BIS - LIMS (Laboratory Information Management System)

SHRI KRISHNA TEST HOUSE PVT LTD (142)

Plot No.142, Sec-G, Bawana-II, DSIIDC, Bhorgarh industrial area New Delhi, Delhi, North, Delhi, 110040

9266808773 SKTHPL142@GMAIL.COM

Scope List

Reset

68 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 5082 (1998)

Wrought aluminium and aluminium alloy bars, rods, tubes, sections, plates and sheets for electrical applications (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(CHEMICAL COMPOSITION Table 1)	-	15000	-
Clause 5(FREEDOM FROM DEFECTS)	-	15000	-
8.1(MECHANICAL TEST Tensile Strength Min, Mpa)	-	15000	-
8.1(MECHANICAL TEST (0.2 Percent Proof Stress Min, Mpa))	-	15000	-
8.1(Percent Elongation on 5.65 Min)	-	15000	-
8.1(Electrical Conductivity at 20°C,Min)	-	15000	-
8.1(Maximum Electrical Resistivity at 20°C ohm-mm/mm2)	-	15000	-
8.2(Bend Test)	-	15000	-
Clause 10(DIMENSIONAL TOLERANCES)	-	15000	-
6.1, Table 1(Aluminium)	-	15000	-
6.1, Table 1(Copper)	-	15000	-
6.1, Table 1(Magnesium)	-	15000	-
6.1, Table 1(Silicon)	-	15000	-
6.1, Table 1(Manganese)	-	15000	-
6.1, Table 1(Zinc)	-	15000	-
6.1, Table 1(Titanium)	-	15000	-
6.1, Table 1(Chromium)	-	15000	-
6.1, Table 1(Iron)	-	15000	-
6.1, Table 1(Vanadium)	-	15000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 17150 (2019)

Mini domestic water heater for use with piped natural gas (PNG) ? specification

ALL

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
26(Hot water output, Declared Value)	-	30000	-
25(When tested as per annex D, at the nominal gas rate with the appliance adjusted to give a temperature rise of 45±5°C between the water inlet and outlet , the time to achieve 90% of this temperature rise-)	-	30000	-
24(Temperature of synthetic rubber diaphragm in gas carrying components)	-	30000	-
24(Temperature of the surface in normal use)	-	30000	-
24(Surface temperature:Temperature of the portion of the surface other than the working surface likely to be touched accidentally.)	-	30000	-
24(Wall, Floor, Ceiling temperatures: Rise of Temperature above room temperature in , after two hours of operation)	-	30000	-
23(There shall be no extinction of flame on any of the burner operating at the maximum consumption when the appliance is placed in a normal current of air with velocity of 2 m/s as measured with a rotating vane anemometer. The location of the appliance relative to the neighbouring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation, applicable for all pressure 20-25 gf/cm².)	-	30000	-
22(While the appliance is in operation at full gas consumption and the appliance is in thermal equilibrium, the flame shall be immediately reduced to the minimum possible and then brought back to the full size, the operation shall be repeated five times, no flash back shall occur during the test, applicable for pressure 20-25 gf/cm².)	-	30000	-
21(Ignition of Burner flame, their operation and turning off shall not give rise to undue excessive noise during the operation.)	-	30000	-
20(Pilot Flame shall be Stable without lifting or soot deposition at gas inlet pressure from 20-25 gf/cm2)	-	30000	-
20(It shall be possible to operate the appliance with taps fully open at gas inlet pressure , without the flame extinguishing, blowing off or striking back and without the formation of soot.)	-	30000	-
19.3(if the burner is ignited from a pilot flame , ignition shall be smooth at pressure from 20-25 gf/cm² with the tap turned full on and ignition shall be effected without delay after turning on the taps.)	-	30000	-
19.2(if the flame is applied to any one burner pors when the gas is flowing , flame travel shall be complete. This applies for all pressures from 20 to 25 gf/cm² taps being fully open.)	-	30000	-
19.1(Where the burner or burners are lighted by automatic ignition , it shall not be possible for gas to be admitted to the main burner without igniters being on.)	-	30000	-
19.1(There shall be easy and safe access of lighting each burner by matchstick and it shall be easy to see that the burner is lighted)	-	30000	-
18( (D = Declared Value, Gas Consumption)	-	30000	-
17(Ratio of Carbon Monoxide to Carbon Dioxide)	-	30000	-
16(Thermal efficiency of Water Heater shall not be less nthan 62%)	-	30000	-
15(The later circuit shall be kept under pressure for minimum 5 min.)	-	30000	-
15(All water carrying parts of the appliance, individually and when assembled to form the water circuit of the appliance shall not leak or show any permanent distortion during or after the test when tested at a hydrostatic pressure 4 kgf/cm2)	-	30000	-
14(All gas carrying parts of the appliances should be sound and these parts when connected to form complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m²)	-	30000	-
12(The Appliance shall be provided with a means of adjusting water rate.)	-	30000	-
11(The gas supply shall be restored manually.)	-	30000	-
11(The Water heater shall be provided with a suitable overheat protection device, which shall switch off the supply of gas, if the temperature of the delivered water reaches 80°C max. )	-	30000	-
10(The ignition to the burners from pilot shall be smooth)	-	30000	-
10(It is essential that the pilot flame shall be seen either directly or by reflection.)	-	30000	-
10(The pilot burner shall be made of a material that shall not deteriorate under normal condition of use)	-	30000	-
10(While in operation the relative position of the pilot and burner shall not alter.)	-	30000	-
10(The pilot shall be positioned in such a way that their products of combustion are evacuated with those of the burner)	-	30000	-
10(An appliance shall have an ignition device, where the appliance is provided in the form of a pilot it shall be possible to light it easily with a matchstick or a special ignition device)	-	30000	-
9.1(The Appliance shall have a flame failure device, controlling the admission of gas to the main burner and possibly to any ignition pilot. The provisions given in 14.1 of IS:5116 shall apply.)	-	30000	-
8(The device shall be of such a design that gas shall not enter to the main burner and the pilot (if provided) until it is reset to the original position.)	-	30000	-
8(The Appliance shall have a device allowing manual interruption of the supply of gas to the burner and pilot, if available in case of exigency.)	-	30000	-
7(All Appliances shall be designed so that ignition, correct burner performance and the length of the pilot flames. If any , can always be easily seen. This visibility shall be assumed at all times and particularly, where there is a viewing window, this shall not deteriorate under the effect of heat.)	-	30000	-
6.6(Gas Inlet Connections : The water heater shall be provided with nozzle or screwed gas inlet connection as given in 18 of IS:5116)	-	30000	-
6.5(The gas and water connections shall be situated at the base of the appliance. it shall be possible to connect the appliance to supply, which are in a plane parallel or perpendicular to the wall on which the appliance is fixed.)	-	30000	-
6.4(The water inlet and outlet connection shall be of 1/2" BSP thread.)	-	30000	-
6.3(All water connection shall be of copper or brass tube and have at least 6 mm inner diameter and 0.5 mm nominal wall thickness of the tube.)	-	30000	-
6.2(Gas inlet connection shall permit a rigid connection.)	-	30000	-
6.2(Gas inlet connection shall permit a rigid connection.)	-	30000	-
6.1(For connections and screws other than for water, metric threads shall be used. )	-	30000	-
5.5(Diaphragm if provided for inlet water control device, shall be made of synthetic rubber.while choosing the material, the manufacturer shall take into account the characteristics required for the satisfactory use that is , mechanical and chemical stability. Material selected shall not degrade under normal working conditions.)	-	30000	-
5.4(Melting point of metal for burner top)	-	30000	-
5.4(The main body of the burner including mixer head, mixing tube and burner head shall be of substantial and durable construction)	-	30000	-
5.3(Change in weight or volume of a non metallic material, when immerse in n-Pentane for 72 hours)	-	30000	-
5.2(The copper and copper alloy forged and cast parts shall pass the mercurous nitrate test (Season cracking test) when tested according to the method specified in IS:2305.)	-	30000	-
5.1(The material used in the construction of the water heater shall be resistant to wear and deterioration occuring in the normal use.)	-	30000	-
4.1.12(All heat exchanger tubes through which the water passes and water chamber, if provided, shall be completely filled with water before igniting the burner.)	-	30000	-
4.1.11(The water heater shall have a provision such that supply of gas shall be cut off and the burner extinguished after 20+1/-2 min of uninterrupted use. The appliance shall able to restart manually.)	-	30000	-
4.1.10(The Appliance shall be provided with a safety device, which cuts off the supply of gas in case water dose not flow or stops flowing while in operation.)	-	30000	-
4.1.9(The gas (heat) input to the pilot alone shall not exceed 8 l/h at a gas inlet pressure of 21 mbar and at temperature 25-30°C, wherever applicable.)	-	30000	-
4.1.8(Interior surfaces shall be of such material or so protected, so as to avoid contamination of the contents.)	-	30000	-
4.1.8(All parts of gas water heaters subject to direct heat shall have brazed or welded joints.)	-	30000	-
4.1.7(it shall be possible to install an appliance intended to be fixed to a wall with appropriate means of fixing, such as clamps, hooks, Screws, etc. )	-	30000	-
4.1.6(The gas and water soundness shall be assured after reassemble maintenance.)	-	30000	-
4.1.5(It shall not be possible to replace to replace parts, which are removable for maintenance in a way that could impair the safe performance of the appliance.)	-	30000	-
4.1.4(it shall be possible to clean without difficulty)	-	30000	-
4.1.3(All Parts shall be made and so assembled that the performance characteristics of the appliance will not alter significantly during reasonable life and in normal conditions of installation and use.)	-	30000	-
4.1.2(All parts in contact with water shall be made of such a material that shall not pollute water.)	-	30000	-
4.1.1(No PNG regulator shall be included as a part of the instantaneous domestic gas water heater.)	-	30000	-
4.1(Rivets, Fastening screws and plugs , etc. shall not lead into gas passages.)	-	30000	-
4.1(The construction of all the parts of equipment shall be sound and of high standard of workmanship and appropriate finish. The construction shall ensure durability and shall comply with the safety requirements.)	-	30000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 2553 : Part 1 (2018)

Safety glass - Specification: Part 1 architectural, building and general uses (Fourth Revision)

ALL

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Types)	-	20000	-
5.1.1(General)	-	20000	-
5.1.2(Optical Faults-IS 14900)	-	20000	-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	20000	-
5.1.2(Reams, Strings and Lines-IS 14900)	-	20000	-
5.1.2(Linear / Extended Faults -IS 14900)	-	20000	-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	20000	-
5.2.2.1( Dimensions- Width )	-	20000	-
5.2.2.1( Dimensions- Length)	-	20000	-
5.2.2.2( Squareness)	-	20000	-
5.2.3 (Fragmentation Test- IS 17004)	-	20000	-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	20000	-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	20000	-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	20000	-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	20000	-
5.2.4.1 (Other distortions)	-	20000	-
5.2.5.1( Resistance to shock- IS 17004)	-	20000	-
5.2.5.2( Resistance to human impact- IS 17004)	-	20000	-
5.2.6( Surface Compression (Optional)- IS 17004)	-	20000	-
5.2.7( Mechanical Strength — Four Point Bending Test (Optional)- IS 17004)	-	20000	-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	20000	-
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	20000	-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	20000	-
5.3.2.1( Dimensions and squareness- Width )	-	20000	-
5.3.2.1( Dimensions and squareness- Length)	-	20000	-
5.3.2.1( Dimensions and squareness-Squareness)	-	20000	-
5.3.2.2 (Edge displacement)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.4( Boil and Bake Tests-IS 17004)	-	20000	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	20000	-
5.3.6.1( Spot defects in the central area)	-	20000	-
5.3.6.2 (Linear defects in the central area)	-	20000	-
5.3.6.3( Defects in the outer area for framed edges)	-	20000	-
5.3.6.4( Vents)	-	20000	-
5.3.6.5( Creases and streaks)	-	20000	-
5.3.6.6( Defects on edge which will not be framed)	-	20000	-
5.3.7( Humidity Test – Optional)	-	20000	-
5.3.8( Resistance to Human Impact Test)	-	20000	-
4(Types)	-	20000	-
5.1.1(General)	-	20000	-
5.1.2(Optical Faults-IS 14900)	-	20000	-
5.1.2(Spot Faults of category A/B/C/D -IS 14900)	-	20000	-
5.1.2(Reams, Strings and Lines-IS 14900)	-	20000	-
5.1.2(Linear / Extended Faults -IS 14900)	-	20000	-
5.2.1 (Thickness -IS 17004 & IS 14900)	-	20000	-
5.2.2.1( Dimensions- Width )	-	20000	-
5.2.2.1( Dimensions- Length)	-	20000	-
5.2.2.2( Squareness)	-	20000	-
5.2.3 (Fragmentation Test- IS 17004)	-	20000	-
5.2.4-a( Flatness-Overall bow-IS 17004)	-	20000	-
5.2.4-b( Flatness-Roller wave distortion-IS 17005)	-	20000	-
5.2.4-c( Flatness-Edge lift-IS 17006)	-	20000	-
5.2.4-d( Flatness-Local distortion-IS 17007)	-	20000	-
5.2.4.1 (Other distortions)	-	20000	-
5.2.5.1( Resistance to shock- IS 17004)	-	20000	-
5.2.5.2( Resistance to human impact- IS 17004)	-	20000	-
5.2.6( Surface Compression (Optional)- IS 17004)	-	20000	-
5.2.7( Mechanical Strength — Four Point Bending Test (Optional)- IS 17004)	-	20000	-
5.2.8.1 & 5.2.8.3-Table 7(Diameter of Holes & Deviations on holes )	-	20000	-
5.2.8.3-Table 8(Deviations on position of holes and Cutouts Location)	-	20000	-
5.3.1 (Thickness-IS 17004 & IS 14900)	-	20000	-
5.3.2.1( Dimensions and squareness- Width )	-	20000	-
5.3.2.1( Dimensions and squareness- Length)	-	20000	-
5.3.2.1( Dimensions and squareness-Squareness)	-	20000	-
5.3.2.2 (Edge displacement)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.3( Light Stability Test-IS 17004)	-	20000	-
5.3.4( Boil and Bake Tests-IS 17004)	-	20000	-
5.3.5( Fracture and Adhesion Test-IS 17004)	-	20000	-
5.3.6.1( Spot defects in the central area)	-	20000	-
5.3.6.2 (Linear defects in the central area)	-	20000	-
5.3.6.3( Defects in the outer area for framed edges)	-	20000	-
5.3.6.4( Vents)	-	20000	-
5.3.6.5( Creases and streaks)	-	20000	-
5.3.6.6( Defects on edge which will not be framed)	-	20000	-
5.3.7( Humidity Test – Optional)	-	20000	-
5.3.8( Resistance to Human Impact Test)	-	20000	-
5.2.1(Thickness)	-	20000	-
5.2.2(Dimension and Squarenes)	-	20000	-
5.2.4(Overall Bow)	-	20000	-
5.2.4(Measurement of wave and roller wave)	-	20000	-
5.2.4(Edge lift)	-	20000	-
5.2.4(Local distortion)	-	20000	-
5.2.3(Fragmentation test)	-	20000	-
5.2.7(Four point bending)	-	20000	-
5.2.6(Surface compression)	-	20000	-
5.2.5.1(Resistance to shock)	-	20000	-
5.2.5.2(Resistance to human impact)	-	20000	-
5.3.1(Thickness test)	-	20000	-
5.3.2.1(Dimension and Squarenes test)	-	20000	-
5.3.6(Defects in central area test)	-	20000	-
5.3.6.7(Defects in central area test)	-	20000	-
5.3.5(Fracture and adhesion)	-	20000	-
5.3.8(Resistance to human impact)	-	20000	-
5.3.4(Boil test)	-	20000	-
5.3.4(Bake test)	-	20000	-
5.3.7(Humidity test with condensation)	-	20000	-
5.3.7(Humidity test without condensation)	-	20000	-
5.3.3(Light stability test)	-	20000	-
5.3.2.2(Edge displacement test)	-	20000	-
5.2.2(5.2.2 Dimension and Squarenes test)	-	20000	-
5.2.4(measurement of wave and roller wave)	-	20000	-
5.2.8(Fabrication in Glass)	-	20000	-
Cl. No. 5.2.2.3.1, Table No. 1A(Shape accuracy, girth and length)	-	20000	-
Cl. No. 5.2.2.3.2(Edge straightness deviation)	-	20000	-
Cl. No. 5.2.2.3.3(Maximum cross-curve deviation)	-	20000	-
As per Clause 5.3.9(Laminated Glass)	-	20000	-
As per Clause 5.2.8.2(Toughened)	-	20000	-
As per Clause 5.2.8.4(Toughened)	-	20000	-
As per Clause 5.2.9(Toughened)	-	20000	-
As per Clause 5.3.6.4(Laminated Glass)	-	20000	-
As per Clause 5.3.6.5(Laminated Glass)	-	20000	-
As per Clause 5.3.6.6(Laminated Glass)	-	20000	-
As per Clause 5.5.2.1(Laminated Glass and Glass-Plastic Panes)	-	20000	-
As per Clause 5.5.3.2(Laminated Glass and Glass-Plastic Panes)	-	20000	-
As per Clause 5.6.2(Rigid Plastic Glazing)	-	20000	-
As per Clause 5.7.1(Flexible Plastic)	-	20000	-
As per Clause 3.7(Wind screen and Panes)	-	20000	-
As per Clause 4.1(Wind screen and Panes)	-	20000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 6912 (2005)

