BIS - LIMS (Laboratory Information Management System)

Kailtech Test and Research Centre Pvt. Ltd., Indore

141C, Electronic Complex Industrial Area, Indore, Indore, Madhya Pradesh, 452010

- contact@kailtech.net

Scope List

Reset

130 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 2385 (1977)

Specification for hot - Rolled mild steel sheet and strip in coil form for cold - Reduced tinplate and cold - Reduced blackplate (First Revision)

All

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1, 5.2 & Table1(Carbon- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	2000	-
Cl. 5.1, 5.2 & Table1(Manganese- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	1500	-
Cl. 5.1, 5.2 & Table1(Sulphur- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	1500	-
Cl. 5.1, 5.2 & Table1(Phosphorus- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	1500	-
Cl. 5.1, 5.2 & Table1(Nitrogen- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	2000	-
Cl. 5.1, 5.2 & Table1(Aluminium- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	1500	-
6(Freedom from defects)	-	1000	-
8(Dimensions and Tolerances)	-	500	-
Cl. 5.1, 5.2(chromium)	-	1500	-
Cl. 5.1, 5.2(silicon)	-	1500	-
Cl. 5.1, 5.2(copper)	-	1500	-
Cl. 5.1, 5.2(aluminium)	-	0	-
Cl. 5.1, 5.2(Nitrogen )	-	0	-
Cl. 5.1, 5.2(Phosphorus)	-	0	-
Cl. 5.1, 5.2(Sulphur)	-	0	-
Cl. 5.1, 5.2(Manganese)	-	0	-
Cl. 5.1, 5.2(carbon)	-	0	-

18 Dec, 2027

-
Included w.e.f 10.10.2024

122

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Sulphur -IS 228 or method specified in relevant ISO standard)	-	3000	-
Cl.4(Phosphorus -IS 228 or method specified in relevant ISO standard)	-	3000	-
5.2(Tensile Test-1608:Part 1)	-	4000	-
5.2(Tensile Strength, Mpa)	-	2000	Elongation
5.2(Elongation, %)	-	2000	-
5.3(Bend Test-1599)	-	1000	-
7.1(Freedom from defects)	-	1000	-
8.2(Width)	-	1000	-
8.2(Thickness)	-	1000	-
9.1(Finishing & Packing)	-	0	-
10(Marking)	-	0	-
Cl.4(Sulphur -IS 228 or method specified in relevant ISO standard)	-	0	-
Cl.4(Phosphorus -IS 228 or method specified in relevant ISO standard)	-	0	-
5.2(Tensile Test-1608:Part 1)	-	0	-
5.2(Tensile Strength, Mpa)	-	0	-
5.2(Elongation, %)	-	0	-
5.3(Bend Test-1599)	-	0	-
7.1(Freedom from defects)	-	0	-
8.2(Width)	-	0	-
8.2(Thickness)	-	0	-
9.1(Finishing & Packing)	-	0	-
10(Marking)	-	0	-

18 Dec, 2027

-
Included w.e.f 10.10.2024

123

IS 18385 (2023)

Hot- Dip galvanized/galvannealed Steels Sheet and strips for Automotive Applications- Specification

All

28500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.5(Surface Finish)	-	2500	Chemical Mapping not available
Clause. 5.0(Material)	-	0	-
Clause. 8.0(Tensile Test)	-	2000	-
Clause. 8.0(Yield Stress or Proof stress)	-	2000	-
Clause. 8.0(Elongation)	-	1000	-
Clause. 8.0(Plastic strain Ratio)	-	1500	-
Clause. 8.0(Tensile Strain Hardening Component)	-	1500	-
Clause. 8.0(Bake Hardening Index)	-	2000	-
Clause. 8.0(Hole Expansion Ratio)	-	2000	-
Clause. 8.0(Bend Test)	-	1000	-
Clause.9.0(Coating Mass)	-	2000	-
Clause.9.0(Coating Adherence)	-	1000	-
Clause.10.0(Dimensions, Shape & Tolerances)	-	8000	-
Clause.19.0(Mass)	-	1000	-
Clause.11.0(Freedom From Defects)	-	1000	-

