BIS - LIMS (Laboratory Information Management System)

Global Testing Laboratory Private limited, Ghaziabad

Plot No.55,Gali No.5A, Rajendra Nagar Industrial Area, Mohan Nagar Ghaziabad, Uttar Pradesh, Ghaziabad, Uttar Pradesh, 201007

8368402864 info@globaltestinglaboratory.com

Scope List

Reset

17 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 16246 (2015)

Elastomer insulated cables with limited circuit integrity when affected by fire - Specification

65000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1( Cables for Fixed Installation)	-	0	-
Cl.5( INSULATION)	-	0	-
Cl. 6.1( Glass Tape)	-	0	-
Cl 6.2( Polyethylene Teraphthalate (PETP) or Polypropylene base Tape)	-	0	-
Cl 6.4( Fire Barrier Tape)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 7(CENTRE AND FILLERS)	-	0	-
Cl 8( ARMOUR)	-	0	-
Cl 9.1( Inner Sheath)	-	0	-
Cl 9.2( Outer Sheath)	-	0	-
Cl 10.1( CONDUCTORS)	-	0	-
Cl 10.2( CONDUCTORS)	-	0	-
Cl 11.1( INSULATION)	-	0	-
Cl 11.2(Thickness of Insulation IS 10810 : Part 6)	-	0	-
Cl 12( CORE IDENTIFICATION)	-	0	-
Cl 13( LAYING UP OF CORES)	-	0	-
Cl 14.2( Thickness of Inner Sheath IS 10810 : Part 6)	-	0	-
Cl 15.1( ARMOURING)	-	0	-
Cl 15.3.1( Type of Armour)	-	0	-
Cl 15.3.2( Type of Armour)	-	0	-
Cl 15.3.3( ARMOURING)	-	0	-
Cl 15.3.3( ARMOURING)	-	0	-
Cl 15.4.1( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 15.4.2( ARMOURING)	-	0	-
Cl 16.2( OUTER SHEATH)	-	0	-
Cl 16.3( Thickness of Outer Sheath - Avg IS 10810 : Part 6)	-	0	-
Cl 16.3( Thickness of Outer Sheath - Minimum IS 10810 : Part 6)	-	0	-
Cl 17.2(Annealing test (for copper) IS 10810 : Part 1)	-	0	-
Cl 17.2(Conductor resistance test IS 10810 : Part 5)	-	0	-
Cl 17.1(Persulphate test (tinned copper conductor) IS 10810 : Part 4)	-	0	-
Cl 17.2(Tensile strength before ageing on insulation IS 10810 : Part 7)	-	0	-
Cl 17.2(elongation at break before ageing on insulation IS 10810 : Part 7)	-	0	-
Cl 17.2(Tensile strength after Ageing in air bomb IS 10810 : Part 56)	-	0	-
Cl 17.2(Elongation after Ageing in air bomb IS 10810 : Part 56)	-	0	-
Cl 17.2(Tensile strength variation)	-	0	-
Cl 17.2(Elongation Variation)	-	0	-
Cl 17.2(Hot set elongation on insulation IS 10810 : Part 30)	-	0	-
Cl 17.2(Permanent elongation (set) on insulation IS 10810 : Part 30)	-	0	-
Cl 17.1(Tensile strength before ageing on sheath IS 10810 : Part 7)	-	0	-
Cl 17.1(elongation at break before ageing on sheath IS 10810 : Part 7)	-	0	-
Cl 17.1(Hot set elongation test on sheath IS 10810 : Part 30)	-	0	-
Cl 17.1(Permanent elongation (set) test on sheath IS 10810 : Part 30)	-	0	-
Cl 17.1(Oxygen index test on sheath IS 10810 : Part 58)	-	0	-
Cl 17.1(Temperature index test on sheath IS 10810 : Part 64)	-	0	-
Cl 17.1(Acid gas generation on sheath IS 10810 : Part 39)	-	0	-
Cl 17.2(Insulation resistance test IS 10810 : Part 43)	-	0	-
Cl 17.1(Water absorption test (for insulation) IS 10810 : Part 28)	-	0	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	0	-
Cl 18.2(High Voltage Test IS 10810 : Part 45)	-	0	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	25000	-
Cl 18.3 Annex B of IS 16246( Circuit Integrity Test Under Fire Condition)	-	25000	-
Cl 18.4.1( Flame Retardence Test on Single Cable IS 10810 : Part 61)	-	15000	-
Cl 18.4.2(Flame Retardence Test on Bunched Cables IS 10810 : Part 63)	-	0	-
Cl 19.1( Manufacturer’s Identification)	-	0	-
Cl 19.2( Voltage Identification)	-	0	-
Cl 19.3( Cable Identification)	-	0	-
Cl 19.4( Cable Code)	-	0	-

11 Mar, 2028

-
Included w.e.f. 16.06.2026

IS 17505 : Part 1 (2021)

Specification for Thermosetting Insulated Fire Survival Cables for Fixed Installation having Low Emission of Smoke and Corrosive Gases when Affected by Fire for Working Voltages upto and including 1100 Vac and 1500 Vdc

