core insulation)	-	0	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	0	-
Cl No. 16.10(Smoke density test)	-	3500	additional charge, if applicable
Cl No. 16.8(Test for specific optical density of smoke)	-	0	-
Table 4(Copper purity test)	-	0	-

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	0	Additional charges, Rs 1500/- for each additional core. FR-LSH/FR testing charge as applicable.
4(INSULATION : MATERIALS)	-	0	-
5.1(FILLER AND INNER SHEATH)	-	0	-
5.2(FILLER AND INNER SHEATH)	-	0	-
6(ARMOURING)	-	0	-
7(OUTER SHEATH)	-	0	-
8.1(CONDUCTOR: CONSTRUCTION)	-	0	-
8.2(PROTECTIVE BARRIER)	-	0	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	0	-
9.1(Insulation Applied by extrusicn)	-	0	-
9.2(Thickness of Insulation - Average)	-	500	-
9.3(Thickness of Insulation - Minimum)	-	0	-
9.4(Application of Insulation)	-	0	-
10.1(Core Identification)	-	0	-
10.2(Core Identification- Neutral)	-	0	-
10.3(Core Identification by number )	-	0	-
10.4(Core Identification by number - Neutral )	-	0	-
11(LAVING UP OF CORES)	-	0	-
12.1 & 12.2(Inner sheath : Application)	-	0	-
12.3(Thickness of Inner Sheath)	-	0	-
13.1(Armouring: Application)	-	0	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(Armouring: Direction of Lay )	-	0	-
13.2(Type of armour )	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	0	-
13.4(Armour: Joint)	-	0	-
13.5(Armouring : Resistance Test)	-	500	-
13.6 a)(ARMOURING: Tensile Strength)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	500	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	500	-
13.6 g)(ARMOURING: Resistivity)	-	500	-
14.1(Outer Sheath : Application)	-	0	-
14.2(Colour of outer sheath)	-	0	-
14.3(Thickness of outer sheath - AVERAGE)	-	500	-
14.3(Thickness of outer sheath - minimum)	-	0	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	500	as applicable
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	0	as applicable
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	0	as applicable
15.1 a) iii)(Wrapping test (for aluminium))	-	0	-
15.1 a) iv)(Resistance test - Main conductor)	-	500	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	0	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	0	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	500	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	500	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	500	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	0	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	500	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	500	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	500	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	500	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	500	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	500	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
15.1 e) v) (Sheath : Hot deformation)	-	500	-
Cl 16(Halogen Acid Gas Test)	-	0	-
Cl 16(Halogen Acid Gas Test)	-	0	-
Cl 16(Halogen Acid Gas Test)	-	0	-
15.1 e) vi) (Sheath : Heat shock test)	-	500	-
15.1 e) vii) (Sheath : Thermalstability)	-	500	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	500	-
16.2(HIGH VOLTAGE TEST )	-	500	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	500	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	0	-
16.9(Oxygen Index Test)	-	2500	additional charge, if applicable
16.1(Flame Retardance Test on Single Cables)	-	0	additional charge, if applicable
16.11(Flame Retardance Test on Bunched Cables)	-	5500	additional charge, if applicable
16.13(Test for Halogen Acid Gas Evolution)	-	3500	additional charge, if applicable
16.14(Temperature Index)	-	0	additional charge, if applicable
17.1(Manufacturer'. identification)	-	0	-
17.2(cable Indentification )	-	0	-
17.3(cable Code )	-	0	-
15.4 (a)(Cold bend)	-	1000	as applicable
15.4 (b)(Cold impact)	-	1000	as applicable
Table 1(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 4(Copper purity test)	-	0	-
Cl No. 16.15(Smoke density test)	-	3500	additional charge, if applicable
Table 2(Cold Impact test for Outer sheath)	-	0	additional charge, if applicable
Table 2(Cold bend test for Outer sheath)	-	0	additional charge, if applicable

03 Apr, 2027

-
Included w.e.f. 24.04.2024

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

89000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	0	Complete Testing Charges : Rs. 89000/- For Single core unsheathed cable Rs. 172500/- for Single core sheathed cable. Additional charge, Rs. 2000 /- For each additional core
4.1.1 b) (Material : Seperator tape )	-	0	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	0	-
4.1.1 e) (Shape of conductor )	-	0	-
4.1.1 f) (Nominal size of conductor )	-	0	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	0	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	0	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	1000	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	0	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	0	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	1500	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	1500	-
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	0	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	1500	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.3(Fillers)	-	0	-
4.4(Binder Tape)	-	0	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	0	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	0	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	0	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	0	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	1500	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	1500	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	1500	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	5000	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	1500	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	1000	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	0	-
4.5.6, 13.4(Colour of Sheath)	-	0	-
5.1(High Voltage Test (at Room Temperature))	-	2500	-
5.2(Spark Test (Routine Test))	-	0	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	2500	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	2500	As applicable
5.5(Temperature Index-IS 10810 (Part 64).)	-	2500	As applicable
5.6(Smoke Density-IS 10810 (Part 63).)	-	10000	Smoke density test (3-meter cube)
5.7(Assessment of Halogen- Table 1 of Annex D)	-	35000	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	1000	As applicable
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	2500	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	1500	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	0	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	4500	As applicable
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	0	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	12500	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	1500	As applicable
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	1500	As applicable
6.1, Table 1(CORE IDENTIFICATION)	-	0	-
6.2(Core Identification by Numbers)	-	0	-
6.2.1(Preferred Arrangement of Marking)	-	0	-
6.2.2(Durability)	-	0	-
7.0(CABLE CODE)	-	0	-
9.0( IDENTIFICATION)	-	0	-
10.1(Packing )	-	0	-
10.2(marking)	-	0	-
10.2.1(Standards marking)	-	0	-
13.3, 14.3(assembly of cores )	-	0	-
6.1(General Requirements)	-	0	-
6.1.1(Colour Combination Green Yellow)	-	0	-
12.1(Conductor)	-	0	-
12.2, Table 4(insulation)	-	0	-
Table 4(Copper Purity test)	-	9000	As applicable
4.3.1 (e)(Fluorine content test (Fillers))	-	15000	As applicable
4.3.1 (d)(Presence of fluorine test (Fillers))	-	6000	As applicable
4.3.1 (c)(Conductivity test (Fillers))	-	4000	As applicable
4.3.1 (b)(pH test (Fillers))	-	4000	As applicable
4.3.1 (a)(HCl test (Fillers))	-	6000	As applicable
5.7 (a)(HCl test (Assessment of halogen test))	-	0	As applicable
5.7 (b)(pH test (Assessment of halogen test))	-	4000	As applicable
5.7 (c)(Conductivity test (Assessment of halogen test))	-	4000	As applicable
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	6000	As applicable
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	15000	As applicable
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	2000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	1000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	4500	As applicable
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	0	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	1500	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	1000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	0	-

03 Apr, 2027

-
-

IS 17293 (2020)

Electric Cables for Photovoltaic Systems for Rated Voltage 1 500 V d.c.

