BIS - LIMS (Laboratory Information Management System)

IEC TEST LABS LLP

Ground Floor, Plot No. N-47, Pkt-N, Sector-5, Bawana, DSIDC, Delhi-110039, Delhi, North West, Delhi, 110039

9871727340 iectestlabs@gmail.com

Scope List

Reset

53 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 9968 : Part 1 (2025)

Elastomer Insulated Cables - Specification Part 1 for Working Voltages up to and including 1100 volts (Second Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Copper Conductor)	-	1000	-
Cl-4.2(Aluminum Conductor)	-	1000	-
Cl-6.1(Proofed Tape)	-	1000	-
Cl-6.2("Polyethylene Terephthalate (PETP) Tape or Plastic Tape or Any Other Suitable Tape")	-	1000	-
Cl-6.3(Glass Tape)	-	1000	-
Cl-7(Fillers)	-	1000	-
Cl-8.1(Textile Braid)	-	1000	-
Cl-8.2(Glass Braid)	-	1000	-
Cl-9.1(General Service Insulated Cables and Flexible Cords)	-	1000	-
Cl-9.2(Heat Resisting Insulated Cables)	-	1000	-
Cl-9.3(Silicon Rubber Insulated Cable)	-	1000	-
Cl-10.1(Preservative Compound)	-	1000	-
Cl-10.2(Varnish)	-	1000	-
Cl-12(separator tape)	-	1000	-
Cl-14(Core Identification)	-	1000	-
Cl-18(Laying UP of Cores)	-	1000	-
Cl-19(Binder Tape)	-	1000	-
Cl-20.2(Thickness of Sheath)	-	1000	-
Cl-20.3(Tolerance on Thickness of Sheath)	-	1000	-
Cl-20.4(Colour)	-	1000	-
Cl-22.1 (i) (a)(Conductor resistance test)	-	1000	-
Cl-22.1 (i) (b)(High voltage test or spark test.)	-	2000	-
Cl-22.1 (ii) (a)(Annealing test (for copper);)	-	1000	-
Cl-22.1 (ii) (b)(Tensile Test ((for aluminium);)	-	1000	-
Cl-22.1 (ii) (c)(Wrapping test (for aluminium);)	-	1000	-
Cl-22.1 (ii) (f)(Tensile strength and elongation at break of insulation and sheath)	-	1000	-
Cl-22.1 (ii) (g)(Hot set test for insulation and sheath)	-	2000	-
Cl-22.1 (ii) (h)(High voltage test)	-	2000	-
Cl-22.1 (ii) (i)(Insulation resistance test)	-	2000	-
Cl-22.1 (iii) (a)(Persulphate test (for tinned copper);)	-	2000	-
Cl-22.1 (iii) (f)(Test for thickness of insulation and sheath and overall diameter)	-	1000	-
Electrical(Tensile strength and elongation at break)	-	1000	-
Cl-22.1 (iii) (g), 2(Ageing in air oven)	-	5000	-
Cl-22.1 (iii) (g), 3(Ageing in air bomb)	-	5000	-
Cl-22.1 (iii) (g), 4(Ageing In oxygen bomb)	-	5000	-
Cl-22.1 (iii) (g), 5(Hot set)	-	2000	-
Cl-22.1 (iii) (g), 6(Oil resistance;)	-	2000	-
Cl-22.1 (iii) (g), 7(Tear resistance)	-	2000	-
Cl-22.1 (iii) (i)(High voltage (water immersion) test;)	-	2000	-
Cl-22.1 (iii) (j)(Flammability test)	-	1000	-
Cl-22.1 (iii) (k)(Water absorption test (for insulation as applicable))	-	5000	-
Cl-24.1(Manufacturer’s Identification)	-	1000	-
Cl-25(Packing and Morning)	-	1000	-

07 Sep, 2026

-
included w.e.f 09.02.2026

IS 15652 (2006)

Insulating mats for electrical purposes - Specification

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	1000	-
10.a)(Packing)	-	1000	-
10.b)(Packing)	-	1000	-
10.c)(Packing)	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	1000	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Extreme Low Temperature (Cl.8.6))	-	2000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	1000	-
10(Packing)	-	1000	-
10(Packing)	-	1000	-
10(Packing)	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	1000	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	2000	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Extreme Low Temperature (Cl.8.6))	-	2000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	1000	-
10.a)(Packing)	-	1000	-
10.b)(Packing)	-	1000	-
10.c)(Packing)	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	1000	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Extreme Low Temperature (Cl.8.6))	-	3000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.1 of IS 15652 : 2006))	-	1000	-
9(Marking (As per Cl.9.2 of IS 15652 : 2006))	-	1000	-
10(Packing)	-	1000	-
10(Packing)	-	1000	-
10(Packing)	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.1 and Table-1 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
4(Classification and Designation (As per Cl.4.2 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.1 of IS 15652 : 2006))	-	1000	-
5(Composition (As per Cl. 5.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Shape Requirements and Dimension (As per Cl.6.1 & 6.2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Thickness [mm] (As per Cl. 6.3 and Table-2 of IS 15652 : 2006))	-	1000	-
6(Colour (As per Cl. 6.4 of IS 15652 : 2006))	-	1000	-
7(Workmanship & Finish (As per Cl. 7.1 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.1 and Table - 3 of IS 15652 : 2006))	-	1000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.3 of IS 15652 : 2006))	-	2000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Physical properties (As per Cl.8.5 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.1 and C-3.1 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.2 and C-3.2 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and C-3.3 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (As per Cl.8.2.3 and Table-4 of IS 15652 : 2006))	-	3000	-
8(Di-electric Properties (Cl.8.2), A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(A.C. Proof Voltage (Cl.8.2.4), C-3.4 and Table-5 of IS 15652 : 2006))	-	5000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Thermal Properties (Cl..8.4))	-	2000	-
8(Extreme Low Temperature (Cl.8.6))	-	3000	-

07 Sep, 2026

-
Included w.e.f 23.12.2025

IS 16242 : Part 1 (2025)

Uninterruptible power systems UPS Part 1 Safety requirements (first revision)

125000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Fault and abnormal conditions)	-	5000	10% Discount for BIS
Cl-4.3(Short-circuit and overload protection)	-	3000	10% Discount for BIS
Cl-4.3.101(AC input current)	-	5000	10% Discount for BIS
Cl-4.3.102(Transformer protection)	-	4000	10% Discount for BIS
Cl-4.3.103(AC input short-circuit current)	-	3000	10% Discount for BIS
Cl-4.3.104(Protection of the energy storage device)	-	4000	10% Discount for BIS
Cl-4.3.105(Unsynchronised load transfer)	-	2000	10% Discount for BIS
Cl-4.4(Protection against electric shock)	-	4000	10% Discount for BIS
Cl-4.4.2.2.2(Selection tables for contact area and skin humidity condition)	-	5000	10% Discount for BIS
Cl-4.4.3.3(Protection by means of enclosures or barriers- Openings)	-	3000	10% Discount for BIS
Cl-4.4.7.1.1(Influencing factors)	-	2000	10% Discount for BIS
Cl-4.4.7.1.2(Pollution degree)	-	2000	10% Discount for BIS
Cl-4.4.7.1.3(Overvoltage category (OVC))	-	4000	10% Discount for BIS
Cl-4.4.7.7(PWB spacings for functional insulation)	-	2000	10% Discount for BIS
Cl-4.4.9(Capacitor discharge)	-	5000	10% Discount for BIS
Cl-4.5.2(Service access areas)	-	3000	10% Discount for BIS
Cl-4.6(Protection against fire and thermal hazards)	-	5000	10% Discount for BIS
Cl-4.6.2.2(Components within a circuit representing a fire hazard)	-	2000	10% Discount for BIS
Cl-4.6.3.1(General)	-	2000	10% Discount for BIS
Cl-4.6.3.2(Flammability of enclosure materials)	-	5000	10% Discount for BIS
Cl-4.6.3.3.2(Openings in the top and side of fire enclosures)	-	4000	10% Discount for BIS
Cl-4.6.4.1(Temperature limits- Internal parts)	-	5000	10% Discount for BIS
Cl- 4.6.5(Limited power sources)	-	5000	10% Discount for BIS
Cl-4.7(Protection against mechanical hazards)	-	4000	10% Discount for BIS
Clause 4(Protection against hazards)	-	3000	10% Discount for BIS
Cl-4.7.101(Protection in service access area)	-	2000	10% Discount for BIS
Clause 5(Test requirements)	-	5000	10% Discount for BIS
Cl-4.8 .101(Equipment with multiple sources of supply- General)	-	4000	10% Discount for BIS
Clause 5.2.2(Mechanical tests)	-	5000	10% Discount for BIS
Clause 5.2.3(Electrical tests)	-	3000	10% Discount for BIS
Cl-4.9(Protection against environmental stresses)	-	4000	10% Discount for BIS
Cl-4.10(Protection against sonic pressure hazards)	-	3000	10% Discount for BIS
Clause 5.2.4("Abnormal operation tests")	-	5000	10% Discount for BIS
Cl-4.11(Wiring and connections)	-	2000	10% Discount for BIS
Clause 5.2.5(Material tests)	-	4000	10% Discount for BIS
Clause 5.2.6(Environmental tests)	-	3000	10% Discount for BIS
Cl-4.11.101.1(Non-detachable cords- Cord guard)	-	5000	10% Discount for BIS
Clause 5.2.7(Hydrostatic pressure test)	-	3000	10% Discount for BIS
Cl-4.11.101.2(Cord anchorages and strain relief)	-	5000	10% Discount for BIS
Clause 6(Information and marking requirements)	-	5000	10% Discount for BIS
Cl-4.101.1(Emergency switching (disconnect) device)	-	3000	10% Discount for BIS
Clause 6.1.101(Durability)	-	5000	10% Discount for BIS
Cl-4.101.2(Normal disconnect devices)	-	3000	10% Discount for BIS
Cl-4.102.1(Stored energy source- General)	-	2000	10% Discount for BIS
Cl-4.102.2(Accessibility and maintainability)	-	3000	10% Discount for BIS
Cl-4.102.3(Distance between battery cells)	-	2000	10% Discount for BIS
Cl- 4.102.5(Electrolyte spillage)	-	3000	10% Discount for BIS
Cl- 4.102.6(Ventilation and hydrogen concentration)	-	2000	10% Discount for BIS
Cl- 4.102.8.1(Overcurrent and earth fault protection)	-	4000	10% Discount for BIS
Cl- 4.102.8.2(Location of protective devices)	-	5000	10% Discount for BIS
Cl-4.102.8.3(Rating of protective devices)	-	2000	10% Discount for BIS
Cl-4.103(UPS connection to telecommunication lines)	-	4000	10% Discount for BIS
Cl-5.1.5.3(Operating parameters for tests)	-	3000	10% Discount for BIS
Cl-5.1.7(Test overview)	-	2000	10% Discount for BIS
Cl-5.2.2.2(Non-accessibility test)	-	4000	10% Discount for BIS
Cl-5.2.2.4.4(Drop test)	-	5000	10% Discount for BIS
Cl-4.8.102(Backfeed protection)	-	5000	10% Discount for BIS
Cl- 4.102.7(Charging voltages)	-	4000	10% Discount for BIS
Cl-5.2.2.6.101(Wall or ceiling mounted equipment test)	-	5000	10% Discount for BIS
Cl-5.2.2.6.102(Rack mounted equipment test)	-	4000	10% Discount for BIS
Cl-5.2.2.101(Cord guard test)	-	3000	10% Discount for BIS
Cl-5.2.3.9(Limited power source test)	-	5000	10% Discount for BIS
Cl-5.2.3.10(Temperature rise test)	-	5000	10% Discount for BIS
Cl-5.2.3.101.1(Backfeed protection test- General)	-	5000	10% Discount for BIS
Cl-5.2.3.101.2(Test for pluggable UPS)	-	5000	10% Discount for BIS
Cl-5.2.3.101.3(Test for permanently connected UPS)	-	5000	10% Discount for BIS
Cl-5.2.3.101.4(Method to simulate the load-induced change of reference potential for pluggable UPS)	-	4000	10% Discount for BIS
Cl-5.2.3.101.5(Solid-state backfeed protection)	-	3000	10% Discount for BIS
Cl-5.2.3.102(Input current test)	-	5000	10% Discount for BIS
Cl-5.2.3.103(Short-time withstand current test)	-	3000	10% Discount for BIS
Cl-5.2.3103.3(Input port short-time withstand current rating)	-	2000	10% Discount for BIS
Cl-5.2.3.104(Transformer protection test)	-	2000	10% Discount for BIS
Cl- 5.2.3.105(Unsynchronised load transfer test)	-	2000	10% Discount for BIS
Cl-5.2.4.1(Abnormal operation and simulated faults tests- General)	-	3000	10% Discount for BIS
Cl-5.2.6.4(Vibration test)	-	4000	10% Discount for BIS
Cl-5.2.6.5(Salt mist test)	-	3000	10% Discount for BIS
Cl-5.2.6.6(Dust and sand test)	-	5000	10% Discount for BIS
Cl-6(Information and marking requirements)	-	5000	10% Discount for BIS

07 Sep, 2026

-
Included w.e.f. 15.10.2025

IS 398 : Part 2 (2025)

Aluminium Conductor for Overhead Transmission Purposes - Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced (Fourth Revision)

18000 View breakup
Rs. 18000/- (up to 100 Sq.mm), Rs. 100000/- (150 Sq.mm to 200 Sq.mm), Rs. 125000/- (400 Sq.mm to 560 Sq.mm)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Material)	-	1000	Rs. 18000/- (up to 100 Sq.mm), Rs. 100000/- (150 Sq.mm to 200 Sq.mm), Rs. 125000/- (400 Sq.mm to 560 Sq.mm)
Cl-6.1.1(chemical composition of high carbon steel)	-	2000	-
Cl-6.2(zinc used for galvanizing)	-	1000	-
Cl-7(Freedom From Defects)	-	1000	-
Cl-8.1(Wires-Nominal Sizes)	-	1000	-
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	1000	-
Cl-9.1(Joint in Wires)	-	1000	-
Cl-9.2(Aluminium Wires)	-	1000	-
Cl-9.3(Galvanized Steel Wires)	-	1000	-
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	2000	-
Cl-13.3(Conductor- Visual examination)	-	1000	-
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	2000	-
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	5000	-
Cl- 13.14(Conductor- Ultimate tensile strength test on stranded conductor)	-	10000	-
Cl- 13.13(Conductor- Surface condition test on stranded conductor)	-	10000	-
Cl- 13.15(Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.))	-	0	-
Cl-13.16(Conductor- Radio interference voltage test)	-	0	-
Cl-13.4(Aluminium wires-Measurement of diameter)	-	5000	-
Cl- 13.6(Aluminium wires -Breaking load test)	-	5000	-
Cl- 13.8(Aluminium wires- Wrapping test)	-	5000	-
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	5000	-
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	5000	-
Cl- 13.4(Steel wires- Measurement of diameter)	-	2000	-
Cl- 13.6(Steel wires- Breaking load test)	-	2000	-
Cl- 13.7(Steel wires- Ductility test)	-	2000	-
Cl- 13.8(Steel wires- Wrapping test)	-	2000	-
Cl- 13.10(Steel wires- Galvanizing test)	-	2000	-
Cl-13.7.1(Torsion Test)	-	2000	-
Cl-13.7.2(Elongation Test)	-	2000	-
Cl-11.1(Standard Length)	-	1000	-
Cl-11.2(Random Lengths)	-	1000	-
Cl-6(Material)	-	1000	-
Cl-6.1.1(chemical composition of high carbon steel)	-	2000	-
Cl-6.2(zinc used for galvanizing)	-	1000	-
Cl-7(Freedom From Defects)	-	1000	-
Cl-8.1(Wires-Nominal Sizes)	-	2000	-
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	2000	-
Cl-9.1(Joint in Wires)	-	1000	-
Cl-9.2(Aluminium Wires)	-	1000	-
Cl-9.3(Galvanized Steel Wires)	-	1000	-
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	2000	-
Cl-13.3(Conductor- Visual examination)	-	1000	-
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	2000	-
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	5000	-
Cl- 13.14(Conductor- Ultimate tensile strength test on stranded conductor)	-	10000	-
Cl- 13.13(Conductor- Surface condition test on stranded conductor)	-	10000	-
Cl- 13.15(Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.))	-	0	-
Cl-13.16(Conductor- Radio interference voltage test)	-	0	-
Cl-13.4(Aluminium wires-Measurement of diameter)	-	2000	-
Cl- 13.6(Aluminium wires -Breaking load test)	-	2000	-
Cl- 13.8(Aluminium wires- Wrapping test)	-	2000	-
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	5000	-
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	2000	-
Cl- 13.4(Steel wires- Measurement of diameter)	-	2000	-
Cl- 13.6(Steel wires- Breaking load test)	-	2000	-
Cl- 13.7(Steel wires- Ductility test)	-	5000	-
Cl- 13.8(Steel wires- Wrapping test)	-	5000	-
Cl- 13.10(Steel wires- Galvanizing test)	-	5000	-
Cl-13.7.1(Torsion Test)	-	2000	-
Cl-13.7.2(Elongation Test)	-	2000	-
Cl-11.1(Standard Length)	-	1000	-
Cl-11.2(Random Lengths)	-	1000	-
Cl-6(Material)	-	1000	-
Cl-6.1.1(chemical composition of high carbon steel)	-	2000	-
Cl-6.2(zinc used for galvanizing)	-	1000	-
Cl-7(Freedom From Defects)	-	1000	-
Cl-8.1(Wires-Nominal Sizes)	-	1000	-
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	1000	-
Cl-9.1(Joint in Wires)	-	1000	-
Cl-9.2(Aluminium Wires)	-	1000	-
Cl-9.3(Galvanized Steel Wires)	-	1000	-
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	1000	-
Cl-13.3(Conductor- Visual examination)	-	1000	-
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	2000	-
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	2000	-
Cl- 13.14(Conductor- Ultimate tensile strength test on stranded conductor)	-	10000	-
Cl- 13.13(Conductor- Surface condition test on stranded conductor)	-	10000	-
Cl- 13.15(Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.))	-	0	-
Cl-13.16(Conductor- Radio interference voltage test)	-	0	-
Cl-13.4(Aluminium wires-Measurement of diameter)	-	1000	-
Cl- 13.6(Aluminium wires -Breaking load test)	-	1000	-
Cl- 13.8(Aluminium wires- Wrapping test)	-	1000	-
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	2000	-
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	2000	-
Cl- 13.4(Steel wires- Measurement of diameter)	-	2000	-
Cl- 13.6(Steel wires- Breaking load test)	-	2000	-
Cl- 13.7(Steel wires- Ductility test)	-	2000	-
Cl- 13.8(Steel wires- Wrapping test)	-	2000	-
Cl- 13.10(Steel wires- Galvanizing test)	-	2000	-
Cl-13.7.1(Torsion Test)	-	2000	-
Cl-13.7.2(Elongation Test)	-	2000	-
Cl-11.1(Standard Length)	-	1000	-
Cl-11.2(Random Lengths)	-	1000	-

07 Sep, 2026

-
Included w.e.f 27.11.2025 Exclusion: Cl- 13.15 (Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.)),Cl-13.16 (Conductor- Radio interference voltage test)

IS 7098 : Part 1 (2025)

Crosslinked Polyethylene Insulated Thermoplastic Sheathed Cables - Specification Part 1 For Working Voltages up to and Including 1 100 Volts (Second Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Conductors -Material)	-	1000	-
Cl-5, Table-1 (i)(Tensile strength)	-	2000	-
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	2000	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	3000	-
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	3000	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	2000	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	2000	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	2000	-
Cl-5, Table-1 (iv)(Shrinkage)	-	2000	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	5000	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	2000	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	1000	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	1000	-
Cl-7(Armouring)	-	1000	-
Cl-8(Outer Sheath)	-	1000	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	2000	-
Cl-11(Core Identification)	-	1000	-
Cl-12(Laying up of Cores)	-	1000	-
Cl-13(Inner Sheath (Common Covering))	-	1000	-
Cl-14.1(Armouring- Application)	-	1000	-
Cl-14.1.2(armour round wires/formed wires)	-	1000	-
Cl-14.2(Type of Armour)	-	1000	-
Cl-14.3(Dimensions)	-	2000	-
Cl-14.4(Joints)	-	1000	-
Cl-14.5(Resistance)	-	2000	-
Cl-15.3(Thickness of Outer Sheath)	-	2000	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	2000	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	2000	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	2000	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	2000	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	2000	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	2000	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	2000	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	2000	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	2000	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	2000	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	2000	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	2000	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	2000	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	3000	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	3000	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	2000	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	2000	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	2000	-
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	2000	-
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	2000	-
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	5000	-
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	2000	-
Cl-17.2(High voltage test)	-	2000	-
Cl-17.3(Flammability test)	-	2000	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	3000	-
Cl-17.5(Flame retardance test on single cable)	-	2000	-
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	5000	-
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	3000	-
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	3000	-
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	3000	-
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	3000	-
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	5000	-
Cl-16.4 (i)(Cold bend test for outer sheath)	-	2000	-
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	2000	-
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	2000	-

07 Sep, 2026

-
Included w.e.f. 15.10.2025

IS 1554 : Part 2 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 2 for working voltages from 3.3 kV up to and including 11 kV (Second Revision)