18 Dec, 2027

-
Included w.e.f 21.10.2024

124

IS 14246 (2024)

CONTINUOUSLY PRE-PAINTED GALVANIZED STEEL SHEETS AND STRIPS - SPECIFICATION Second Revision

All

30000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Steel Base)	-	5000	Rs.30000/- for Class 1, Rs.35000/- for Class 2, Rs.45,000/- for Class 3, Rs.60000/- for Class 4.
Cl-4.2(Metallic Coating)	-	2000	-
Cl-4.5(Profiles)	-	0	-
Cl-5(Classification of durability of organic coating)	-	0	-
Cl-6.1(Sampling of Test Specimen)	-	0	-
Cl-6.2.3(Bend Test)	-	1000	-
Cl-6.3.1(Pencil Hardness Test)	-	1000	-
Cl-6.4(Impact Resistance Test)	-	1000	-
Cl-6.5(Cross Hatch Test)	-	1000	-
Cl-6.7(Other Tests)	-	0	-
Cl-7.3.1(Gloss)	-	2000	-
Cl-7.3.2(Colour)	-	1000	-
Cl-8.1, Table-4 (i)(Undercut at scribed lines)	-	10000	-
Cl-8.1, Table-4 (ii)(Corrosion of the base metal)	-	0	-
Cl-8.1, Table-4 (iii)(Blistering)	-	0	-
Cl-9.1(The nominal thickness of sheets)	-	0	-
Cl-9.2(The case of strips)	-	1000	-
Cl-9.3(Mass of each pack)	-	0	-
Cl-9.4.1(Tolerances on thickness sheets and strips)	-	1000	-
Cl-9.4.2(Width)	-	1000	-
Cl-9.4.3(Length)	-	1000	-
Cl-9.4.4(Mass)	-	1000	-
Cl-10.1(Camber)	-	1000	-
Cl-10.2(Deviation from Squareness (Out-of Square)	-	1000	-
Cl-10.3(Deviation from Flatness)	-	1000	-
Cl-14(Marking)	-	0	-
Cl-8.2 Table 5 (i)(Undercut at scribed lines)	-	0	-
Cl-8.2 Table 5 (ii)(Blistering)	-	0	-
Cl-4.3(Organic Coating)	-	2000	-
Cl-4.4(Dry Film Thickness)	-	2000	-
Cl-6.6(Solvent Resistance Test)	-	4000	-

18 Dec, 2027

-
Included w.e.f 21.10.2024

125

IS 18573 (2024)

Cold formed welded carbon steel square and rectangular hollow sections for mechanical, general engineering and decorative purposes ï¿½ Specification

All

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause.4.0(Carbon)	-	1000	-
Clause.4.0(Sulphur)	-	1000	-
Clause.4.0(Phosphorus)	-	1000	-
Clause.4.0(Sulphur)	-	1000	-
Clause.4.0(Silicon)	-	1000	-
Clause.4.0(Manganese)	-	1000	-
Clause.6.0(Workmanship)	-	1000	-
Clause.7.0(Straightness)	-	1000	-
Clause.8.0(Basis of Calculation)	-	500	-
Clause.9.0(Length)	-	1000	-
Clause.11.0(Outside Dimension)	-	1000	-
Clause.11.0(Thickness)	-	1000	-
Clause.11.0(Concavity and Convexity)	-	2000	-
Clause.11.0(Squareness of Sides)	-	1000	-
Clause.11.0(External Corner Radiius)	-	1000	-
Clause.11.0(Straightness and twist)	-	1000	-
Clause.13.0(Surface Protection)	-	2000	-
Clause.15.0(Tensile test)	-	2000	-
Clause.15.0(Yield strength)	-	2000	-
Clause.15.0(Elognation Percent)	-	2000	-
Clause. 3.0(Types)	-	0	-
Clause.5.0(Supply of Material)	-	0	-
Clause.5.0(Supply of Material)	-	0	-
Clause.10.0(Dimensions and properties)	-	1000	-
Clause.10.0(Dimensions and properties)	-	1000	-
Clause.11.0(General)	-	0	-
Clause.11.0(Thickness)	-	1000	-
Clause.12.0(Dimension Tolerances)	-	1000	-
Clause.12.0(Dimension Tolerances)	-	1000	-
Clause.14.0(Testing)	-	0	-
Clause.18.0(Marking)	-	0	-
6(Workmanship)	-	1000	-
10(Dimensions and Properties)	-	1000	-
11(Measurement of Shape and Size)	-	1000	-
12(Dimensions and Tolerances)	-	1000	-
13(Surface Protection)	-	2000	-
15(Tensile Test)	-	2000	-