Copper and copper alloys forging stock and forging - Specification (Second Revision)

ALL

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
As per Clause 12.1.1(For Forging Stock)	-	12000	-
As per Clause 12.1.2(For Forging)	-	12000	-
As per Clause 13.1.1(Forging Stock)	-	12000	-
As per Clause 13.1.2(Hot Worked Material)	-	12000	-
As per Clause 13.1.3(Cold Worked Material)	-	12000	-
As per Clause 13.1.4(Cast Material)	-	12000	-
As per Clause 13.1.5(Diameter or Width Across flats greater than 28 mm)	-	12000	-
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
Cl. No.4(SUPPLY OF MATERIAL)	-	12000	-
Cl. No.6(Freedom from defects)	-	12000	-
Cl. No.7, Table no. 1("DIMENSIONS AND TOLERANCES ")	-	12000	-
Cl. No.8.1, Table no.2(i)(Electrolytic tough pitch through copper)	-	12000	-
Cl. No.8.1, Table no.2(ii)(Fire refined high conductivity copper)	-	12000	-
Cl. No.8.1, Table no.2(iii)(Phosporus deoxidised arsenical copper)	-	12000	-
Cl. No.8.1, Table no.3(Chemical Composition and Mechanical Properties of Brasses)	-	12000	-
Cl.no.8.1, Table no. 4(Chemical Composition and Mechanical Properties of Bronzes)	-	12000	-
Cl.no.9(Mechanical properties)	-	12000	-
Cl.no.10(Forgability Test)	-	12000	-
Cl. No. 11(Mercurous Nitrate Test (For Forgings))	-	12000	-
Cl. No.15(Marking)	-	12000	-
As per Clause 12.1.1(For Forging Stock)	-	12000	-
As per Clause 12.1.2(For Forging)	-	12000	-
As per Clause 13.1.1(Forging Stock)	-	12000	-
As per Clause 13.1.2(Hot Worked Material)	-	12000	-
As per Clause 13.1.3(Cold Worked Material)	-	12000	-
As per Clause 13.1.4(Cast Material)	-	12000	-
As per Clause 13.1.5(Diameter or Width Across flats greater than 28 mm)	-	12000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 1264 (1997)

Brass gravity die castings - Specification (Fourth Revision)

All

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	8000	-
6.0(Shape)	-	8000	-
6.0(Size)	-	8000	-
6.0(Mass)	-	8000	-
7.0(Cu)	-	8000	-
7.0(Sn)	-	8000	-
7.0(Pb)	-	8000	-
7.0(Ni)	-	8000	-
7.0(Fe)	-	8000	-
7.0(Al)	-	8000	-
7.0(Mn)	-	8000	-
7.0(Si)	-	8000	-
7.0(Total impurities excluding Ni Pb Al Zn)	-	8000	-
9.0(Pressure test)	-	8000	-
11(Marking)	-	8000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 17153 (2019)

Domestic gas stoves for use with piped natural gas (PNG) - Specification

all

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
26(Burner-5)	-	42000	Single Burner SS Body – Rs.20000/- Glass Top – Rs. 23000/- Double Burner SS Body – Rs. 25000/- Glass Top – Rs. 28000/- Three Burner SS Body – Rs. 30000/- Glass Top – Rs. 33000/- Four Burner SS Body – Rs. 35000/- Glass Top – Rs. 38000/- Five Burner SS Body
26(Burner-4)	-	42000	-
26(Burner-3)	-	42000	-
26(Burner-2)	-	42000	-
26(Burner-1)	-	42000	-
25.2(With the Burner lighted on full on, the flame temperature at a height of H+20 mm)	-	42000	-
25.1(Temperature of synthetic rubber diaphragm in gas carrying components)	-	42000	-
25.1(Temperature of the surface in normal use)	-	42000	-
25.1(Temperature of the portion of the surface other than the working surface likely to be touched accidentally.)	-	42000	-
25.1(Rise of Temperature above room temperature in (Wall, Floor, Ceiling), after two hours of operation)	-	42000	-
24(Burner-5)	-	42000	-
24(Burner-4)	-	42000	-
24(Burner-3)	-	42000	-
24(Burner-2)	-	42000	-
24(Burner-1)	-	42000	-
23(When operated at pressure 20-25 gf/cm2 , there shall be no extinction of flame on any of the burneroperating at the max of the burner, when the appliance is placed in normal current of air with velocity of 2 m/s.)	-	42000	-
22(When operated at pressure 20-25 gf/cm2 , for one at full on position, no soot shall be deposited on burner or on the bottom of the vessel.)	-	42000	-
21(When operated at pressure 20-25 gf/cm2 for half an hour flame shall be reduced to simmer and then brought back to full on, operation shall be repeated five times, no flash back shall occur during the test.)	-	42000	-
20(Ignition of Burner flame, their operation and turning off shall not give rise to undue excessive noise during the operation.)	-	42000	-
19.3(Fixed Min Pilot flame shall be sufficient to relight the main burner at the 21 mbar gas inlet pressure.)	-	42000	-
19.2(Pilot Flame shall be Stable without lifting or soot deposition at gas inlet pressure from 20-25 gf/cm2)	-	42000	-
19.1.1(When the gas consumption of the burner is reduced to simmer after operating half an hour on full ON flame shall not extinguish, blow off, strike back or form soot at 21 mbar gas inlet pressure.)	-	42000	-
19.1(It shall be possible to operate stove with taps fully open at gas inlet pressure , without the flame extinguishing, blowing off or striking back and without the formation of soot.)	-	42000	-
18.4.1(The flame failure device if provided shall confirm to IS:5116)	-	42000	-
18.3(When the burner is ignited from a pilot flame and/or by an electric/electronic method, the ignition and flame travel shall be smooth at pressure……..)	-	42000	-
18.2(if the flame is applied to any of the outer row of the burner ports when the gas is flowing , flame travel shall be complete……..)	-	42000	-
18.1(Where the burner or burners are lighted by automatic ignition (Battery of flint operated or by a pilot flame , it shall not be possible for gas to be admitted to the main burner without being smoothly ignited by the pilot flame. Each burner should be at room temperature at the begining of the test and should be tested in turn. )	-	42000	-
18.1(There shall be easy and safe access of lighting each burner by matchstick and it shall be easy to see that the burner is lighted)	-	42000	-
17.3(When the gas consumption of the burner is reduced to simmer, the flame shall not extinguish, blow off, strike back or form soot, when tested with commercial PNG at 21 mbar gas inlet pressure.)	-	42000	-
17.2(Burner-5)	-	42000	-
17.2(Burner-4)	-	42000	-
17.2(Burner-3)	-	42000	-
17.2(Burner-2)	-	42000	-
17.2(Burner-1)	-	42000	-
17.2(Sim Rating Declared)	-	42000	-
17.1.2(Total Gas Consumption)	-	42000	-
17.1(Burner-5)	-	42000	-
17.1(Burner-4)	-	42000	-
17.1( Burner-3)	-	42000	-
17.1( Burner-2)	-	42000	-
17.1( Burner-1)	-	42000	-
17.1(Rating Declared)	-	42000	-
15.2(Fragmentation test of the toughened glass to )	-	42000	-
15.1(Verification of the strength of the gas stove surface of the toughened glass top against thermal stress)	-	42000	-
15(Width wise deflection)	-	42000	-
15(Length wise deflection)	-	42000	-
15(Vertical Deflection)	-	42000	-
14.5(The position of the gas inlet shall allow connection to a gas supply on either side of the appliances, the rear end or bottom is also permitted. It shall be possible to change gas inlet from one side to other side easily by standard tools.)	-	42000	-
14.4(Any other connection made from the main gas rail shall be only metallic.)	-	42000	-
14.4(The external surface of the gas rail shall be treated to resist corrosion)	-	42000	-
14.4(The wall thickness of main gas rail)	-	42000	-
14.4(The pipe/tube used for main gas rail shall be of mild steel)	-	42000	-
14.3(Screwed gas Inlet and outlet connections shall confirm to IS:554, Declared by party)	-	42000	-
14.2((e))	-	42000	-
14.2((d))	-	42000	-
14.2(( c))	-	42000	-
14.2((b))	-	42000	-
14.2(Shape of Nozzles as per fig. 3 : (a))	-	42000	-
14.2(Where Nozzles for flexible tubing are fitted, they shall be so positioned as to facilitate fitting of the tubing and also to prevent heating of the tubing to more than 60°C)	-	42000	-
14.1(Nozzle shall be machined from free cutting brass, MS, SS, Zinc)	-	42000	-
13(All gas carrying parts of the appliances should be sound and these parts when connected to form complete assembly shall also be sound against any gas leakage. The complete assembly shall be checked at 14.71 kN/m²)	-	42000	-
12.1.2(The material of the pan support shall be metallic.)	-	42000	-
12.1.1(Loose Pan support shall be so designed that it is not possible to place them firmly in other than proper position)	-	42000	-
12.1(Prongs of the Support shall have suitable taper to accommodate round bottom pans.)	-	42000	-
12.1(The design of the pan supports shall be such that it is practicable to support a pan of 100 mm diameter over at least one top burner without the use of loose rings and such that 125 mm diameter vessel remains stable over each burner. )	-	42000	-
11.7(The appliance comprising two or more burners shall include one burner having a rating of at least 1450 kCal/hr, based on net calorific value of the gas (When using domestic PNG))	-	42000	-
11.6(For Burners having centre flame, provision shall be made to protect the centre flame from pan resting directly on burner top and smothering the centre flame. )	-	42000	-
11.5(If the burner is made and assembled in two or more parts they shall be so designed to provide proper self locating arrangement so that they are always reassembled to its original design preventing any maladjustment in their assembly. This shall also be applicable for primary air regulators.)	-	42000	-
11.4(If primary air regulators are used, they shall be so designed that they are not easily maladjusted by the user and the construction shall be such that primary air adjustment can be made with the burner in place.)	-	42000	-
11.3(The tightness of the joints in the burner assembly shall not be depended upon adhesives or any kind of packing.)	-	42000	-
11.2(The Burner supports shall be rigid and shall be fixed in their place. Their construction shall ensure the stability of the burners and shall prevent their undue movement in a horizontal plane.)	-	42000	-
11.1(The construction of the burners and the assembly shall allow their dismantling from the supports easily with or without the use of tools)	-	42000	-
10.2(The Size of the jet in Litres per hour of flow of PNG at STP conditions shall be impressed upon it.)	-	42000	-
10.1.1(Injector Jet shall be made of metal , with or without ceramic tip. The melting point of the metal shall not be less than 650°C)	-	42000	-
10.1(Dimension- Threads)	-	42000	-
10.1(Dimension- Projection from the face of mounting, Nominal)	-	42000	-
10.1(Dimension- Across Flats)	-	42000	-
10.1(The Injector Jets shall be fixed calibrated type and it shall not be possible to loosen them without the use of tools.)	-	42000	-
9.12(The noting means adopted shall be sufficiently robust to withstand normal use without distortion or damage.)	-	42000	-
9.11.1(Simmer flame shall be obtained by fixed simmer orifice.)	-	42000	-
9.11(Taps having an 'OFF' position shall have positive stops at the 'OFF' and simmer position except that special purpose taps (for appliance incorporating auto or self ignition device))	-	42000	-
9.1(Screw-down valves shall be so designed that it is impossible to withdraw completely the valve stem in the normal operation of the tap.)	-	42000	-
9.9(Screws nuts etc., which regulate the tension of taps valve or springs shall not loosen in operation of the appliance. It shall not be possible to cause a leak during normal manual operation of tap.)	-	42000	-
9.8(All controls or taps shall be easy to operate at all temperatures normally attained in use)	-	42000	-
9.7(C1)	-	42000	-
9.7(B1)	-	42000	-
9.7(A1)	-	42000	-
9.7(D)	-	42000	-
9.7(C)	-	42000	-
9.7(B)	-	42000	-
9.7(A)	-	42000	-
9.7(Dimension of Taper plugs in off position:)	-	42000	-
9.6(Each taper plug tap shall be spring loaded to maintain a gas tight fit. Helical springs fitted in taps and valves shall have flattened ends, which shall be rounded before fitting.)	-	42000	-
9.5.1(Taps shall be lubricated with suitable grease, resistant to the action of the gas and capable of operating at the maximum temperature of 110°C.)	-	42000	-
9.5(Taps shall be so made that in normal use and reasonable application of lubricant, the gas passages do not become blocked.)	-	42000	-
9.4(Preferably all taps (Excluding pilot taps) should lock in the off position, but in all cases it shall be impossible to handle or tap to move accidentally…. )	-	42000	-
9.3(When Taps are fitted with adjustable stops, there shall be means of looking the stops in position. If screws are used for this purpose, they shall not lead into gas passages.)	-	42000	-
9.2(Taps shall be designed so that when placed in any position and viewed from a distance of 3 m, will definitely indicate whether the valve is open, closed or in intermediate position.)	-	42000	-
9.2(All Taps shall close in the same direction. The direction of rotation of knob from off-on-simmer shall be anti-clockwise.)	-	42000	-
9.2(The 'ON' "OFF" and any fixed position of tap handles shall be clearly and durably indicated or shall be obvious by design or position else some indication shall be provided.)	-	42000	-
9.1(The Appliance shall have at least one tap for each burner)	-	42000	-
8.7(The external Finished surfaces shall be easily cleanable.)	-	42000	-
8.6(All springs, screws, nuts and bolts which are visible or to be removed for maintenance, shall be of corrosion-resistant material or treated to resist corrosion.)	-	42000	-
8.5(Concealed Gas Supplies: Concealed tubular fittings liable to corrode shall be protected by bituminous paint or other equally protective material.)	-	42000	-
8.4 (b)(Resistance to Heating)	-	42000	-
8.4 (a)(Resistance to Abrasion)	-	42000	-
8.3.3(Corrosion Resistance test)	-	42000	-
8.3.2(Adhesion Test)	-	42000	-
8.3.1(Thickness of Chromium coating)	-	42000	-
8.3(Thickness of Nickel coating of the top flat surface of the body of electroplated stove.)	-	42000	-
8.2(Vitreous enameled component shall meet the requirement when tested in accordance with Annex E of IS:5116)	-	42000	-
8.1(The finishes shall, on visual examination, show no defects, such as pin-holes, blisters, roughness or exposed area of metal, which give rise to undualy rapid deterioration in use.)	-	42000	-
8.1(Parts, which will come in contact with the foodstuff, shall be capable of being hygienically cleaned.)	-	42000	-
8.1(The Finish of exposed parts shall be durable, easy to clean and not subject to excessive deterioration in normal use.)	-	42000	-
7(Rigidity and Stability : The appliance shall be so designed that it remains stable and shall not be easily overturned.)	-	42000	-
6.7(Thickness of Sheet)	-	42000	-
6.6(All nuts, bolts and fittings having spanner flats shall be capable of being moved by suitable spanner or be readily accessible to an adjustable spanner.)	-	42000	-
6.5(Parts, which are intented to be removable by the user, shall be easy to replace correctly and difficult to assemble incorrectly.)	-	42000	-
6.4(Burners and parts of Burner only of same rating , model and make shall be interchangeable or replaceable without effecting performance.)	-	42000	-
6.3(Burner ports shall be so designed and located that in normal use spilage of food shall not cause internal fouling of mixing tube and or blockage of injector jet.)	-	42000	-
6.2(The relative distance between the centres of the adjoining burner-)	-	42000	-
6.2(the parts of the burner shall not become disconnected during operation of the appliance.)	-	42000	-
6.1(The appliance, including all the component parts, shall be easy to clean and maintain in good working order, there shall be easy access to the accessories and controls for maintenance and adjustment.)	-	42000	-
5.8.3(The number of glass fragments contained in a 50 mm side square, when tested as Cl. 15.2)	-	42000	-
5.8.3(Toughened glass shall fragment into small particles.)	-	42000	-
5.8.2(Pan support for an uncovered burner in contact with the glass ceramic surface.The surface area of the pan support in contact with the glass ceramic)	-	42000	-
5.8.2(The toughened glass top shall ensure durability against damage in normal use)	-	42000	-
5.8.2(The means to hold the glass top of the gas stove shall not allow any stress or risk of mechanical change to the glass top.)	-	42000	-
5.8.1(Toughened glass top including their edges or corners shall not have fissures or scratches)	-	42000	-
5.7(Drip tray if provided shall be made of non-corrosive material)	-	42000	-
5.6(Meltiing poin of metal used in oven, griller or auxilliary or anyother combination)	-	42000	-
5.6(Melting point of metal for burner top)	-	42000	-
5.5(The main body of the burner including mixer head, mixing tube and burner head shall be of substantial and durable construction)	-	42000	-
5.4(Change in weight or volume of a non metallic material, when immerse in n-Pentane or PNG for 72 hours)	-	42000	-
5.3(Mercurous Nitrate test for copper and copper alloy Parts)	-	42000	-
5.2(The burner parts shall not melt or distort when burner is operated with flames flashed back for half an hour in the mixing tube.)	-	42000	-
5.1.1(Plastic components which are liable to heating (For example, tap handles push buttons etc.) shall be free of fissures, distortion, blemishes and discolouration)	-	42000	-
5.1(The use of low pressure rubber or plastic tubing fitted or pushed on nozzle is not recommended.)	-	42000	-
5.1(If flexible tubing is used, it shall not be fitted on the outlet side of any control which is capable of cutting of the gas completely, except where screwed metal connection are fitted.)	-	42000	-
5.1(The appliance shall be free from swarf, grit and other foreign matters.)	-	42000	-
4.3(No pressure regulator shall be included as part of the stove.)	-	42000	-
4.2(Rivets, Fastening screws and plugs , etc. shall not lead into gas passages.)	-	42000	-
4.1(The construction of all the parts of equipment shall be sound and of high standard of workmanship and appropriate finish. The construction shall ensure durability and shall comply with the safety requirements.)	-	42000	-
4.1(General)	-	42000	-
4.2(General)	-	42000	-
4.3(General)	-	42000	-
5.1(Materials)	-	42000	-
5.1(Materials)	-	42000	-
5.1(Materials)	-	42000	-
5.1(Materials)	-	42000	-
5.1.1(Materials)	-	42000	-
5.2(Materials)	-	42000	-
5.3(Materials)	-	42000	-
5.4(Materials)	-	42000	-
5.5(Materials)	-	42000	-
5.5(Materials)	-	42000	-
5.5(Materials)	-	42000	-
5.7(Materials)	-	42000	-
5.8.1(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (a)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (b)(Materials)	-	42000	-
26(Thermal Efficiency)	-	42000	-
5.8.2 (c )(Materials)	-	42000	-
25.2(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (d)(Materials)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (d)(Materials)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
25.1(Fire Hazard and Limiting Temperature)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
24.2(Combustion)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
24.1(Combustion)	-	42000	-
5.8.2 (e)(Materials)	-	42000	-
24.1(Combustion)	-	42000	-
5.8.3 (a)(Materials)	-	42000	-
23(Resistance to Draught)	-	42000	-
5.8.3 (b)(Materials)	-	42000	-
5.8.3 (c)(Materials)	-	42000	-
22(Formation of soot)	-	42000	-
21(Flash Back)	-	42000	-
5.8.3 (d)(Materials)	-	42000	-
20(Noise Control)	-	42000	-
5.8.3 (e)(Materials)	-	42000	-
5.8.3 (f)(Materials)	-	42000	-
19.3(Flame Stability)	-	42000	-
6.1(Design for Maintenance)	-	42000	-
19.2(Flame Stability)	-	42000	-
6.1(Design for Maintenance)	-	42000	-
19.1.1(Flame Stability)	-	42000	-
6.2(Design for Maintenance)	-	42000	-
6.2(Design for Maintenance)	-	42000	-
19.1(Flame Stability)	-	42000	-
6.3(Design for Maintenance)	-	42000	-
18.4(Ignition and Flame Travel)	-	42000	-
6.4(Design for Maintenance)	-	42000	-
18.3(Ignition and Flame Travel)	-	42000	-
6.5(Design for Maintenance)	-	42000	-
18.2(Ignition and Flame Travel)	-	42000	-
18.1(Ignition and Flame Travel)	-	42000	-
18.1(Ignition and Flame Travel)	-	42000	-
6.6(Design for Maintenance)	-	42000	-
17.0(Gas Consumption)	-	42000	-
6.7(Design for Maintenance)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-
9.11(Gas Taps)	-	42000	-
7.1(Rigidity and Stability)	-	42000	-
7.2(Rigidity and Stability)	-	42000	-
7.3(Rigidity and Stability)	-	42000	-
8.1(Workmanship and Finish)	-	42000	-
8.1(Workmanship and Finish)	-	42000	-
8.2 & 8.2.1(Workmanship and Finish)	-	42000	-
8.3(Workmanship and Finish)	-	42000	-
8.3(Workmanship and Finish)	-	42000	-
8.3.2(Workmanship and Finish)	-	42000	-
8.4 (a)(Workmanship and Finish)	-	42000	-
8.4 (b)(Workmanship and Finish)	-	42000	-
8.5(Workmanship and Finish)	-	42000	-
8.6(Workmanship and Finish)	-	42000	-
8.7(Workmanship and Finish)	-	42000	-
9.1(Gas Taps)	-	42000	-
9.2(Gas Taps)	-	42000	-
9.2(Gas Taps)	-	42000	-
9.2(Gas Taps)	-	42000	-
9.3(Gas Taps)	-	42000	-
9.4(Gas Taps)	-	42000	-
9.5(Gas Taps)	-	42000	-
9.11.1(Gas Taps)	-	42000	-
9.12(Gas Taps)	-	42000	-
10.1(Injector Jets)	-	42000	-
10.1 (a)(Injector Jets)	-	42000	-
10.1 (b)(Injector Jets)	-	42000	-
10.1 (c )(Injector Jets)	-	42000	-
10.1.1(Injector Jets)	-	42000	-
9.5.1(Gas Taps)	-	42000	-
10.2(Injector Jets)	-	42000	-
9.6(Gas Taps)	-	42000	-
11.1(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.2(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.3(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.4(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.5(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.6(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
11.7(Burners)	-	42000	-
9.7(Gas Taps)	-	42000	-
9.8(Gas Taps)	-	42000	-
9.9(Gas Taps)	-	42000	-
9.10(Gas Taps)	-	42000	-
12.1(Pan Supports)	-	42000	-
12.1.1(Pan Supports)	-	42000	-
12.1.2(Pan Supports)	-	42000	-
13.1(Gas Soundness)	-	42000	-
14.1(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.2(Gas Inlet Connection)	-	42000	-
14.3(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.4(Gas Inlet Connection)	-	42000	-
14.5(Gas Inlet Connection)	-	42000	-
14.5(Gas Inlet Connection)	-	42000	-
14.5(Gas Inlet Connection)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
15.0(Strength and Rigidity)	-	42000	-
17.0(Gas Consumption)	-	42000	-
17.0(Gas Consumption)	-	42000	-