115000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CONDUCTOR)	-	2000	Rs.115000/- upto 3.8kV/6.6kV
3.1.1(CONDUCTOR)	-	2000	-
4.1(INSULATION)	-	2000	-
5.1(SCREENING)	-	2000	-
5.1.1(Non-magnetic Metallic Tape for SingleCore Unscreened and Unarmoured Cables)	-	2000	-
6.1(FILLERS AND INNER SHEATH)	-	2000	-
6.2(FILLERS AND INNER SHEATH)	-	2000	-
7.1(ARMOURING)	-	2000	-
7.2(ARMOURING)	-	2000	-
8.1(OUTER SHEATH)	-	2000	-
9.1(CONDUCTOR)	-	2000	-
9.2(CONDUCTOR)	-	2000	-
10.1(CONDUCTOR SCREENING)	-	2000	-
11.1(INSULATION)	-	2000	-
11.2(INSULATION : Thickness of Insulation)	-	5000	-
11.3(INSULATION : Tolerance on Thickness of Insulation)	-	5000	-
11.4(INSULATION : Application of Insulation)	-	2000	-
12.1(INSULATION SCREENING)	-	2000	-
12.2(INSULATION SCREENING)	-	2000	-
12.3(INSULATION SCREENING)	-	2000	-
12.4(INSULATION SCREENING)	-	2000	-
13.1(CORE IDENTIFICATION)	-	2000	-
13.1.1(CORE IDENTIFICATION)	-	2000	-
14.1(LAYING UP OF CORES)	-	2000	-
15.1(INNER SHEATH (COMMON COVERING))	-	2000	-
15.2(INNER SHEATH (COMMON COVERING))	-	2000	-
15.3(INNER SHEATH (COMMON COVERING))	-	2000	-
15.4(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	5000	-
15.4.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	2000	-
16.1.1(ARMOURING : Application)	-	2000	-
16.1.2(ARMOURING : Application)	-	2000	-
16.1.3(ARMOURING : Direction of lay )	-	2000	-
16.1.4(ARMOURING : Application)	-	2000	-
16.2.1(ARMOURING : Type of Armour)	-	2000	-
16.2.2(ARMOURING : Type of Armour)	-	2000	-
16.3(Armouring : Dimensions -Wire Diameter)	-	2000	-
16.3(Armouring : Dimensions -Formed wire )	-	2000	-
16.4(ARMOURING : Joints)	-	2000	-
16.5(ARMOURING : Resistance)	-	2000	-
13.6 a)(ARMOURING: Tensile Strength)	-	2000	-
13.6 b)(ARMOURING: Elongation )	-	2000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	2000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	2000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	2000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	2000	-
13.6 g)(ARMOURING: Resistivity)	-	2000	-
17.1(OUTER SHEATH)	-	2000	-
17.2(OUTER SHEATH : colour )	-	2000	-
17.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	5000	-
17.3.2(Thickness of Outer Sheath : Armoured Cables)	-	5000	-
18.1 a) 1)(Tests on Conductor : Annealing test (for copper))	-	2000	-
18.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	2000	-
18.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	2000	-
18.1 a) 3)(Tests on Conductor : Wrapping test ( for aluminium))	-	2000	-
18.1 a)4)(Tests on conductor : Conductor resistance test - Main conductor )	-	5000	-
18.1 a)4)(Resistance test - Neutral conductor )	-	5000	-
18.1 d) 1)(Phyaical tests for insulation : Tensile Test)	-	5000	-
18.1 d) 1)(Phyaical tests for insulation : Elongation )	-	5000	-
18.1 d) 1)(Physical tests for sheath : Tensile stregth )	-	5000	-
18.1 d) 1)(Physical tests for sheath : Elongation )	-	5000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	5000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	5000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	5000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	5000	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage )	-	5000	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	5000	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage )	-	5000	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	5000	-
18.1 d) 4)(Hot deformation : Insulation )	-	5000	-
18.1 d) 4)(Hot deformation : Sheath )	-	5000	-
18.1 d) 5)( Loss of mass in air oven- Insulation )	-	5000	-
18.1 d) 5)( Loss of mass in air oven- sheath )	-	5000	-
18.1 d) 6)(Heat shock test- Insulation )	-	5000	-
18.1 d) 6)(Heat shock test- sheath )	-	5000	-
18.1 d) 7)(Thermal stability- insulation )	-	5000	-
18.1 d) 7)(Thermal stability- Sheath )	-	5000	-
18.1 d) 8)(Water absorption (gravimetric)(for insulation, where applicable))	-	10000	-
18.1 e)(Insulation resistance test : Volume Resistivity )	-	10000	-
18.1 e)(Insulation resistance test : IR Constant )	-	10000	-
19.2(Partial discharge test)	-	0	-
19.3(Bending test)	-	0	-
19.4(Dielectric power factor test)	-	0	-
19.4(Dielectric power factor test)	-	0	-
19.5(Heating cycle test)	-	0	-
19.6(Impulse withstand test)	-	0	-
19.7(High voltage test)	-	10000	-
19.8(Flammability test)	-	5000	-
19.9(Oxygen Index Test)	-	10000	-
19.10(Flame Retardance Test on Single Cables)	-	5000	-
19.11(Flame Retardance Test on Bunched Cables)	-	10000	-
19.13(Test for Halogen Acid Gas Evolution)	-	10000	-
19.14(Temperature Index)	-	10000	-
18.4(Optional Test : Cold Impact )	-	5000	-
20.1(IDENTIFICATION : Manufacturer's Identification)	-	2000	-
20.2(IDENTIFICATION : Cable Identification)	-	2000	-
20.3(IDENTIFICATION : Cable Code)	-	2000	-
Cl. 18.1 d) 8)(Water absorption Test (Gravimetric))	-	10000	-
Cl.20.1(Manufacturer's Identification)	-	2000	-
Cl.20.2(Cable Identification)	-	2000	-
Cl.20.3(Cable Code)	-	2000	-
Cl.21.1(Packing & Marking)	-	2000	-
Cl.21.2(Packing & Marking)	-	2000	-
Cl.21.2.1(Packing & Marking)	-	2000	-
3.1(CONDUCTOR)	-	2000	-
3.1.1(CONDUCTOR)	-	2000	-
4.1(INSULATION)	-	2000	-
5.1(SCREENING)	-	2000	-
5.1.1(Non-magnetic Metallic Tape for SingleCore Unscreened and Unarmoured Cables)	-	2000	-
6.1(FILLERS AND INNER SHEATH)	-	2000	-
6.2(FILLERS AND INNER SHEATH)	-	2000	-
7.1(ARMOURING)	-	2000	-
7.2(ARMOURING)	-	2000	-
8.1(OUTER SHEATH)	-	2000	-
9.1(CONDUCTOR)	-	2000	-
9.2(CONDUCTOR)	-	2000	-
10.1(CONDUCTOR SCREENING)	-	2000	-
11.1(INSULATION)	-	2000	-
11.2(INSULATION : Thickness of Insulation)	-	5000	-
11.3(INSULATION : Tolerance on Thickness of Insulation)	-	5000	-
11.4(INSULATION : Application of Insulation)	-	2000	-
12.1(INSULATION SCREENING)	-	2000	-
12.2(INSULATION SCREENING)	-	2000	-
12.3(INSULATION SCREENING)	-	2000	-
12.4(INSULATION SCREENING)	-	2000	-
13.1(CORE IDENTIFICATION)	-	2000	-
13.1.1(CORE IDENTIFICATION)	-	2000	-
14.1(LAYING UP OF CORES)	-	2000	-
15.1(INNER SHEATH (COMMON COVERING))	-	2000	-
15.2(INNER SHEATH (COMMON COVERING))	-	2000	-
15.3(INNER SHEATH (COMMON COVERING))	-	2000	-
15.4(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	5000	-
15.4.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	2000	-
16.1.1(ARMOURING : Application)	-	2000	-
16.1.2(ARMOURING : Application)	-	2000	-
16.1.3(ARMOURING : Direction of lay )	-	2000	-
16.1.4(ARMOURING : Application)	-	2000	-
16.2.1(ARMOURING : Type of Armour)	-	2000	-
16.2.2(ARMOURING : Type of Armour)	-	2000	-
16.3(Armouring : Dimensions -Wire Diameter)	-	2000	-
16.3(Armouring : Dimensions -Formed wire )	-	2000	-
16.4(ARMOURING : Joints)	-	2000	-
16.5(ARMOURING : Resistance)	-	2000	-
13.6 a)(ARMOURING: Tensile Strength)	-	2000	-
13.6 b)(ARMOURING: Elongation )	-	2000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	2000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	2000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	2000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	2000	-
13.6 g)(ARMOURING: Resistivity)	-	2000	-
17.1(OUTER SHEATH)	-	2000	-
17.2(OUTER SHEATH : colour )	-	2000	-
17.3.1(Thickness of Outer Sheath : Unarmoured Cables)	-	5000	-
17.3.2(Thickness of Outer Sheath : Armoured Cables)	-	5000	-
18.1 a) 1)(Tests on Conductor : Annealing test (for copper))	-	5000	-
18.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	5000	-
18.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	5000	-
18.1 a) 3)(Tests on Conductor : Wrapping test ( for aluminium))	-	5000	-
18.1 a)4)(Tests on conductor : Conductor resistance test - Main conductor )	-	5000	-
18.1 a)4)(Resistance test - Neutral conductor )	-	5000	-
18.1 d) 1)(Phyaical tests for insulation : Tensile Test)	-	5000	-
18.1 d) 1)(Phyaical tests for insulation : Elongation )	-	5000	-
18.1 d) 1)(Physical tests for sheath : Tensile stregth )	-	5000	-
18.1 d) 1)(Physical tests for sheath : Elongation )	-	5000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	5000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	5000	-
18.1 d) 2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	5000	-
18.1 d) 2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	5000	-
18.1 d) 2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	5000	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage )	-	5000	-
18.1 d) 3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	5000	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage )	-	5000	-
18.1 d) 3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	5000	-
18.1 d) 4)(Hot deformation : Insulation )	-	5000	-
18.1 d) 4)(Hot deformation : Sheath )	-	5000	-
18.1 d) 5)( Loss of mass in air oven- Insulation )	-	5000	-
18.1 d) 5)( Loss of mass in air oven- sheath )	-	5000	-
18.1 d) 6)(Heat shock test- Insulation )	-	5000	-
18.1 d) 6)(Heat shock test- sheath )	-	5000	-
18.1 d) 7)(Thermal stability- insulation )	-	5000	-
18.1 d) 7)(Thermal stability- Sheath )	-	5000	-
18.1 d) 8)(Water absorption (gravimetric)(for insulation, where applicable))	-	10000	-
18.1 e)(Insulation resistance test : Volume Resistivity )	-	10000	-
18.1 e)(Insulation resistance test : IR Constant )	-	10000	-
19.2(Partial discharge test)	-	0	-
19.3(Bending test)	-	0	-
19.4(Dielectric power factor test)	-	0	-
19.4(Dielectric power factor test)	-	0	-
19.5(Heating cycle test)	-	0	-
19.6(Impulse withstand test)	-	0	-
19.7(High voltage test)	-	10000	-
19.8(Flammability test)	-	5000	-
19.9(Oxygen Index Test)	-	10000	-
19.10(Flame Retardance Test on Single Cables)	-	5000	-
19.11(Flame Retardance Test on Bunched Cables)	-	10000	-
19.13(Test for Halogen Acid Gas Evolution)	-	10000	-
19.14(Temperature Index)	-	10000	-
18.4(Optional Test : Cold Impact )	-	5000	-
20.1(IDENTIFICATION : Manufacturer's Identification)	-	2000	-
20.2(IDENTIFICATION : Cable Identification)	-	2000	-
20.3(IDENTIFICATION : Cable Code)	-	2000	-
Cl. 18.1 d) 8)(Water absorption Test (Gravimetric))	-	10000	-
Cl.20.1(Manufacturer's Identification)	-	2000	-
Cl.20.2(Cable Identification)	-	2000	-
Cl.20.3(Cable Code)	-	2000	-
Cl.21.1(Packing & Marking)	-	2000	-
Cl.21.2(Packing & Marking)	-	2000	-
Cl.21.2.1(Packing & Marking)	-	2000	-

07 Sep, 2026

-
Included w.e.f. 04.11.2025 Exclusion: "19.2 (Partial discharge test) 19.3 (Bending test) 19.4 (Dielectric power factor test) 19.5 (Heating cycle test) 19.6 (Impulse withstand test) "

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(S)	-	2000	-
4(P)	-	2000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.00 to 2.24 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2.80 to 3.15 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Hard Core For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Hard Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 For 2.00 to 2.24 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.80 to 3.15 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Soft Core)	-	1000	-
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Soft Core)	-	1000	-
11(a) Size)	-	1000	-
11(b) Construction)	-	1000	-
11(c) tensile designation)	-	1000	-
11(d) lay)	-	1000	-
11(e) coating)	-	1000	-
11(f) length)	-	1000	-
11( g) mass)	-	1000	-
11(h) manufacturer's name or trade mark)	-	1000	-
11(i) lot number along with the order number)	-	1000	-
11(j) BIS Standards Mark)	-	1000	-
5(a) Grade)	-	1000	-
5(b) Tensile Grade)	-	1000	-
6(a) Lay)	-	1000	-
6(b) Construction)	-	1000	-
7(Freedom from defects)	-	1000	-
9(a) Tensile)	-	1000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
11(a) Size)	-	1000	-
11(b) Construction)	-	1000	-
11(c) tensile designation)	-	1000	-
11(d) lay)	-	1000	-
11(e) coating)	-	1000	-
11(f) length)	-	1000	-
11( g) mass)	-	1000	-
11(h) manufacturer's name or trade mark)	-	1000	-
11(i) lot number along with the order number)	-	1000	-
11(j) BIS Standards Mark)	-	1000	-
5(a) Grade)	-	1000	-
5(b) Tensile Grade)	-	1000	-
6(a) Lay)	-	1000	-
6(b) Construction)	-	1000	-
7(Freedom from defects)	-	1000	-
9(a) Tensile)	-	1000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
11(a) Size)	-	1000	-
11(b) Construction)	-	1000	-
11(c) tensile designation)	-	1000	-
11(d) lay)	-	1000	-
11(e) coating)	-	1000	-
11(f) length)	-	1000	-
11( g) mass)	-	1000	-
11(h) manufacturer's name or trade mark)	-	1000	-
11(i) lot number along with the order number)	-	1000	-
11(j) BIS Standards Mark)	-	1000	-
5(a) Grade)	-	1000	-
5(b) Tensile Grade)	-	1000	-
6(a) Lay)	-	1000	-
6(b) Construction)	-	1000	-
7(Freedom from defects)	-	1000	-
9(a) Tensile)	-	1000	-
9(b) Elongation)	-	1000	-
9(c) Galvanizing Test)	-	1000	-
CL 8.2(AVG single wire dia (08))	-	1000	-

07 Sep, 2026

-
Included w.e.f 13.11.2025

IS/IEC 62368 : Part 1 (2023)

Audio Video Information and Communication Technology Equipment - Part 1: Safety Requirements (Second Revision)

