BIS - LIMS (Laboratory Information Management System)

(suspended) Rajkot Metlab Services LLP, Rajkot

PL 29 30 Nr Tulip Party Plot, GONDAL ROAD, VAVDI, Rajkot, Rajkot, Gujarat, 360004

9725213602 testing@rajkotlab.com

Scope List

Reset

150 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 1363 : Part 3 (2018)

Hexagon Head Bolts, Screws and Nuts of Product Grade ˜C ™ Part 3 (Style 1) Hexagon Nuts ( Size Range M 5 to M 64 ) ( Fifth Revision )

All Grade / Type / Size / Designation / Class

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3-Table 1(Dimensions-D)	-	500	-
3-Table 1(Dimensions-P)	-	500	-
3-Table 1(Dimensions-dw(minimum))	-	500	-
3-Table 1(Dimensions-e(minimum))	-	500	-
3-Table 1(Dimensions-m(minimum))	-	500	-
3-Table 1(Dimensions-m(maximum))	-	500	-
3-Table 1(Dimensions-mw(minimum))	-	500	-
3-Table 1(Dimensions-s(minimum))	-	500	-
3-Table 1(Dimensions-s(maximum))	-	500	-
3-Table 2(Dimensions-D)	-	500	-
3-Table 2(Dimensions-P)	-	500	-
3-Table 2(Dimensions-dw(minimum))	-	500	-
3-Table 2(Dimensions-e(minimum))	-	500	-
3-Table 2(Dimensions-m(minimum))	-	500	-
3-Table 2(Dimensions-m(maximum))	-	500	-
3-Table 2(Dimensions-mw(minimum))	-	500	-
3-Table 2(Dimensions-s(minimum))	-	500	-
3-Table 2(Dimensions-s(maximum))	-	500	-
4-Table 3(General requirements)	-	500	-
4-Table 3(Threads-ISO 724 & 965(1))	-	2000	-
4-Table 3(Mechanical property-Property class (ISO 898-1))	-	5000	-
4-Table 3(Mechanical property-Tensile strength (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Lower yield strength (ISO 898-1) )	-	1000	-
4-Table 3(Mechanical property-Stress at 0,2 % non-proportional elongation (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Stress at 0,0048d non-proportional elongation for full-size fasteners (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Stress under proof load (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Proof strength ratio (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Percentage elongation after fracture for machined test pieces (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Percentage reduction of area after fracture for machined test pieces (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Elongation after fracture for full-size fasteners (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Head soundness (ISO 898-1))	-	1500	-
4-Table 3(Mechanical property-Vickers hardness (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Brinell hardness (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1) HRB)	-	1000	-
4-Table 3(Mechanical property-Rockwell hardness (ISO 898-1) HRC)	-	1000	-
4-Table 3(Mechanical property-Surface hardness (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Non-carburization (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Height of non-decarburized thread zone (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Depth of complete decarburization in the thread (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Reduction of hardness after retempering (ISO 898-1))	-	1000	-
4-Table 3(Mechanical property-Breaking torque (ISO 898-1))	-	5000	-
4-Table 3(Mechanical property-Impact strength (ISO 898-1))	-	3000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Quench Cracks(ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging cracks (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1)- Chamfer Circle)	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging Bursts-Circular head screws (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1) (Chamfer Circle))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screw (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear Bursts-Circular head screws (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Circular head screws (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Raw material seams and laps (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Voids (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Folds (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Tool marks (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1) (Impairs Usability))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Damages (ISO 6157-1))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-- Quench cracks (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks - (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3) Chamfer Circle)	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Hexagon head screw (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Forging bursts-Circular head screws (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Width (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws-Depth (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)--Shear bursts-Hexagon head screws (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Circular head screws - (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Forging cracks in socket head screws- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Raw material, seams and laps- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Voids- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Folds- (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Tool marks - (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Laps on the thread - (ISO 6157-3))	-	1000	-
4-Table 3(Mechanical property-Surface integrity (ISO 898-1)-Damages - (ISO 6157-3))	-	1000	-

12 Jan, 2028

-
Included w.e.f 31.12.2025

122

IS 1363 : Part 2 (2023)

Hexagon head bolts, screws and nuts of product grade C Part 2 Hexagon head screws (Size range M5 to M64) (sixth revision)

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Dimensions)	-	1000	-
5- Table 4 -(i)(General requirements)	-	1000	-
5- Table 4 -(ii)(Thread)	-	5000	-
5- Table 4 -(iii)(Mechanical properties)	-	12000	-
5- Table 4 -(iv)(Tolerances)	-	1000	-
5- Table 4 -(v)(Surface condition)	-	3000	-
5- Table 4 -(vi)(Surface integrity)	-	3000	-
5- Table 4 -(vii)(Acceptability)	-	1000	-
6(Marking and labelling)	-	1000	-
7(Designation)	-	1000	-
4(Finish -Electrolite zinc coating)	-	3000	-

12 Jan, 2028

-
Included w.e.f 02.07.2025

123

IS 1363 : Part 1 (2023)

Hexagon head bolts, screws and nuts of product grade C Part 1 Hexagon head bolts (Size range M5 to M64) (sixth revision)

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Dimensions)	-	1000	-
Cl-5, Table-5(General requirements)	-	1000	-
Cl-5, Table-5(Thread-Tolerance class)	-	3000	-
Cl-5, Table-5(Mechanical properties- Property class, Symbol)	-	12000	-
Cl-5, Table-5(Surface condition -Electroplated coatings)	-	5000	-
Cl-5, Table-5(Surface condition- Non-electrolytically applied zinc flake)	-	5000	-
Cl-5, Table-5(Surface condition - Hot dip galvanized coatings)	-	5000	-
Cl-5, Table-5(Surface integrity- Limits for surface discontinuities)	-	5000	-
Cl-6(Marking)	-	1000	-
Cl-5, Table-5(Tolerances-Product grade)	-	1000	-

12 Jan, 2028

-
Included w.e.f 02.07.2025

124

IS 2202 : Part 1 (2023)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 1 PLYWOOD FACE PANELS Seventh Revision