1213700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	750	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	750	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1000	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	14500	-
IS 191 : 2007, IS 440(Copper purity test)	-	1200	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	11000	Smoke density test (3-meter cube)
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	500	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	7500	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	140000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1500	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	1000	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	1500	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	4000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	4000	For Conductivity Test
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	6000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	21000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	1500	For Hot Set Test
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	385000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	5000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	16000	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	1500	-
Annex - B of IS 17293:2020(Compatibility test)	-	5500	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	1500	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1000	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	3000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	1000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	4000	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	2500	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	21000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	4000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	6000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	1500	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	385000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	0	-
Annex - B of IS 17293:2020(Compatibility test)	-	0	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	1000	-
Annex - E of IS 17293 : 2020(UV resistance)	-	108000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	0	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	0	-
11.2.2(Spark Test)	-	4500	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	8500	-
11.2.5(Surface Resistance of Sheath)	-	4000	-
11.3.1(Sheath Colour)	-	0	-
11.3.2(Sheath Marking)	-	0	-
11.3.3(Overall Diameters and Ovality)	-	1000	-
Annex J(Assessment of Halogens)	-	0	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	0	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	0	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	0	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	0	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	5500	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	7500	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	0	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	0	-
5.2(Application to the Conductor)	-	0	-
5.3(Thickness)	-	0	-
6.2(Sheath application)	-	0	-
6.3(Sheath Thickness)	-	0	-
6.4(Sheath Colour)	-	0	-
7(Overall Dimension)	-	0	-
8.1(Continuity of Marking)	-	500	-
8.2(Durability)	-	1000	-
8.3(Legibility)	-	1000	-
9(Core Identification)	-	0	-
12(Packing and Marking)	-	0	-
4.1(Resistance)	-	0	-
7.1.2.1, 7.2.3(Annealing)	-	0	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	0	-

03 Apr, 2027

-
-

IS 9968 : Part 2 (2002)

Specification for elastomer - Insulated cables: Part 2 for working voltages from 3.3 kV up to and including 33 kV (First Revision)

