BIS - LIMS (Laboratory Information Management System)

CIPET, Ahmedabad

Plot No. 630, Phase-IV, GIDC, Vatva,, Ahmedabad, Ahmadabad, Gujarat, 382445

7229000205 cipetahmd@gmail.com

Scope List

Reset

39 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

20319 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	500	for all Dimensions
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	500	for all Dimensions
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	500	for all Dimensions
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	500	for all Dimensions
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	500	for all Dimensions
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	500	for all Dimensions
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	500	for all Dimensions
7.1.4(Length)	-	500	for all Dimensions
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	500	for all Dimensions
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	500	for all Dimensions
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	500	for all Dimensions
7.2.1.1 Table3(Angle of taper (Note-1))	-	500	for all Dimensions
9.1(PIPE ENDS)	-	150	-
10.1(Surface Finish)	-	150	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	900	with specimen preparation charges
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
10.7(Sulphated Ash Content)	-	950	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5000	-
11.2(Resistance to External Blows at 0°C)	-	1400	with specimen preparation charges
13(Marking)	-	300	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	for all Dimensions
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	for all Dimensions
10.3(Effect on Water Test)	-	3000	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	-	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	-	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	-	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	-	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	-	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	-	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	-	-
7.1.4(Length)	-	-	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	-	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	-	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	-	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	-	-
9.1(PIPE ENDS)	-	-	-
10.1(Colour)	-	-	-
10.1(Surface Finish)	-	-	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	-	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	-	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	-	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	-	-
10.7(Sulphated Ash Content)	-	-	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	-	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	-	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	-	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	-	-
11.2(Resistance to External Blows at 0°C)	-	-	-
13(Marking)	-	-	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	-	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	-	-
10.3(Effect on Water Test)	-	-	-

Complete

31 Dec, 2024

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

27568 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Mass of Bale)	-	250	4.2,5.1,5.2, 5.3,5.4
5.2 Table 1(Dimensions)	-	250	4.2,5.1,5.2, 5.3,5.4
5.2 Table 1(Ends per dm)	-	250	4.2,5.1,5.2, 5.3,5.4
5.2 Table 1(Picks per dm)	-	250	4.2,5.1,5.2, 5.3,5.4
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	250	4.2,5.1,5.2, 5.3,5.4
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	1350	1100+250
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	1350	1100+250
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1350	1100+250
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	0
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	0
5.2 Table 1(Drop impact strength)	-	1100	0
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	950	0
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	950	0
5.2 Table 1(Dimensions)	-	250	0
5.2 Table 1(Dimensions)	-	250	0
5.2 Table 1(Dimensions)	-	250	0

Complete

31 Dec, 2024

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

23394 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.2(Resistance to External Blows at 0°C)	-	1000	300
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	0
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	5000	0
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	0
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	0
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	700	200
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	0
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	0
9.1(PIPE ENDS)	-	0	0
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	0
Clause 10.7(Sulphated Ash Content)	-	950	0
10.1(Colour)	-	300	0

Complete

31 Dec, 2024

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

152694 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	500	7.1.1, 7.1.2, 7.1.3
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	0	Included in 7.1.1
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	0	Included in 7.1.1
7.1.3 (Effective length)	-	0	Included in 7.1.1
8(Pipe Ends)	-	300	8, 9.1
9.1(Visual Appearance)	-	0	Included in 9.1
9.2 IS 12235 (Part 3)(Opacity)	-	575	0
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	3000	9.3
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	9.3
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	9.3
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	9.3
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	9.3
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	9.3
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	9.3
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	700	0
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1100	0
9.6 IS 12235(Part 14)(Density)	-	500	0
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	850	20°C /1 h.
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	4800	95°C /165 h
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	11000	95°C /1000 h
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	1000	1000+109500
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	1100	1100+300
10.4 IS 12235(Part 19)(Flattening Test)	-	500	0
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	1100	1100+500
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	11000	11000+300
6.3(K value Test)	-	1100	0
6.2.1 Annex B(Chloride Content of Resin)	-	4300	0
6.3.1 Annex B(Chloride content)	-	4300	0
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	500	0