9990 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(Workmanship & Finish)	-	100	-
9.2(Workmanship & Finish)	-	100	-
9.3(Workmanship & Finish)	-	100	-
11.1(Dimensions - Height)	-	200	-
11.1(Dimensions - Width)	-	200	-
11.1(Dimensions - Thickness)	-	200	-
11.1(Dimensions - Variation in thickness)	-	200	-
11.1(Dimensions - Squareness)	-	200	-
11.12(End immersion test)	-	500	-
11.13(Knife Test)	-	500	-
11.14(Glue Adhesion Test)	-	500	-
4(GRADE)	-	100	-
4(TYPE)	-	100	-
5(SIZES)	-	100	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	100	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	100	-
7.1.2(CONSTRUCTION-Blockboard Core)	-	100	-
7.3.2(CONSTRUCTION-Stiles and Rails)	-	100	-
7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints)	-	100	-
7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints)	-	100	-
7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints)	-	100	-
7.3.3(CONSTRUCTION-Stiles and Rails)	-	100	-
9.1(WORKMANSHIP AND FINISH)	-	100	-
9.2(WORKMANSHIP AND FINISH)	-	100	-
9.3(WORKMANSHIP AND FINISH)	-	100	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.1(Dimensions and Squareness Test)	-	200	-
11.2(General Flatness Test)	-	500	-
11.2(General Flatness Test)	-	500	-
11.2(General Flatness Test)	-	500	-
11.3(Local Planeness Test)	-	500	-
11.4(Impact Indentation Test)	-	500	-
11.4(Impact Indentation Test)	-	500	-
11.5(Flexure Test)	-	500	-
11.5(Flexure Test)	-	500	-
11.6(Edge Loading Test)	-	500	-
11.6(Edge Loading Test)	-	500	-
11.6(Edge Loading Test)	-	500	-
11.6(Edge Loading Test)	-	500	-
11.7.1(Shock Resistance Test)	-	500	-
11.7.2(Shock Resistance Test)	-	500	-
11.8(Buckling Test)	-	500	-
11.8(Buckling Test)	-	500	-
11.8(Buckling Test)	-	500	-
11.9.2(Slamming Test)	-	500	-
11.9.3(Slamming Test)	-	500	-
11.10(Misuse Test)	-	500	-
11.11(Varying Humidity Test)	-	500	-
11.11(Varying Humidity Test)	-	500	-
11.12(End Immersion Test)	-	500	-
11.13(Knife Test)	-	500	-
11.14(Glue Adhesion Test)	-	500	-
11.15(Screw Withdrawal Resistance Test)	-	500	-
11.15(Screw Withdrawal Resistance Test)	-	500	-
Clause 4.2(grades specified)	-	100	-
Clause 5(SIZES)	-	100	-
Clause 6.1.1(species of timber)	-	100	-
Clause 6.1.2(list of species)	-	100	-
Clause 6.1.3(moisture content)	-	500	-
Clause 6.2.1(Plywood)	-	100	-
Clause 6.2.2(Decorative plywood)	-	100	-
Clause 6.3(Cross-Bands)	-	100	-
Clause 6.4.1(Commercial Face Veneers)	-	100	-
Clause 6.4.2(Decorative Face Veneers)	-	100	-
Clause 6.6.1(Adhesives)	-	100	-
Clause 6.7(Particle Board)	-	100	-
Clause 6.8(Medium density fibre board)	-	100	-
Clause 6.9(Alternative Materials)	-	100	-
Clause 7.1(Blockboard Core)	-	100	-
Clause 7.2(Particle Board or Medium Density Fibre)	-	100	-
Clause 7.3(Stiles and Rails)	-	100	-
Clause 7.4(Levelling)	-	100	-
Clause 7.5(Face Panel)	-	100	-
Clause 7.6(Lipping)	-	100	-
Clause 7.7(Rebating)	-	100	-
Clause 7.8(Opening for Glazing)	-	100	-
Clause 7.9(Venetian)	-	100	-
Clause 8.1(Locks)	-	100	-
Clause 9(WORKMANSHIP AND FINISH)	-	100	-
Clause 10.1(Classification of Tests)	-	100	-
Clause 11.1(Dimensions and Squareness Test)	-	200	-
Clause 11.2(General Flatness Test)	-	200	-
Clause 11.3(Local Planeness Test)	-	200	-
Clause 11.4(Impact Indentation Test)	-	500	-
Clause 11.5(Flexure Test)	-	500	-
Clause 11.6(Edge Loading Test)	-	500	-
Clause 11.7(Shock Resistance Test)	-	500	-
Clause 11.8(Buckling Resistance Test)	-	500	-
Clause 11.9(Slamming Test)	-	500	-
Clause 11.10(Misuse Test)	-	500	-
Clause 11.11(Varying Humidity Test)	-	500	-
Clause 11.12(End Immersion Test)	-	500	-
Clause 11.13(Knife Test)	-	500	-
Clause 11.14(Glue Adhesion Test)	-	500	-
Clause 11.15(Screw Withdrawal Resistance Test)	-	500	-
Clause 12(SAMPLING AND CRITERIA FOR CONFORMITY)	-	100	-
Clause 13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	100	-
Clause 14(Marking)	-	100	-
4(Grade, Type and Construction)	-	100	-
5(Sizes and Thickness)	-	200	-
6.1(Timber)	-	100	-
6.2(Plywood for flush door shutter)	-	100	-
6.3(Cross-Bands )	-	100	-
6.4.1(Commercial Face Veneers)	-	100	-
6.4.2(Decorative face veneers)	-	100	-
6.6(Adhesives)	-	100	-
6.7(Particle Board)	-	100	-
6.8(Medium Density Fibre)	-	100	-
6.9(Alternative Materials)	-	100	-
7(Construction)	-	100	-
8.1(Locks)	-	100	-
8.2(Other Fittings)	-	100	-
9(Workmanship and Finish)	-	100	-
10(Tests)	-	100	-
11.1(Dimensions and Squareness Test)	-	200	-
11.2(General Flatness Test)	-	500	-
11.3(Local Planeness Test)	-	500	-
11.4(Impact Indentation Test)	-	500	-
11.5(Flexure Test)	-	500	-
11.6(Edge Loading Test)	-	500	-
11.7(Shock Resistance Test)	-	500	-
11.8(Buckling Resistance Test)	-	500	-
11.9(Slamming Test)	-	500	-
11.1(Misuse Test)	-	500	-
11.11(Varying Humidity Test)	-	500	-
11.12(End Immersion Test)	-	500	-
11.13(Knife Test)	-	500	-
11.14(Glue Adhesion Test)	-	500	-
11.15(Screw Withdrawal Resistance Test)	-	500	-
14(Marking )	-	100	-
Cl-13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	100	-
9.1(Workmanship & Finish)	-	-	-
9.2(Workmanship & Finish)	-	-	-
9.3(Workmanship & Finish)	-	-	-
11.1(Dimensions - Height)	-	-	-
11.1(Dimensions - Width)	-	-	-
11.1(Dimensions - Thickness)	-	-	-
11.1(Dimensions - Variation in thickness)	-	-	-
11.1(Dimensions - Squareness)	-	-	-
11.12(End immersion test)	-	-	-
11.13(Knife Test)	-	-	-
11.14(Glue Adhesion Test)	-	-	-
4(GRADE)	-	-	-
4(TYPE)	-	-	-
5(SIZES)	-	-	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	-	-
7.1.1(CONSTRUCTION-Blockboard Core)	-	-	-
7.1.2(CONSTRUCTION-Blockboard Core)	-	-	-
7.3.2(CONSTRUCTION-Stiles and Rails)	-	-	-
7.3.2(a)(CONSTRUCTION-Stiles and Rails-Joints)	-	-	-
7.3.2(b)(CONSTRUCTION-Stiles and Rails-Joints)	-	-	-
7.3.2(c)(CONSTRUCTION-Stiles and Rails-Joints)	-	-	-
7.3.3(CONSTRUCTION-Stiles and Rails)	-	-	-
9.1(WORKMANSHIP AND FINISH)	-	-	-
9.2(WORKMANSHIP AND FINISH)	-	-	-
9.3(WORKMANSHIP AND FINISH)	-	-	-
11.1(Dimensions and Squareness Test)	-	-	-
11.1(Dimensions and Squareness Test)	-	-	-
11.1(Dimensions and Squareness Test)	-	-	-
11.1(Dimensions and Squareness Test)	-	-	-
11.1(Dimensions and Squareness Test)	-	-	-
11.2(General Flatness Test)	-	-	-
11.2(General Flatness Test)	-	-	-
11.2(General Flatness Test)	-	-	-
11.3(Local Planeness Test)	-	-	-
11.4(Impact Indentation Test)	-	-	-
11.4(Impact Indentation Test)	-	-	-
11.5(Flexure Test)	-	-	-
11.5(Flexure Test)	-	-	-
11.6(Edge Loading Test)	-	-	-
11.6(Edge Loading Test)	-	-	-
11.6(Edge Loading Test)	-	-	-
11.6(Edge Loading Test)	-	-	-
11.7.1(Shock Resistance Test)	-	-	-
11.7.2(Shock Resistance Test)	-	-	-
11.8(Buckling Test)	-	-	-
11.8(Buckling Test)	-	-	-
11.8(Buckling Test)	-	-	-
11.9.2(Slamming Test)	-	-	-
11.9.3(Slamming Test)	-	-	-
11.10(Misuse Test)	-	-	-
11.11(Varying Humidity Test)	-	-	-
11.11(Varying Humidity Test)	-	-	-
11.12(End Immersion Test)	-	-	-
11.13(Knife Test)	-	-	-
11.14(Glue Adhesion Test)	-	-	-
11.15(Screw Withdrawal Resistance Test)	-	-	-
11.15(Screw Withdrawal Resistance Test)	-	-	-
Clause 4.2(grades specified)	-	-	-
Clause 5(SIZES)	-	-	-
Clause 6.1.1(species of timber)	-	-	-
Clause 6.1.2(list of species)	-	-	-
Clause 6.1.3(moisture content)	-	-	-
Clause 6.2.1(Plywood)	-	-	-
Clause 6.2.2(Decorative plywood)	-	-	-
Clause 6.3(Cross-Bands)	-	-	-
Clause 6.4.1(Commercial Face Veneers)	-	-	-
Clause 6.4.2(Decorative Face Veneers)	-	-	-
Clause 6.6.1(Adhesives)	-	-	-
Clause 6.7(Particle Board)	-	-	-
Clause 6.8(Medium density fibre board)	-	-	-
Clause 6.9(Alternative Materials)	-	-	-
Clause 7.1(Blockboard Core)	-	-	-
Clause 7.2(Particle Board or Medium Density Fibre)	-	-	-
Clause 7.3(Stiles and Rails)	-	-	-
Clause 7.4(Levelling)	-	-	-
Clause 7.5(Face Panel)	-	-	-
Clause 7.6(Lipping)	-	-	-
Clause 7.7(Rebating)	-	-	-
Clause 7.8(Opening for Glazing)	-	-	-
Clause 7.9(Venetian)	-	-	-
Clause 8.1(Locks)	-	-	-
Clause 9(WORKMANSHIP AND FINISH)	-	-	-
Clause 10.1(Classification of Tests)	-	-	-
Clause 11.1(Dimensions and Squareness Test)	-	-	-
Clause 11.2(General Flatness Test)	-	-	-
Clause 11.3(Local Planeness Test)	-	-	-
Clause 11.4(Impact Indentation Test)	-	-	-
Clause 11.5(Flexure Test)	-	-	-
Clause 11.6(Edge Loading Test)	-	-	-
Clause 11.7(Shock Resistance Test)	-	-	-
Clause 11.8(Buckling Resistance Test)	-	-	-
Clause 11.9(Slamming Test)	-	-	-
Clause 11.10(Misuse Test)	-	-	-
Clause 11.11(Varying Humidity Test)	-	-	-
Clause 11.12(End Immersion Test)	-	-	-
Clause 11.13(Knife Test)	-	-	-
Clause 11.14(Glue Adhesion Test)	-	-	-
Clause 11.15(Screw Withdrawal Resistance Test)	-	-	-
Clause 12(SAMPLING AND CRITERIA FOR CONFORMITY)	-	-	-
Clause 13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	-	-
Clause 14(Marking)	-	-	-
4(Grade, Type and Construction)	-	-	-
5(Sizes and Thickness)	-	-	-
6.1(Timber)	-	-	-
6.2(Plywood for flush door shutter)	-	-	-
6.3(Cross-Bands )	-	-	-
6.4.1(Commercial Face Veneers)	-	-	-
6.4.2(Decorative face veneers)	-	-	-
6.6(Adhesives)	-	-	-
6.7(Particle Board)	-	-	-
6.8(Medium Density Fibre)	-	-	-
6.9(Alternative Materials)	-	-	-
7(Construction)	-	-	-
8.1(Locks)	-	-	-
8.2(Other Fittings)	-	-	-
9(Workmanship and Finish)	-	-	-
10(Tests)	-	-	-
11.1(Dimensions and Squareness Test)	-	-	-
11.2(General Flatness Test)	-	-	-
11.3(Local Planeness Test)	-	-	-
11.4(Impact Indentation Test)	-	-	-
11.5(Flexure Test)	-	-	-
11.6(Edge Loading Test)	-	-	-
11.7(Shock Resistance Test)	-	-	-
11.8(Buckling Resistance Test)	-	-	-
11.9(Slamming Test)	-	-	-
11.1(Misuse Test)	-	-	-
11.11(Varying Humidity Test)	-	-	-
11.12(End Immersion Test)	-	-	-
11.13(Knife Test)	-	-	-
11.14(Glue Adhesion Test)	-	-	-
11.15(Screw Withdrawal Resistance Test)	-	-	-
14(Marking )	-	-	-
Cl-13(ADDITIONAL REQUIREMENTS FOR ECO MARK)	-	-	-

12 Jan, 2028

-
Included w.e.f.28.07.2025

125

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	1500	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	1000	-
11(Transverse Tension Test,%)	-	1000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	500	-
13 (Table No.- 7)(Flaring Test)	-	1000	-
14(Flattaning Test-IS 2328)	-	1000	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	1500	-
17(Leak Tighteness Test)	-	1500	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	2500	-
19(Eddy current test & Air under water)	-	1500	-
21(Workmanship, Finish and Appearance)	-	100	-
22(Repair by Welding or Grinding)	-	100	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	100	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	1500	-
Clause 10.1 - Table 4(Tensile Strength)	-	1500	-
Clause 10.1 - Table 4(Percent Elongation)	-	1500	-
Clause 11(Transverse Tension Test)	-	1500	-
Clause 12(Hardness Test)	-	1000	-
Clause 13(Flaring Test)	-	1000	-
Clause 14(Flattening Test)	-	1000	-
Clause 15(Grain Size)	-	1500	-
Clause 17(Leak Tightness Test)	-	1500	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	2500	-
Clause 21(Workmanship, Finish & Appearance)	-	100	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	100	-
10.2(Hardness test IS 1500 (part-1):2019)	-	500	-
12.2(Flaring test IS 17878:2022)	-	1000	-
16(Sampling)	-	100	-
24(Marking)	-	100	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	500	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	500	-