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTORS: Cables for Fixed Installation)	-	0	-
4.2(CONDUCTORS:Flexible Cables)	-	0	-
5(INSULATION)	-	0	-
6(SEMICONDUCTING COMPOUND)	-	0	-
7.1(Proofed Tape)	-	0	-
7.1(Proofed Tape: Thickness)	-	1000	-
7.2(Polyethylene Terephthalate ( P E T P ) or Polypropylene Base Tape : Thickness)	-	1000	-
7.3(Tape )	-	0	-
8(SCREENING)	-	0	-
9(CENTRE AND FILLERS)	-	0	-
10(ARMOUR)	-	0	-
11.1(Inner Sheath)	-	0	-
11.2(Outer Sheath)	-	0	-
12.1(Tapes)	-	0	-
12.2(Cords and Yarns)	-	0	-
13.1 & 13.2(CONSTRUCTION:CONDUCTORS-Cables for Fixed Installations/Flexible Cables)	-	0	-
13.3(Earthing Conductor)	-	0	-
13.3.1(Earthing Conductor)	-	0	-
13.4(Separator Tape)	-	0	-
14(CONDUCTOR SCREENING)	-	0	-
15.1(INSULATION : Application)	-	30000	Additional Charge, Rs 30,000/- for each additional core.
15.2(Thickness of Insulation)	-	1000	-
15.3(Tolerance on Thickness of Insulation)	-	0	-
16.1(INSULATION SCREENING : Application)	-	0	-
16.2(INSULATION SCREENING : Parts )	-	0	-
16.3(INSULATION SCREENING : Non Metallic Parts )	-	0	-
16.4(INSULATION SCREENING : Metallic Parts )	-	0	-
17(CORE IDENTIFICATION)	-	0	-
17(CORE IDENTIFICATION: Unscreed cable )	-	0	-
18.1(LAYING UP OF CORES)	-	0	-
18.2(LAYING UP OF CORES : Flexible cable)	-	0	-
18.3(LAYING UP OF CORES : Binder Tape)	-	0	-
19.1(Inner Sheath : Application)	-	0	-
19.2(Thickness of Inner Sheath)	-	1000	-
19.3(Inner Sheath : proofed tape)	-	0	-
20.1(ARMOURING: Application)	-	0	-
20.2(Type of Armour)	-	0	-
20.2 1.2(Direction of lay of armour)	-	0	-
20.2 1.3(Joint in armour)	-	0	-
20.2.2(Filling Factot )	-	0	-
20.2.2(Diameter of braiding)	-	1000	-
20.2.2.1(Braiding material)	-	0	-
20.3(Substitution of the galvanized steel wires/formed)	-	0	-
21.1(OUTER SHEATH)	-	0	-
21.2(Coulor of Outer sheath)	-	0	-
21.3(Thickness of Outer Sheat: Average)	-	1000	-
21.3(Thickness of Outer Sheat: Minimum)	-	0	-
22.1 a)1)(Annealing test (for copper) - IS 10810: Part 1)	-	1500	as applicable
22.1 a)2)(Tensile test (for aluminium) -IS 10810: Part 2)	-	1500	as applicable
22.1 a)3)(Wrapping Test (for aluminium) - IS 10810: Part 3)	-	1000	-
22.1 a)4)(Conductor resistance test)	-	2500	-
22.1 a)5)(Persulphate test (tinned copper conductor)- IS 10810: Part 4)	-	1500	as applicable
22.1 b)1)(Test for Galvanized Steel Wires/Formed Wires 1) Dimensions -IS 10810: Part 36)	-	1000	-
22.1 b)2)i)(Test for Galvanized Steel Wires/Formed Wires 2) Tensile Strentgh -IS 10810: Part 37)	-	1000	-
22.1 b)2)ii)(Test for Galvanized Steel Wires/Formed Wires 2) Elongation at break -IS 10810: Part 37)	-	1000	-
22.1 b)2)iii)(Test for Galvanized Steel Wires/Formed Wires 3) Torsion (for round wires only) -IS 10810: Part 38)	-	1000	-
22.1 b)2)iv)(Test for Galvanized Steel Wires/Formed Wires 4) Winding (for strips only) -IS 10810: Part 39)	-	1000	-
22.1 b)2)v)(Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Uniformity-IS 10810: Part 40)	-	2500	-
22.1 b)2)vi)(Test for Galvanized Steel Wires/Formed Wires 5) Zinc coating : Mass -IS 10810: Part 41)	-	2500	-
22.1 b)2) vii) (Resistivity - IS 10810: Part 42)	-	1500	-
22.1 c)2)(Physical Tests for Insulation : Tensile Strenth - IS 10810: Part 7)	-	1500	-
22.1 c)2)(Physical Tests for Insulation : Elongation - IS 10810: Part 7)	-	1500	-
22.1 c)2)(Physical Tests for Sheath : Tensile Strenth - IS 10810: Part 7)	-	1500	-
22.1 c)2)(Physical Tests for Sheath : Elongation - IS 10810: Part 7)	-	1500	-
22.1 c)3)(Physical Tests for Insulation ( Ageing in air oven): Tensile Strenth - IS 10810: Part 11)	-	2500	-
22.1 c)3)(Physical Tests for Insulation ( Ageing in air oven): Tensile Strenth Variation - IS 10810: Part 12)	-	0	-
22.1 c)3)(Physical Tests for Insulation( Ageing in air oven) : Elongation - IS 10810: Part 11)	-	2500	-
22.1 c)3)(Physical Tests for Insulation( Ageing in air oven) : Elongation variation - IS 10810: Part 12)	-	0	-
22.1 c)3)(Physical Tests for Sheath( Ageing in air oven) : Tensile Strenth - IS 10810: Part 11)	-	2500	-
22.1 c)3)(Physical Tests for Sheath( Ageing in air oven) : Tensile Strenth variation - IS 10810: Part 12)	-	0	-
22.1 c)3)(Physical Tests for Sheath ( Ageing in air oven): Elongation - IS 10810: Part 11)	-	2500	-
22.1 c)3)(Physical Tests for Sheath ( Ageing in air oven): Elongation variation - IS 10810: Part 12)	-	0	-
22.1 c)4)(Physical Tests for Insulation ( Ageing in air bomb): Tensile Strenth variation - IS 10810: Part 56)	-	2500	-
22.1 c)4)(Physical Tests for Insulation( Ageing in air bomb) : Elongation variation - IS 10810: Part 56)	-	2500	-
22.1 c)4)(Physical Tests for Sheath(Ageing in air bomb) : Tensile Strenth variation - IS 10810: Part 56)	-	2500	-
22.1 c)4)(Physical Tests for Sheath ( Ageing in air bomb): Elongation variation - IS 10810: Part 56)	-	2500	-
22.1 c)5)(Physical Tests for Insulation :Hot set Elongation - IS 10810: Part 30)	-	4000	-
22.1 c)5)(Physical Tests for Insulation :Permanent set - IS 10810: Part 30)	-	0	-
22.1 c)5)(Physical Tests for Sheath :Hot set Elongation - IS 10810: Part 30)	-	5000	-
22.1 c)5)(Physical Tests for Sheath :Permanent set - IS 10810: Part 30)	-	0	-
22.1 c)6)(Physical Tests for Sheath(Oil resistance test) : Tensile Strenth Variation - IS 10810: Part 31)	-	3000	-
22.1 c)6)(Physical Tests for Sheath ( Oil resistance test): Elongation Variation - IS 10810: Part 31)	-	3000	-
22.1 c)7)(Tear Resistance test - IS 10810: Part 17)	-	5500	-
22.1 c)8)(Shrinkage : Insulation - IS 10810: Part 12)	-	3500	-
22.1 c)8)(Shrinkage test- Crack observed : Insulation - IS 10810: Part 13)	-	0	-
22.1 c)8)(Shrinkage test : Sheath - IS 10810: Part 12)	-	3000	-
22.1 c)8)(Shrinkage test - Crack oberved : Sheath - IS 10810: Part 13)	-	0	-
22.1 c)9)(Hot deformation test : Insulation - IS 10810: Part 15)	-	2500	-
22.1 c)9)(Hot deformation test : Sheath - IS 10810: Part 15)	-	2500	-
22.1 c)10)(Loss of mass in air oven : Insulation - IS 10810: Part 10)	-	3000	-
22.1 c)10)(Loss of mass in air oven : Sheath - IS 10810: Part 10)	-	3500	-
22.1 c)11)(Heat shock : Insulation - IS 10810: Part 14)	-	2500	-
22.1 c)11)(Heat shock : Sheath - IS 10810: Part 14)	-	2500	-
22.1 c)12)(Thermal stability : Insulation - IS 10810: Part 60)	-	1000	-
22.1 c)12)(Thermal stability : Sheath - IS 10810: Part 60)	-	1000	-
22.1 d)(Insulation Resistance Test: Volume resistivity )	-	3500	-
22.1 d)(Insulation Resistance Test: Insulation resistance constant )	-	0	-
22.1 e)(Partial Discharge Test)	-	18000	-
22.1 f)(Bending Test Followed by Partial Discharge Test)	-	0	-
22.1 g)(Dielectric Power Factor Test 1) As a function of Voltage)	-	8000	-
22.1 g)(Dielectric Power Factor Test 1) As a function of temperature)	-	7000	-
22.1 h)(Heating Cycle Test)	-	18000	-
22.1 j)(Impulse Withstand Test)	-	15000	-
22.1 m)(Water Absorption Test - IS 10810: Part 28)	-	5500	-
22.1 n)(Flammability)	-	3000	-
24.1(Manufacturer's Identification)	-	0	-
24.2(Voltage Identification)	-	0	-
24.3(Cable Code)	-	0	-
25.2.1(Marking on drum )	-	0	-
25.2.2(BIS Certification Marking)	-	0	-
22.1 k)(High Voltage Test for Four Hours)	-	5000	-

03 Apr, 2027

-
-

IS 7098 : Part 3 (1993)

Cross - Linked polyethylene insulated thermoplastic sheathed cables - Specification: Part 3 for working voltages from 66 kV up to and including 220 kV