100000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.3, Table 1 to 5 of IS 8130:2013 & IS:10810 (Part 5)-1984(Conductor Resistance Test)	-	0	-
Cl. 7.1.2 of IS 8130 : 2013 & IS:10810 (Part 1)-1984(Annealing Test (for copper))	-	0	-
Cl. 7.1.1 of IS 8130:2013 & IS:10810 (Part 4)-1984(Persulphate Test for tinned copper)	-	0	-
IS 191:2007 & IS 440(Copper purity test)	-	10000	-
Cl. 11,14,16, Table 4 and Table 6 of IS 17505 & IS:10810 (Part 6)-1984(Test for overall dimensions and thickness of insulation and sheath)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 36)-1984(Diameter of armour Wire)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 37)-1984(Tensile strength and elongation at break)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 38)-1984(Torsion Test on galvanised steel wire for armouring)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 39)-1984(Winding Test for Formed Wires)	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 40)-1984(Uniformity of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 41)-1984(Mass of Zinc coating on Round Steel Wires and Formed Steel Wires (Strips))	-	0	-
Table 7 of IS 17505-1:2021, IS 3975:1999 & IS:10810 (Part 42)-1984(Resistivity test)	-	0	-
Table 1 and Table 2 of IS 17505 -1: 2021, IS:10810 (Part 7)-1984 & IS:10810 (Part 11)-1984(Tensile Strength and elongation at break before and after ageing.)	-	0	-
Cl 18.2 of IS 17505-1:2021 & IS:10810 (Part 45)-1984(High voltage test)	-	0	-
Table 1 of IS 17505-1 :2021 & IS:10810 (Part 43)-1984(Insulation Resistance)	-	0	-
Cl. 18.6 of IS 17505-1:2021 & IS:10810 (Part 58)-1998(Oxygen index)	-	0	-
Cl. 18.7 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	0	-
Table-1 & Table-2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Specification for thermosetting insulated fire survival cables for fixed installation having low emission of smoke and corrosive gases when affected by fire for working voltages upto and including 1100 V A.C. and 1500 V D.C(Hot deformation)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	5000	-
Table-1 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	5000	-
Table 1 of IS 17505-1: 2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 30)-1984(Hot set test)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone Resistance test)	-	20000	-
Cl 18.5.1 of IS 17505-1 :2021 & IS:10810 (Part 61)-1988(Flame test on single cable)	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	10000	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 7)-1984(Tensile strength and elongation at break.)	-	0	-
Tabel 1 and 2 of IS 17505-1:2021 & IS:10810 (Part 11)-1984(Ageing in air oven.)	-	0	-
Cl 18.6 of IS 17505-1: 2021 & IS:10810 (Part 58)-1998(Oxygen Index.)	-	0	-
Cl 18.8 of IS 17505-1:2021 & IS:10810 (Part 64)-2003(Temperature Index)	-	0	-
Table 1 & 2 of IS 17505-1: 2021 & IS:10810 (Part 13)-1984(Ozone resistance test)	-	20000	-
Table 2 of IS 17505-1:2021 & IS:10810 (Part 15)-1984(Hot deformation)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(pH)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Conductivity)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(HCl and HBr)	-	0	-
Cl 7 & Annex-F (F.1, F.2, F.3 F.4) of IS 17505-1 :2021(Presence of Fluorine / Fluorine Content (if required))	-	0	-
Table 1 of IS 17505-1:2021 & IS:10810 (Part 12)-1984(Shrinkage test)	-	0	-
Cl 18.2of IS 17505-1:2021 & IS:10810 (Part 45)-1984.(High Voltage test.)	-	0	-
Cl 18.5of IS 17505-1:2021 & IS:10810 (Part 53)-1984(Flammability Test)	-	0	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 20)-1984(Cold bend test)	-	0	-
Table-2 of IS 17505-1:2021 & IS:10810 (Part 21)-1984(Cold impact test)	-	0	-
Cl 18.5 of IS 17505-1:2021 & IS:10810 (Part 61)-1988(Flammability Test)	-	0	-
Cl 18.9 of IS 17505-1:2021(Water immersion test ( effect of water on sheath of cable))	-	0	-
Cl 18.8 of IS 17505-1:2021& IS:10810 (Part 63)-1993(Smoke density test)	-	0	-
Cl. 3.5, 18.4 & Annex-E of IS 17505-1:2021(Circuit integrity test under fire)	-	0	-
Cl. 17.1 Table 9 (iv) e(Heat Shock)	-	0	-
Cl. 17.1 Table 9 (iv) h(Water absorption (Gravimetric))	-	0	-
Cl. 17.1 Table 9 (vii) b(Flame test on bunched cable)	-	0	-
Cl. 17.1 Table 9 (ix)(Abrasion resistance test)	-	10000	-
Cl. 17.1 Table 9 (iv) m(Assessment of Halogen (HCl))	-	5000	-

11 Mar, 2028

-
Included w.e.f 04.06.2026

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

70000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	0	-
4.1.1 b) (Material : Seperator tape )	-	0	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	0	-
4.1.1 e) (Shape of conductor )	-	0	-
4.1.1 f) (Nominal size of conductor )	-	0	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	0	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	0	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	0	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	0	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	0	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	0	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	0	-
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	0	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.3(Fillers)	-	0	-
4.4(Binder Tape)	-	0	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	0	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	0	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	0	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	0	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	0	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	0	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	0	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	0	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	0	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	0	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	0	-
4.5.6, 13.4(Colour of Sheath)	-	0	-
5.1(High Voltage Test (at Room Temperature))	-	0	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	0	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	0	-
5.5(Temperature Index-IS 10810 (Part 64).)	-	0	-
5.6(Smoke Density-IS 10810 (Part 63).)	-	0	-
5.7(Assessment of Halogen- Table 1 of Annex D)	-	0	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	0	-
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	0	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	0	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	0	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	0	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	0	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	0	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	0	-
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	0	-
6.1, Table 1(CORE IDENTIFICATION)	-	0	-
6.2(Core Identification by Numbers)	-	0	-
6.2.1(Preferred Arrangement of Marking)	-	0	-
6.2.2(Durability)	-	0	-
7.0(CABLE CODE)	-	0	-
9.0( IDENTIFICATION)	-	0	-
10.1(Packing )	-	0	-
10.2(marking)	-	0	-
10.2.1(Standards marking)	-	0	-
13.3, 14.3(assembly of cores )	-	0	-
6.1(General Requirements)	-	0	-
6.1.1(Colour Combination Green Yellow)	-	0	-
12.1(Conductor)	-	0	-
12.2, Table 4(insulation)	-	0	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	0	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	0	-
4.3.1 (c)(Conductivity test (Fillers))	-	0	-
4.3.1 (b)(pH test (Fillers))	-	0	-
4.3.1 (a)(HCl test (Fillers))	-	0	-
5.7 (a)(HCl test (Assessment of halogen test))	-	10000	-
5.7 (b)(pH test (Assessment of halogen test))	-	5000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	10000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	20000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	20000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	0	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	0	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	0	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	0	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	0	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	0	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	0	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	0	-
Table 2, III a (i)(Conductor Resistance)	-	0	-
Annex A(Hot Deformation)	-	0	-
5.2(Spark Test (Routine Test))	-	0	-

11 Mar, 2028

-
Included w.e.f 04.06.2026

IS 398 : Part 6 (2021)

Aluminium Conductors For Overhead Transmission Purposes Part 6: High conductivity aluminium alloy stranded conductors