12 Jan, 2028

-
Included w.e.f.28.07.2025 Exclusion Excluding Eddy Current and Air Under Water

126

IS 17876 (2022)

Stainless steel welded pipes and tubes for general service

15500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	1500	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	1000	-
11(Transverse Tension Test,%)	-	1000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	500	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	1000	-
14(Reverse Flattaning Test)	-	1000	-
15(Flattaning Test-IS 2328)	-	1000	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	1500	-
18(Leak Tighteness Test)	-	1500	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	2500	-
20(Eddy current test, Air under water test ,Radiographic tests)	-	1500	-
22(Workmanship, Finish and Appearance)	-	100	-
23(Repair by Welding or Grinding)	-	100	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	100	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	500	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	500	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	2500	-
Clause 10.1 - Table 4(Tensile Strength)	-	1500	-
Clause 10.1 - Table 4(Yield Strength)	-	1500	-
Clause 10.1 - Table 4(Percent Elongation)	-	1500	-
Clause 11(Transverse Tension Test)	-	1500	-
Clause 12(Hardness Test)	-	1000	-
Clause 13(Flange Test)	-	1500	-
Clause 14(Reverse Flattening Test)	-	1500	-
Clause 15(Flattening Test)	-	1500	-
Clause 16(Grain Size)	-	1500	-
Clause 18()	-	1500	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	2500	-
Clause 22(Workmanship, Finish & Appearance)	-	200	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	200	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	500	-
8.1 & 8.2 (Table No.- 1)(Tungstun (W))	-	500	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	500	-
12.2(Hardness test)	-	1000	-
17(Sampling)	-	100	-
25(Marking)	-	100	-
6.7, Table 7, ii)(c) Chromium VI)	-	500	-

12 Jan, 2028

-
Included w.e.f 20.06.2025

127

IS 453 (1993)

Double Acting Spring Hinges -Specification

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(DIMENSIONS)	-	200	-
9(PERFORMANCE TESTS)	-	12000	-
Clause 4.1(Mild Steel Sheet)	-	1500	-
Clause 4.2(Mild Steel Wire)	-	1500	-
Clause 4.3(Cast Brass)	-	1500	-
Clause 4.4(Brass Sheets)	-	1500	-
Clause 4.5(Brass Rods)	-	1500	-
Clause 4.6(Steel Wire)	-	1500	-
Clause 4.7(Phosphor Bronze Wire)	-	1500	-
Clause 5(Sizes)	-	200	-
Clause 6(Dimensions)	-	200	-
Clause 8(Finish)	-	200	-
Clause 9(Performance Test)	-	12000	-
Clause 10(Marking)	-	200	-
Clause 11(Packing)	-	200	-
Cl-7.1(Mild Steel Hinges)	-	1500	-
Cl-7.1.1(Blank hinge shall be made from mild steel sheet)	-	1500	-
Cl-7.2(Brass Hinges)	-	1500	-
Cl-7.2.1(Blank hinges shall be made of cast brass)	-	1500	-
Clause-9.0(Performance Test)	-	12000	-

12 Jan, 2028

-
Included w.e.f 20.06.2025

128

IS 3843 (1995)

Steel back flap hinges -Specification

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 6, Table 1, Table 2(Dimensions)	-	1000	-
Clause 4 Table 3(i)(Flap)	-	3000	-
Clause 4 Table 3(ii)(Pin)	-	3000	-
Clause 5(Dimension and tolerance)	-	1000	-
Clause 8(Marking)	-	1000	-
Clause 9(Packing)	-	1000	-
5, 6, Table 1, Table 2(Dimensions)	-	1000	-
Clause 4 Table 3(i)(Flap)	-	3000	-
Clause 4 Table 3(ii)(Pin)	-	3000	-
Clause 5(Dimension and tolerance)	-	1000	-
Clause 8(Marking)	-	1000	-
Clause 9(Packing)	-	1000	-

12 Jan, 2028

-
Included w.e.f.27.06.2025

129

IS 3818 (1992)

Continuous (Piano) hinges -Specification

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6 (Ref. Cl.9 of IS 1868:1996)(Anodic casting thickness (Cl. 9.2 of IS 1868:1996))	-	2000	-
4-Fig 1(DIMENSIONS AND TOLERANCES-Nominal Size)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-B)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-C)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-D)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-T)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES-minimum distance of screw holes from the end of flap)	-	200	-
4-Fig 1(DIMENSIONS AND TOLERANCES- Other Dimensions)	-	200	-
4-Fig 2(DIMENSIONS AND TOLERANCES-CoNTINUOUS ( PIANO) HINGIS TYPB III; 50 min NOMINAL SID)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B1)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-B2)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-C)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-D)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-T)	-	200	-
4-Fig 3(DIMENSIONS AND TOLERANCES-CSK Screw No.)	-	200	-
5.1(MANUFACTURE)	-	200	-
5.2(MANUFACTURE-Knuekles)	-	200	-
5.2(MANUFACTURE-Knuekles)	-	200	-
5.3(MANUFACTURE-Pins)	-	200	-
5.3(MANUFACTURE-Pins)	-	200	-
5.3(MANUFACTURE-Pin-Anodized thickness)	-	1500	-
5.3(MANUFACTURE-Pins)	-	200	-
5.4(MANUFACTURE-Screw Holes)	-	200	-
6(Finish)	-	200	-

12 Jan, 2028

-
Included w.e.f.25.06.2025

130

IS 362 (1991)

Parliament Hinges -specification

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 (Brass parliament hinges shall have either bright or satin finish and shall be suitably protected against discoloration)	-	3500	-
Cl. 7.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance)	-	3500	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright, natural, sat or satin finish or dyed. )	-	3500	-
Cl. 7.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	3500	-
Cl. 7.3(Mild steel parliament hinges shall be finished bright or electro-galvanized as specified by the purchaser)	-	3500	-
3(Type)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Size)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-No. of Screw holes)	-	200	-
5.1-able 2(Dlmenslons for Aluminium Alloy Parliament Hinges-Holes for screw designation)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Size)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-A)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-B)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-C)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-D)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-d)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-E)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-No. of Screw holes)	-	200	-
5.1-able 3(Dimensions for Cast Brass Parliament Hinges-Holes for screw designation)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Size)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-A)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-B)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-C)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-D)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-d)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-E)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-No. of Screw holes)	-	200	-
5.1-Table 4(Dimensions for Mild Steel Parliament Hinges-Holes for screw designation)	-	200	-
6.1(MANUFACTURE-General)	-	200	-
6.1(MANUFACTURE-General)	-	200	-
6.1(MANUFACTURE-General)	-	200	-
6.2(MANUFACTURE-Knuckles)	-	200	-
6.2(MANUFACTURE-Knuckles)	-	200	-
6.2(MANUFACTURE-Knuckles)	-	200	-
6.2(MANUFACTURE-Knuckles)	-	200	-
6.3(MANUFACTURE-Pins)	-	200	-
6.3(MANUFACTURE-Pins)	-	200	-
6.3(MANUFACTURE-Pins)	-	200	-
6.3(MANUFACTURE-Pins)	-	200	-
6.4(MANUFACTURE-Screw Holes)	-	200	-
6.5(MANUFACTURE-Position of Holes)	-	500	-
6.5(MANUFACTURE-Position of Holes)	-	500	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the ends of the flap)	-	500	-
6.5(MANUFACTURE-Position of Holes-minimum distance from the inner edge)	-	500	-
6.5(MANUFACTURE-Position of Holes)	-	500	-
7.1(FINISH)	-	500	-
7.3(FINISH)	-	500	-

12 Jan, 2028

-
Included w.e.f.26.06.2025

131

IS 206 (2010)

Tee and strap hinges - Specification (Fifth Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(DIMENSIONS AND TOLERANCES)	-	500	-
6(WORKMANSHIP)	-	500	-
7(FINISH)	-	500	-
10(MARKING)	-	500	-
Clause 3.1,1(Light weight (Type 1))	-	500	-
Clause 3.1,2(Light weight (Type 2))	-	500	-
Clause 3.1,3(Medium weight (Type 1))	-	500	-
Clause 3.1,4(Medium weight (Type 2))	-	500	-
Clause 3.1,5(Heavy weight (Type 1))	-	500	-
Clause 3.1,6(Heavy weight (Type 2))	-	500	-
Clause 3.1,7(Heavy weight (Type 3))	-	500	-
Clause 3.2,1(Light weight)	-	500	-
Clause 3.2,2(Medium weight (Type 1))	-	500	-
Clause 3.2,3(Medium weight (Type 2))	-	500	-
Clause 3.2,4(Heavy weight )	-	500	-
Clause 4 Table 1(i)(Mild steel sheet)	-	1500	-
Clause 4 Table 1(ii)(Mild steel wire)	-	1500	-
Clause 5.1(Dimensions)	-	500	-
Clause 6(Workmanship)	-	200	-
Clause 8(Packing)	-	200	-
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	200	-
Clause 10(Marking)	-	200	-
5(DIMENSIONS AND TOLERANCES)	-	-	-
6(WORKMANSHIP)	-	-	-
7(FINISH)	-	-	-
10(MARKING)	-	-	-
Clause 3.1,1(Light weight (Type 1))	-	-	-
Clause 3.1,2(Light weight (Type 2))	-	-	-
Clause 3.1,3(Medium weight (Type 1))	-	-	-
Clause 3.1,4(Medium weight (Type 2))	-	-	-
Clause 3.1,5(Heavy weight (Type 1))	-	-	-
Clause 3.1,6(Heavy weight (Type 2))	-	-	-
Clause 3.1,7(Heavy weight (Type 3))	-	-	-
Clause 3.2,1(Light weight)	-	-	-
Clause 3.2,2(Medium weight (Type 1))	-	-	-
Clause 3.2,3(Medium weight (Type 2))	-	-	-
Clause 3.2,4(Heavy weight )	-	-	-
Clause 4 Table 1(i)(Mild steel sheet)	-	-	-
Clause 4 Table 1(ii)(Mild steel wire)	-	-	-
Clause 5.1(Dimensions)	-	-	-
Clause 6(Workmanship)	-	-	-
Clause 8(Packing)	-	-	-
Clause 9(SAMPLING AND CRITERION FOR CONFORMITY)	-	-	-
Clause 10(Marking)	-	-	-

