BIS - LIMS (Laboratory Information Management System)

Nextron International Lab Private Limited

G-45, Pocket-C, Sector-4, Bawana, North West, Delhi, 110039

8437033522 gulia.gaurav@yahoo.com

Scope List

Reset

9 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 15644 (2006)

Safety of electric toys

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Marking and instructions)	-	200	-
8.0(Power Input)	-	800	-
9.0(Heating and abnormal operation)	-	800	-
10.0(Electrical strength at operating temperature)	-	800	-
11.1(Moisture resistance)	-	500	-
11.2(Resistant to humidity)	-	1000	-
12.0(Electric strength at room temperature)	-	800	-
13.0(Mechanical strength)	-	300	-
14.1(Construction)	-	100	-
14.2(Construction)	-	100	-
14.3(Construction)	-	100	-
14.4(Construction)	-	100	-
14.5(Construction)	-	100	-
14.6(Construction)	-	100	-
14.7(Construction)	-	100	-
14.8(Construction)	-	100	-
14.9(Construction)	-	100	-
14.1(Construction)	-	100	-
14.11(Construction)	-	100	-
14.12(Construction)	-	100	-
14.13(Construction)	-	100	-
14.14(Construction)	-	100	-
15.1(Protection of cords and wires)	-	500	-
15.2(Protection of cords and wires)	-	500	-
16.0(Components)	-	1000	-
17 Table-1(Screws and connections)	-	200	-
17 Table-1(Nominal daimeter of screws made of insulating material)	-	200	-
18.0(Clearance and creepage distance)	-	500	-
19.1(Ball pressure test IEC 60695-10-2)	-	500	-
19.2.1(Glow wire test IEC 60695-2-11)	-	500	-
19.2.2(Needle flame test)	-	500	-
20.0(Radiation, toxicity and similar hazards)	-	1000	-

Complete

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1.5(Components)	-	1000	-
1.6(Power interface .)	-	1500	-
1.7(Markings and instructions)	-	400	-
2.1(Protection from electric shock and energy hazards)	-	4000	-
2.2(SELV circuits)	-	900	-
2.3(TNV circuits)	-	1000	-
2.4(Limited current circuits)	-	1400	-
2.5(Limited power sources .)	-	400	-
2.6(Provisions for earthing and bonding)	-	4000	-
2.7(Overcurrent and earth fault protection in primary circuits)	-	4000	-
2.8(Safety interlocks)	-	900	-
2.9(Electrical insulation)	-	4000	-
2.10(Clearances, creepage distances and distances through insulation)	-	2400	-
3.1(General)	-	800	-
3.2(Connection to a mains supply)	-	800	-
3.3(Wiring terminals for connection of external conductors)	-	1500	-
3.4(Disconnection from the mains supply)	-	800	-
3.5(Interconnection of equipment)	-	800	-
4.1(Stability)	-	800	-
4.2(Mechanical strength)	-	800	-
4.3(Design and construction)	-	800	-
4.4(Protection against hazardous moving parts)	-	1000	-
4.5(Thermal requirements)	-	3000	-
4.6(Openings in enclosures)	-	1000	-
4.7(Resistance to fire)	-	2000	-
5.1(Touch current and protective conductor curren)	-	1000	-
5.2(Electric strength)	-	2000	-
5.3(Abnormal operating and fault conditions)	-	1000	-
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment)	-	1500	-
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	1500	-
6.3(Protection of the telecommunication wiring system from overheating)	-	1000	-
7.1(General)	-	1000	-
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment)	-	1000	-
7.3(Protection of equipment users from overvoltages on the cable distribution system)	-	1000	-
7.4(Insulation between primary circuits and cable distribution systems)	-	600	-

Complete

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1500	-
8(Protection against accidental contact with live parts)	-	1500	-
9(Terminals)	-	1000	-
10(PROVISION FOR EARTHING)	-	1000	-
11(MOISTURE RESISTANCE)	-	3000	-
12(Electric Strength)	-	1000	-
13(Thermal endurance test for winding of ballasts)	-	1000	-
14(Fault conditions)	-	2000	-
15(Transformer heating)	-	2000	-
16(Construction)	-	1000	-
17(Creepage distance and clearances)	-	1000	-
18(Screws, current carrying parts and connections)	-	1000	-
19(Resistance to heat, fire and tracking)	-	2000	-
20(Resistance to corrosion)	-	1000	-