Complete

31 Dec, 2024

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

33275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	0
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	0
7.2.1 (Visual and Workmanship Requirement)	-	300	0
3.0(Reversion test)	-	700	700+300
3.0(Tensile strength at yield)	-	1100	1100+250
3.0((ii)Acceptance Test at 3.8MPa induced stress for 48 hours at 80°C)	-	1600	0
3.0((i)Quality Test at 3.5MPa induced stress for 165 hours at 80°C)	-	4800	0
4.1.1.2.1(Density)	-	500	0
4.1.1.2.1(MFI @ 1900C/5.0 Kg)	-	1100	0
4.1.5(a. Identification of Rubber Ring)	-	1050	0
4.1.5(b. Colour of rubber ring)	-	300	0
4.1.5(c. Change in hardness after keeping it in air at 70°C for 7 days)	-	375	0
6.1.1, 6.1.1.1(Leakage Test)	-	850	0
6.1.2.2( Hydraulic Proof Test)	-	850	0
Cl.6.1.3(Weldability Test- b) Acceptance test)	-	1600	0
Cl.6.1.3(Weldability Test- a) Quality test)	-	4800	0

Complete

31 Dec, 2024

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

11594 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.2(K-Value as per IS-4669)	-	1100	0
4.1.1 (VCM Content as per IS 10151 (Annex A))	-	3000	0
8.4(Sealing rings - Hardness)	-	375	0
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	0
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	0
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	0
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	0
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	0
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	0
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	0	0
9.1(Visual Appearance)	-	300	0
9.2(Internal Diameter)	-	350	0
9.3(Density IS 12235 (Part 14))	-	500	0
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1100	1100+300
9.5(Tensile Strength IS 12235(Part 13))	-	1100	1100+500
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	0
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000	0

Complete

31 Dec, 2024

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

38700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.2(Colour)	-	250	0
6.2.1(6.1.1 Identification Stripes)	-	250	0
7()	-	300	0
7.2(Length)	-	500	0
7.4 table -3 & 4(6.1 Dimensions)	-	0	0
7.4.1.2(Ovality)	-	0	0
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	1600+4000+4800+11000
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	0
8.2(Longitudinal Reversion Test)	-	700	0
8.3(Carbon black)	-	925	0
8.4( Melt Flow Rate)	-	1100	0
8.5 (Oxidation Induction Time)	-	2200	0
8.6(Overall migration)	-	1700	0
8.7(Density)	-	500	0
8.8(Tensile Strength for Butt-fusion)	-	1100	1100+250
8.9 table-6(Elongation at Break)	-	1100	0
8.10(Slow Crack Growth Rate)	-	5500	0
5.2(Density)	-	500	0
5.2(MFI @ 1900C/5.0 Kg)	-	1100	0
5.2(Volatile matter Content)	-	700	0

Complete

31 Dec, 2024

IS 14885 (2001)

Polyethylene pipes for the supply of gaseous fuels - Specification

356175 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.4(Colour)	-	0		0
6.1, Table-3(Ovality Pipe, Cl 6.3.2)	-	0		0
6.1, Table-3(Nominal Outside Diameter of Pipes , Cl 6.3.1)	-	0		0
6.2.1, Table-4(Minimum Wall Thickness, Cl.6.3, Cl.6.2.1.1, Table-5)	-	0		0
6.4(Length of pipe)	-	0		0
7, Table-6(Maximmn Out of Square of Each Pipe End)	-	0		0
8.1(Hydraulic Charactristics, Annex-A)	-	0		0
8.2(Reversion Test. Annex-C)	-	0		0
8.3(Density, Annex A of IS 7328)	-	0		0
8.4(Melt Flow Rate (MFR), IS 2530)	-	0		0
8.7(Tensile yield strength, Annex-J)	-	0		0
8.7(Elongation at break, Annex-J)	-	0		0
8.5(Thermal Stability to Oxidation, Annex-D)	-	0		0
8.8(Resistance to Weathering, Annex-F)	-	0		0
8.9(Squeeze off, Annex-G)	-	0		0
8.6 & Table-2(Volatile Content: Annex-H of IS 14885)	-	0		0
8.5 & Table-2(Thermal Stability to Oxidation, Annex-D of IS 14885)	-	0		0
Table-2, 5.1(Conventional Density, IS 7328:1992)	-	0		0
Table-2, 5.1(Melt Flow Rate, IS 2530:1963)	-	0		0
Table-2, 5.1(Thermal Staibility, Annex-D)	-	0		0
Table-2, 5.1(Resistance to gas constituents, Cl 5.5)	-	0		0
Table-2, 5.1(Pigment dispersion, Annex-E)	-	0		0