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
6(SCREENING)	-	0	-
7.1(MOISTURE BARRIER : Laminated Tape)	-	0	-
7.2(MOISTURE BARRIER : Lead Alloy Sheath)	-	0	-
7.3(MOISTURE BARRIER : Water Blocking Tape/Powder)	-	0	-
8.1(INNER SHEATH)	-	0	-
8.2(INNER SHEATH)	-	0	-
8.3(INNER SHEATH)	-	0	-
9.1(ARMOUR)	-	0	-
9.2(ARMOUR)	-	0	-
10.1(OUTER SHEATH)	-	0	-
10.2(OUTER SHEATH)	-	0	-
11.1(CONDUCTOR)	-	0	-
11.2(CONDUCTOR)	-	0	-
12.1(CONDUCTOR SCREENING )	-	0	-
12.2(CONDUCTOR SCREENING )	-	0	-
13.1(INSULATION)	-	0	-
13.2(INSULATION)	-	0	-
14.1(INSULATION SCREENING)	-	0	-
14.2.1(INSULATION SCREENING : Non-metallic Part)	-	0	-
14.2.2(INSULATION SCREENING : Non-metallic Part)	-	0	-
14.2.3(INSULATION SCREENING : Non-metallic Part)	-	0	-
14.3.1(INSULATION SCREENING : Metallic Part)	-	0	-
14.3.2(INSULATION SCREENING : Metallic Part)	-	0	-
14.3.3(INSULATION SCREENING : Metallic Part)	-	0	-
15.1(MOISTURE BARRIER)	-	0	-
15.2.1(Metallic Sheath)	-	0	-
15.2.2(Metallic Sheath)	-	0	-
16.1(INNER SHEATH)	-	0	-
16.2(INNER SHEATH)	-	0	-
17.1(ARMOUR)	-	0	-
17.2(ARMOUR)	-	0	-
17.3(ARMOUR)	-	0	-
17.4(ARMOUR)	-	0	-
17.5(ARMOUR)	-	0	-
18.1(OUTER SHEATH)	-	0	-
18.2(outer sheath colour)	-	0	-
18.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	2500	-
18.3.1(Thickness of Outer Sheath : armoured Cables)	-	2500	-
19.1 A) I)(Tests on conductor : Annealing test ( for copper ))	-	2500	-
19.1 A) II)(Tests on conductor : Resistance test)	-	12500	-
19.1 b) I)(Test for thickness and dimensions of insulation)	-	5000	-
19.1 b) II)(Tensile strength and elongation at break)	-	5000	-
19.1 b) III)(Thermal ageing in air oven)	-	10000	-
19.1 b) IV)(Hot set test)	-	6500	-
19.1 b) V)(Shrinkage test)	-	3500	-
20.3(Test for concentric metallic screen : Test for concentric copper wire)	-	5000	-
20.4(Test for concentric copper tape)	-	5000	-
20.5(Thickness of metallic sheath)	-	3500	-
20.6(Tests for armouring material : Dimensions)	-	3500	-
19.1 f) II)(Tests for armouring material : Tensile strength and elongation at break)	-	2000	-
Table 9, (Measurement of thickness)	-	1000	-
19.1 g)2) i)(PVC sheath : Tensile strength and elongation at break)	-	2000	-
19.1 g)2) iii)(PVC sheath : Loss of mass)	-	5500	-
19.1 g)2) v)(PVC sheath : Hot deformation test)	-	2500	-
19.1 g)2) vi)(PVC sheath : Shrinkage test)	-	3500	-
19.1 g)2) vii)(PVC sheath : Thermal stability)	-	1500	-
19.1 g)3) ii)(PE sheath : Tensile strength and elongation at break before and after ageing)	-	2000	If Applicable
19.1 g)3) iii)(PE sheath : Hot-detormation)	-	2500	Additional Charge, If Applicable
20.7(Flammabihty test ( for PVC outer sheathed cables only ))	-	3000	-
20.8.3(Water tightness test)	-	35000	-
20.9.1(Thermal ageing on complete cable sample)	-	12500	-
19.1 k) ii)(Tensile strength and elongation at breakfor insulation and outer sheath)	-	0	-
20.2(Resistivity test for semi-conducting layer)	-	7500	-
20.11.1(Bending test followed by P D test)	-	65000	-
20.12, 20.18(Dielectric power factor and capacitance measurement at ambient temperature)	-	18500	-
20.13(Dielectric power factor measurement at elevated temperature)	-	18500	-
20.14.1(Load cycle test followed by P.D measurement)	-	75000	-
20.15(Impulse Voltage Test Followed by High Voltage Test)	-	65000	-
19.5(Check on Insulation Thickness Before the Electrical Type Tests)	-	4000	-
20.16.1(Test for Dimensions of Insulation : Insulation Thickness)	-	4000	-
20.16.2(Test for Dimensions of Insulation : Test for Eccentricity)	-	4000	-
20.16.3(Test for Dimensions of Insulation : Test for Ovality)	-	3000	-
20.17(High Voltage Test ( as Routine and Acceptance Tests ) )	-	25000	-
20.18(Measurement of Capacitance)	-	25000	-

03 Apr, 2027

-
Exclusion: Above 66 kv for the following clauses, Testing Facility for Cl.20.17 (High Voltage Test ( as Routine and Acceptance Tests ) ), Cl. 20.18 (Measurement of Capacitance), Cl. 20.15 (Impulse Voltage Test Followed by High Voltage Test), Cl. 20.14.1 (Load cycle test followed by P.D measurement), Cl. 20.13 (Dielectric power factor measurement at elevated temperature), Cl. 20.12, 20.18 (Dielectric power factor and capacitance measurement at ambient temperature), Cl. 20.11.1 (Bending test followed by P D test)

IS 14494 (2019)

Elastomer insulated flexible cables for use in mines - Specification (First Revision)

