BIS - LIMS (Laboratory Information Management System)

AANKAN CALIBRATION AND TESTING CENTRE LLP, DANTLI

PLOT NO. B, LS NO. 193, DANTALI, Gandhinagar, Gujarat, 382721

9879564686 aankan.act@gmail.com

Scope List

Reset

44 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

PE 63, 80, 100 PN 2 to 20 DN 16 to 400 SDR 41 to 6 mm

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.9 table-6(Elongation at Break)	-	1900	OK
8.8(Tensile Strength for Butt-fusion)	-	9500	OK
8.7(Density)	-	950	OK
8.2(Longitudinal Reversion Test)	-	1900	OK
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1899	OK
7.4.1.2(Ovality)	-	475	OK
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	950	OK
7.2(Length)	-	475	OK
6.2.1(6.1.1 Identification Stripes)	-	950	OK
6.2(Colour)	-	475	OK
6.1.4(PIPE DESCRIPTION)	-	0	THIS IS NOT A TEST
8.6(Overall migration)	-	4750	OK
5.3(d)(Carbon Black Master Batch)	-	0	NIL
5.3(c)(Carbon Black Master Batch)	-	0	NIL
5.3(b)(Carbon Black Master Batch)	-	0	NIL
5.3 (a)(Carbon Black Master Batch)	-	0	NIL
5.2(Polyethylene Resin)	-	4750	OK
8.3(Carbon black)	-	1425	OK
5.3(e)(Carbon Black Master Batch)	-	0	NIL
6, 6.1(PIPE DESCRIPTION)	-	0	THIS IS NOT A TEST
5.4(Anti oxydent)	-	0	NIL
5.2(Density)	-	950	OK
5.2(MFI @ 1900C/5.0 Kg)	-	1425	OK
5.2(Volatile matter Content)	-	1000	OK
5.3(Toluene Extract)	-	1375	OK
Clause 7.1(Visual Apperance)	-	0	OK
Clause 8.3(Carbon Black content)	-	1425	OK
Clause 8.3(Carbon Black Dispersion)	-	1425	OK
Clause 8.6(Overall migration (stimulate))	-	4750	OK
7.1(Visual Appearance)	-	0	OK
Cl. 8.3(Carbon Black Content)	-	1425	OK
5.2,T2(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1425	OK
8.7(Density-IS 7328:2020)	-	950	OK
8.9,T6("Tensile - IS 4984-2016 (Annexure-H)")	-	1900	OK
8.9,T6("Elongation -IS 4984-2016 (Annexure-H)")	-	1900	OK
Cl 8.3(Carbon Black Content)	-	1425	OK
Cl 8.3(Carbon Black Dispersion)	-	1425	OK
Clause 8.6(Overall migration (surface of material))	-	4750	OK
7.3(Coiling)	-	0	OK
Table-2 (iii, iv)(Thermal Stability (Oxidation Induction Time), Volatile Matter)	-	4000	OK
Cl. 8.3(Carbon Black Dispersion)	-	1425	OK
8.10(Slow Crack Growth Rate)	-	9500	OK
6.1.3 (PIPE DESCRIPTION)	-	0	NOT A TEST
6, 6.1.2(PIPE DESCRIPTION)	-	0	NOT A TEST
6, 6.1.1(PIPE DESCRIPTION)	-	0	NOT A TEST
5, 5.1 table-1(MATERIALS)	-	4750	OK
Clause 7.3(Coiling)	-	0	NOT A TEST
7()	-	0	NOT A TEST

-
-

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

Class 1/2/3, SDR:11/13.5/17, Nominal size:15 to 150 mm

99500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table 1(Classification of pipes)	-	0	NOT A TEST
6.3.1 Annex B(Chloride content)	-	2000	RESIN (Chloride content)TESTING CHARGE Rs 2000/- Compound (Chloride content)TESTING CHARGE Rs 2000/-
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	7500	(Verification of the Malfunction) TESTING CHARGE Rs 7500/-
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	12000	(compound properties testing )TESTING CHARGE Rs 12000/-
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	3000	(Dimension of Pipe)TESTING CHARGE Rs 3000/-
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	3000	(Dimension of Pipe)TESTING CHARGE Rs 3000/-
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	3000	(Dimension of Pipe)TESTING CHARGE Rs 3000/-
7.1.3 (Effective length)	-	3000	(Dimension of Pipe)TESTING CHARGE Rs 3000/-
8(Pipe Ends)	-	3000	(Dimension of Pipe)TESTING CHARGE Rs 3000/-
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	0	OK
9.1(Visual Appearance)	-	500	(Visual Appearance) TESTING CHARGE Rs 500/-
9.1(Visual Appearance)	-	0	repeat
9.2 IS 12235 (Part 3)(Opacity)	-	2500	(Opacity) TESTING CHARGE Rs 2500/-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	5000	(Effect on water ) TESTING CHARGE Rs 5000/-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	5000	(Effect on water ) TESTING CHARGE Rs 5000/-
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	5000	(Effect on water ) TESTING CHARGE Rs 5000/-
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	5000	(Effect on water ) TESTING CHARGE Rs 5000/-
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	5000	(Effect on water ) TESTING CHARGE Rs 5000/-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	5000	(Effect on water ) TESTING CHARGE Rs 5000/-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	repeat
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	3000	(Reversion Test) TESTING CHARGE Rs 3000/-
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	3000	(Vicat Softening Temperature ) TESTING CHARGE Rs 3000
9.6 IS 12235(Part 14)(Density)	-	2000	(Density) TESTING CHARGE Rs 2000/-
10(Mechanical Properties)	-	0	OK
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	2999.97	(Hydrostatic Characteristics) 1 Hr TESTING CHARGE Rs 3000/-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	5000	(Hydrostatic Characteristics) 165 Hr TESTING CHARGE Rs 5000/-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	7000	(Hydrostatic Characteristics) 1000 Hr TESTING CHARGE Rs 7000
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	35000	(Thermal Stability by Hydrostatic Pressure Testing) TESTING CHARGE Rs 35000/-
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	3000	(Resistance to External Blow at O°C) TESTING CHARGE Rs 3000/-
10.4 IS 12235(Part 19)(Flattening Test)	-	3000	(Flattening Test) TESTING CHARGE Rs 3000/-
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	3000	(Tensile Strength) TESTING CHARGE Rs 3000
5 Table 1(Classification of pipes)	-	0	OK
6.2.1 Annex B(Chloride Content of Resin)	-	0	repeat
6.3(Compound Properties)	-	12000	(Compound Properties) testing charge 12000/-
6.3.1 Annex B(Chloride content)	-	0	repeat
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	0	repeat
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	0	repeat
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	0	repeat
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	0	repeat
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	0	repeat
7.1.3 (Effective length)	-	0	repeat
8.0(Pipe Ends)	-	0	repeat
9.0(PHYSICAL AND 1CHARACTERISTICS)	-	0	repeat
9.1(Visual Appearance)	-	0	repeat
9.1(Visual Appearance)	-	0	repeat
9.2 IS 12235 (Part 3)(Opacity)	-	0	repeat
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	0	repeat
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	repeat
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	repeat
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	repeat
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	repeat
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	repeat
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	repeat
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	0	repeat
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	0	repeat
9.6 IS 12235(Part 14)(Density)	-	0	repeat
10.0(Mechanical Properties)	-	0	repeat
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	repeat
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	repeat
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	repeat
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	0	repeat
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	0	repeat
10.4 IS 12235(Part 19)(Flattening Test)	-	0	repeat
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	0	repeat
7.1.2(Wall Thickness (Maximum))	-	0	repeat
7.1.1(Outside Diameter at any point (Maximum))	-	0	repeat
6.3(K value Test)	-	3000	ok
6.3.3(Density)	-	0	repeat

-
-

IS 10701 (2012)

Structural plywood - Specification (First Revision)

ALL

17650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.3(Glue Shear strength in dry state)	-	1000	20% DISCOUNT FOR BIS GSTIN EXTRA AS PER GOVT RULE
11.4.1(Resistance to Water)	-	2500	-
11.4.2(Resistance to Water)	-	2500	-
11.5(Resistance to Micro-organisms)	-	2800	-
11.6(Tensile Strength)	-	1000	-
11.7.1(Compressive Strength, Bending Strength, Panel Shear Strength, Plate Shear Strength and Rolling Shear Strngth)	-	3000	-
11.8(Wet Bending Strength)	-	2000	-
Clause 11.2(Moisture content)	-	400	-
Cl-8(Dimension and tolerances)	-	1200	-
Cl-9(Workmanship and finish)	-	100	-
Cl-7.1(Veneers)	-	200	-
Cl-7.2(Construction)	-	200	-
Cl-11.9(Retention of preservatives)	-	3000	-
Cl-4(Material)	-	0	CL.4 ADHESIVE EXTRA CHARGES
Cl-5(Plywood)	-	0	-
Clause. 7.3(Consruction Inclination)	-	0	-
Clause. 7.4(Moisture content)	-	400	-
Cl-8.2(Thicnkess)	-	200	-
Cl-8.3.1(Length)	-	200	-
Cl-8.3.1(width)	-	200	-
Cl-8.3.1(Tolerances- Thickness)	-	200	-
Cl-8.3.1(Edge Straightness)	-	200	-
Cl-8.3.1(Squareness)	-	200	-
Cl-11.6, Table-3 (i)((Modulus of Rupture: Across the Face Grain: Min Ind.))	-	1500	-
Cl-11.8, Table-4((Modulus of Rupture: Across the Face Grain: Avg))	-	1500	-
Cl-11.8, Table-4((Modulus of Rupture: Along the Face Grain: Min Ind))	-	1500	-
Cl-11.8, Table-4(Modulus of Rupture: Along the Face Grain: Avg))	-	1500	-
Cl-11.8, Table-4(Modulus of Elasticity: Across the Face Grain: Min Ind)	-	1500	-
Cl-11.8, Table-4((Modulus of Elasticity: Across the Face Grain: Avg))	-	1500	-
Cl-11.8, Table-4((Modulus of Elasticity: Along the Face Grain: Min Ind))	-	1500	-

