BIS - LIMS (Laboratory Information Management System)

Mbis Tescon Private Limited

DDA SHED NO. A-120, OKHLA INDUSTRIAL AREA, PHASE-2, New Delhi, South, Delhi, 110020

8799786535 info@mbistesconlabs.com

Scope List

Reset

41 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

All varity

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	300	Film:10000 & material:7000 for bis testing charges and for others 1.5 time of bis testing charges
5.1.2(Film Form)	-	300	-
5.1.3(Odour)	-	300	-
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	300	-
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	1000	-
5.1.6(Ash content - IS 2508: 2024)	-	1000	-
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	1000	-
5.1.6(carbon black dispersion - IS 2530: 1963)	-	1000	-
5.2.1.2(Nominal Width)	-	300	-
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2000	-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2000	-
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	2000	-
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	1500	-
" 7, Type 2 (HDPE/PE) /Table-2"("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
" 7/Table-2"("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
" 7/Table-2"("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
" 7/Table-2"("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1500	-
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2000	-
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	2000	-
" 7/Table-2"(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	2000	-
8, Type 3 (LDPE/LLDPE, PE) /Table-3("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
8/Table-3("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
8/Table-3("Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
8/Table-3("Average Tensile Break Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
8/Table-3(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1500	-
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	2000	-
9, Type 4 (HDPE/PE) /Table-4("Average Yield strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
9/Table-4("Average Yield strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
9/Table-4("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
9/Table-4("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
9/Table-4("Average Tensile yield Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
9/Table-4("Average Tensile yield Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1500	-
9/Table-4(Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3))	-	1500	-
9/Table-4(Average Tensile Break Elongation -Transverse Direction, IS 13360 (Part 5/Sec 1) and S 13360 (Part 5/Sec 3))	-	1500	-
9/Table-4(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1500	-
Cl-4.2.3.1.4 (a)(Density)	-	500	-
Cl-4.2.3.1.4 (b)(Toluene Extract)	-	2000	-
Cl-4.2.3.1.4 (c)(Volatile Matter, Max)	-	2000	-
Cl-4.2.3.1.4 (d)(Carbon Black Particle Size)	-	1000	-
Cl-4.2.3.1.4 (e)(Tint Strength)	-	1500	-
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	500	-
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	1500	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

all variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	100	-
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	100	-
3.2.3(Socket, Measurement)	-	200	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	200	-
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	100	-
3.2.3(Socket, measurements)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

All varity upto size 500mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	200	-
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	200	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2, 3.2.1, Fig 2(Manufacture)	-	100	-
3.2.2, Fig 1, table 1(Dimensions)	-	100	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	100	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 45o Bend)	-	100	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2, 3.2.1, Fig 2(Manufacture)	-	100	-
3.2.2, Fig 1, table 1(Dimensions)	-	100	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	100	-
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	100	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2, 3.2.1, Fig 2(Manufacture)	-	100	-
3.2.2, Fig 2, table 2(Dimensions)	-	100	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	100	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	100	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

All variety upto size 110 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	6000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.3, 3.3.1, Fig 1(Manufacture)	-	100	-
3.2(Materials)	-	6000	-
3.3.2, table 1, fig 1(Dimensions)	-	100	-
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	100	-
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2, 3.2.1, Fig 1(Manufacture)	-	100	-
3.2.2, Fig 2, table 2(Dimensions)	-	200	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	100	-
Table 2 (Cl.3.2.2, and Fig.1)(Dimensions of Flanged Tail Piece with Metallic Flange for Elastomeric Sealing Ring Joint)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

All variety upo size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2, 3.2.1, Fig 1(Manufacture)	-	100	-
3.2.2, Fig 1(Dimensions)	-	200	-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Equal Tees)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.1(General)	-	12000	-
3.2, 3.2.1, Fig 1(Manufacture)	-	100	-
3.2.2, Fig 1(Dimensions)	-	200	-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	12000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2, 3.2.1, Fig 1(Manufacture)	-	100	-
3.2.2, Fig 1(Dimensions)	-	200	-
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	100	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

All variety upto size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	9000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	100	-
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	100	-
Clause 3.2.2, and Fig. 2.(B)	-	100	-
Clause 3.2.2, and Fig. 2(Nominal size)	-	100	-
3.2.1, Table-1, Fig-1(Plumbing)	-	100	-
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	100	-
3.2.1, Table-1, Fig-1(B)	-	100	-
3.2.1, Table-1, Fig-1(Nominal size)	-	100	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	3000	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	0	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	0	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Mercury (all three extracts))	-	0	-
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-10)(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction))	-	0	-
10.7 of IS 4985(Sulphated Ash content, Annex-B of IS 4985)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