Complete

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	2000	-
6(Interchangeability)	-	1000	-
7(Protection against accidental contact with live parts)	-	2000	-
8(Insulation Resistance and Electric Strength)	-	3000	-
9(MECHANICAL STRENGTH)	-	2000	-
10(cap temperature)	-	3000	-
11(Resistance to Heat)	-	2000	-
12(Resistance to Flame and Ignition)	-	1000	-
13(Fault conditions)	-	2000	-
14(Creepage distance and clearances)	-	2000	-

Complete

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	4000	-
7(Heating under normal operating conditions)	-	5000	-
8(Constructional requirements with regard to the protection against electric shock)	-	4000	-
9(Electric shock hazard under normal operating conditions)	-	4000	-
10(Insulation requirements)	-	8000	-
11(Fault conditions)	-	3000	-
12(Mechanical strength)	-	3000	-
13(CLEARANCES and CREEPAGE DISTANCES)	-	5000	-
15(TERMINALS)	-	2000	-
16(External flexible cords)	-	2000	-
17(Electrical connections and mechanical fixings)	-	2000	-
19(Stability and mechanical hazards)	-	5000	-
20(Resistance to fire)	-	3000	-

Complete

IS 9873 : Part 2 (2017)

Safety of toys: Part 2 flammability (Third Revision)

3216 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2-5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	625	-
4.2.2(a)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-	625	-
4.2.2(b)-5.2(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-	625	-
4.2.3-5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	625	-
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-	625	-
4.2.4-5.3(Toys to be worn on the head-Full or partial moulded head masks-maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	625	-
4.5-5.5(Soft-filled toys-rate of spread of flame )	-	625	-
4.5-5.5(Soft-filled toys-Test for soft-filled toys )	-	625	-
4.2.5-5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	625	-
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	625	-
4.3-5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	625	-
4.4-5.4(Toys intended to be entered by a child-rate of spread of flame)	-	625	-
4.1(General)	-	625	-
4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	625	-
4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-	625	-

Complete

IS 16046 : Part 1 (2018)

Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 1 Nickel Systems ( Second Revision )

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Parameter Measurement Tolerances)	-	1000	-
5(General Safety Considerations)	-	500	-
5.1(General)	-	500	-
5.2(Insulation and Wiring)	-	500	-
5.3(Venting)	-	500	-
5.4(Temperature, Voltage and Current Management)	-	500	-
5.5(Terminal Contacts)	-	500	-
5.6(Assembly of Cells into batteries)	-	500	-
5.7(Quality Plan)	-	500	-
6(Tyoe Test amd Sample Size)	-	5000	-
7(Specific requirements and tests)	-	3000	-
7.1(Charging procedure for test purposes)	-	3000	-
7.2(Intended Use)	-	3000	-
7.3(Reasonably foreseeable misuse)	-	3000	-
8(Information for safety)	-	1500	-
8.1(General)	-	1500	-
8.2(Small Cell and battery safety information)	-	1500	-
9.1(Cell Marking)	-	1250	-
9.2(Battery Marking)	-	1250	-
9.3(Caution for ingestion of small cells and batteries)	-	1250	-
9.4(Other information)	-	1250	-
10(Packaging)	-	8500	-

Complete

IS 16046 : Part 2 (2018)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Parameter Measurement Tolerances)	-	1000	-
5(General Safety Considerations)	-	450	-
5.1(General)	-	450	-
5.2(Insulation and Wiring)	-	450	-
5.3(Venting)	-	450	-
5.4(Temperature, Voltage and Current Management)	-	450	-
5.5(Terminal Contacts)	-	450	-
5.6(Assembly of Cells into batteries)	-	450	-
5.7(Quality Plan)	-	450	-
5.8(Battery Safety Components)	-	450	-
6(Type Test and Sample Size)	-	4000	-
7(Specific requirements and tests)	-	1000	-
7.1(Charging procedure for test purposes)	-	4000	-
7.2(Intended Use)	-	4000	-
7.3(Reasonably foreseeable misuse)	-	4000	-
8(Information for safety)	-	1000	-
8.1(General)	-	1500	-
8.2(Small Cell and battery safety information)	-	1500	-
9(Marking)	-	1000	-
9.1(Cell Marking)	-	1000	-
9.2(Battery Marking)	-	1000	-
9.3(Caution for ingestion of small cells and batteries)	-	1000	-
9.4(Other information)	-	1000	-
10(Packaging)	-	8950	-