18 Dec, 2027

-
Included w.e.f 21.10.2024

126

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	7000	For Raw material Testing charges .
Cl-4.2(Carbon content of finished PE lateral pipe)	-	1000	ok
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	1000	-
Cl-6.0(Visual Appearance)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	1000	Acceptance Test
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	5000	-
Cl-7.2(Reversion Test)	-	1500	-
Cl-7.3(Tensile Test)	-	1500	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	2500	-
Cl-9.0(Coiling)	-	500	-
Cl-8.0(Supply of pipes)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	1000	-
6(Visual Appearance)	-	500	-
7.1 & Table 2(Hydraulic Characteristics)	-	1000	Acceptance
7.1 & Table 2(Hydraulic Characteristics)	-	5000	Quality
7.2(Reversion Test)	-	1500	-
7.3(Tensile Strength)	-	1500	-
7.3(Elongation at Break)	-	1500	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	2500	-
4.2(a)(Carbon Black Content-IS 2530)	-	1500	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	1500	-
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	1000	-

18 Dec, 2027

-
Included w.e.f. 06.11.2024

127

IS 14650 (2023)

UNALLOYED AND ALLOYED STEEL INGOT AND SEMI-FINISHED PRODUCTS FOR RE-ROLLING PURPOSES - SPECIFICATION (First Revision)

