BIS - LIMS (Laboratory Information Management System)

The Automotive Research Association of India

Survey no.102,Vetal hill,off Paud road,Kothrud, Pune, Pune, Maharashtra, 411038

9975581051 director@araiindia.com

Scope List

Reset

12 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 14900 (2018)

Transparent float glass - Specification (First Revision)

25677 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(A glass shall be deemed to be manufactured using float glass technology if the tin side of the glass can be identified by the UV light test as prescribed in Annex A.)	-	7247	Combined Test Charges for Clause No. 4.1, 4.4, 4.5 and 4.6
Cl.4.2 ( Annexure B Table 1)(The minimum value for visual light transmission for a flat, transparent clear float glass, when measured as per Annex B, shall be as prescribed in Table 1)	-	6268	-
Cl.4.3.1 (Table 2)(Float glass thickness shall be measured with micrometer or calipers, which is graduated to 0.01 mm or with a measuring instrument having an equivalent accuracy. The tolerances on thickness shall be as specified in Table 2.)	-	6149	-
Cl.4.3.2.1 (the finished pane shall not be larger than a prescribed rectangle of dimensions (W + v, L + v), or smaller than a prescribed rectangle of dimensions (W – v, L – v), where v is the maximum tolerance on nominal dimensions. The corresponding sides of the prescribed rectangles shall be parallel to each other and these rectangles shall have a common centre (see Fig.1).)	-	6013	Combined Test Charges for Clause No. 4.3.2 and 4.3.3
Cl.4.3.2.2(The length and width of the glass on cut sizes shall be measured with a steel scale (tape) which is graduated to 1 mm. The measurement shall be made on adjacent two sides. The tolerances on nominal dimensions length L, and width W, shall be ± 5mm.)	-	6013	Combined Test Charges for Clause No. 4.3.2 and 4.3.3
Cl.4.3.3(The tolerances on diagonals shall be as specified in Table 3.)	-	6013	Combined Test Charges for Clause No. 4.3.2 and 4.3.3
Cl.4.4 (Annex C Table 8)(The glass shall be viewed under the conditions of observation as described in Annex C, and the angle at which there is no optical distortion shall be noted. This angle shall not be less than the appropriate critical viewing angle (see Table 8).)	-	7247	Combined Test Charges for Clause No. 4.1, 4.4, 4.5 and 4.6
Cl.4.5.1(see Table 4(Spot faults are categorized based on their size (see Table 4). Determination of spot faults shall be done in accordance with Annex D. The maximum permissible number of the different categories of spot faults shall be as per Tables 5 and 6.)	-	7247	Combined Test Charges for Clause No. 4.1, 4.4, 4.5 and 4.6
Cl.4.5.2(Annexure E)(There shall be no reams, strings and lines distinguished visually when tested in accordance with Annex E.)	-	7247	Combined Test Charges for Clause No. 4.1, 4.4, 4.5 and 4.6
Cl.4.5.3(Annexure E)(There shall not be any linear/extended faults when tested in accordance with Annex E.)	-	7247	Combined Test Charges for Clause No. 4.1, 4.4, 4.5 and 4.6
Cl.4.6(Fig.2)(Defects in shape such as chipping of cut side, shelling, protrusion, slicing off, corners on/off, etc as shown in Fig. 2 shall be such that the deviation from the cutting line when viewing perpendicularly to the surface of plate glass is not more than the nominal value of thickness of glass or 10 mm, whichever is smaller.)	-	7247	Combined Test Charges for Clause No. 4.1, 4.4, 4.5 and 4.6

Complete

IS 2835 (1987)

Specification for flat transparent sheet glass (Third Revision)