Complete

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	120	-
9873 (Part - 1) 4.2.5 - 5.4(Toys to be worn on the head-Flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks)-rate of spread of flame)	-	120	-
9873 (Part - 1) 4.2.4 - 5.3(Toys to be worn on the head-Full or partial moulded head masks-Duration of the flame after the removal of the test flame)	-	120	-
9873 (Part - 1) 4.2.3 - 5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy- maximum distance between the upper edge of the burnt area and the point of application of the test flame)	-	120	-
9873 (Part - 1) 4.2.3 - 5.3(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude less than 50 mm and more than 5 mm from the surface of the toy-Duration of the flame after the removal of the test flame)	-	120	-
9873 (Part - 1) 4.2.2(b) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was less than 150 mm)	-	120	-
9873 (Part - 1) 4.2.2(a) - 5.3(Toys to be worn on the head-Test relating to Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy- if ignition occurs, the maximum burnt length of hair, pile, or material that behaves in a similar manner when the initial length was 150 mm or more)	-	120	-
9873 (Part - 1) 4.2.2 - 5.2(Toys to be worn on the head-Beards, moustaches, wigs, etc. made from hair, pile, or material that behaves in a similar manner to hair (e.g. free-hanging ribbons, paper, cloth strands, or other flowing elements), which protrude 50 mm or more from the surface of the toy-Duration of the flame after the removal of the test flame)	-	120	-
9873 (Part - 1) 4.35.3 - 5.39(Jaw entrapment in handles and steering wheels-jaw entrapment test)	-	120	-
9873 (Part - 1) 4.33 - 5.11.3(Straps intended to be worn fully or partially around the neck-breakaway feature separation test)	-	120	-
9873 (Part - 1) 4.32 - 5.38.1( Yo-yo balls - The ratio of the mass m (in grams) to the elastic constant k of the yo-yo ball tether(m/k))	-	120	-
9873 (Part - 1) 4.32 - 5.38.2( Yo-yo balls - length (lo) of the yo-yo ball tether)	-	120	-
9873 (Part - 1) 4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test After Following tests: -tension test for magnets; -drop test/tip over test for large and bulky toys; -torque test; -tension test, general procedure; -tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable; -impact test for magnets; -compression test; -tension test for magnets;)	-	120	-
9873 (Part - 1) 4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index After Following tests: -tension test for magnets; -drop test/tip over test for large and bulky toys; -torque test; -tension test, general procedure; -tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable; -impact test for magnets; -compression test; -tension test for magnets;)	-	120	-
9873 (Part - 1) 4.31.2(b) - 5.34 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-soaking test for magnets-small parts test)	-	120	-
9873 (Part - 1) 4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test)	-	120	-
9873 (Part - 1) 4.31.1 - 5.32(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-magnetic flux index)	-	120	-
9873 (Part - 1) 4.30.5(f) - 5.30( Toy scooters-Adjustable and folding steering tubes and handlebars-resistance to separation of handlebar)	-	120	-
9873 (Part - 1) 4.30.6 - 5.28( Toy scooters-Braking- force required to hold the toy)	-	120	-
9873 (Part - 1) 4.30.4 - 5.12.2(Toy scooters-Stability-sideways stability test, feet available for stabilization)	-	120	-
9873 (Part - 1) 4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes)	-	120	-
9873 (Part - 1) 4.30.3 - 5.27(Toy scooters-Strength-dynamic strength for toy scooters)	-	120	-
9873 (Part - 1) 4.30.3 - 5.27 - 5.9(Toy scooters-Strength-dynamic strength for toy scooters-sharp-point test)	-	120	-