Complete

31 Dec, 2024

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

18150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1200	Tio2
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	500	6.1.1, 6.1.2, 6.1.3 & 6.1.4
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	0	Included in 6.1
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	0	Included in 6.1
6.1.3 (Length of Pipe)	-	0	Included in 6.1
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	0	Included in 6.1
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	0	Included in 6.1
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	0	Included in 6.1
6.1.4, Table 3(iv) Length of spigot, l1)	-	0	Included in 6.1
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	0	Included in 6.1
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	0	Included in 6.1
6.1.4.1 (e3min=0.75e)	-	0	Included in 6.1
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	0	Included in 6.1
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	0	Included in 6.1
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	0	Included in 6.1
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	0	Included in 6.1
7.1(Appearance:- )	-	300	0
7.2(Colour )	-	300	0
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1100	0
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	700	700+300
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1100	1100+300
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1100	1100+300
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	850	0
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	11000	0
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	850	0
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	0
'7.5 (amdt.7)(Effect on Water (Type test))	-	3000	0

Complete

31 Dec, 2024

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

8288 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
4.0 (chem)(MATERIAL)	-	1050
4.2(Design, Shape & Dimension )	-	300
4.3(Workmanship, Finish & Appearance)	-	300
Cl. 4.4 (a)(Capacity)	-	250
Cl. 4.5(Cl. 4.5 Wall Thickness (Top))	-	250
Cl. 4.5(Cl. 4.5 Wall Thickness (Middle))	-	0
Cl. 4.5(Cl. 4.5 Wall Thickness (Bottom))	-	0
4.6.2(TRANSPARANCY)	-	700
4.6.2.1, Annex-A(Transparency of container)	-	0
Cl. 4.6.3( Cl. 4.6.3 Closure Leakage)	-	1000
Cl. 4.6.3(Cl. 4.6.3 Vibration Leakage)	-	0
Cl. 4.6.3(Cl. 4.6.3 Air Pressure Leakage)	-	0
4.6.4(DROP TEST)	-	1100
4.6.5 , IS:9845:1998 (chem)(Migration- a. Amount of extractive)	-	1700
4.6.5 , IS:9845:1998 (chem)(Migration- b. Amount of extractive)	-	0
4.6.5.1 (chem)(Colour migration (Caps))	-	0
4.6.6 (chem)(Water Potability test (after 30 days) (a) Taste (b) Odour)	-	2900

Complete

31 Dec, 2024

IS 3087 (2005)

Practicle boards of wood and other lingnocellulosic materials (medium density) for general purposes -Specification