25774 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CLASSIFICATION)	-	0	Required to be provided along with samples.
4.1(Material)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.1.1(Material)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.2-Table 1 & Cl 5.1(Thickness )	-	6149	-
4.2-Table 1(Length )	-	6013	Combined charges for Length and Width.
4.2-Table 1(Width)	-	6013	Combined charges for Length and Width.
4.3-Table 2-i(Gaseous inclusion)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3-Table 2-ii(Opaque gaseous inclusion)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3-Table 2-iii(Knots, dirts and stones)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3-Table 2-iv & Cl 5.2(Scratches, rubs and crush)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3-Table 2-v & Cl 5.3(Bow)	-	7708	-
4.3-Table 2-vi & Cl 5.4(Reams, Light Strings and lines)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3-Table 2-vii(Waviness)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3-Table 2-viii(Sulphur stains)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3-Table 2-ix(Corner breakage and chip)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Central area)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3.1-Table 2A-i(Allowable Cluster of Defects for AA Quality at Outer area)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Central area)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3.1-Table 2A-ii(Allowable Cluster of Defects for A Quality at Outer area)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Central area)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
4.3.1-Table 2A-iii(Allowable Cluster of Defects for B Quality at Outer area)	-	5904	Combined charges for Clause 4.1, 4.3, 5.2 and 5.4
3.1(CLASSIFICATION)	-	0	Required to be provided along with samples.

Complete

IS 16192 : Part 1 (2014)

Automotive vehicles - Wheel rims for two and three wheeled vehicles: Part 1 light alloy wheel rims - Method of tests and requirements

192500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.1(Rotation Bending Fatigue Test (Dynamic Cornering Fatigue Test))	-	62000	2W CFT charges with Marking
4.2.2(Rotation Bending Fatigue Test (Dynamic Cornering Fatigue Test) No. of cycle 105)	-	62000	CFT
4.3.1(Radial Load Durability Test)	-	67000	RFT
4.3.2(Radial load durability tests ,No of cycle 5 x 105)	-	67000	RFT
4.4.1(Radial Impact Resistance Test)	-	15000	Impact
4.4.2(Radial Impact Resistance Test)	-	15000	Impact
4.5.1(Torsion Moment Test)	-	45000	Torsion Test
4.5.2(Torsion Moment Test no of cycle is required 105 )	-	45000	Torsion test
4.6.1(Air Leak Test (Tubeless Tyres Wheel Rim))	-	10000	Air Leak test
4.6.2(Air Leak Test (Tubeless Tyres Wheel Rim), 2 minutes)	-	10000	Air Leak test

Complete

IS 16192 : Part 2 (2014)

Automotive vehicles - Wheel rims for two and three wheeled vehicles: Part 2 sheet metal wheel rims - Method of tests and requirements

103000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3.4(a) For three wheeled vehicles: 18000 load cycle)	-	32000	3W CFT charges with Marking
4.2.3.4(b) For two wheeled vehicles:no of cycle 105 )	-	32000	2W CFT charges with Marking
4.2.4(Dynamic Radial Fatigue Test (RFT))	-	71000	RFT

Complete

IS 9438 (2018)

Performance requirements and methods of tests for wheels/ rims for trucks and buses (First Revision)