12 Jan, 2028

-
Included w.e.f.26.06.2025

132

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	500	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	500	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	500	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	500	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	500	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	500	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	500	-
4.1 -Table 1-Flap- i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	500	-
4.1 -Table 1- Flap-i (Ref. Cl 5.1, Table 1 Designation 64430 or 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	500	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Copper - IS 3685:1966)	-	500	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Lead - IS 3685:1966)	-	500	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Iron - IS 3685:1966)	-	500	-
4 -Table 1-Flap- ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	500	-
4 -Table 1- Flap-ii (Ref. Cl 8.1, Table 1 of IS 319 : 1989)(Chemical composition - Zinc- IS 3685:1966)	-	500	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	500	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	500	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	500	-
4 -Table 1-Flap- iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	500	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	500	-
4 -Table 1- Flap-iii (Ref. Cl 3.1, Table 1 Grade LCB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	500	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	500	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	500	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	500	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	500	-
4 -Table 1- Flap-iv (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	500	-
4.1 -Table 1-Pin- i (Ref. Cl 5.1, Table 1 Designation 64430 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	500	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Tin - IS 4027:1967)	-	500	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Phosphorous - IS 4027:1967)	-	500	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Lead - IS 4027:1967)	-	500	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Total impurities - IS 4027:1967)	-	500	-
4.1 -Table 1-Pin- ii (Ref. Cl 6.1, Table 1 of IS 7608 : 1987)(Chemical composition - Copper - IS 4027:1967)	-	500	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Carbon - IS 228)	-	500	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Manganese - IS 228)	-	500	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Sulphur - IS 228)	-	500	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 of IS 7887 : 1992)(Chemical composition - Phosphorous - IS 228)	-	500	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Silicon - IS 228 (optional))	-	500	-
4.1 -Table 1-Pin- iii (Ref. Cl 6 of IS 280:1978- Cross ref. Cl. 6.1 -Table 1 Note 2 of IS 7887 : 1992)(Chemical composition - Tota Aluminium - IS 228 (optional))	-	500	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Copper - IS 3685:1966)	-	500	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Lead - IS 3685:1966)	-	500	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Iron - IS 3685:1966)	-	500	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Total impurities - IS 3685:1966)	-	500	-
4.1 -Table 1-Pin- iv (Ref. Cl 4.1 -Table 1 of IS 4413 : 1981)(Chemical composition - Zinc - IS 3685:1966)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Carbon - IS 228)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Silicon - IS 228)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Manganese - IS 228)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Nickel - IS 228)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Chromium - IS 228)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Molybdenum - IS 228)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Sulphur - IS 228)	-	500	-
4.1 -Table 1-Pin- v (Ref. Cl 7.1 -Table 1 of IS 6528 : 1995)(Chemical composition - Phosphorous - IS 228)	-	500	-
3(TYPES)	-	100	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	100	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-	100	-
5.2 ,Table 6(Tolerances-Tolerances on dimensions of hinges )	-	100	-
6.1(Manufacture- General)	-	100	-
6.2- Table 2,3,4,5 (Kunckles)	-	100	-
6.3(Screw Holes)	-	100	-
6.3.1- Table 2,3,4,5 & Fig-1 & 2(Screw Holes)	-	100	-
6.3.2- Table 2,3,4,5 (Number of Holes)	-	100	-
6.3.3 Fig-1(Position of Holes)	-	100	-
8.1(Packing - Each hinge shall be packed in card board boxes or in any other approved packing. The number of hinges in a package shall be as under)	-	100	-
8.2(Packing -Each Package shall bear the following Particulars)	-	100	-
7(Workmanship & Finish)	-	100	-
10(Marking)	-	100	-

12 Jan, 2028

-
Included w.e.f.28.07.2025

133

IS 1341 (2018)

Steel Butt Hinges - Specification (Sixth Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 Tables 2 to 9(Types)	-	100	-
5.1 Tables 2 to 9 (2)(Size of Hinge)	-	100	-
5.1 Tables 2 to 9 (3)(Length A)	-	100	-
5.1 Tables 2 to 9 (4)(Breadth B)	-	100	-
5.1 Tables 2 to 9 (4)(Breadth B1)	-	100	-
5.1 Tables 2 to 9 (4)(Breadth B2)	-	100	-
5.1 Tables 2 to 9 (5)(Thickness of Flap C)	-	100	-
5.1 Tables 2 to 9 (6)(Diameter of Hinge Pin D)	-	100	-
5.1 Tables 2 to 9 (7)(Number of Knuckles)	-	100	-
5.1 Tables 2 to 9 (8)(Number of Screw Holes)	-	100	-
5.1 Tables 2 to 9 (9)(Holes for Screw No.)	-	100	-
6.1(General)	-	500	-
6.1(General)	-	500	-
6.1(General)	-	500	-
6.2.1(Knuckles)	-	100	-
6.3(Pins)	-	100	-
6.4(Screw Holes)	-	100	-
6.4.2(Position of Holes)	-	100	-
6.4.2(X)	-	100	-
6.4.2(Y)	-	100	-
6.4.2(Z)	-	100	-
6.4.2.1(Position of Holes)	-	100	-
7(Finish)	-	100	-
TABLE-1 (Clause-4)(TITANIUM)	-	500	-
TABLE-1 (Clause-4)(VANADIUM)	-	500	-
TABLE-1 (Clause-4)(NIOBIUM)	-	500	-
TABLE-1 (Clause-4)(Molybdenum)	-	500	-
TABLE-1 (Clause-4)(Chromium)	-	500	-
TABLE-1 (Clause-4)(Nickel)	-	500	-
TABLE-1 (Clause-4)( ALUMINIUM)	-	500	-
TABLE-1 (Clause-4)(SILICON)	-	500	-
TABLE-1 (Clause-4)(NITROGEN)	-	500	-
TABLE-1 (Clause-4)(MANGANESE)	-	500	-
TABLE-1 (Clause-4)(PHOSPHURS)	-	500	-
TABLE-1 (Clause-4)(SULPHUR)	-	500	-
TABLE-1 (Clause-4)( CARBON)	-	500	-
Clause 4 Table 1(Manganese ( Pin))	-	500	-
Clause 4 Table 1(Phosphorus ( Pin))	-	500	-
Clause 4 Table 1(Sulphur ( Pin))	-	500	-
Clause 4 Table 1(Carbon ( Pin))	-	500	-
Clause 4 Table 1(Nitrogen ( Flap))	-	500	-
Clause 4 Table 1(Manganese ( Flap))	-	500	-
Clause 4 Table 1(Phosphorus ( Flap))	-	500	-
Clause 4 Table 1(Sulphur ( Flap))	-	500	-
Clause 4 Table 1(Carbon ( Flap))	-	500	-
8(Marking)	-	100	-
Cl 4 & Table 1(Sulphur- IS 228(Part 9))	-	500	-
Cl 4 & Table 1(Carbon- IS 228(Part 1))	-	500	-
Cl 4 & Table 1(Phosphorous- IS 228(Part 3))	-	500	-
Cl 4 & Table 1(Manganese- IS 228(Part 2))	-	500	-
Cl 4 & Table 1(Silicon- IS 228(Part 2))	-	500	-
Cl 4 & Table 1(Nitrogen -IS 228(Part 19))	-	500	-