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.2(Visual Examination)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.4, Table 2(Measurement of Diameter of Individual Aluminium Alloy Wires)	-	0	-
16.5, Table 2(Breaking Load Test - before stranding)	-	0	-
16.5, Table 2(Breaking Load Test - after stranding)	-	0	-
16.6, Table 1(Elongation Test - before stranding)	-	0	-
16.6, Table 1(Elongation Test - after stranding)	-	0	-
16.7, Table 2(Resistivity Test)	-	0	-
16.8(Wrapping Test)	-	0	-
11(Stranding)	-	0	-
8(Freedom from defects)	-	0	-
16.9, Table 3(Ultimate Tensile Strength on Stranded Conductor)	-	0	-
16.10, Table 3(d.c. Resistance Test on Stranded Conductor)	-	0	-
16.11(Stress-strain Test)	-	0	-
Cl-5(MATERIAL COMPOSITION)	-	0	-
Cl-7, Table-1(Diameter of Wire (mm))	-	0	-
Cl-7, Table-1(Minimum Tensile Strength of Wire)	-	0	-
Cl-7, Table-1(Minimum Elongation on 250 mm (percent))	-	0	-
Cl-8(Freedom from Defects)	-	0	-
Cl-9.1.1(Wires-Nominal Sizes)	-	0	-
Cl-9.2.1(Stranded Conductors- Size)	-	0	-
Cl-10(Joints in Wires)	-	0	-
16.2(Visual Examination)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.4, Table 2(Measurement of Diameter of Individual Aluminium Alloy Wires)	-	0	-
16.5, Table 2(Breaking Load Test - before stranding)	-	0	-
16.5, Table 2(Breaking Load Test - after stranding)	-	0	-
16.6, Table 1(Elongation Test - before stranding)	-	0	-
16.6, Table 1(Elongation Test - after stranding)	-	0	-
16.7, Table 2(Resistivity Test)	-	0	-
16.8(Wrapping Test)	-	0	-
11(Stranding)	-	0	-
8(Freedom from defects)	-	0	-
16.9, Table 3(Ultimate Tensile Strength on Stranded Conductor)	-	25000	-
16.10, Table 3(d.c. Resistance Test on Stranded Conductor)	-	0	-
16.11(Stress-strain Test)	-	25000	-
Cl-5(MATERIAL COMPOSITION)	-	0	-
Cl-7, Table-1(Diameter of Wire (mm))	-	0	-
Cl-7, Table-1(Minimum Tensile Strength of Wire)	-	0	-
Cl-7, Table-1(Minimum Elongation on 250 mm (percent))	-	0	-
Cl-8(Freedom from Defects)	-	0	-
Cl-9.1.1(Wires-Nominal Sizes)	-	0	-
Cl-9.2.1(Stranded Conductors- Size)	-	0	-
Cl-10(Joints in Wires)	-	0	-
16.2(Visual Examination)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.4, Table 2(Measurement of Diameter of Individual Aluminium Alloy Wires)	-	0	-
16.5, Table 2(Breaking Load Test - before stranding)	-	0	-
16.5, Table 2(Breaking Load Test - after stranding)	-	0	-
16.6, Table 1(Elongation Test - before stranding)	-	0	-
16.6, Table 1(Elongation Test - after stranding)	-	0	-
16.7, Table 2(Resistivity Test)	-	0	-
16.8(Wrapping Test)	-	0	-
11(Stranding)	-	0	-
8(Freedom from defects)	-	0	-
16.9, Table 3(Ultimate Tensile Strength on Stranded Conductor)	-	25000	-
16.10, Table 3(d.c. Resistance Test on Stranded Conductor)	-	0	-
16.11(Stress-strain Test)	-	25000	-
Cl-5(MATERIAL COMPOSITION)	-	0	-
Cl-7, Table-1(Diameter of Wire (mm))	-	0	-
Cl-7, Table-1(Minimum Tensile Strength of Wire)	-	0	-
Cl-7, Table-1(Minimum Elongation on 250 mm (percent))	-	0	-
Cl-8(Freedom from Defects)	-	0	-
Cl-9.1.1(Wires-Nominal Sizes)	-	0	-
Cl-9.2.1(Stranded Conductors- Size)	-	0	-
Cl-10(Joints in Wires)	-	0	-
16.2(Visual Examination)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.3, Table 4(Measurement of Lay Ratio / Direction of Lay)	-	0	-
16.4, Table 2(Measurement of Diameter of Individual Aluminium Alloy Wires)	-	0	-
16.5, Table 2(Breaking Load Test - before stranding)	-	0	-
16.5, Table 2(Breaking Load Test - after stranding)	-	0	-
16.6, Table 1(Elongation Test - before stranding)	-	0	-
16.6, Table 1(Elongation Test - after stranding)	-	0	-
16.7, Table 2(Resistivity Test)	-	0	-
16.8(Wrapping Test)	-	0	-
11(Stranding)	-	0	-
8(Freedom from defects)	-	0	-
16.9, Table 3(Ultimate Tensile Strength on Stranded Conductor)	-	25000	-
16.10, Table 3(d.c. Resistance Test on Stranded Conductor)	-	0	-
16.11(Stress-strain Test)	-	25000	-
Cl-5(MATERIAL COMPOSITION)	-	0	-
Cl-7, Table-1(Diameter of Wire (mm))	-	0	-
Cl-7, Table-1(Minimum Tensile Strength of Wire)	-	0	-
Cl-7, Table-1(Minimum Elongation on 250 mm (percent))	-	0	-
Cl-8(Freedom from Defects)	-	0	-
Cl-9.1.1(Wires-Nominal Sizes)	-	0	-
Cl-9.2.1(Stranded Conductors- Size)	-	0	-
Cl-10(Joints in Wires)	-	0	-

11 Mar, 2028

-
Included w.e.f 04.06.2026

IS 9968 : Part 1 (2025)

Elastomer Insulated Cables - Specification Part 1 for Working Voltages up to and including 1100 volts (Second Revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Copper Conductor)	-	0	-
Cl-4.2(Aluminum Conductor)	-	0	-
Cl-6.1(Proofed Tape)	-	0	-
Cl-6.2("Polyethylene Terephthalate (PETP) Tape or Plastic Tape or Any Other Suitable Tape")	-	0	-
Cl-6.3(Glass Tape)	-	0	-
Cl-7(Fillers)	-	0	-
Cl-8.1(Textile Braid)	-	0	-
Cl-8.2(Glass Braid)	-	0	-
Cl-9.1(General Service Insulated Cables and Flexible Cords)	-	0	-
Cl-9.2(Heat Resisting Insulated Cables)	-	0	-
Cl-9.3(Silicon Rubber Insulated Cable)	-	0	-
Cl-10.1(Preservative Compound)	-	0	-
Cl-10.2(Varnish)	-	0	-
Cl-12(separator tape)	-	0	-
Cl-14(Core Identification)	-	0	-
Cl-18(Laying UP of Cores)	-	0	-
Cl-19(Binder Tape)	-	0	-
Cl-20.2(Thickness of Sheath)	-	500	-
Cl-20.3(Tolerance on Thickness of Sheath)	-	500	-
Cl-20.4(Colour)	-	0	-
Cl-22.1 (i) (a)(Conductor resistance test)	-	500	-
Cl-22.1 (i) (b)(High voltage test or spark test.)	-	500	-
Cl-22.1 (ii) (a)(Annealing test (for copper);)	-	500	-
Cl-22.1 (ii) (b)(Tensile Test ((for aluminium);)	-	500	-
Cl-22.1 (ii) (c)(Wrapping test (for aluminium);)	-	500	-
Cl-22.1 (ii) (f)(Tensile strength and elongation at break of insulation and sheath)	-	500	-
Cl-22.1 (ii) (g)(Hot set test for insulation and sheath)	-	1000	-
Cl-22.1 (ii) (h)(High voltage test)	-	500	-
Cl-22.1 (ii) (i)(Insulation resistance test)	-	1000	-
Cl-22.1 (iii) (a)(Persulphate test (for tinned copper);)	-	500	-
Cl-22.1 (iii) (f)(Test for thickness of insulation and sheath and overall diameter)	-	500	-
Electrical(Tensile strength and elongation at break)	-	500	-
Cl-22.1 (iii) (g), 2(Ageing in air oven)	-	500	-
Cl-22.1 (iii) (g), 3(Ageing in air bomb)	-	500	-
Cl-22.1 (iii) (g), 4(Ageing In oxygen bomb)	-	1000	-
Cl-22.1 (iii) (g), 5(Hot set)	-	1000	-
Cl-22.1 (iii) (g), 6(Oil resistance;)	-	500	-
Cl-22.1 (iii) (g), 7(Tear resistance)	-	500	-
Cl-22.1 (iii) (i)(High voltage (water immersion) test;)	-	500	-
Cl-22.1 (iii) (j)(Flammability test)	-	500	-
Cl-22.1 (iii) (k)(Water absorption test (for insulation as applicable))	-	500	-
Cl-24.1(Manufacturer’s Identification)	-	0	-
Cl-25(Packing and Morning)	-	0	-