240000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(CONDUCTOR)	-	0	Complete Testing Charges : Rs 55000/- Three Core Cable upto 1.1 KV Cable. Rs 73000/- Three Core Cable for 1.9/3.3 KV Cable. Rs 80000/- Three Core Cable for 3.8/6.6 KV Cable. Rs 250000/- Four Core Cable for 6.35/11 KV Cable.
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.1(FILLERS)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	500	-
11.2 b)(ARMOURING: Elongation )	-	500	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	500	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	500	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	1000	Additional charge, Rs 1000/- for each additional core above three core cable up to 1.9/3.3 kV. Rs 5000/- for each additional core above three core cable above 1.9/3.3 kV
16.2(INSULATION : Thickness of Insulation)	-	1000	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	0	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
17.4(INSULATION SCREEN)	-	0	-
18(PROTECTIVE SCREEN)	-	0	-
19(CONDUCTANCE OF SCREEN)	-	0	-
19.1(Individual Core Screen)	-	0	-
19.2(Collective Screen)	-	0	-
20.1(CORE IDENTIFICATION)	-	0	-
20.2(Colour Scheme for Identification)	-	0	-
20.3(Scheme for Identification by Numbering)	-	0	-
21.1(LAYING UP OF CORES)	-	0	-
21.2(LAYING UP OF CORES)	-	0	-
21.3(LAYING UP OF CORES)	-	0	-
21.4(LAYING UP OF CORES)	-	0	-
22.1(INNER SHEATH)	-	0	-
22.2(Thickness of Inner Sheath)	-	500	-
22.3(INNER SHEATH)	-	0	-
23.1(ARMOURING)	-	0	-
23.2(ARMOURING)	-	0	-
23.3(ARMOURING)	-	0	-
23.4(ARMOURING)	-	0	-
24.1(OUTER SHEATH)	-	0	-
24.2(Thickness of Outer Sheath)	-	500	-
24.3(Tolerance on Thickness of Outer Sheath)	-	0	-
24.4(OUTER SHEATH)	-	0	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	0	-
27.2(Bending test followed by partial discharge test;)	-	35000	Additional charge, if applicable
27.4(Dielectric power factor test)	-	25000	Additional charge, if applicable
27.5(Heating cycle test followed by partial discharge test;)	-	45000	Additional charge, if applicable
27.6(Impulse voltage test; and)	-	35000	Additional charge, if applicable
26.3(Special Provisions)	-	0	-
27.8(Flammability Test)	-	3500	-
27.9(Water Absorption Test)	-	7500	-
28(IDENTIFICATION)	-	0	-
29.1(PACKING AND MARKING)	-	0	-
29.2(PACKING AND MARKING)	-	0	-
30(BIS CERTIFICATION MARKING)	-	0	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	25000	Additional charge, if applicable
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	5500	-
Table 33(j), Cl. No. 27.4(Dielectric Power Factor (as a function of Voltage))	-	0	-
Table 33(h), Cl. No. 27.2(Partial discharge test)	-	0	-
Table 33(f)(Insulation resistance)	-	3500	-
Table 33(e)(Tear resistance on sheath)	-	5500	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	2500	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	2500	-
Table 33(e)(Permanent set on Sheath)	-	0	-
Table 33(e)(Hot set on Sheath)	-	2500	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	2500	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	2500	-
Table 33(e)(Elongation at break on Sheath)	-	2500	-
Table 33(e)(Tensile strength on Sheath)	-	2500	-
Table 33(d)(Ozone resistance on Insulation)	-	12500	Additional charge, if applicable
Table 33(d)(Permanent set on Insulation)	-	0	-
Table 33(d)(Hot set on Insulation)	-	4000	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	4000	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	4000	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	2500	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	2500	-
Table 33(d)(Elongation at break on Insulation)	-	1000	-
Table 33(d)(Tensile strength on Insulation)	-	1000	-
Table 33(b)(Diameter of armour wire)	-	500	-
Table 4(Copper purity test)	-	9000	Additional charge, if applicable
Table 33(a)(Conductor resistance test)	-	2500	-
Table 33(a)(Annealing test)	-	1000	-
Table 33(c)(Resistivity of steel wire)	-	1000	-

03 Apr, 2027

-
-

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

190000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTOR)	-	0	-
4.1.1(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	Complete testing Charge : Rs.1,90,000/- for Single core cable; Rs.2,40,000/- for Three core cable up to 19/33 kV. and Rs.4,20,000/- for Single core cable; Rs.6,25,000/- for Three core cable for 33/33 kV.
6(SCREENING)	-	0	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	0	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	0	-
7(FILLERS AND INNER SHEATH)	-	0	-
8.1(ARMOURING)	-	0	-
8.2(ARMOURING)	-	0	-
9(OUTER SHEATH )	-	0	-
10.1(CONDUCTOR)	-	0	-
10.2(CONDUCTOR)	-	0	-
11(CONDUCTOR SCREENING)	-	0	-
12.1(INSULATION)	-	0	-
12.2(INSULATION : Thickness of Insulation)	-	2500	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	0	-
12.4(Eccentricity and Ovality)	-	2500	-
12.5(INSULATION : Application of Insulation)	-	0	-
13.1(INSULATION SCREENING)	-	0	-
13.2(INSULATION SCREENING)	-	0	-
13.3(INSULATION SCREENING)	-	0	-
13.4(INSULATION SCREENING)	-	0	-
14.1(CORE IDENTIFICATION)	-	25000	Additional Charge, Rs 25000/- for each additional Core
14.1.1(CORE IDENTIFICATION)	-	0	-
15.1(LAVING UP OF CORES)	-	0	-
16.1(INNER SHEATH (COMMON COVERING))	-	0	-
16.2(INNER SHEATH (COMMON COVERING))	-	0	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	0	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	500	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	0	-
17.1(ARMOURING : Application )	-	0	-
17.1.1(ARMOURING )	-	0	-
17.1.2(ARMOURING )	-	0	-
17.1.3(ARMOURING )	-	0	-
17.2(ARMOURING : Type of armour )	-	0	-
17.2.1(ARMOURING : Type of armour )	-	0	-
17.2(ARMOURING : Coverage )	-	1500	-
17.3(ARMOURING : Dimension )	-	1000	-
17.4(ARMOURING : Joints)	-	0	-
16.4(ARMOURING : Resistance)	-	3500	-
18.1(OUTER SHEATH)	-	0	-
18.2(OUTER SHEATH: Colour)	-	0	-
18.3(Thicknes of outer sheath : average )	-	500	-
18.3(Thicknes of outer sheath : minimum )	-	0	-
19.1 i) a)(Annealing test (for copper))	-	2500	Charge, as applicable
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	2500	Charge, as applicable
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	0	-
19.1 i) c)(Wrapping test ( for aluminium))	-	0	-
19.1 i) d)(Resistance test - Main conductor )	-	3500	-
19.1 i) d)(Resistance test - Neutral conductor )	-	0	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	1500	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	1000	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2500	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2500	-
19.1 iii) c)(Degree of cross linking )	-	0	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	4000	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	0	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	2500	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	5500	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	1000	-
19.1 v) b)(Volume resistivity)	-	4500	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	1500	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	1000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2500	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2500	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	1000	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
19.1 vi) d)(Sheath : Hot deformation)	-	2000	-
19.1 vi) e)(Loss of massIn air oven)	-	2000	-
19.1 vi) f)(Sheath : Heat shock test)	-	2000	-
19.1 vi) g)(Sheath : Thermalstability)	-	1000	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	3500	Additional charges, If Applicable
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	2500	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	2500	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	2500	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	3500	-
20.2(Partial discharge test)	-	20000	-
20.3(Bending test)	-	5000	-
20.4(Dielectric power factor test : As a function of voltage)	-	7000	-
20.4(Dielectric power factor test : As a function of temperature)	-	5000	-
20.5(Heating Cycle Test)	-	25000	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	20000	Additional charges, If Applicable
20.7(High voltage test)	-	10000	-
20.8(Flammability test)	-	3500	-
20.1(Oxygen Index Test)	-	2500	Additional Charge, if applicable
20.11(Flame Retardance Test on Single Cables)	-	2500	-
20.12(Flame Retardance Test on Bunched Cables)	-	10000	Additional Charge, if applicable
20.13(Test for Halogen Acid Gas Evolution)	-	4000	Additional Charge, if applicable
20.14( Test for Smoke Density)	-	4500	Additional Charge, if applicable
20.15(Temperature Index)	-	0	Additional Charge, if applicable
21.1(IDENTIFICATION : Manufacturer's Identification)	-	0	-
21.2(IDENTIFICATION : Cable Identification)	-	0	-
21.3(IDENTIFICATION : Cable Code)	-	0	-
20.3 (a)(Partial discharge test (Bending test))	-	0	-
20.5 (a)(PD test (heating cycle test))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	20000	as applicable.
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	20000	as applicable.
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	20000	as applicable.
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	20000	as applicable.