12 Jan, 2028

-
Included w.e.f.28.07.2025

134

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

18800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9.4(Load In Other Direction From Bend)	-	1500	-
Cl 9.3(Load In One Direction)	-	1500	-
Cl 8.1(UTM)	-	1500	-
Cl 7.2(Weight)	-	100	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 5(Deformations and Surface Characteristics)	-	100	-
Cl 9.4(Load In Other Direction From Bend)	-	1500	-
Cl 9.3(Load In One Direction)	-	1500	-
Cl 8.1(UTM)	-	1500	-
Cl 7.2(Weight)	-	100	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 5(Deformations and Surface Characteristics)	-	100	-
Cl 9.4(Load In Other Direction From Bend)	-	1500	-
Cl 9.3(Load In One Direction)	-	1500	-
Cl 8.1(UTM)	-	1500	-
Cl 7.2(Weight)	-	100	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 5(Deformations and Surface Characteristics)	-	100	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	200	-
4.1(Sulphur and phosphorous)	-	200	-
4.1(CE)	-	200	-
4.1( Nitrogen%)	-	200	-
4.1(Ni)	-	200	-
4.1(Mo)	-	200	-
4.1(Cr)	-	200	-
4.1( Ti)	-	200	-
4.1(V)	-	200	-
4.1( Nb)	-	200	-
4.1( Aluminium %)	-	200	-
4.1( Copper %)	-	200	-
4.1(Silicon %)	-	200	-
4.1(Sulphur %)	-	200	-
4.1(Phosphorus %)	-	200	-
4.1(Manganese %)	-	200	-
4.1(Carbon %)	-	200	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	500	-
Cl. 9.3, Table 4(Bend Test )	-	500	-
Cl. 8.1 Table 3(Elongation, percentage)	-	500	-
Cl. 8.1 Table 3(TS/YS ratio)	-	500	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	500	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	500	-
Cl. 7.2 Table -2 (Nominal Mass)	-	100	-
Cl. 6.1(Nominal Size)	-	100	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	100	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-	100	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR+PHOSPHUR)	-	200	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 MANGANESE)	-	200	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 NITROGEN)	-	200	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 PHOSPHURS)	-	200	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 SULPHUR)	-	200	-
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON )	-	200	-
Cl.4.2 of IS 1786 (Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl.4.2 of IS 1786 (Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl.4.2 of IS 1786 (Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl.4.2 of IS 1786 (Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl.4.2 of IS 1786 (Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl.4.2 of IS 1786 (Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl.4.2 of IS 1786 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl.4.2 of IS 1786 (Grade:- Fe 415D,Fe 415S, Fe 500D,Fe 500S,Fe 550D)(Carbon Equivalent)	-	200	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur & Phosphorous)	-	200	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Phosphorous- IS 228)	-	200	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Sulphur-IS 228)	-	200	-
Cl.4.2 of IS 1786 (Grade:- Fe 415,Fe 415D,Fe 415S,Fe 500,Fe 500D,Fe 500S,Fe 550,Fe 550D,Fe600,Fe 650,Fe 700)(Carbon-IS 228)	-	200	-
8.18.1 Table 3(Total elongation at maximum force)	-	500	-
Cl 5(Deformations and Surface Characteristics)	-	100	-
5.7(PullOut (Bond Test))	-	3500	-
4.2(Niobium (Nb))	-	200	-
4.2(Boron (B))	-	200	-
Cl. 5.7(Average compressive strength of cubes at 28 days)	-	2100	-
Cl. 5.7(Bond Strength at 0.25 mm slip)	-	2100	-
Cl. 5.7(Date of testing of concrete cubes)	-	100	-
Cl. 5.7(Date of casting of concrete cubes)	-	100	-
Cl. 8.1 Table 3(TS/YS Ratio)	-	500	-
Cl. 5.3 (b)(The ribs contributing the projected area - Transverse Ribs)	-	100	-
Cl. 5.3 (a)(The ribs contributing the projected area - Longitudinal Ribs)	-	100	-
Cl. 8.1 Table 3(Maximum Extension)	-	500	-
Cl. 8.1 Table 3(Total Elongation at Maximum Force)	-	500	-
Cl. 6.2, 6.3 Table 1(Gross Cross Sectional Area, A)	-	100	-
Cl. 4.3(Visual Inspection.)	-	100	-
Cl. 5.2(Surface Characteristics)	-	100	-
Clause 9.4(Rebend Test)	-	500	-
Clause 6.3(Effective Cross-sectional Area)	-	100	-
Clause 8.1(Table 3)(Total Elongation at Maximum Force)	-	100	-
Cl 9.4(Load In Other Direction From Bend)	-	1500	-
Cl 9.3(Load In One Direction)	-	1500	-
Cl 8.1(UTM)	-	1500	-
Cl 7.2(Weight)	-	100	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 5(Deformations and Surface Characteristics)	-	100	-
Cl 5(Deformations and Surface Characteristics)	-	100	-
Cl 6.1(Length, Width & Thickness)	-	100	-
Cl 7.2(Weight)	-	100	-
Cl 8.1(UTM)	-	1500	-
Cl 9.3(Load In One Direction)	-	1500	-
Cl 9.4(Load In Other Direction From Bend)	-	1500	-
13(Identification and marking)	-	100	-
5.7(Pull-out test - IS:2770(P1))	-	2100	-
7.0 & 7.1(Specified lengths - SOP MT-23)	-	100	-
8.0 & 8.1("Total elongation at maximum force on 5.65 vSo mm GL. ")	-	500	-
4.3(Rolling and cold working of bars/wire)	-	100	-
7.1(Specified length)	-	100	-
9.1(Preparation of test sample)	-	100	-
9.2(Tensile test,IS:1608(Pt1)-2018)	-	1500	-
9.5(Retest)	-	100	-
12(Inspection)	-	100	-
Clause 4.2 Note 2, Amendment 1 & 3(Nb+V+B+Ti)	-	200	-
Clause 4.2 Note 3, Amendment 1 & 3(Cr+Cu+Ni+Mo+P)	-	200	-
Clause 4.2, Amendment 3 Note 4("In order to ascertain whether sufficient quantities of nitrogen binding elements are present, following formula may be used, where all elements are in ppm. (N−120)< (Al free/10)+((Ti+V)/7)+(Nb/14)")	-	200	-
1()	-	0	-

12 Jan, 2028

-
-

135

IS 1030 (1998)

Carbon steel castings for general engineering purposes - Specification (Fifth Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CI.8.1, 8.3 and 8.4.1, Table-1(Carbon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Sulpur)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Phosphorus)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1()	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Silicon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Chromium)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Nickel)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Molybdenum)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Copper)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Vanadium)	-	1500	-
CI.13.2, Table-2(Tensile Test)	-	1500	-
CI.13.2, Table-2(Yield Stress)	-	1500	-
CI.13.2, Table-2(Elongation)	-	1500	-
CI.13.4, Table-2(Bend Test)	-	1000	-
CI.13.3(Impact Test)	-	2500	-
CI.13.3(Hydraulic Test)	-	1500	-
9(Workmanship & Finish)	-	100	-
10(Freedom from defects)	-	100	-
11(Fetting and dressing)	-	100	-
14(Non-destructive tests)	-	1500	-
16(Hydraulic test)	-	1500	-
18(Marking)	-	100	-
1()	-	1000	-
CI.8.1, 8.3 and 8.4.1, Table-1(Carbon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Sulpur)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Phosphorus)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1()	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Silicon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Chromium)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Nickel)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Molybdenum)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Copper)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Vanadium)	-	1500	-
CI.13.2, Table-2(Tensile Test)	-	1500	-
CI.13.2, Table-2(Yield Stress)	-	1500	-
CI.13.2, Table-2(Elongation)	-	1500	-
CI.13.4, Table-2(Bend Test)	-	1000	-
CI.13.3(Impact Test)	-	2500	-
CI.13.3(Hydraulic Test)	-	1500	-
9(Workmanship & Finish)	-	100	-
10(Freedom from defects)	-	100	-
11(Fetting and dressing)	-	100	-
14(Non-destructive tests)	-	1500	-
16(Hydraulic test)	-	1500	-
18(Marking)	-	100	-
1()	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Carbon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Sulpur)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Phosphorus)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1()	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Silicon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Chromium)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Nickel)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Molybdenum)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Copper)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Vanadium)	-	1500	-
CI.13.2, Table-2(Tensile Test)	-	1500	-
CI.13.2, Table-2(Yield Stress)	-	1500	-
CI.13.2, Table-2(Elongation)	-	1500	-
CI.13.4, Table-2(Bend Test)	-	1000	-
CI.13.3(Impact Test)	-	2500	-
CI.13.3(Hydraulic Test)	-	1500	-
9(Workmanship & Finish)	-	100	-
10(Freedom from defects)	-	100	-
11(Fetting and dressing)	-	100	-
14(Non-destructive tests)	-	1500	-
16(Hydraulic test)	-	1500	-
18(Marking)	-	1000	-
1()	-	1000	-
CI.8.1, 8.3 and 8.4.1, Table-1(Carbon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Sulpur)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Phosphorus)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1()	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Silicon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Chromium)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Nickel)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Molybdenum)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Copper)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Vanadium)	-	1500	-
CI.13.2, Table-2(Tensile Test)	-	1500	-
CI.13.2, Table-2(Yield Stress)	-	1500	-
CI.13.2, Table-2(Elongation)	-	1500	-
CI.13.4, Table-2(Bend Test)	-	1000	-
CI.13.3(Impact Test)	-	2500	-
CI.13.3(Hydraulic Test)	-	1500	-
9(Workmanship & Finish)	-	100	-
10(Freedom from defects)	-	100	-
11(Fetting and dressing)	-	100	-
14(Non-destructive tests)	-	1500	-
16(Hydraulic test)	-	1500	-
18(Marking)	-	100	-
1()	-	1000	-
CI.8.1, 8.3 and 8.4.1, Table-1(Carbon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Sulpur)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Phosphorus)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1()	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Silicon)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Chromium)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Nickel)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Molybdenum)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Copper)	-	1500	-
CI.8.1, 8.3 and 8.4.1, Table-1(Vanadium)	-	1500	-
CI.13.2, Table-2(Tensile Test)	-	1500	-
CI.13.2, Table-2(Yield Stress)	-	1500	-
CI.13.2, Table-2(Elongation)	-	1500	-
CI.13.4, Table-2(Bend Test)	-	1000	-
CI.13.3(Impact Test)	-	2500	-
CI.13.3(Hydraulic Test)	-	1500	-
9(Workmanship & Finish)	-	100	-
10(Freedom from defects)	-	100	-
11(Fetting and dressing)	-	100	-
14(Non-destructive tests)	-	1500	-
16(Hydraulic test)	-	1500	-
18(Marking)	-	100	-
1()	-	1000	-