-
Included w.e.f 24.03.2026

IS 14616 (1999)

Laminated veneer lumber specification

all

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Dimensions)	-	200	-
6.2(Dimensions)	-	200	-
7(workmanship and finish)	-	600	-
8.2.1(moisture content)	-	800	-
8.2.2(adhesion of plies)	-	1500	-
8.2.3, 8.2.4, Table-1(modulus of rupture)	-	1500	-
8.2.3, 8.2.4, Table-1(modulus of elasticity)	-	1500	-
8.2.3, 8.2.4, Table-1(compressive strength parallel to grain)	-	1500	-
8.2.3, 8.2.4, Table-1(horizontal shear a)-parallel to grain ,b)-perpendicular to grain)	-	3000	-
8.2.3, 8.2.4, Table-1(tensile strength parallel to grain )	-	2000	-
8.2.3, 8.2.4, Table-1(screw holding power a)-parallel to grain ,b)-perpendicular to grain)	-	2000	-
8.2.3, 8.2.4, Table-1(thickness swelling in 2 hrs. water soaking)	-	1000	-
8.2.4(swelling in wear)	-	1000	-
Clause 8.2.1(Moisture content)	-	800	-

-
Included w.e.f 09.06.2026

IS 14276 (2016)

Cement bonded particle boards - Specification (First Revision)

ALL

14400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Finish)	-	400	-
7(Dimensions and Tolerances)	-	600	-
8.5(Workability)	-	500	-
10.3, Table-1(Test for Density)	-	600	-
10.5, Table-1(Test for Water Absorption)	-	1200	-
10.6, Table-1(Test for swelling in water)	-	2000	-
10.7, Table-1(Test for modulus of Rupture)	-	1500	-
10.8, Table-1(Test for modulus of Elasticity)	-	1500	-
10.9, Table-1(Test for tensile strength perpendicular to Surface)	-	3500	-
10.1, Table-1(Test for Screw Withdrawal Strength)	-	2000	-
Clause 8.2 Table 1(Moisture content)	-	600	-
6(Finish)	-	0	-
7(Dimensions and Tolerances)	-	0	-
8.5(Workability)	-	0	-
10.3, Table-1(Test for Density)	-	0	-
10.5, Table-1(Test for Water Absorption)	-	0	-
10.6, Table-1(Test for swelling in water)	-	0	-
10.7, Table-1(Test for modulus of Rupture)	-	0	-
10.8, Table-1(Test for modulus of Elasticity)	-	0	-
10.9, Table-1(Test for tensile strength perpendicular to Surface)	-	0	-
10.1, Table-1(Test for Screw Withdrawal Strength)	-	0	-
Clause 8.2 Table 1(Moisture content)	-	0	-
6(Finish)	-	0	-
7(Dimensions and Tolerances)	-	0	-
8.5(Workability)	-	0	-
10.3, Table-1(Test for Density)	-	0	-
10.5, Table-1(Test for Water Absorption)	-	0	-
10.6, Table-1(Test for swelling in water)	-	0	-
10.7, Table-1(Test for modulus of Rupture)	-	0	-
10.8, Table-1(Test for modulus of Elasticity)	-	0	-
10.9, Table-1(Test for tensile strength perpendicular to Surface)	-	0	-
10.1, Table-1(Test for Screw Withdrawal Strength)	-	0	-
Clause 8.2 Table 1(Moisture content)	-	0	-

-
Included w.e.f. 03.06.2026

IS 15786 (2008)

Prelaminated cement bonded particle board - Specification

ALL

32900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 10.3 (Moisture content)	-	600	IS 15786 physical tests-15500, Raw material cl. 5.2, 5.3, 5.4-3000, IS 14276 as per clause 5.1-14400 )
5.1(Cement Bonded Particle Board)	-	14400	-
5.2(Impregnated Base Paper)	-	1000	-
5.4(Finished Foil)	-	0	-
6(Manufacture)	-	0	-
7(Finish)	-	0	-
8(DIMENSIONS AND TOLERANCES)	-	600	-
10.2(Test for Density)	-	600	-
10.4(Test for Water Absorption)	-	1200	-
10.5(Test for Swelling in Water)	-	1000	-
10.6(Test for Modulus of Elasticity and Modulus of Rupture)	-	1000	-
10.7(Test for Tensile Strength Perpendicular to Surface)	-	1000	-
10.8(Test for Tensile Strength Perpendicular to Surface After Ageing)	-	3000	-
10.9(Test for Screw Withdrawal Strength)	-	2000	-
10.10(Test for Abrasion Resistance)	-	1500	-
10.11(Test for Resistance to Steam)	-	600	-
10.12(Test for Resistance to Crack)	-	600	-
10.13(Test for Resistance to Cigarette Bum)	-	600	-
10.14(Test for Resistance to Stain)	-	600	-
11(Marking)	-	0	-
5.3(Impregnated OverlaylUnderIay)	-	1000	Complete Testing Charges IS-32900 (For IS 15786 physical tests-15500, Raw material cl. 5.2, 5.3, 5.4-3000, IS 14276 as per clause 5.1-14400 )

-
Included w.e.f 01.04.2026

IS 15380 (2023)

MOULDED HIGH DENSITY FIBRE HDF PANELLED DOOR SHUTTERS - SPECIFICATION ( First Revision )

all

25500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Sized)	-	0	EXTRA CHARGE FOR RAW MATERIAL TESTING 5000/-
Cl-6.1.2(Moisture content in timbers)	-	0	-
Cl-6.2 S.No (1), i(Density, kg/m3 , Min)	-	1000	-
Cl-6.2 S.No (1), ii(Moisture content, percent, Max)	-	1000	-
Cl-6.2 S.No (1), iii(Water absorption, percent, Max)	-	2000	-
Cl-6.2 S.No (1), iv(Swelling in water, percent, Max)	-	2000	-
Cl-6.2 S.No (1), v(Modulus of rupture, N/mm2 , Min)	-	1500	RS 1500/-
Cl-6.2 S.No (1), vi(Internal bond strength, N/mm2 , Min)	-	2000.01	-
Cl-6.2 S.No (1), vii(Immersion in boiling water at (100 ± 3) °C for 4 h)	-	2000	-
Cl-6.2 S.No (1), viii(Formaldehyde emission, mg/100 g, Max)	-	3000	FORMALDEHYDE CONTENT TEST -RS 3000/-
Cl- 6.3(Particle Boards as Core)	-	0	-
Cl- 6.4(Adhesive)	-	0	EXTRA
Cl- 6.5(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), Medium Density Fibre (MDF))	-	0	-
Cl-11.1(Dimensions and Squareness Test)	-	1000	11.1(Dimensions - Height) - 200 11.1(Dimensions - Width) - 200 11.1(Dimensions - Thickness) - 200 11.1(Dimensions - Variation in thickness) - 200 11.1(Dimensions - Squareness) - 200
Cl-11.2(General Flatness Test)	-	900	-
Cl-11.3(Local Planeness Test)	-	1000	-
Cl-11.4(Impact Indentation Test)	-	999.99	1000 RS
Cl-11.5(Flexure Test)	-	2000	-
Cl-11.6(Edge Loading Test)	-	1500	-
Cl-11.7(Shock Resistance Test)	-	2000	-
Cl-11.8(Buckling Resistance Test)	-	1500	-
Cl-11.9(Slamming Test)	-	1500	-
Cl-11.10(Misuse Test)	-	800	-
Cl-11.11(Varying Humidity Test)	-	4000	-
Cl-11.12(End Immersion Test)	-	3000	-
Cl-11.13(Glue Adhesion Test)	-	1000	-
Cl-11.14(Screw Withdrawal Resistance Test)	-	3500	-
Cl-12.2(Sample Size)	-	0	-
Cl-14(Marking)	-	0	-
Cl-6.1.1(Bulk density of timber)	-	0	-
Cl-9(Workmanship and finish)	-	199.99	-
Cl-5.1(Sized)	-	0	-
Cl-6.1.2(Moisture content in timbers)	-	0	-
Cl-6.2 S.No (1), i(Density, kg/m3 , Min)	-	0	-
Cl-6.2 S.No (1), ii(Moisture content, percent, Max)	-	0	-
Cl-6.2 S.No (1), iii(Water absorption, percent, Max)	-	0	-
Cl-6.2 S.No (1), iv(Swelling in water, percent, Max)	-	0	-
Cl-6.2 S.No (1), v(Modulus of rupture, N/mm2 , Min)	-	0	-
Cl-6.2 S.No (1), vi(Internal bond strength, N/mm2 , Min)	-	0	-
Cl-6.2 S.No (1), vii(Immersion in boiling water at (100 ± 3) °C for 4 h)	-	0	-
Cl-6.2 S.No (1), viii(Formaldehyde emission, mg/100 g, Max)	-	0	-
Cl- 6.3(Particle Boards as Core)	-	0	-
Cl- 6.4(Adhesive)	-	0	-
Cl- 6.5(Laminated veneer lumber (LVL), veneer laminated lumber (VLL), Medium Density Fibre (MDF))	-	0	-
Cl-11.1(Dimensions and Squareness Test)	-	0	-
Cl-11.2(General Flatness Test)	-	0	-
Cl-11.3(Local Planeness Test)	-	0	-
Cl-11.4(Impact Indentation Test)	-	0	-
Cl-11.5(Flexure Test)	-	0	-
Cl-11.6(Edge Loading Test)	-	0	-
Cl-11.7(Shock Resistance Test)	-	0	-
Cl-11.8(Buckling Resistance Test)	-	0	-
Cl-11.9(Slamming Test)	-	0	-
Cl-11.10(Misuse Test)	-	0	-
Cl-11.11(Varying Humidity Test)	-	0	-
Cl-11.12(End Immersion Test)	-	0	-
Cl-11.13(Glue Adhesion Test)	-	0	-
Cl-11.14(Screw Withdrawal Resistance Test)	-	0	-
Cl-12.2(Sample Size)	-	0	-
Cl-14(Marking)	-	0	-
Cl-6.1.1(Bulk density of timber)	-	0	-
Cl-9(Workmanship and finish)	-	0	-