03 Apr, 2027

-
-

IS 1180 : Part 1 (2014)

Outdoor Type Oil Immersed Distribution Transformers Upto and Including 2 500 kVA, 33kV - Specification Part 1 Mineral Oil Immersed (Fourth Revision)

Mineral Oil Immersed Distribution Transformers

120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.2 a)(Measurement of winding resistance )	-	6000	Complete Testing Charges : Rs.76000/- For 0 to 100 kVA, Rs.86100/- For 100 to 250 kVA, Rs.92000- For 250 kVA to 630 kVA, Rs.93100/- For 630 kVA to 1000 kVA, Rs.117900/- For 1000 kVA to 1600 kVA. Rs.120000/- For 1600 kVA to 2500 kVA.
21.2 b)( Measurement of voltage ratio and check of phase displacemen)	-	5000	-
21.2 c)( Measurement of short-circuit impedance (principal tapping, when applicable) and load loss at 50 percent and 100 percent load)	-	5000	-
21.2 d)(Measurement of no-load loss and current)	-	3500	-
21.2 e)(Measurement of insulation resistance)	-	2000	-
21.2 f)(Induced over-voltage withstand test)	-	4500	-
21.2 g)( Separate-source voltage withstand test)	-	4000	-
21.5.1.2(Pressure test-routine test (For Transformers up to 200 kVA ))	-	4000	-
21.5.1.3(Oil leakage test upto 200 KVA)	-	3000	-
21.3(a )(Lightning impulse test)	-	38000	-
21.3(b)(Temperature-rise test)	-	23000	-
21.5.1.1(Pressure test-Type test (For Transformers up to 200 kVA ))	-	6000	-
21.4 a)( Determination of sound levels)	-	6000	-
21.4 c(No load current at 112.5 percent voltage.)	-	1000	-
21.4 d(Paint adhesion tests)	-	1500	-
21.4 e(BDV and moisture content of oil in the transformer)	-	1500	-
6.9(Permissible Flux Density and Over Fluxing )	-	6000	-
13.1(Marking (Rating Plates))	-	0	-
13.2(Terminal Marking Plate)	-	0	-
13.3(Marking )	-	0	-
13.4(Marking)	-	0	-
13.4.1(Marking)	-	0	-
14.1(MOUNTING ARRANGEMENT)	-	0	-
14.2(MOUNTING ARRANGEMENT)	-	0	-
14.3(MOUNTING ARRANGEMENT)	-	0	-
14.4(MOUNTING ARRANGEMENT)	-	0	-
15.1.1(TRANSFORMER TANK : Construction)	-	0	-
15.1.2(TRANSFORMER TANK : Construction)	-	0	-
15.1.3(TRANSFORMER TANK : Construction)	-	0	-
15.1.4(TRANSFORMER TANK : Construction)	-	0	-
15.1.5(TRANSFORMER TANK : Construction)	-	0	-
21.5.3.3(Oil leakage test)	-	0	-
21.5.2.1(Type test : For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	120000	-
21.5.2.2(routine test :For Transformers Above 200 kVA and Up to Including 2 500 kVA)	-	37000	Routine Testing Charges : Rs.19100/- For 0 to 100 kVA, Rs.22200/- For 100 to 250 kVA, Rs.24700/- For 250 kVA to 630 kVA, Rs.25600/- For 630 kVA to 1000 kVA, Rs.33100/- For 1000 kVA to 1600 kVA. Rs.37000/- For 1600 kVA to 2500 kVA.
21.5.2.3( Oil leakage test (routine test))	-	0	-
21.5.3.1(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (type test))	-	0	-
21.5.3.2(For Single Phase Distribution Transformers Up to Including 25 kVA : pressure test (routine test))	-	0	-
21.5.3.3(Oil leakage test (routine test))	-	0	-
15.5(Total Dry Film Paint Thickness)	-	0	-
6.9, 7.9, 8.9(Permissible Flux Density and Over Fluxing)	-	0	-
11(Minimum clearance in Air)	-	0	-
16(Conservator for Non-sealed type Transformers)	-	0	-
20(Fittings)	-	0	-
6.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
7.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
8.8 (50%)(Total losses at 50 % load (Watts))	-	0	-
6.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
7.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
8.8 (100%)(Total losses at 100 % load (Watts))	-	0	-
9.1a)(CRGO Electrical Steel)	-	0	-
9.1 b)(Amorphous core material)	-	0	-
9.1 c)(Copper/Aluminium conductor)	-	0	-
9.1 d)(Kraft paper)	-	0	-
9.1 e)(Press Board)	-	0	-
9.1 f)(Mineral oil)	-	0	-
10(Terminal Arrangement)	-	0	-
15.2(Pressure and Vacuum Requirements)	-	0	-
15.4(Gasket)	-	0	-
19(Tolerances)	-	0	-
18(Efficiency and regulation)	-	0	-
4(Service Conditions)	-	0	-
5(General )	-	0	-
6.1(Rating)	-	0	-
6.2(Rated frequency)	-	0	-
6.3(Nominal system voltage)	-	0	-
6.4(Basic Insulation level )	-	0	-
6.5(No-Load Voltage Ratios)	-	0	-
6.6(Winding connections and phase displacement)	-	0	-
6.7(Tapping Range and Tapping Method)	-	0	-
6.8(Losses and impedance values)	-	0	-
6.1(Limits of Temperature-rise)	-	0	-
7(Technical Parameters of three phase distribution trasnformers higher than 200kva)	-	0	-
8(Technical Parameters of single phase distribution transformers UP to and including 25 KVA )	-	0	-
9(Standard Materials)	-	0	-
10(Terminal arrangment )	-	0	-
11(Minimum Clearnaces air )	-	0	-
12(Connectors )	-	0	-
13(Marking )	-	0	-
14(Mounting arrangement)	-	0	-
15(Trasnformer Tank )	-	0	-
16(Conservator for Non-Sealed type Transformers)	-	0	-
18(Efficiency and Regulation)	-	0	-
19(Tolerances)	-	0	-
21(General )	-	0	-
22(Information required with enquiry and order )	-	0	-
20(Fittings)	-	0	-