20438 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Finish)	-	300	0
8.3(Dimensional Tolerances)	-	500	0
9.2, 11.4(Moisture content)	-	700	700+500
11.10(screw withdrawal strength)	-	1100	1100+500
1 (i) Table 1(Density Variation (Flat Pressed Single Layer))	-	500	0
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 1))	-	500	0
1 (i) Table 1(Density Variation (Flat Pressed Three Layer grade 2))	-	500	0
1 (i) Table 1(Density Variation (Extrusion Pressed Solids) XPS)	-	500	0
1 (i) Table 1(Density Variation (Extrusion Pressed Tubular) XPS)	-	500	0
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Single Layer))	-	550	550+500
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 1))	-	550	550+500
1 (ii) (a) Table 1(Water absorption, 2h soacking (Flat Pressed Three Layer grade 2))	-	550	550+500
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Solids) XPS)	-	550	550+500
1 (ii) (a) Table 1(Water absorption, 2h soacking (Extrusion Pressed Tubular) XPS)	-	550	550+500
1 (ii) Table 1 (b)(Water absorption, 24h soacking (Flat Pressed Single Layer))	-	550	550+500
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Flat Pressed Three Layer grade 2))	-	550	550+500
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Solids) XPS)	-	550	550+500
1 (ii) (b) Table 1 (Water absorption, 24h soacking (Extrusion Pressed Tubular) XPS)	-	550	550+500
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Single Layer))	-	550	0
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 1))	-	550	0
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Flat Pressed Three Layer grade 2))	-	550	0
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Solids) XPS)	-	550	0
1 (iii) (a) Table 1(Linear expression (swelling in water), Length (Extrusion Pressed Tubular) XPS)	-	550	0
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Single Layer))	-	550	0
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Flat Pressed Three Layer grade 2))	-	550	0
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Solids) XPS)	-	550	0
1 (iii) (b) Table 1(Linear expression (swelling in water), Width (Extrusion Pressed Tubular) XPS)	-	550	0
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Single Layer))	-	550	0
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 1))	-	550	0
1 (iv) Table 1(Thickness swelling, Width (Flat Pressed Three Layer grade 2))	-	550	0
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Solids) XPS)	-	550	0
1 (iv) Table 1(Thickness swelling, Width (Extrusion Pressed Tubular) XPS)	-	550	0
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Single Layer))	-	550	0
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 1))	-	550	0
1 (v) Table 1(Swelling in thickness due to surface absorption, (Flat Pressed Three Layer grade 2))	-	550	0
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Solids) XPS)	-	550	0
1 (v) Table 1(Swelling in thickness due to surface absorption, (Extrusion Pressed Tubular) XPS)	-	550	0
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Single Layer))	-	1100	1100+500
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 1))	-	1100	1100+500
1 (vi) (a), Table 1(Modulus of rupture, Average (Flat Pressed Three Layer grade 2))	-	1100	1100+500
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Solids) XPS)	-	1100	1100+500
1 (vi) (a), Table 1(Modulus of rupture, Average (Extrusion Pressed Tubular) XPS)	-	1100	1100+500
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Single Layer))	-	1100	1100+500
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Three Layer grade 1))	-	1100	1100+500
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Flat Pressed Three Layer grade 2))	-	1100	1100+500
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Extrusion Pressed Solids) XPS)	-	1100	1100+500
1 (vi) (b), Table 1(Modulus of rupture, Minimum (Extrusion Pressed Tubular) XPT)	-	1100	1100+500
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Single Layer))	-	1100	1100+500
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 1))	-	1100	1100+500
1 (vii) (a), Table 1(Modulus of elasticity, Average (Flat Pressed Three Layer grade 2))	-	1100	1100+500
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Solids) XPS)	-	1100	1100+500
1 (vii) (a), Table 1(Modulus of elasticity, Average (Extrusion Pressed Tubular) XPT)	-	1100	1100+500
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Single Layer))	-	1100	1100+500
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Three Layer grade 1))	-	1100	1100+500
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Flat Pressed Three Layer grade 2))	-	1100	1100+500
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Extrusion Pressed Solids) XPS)	-	1100	1100+500
1 (vii) (b), Table 1(Modulus of elasticity, Minimum (Extrusion Pressed Tubular) XPT)	-	1100	1100+500
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Single Layer))	-	1100	1100+500
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface,Upto 20mm thickness (Flat Pressed Three Layer grade 1))	-	1100	1100+500
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Flat Pressed Three Layer grade 2))	-	1100	1100+500
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Solids) XPS)	-	1100	1100+500
1 (viii) (a), Table 1(Tensile strenath perpendicullr to surface, Upto 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1100	1100+500
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Single Layer))	-	1100	1100+500
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface,Above 20mm thickness (Flat Pressed Three Layer grade 1))	-	1100	1100+500
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Flat Pressed Three Layer grade 2))	-	1100	1100+500
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Solids) XPS)	-	1100	1100+500
1 (viii) (b), Table 1(Tensile strenath perpendicullr to surface, Above 20mm thickness (Extrusion Pressed Tubular) XPT)	-	1100	1100+500

Complete

31 Dec, 2024

IS 15609 (2005)

Polyethylene flexible pouches for the packing of natural mineral water and packaged drinking water - Specification