75000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General- materials, components)	-	1000	10% discount to BIS
Cl-4.2(Energy source classifications)	-	1000	10% discount to BIS
Cl-4.3(Protection against energy sources)	-	2000	10% discount to BIS
Cl-4.4(Safeguards)	-	1000	10% discount to BIS
Cl-4.5(Explosion)	-	1000	10% discount to BIS
Cl-4.6(Fixing of conductors and conductive parts)	-	2000	10% discount to BIS
Cl-4.7(Equipment for direct insertion into mains socket-outlets)	-	1000	10% discount to BIS
Cl-4.8(Equipment containing coin or button cell batteries)	-	1000	10% discount to BIS
Cl-4.9(Likelihood of fire or shock due to entry of conductive objects)	-	2000	10% discount to BIS
Cl-5.1(General- Electrically-caused injury)	-	2000	10% discount to BIS
Cl-5.2(Classification and limits of electrical energy sources)	-	2000	10% discount to BIS
Cl-5.3(Protection against electrical energy sources)	-	1000	10% discount to BIS
Cl-5.4(Insulation materials and requirements)	-	2000	10% discount to BIS
Cl-5.5(Components as safeguards)	-	1000	10% discount to BIS
Cl-5.6(Protective conductor)	-	2000	10% discount to BIS
Cl-5.7(Prospective touch voltage, touch current and protective conductor current)	-	2000	10% discount to BIS
Cl-5.8(Backfeed safeguard in battery backed up supplies)	-	1000	10% discount to BIS
Cl-6.1(General- Electrically-caused fire)	-	2000	10% discount to BIS
Cl-6.2(Classification of power sources and potential ignition sources)	-	2000	10% discount to BIS
Cl-6.3(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	2000	10% discount to BIS
Cl-6.5(Internal and external wiring)	-	2000	10% discount to BIS
Cl-7.1(General- Injury caused by hazardous substances)	-	1000	10% discount to BIS
Cl-7.2(Reduction of exposure to hazardous substances)	-	1000	10% discount to BIS
Cl-7.3(Ozone exposure)	-	1000	10% discount to BIS
Cl-7.4(Use of personal safeguards or personal protective equipment (PPE)	-	1000	10% discount to BIS
Cl-7.5(Use of instructional safeguards and instructions)	-	1000	10% discount to BIS
Cl-8.1(General- Mechanically-caused injury)	-	2000	10% discount to BIS
Cl-8.2(Mechanical energy source classifications)	-	2000	10% discount to BIS
Cl-8.3(Safeguards against mechanical energy sources)	-	1000	10% discount to BIS
Cl-8.4(Safeguards against parts with sharp edges and corners)	-	1000	10% discount to BIS
Cl-8.5(Safeguards against moving parts)	-	2000	10% discount to BIS
Cl-8.6(Stability of equipment)	-	2000	10% discount to BIS
Cl-8.7(Equipment mounted to a wall, ceiling or other structure)	-	2000	10% discount to BIS
Cl-8.8(Handle strength)	-	1000	10% discount to BIS
Cl-8.9(Wheels or casters attachment requirements)	-	1000	10% discount to BIS
Cl-8.10(Carts, stands, and similar carriers)	-	1000	10% discount to BIS
Cl-9.1(General-Thermal burn injury)	-	1000	10% discount to BIS
Cl-8.11(Mounting means for slide-rail mounted equipment (SRME))	-	1000	10% discount to BIS
Cl-9.2(Thermal energy source classifications)	-	1000	10% discount to BIS
Cl-9.3(Touch temperature limits)	-	2000	10% discount to BIS
Cl-9.4(Safeguards against thermal energy sources)	-	1000	10% discount to BIS
Cl-9.5(Requirements for safeguards)	-	1000	10% discount to BIS
Cl-9.6(Requirements for wireless power transmitters)	-	2000	10% discount to BIS
Cl-10.1(General-Radiation)	-	0	-
Cl-10.2(Radiation energy source classifications)	-	0	-
Cl-10.3(Safeguards against laser radiation)	-	0	-
Cl-10.4("Safeguards against optical radiation from lamps and lamp systems (including LED types)")	-	0	-
Cl-10.5(Safeguards against X-radiation)	-	0	-
Cl-10.6(Safeguards against acoustic energy sources)	-	0	-
Annex A(Examples of equipment within the scope of this document)	-	1000	10% discount to BIS
Annex B(General- Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	2000	10% discount to BIS
Annex B-2(Normal operating conditions)	-	2000	10% discount to BIS
Annex B-3(Simulated abnormal operating conditions)	-	2000	10% discount to BIS
Annex B-4(Simulated single fault conditions)	-	2000	10% discount to BIS
Annex C-1(Protection of materials in equipment from UV radiation)	-	0	-
Annex C-2(UV light conditioning test)	-	0	-
Annex D-1(Impulse test generators)	-	2000	10% discount to BIS
Annex D-2(Antenna interface test generator)	-	2000	10% discount to BIS
Annex D-3(Electronic pulse generator)	-	2000	10% discount to BIS
Annex E-1(Electrical energy source classification for audio signals)	-	2000	10% discount to BIS
Annex E-2(Audio signals used during test)	-	2000	10% discount to BIS
Annex E-3(Operating conditions of equipment containing an audio amplifier)	-	1000	10% discount to BIS
Annex F-1(General-Equipment markings, instructions, and instructional safeguards)	-	1000	10% discount to BIS
Annex F-2(Letter symbols and graphical symbols)	-	1000	10% discount to BIS
Annex F-3(Equipment markings)	-	1000	10% discount to BIS
Annex F-4(Instructions)	-	1000	10% discount to BIS
Annex F-5(Instructional safeguards)	-	1000	10% discount to BIS
Annex G-1(Switches)	-	1000	10% discount to BIS
Annex G-2(Relays)	-	1000	10% discount to BIS
Annex G-3(Protective devices)	-	1000	10% discount to BIS
Annex G-4(Connectors)	-	1000	10% discount to BIS
Annex G-5(Wound components)	-	1000	10% discount to BIS
Annex G-6(Wire insulation)	-	1000	10% discount to BIS
Annex G-7(Mains power supply cords and interconnection cables)	-	1000	10% discount to BIS
Annex G-8(Varistors)	-	1000	10% discount to BIS
Annex G-9(Integrated circuit (IC) current limiters)	-	1000	10% discount to BIS
Annex G-12(Optocouplers)	-	1000	10% discount to BIS
Annex G-13(Printed boards)	-	1000	10% discount to BIS
Annex G-14(Coatings on component terminals)	-	1000	10% discount to BIS
Annex G-16(IC that includes a capacitor discharge function (ICX))	-	1000	10% discount to BIS
Annex H-1(General- Criteria for telephone ringing signals)	-	1000	10% discount to BIS
Annex H-2(Method A)	-	1000	10% discount to BIS
Annex H-3(Method B)	-	1000	10% discount to BIS
Annex I(Overvoltage categories (see IEC 60364-4-44))	-	2000	10% discount to BIS
Annex J-1(General-Insulated winding wires for use without interleaved insulation)	-	1000	10% discount to BIS
Annex J-2(Type tests)	-	1000	10% discount to BIS
Annex J-3(Testing during manufacturing)	-	1000	10% discount to BIS
Annex K-1(General- Safety interlocks)	-	1000	10% discount to BIS
Annex K-2(Components of the safety interlock safeguard mechanism)	-	1000	10% discount to BIS
Annex K-3(Inadvertent change of operating mode)	-	1000	10% discount to BIS
Annex K-4(Interlock safeguard override)	-	1000	10% discount to BIS
Annex K-5(Fail-safe)	-	1000	10% discount to BIS
Annex K-6(Mechanically operated safety interlocks)	-	1000	10% discount to BIS
Annex K-7(Interlock circuit isolation)	-	1000	10% discount to BIS
Annex L-1(General requirements)	-	1000	10% discount to BIS
Annex L-2(Permanently connected equipment)	-	1000	10% discount to BIS
Annex L-3()	-	1000	10% discount to BIS
Annex L-4(Single-phase equipment)	-	1000	10% discount to BIS
Annex L-5(Three-phase equipment)	-	1000	10% discount to BIS
Annex L-6(Switches as disconnect devices)	-	1000	10% discount to BIS
Annex L-7(Plugs as disconnect devices)	-	1000	10% discount to BIS
Annex L-8(Multiple power sources)	-	1000	10% discount to BIS
Annex L-9(Compliance criteria)	-	1000	10% discount to BIS
Annex M-1(General requirements)	-	1000	10% discount to BIS
Annex M-2(Safety of batteries and their cells)	-	1000	10% discount to BIS
Annex M-3(Protection circuits for batteries provided within the equipment)	-	1000	10% discount to BIS
Annex M-4(Additional safeguards for equipment containing a secondary lithium battery)	-	1000	10% discount to BIS
Annex M-5(Risk of burn due to short-circuit during carrying)	-	1000	10% discount to BIS
Annex M-6(Safeguards against short-circuits)	-	1000	10% discount to BIS
Annex M-7(Risk of explosion from lead acid and NiCd batteries)	-	1000	10% discount to BIS
Annex M-8("Protection against internal ignition from external spark sources of rechargeable batteries with aqueous electrolyte")	-	1000	10% discount to BIS
Annex M-9(Preventing electrolyte spillage)	-	1000	10% discount to BIS
Annex M-10(Instructions to prevent reasonably foreseeable misuse)	-	1000	10% discount to BIS
Annex O(Measurement of creepage distances and clearances)	-	2000	10% discount to BIS
Annex P-1(General-Safeguards against conductive objects)	-	1000	10% discount to BIS
Annex P-2(Safeguards against entry or consequences of entry of a foreign object)	-	1000	10% discount to BIS
Annex P-3(Safeguards against spillage of internal liquids)	-	1000	10% discount to BIS
Annex P-4(Metallized coatings and adhesives securing parts)	-	1000	10% discount to BIS
Annex Q-1(Limited power source)	-	2000	10% discount to BIS
Annex Q-2(Test for external circuits – paired conductor cable)	-	2000	10% discount to BIS
Annex R(Limited short-circuit test)	-	2000	10% discount to BIS
Annex S-1(Flammability test for fire enclosure and fire barrier materials of equipment where the steady state power does not exceed 4 000 W)	-	1000	10% discount to BIS
Annex S-2(Flammability test for fire enclosure and fire barrier integrity)	-	2000	10% discount to BIS
Annex S-3(Flammability tests for the bottom of a fire enclosure)	-	2000	10% discount to BIS
Annex S-4(Flammability classification of materials)	-	1000	10% discount to BIS
Annex S-5(Flammability test for fire enclosure materials of equipment with a steady state power exceeding 4 000 W)	-	1000	10% discount to BIS
Annex S-6(Grille covering material, cloth, and reticulated foam)	-	1000	10% discount to BIS
Annex T-1(General-Mechanical strength tests)	-	1000	10% discount to BIS
Annex T-2(Steady force test, 10 N)	-	1000	10% discount to BIS
Annex T-3(Steady force test, 30 N)	-	1000	10% discount to BIS
Annex T-4(Steady force test, 100 N)	-	1000	10% discount to BIS
Annex T-5(Steady force test, 250 N)	-	1000	10% discount to BIS
Annex T-6(Enclosure impact test)	-	1000	10% discount to BIS
Annex T-7(Drop test)	-	2000	10% discount to BIS
Annex T-8(Stress relief test)	-	2000	10% discount to BIS
Annex T-9(Glass impact test)	-	1000	10% discount to BIS
Annex T-10(Glass fragmentation test)	-	1000	10% discount to BIS
Annex T-11(Test for telescoping or rod antennas)	-	1000	10% discount to BIS
Annex U("Mechanical strength of CRTs and protection against the effects of implosion")	-	0	-
Annex V-1(Accessible parts of equipment)	-	2000	10% discount to BIS
Annex V-2(Accessible part criterion)	-	2000	10% discount to BIS
Annex W(Comparison of terms introduced in this document)	-	1000	10% discount to BIS
Annex X("Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420 V peak (300 V RMS)")	-	2000	10% discount to BIS
Annex Y-1(General- Construction requirements for outdoor enclosures)	-	1000	10% discount to BIS
Annex Y-2(Resistance to UV radiation)	-	1000	10% discount to BIS
Annex Y-3(Resistance to corrosion)	-	1000	10% discount to BIS
Annex Y-4(Gaskets)	-	1000	10% discount to BIS
Annex Y-5(Protection of equipment within an outdoor enclosure)	-	1000	10% discount to BIS
Annex Y-6(Mechanical strength of enclosures)	-	1000	10% discount to BIS
Cl-6.4(Safeguards against fire under single fault conditions)	-	2000	10% discount to BIS
Cl-4.10(Components requirements)	-	1000	10% discount to BIS
Annex G-10(Resistors)	-	1000	10% discount to BIS
Annex G-11(Capacitors and RC units)	-	1000	10% discount to BIS
Annex G-15(Pressurized liquid filled components or LFC assemblies)	-	1000	10% discount to BIS
Annex N(Electrochemical potentials (V))	-	1000	10% discount to BIS
Cl-4.1(General- materials, components)	-	-	-
Cl-4.2(Energy source classifications)	-	-	-
Cl-4.3(Protection against energy sources)	-	-	-
Cl-4.4(Safeguards)	-	-	-
Cl-4.5(Explosion)	-	-	-
Cl-4.6(Fixing of conductors and conductive parts)	-	-	-
Cl-4.7(Equipment for direct insertion into mains socket-outlets)	-	-	-
Cl-4.8(Equipment containing coin or button cell batteries)	-	-	-
Cl-4.9(Likelihood of fire or shock due to entry of conductive objects)	-	-	-
Cl-5.1(General- Electrically-caused injury)	-	-	-
Cl-5.2(Classification and limits of electrical energy sources)	-	-	-
Cl-5.3(Protection against electrical energy sources)	-	-	-
Cl-5.4(Insulation materials and requirements)	-	-	-
Cl-5.5(Components as safeguards)	-	-	-
Cl-5.6(Protective conductor)	-	-	-
Cl-5.7(Prospective touch voltage, touch current and protective conductor current)	-	-	-
Cl-5.8(Backfeed safeguard in battery backed up supplies)	-	-	-
Cl-6.1(General- Electrically-caused fire)	-	-	-
Cl-6.2(Classification of power sources and potential ignition sources)	-	-	-
Cl-6.3(Safeguards against fire under normal operating conditions and abnormal operating conditions)	-	-	-
Cl-6.5(Internal and external wiring)	-	-	-
Cl-7.1(General- Injury caused by hazardous substances)	-	-	-
Cl-7.2(Reduction of exposure to hazardous substances)	-	-	-
Cl-7.3(Ozone exposure)	-	-	-
Cl-7.4(Use of personal safeguards or personal protective equipment (PPE)	-	-	-
Cl-7.5(Use of instructional safeguards and instructions)	-	-	-
Cl-8.1(General- Mechanically-caused injury)	-	-	-
Cl-8.2(Mechanical energy source classifications)	-	-	-
Cl-8.3(Safeguards against mechanical energy sources)	-	-	-
Cl-8.4(Safeguards against parts with sharp edges and corners)	-	-	-
Cl-8.5(Safeguards against moving parts)	-	-	-
Cl-8.6(Stability of equipment)	-	-	-
Cl-8.7(Equipment mounted to a wall, ceiling or other structure)	-	-	-
Cl-8.8(Handle strength)	-	-	-
Cl-8.9(Wheels or casters attachment requirements)	-	-	-
Cl-8.10(Carts, stands, and similar carriers)	-	-	-
Cl-9.1(General-Thermal burn injury)	-	-	-
Cl-8.11(Mounting means for slide-rail mounted equipment (SRME))	-	-	-
Cl-9.2(Thermal energy source classifications)	-	-	-
Cl-9.3(Touch temperature limits)	-	-	-
Cl-9.4(Safeguards against thermal energy sources)	-	-	-
Cl-9.5(Requirements for safeguards)	-	-	-
Cl-9.6(Requirements for wireless power transmitters)	-	-	-
Annex A(Examples of equipment within the scope of this document)	-	-	-
Annex B(General- Normal operating condition tests, abnormal operating condition tests and single fault condition tests)	-	-	-
Annex B-2(Normal operating conditions)	-	-	-
Annex B-3(Simulated abnormal operating conditions)	-	-	-
Annex B-4(Simulated single fault conditions)	-	-	-
Annex D-1(Impulse test generators)	-	-	-
Annex E-1(Electrical energy source classification for audio signals)	-	-	-
Annex E-2(Audio signals used during test)	-	-	-
Annex E-3(Operating conditions of equipment containing an audio amplifier)	-	-	-
Annex F-1(General-Equipment markings, instructions, and instructional safeguards)	-	-	-
Annex F-2(Letter symbols and graphical symbols)	-	-	-
Annex F-3(Equipment markings)	-	-	-
Annex F-4(Instructions)	-	-	-
Annex F-5(Instructional safeguards)	-	-	-
Annex G-1(Switches)	-	-	-
Annex G-2(Relays)	-	-	-
Annex G-3(Protective devices)	-	-	-
Annex G-4(Connectors)	-	-	-
Annex G-5(Wound components)	-	-	-
Annex G-6(Wire insulation)	-	-	-
Annex G-7(Mains power supply cords and interconnection cables)	-	-	-
Annex G-8(Varistors)	-	-	-
Annex G-9(Integrated circuit (IC) current limiters)	-	-	-
Annex G-12(Optocouplers)	-	-	-
Annex G-13(Printed boards)	-	-	-
Annex G-14(Coatings on component terminals)	-	-	-
Annex G-16(IC that includes a capacitor discharge function (ICX))	-	-	-
Annex H-1(General- Criteria for telephone ringing signals)	-	-	-
Annex H-2(Method A)	-	-	-
Annex H-3(Method B)	-	-	-
Annex I(Overvoltage categories (see IEC 60364-4-44))	-	-	-
Annex J-1(General-Insulated winding wires for use without interleaved insulation)	-	-	-
Annex J-2(Type tests)	-	-	-
Annex J-3(Testing during manufacturing)	-	-	-
Annex K-1(General- Safety interlocks)	-	-	-
Annex K-2(Components of the safety interlock safeguard mechanism)	-	-	-
Annex K-3(Inadvertent change of operating mode)	-	-	-
Annex K-4(Interlock safeguard override)	-	-	-
Annex K-5(Fail-safe)	-	-	-
Annex K-6(Mechanically operated safety interlocks)	-	-	-
Annex K-7(Interlock circuit isolation)	-	-	-
Annex L-1(General requirements)	-	-	-
Annex L-2(Permanently connected equipment)	-	-	-
Annex L-3()	-	-	-
Annex L-4(Single-phase equipment)	-	-	-
Annex L-5(Three-phase equipment)	-	-	-
Annex L-6(Switches as disconnect devices)	-	-	-
Annex L-7(Plugs as disconnect devices)	-	-	-
Annex L-8(Multiple power sources)	-	-	-
Annex L-9(Compliance criteria)	-	-	-
Annex M-1(General requirements)	-	-	-
Annex M-2(Safety of batteries and their cells)	-	-	-
Annex M-3(Protection circuits for batteries provided within the equipment)	-	-	-
Annex M-4(Additional safeguards for equipment containing a secondary lithium battery)	-	-	-
Annex M-5(Risk of burn due to short-circuit during carrying)	-	-	-
Annex M-6(Safeguards against short-circuits)	-	-	-
Annex M-9(Preventing electrolyte spillage)	-	-	-
Annex M-10(Instructions to prevent reasonably foreseeable misuse)	-	-	-
Annex O(Measurement of creepage distances and clearances)	-	-	-
Annex P-1(General-Safeguards against conductive objects)	-	-	-
Annex P-2(Safeguards against entry or consequences of entry of a foreign object)	-	-	-
Annex P-3(Safeguards against spillage of internal liquids)	-	-	-
Annex P-4(Metallized coatings and adhesives securing parts)	-	-	-
Annex Q-1(Limited power source)	-	-	-
Annex Q-2(Test for external circuits – paired conductor cable)	-	-	-
Annex R(Limited short-circuit test)	-	-	-
Annex S-1(Flammability test for fire enclosure and fire barrier materials of equipment where the steady state power does not exceed 4 000 W)	-	-	-
Annex S-2(Flammability test for fire enclosure and fire barrier integrity)	-	-	-
Annex S-3(Flammability tests for the bottom of a fire enclosure)	-	-	-
Annex S-4(Flammability classification of materials)	-	-	-
Annex S-5(Flammability test for fire enclosure materials of equipment with a steady state power exceeding 4 000 W)	-	-	-
Annex S-6(Grille covering material, cloth, and reticulated foam)	-	-	-
Annex T-1(General-Mechanical strength tests)	-	-	-
Annex T-2(Steady force test, 10 N)	-	-	-
Annex T-3(Steady force test, 30 N)	-	-	-
Annex T-4(Steady force test, 100 N)	-	-	-
Annex T-5(Steady force test, 250 N)	-	-	-
Annex T-6(Enclosure impact test)	-	-	-
Annex T-7(Drop test)	-	-	-
Annex T-8(Stress relief test)	-	-	-
Annex T-9(Glass impact test)	-	-	-
Annex T-10(Glass fragmentation test)	-	-	-
Annex T-11(Test for telescoping or rod antennas)	-	-	-
Annex V-1(Accessible parts of equipment)	-	-	-
Annex V-2(Accessible part criterion)	-	-	-
Annex W(Comparison of terms introduced in this document)	-	-	-
Annex X("Alternative method for determining clearances for insulation in circuits connected to an AC mains not exceeding 420 V peak (300 V RMS)")	-	-	-
Annex Y-1(General- Construction requirements for outdoor enclosures)	-	-	-
Annex Y-2(Resistance to UV radiation)	-	-	-
Annex Y-3(Resistance to corrosion)	-	-	-
Annex Y-5(Protection of equipment within an outdoor enclosure)	-	-	-
Annex Y-6(Mechanical strength of enclosures)	-	-	-
Cl-6.4(Safeguards against fire under single fault conditions)	-	-	-
Cl-4.10(Components requirements)	-	-	-
Annex G-10(Resistors)	-	-	-
Annex G-11(Capacitors and RC units)	-	-	-
Annex N(Electrochemical potentials (V))	-	-	-
Annex D-2(Antenna interface test generator)	-	-	-
Annex D-3(Electronic pulse generator)	-	-	-
Annex G-15(Pressurized liquid filled components or LFC assemblies)	-	-	-
Annex M-7(Risk of explosion from lead acid and NiCd batteries)	-	-	-
Annex M-8("Protection against internal ignition from external spark sources of rechargeable batteries with aqueous electrolyte")	-	-	-
Annex Y-4(Gaskets)	-	-	-

07 Sep, 2026

-
Included w.e.f 23.09.2025 Exclusion: Cl-10.1 (General-Radiation), Cl-10.2 (Radiation energy source classifications), Cl-10.3 (Safeguards against laser radiation), , Cl-10.4 ("Safeguards against optical radiation from lamps and lamp systems (including LED types)"), Cl-10.5 (Safeguards against X-radiation), Cl-10.6 (Safeguards against acoustic energy sources) , Annex C-1 (Protection of materials in equipment from UV radiation) , Annex C-2 (UV light conditioning test), Annex U ("Mechanical strength of CRTs and protection against the effects of implosion")

IS 7098 : Part 2 (2011)

Crosslinked polyethylene insulated thermoplastic sheathed cables - Specification: Part 2 for working voltages from 3.3 kV up to and including 33 kV (Second Revision)

Complete for Unscreened Cable rated Up to and Including 3.3/3.3 kV.