12 Jan, 2028

-
Included w.e.f.18.06.2025

136

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

8090 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
6.1, 6.2(cr + n + mo)	-	1500	-
6.1, 6.2(tin)	-	500	-
6.1, 6.2(boron)	-	500	-
6.1, 6.2(vanadium)	-	500	-
6.1, 6.2(molybdenum)	-	500	-
6.1, 6.2(copper)	-	500	-
6.1, 6.2(cromium)	-	500	-
6.1, 6.2(nickel)	-	500	-
6.1, 6.2(aluminium)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6.1, 6.2(phosphorus)	-	500	-
6.1, 6.2(sulphur)	-	500	-
6.1, 6.2(manganese)	-	500	-
6.1, 6.2(silicon )	-	500	-
6.1, 6.2(carbon)	-	500	-
6, table 1(Chemical Composition)	-	8000	-
7(Freedom from defects)	-	500	-
8(Dimensional Properties (Diameter))	-	500	-
8(Dimensional Properties (Ovality))	-	500	-
8(Dimensional Properties (Weight per Meter, kg))	-	500	-
9.1, table 2(Tensile Strength)	-	1500	-
9.1, table 2(Yield Strength)	-	1500	-
9.1, table 2(Elongation)	-	1500	-
9.2, table 2(hardness test)	-	1000	-
12.2(Bend Test)	-	1000	-
12.3(grain size)	-	1800	-
12.4(Macrostructure)	-	1800	-
12.5(Ultrasonic Test)	-	1800	-
12.6(Magnetic Particle Test)	-	1800	-
12.7(Blue Fracture Test)	-	1800	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	1500	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	1000	-
9.1(Tensile Strength - IS: 1608(P1))	-	1500	-
9.1(Yield Strength-IS:1608(P1))	-	1500	-
9.1(Elongation on SoA 5.65mm GL)	-	1500	-
9.2(Hardness-HB IS:1500 (P1))	-	1000	-
12.0 & 12.2(Bend Test - IS 1599)	-	1000	-
12.0 & 12.3(Grain Size - IS 4748)	-	1800	-
12.0 & 12.4(Macrostructure- IS 11371)	-	1800	-
12.0 & 12.5(Ultrasnoic Test)	-	1800	-
12.0 & 12.6(Magnetic Particle Test - IS 10138 (P3))	-	1800	-
5(Manufacture)	-	100	-
7(Freedom from defects)	-	100	-
13(Marking)	-	100	-
12.7(Blue fracture test (IS:1875-1985))	-	1800	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	1500	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	1000	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
6, table 1(Chemical Composition)	-	1500	-
7(Freedom from defects)	-	100	-
8(Dimensional Properties (Diameter))	-	500	-
8(Dimensional Properties (Ovality))	-	500	-
8(Dimensional Properties (Weight per Meter, kg))	-	500	-
9.1, table 2(Tensile Strength)	-	1500	-
9.1, table 2(Yield Strength)	-	1500	-
9.1, table 2(Elongation)	-	1500	-
9.2, table 2(hardness test)	-	1000	-
12.2(Bend Test)	-	1000	-
12.3(grain size)	-	1800	-
12.4(Macrostructure)	-	1800	-
12.5(Ultrasonic Test)	-	1800	-
12.6(Magnetic Particle Test)	-	1800	-
12.7(Blue Fracture Test)	-	1800	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	500	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	1500	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	1500	-
9.1(Tensile Strength - IS: 1608(P1))	-	1500	-
9.1(Yield Strength-IS:1608(P1))	-	1500	-
9.1(Elongation on SoA 5.65mm GL)	-	1500	-
9.2(Hardness-HB IS:1500 (P1))	-	1000	-
12.0 & 12.2(Bend Test - IS 1599)	-	1000	-
12.0 & 12.3(Grain Size - IS 4748)	-	1800	-
12.0 & 12.4(Macrostructure- IS 11371)	-	1800	-
12.0 & 12.5(Ultrasnoic Test)	-	1800	-
12.0 & 12.6(Magnetic Particle Test - IS 10138 (P3))	-	1800	-
5(Manufacture)	-	100	-
7(Freedom from defects)	-	100	-
13(Marking)	-	100	-
12.7(Blue fracture test (IS:1875-1985))	-	1800	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	1500	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	1500	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
6, table 1(Chemical Composition)	-	8000	-
7(Freedom from defects)	-	500	-
8(Dimensional Properties (Diameter))	-	500	-
8(Dimensional Properties (Ovality))	-	500	-
8(Dimensional Properties (Weight per Meter, kg))	-	500	-
9.1, table 2(Tensile Strength)	-	1500	-
9.1, table 2(Yield Strength)	-	1500	-
9.1, table 2(Elongation)	-	1500	-
9.2, table 2(hardness test)	-	1000	-
12.2(Bend Test)	-	1000	-
12.3(grain size)	-	1800	-
12.4(Macrostructure)	-	1800	-
12.5(Ultrasonic Test)	-	1800	-
12.6(Magnetic Particle Test)	-	1800	-
12.7(Blue Fracture Test)	-	1800	-
Cl 12(Supplementary Requirements)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 7(Workmanship)	-	100	-
Cl 8(Diameter, Ovality & Weight)	-	100	-
Cl 9(UTM & HBW)	-	2500	-
Cl 12(Supplementary Requirements)	-	100	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	1500	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	1000	-
9.1(Tensile Strength - IS: 1608(P1))	-	1500	-
9.1(Yield Strength-IS:1608(P1))	-	1500	-
9.1(Elongation on SoA 5.65mm GL)	-	1500	-
9.2(Hardness-HB IS:1500 (P1))	-	1000	-
12.0 & 12.2(Bend Test - IS 1599)	-	1000	-
12.0 & 12.3(Grain Size - IS 4748)	-	1800	-
12.0 & 12.4(Macrostructure- IS 11371)	-	1800	-
12.0 & 12.5(Ultrasnoic Test)	-	1800	-
12.0 & 12.6(Magnetic Particle Test - IS 10138 (P3))	-	1800	-
5(Manufacture)	-	100	-
7(Freedom from defects)	-	100	-
13(Marking)	-	100	-
12.7(Blue fracture test (IS:1875-1985))	-	1800	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	1500	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	1000	-

12 Jan, 2028

-
Included w.e.f 06.06.2025

137

IS 4992 (2024)

Door Handles for Mortice Locks â Specification (Second Revision)

19900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1(Fastening Elements and Spindle)	-	1000	-
Cl-6.2, Table-2 (i) a(Axial strength percent)	-	5000	-
Cl-6.2, Table-2 (i) b(Pre-load)	-	3000	-
Cl-6.2, Table-2 (i) c(Permanent deformation)	-	3000	-
Cl-6.3(Safety Requirements)	-	1000	-
Cl-6.4, Table-3 (1) a(Number of cycles)	-	10000	-
Cl-6.4, Table-3 (1) b(Force “P”)	-	5000	-
Cl-6.5(Corrosion Resistance)	-	5000	-
Cl-6.6(Fire Resistance Test)	-	5000	-
Cl-8(Marking)	-	1000	-
Cl-6.1(Fastening Elements and Spindle)	-	1000	-
Cl-6.2, Table-2 (i) a(Axial strength percent)	-	5000	-
Cl-6.2, Table-2 (i) b(Pre-load)	-	3000	-
Cl-6.2, Table-2 (i) c(Permanent deformation)	-	3000	-
Cl-6.3(Safety Requirements)	-	1000	-
Cl-6.4, Table-3 (1) a(Number of cycles)	-	10000	-
Cl-6.4, Table-3 (1) b(Force “P”)	-	5000	-
Cl-6.5(Corrosion Resistance)	-	5000	-
Cl-6.6(Fire Resistance Test)	-	5000	-
Cl-8(Marking)	-	1000	-
Cl-6.1(Fastening Elements and Spindle)	-	1000	-
Cl-6.2, Table-2 (i) a(Axial strength percent)	-	5000	-
Cl-6.2, Table-2 (i) b(Pre-load)	-	3000	-
Cl-6.2, Table-2 (i) c(Permanent deformation)	-	3000	-
Cl-6.3(Safety Requirements)	-	1000	-
Cl-6.4, Table-3 (1) a(Number of cycles)	-	10000	-
Cl-6.4, Table-3 (1) b(Force “P”)	-	5000	-
Cl-6.5(Corrosion Resistance)	-	5000	-
Cl-6.6(Fire Resistance Test)	-	5000	-
Cl-8(Marking)	-	1000	-

12 Jan, 2028

-
Included w.e.f 17.06.2025

138

IS 1364 : Part 1 (2023)

Hexagon head bolts, screws, and nuts of property grades A and B: Part 1 Hexagon head bolts (Size range M1.6 to M64) (sixth revision)

10300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Dimensions)	-	1000	-
Cl-5, Table-7(General requirements)	-	1000	-
Cl-5, Table-7(Thread-Tolerance class)	-	1000	-
Cl-5, Table-7(Mechanical properties- Steel)	-	8000	-
Cl-5, Table-7(Mechanical properties-Stainless steel)	-	8000	-
Cl-5, Table-7(Tolerances-Product grade)	-	1000	-
Cl-5, Table-7(Surface condition -Electroplated coatings)	-	1000	-
Cl-5, Table-7(Surface condition- Non-electrolytically applied zinc flake)	-	1000	-
Cl-5, Table-7(Surface condition - Hot dip galvanized coatings)	-	1000	-
Cl-5, Table-7(Surface integrity- Limits for surface discontinuities)	-	1000	-
Cl-6(Marking)	-	1000	-
Cl-4(Dimensions)	-	1000	-
Cl-5, Table-7(General requirements)	-	1000	-
Cl-5, Table-7(Thread-Tolerance class)	-	1000	-
Cl-5, Table-7(Mechanical properties- Steel)	-	8000	-
Cl-5, Table-7(Mechanical properties-Stainless steel)	-	8000	-
Cl-5, Table-7(Tolerances-Product grade)	-	1000	-
Cl-5, Table-7(Surface condition -Electroplated coatings)	-	1000	-
Cl-5, Table-7(Surface condition- Non-electrolytically applied zinc flake)	-	1000	-
Cl-5, Table-7(Surface condition - Hot dip galvanized coatings)	-	1000	-
Cl-5, Table-7(Surface integrity- Limits for surface discontinuities)	-	1000	-
Cl-6(Marking)	-	1000	-

12 Jan, 2028

-
Included w.e.f 06.06.2025

139

IS 1364 : Part 4 (2003)

Hexagon head bolts, screws and nuts of product grades A and B: Part 4 hexagon thin nuts (Chamfered) (Size Range M1.6t0 M64) (Fourth Revision)

10300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	1000	-
4, table 3(General requirements)	-	1000	-
4, table 3(Thread)	-	1000	-
4, table 3(Mechanical properties)	-	8000	-
4, table 3(Tolerances)	-	1000	-
4, table 3(Finish-coating)	-	1000	-
4, table 3(Surface integrity)	-	1000	-
4, table 3(Acceptability)	-	1000	-
5(Designation)	-	1000	-
3(Dimensions)	-	1000	-
4, table 3(General requirements)	-	1000	-
4, table 3(Thread)	-	1000	-
4, table 3(Mechanical properties)	-	8000	-
4, table 3(Tolerances)	-	1000	-
4, table 3(Finish-coating)	-	1000	-
4, table 3(Surface integrity)	-	1000	-
4, table 3(Acceptability)	-	1000	-
5(Designation)	-	1000	-

12 Jan, 2028

-
Included w.e.f 06.06.2025

140

IS 1364 : Part 6 (2018)

Hexagon Head Bolts, Screws and Nuts of Product Grades A and B Part 6 Hexagon Nuts, Style 2 ( First Revision )

10300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	1000	-
4, table 3(General requirements)	-	1000	-
4, table 3(Thread)	-	1000	-
4, table 3(Mechanical properties)	-	8000	-
4, table 3(Tolerances)	-	1000	-
4, table 3(Finish-coating)	-	1000	-
4, table 3(Surface integrity)	-	1000	-
4, table 3(Acceptability)	-	1000	-
5(Designation)	-	1000	-
3(Dimensions)	-	1000	-
4, table 3(General requirements)	-	1000	-
4, table 3(Thread)	-	1000	-
4, table 3(Mechanical properties)	-	8000	-
4, table 3(Tolerances)	-	1000	-
4, table 3(Finish-coating)	-	1000	-
4, table 3(Surface integrity)	-	1000	-
4, table 3(Acceptability)	-	1000	-
5(Designation)	-	1000	-