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Material)	-	1050	0
6.1.1(Description)	-	500	6.1.1, 6.1.2, 6.1.3, 6.1.4
6.1.2(Film Form)	-	0	Included in 6.1.1
6.1.3(Winding of the Film )	-	0	Included in 6.1.1
6.1.4(Odour)	-	0	Included in 6.1.1
6.1.5 A-2 of IS: 2508:2016(Thickness)	-	250	0
6.1.6(Width)	-	250	0
6.1.7 IS: 9845:1998(Migration- a. Amount of extractive )	-	1700	0
6.1.7 IS: 9845:1998(Migration- b. Colour migration)	-	0	0
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength a. Lengthwise direction)	-	1100	0
6.1.8 Annex 4 of IS:2508:2016(Tensile Strength b. Crosswise direction)	-	1100	0
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - a. Lengthwise direction)	-	0	Included in 6.1.8
6.1.9 Annex 4 of IS:2508:2016(Elongation at break - b. Crosswise direction)	-	0	Included in 6.1.8
6.1.10 Annex -6 of IS:2508:2016(Dart impact Resistance)	-	850	0
Cl. 7.1(Vibration Leakage Test)	-	1000	0
7.2(Water potability)	-	2900	0
7.3(Stack load test)	-	900	0
7.4(Drop test)	-	1100	0
7.5(Ink adhesion test)	-	500	0
7.6(Product resistance test)	-	500	0

Complete

31 Dec, 2024

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

12100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	925
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700
6.2.2(Fittings)	-	0
6.3(General)	-	300
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000
8.3.1(Wall Thickness ofEmitting Pipe)	-	250
8.3.2(Inside Diameter ofEmitting Pipe)	-	0
8.3.3(Flow Paths in Emitting Unit)	-	400
8.3.4(Spacing ofEmitter Units)	-	0
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1600
8.5(Resistance to Tension at Elevated Temperature)	-	1100
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	400
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1200
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1600
8.8(Determination of Emitting Unit Exponent)	-	600

Complete

31 Dec, 2024

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

111344 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Dimensions Of Pipes)	-	250	0
Cl 8(Visual Appearance)	-	300	0
Cl 9.1(Hydraulic Characteristics)	-	18400	1000+1600+4800+11000
Cl 9.2(Fusion Compatibility)	-	4800	0
Cl 9.3(Reversion Test )	-	700	700+300
Cl 9.4 & Annex B(Impact Strength)	-	1100	1100+300
Cl 9.5(Density)	-	500	0
Cl 9.6(Melt Flow Rate)	-	1100	0
Cl 9.7(Carbon Black Content & Dispersion)	-	1625	925+700
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	1700	1700+82125
Cl 9.9(Opacity)	-	575	0

Complete

31 Dec, 2024

IS 15907 (2010)

Agro textiles – High density polyethylene (HDPE) woven beds for vermiculture – Specification

62910 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Identification)	-	2000	0
4.1(Linear Density)	-	250	0
4.1(Width)	-	250	0
4.3(Cord Beading - IS 15907)	-	250	0
5.2.1(Lamination- IS 15907)	-	250	0
5.2.1(Thickness of coating film- method A of IS 13162 (Part 3))	-	250	0
5.2.1(Lamination- IS 15907)	-	2000	0
5.3.1(Construction- IS 15907)	-	300	0
5.3.1(The width of the hem - IS 15907)	-	250	0
5.3.2(Finished width of pocket - IS 15907)	-	250	0
5.3.2(Construction- IS 15907)	-	250	0
5.3.2(Construction- IS 15907)	-	350	0
6- Table 1- SL.No (i)(Mass)	-	250	0
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,warp - IS 1969 )	-	1100	1100+250
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,weft - IS 1969 )	-	1100	0
6- Table 1- SL.No (iv)(Retention of breaking strength after UV exposure, - Annex B of IS 15907 and IS 1969)	-	1100	1100+250
6- Table 1- SL.No (v)(Welded seam strength before UV exposure- IS 1969)	-	1100	1100+250
6- Table 1- SL.No (vi)(Welded seam strength after UV exposure- Annex B of IS 15907 and IS 1969)	-	1100	0
6- Table 1- SL.No (vii)(Tear strength, Warp - Method A2 of IS 7016 (Part 3))	-	1100	1100+250
6- Table 1- SL.No (vii)(Tear strength, Weft - Method A2 of IS 7016 (Part 3))	-	1100	0
6- Table 1- SL.No (viii)(Puncture strength - Annex C of IS 15907)	-	1100	0
6- Table 1- SL.No (ix)(Environmental stress cracking test - Annex D of IS 15907)	-	1200	1200+250
6- Table 1- SL.No (x)(Resistance to chemicals, change in the mass - Annex E of IS 15907)	-	2000	2000+250
6- Table 1- SL.No (xi)(Colour fastness to artificial light -IS 2454)	-	1500	1500+250
6- Table 1- SL.No (xii)(Bursting pressure-IS 1966)	-	1100	1100+250
6.1(Length -IS 15907)	-	250	0
6.1(Width - IS 15907)	-	250	0
6.1(Height - IS 15907)	-	250	0
6.2(Water Proofness, IS 7940)	-	1000	0
6.2(Water Proofness,IS 7941)	-	1000	0