-
Included w.e.f 05.08.2026

IS 19267 (2025)

Oriented Strand Boards ï¿½ Specification

all

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Wood)	-	0	-
Cl-5.2(Adhesives)	-	0	EXTRA
Cl-5.3(Preservative)	-	0	EXTRA
Cl-7(Finish)	-	500	-
Cl-8.1(Any dimensions (length and width))	-	1000	-
Cl-8.2(Thickness)	-	500	-
Cl-8.3(Squareness and Edge Straightness)	-	1000	-
Cl-8.4(Tolerances)	-	1000	-
Cl-9.1, Table-2 (i)(Density variation within board, Max)	-	1000	-
Cl-9.1, Table-2 (ii)(Moisture content,)	-	1000	-
Cl-9.1, Table-3 (GP-REG) (i)(Modulus of rupture (MoR), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-3 (GP-REG) (ii)(Modulus of rupture (MoR), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-3 (GP-REG) (iii)(Modulus of elasticity (MoE), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-3 (GP-REG) (iv)(Modulus of elasticity (MoE), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-3 (GP-REG) (v)(Internal bond strength, N/mm2, Min)	-	2000	-
Cl-9.1, Table-3 (GP-REG) (vi)(24 h thickness swelling (due to general absorption), percent, Max)	-	1500	-
Cl-9.1, Table-3 (GP-REG) (vii)(Screw withdrawal strength (face), N, Min)	-	1500	-
Cl-9.1, Table-3 (GP-REG) (viii)(Screw withdrawal strength (edge), N, Min)	-	1500	-
Cl-9.1, Table-4 (LB-REG) (i)(Modulus of rupture (MoR), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-4 (LB-REG) (ii)(Modulus of rupture (MoR), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-4 (LB-REG) (iii)(Modulus of elasticity (MoE), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-4 (LB-REG) (iv)(Modulus of elasticity (MoE), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-4 (LB-REG) (v)(Internal bond strength, N/mm2, Min)	-	2000	-
Cl-9.1, Table-4 (LB-REG) (vi)(24 h thickness swelling (due to general absorption), percent, Max)	-	1500	-
Cl-9.1, Table-4 (LB-REG) (vii)(Screw withdrawal strength (face), N, Min)	-	1500	-
Cl-9.1, Table-4 (LB-REG) (viii)(Screw withdrawal strength (edge), N, Min)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (i)(Modulus of rupture (MoR), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (ii)(Modulus of rupture (MoR), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (iii)(Modulus of elasticity (MoE), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (iv)(Modulus of elasticity (MoE), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (v)(Internal bond strength, N/mm2, Min)	-	2000	-
Cl-9.1, Table-5 (LB-MR) (vi)(24 h thickness swelling (due to general absorption), percent, Max)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (vii)(Screw withdrawal strength (face), N, Min)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (viii)(Screw withdrawal strength (edge), N, Min)	-	1500	-
Cl-9.1, Table-5 (LB-MR) (ix) (a)("Option1, Cyclic test: (i) Internal bond Strength, N/mm2, Min")	-	2000	-
Cl-9.1, Table-5 (LB-MR) (ix) (b)("Option 2, Boil test: (i) Internal bond strength, N/mm2, Min")	-	2000	-
Cl-9.1, Table-5 (LB-MR) (x)(Modulus of rupture after cyclic test, N/mm2— Major axis)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (i)(Modulus of rupture (MoR), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (ii)(Modulus of rupture (MoR), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (iii)(Modulus of elasticity (MoE), N/mm2, Min — Major axis)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (iv)(Modulus of elasticity (MoE), N/mm2, Min — Minor axis)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (v)(Internal bond strength, N/mm2, Min)	-	2000	-
Cl-9.1, Table-6 (HLB-MR) (vi)(24 h thickness swelling (due to general absorption), percent, Max)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (vii)(Screw withdrawal strength (face),)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (viii)(Screw withdrawal strength (edge),)	-	1500	-
Cl-9.1, Table-6 (HLB-MR) (ix)("Option1, Cyclic test: (i) Internal bond Strength, N/mm2, Min")	-	2000	-
Cl-9.1, Table-6 (HLB-MR) (ix)("Option 2, Boil test: (i) Internal bond strength, N/mm2, Min")	-	2000	-
Cl-9.1, Table-6 (HLB-MR) (x)(Modulus of rupture after cyclic test, N/mm2 — Major axis)	-	1500	-
Cl-9.1, Table-7 (i)(Formaldehyde content Fc, mg/100 g for oven dry board)	-	3000	-
Cl-9.1, Table-7 (ii)(Steady-state formaldehyde emission, Fc, mg/m3)	-	0	-
Cl-11(Marking)	-	0	-

-
Included w.e.f 17.03.2026

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

UPTO 355 mm

35500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	15000	Rs 35500 for Pipe, 15000 Extra for Raw material Testing
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	15000	15000 Extra for Raw material Testing
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	15000	15000 Extra for Raw material Testing
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	15000	15000 Extra for Raw material Testing
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	15000	15000 Extra for Raw material Testing
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	15000	15000 Extra for Raw material Testing
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	15000	15000 Extra for Raw material Testing
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	15000	15000 Extra for Raw material Testing
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	15000	15000 Extra for Raw material Testing
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	15000	15000 Extra for Raw material Testing
5.2.1.1, T2(Compound ash content - Any Method)	-	15000	15000 Extra for Raw material Testing
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	15000	15000 Extra for Raw material Testing
5.3(Density of Higher olefin - IS 7328:2020)	-	15000	15000 Extra for Raw material Testing
5.3(Olefin Constituents- 14333-2022)	-	15000	15000 Extra for Raw material Testing
5.3(Loading of Carbon Black - IS 2530:1963)	-	15000	15000 Extra for Raw material Testing
5.3(Ash content- Any Method)	-	15000	15000 Extra for Raw material Testing
5.3(Toluene extract - Any Method)	-	15000	15000 Extra for Raw material Testing
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	15000	15000 Extra for Raw material Testing
5.3(Carbon black particle size - Any Method)	-	15000	15000 Extra for Raw material Testing
5.4(Antioxidant - Any Method)	-	15000	15000 Extra for Raw material Testing
6(Pipe Description - IS 14333-2022)	-	100	-
6.2(Colour- IS 14333-2022)	-	100	-
7.1(Visual Appearance- IS 14333-2022)	-	100	-
7.2(Length- IS 14333-2022)	-	100	-
7.3(Coiling- IS 14333-2022)	-	100	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	1000	1000 For outside diamater, wall thickness,ovality
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	1000	1000 For outside diamater, wall thickness,ovality
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	1000	1000 For outside diamater, wall thickness,ovality
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	3000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	3000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	3000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	3500	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	2000	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	3000	-
8.3(Carbon black content- IS 2530-1963)	-	1500	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	1500	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	3000	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	3000	-
8.6(Density-IS 7328:2020)	-	1500	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1500	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	3000	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	3000	repeat
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	1500	-
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	0	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	0	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	0	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	0	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	0	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	0	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	0	-
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	0	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	0	-
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	0	-
5.2.1.1, T2(Compound ash content - Any Method)	-	0	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	0	-
5.3(Density of Higher olefin - IS 7328:2020)	-	0	-
5.3(Olefin Constituents- 14333-2022)	-	0	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3(Ash content- Any Method)	-	0	-
5.3(Toluene extract - Any Method)	-	0	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	-
5.3(Carbon black particle size - Any Method)	-	0	-
5.4(Antioxidant - Any Method)	-	0	-
6(Pipe Description - IS 14333-2022)	-	0	-
6.2(Colour- IS 14333-2022)	-	0	-
7.1(Visual Appearance- IS 14333-2022)	-	0	-
7.2(Length- IS 14333-2022)	-	0	-
7.3(Coiling- IS 14333-2022)	-	0	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	0	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	0	-
8.3(Carbon black content- IS 2530-1963)	-	0	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	0	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	0	-
8.6(Density-IS 7328:2020)	-	0	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	0	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	0	-