210000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1 table 1(cl 5.2 dynamic radial Fatigue test (For Disc Wheels and wheels with Demountable Rims, Test factors for dynamic Radial Fatigue Test Loading method and Minimum No.of Performnace cycle clause 5.2.2 and 5.2.4 table 2)	-	52000	CFT
Cl 5.1 table 1 i)(material Ferrous rim diametre 13 Accelerated test Factor 1.60)	-	52000	CFT
Cl 5.1 table 1 i)(material Ferrous rim diametre 14 Accelerated Test Factor 1.60)	-	52000	CFT
Cl 5.1 table 1 i)(material Ferrous rim diametre 15 Accelerated Test Factor 1.60)	-	52000	CFT
Cl 5.1 table 1 ii)(material Ferrous rim diametre 16 and aboveAccelerated Test Factor 1.45)	-	52000	CFT
Cl 5.1 table 1 iii)(material Ferrous rim any diametreAccelerated Test Factor 1.10)	-	52000	CFT
Cl 5.1 table 1 ii)(material Ferrous rim any diametre and above Accelerated Test Factor 1.30)	-	52000	CFT
Cl 5.1 table 1 iv)(material Alluminum rim diametre 16 and above Accelerated Test Factor 1.35)	-	62000	CFT
Cl 5.1 table 1 iv)(material Alluminum rim diametre 16 and above Accelerated Test Factor 1.63)	-	62000	CFT
Cl 5.1 table 1 v)(material Alluminum rim diametre 17.5 and larger Accelerated Test Factor 1.35)	-	62000	CFT
Cl.5.2 table 2(Cl 5.2 dynamic radial Fatigue test (For Disc Wheels and wheels with Demountable Rims, Test factors for dynamic Radial Fatigue Test Loading method and Minimum No.of Performnace cycle clause 5.2.2 and 5.2.4 table 2)	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 13 (5˚˚ drop centre) Accelerated Test Factor 2.2, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 13 and (5˚˚ drop centre) Accelerated Test Factor 1.8, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 14 and (5˚˚ drop centre) Accelerated Test Factor 2.2, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 14 and (5˚˚ drop centre) Accelerated Test Factor 1.8, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 15 and (5˚˚ drop centre) Accelerated Test Factor 2.2, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 15 and (5˚˚ drop centre) Accelerated Test Factor 1.8, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 16 and (5˚˚ drop centre) Accelerated Test Factor 2.2, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 17 and (5˚˚ drop centre) Accelerated Test Factor 2.2, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 i(Material Ferrous rim diametre 17 and (5˚˚ drop centre) Accelerated Test Factor 1.8, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 15 Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 15 and Accelerated Test Factor 1.9 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 15 and Accelerated Test Factor 1.8 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 15 and Accelerated Test Factor 1.7 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 15 and Accelerated Test Factor 1.6 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17 and Accelerated Test Factor 2.0, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17 and Accelerated Test Factor 1.9, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17 and Accelerated Test Factor 1.8, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17 and Accelerated Test Factor 1.7, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17 and Accelerated Test Factor 1.6, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 18 and Accelerated Test Factor 2.0, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 18 and Accelerated Test Factor 1.9, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 18 and Accelerated Test Factor 1.8, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 18 and Accelerated Test Factor 1.7, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 20 and Accelerated Test Factor 1.6, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 20 and Accelerated Test Factor 2.0, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 20 and Accelerated Test Factor 1.9 (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 20 and Accelerated Test Factor 1.8 (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22 and Accelerated Test Factor 2.0, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24 and Accelerated Test Factor 1.9 , (Inset or Outset - All ))	-	68000	RFt
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22 and Accelerated Test Factor 1.8, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22 and Accelerated Test Factor 1.7, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22 and Accelerated Test Factor 1.6, (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24 and Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24 and Accelerated Test Factor 1.8 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24 and Accelerated Test Factor 1.7 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24 and Accelerated Test Factor 1.6 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17.5 HC and Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17.5 HC and Accelerated Test Factor 1.9 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17.5 HC and Accelerated Test Factor 1.8 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17.5 HC and Accelerated Test Factor 1.7 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 17.5 HC and Accelerated Test Factor 1.6 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 19.5 and Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 19.5 and Accelerated Test Factor 1.9 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 19.5 and Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 19.5 and Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22.5 and Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22.5 and Accelerated Test Factor 1.9 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22.5 and Accelerated Test Factor 1.8 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22.5 and Accelerated Test Factor 1.7 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 22.5 and Accelerated Test Factor 1.6 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24.5 and Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24.5 and Accelerated Test Factor 19 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24.5 and Accelerated Test Factor 1.8 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24.5 and Accelerated Test Factor 1.7 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 ii)(Material Ferrous rim diametre 24.5 and Accelerated Test Factor 1.6 , (Inset or Outset - All ))	-	68000	RFT
Cl.5.2 table 2 iii)(Material Aluminium rim diametre 16 and Accelerated Test Factor 2.8 , (Inset or Outset - 127 or more ))	-	148000	RFT
Cl.5.2 table 2 iii)(Material Aluminium rim diametre 16 and Accelerated Test Factor 2.0 , (Inset or Outset - 127 or more ))	-	148000	RFT
Cl.5.2 table 2 iv)(Material Aluminium rim diametre 17.5 and larger . Accelerated Test Factor 2.8 , (Inset or Outset - All ))	-	148000	RFT
Cl.5.2 table 2 iv)(Material Aluminium rim diametre 17.5 and larger . Accelerated Test Factor 2.0 , (Inset or Outset - All ))	-	148000	RFT
Cl.5.3 table 3 (Cl 5.3 dynamic Cornering Fatigue test (For wheels with Demountable Rims), Test Load factors for Wheels with demountable Rims - Dynamic cornerning Fatigue test clause 5.3.4 and 5.3.5 table 3)	-	52000	CFT
Cl.5.3 table 3 i) (Accelerated test factor 1.9 Coefficient of friction 0.7)	-	52000	CFT
Cl.5.3 table 3 i) (Material Ferrous All, Accelerated test factor 1.5 Coefficient of friction 0.7)	-	52000	CFT
Cl 5.1 table 1(Cl.5.1 dynamic Cornering Fatigue test (For Disc Wheel Rims))	-	52000	CFT