Complete

31 Dec, 2024

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

37600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	300	0
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100	K Value
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	0
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Included in 7.1
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Included in 7.1
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0	Included in 7.1
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	Included in 7.1
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	Included in 7.1
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	300	0
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	700	700+300
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	0
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	0
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	0
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	2000+300
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1100	1100+300
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1100	1100+250
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	700	0
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	0
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	1000	0

Complete

31 Dec, 2024

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

23143 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
3.1(Material Identification)	-	1050
3.1(Overall Migration)	-	1700
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500
3.3.1(Bottom seam (IS 10789))	-	300
4.2 and Table 1 ii(Dimensions )	-	250
5.2 and Table 1 iii(Ends per dm )	-	250
5.2 and Table 1 iv(Picks per dm )	-	0
4.2 and Table 1 v(Mass of sack )	-	300
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100
4.2 and Table 1 viii(Elongation at break of fabric )	-	0
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200
4.2 and Table 1 x(Ash content )	-	950
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	1100
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1400

Complete

31 Dec, 2024

IS 12823 (2015)

Prelaminated Particle Boards from Wood and other Lignocellulosic Material - Specification ( First Revision )

18281 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Dimensions & Tolerances)	-	1000	0
Cl 10.2(Test For Density)	-	500	0
Cl 10.3(Test For Moisture Content)	-	700	700+500
Cl 10.4(For Water AbsorptionTest )	-	1200	1200+500
Cl 10.5(For Swelling in water Test )	-	300	0
Cl 10.6(Tesr For Modulus Of Elasticity & Mudulus Of Rupture)	-	1100	0
Cl 10.7(For Determination of Tensile Strength Perpendicular to Surface)	-	1100	1100+500
Cl 10.8(For Determination of Tensile Strength Perpendicular to Surface After Ageing Test)	-	1100	1100+4300
Cl 10.9(Test For Screw Withdrawal Strength)	-	2200	2200+500
Cl 10.10 & Annex C( Test For Abrasion Resistance)	-	875	0
Cl 10.11 & Annex D( Test For Resistance to Steam)	-	900	0
Cl 10.12 & Annex E( Test For Crack Resistance)	-	900	0
Cl 10.13 & Annex F( Test For Resistance to Cigarette Burn)	-	900	0
Cl 10.14 & Annex G( Test For Resistance to Stain)	-	1000	0

Complete

31 Dec, 2024

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

26843 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
4.1(Raw Material)	-	2000
4.2(Tapes – Width IS 6192 and IS 11197)	-	250
4.2(Tapes – Linear Density )	-	500
4.3.1(Bottom Seam)	-	300
4.3.1(The two rows of stitches shall be separated from each other)	-	250
4.3.1( The outer stitch)	-	250
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	250
4.3.1(stitches/dm)	-	250
4.3.2(Mouth)	-	250
4.4(Liner IS 10146 or IS 10910.)	-	2000
4.4(Mass of the loose liner )	-	250
4.4(Width of the loose liner)	-	250
4.4(Length of the line)	-	250
4.4(Bottom seam of the loose liner)	-	300
4.4.1(Liner)	-	300
4.5 and Table 1 i(Capacity)	-	250
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250
5.2 and Table 1 iii(Ends per dm )	-	250
5.2 and Table 1 iv(Picks per dm )	-	0
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	250
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	1100
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	1100
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1100
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1100
5.2 and Table 1 x(Ash content )	-	950