13 May, 2028

-
Included w.e.f.23.06.2025

IS 15558 (2024)

INSTANTANEOUS DOMESTIC WATER HEATER FOR USE WITH LPG SPECIFICATION First Revision of IS 15558

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Construction)	-	15000	-
4.1.2(Construction)	-	15000	-
4.1.3(Construction)	-	15000	-
4.1.4(Construction)	-	15000	-
4.1.5(Construction)	-	15000	-
4.1.6(Construction)	-	15000	-
4.1.7(Construction)	-	15000	-
4.1.8(Construction)	-	15000	-
4.1.9(Construction)	-	15000	-
4.1.10(Construction)	-	15000	-
4.1.11(Construction)	-	15000	-
4.1.12(Construction)	-	15000	-
5.1(Materials)	-	15000	-
5.2(Materials)	-	15000	-
5.3(Materials)	-	15000	-
5.4(Materials)	-	15000	-
5.5(Materials)	-	15000	-
6.1(Connections)	-	15000	-
6.2(Connections)	-	15000	-
6.3(Connections)	-	15000	-
6.4(Connections)	-	15000	-
6.5(Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
6.6(Gas Inlet Connections)	-	15000	-
7(Flame Visibility)	-	15000	-
8(Gas Taps)	-	15000	-
9(Flame Failure Device)	-	15000	-
10(Ignition Device)	-	15000	-
11(Protection Against Accidental Overheating)	-	15000	-
12(Water Rate Adjuster)	-	15000	-
14(Gas Soundness)	-	15000	-
15(Water Soundness)	-	15000	-
16(Thermal Efficiency)	-	15000	-
16(Thermal Efficiency)	-	15000	-
17(Combustion)	-	15000	-
18(Gas Consumption)	-	15000	-
19.1(Ignition and flame travel)	-	15000	-
19.2(Ignition and flame travel)	-	15000	-
19.3(Ignition and flame travel)	-	15000	-
20(Flame Stability)	-	15000	-
21(Noise Control)	-	15000	-
22(Flash Back)	-	15000	-
23(Resistance to Draught)	-	15000	-
24(Fire Hazard And Limiting Temperature )	-	15000	-
24(Fire Hazard And Limiting Temperature)	-	15000	-
24(Fire Hazard And Limiting Temperature)	-	15000	-
24(Fire Hazard And Limiting Temperature)	-	15000	-
25(Time For Temperature Rise)	-	15000	-
26(Hot Water Output Test)	-	15000	-
27(Marking)	-	15000	-
Cl-4(General Requirements)	-	15000	-
Cl-5.1(water heater)	-	15000	-
Cl-5.2(copper and copper alloy)	-	15000	-
Cl-5.3(Non-metallic materials)	-	15000	-
Cl-5.4(Mixing tube and burner head)	-	15000	-
Cl-6.3(All Water connections)	-	15000	-
Cl-6.4(water inlet and outlet connections)	-	15000	-
Cl-6.6(Gas Inlet Connections)	-	15000	-
Cl-7(Flame visibility)	-	15000	-
Cl-8(Gas Taps)	-	15000	-
Cl-9(Flame failuse device)	-	15000	-
Cl-11(Protection against accidental overheating)	-	15000	-
Cl-13(General condition of test)	-	15000	-
Cl-14(Gas Soundness)	-	15000	-
Cl-15(Water Soundness)	-	15000	-
Cl-16(Thermal efficiency)	-	15000	-
Cl-17(carbon monoxide/carbon dioxide)	-	15000	-
Cl-18(Gas Consumption)	-	15000	-
Cl-19(Ignition and flame travel)	-	15000	-
Cl-20(FLAME STABILITY)	-	15000	-
Cl-21(NOISE CONTROL)	-	15000	-
Cl-22(FLASH-BACK)	-	15000	-
Cl-24("FIRE HAZARDS AND LIMITING TEMPERATURE")	-	15000	-
Cl-25(TIME FOR TEMPERATURE RISE)	-	15000	-
Cl-26(HOT WATER OUTPUT TEST)	-	15000	-

13 May, 2028

-
Included w.e.f.17.06.2025

IS 302 : Part 2 : SEC 31 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 31 range hoods