125000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(CONDUCTOR)	-	1000	Rs.125000/- for Rated Voltage Up to 3.3/3.3 kV (Only 3.3/3.3 Grade)
4.1.1(CONDUCTOR)	-	1000	-
5(INSULATION)	-	1000	-
6(SCREENING)	-	0	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	0	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	1000	-
7(FILLERS AND INNER SHEATH)	-	1000	-
8.1(ARMOURING)	-	1000	-
8.2(ARMOURING)	-	1000	-
9(OUTER SHEATH )	-	1000	-
10.1(CONDUCTOR)	-	1000	-
10.2(CONDUCTOR)	-	1000	-
11(CONDUCTOR SCREENING)	-	0	-
12.1(INSULATION)	-	1000	-
12.2(INSULATION : Thickness of Insulation)	-	2000	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	2000	-
12.4(Eccentricity and Ovality)	-	2000	-
12.5(INSULATION : Application of Insulation)	-	1000	-
13.1(INSULATION SCREENING)	-	0	-
13.2(INSULATION SCREENING)	-	0	-
13.3(INSULATION SCREENING)	-	0	-
13.4(INSULATION SCREENING)	-	0	-
14.1(CORE IDENTIFICATION)	-	1000	-
14.1.1(CORE IDENTIFICATION)	-	1000	-
15.1(LAVING UP OF CORES)	-	1000	-
16.1(INNER SHEATH (COMMON COVERING))	-	1000	-
16.2(INNER SHEATH (COMMON COVERING))	-	1000	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	1000	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	1000	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	1000	-
17.1(ARMOURING : Application )	-	1000	-
17.1.1(ARMOURING )	-	1000	-
17.1.2(ARMOURING )	-	1000	-
17.1.3(ARMOURING )	-	1000	-
17.2(ARMOURING : Type of armour )	-	1000	-
17.2.1(ARMOURING : Type of armour )	-	1000	-
17.2(ARMOURING : Coverage )	-	1000	-
17.3(ARMOURING : Dimension )	-	1000	-
17.4(ARMOURING : Joints)	-	1000	-
16.4(ARMOURING : Resistance)	-	2000	-
18.1(OUTER SHEATH)	-	1000	-
18.2(OUTER SHEATH: Colour)	-	1000	-
18.3(Thicknes of outer sheath : average )	-	2000	-
18.3(Thicknes of outer sheath : minimum )	-	2000	-
19.1 i) a)(Annealing test (for copper))	-	2000	-
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	2000	-
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	2000	-
19.1 i) c)(Wrapping test ( for aluminium))	-	2000	-
19.1 i) d)(Resistance test - Main conductor )	-	2000	-
19.1 i) d)(Resistance test - Neutral conductor )	-	2000	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	2000	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	2000	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	5000	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	5000	-
19.1 iii) c)(Degree of cross linking )	-	5000	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	2000	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	2000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	2000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	2000	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	10000	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	0	-
19.1 v) b)(Volume resistivity)	-	5000	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	5000	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	5000	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	2000	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	2000	-
19.1 vi) d)(Sheath : Hot deformation)	-	2000	-
19.1 vi) e)(Loss of massIn air oven)	-	5000	-
19.1 vi) f)(Sheath : Heat shock test)	-	2000	-
19.1 vi) g)(Sheath : Thermalstability)	-	2000	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	2000	-
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	5000	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	5000	-
20.2(Partial discharge test)	-	0	-
20.3(Bending test)	-	0	-
20.4(Dielectric power factor test : As a function of voltage)	-	0	-
20.4(Dielectric power factor test : As a function of temperature)	-	0	-
20.5(Heating Cycle Test)	-	0	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	0	-
20.7(High voltage test)	-	5000	-
20.8(Flammability test)	-	5000	-
20.1(Oxygen Index Test)	-	5000	-
20.11(Flame Retardance Test on Single Cables)	-	2000	-
20.12(Flame Retardance Test on Bunched Cables)	-	10000	-
20.13(Test for Halogen Acid Gas Evolution)	-	10000	-
20.14( Test for Smoke Density)	-	5000	-
20.15(Temperature Index)	-	5000	-
21.1(IDENTIFICATION : Manufacturer's Identification)	-	1000	-
21.2(IDENTIFICATION : Cable Identification)	-	1000	-
21.3(IDENTIFICATION : Cable Code)	-	1000	-
20.3 (a)(Partial discharge test (Bending test))	-	0	-
20.5 (a)(PD test (heating cycle test))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	0	-
Cl-20.6(Impulse Withstand Test (Rated voltage, kv 33/33 Impulse voltage , kv 250))	-	0	-
Cl. 8(Conductor)	-	1000	-
Cl. 8(Conductor)	-	1000	-
Cl. 8(Conductor)	-	1000	-
Cl.8 & 17(Armouring)	-	1000	-
Cl. 17.5(Armouring : Resistance of Armour,)	-	2000	-
Cl.8 & 17(Armouring : Tensile Strength)	-	2000	-
Cl.8 & 17(Armouring : Elongation)	-	2000	-
Cl.8 & 17(Armouring : Torsion Test (For Round Steel Wire Only))	-	2000	-
Cl.8 & 17(Armouring: Winding Test ( For formed steel wire only))	-	2000	-
Cl.8 & 17(Armouring : Application)	-	1000	-
Cl.8 & 17(Armouring : Uniformity of Zinc Coating)	-	2000	-
Cl.8 & 17(Armouring: Mass of Zinc Coating)	-	2000	-
Cl.8 & 17(Armouring : Resistivity Test)	-	2000	-
Cl.8 & 17(Armouring: Cold Impact Test (For outer Sheath))	-	2000	-
Cl. 13.5.1 and Table 7(Armouring: Resistance Test for Armouring (Other than Mining Cables))	-	2000	-
4.1(CONDUCTOR)	-	1000	-
4.1.1(CONDUCTOR)	-	1000	-
5(INSULATION)	-	1000	-
6(SCREENING)	-	0	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	0	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	5000	-
7(FILLERS AND INNER SHEATH)	-	1000	-
8.1(ARMOURING)	-	1000	-
8.2(ARMOURING)	-	1000	-
9(OUTER SHEATH )	-	1000	-
10.1(CONDUCTOR)	-	1000	-
10.2(CONDUCTOR)	-	1000	-
11(CONDUCTOR SCREENING)	-	0	-
12.1(INSULATION)	-	1000	-
12.2(INSULATION : Thickness of Insulation)	-	2000	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	2000	-
12.4(Eccentricity and Ovality)	-	2000	-
12.5(INSULATION : Application of Insulation)	-	1000	-
13.1(INSULATION SCREENING)	-	0	-
13.2(INSULATION SCREENING)	-	0	-
13.3(INSULATION SCREENING)	-	0	-
13.4(INSULATION SCREENING)	-	0	-
14.1(CORE IDENTIFICATION)	-	1000	-
14.1.1(CORE IDENTIFICATION)	-	1000	-
15.1(LAVING UP OF CORES)	-	1000	-
16.1(INNER SHEATH (COMMON COVERING))	-	1000	-
16.2(INNER SHEATH (COMMON COVERING))	-	1000	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	1000	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	1000	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	2000	-
17.1(ARMOURING : Application )	-	1000	-
17.1.1(ARMOURING )	-	1000	-
17.1.2(ARMOURING )	-	1000	-
17.1.3(ARMOURING )	-	1000	-
17.2(ARMOURING : Type of armour )	-	1000	-
17.2.1(ARMOURING : Type of armour )	-	1000	-
17.2(ARMOURING : Coverage )	-	2000	-
17.3(ARMOURING : Dimension )	-	2000	-
17.4(ARMOURING : Joints)	-	2000	-
16.4(ARMOURING : Resistance)	-	2000	-
18.1(OUTER SHEATH)	-	1000	-
18.2(OUTER SHEATH: Colour)	-	1000	-
18.3(Thicknes of outer sheath : average )	-	2000	-
18.3(Thicknes of outer sheath : minimum )	-	2000	-
19.1 i) a)(Annealing test (for copper))	-	2000	-
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	2000	-
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	2000	-
19.1 i) c)(Wrapping test ( for aluminium))	-	2000	-
19.1 i) d)(Resistance test - Main conductor )	-	5000	-
19.1 i) d)(Resistance test - Neutral conductor )	-	5000	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	2000	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	2000	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	5000	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	5000	-
19.1 iii) c)(Degree of cross linking )	-	5000	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	2000	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	2000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	2000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	2000	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	10000	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	0	-
19.1 v) b)(Volume resistivity)	-	5000	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	2000	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	2000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	5000	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	2000	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	2000	-
19.1 vi) d)(Sheath : Hot deformation)	-	2000	-
19.1 vi) e)(Loss of massIn air oven)	-	5000	-
19.1 vi) f)(Sheath : Heat shock test)	-	2000	-
19.1 vi) g)(Sheath : Thermalstability)	-	5000	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	5000	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	2000	-
20.2(Partial discharge test)	-	0	-
20.3(Bending test)	-	0	-
20.4(Dielectric power factor test : As a function of voltage)	-	0	-
20.4(Dielectric power factor test : As a function of temperature)	-	0	-
20.5(Heating Cycle Test)	-	0	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	0	-
20.7(High voltage test)	-	5000	-
20.8(Flammability test)	-	2000	-
20.1(Oxygen Index Test)	-	5000	-
20.11(Flame Retardance Test on Single Cables)	-	5000	-
20.12(Flame Retardance Test on Bunched Cables)	-	10000	-
20.13(Test for Halogen Acid Gas Evolution)	-	5000	-
20.14( Test for Smoke Density)	-	5000	-
20.15(Temperature Index)	-	5000	-
21.1(IDENTIFICATION : Manufacturer's Identification)	-	2000	-
21.2(IDENTIFICATION : Cable Identification)	-	2000	-
21.3(IDENTIFICATION : Cable Code)	-	2000	-
20.3 (a)(Partial discharge test (Bending test))	-	0	-
20.5 (a)(PD test (heating cycle test))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	0	-
Cl-20.6(Impulse Withstand Test (Rated voltage, kv 33/33 Impulse voltage , kv 250))	-	0	-
Cl. 8(Conductor)	-	2000	-
Cl. 8(Conductor)	-	2000	-
Cl. 8(Conductor)	-	2000	-
Cl.8 & 17(Armouring)	-	2000	-
Cl. 17.5(Armouring : Resistance of Armour,)	-	2000	-
Cl.8 & 17(Armouring : Tensile Strength)	-	2000	-
Cl.8 & 17(Armouring : Elongation)	-	2000	-
Cl.8 & 17(Armouring : Torsion Test (For Round Steel Wire Only))	-	2000	-
Cl.8 & 17(Armouring: Winding Test ( For formed steel wire only))	-	2000	-
Cl.8 & 17(Armouring : Application)	-	2000	-
Cl.8 & 17(Armouring : Uniformity of Zinc Coating)	-	2000	-
Cl.8 & 17(Armouring: Mass of Zinc Coating)	-	2000	-
Cl.8 & 17(Armouring : Resistivity Test)	-	2000	-
Cl.8 & 17(Armouring: Cold Impact Test (For outer Sheath))	-	2000	-
Cl. 13.5.1 and Table 7(Armouring: Resistance Test for Armouring (Other than Mining Cables))	-	2000	-
4.1(CONDUCTOR)	-	1000	-
4.1.1(CONDUCTOR)	-	1000	-
5(INSULATION)	-	1000	-
6(SCREENING)	-	0	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	0	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	1000	-
7(FILLERS AND INNER SHEATH)	-	1000	-
8.1(ARMOURING)	-	1000	-
8.2(ARMOURING)	-	1000	-
9(OUTER SHEATH )	-	1000	-
10.1(CONDUCTOR)	-	1000	-
10.2(CONDUCTOR)	-	1000	-
11(CONDUCTOR SCREENING)	-	0	-
12.1(INSULATION)	-	1000	-
12.2(INSULATION : Thickness of Insulation)	-	2000	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	2000	-
12.4(Eccentricity and Ovality)	-	2000	-
12.5(INSULATION : Application of Insulation)	-	1000	-
13.1(INSULATION SCREENING)	-	0	-
13.2(INSULATION SCREENING)	-	0	-
13.3(INSULATION SCREENING)	-	0	-
13.4(INSULATION SCREENING)	-	0	-
14.1(CORE IDENTIFICATION)	-	1000	-
14.1.1(CORE IDENTIFICATION)	-	1000	-
15.1(LAVING UP OF CORES)	-	1000	-
16.1(INNER SHEATH (COMMON COVERING))	-	1000	-
16.2(INNER SHEATH (COMMON COVERING))	-	1000	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	1000	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	2000	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	2000	-
17.1(ARMOURING : Application )	-	1000	-
17.1.1(ARMOURING )	-	2000	-
17.1.2(ARMOURING )	-	2000	-
17.1.3(ARMOURING )	-	2000	-
17.2(ARMOURING : Type of armour )	-	2000	-
17.2.1(ARMOURING : Type of armour )	-	2000	-
17.2(ARMOURING : Coverage )	-	2000	-
17.3(ARMOURING : Dimension )	-	2000	-
17.4(ARMOURING : Joints)	-	2000	-
16.4(ARMOURING : Resistance)	-	2000	-
18.1(OUTER SHEATH)	-	1000	-
18.2(OUTER SHEATH: Colour)	-	1000	-
18.3(Thicknes of outer sheath : average )	-	2000	-
18.3(Thicknes of outer sheath : minimum )	-	2000	-
19.1 i) a)(Annealing test (for copper))	-	2000	-
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	2000	-
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	2000	-
19.1 i) c)(Wrapping test ( for aluminium))	-	2000	-
19.1 i) d)(Resistance test - Main conductor )	-	2000	-
19.1 i) d)(Resistance test - Neutral conductor )	-	2000	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	2000	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	2000	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	5000	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	5000	-
19.1 iii) c)(Degree of cross linking )	-	2000	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	5000	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	5000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	2000	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	2000	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	5000	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	0	-
19.1 v) b)(Volume resistivity)	-	5000	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	2000	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	2000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	5000	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	5000	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	2000	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	2000	-
19.1 vi) d)(Sheath : Hot deformation)	-	2000	-
19.1 vi) e)(Loss of massIn air oven)	-	5000	-
19.1 vi) f)(Sheath : Heat shock test)	-	2000	-
19.1 vi) g)(Sheath : Thermalstability)	-	5000	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	5000	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	5000	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	5000	-
20.2(Partial discharge test)	-	0	-
20.3(Bending test)	-	0	-
20.4(Dielectric power factor test : As a function of voltage)	-	0	-
20.4(Dielectric power factor test : As a function of temperature)	-	0	-
20.5(Heating Cycle Test)	-	0	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	0	-
20.7(High voltage test)	-	5000	-
20.8(Flammability test)	-	5000	-
20.1(Oxygen Index Test)	-	5000	-
20.11(Flame Retardance Test on Single Cables)	-	5000	-
20.12(Flame Retardance Test on Bunched Cables)	-	10000	-
20.13(Test for Halogen Acid Gas Evolution)	-	5000	-
20.14( Test for Smoke Density)	-	5000	-
20.15(Temperature Index)	-	5000	-
21.1(IDENTIFICATION : Manufacturer's Identification)	-	2000	-
21.2(IDENTIFICATION : Cable Identification)	-	2000	-
21.3(IDENTIFICATION : Cable Code)	-	2000	-
20.3 (a)(Partial discharge test (Bending test))	-	0	-
20.5 (a)(PD test (heating cycle test))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	0	-
Cl-20.6(Impulse Withstand Test (Rated voltage, kv 33/33 Impulse voltage , kv 250))	-	0	-
Cl. 8(Conductor)	-	1000	-
Cl. 8(Conductor)	-	1000	-
Cl. 8(Conductor)	-	1000	-
Cl.8 & 17(Armouring)	-	1000	-
Cl. 17.5(Armouring : Resistance of Armour,)	-	2000	-
Cl.8 & 17(Armouring : Tensile Strength)	-	2000	-
Cl.8 & 17(Armouring : Elongation)	-	2000	-
Cl.8 & 17(Armouring : Torsion Test (For Round Steel Wire Only))	-	2000	-
Cl.8 & 17(Armouring: Winding Test ( For formed steel wire only))	-	2000	-
Cl.8 & 17(Armouring : Application)	-	1000	-
Cl.8 & 17(Armouring : Uniformity of Zinc Coating)	-	2000	-
Cl.8 & 17(Armouring: Mass of Zinc Coating)	-	2000	-
Cl.8 & 17(Armouring : Resistivity Test)	-	2000	-
Cl.8 & 17(Armouring: Cold Impact Test (For outer Sheath))	-	2000	-
Cl. 13.5.1 and Table 7(Armouring: Resistance Test for Armouring (Other than Mining Cables))	-	2000	-
4.1(CONDUCTOR)	-	0	-
4.1.1(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
6(SCREENING)	-	0	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	0	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	0	-
7(FILLERS AND INNER SHEATH)	-	0	-
8.1(ARMOURING)	-	0	-
8.2(ARMOURING)	-	0	-
9(OUTER SHEATH )	-	0	-
10.1(CONDUCTOR)	-	0	-
10.2(CONDUCTOR)	-	0	-
11(CONDUCTOR SCREENING)	-	0	-
12.1(INSULATION)	-	0	-
12.2(INSULATION : Thickness of Insulation)	-	0	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	0	-
12.4(Eccentricity and Ovality)	-	0	-
12.5(INSULATION : Application of Insulation)	-	0	-
13.1(INSULATION SCREENING)	-	0	-
13.2(INSULATION SCREENING)	-	0	-
13.3(INSULATION SCREENING)	-	0	-
13.4(INSULATION SCREENING)	-	0	-
14.1(CORE IDENTIFICATION)	-	0	-
14.1.1(CORE IDENTIFICATION)	-	0	-
15.1(LAVING UP OF CORES)	-	0	-
16.1(INNER SHEATH (COMMON COVERING))	-	0	-
16.2(INNER SHEATH (COMMON COVERING))	-	0	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	0	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	0	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	0	-
17.1(ARMOURING : Application )	-	0	-
17.1.1(ARMOURING )	-	0	-
17.1.2(ARMOURING )	-	0	-
17.1.3(ARMOURING )	-	0	-
17.2(ARMOURING : Type of armour )	-	0	-
17.2.1(ARMOURING : Type of armour )	-	0	-
17.2(ARMOURING : Coverage )	-	0	-
17.3(ARMOURING : Dimension )	-	0	-
17.4(ARMOURING : Joints)	-	0	-
16.4(ARMOURING : Resistance)	-	0	-
18.1(OUTER SHEATH)	-	0	-
18.2(OUTER SHEATH: Colour)	-	0	-
18.3(Thicknes of outer sheath : average )	-	0	-
18.3(Thicknes of outer sheath : minimum )	-	0	-
19.1 i) a)(Annealing test (for copper))	-	0	-
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	0	-
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	0	-
19.1 i) c)(Wrapping test ( for aluminium))	-	0	-
19.1 i) d)(Resistance test - Main conductor )	-	0	-
19.1 i) d)(Resistance test - Neutral conductor )	-	0	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	0	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	0	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
19.1 iii) c)(Degree of cross linking )	-	0	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	0	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	0	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	0	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	0	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	0	-
19.1 v) b)(Volume resistivity)	-	0	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	0	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	0	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	0	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	0	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
19.1 vi) d)(Sheath : Hot deformation)	-	0	-
19.1 vi) e)(Loss of massIn air oven)	-	0	-
19.1 vi) f)(Sheath : Heat shock test)	-	0	-
19.1 vi) g)(Sheath : Thermalstability)	-	0	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	0	-
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	0	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	0	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	0	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	0	-
20.2(Partial discharge test)	-	0	-
20.3(Bending test)	-	0	-
20.4(Dielectric power factor test : As a function of voltage)	-	0	-
20.4(Dielectric power factor test : As a function of temperature)	-	0	-
20.5(Heating Cycle Test)	-	0	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	0	-
20.7(High voltage test)	-	0	-
20.8(Flammability test)	-	0	-
20.1(Oxygen Index Test)	-	0	-
20.11(Flame Retardance Test on Single Cables)	-	0	-
20.12(Flame Retardance Test on Bunched Cables)	-	0	-
20.13(Test for Halogen Acid Gas Evolution)	-	0	-
20.14( Test for Smoke Density)	-	0	-
20.15(Temperature Index)	-	0	-
21.1(IDENTIFICATION : Manufacturer's Identification)	-	0	-
21.2(IDENTIFICATION : Cable Identification)	-	0	-
21.3(IDENTIFICATION : Cable Code)	-	0	-
20.3 (a)(Partial discharge test (Bending test))	-	0	-
20.5 (a)(PD test (heating cycle test))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	0	-
Cl-20.6(Impulse Withstand Test (Rated voltage, kv 33/33 Impulse voltage , kv 250))	-	0	-
Cl. 8(Conductor)	-	0	-
Cl. 8(Conductor)	-	0	-
Cl. 8(Conductor)	-	0	-
Cl.8 & 17(Armouring)	-	0	-
Cl. 17.5(Armouring : Resistance of Armour,)	-	0	-
Cl.8 & 17(Armouring : Tensile Strength)	-	0	-
Cl.8 & 17(Armouring : Elongation)	-	0	-
Cl.8 & 17(Armouring : Torsion Test (For Round Steel Wire Only))	-	0	-
Cl.8 & 17(Armouring: Winding Test ( For formed steel wire only))	-	0	-
Cl.8 & 17(Armouring : Application)	-	0	-
Cl.8 & 17(Armouring : Uniformity of Zinc Coating)	-	0	-
Cl.8 & 17(Armouring: Mass of Zinc Coating)	-	0	-
Cl.8 & 17(Armouring : Resistivity Test)	-	0	-
Cl.8 & 17(Armouring: Cold Impact Test (For outer Sheath))	-	0	-
Cl. 13.5.1 and Table 7(Armouring: Resistance Test for Armouring (Other than Mining Cables))	-	0	-
4.1(CONDUCTOR)	-	0	-
4.1.1(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
6(SCREENING)	-	0	-
6.1.1(SCREENING : - Non-metallic — Semiconducting Compound)	-	0	-
6.1.2(SCREENING : - Non-magnetic Metallic Tape for Single Core Unscreened and Unarmoured Cables)	-	0	-
7(FILLERS AND INNER SHEATH)	-	0	-
8.1(ARMOURING)	-	0	-
8.2(ARMOURING)	-	0	-
9(OUTER SHEATH )	-	0	-
10.1(CONDUCTOR)	-	0	-
10.2(CONDUCTOR)	-	0	-
11(CONDUCTOR SCREENING)	-	0	-
12.1(INSULATION)	-	0	-
12.2(INSULATION : Thickness of Insulation)	-	0	-
12.3(INSULATION : Tolerance on Thickness of Insulation)	-	0	-
12.4(Eccentricity and Ovality)	-	0	-
12.5(INSULATION : Application of Insulation)	-	0	-
13.1(INSULATION SCREENING)	-	0	-
13.2(INSULATION SCREENING)	-	0	-
13.3(INSULATION SCREENING)	-	0	-
13.4(INSULATION SCREENING)	-	0	-
14.1(CORE IDENTIFICATION)	-	0	-
14.1.1(CORE IDENTIFICATION)	-	0	-
15.1(LAVING UP OF CORES)	-	0	-
16.1(INNER SHEATH (COMMON COVERING))	-	0	-
16.2(INNER SHEATH (COMMON COVERING))	-	0	-
16.2.1(INNER SHEATH (COMMON COVERING))	-	0	-
16.3(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	0	-
16.3.1(INNER SHEATH (COMMON COVERING) : Thickness of Inner Sheath)	-	0	-
17.1(ARMOURING : Application )	-	0	-
17.1.1(ARMOURING )	-	0	-
17.1.2(ARMOURING )	-	0	-
17.1.3(ARMOURING )	-	0	-
17.2(ARMOURING : Type of armour )	-	0	-
17.2.1(ARMOURING : Type of armour )	-	0	-
17.2(ARMOURING : Coverage )	-	0	-
17.3(ARMOURING : Dimension )	-	0	-
17.4(ARMOURING : Joints)	-	0	-
16.4(ARMOURING : Resistance)	-	0	-
18.1(OUTER SHEATH)	-	0	-
18.2(OUTER SHEATH: Colour)	-	0	-
18.3(Thicknes of outer sheath : average )	-	0	-
18.3(Thicknes of outer sheath : minimum )	-	0	-
19.1 i) a)(Annealing test (for copper))	-	0	-
19.1 i) b)(Tensile test (for aluminium) - Before stranding )	-	0	-
19.1 i) b)(Tensile test (for aluminium) - After stranding )	-	0	-
19.1 i) c)(Wrapping test ( for aluminium))	-	0	-
19.1 i) d)(Resistance test - Main conductor )	-	0	-
19.1 i) d)(Resistance test - Neutral conductor )	-	0	-
19.1 iii) a)(Phyaical tests for insulation : Tensile Test)	-	0	-
19.1 iii) a)(Phyaical tests for insulation : Elongation )	-	0	-
19.1 iii) b)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	0	-
19.1 iii) b)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	0	-
19.1 iii) c)(Degree of cross linking )	-	0	-
19.1 iii) d)(Phyaical tests for insulation : Hot set )	-	0	-
19.1 iii) d)(Phyaical tests for insulation : Permanent set )	-	0	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage )	-	0	-
19.1 iii) e)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	0	-
19.1 iii) f)(Insulation: Waterabsorption(gravimetric))	-	0	-
19.1 v) a)(Test for strippability of semiconducting strippable insulation screen (when applicable))	-	0	-
19.1 v) b)(Volume resistivity)	-	0	-
19.1 vi) a)(Physical tests for outer sheath : Tensile stregth )	-	0	-
19.1 vi) a)(Physical tests for outer sheath : Elongation )	-	0	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	0	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	0	-
19.1 vi) b)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	0	-
19.1 vi) b)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	0	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage )	-	0	-
19.1 vi) c)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	0	-
19.1 vi) d)(Sheath : Hot deformation)	-	0	-
19.1 vi) e)(Loss of massIn air oven)	-	0	-
19.1 vi) f)(Sheath : Heat shock test)	-	0	-
19.1 vi) g)(Sheath : Thermalstability)	-	0	-
19.1 vi) h)(Carbon black content of polythene sheath )	-	0	-
19.1 vii)(Thermal ageing test for complete cable - Tensile stregth )	-	0	-
19.1 vii)(Thermal ageing test for complete cable- Elogation )	-	0	-
19.1 vii)(Thermal ageing test for complete cable- Resistivity )	-	0	-
19.1 xi)(Insulation resistance test : volume resistivity )	-	0	-
20.2(Partial discharge test)	-	0	-
20.3(Bending test)	-	0	-
20.4(Dielectric power factor test : As a function of voltage)	-	0	-
20.4(Dielectric power factor test : As a function of temperature)	-	0	-
20.5(Heating Cycle Test)	-	0	-
20.6(Impulse withstand test (Rated voltage, kV 3.8/6.6 Impulse voltage, kV 60))	-	0	-
20.7(High voltage test)	-	0	-
20.8(Flammability test)	-	0	-
20.1(Oxygen Index Test)	-	0	-
20.11(Flame Retardance Test on Single Cables)	-	0	-
20.12(Flame Retardance Test on Bunched Cables)	-	0	-
20.13(Test for Halogen Acid Gas Evolution)	-	0	-
20.14( Test for Smoke Density)	-	0	-
20.15(Temperature Index)	-	0	-
21.1(IDENTIFICATION : Manufacturer's Identification)	-	0	-
21.2(IDENTIFICATION : Cable Identification)	-	0	-
21.3(IDENTIFICATION : Cable Code)	-	0	-
20.3 (a)(Partial discharge test (Bending test))	-	0	-
20.5 (a)(PD test (heating cycle test))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 6.35/11 Impulse voltage, kV 75))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 11/11 Impulse voltage, kV 95))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 12.7/22 Impulse voltage, kV 125))	-	0	-
20.6(Impulse Withstand Test (Rated voltage, kV 19/33 Impulse voltage, kV 170))	-	0	-
Cl-20.6(Impulse Withstand Test (Rated voltage, kv 33/33 Impulse voltage , kv 250))	-	0	-
Cl. 8(Conductor)	-	0	-
Cl. 8(Conductor)	-	0	-
Cl. 8(Conductor)	-	0	-
Cl.8 & 17(Armouring)	-	0	-
Cl. 17.5(Armouring : Resistance of Armour,)	-	0	-
Cl.8 & 17(Armouring : Tensile Strength)	-	0	-
Cl.8 & 17(Armouring : Elongation)	-	0	-
Cl.8 & 17(Armouring : Torsion Test (For Round Steel Wire Only))	-	0	-
Cl.8 & 17(Armouring: Winding Test ( For formed steel wire only))	-	0	-
Cl.8 & 17(Armouring : Application)	-	0	-
Cl.8 & 17(Armouring : Uniformity of Zinc Coating)	-	0	-
Cl.8 & 17(Armouring: Mass of Zinc Coating)	-	0	-
Cl.8 & 17(Armouring : Resistivity Test)	-	0	-
Cl.8 & 17(Armouring: Cold Impact Test (For outer Sheath))	-	0	-
Cl. 13.5.1 and Table 7(Armouring: Resistance Test for Armouring (Other than Mining Cables))	-	0	-
Cl-20.16 (Amendment No-2)(Longitudinal Water Penetration Test)	-	20000	-

07 Sep, 2026

-
Included w.e.f 04.02.2026

IS 16246 (2015)

Elastomer insulated cables with limited circuit integrity when affected by fire - Specification

85000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1( Cables for Fixed Installation)	-	1000	-
Cl.5( INSULATION)	-	1000	-
Cl. 6.1( Glass Tape)	-	1000	-
Cl 6.2( Polyethylene Teraphthalate (PETP) or Polypropylene base Tape)	-	1000	-
Cl 6.4( Fire Barrier Tape)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 7(CENTRE AND FILLERS)	-	1000	-
Cl 8( ARMOUR)	-	1000	-
Cl 9.1( Inner Sheath)	-	1000	-
Cl 9.2( Outer Sheath)	-	1000	-
Cl 10.1( CONDUCTORS)	-	1000	-
Cl 10.2( CONDUCTORS)	-	1000	-
Cl 11.1( INSULATION)	-	1000	-
Cl 11.2(Thickness of Insulation IS 10810 : Part 6)	-	2000	-
Cl 12( CORE IDENTIFICATION)	-	1000	-
Cl 13( LAYING UP OF CORES)	-	1000	-
Cl 14.2( Thickness of Inner Sheath IS 10810 : Part 6)	-	2000	-
Cl 15.1( ARMOURING)	-	1000	-
Cl 15.3.1( Type of Armour)	-	1000	-
Cl 15.3.2( Type of Armour)	-	1000	-
Cl 15.3.3( ARMOURING)	-	1000	-
Cl 15.3.3( ARMOURING)	-	1000	-
Cl 15.4.1( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 15.4.2( ARMOURING)	-	1000	-
Cl 16.2( OUTER SHEATH)	-	1000	-
Cl 16.3( Thickness of Outer Sheath - Avg IS 10810 : Part 6)	-	2000	-
Cl 16.3( Thickness of Outer Sheath - Minimum IS 10810 : Part 6)	-	2000	-
Cl 17.2(Annealing test (for copper) IS 10810 : Part 1)	-	2000	-
Cl 17.2(Conductor resistance test IS 10810 : Part 5)	-	2000	-
Cl 17.1(Persulphate test (tinned copper conductor) IS 10810 : Part 4)	-	5000	-
Cl 17.2(Tensile strength before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(elongation at break before ageing on insulation IS 10810 : Part 7)	-	2000	-
Cl 17.2(Tensile strength after Ageing in air bomb IS 10810 : Part 56)	-	5000	-
Cl 17.2(Elongation after Ageing in air bomb IS 10810 : Part 56)	-	5000	-
Cl 17.2(Tensile strength variation)	-	5000	-
Cl 17.2(Elongation Variation)	-	5000	-
Cl 17.2(Hot set elongation on insulation IS 10810 : Part 30)	-	2000	-
Cl 17.2(Permanent elongation (set) on insulation IS 10810 : Part 30)	-	2000	-
Cl 17.1(Tensile strength before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(elongation at break before ageing on sheath IS 10810 : Part 7)	-	2000	-
Cl 17.1(Hot set elongation test on sheath IS 10810 : Part 30)	-	2000	-
Cl 17.1(Permanent elongation (set) test on sheath IS 10810 : Part 30)	-	2000	-
Cl 17.1(Oxygen index test on sheath IS 10810 : Part 58)	-	5000	-
Cl 17.1(Temperature index test on sheath IS 10810 : Part 64)	-	5000	-
Cl 17.1(Acid gas generation on sheath IS 10810 : Part 39)	-	5000	-
Cl 17.2(Insulation resistance test IS 10810 : Part 43)	-	2000	-
Cl 17.1(Water absorption test (for insulation) IS 10810 : Part 28)	-	10000	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2000	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	2000	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	25000	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	25000	-
Cl 18.4.1( Flame Retardence Test on Single Cable IS 10810 : Part 61)	-	10000	-
Cl 18.4.2(Flame Retardence Test on Bunched Cables IS 10810 : Part 63)	-	10000	-
Cl 19.1( Manufacturer’s Identification)	-	1000	-
Cl 19.2( Voltage Identification)	-	1000	-
Cl 19.3( Cable Identification)	-	1000	-
Cl 19.4( Cable Code)	-	1000	-

07 Sep, 2026

-
Included w.e.f.18.08.2025

IS 2465 (1984)