-
Included w.e.f 17.03.2026

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

ALL

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	2000	EXTRA FOR RAW MATERIAL RS 2000
Cl-4.2(Carbon content of finished PE lateral pipe)	-	1000	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	500	-
Cl-6.0(Visual Appearance)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	1500	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	4000	-
Cl-7.2(Reversion Test)	-	1500	-
Cl-7.3(Tensile Test)	-	0	-
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1500	-
Cl-8.0(Supply of pipes)	-	500	-
Cl-9.0(Coiling)	-	500	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	500	-
3(Class of Pipe)	-	500	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	500	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	0	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	1000	-
Cl-4.1(Material)	-	0	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	0	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	0	-
Cl-6.0(Visual Appearance)	-	0	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	0	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	0	-
Cl-7.2(Reversion Test)	-	0	-
Cl-7.3(Tensile Test)	-	0	-
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	0	-
Cl-8.0(Supply of pipes)	-	0	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	0	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	0	-
Cl-4.1(Material)	-	0	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	0	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	0	-
Cl-6.0(Visual Appearance)	-	0	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	0	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	0	-
Cl-7.2(Reversion Test)	-	0	-
Cl-7.3(Tensile Test)	-	0	-
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	0	-
Cl-8.0(Supply of pipes)	-	0	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	0	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	0	-
Cl-4.1(Material)	-	0	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	0	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	0	-
Cl-6.0(Visual Appearance)	-	0	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	0	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	0	-
Cl-7.2(Reversion Test)	-	0	-
Cl-7.3(Tensile Test)	-	0	-
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	0	-
Cl-8.0(Supply of pipes)	-	0	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	0	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	0	-

-
Included w.e.f 17.03.2026

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

ALL

11800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	0	COMPLETE TESTING CHARGE RS 11800/- , EXTRA FOR RAW MATERIAL
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	0	COMPLETE TESTING CHARGE RS 11800/- , EXTRA FOR RAW MATERIAL
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	0	COMPLETE TESTING CHARGE RS 11800/- , EXTRA FOR RAW MATERIAL
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	1000	COMPLETE TESTING CHARGE RS 11800/- , EXTRA FOR RAW MATERIAL
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	1000	COMPLETE TESTING CHARGE RS 11800/- , EXTRA FOR RAW MATERIAL
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	1000	COMPLETE TESTING CHARGE RS 11800/- , EXTRA FOR RAW MATERIAL
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	700	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	300	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	-
6.2.2(Fittings)	-	300	-
6.3(General)	-	300	-
6.3(General)	-	0	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	700	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	700	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	250	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	250	-
8.3.3(Flow Paths in Emitting Unit)	-	400	-
8.3.4(Spacing ofEmitter Units)	-	400	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1600	-
8.5(Resistance to Tension at Elevated Temperature)	-	1100	CL.8.5 RESISTANCE TO TENSION AT ELEVATED TEMPERATURE 50 °Celsius
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	400	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1000	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1000	-
8.8(Determination of Emitting Unit Exponent)	-	400	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	-
4.1 a(Identification)	-	0	-
4.1 a(Identification)	-	0	-
4.1 c(Volatile matter Extract)	-	0	-
4.1 d(Density)	-	0	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	0	-
4.2(Carbon black content)	-	0	-
4.2(Carbon black dispersion)	-	0	-
5.1(Materials)	-	0	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	0	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	0	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	0	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	0	-
6.2(Fittings)	-	0	-
6.3(General)	-	0	-
7.1(Test Specimens)	-	0	-
7.2(Order of Tests)	-	0	-
7.3(Testing Conditions)	-	0	-
7.4(Accuracy of Measuring Devices)	-	0	-
8.1.2(Unregulated Emitting Pipes)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.3(Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregulated Emitting Pipes)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing of Emitter Units)	-	0	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	0	-
8.7.1(Acceptance Test)	-	0	-
8.7.2(Type Test)	-	0	-
8.8(Determination of Emitting Unit Exponen)	-	0	-
9.1(Non-regulated Emitting Pipe)	-	0	-
9.2(Regulated Emitting Pipe)	-	0	-
10.1(Marking)	-	0	-
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	0	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	0	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	0	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	0	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	0	-
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	0	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	0	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	0	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	-
6.2.2(Fittings)	-	0	-
6.3(General)	-	0	-
6.3(General)	-	0	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	0	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing ofEmitter Units)	-	0	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	0	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	0	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	0	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	0	-
8.8(Determination of Emitting Unit Exponent)	-	0	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	-
4.1 a(Identification)	-	0	-
4.1 a(Identification)	-	0	-
4.1 c(Volatile matter Extract)	-	0	-
4.1 d(Density)	-	0	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	0	-
4.2(Carbon black content)	-	0	-
4.2(Carbon black dispersion)	-	0	-
5.1(Materials)	-	0	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	250	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	0	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	0	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	0	-
6.2(Fittings)	-	0	-
6.3(General)	-	0	-
7.1(Test Specimens)	-	0	-
7.2(Order of Tests)	-	0	-
7.3(Testing Conditions)	-	0	-
7.4(Accuracy of Measuring Devices)	-	0	-
8.1.2(Unregulated Emitting Pipes)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.3(Regulated Emitting Pipes)	-	0	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregulated Emitting Pipes)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing of Emitter Units)	-	0	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	0	-
8.7.1(Acceptance Test)	-	0	-
8.7.2(Type Test)	-	0	-
8.8(Determination of Emitting Unit Exponen)	-	0	-
9.1(Non-regulated Emitting Pipe)	-	0	-
9.2(Regulated Emitting Pipe)	-	0	-
10.1(Marking)	-	0	-

-
Included w.e.f 17.03.2026 Exclusion: 5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989) (Potyethylene - anti-oxidant)

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

8000 View breakup
-

Clause No.	Exclusion	Remark
2.1(General)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2(diameter of the socket of cap)	-	COMPLETE TESTING CHARGE RS 8000/-
2.1(General)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2(diameter of the socket of cap)	-	COMPLETE TESTING CHARGE RS 8000/-
6.1.1(VCM Content Test)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2 table 1(Laying length)	-	COMPLETE TESTING CHARGE RS 8000/-

-
Included w.e.f 24.03.2026

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

8000 View breakup
-

Clause No.	Exclusion	Remark
table 1 sl.no: 01(16 )	-	COMPLETE TESTING CHARGE 8000/-
table 1 sl.no: 02(20 )	-	COMPLETE TESTING CHARGE 8000/-
table 1 sl.no: 03(25 )	-	COMPLETE TESTING CHARGE 8000/-
table 1 sl.no: 04(32 )	-	COMPLETE TESTING CHARGE 8000/-
table 1 sl.no: 05(40 )	-	COMPLETE TESTING CHARGE 8000/-
table 1 sl.no: 06(50 )	-	COMPLETE TESTING CHARGE 8000/-
table 1 sl.no: 07(63 )	-	COMPLETE TESTING CHARGE 8000/-
2.1(General)	-	COMPLETE TESTING CHARGE 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE 8000/-
2.2.2, Table 1(Size)	-	COMPLETE TESTING CHARGE 8000/-
2.2.2, Table 1(Union Laying Length)	-	COMPLETE TESTING CHARGE 8000/-
2.2.3( inside diameter of the socket)	-	COMPLETE TESTING CHARGE 8000/-
2.2.3(Socket length)	-	COMPLETE TESTING CHARGE 8000/-
2.1(General)	-	COMPLETE TESTING CHARGE 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE 8000/-
2.2.2, Table 1(Size)	-	COMPLETE TESTING CHARGE 8000/-
2.2.2, Table 1(Union Laying Length)	-	COMPLETE TESTING CHARGE 8000/-
2.2.3( inside diameter of the socket)	-	COMPLETE TESTING CHARGE 8000/-
2.2.3(Socket length)	-	COMPLETE TESTING CHARGE 8000/-
6.1.1(VCM Content Test)	-	COMPLETE TESTING CHARGE 8000/-
2.2.2 table 1(Laying length)	-	COMPLETE TESTING CHARGE 8000/-
6.1.1(VCM Content Test)	-	COMPLETE TESTING CHARGE 8000/-
2.2.2 table 1(Laying length)	-	COMPLETE TESTING CHARGE 8000/-

-
Included w.e.f 24.03.2026

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

8000 View breakup
-

Clause No.	Exclusion	Remark
table 1 sl.no: 01(16 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 02(20 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 03(25 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 04(32 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 05(40 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 06(50 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 07(63 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 08(75 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 09(90 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 10(110 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 11(125 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 12(140 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 13(160 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 14( 180 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 15(200 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 16(225 )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 17(250.0)	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 18(280.0)	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 19(315.0)	-	COMPLETE TESTING CHARGE RS 8000/-
2.1(General)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(Size)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(Socket Laying Length)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3( inside diameter of the socket)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3(Socket length)	-	COMPLETE TESTING CHARGE RS 8000/-
2.1(General)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(Size)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(Socket Laying Length)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3( inside diameter of the socket)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3(Socket length)	-	COMPLETE TESTING CHARGE RS 8000/-
6.1.1(VCM Content Test)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2 table 1(Laying length)	-	COMPLETE TESTING CHARGE RS 8000/-

-
Included w.e.f 24.03.2026

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

8000 View breakup
-

Clause No.	Exclusion	Remark
table 1 sl.no: 01(16 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 02(20 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 03(25 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 04(32 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 05(40 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 06(50 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 07(63 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 08(75 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 09(90 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 10(110 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 11(125 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 12(140 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 13(160 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 14( 180 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 15(200 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 16(225 )	-	Complete testing charge Rs 8000/-
table 1 sl.no: 17(250.0)	-	Complete testing charge Rs 8000/-
table 1 sl.no: 18(280.0)	-	Complete testing charge Rs 8000/-
table 1 sl.no: 19(315.0)	-	Complete testing charge Rs 8000/-
2.1(General)	-	Complete testing charge Rs 8000/-
2.2(Manufacture)	-	Complete testing charge Rs 8000/-
2.2.2, Table 1(Size)	-	Complete testing charge Rs 8000/-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	Complete testing charge Rs 8000/-
2.2.3( inside diameter of the socket)	-	Complete testing charge Rs 8000/-
2.2.3(Socket length)	-	Complete testing charge Rs 8000/-
2.1(General)	-	Complete testing charge Rs 8000/-
2.2(Manufacture)	-	Complete testing charge Rs 8000/-
2.2.2, Table 1(Size)	-	Complete testing charge Rs 8000/-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	Complete testing charge Rs 8000/-
2.2.3( inside diameter of the socket)	-	Complete testing charge Rs 8000/-
2.2.3(Socket length)	-	Complete testing charge Rs 8000/-
6.1.1(VCM Content Test)	-	Complete testing charge Rs 8000/-
2.2.2 table 1(Laying length)	-	Complete testing charge Rs 8000/-
6.1.1(VCM Content Test)	-	Complete testing charge Rs 8000/-
2.2.2 table 1(Laying length)	-	Complete testing charge Rs 8000/-