All

34000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	34000	-
Clause No - 5.18(linear and angular dimension)	-	34000	-
Clause No - 6.2(harmfull ingress of water)	-	34000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	34000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	34000	-
Clause No - 8.2(Addition)	-	34000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	34000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	34000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	34000	-
Clause No - 14(Impulse test voltage)	-	34000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	34000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	34000	-
Clause No -19.11.4.1(electrostatic discharge)	-	34000	-
Clause No -19.11.4.2(radiated field)	-	34000	-
Clause No -19.11.4.3(fast transient)	-	34000	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	34000	-
Clause No -21.1(Mechanical strength)	-	34000	-
Clause No -22.1(construction)	-	34000	-
Clause No -22.11(push force applied)	-	34000	-
Clause No -24.1.2(safety isolating transformer)	-	34000	-
Clause No -24.1.3(for switches)	-	34000	-
Clause No -24.1.4(for automatic control)	-	34000	-
Clause No -24.1.5(for innterconnection couplers)	-	34000	-
Clause No -24.4(plug and socket)	-	34000	-
Clause No -25.8, Table no -11(conductor resistance)	-	34000	-
Clause No -25.5(dimension for pins)	-	34000	-
Clause No -27.6(for circuit board)	-	34000	-
Clause No -29.2(comparative tracking index)	-	34000	-
Clause No -29.3.3(dry heat test)	-	34000	-
Clause No -30.2.1(glow wire test)	-	34000	-
Clause No -30.101("incorporate combustible material")	-	34000	-
15(MOISTURE RESISTANCE)	-	34000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	34000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	34000	-
18(ENDURANCE)	-	34000	-
28(SCREWS AND CONNECTIONS)	-	34000	-
31(RESISTANCE TO RUSTING)	-	34000	-
19.11.4.5(Immunity to conducted discharges)	-	34000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	34000	-
19.11.4.7(Harmonics)	-	34000	-
22(CONSTRUCTION)	-	34000	-
24(COMPONENTS)	-	34000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	34000	-
11(Heating)	-	34000	-
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	34000	-
Clause No - 5.18(linear and angular dimension)	-	34000	-
Clause No - 6.2(harmfull ingress of water)	-	34000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	34000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	34000	-
Clause No - 8.2(Addition)	-	34000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	34000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	34000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	34000	-
Clause No - 14(Impulse test voltage)	-	34000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	34000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	34000	-
Clause No -19.11.4.1(electrostatic discharge)	-	34000	-
Clause No -19.11.4.2(radiated field)	-	34000	-
Clause No -19.11.4.3(fast transient)	-	34000	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	34000	-
Clause No -21.1(Mechanical strength)	-	34000	-
Clause No -22.1(construction)	-	34000	-
Clause No -22.11(push force applied)	-	34000	-
Clause No -24.1.2(safety isolating transformer)	-	34000	-
Clause No -24.1.3(for switches)	-	34000	-
Clause No -24.1.4(for automatic control)	-	34000	-
Clause No -24.1.5(for innterconnection couplers)	-	34000	-
Clause No -24.4(plug and socket)	-	34000	-
Clause No -25.8, Table no -11(conductor resistance)	-	34000	-
Clause No -25.5(dimension for pins)	-	34000	-
Clause No -27.6(for circuit board)	-	34000	-
Clause No -29.2(comparative tracking index)	-	34000	-
Clause No -29.3.3(dry heat test)	-	34000	-
Clause No -30.2.1(glow wire test)	-	34000	-
Clause No -30.101("incorporate combustible material")	-	34000	-
15(MOISTURE RESISTANCE)	-	34000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	34000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	34000	-
18(ENDURANCE)	-	34000	-
28(SCREWS AND CONNECTIONS)	-	34000	-
31(RESISTANCE TO RUSTING)	-	34000	-
19.11.4.5(Immunity to conducted discharges)	-	34000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	34000	-
19.11.4.7(Harmonics)	-	34000	-
22(CONSTRUCTION)	-	34000	-
24(COMPONENTS)	-	34000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	34000	-
11(Heating)	-	34000	-
Clause No - 5(GENERAL CONDITIONS FOR THE TESTS)	-	34000	-
Clause No - 5.18(linear and angular dimension)	-	34000	-
Clause No - 6.2(harmfull ingress of water)	-	34000	-
Clause No - 8.1.1("PROTECTION AGAINST ACCESS TO LIVE PART- test probe B")	-	34000	-
Clause No - 8.1.2("PROTECTION AGAINST ACCESS TO LIVE PART - test probe 13")	-	34000	-
Clause No - 8.2(Addition)	-	34000	-
Clause No - 10.1, Table No. -1(power input deviation)	-	34000	-
Clause No - 13.3("LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE")	-	34000	-
Clause No - 13.3,Table No.- 4(voltage for electrical strength)	-	34000	-
Clause No - 14(Impulse test voltage)	-	34000	-
Clause No - 15.1.1(MOISTURE RESISTANCE)	-	34000	-
Clause No -19.7(test is repeated with the capacitor short circuited)	-	34000	-
Clause No -19.11.4.1(electrostatic discharge)	-	34000	-
Clause No -19.11.4.2(radiated field)	-	34000	-
Clause No -19.11.4.3(fast transient)	-	34000	-
Clause No -19.11.4.4(Voltage dips and interruption)	-	34000	-
Clause No -21.1(Mechanical strength)	-	34000	-
Clause No -22.1(construction)	-	34000	-
Clause No -22.11(push force applied)	-	34000	-
Clause No -24.1.2(safety isolating transformer)	-	34000	-
Clause No -24.1.3(for switches)	-	34000	-
Clause No -24.1.4(for automatic control)	-	34000	-
Clause No -24.1.5(for innterconnection couplers)	-	34000	-
Clause No -24.4(plug and socket)	-	34000	-
Clause No -25.8, Table no -11(conductor resistance)	-	34000	-
Clause No -25.5(dimension for pins)	-	34000	-
Clause No -27.6(for circuit board)	-	34000	-
Clause No -29.2(comparative tracking index)	-	34000	-
Clause No -29.3.3(dry heat test)	-	34000	-
Clause No -30.2.1(glow wire test)	-	34000	-
Clause No -30.101("incorporate combustible material")	-	34000	-
15(MOISTURE RESISTANCE)	-	34000	-
16(LEAKAGE CURRENT AND ELECTRIC STRENGTH)	-	34000	-
17(OVERLOAD PROTECTION OF TRANSFORMERS AND ASSOCIATED CIRCUITS)	-	34000	-
18(ENDURANCE)	-	34000	-
28(SCREWS AND CONNECTIONS)	-	34000	-
31(RESISTANCE TO RUSTING)	-	34000	-
19.11.4.5(Immunity to conducted discharges)	-	34000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	34000	-
19.11.4.7(Harmonics)	-	34000	-
22(CONSTRUCTION)	-	34000	-
24(COMPONENTS)	-	34000	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	34000	-
11(Heating)	-	34000	-

13 May, 2028

-
Included w.e.f 02.07.2025 Exclusion: Cl 19.11.4.1-19.11.4.7(EMI/EMC)

IS 7231 (2021)

Plastic flushing cisterns for water closets and urinals - Specification (third revision)

ALL

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Construction of Exposed Cistern)	-	15000	-
5.1.1(Construction of Exposed Cistern)	-	15000	-
5.1.1(Construction of Exposed Cistern)	-	15000	-
5.1.2(Construction of Cover)	-	15000	-
5.1.3(Construction of Flush Pipe)	-	15000	-
5.1.3.1(Flush pipe connection to cistern)	-	15000	-
5.1.3.1(Flush pipe connection to cistern)	-	15000	-
5.1.3.1(Flush pipe connection to cistern)	-	15000	-
5.1.3.1(Flush pipe connection to cistern)	-	15000	-
5.1.4(Inlet and Overflow Holes)	-	15000	-
5.1.5(Float Valve)	-	15000	-
5.1.6(Operating Mechanism (Push-Knob))	-	15000	-
5.1.6(Operating Mechanism (Push-Knob))	-	15000	-
5.1.7(Overflow Pipe)	-	15000	-
5.1.7.2(Overflow Pipe)	-	15000	-
5.1.7.3(Overflow Pipe)	-	15000	-
5.2.1(Concealed Cistern)	-	15000	-
5.2.1(Concealed Cistern- Construction)	-	15000	-
5.2.2(Flush Pipe)	-	15000	-
5.2.3(Operating Mechanism)	-	15000	-
5.2.3(Operating Mechanism)	-	15000	-
6, 6.1(Finish)	-	15000	-
6.1(Finish)	-	15000	-
6.1(Finish)	-	15000	-
6.2(Finish)	-	15000	-
7.1(Operational and Performance Requirement- Flushing Arrangement)	-	15000	-
7.2(Working Water Level)	-	15000	-
7.3(Freedom from Leakage)	-	15000	-
7.4(Reduced Water Level)	-	15000	-
7.5 (a)(Cistern Discharge Capacity 6/3 Litres)	-	15000	-
7.5 (a)(Cistern Discharge Capacity 6/3 Litres)	-	15000	-
7.5 (b)(Cistern Discharge Capacity 4.8/2.8 litres)	-	15000	-
7.5 (b)(Cistern Discharge Capacity 4.8/2.8 litres)	-	15000	-
7.5 (c)(Cistern Discharge Capacity 4/2 litres)	-	15000	-
7.5 (c)(Cistern Discharge Capacity 4/2 litres)	-	15000	-
7.6 (a)(Discharge Rate)	-	15000	-
7.6 (b)(Discharge Rate)	-	15000	-
7.6 (c)(Discharge Rate)	-	15000	-
7.6(Discharge Rate)	-	15000	-
8.1(Distortion Resistance Test)	-	15000	-
8.2(Dead Load Test)	-	15000	-
8.3(Front Thrust Test)	-	15000	-
8.4(Impact Test)	-	15000	-
8.4.1(Impact Test)	-	15000	-
9.3(Endurance Test)	-	15000	-

13 May, 2028

-
Included w.e.f.11.06.2025

IS 4250 (2025)

Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers ï¿½ Specification ( Second Revision )

All

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(General Requirements)	-	16000	-
Cl-5(General Conditions for the tests)	-	16000	-
Cl-6(Classification)	-	16000	-
Cl-7(Marking)	-	16000	-
Cl-8(Safety Requirements)	-	16000	-
Cl-9(Endurance fpr motor and base assembly)	-	16000	-
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	16000	-
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	16000	-
Cl-10.4(Idli Batter)	-	16000	-
Cl-10.5(Operational Tests for Juicers)	-	16000	-
Cl-11(Temperature Withstand Test for Bowl)	-	16000	-
Cl-12.1(Test for Switches)	-	16000	-
Cl-13(Strength of Assembly)	-	16000	-
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	16000	-
Cl-14.2, Table-2 (ii)(Power input and current)	-	16000	-
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	16000	-
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	16000	-
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	16000	-
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	16000	-
Cl-19.11.4.1(Electrostatic discharges)	-	16000	-
Cl-19.11.4.2(Radiated fields)	-	16000	-
Cl-19.11.4.3(Fast transient bursts)	-	16000	-
Cl-19.11.4.4(Surge immunity test)	-	16000	-
Cl-19.11.4.5(Immunity to conducted discharges)	-	16000	-
Cl-19.11.4.6(Class 3 Voltage dips and interruptions)	-	16000	-
Cl-19.11.4.7(Harmonics)	-	16000	-
Cl-4(General Requirements)	-	16000	-
Cl-5(General Conditions for the tests)	-	16000	-
Cl-6(Classification)	-	16000	-
Cl-7(Marking)	-	16000	-
Cl-8(Safety Requirements)	-	16000	-
Cl-9(Endurance fpr motor and base assembly)	-	16000	-
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	16000	-
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	16000	-
Cl-10.4(Idli Batter)	-	16000	-
Cl-10.5(Operational Tests for Juicers)	-	16000	-
Cl-11(Temperature Withstand Test for Bowl)	-	16000	-
Cl-12.1(Test for Switches)	-	16000	-
Cl-13(Strength of Assembly)	-	16000	-
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	16000	-
Cl-14.2, Table-2 (ii)(Power input and current)	-	16000	-
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	16000	-
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	16000	-
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	16000	-
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	16000	-
Cl-19.11.4.1(Electrostatic discharges)	-	16000	-
Cl-19.11.4.2(Radiated fields)	-	16000	-
Cl-19.11.4.3(Fast transient bursts)	-	16000	-
Cl-19.11.4.4(Surge immunity test)	-	16000	-
Cl-19.11.4.5(Immunity to conducted discharges)	-	16000	-
Cl-19.11.4.6(Class 3 Voltage dips and interruptions)	-	16000	-
Cl-19.11.4.7(Harmonics)	-	16000	-

13 May, 2028

-
Included w.e.f 02.07.2025 Exclusion: Cl 19.11.4.1-19.11.4.7(EMI/EMC)

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	10000	-
7.0(Dimension and Tolerances)	-	10000	-
8.1 Table-1(Al)	-	10000	-
8.1 Table-1(Cu)	-	10000	-
8.1 Table-1(Mg)	-	10000	-
8.1 Table-1(Si)	-	10000	-
8.1 Table-1(Fe)	-	10000	-
8.1 Table-1(Mn)	-	10000	-
8.1 Table-1(Zn)	-	10000	-
8.1 Table-1(Ti)	-	10000	-
8.1 Table-1(Cr)	-	10000	-
9.1(Tensile Strength)	-	10000	-
9.3(Wrapping Test)	-	10000	-
10(Selection of Test Samples)	-	10000	-

13 May, 2028

-
Included w.e.f 10.06.2025

IS 17569 (2021)

Insulated Containers for Food Storage — Specification

ALL

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Manufacture and Workmanship)	-	28000	-
5.3(Manufacture and Workmanship)	-	28000	-
7.1(Material)	-	28000	-
7.1.2(Thickness)	-	28000	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Lead)	-	28000	-
7.1.2.1(Requirements and Tests(Material) – Outer Protective Case and Accessories – Cadmium)	-	28000	-
7.1.2.8(Bisphenol A(BPA))	-	28000	-
7.3(Capacity)	-	28000	-
7.4(Heat Retention Capability)	-	28000	-
7.5(Cold Retention Capability)	-	28000	-
7.6.1(Drop Impact Test)	-	28000	-
7.6.2(Pendulum Impact Test)	-	28000	-
7.7(Fixing Strength of the Handle)	-	28000	-
7.8(Test for Strength of Shoulder Strap)	-	28000	-
7.9(Leakage Test)	-	28000	-
7.10(Joint Leak Test)	-	28000	-
7.11(Staining Test)	-	28000	-
7.12("Check for PUF (Polyurethane Foam) or any Other Similar Thermal Insulation Material ")	-	28000	-
7.13.1(Length of the Shoulder Strap)	-	28000	-
7.13.2(Stability of Insulated Container)	-	28000	-
7.13.3(Cleaning)	-	28000	-
7.14(Seepage Test)	-	28000	-
9.1(Marking)	-	28000	-
9.2(BIS certification marking)	-	28000	-
10(Packaging)	-	28000	-
CLAUSE 5.2(Welding Defects)	-	28000	-
CLAUSE 7.1(Materials)	-	28000	-
CLAUSE 7.1.2.2(Thickness of plastic)	-	28000	-
"CLAUSE 7.1.2.1 "(Minimum Thickness of Outer Container)	-	28000	-
"CLAUSE 7.1.2.1 "(Coating Thickness)	-	28000	-
"CLAUSE 7.1.2.1 "(Salt Water Corrosion Test)	-	28000	-
CLAUSE 7.1.2.1(Adhesion Test)	-	28000	-
CLAUSE 7.1.2.1(Lead Limit)	-	28000	-
CLAUSE 7.1.2.1(Cadmium Limit)	-	28000	-
CLAUSE 7.1.2.3(Outer container or lid - thickness)	-	28000	-
CLAUSE 7.3(Capacity)	-	28000	-
CLAUSE 7.4(Heat Retention Capability)	-	28000	-
CLAUSE 7.5(Cold Retention Capability)	-	28000	-
CLAUSE 7.6.1(Drop Impact)	-	28000	-
CLAUSE 7.6.2(Pendulum Impact)	-	28000	-
CLAUSE 7.7(Fixing Strength of Handle)	-	28000	-
CLAUSE 7.8(Test for Strength of Shoulder Strap)	-	28000	-
CLAUSE 7.9(Leakage Test)	-	28000	-
CLAUSE 7.10(Joint Leak Test)	-	28000	-
CLAUSE 7.11(Staining Test)	-	28000	-
CLAUSE 7.12(Checking of PUF insulation)	-	28000	-
CLAUSE 7.13.1(Length of the Shoulder Strap)	-	28000	-
CLAUSE 7.13.2(Stability of Flask)	-	28000	-
CLAUSE 7.1.1(Material - inner container)	-	28000	-
C 7.1.1 Note Annex C(Test for leaching of food grade stainless steel)	-	28000	-
CL 7.1.1 Note- Annex D(Sensational test method)	-	28000	-
Cl 7.1.2.2(Polymer - test for BPA)	-	28000	-
Cl 7.1.2.4(Silicon gasket - overall migration)	-	28000	-
Cl 7.1.2.4(Silicon gasket - defects)	-	28000	-
Cl 7.1.2.5(Performance requirement for glass lid - Fragmentation test (Cl 8.15.1 of IS 2347))	-	28000	-
Cl 7.1.2.5(Performance requirement for glass lid - Ball drop test (Cl 8.15.2 of IS 2347))	-	28000	-
Cl 7.1.2.5(Performance requirement for glass lid - Thermal shock test (Cl 8.15.3 of IS 2347))	-	28000	-
Cl 7.1.2.5(Performance requirement for glass lid - Free fall test (Cl 8.15.4 of IS 2347))	-	28000	-
Cl 7.1.2.5(Thickness of steel rim)	-	28000	-
Cl 7.1.2.5(Thickness of glass lid)	-	28000	-
Cl 7.1.2.6(Thermal insulating material)	-	28000	-
Cl 7.1.2.7(Additional lid)	-	28000	-
Cl 7.1.2.8(Hot/Cold Box - thickness)	-	28000	-
Cl 7.1.2.9(Internal utensils- material)	-	28000	-
Cl 7.1.2.9(Internal utensils- thickness)	-	28000	-
Cl 7.1.2.9(Internal utensils - thickness of plastic lid)	-	28000	-
Cl 7.1.2.9(Test for BPA)	-	28000	-
CLAUSE 7.1.2.3(Outer container or lid - material)	-	28000	-