12 Jan, 2028

-
Included w.e.f 06.06.2025

141

IS 1364 : Part 2 (2023)

Hexagon head bolts screws and nuts of product grades A and B Part 2 Hexagon head screws (Size range M1.6 to M64 ) (Sixth revision of IS 1364 (Part 2))

10300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Dimensions)	-	1000	-
Cl-5, Table-5(General requirements)	-	1000	-
Cl-5, Table-5(Thread-Tolerance class)	-	1000	-
Cl-5, Table-5(Mechanical properties-Steel)	-	8000	-
Cl-5, Table-5(Mechanical properties-Stainless steel)	-	8000	-
Cl-5, Table-5(Tolerances- Product grade)	-	1000	-
Cl-5, Table-5(Surface condition -Electroplated coatings)	-	1000	-
Cl-5, Table-5(Surface condition- Non-electrolytically applied zinc flake)	-	1000	-
Cl-5, Table-5(Surface condition - Hot dip galvanized coatings)	-	1000	-
Cl-5, Table-5("Surface integrity -Limits for surface discontinuities")	-	1000	-
Cl-6(Marking)	-	1000	-
Cl-4(Dimensions)	-	1000	-
Cl-5, Table-5(General requirements)	-	1000	-
Cl-5, Table-5(Thread-Tolerance class)	-	1000	-
Cl-5, Table-5(Mechanical properties-Steel)	-	8000	-
Cl-5, Table-5(Mechanical properties-Stainless steel)	-	8000	-
Cl-5, Table-5(Tolerances- Product grade)	-	1000	-
Cl-5, Table-5(Surface condition -Electroplated coatings)	-	1000	-
Cl-5, Table-5(Surface condition- Non-electrolytically applied zinc flake)	-	1000	-
Cl-5, Table-5(Surface condition - Hot dip galvanized coatings)	-	1000	-
Cl-5, Table-5("Surface integrity -Limits for surface discontinuities")	-	1000	-
Cl-6(Marking)	-	1000	-

12 Jan, 2028

-
Included w.e.f 06.06.2025

142

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 7.1(CARBON)	-	200	-
Clause - 7.1(SULPHUR)	-	200	-
Clause - 7.1(PHOSPHURS)	-	200	-
Clause - 7.1(MANGANESE)	-	200	-
Clause - 7.1(NITROGEN)	-	200	-
As per Clause 10(Dimension)	-	100	-
As per Clause 10.1(Dimension Width)	-	100	-
As per Clause 10.1(Dimension Thickness)	-	100	-
As per Clause 10.2(Dimension Length)	-	100	-
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	100	-
As per Clause 11.5(Bend)	-	500	-
As per Clause 11.6(Camber)	-	100	-
As per Clause 11.7 (i)(Out of Square)	-	100	-
As per Clause 11.7 (ii)(Round Corners)	-	100	-
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	100	-
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	100	-
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	100	-
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	100	-
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	100	-
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	100	-
As per Clause 11.7 (ix)(Scarfing pits)	-	100	-
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	100	-
Clause. 13(Macro examination test.)	-	800	-
Clause. 13(Macro examination test.)	-	800	-
Clause. 13(Sulphur print.)	-	1500	-
Clause. 13(Inclusion content)	-	800	-
Clause. 14(Marking)	-	100	-
Clause.15(Ordering information)	-	100	-
Clause.6.0(Manufacture)	-	100	-
Clause.7.1(Silicon)	-	200	-
Clause.7.1(Carbon Equbalant)	-	200	-
Clause.7.1(Microalloy element)	-	1500	-

12 Jan, 2028

-
Exclusion: Cl.13., 1b (Sulphur print test)

143

IS 4992 (1975)

Specification for door handles for mortice locks (Vertical Type) (First Revision)

19900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1(Finish - Brass door handles shall have natural finish or shall be bright electro chromium plated. Aluminium alloy door handles shall be anodized )	-	3000	-
Cl. 8.1 (Ref. Cl.9 of IS 1868:1996)(Finish - Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	3000	-
4.1(MANUFACTURE AND CONSTRUCTION)	-	500	-
4.2(MANUFACTURE AND CONSTRUCTION)	-	500	-
5(DIMENSIONS AND TOLERANCES)	-	4000	-
6.1(Performance Requirments)	-	5000	-
6.2(Performance Requirments)	-	5000	-
7(WORKMANSHIP)	-	1000	-
7(WORKMANSHIP)	-	1000	-
8(FINISH)	-	10000	-
8(FINISH)	-	10000	-
8(FINISH)	-	10000	-

12 Jan, 2028

-
-

144

IS 12817 (2020)

Stainless Steel Butt Hinges - Specification ( Third Revision )

5800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2, Table 1 to 6(Length , A -IS 12817)	-	300	-
6.2, Table 1 to 6(Breadth, B-IS 12817)	-	300	-
6.2, Table 1 to 6(Breadth, B1-IS 12817)	-	300	-
6.2, Table 1 to 6(Breadth, B2-IS 12817)	-	300	-
6.2, Table 1 to 6(Thickness of flap, C-IS 12817)	-	300	-
6.2, Table 1 to 6(Dia. of Hinge pin, D-IS 12817 )	-	300	-
6.2, Table 1 to 6(Number of Knuckles- IS 12817 )	-	300	-
6.2, Table 1 to 6(Number of Screw Holes -IS 12817 )	-	300	-
6.2, Table 1 to 6(Holes for Screw Number- IS 12817 )	-	300	-
7.1(General - IS 12817 )	-	300	-
7.2(Knuckles - IS 12817 )	-	300	-
7.3(Pins- IS 12817 )	-	300	-
7.4(Screw Holes- IS 12817 )	-	300	-
7.4.2(Position of screw holes - IS 12817 )	-	300	-
7.4.2, Fig 1(The distance of the screw holes from the end of the flap - IS 12817 )	-	300	-
8.0(Finish - IS 12817 )	-	300	-
Clause 4.1.2(Silicon (Pin) )	-	200	-
Clause 4.1.2(Phosphorus (Pin) )	-	200	-
Clause 4.1.2(Sulphur (Pin) )	-	200	-
Clause 4.1.2(Manganese (Pin) )	-	200	-
Clause 4.1.2(Carbon (Pin) )	-	200	-
Clause 4.1.1(Silicon (Flap) )	-	200	-
Clause 4.1.1(Phosphorus (Flap) )	-	200	-
Clause 4.1.1(Sulphur (Flap) )	-	200	-
Clause 4.1.1(Manganese (Flap) )	-	200	-
Clause 4.1.1(Carbon (Flap) )	-	200	-
Clause 7.4.2 (Dimension - Z )	-	100	-
Clause 7.4.2 (Dimension - Y )	-	100	-
Clause 7.4.2 (Dimension - X )	-	100	-
Clause 7.4.1(Number of holes)	-	100	-
As per Cl.4(Carbon)	-	200	-
As per Cl.4(Sulphur)	-	200	-
As per Cl.4(Phosphorus)	-	200	-
As per Cl.4(Manganese)	-	200	-
As per Cl.4(Nitrogen)	-	200	-
As per Cl.4(Silicon)	-	200	-
As per Cl.4(Aluminium)	-	200	-
As per Cl.4(Chromium)	-	200	-
As per Cl.4(Vanadium)	-	200	-
As per Cl.4(Molybdenum)	-	200	-
As per Cl.4(Niobium)	-	200	-
As per Cl.4(Nickel)	-	200	-
As per Cl.4(Copper)	-	200	-
As per Cl.4(Titanium)	-	200	-
As per Cl.4(Zirconium)	-	200	-
As per Cl.4(Tungsten)	-	200	-
As per Cl.4(Cerium)	-	200	-

12 Jan, 2028

-
-

145

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

19800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 50 cycles)	-	2500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 25 cycles)	-	2500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 10 cycles)	-	2500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	2500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 50 cycles)	-	2500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 25 cycles)	-	2500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 10 cycles)	-	2500	-
Clause 7.3, Annex G(Average Breaking Load)	-	1500	-
Clause 7.3, Annex G(Individual Breaking Load)	-	1500	-
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	1500	-
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	1500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	2000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	800	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	4000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	1500	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	800	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	800	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	200	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	200	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	200	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	200	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	200	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	200	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	100	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	100	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	100	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	100	-
Clause 6.3 (Bonding and Delamination between the layers of paver blocks)	-	100	-
Clause 7.1.3 (Colour and Texture)	-	100	-
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	100	-
Clause 7.1.1 (General Quality)	-	100	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	100	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	100	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	100	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	100	-
Clause 3.20(Spacer nibs)	-	100	-
10(Marking)	-	100	-
cl.5(Cement)	-	8000	-
5.2(Mineral Admixture)	-	5000	-
5.3(Chemical Admixtures)	-	5000	-
5.4(Coarse and Fine Aggregates)	-	5000	-
5.5(Pigments)	-	3000	-
5.6(Water)	-	5000	-

12 Jan, 2028

-
Cl.7.3 & Cl.9.1.4, Table-3 SI No. (vi) (freeze Thaw durability)