All

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 7.1(CARBON)	-	1000	-
Clause - 7.1(SULPHUR)	-	1000	-
Clause - 7.1(PHOSPHURS)	-	1000	-
Clause - 7.1(MANGANESE)	-	1000	-
Clause - 7.1(NITROGEN)	-	2000	-
Clause - 7.1(CARBON)	-	1000	-
Clause - 7.1(SULPHUR)	-	1000	-
Clause - 7.1(PHOSPHURS)	-	1000	-
Clause - 7.1(MANGANESE)	-	1000	-
Clause - 7.1(NITROGEN)	-	2000	-
Clause - 7.1(CARBON)	-	1000	-
Clause - 7.1(SULPHUR)	-	1000	-
Clause - 7.1(PHOSPHURS)	-	1000	-
Clause - 7.1(MANGANESE)	-	1000	-
Clause - 7.1(NITROGEN)	-	2000	-
As per Clause 10(Dimension)	-	1000	-
As per Clause 10.1(Dimension Width)	-	1000	-
As per Clause 10.1(Dimension Thickness)	-	1000	-
As per Clause 10.2(Dimension Length)	-	1000	-
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	0	-
As per Clause 11.5(Bend)	-	1000	-
As per Clause 11.6(Camber)	-	1000	-
As per Clause 11.7 (i)(Out of Square)	-	1000	-
As per Clause 11.7 (ii)(Round Corners)	-	500	-
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	500	-
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	500	-
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	500	-
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	500	-
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	500	-
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	500	-
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	1000	-
As per Clause 11.7 (ix)(Scarfing pits)	-	500	-
Clause. 13(Macro examination test.)	-	5000	-
Clause. 13(Macro examination test.)	-	0	-
Clause. 13(Sulphur print.)	-	8000	-
Clause. 14(Marking)	-	0	-
Clause.15(Ordering information)	-	0	-
Clause.6.0(Manufacture)	-	0	-
Clause.7.1(Silicon)	-	1000	-
Clause.7.1(Carbon Equbalant)	-	500	-
Clause.7.1(Microalloy element)	-	500	-
Clause - 7.1(CARBON)	-	1000	-
Clause - 7.1(SULPHUR)	-	1000	-
Clause - 7.1(PHOSPHURS)	-	1000	-
Clause - 7.1(MANGANESE)	-	1000	-
Clause - 7.1(NITROGEN)	-	2000	-
As per Clause 10(Dimension)	-	1000	-
As per Clause 10.1(Dimension Width)	-	1000	-
As per Clause 10.1(Dimension Thickness)	-	1000	-
As per Clause 10.2(Dimension Length)	-	1000	-
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	0	-
As per Clause 11.5(Bend)	-	1000	-
As per Clause 11.6(Camber)	-	1000	-
As per Clause 11.7 (i)(Out of Square)	-	1000	-
As per Clause 11.7 (ii)(Round Corners)	-	500	-
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	500	-
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	500	-
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	500	-
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	500	-
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	500	-
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	500	-
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	1000	-
As per Clause 11.7 (ix)(Scarfing pits)	-	500	-
Clause. 13(Macro examination test.)	-	0	-
Clause. 13(Macro examination test.)	-	5000	-
Clause. 13(Sulphur print.)	-	8000	-
Clause. 14(Marking)	-	0	-
Clause.15(Ordering information)	-	0	-
Clause.6.0(Manufacture)	-	0	-
Clause.7.1(Silicon)	-	1000	-
Clause.7.1(Carbon Equbalant)	-	1000	-
Clause.7.1(Microalloy element)	-	1000	-
Clause - 7.1(CARBON)	-	0	-
Clause - 7.1(SULPHUR)	-	0	-
Clause - 7.1(PHOSPHURS)	-	0	-
Clause - 7.1(MANGANESE)	-	0	-
Clause - 7.1(NITROGEN)	-	0	-
As per Clause 10(Dimension)	-	1000	ok
As per Clause 10.1(Dimension Width)	-	1000	ok
As per Clause 10.1(Dimension Thickness)	-	1000	ok
As per Clause 10.2(Dimension Length)	-	1000	ok
As per Clause 11/11.1/11.2/11.3/11.4(Tolerances)	-	0	-
As per Clause 11.5(Bend)	-	1000	ok
As per Clause 11.6(Camber)	-	0	-
As per Clause 11.7 (i)(Out of Square)	-	0	-
As per Clause 11.7 (ii)(Round Corners)	-	0	-
As per Clause 11.7 (iii)(Ridges due to gas cutting)	-	0	-
As per Clause 11.7 (iv)(Taper (Width variation on top and bottom surface at one location)	-	0	-
As per Clause 11.7 (v)(Edge slanting (Width variation on top and bottom surface at one location)	-	0	-
As per Clause 11.7 (vi)(Convexity(Difference in thickness from edge to curve)	-	0	-
As per Clause 11.7 (vii)(Chamfering (Length variation on top and bottom surface at one location)	-	0	-
As per Clause 11.7 (viii)(Wedge (Thickness variation at the edges along the cross section)	-	0	-
As per Clause 12/12.1/12.2/12.3(Freedom from defects)	-	0	-
As per Clause 11.7 (ix)(Scarfing pits)	-	0	-
Clause. 13(Macro examination test.)	-	0	-
Clause. 13(Macro examination test.)	-	0	-
Clause. 13(Sulphur print.)	-	0	-
Clause. 14(Marking)	-	0	-
Clause.15(Ordering information)	-	0	-
Clause.6.0(Manufacture)	-	0	-
Clause.7.1(Silicon)	-	0	-
Clause.7.1(Carbon Equbalant)	-	0	-
Clause.7.1(Microalloy element)	-	0	-