Complete

IS 16192 : Part 3 (2018)

Automotive vehicles - Wheel rims for two and three wheeled vehicles: Part 3 Spoke Wheel Rims ---Method of tests and requirements

18360 View breakup
Excluding tax

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2(Strength Requirements refer table -1 & table -2)	-	64500		Full Test
4.2(Strength Requirements refer table -1 & table -2)	-	64500		Full Test

Complete

IS 9436 (2018)

Performance requirements and methodsof test for wheels for passenger cars, quadricycles and mini goods cariers (First Revision)

103000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1 table 2 (Cl 5.1 dynamic cornering fatigue test. Test factors and minimum cycle for requirements for wheels in normal Highway service dynamic cornering fatigue clause 5.1.3 5.1.4 and A-1 table 2)	-	32000	CFT- Ferrous
Cl 5.1 table 2 i)( ferrous all)	-	32000	CFT- Ferrous
Cl 5.1 table 2 ii)( cold formed aluminium 5000 series)	-	60000	CFT- AL
Cl 5.1 table 2 iii)( aluminium cast and forged)	-	60000	CFT- AL
Cl 5.1 table 4(Cl.5.2dynamic cornering fatigue test.table 4 factors and minimum cycle requirements for temporary use wheels clause5.1.4 Amd-1)	-	32000	CFT- Ferrous
Cl 5.1 table 4 i)( ferrous all)	-	32000	CFT- Ferrous
Cl 5.1 table 4 ii)( cold formed aluminium 5000 series)	-	60000	CFT- AL
Cl 5.1 table 4 iii)( aluminium cast and forged)	-	60000	CFT- AL
Cl.5.2 table 3(Cl 5.2 dynamic radial Fatigue testTest factors and minimum cycle for requirements for wheels in normal Highway service dynamic Radial fatigue test clause 5.2.3 5.2.4 and A-1 table 3)	-	71000	RFT- Ferrous
Cl 5.2 table 3 i)(ferrous all)	-	71000	RFT- Ferrous
Cl 5.2 table 3 i)(Alluminium All)	-	100750	RFT- AL
Cl.5.2 table 5(Cl 5.2 dynamic radial Fatigue test Test factors and minimum cycle for temporary use wheels Dynamic Radial fatigue test clause 5.2.4 and A-1 table 5)	-	71000	RFT- Ferrous
Cl 5.2 table 5 i)(ferrous all)	-	71000	RFT- Ferrous
Cl 5.2 table 5 i)(Alluminium All)	-	100750	RFT- AL

Complete

IS 15627 (2005)

Automotive vehicles - Pneumatic tyres i?or two and three - Wheeled motor vehicles - Specification