-
Included w.e.f 17.03.2026

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

8000 View breakup
-

Clause No.	Exclusion	Remark
table 1 sl.no: 01(16 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 02(20 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 03(25 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 04(32 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 05(40 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 06(50 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 07(63 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 08(75 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 09(90 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 10(110 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 11(125 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 12(140 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 13(160(z))	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 01(16 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 02(20 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 03(25 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 04(32 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 05(40 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 06(50 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 07(63 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 08(75 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 09(90 (Z) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 10(110 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 11(125 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 12(140 (Z1) )	-	COMPLETE TESTING CHARGE RS 8000/-
table 1 sl.no: 13(160(z1))	-	COMPLETE TESTING CHARGE RS 8000/-
2.1(General)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(Size)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3( inside diameter of the socket)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3(Socket length)	-	COMPLETE TESTING CHARGE RS 8000/-
2.1(General)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2(Manufacture)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(Size)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3( inside diameter of the socket)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.3(Socket length)	-	COMPLETE TESTING CHARGE RS 8000/-
6.1.1(VCM Content Test)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2 table 1(Laying length)	-	COMPLETE TESTING CHARGE RS 8000/-
6.1.1(VCM Content Test)	-	COMPLETE TESTING CHARGE RS 8000/-
2.2.2 table 1(Laying length)	-	COMPLETE TESTING CHARGE RS 8000/-

-
Included w.e.f 17.03.2026

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

8000 View breakup
-

Clause No.	Exclusion	Remark
cl 2.2.2(Dimensions)	-	Complete Testing Charges Rs 8000/--
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	Complete Testing Charges Rs 8000/-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	Complete Testing Charges Rs 8000/-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	Complete Testing Charges Rs 8000/-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	Complete Testing Charges Rs 8000/-
6.1.1(VCM Content Test)	-	Complete Testing Charges Rs 8000/-
2.2.2 table 1(Laying length)	-	Complete Testing Charges Rs 8000/-
cl 2.2.2(Dimensions)	-	Complete Testing Charges Rs 8000/--
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	Complete Testing Charges Rs 8000/-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	Complete Testing Charges Rs 8000/-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	Complete Testing Charges Rs 8000/-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	Complete Testing Charges Rs 8000/-
6.1.1(VCM Content Test)	-	Complete Testing Charges Rs 8000/-
2.2.2 table 1(Laying length)	-	Complete Testing Charges Rs 8000/-
cl 2.2.2(Dimensions)	-	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	-
6.1.1(VCM Content Test)	-	-
2.2.2 table 1(Laying length)	-	-

-
Included w.e.f 17.02.2026

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

8000 View breakup
-

Clause No.	Exclusion	Remark
table 1 sl.no: 01(16 )	-	complete testing charge 8000
table 1 sl.no: 02(20 )	-	complete testing charge 8000
table 1 sl.no: 03(25 )	-	complete testing charge 8000
table 1 sl.no: 04(32 )	-	complete testing charge 8000
table 1 sl.no: 05(40 )	-	complete testing charge 8000
table 1 sl.no: 06(50 )	-	complete testing charge 8000
table 1 sl.no: 07(63 )	-	complete testing charge 8000
table 1 sl.no: 08(75 )	-	complete testing charge 8000
table 1 sl.no: 09(90 )	-	complete testing charge 8000
table 1 sl.no: 10(110 )	-	complete testing charge 8000
table 1 sl.no: 11(125 )	-	complete testing charge 8000
table 1 sl.no: 12(140 )	-	complete testing charge 8000
table 1 sl.no: 13(160 )	-	complete testing charge 8000
table 1 sl.no: 14( 180 )	-	complete testing charge 8000
table 1 sl.no: 15(200 )	-	complete testing charge 8000
table 1 sl.no: 16(225 )	-	complete testing charge 8000
table 1 sl.no: 17(250.0)	-	complete testing charge 8000
table 1 sl.no: 18(280.0)	-	complete testing charge 8000
table 1 sl.no: 19(315.0)	-	complete testing charge 8000
2.1(General)	-	complete testing charge 8000
2.2(Manufacture)	-	complete testing charge 8000
2.2.2, Table 1(Size)	-	complete testing charge 8000
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	complete testing charge 8000
2.2.3( inside diameter of the socket)	-	complete testing charge 8000
2.2.3(socket length)	-	complete testing charge 8000
2.1(General)	-	complete testing charge 8000
2.2(Manufacture)	-	complete testing charge 8000
2.2.2, Table 1(Size)	-	complete testing charge 8000
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	complete testing charge 8000
2.2.3( inside diameter of the socket)	-	complete testing charge 8000
2.2.3(socket length)	-	complete testing charge 8000
6.4 PART-1(Short term hydraulic test)	-	complete testing charge 8000
6.1.1(VCM Content Test)	-	complete testing charge 8000
2.2.2 table 1(Laying Length)	-	complete testing charge 8000
6.4 PART-1(Short term hydraulic test)	-	complete testing charge 8000
6.1.1(VCM Content Test)	-	complete testing charge 8000
2.2.2 table 1(Laying Length)	-	complete testing charge 8000
6.4 PART-1(Short term hydraulic test)	-	complete testing charge 8000
6.1.1(VCM Content Test)	-	complete testing charge 8000
2.2.2 table 1(Laying Length)	-	complete testing charge 8000
6.4 PART-1(Short term hydraulic test)	-	complete testing charge 8000
6.1.1(VCM Content Test)	-	complete testing charge 8000
2.2.2 table 1(Laying Length)	-	complete testing charge 8000
6.4 PART-1(Short term hydraulic test)	-	complete testing charge 8000
6.1.1(VCM Content Test)	-	complete testing charge 8000
2.2.2 table 1(Laying Length)	-	complete testing charge 8000
6.4 PART-1(Short term hydraulic test)	-	complete testing charge 8000
6.1.1(VCM Content Test)	-	complete testing charge 8000
2.2.2 table 1(Laying Length)	-	complete testing charge 8000

-
Included w.e.f 17.02.2026

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	1000	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	1000	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	1000	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	1000	-
Cl. 6.1(Stress Relief Test- Appendix A)	-	5000	-
Cl. 6.2(Opacity- Appendix B)	-	1000	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	1500	-
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	1500	-
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	1500	-
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	1500	-
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	5000	-
6.1.1(VCM Content Test)	-	5000	-
3(Size of Fitting -)	-	0	-
4(Minimum thickness)	-	0	-
5(Socket dimensions)	-	0	-
6.1(Stress Relief Test)	-	0	-
6.2(Opacity)	-	0	-
6.3(Effect on Water)	-	0	-
6.4(Short-Term Hydraulic Test)	-	0	-
7.2(Production Routine Tests)	-	0	-
Cl 6.3(Effect on Water Lead (first extraction))	-	0	-
Cl 6.3(Effect on Water Lead (third extraction))	-	0	-
Cl 6.3(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	0	-
Cl 6.3(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 6.3(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
CL 4.0(Wall thickness (average of 4.0))	-	0	-
CL 5.1(Sockt Length ( Take 4 reading and minimum will be reported))	-	0	-
Cl.4(Minimum Thickness)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	-
Cl. 6.1(Stress Relief Test- Appendix A)	-	0	-
Cl. 6.2(Opacity- Appendix B)	-	0	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	-
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	0	-
6.1.1(VCM Content Test)	-	0	-
3(Size of Fitting -)	-	0	-
4(Minimum thickness)	-	0	-
5(Socket dimensions)	-	0	-
6.1(Stress Relief Test)	-	0	-
6.2(Opacity)	-	0	-
6.3(Effect on Water)	-	0	-
6.4(Short-Term Hydraulic Test)	-	0	-
7.2(Production Routine Tests)	-	0	-
Cl 6.3(Effect on Water Lead (first extraction))	-	0	-
Cl 6.3(Effect on Water Lead (third extraction))	-	0	-
Cl 6.3(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	0	-
Cl 6.3(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 6.3(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
CL 4.0(Wall thickness (average of 4.0))	-	0	-
CL 5.1(Sockt Length ( Take 4 reading and minimum will be reported))	-	0	-
Cl.4(Minimum Thickness)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	-
Cl. 6.1(Stress Relief Test- Appendix A)	-	0	-
Cl. 6.2(Opacity- Appendix B)	-	0	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	-
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	0	-
6.1.1(VCM Content Test)	-	0	-
3(Size of Fitting -)	-	0	-
4(Minimum thickness)	-	0	-
5(Socket dimensions)	-	0	-
6.1(Stress Relief Test)	-	0	-
6.2(Opacity)	-	0	-
6.3(Effect on Water)	-	0	-
6.4(Short-Term Hydraulic Test)	-	0	-
7.2(Production Routine Tests)	-	0	-
Cl 6.3(Effect on Water Lead (first extraction))	-	0	-
Cl 6.3(Effect on Water Lead (third extraction))	-	0	-
Cl 6.3(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	0	-
Cl 6.3(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 6.3(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
CL 4.0(Wall thickness (average of 4.0))	-	0	-
CL 5.1(Sockt Length ( Take 4 reading and minimum will be reported))	-	0	-