13 May, 2028

-
Included w.e.f 10.06.2025

IS 2347 (2023)

DOMESTIC PRESSURE COOKER ï¿½ SPECIFICATION

All

36000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Gross capacity)	-	36000	-
4.2(Body Capacity)	-	36000	-
5.1(Body, Lid, Containers and Grid)	-	36000	-
5.1.2(Body and Lid )	-	36000	-
5.1.3(Stainless steel pressure cooker)	-	36000	-
5.1.4(Aluminium cooker )	-	36000	-
5.2(Safety Relief Device)	-	36000	-
5.3(Gasket)	-	36000	-
5.4(Handles and Knobs)	-	36000	-
5.5(Pressure Regulating Device )	-	36000	-
5.6(Vent Seal Pin for Pressure Regulating Device )	-	36000	-
5.7(Vent Pipe )	-	36000	-
5.8(Vent Pipe Nut )	-	36000	-
5.9(Spring )	-	36000	-
5.1(Material of Rim )	-	36000	-
5.11(Visual Pressure Indicator)	-	36000	-
5.12(Gasket Release System)	-	36000	-
6(Construction)	-	36000	-
7(Workmanship and Finish )	-	36000	-
8.1(Air Pressure Test )	-	36000	-
8.2(Proof Pressure Test )	-	36000	-
8.3(Operating Test for Pressure Regulating Device )	-	36000	-
8.4(Test for Safety Relief Device )	-	36000	-
8.5(Bursting Pressure Test )	-	36000	-
8.6(Test for Removal of Lid under Pressure )	-	36000	-
8.7(Test for Spring Loaded Mechanism )	-	36000	-
8.8(Composite Cooker Base )	-	36000	-
8.9(Aluminium induction compatible Base )	-	36000	-
8.1(Handles of cooker )	-	36000	-
8.11(External Coating)	-	36000	-
8.12(Internal Coating )	-	36000	-
8.13(Integral electrical heating)	-	36000	-
8.14(Ply construction cooker Body )	-	36000	-
8.15.1(Fragmentation Test )	-	36000	-
8.15.2(Ball Drop Test )	-	36000	-
8.15.3(Thermal Shock Test )	-	36000	-
8.15.4(Free Fall Test)	-	36000	-
8.17(Test for Effectiveness for Induction Bottom)	-	36000	-
11(Marking )	-	36000	-
12(Packing )	-	36000	-
4(Capacity)	-	36000	-
4.2(Body Capacity)	-	36000	-
5.1.1(Body, Lid, Containers and Grid)	-	36000	-
5.1.2(Body, Lid, Containers and Grid)	-	36000	-
5.1.3(Body, Lid, Containers and Grid)	-	36000	-
5.1.4(Body, Lid, Containers and Grid)	-	36000	-
5.1.5(Body, Lid, Containers and Grid)	-	36000	-
5.2.1(Destructive Type Safety Relief Device)	-	36000	-
5.2.2(Resettable Type Safety Relief Device)	-	36000	-
5.3(Gasket)	-	36000	-
5.4(Handles and Knobs)	-	36000	-
5.5(Pressure Regulating Device)	-	36000	-
5.6(Vent Seal Pin for Pressure Regulating Device)	-	36000	-
5.7(Vent Pipe)	-	36000	-
5.8(Vent Pipe Nut)	-	36000	-
5.9(Spring)	-	36000	-
5.10(Spring)	-	36000	-
5.11(Visual Pressure Indicator)	-	36000	-
5.12(Gasket Release System)	-	36000	-
6(CONSTRUCTION)	-	36000	-
6.1(Pressure Regulating Device)	-	36000	-
6.1.1(Pressure Regulating Device)	-	36000	-
6.1.1(Minimum Inside diameter of Vent Pipe.)	-	36000	-
6.1.2(Pressure Regulating Device)	-	36000	-
6.1.3(Pressure Regulating Device)	-	36000	-
6.1.4(Pressure Regulating Device)	-	36000	-
6.1.5(Pressure Regulating Device)	-	36000	-
6.1.6(Pressure Regulating Device)	-	36000	-
6.2(Safety Relief Device)	-	36000	-
6.2.1(Safety Relief Device)	-	36000	-
6.2.2(Safety Relief Device)	-	36000	-
6.2.3(Safety Relief Device)	-	36000	-
6.3.1(Temperature Responsive Safety Relief Device)	-	36000	-
6.3.2(Temperature Responsive Safety Relief Device)	-	36000	-
6.3.3(Temperature Responsive Safety Relief Device)	-	36000	-
6.4.1(Handles and Knobs)	-	36000	-
6.4.1.1(Handles and Knobs)	-	36000	-
6.4.2(Handles and Knobs)	-	36000	-
6.4.2.1(Handles and Knobs)	-	36000	-
6.5(CONSTRUCTION)	-	36000	-
6.6(CONSTRUCTION)	-	36000	-
6.7(Internal Level Marking)	-	36000	-
6.8(Internal Level Marking)	-	36000	-
7.1(WORKMANSHIP AND FINISH)	-	36000	-
7.2(WORKMANSHIP AND FINISH)	-	36000	-
8.17(Test for Effectiveness for Induction Bottom)	-	36000	-
8.16(PRD with chain)	-	36000	-
8.15.4.2(Glass lid without rim)	-	36000	-
8.15.4.1("Free Fall Test ( Glass lid with rim) ")	-	36000	-
8.15.3(Thermal Shock Test on Tempered Glass lid)	-	36000	-
8.15.2(Ball Drop Test on Tempered Glass lid)	-	36000	-
8.15.1(Fragmentation Test on Tempered Glass lid)	-	36000	-
8.14(3 ply construction cooker body)	-	36000	-
8.13(Pressure cooker with integral electrical heating)	-	36000	-
8.12(Internal Coating)	-	36000	-
7.3(WORKMANSHIP AND FINISH)	-	36000	-
7.4(WORKMANSHIP AND FINISH)	-	36000	-
8.1(Air Pressure Test)	-	36000	-
8.2(Proof Pressure Test)	-	36000	-
8.3.1(Operating Test for Pressure Regulating Device)	-	36000	-
8.4.1(Test for Safety Relief Device)	-	36000	-
8.4.2(Test for Safety Relief Device)	-	36000	-
8.4.2 NOTE(Test for Safety Relief Device)	-	36000	-
8.5(Bursting Pressure Test)	-	36000	-
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	36000	-
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	36000	-
8.6.3(Tests for Removal of Lid under Pressure: For Cooker Fastened by Screw Clamps or Any Other Locking Device)	-	36000	-
8.6.4(Tests for Removal of Lid under Pressure in case of electrical pressure cooker)	-	36000	-
8.7(Test for Spring Loaded Mechanism)	-	36000	-
8.8(Test for stainless steel cookers)	-	36000	-
8.9("For stainless steel, aluminium induction compatible base and 3 ply cooker")	-	36000	-
8.10(Testing of Handles of the cooker)	-	36000	-
8.10 Note 3(Testing of Handles of the cooker)	-	36000	-
8.10 Note 4(Testing of Handles of the cooker)	-	36000	-
8.10 Note 5(Testing of Handles of the cooker)	-	36000	-
8.10 Note 6(Testing of Handles of the cooker)	-	36000	-
8.10.1(Testing of Handles of the cooker)	-	36000	-
8.11.1(External Coating)	-	36000	-

13 May, 2028

-
Included w.e.f 06.06.2025

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

All

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.24(Annexure E)(on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-	13500	Single Burner SS Body – Rs. 7500/- Glass Top – Rs. 9500/- Double Burner SS Body – Rs. 8000/- Glass Top – Rs. 10500/- Three Burner SS Body – Rs. 9000/- Glass Top – Rs.11500/- Four Burner SS Body – Rs. 10000/- Glass Top – Rs. 12500/- Five Burner SS
Cl.23(There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-	13500	-
24 (Annex - E)(Combustion (CO and CO2 ratio))	-	13500	-
4.1(Requirement)	-	13500	-
5(Materials)	-	13500	-
6(Design for Maintenance)	-	13500	-
7(Rigidity and Stability)	-	13500	-
8(Workmanship and Finish)	-	13500	-
9(Gas Taps)	-	13500	-
10(Injector Jets)	-	13500	-
11(Burners)	-	13500	-
12(Burner Pan Supports)	-	13500	-
13.1(Gas Soundness)	-	13500	-
13.2(Gas Leak Detector)	-	13500	-
14(Gas Inlet Connections)	-	13500	-
15(Strength and Rigidity)	-	13500	-
16(General Conditions of Test)	-	13500	-
17.1.1(Gas Consumption)	-	13500	-
18(Ignition and Flame Travel)	-	13500	-
19(Flame Stability)	-	13500	-
20(Noise Control)	-	13500	-
21(Flash Back)	-	13500	-
22(Formation of Soot)	-	13500	-
23(Resistance to Draught)	-	13500	-
24(Combustion)	-	13500	-
25(Fire Hazard and Limiting Temperature)	-	13500	-
26(Thermal Efficiency)	-	13500	-
27.1(Type Tests)	-	13500	-
27.2(Routine Tests)	-	13500	-
29(Marking)	-	13500	-
30(Packing)	-	13500	-
5.1.2(Toughened glass- Adhesive tape)	-	13500	-
5.1.3(Thermal Shock test)	-	13500	-

13 May, 2028

-
Included w.e.f 04.06.2025

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	5500	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	5500	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	5500	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	5500	-
10(Tensile test)	-	5500	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	5500	-