71250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1.1.1- Refer Annex C Col 2 and Annex D(test method )(Tyre dimensions/Section width)	-	6360	Dimension Test Charge. Charges are inclusive of all parameters of dimension test requirements
4/4.1.1.2- Refer Annex C Col 2 and Annex D(test method )(Tyre outer diameter)	-	6360	Charges are included in dimension test charge
4/4.2.1 /4.2.2/4.2.3,Annex E ,Table 12(Load/Speed Performance Test)	-	19200	Charges are inclusive of all parameters of Load/Speed Performance Test requirements
4/4.2.4(Outer diameter of the .tyre after the 6 hrs of the Load/Speed Performance Test shall not differ from the outer diameter measured before the test by more than + 3.5 percent.)	-	19200	Charges are included in Load/Speed Performance Test charge
4/4.2.5 Refer Annex C (The tyre overall width measured at the end of the load/speed performance test shall not exceed the value specified in 4.1.l.l(d) or 4.1.l.l(f) as applicable.)	-	6360	Charges are included in Load/Speed Performance Test charge
4.4,Refer Table 14 to 16 and Annex G(Tyre Strength Test (Plunger Test) )	-	10320	Charges are inclusive of all parameters of Tyre Strength Test (Plunger Test) requirements
4.5 refer Table 17 and Annex H(Endurance Test)	-	78000	Charges are inclusive of all parameters of Endurance Test requirements
4.6/4.6.1(Tread Wear Indicators)	-	6360	Charges are included in dimension test charge
4.6.2 Refer Annex D(Method of measurement)(Tread Wear Indicators)	-	6360	Charges are included in dimension test charge
4.6.3(Tread Wear Indicators)	-	6360	Charges are included in dimension test charge
5(Markings)	-	6360	-
5, Annex J(Arrangement of tyre markings)	-	6360	-

Complete

IS 15636 (2012)

Automotive vehicles - Pneumatic tyres for commercial vehicles - Diagonal and radial ply - Specification (First Revision)

94860 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 8(Marking)	-	6360	Dimension Test Charge. Charges are inclusive of all dimension test requirements
3.1.1(Type of pnuamitic tyre)	-	0	Charges are included in dimension test charge
3.17(Tyre-Size Designation)	-	0	Charges are included in dimension test charge
3.26(Load Index)	-	0	Charges are included in dimension test charge
3.28(Speed symbol)	-	0	Charges are included in dimension test charge
4.1.1(Section width of tyre)	-	0	Charges are included in dimension test charge
4.1.1.2(Tyre outer diameter)	-	0	Charges are included in dimension test charge
4.2(Endurance test)	-	78000	Charges are inclusive of all parameters of Endurance Test
4.3.1(Load/Speed performance test)	-	19200	Charges are inclusive of all parameters of Load/Speed performance Test
4,4,1(Tread -wear indicators)	-	0	Charges are included in dimension test charge
4.4,2(Tread -wear indicators)	-	0	Charges are included in dimension test charge
4.4.4(Tread -wear indicators)	-	0	Charges are included in dimension test charge
4.5(Tyre strength test (Plunger rest))	-	10320	Charges are inclusive of all parameters of Tyre strength test (Plunger test)

Complete

IS 15633 (2005)

Automotive vehicles - Pneumatic tyres for passenger car vehicles - Diagonal and radial ply - Specification