9873 (Part - 1) 4.30.3 - 5.27 - 5.8(Toy scooters-Strength-dynamic strength for toy scooters- sharp-edge test)	-	120	-
4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters)	-	120	-
9873 (Part - 1) 4.30.3 - 5.26 - 5.9(Toy scooters-Strength-static strength for toy scooters-sharp-point test)	-	120	-
9873 (Part - 1) 4.30.3 - 5.26 - 5.8(Toy scooters-Strength-After static strength for toy scooters- sharp edge test)	-	120	-
9873 (Part - 1) 4.26(c ) - 5.20 - 5.2( Mouth-actuated toys-small parts test after durability of mouth-actuated toys)	-	120	-
9873 (Part - 1) 4.26(b) - 5.24.6.1 - 5.4( Mouth-actuated toys-small parts test after tension test, general procedure)	-	120	-
9873 (Part - 1) 4.26(b) - 5.24.5 - 5.3( Mouth-actuated toys-small parts test after torque test)	-	120	-
9873 (Part - 1) 4.26(a) - 5.2( Mouth-actuated toys-small parts test)	-	120	-
9873 (Part - 1) 4.25 - 5.19(Liquid-filled toys-leakage of liquid-filled toys)	-	120	-
9873 (Part - 1) 4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy( Parts made of other materials))	-	120	-
9873 (Part - 1) 4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of Plastic or wood ))	-	120	-
9873 (Part - 1) 4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of glass or porcelain))	-	120	-
9873 (Part - 1) 4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand-(Parts made of metals))	-	120	-
9873 (Part - 1) 4.23 - 5.17(Speed limitation of electrically driven ride-on toys-determination of speed of electrically driven ride-on toys)	-	120	-
9873 (Part - 1) 4.22.3 - 5.16.3(Toy bicycles-Braking requirements- brake performance for toy bicycles)	-	120	-
9873 (Part - 1) 4.22.3 - 5.16.1(Toy bicycles-Braking requirements-determination of free-wheeling facility)	-	120	-
9873 (Part - 1) 4.18.4.6 - 5.24.6.4 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-kinetic energy per area After tension test for protective components)	-	120	-
9873 (Part - 1) 4.18.4.6 - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After tension test for protective components)	-	120	-
9873 (Part - 1) 4.18.4.6 - 5.24.5 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set- kinetic energy per area After torque test)	-	120	-
9873 (Part - 1) 4.18.4.6 - 5.24.5(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set-After torque test)	-	120	-
9873 (Part - 1) 4.18.4.3 - 5.15.2(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-wall impact test for projectiles)	-	120	-
9873 (Part - 1) 4.18.3(c ) - 5.24.6.4(Projectile toys-Projectile toys with stored energy- tension test for protective components)	-	120	-
9873 (Part - 1) 4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After torque test)	-	120	-
9873 (Part - 1) 4.18.4.2(a) - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-determination of the kinetic energy per area of contact when the contact area of the dart shall be at least 3 cm^2)	-	120	-
9873 (Part - 1) 4.18.4.1 - 5.20(Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys)	-	120	-
9873 (Part - 1) 4.18.3(d) - 5.15.2(Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles)	-	120	-
9873 (Part - 1) 4.18.3(c ) - 5.24.5(Projectile toys-Projectile toys with stored energy-torque test)	-	120	-
9873 (Part - 1) 4.18.3(b) - 5.15.1.3.3(Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact)	-	120	-
9873 (Part - 1) 4.18.3(a) - 5.4(Projectile toys-Projectile toys with stored energy--small parts test after (wall impact test for projectiles)	-	120	-
9873 (Part - 1) 4.18.3(a) - 5.3 - 5.24(Projectile toys-Projectile toys with stored energy-small parts test after reasonably foreseeable abuse testing)	-	120	-
9873 (Part - 1) 4.18.2 - e - 5.24.6.5(Projectile toys-Projectiles-tension test for a projectile with a suction cup)	-	120	-