13 May, 2028

-
Included w.e.f 04.06.2025

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

ALL

36000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(testing of handles of the cooker)	-	36000	-
8.9(Test for Spring Loaded Mechanism)	-	36000	-
8.8(Test for Spring Loaded Mechanism)	-	36000	-
8.7(Test for Spring Loaded Mechanism)	-	36000	-
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	36000	-
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	36000	-
8.5(Bursting Pressure Test)	-	36000	-
8.4(Test for Safety Pressure Relief Device)	-	36000	-
8.3(Operating Test for Pressure Regulating Device)	-	36000	-
8.2(Proof Pressure Test)	-	36000	-
8.1(Air Pressure Test)	-	36000	-
7.4(WORKMANSHIP AND FINISH)	-	36000	-
7.3(WORKMANSHIP AND FINISH)	-	36000	-
7.2(WORKMANSHIP AND FINISH)	-	36000	-
7.1(WORKMANSHIP AND FINISH)	-	36000	-
6.4.1.1(Handles and Knobs)	-	36000	-
6.4.1(Handles and Knobs)	-	36000	-
6.3.1(Temperature Responsive Pressure Relief Device)	-	36000	-
6.3.1(Temperature Responsive Pressure Relief Device)	-	36000	-
6.2.2(Safety Relief Device)	-	36000	-
6.2.1(Safety Relief Device)	-	36000	-
6.2(Safety Relief Device)	-	36000	-
6.1.5(Pressure Regulating Device)	-	36000	-
6.1.4(Pressure Regulating Device)	-	36000	-
6.1.3(Pressure Regulating Device)	-	36000	-
6.1.2(Pressure Regulating Device)	-	36000	-
6.1.1(Pressure Regulating Device)	-	36000	-
6.1(Pressure Regulating Device)	-	36000	-
6(CONSTRUCTION)	-	36000	-
5.9(Spring)	-	36000	-
5.8(Vent Pipe Nut)	-	36000	-
5.7(Vent Pipe)	-	36000	-
5.6(Vent Seal Pin for Pressure Regulating Device)	-	36000	-
5.5(Pressure Regulating Device)	-	36000	-
5.4(Handles and Knobs)	-	36000	-
5.3(Gasket)	-	36000	-
5.2(Safety Relief Device)	-	36000	-
5.1.4(Body, Lid, Containers and Grid)	-	36000	-
5.1.3(Body, Lid, Containers and Grid)	-	36000	-
5.1.2(Body, Lid, Containers and Grid)	-	36000	-
5.1.1(Body, Lid, Containers and Grid)	-	36000	-
4.1(Capacity)	-	36000	-
8.1(testing of handles of the cooker)	-	36000	-
8.9(Test for Spring Loaded Mechanism)	-	36000	-
8.8(Test for Spring Loaded Mechanism)	-	36000	-
8.7(Test for Spring Loaded Mechanism)	-	36000	-
8.6.2(Tests for Removal of Lid under Pressure For inner Lid Cooker)	-	36000	-
8.6.1(Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-	36000	-
8.5(Bursting Pressure Test)	-	36000	-
8.4(Test for Safety Pressure Relief Device)	-	36000	-
8.3(Operating Test for Pressure Regulating Device)	-	36000	-
8.2(Proof Pressure Test)	-	36000	-
8.1(Air Pressure Test)	-	36000	-
7.4(WORKMANSHIP AND FINISH)	-	36000	-
7.3(WORKMANSHIP AND FINISH)	-	36000	-
7.2(WORKMANSHIP AND FINISH)	-	36000	-
7.1(WORKMANSHIP AND FINISH)	-	36000	-
6.4.1.1(Handles and Knobs)	-	36000	-
6.4.1(Handles and Knobs)	-	36000	-
6.3.1(Temperature Responsive Pressure Relief Device)	-	36000	-
6.3.1(Temperature Responsive Pressure Relief Device)	-	36000	-
6.2.2(Safety Relief Device)	-	36000	-
6.2.1(Safety Relief Device)	-	36000	-
6.2(Safety Relief Device)	-	36000	-
6.1.5(Pressure Regulating Device)	-	36000	-
6.1.4(Pressure Regulating Device)	-	36000	-
6.1.3(Pressure Regulating Device)	-	36000	-
6.1.2(Pressure Regulating Device)	-	36000	-
6.1.1(Pressure Regulating Device)	-	36000	-
6.1(Pressure Regulating Device)	-	36000	-
6(CONSTRUCTION)	-	36000	-
5.9(Spring)	-	36000	-
5.8(Vent Pipe Nut)	-	36000	-
5.7(Vent Pipe)	-	36000	-
5.6(Vent Seal Pin for Pressure Regulating Device)	-	36000	-
5.5(Pressure Regulating Device)	-	36000	-
5.4(Handles and Knobs)	-	36000	-
5.3(Gasket)	-	36000	-
5.2(Safety Relief Device)	-	36000	-
5.1.4(Body, Lid, Containers and Grid)	-	36000	-
5.1.3(Body, Lid, Containers and Grid)	-	36000	-
5.1.2(Body, Lid, Containers and Grid)	-	36000	-
5.1.1(Body, Lid, Containers and Grid)	-	36000	-
4.1(Capacity )	-	36000	-
8.14(3 Ply Construction Cooker Body)	-	36000	-
8.12(Internal Coating)	-	36000	-
8.11(External Coating )	-	36000	-
8.10 NOTES (6)(Handles of the cooker)	-	36000	-
8.10 NOTES (5)(Handles of the cooker)	-	36000	-
8.10 NOTES (4)(Handles of the cooker)	-	36000	-
8.10 NOTES (3)(Handles of the cooker - Proof Pressure)	-	36000	-
8.10 (f)(Handles of the cooker- Thermal Insualtion Test)	-	36000	-
8.10 (e)(Handles of the cooker- Fatigue Resistance)	-	36000	-
8.10 (d)(Handles of the cooker- Bending Strength)	-	36000	-
8.10 (c)(Handles of the cooker- Torque Strength)	-	36000	-
8.10 (b)(Handles of the cooker- Heat Resistance)	-	36000	-
8.10 (a)(Handles of the cooker- Resistance to Burning)	-	36000	-
8.4(Test for SPRD)	-	36000	-
8.4 Annex H-1.2(Test for SPRD - For Resettable Devices )	-	36000	-
8.4 Annex H-1.1(Test for SPRD - For Destructible Devices )	-	36000	-
6.4.1(Construction - Handles and Knobs)	-	36000	-
6.3(Construction-Temperature Responsive Pressure Relief Device)	-	36000	-
6.2 NOTE(Construction-Safety Relief Device)	-	36000	-
6.1.1(Construction - Pressure Regulating Device)	-	36000	-
8.14(3 Ply Construction Cooker Body)	-	36000	-
8.12.1(Internal Coating)	-	36000	-
8.11.1.1 (Thermal shock test for externally coated cooker)	-	36000	-
8.11.1 (c)(External Coating (powder coating or ceramic coating or high temperature resistant liquid coating))	-	36000	-
8.11.1 (b)(External Coating (powder coating or ceramic coating or high temperature resistant liquid coating))	-	36000	-
8.11.1 (a)(External Coating (powder coating or ceramic coating or high temperature resistant liquid coating))	-	36000	-
8.10 NOTES (6)(Handles of the cooker)	-	36000	-
8.10 NOTES (5)(Handles of the cooker)	-	36000	-
8.10 NOTES (4)(Handles of the cooker)	-	36000	-
8.10 NOTES (3)(Handles of the cooker - Proof Pressure)	-	36000	-
8.10 (f)(Handles of the cooker- Thermal Insualtion Test)	-	36000	-
8.10 (e)(Handles of the cooker- Fatigue Resistance)	-	36000	-
8.10 (d)(Handles of the cooker- Bending Strength)	-	36000	-
8.10 (c)(Handles of the cooker- Torque Strength)	-	36000	-
8.10 (b)(Handles of the cooker- Heat Resistance)	-	36000	-
8.10 (a)(Handles of the cooker- Resistance to Burning)	-	36000	-
8.4(Test for SPRD)	-	36000	-
8.4 Annex H-1.2(Test for SPRD - For Resettable Devices )	-	36000	-
8.4 Annex H-1.1(Test for SPRD - For Destructible Devices )	-	36000	-
6.3.2(The cooker shall satisfy the type test prescribed in Annex D.)	-	36000	-
6.3.1(A separate temperature responsive pressure relief device shall be provided which shall satisfy the test given in Annex C.)	-	36000	-
6.3(Construction-Temperature Responsive Pressure Relief Device)	-	36000	-
6.2(Construction-Safety Relief Device)	-	36000	-
6.1.1(Construction - Pressure Regulating Device)	-	36000	-
5.1(Body, Lid, Containers and Grid)	-	36000	-
5.3(Gasket)	-	36000	-
5.4(Handles and Knobs)	-	36000	-
5.9(Spring)	-	36000	-
8.7(Test for Spring Loaded Mechanism)	-	36000	-
8.8(Test for Spring Loaded Mechanism)	-	36000	-
8.9(Test for Spring Loaded Mechanism)	-	36000	-
11(Marking)	-	36000	-
1()	-	36000	-
6(General Requirements)	-	36000	-
7(Workmanship and Finish)	-	36000	-
9.2(Load Test)	-	36000	-
9.3(Impact Test)	-	36000	-
9.5(Test for Concentricity)	-	36000	-

13 May, 2028

-
Included w.e.f 04.06.2025

IS 2046 (1995)

Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 , Table 1(CLASSIFICATION)	-	24000	-
5.1(Colour and Pattern)	-	24000	-
5.2(Surface Finish)	-	24000	-
5.2.2(Reverse side/Bonding)	-	24000	-
5.3 ,Table 5(Thickness)	-	24000	-
5.4(Appearance )	-	24000	-
5.2.2(Sports, dirt and similar surface defects)	-	24000	-
5.2.2(Fibres,hairs,scratches)	-	24000	-
5.2.2(Accumulated(Combination)of surface defects)	-	24000	-
5.2.2(Edge Defects)	-	24000	-
5.2.2(Broken Corners )	-	24000	-
5.4.4(Sanding Defects)	-	24000	-
5.4.5 table 6(W arping (Flatness ))	-	24000	-
5.4.6 (Length and width of a full size Laminate)	-	24000	-
5.4.6 (Length and width of a full size Laminate)	-	24000	-
5.4.7,Fig. 2(Staightness of Edges)	-	24000	-
5.4.8, Fig.3(Squareness of the Laminates)	-	24000	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	24000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	24000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	24000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	24000	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	24000	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	24000	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	24000	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	24000	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	24000	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	24000	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	24000	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	24000	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	24000	-
5.5, Tables 7, Sr No.(x) Annex -O (alternative)(Resistance to colour change)	-	24000	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	24000	-
5.5, Tables 7, Sr No.(xi) Annex -Q (alternative)(Resistance to Cigarette burns)	-	24000	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	24000	-
5.5, Tables 7, Sr No.(xiv) Annex -R (Formability Method B)	-	24000	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	24000	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method B)	-	24000	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	24000	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	24000	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	24000	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	24000	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	24000	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	24000	-
7.2 a)(Marking)	-	24000	-
7.2 b)(Marking)	-	24000	-
7.2 c)(Marking)	-	24000	-
7.2 d)(Marking)	-	24000	-
7.2.1(Marking)	-	24000	-
5 & 5.1(Colour & Pattern)	-	24000	-
5.2(Surface & Finish)	-	24000	-
5.2.2(Reverse side Bonding)	-	24000	-
5.3(Nominal thickness)	-	24000	-
5.4.1.1(Surface defects)	-	24000	-
5.4.1.2(Fiber hair scratches)	-	24000	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	24000	-
5.4.2(Edge defect)	-	24000	-
5.4.3(Broken corner)	-	24000	-
5.4.4(Sanding defect)	-	24000	-
5.4.5(Warping(Flatness))	-	24000	-
5.4.6(Length)	-	24000	-
5.4.6(Width)	-	24000	-
5.4.7(Straightness of edge)	-	24000	-
5.4.8(Squreness of laminate)	-	24000	-
5.5Table-7(1(Surfacewear)	-	24000	-
Table-7(2(Immesion in boiling water)	-	24000	-
Table-7(3(Dry heat resistance)	-	24000	-
Table-7(4(Dimensional stability)	-	24000	-
Table-7(6(Impact by small dia.Ball)	-	24000	-
Table-7(7(Impact by large dia.Ball)	-	24000	-
Table-7(8(Cracking resistance)	-	24000	-
Table-7(9(Scracting resistance)	-	24000	-
Table-7(10(Staining resistance)	-	24000	-
Table-7(10(Colour change(Xenon arc resis))	-	24000	-
Table-7(11(Cigarette burn resistance)	-	24000	-
Table-7(12(Formability)	-	24000	-
Table-7(13(Blistering)	-	24000	-
Table-7(14(Steam resistance)	-	24000	-
Table-7(15(Crazing reistance)	-	24000	-
Table-7(16(Moisture reistance)	-	24000	-
Table-8(17(Flexural Modulus)	-	24000	-
Table-8(18(Flexural strength)	-	24000	-
Table-8(19(Tensile strength)	-	24000	-
4 , Table 1(CLASSIFICATION)	-	24000	-
5.1(Colour and Pattern)	-	24000	-
5.2(Surface Finish)	-	24000	-
5.2.2(Reverse side/Bonding)	-	24000	-
5.3 ,Table 5(Thickness)	-	24000	-
5.4(Appearance )	-	24000	-
5.2.2(Sports, dirt and similar surface defects)	-	24000	-
5.2.2(Fibres,hairs,scratches)	-	24000	-
5.2.2(Accumulated(Combination)of surface defects)	-	24000	-
5.2.2(Edge Defects)	-	24000	-
5.2.2(Broken Corners )	-	24000	-
5.4.4(Sanding Defects)	-	24000	-
5.4.5 table 6(W arping (Flatness ))	-	24000	-
5.4.6 (Length and width of a full size Laminate)	-	24000	-
5.4.6 (Length and width of a full size Laminate)	-	24000	-
5.4.7,Fig. 2(Staightness of Edges)	-	24000	-
5.4.8, Fig.3(Squareness of the Laminates)	-	24000	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	24000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	24000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	24000	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	24000	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	24000	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	24000	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	24000	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	24000	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	24000	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	24000	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	24000	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	24000	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	24000	-
5.5, Tables 7, Sr No.(x) Annex -O (alternative)(Resistance to colour change)	-	24000	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	24000	-
5.5, Tables 7, Sr No.(xi) Annex -Q (alternative)(Resistance to Cigarette burns)	-	24000	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	24000	-
5.5, Tables 7, Sr No.(xiv) Annex -R (Formability Method B)	-	24000	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	24000	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method B)	-	24000	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	24000	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	24000	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	24000	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	24000	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	24000	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	24000	-
7.2 a)(Marking)	-	24000	-
7.2 b)(Marking)	-	24000	-
7.2 c)(Marking)	-	24000	-
7.2 d)(Marking)	-	24000	-
7.2.1(Marking)	-	24000	-
5 & 5.1(Colour & Pattern)	-	24000	-
5.2(Surface & Finish)	-	24000	-
5.2.2(Reverse side Bonding)	-	24000	-
5.3(Nominal thickness)	-	24000	-
5.4.1.1(Surface defects)	-	24000	-
5.4.1.2(Fiber hair scratches)	-	24000	-
5.4.1.3(Accumulated(combinations) of surface defect)	-	24000	-
5.4.2(Edge defect)	-	24000	-
5.4.3(Broken corner)	-	24000	-
5.4.4(Sanding defect)	-	24000	-
5.4.5(Warping(Flatness))	-	24000	-
5.4.6(Length)	-	24000	-
5.4.6(Width)	-	24000	-
5.4.7(Straightness of edge)	-	24000	-
5.4.8(Squreness of laminate)	-	24000	-
5.5Table-7(1(Surfacewear)	-	24000	-
Table-7(2(Immesion in boiling water)	-	24000	-
Table-7(3(Dry heat resistance)	-	24000	-
Table-7(4(Dimensional stability)	-	24000	-
Table-7(6(Impact by small dia.Ball)	-	24000	-
Table-7(7(Impact by large dia.Ball)	-	24000	-
Table-7(8(Cracking resistance)	-	24000	-
Table-7(9(Scracting resistance)	-	24000	-
Table-7(10(Staining resistance)	-	24000	-
Table-7(10(Colour change(Xenon arc resis))	-	24000	-
Table-7(11(Cigarette burn resistance)	-	24000	-
Table-7(12(Formability)	-	24000	-
Table-7(13(Blistering)	-	24000	-
Table-7(14(Steam resistance)	-	24000	-
Table-7(15(Crazing reistance)	-	24000	-
Table-7(16(Moisture reistance)	-	24000	-
Table-8(17(Flexural Modulus)	-	24000	-
Table-8(18(Flexural strength)	-	24000	-
Table-8(19(Tensile strength)	-	24000	-

13 May, 2028

-
Included w.e.f.06.02.2025

IS 6528 (2024)

Stainless steel wire - Specification ( Second Revision )

All

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 6(FREEDOM FROM DEFECTS)	-	17000	-
As per clause 7(CARBON)	-	17000	-
As per clause 7(SILICON)	-	17000	-
As per clause 7(MANGANESE)	-	17000	-
As per clause 7(PHOSPHORUS)	-	17000	-
As per clause 7(SULPHUR)	-	17000	-
As per clause 7(CHROMIUM)	-	17000	-
As per clause 7(MOLYBEDNUM)	-	17000	-
As per clause 7(NICKEL)	-	17000	-
As per clause 7(NITROGEN)	-	17000	-
As per clause 7(COPPER)	-	17000	-
As per clause 7(NIOBIUM)	-	17000	-
As per clause 7(TITANIUM)	-	17000	-
As per clause 7(ALUMINIUM)	-	17000	-
As per clause 8(HEAT TREATMENT)	-	17000	-
As per clause 9(Dimension Tolerance)	-	17000	-
As per clause 10(TENSILE TEST)	-	17000	-
As per clause 10.2(REVERSE BEND TEST)	-	17000	-
As per clause 10.3(TORSION TEST)	-	17000	-
As per clause 14(FINISH)	-	17000	-
As per clause 15(CORROSION RESISTANCE)	-	17000	-
As per clause 16.2(MARKING)	-	17000	-
As per Clause 6(FREEDOM FROM DEFECTS)	-	17000	-
As per clause 7(CARBON)	-	17000	-
As per clause 7(SILICON)	-	17000	-
As per clause 7(MANGANESE)	-	17000	-
As per clause 7(PHOSPHORUS)	-	17000	-
As per clause 7(SULPHUR)	-	17000	-
As per clause 7(CHROMIUM)	-	17000	-
As per clause 7(MOLYBEDNUM)	-	17000	-
As per clause 7(NICKEL)	-	17000	-
As per clause 7(NITROGEN)	-	17000	-
As per clause 7(COPPER)	-	17000	-
As per clause 7(NIOBIUM)	-	17000	-
As per clause 7(TITANIUM)	-	17000	-
As per clause 7(ALUMINIUM)	-	17000	-
As per clause 8(HEAT TREATMENT)	-	17000	-
As per clause 9(Dimension Tolerance)	-	17000	-
As per clause 10(TENSILE TEST)	-	17000	-
As per clause 10.2(REVERSE BEND TEST)	-	17000	-
As per clause 10.3(TORSION TEST)	-	17000	-
As per clause 14(FINISH)	-	17000	-
As per clause 15(CORROSION RESISTANCE)	-	17000	-
As per clause 16.2(MARKING)	-	17000	-