-
Included w.e.f 17.02.2026

IS 17546 (2021)

Chlorinated polyvinyl chloride CPVC fittings for potable hot and cold water distribution supplies Specification

84000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Nominal Size(DN))	-	500	-
3.2(Nominal Outside Diameter)	-	500	-
3.3(Mean Inside Diameter of Socket at Entry)	-	500	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	-
3.5(Out-of-Roundness (Ovality))	-	500	-
3.6(Nominal Wall Thickness)	-	500	-
3.7(Minimum Wall Thickness)	-	500	-
3.8(Tolerance)	-	0	-
3.9(Working Pressure)	-	0	-
3.1(Standard Dimension Ratio)	-	0	-
3.11(Type Tests)	-	0	-
3.11(Acceptance Tests)	-	0	-
6(Composition)	-	12000	-
7(Dimensions of fitting)	-	3500	-
8.2(Opacity)	-	2000	-
8.1(Visual Appearance)	-	500	-
8.3(Stress Relief Test)	-	3000	-
8.4(Vicat softening Temperature)	-	4000	-
8.5(Density)	-	3000	-
8.6(Effect on water)	-	7000	-
9(Mechanical Properties)	-	20000	ACCEPTANCE 1hr - 3000rs , 165 hrs -5000rs , 1000hr - 12000hrs , Thermal stability-29000
11(Marking)	-	0	-
Cl-6.2.2(Compound Chlorine Content)	-	0	0
Cl-6.2.5(Verification of the Malfunction Temperature)	-	0	0
Cl-9.1(Hydrostatic Characteristics)	-	0	0
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	29000	Thermal stability-29000

-
Included w.e.f. 27.01.2026

IS 14587 (2025)

Prelaminated Medium Density Fibre Boards of Wood and Other Lignocellulosic Materials - Specification ( Second Revision )

21500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	500	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	1000	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	1000	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	1000	-
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	1500	-
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	500	-
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	500	-
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	500	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	500	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	500	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	2500	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	0	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	0	-
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	0	-
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	0	-
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	0	-
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	0	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	0	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	0	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	0	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-

-
included w.e.f 14.01.2026

IS 12823 (2025)

Prelaminated Medium Density Particle Boards from Wood and other Lignocellulosic Material Specification (Second Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 5(Material - IS 3087)	-	0	-
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	500	-
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	500	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	1500	-
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	1500	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	1500	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	1000	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	1000	-
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	1500	-
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	500	-
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	500	-
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	500	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	500	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	2500	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-
As per Clause 5(Material - IS 3087)	-	0	-
As per Clause 8 Table 2(Length -IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Width - IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Thickness - IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Squareness, Max -IS 2380 (Part 2))	-	0	-
As per Clause 8 Table 2(Edge Straighness, Max - IS 2380 (Part 2))	-	0	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	0	-
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	0	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	0	-
As per Clause 9.1 , Table 8(Abrasion resistance in number of revolutions Min. --Annex. B)	-	0	-
As per Clause 9.1 , Table 8(Resiatnce to stream/water vapour - Annex. C)	-	0	-
As per Clause 9.1 , Table 8(Resitance to crack -Annex. D)	-	0	-
As per Clause 9.1 , Table 8(Resistance to cigarette burn -Annex. E)	-	0	-
As per Clause 9.1 , Table 8(Resiatnce to stain - Annex. F)	-	0	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	0	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-

-
included w.e.f 14.01.2026

IS 3097 (2025)

Veneered Medium Density Particle Boards from Wood and other Lignocellulosic Material - Specification ( Third Revision )

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.1 and Table 1(Classification based on surface characteristics)	-	500	For Classification and grade
Cl. 4.1 and Table 1(Grade)	-	0	-
Cl. 4.2(Formaldehyde Classes)	-	2500	-
Cl. 8.1 and Table 2(i)(Dimensions and Tolerances(Length))	-	500	-
Cl. 8.1 and Table 2(ii)(Dimensions and Tolerances(Width))	-	500	-
Cl. 8.2 and Table 2(iii)(Dimensions and Tolerances(Thickness))	-	500	-
Cl. 8.3 and Table 2(iv)(Squareness)	-	500	-
Cl. 8.3 and Table 2(v)(Edge Straightness)	-	500	-
Cl. 9.1 and Table 3(i)(Density)	-	1000	-
Cl. 9.1 and Table 3(ii)(Variation from mean density)	-	1000	-
Cl. 9.1 and Table 3(iii)(Moisture Content)	-	1500	-
Cl. 9.1 and Table 4(i)/5(i)/6(i)/7(i)(Modulus of Rupture(MoR))	-	1500	-
Cl. 9.1 and Table 4(ii)/6(ii)/7(ii)(Modulus of Elasticity(MoE))	-	1500	-
Cl. 9.1 and Table 4(iii)/5(ii)/6(iii)/7(iii)(Internal bond strength)	-	1500	-
Cl. 9.1 and Table 6(iv)/7(iv)(24 h thickness swelling(due to general water absorption))	-	1500	-
Cl. 9.1 and Table 4(iv)/5(iii)/6(v)/7(v)("Screw withdrawal strength (face)")	-	1500	-
Cl. 9.1 and Table 4(v)/5(iv)/6(vi)/7(vi)("Screw withdrawal strength (edge)")	-	1500	-
Cl. 9.1 and Table 6(vii)(a)/7(vii)(a)(Internal bond strength(after cyclic test))	-	1000	-
Cl. 9.1 and Table 6(vii)(b)/7(vii)(b)(Internal bond strength(boil test))	-	1000	-
Cl. 9.4 and Table 8(i)(Formaldehyde content)	-	2500	-
Cl. 9.4 and Table 8(ii)(Steady-state formaldehyde emmision (optional test))	-	0	-
Cl. 9.3.1(Adhesion of Plies)	-	1000	-

-
included w.e.f 14.01.2026

IS 3087 (2025)

Medium Density Particle Boards of Wood and other Lignocellulosic Materials for General Purpose - Specification ( Third Revision )

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	500	Rs- 19500/-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	500	Rs- 19500/-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	500	Rs- 19500/-
As per Clause 8, Table 2(Thickness, Sanded/finished panel - IS 2380 (Part 2))	-	500	Rs- 19500/-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	500	Rs- 19500/-
As per Clause 8, Table 2(Edge straightness, Max. -IS 2380 (Part 2))	-	500	Rs- 19500/-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	Rs- 19500/-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	Rs- 19500/-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1500	Rs- 19500/-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	1500	Rs- 19500/-
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	1500	Rs- 19500/-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	1500	Rs- 19500/-
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	1500	Rs- 19500/-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	1500	Rs- 19500/-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	1500	Rs- 19500/-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	1000	Rs- 19500/-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	1000	Rs- 19500/-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	2500	Rs- 19500/-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	(optional test)
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	0	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Thickness, Sanded/finished panel - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Edge straightness, Max. -IS 2380 (Part 2))	-	0	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	0	-
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	0	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	0	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	0	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	0	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Thickness, Sanded/finished panel - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Edge straightness, Max. -IS 2380 (Part 2))	-	0	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	0	-
As per Clause 9.1 Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	0	-
As per Clause 9.1 , Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	0	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	0	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-

-
included w.e.f 14.01.2026

IS 12406 (2025)

Medium Density Fibre Boards of Wood and Other Lignocellulosic Materials for General Purpose - Specification ( Third Revision )

GRADE 1& 2 , CLASS E1 & E2

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	0	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	1000	FOR DIMENSION
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	1000	FOR DIMENSION
As per Clause 8, Table 2(Thickness - IS 2380 (Part 2))	-	1000	FOR DIMENSION
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	1000	FOR DIMENSION
As per Clause 8, Table 2(Edge straightness, Max.)	-	1000	FOR DIMENSION
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	1000	For Density Test
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	1000	For Density Test
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	1000	For Moisture Content Test
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	1000	For Modulus of rupture test
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	1000	For Modulus of elasticity test
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	1000	For Internal Bond Strength Test
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	3000	For Linear expansion Test
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	3000	For screw withdrawal strength test
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	3000	For Internal Bond Strength Test
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	3000	For Internal Bond Strength Test
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	3000	For formaldehyde content test
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-
Cl-5.1(Wood and Any Other Lignocellulosic Material)	-	0	-
Cl-5.2(Adhesive)	-	6867	EXTRA FOR ADHESIVE TESTING
Cl-5.3(Sizing Material)	-	0	-
Cl-5.4(Preservative Treatment)	-	3000	FOR PRESERVATIVE TREATMENT
Cl-6(MANUFACTURE)	-	0	-
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	0	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Thickness - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Edge straightness, Max.)	-	0	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	0	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	0	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-
Cl-5.1(Wood and Any Other Lignocellulosic Material)	-	0	-
Cl-5.2(Adhesive)	-	0	-
Cl-5.3(Sizing Material)	-	0	-
Cl-5.4(Preservative Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	0	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Thickness - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Edge straightness, Max.)	-	0	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	0	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	0	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-
Cl-5.1(Wood and Any Other Lignocellulosic Material)	-	0	-
Cl-5.2(Adhesive)	-	0	-
Cl-5.3(Sizing Material)	-	0	-
Cl-5.4(Preservative Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
As per Clause 7(Finish --IS 2380 (Part 2), IS 2380 (Part 3) & Visual)	-	0	-
As per Clause 8, Table 2(Length -IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Width - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Thickness - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Squareness, Max. - IS 2380 (Part 2))	-	0	-
As per Clause 8, Table 2(Edge straightness, Max.)	-	0	-
As per Clause 9.1 Table 3(Density -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Variation from mean density, --IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 3(Moisture Content -IS 2380 (Part 3))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of rupture (MoR), Min.-IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Modulus of elasticity (MoE), Min. -(IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table7(Internal bond strength, Min. - IS 2380 (Part 5))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(24 h thickness swelling (due to general absorption) Max. - IS 2380 (Part 17))	-	0	-
As per Clause 9.1 Table 4, Table 5, Table 6, Table 7(Screw withdrawal strength (face) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 Table 4, Table 5, table 6, Table 7(Screw withdrawal strength (edge) , Min. -IS 2380 (Part 4))	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 1 : Cyclic test (1. )Internal bond strength Min. -IS 2380 (Part 5) see note 1)	-	0	-
As per Clause 9.1 , Table 5, Table 6, Table 7(Moisture Resistance : Option 2 : Boil test (1.) Internal bond strength , Min.- IS 2380 (Part 5) see note 2)	-	0	-
As per Clause 9.1 , Table 9(Formaldehyde content Fc, mg/100 g for oven dry board -IS 13745)	-	0	-
As per Clause 9.1 , Table 9(Steady-state formaldehyde emission, Fc, mg/m3 (optional test))	-	0	-
Cl-5.1(Wood and Any Other Lignocellulosic Material)	-	0	-
Cl-5.2(Adhesive)	-	0	-
Cl-5.3(Sizing Material)	-	0	-
Cl-5.4(Preservative Treatment)	-	0	-
Cl-6(MANUFACTURE)	-	0	-