03 Apr, 2027

-
Exclusion: Cl.21.4 b (Short-circuit withstand test IS 2026 (Part 5) (above 200 kVA)), Cl. 17 ( ABILITY OF TRANSFORMERS TO WITHSTAND EXTERNAL SHORT CIRCUIT), Cl. 21.3(c) (Short-circuit withstand test)

IS 335 (2018)

New insulating oils - Specification (Fifth Revision)

New Insulating Oils

42700.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Viscosity)	-	3000.00	-
6.2(Pour Point)	-	1000.00	-
5.1(Classification)	-	0.0	-
5.2(Requirements)	-	0.0	-
5.3(Miscibility)	-	0.0	-
6.0(General)	-	0.0	-
6..3(Water Content)	-	1500.00	-
6.4(Breakdown Voltage)	-	1700.00	-
6.5(Dielectric Dissipation Factor (DDF))	-	2000.00	-
6.6(Appearance)	-	500.00	-
6.7(Acidity)	-	1000.00	-
6.8(Interfacial Tension (IFT))	-	1000.00	-
6.9(Sulphur Content)	-	2000.00	-
6.1(Corrosive Sulphur and Potentially Corrosive Sulphur)	-	1000.00	-
6.11(Additives)	-	5000.00	-
6.12(Oxidation Stability)	-	0.0	-
6.13(Gassing Tendency)	-	1500.00	-
6.15(Flash Point)	-	1000.00	-
6.16(Density)	-	1000.00	-
6.17(Polycyclic Aromatics (PCA))	-	2500.00	-
6.18(Polychlorinated Biphenyls (PCB))	-	2500.00	-
6.19(2-Furfural (2-FAL) and Related Compounds Content)	-	2500.00	-
6.2(Particle Content)	-	2000.00	-
6.21(DBDS Content)	-	2000.00	-
7.1 (a)(Total acidity)	-	1000.00	-
7.1 (b)(Sludge)	-	1000.00	-
7.1 (c)(DDF at 90°C)	-	2000.00	-
7.1 (d)(Total sulphur content)	-	0.0	-
4, 5.1.3, 6.1, Table 1(LCSET)	-	0.0	-
4, 5.1.3, 6.1, Table 1(Maximum Viscosity)	-	0.0	-
4, 5.1.3, 6.1, Table 1(Maximum Pour Point)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at 40°C)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at 0°C)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at -30°C)	-	0.0	-
4, 5.2, 6, Table 2(Viscosity at -40°C)	-	0.0	-
4, 5.2, 6, Table 2(Pour point)	-	0.0	-
4, 5.2, 6, Table 2(Water content)	-	0.0	-
4, 5.2, 6, Table 2(Breakdown voltage)	-	0.0	-
4, 5.2, 6, Table 2(DDF at 90°C)	-	0.0	-
4, 5.2, 6, Table 2(Particle content)	-	0.0	-
4, 5.2, 6, Table 2(Appearance)	-	0.0	-
4, 5.2, 6, Table 2(Acidity)	-	0.0	-
4, 5.2, 6, Table 2(Interfacial tension)	-	0.0	-
4, 5.2, 6, Table 2(Total sulphur content)	-	0.0	-
4, 5.2, 6, Table 2(Corrosive sulphur)	-	0.0	-
4, 5.2, 6, Table 2(Potentially corrosive sulphur)	-	0.0	-
4, 5.2, 6, Table 2(DBDS)	-	0.0	-
4, 5.2, 6, Table 2(Inhibitors according to IS 13631/IEC 60666)	-	0.0	-
4, 5.2, 6, Table 2(Metal passivator additives according to IS 13631/IEC 60666)	-	0.0	-
4, 5.2, 6, Table 2(Other additives)	-	0.0	-
4, 5.2, 6, Table 2(2-Furfural and related compounds content)	-	0.0	-
4, 5.2, 6, Table 2(Oxidation stability)	-	0.0	-
4, 5.2, 6, Table 2(Total acidity)	-	0.0	-
4, 5.2, 6, Table 2(Sludge)	-	0.0	-
4, 5.2, 6, Table 2(DDF at 90°C)	-	0.0	-
4, 5.2, 6, Table 2(Gassing tendency)	-	0.0	-
4, 5.2, 6, Table 2(Flash point)	-	0.0	-
4, 5.2, 6, Table 2(PCA content)	-	0.0	-
4, 5.2, 6, Table 2(PCB content)	-	0.0	-
6.22(Stray Gassing of Oil)	-	4000.00	-
7.3(Gassing Tendency)	-	0.0	-
4, 5.2, 6, Table 2(Density at 20°C)	-	0.0	-

03 Apr, 2027

-
Exclusion: Cl. 6.14 (Electrostatic Charging Tendency (ECT)), Cl. 7.2 (Electrostatic Charging Tendency (ECT)), Cl. 4, 5.2, 6, Table 2 (ECT)

IS 191 (2007)

Copper - Specification (Fourth Revision)