Complete

31 Dec, 2024

IS 15351 (2015)

Agro textiles – Laminated high density polyethylene (HDPE) woven geomembrane for water proof lining – Specification (second revision)

194612 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
5.3(Joints/Seams)	-	250
5.1.1 and 6.2(Thickness, mm- IS 7016: Part 1)	-	250
5.1.1 and 6.2(Mass, g/sq m)	-	250
5.1.1 and 6.2(Length)	-	250
5.1.1 and 6.2(Width)	-	250
5.1.1 and 6.2(Carbon black content, Percent- IS 2530)	-	925
5.1.1 and 6.2(Breaking Load on 20 cm X 10 cm Strip, Min )	-	1100
5.1.1 and 6.2(Strain at Maximum load, Percent-IS 13162 (Part 5)	-	1100
Table-1(Breaking load on 20 × 10 cm strip, N, Min after)	-	1100
5.1.1 and 6.2(Impact failure load, at 1524 mm drop,)	-	1100
5.1.1 and 6.2(Tear resistance, N, Min-Method A1 of IS 7016 (Part 3))	-	1100
5.1.1 and 6.2(Puncture resistance, N, Min-Annex D)	-	1100
5.1.1 and 6.2(Bursting strength (Ball burst),N/cm², Min-)	-	1000
5.1.1 and 6.2(Seam strength before UV exposure (N/mm), Min-IS 15060)	-	1100
Table-1(Seam strength after UV exposure N/mm, Min-Annex B and IS 15060)	-	1100
5.1.1 and 6.2(Hydrostatic resistance-Annex E)	-	1000
5.1.1 and 6.2(Ash content, percent, Max-Annex F)	-	950
Table-1(Hydrostatic resistance after UV exposure of 1000 h -Annex B and Annex E)	-	1000

Complete

31 Dec, 2024

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

23967 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	0
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	0
4.2(Tapes – Linear Density )	-	0	0
4.3(Sacks)	-	300	4.3, 4.3.1 & 4.3.2
4.3.1(Bottom Seam)	-	0	Included in 4.3
4.3.1( The two rows of stitches shall be separated from each other)	-	0	Included in 4.3
4.3.1( The outer stitch)	-	0	Included in 4.3
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	Included in 4.3
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	Included in 4.3
4.3.1(The number of stitches/dm)	-	0	Included in 4.3
4.3.2(Mouth)	-	0	Included in 4.3
4.4 and Table 1 i(Capacity)	-	250	Clause 5.2
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	0
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	0
5.2 and Table 1 iii(Ends per dm )	-	250	0
5.2 and Table 1 iv(Picks per dm )	-	250	0
5.1 and Table 1 v(Mass of sack )	-	250	0
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	0
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	0
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	0
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	0
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	0
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1100	1100
5.2 and Table 1 x(Ash content )	-	950	0
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1100	0

Complete

31 Dec, 2024

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

16537 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	300	0
5.1.2(Film Form)	-	0	0
5.1.3(Odour)	-	0	0
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	500	0
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	0
5.1.6a(Carbon Black Content, Annex-A)	-	925	0
5.1.6b(Ash Content, Annex-A)	-	950	0
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	0
5.2.2(Tolerance on Thickness, Annex-A)	-	600	0
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1100	1100+250
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1100	0
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4300	0
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	1100	1100+250
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	1100	0
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1000	0
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	750	750+250
6.1, Table 1(Tear resistence. B) Transverse direction )	-	750	0
8.1, Table 3(Puncture resistance , Annex C)	-	1100	0

Complete

31 Dec, 2024

IS 9755 (2016)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing fertilizers – Specification (fifth revision)