-
Included w.e.f 31.12.2025

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
19(Marking)	-	0	-
3(Type of Fitting)	-	0	-
4(Size Designation)	-	0	-
5(Colour of fittings)	-	500	-
7.1,Table 1(Wall thickness)	-	1500	-
7.2 ,Table 2&3(Socket Dimensions)	-	500	-
7.3(Dimensions of waste trap(Nahani Trap)	-	0	-
8(Sealing Rings)	-	500	-
10(Workmanship)	-	500	-
11(Design requirements)	-	0	-
11.1(Solvent cement type or Rubber ring type)	-	0	-
11.2(Socket and spigot configeration)	-	0	-
11.4,Table 5(Vent cowl)	-	500	-
11.5,Table 6(Pipe Clips)	-	500	-
12(Physical test requirements)	-	0	-
12.1(Visual appearance)	-	500	-
12.2(Stress relief test)	-	1500	-
12.3(Vicat softening tempewrature)	-	2000	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	4000	-
Cl.14, Annex A(Titanium Di-Oxide Content)	-	2000	-
Cl.15, Annex B(Sulphated Ash Content)	-	1500	-
16(Mechanical Properties)	-	0	-
16.1(Impact test)	-	1500	-
17(Watet tightness of joint)	-	1500	-
12.4(Effect on water test)	-	5000	-
7.4(Chamfer)	-	0	-
11.3(Access Openings)	-	500	-
Table 4(Dimension of Access Openings)	-	0	-
Cl 12.4(Effect on Water Lead (first extraction))	-	0	-
Cl 12.4(Effect on Water Lead (third extraction))	-	0	-
Cl 12.4(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	0	-
Cl 12.4(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 12.4(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
19(Marking)	-	0	-
3(Type of Fitting)	-	0	-
4(Size Designation)	-	0	-
5(Colour of fittings)	-	0	-
7.1,Table 1(Wall thickness)	-	0	-
7.2 ,Table 2&3(Socket Dimensions)	-	0	-
7.3(Dimensions of waste trap(Nahani Trap)	-	0	-
8(Sealing Rings)	-	0	-
10(Workmanship)	-	0	-
11(Design requirements)	-	0	-
11.1(Solvent cement type or Rubber ring type)	-	0	-
11.2(Socket and spigot configeration)	-	0	-
11.4,Table 5(Vent cowl)	-	0	-
11.5,Table 6(Pipe Clips)	-	0	-
12(Physical test requirements)	-	0	-
12.1(Visual appearance)	-	0	-
12.2(Stress relief test)	-	0	-
12.3(Vicat softening tempewrature)	-	0	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	0	-
Cl.14, Annex A(Titanium Di-Oxide Content)	-	0	-
Cl.15, Annex B(Sulphated Ash Content)	-	0	-
16(Mechanical Properties)	-	0	-
16.1(Impact test)	-	0	-
17(Watet tightness of joint)	-	0	-
12.4(Effect on water test)	-	0	-
7.4(Chamfer)	-	0	-
11.3(Access Openings)	-	0	-
Table 4(Dimension of Access Openings)	-	0	-
Cl 12.4(Effect on Water Lead (first extraction))	-	0	-
Cl 12.4(Effect on Water Lead (third extraction))	-	0	-
Cl 12.4(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	0	-
Cl 12.4(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 12.4(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
19(Marking)	-	0	-
3(Type of Fitting)	-	0	-
4(Size Designation)	-	0	-
5(Colour of fittings)	-	0	-
7.1,Table 1(Wall thickness)	-	0	-
7.2 ,Table 2&3(Socket Dimensions)	-	0	-
7.3(Dimensions of waste trap(Nahani Trap)	-	0	-
8(Sealing Rings)	-	0	-
10(Workmanship)	-	0	-
11(Design requirements)	-	0	-
11.1(Solvent cement type or Rubber ring type)	-	0	-
11.2(Socket and spigot configeration)	-	0	-
11.4,Table 5(Vent cowl)	-	0	-
11.5,Table 6(Pipe Clips)	-	0	-
12(Physical test requirements)	-	0	-
12.1(Visual appearance)	-	0	-
12.2(Stress relief test)	-	0	-
12.3(Vicat softening tempewrature)	-	0	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	0	-
Cl.14, Annex A(Titanium Di-Oxide Content)	-	0	-
Cl.15, Annex B(Sulphated Ash Content)	-	0	-
16(Mechanical Properties)	-	0	-
16.1(Impact test)	-	0	-
17(Watet tightness of joint)	-	0	-
12.4(Effect on water test)	-	0	-
7.4(Chamfer)	-	0	-
11.3(Access Openings)	-	0	-
Table 4(Dimension of Access Openings)	-	0	-
Cl 12.4(Effect on Water Lead (first extraction))	-	0	-
Cl 12.4(Effect on Water Lead (third extraction))	-	0	-
Cl 12.4(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	0	-
Cl 12.4(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 12.4(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-

-
Included w.e.f. 24.12.2025

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	2000	-
9.5(Tensile Strength IS 12235(Part 13))	-	2500	-
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	2000	-
9.3(Density IS 12235 (Part 14))	-	750	-
9.2(Internal Diameter)	-	500	-
9.1( Visual Appearance)	-	250	-
9.1(Visual Appearance)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	-
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	-
8.4(Sealing rings - Hardness)	-	500	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	500	-
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	0	-
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	250	-
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	250	-
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	250	-
7.4 Table 8 & 9 Fig 1(Segmental length for Spigot (average of 4.0))	-	500	-
7.4 Table 8 & 9 Fig 1(Segmental length,mm for socket (average of 4.0))	-	500	-
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	500	-
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	500	-
7.3.2(Rib height)	-	250	-
7.3.1(No.of Ribs)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	250	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-	250	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	250	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	250	-
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	500	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	250	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	250	-
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	0	-
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	0	-
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	5000	-
5(COLOUR)	-	250	-
8.4(Sealing elements a. Elastomeric material b. Shore A hardness of sealing Elements )	-	0	-
8.4(Width b)	-	0	-
8.3.1 & 8.3.2 (Threading of casing pipe (from 100 to 200 DN Table – 11 & Fig. 3A) & (from 250 to 400 DN Table – 12 & Fig. 4A) Outside diameter d1(+0, -0.3) d2 d3 D1 (+0.3, -0) D2 D4 D5 (+0.3, -0) Z h3 (+0, -0.1) H4 (+0, -0.1) )	-	500	-
8.2(Threading of casing pipe As per IS 554 (from 40 to 80mm DN) Number of threads in 25.4mm Pitch (P) Height of thread (h) Major (Gauge Diameter) d Pitch(d2) Minor (d1) External Thread gauge length Nominal No. of turns of thread max min )	-	500	-
7.5.1 7.5.2 (Slot Dimension (Table 10) Fig 2A & 2B a. Minimum number of slot on the circumference b. Σa±5% c. Mean value of approximate free passage area (%) for width of slot (w) d. Tolerance on width of slot (w) e. Width of material between slot (b))	-	0	-
5.0(Colour of Pipes)	-	0	-
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	5000	-
4.1.2(K-Value as per IS-4669)	-	2000	Extra charge For Raw-material Testing
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	0	Extra charge For Raw-material Testing
7.1(Screen Pipes)	-	500	-
11(Marking)	-	2000	-
5.1(Materials)	-	0	-
8(Packing)	-	0	-
4.1.3(Cross Chain Length)	-	0	-
7.2(Link Twisted (Cross chain))	-	0	-
7.3(The Basic chains)	-	0	-
7.9(Case Depth)	-	0	-
8(Marking)	-	0	-
Cl 9.7(Effect on Water Lead (first extraction))	-	0	-
Cl 9.7(Effect on Water Lead (third extraction))	-	0	-
Cl 9.7(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	0	-
Cl 9.7(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 9.7(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
CL 7.1,7.2(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	250	-