146

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	100	-
Cl 15(Length, Width & Thickness)	-	100	-
Cl 13(Y Groove Cracking Test)	-	2500	-
Cl 12(Sudden Load Applied)	-	1500	-
Cl 11.3(Press)	-	1500	-
Cl 10.3(UTM)	-	1500	-
Cl 7(Workmanship)	-	100	-
Cl 18(Weight)	-	100	-
Cl 15(Length, Width & Thickness)	-	100	-
Cl 13(Y Groove Cracking Test)	-	2500	-
Cl 12(Sudden Load Applied)	-	1500	-
Cl 11.3(Press)	-	1500	-
Cl 10.3(UTM)	-	1500	-
Cl 7(Workmanship)	-	100	-
Cl 18(Weight)	-	100	-
Cl 15(Length, Width & Thickness)	-	100	-
Cl 13(Y Groove Cracking Test)	-	2500	-
Cl 12(Sudden Load Applied)	-	1500	-
Cl 11.3(Press)	-	1500	-
Cl 10.3(UTM)	-	1500	-
Cl 7(Workmanship)	-	100	-
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	200	-
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	100	-
Cl. 15(Cl. 15 Channel Section: Camber)	-	100	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	100	-
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	100	-
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	100	-
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	100	-
Cl. 15(Cl. 15 Channel Section: Depth)	-	100	-
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	100	-
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	100	-
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	100	-
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	100	-
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	100	-
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	100	-
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	500	-
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	500	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	500	-
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E275, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E275, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E275, CARBON)	-	200	-
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	200	-
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	200	-
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	200	-
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	200	-
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	200	-
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	200	-
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	200	-
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 15, 16(Off Centre of Web)	-	100	-
Cl. 15, 16(Flange out of square (I beam))	-	100	-
Cl. 15, 16(Width of flange (I Beam))	-	100	-
Cl. 15, 16(Depth (I Beam))	-	100	-
Cl. 15, 16(Mass (Plate))	-	100	-
Cl. 15, 16(Flange Slope)	-	100	-
Cl. 15, 16(Web Thickness)	-	100	-
Cl. 15, 16(Flange Thickness)	-	100	-
Cl. 15, 16(Out of Square (Flat))	-	100	-
Cl. 15, 16(Width )	-	100	-
Cl. 15, 16(Thickness )	-	100	-
Cl. 15, 16(Sectional Area )	-	100	-
Cl. 15, 16(Camber (Angle))	-	100	-
Cl. 15, 16(Out of Square (Angle))	-	100	-
Cl. 15, 16(Weight)	-	100	-
Cl. 15, 16(Leg Length Difference (Angle))	-	100	-
Cl. 15, 16(Leg Length B (Angle))	-	100	-
Cl. 15, 16(Leg Length A (Angle))	-	100	-
Cl. 15, 16(Toe Radius R2)	-	100	-
Cl. 15, 16(Root Radius R1)	-	100	-
Cl 18(Weight)	-	100	-
Cl 15(Length, Width & Thickness)	-	100	-
Cl 13(Y Groove Cracking Test)	-	2500	-
Cl 12(Sudden Load Applied)	-	1500	-
Cl 11.3(Press)	-	1500	-
Cl 10.3(UTM)	-	1500	-
Cl 7(Workmanship)	-	100	-
14.1(Soundness test)	-	1500	-
14.2(Grain Size)	-	800	-
14.2(Inclusion)	-	2500	-
Cl 7(Workmanship)	-	100	-
Cl 10.3(UTM)	-	1500	-
Cl 11.3(Press)	-	1500	-
Cl 12(Sudden Load Applied)	-	1500	-
Cl 13(Y Groove Cracking Test)	-	2500	-
Cl 15(Length, Width & Thickness)	-	100	-
Cl 18(Weight)	-	100	-
Clause 8, Table 1, Note 2(Any Instrumental Method/Chemical Method)	-	2000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	2000	-
Clause 8, Table 1, Note 5(Any Instrumental Method/Chemical Method)	-	2000	-
Clause 8, Table 1, Note 5(By Calculation)	-	100	-
Clause 8, Table 1, Note 6(Any Instrumental Method/Chemical Method)	-	2000	-
Clause 8, Table 1, Note 6(By Calculation)	-	100	-
Clause 7(IS 2062)	-	1500	-
Clause 11.3(IS 1599)	-	500	-
Clause 12(IS 1757)	-	800	-
Clause 15, Table 4(IS 2062)	-	1500	-
16(Tolerance)	-	100	-
20(Marking)	-	100	-
20(MARKING)	-	100	-
8(Micro Alloying elements)	-	2000	-
8(Niobium as Nb)	-	200	-
8(Vanadium as V)	-	200	-
8(Titanium as Ti)	-	200	-
10(Tensile Strength-IS:1608(P1)-22)	-	1500	-
10(Yield Stress-IS:1608(P1)-22)	-	500	-
10(Elongation on SoA 5.65mm GL)	-	500	-
15(Mass -SOP MT-23)	-	100	-
15(Sectional Area)	-	100	-
15(Dimension -D)	-	100	-
15(Dimension -B)	-	100	-
15(Thickness - t)	-	100	-
15(Thickness - T)	-	100	-
15(Flange Slope)	-	100	-
15(Radius R1)	-	100	-
15(Radius R2)	-	100	-
15(Mass -SOP MT-23)	-	100	-
15(Sectional Area)	-	100	-
15(Dimension -D)	-	100	-
15(Dimension -B)	-	100	-
15(Thickness - t)	-	100	-
15(Thickness - T)	-	100	-
15(Radius R1)	-	100	-
15(Radius R2)	-	100	-
15(Mass -SOP MT-23)	-	100	-
15(Sectional Area)	-	100	-
15(Dimensions AxB)	-	100	-
15(Thickness - t)	-	100	-
15(Radius -R1)	-	100	-
15(Radius -R2)	-	100	-
15(Diameter)	-	100	-
15(Sectional Area)	-	100	-
15(Mass per metre)	-	100	-
15(Mass per metre)	-	100	-
15(Ovality)	-	100	-
15(Side Width)	-	100	-
15(Sectional Area)	-	100	-
15(Mass per metre)	-	100	-
15(Out of Square)	-	100	-
9(Preparation of test sample)	-	100	-
Clause 8, Table 1, Note 2(Aluminium)	-	200	-
Clause 8, Table 1, Note 5(Niobium)	-	200	-
Clause 8, Table 1, Note 5(Titanium)	-	200	-
Clause 8, Table 1, Note 5(Nb+V+Ti)	-	200	-
Clause 8, Table 1, Note 6(Boron)	-	200	-
Clause 8, Table 1, Note 6(Cr+Ni)	-	200	-
Clause 7(Freedom from Defect)	-	100	-
Clause 11.3(Bend Test)	-	100	-
Clause 12(Impact Test)	-	1500	-
Clause 15, Table 4(Dimension)	-	100	-
5(General Requirements)	-	100	-
4(MARKING)	-	100	-

12 Jan, 2028

-
Exclusion: Cl.13 (Y Groove Cracking Test), Cl.14.1 (Soundness test, Non- Destructive Test)

147

IS 1865 (1991)

Iron castings with spheroidal or nodular graphite - Specification (Third Revision)

9800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Grades)	-	2000	-
4.1(General requirements)	-	1000	-
5(Manufacture)	-	1000	-
9(Micro structure)	-	1500	-
10.1(Separately-Cast Test Samples)	-	1500	-
10.2(Cast-on Test Samples)	-	1500	-
11.1(Batch)	-	100	-
11.2(Number of Tests per Batch)	-	100	-
12.1(Tensile Strength)	-	1500	-
12.2(Impact Test)	-	2500	-
13.1(Tensile Test)	-	1500	-
13.2(Hardness Test)	-	1000	-
13.3(Impact Test)	-	2500	-
14(Validity of tests)	-	100	-
15(Retest)	-	100	-
16(Additional test)	-	100	-
17(Marking)	-	100	-
6(Workmanship and finish)	-	100	-
7(Heat treatment)	-	100	-

12 Jan, 2028

-
-

148

IS 1367 : Part 6 (2018)

Technical supply conditions for threaded steel fasteners: Part 6 mechanical properties of fasteners made of carbon steel and alloy steel - Nuts with specified property classes - Coarse thread and fine pitch thread (Fourth Revision)

7300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Material Testing)	-	3000	-
9.1(Proof Load)	-	4000	-
9.2(Hardness Test)	-	1500	-
9.3(Surface Integrity)	-	1000	-
Cl-4.3(Ranges of nominal diameters in relation to nut style and property class)	-	1000	-

12 Jan, 2028

-
-

149

IS 1367 : Part 3 (2017)

Technical supply conditions for threaded steel fasteners: Part 3 mechanical properties of fasteners made of carbon steel and bolts, screws and studs (Fifth Revision)

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Material Testing)	-	2000	-
7.0(Mechanical testing (Ys, TS, %EL, RA))	-	1500	-
9.6(Proof Load test for finished bolts scrwes, and studs)	-	3000	-
9.8(Head soundness test)	-	2000	-
9.9(Hardness Test)	-	1500	-
9.10(Decarburization test)	-	2500	-
9.11(Carburization test)	-	2500	-
9.14(Impact Test)	-	4000	-
9.12(Reducing of hardnes after retempering , Hv)	-	2000	-
9.13(Torsional Test)	-	4000	-
9.15(Surface discounity)	-	100	-

12 Jan, 2028

-
Exclusion: Cl.9.13 (Torsional Test)

150

IS 210 (2009)

Grey iron castings - Specification (First Revision)

Grey iron castings

6900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	2000	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	1500	-
7.1(WORKMANSHIP AND FINISH)	-	100	-
10.1(FREEDOM FROM DEFECTS)	-	100	-
10.2(FREEDOM FROM DEFECTS)	-	100	-
13(SIZE OF TEST BARS-Diameter)	-	100	-
13(SIZE OF TEST BARS-Length)	-	100	-
16, Table 3(Hardness Test)	-	500	-
17,Annex B(TRANSVERSE TEST)	-	1500	-
9(IS 7754)	-	800	-
9(IS 7754)	-	800	-
9(Microstructure)	-	1800	-
21(Marking)	-	100	-
9(Microstructure)	-	1800	-
6(Chemical Composition(chemical composition shall be as agreed to between the purchaser and the manufacturer.))	-	2000	-
7.1(WORKMANSHIP AND FINISH)	-	100	-
10.1(FREEDOM FROM DEFECTS)	-	100	-
10.2(FREEDOM FROM DEFECTS)	-	100	-
13(SIZE OF TEST BARS-Diameter)	-	100	-
13(SIZE OF TEST BARS-Length)	-	100	-
15, Table 3(TENSIL.E TEST- IS 1608 Part1 )	-	1500	-
16, Table 3(Hardness Test)	-	500	-
17,Annex B(TRANSVERSE TEST)	-	1500	-
18(HYDROSTATIC TEST)	-	1500	-
18(HYDROSTATIC TEST)	-	1500	-

12 Jan, 2028

-
Exclusion: Cl.18 (Hydrostatic Test)

Bureau of Indian Standards

The National Standards Body of India

(suspended) Rajkot Metlab Services LLP, Rajkot

PL 29 30 Nr Tulip Party Plot, GONDAL ROAD, VAVDI, Rajkot, Rajkot, Gujarat, 360004

9725213602 testing@rajkotlab.com

Scope List