9873 (Part - 1) 4.18.2(d) - 5.37 - 5.24.6.5(Projectile toys-Projectiles-length of suction cup projectiles After tension test for a projectile with a suction cup)	-	120	-
9873 (Part - 1) 4.18.2(d) - 5.37 - 5.24.5(Projectile toys-Projectiles-length of suction cup projectiles After torque test)	-	120	-
9873 (Part - 1) 4.18.2(a) - 5.36(Projectile toys-Projectiles-tip assessment of rigid projectiles)	-	120	-
9873 (Part - 1) 4.17 - 5.14(Simulated protective equipment, such as helmets, hats and goggles-Impact test for toys that cover the face)	-	120	-
9873 (Part - 1) 4.16.2.2(c) - 5.13.2.2 - 4.12.3(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Hinge line clearance)	-	120	-
9873 (Part - 1) 4.16.2.2(a) - 5.13.2.1(Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support)	-	120	-
9873 (Part - 1) 4.16.2.1 - 5.13.1(Enclosures-Closures-Lids, doors and similar devices-Test For closures)	-	120	-
9873 (Part - 1) 4.15.3 - 5.12.6( Stability and overload requirements-Stability of stationary floor toy-Stability test of stationary floor toys)	-	120	-
9873 (Part - 1) 4.15.2 - 5.24.4( Stability and overload requirements-Overload requirements for ride-on toys and seats-dynamic strength test for wheeled ride-on toys other than toy scooters)	-	120	-
9873 (Part - 1) 4.15.2 - 5.12.5( Stability and overload requirements-Overload requirements for ride-on toys and seats-overload test for ride-on toys and seats)	-	120	-
9873 (Part - 1) 4.15.1.3 - 5.12.4( Stability and overload requirements-Stability of ride-on toys and seats-Fore and aft stability Test)	-	120	-
9873 (Part - 1) 4.15.1.2 - 5.12.3( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet unavailable for stabilization)	-	120	-
9873 (Part - 1) 4.13.3 - 5.7(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys-accessibility of a part or component)	-	120	-
9873 (Part - 1) 4.12.2 (a) - 5.22.3(Folding mechanisms-Other toys with folding mechanisms)	-	120	-
9873 (Part - 1) 4.12.1(b - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	120	-
9873 (Part - 1) 4.11.11 - 5.11.6(Cords, strings and lines for flying toys- electrical resistance)	-	120	-
9873 (Part - 1) 4.11.8 - 5.11.5(Cords- Self-retracting cords intended for children under 36 months-self-retracting cords)	-	120	-
9873 (Part - 1) 4.11.7 - 5.11.1(Cords- Diameter of certain cords intended for children under 36 months-cords cross-sectional dimension)	-	120	-
9873 (Part - 1) 4.11.5 - 5.11.2(Cords-Cords on pull toys-free length)	-	120	-
9873 (Part - 1) 4.11.4(a) - 5.11.4.2(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Elastic materials)	-	120	-
9873 (Part - 1) 4.11.4(a) - 5.11.4.1(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Head probe push test)	-	120	-
9873 (Part - 1) 4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys- individual thickness)	-	120	-
9873 (Part - 1) 4.5.4 - 5.6(Shape, size and strength of certain toys- Pre-school play figures-Test for pre-school play figures)	-	120	-
9873 (Part - 1) 4.5.3 - 5.5(Shape, size and strength of certain toys-Pompoms-Test for pompoms)	-	120	-
9873 (Part - 1) 4.3.2 - 5.21( Expanding materials)	-	120	-
9873 (Part - 1) 4.2 - 5.24.8.3( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent)	-	120	-
9873 (Part - 1) 4.2 - 5.24.8.2( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent)	-	120	-
9873 (Part - 1) 4.2 - 5.24.7( Reasonably foreseeable abuse -Compression test)	-	120	-
9873 (Part - 1) 4.2 - 5.24.6.3( Reasonably foreseeable abuse -Tension test for pompoms)	-	120	-
9873 (Part - 1) 4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 3) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	120	-

Complete

Bureau of Indian Standards

The National Standards Body of India

Nextron International Lab Private Limited

G-45, Pocket-C, Sector-4, Bawana, North West, Delhi, 110039

8437033522 gulia.gaurav@yahoo.com

Scope List