9000.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 - Table 4(Antimony-IS440)	-	500.00	-
7.1 - Table 4(Arsenic- IS440)	-	500.00	-
7.1 - Table 4(Bismuth-IS 440)	-	500.00	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	500.00	-
7.1 - Table 4(Iron IS 440)	-	500.00	-
7.1 - Table 4(Lead IS 440)	-	500.00	-
7.1 - Table 4(Nickel IS 440)	-	500.00	-
7.1 - Table 4(Oxygen IS 440)	-	500.00	-
7.1 - Table 4(Phosphorus- IS 440)	-	500.00	-
7.1 - Table 4(Silver- IS 440)	-	500.00	-
7.1 - Table 4(Sulphur- IS 440)	-	500.00	-
7.1 - Table 4(Tin - IS 440)	-	500.00	-
7.1 - Table 4(Tellurium- IS 440)	-	500.00	-
7.1 - Table 4(Selenium - IS 440)	-	500.00	-
7.1 - Table 4(Znic-IS 440)	-	500.00	-
4-Table 1(GRADES/DESIGNATIONS)	-	0.0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0.0	-
5.1- Table 2(L)	-	0.0	-
5.1- Table 2(L1)	-	0.0	-
5.1- Table 2(h)	-	0.0	-
5.1- Table 2(h1)	-	0.0	-
5.1- Table 2(b)	-	0.0	-
5.1- Table 2(b1)	-	0.0	-
5.1- Table 2(R)	-	0.0	-
5.1- Table 2(R1)	-	0.0	-
5.1- Table 2(R2 )	-	0.0	-
5.1- Table 2(α )	-	0.0	-
5.1- Table 2( β )	-	0.0	-
5.1- Table 2(γ)	-	0.0	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	0.0	-
7.1 - Table 4(Total Impurities- IS 440)	-	0.0	-
5.2(Billets)	-	0.0	-
5.4-Table 3 (For Billets)(Mass)	-	0.0	-
5.2-Table 3 (For Billets)(Diameter)	-	0.0	-
5.2-Table 3 (For Billets)(Length)	-	0.0	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	0.0	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Ingots)(Mass)	-	0.0	-
5.4-Table 3 (Cast cakes)(Mass)	-	0.0	-
5.3-Table 3 (Cast cakes)(Width)	-	0.0	-
5.3-Table 3 (Cast cakes)(thickness )	-	0.0	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	0.0	-
8.1(FREEDOM FROM DEFECTS)	-	0.0	-
8.2(FREEDOM FROM DEFECTS)	-	0.0	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	0.0	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	1000.00	-
4-Table 1(GRADES/DESIGNATIONS)	-	0.0	-
5.1- Table 2(L)	-	0.0	-
5.1- Table 2(L1)	-	0.0	-
5.1- Table 2(h)	-	0.0	-
5.1- Table 2(h1)	-	0.0	-
5.1- Table 2(b)	-	0.0	-
5.1- Table 2(b1)	-	0.0	-
5.1- Table 2(R)	-	0.0	-
5.1- Table 2(R1)	-	0.0	-
5.1- Table 2(R2 )	-	0.0	-
5.1- Table 2(α )	-	0.0	-
5.1- Table 2( β )	-	0.0	-
5.1- Table 2(γ)	-	0.0	-
5.2(Billets)	-	0.0	-
5.4-Table 3 (For Billets)(Mass)	-	0.0	-
5.2-Table 3 (For Billets)(Diameter)	-	0.0	-
5.2-Table 3 (For Billets)(Length)	-	0.0	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	0.0	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	0.0	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	0.0	-
5.4-Table 3 (Ingots)(Mass)	-	0.0	-
5.4-Table 3 (Cast cakes)(Mass)	-	0.0	-
5.3-Table 3 (Cast cakes)(Width)	-	0.0	-
5.3-Table 3 (Cast cakes)(thickness )	-	0.0	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	0.0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0.0	-
7.1 - Table 4(Silver- IS 440)	-	0.0	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	0.0	-
7.1 - Table 4(Phosphorus- IS 440)	-	0.0	-
7.1 - Table 4(Arsenic- IS440)	-	0.0	-
7.1 - Table 4(Antimony-IS440)	-	0.0	-
7.1 - Table 4(Bismuth-IS 440)	-	0.0	-
7.1 - Table 4(Iron IS 440)	-	0.0	-
7.1 - Table 4(Lead IS 440)	-	0.0	-
7.1 - Table 4(Nickel IS 440)	-	0.0	-
7.1 - Table 4(Oxygen IS 440)	-	0.0	-
7.1 - Table 4(Selenium - IS 440)	-	0.0	-
7.1 - Table 4(Sulphur- IS 440)	-	0.0	-
7.1 - Table 4(Tellurium- IS 440)	-	0.0	-
7.1 - Table 4(Tin - IS 440)	-	0.0	-
7.1 - Table 4(Znic-IS 440)	-	0.0	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	0.0	-
7.1 - Table 4(Total Impurities- IS 440)	-	0.0	-
8.1(FREEDOM FROM DEFECTS)	-	0.0	-
8.2(FREEDOM FROM DEFECTS)	-	0.0	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	0.0	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	0.0	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	500.00	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	0.0	-
13(Marking)	-	0.0	-
13(Marking)	-	0.0	-
13(Marking)	-	0.0	-

03 Apr, 2027

-
-

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

174000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	1500	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	1000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	1000	Additional charges, If applicable
IS 191:2007 & IS 440(Copper purity test)	-	9000	Additional charges, If applicable
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	1500	Additional charge, Rs. 2000 /- For each additional core
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	1500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	1000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	1500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	2500	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	1500	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	1500	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	2500	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	1500	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	2500	Not applicable for thermoset material
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	2500	Not applicable for thermoset material
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	3500	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	1500	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	4000	Additional charges, If applicable (For Insulation)
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	4000	Additional charges, If applicable (For Insulation)
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	6000	Additional charges, If applicable (For Insulation)
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	21000	Additional charges, If applicable (For Insulation)
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	3000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	3000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	12500	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	3000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	4000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	4000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	6000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	21000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	2500	Not applicable for thermoset material
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	2500	Not applicable for thermoset material
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	0	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	1500	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	0	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	2500	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	2000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	0	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	5500	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	10000	Smoke density test (3-meter cube)
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	45000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	1500	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	5500	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	8500	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	5500	-

03 Apr, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

RTRC LIMITED, GURUGRAM

Plot No. 296, Sector-7, Phase-II,Industrial Estate,IMT Manesar, Gurugram, Gurugram, Gurugram, Haryana, 122050

8826495200 qa@rtrc.in

Scope List