94860 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4/4.1.1.1- Refer Annex B Col 2 and Annex D(test method )(Tyre dimensions/Section width)	-	6360	Dimension Test Charge. Charges are inclusive of all dimension test requirements
4/4.1.1.2- Refer Annex B Col 2 and Annex D(test method )(Tyre outer diameter)	-	6360	Charges are included in dimension test charge
4/4.2.1 /4.2.2/4.2.3,Refer Annex D ,Table 13(Load/Speed Performance Test)	-	19200	Charges are inclusive of all parameters of load/speed performance tests requirements
4.2.4(Outer diameter of the .tyre after the 6 hrs of the Load/Speed Performance Test shall not differ from the outer diameter measured before the test by more than + 3.5 percent.)	-	6360	Charges are included in load/speed performance test charge
4.3/4.3.1/4.3.2 Refer Annex E and Table 14( Endurance Test)	-	78000	Charges are inclusive of all parameters of endurance test
4.4/4.4.1/4.4.2 Refer Annex F and Table 15 and 16(Bead Unseating Resistance Test for Tubeless Tyre )	-	8580	Charges are inclusive of all parameters of Bead Unseating Resistance Tests for Tubeless Tyre
4.5/4.5.1(Tread-Wear -Indicators)	-	6360	Charges are included in dimension test charge
4.5.2(Each tread-wear indicator shall individually provide a means of indicating with a tolerance of +0.60 ,−0.00 mm when the tread grooves are no longer more than 1.6 mm deep.’)	-	6360	Charges are included in dimension test charge
4.6. Refer Annex G ,Table 17 and 18(Tyre.Strength Test)	-	10320	Charges are inclusive of all parameters of Tyre.Strength Test
5(Markings)	-	6360	-
5.4, Annex J(Arrangement of tyre markings)	-	6360	-

Complete

IS/ISO 6742 : PART 2 (2015)

Cycles - Lighting and retro - Reflective devices: Part 2 retro - Reflective devices (First Revision)

48000 View breakup
Excluding tax

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 -Tables 4, 5, 6, 7, 8, 9 or 10(Reflectors-CIL value)	-	21504	--
6-Table 15( Colorimetric requirements)	-	10080	--
7.1.2.2(Reflectors-Temperature resistance test)	-	24600	--
7.1.2.3(Reflectors- Impact test (except for conventional reflector of Group A))	-	5000	--
7.1.2.4(Reflectors-Moisture resistance test)	-	5600	--
7.1.2.5(Reflectors- Resistance to fuels)	-	5088	--
7.1.2.6(Reflectors- Resistance to lubricating oils)	-	5088	--

Complete

IS 2553 : Part 1 (2018)

Safety glass - Specification: Part 1 architectural, building and general uses (Fourth Revision)