Specification for cables for motor vehicles (Second Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Insulation)	-	1000	-
7.3(Insulation)	-	1000	-
8(Core Identification)	-	1000	-
9(Laying up of cores)	-	1000	-
10.1.1(Sheathing )	-	1000	-
10.2(Sheathing )	-	1000	-
3 & 6(Flexibility class)	-	1000	-
3 & 6(Construction)	-	1000	-
3 & 6(Diameter of wire(mm))	-	1000	-
3 & 6(Annealing test)	-	1000	-
3 & 6(Persulphate Test)	-	1000	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	2000	-
7.2, 10.3, 11(Dimensions & thickness )	-	2000	-
7.2, 10.3, 11(Dimensions & thickness )	-	2000	-
7.2, 10.3, 11(Overall Dimension (mm))	-	2000	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	2000	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	2000	-
4.2 & 12.1, (f), 1(Tensile Strength at break (N/mm²))	-	2000	-
4.2 & 12.1, (e), 1(elongation test at break)	-	2000	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	2000	-
4.2 & 12.1, (f), 2(Ageing in air oven)	-	3000	-
4.2 & 12.1, (f), 3(Ageing in oxygen bomb)	-	3000	-
4.2 & 12.1, (e), 2(After Ageing in air oven)	-	3000	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Insulation)	-	3000	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Sheath)	-	3000	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Insulation)	-	2000	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Sheath)	-	2000	-
4.2 & 12.1, (e), 5(Heat Shock Test of Insulation)	-	2000	-
4.2 & 12.1, (e), 5(Heat Shock Test of Sheath)	-	2000	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Insulation)	-	2000	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Sheath)	-	2000	-
14(High Voltage Test)	-	2000	-
15(SPARK TEST FOR SINGLE CORE GENERAL WIRING CABLES)	-	2000	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	3000	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	10000	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	3000	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	3000	-
19.2(EFFECT OF OIL ON IGNITION CABLES)	-	3000	-
20.3(EFFECT OF LUBRICATING OIL)	-	3000	-
20.3(EFFECT OF LUBRICATING OIL)	-	3000	-
20.3(EFFECT OF BRAKE FLUID)	-	3000	-
20.3(EFFECT OF BRAKE FLUID)	-	3000	-
20.3(EFFECT OF DIESEL)	-	3000	-
20.3(EFFECT OF DIESEL)	-	3000	-
20.3(Increase in average diameter %)	-	3000	-
20.3(Wrapping test)	-	2000	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	3000	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	3000	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	3000	-
22.1(FLAMMABILITY TEST)	-	2000	-
22.1(FLAMMABILITY TEST)	-	2000	-
23.1(Manufacturer's Identification)	-	1000	-
23.1(Manufacturer's Identification)	-	1000	-
24.1(PACKING AND MARKING)	-	1000	-
24.2(PACKING AND MARKING)	-	1000	-
24.2.1(PACKING AND MARKING)	-	1000	-
12.1.b(Persulphate test (when applicable))	-	2000	-
6.1, 12.3, 12.1.c(Conductor Resistance)	-	2000	-
12.1.e4(Hot deformation)	-	2000	-
12.1.e5(Heat Shock)	-	2000	-
CL.12.1 (e) 2(Tensile Strength After Ageing)	-	3000	-
CL.12.1 (e) 2(Elongation After Ageing)	-	3000	-
CL.12.1 (e) 2(Tensile Strength Variation)	-	3000	-
CL.12.1 (e) 2(Elongation Variation)	-	3000	-
CL.12.1 (e) 2(Elongation Variation)	-	3000	-
Cl.12 (e) 5(Heat shock test)	-	2000	-
Cl.12 (e) 4(Hot Deformation Test)	-	2000	-
Cl.12 (e) 6(Shrinkage Test)	-	2000	-
Cl.12 (e) 6(Shrinkage Test (Cracks Observed))	-	2000	-
Cl. 12.1 (e) 3(Loss of Mass Insulation)	-	3000	-
7.1(Insulation)	-	1000	-
7.3(Insulation)	-	1000	-
8(Core Identification)	-	1000	-
9(Laying up of cores)	-	1000	-
10.1.1(Sheathing )	-	1000	-
10.2(Sheathing )	-	1000	-
3 & 6(Flexibility class)	-	1000	-
3 & 6(Construction)	-	1000	-
3 & 6(Diameter of wire(mm))	-	1000	-
3 & 6(Annealing test)	-	1000	-
3 & 6(Persulphate Test)	-	2000	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	2000	-
7.2, 10.3, 11(Dimensions & thickness )	-	2000	-
7.2, 10.3, 11(Dimensions & thickness )	-	2000	-
7.2, 10.3, 11(Overall Dimension (mm))	-	2000	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	2000	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	2000	-
4.2 & 12.1, (f), 1(Tensile Strength at break (N/mm²))	-	2000	-
4.2 & 12.1, (e), 1(elongation test at break)	-	2000	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	2000	-
4.2 & 12.1, (f), 2(Ageing in air oven)	-	2000	-
4.2 & 12.1, (f), 3(Ageing in oxygen bomb)	-	3000	-
4.2 & 12.1, (e), 2(After Ageing in air oven)	-	2000	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Insulation)	-	2000	-
4.2 & 12.1, (e), 3(Loss of mass test (mg/cm²) of Sheath)	-	2000	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Insulation)	-	2000	-
4.2 & 12.1, (e), 4(Hot deformation test (%) of Sheath)	-	2000	-
4.2 & 12.1, (e), 5(Heat Shock Test of Insulation)	-	1000	-
4.2 & 12.1, (e), 5(Heat Shock Test of Sheath)	-	1000	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Insulation)	-	1000	-
4.2 & 12.1, (e), 6(Shrinkage Test (%) of Sheath)	-	1000	-
14(High Voltage Test)	-	2000	-
15(SPARK TEST FOR SINGLE CORE GENERAL WIRING CABLES)	-	2000	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	3000	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	5000	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	5000	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	5000	-
19.2(EFFECT OF OIL ON IGNITION CABLES)	-	3000	-
20.3(EFFECT OF LUBRICATING OIL)	-	3000	-
20.3(EFFECT OF LUBRICATING OIL)	-	3000	-
20.3(EFFECT OF BRAKE FLUID)	-	3000	-
20.3(EFFECT OF BRAKE FLUID)	-	3000	-
20.3(EFFECT OF DIESEL)	-	2000	-
20.3(EFFECT OF DIESEL)	-	2000	-
20.3(Increase in average diameter %)	-	2000	-
20.3(Wrapping test)	-	2000	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	2000	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	2000	-
21.2(EFFECT OF COOLING ON FLEXIBILITY)	-	2000	-
22.1(FLAMMABILITY TEST)	-	2000	-
22.1(FLAMMABILITY TEST)	-	2000	-
23.1(Manufacturer's Identification)	-	1000	-
23.1(Manufacturer's Identification)	-	1000	-
24.1(PACKING AND MARKING)	-	1000	-
24.2(PACKING AND MARKING)	-	1000	-
24.2.1(PACKING AND MARKING)	-	1000	-
12.1.b(Persulphate test (when applicable))	-	2000	-
6.1, 12.3, 12.1.c(Conductor Resistance)	-	2000	-
12.1.e4(Hot deformation)	-	2000	-
12.1.e5(Heat Shock)	-	1000	-
CL.12.1 (e) 2(Tensile Strength After Ageing)	-	3000	-
CL.12.1 (e) 2(Elongation After Ageing)	-	3000	-
CL.12.1 (e) 2(Tensile Strength Variation)	-	3000	-
CL.12.1 (e) 2(Elongation Variation)	-	3000	-
CL.12.1 (e) 2(Elongation Variation)	-	3000	-
Cl.12 (e) 5(Heat shock test)	-	1000	-
Cl.12 (e) 4(Hot Deformation Test)	-	2000	-
Cl.12 (e) 6(Shrinkage Test)	-	1000	-
Cl.12 (e) 6(Shrinkage Test (Cracks Observed))	-	1000	-
Cl. 12.1 (e) 3(Loss of Mass Insulation)	-	3000	-

07 Sep, 2026

-
Included w.e.f. 29.09.2025

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

140000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	1000	Rs. 20000/- [Up to 100 Sq.mm], Rs. 110000/- [150 & 200 Sq.mm] Rs. 120000/- [400 & 560 Sq.mm] Rs. 140000/- [420 & 520 Sq.mm]
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	1000	-
10 (elec)(Stranding)	-	1000	-
10 (elec)(Stranding)	-	1000	-
10 (elec)(Stranding)	-	1000	-
10 (mech)(Stranding)	-	1000	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	1000	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	1000	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	1000	-
13.7.2 (chem)(Mass of Zinc coating)	-	1000	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.9 (elec)(Surface condition test)	-	20000	-
13.10 (elec)(Ultimate breaking load)	-	20000	-
13.11 (elec)(Stress-strain test)	-	80000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	1000	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	1000	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	1000	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
10 (elec)(Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	1000	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	1000	-
4.1(Resistivity)	-	2000	-
4.2(Density)	-	2000	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	2000	-
4.4(Coefficient of Linear Expansion)	-	2000	-
5.1(Density)	-	2000	-
5.2(Coefficient of Linear Expansion)	-	2000	-
14.2(a), 8.2.1(Sizes)	-	2000	-
7(FREEDOM FROM DEFECTS)	-	2000	-
6.2(zinc Purity)	-	2000	-
9(Joint in wires)	-	2000	-
6.1.1(Aluminum wires shall conform to IS 5484)	-	2000	-
6.1.2(The mechanical properties of wire shall comply with the requirements given in Table 2)	-	1000	-
6.2(It shall conform to and satisfy all the requirements of IS 209)	-	1000	-
8.2.2(Calculated resistance)	-	1000	-
Cl-9.2.5(Welded joint strength)	-	2000	-

07 Sep, 2026

-
-

IS 14494 (2019)

Elastomer insulated flexible cables for use in mines - Specification (First Revision)

55000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(CONDUCTOR)	-	1000	Rs. 55,000/- [ 1.1 kV ] Rs. 75,000/- [ 3.3 kV ] Rs. 125,000/- [ 3.8/6.6 kV ]
5(INSULATION)	-	1000	-
5.1(Power Cores)	-	1000	-
5.2(Pilot and Earth Cores)	-	1000	-
6(SEMI-CONDUCTING COMPOUND)	-	1000	-
7.1(TAPE : Proofed Tape)	-	1000	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	1000	-
7.3(TAPE )	-	1000	-
8(CENTRE)	-	1000	-
9.1(FILLERS)	-	1000	-
9.2(FILLERS)	-	1000	-
10(CRADLE SEPARATOR)	-	1000	-
11.1(ARMOUR)	-	1000	-
11.2(ARMOUR)	-	1000	-
11.2 a)(ARMOURING: Tensile Strength)	-	2000	-
11.2 b)(ARMOURING: Elongation )	-	2000	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	2000	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	2000	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	2000	-
12.1(SHEATH : Inner Sheath)	-	1000	-
12.2(SHEATH : Outer Sheath)	-	1000	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	1000	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	1000	-
14.1(CONSTRUCTION : CONDUCTOR)	-	1000	-
14.2(CONSTRUCTION : CONDUCTOR)	-	1000	-
14.3(CONSTRUCTION : CONDUCTOR)	-	1000	-
14.4(CONSTRUCTION : CONDUCTOR)	-	1000	-
15(CONDUCTOR SCREENING)	-	1000	-
16.1(INSULATION)	-	1000	-
16.2(INSULATION : Thickness of Insulation)	-	2000	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	2000	-
16.4(INSULATION : Application of Insulation)	-	1000	-
16.5(INSULATION)	-	1000	-
17.1(INSULATION SCREEN)	-	1000	-
17.2(INSULATION SCREEN)	-	1000	-
17.3(INSULATION SCREEN)	-	1000	-
17.4(INSULATION SCREEN)	-	1000	-
18(PROTECTIVE SCREEN)	-	1000	-
19(CONDUCTANCE OF SCREEN)	-	1000	-
19.1(Individual Core Screen)	-	1000	-
19.2(Collective Screen)	-	1000	-
20.1(CORE IDENTIFICATION)	-	1000	-
20.2(Colour Scheme for Identification)	-	1000	-
20.3(Scheme for Identification by Numbering)	-	1000	-
21.1(LAYING UP OF CORES)	-	1000	-
21.2(LAYING UP OF CORES)	-	1000	-
21.3(LAYING UP OF CORES)	-	1000	-
21.4(LAYING UP OF CORES)	-	1000	-
22.1(INNER SHEATH)	-	1000	-
22.2(Thickness of Inner Sheath)	-	2000	-
22.3(INNER SHEATH)	-	1000	-
23.1(ARMOURING)	-	1000	-
23.2(ARMOURING)	-	1000	-
23.3(ARMOURING)	-	1000	-
23.4(ARMOURING)	-	1000	-
24.1(OUTER SHEATH)	-	1000	-
24.2(Thickness of Outer Sheath)	-	2000	-
24.3(Tolerance on Thickness of Outer Sheath)	-	2000	-
24.4(OUTER SHEATH)	-	1000	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	2000	-
27.2(Bending test followed by partial discharge test;)	-	50000	-
27.4(Dielectric power factor test)	-	50000	-
27.5(Heating cycle test followed by partial discharge test;)	-	50000	-
27.6(Impulse voltage test; and)	-	50000	-
26.3(Special Provisions)	-	5000	-
27.8(Flammability Test)	-	5000	-
27.9(Water Absorption Test)	-	10000	-
28(IDENTIFICATION)	-	1000	-
29.1(PACKING AND MARKING)	-	1000	-
29.2(PACKING AND MARKING)	-	1000	-
30(BIS CERTIFICATION MARKING)	-	1000	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	5000	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	30000	-
Table 33(j), Cl. No. 27.4(Dielectric Power Factor (as a function of Voltage))	-	50000	-
Table 33(h), Cl. No. 27.2(Partial discharge test)	-	50000	-
Table 33(f)(Insulation resistance)	-	10000	-
Table 33(e)(Tear resistance on sheath)	-	5000	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	10000	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	10000	-
Table 33(e)(Permanent set on Sheath)	-	5000	-
Table 33(e)(Hot set on Sheath)	-	5000	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	10000	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	10000	-
Table 33(e)(Elongation at break on Sheath)	-	10000	-
Table 33(e)(Tensile strength on Sheath)	-	10000	-
Table 33(d)(Ozone resistance on Insulation)	-	10000	-
Table 33(d)(Permanent set on Insulation)	-	5000	-
Table 33(d)(Hot set on Insulation)	-	5000	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	10000	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	10000	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	10000	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	10000	-
Table 33(d)(Elongation at break on Insulation)	-	10000	-
Table 33(d)(Tensile strength on Insulation)	-	10000	-
Table 33(c)(Resistivity of steel wire)	-	5000	-
Table 33(b)(Diameter of armour wire)	-	2000	-
Table 4(Copper purity test)	-	5000	-
Table 33(a)(Conductor resistance test)	-	5000	-
Table 33(a)(Annealing test)	-	2000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath ( After ageing in air bomb)	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Oil resistance test ))	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath)	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	5000	-
[ Cl.12.2 & Table 3 IS:6380-1984](Physical tests on Outer Sheath (Hot set test))	-	5000	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	10000	-
[ Table 2 of IS:6380-1984](Insulation resistance constant)	-	10000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Outer Sheath ( Without ageing))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air oven:))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on insulation (After ageing in air bomb ))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	5000	-
[ Cl.5 & Table 2 of IS:6380-1984](Physical tests on Insulation (Hot set test))	-	5000	-
[ Cl.4 & 14](Conductor)	-	5000	-
[ Cl.4 & 14](Conductor)	-	5000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[ Cl.4 & 14](Conductor)	-	1000	-
[Cl.14.4](Conductor)	-	1000	-
Cl. 27.7(High voltage test for 4 hours)	-	30000	-

07 Sep, 2026

-
"1 Table 33®, Annex E (Electric tset on semi-conducting screen) Electrical Test Test Facility Not Available 2 27.2 (Bending test followed by partial discharge test;) Partial Discharge test Test Facility Not Available 3 27.4 (Dielectric power factor test) Dielectric Power Factor Test Test Facility Not Available 4 27.5 (Heating cycle test followed by partial discharge test;) Heating cycle test followed by partial discharge test Test Facility Not Available 5 27.6 (Impulse voltage test; and) Impulse Voltage test Test Facility Not Available 6 Table 33(j), Cl. No. 27.4 (Dielectric Power Factor (as a function of Voltage)) Dielectric Power Factor test Test Facility Not Available 7 Table 33(h), Cl. No. 27.2 (Partial discharge test) Partial discharge test Test Facility Not Available"

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

135000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	2000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	2000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	2000	-
IS 191:2007 & IS 440(Copper purity test)	-	5000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	2000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	5000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	5000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	2000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	5000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	5000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	2000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	2000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	3000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	3000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	2000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	2000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	2000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	5000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	30000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	40000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	2000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	15000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	15000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	10000	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	10000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	5000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	2000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	5000	-
IS 191:2007 & IS 440(Copper purity test)	-	10000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	2000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	5000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	5000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	5000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	10000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	10000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	5000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	5000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	5000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	10000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	20000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	10000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	5000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	5000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	5000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	5000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	10000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	20000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	50000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	5000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	20000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	20000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	10000	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	10000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	10000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	10000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	10000	-
IS 191:2007 & IS 440(Copper purity test)	-	20000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	10000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	10000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	10000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	10000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	10000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	10000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	10000	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	10000	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	10000	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	10000	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	10000	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	10000	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	10000	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	10000	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	10000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	10000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	10000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	10000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	10000	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	10000	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	10000	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	10000	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	10000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	10000	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	10000	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	10000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	10000	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	10000	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	10000	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	10000	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	10000	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	10000	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	1000	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	10000	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	10000	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	10000	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	10000	-

07 Sep, 2026

-
Included w.e.f.18.08.2025

IS 17293 (2020)

Electric Cables for Photovoltaic Systems for Rated Voltage 1 500 V d.c.

1020000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	2000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	2000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	2000	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	5000	-
IS 191 : 2007, IS 440(Copper purity test)	-	5000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	10000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	2000	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	5000	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	10000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	2000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	3000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	3000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	10000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	10000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	10000	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	2000	-
Annex - B of IS 17293:2020(Compatibility test)	-	10000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	2000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	2000	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	2000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	10000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	10000	-
Annex - B of IS 17293:2020(Compatibility test)	-	10000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	2000	-
Annex - E of IS 17293 : 2020(UV resistance)	-	100000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	10000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	10000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	10000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
11.2.2(Spark Test)	-	10000	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	100000	-
11.2.5(Surface Resistance of Sheath)	-	10000	-
11.3.1(Sheath Colour)	-	2000	-
11.3.2(Sheath Marking)	-	2000	-
11.3.3(Overall Diameters and Ovality)	-	2000	-
Annex J(Assessment of Halogens)	-	10000	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	5000	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	5000	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	5000	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	700000	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	50000	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	50000	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	10000	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	10000	-
5.2(Application to the Conductor)	-	2000	-
5.3(Thickness)	-	2000	-
6.2(Sheath application)	-	2000	-
6.3(Sheath Thickness)	-	2000	-
6.4(Sheath Colour)	-	2000	-
7(Overall Dimension)	-	2000	-
8.1(Continuity of Marking)	-	2000	-
8.2(Durability)	-	2000	-
8.3(Legibility)	-	2000	-
9(Core Identification)	-	2000	-
12(Packing and Marking)	-	2000	-
4.1(Resistance)	-	5000	-
7.1.2.1, 7.2.3(Annealing)	-	2000	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	5000	-
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	5000	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	2000	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	5000	-
Annex G and Table 3 of IS 17293:2020(Ozone Resistance test)	-	10000	-
IS 191 : 2007, IS 440(Copper purity test)	-	5000	-
Table 3 of IS 17293:2020 & IS 10810 (Part 63)(Smoke density test.)	-	10000	-
Cl 6.4.3 and Table 3 of IS 8130(Diameter of wire in conductor)	-	2000	-
Table-3 & Annex-F of IS 17293:2020 and IS 10810 (Part 7) 1984(Elongation at low temperature (Cold Elongation))	-	10000	-
Annex H and Table 3 of IS 17293:2020(Damp Heat test)	-	20000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	10000	-
Cl 11.2.3 & Table-3 of IS 17293:2020 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	10000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(IS 17293)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	10000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	10000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(IS 10810-30)	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	10000	-
Annex D and Table 3 of IS 17293:2020(Dynamic Penetration test)	-	10000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	10000	-
Annex C of IS 17293:2020 & IS:10810 (Part 21)-1984(Cold impact test)	-	5000	-
Annex - B of IS 17293:2020(Compatibility test)	-	5000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 20)-1984(Cold bend test)	-	5000	-
Cl. 5.3, 6.3 & Table 1 & 2 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	5000	-
Cl 5.3 of IS 17048:2018 & IS:10810 (Part 53)-1984(Flammability Test)	-	2000	-
Annex A of IS 17293-2020, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	5000	-
Cl 11.2.1 of IS 17293:2020 & IS:10810 (Part 45)-1984(High voltage test)	-	5000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Annex B of IS 17293:2020 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(pH)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Conductivity)	-	5000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(HCl and HBr)	-	20000	-
Annex J (J-1, J-2, J-3 & J-4) of IS 17293:2020(Presence of Fluorine / Fluorine Content (if required))	-	20000	-
Annex B of IS 17293:2020 & IS:10810 (Part 30)-1984(Hot set test)	-	5000	-
"Annex B of IS 17293:2020 & IS:8504-1:2012 and IS: 8504-2: 2013"(Thermal endurance test)	-	20000	-
Annex- I, Annex-B, Table-11 of IS 17293:2020 and IS 10810 (Part 1) : 1984(Sheath resistance against acid and alkaline solution)	-	20000	-
Annex - B of IS 17293:2020(Compatibility test)	-	20000	-
Table 3 of IS 17293:2020 & IS:10810 (Part 12)-1984(Shrinkage test)	-	5000	-
Annex - E of IS 17293 : 2020(UV resistance)	-	30000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(pH)	-	20000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Conductivity)	-	20000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(HCl and HBr)	-	20000	-
Cl 5.7 & Annex D (D.1, D.2, D.3, D.4) of IS 17048:2018.(Presence of Fluorine / Fluorine Content (if required))	-	20000	-
11.2.2(Spark Test)	-	5000	-
11.2.4(Long-term Resistance of Insulation to d.c.)	-	20000	-
11.2.5(Surface Resistance of Sheath)	-	20000	-
11.3.1(Sheath Colour)	-	1000	-
11.3.2(Sheath Marking)	-	1000	-
11.3.3(Overall Diameters and Ovality)	-	2000	-
Annex J(Assessment of Halogens)	-	20000	-
5.1, 6.1, Table 11, 1.1(Properties before ageing b)	-	20000	-
5.1, 6.1, Table 11, 1.2(Properties after ageing in oven)	-	20000	-
5.1, 6.1, Table 11, 1.3(Hot set test b)	-	5000	-
5.1, 6.1, Table 11, 1.4(Thermal endurance Test conditions b)	-	500000	-
5.1, 6.1, Table 11, 1.5(Bending at low temperature)	-	10000	-
5.1, 6.1, Table 11, 1.6(Elongation at low temperature Insulated conductor/cable overall diameter)	-	10000	-
5.1, 6.1, Table 11, 1.7(Sheath resistance against acid and alkaline solution)	-	10000	-
5.1, 6.1, Table 11, 1.8(Compatibility test)	-	10000	-
5.2(Application to the Conductor)	-	2000	-
5.3(Thickness)	-	2000	-
6.2(Sheath application)	-	1000	-
6.3(Sheath Thickness)	-	2000	-
6.4(Sheath Colour)	-	2000	-
7(Overall Dimension)	-	2000	-
8.1(Continuity of Marking)	-	2000	-
8.2(Durability)	-	2000	-
8.3(Legibility)	-	2000	-
9(Core Identification)	-	2000	-
12(Packing and Marking)	-	2000	-
4.1(Resistance)	-	5000	-
7.1.2.1, 7.2.3(Annealing)	-	5000	-
Table 3, (IS 10810 Part 53)(Test for vertical flame propagation on complete cable)	-	30000	-

07 Sep, 2026

-
Included w.e.f.29.07.2025

IS 12776 (2002)