18 Dec, 2027

-
Included w.e.f. 09.11.2024 Excluding Cl.13 (Optional Test)

128

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.4(Carbon Black Content)	-	1000	-
Cl.4.1.4(Carbon Black Di spersion)	-	1500	-
Cl.4.1.3(Den sity Test)	-	1500	-
Cl.4.1.3(MFR Test)	-	1000	-
Cl.4.1.3(Thermal Stabi lity)	-	5000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1000	-
Cl.4.1.3, T-1(Water Content)	-	1500	-
4.2(Metallic Couplers)	-	4500	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	500	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	500	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	500	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	500	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	500	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	500	-
5(Dimensions of pipe - i) Outside diameter)	-	1000	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	1000	-
4.1.3(Workmanship and appearance)	-	1000	-
7.2.1(Visual and Workmanship Requirement)	-	500	-
Cl.7.1.2(Hydraulic Characteristic)	-	5000	-
Cl.7.1.2(Hydraulic Characteristic)	-	10000	-
Cl.7.1.3(Reversion Test)	-	1500	-
Cl.7.1.4(Tensile Test)	-	1500	-
Cl.7.1.5(Fusion Compatibility)	-	8000	-
Cl.7.1.6(Corrected Density)	-	1000	-
Cl.7.1.7(MFR Test)	-	1000	-
Cl.7.2.l(Leakage Test)	-	1000	-
Cl.7.2.2(Cl.7.2.2)	-	1000	-
Cl.7.2.3(Weld ability Test)	-	10000	-
6.2, 6.2.1(Quick Coupled Fittings)	-	10000	-

18 Dec, 2027

-
Included w.e.f. 27.01.2023.

129

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

All grades except X02Cr24Ni22Mo7N & X02Cr24Ni17Mo4Mn6N

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	-
Cl. 7.1 & 7.2 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	-
Cl. 7.1 & 7.2 Table 1(Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	-
Cl. 7.1 & 7.2 Table 1(Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	-
Cl.12(Corrosion Resistance- IS 10461(Part1))	-	5000	-
Cl.12(Corrosion Resistance- IS 10461(Part2))	-	5000	-
6(Freedom from defects , IS 6911)	-	500	-
10.1,Table 4&Table 6(Tensile Test - IS 1608(Pt -1))	-	5000	-
10.2,Table 4&Table 5(Hardness Test- IS 1500(Pt -1),IS 1501 (Pt-1),IS 1586 (Pt -1))	-	1000	-
10.3(Bend Test - IS 1599)	-	1000	-
11,Table 7(Erichsen cupping test-IS 10175)	-	5000	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	5000	-
10.1 Amd 2(Elongation)	-	5000	-
Clause 17 , Table 9 to Table 19(Dimension (Length))	-	1000	-
Clause 17 , Table 9 to Table 19(Dimension (Width))	-	1000	-
Clause 17 , Table 9 to Table 19(Dimension (Thickness))	-	1000	-
Clause 17 , Table 9 to Table 19(Camber)	-	1000	-
Clause 17 , Table 9 to Table 19(Flatness)	-	1000	-
10.1 Amd 2(Yeild Strength)	-	5000	-

18 Dec, 2027

-
Included w.e.f. 19.05.2023.

130

IS 16333 : Part 3 (2022)

Mobile phone handsets: Part 3 Indian language support for mobile phone handsets - Specific requirements(Second Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Inputting of text)	-	10000	-
5.2(Message Readability)	-	15000	-
6(Marking)	-	5000	-

18 Dec, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

Kailtech Test and Research Centre Pvt. Ltd., Indore

141C, Electronic Complex Industrial Area, Indore, Indore, Madhya Pradesh, 452010

- contact@kailtech.net

Scope List