11 Mar, 2028

-
Included w.e.f. 01.04.2026

IS 398 : Part 2 (2025)

Aluminium Conductor for Overhead Transmission Purposes - Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced (Fourth Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Material)	-	500	Rs. 7000/- Up to 100 Sq.mm
Cl-6.1.1(chemical composition of high carbon steel)	-	1000	-
Cl-6.2(zinc used for galvanizing)	-	1000	-
Cl-7(Freedom From Defects)	-	500	-
Cl-8.1(Wires-Nominal Sizes)	-	1000	-
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	1000	-
Cl-9.1(Joint in Wires)	-	500	-
Cl-9.2(Aluminium Wires)	-	1000	-
Cl-9.3(Galvanized Steel Wires)	-	1000	-
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	1000	-
Cl-13.3(Conductor- Visual examination)	-	1000	-
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	1000	-
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	1000	-
Cl- 13.14(Conductor- Ultimate tensile strength test on stranded conductor)	-	0	-
Cl- 13.13(Conductor- Surface condition test on stranded conductor)	-	0	-
Cl- 13.15(Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.))	-	0	-
Cl-13.16(Conductor- Radio interference voltage test)	-	0	-
Cl-13.4(Aluminium wires-Measurement of diameter)	-	1000	-
Cl- 13.6(Aluminium wires -Breaking load test)	-	1000	-
Cl- 13.8(Aluminium wires- Wrapping test)	-	1000	-
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	1000	-
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	1000	-
Cl- 13.4(Steel wires- Measurement of diameter)	-	1000	-
Cl- 13.6(Steel wires- Breaking load test)	-	1000	-
Cl- 13.7(Steel wires- Ductility test)	-	1000	-
Cl- 13.8(Steel wires- Wrapping test)	-	1000	-
Cl- 13.10(Steel wires- Galvanizing test)	-	1000	-
Cl-13.7.1(Torsion Test)	-	1000	-
Cl-13.7.2(Elongation Test)	-	1000	-
Cl-11.1(Standard Length)	-	500	-
Cl-11.2(Random Lengths)	-	500	-

11 Mar, 2028

-
-

IS 7098 : Part 1 (2025)

Crosslinked Polyethylene Insulated Thermoplastic Sheathed Cables - Specification Part 1 For Working Voltages up to and Including 1 100 Volts (Second Revision)

65000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Conductors -Material)	-	1000	Rs. 15000/- for Cat. C1, Rs. 30000/- for Cat. C2, Rs. 65000/- for Cat. C3, Rs. 1000/- for each Additional core, Rs. 2000/- for optional test, Rs. 3000/- for armour test
Cl-5, Table-1 (i)(Tensile strength)	-	1000	-
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	5000	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	5000	-
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	5000	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	2000	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	2000	-
Cl-5, Table-1 (iv)(Shrinkage)	-	1000	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	5000	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	2000	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	2000	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	1000	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	1000	-
Cl-7(Armouring)	-	1000	-
Cl-8(Outer Sheath)	-	1000	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	2000	-
Cl-11(Core Identification)	-	1000	-
Cl-12(Laying up of Cores)	-	1000	-
Cl-13(Inner Sheath (Common Covering))	-	1000	-
Cl-14.1(Armouring- Application)	-	1000	-
Cl-14.1.2(armour round wires/formed wires)	-	1000	-
Cl-14.2(Type of Armour)	-	1000	-
Cl-14.3(Dimensions)	-	2000	-
Cl-14.4(Joints)	-	1000	-
Cl-14.5(Resistance)	-	2000	-
Cl-15.3(Thickness of Outer Sheath)	-	2000	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	2000	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	2000	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	2000	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	2000	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	2000	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	2000	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	2000	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	2000	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	2000	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	2000	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	2000	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	2000	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	2000	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	5000	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	5000	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	2000	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	1000	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	2000	-
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	1000	-
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	2000	-
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	2000	-
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	5000	-
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	1000	-
Cl-17.2(High voltage test)	-	2000	-
Cl-17.3(Flammability test)	-	2000	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	5000	-
Cl-17.5(Flame retardance test on single cable)	-	5000	-
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	5000	-
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	5000	-
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	5000	-
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	5000	-
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	5000	-
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	5000	-
Cl-16.4 (i)(Cold bend test for outer sheath)	-	2000	-
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	2000	-
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	2000	-