Galvanized strand for earthing - Specification (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Freedom From Defects (IS 12776))	-	1000	-
5.3(Joints in wires (IS 12776))	-	1000	-
6- Annex-A, Sl-2(Size of the wire (IS 12776))	-	1000	-
6- Annex-A, Sl-8(Lay (IS 12776))	-	1000	-
8.1-Annex-A,Sl-9(Breaking Force of Strand (IS 12776))	-	5000	-
8.2-Annex-A,Sl-6(Elongation of wire, IS 10810(Part-37))	-	2000	-
8.2-Annex-A,Sl-3(Tensile Strength of wire IS 10810(Part-37))	-	2000	-
8.3-Annex-A,Sl-12(Resistance at 200 C (IS 12776))	-	2000	-
8.4(Wrapping Test (IS 12776))	-	2000	-
8.5-Annex-A-Sl-7a(Amount of zinc Coating (IS 6745))	-	2000	-
8.5-Annex-A-Sl-7b(Uniformity of Coating (IS 2633))	-	2000	-
8.5-Annex-A-Sl-4(Torsion Test IS 10810(Part-37))	-	2000	-
4.1(Carbon- IS 228(Part 1))	-	2000	-
4.1(Sulphur- IS 228(Part 9))	-	2000	-
4.1(Phosphorous- IS 228(Part 3))	-	2000	-
4.1(Manganese- IS 228(Part 2))	-	2000	-
4.1(Silicon- IS 228(Part 8))	-	2000	-
6- Annex-A, Sl-8(Lay Length)	-	1000	-
5.2(Freedom From Defects (IS 12776))	-	1000	-
5.3(Joints in wires (IS 12776))	-	1000	-
6- Annex-A, Sl-2(Size of the wire (IS 12776))	-	1000	-
6- Annex-A, Sl-8(Lay (IS 12776))	-	1000	-
8.1-Annex-A,Sl-9(Breaking Force of Strand (IS 12776))	-	5000	-
8.2-Annex-A,Sl-6(Elongation of wire, IS 10810(Part-37))	-	2000	-
8.2-Annex-A,Sl-3(Tensile Strength of wire IS 10810(Part-37))	-	2000	-
8.3-Annex-A,Sl-12(Resistance at 200 C (IS 12776))	-	2000	-
8.4(Wrapping Test (IS 12776))	-	2000	-
8.5-Annex-A-Sl-7a(Amount of zinc Coating (IS 6745))	-	2000	-
8.5-Annex-A-Sl-7b(Uniformity of Coating (IS 2633))	-	2000	-
8.5-Annex-A-Sl-4(Torsion Test IS 10810(Part-37))	-	2000	-
4.1(Carbon- IS 228(Part 1))	-	2000	-
4.1(Sulphur- IS 228(Part 9))	-	2000	-
4.1(Phosphorous- IS 228(Part 3))	-	2000	-
4.1(Manganese- IS 228(Part 2))	-	2000	-
4.1(Silicon- IS 228(Part 8))	-	2000	-
6- Annex-A, Sl-8(Lay Length)	-	2000	-
5.2(Freedom From Defects (IS 12776))	-	1000	-
5.3(Joints in wires (IS 12776))	-	1000	-
6- Annex-A, Sl-2(Size of the wire (IS 12776))	-	2000	-
6- Annex-A, Sl-8(Lay (IS 12776))	-	2000	-
8.1-Annex-A,Sl-9(Breaking Force of Strand (IS 12776))	-	3000	-
8.2-Annex-A,Sl-6(Elongation of wire, IS 10810(Part-37))	-	3000	-
8.2-Annex-A,Sl-3(Tensile Strength of wire IS 10810(Part-37))	-	2000	-
8.3-Annex-A,Sl-12(Resistance at 200 C (IS 12776))	-	3000	-
8.4(Wrapping Test (IS 12776))	-	2000	-
8.5-Annex-A-Sl-7a(Amount of zinc Coating (IS 6745))	-	2000	-
8.5-Annex-A-Sl-7b(Uniformity of Coating (IS 2633))	-	2000	-
8.5-Annex-A-Sl-4(Torsion Test IS 10810(Part-37))	-	2000	-
4.1(Carbon- IS 228(Part 1))	-	2000	-
4.1(Sulphur- IS 228(Part 9))	-	2000	-
4.1(Phosphorous- IS 228(Part 3))	-	2000	-
4.1(Manganese- IS 228(Part 2))	-	2000	-
4.1(Silicon- IS 228(Part 8))	-	2000	-
6- Annex-A, Sl-8(Lay Length)	-	1000	-

07 Sep, 2026

-
Included .w.e.f.18.07.2025

IS 398 : Part 6 (2021)

Aluminium Conductors For Overhead Transmission Purposes Part 6: High conductivity aluminium alloy stranded conductors

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.2(Visual Examination)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.4, Table 2(Measurement of Diameter of Individual Aluminium Alloy Wires)	-	2000	-
16.5, Table 2(Breaking Load Test - before stranding)	-	2000	-
16.5, Table 2(Breaking Load Test - after stranding)	-	3000	-
16.6, Table 1(Elongation Test - before stranding)	-	2000	-
16.6, Table 1(Elongation Test - after stranding)	-	3000	-
16.7, Table 2(Resistivity Test)	-	5000	-
16.8(Wrapping Test)	-	2000	-
11(Stranding)	-	2000	-
8(Freedom from defects)	-	2000	-
16.9, Table 3(Ultimate Tensile Strength on Stranded Conductor)	-	30000	-
16.10, Table 3(d.c. Resistance Test on Stranded Conductor)	-	5000	-
16.11(Stress-strain Test)	-	100000	-
16.2(Visual Examination)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	2000	-
16.4, Table 2(Measurement of Diameter of Individual Aluminium Alloy Wires)	-	2000	-
16.5, Table 2(Breaking Load Test - before stranding)	-	3000	-
16.5, Table 2(Breaking Load Test - after stranding)	-	3000	-
16.6, Table 1(Elongation Test - before stranding)	-	3000	-
16.6, Table 1(Elongation Test - after stranding)	-	3000	-
16.7, Table 2(Resistivity Test)	-	5000	-
16.8(Wrapping Test)	-	3000	-
11(Stranding)	-	2000	-
8(Freedom from defects)	-	2000	-
16.9, Table 3(Ultimate Tensile Strength on Stranded Conductor)	-	30000	-
16.10, Table 3(d.c. Resistance Test on Stranded Conductor)	-	5000	-
16.11(Stress-strain Test)	-	100000	-

07 Sep, 2026

-
Included w.e.f.27.06.2025

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-	500	-
6.1(The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-	500	-
6.1(a) Reference to this Indian Standard;)	-	500	-
6.1(b) Manufacturer's name,brand name or trade-mark;)	-	500	-
6.1(c) Size of conductor / maximum overall diameter,)	-	1000	-
6.1(d) Length of conductor on spool / reel /coil;)	-	500	-
6.1(e) Number of lengths onspool / reel / coil (if more than one);)	-	500	-
6.1(f) Country of Manufacturer)	-	500	-
6.1(g) Year of Manufacture.)	-	500	-
6.2(BIS Certification Mark)	-	500	-
4(i) Material)	-	500	-
5(ii) Diameter [mm] Seperate wire:)	-	1000	-
5(ii) Diameter [mm] Wire taken from cable:)	-	1000	-
5(iii) Annealing test [Percentage] on Seperate wire:)	-	1000	-
5(iii) Annealing test [Percentage] on Wire taken from cable:)	-	1000	-
5(d) Resistance test [Ohm/km corrected to 20°c)	-	1000	-
4.1, table 1 & 2(a) Thickness of Polyster (mm))	-	1000	-
4.1, table 1 & 3(b) Thickness of Polypropylene (mm))	-	1000	-
4.1, table 1 & 4(c) Total thickness of Insulation(mm))	-	1000	-
4.2(Application of insulation)	-	500	-
4.3(Colour of Insuation)	-	500	-
4.4(Overall diameter (mm))	-	1000	-
4(Before ageing Tensile strength [N/mm²])	-	2000	-
4(Before ageing Elongation at break [Percentage])	-	2000	-
4(After ageing Tensile strength [N/mm²])	-	2000	-
4(Variation on tensile strangth [Percentage])	-	2000	-
4(After ageing Elongation at break [Percentage])	-	2000	-
4(Variation on elongation at break [Percentage])	-	2000	-
4(Shrinkage test [Percentage])	-	1000	-
4(After Shrinkage Cracks found.)	-	2000	-
4.1(Water absorption test [Gravimetric] [mg/cm²])	-	3000	-
4.1(Hot Deformation test [depth of indentation) [Percentage])	-	2000	-
4.1(Heat Shock Test - No cracks found)	-	1000	-
4.5(High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-	2000	-
4.1(Insulation Resistance test [ohm-cm] At 27 ºC)	-	1000	-
4.1([Insulation Resistance test [ohm-cm] At 90 ºC)	-	1000	-
5(The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-	1000	-
6(The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-	1000	-
6(a) Reference to this Indian Standard;)	-	500	-
6(b) Manufacturer's name,brand name or trade-mark;)	-	500	-
6(c) Size of conductor / maximum overall diameter,)	-	500	-
6(d) Length of conductor on spool / reel /coil;)	-	500	-
6(e) Number of lengths onspool / reel / coil (if more than one);)	-	500	-
6(f) Country of Manufacturer Marking)	-	500	-
6(g) Year of Manufacture.)	-	500	-
6.2(BIS Certification Mark)	-	500	-
4(i) Material)	-	500	-
4(ii) Diameter [mm] Seperate wire:)	-	1000	-
4(ii) Diameter [mm] Wire taken from cable)	-	1000	-
4(iii) Annealing test [Percentage] on Seperate wire:)	-	1000	-
4([iii) Annealing test [Percentage] on Wire taken from cable:)	-	1000	-
4(d) Resistance test [Ohm/km corrected to 20°c])	-	1000	-
4(a) Thickness of Polyster (mm))	-	1000	-
4(b) Thickness of Polypropylene (mm))	-	1000	-
4(c) Total thickness of Insulation(mm))	-	1000	-
4(Application of insulation)	-	500	-
4(Colour of Insuation)	-	500	-
4(Overall diameter (mm))	-	1000	-
4(Before ageing Tensile strength [N/mm²])	-	1000	-
4(Before ageing Elongation at break [Percentage])	-	1000	-
4(After ageing Tensile strength [N/mm²])	-	2000	-
4(Variation on tensile strangth [Percentage])	-	2000	-
4(After ageing Elongation at break [Percentage])	-	2000	-
4(Variation on elongation at break [Percentage])	-	2000	-
4(Shrinkage test [Percentage])	-	1000	-
4(After Shrinkage Cracks found.)	-	1000	-
4(Water absorption test [Gravimetric] [mg/cm²])	-	2000	-
4(Hot Deformation test [depth of indentation) [Percentage])	-	2000	-
4(Heat Shock Test - No cracks found Physical)	-	1000	-
4(High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-	1000	-
4(Insulation Resistance test [ohm-cm] At 27 ºC)	-	1000	-
4(Insulation Resistance test [ohm-cm] At 90 ºC)	-	1000	-
Clause No. 3(Insulation Resistance (Volume Resistivity at test temperature 90 º C ))	-	1000	-
Clause No. 3(Water absorption)	-	2000	-
Clause No. 3(Hot Deformation)	-	2000	-
Clause No. 3(Shrinkage)	-	1000	-
Clause No. 3(Heat Shock)	-	1000	-
Clause No. 3(Thickness of Insulation)	-	1000	-
Clause No. 3(Annealing Test)	-	1000	-
Clause No. 3(Conductor Diameter)	-	1000	-
Clause No. 3(Overall Dimensions)	-	1000	-
Clause No. 3(Insulation Resistance (Volume Resistivity at 27º C ))	-	1000	-
Clause No. 3(High Voltage Test (Water Immersion test) at room temperature)	-	2000	-
Clause No. 3(Conductor Resistance)	-	1000	-
Table 1, Cl. 4.1, VI(Water Absorbtion Test (Gravimetric))	-	2000	-
Cl. 4.1 of IS: 8783 (Pt-2)(Insulation Resistance Test)	-	1000	-
Cl. 4.1 of IS: 8783 (Pt-2)(Insulation Resistance Test)	-	1000	-
Cl.4.1 of IS: 8783 (Pt-2):1995(Physical Test for Insulation after Ageing (on finished wire))	-	2000	-

07 Sep, 2026

-
Included w.e.f.09.07.2025

IS 302 : Part 2 : Sec 21 (2024)

Household and Similar Electrical Appliancesï¿½Safety Part 2 Particular Requirements Section 21 Storage Water Heaters

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General requirement)	-	500	10% discount to BIS
5(General conditions for the tests)	-	500	10% discount to BIS
6(Classification)	-	1000	10% discount to BIS
7(Marking and instructions)	-	500	10% discount to BIS
8(Protection against access to live parts)	-	1000	10% discount to BIS
10(Power input and current)	-	1000	10% discount to BIS
11(Heating)	-	1000	10% discount to BIS
13(Leakage current and electric strength at operating temperature)	-	1000	10% discount to BIS
14(Transient overvoltages)	-	500	10% discount to BIS
15(Moisture resistance)	-	5000	10% discount to BIS
16(Leakage current and electric strength)	-	1000	10% discount to BIS
17(Overload protection of transformers and associated circuits)	-	500	10% discount to BIS
19(Abnormal operation)	-	1000	10% discount to BIS
20(Stability and mechanical hazards)	-	1000	10% discount to BIS
21(Mechanical strength)	-	1000	10% discount to BIS
22(Construction)	-	2000	10% discount to BIS
23(Internal wiring)	-	500	10% discount to BIS
24(Components)	-	500	10% discount to BIS
25(Supply connection and external flexible cords)	-	500	10% discount to BIS
26(Terminals for external conductors)	-	500	10% discount to BIS
27(Provision for earthing)	-	500	10% discount to BIS
28(Screws and connections)	-	500	10% discount to BIS
29(Clearances, creepage distances and solid insulation)	-	500	10% discount to BIS
30(Resistance to heat and fire)	-	1000	10% discount to BIS
31(Resistance to rusting)	-	500	10% discount to BIS
32(Radiation, toxicity and similar hazards)	-	500	10% discount to BIS
A.101(Pressure test)	-	500	10% discount to BIS
12(Charging of metal-ion batteries)	-	500	10% discount to BIS
22.101(rated pressure)	-	500	10% discount to BIS
22.102(Closed water heaters)	-	500	10% discount to BIS
22.103(Addition)	-	500	10% discount to BIS
22.104(Addition)	-	500	10% discount to BIS
22.105(Cistern-type water heaters)	-	500	10% discount to BIS
22.109(Addition)	-	500	10% discount to BIS
19.11.4.4(Surge immunity test)	-	1000	10% discount to BIS
9(Starting of motor-operated appliances)	-	500	10% discount to BIS
18(Endurance)	-	500	10% discount to BIS
4(General requirement)	-	-	-
5(General conditions for the tests)	-	-	-
6(Classification)	-	-	-
7(Marking and instructions)	-	-	-
8(Protection against access to live parts)	-	-	-
10(Power input and current)	-	-	-
11(Heating)	-	-	-
13(Leakage current and electric strength at operating temperature)	-	-	-
14(Transient overvoltages)	-	-	-
15(Moisture resistance)	-	-	-
16(Leakage current and electric strength)	-	-	-
17(Overload protection of transformers and associated circuits)	-	-	-
19(Abnormal operation)	-	-	-
20(Stability and mechanical hazards)	-	-	-
21(Mechanical strength)	-	-	-
22(Construction)	-	-	-
23(Internal wiring)	-	-	-
24(Components)	-	-	-
25(Supply connection and external flexible cords)	-	-	-
26(Terminals for external conductors)	-	-	-
27(Provision for earthing)	-	-	-
28(Screws and connections)	-	-	-
29(Clearances, creepage distances and solid insulation)	-	-	-
30(Resistance to heat and fire)	-	-	-
31(Resistance to rusting)	-	-	-
32(Radiation, toxicity and similar hazards)	-	-	-
A.101(Pressure test)	-	-	-
12(Charging of metal-ion batteries)	-	-	-
22.101(rated pressure)	-	-	-
22.102(Closed water heaters)	-	-	-
22.103(Addition)	-	-	-
22.104(Addition)	-	-	-
22.105(Cistern-type water heaters)	-	-	-
22.109(Addition)	-	-	-
19.11.4.4(Surge immunity test)	-	-	-
9(Starting of motor-operated appliances)	-	-	-
18(Endurance)	-	-	-

07 Sep, 2026

-
Included w.e.f 07.05.2025 Exclusion Cl 19.11.4.1- 19.11.4.7(EMI/EMC)

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	600	-
6(Classification- IS 302-1)	-	600	-
11.8(Temperature rise)	-	600	-
11.7(Duration corresponding)	-	600	-
11.6(Combined appliances)	-	600	-
11.5(Motor-operated appliances)	-	600	-
11.4(Heating appliances)	-	600	-
8.1.5(Live parts of built-in appliances)	-	600	-
18(Endurance)	-	600	-
17(Overload protection of transformers and associated circuits)	-	600	-
16(Leakage current and electric strength)	-	600	-
4(General requirement)	-	600	-
32.1(Radiation Toxicity and Similar Hazards)	-	600	-
31(Resistance to Rusting)	-	600	-
30.2(Needle Flame Test)	-	600	-
30.2(Glow Wire Test)	-	600	-
30.1(Ball pressure test)	-	600	-
29(clearance, creepage distances and solid insulation)	-	600	-
28(Screw test and connections)	-	600	-
27.1(Provision for Earthing, IS 302-1)	-	600	-
26(Terminals for external conductors)	-	600	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	600	-
24(Components)	-	600	-
23.1(Internal Wiring, IS 302-1)	-	600	-
22.1(Construction, IS 302-1)	-	600	-
21.1(Mechanical Strength, IS 302-1)	-	600	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	600	-
19(Abnormal Operation)	-	600	-
18(Endurance)	-	600	-
17(Over Load Protection of Transformers and associated circuits)	-	600	-
16.3(Electric Strength (after clause 15 and 16.2))	-	600	-
16.2(Leakage Current (after Clause 15))	-	600	-
16.1(General)	-	600	-
15.3(Humidity Test)	-	600	-
15.2(Spillage Test)	-	600	-
15.1(Ingress Protection test other than IPX0 (IP test))	-	600	-
15.0(Moisture resistance)	-	600	-
14(Transient Over Voltages)	-	600	-
13.3(Electric Strength at operating temperature)	-	600	-
13.2(Leakage current at operating temperature)	-	600	-
13(Leakage current and electric strength at operating temperature)	-	600	-
11.3(Heating)	-	600	-
11.2(General)	-	600	-
11.1(General)	-	600	-
10.2(Current input)	-	600	-
10.1(Power input)	-	600	-
9(Starting of motor operation test requirements and tests)	-	600	-
8.1.4(Protection against live parts against protective impedance)	-	700	-
8.1.3(Protection against live parts in visible glowing heating elements)	-	600	-
8.1.2(Protection against live parts in openings)	-	600	-
8.1.1(Protection against live parts in all positions)	-	600	-
7(Marking and instructions)	-	600	-
A.2(Earth continuity test)	-	700	-
Annex C(Ageing test on motors)	-	600	-
Annex D(Thermal motor protectors)	-	600	-
19.17(Abnormal Operation, IS 302-1)	-	600	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	600	-
21.2(Mechanical Strength, IS 302-1)	-	700	-
21.3(Mechanical Strength, IS 302-1)	-	600	-
22.5(Construction)	-	700	-
22.6(Construction, IS 302-1)	-	600	-
22.11(Construction, IS 302-1)	-	700	-
22.16(Construction)	-	600	-
22.32(Construction, IS 302-1)	-	700	-
22.42(Construction)	-	600	-
23.3(Internal Wiring, IS 302-1)	-	700	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	700	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	600	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	700	-
26.5(Terminals for external conductors)	-	600	-
27.5(Provision for Earthing, IS 302-1)	-	700	-
28.1(Screws and connections)	-	600	-
22.2(Construction, IS 302-1)	-	700	-
22.3(Construction, IS 302-1)	-	600	-
B.22.4(Construction, IS 302-1)	-	600	-
B.22.5(Construction, IS 302-1)	-	700	-
19.11.4.4(Surge immunity test)	-	600	-
5(General conditions for the tests)	-	700	-
25.6(Supply connection and external flexible cords, IS 302-1)	-	600	-
16.0(General)	-	700	-
15.2(Moisture resistance)	-	600	-

07 Sep, 2026

-
Included w.e.f.25.03.2025 Exclusion Cl 19.11.4.1 to Cl 19.11.4.7 (EMI/EMC) "Domestic Electric Clothes Washing Machines (For testing charges please refer part 2 standard in LIMS)"

IS 16270 (2023)

Secondary cells and batteries for solar photovoltaic application - General requirements and methods of test

626400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Photovoltaic Energy System)	-	10000	20% Discount to BIS
Cl-4.2(Secondary Cells and Batteries)	-	10000	20% Discount to BIS
Cl-4.3(General Operating Conditions)	-	10000	20% Discount to BIS
Cl-4.3.8(Storage)	-	10000	20% Discount to BIS
Cl-4.3.9(Operating Temperature)	-	10000	20% Discount to BIS
Cl-5.1(Mechanical Endurance)	-	10000	20% Discount to BIS
Cl-5.2(Charge Efficiency)	-	10000	20% Discount to BIS
Cl-5.3(Deep Discharge Protection)	-	10000	20% Discount to BIS
Cl-5.4(Marking)	-	10000	20% Discount to BIS
Cl-5.5(Safety)	-	10000	20% Discount to BIS
Cl-5.6(Documentation)	-	10000	20% Discount to BIS
Cl-6(Functional characteristice)	-	10000	20% Discount to BIS
Cl-7(General test conditions)	-	10000	20% Discount to BIS
Cl-8.1(Capacity Test)	-	10000	20% Discount to BIS
Cl-8.2(Endurance Test)	-	226400	20% Discount to BIS
Cl-8.3(Charge Retention Test)	-	10000	20% Discount to BIS
Cl-8.4(Cycle Endurance in Photovoltaic Application (Extreme Conditions))	-	200000	20% Discount to BIS
Cl-8.5(Sulphation Test (Applicable for Lead Acid Batteries only))	-	10000	20% Discount to BIS
Cl-8.6(Water Loss Test (Valid for Flooded Lead Acid Batteries only))	-	10000	20% Discount to BIS
Cl-9.1(Type Tests)	-	10000	20% Discount to BIS
Cl-9.2(Acceptance Test)	-	10000	20% Discount to BIS
4.3.7.1(Specific gravity)	-	10000	20% Discount to BIS

07 Sep, 2026

-
Included.w.e.f.24.12.2024

IS 191 (2007)