13 May, 2028

-
Included w.e.f.02.06.2025

IS 13395 (2021)

Performance of Handles and Handle Assemblies Attached to Cookware - Specification ( First Revision )

ALL

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1()	-	10000	-
4.1(Construction)	-	10000	-
4.2(Materials)	-	10000	-
4.3(Selection and Size)	-	10000	-
4.4(Position of handle and knob with respect to cookware)	-	10000	-
4.()	-	10000	-
4.5(Attachment to cookware)	-	10000	-
4.()	-	10000	-
5.1(General)	-	10000	-
5.2(Bending strength)	-	10000	-
5.3(Torque strength)	-	10000	-
5.4(Impact strength)	-	10000	-
5.5(Fatigue resistance)	-	10000	-
5.6(Leakage)	-	10000	-
5.7(Thermal insulation)	-	10000	-
5.8(Heat resistance)	-	10000	-
5.9(Washing resistance)	-	10000	-
5.10(Burning resistance)	-	10000	-

13 May, 2028

-
Included w.e.f.30.05.2025

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

All

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	20000	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	20000	-
11(Transverse Tension Test,%)	-	20000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	20000	-
13 (Table No.- 7)(Flaring Test)	-	20000	-
14(Flattaning Test-IS 2328)	-	20000	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	20000	-
17(Leak Tighteness Test)	-	20000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	20000	-
19(Eddy current test & Air under water)	-	20000	-
21(Workmanship, Finish and Appearance)	-	20000	-
22(Repair by Welding or Grinding)	-	20000	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	20000	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	20000	-
Clause 10.1 - Table 4(Tensile Strength)	-	20000	-
Clause 10.1 - Table 4(Percent Elongation)	-	20000	-
Clause 11(Transverse Tension Test)	-	20000	-
Clause 12(Hardness Test)	-	20000	-
Clause 13(Flaring Test)	-	20000	-
Clause 14(Flattening Test)	-	20000	-
Clause 15(Grain Size)	-	20000	-
Clause 17(Leak Tightness Test)	-	20000	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	20000	-
Clause 21(Workmanship, Finish & Appearance)	-	20000	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	20000	-
10.2(Hardness test IS 1500 (part-1):2019)	-	20000	-
12.2(Flaring test IS 17878:2022)	-	20000	-
16(Sampling)	-	20000	-
24(Marking)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	20000	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	20000	-
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	20000	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	20000	-
11(Transverse Tension Test,%)	-	20000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	20000	-
13 (Table No.- 7)(Flaring Test)	-	20000	-
14(Flattaning Test-IS 2328)	-	20000	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	20000	-
17(Leak Tighteness Test)	-	20000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	20000	-
19(Eddy current test & Air under water)	-	20000	-
21(Workmanship, Finish and Appearance)	-	20000	-
22(Repair by Welding or Grinding)	-	20000	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	20000	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	20000	-
Clause 10.1 - Table 4(Tensile Strength)	-	20000	-
Clause 10.1 - Table 4(Percent Elongation)	-	20000	-
Clause 11(Transverse Tension Test)	-	20000	-
Clause 12(Hardness Test)	-	20000	-
Clause 13(Flaring Test)	-	20000	-
Clause 14(Flattening Test)	-	20000	-
Clause 15(Grain Size)	-	20000	-
Clause 17(Leak Tightness Test)	-	20000	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	20000	-
Clause 21(Workmanship, Finish & Appearance)	-	20000	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	20000	-
10.2(Hardness test IS 1500 (part-1):2019)	-	20000	-
12.2(Flaring test IS 17878:2022)	-	20000	-
16(Sampling)	-	20000	-
24(Marking)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	20000	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	20000	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	20000	-

13 May, 2028

-
Included w.e.f.02.06.2025

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

ALL

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Others-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl. 7.1 & 7.2 Table 1(Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	17000	-
Cl.12(Corrosion Resistance- IS 10461(Part1))	-	17000	-
Cl.12(Corrosion Resistance- IS 10461(Part2))	-	17000	-
6(Freedom from defects , IS 6911)	-	17000	-
10.1,Table 4&Table 6(Tensile Test - IS 1608(Pt -1))	-	17000	-
10.2,Table 4&Table 5(Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-	17000	-
10.3(Bend Test - IS 1599)	-	17000	-
11,Table 7(Erichsen cupping test-IS 10175)	-	17000	-
15(Surface Finish)	-	17000	-
17(Dimension and tolerance)	-	17000	-
10.1 Amd 2(Yeild Strength)	-	17000	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	17000	-
10.1 Amd 2(Elongation)	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	17000	-
Clause 17 , Table 9 to Table 19(Flatness)	-	17000	-
Clause 17 , Table 9 to Table 19(Camber)	-	17000	-
Table 1(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
10.1 Amd 2(Yeild Strength)	-	17000	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	17000	-
10.1 Amd 2(Elongation)	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	17000	-
Clause 17 , Table 9 to Table 19(Flatness)	-	17000	-
Clause 17 , Table 9 to Table 19(Camber)	-	17000	-
Table 1(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
10.1 Amd 2(Yeild Strength)	-	17000	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	17000	-
10.1 Amd 2(Elongation)	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	17000	-
10.1 Amd 2(Yeild Strength)	-	17000	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	17000	-
10.1 Amd 2(Yeild Strength)	-	17000	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	17000	-
10.1 Amd 2(Elongation)	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	17000	-
Clause 17 , Table 9 to Table 19(Flatness)	-	17000	-
Clause 17 , Table 9 to Table 19(Camber)	-	17000	-
Table 1(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
Table 1, Amendment 2(Any Instrumental Method/Chemical Method)	-	17000	-
4(Supply of Material)	-	17000	-
8(Heat Treatment)	-	17000	-
19(Marking)	-	17000	-
5(Manufacture)	-	17000	-
10.1 Amd 2(Yeild Strength)	-	17000	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	17000	-
10.1 Amd 2(Elongation)	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	17000	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	17000	-
Clause 17 , Table 9 to Table 19(Flatness)	-	17000	-
Clause 17 , Table 9 to Table 19(Camber)	-	17000	-
Table 1(Alumium)	-	17000	-
Table 1, Amendment 2(Zirconium)	-	17000	-
Table 1, Amendment 2(Tungstun)	-	17000	-
Table 1, Amendment 2(Tungstun)	-	17000	-
Table 1, Amendment 2(Ce)	-	17000	-
Table 1, Amendment 2(Cobalt)	-	17000	-
Table 1, Amendment 2(Ta)	-	17000	-
5.1 - 1(Carbon)	-	17000	-
5.1 - 1(Sulphur)	-	17000	-
5.1 - 1(Phosphorus)	-	17000	-
5.1 - 1(Manganese)	-	17000	-
5.1 - 1(Silicon)	-	17000	-
5.1 - 1(Nitrogen)	-	17000	-
5.1 - 1(Copper)	-	17000	-
5.1 - 1(Titanium)	-	17000	-
5.1 - 1(Aluminium)	-	17000	-
5.1 - 1(Niobium)	-	17000	-
5.1 - 1(Nickel)	-	17000	-
5.1 - 1(Chromium)	-	17000	-
5.1 - 1(Molybdenum)	-	17000	-
6(Freedom from defect)	-	17000	-
10.1 - 4(Tensile Test)	-	17000	-
10.1 - 4(Yield strength)	-	17000	-
10.1 - 4(Elongation % on 50mm)	-	17000	-
10.2(Hardness Test)	-	17000	-
10.3(Bend Test)	-	17000	-
11(Erichsen Cupping Test)	-	17000	-
17(Dimension and tolerance)	-	17000	-
12(Corrosion resistance)	-	17000	-
5.1 - 1(Carbon)	-	17000	-
5.1 - 1(Sulphur)	-	17000	-
5.1 - 1(Phosphorus)	-	17000	-
5.1 - 1(Manganese)	-	17000	-
5.1 - 1(Silicon)	-	17000	-
5.1 - 1(Nitrogen)	-	17000	-
5.1 - 1(Copper)	-	17000	-
5.1 - 1(Titanium)	-	17000	-
5.1 - 1(Aluminium)	-	17000	-
5.1 - 1(Niobium)	-	17000	-
5.1 - 1(Nickel)	-	17000	-
5.1 - 1(Chromium)	-	17000	-
5.1 - 1(Molybdenum)	-	17000	-
6(Freedom from defect)	-	17000	-
10.1 - 4(Tensile Test)	-	17000	-
10.1 - 4(Yield strength)	-	17000	-
10.1 - 4(Elongation % on 50mm)	-	17000	-
10.2(Hardness Test)	-	17000	-
10.3(Bend Test)	-	17000	-
11(Erichsen Cupping Test)	-	17000	-
17(Dimension and tolerance)	-	17000	-
12(Corrosion resistance)	-	17000	-

13 May, 2028

-
Included w.e.f.30.05.2025

IS 6603 (2024)

Stainless Steel Semi-Finished Products, Bars, Wire Rods and Bright Bars â Specification (Second Revision)

ALL

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl - 9.1,9.5,13.2(Thickness or Diameter)	-	270	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 0.2 MP)	-	270	-
Cl - 9.1,9.5,13.2(Proof Strength Rp 1.0 MP)	-	270	-
Cl - 9.1,9.5,13.2(Tensile Strength)	-	270	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Long.)	-	270	-
Cl - 9.1,9.5,13.2(Elongation After Fracture Tr.)	-	270	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Long.)	-	270	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V) Tr.)	-	270	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Delivery Condition)	-	270	-
Cl - 9.1,9.5,13.2(Resistance to Inter-Granular Corrosion in the Sensitized Condition)	-	270	-
Cl - 9.1,9.5,13.2(Hardness)	-	270	-
Cl - 9.1,9.5,13.2(Elongation After Fracture)	-	270	-
Cl - 9.1,9.5,13.2(Impact Energy (ISO-V))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(Thickness or Diameter)	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(R MPa Max(Annealed))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(Hardness HB Max(Annealed))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(Heat Treatment Condition (Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(R 0.2 MPa Min(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(R Mpa(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Long.(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(A Percent Min Tr.(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	270	-
Cl - 9.1,9.3,9.4,9.5,13.2(KV J Min Long.(Quenched + Tempered))	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 450 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 500 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 550 Deg. C)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 100 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 150 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 200 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 250 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 300 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 350 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 400 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 450 Deg. C.)	-	270	-
Cl - 9.2(Minimum 1 Percent Proof Strength at 550 Deg. C.)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 300 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 350 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 400 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 100 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 150 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 200 Deg. C)	-	270	-
Cl - 9.2(Minimum 0.2 Percent Proof Strength at 250 Deg. C)	-	270	-
Cl-7.1, 7.2(C)	-	270	-
Cl-7.1, 7.2(Si)	-	270	-
Cl-7.1, 7.2(Mn)	-	270	-
Cl-7.1, 7.2(P)	-	270	-
Cl-7.1, 7.2(S)	-	270	-
Cl-7.1, 7.2(Cr)	-	270	-
Cl-7.1, 7.2(Mo)	-	270	-
Cl-7.1, 7.2(Ni)	-	270	-
Cl-7.1, 7.2(N)	-	270	-
Cl-7.1, 7.2(Cu)	-	270	-
Cl-7.1, 7.2(Ti)	-	270	-
Cl-7.1, 7.2(W)	-	270	-
Cl-7.1, 7.2(Nb)	-	270	-
cL-7.1, 7.2(Co)	-	270	-
Cl-7.1, 7.2(Ti: (C + N))	-	270	-
Cl-7.1, 7.2(V)	-	270	-
Cl-7.1, 7.2(Al)	-	270	-
Cl-7.1, 7.2(Boron)	-	270	-
Cl-7.1, 7.2(Tungsten)	-	270	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1((Titanium- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.))	-	270	-
Cl 6((freedom from defects))	-	270	-
Cl. 12((dimension and tolerance))	-	270	-
Cl. 14((corrosion resistance))	-	270	-

13 May, 2028

-
Included w.e.f.30.05.2025

IS 17526 (2021)

STAINLESS STEEL VACUUM FLASKS - SPECIFICATION

ALL TYPES

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Manufacture and Workmanship)	-	26000	-
5.3(Manufacture and Workmanship)	-	26000	-
7.1.1(Material- Inner containers)	-	26000	-
7.1.2(Outer protective case and accessories - Thickness)	-	26000	-
7.1.2.1(Coating - Limit of lead)	-	26000	-
7.1.2.1(Coating - Limit of Cadmium)	-	26000	-
7.1.4(Auxillary closure "Bisphenol A (BPA)")	-	26000	-
7.3(Capacity)	-	26000	-
7.4(Heat Retention Capability)	-	26000	-
7.5(Cold Retention Capability)	-	26000	-
7.6.1(Drop Impact Test)	-	26000	-
7.6.2(Pendulum Impact Test)	-	26000	-
7.7(Fixing Strength of the Handle)	-	26000	-
7.8(Test for Strength of Shoulder Strap)	-	26000	-
7.8.1(Test for strength of cord)	-	26000	-
7.9(Leakage Test)	-	26000	-
7.10(Joint Leak Test)	-	26000	-
7.11(Staining Test)	-	26000	-
7.12(Length of the Shoulder Strap)	-	26000	-
7.13(Stability of Flask/Bottle)	-	26000	-
7.14(Pour Test)	-	26000	-
9.1(Marking)	-	26000	-
9.2(BIS certification marking)	-	26000	-
10(Packaging)	-	26000	-
7.1.2(Outer protective case and accessories - Material)	-	26000	-
7.1.2.1(Coating- Thickness test)	-	26000	-
7.1.2.1(Coating- Adhesion test)	-	26000	-
7.1.2.1(Coating- Salt Water corrosion test)	-	26000	-
7.2(Arrangement for holding and suspension)	-	26000	-
7.15 (Amendment 1)(Endurance test for O-Ring, Washer and Stopper)	-	26000	-
7.1.3(Overall migration)	-	26000	-
7.1.3 (Amendment 1)(O-Ring and washer- Hardness)	-	26000	-
7.1.3 (Amendment 1)(O-Ring and washer-- BPA)	-	26000	-
7.1.3(Stopper Material)	-	26000	-

13 May, 2028

-
Included w.e.f. 03.06.2025

IS 15960 (2013)