11 Mar, 2028

-
Included w.e.f 08.12.2025

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Marking)	-	500	-
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	500	-
6.3(Standard Mark on Conduit)	-	500	-
7.1.1(Maximum and minimum outside diameter of socket)	-	500	-
7.1.1 Table-2(Length of Socket end)	-	500	-
7.1.2(Maximum and minimum outside diameter of conduit)	-	500	-
7.2(Minimum inside diameter of conduit)	-	500	-
7.3(Length of conduit)	-	500	-
7.4(Unifomity of The wall Thickness)	-	500	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500	-
9.2(Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-	500	-
9.3(Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-	500	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	500	-
9.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	500	-
10(Resistance to Heat -Ball presure test)	-	1000	-
11(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	1000	-
12(Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1000	-
12(Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1000	-
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	1000	-
13(Tests for external influence as per clause 13 of IS: 9537 (Part 1)-1980)	-	1000	-
12(3 Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-	1000	-
12(3 Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-	1000	-
11.0(Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-	1000	-
10.0(Resistance to Heat -Ball presure test)	-	1000	-
9.5 Fig.5(Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-	500	-
9.4(Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-	500	-
9.3(Compression Test (after removal of force) as per caluse 9.3.3 of IS: 9537 (Part 1)-1980)	-	1000	-
9.3(Compression Test at Full force applied (On load))	-	1000	-
9.2(Bending Test At Low Temp (-5 ±2°C))	-	1000	-
9.2(Bending Test At Room Temp)	-	500	-
8.1(Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-	500	-
7.4(Unifomity of The wall Thickness)	-	1000	-
7.3(Length of conduit)	-	500	-
7.2 Fig.3(Minimum inside diameter of conduit)	-	500	-
7.1.2 Fig.2(Minimum outside diameter of conduit)	-	500	-
7.1.2 Fig.1(Maximum outside diameter of conduit)	-	500	-
7.1.1 Table-2(Length of Socket end)	-	500	-
7.1.1 Fig.8(Maximum inside diameter of socket)	-	500	-
7.1.1 Fig.7(Maximum outside diameter of socket)	-	500	-
6.3(Standard Mark on Conduit)	-	500	-
6.2(Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-	500	-
6.1 - d(Marking)	-	500	-
6.1 - c(Marking)	-	500	-
6.1 - b(Marking)	-	500	-
6.1 - a(Marking)	-	500	-

11 Mar, 2028

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

11500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	500	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	500	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	500	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
6.1(MATERIALS : ARMGURING)	-	500	-
6.2(MATERIALS : ARMGURING)	-	500	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	500	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	500	-
8.1(CONSTRUCTION : CONDUCTOR)	-	500	-
8.2(CONSTRUCTION : CONDUCTOR)	-	500	-
9.1(INSULATION )	-	500	-
9.2(INSULATION : Thickness of Insulation)	-	1000	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	1000	-
9.4(INSULATION : Application of Insulation)	-	500	-
10.1(CORE IDENTIFICATION)	-	500	-
10.2(CORE IDENTIFICATION)	-	500	-
10.3(CORE IDENTIFICATION)	-	500	-
10.3.1(Arrangement of Marking)	-	500	-
11.1(LAYING UP OF CORES)	-	500	-
11.2(LAYING UP OF CORES)	-	500	-
12.1(INNER SHEATH)	-	500	-
12.2(INNER SHEATH)	-	500	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	1000	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	1000	-
13.1.1(ARMOURING : Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1000	-
13.1.3(ARMOURING : Direction of lay )	-	500	-
13.1.4(ARMOURING : Application)	-	500	-
13.2(ARMOURING : Type of Armour)	-	500	-
13.2.1(ARMOURING : Type of Armour)	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(ARMOURING : Joints)	-	500	-
13.5.1(ARMOURING : Resistance)	-	1000	-
13.5.2(ARMOURING : Resistance)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	500	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	500	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(OUTER SHEATH)	-	500	-
14.2(OUTER SHEATH)	-	500	-
14.3(OUTER SHEATH : Colour )	-	500	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	1000	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	1000	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	500	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	1000	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	1000	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	1000	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	2000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	2000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2000	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 d)4)(Hot deformation : Insulation )	-	1000	-
15.1 d)4)(Hot deformation : Sheath )	-	1000	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	2000	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	2000	-
15.1 d)6)(Heat shock test- Insulation )	-	1000	-
15.1 d)6)(Heat shock test- sheath )	-	1000	-
15.1 d)7)(Thermal stability- insulation )	-	1000	-
15.1 d)7)(Thermal stability- Sheath )	-	1000	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	1000	-
15.1 e)(Insulation resistance test : IR Constant )	-	1000	-
15.1 f)(High voltage test ( water immersion test ))	-	1000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	1000	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	1000	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	1000	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	1000	-
16.1(DETAILS OF TESTS : General)	-	500	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	500	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1000	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	2000	-
16.4(Flammability Test)	-	1000	-
16.5(Oxygen Index Test)	-	3000	-
16.6(Flame Retardance Test on Single Cables)	-	1000	-
16.7(Flame Retardance Test on Bunched Cables)	-	5000	-
16.9(Test for Halogen Acid Gas Evolution)	-	3000	-
16.1(Temperature Index)	-	3000	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	500	-
17.2(IDENTIFICATION : Cable Identification)	-	500	-
17.2.1(IDENTIFICATION : Cable Identification)	-	500	-
17.3(IDENTIFICATION : Cable Code)	-	500	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	-
16.4(Flammability Test- Un affected portion)	-	1000	-
16.4(Flammability Test- Period of Burning)	-	1000	-
9.3(Minimum Thickness of Reduce core insulation)	-	1000	-
9.2(Thickness of Reduce core insulation)	-	1000	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	500	-
Cl No. 16.10(Smoke density test)	-	3000	-
Cl No. 16.8(Test for specific optical density of smoke)	-	5000	-
Table 4(Copper purity test)	-	3000	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Conductor, Number of wires.)	-	500	-
Cl.8(Flexibility class)	-	500	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	2000	-

11 Mar, 2028

-
-

IS 9968 : Part 1 (1988)