Copper - Specification (Fourth Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-Table 1(GRADES/DESIGNATIONS)	-	100	10% discount to BIS
5.1- Table 2(L)	-	100	10% discount to BIS
5.1- Table 2(L1)	-	100	10% discount to BIS
5.1- Table 2(h)	-	100	10% discount to BIS
5.1- Table 2(h1)	-	100	10% discount to BIS
5.1- Table 2(b)	-	100	10% discount to BIS
5.1- Table 2(b1)	-	100	10% discount to BIS
5.1- Table 2(R)	-	100	10% discount to BIS
5.1- Table 2(R1)	-	100	10% discount to BIS
5.1- Table 2(R2 )	-	100	10% discount to BIS
5.1- Table 2(α )	-	100	10% discount to BIS
5.1- Table 2( β )	-	100	10% discount to BIS
5.1- Table 2(γ)	-	100	10% discount to BIS
5.2(Billets)	-	100	10% discount to BIS
5.4-Table 3 (For Billets)(Mass)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Diameter)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Length)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	100	10% discount to BIS
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Ingots)(Mass)	-	100	10% discount to BIS
5.4-Table 3 (Cast cakes)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(thickness )	-	100	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	100	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Silver- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Phosphorus- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Arsenic- IS440)	-	100	10% discount to BIS
7.1 - Table 4(Antimony-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Bismuth-IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Iron IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Lead IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Nickel IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Oxygen IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Selenium - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Sulphur- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tellurium- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tin - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Znic-IS 440)	-	100	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	100	-
7.1 - Table 4(Total Impurities- IS 440)	-	100	-
8.1(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
8.2(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
9.1- Table 5(Mass Resistivity- IS 3635)	-	100	10% discount to BIS
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	100	10% discount to BIS
4-Table 1(GRADES/DESIGNATIONS)	-	100	10% discount to BIS
5.1- Table 2(L)	-	100	10% discount to BIS
5.1- Table 2(L1)	-	100	10% discount to BIS
5.1- Table 2(h)	-	100	10% discount to BIS
5.1- Table 2(h1)	-	100	10% discount to BIS
5.1- Table 2(b)	-	100	10% discount to BIS
5.1- Table 2(b1)	-	100	10% discount to BIS
5.1- Table 2(R)	-	100	10% discount to BIS
5.1- Table 2(R1)	-	100	10% discount to BIS
5.1- Table 2(R2 )	-	100	10% discount to BIS
5.1- Table 2(α )	-	100	10% discount to BIS
5.1- Table 2( β )	-	100	10% discount to BIS
5.1- Table 2(γ)	-	100	10% discount to BIS
5.2(Billets)	-	100	10% discount to BIS
5.4-Table 3 (For Billets)(Mass)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Diameter)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Length)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	100	10% discount to BIS
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Ingots)(Mass)	-	100	10% discount to BIS
5.4-Table 3 (Cast cakes)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(thickness )	-	100	10% discount to BIS
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Silver- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Phosphorus- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Arsenic- IS440)	-	100	10% discount to BIS
7.1 - Table 4(Antimony-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Bismuth-IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Iron IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Lead IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Nickel IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Oxygen IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Selenium - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Sulphur- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tellurium- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tin - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Znic-IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Total Impurities- IS 440)	-	100	10% discount to BIS
8.1(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
8.2(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
9.1- Table 5(Mass Resistivity- IS 3635)	-	100	10% discount to BIS
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	100	10% discount to BIS
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	100	10% discount to BIS
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	100	10% discount to BIS
13(Marking)	-	100	10% discount to BIS
13(Marking)	-	100	10% discount to BIS
13(Marking)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(Width)	-	100	10% discount to BIS
4-Table 1(GRADES/DESIGNATIONS)	-	100	10% discount to BIS
5.1- Table 2(L)	-	100	10% discount to BIS
5.1- Table 2(L1)	-	100	10% discount to BIS
5.1- Table 2(h)	-	100	10% discount to BIS
5.1- Table 2(h1)	-	100	10% discount to BIS
5.1- Table 2(b)	-	100	10% discount to BIS
5.1- Table 2(b1)	-	100	10% discount to BIS
5.1- Table 2(R)	-	100	10% discount to BIS
5.1- Table 2(R1)	-	100	10% discount to BIS
5.1- Table 2(R2 )	-	100	10% discount to BIS
5.1- Table 2(α )	-	100	10% discount to BIS
5.1- Table 2( β )	-	100	10% discount to BIS
5.1- Table 2(γ)	-	100	10% discount to BIS
5.2(Billets)	-	100	10% discount to BIS
5.4-Table 3 (For Billets)(Mass)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Diameter)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Length)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	100	10% discount to BIS
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Ingots)(Mass)	-	100	10% discount to BIS
5.4-Table 3 (Cast cakes)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	100	10% discount to BIS
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Silver- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Phosphorus- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Arsenic- IS440)	-	100	10% discount to BIS
7.1 - Table 4(Antimony-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Bismuth-IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Iron IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Lead IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Nickel IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Oxygen IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Selenium - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Sulphur- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tellurium- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tin - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Znic-IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Total Impurities- IS 440)	-	100	10% discount to BIS
8.1(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
8.2(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
9.1- Table 5(Mass Resistivity- IS 3635)	-	100	10% discount to BIS
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	100	10% discount to BIS
4-Table 1(GRADES/DESIGNATIONS)	-	100	10% discount to BIS
5.1- Table 2(L)	-	100	10% discount to BIS
5.1- Table 2(L1)	-	100	10% discount to BIS
5.1- Table 2(h)	-	100	10% discount to BIS
5.1- Table 2(h1)	-	100	10% discount to BIS
5.1- Table 2(b)	-	100	10% discount to BIS
5.1- Table 2(b1)	-	100	10% discount to BIS
5.1- Table 2(R)	-	100	10% discount to BIS
5.1- Table 2(R1)	-	100	10% discount to BIS
5.1- Table 2(R2 )	-	100	10% discount to BIS
5.1- Table 2(α )	-	100	10% discount to BIS
5.1- Table 2( β )	-	100	10% discount to BIS
5.1- Table 2(γ)	-	100	10% discount to BIS
5.2(Billets)	-	100	10% discount to BIS
5.4-Table 3 (For Billets)(Mass)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Diameter)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Length)	-	100	10% discount to BIS
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	100	10% discount to BIS
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	100	10% discount to BIS
5.4-Table 3 (Ingots)(Mass)	-	100	10% discount to BIS
5.4-Table 3 (Cast cakes)(Mass)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(thickness )	-	100	10% discount to BIS
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Silver- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Phosphorus- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Arsenic- IS440)	-	100	10% discount to BIS
7.1 - Table 4(Antimony-IS440)	-	100	10% discount to BIS
7.1 - Table 4(Bismuth-IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Iron IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Lead IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Nickel IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Oxygen IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Selenium - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Sulphur- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tellurium- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Tin - IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Znic-IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	100	10% discount to BIS
7.1 - Table 4(Total Impurities- IS 440)	-	100	10% discount to BIS
8.1(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
8.2(FREEDOM FROM DEFECTS)	-	100	10% discount to BIS
9.1- Table 5(Mass Resistivity- IS 3635)	-	100	10% discount to BIS
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	100	10% discount to BIS
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	100	10% discount to BIS
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	100	10% discount to BIS
13(Marking)	-	100	10% discount to BIS
13(Marking)	-	100	10% discount to BIS
13(Marking)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	100	10% discount to BIS
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	100	10% discount to BIS
5.3-Table 3 (Cast cakes)(Width)	-	100	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 20.11.2024 "All grades except Cu-DHP, Cu-DPA and Cu-ATP"

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

180000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	2500	10% discount to BIS
4.1.1 b) (Material : Seperator tape )	-	2500	10% discount to BIS
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	2500	10% discount to BIS
4.1.1 e) (Shape of conductor )	-	2500	10% discount to BIS
4.1.1 f) (Nominal size of conductor )	-	2500	10% discount to BIS
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	2500	10% discount to BIS
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	2500	10% discount to BIS
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	2500	10% discount to BIS
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	2500	10% discount to BIS
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	2500	10% discount to BIS
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.3(Fillers)	-	2500	10% discount to BIS
4.4(Binder Tape)	-	2500	10% discount to BIS
4.5.1,13.4, 14.4(Sheath : Compound )	-	2500	10% discount to BIS
4.5.2, 13.4, 14.4(Sheath : Application)	-	2500	10% discount to BIS
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	2500	10% discount to BIS
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	2500	10% discount to BIS
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	2500	10% discount to BIS
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	2500	10% discount to BIS
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	2500	10% discount to BIS
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	2500	10% discount to BIS
4.5.6, 13.4(Colour of Sheath)	-	2500	10% discount to BIS
5.1(High Voltage Test (at Room Temperature))	-	2500	10% discount to BIS
5.2(Spark Test (Routine Test))	-	2500	10% discount to BIS
5.3(Flammability Test- IS 10810 (Part 53).)	-	2500	10% discount to BIS
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	2500	10% discount to BIS
5.5(Temperature Index-IS 10810 (Part 64).)	-	2500	10% discount to BIS
5.6(Smoke Density-IS 10810 (Part 63).)	-	2500	10% discount to BIS
5.7(Assessment of Halogen- Table 1 of Annex D)	-	2500	10% discount to BIS
5.1(Persulphate Test- IS 10810 (Part 4).)	-	2500	10% discount to BIS
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	2500	10% discount to BIS
5.12(Hot Set Test- IS 10810 (Part 30).)	-	2500	10% discount to BIS
5.12(Permanent Set - IS 10810 (Part 30).)	-	2500	10% discount to BIS
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	2500	10% discount to BIS
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	2500	10% discount to BIS
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	2500	10% discount to BIS
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	2500	10% discount to BIS
6.1, Table 1(CORE IDENTIFICATION)	-	2500	10% discount to BIS
6.2(Core Identification by Numbers)	-	2500	10% discount to BIS
6.2.1(Preferred Arrangement of Marking)	-	2500	10% discount to BIS
6.2.2(Durability)	-	2500	10% discount to BIS
7.0(CABLE CODE)	-	2500	10% discount to BIS
9.0( IDENTIFICATION)	-	2500	10% discount to BIS
10.1(Packing )	-	2500	10% discount to BIS
10.2(marking)	-	2500	10% discount to BIS
10.2.1(Standards marking)	-	2500	10% discount to BIS
13.3, 14.3(assembly of cores )	-	2500	10% discount to BIS
6.1(General Requirements)	-	2500	10% discount to BIS
6.1.1(Colour Combination Green Yellow)	-	2500	10% discount to BIS
12.1(Conductor)	-	2500	10% discount to BIS
12.2, Table 4(insulation)	-	2500	10% discount to BIS
4.3.1 (b)(pH test (Fillers))	-	2500	10% discount to BIS
4.3.1 (a)(HCl test (Fillers))	-	2500	10% discount to BIS
5.7 (a)(HCl test (Assessment of halogen test))	-	2500	10% discount to BIS
5.7 (b)(pH test (Assessment of halogen test))	-	2500	10% discount to BIS
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	2500	10% discount to BIS
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	2500	10% discount to BIS
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	2500	10% discount to BIS
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	2500	10% discount to BIS
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	2500	10% discount to BIS
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2500	10% discount to BIS
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	2500	10% discount to BIS
Table 4(Copper Purity test)	-	2500	10% discount to BIS
4.3.1 (e)(Fluorine content test (Fillers))	-	2500	10% discount to BIS
4.3.1 (d)(Presence of fluorine test (Fillers))	-	2500	10% discount to BIS
4.3.1 (c)(Conductivity test (Fillers))	-	2500	10% discount to BIS
5.7 (c)(Conductivity test (Assessment of halogen test))	-	2500	10% discount to BIS
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	2500	10% discount to BIS
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	2500	10% discount to BIS
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	2500	10% discount to BIS

07 Sep, 2026

-
Included.w.e.f.24.12.2024

IS 9857 (1990)

Welding cables - Specification (First Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor : Material )	-	1000	10% discount to BIS
5(SEPARATOR)	-	1000	10% discount to BIS
7(CONDUCTOR : CONSTRUCTION )	-	1000	10% discount to BIS
6(COVERING)	-	1000	10% discount to BIS
8(S E P A R A T O R)	-	1000	10% discount to BIS
9.1(C O V E R I N G : Application )	-	1000	10% discount to BIS
9.2(T h i c k n e s s o f C o v e r i n g)	-	1000	10% discount to BIS
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	1000	10% discount to BIS
9.4(A p p l i c a t i o n of C o v e r i n g)	-	1000	10% discount to BIS
9.5(Colour of C o v e r i n g)	-	1000	10% discount to BIS
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	1000	10% discount to BIS
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	1000	10% discount to BIS
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	1000	10% discount to BIS
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	1000	10% discount to BIS
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	1000	10% discount to BIS
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	1000	10% discount to BIS
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	1000	10% discount to BIS
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	1000	10% discount to BIS
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	1000	10% discount to BIS
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	1000	10% discount to BIS
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	1000	10% discount to BIS
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	1000	10% discount to BIS
10.1 c) 5)(Hot set test )	-	1000	10% discount to BIS
10.1 c) 5)(Permanent set )	-	1000	10% discount to BIS
11.1(High Voltage Test ( Water Immersion Test ))	-	1000	10% discount to BIS
11.2(Spark Test)	-	1000	10% discount to BIS
11.3(Static Flexibility Test)	-	1000	10% discount to BIS
11.4(Flammability Test)	-	1000	10% discount to BIS
12.1(Manufacturer's Identification)	-	1000	10% discount to BIS
12.2(Cable Identification)	-	1000	10% discount to BIS
12.3(Cable Code)	-	1000	10% discount to BIS
13.1(Packing )	-	1000	10% discount to BIS
13.2(Marking)	-	1000	10% discount to BIS
14(CABLE RATINGS)	-	1000	10% discount to BIS
15(VOLTAGE DROP)	-	1000	10% discount to BIS
Table 4(Copper purity test)	-	1000	10% discount to BIS
Table 2(Oil resistance - Elongation)	-	1000	10% discount to BIS
Table 2(Oil resistance - Tensile strength )	-	1000	10% discount to BIS
Table 2(Ageing in air bomb - Elongation)	-	1000	10% discount to BIS
Table 2(Ageing in air bomb - Tensile strength )	-	1000	10% discount to BIS
Table 1 (Thickness of covering)	-	1000	10% discount to BIS
15.1 (d)(Heat Shock Test)	-	1000	10% discount to BIS
15.1 (d)(Hot Deformation Test)	-	1000	10% discount to BIS
15.1 (d)(Loss Of Mass Test)	-	1000	10% discount to BIS
10.1(b), Table 1(Thickness of covering)	-	1000	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 11-09-2024.

IS 9968 : Part 1 (1988)

Specification for elastomer insulatedcables: Part 1 for working voltages up to and including 1100 volts (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1( Copper Cooduetor)	-	500	10% discount to BIS
3.2(Aluminium conductor)	-	500	10% discount to BIS
4.1(INSULATION : lnsulation for General Service)	-	500	10% discount to BIS
4.2(INSULATION : Heat Resisting insulation)	-	500	10% discount to BIS
4.3(INSULATION : Silicone Rubber Insulation)	-	500	10% discount to BIS
5.1(TAPE : Proofed Tape)	-	500	10% discount to BIS
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	500	10% discount to BIS
5.3(TAPE : Giass Tape)	-	500	10% discount to BIS
6.1(FILLERS : )	-	500	10% discount to BIS
7.1(BRAID : Textile Braid)	-	500	10% discount to BIS
7.2(BRAID : Glass Braid )	-	500	10% discount to BIS
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	500	10% discount to BIS
8.2(SHEATH :Heat Resisting Insulated Cables)	-	500	10% discount to BIS
9.1(PresenRtive Compound)	-	500	10% discount to BIS
9.2(Varnish)	-	500	10% discount to BIS
10( Conductor )	-	500	10% discount to BIS
11(Separator tape)	-	500	10% discount to BIS
12.2(Insulation : Thickness of Insufatien)	-	500	10% discount to BIS
12.4(Insulation : Allplication of Insulation)	-	500	10% discount to BIS
13(CORE IDENTiFICATlON)	-	500	10% discount to BIS
14(Tape)	-	500	10% discount to BIS
15(BRAIDING)	-	500	10% discount to BIS
16(COMPOUNDING AND VARNISHING)	-	500	10% discount to BIS
17(LAYING UP OF CORES)	-	500	10% discount to BIS
18( Binder tape)	-	500	10% discount to BIS
19.2(Sheath : Thickness of Sheath)	-	500	10% discount to BIS
19.4( Sheath :Colour)	-	500	10% discount to BIS
20( Overall diameter)	-	500	10% discount to BIS
21. (a)(Persulphate tests (for copper))	-	500	10% discount to BIS
21. (b)(Annealing Test (for coper))	-	500	10% discount to BIS
21. (c)( Tensile Test (for aluminium))	-	500	10% discount to BIS
21. (d)( Wrapping Test (for aluminium))	-	500	10% discount to BIS
21. (e)(Conductor Resistance )	-	500	10% discount to BIS
21.1( Tensile strength )	-	500	10% discount to BIS
22.1( Elongation)	-	500	10% discount to BIS
21.1(type test : Ageing In air oven)	-	500	10% discount to BIS
21.1(type test : Ageing in air bomb)	-	500	10% discount to BIS
21.1(type test : Ageing In oxygen bomb)	-	500	10% discount to BIS
21.1(type test : Hot set elongation)	-	1000	10% discount to BIS
21.1(type test : Tear resistance )	-	500	10% discount to BIS
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	500	10% discount to BIS
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	500	10% discount to BIS
21(Water absorption test)	-	500	10% discount to BIS
23(identification)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	500	10% discount to BIS
Cl No. 22.2(High Voltage Test (Water Immersion))	-	500	10% discount to BIS
Cl No. 4.1(Insulation resistance)	-	500	10% discount to BIS
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	500	10% discount to BIS
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	500	10% discount to BIS
Cl No. 23.1, 23.2(Identification)	-	500	10% discount to BIS
21.1((f) Oil resistance)	-	500	10% discount to BIS
3.1( Copper Cooduetor)	-	500	10% discount to BIS
3.2(Aluminium conductor)	-	500	10% discount to BIS
4.1(INSULATION : lnsulation for General Service)	-	500	10% discount to BIS
4.2(INSULATION : Heat Resisting insulation)	-	500	10% discount to BIS
4.3(INSULATION : Silicone Rubber Insulation)	-	500	10% discount to BIS
5.1(TAPE : Proofed Tape)	-	500	10% discount to BIS
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	500	10% discount to BIS
5.3(TAPE : Giass Tape)	-	500	10% discount to BIS
6.1(FILLERS : )	-	500	10% discount to BIS
7.1(BRAID : Textile Braid)	-	500	10% discount to BIS
7.2(BRAID : Glass Braid )	-	500	10% discount to BIS
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	500	10% discount to BIS
8.2(SHEATH :Heat Resisting Insulated Cables)	-	500	10% discount to BIS
9.1(PresenRtive Compound)	-	500	10% discount to BIS
9.2(Varnish)	-	500	10% discount to BIS
10( Conductor )	-	500	10% discount to BIS
11(Separator tape)	-	500	10% discount to BIS
12.2(Insulation : Thickness of Insufatien)	-	500	10% discount to BIS
12.4(Insulation : Allplication of Insulation)	-	500	10% discount to BIS
13(CORE IDENTiFICATlON)	-	500	10% discount to BIS
14(Tape)	-	500	10% discount to BIS
15(BRAIDING)	-	500	10% discount to BIS
16(COMPOUNDING AND VARNISHING)	-	500	10% discount to BIS
17(LAYING UP OF CORES)	-	500	10% discount to BIS
18( Binder tape)	-	500	-
19.2(Sheath : Thickness of Sheath)	-	500	-
19.4( Sheath :Colour)	-	500	-
20( Overall diameter)	-	500	-
21. (a)(Persulphate tests (for copper))	-	500	-
21. (b)(Annealing Test (for coper))	-	500	-
21. (c)( Tensile Test (for aluminium))	-	500	-
21. (d)( Wrapping Test (for aluminium))	-	500	-
21. (e)(Conductor Resistance )	-	500	-
21.1( Tensile strength )	-	500	-
22.1( Elongation)	-	500	-
21.1(type test : Ageing In air oven)	-	500	-
21.1(type test : Ageing in air bomb)	-	500	-
21.1(type test : Ageing In oxygen bomb)	-	500	-
21.1(type test : Hot set elongation)	-	500	-
21.1(type test : Tear resistance )	-	500	-
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	500	10% discount to BIS
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	500	10% discount to BIS
21(Water absorption test)	-	500	10% discount to BIS
23(identification)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	500	10% discount to BIS
Cl No. 22.2(High Voltage Test (Water Immersion))	-	500	10% discount to BIS
Cl No. 4.1(Insulation resistance)	-	500	10% discount to BIS
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	500	10% discount to BIS
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	500	10% discount to BIS
Cl No. 23.1, 23.2(Identification)	-	500	10% discount to BIS
21.1((f) Oil resistance)	-	500	10% discount to BIS
3.1( Copper Cooduetor)	-	500	10% discount to BIS
3.2(Aluminium conductor)	-	500	10% discount to BIS
4.1(INSULATION : lnsulation for General Service)	-	500	10% discount to BIS
4.2(INSULATION : Heat Resisting insulation)	-	500	10% discount to BIS
4.3(INSULATION : Silicone Rubber Insulation)	-	500	10% discount to BIS
5.1(TAPE : Proofed Tape)	-	500	10% discount to BIS
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	500	10% discount to BIS
5.3(TAPE : Giass Tape)	-	500	10% discount to BIS
6.1(FILLERS : )	-	500	10% discount to BIS
7.1(BRAID : Textile Braid)	-	500	10% discount to BIS
7.2(BRAID : Glass Braid )	-	500	10% discount to BIS
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	500	10% discount to BIS
8.2(SHEATH :Heat Resisting Insulated Cables)	-	500	10% discount to BIS
9.1(PresenRtive Compound)	-	500	10% discount to BIS
9.2(Varnish)	-	500	10% discount to BIS
10( Conductor )	-	500	10% discount to BIS
11(Separator tape)	-	500	10% discount to BIS
12.2(Insulation : Thickness of Insufatien)	-	500	10% discount to BIS
12.4(Insulation : Allplication of Insulation)	-	500	10% discount to BIS
13(CORE IDENTiFICATlON)	-	500	10% discount to BIS
14(Tape)	-	500	10% discount to BIS
15(BRAIDING)	-	500	10% discount to BIS
16(COMPOUNDING AND VARNISHING)	-	500	10% discount to BIS
17(LAYING UP OF CORES)	-	500	10% discount to BIS
18( Binder tape)	-	500	10% discount to BIS
19.2(Sheath : Thickness of Sheath)	-	500	10% discount to BIS
19.4( Sheath :Colour)	-	500	10% discount to BIS
20( Overall diameter)	-	500	10% discount to BIS
21. (a)(Persulphate tests (for copper))	-	500	10% discount to BIS
21. (b)(Annealing Test (for coper))	-	500	10% discount to BIS
21. (c)( Tensile Test (for aluminium))	-	500	10% discount to BIS
21. (d)( Wrapping Test (for aluminium))	-	500	10% discount to BIS
21. (e)(Conductor Resistance )	-	500	10% discount to BIS
21.1( Tensile strength )	-	500	10% discount to BIS
22.1( Elongation)	-	500	10% discount to BIS
21.1(type test : Ageing In air oven)	-	500	10% discount to BIS
21.1(type test : Ageing in air bomb)	-	500	10% discount to BIS
21.1(type test : Ageing In oxygen bomb)	-	500	10% discount to BIS
21.1(type test : Hot set elongation)	-	500	10% discount to BIS
21.1(type test : Tear resistance )	-	500	10% discount to BIS
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	500	10% discount to BIS
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	500	10% discount to BIS
21(Water absorption test)	-	500	10% discount to BIS
23(identification)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	500	10% discount to BIS
Cl No. 22.2(High Voltage Test (Water Immersion))	-	500	10% discount to BIS
Cl No. 4.1(Insulation resistance)	-	500	10% discount to BIS
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	500	10% discount to BIS
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	500	10% discount to BIS
Cl No. 23.1, 23.2(Identification)	-	500	10% discount to BIS
21.1((f) Oil resistance)	-	500	10% discount to BIS
3.1( Copper Cooduetor)	-	500	10% discount to BIS
3.2(Aluminium conductor)	-	500	10% discount to BIS
4.1(INSULATION : lnsulation for General Service)	-	500	10% discount to BIS
4.2(INSULATION : Heat Resisting insulation)	-	500	10% discount to BIS
4.3(INSULATION : Silicone Rubber Insulation)	-	500	10% discount to BIS
5.1(TAPE : Proofed Tape)	-	500	10% discount to BIS
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	500	10% discount to BIS
5.3(TAPE : Giass Tape)	-	500	10% discount to BIS
6.1(FILLERS : )	-	500	10% discount to BIS
7.1(BRAID : Textile Braid)	-	500	10% discount to BIS
7.2(BRAID : Glass Braid )	-	500	10% discount to BIS
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	500	10% discount to BIS
8.2(SHEATH :Heat Resisting Insulated Cables)	-	500	10% discount to BIS
9.1(PresenRtive Compound)	-	500	10% discount to BIS
9.2(Varnish)	-	500	10% discount to BIS
10( Conductor )	-	500	10% discount to BIS
11(Separator tape)	-	500	10% discount to BIS
12.2(Insulation : Thickness of Insufatien)	-	500	10% discount to BIS
12.4(Insulation : Allplication of Insulation)	-	500	10% discount to BIS
13(CORE IDENTiFICATlON)	-	500	10% discount to BIS
14(Tape)	-	500	10% discount to BIS
15(BRAIDING)	-	500	10% discount to BIS
16(COMPOUNDING AND VARNISHING)	-	500	10% discount to BIS
17(LAYING UP OF CORES)	-	500	10% discount to BIS
18( Binder tape)	-	500	10% discount to BIS
19.2(Sheath : Thickness of Sheath)	-	500	10% discount to BIS
19.4( Sheath :Colour)	-	500	10% discount to BIS
20( Overall diameter)	-	500	10% discount to BIS
21. (a)(Persulphate tests (for copper))	-	500	10% discount to BIS
21. (b)(Annealing Test (for coper))	-	500	10% discount to BIS
21. (c)( Tensile Test (for aluminium))	-	500	10% discount to BIS
21. (d)( Wrapping Test (for aluminium))	-	500	10% discount to BIS
21. (e)(Conductor Resistance )	-	500	10% discount to BIS
21.1( Tensile strength )	-	500	10% discount to BIS
22.1( Elongation)	-	500	10% discount to BIS
21.1(type test : Ageing In air oven)	-	500	10% discount to BIS
21.1(type test : Ageing in air bomb)	-	500	10% discount to BIS
21.1(type test : Ageing In oxygen bomb)	-	500	10% discount to BIS
21.1(type test : Hot set elongation)	-	500	10% discount to BIS
21.1(type test : Tear resistance )	-	500	10% discount to BIS
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	500	10% discount to BIS
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	500	10% discount to BIS
21(Water absorption test)	-	500	10% discount to BIS
23(identification)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Elongation)	-	500	10% discount to BIS
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	500	10% discount to BIS
Cl No. 22.2(High Voltage Test (Water Immersion))	-	500	10% discount to BIS
Cl No. 4.1(Insulation resistance)	-	500	10% discount to BIS
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	500	10% discount to BIS
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	500	10% discount to BIS
Cl No. 23.1, 23.2(Identification)	-	500	10% discount to BIS
21.1((f) Oil resistance)	-	500	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 11-09-2024.