-
Included w.e.f. 24.12.2025

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4( Designation)	-	0	-
Cl 7(Dimensions Of Pipes)	-	3000	-
Cl 8(Visual Appearance)	-	500	-
Cl 9.1(Hydraulic Characteristics)	-	15000	-
Cl 9.2(Fusion Compatibility)	-	2000	-
Cl 9.3(Reversion Test )	-	5000	-
Cl 9.4 & Annex B(Impact Strength)	-	5000	-
Cl 9.5(Density)	-	1000	-
Cl 9.6(Melt Flow Rate)	-	2000	-
Cl 9.7(Carbon Black Content & Dispersion)	-	2000	-
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	125000	-
Cl 9.9(Opacity)	-	2000	-
5(Colour)	-	0	-
Cl 4( Designation)	-	0	-
Cl 7(Dimensions Of Pipes)	-	0	-
Cl 8(Visual Appearance)	-	0	-
Cl 9.1(Hydraulic Characteristics)	-	0	-
Cl 9.2(Fusion Compatibility)	-	0	-
Cl 9.3(Reversion Test )	-	0	-
Cl 9.4 & Annex B(Impact Strength)	-	0	-
Cl 9.5(Density)	-	0	-
Cl 9.6(Melt Flow Rate)	-	0	-
Cl 9.7(Carbon Black Content & Dispersion)	-	0	-
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	0	-
Cl 9.9(Opacity)	-	0	-
5(Colour)	-	0	-

-
Included w.e.f. 24.12.2025

IS 2202 : Part 2 (2022)

WOODEN FLUSH DOOR SHUTTERS SOLID CORE TYPE SPECIFICATION PART 2 PARTICLE BOARD HIGH DENSITY FIBRE BOARD MEDIUM DENSITY FIBRE BOARD AND HARDBOARD FACE PANELS Fourth Revision

BWP,MR

24500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 6.1(Timber)	-	0	-
Clause No -6.2(Alternative Materials (LVL)	-	0	-
Clause No -6.2(Alternative Materials veneer laminated lumber (VLL))	-	0	-
Clause No -6.2(Alternative Materials medium density fibre board (MDF))	-	0	-
Clause No -6.2(Alternative Materials -plywood)	-	0	-
Clause No -6.2(BWP grade flush door shutter)	-	0	-
Clause No -6.3.1("Face Panels: Particle Board MDF/ HDF Fibre Hardboard")	-	0	-
Clause No -6.4(Adhesive)	-	8000	Extra for IS 848
Clause No -7.1(Construction)	-	500	-
Clause No - 7.3(" MDF board or HDF board ")	-	500	-
Clause No -9.2("Workmanship and finish")	-	500	-
Clause No -10.1(tests for flush door shutters)	-	19500	-
Clause No -10.2(End Immersion Test)	-	2000	-
Clause No -10.3(Glue Adhesion Test)	-	1000	-
Clause No -11(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause No -12("ADDITIONAL REQUIREMENTS FOR ECO MARK")	-	0	-
5(SIZES AND TOLERANCES)	-	500	-
6.5(The swelling in thickness of the particle board, MDF and HDF board for core)	-	1000	-
Cl-6.3.3 (Amendment NO 1)(B D P V, P D P V and M D P V types of flush door)	-	500	-
Cl-6.3.2(MDF board and HDF board)	-	0	-
Cl-6.3.4(B N P V, P N P V and M N P V,)	-	0	-
Cl-7.2(Face Panel)	-	500	-
Cl-7.4 (Amendment No 1)(Door Blanks)	-	400	-
Cl-8(Fittings)	-	0	-
Clause No - 6.1(Timber)	-	0	-
Clause No -6.2(Alternative Materials (LVL)	-	0	-
Clause No -6.2(Alternative Materials veneer laminated lumber (VLL))	-	0	-
Clause No -6.2(Alternative Materials medium density fibre board (MDF))	-	0	-
Clause No -6.2(Alternative Materials -plywood)	-	0	-
Clause No -6.2(BWP grade flush door shutter)	-	0	-
Clause No -6.3.1("Face Panels: Particle Board MDF/ HDF Fibre Hardboard")	-	0	-
Clause No -6.4(Adhesive)	-	0	-
Clause No -7.1(Construction)	-	0	-
Clause No - 7.3(" MDF board or HDF board ")	-	0	-
Clause No -9.2("Workmanship and finish")	-	0	-
Clause No -10.1(tests for flush door shutters)	-	0	-
Clause No -10.2(End Immersion Test)	-	0	-
Clause No -10.3(Glue Adhesion Test)	-	0	-
Clause No -11(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause No -12("ADDITIONAL REQUIREMENTS FOR ECO MARK")	-	0	-
5(SIZES AND TOLERANCES)	-	0	-
6.5(The swelling in thickness of the particle board, MDF and HDF board for core)	-	0	-
Cl-6.3.3 (Amendment NO 1)(B D P V, P D P V and M D P V types of flush door)	-	0	-
Cl-6.3.2(MDF board and HDF board)	-	0	-
Cl-6.3.4(B N P V, P N P V and M N P V,)	-	0	-
Cl-7.2(Face Panel)	-	0	-
Cl-7.4 (Amendment No 1)(Door Blanks)	-	0	-
Cl-8(Fittings)	-	0	-
Clause No - 6.1(Timber)	-	0	-
Clause No -6.2(Alternative Materials (LVL)	-	0	-
Clause No -6.2(Alternative Materials veneer laminated lumber (VLL))	-	0	-
Clause No -6.2(Alternative Materials medium density fibre board (MDF))	-	0	-
Clause No -6.2(Alternative Materials -plywood)	-	0	-
Clause No -6.2(BWP grade flush door shutter)	-	0	-
Clause No -6.3.1("Face Panels: Particle Board MDF/ HDF Fibre Hardboard")	-	0	-
Clause No -6.4(Adhesive)	-	0	-
Clause No -7.1(Construction)	-	0	-
Clause No - 7.3(" MDF board or HDF board ")	-	0	-
Clause No -9.2("Workmanship and finish")	-	0	-
Clause No -10.1(tests for flush door shutters)	-	0	-
Clause No -10.2(End Immersion Test)	-	0	-
Clause No -10.3(Glue Adhesion Test)	-	0	-
Clause No -11(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause No -12("ADDITIONAL REQUIREMENTS FOR ECO MARK")	-	0	-
5(SIZES AND TOLERANCES)	-	0	-
6.5(The swelling in thickness of the particle board, MDF and HDF board for core)	-	0	-
Cl-6.3.3 (Amendment NO 1)(B D P V, P D P V and M D P V types of flush door)	-	0	-
Cl-6.3.2(MDF board and HDF board)	-	0	-
Cl-6.3.4(B N P V, P N P V and M N P V,)	-	0	-
Cl-7.2(Face Panel)	-	0	-
Cl-7.4 (Amendment No 1)(Door Blanks)	-	0	-
Cl-8(Fittings)	-	0	-
Clause No - 6.1(Timber)	-	0	-
Clause No -6.2(Alternative Materials (LVL)	-	0	-
Clause No -6.2(Alternative Materials veneer laminated lumber (VLL))	-	0	-
Clause No -6.2(Alternative Materials medium density fibre board (MDF))	-	0	-
Clause No -6.2(Alternative Materials -plywood)	-	0	-
Clause No -6.2(BWP grade flush door shutter)	-	0	-
Clause No -6.3.1("Face Panels: Particle Board MDF/ HDF Fibre Hardboard")	-	0	-
Clause No -6.4(Adhesive)	-	0	-
Clause No -7.1(Construction)	-	0	-
Clause No - 7.3(" MDF board or HDF board ")	-	0	-
Clause No -9.2("Workmanship and finish")	-	0	-
Clause No -10.1(tests for flush door shutters)	-	0	-
Clause No -10.2(End Immersion Test)	-	0	-
Clause No -10.3(Glue Adhesion Test)	-	0	-
Clause No -11(SAMPLING AND CRITERIA FOR CONFORMITY)	-	0	-
Clause No -12("ADDITIONAL REQUIREMENTS FOR ECO MARK")	-	0	-
5(SIZES AND TOLERANCES)	-	0	-
6.5(The swelling in thickness of the particle board, MDF and HDF board for core)	-	0	-
Cl-6.3.3 (Amendment NO 1)(B D P V, P D P V and M D P V types of flush door)	-	0	-
Cl-6.3.2(MDF board and HDF board)	-	0	-
Cl-6.3.4(B N P V, P N P V and M N P V,)	-	0	-
Cl-7.2(Face Panel)	-	0	-
Cl-7.4 (Amendment No 1)(Door Blanks)	-	0	-
Cl-8(Fittings)	-	0	-

-
included w.e.f 14.01.2026

IS 848 (2025)

Synthetic Resin Adhesives for Plywood (Phenolic, Aminoplastic and Bio-Materials Based) - Specification ( Third Revision )

BWP, BWR, MR

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 4 Table 1(TYPES)	-	0	Complete testing charge for each grade
As per Clause 6.6(SETTING TIMES AND CONDITIONS)	-	0	Complete testing charge for each grade
As per Clause 7.3.2 Table 1(i)(Cyclic Test For BWP Type)	-	7500	Complete testing charge for each grade
As per Clause 7.3.2 Table 1(ii)(Cyclic Test For BWR Type)	-	7500	Complete testing charge for each grade
As per Clause 7.3.2 Table 1(iii)(Cyclic Test For MR Type)	-	7500	Complete testing charge for each grade
As per Clause 7.4(Acidity And Alkalinity (pH))	-	7500	Complete testing charge for each grade
As per Clause 9(Marking)	-	0	Complete testing charge for each grade

-
Included w.e.f 17-12-2025.

Bureau of Indian Standards

The National Standards Body of India

AANKAN CALIBRATION AND TESTING CENTRE LLP, DANTLI

PLOT NO. B, LS NO. 193, DANTALI, Gandhinagar, Gujarat, 382721

9879564686 aankan.act@gmail.com

Scope List