Specification for elastomer insulatedcables: Part 1 for working voltages up to and including 1100 volts (First Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1( Copper Cooduetor)	-	500	-
3.2(Aluminium conductor)	-	500	-
4.1(INSULATION : lnsulation for General Service)	-	500	-
4.2(INSULATION : Heat Resisting insulation)	-	500	-
4.3(INSULATION : Silicone Rubber Insulation)	-	500	-
5.1(TAPE : Proofed Tape)	-	500	-
5.2(TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-	500	-
5.3(TAPE : Giass Tape)	-	500	-
6.1(FILLERS : )	-	500	-
7.1(BRAID : Textile Braid)	-	500	-
7.2(BRAID : Glass Braid )	-	500	-
8.1(SHEATH : General Service Insulated Cables and Flexible Cords)	-	500	-
8.2(SHEATH :Heat Resisting Insulated Cables)	-	500	-
9.1(PresenRtive Compound)	-	500	-
9.2(Varnish)	-	500	-
10( Conductor )	-	500	-
11(Separator tape)	-	500	-
12.2(Insulation : Thickness of Insufatien)	-	1000	-
12.4(Insulation : Allplication of Insulation)	-	500	-
13(CORE IDENTiFICATlON)	-	500	-
14(Tape)	-	500	-
15(BRAIDING)	-	500	-
16(COMPOUNDING AND VARNISHING)	-	500	-
17(LAYING UP OF CORES)	-	500	-
18( Binder tape)	-	500	-
19.2(Sheath : Thickness of Sheath)	-	1000	-
19.4( Sheath :Colour)	-	500	-
20( Overall diameter)	-	1000	-
21. (a)(Persulphate tests (for copper))	-	1000	-
21. (b)(Annealing Test (for coper))	-	500	-
21. (c)( Tensile Test (for aluminium))	-	500	-
21. (d)( Wrapping Test (for aluminium))	-	500	-
21. (e)(Conductor Resistance )	-	1000	-
21.1( Tensile strength )	-	1000	-
22.1( Elongation)	-	1000	-
21.1(type test : Ageing In air oven)	-	2000	-
21.1(type test : Ageing in air bomb)	-	2000	-
21.1(type test : Ageing In oxygen bomb)	-	2000	-
21.1(type test : Hot set elongation)	-	2000	-
21.1(type test : Tear resistance )	-	1000	-
22.2(type test :Insulauon resistance High voltage (water immersron ) test)	-	1000	-
22.2(type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-	1000	-
21(Water absorption test)	-	3000	-
23(identification)	-	500	-
Cl No. 4.1(Ageing in oxygen bomb - Elongation)	-	2000	-
Cl No. 4.1(Ageing in oxygen bomb - Tensile strength )	-	2000	-
Cl No. 4.1(Ageing in air bomb - Elongation)	-	2000	-
Cl No. 4.1(Ageing in air bomb - Tensile strength )	-	2000	-
Cl No. 4.1(Ageing in air oven - Elongation)	-	2000	-
Cl No. 4.1(Ageing in air oven - Tensile strength )	-	2000	-
Cl No. 22.2(High Voltage Test (Water Immersion))	-	1000	-
Cl No. 4.1(Insulation resistance)	-	1000	-
Cl No. 22.4, Appendix B (Flexing test for cords for use with electric iron )	-	2000	-
Cl No. 22.2.2/22.2.3(High Voltage Test / Spark test)	-	1000	-
Cl No. 23.1, 23.2(Identification)	-	500	-
21.1((f) Oil resistance)	-	2000	-
Cl.9.1(Compound and Varnish)	-	500	-
Cl.9.2(Compound and Varnish)	-	500	-
Cl.21.1 & Table 2 of IS: 6380-1984(Water Absorption Test)	-	3000	-
Cl.19.1(Application of Sheath)	-	500	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Without Ageing))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Without Ageing))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Without Ageing))	-	1000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air oven))	-	2000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air oven))	-	2000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air Bomb ))	-	2000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (After ageing in air Bomb ))	-	2000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Oil Resistance Test ))	-	2000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Oil Resistance Test ) Variation on Elongation (Percentage))	-	2000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Hot Set Test))	-	2000	-
Cl.21.1 & Table 3 of IS: 6380-1984(Physical Test on outer sheath (Hot Set Test))	-	2000	-
Cl.21.1 & Table 2 of IS: 6380-1984(Insulation Resistance Test)	-	1000	-
Cl.21.1 & Table 2 of IS: 6380-1984(Insulation Resistance Test)	-	1000	-

11 Mar, 2028

-
-

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	500	-
7.1 Table-1(Dimensional measurement of wires)	-	500	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	1000	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	1000	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	1000	-
9.1(Stranding)	-	500	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	-
9.3(Direction of Lay)	-	500	-
9.4(Multiple layers of wires)	-	500	-
11(Packing and Marking)	-	500	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	1000	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	1000	-
12.3 Table 1(Elongation Test- Before Stranding)	-	1000	-
12.3 Table 1(Elongation Test- After Stranding)	-	1000	-
12.4 Table 1(Resistance of Aluminium wire)	-	1000	-
9.2(Lay Ratio 24 wire layer)	-	500	-
9.2(Lay Ratio 18 wire layer)	-	500	-
9.2(Lay Ratio 12 wire layer)	-	500	-
9.2(Lay Ratio 3/6 wire layer)	-	500	-
7.2.1(Sizes)	-	500	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	1000	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	1000	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	1000	-

11 Mar, 2028

-
-

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (elec)(Stranding)	-	500	-
10 (mech)(Stranding)	-	500	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires Before Stranding)	-	500	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (mech)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (mech)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.2 (elec)(Ductility by Elongation Test before stranding)	-	500	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	500	-
13.5.1 (mech)(Wrapping Test Aluminium Wires Before Stranding)	-	500	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	500	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	500	-
13.5.2 (mech)(Wrapping Test Galvanized Steel Wires After Stranding)	-	500	-
13.6 (elec)(Resistance test-Aluminium wire before Stranding)	-	1000	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	1000	-
13.7.2 (chem)(Mass of Zinc coating)	-	1000	-
13.7.2 (chem)(Uniformity of Zinc coating)	-	1000	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Outermost Layer)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	500	-
13.8 Table-4 (mech)(Lay Ratio- Steel Core (6 Wire Layer))	-	500	-
13.9 (elec)(Surface condition test)	-	0	-
13.10 (elec)(Ultimate breaking load)	-	0	-
13.11 (elec)(Stress-strain test)	-	0	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	500	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	500	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	500	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	500	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	500	-
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	500	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1000	-
13.7.2 (elec)(Mass of Zinc coating)	-	1000	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	500	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires Before Stranding)	-	500	-
13.5.1 (elec)(Wrapping Test Aluminium Wires After Stranding)	-	500	-
13.5.1 (elec)(Wrapping Test Aluminium Wires Before Stranding)	-	500	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1 (elec)(Ductility by Torsion Test before stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1 (elec)(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
10 (elec)(Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires After Stranding)	-	500	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires After Stranding)	-	500	-
8.1.1 & 13.2 Table 2 (elec)(Diameter of Steel Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table-1 (elec)(Diameter of Aluminium Wires Before Stranding)	-	500	-
4.1(Resistivity)	-	1000	-
4.2(Density)	-	500	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5.1(Density)	-	1000	-
5.2(Coefficient of Linear Expansion)	-	1000	-
14.2(a), 8.2.1(Sizes)	-	500	-
7(FREEDOM FROM DEFECTS)	-	1000	-
6.2(zinc Purity)	-	1000	-
9(Joint in wires)	-	500	-
6.1.1(Aluminum wires shall conform to IS 5484)	-	500	-
6.1.2(The mechanical properties of wire shall comply with the requirements given in Table 2)	-	1000	-
6.2(It shall conform to and satisfy all the requirements of IS 209)	-	500	-
8.2.2(Calculated resistance)	-	1000	-
Cl-9.2.5(Welded joint strength)	-	1000	-
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table 2(Diameter of Steel Wires Before Stranding)	-	500	-
8.1.1 & 13.2 Table-1(Diameter of Aluminium Wires After Stranding)	-	500	-
8.1.1 & 13.2 Table 2(Diameter of Steel Wires After Stranding)	-	500	-
10(Stranding)	-	500	-
13.3 Table 1(Breaking Load of Aluminium Wires Before Stranding)	-	1000	-
13.3 Table 2(Breaking Load of Steel Wires Before Stranding)	-	1000	-
13.3 Table 1(Breaking Load of Aluminium Wires After Stranding)	-	1000	-
13.3 Table 2(Breaking Load of Steel Wires After Stranding)	-	1000	-
13.4.1(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1(Ductility by Torsion Test before stranding)	-	1000	-
13.4.1(Ductility by Torsion Test after stranding)	-	1000	-
13.4.1(Ductility by Torsion Test after stranding)	-	1000	-
13.5.1(Wrapping Test Aluminium Wires Before Stranding)	-	500	-
13.5.1(Wrapping Test Aluminium Wires After Stranding)	-	500	-
13.5.2(Wrapping Test Galvanized Steel Wires Before Stranding)	-	500	-
13.8 Table-4(Lay Ratio- Aluminium Wire Outermost Layer)	-	500	-
13.8 Table-4(Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-	500	-
13.8 Table-4(Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-	500	-
13.8 Table-4(Lay Ratio- Steel Core (6 Wire Layer))	-	500	-
13.7(Galvanising test Dip test for uniformity of coating)	-	1000	-
13.7(Galvanising test Dip test for uniformity of coating)	-	1000	-
13.7(Weight of Zinc Coating [g/m²])	-	1000	-
13.7(Weight of Zinc Coating [g/m²])	-	1000	-
7.1(Freedom from Defects)	-	1000	-
9(Joint in Wire)	-	1000	-
13.5.2(Wrapping Test Galvanized Steel Wires After Stranding)	-	500	-