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	500	10% discount to BIS
7.1 Table-1(Dimensional measurement of wires)	-	500	10% discount to BIS
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	500	10% discount to BIS
8.1(Joints in wires-Conductors Containing Seven Wires)	-	500	10% discount to BIS
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	500	10% discount to BIS
9.1(Stranding)	-	500	10% discount to BIS
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	10% discount to BIS
9.3(Direction of Lay)	-	500	10% discount to BIS
9.4(Multiple layers of wires)	-	500	10% discount to BIS
11(Packing and Marking)	-	500	10% discount to BIS
12.2 Table 1(Breaking Load Test- Before Stranding)	-	500	10% discount to BIS
12.2 Table 1(Breaking Load Test- After Stranding)	-	500	10% discount to BIS
12.3 Table 1(Elongation Test- Before Stranding)	-	500	10% discount to BIS
12.3 Table 1(Elongation Test- After Stranding)	-	500	10% discount to BIS
12.4 Table 1(Resistance of Aluminium wire)	-	500	10% discount to BIS
9.2(Lay Ratio 24 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 18 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 12 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 3/6 wire layer)	-	500	10% discount to BIS
7.2.1(Sizes)	-	500	10% discount to BIS
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	500	10% discount to BIS
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	500	10% discount to BIS
6.1(Freedom from Defects)	-	500	10% discount to BIS
7.1 Table-1(Dimensional measurement of wires)	-	500	10% discount to BIS
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	500	10% discount to BIS
8.1(Joints in wires-Conductors Containing Seven Wires)	-	500	10% discount to BIS
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	500	10% discount to BIS
9.1(Stranding)	-	500	10% discount to BIS
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	10% discount to BIS
9.3(Direction of Lay)	-	500	10% discount to BIS
9.4(Multiple layers of wires)	-	500	10% discount to BIS
11(Packing and Marking)	-	500	10% discount to BIS
12.2 Table 1(Breaking Load Test- Before Stranding)	-	500	10% discount to BIS
12.2 Table 1(Breaking Load Test- After Stranding)	-	500	10% discount to BIS
12.3 Table 1(Elongation Test- Before Stranding)	-	500	10% discount to BIS
12.3 Table 1(Elongation Test- After Stranding)	-	500	10% discount to BIS
12.4 Table 1(Resistance of Aluminium wire)	-	500	10% discount to BIS
9.2(Lay Ratio 24 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 18 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 12 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 3/6 wire layer)	-	500	10% discount to BIS
7.2.1(Sizes)	-	500	10% discount to BIS
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	500	10% discount to BIS
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	500	10% discount to BIS
6.1(Freedom from Defects)	-	500	-
7.1 Table-1(Dimensional measurement of wires)	-	500	10% discount to BIS
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	500	10% discount to BIS
8.1(Joints in wires-Conductors Containing Seven Wires)	-	500	10% discount to BIS
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	500	10% discount to BIS
9.1(Stranding)	-	500	10% discount to BIS
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	10% discount to BIS
9.3(Direction of Lay)	-	500	10% discount to BIS
9.4(Multiple layers of wires)	-	500	10% discount to BIS
11(Packing and Marking)	-	500	10% discount to BIS
12.2 Table 1(Breaking Load Test- Before Stranding)	-	500	10% discount to BIS
12.2 Table 1(Breaking Load Test- After Stranding)	-	500	10% discount to BIS
12.3 Table 1(Elongation Test- Before Stranding)	-	500	10% discount to BIS
12.3 Table 1(Elongation Test- After Stranding)	-	500	10% discount to BIS
12.4 Table 1(Resistance of Aluminium wire)	-	500	10% discount to BIS
9.2(Lay Ratio 24 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 18 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 12 wire layer)	-	500	10% discount to BIS
9.2(Lay Ratio 3/6 wire layer)	-	500	10% discount to BIS
7.2.1(Sizes)	-	500	10% discount to BIS
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	500	10% discount to BIS
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	500	10% discount to BIS
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	500	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 11-09-2024.

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	500	10% discount to BIS
12.3, Table-1(Breaking load before stranding)	-	500	10% discount to BIS
12.3, Table-1(Breaking load after stranding)	-	500	10% discount to BIS
12.4(Wrapping test)	-	500	10% discount to BIS
12.5, Table 1(Resistance test)	-	500	10% discount to BIS
12.6, Table 3(Measurement of lay ratio)	-	500	10% discount to BIS
9.3(Stranding)	-	500	10% discount to BIS
6(Freedom from defects)	-	500	10% discount to BIS
7.2.1(Sizes)	-	500	10% discount to BIS
8, 8.1, 8.2(Joint in wires, except during stranding)	-	500	10% discount to BIS
9.2(Lay ratio)	-	500	10% discount to BIS
9.4(Multiple layer of wires)	-	500	10% discount to BIS
4.1(Resistivity)	-	500	10% discount to BIS
4.2(Density)	-	500	10% discount to BIS
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	500	10% discount to BIS
4.4(Coefficient of Linear Expansion)	-	500	10% discount to BIS
5(Material)	-	500	10% discount to BIS
7.1.1(Nominal Sizes)	-	500	10% discount to BIS
7.2.2(Resistance)	-	500	10% discount to BIS
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	500	10% discount to BIS
12.3, Table-1(Breaking load before stranding)	-	500	10% discount to BIS
12.3, Table-1(Breaking load after stranding)	-	500	10% discount to BIS
12.4(Wrapping test)	-	500	10% discount to BIS
12.5, Table 1(Resistance test)	-	500	10% discount to BIS
12.6, Table 3(Measurement of lay ratio)	-	500	10% discount to BIS
9.3(Stranding)	-	500	10% discount to BIS
6(Freedom from defects)	-	500	10% discount to BIS
7.2.1(Sizes)	-	500	10% discount to BIS
8, 8.1, 8.2(Joint in wires, except during stranding)	-	500	10% discount to BIS
9.2(Lay ratio)	-	500	10% discount to BIS
9.4(Multiple layer of wires)	-	500	10% discount to BIS
4.1(Resistivity)	-	500	10% discount to BIS
4.2(Density)	-	500	10% discount to BIS
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	500	10% discount to BIS
4.4(Coefficient of Linear Expansion)	-	500	10% discount to BIS
5(Material)	-	500	10% discount to BIS
7.1.1(Nominal Sizes)	-	500	10% discount to BIS
7.2.2(Resistance)	-	500	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 11-09-2024.

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	1000	10% discount to BIS
4.2(Messenger (Neutral Conductor or Otherwise))	-	1000	10% discount to BIS
5.1(Insulation)	-	1000	10% discount to BIS
6.1(Flexibility class)	-	1000	10% discount to BIS
6.2(Compactness)	-	1000	10% discount to BIS
6.2(Surface)	-	1000	10% discount to BIS
6.2(No of strands)	-	1000	10% discount to BIS
6.3(Protective barrier)	-	1000	10% discount to BIS
6.4(size of street lighting conductor)	-	1000	10% discount to BIS
6.5(Size of messenger conductor )	-	1000	-
6.6(Joints in messenger conductor )	-	1000	10% discount to BIS
6.6(Direction of outer layer)	-	1000	10% discount to BIS
7.1(Insulation)	-	1000	10% discount to BIS
7.2( Thickness of insulation)	-	1000	10% discount to BIS
7.3(Tolerance on thickness of insulation )	-	1000	10% discount to BIS
7.4(Aplication of the insulation )	-	1000	10% discount to BIS
7.5(Colour of the insulation )	-	1000	10% discount to BIS
8.1(Core identification)	-	1000	10% discount to BIS
8.2(Core identification)	-	1000	10% discount to BIS
8.3(Identification by other means)	-	1000	10% discount to BIS
9.1(Assembly (Laying up))	-	1000	10% discount to BIS
9.2(Assembly (Laying up))	-	1000	10% discount to BIS
9.3(Direction of lay)	-	1000	10% discount to BIS
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	1000	10% discount to BIS
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	1000	10% discount to BIS
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	10% discount to BIS
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	10% discount to BIS
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	10% discount to BIS
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	1000	10% discount to BIS
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	1000	10% discount to BIS
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	1000	10% discount to BIS
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	1000	10% discount to BIS
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	1000	10% discount to BIS
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	10% discount to BIS
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	10% discount to BIS
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	1000	10% discount to BIS
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	1000	10% discount to BIS
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	1000	10% discount to BIS
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	1000	10% discount to BIS
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	1000	10% discount to BIS
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1000	10% discount to BIS
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	1000	10% discount to BIS
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	1000	10% discount to BIS
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	1000	10% discount to BIS
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	1000	10% discount to BIS
10.1 g)(High voltage test - IS10810:Part 45)	-	1000	10% discount to BIS
11.4(Bending Test on the Completed Cable ( Optional) )	-	1000	10% discount to BIS
11.4(Bending Test on the Completed Cable ( Optional))	-	1000	10% discount to BIS
10.1 d) iii)(Carbon Black Content)	-	1000	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 11-09-2024.

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	1000	10% discount to BIS
4.1.1(INSULATION : General Purjose Insulaiion)	-	1000	10% discount to BIS
4.1.2(INSULATION : Heat Resisting Insulation)	-	1000	10% discount to BIS
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	1000	10% discount to BIS
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	1000	10% discount to BIS
6.1(MATERIALS : ARMGURING)	-	1000	10% discount to BIS
6.2(MATERIALS : ARMGURING)	-	1000	10% discount to BIS
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	1000	10% discount to BIS
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	1000	10% discount to BIS
8.1(CONSTRUCTION : CONDUCTOR)	-	1000	10% discount to BIS
8.2(CONSTRUCTION : CONDUCTOR)	-	1000	10% discount to BIS
9.1(INSULATION )	-	1000	10% discount to BIS
9.2(INSULATION : Thickness of Insulation)	-	1000	10% discount to BIS
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	1000	10% discount to BIS
9.4(INSULATION : Application of Insulation)	-	1000	10% discount to BIS
10.1(CORE IDENTIFICATION)	-	1000	10% discount to BIS
10.2(CORE IDENTIFICATION)	-	1000	10% discount to BIS
10.3(CORE IDENTIFICATION)	-	1000	10% discount to BIS
10.3.1(Arrangement of Marking)	-	1000	10% discount to BIS
11.1(LAYING UP OF CORES)	-	1000	10% discount to BIS
11.2(LAYING UP OF CORES)	-	1000	10% discount to BIS
12.1(INNER SHEATH)	-	1000	10% discount to BIS
12.2(INNER SHEATH)	-	1000	10% discount to BIS
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	1000	10% discount to BIS
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	1000	10% discount to BIS
13.1.1(ARMOURING : Application)	-	1000	10% discount to BIS
13.1.2(Armouring: Coverage )	-	1000	10% discount to BIS
13.1.3(ARMOURING : Direction of lay )	-	1000	10% discount to BIS
13.1.4(ARMOURING : Application)	-	1000	10% discount to BIS
13.2(ARMOURING : Type of Armour)	-	1000	10% discount to BIS
13.2.1(ARMOURING : Type of Armour)	-	1000	10% discount to BIS
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	10% discount to BIS
13.3(Armouring : Dimensions -Formed wire )	-	1000	10% discount to BIS
13.4(ARMOURING : Joints)	-	1000	10% discount to BIS
13.5.1(ARMOURING : Resistance)	-	1000	10% discount to BIS
13.5.2(ARMOURING : Resistance)	-	1000	10% discount to BIS
13.6 a)(ARMOURING: Tensile Strength)	-	1000	10% discount to BIS
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	10% discount to BIS
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	10% discount to BIS
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	10% discount to BIS
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	10% discount to BIS
13.6 g)(ARMOURING: Resistivity)	-	1000	10% discount to BIS
13.6 b)(ARMOURING: Elongation )	-	1000	10% discount to BIS
14.1(OUTER SHEATH)	-	1000	10% discount to BIS
14.2(OUTER SHEATH)	-	1000	10% discount to BIS
14.3(OUTER SHEATH : Colour )	-	1000	10% discount to BIS
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	1000	10% discount to BIS
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	1000	10% discount to BIS
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	1000	10% discount to BIS
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	10% discount to BIS
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	1000	10% discount to BIS
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	1000	10% discount to BIS
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	1000	10% discount to BIS
15.1 a) 4)(Resistance test - Neutral conductor )	-	1000	10% discount to BIS
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	1000	10% discount to BIS
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	1000	10% discount to BIS
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	1000	10% discount to BIS
15.1 d)1)(Physical tests for sheath : Elongation )	-	1000	10% discount to BIS
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	1000	10% discount to BIS
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	1000	10% discount to BIS
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	10% discount to BIS
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	10% discount to BIS
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1000	10% discount to BIS
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1000	10% discount to BIS
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	10% discount to BIS
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	10% discount to BIS
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	1000	10% discount to BIS
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	10% discount to BIS
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	1000	10% discount to BIS
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	10% discount to BIS
15.1 d)4)(Hot deformation : Insulation )	-	1000	10% discount to BIS
15.1 d)4)(Hot deformation : Sheath )	-	1000	10% discount to BIS
15.1 d)5)( Loss of mass in air oven- Insulation )	-	1000	10% discount to BIS
15.1 d)5)( Loss of mass in air oven- sheath )	-	1000	10% discount to BIS
15.1 d)6)(Heat shock test- Insulation )	-	1000	10% discount to BIS
15.1 d)6)(Heat shock test- sheath )	-	1000	10% discount to BIS
15.1 d)7)(Thermal stability- insulation )	-	1000	10% discount to BIS
15.1 d)7)(Thermal stability- Sheath )	-	1000	10% discount to BIS
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1000	10% discount to BIS
15.1 e)(Insulation resistance test : IR Constant )	-	1000	10% discount to BIS
15.1 f)(High voltage test ( water immersion test ))	-	1000	10% discount to BIS
15.1 g)(High voltage test at room temperature)	-	1000	10% discount to BIS
15.1 g)(High voltage test at room temperature)	-	1000	10% discount to BIS
15.4 a)(Cold bend test- Insulation ( Optional test))	-	1000	10% discount to BIS
15.4 a)(Cold bend test- Sheath ( Optional test))	-	1000	10% discount to BIS
15.4 b)(Cold impact test- Insulation ( Optional test))	-	1000	10% discount to BIS
15.4 b)(Cold impact test- Sheath ( Optional test))	-	1000	10% discount to BIS
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	1000	10% discount to BIS
16.1(DETAILS OF TESTS : General)	-	1000	10% discount to BIS
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	1000	10% discount to BIS
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1000	10% discount to BIS
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1000	10% discount to BIS
16.4(Flammability Test)	-	1000	10% discount to BIS
16.5(Oxygen Index Test)	-	1000	10% discount to BIS
16.6(Flame Retardance Test on Single Cables)	-	1000	10% discount to BIS
16.7(Flame Retardance Test on Bunched Cables)	-	1000	10% discount to BIS
16.9(Test for Halogen Acid Gas Evolution)	-	1000	10% discount to BIS
16.1(Temperature Index)	-	1000	10% discount to BIS
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	1000	10% discount to BIS
17.2.1(IDENTIFICATION : Cable Identification)	-	1000	10% discount to BIS
17.2(IDENTIFICATION : Cable Identification)	-	1000	10% discount to BIS
17.3(IDENTIFICATION : Cable Code)	-	1000	10% discount to BIS
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	1000	10% discount to BIS
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	1000	10% discount to BIS
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	1000	10% discount to BIS
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	10% discount to BIS
16.4(Flammability Test- Un affected portion)	-	1000	10% discount to BIS
16.4(Flammability Test- Period of Burning)	-	1000	10% discount to BIS
9.3(Minimum Thickness of Reduce core insulation)	-	1000	10% discount to BIS
9.2(Thickness of Reduce core insulation)	-	1000	10% discount to BIS
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	1000	10% discount to BIS
Cl No. 16.10(Smoke density test)	-	1000	10% discount to BIS
Cl No. 16.8(Test for specific optical density of smoke)	-	1000	10% discount to BIS
Table 4(Copper purity test)	-	1000	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 11-09-2024.

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	1000	10% discount to BIS
6(ARMOURING)	-	1000	10% discount to BIS
7(OUTER SHEATH)	-	1000	10% discount to BIS
8.1(CONDUCTOR: CONSTRUCTION)	-	1000	10% discount to BIS
5.1(FILLER AND INNER SHEATH)	-	1000	10% discount to BIS
5.2(FILLER AND INNER SHEATH)	-	1000	10% discount to BIS
8.2(PROTECTIVE BARRIER)	-	1000	10% discount to BIS
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	1000	10% discount to BIS
9.1(Insulation Applied by extrusicn)	-	1000	10% discount to BIS
9.2(Thickness of Insulation - Average)	-	1000	10% discount to BIS
9.3(Thickness of Insulation - Minimum)	-	1000	10% discount to BIS
9.4(Application of Insulation)	-	1000	-
10.1(Core Identification)	-	1000	10% discount to BIS
10.2(Core Identification- Neutral)	-	1000	10% discount to BIS
10.3(Core Identification by number )	-	1000	10% discount to BIS
10.4(Core Identification by number - Neutral )	-	1000	10% discount to BIS
11(LAVING UP OF CORES)	-	1000	10% discount to BIS
12.1 & 12.2(Inner sheath : Application)	-	1000	10% discount to BIS
12.3(Thickness of Inner Sheath)	-	1000	10% discount to BIS
13.1(Armouring: Application)	-	1000	10% discount to BIS
13.1.2(Armouring: Coverage )	-	1000	10% discount to BIS
13.1.3(Armouring: Direction of Lay )	-	1000	10% discount to BIS
13.2(Type of armour )	-	1000	10% discount to BIS
13.3(Armouring : Dimensions -Wire Diameter)	-	1000	10% discount to BIS
13.3(Armouring : Dimensions -Formed wire )	-	1000	10% discount to BIS
13.4(Armour: Joint)	-	1000	10% discount to BIS
13.5(Armouring : Resistance Test)	-	1000	10% discount to BIS
13.6 a)(ARMOURING: Tensile Strength)	-	1000	10% discount to BIS
13.6 b)(ARMOURING: Elongation )	-	1000	10% discount to BIS
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	10% discount to BIS
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	10% discount to BIS
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	10% discount to BIS
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	10% discount to BIS
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	1000	-
14.2(Colour of outer sheath)	-	1000	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-
14.3(Thickness of outer sheath - minimum)	-	1000	10% discount to BIS
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	10% discount to BIS
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	10% discount to BIS
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	10% discount to BIS
15.1 a) iii)(Wrapping test (for aluminium))	-	1000	10% discount to BIS
15.1 a) iv)(Resistance test - Main conductor)	-	1000	10% discount to BIS
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	10% discount to BIS
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	10% discount to BIS
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	10% discount to BIS
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	1000	10% discount to BIS
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	1000	10% discount to BIS
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	10% discount to BIS
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	10% discount to BIS
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	10% discount to BIS
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	1000	10% discount to BIS
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	1000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	1000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	1000	10% discount to BIS
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	1000	10% discount to BIS
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	10% discount to BIS
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	10% discount to BIS
15.1 e) v) (Sheath : Hot deformation)	-	1000	10% discount to BIS
15.1 e) vi) (Sheath : Heat shock test)	-	1000	10% discount to BIS
15.1 e) vii) (Sheath : Thermalstability)	-	1000	10% discount to BIS
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	10% discount to BIS
16.2(HIGH VOLTAGE TEST )	-	1000	10% discount to BIS
16.3(FLAMMABILITY TEST : Period of Burning )	-	1000	10% discount to BIS
16.3(FLAMMABILITY TEST : Unaffected length )	-	1000	10% discount to BIS
16.9(Oxygen Index Test)	-	1000	10% discount to BIS
16.1(Flame Retardance Test on Single Cables)	-	1000	10% discount to BIS
16.11(Flame Retardance Test on Bunched Cables)	-	1000	10% discount to BIS
16.13(Test for Halogen Acid Gas Evolution)	-	1000	10% discount to BIS
16.14(Temperature Index)	-	1000	10% discount to BIS
17.1(Manufacturer'. identification)	-	1000	10% discount to BIS
17.2(cable Indentification )	-	1000	10% discount to BIS
17.3(cable Code )	-	1000	10% discount to BIS
15.4 (a)(Cold bend)	-	1000	10% discount to BIS
15.4 (b)(Cold impact)	-	1000	10% discount to BIS
Table 1(Ageing in air oven - Elongation on Insulation)	-	1000	10% discount to BIS
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	1000	10% discount to BIS
Table 1(Ageing in air oven - Elongation on Insulation)	-	1000	10% discount to BIS
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	1000	10% discount to BIS
Table 4(Copper purity test)	-	1000	10% discount to BIS
Cl No. 16.15(Smoke density test)	-	1000	10% discount to BIS
Table 2(Cold Impact test for Outer sheath)	-	1000	10% discount to BIS
Table 2(Cold bend test for Outer sheath)	-	1000	10% discount to BIS
Cl 16(Halogen Acid Gas Test)	-	1000	10% discount to BIS
Cl 16(Halogen Acid Gas Test)	-	1000	10% discount to BIS
Cl 16(Halogen Acid Gas Test)	-	1000	10% discount to BIS
4(INSULATION : MATERIALS)	-	1000	10% discount to BIS
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	1000	10% discount to BIS

07 Sep, 2026

-
Included w.e.f. 11-09-2024.

Bureau of Indian Standards

The National Standards Body of India

IEC TEST LABS LLP

Ground Floor, Plot No. N-47, Pkt-N, Sector-5, Bawana, DSIDC, Delhi-110039, Delhi, North West, Delhi, 110039

9871727340 iectestlabs@gmail.com

Scope List