Composite bottom stainless steel cooking utensils - Specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material - manufacture of utensils)	-	15000	-
3.1.1.1(Material - electrolytic copper)	-	15000	-
3.1.1.2(Material - copper cladding)	-	15000	-
3.1.1.3(Material – aluminium cladding)	-	15000	-
3.1.2(Material - protector plate)	-	15000	-
3.1.2.1(Material – copper core)	-	15000	-
3.1.2.2(Material – aluminium core)	-	15000	-
3.2(Material – Rivets, legs and other fittings)	-	15000	-
3.3(Material – screw)	-	15000	-
3.4(Material – handle and knob)	-	15000	-
3.5(Material – corrosion Resisting/ non-ferrous/ plastic)	-	15000	-
4(Material Thickness)	-	15000	-
5(Dimensions of Utensil)	-	15000	-
6(Workmanship)	-	15000	-
7.1(Tests - Coating Thickness Test)	-	15000	-
7.2 & 7.2.1(Tests - Adhesion Test - Mechanical Shock Test)	-	15000	-
7.2.2(Tests - Thermal Shock Test)	-	15000	-
7.2.3(Tests - Dry Heat Test)	-	15000	-
7.3(Staining Test)	-	15000	-
10(Marking)	-	15000	-

13 May, 2028

-
Included. w.e.f.03.06.2025

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

26000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	26000	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	26000	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	26000	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	26000	-
Cl-4.1(Main body of utensil)	-	26000	-
Cl-4.1(Cast cookware)	-	26000	-
Cl-4.1(Other aluminum components and parts)	-	26000	-
Cl-4.1.1(Lids (material))	-	26000	-
Cl-4.1.1(Minimum thickness of lid)	-	26000	-
Cl-4.1.2(Minimum thickness of glass)	-	26000	-
Cl-4.1.2(Material of rim)	-	26000	-
Cl-4.1.2(Minimum thickness of rim)	-	26000	-
Cl-4.2(Material of strips)	-	26000	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	26000	-
Cl-4.3(Clips of lunch box)	-	26000	-
Cl-4.3(Clips of lunch box)	-	26000	-
Cl-4.3(Rivets used in lunch box)	-	26000	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	26000	-
Cl-4.5(Rivets for fixing of handles)	-	26000	-
Cl-4.5(Material of cap)	-	26000	-
Cl-4.6(Strips used for flame guards)	-	26000	-
Cl-4.6(stainless steel)	-	26000	-
Cl-5(Fabrication)	-	26000	-
Cl-6(Shape and Dimensions)	-	26000	-
Cl-7.1(Handles, when fitted)	-	26000	-
Cl-7.2(Handles)	-	26000	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	26000	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	26000	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	26000	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	26000	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	26000	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	26000	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	26000	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	26000	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	26000	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	26000	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	26000	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	26000	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	26000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	26000	-
Cl-8(Workmanship and Finish)	-	26000	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	26000	-
Cl-8.3(Minimum nominal thickness)	-	26000	-
Cl-8.3(Thickness of hard anodized)	-	26000	-
Cl-8.3(Finish and appearance of hard anodized)	-	26000	-
Cl-8.3(Abrasion resistance of hard anodized)	-	26000	-
Cl-8.3(Colour of hard anodized)	-	26000	-
Cl-8.3(Hardness of hard anodized)	-	26000	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	26000	-
Cl-8.5(Non-stick unreinforced PTFE)	-	26000	-
Cl-8.6(Ceramic coating)	-	26000	-
Cl-8.7(The thickness test, adhesion test)	-	26000	-
Cl-8.7(Minimum thickness of coating)	-	26000	-
Cl-8.7.1(Dry heat the cookware)	-	26000	-
Cl-8.8(Requirements of PTFE)	-	26000	-
Cl-8.9(Material for induction plate)	-	26000	-
Cl-8.9(Test for Induction compatible base)	-	26000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	26000	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	26000	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	26000	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	26000	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	26000	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	26000	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	26000	-
Cl-9.1(Normal Capacity)	-	26000	-
Cl-9.2(Normal Capacity of internal diameter)	-	26000	-

13 May, 2028

-
Included w.e.f.03.06.2025

IS 9730 (2008)

Non - Stick unreinforced plastics coatings on domestic cooking utensils - Specification (First Revision)

ALL TYPES

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	4000	-
4.2(Visual Defects)	-	4000	-
4.3 & 7.2(Thickness)	-	4000	-
4.4 & 7.3(Non-stick Quality)	-	4000	-
4.5 & 7.4(Salt Water Corrosion Resistance)	-	4000	-
4.6, 7.5.2 & 7.5.3(Adhesion Test)	-	4000	-
5(Marking)	-	4000	-
6(Instructions for use)	-	4000	-

13 May, 2028

-
Included w.e.f 19.05.2025

IS 17803 (2022)

POTABLE WATER BOTTLES (COPPER, STAINLESS STEEL, ALUMINIUM) SPECIFICATION

ALL TYPES

29000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Manufacture and Workmanship)	-	29000	-
5.3(Manufacture and Workmanship)	-	29000	-
7.1(Materials)	-	29000	-
7.1.1(copper bottle - copper)	-	29000	-
7.1.1(copper bottle – lead)	-	29000	-
7.1.1(copper bottle – bismuth)	-	29000	-
7.1.1(copper bottle – oxygen)	-	29000	-
7.1.1(copper bottle – total impurities)	-	29000	-
7.1.3.3(o-ring or washer - Defects)	-	29000	-
7.1.4(Auxillary closure- Bisphenol A (BPA))	-	29000	-
7.1.8(Anodic coating)	-	29000	-
7.1.8(Hard Anodized)	-	29000	-
7.1.9(External coating– Limit of Lead)	-	29000	-
7.1.9(External coating– Limit of Cadmium)	-	29000	-
7.2(Capacity)	-	29000	-
7.3, 7.3.1, 7.3.2(Impact resistance Test/ Drop Impact Test/ Pendulum Impact test)	-	29000	-
7.4(Test for strength of shoulder strap)	-	29000	-
7.5(Test for cord)	-	29000	-
7.7(Leakage test)	-	29000	-
7.8(Staining test)	-	29000	-
7.9(Lever, device for operating or Regulating flow test)	-	29000	-
7.10(Stability test)	-	29000	-
7.11(Load test)	-	29000	-
7.12(Food safe test/Leaching test)	-	29000	-
7.12(Water potability)	-	29000	-
7.13(Turbidity)	-	29000	-
7.13(pH value)	-	29000	-
7.13(Taste threshold)	-	29000	-
7.13(Colour, Hazen units)	-	29000	-
7.13(Odour)	-	29000	-
7.13(Total dissolved solids)	-	29000	-
9.1(Marking)	-	29000	-
7.1.3(Overall Migration test (IS 9845 : 1998))	-	29000	-
Cl. 7.1.5(PERFORMANCE TEST (Lever device ))	-	29000	-
7.1.1.1(copper bottle – Thickness)	-	29000	-
7.1.2.1(Stainless steel bottle (thickness))	-	29000	-
7.1.2.1(Stainless steel bottle (material))	-	29000	-
7.1.2 Note 2(Aluminium bottle (Material))	-	29000	-
7.1.3.1(Stopper Material)	-	29000	-
7.1.3.2(o-ring or washer Overall migration)	-	29000	-
7.1.4(Auxillary closure - Material)	-	29000	-
7.1.9(External coating - Thickness test)	-	29000	-
7.1.9(External coating - Salt water corrosion test)	-	29000	-
7.1.9(External coating - Adhesion test)	-	29000	-
7.3.1.3 (Amendment 1)(Drop impact test - Free fall test)	-	29000	-
7.3.1.2 (Amendment 1)(Drop impact test - Vertical hang)	-	29000	-
7.3.1.1 (Amendment 1)(Drop impact test - Horizontal Hang)	-	29000	-
Cl 7.6(Test for cord chain)	-	29000	-
7.1.2 (Note 1), Annex B (Amendment 1)- Sensorial test(Annex B (Amendment 1)- Sensorial test)	-	29000	-
15. 7.1.2 (Note 1), Annex A (Amendment 1)- Leaching of food grade stainless steel(Annex A (Amendment 1)- Leaching of food grade stainless steel)	-	29000	-

13 May, 2028

-
Included w.e.f 19.05.2025

IS 14756 (2024)

Stainless Steel Utensils - Specification (THIRD REVISION)

ALL TYPES

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Material used for manufacturing utensils)	-	30000	-
Cl 3.2(Material used for composite bottom)	-	30000	-
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	30000	-
Cl 3.4(Material used for stainless steel lid)	-	30000	-
Cl 3.5(Material used for tempered glass lid)	-	30000	-
Cl 3.5(Material used for stainless steel rim)	-	30000	-
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	30000	-
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	30000	-
Cl 4.2(Thickness of the finished utensil)	-	29999.98	-
Cl 4.3(Classification)	-	30000	-
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	30000	-
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	30000	-
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	30000	-
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	30000	-
Cl 5.1(Manufacturing defect & visual appearance)	-	30000	-
CL 5.2(Accessibility for cleaning)	-	30000	-
Cl 5.3(Joining of handles to the utensils)	-	30000	-
Cl 5.4(Requirement for handles)	-	30000	-
Cl 5.5(Welding (Finish))	-	30000	-
Cl 5.6(Finish of 3-ply utensil)	-	30000	-
Cl 5.7(Requirement for coating)	-	30000	-
Cl 5.8(Coating thickness test)	-	30000	-
Cl 5.8(Coating adhesion test)	-	30000	-
Cl 5.8.1(Thermal shock test (Coating))	-	30000	-
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	30000	-
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	30000	-
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	30000	-
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	30000	-
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	30000	-
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	30000	-
Cl 6.7(Nominal Capacity Test)	-	30000	-
Cl 8(Marking)	-	30000	-
3.1(a) Carbon)	-	30000	-
3.1(b) Silicon)	-	30000	-
3.1(c)Manganese)	-	30000	-
3.1(d) Nickel)	-	30000	-
3.1(Chromium)	-	30000	-
3.1(Sulphu)	-	30000	-
3.1(Phosphorus)	-	30000	-
Stainless Steel Utensils - Specification (THIRD REVISION)(Copper)	-	30000	-
3.1(Nitrogen)	-	30000	-
3.2 a(a) Carbon)	-	30000	-
3.2 a(b) Silicon)	-	30000	-
68995(Manganese)	-	30000	-
3.2 a(d) Nickel)	-	30000	-
3.2 a(Chromium)	-	30000	-
3.2 a(Sulphur)	-	30000	-
3.2 a(g) Phosphorus)	-	30000	-
3.2 a(h) Copper)	-	30000	-
3.2 a(Nitrogen)	-	30000	-
3.2 b(a) Aluminium)	-	30000	-
3.2 b(b) Copper)	-	30000	-
3.2 b(c) Magnesium)	-	30000	-
3.2 b(d) Silicon)	-	30000	-
3.2 b(e) Iron)	-	30000	-
3.2 b(f) Manganese)	-	30000	-
3.2 b(d) Silicon)	-	30000	-
3.2 b(e) Iron)	-	30000	-
3.2 b(f) Manganese)	-	30000	-
3.2 b(g) Zinc)	-	30000	-
3.2 b(h) Titanium)	-	30000	-
3.2 b(i) Chromium)	-	30000	-
3.2 b(j) Cu+Si+Fe+Mn+Zn+mg)	-	30000	-
3.2 b(k) Lead)	-	30000	-
3.2 c(a) Carbon)	-	30000	-
3.2 c(b) Silicon)	-	30000	-
3.2 c(c) Manganese)	-	30000	-
3.2 c(d) Nickel)	-	30000	-
3.2 c(e) Chromium)	-	30000	-
3.2 c(f) Sulphur)	-	30000	-
3.2 c(g) Phosphorus)	-	30000	-
3.3(a) Inner layer)	-	30000	-
3.3(b) Middlelayer)	-	30000	-
3.3(c) Outerlayer)	-	30000	-
3.4(a) Carbon)	-	30000	-
3.4(b) Silicon)	-	30000	-
3.4(c) Manganese)	-	30000	-
3.4(d) Nickel)	-	30000	-
3.4(e) Chromium)	-	30000	-
3.4(f) Sulphur)	-	30000	-
3.4(g) Phosphorus)	-	30000	-
3.4(h) Copper)	-	30000	-
3.4(i) Nitrogen)	-	30000	-
3.4(Thickness stainless steel lid)	-	30000	-
3.5(If the utensils provided with tempered glass lid)	-	30000	-
4.1(Shapes and Dimensions)	-	30000	-
4.2(Thickness of the sheet)	-	30000	-
4.3(Classifications)	-	30000	-
4.3(Core Thickness for 3-ply Construction (asper IS15960))	-	30000	-
4.3(Thickness of protective layer (as per IS 15960))	-	30000	-
4.4(Thickness of 3ply full body utensil)	-	30000	-
5(Workmanship and finish)	-	30000	-
5.4(Handles)	-	30000	-
4.1 of IS 13395(Construction)	-	30000	-
4.2 of IS 13395(Materials)	-	30000	-
4.3 of IS 13395(Selection and Size)	-	30000	-
4.4 of Is 13395(Position of Handle and Knob with Respect to Cookware)	-	30000	-
4.5 of IS 13395(Attachment to Cookware)	-	30000	-
5.2 of IS 13395(Bending Strength)	-	30000	-
5.3 of IS 13395(Torque Strength)	-	30000	-
5.4 of IS 13395(Impact Strength)	-	30000	-
5.5 of IS 13395(Fatigue Resistance 15 000 cycles withstand)	-	30000	-
5.6 of IS 13395(Leakage)	-	30000	-
5.7 of IS 13395(Thermal Insulation)	-	30000	-
5.8 of IS 13395(Heat Resistance)	-	30000	-
5.9 of IS 13395(Washing Resistance)	-	30000	-
5.10 of IS 13395(Burning Resistance)	-	30000	-
5.5(Material comes in contact with food)	-	30000	-
6.1(Staining Test)	-	30000	-
6.2(Mechanical Shock Test)	-	30000	-
6.3(Thermal Shock Test)	-	30000	-
6.4(Dry Heat Test)	-	30000	-
6.6(Heat test)	-	30000	-
6.7.1(Nominal Capacity Test)	-	30000	-
6.7.2(Internal diameter of utensil)	-	30000	-

13 May, 2028

-
Included w.e.f 19.05.2025

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

All Grades/Types

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Freedom from Defects)	-	8000	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	8000	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	8000	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	8000	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	8000	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	8000	-
7(Dimension - IS 3965)	-	8000	-
11(Marking)	-	8000	-
Table-1, Clause - 5.1(Copper)	-	8000	-
Table-1, Clause - 5.1(Iron)	-	8000	-
Table-1, Clause - 5.1(Magnesium)	-	8000	-
Table-1, Clause - 5.1(Manganese)	-	8000	-
Table-1, Clause - 5.1(Titanium)	-	8000	-
Table-1, Clause - 5.1(Silicon)	-	8000	-
Table-1, Clause - 5.1(Chromium)	-	8000	-
Table-1, Clause - 5.1(Zinc)	-	8000	-

13 May, 2028

-
-

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

All Grades/Types

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 1(chemical composition)	-	15000	-
5.1 table 2(0.2% proof strength)	-	15000	-
5.1 table 2(Tensile strength)	-	15000	-
5.1 table 2(Elongation)	-	15000	-
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	15000	-
4.1(Freedom from defects)	-	15000	-
9.1(Tensile test)	-	15000	-

13 May, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

SHRI KRISHNA TEST HOUSE PVT LTD (142)

Plot No.142, Sec-G, Bawana-II, DSIIDC, Bhorgarh industrial area New Delhi, Delhi, North, Delhi, 110040

9266808773 SKTHPL142@GMAIL.COM

Scope List