11 Mar, 2028

-
Exclusion: Cl.13.9 (Surface condition test), Cl.13.10 (Ultimate breaking load), Cl.13.11 (Stress-Strain test)

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	1000	-
12.3, Table-1(Breaking load before stranding)	-	1000	-
12.3, Table-1(Breaking load after stranding)	-	1000	-
12.4(Wrapping test)	-	1000	-
12.5, Table 1(Resistance test)	-	1000	-
12.6, Table 3(Measurement of lay ratio)	-	1000	-
9.3(Stranding)	-	500	-
6(Freedom from defects)	-	500	-
7.2.1(Sizes)	-	500	-
8, 8.1, 8.2(Joint in wires, except during stranding)	-	500	-
9.2(Lay ratio)	-	1000	-
9.4(Multiple layer of wires)	-	500	-
4.1(Resistivity)	-	1000	-
4.2(Density)	-	1000	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5(Material)	-	500	-
7.1.1(Nominal Sizes)	-	500	-
7.2.2(Resistance)	-	1000	-

11 Mar, 2028

-
-

IS 9857 (1990)

Welding cables - Specification (First Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor : Material )	-	500	-
5(SEPARATOR)	-	500	-
6(COVERING)	-	500	-
7(CONDUCTOR : CONSTRUCTION )	-	500	-
8(S E P A R A T O R)	-	500	-
9.1(C O V E R I N G : Application )	-	500	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	500	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	500	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	500	-
9.5(Colour of C o v e r i n g)	-	500	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	500	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	1000	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	1000	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	1000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	2000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	2000	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	2000	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	2000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	2000	-
10.1 c) 5)(Hot set test )	-	1000	-
10.1 c) 5)(Permanent set )	-	1000	-
11.1(High Voltage Test ( Water Immersion Test ))	-	1000	-
11.2(Spark Test)	-	500	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	1000	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-
12.3(Cable Code)	-	500	-
13.1(Packing )	-	500	-
13.2(Marking)	-	500	-
14(CABLE RATINGS)	-	500	-
15(VOLTAGE DROP)	-	500	-
Table 4(Copper purity test)	-	2000	-
Table 2(Oil resistance - Elongation)	-	2000	-
Table 2(Oil resistance - Tensile strength )	-	2000	-
Table 2(Ageing in air bomb - Elongation)	-	2000	-
Table 2(Ageing in air bomb - Tensile strength )	-	2000	-
Table 1 (Thickness of covering)	-	1000	-
15.1 (d)(Heat Shock Test)	-	1000	-
15.1 (d)(Hot Deformation Test)	-	1000	-
15.1 (d)(Loss Of Mass Test)	-	2000	-
10.1(b), Table 1(Thickness of covering)	-	1000	-

11 Mar, 2028

-
-

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	1000	-
9.3(Thickness of Insulation - Minimum)	-	1000	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	1000	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	1500	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(Armour: Joint)	-	500	-
13.5(Armouring : Resistance Test)	-	1000	-
13.6 a)(ARMOURING: Tensile Strength)	-	1000	-
13.6 b)(ARMOURING: Elongation )	-	1000	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	1000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	500	-
14.2(Colour of outer sheath)	-	500	-
14.3(Thickness of outer sheath - minimum)	-	1000	-
15.1 a) i)(Annealing Test ( For copper wire ) )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	1000	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	1000	-
15.1 a) iii)(Wrapping test (for aluminium))	-	1000	-
15.1 a) iv)(Resistance test - Main conductor)	-	1000	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	1000	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	1000	-
15.1 d) ii) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	2000	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	2000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	2000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	1000	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	1000	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	5000	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	1000	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	1000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	2000	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	2000	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	2000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	1000	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	1000	-
15.1 e) v) (Sheath : Hot deformation)	-	2000	-
15.1 e) vi) (Sheath : Heat shock test)	-	1000	-
15.1 e) vii) (Sheath : Thermalstability)	-	1000	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	2000	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	1000	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	1000	-
16.9(Oxygen Index Test)	-	3000	-
16.1(Flame Retardance Test on Single Cables)	-	1000	-
16.11(Flame Retardance Test on Bunched Cables)	-	5000	-
16.13(Test for Halogen Acid Gas Evolution)	-	3000	-
16.14(Temperature Index)	-	2000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	1000	-
15.4 (b)(Cold impact)	-	1000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 4(Copper purity test)	-	2500	-
Cl No. 16.15(Smoke density test)	-	2000	-
Table 2(Cold Impact test for Outer sheath)	-	1000	-
Table 2(Cold bend test for Outer sheath)	-	1000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl 16(Halogen Acid Gas Test)	-	2000	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.8(Conductor)	-	500	-
Cl.15.4(Cold Bend Test (for outer sheath))	-	1000	-
Cl.15.4(Cold Impact Test (For outer sheath))	-	1000	-
Cl.13.5.1 and Table 7(Resistance Test for Armouring (other than mining Cables))	-	1000	-
14.3(Thickness of outer sheath - AVERAGE)	-	1000	-