23193 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MANUFACTURE-Raw Material)	-	1050	0
3.2(MANUFACTURE-)	-	250	0
3.3(Sacks)	-	300	0
3.4(Liner)	-	1050	0
3.4.1(Liner)	-	300	0
3.7(Mouth of the Sack)	-	250	0
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	250	0
3.4(Liner-The thickness(A-2 of IS 2508) shall be 40 μm ± 10 percent in case of HMHDPE/ HDPE.)	-	200	0
3.4(Liner-The thickness(A-2 of IS 2508) shall be 70 μm ± 10 percent in case of LDPE/LLDPE)	-	200	0
4.2(UV Resistance-The HDPE/PP woven fabric of sack made out of UV stabilized material shall have at least 50 percent of the original breaking strength when tested after the same has been exposed to UV radiation and weathering as per the method given in Annex D.)	-	2200	1100+1100
4.3(Mass-(Annexure E))	-	250	0

Complete

31 Dec, 2024

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

56576 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
3.2(HDPE Fabric (Material Identification))	-	1050
3.3(Eyelets)	-	250
3.4( Line/ Cord beading IS 7903)	-	250
5.3(Joint/Seam, IS 7903)	-	250
5.4(Fixing of Eyelets, IS 7903)	-	250
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	500
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	1100
6.1 Table 1vi)(Breaking strength before UV exposure,weft, IS 1969 part 1)	-	1100
6.1 Table 1 vii)(Elongation at break of fabric,warp, IS 1969 Part 1)	-	0
6.1 Table 1 vii)(Elongation at break of fabric,weft, IS 1969 Part1)	-	0
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Warp, IS 13162 part 2& IS 1969 Part1 )	-	1100
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Weft , IS 13162 part 2& IS 1969 Part1 )	-	1100
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	1100
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	1100
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	1100
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	1100
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	1100
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	850
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	950
6.2(Length, IS 7903)	-	500
6.2(Width, IS 7903)	-	0
6.2(height, IS 7903)	-	0
6.3(Water Proofness,IS 7941)	-	2000
6.3(Water Proofness, IS 7940)	-	2000
6.3(Water Proofness,IS 7941)	-	0
6.3(Water Proofness, IS 7940)	-	0
5.2.1(Construction IS 7903)	-	250

Complete

31 Dec, 2024

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

21543 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	250
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	250
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	250
4.1(Raw Material )	-	1050
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0

Complete

31 Dec, 2024

IS 3462 (1986)

Unbacked Flexible Pvc Flooring

17238 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(DIMENSIONS AND TOLERANCES-Thickness)	-	200	0
5.1.1(DIMENSIONS AND TOLERANCES-Liaear Dimension-Sheets or Rolls)	-	250	0
7.1-Table 1(iv)(REQUlREMENTS-Dimensional stability )	-	700	0
7.1-Table 1(v)(REQUlREMENTS-Colour fastness to daylight )	-	850	0
7.1-Table 1(xi)(REQUlREMENTS-Ply adhesion )	-	1100	1100+300
7.1-Table 1(xii)(REQUlREMENTS-Moisture movernent )	-	700	0
7.1-Table 1(x)(REQUlREMENTS-Resistance to various substances )	-	1100	0
7.1-Table 1(xiii)(REQUlREMENTS-Heat ageing and exudation )	-	1100	1100+9000
7.1-Table 1(xiii)(REQUlREMENTS-Elastic product)	-	1100	1100+250
6. 1(COLOUR AND SURFACE CHARACTERISTICS)	-	250	0

Complete

31 Dec, 2024

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
Cl.4(Minimum Thickness)	-	500
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0
Cl. 6.1(Stress Relief Test- Appendix A)	-	700
Cl. 6.2(Opacity- Appendix B)	-	575
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	3000
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	850

Complete

31 Dec, 2024

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
cl 2.2.2(Dimensions)	-	500
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	3000
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	0
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	0

Complete

31 Dec, 2024

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)
2.2.3(Socket length)	-	500
2.2.3( inside diameter of the socket)	-	0
2.2.2, Table 1(Socket Laying Length)	-	0

Complete

31 Dec, 2024

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

7294 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1(General)	-	500		0
2.2.2(diameter of the socket of cap)	-	0		0

Complete

31 Dec, 2024

Bureau of Indian Standards

The National Standards Body of India

CIPET, Ahmedabad

Plot No. 630, Phase-IV, GIDC, Vatva,, Ahmedabad, Ahmadabad, Gujarat, 382445

7229000205 cipetahmd@gmail.com

Scope List