149727 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1 (Thickness -IS 17004 & IS 14900)	-	5124	Test Charges for thickness measurement
5.2.2.1( Dimensions- Width )	-	5011	Combined Test Charges for Dimension and Squareness
5.2.2.1( Dimensions- Length)	-	5011	Combined Test Charges for Dimension and Squareness
4(Types)	-	6039	Combined Test Charges for General Requirements
5.1.1(General)	-	6039	Combined Test Charges for General Requirements
5.1.2(Optical Faults-IS 14900)	-	6039	Combined Test Charges for General Requirements
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	6039	Combined Test Charges for General Requirements
5.1.2(Reams, Strings and Lines-IS 14900)	-	6039	Combined Test Charges for General Requirements
5.1.2(Linear / Extended Faults -IS 14900)	-	6039	Combined Test Charges for General Requirements
5.2.2.2( Squareness)	-	5011	Combined Test Charges for Dimension and Squareness
5.2.3 (Fragmentation Test- IS 17004)	-	6271	Test charges for Fragmentation Test
5.2.4-a( Flatness-Overall bow-IS 17004)	-	6423	Combined Test Charges for Flatness Test
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	6423	Combined Test Charges for Flatness Test
5.2.4-c( Flatness-Edge lift-IS 17006)	-	6423	Combined Test Charges for Flatness Test
5.2.4-d( Flatness-Local distortion-IS 17007)	-	6423	Combined Test Charges for Flatness Test
5.2.4.1 (Other distortions)	-	6423	Combined Test Charges for Flatness Test
5.2.5.1( Resistance to shock- IS 17004)	-	5571	Test Charges for Resistance to Shock Test
5.2.5.2( Resistance to human impact- IS 17004)	-	9998	Test Charges for Resistance to Human Impact Test
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	5380	Combined Test Charges for Fabrication in Glass
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	5380	Combined Test Charges for Fabrication in Glass
5.3.1 (Thickness-IS 17004 & IS 14900)	-	5124	Test Charges for Thickness Test
5.3.2.1( Dimensions and squareness- Width )	-	5149	Combined Test Charges for Dimension, Squareness and Edge Matching
5.3.2.1( Dimensions and squareness- Length)	-	5149	Combined Test Charges for Dimension, Squareness and Edge Matching
5.3.2.1( Dimensions and squareness-Squareness)	-	5149	Combined Test Charges for Dimension, Squareness and Edge Matching
5.3.2.2 (Edge displacement)	-	5149	Combined Test Charges for Dimension, Squareness and Edge Matching
5.3.3( Light Stability Test-IS 17004)	-	26840	Test Charges for Light Stability Test
5.3.4( Boil and Bake Tests-IS 17004)	-	8611	Combined Test Charges for Boil and Bake Test
5.3.4( Boil and Bake Tests-IS 17004)	-	8611	Combined Test Charges for Boil and Bake Test
5.3.5( Fracture and Adhesion Test-IS 17004)	-	7157	Test Charges for Fracture and Adhesion Test
5.3.6.1( Spot defects in the central area)	-	4920	Combined Test Charges for Defects in Central Area
5.3.6.2 (Linear defects in the central area)	-	4920	Combined Test Charges for Defects in Central Area
5.3.6.3( Defects in the outer area for framed edges)	-	4920	Combined Test Charges for Defects in Central Area
5.3.6.4( Vents)	-	4920	Combined Test Charges for Defects in Central Area
5.3.6.5( Creases and streaks)	-	4920	Combined Test Charges for Defects in Central Area
5.3.6.6( Defects on edge which will not be framed)	-	4920	Combined Test Charges for Defects in Central Area
5.3.7( Humidity Test – Optional)	-	80172	Test Charges for Humidity Test without condensation
5.3.8( Resistance to Human Impact Test)	-	9998	Test Charges for Resistance to Human Impact Test
4(Types)	-	-	-
5.1.1(General)	-	-	-
5.1.2(Optical Faults-IS 14900)	-	-	-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	-	-
5.1.2(Reams, Strings and Lines-IS 14900)	-	-	-
5.1.2(Linear / Extended Faults -IS 14900)	-	-	-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	-	-
5.2.2.1( Dimensions- Width )	-	-	-
5.2.2.1( Dimensions- Length)	-	-	-
5.2.2.2( Squareness)	-	-	-
5.2.3 (Fragmentation Test- IS 17004)	-	-	-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	-	-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	-	-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	-	-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	-	-
5.2.4.1 (Other distortions)	-	-	-
5.2.5.1( Resistance to shock- IS 17004)	-	-	-
5.2.5.2( Resistance to human impact- IS 17004)	-	-	-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	-	-
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	-	-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	-	-
5.3.2.1( Dimensions and squareness- Width )	-	-	-
5.3.2.1( Dimensions and squareness- Length)	-	-	-
5.3.2.1( Dimensions and squareness-Squareness)	-	-	-
5.3.2.2 (Edge displacement)	-	-	-
5.3.3( Light Stability Test-IS 17004)	-	-	-
5.3.4( Boil and Bake Tests-IS 17004)	-	-	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	-	-
5.3.6.1( Spot defects in the central area)	-	-	-
5.3.6.2 (Linear defects in the central area)	-	-	-
5.3.6.3( Defects in the outer area for framed edges)	-	-	-
5.3.6.4( Vents)	-	-	-
5.3.6.5( Creases and streaks)	-	-	-
5.3.6.6( Defects on edge which will not be framed)	-	-	-
5.3.7( Humidity Test – Optional)	-	-	-
5.3.8( Resistance to Human Impact Test)	-	-	-

Complete

Bureau of Indian Standards

The National Standards Body of India

The Automotive Research Association of India

Survey no.102,Vetal hill,off Paud road,Kothrud, Pune, Pune, Maharashtra, 411038

9975581051 director@araiindia.com

Scope List