11 Mar, 2028

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	500	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	500	-
5.1(Insulation)	-	500	-
6.1(Flexibility class)	-	500	-
6.2(Compactness)	-	500	-
6.2(No of strands)	-	500	-
6.2(Surface)	-	500	-
6.3(Protective barrier)	-	500	-
6.4(size of street lighting conductor)	-	500	-
6.5(Size of messenger conductor )	-	500	-
6.6(Joints in messenger conductor )	-	500	-
6.6(Direction of outer layer)	-	500	-
7.1(Insulation)	-	500	-
7.2( Thickness of insulation)	-	1000	-
7.3(Tolerance on thickness of insulation )	-	1000	-
7.4(Aplication of the insulation )	-	500	-
7.5(Colour of the insulation )	-	500	-
8.1(Core identification)	-	500	-
8.2(Core identification)	-	500	-
8.3(Identification by other means)	-	500	-
9.1(Assembly (Laying up))	-	500	-
9.2(Assembly (Laying up))	-	500	-
9.3(Direction of lay)	-	500	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	1000	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	1000	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	1000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	1000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	1000	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	1000	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	1000	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	2000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	2000	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	1000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	1000	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	1000	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	1000	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	3000	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	2000	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	2000	-
10.1 g)(High voltage test - IS10810:Part 45)	-	1000	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	1000	-
11.4(Bending Test on the Completed Cable ( Optional))	-	1000	-
6.1(Construction of phase conductor)	-	500	-
6.1(Number of wires (phase conductor))	-	500	-
6.1(Construction of Street Lighting conductor)	-	500	-
6.1(Number of wires (Street Lighting conductor))	-	500	-
12.1(Manufacturer's Identification)	-	500	-
12.2(Cable Identification)	-	500	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	1000	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	1000	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	1000	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	1000	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	1000	-
10.1 d) iii)(Carbon Black Content)	-	2000	-

11 Mar, 2028

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	500	-
11.2(Legibility)	-	500	-
11.1(Durability)	-	500	-
11(Identification)	-	500	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	3000	-
10.4(Flammability test- Unaffected portion)	-	1000	-
10.4(Flammability test-Burning after flame removal)	-	1000	-
table 1 e) 3) (IR constant- max. Temp)	-	1000	-
table 1 e) 3) (IR constant- Room temp )	-	1000	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	1000	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	1000	-
10.2(HV (room temperature))	-	1000	-
10.1(HV (water immersion))	-	2000	-
10.1(HV (water immersion))	-	2000	-
10.8(Smoke density rating)	-	2000	-
10.6(Halogen evolution)	-	2000	-
10.7(Temperature index)	-	2000	-
10.5(Oxygen index)	-	2000	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	1000	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	1000	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	1000	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	1000	-
Table 1(Category Code)	-	500	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	1000	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	2000	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	1000	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	1000	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	1000	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	1000	-
Table 1 iii) d) 4)(Cracks Observed)	-	1000	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	1000	-
Table 1 iii) c) 4)(Cracks Observed)	-	1000	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	1000	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	2000	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	2000	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	2000	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	2000	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	2000	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	2000	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	1000	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	1000	-
Table 1 iii) c) 3)(Elongation variation)	-	2000	-
Table 1 iii) c) 3)(TS variation)	-	2000	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	2000	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	2000	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	1000	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	1000	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	500	-
8.3(Thickness of Sheath)	-	1000	-
5.2(Application )	-	500	-
5.3(Thickness of Insulation)	-	1000	-
9.1(Ovality)	-	1000	-
9(Overall dimensions)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	1000	-
4.2(Conductor resistance test)	-	1000	-
4.1(Wrapping test (for Al))	-	1000	-
4.1(Tensile test (for Al)- After Stranding)	-	1000	-
4.1(Tensile test (for Al)-Before Stranding)	-	1000	-
4.1(Annealing test (for copper))	-	1000	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	500	-
12(CONSTRUCTION Core Identification)	-	500	-
8.1(Sheath Material )	-	500	-
7(Binder Tape)	-	500	-
6.2(Filler)	-	500	-
6.1(Filler)	-	500	-
5.1(Insulation)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.1(Conductor - Material)	-	500	-
4.1(Conductor - Material)	-	500	-
10.11(Persulphate Test )	-	2000	-
12.0(Core identification)	-	500	-
4, IS 8130(Construction of conductor)	-	500	-
Table 2, IS 8130(No fo wire in a conductor)	-	500	-
8.3(Minimum thickness of Sheath)	-	1000	-
8.3(Avarage thickness of Sheath)	-	1000	-
5.3(Minimum thickness of insulation)	-	1000	-
5.3(Avarage thickness of insulation)	-	1000	-
table 1, 4.2(insulation resistance test)	-	1000	-
5.4(Mechanical properties before and after ageing)	-	2000	-
4.1(Material)	-	500	-
4.2(Electrical Resistance)	-	1000	-
5(INSULATION)	-	500	-
6(FILLER)	-	500	-
7(BINDER TAPE)	-	500	-
8(SHEATH)	-	500	-
9(OVERALL DIMENSIONS)	-	1000	-
10.1(High Voltage Test (Water Immersion Test))	-	2000	-
10.2(High Voltage Test (at Room Temperature))	-	1000	-
10.4(Flammability Test)	-	1000	-
10.5(Oxygen Index Test)	-	2000	-
10.6(Test for Halogen Acid Gas Evolution)	-	2000	-
10.7(Test for Temperature Index)	-	2000	-
10.8(Smoke Density Rating)	-	2000	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	2000	-
10.1(Flex Test)	-	1000	-
10.11(Persulphate Test)	-	1000	-
11(IDENTIFICATION)	-	500	-
12(CORE IDENTIFICATION)	-	500	-
13(CABLE CODE)	-	500	-
15(PACKING AND MARKING)	-	500	-
16.1(Construction)	-	500	-
16.2(Tests)	-	500	-
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	500	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	500	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	500	-
(4.3 of IS 8130:2013)(Form of Conductor)	-	500	-
( 4.4.1 of IS 8130:2013)(Joints in Conductor)	-	500	-
(4.4.2 of IS 8130:2013)(Joints in Conductor Solid Conductors (Aluminium Conductors only))	-	500	-
(Cl.6.1.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.2 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(6.2.1 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.2 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.2.3 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	500	-
(6.3.1 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.2 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
(6.3.3 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	500	-
( 6.4.1 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
(6.4.2 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
( 6.4.3 of IS 8130:2013)(Flexible Conductors (Class 5))	-	500	-
Cl.19.1.4(Assembly of Cores)	-	500	-
Cl. 8.2(Application of Sheath)	-	500	-
10.3(Spark Test)	-	1000	-
10.3(Spark test)	-	1000	-
Table 4(Copper purity test)	-	2500	-
10.3(Spark Test)	-	1000	-

11 Mar, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

Global Testing Laboratory Private limited, Ghaziabad

Plot No.55,Gali No.5A, Rajendra Nagar Industrial Area, Mohan Nagar Ghaziabad, Uttar Pradesh, Ghaziabad, Uttar Pradesh, 201007

8368402864 info@globaltestinglaboratory.com

Scope List