All variety upto Size 500 mm

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	6000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
4(Size of fitting)	-	100	-
5.1 Table-1 Fig.1(Dimension of Socket length)	-	100	-
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	100	-
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	100	-
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	100	-
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	1000	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	2000	-
6.3(Effect on water test)	-	3000	-
8(Marking)	-	0	-
3.2.3(socket, measurements)	-	0	-
3.1(Material)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

All Variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	6000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
2.2(Manufacture)	-	200	-
2.2.2(diameter of the socket of cap)	-	200	-
6.1.1(VCM Content Test)	-	6000	-
2.1(General)	-	0	-
2.2.2(diameter of the socket of cap)	-	0	-
2.2.2 table 1(Laying length)	-	0	-
2.2(Manufacture)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

All variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	6000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
2.2(Manufacture)	-	100	-
2.2.2, Table 1(Size)	-	100	-
2.2.2, Table 1(Union Laying Length)	-	100	-
2.2.3( inside diameter of the socket)	-	100	-
2.2.3(Socket length)	-	100	-
6.1.1(VCM Content Test)	-	6000	-
2.2.2 table 1(Laying length)	-	100	-
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(Union Laying Length)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
2.2.3(Socket length)	-	0	-
table 1 sl.no: 06(50 )	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

All variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	6000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
2.2(Manufacture)	-	100	-
2.2.2, Table 1(Size)	-	100	-
2.2.2, Table 1(Socket Laying Length)	-	100	-
2.2.3( inside diameter of the socket)	-	100	-
2.2.3(Socket length)	-	100	-
6.1.1(VCM Content Test)	-	6000	-
2.2.2 table 1(Laying length)	-	100	-
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 08(75 )	-	0	-
table 1 sl.no: 09(90 )	-	0	-
table 1 sl.no: 10(110 )	-	0	-
table 1 sl.no: 11(125 )	-	0	-
table 1 sl.no: 12(140 )	-	0	-
table 1 sl.no: 13(160 )	-	0	-
table 1 sl.no: 14( 180 )	-	0	-
table 1 sl.no: 15(200 )	-	0	-
table 1 sl.no: 16(225 )	-	0	-
table 1 sl.no: 17(250.0)	-	0	-
table 1 sl.no: 18(280.0)	-	0	-
table 1 sl.no: 19(315.0)	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(Socket Laying Length)	-	0	-
2.2.3(Socket length)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
table 1 sl.no: 06(50 )	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

All variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	6000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
2.2(Manufacture)	-	100	-
2.2.2, Table 1(Size)	-	100	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	100	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	100	-
2.2.3( inside diameter of the socket)	-	100	-
2.2.3(Socket length)	-	100	-
6.1.1(VCM Content Test)	-	600	-
2.2.2 table 1(Laying length)	-	100	-
table 1 sl.no: 01(16 (Z) )	-	0	-
table 1 sl.no: 02(20 (Z) )	-	0	-
table 1 sl.no: 03(25 (Z) )	-	0	-
table 1 sl.no: 04(32 (Z) )	-	0	-
table 1 sl.no: 05(40 (Z) )	-	0	-
table 1 sl.no: 06(50 (Z) )	-	0	-
table 1 sl.no: 07(63 (Z) )	-	0	-
table 1 sl.no: 08(75 (Z) )	-	0	-
table 1 sl.no: 09(90 (Z) )	-	0	-
table 1 sl.no: 10(110 (Z) )	-	0	-
table 1 sl.no: 11(125 (Z) )	-	0	-
table 1 sl.no: 12(140 (Z) )	-	0	-
table 1 sl.no: 13(160(z))	-	0	-
table 1 sl.no: 02(20 (Z1) )	-	0	-
table 1 sl.no: 01(16 (Z1) )	-	0	-
table 1 sl.no: 03(25 (Z1) )	-	0	-
table 1 sl.no: 04(32 (Z1) )	-	0	-
table 1 sl.no: 05(40 (Z1) )	-	0	-
table 1 sl.no: 06(50 (Z1) )	-	0	-
table 1 sl.no: 07(63 (Z1) )	-	0	-
table 1 sl.no: 08(75 (Z1) )	-	0	-
table 1 sl.no: 09(90 (Z) )	-	0	-
table 1 sl.no: 10(110 (Z1) )	-	0	-
table 1 sl.no: 11(125 (Z1) )	-	0	-
table 1 sl.no: 12(140 (Z1) )	-	0	-
table 1 sl.no: 13(160(z1))	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	0	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
2.2.3(Socket length)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

All variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	6000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
2.2(Manufacture)	-	100	-
2.2.2, Table 1(Size)	-	100	-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	100	-
2.2.3( inside diameter of the socket)	-	100	-
2.2.3(Socket length)	-	100	-
6.1.1(VCM Content Test)	-	6000	-
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 06(50 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 08(75 )	-	0	-
table 1 sl.no: 09(90 )	-	0	-
table 1 sl.no: 10(110 )	-	0	-
table 1 sl.no: 11(125 )	-	0	-
table 1 sl.no: 12(140 )	-	0	-
table 1 sl.no: 13(160 )	-	0	-
table 1 sl.no: 15(200 )	-	0	-
table 1 sl.no: 14( 180 )	-	0	-
table 1 sl.no: 16(225 )	-	0	-
table 1 sl.no: 17(250.0)	-	0	-
table 1 sl.no: 18(280.0)	-	0	-
table 1 sl.no: 19(315.0)	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
2.2.3(Socket length)	-	0	-
2.2.2 table 1(Laying length)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

All Variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	300	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
2.2.2 table 1(Laying length)	-	100	-
6.1.1(VCM Content Test)	-	6000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	6000	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	0	-
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

All variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5000	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
2.2(Manufacture)	-	100	-
2.2.2, Table 1(Size)	-	100	-
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	100	-
2.2.3( inside diameter of the socket)	-	100	-
2.2.3(socket length)	-	100	-
6.4 PART-1(Short term hydraulic test)	-	1000	-
6.1.1(VCM Content Test)	-	6000	-
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 06(50 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 08(75 )	-	0	-
table 1 sl.no: 09(90 )	-	0	-
table 1 sl.no: 10(110 )	-	0	-
table 1 sl.no: 11(125 )	-	0	-
table 1 sl.no: 12(140 )	-	0	-
table 1 sl.no: 13(160 )	-	0	-
table 1 sl.no: 14( 180 )	-	0	-
table 1 sl.no: 15(200 )	-	0	-
table 1 sl.no: 16(225 )	-	0	-
table 1 sl.no: 17(250.0)	-	0	-
table 1 sl.no: 18(280.0)	-	0	-
table 1 sl.no: 19(315.0)	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
2.2.3(socket length)	-	0	-
2.2.2 table 1(Laying Length)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

All variety

6400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	100	fitting:6400 & Resin :6000 for bis testing charges and for others 1.5 time of bis testing charges
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	100	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	100	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	100	-
Cl. 6.1(Stress Relief Test- Appendix A)	-	1000	-
Cl. 6.2(Opacity- Appendix B)	-	1000	-
6.3(Effect on Water)	-	3000	-
6.4(Short-Term Hydraulic Test)	-	1000	-
6.1.1(VCM Content Test)	-	6000	-
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	-
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	-
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	0	-
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	0	-
3(Size of Fitting -)	-	0	-
4(Minimum thickness)	-	0	-
5(Socket dimensions)	-	0	-
6.1(Stress Relief Test)	-	0	-
6.2(Opacity)	-	0	-
7.2(Production Routine Tests)	-	0	-
Cl 6.3(Effect on Water Lead (first extraction))	-	0	-
Cl 6.3(Effect on Water Lead (third extraction))	-	0	-
Cl 6.3(Effect on Water Dialkyl tin C4 and higher homologues(measuredas tin )(third extraction ))	-	0	-
Cl 6.3(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	0	-
Cl 6.3(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	0	-
CL 4.0(Wall thickness (average of 4.0))	-	0	-
CL 5.1(Sockt Length ( Take 4 reading and minimum will be reported))	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 8360 (2022)

Fabricated Polyethylene Fittings for Water Supply ï¿½ Specification (First Revision)

All vriety upto size 500 mm

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Materials)	-	14000	Fittings:6000 & material :14000 As per IS 4984 for bis testing charges and for others 1.5 time of bis testing charges
5(Sizes and Designation of Fittings)	-	200	-
6(Visual Appearance)	-	200	-
7(Dimensions of Fittings)	-	600	-
8.1(Hydraulic Characteristics)	-	4000	-
8.2(Tensile Strength for Butt-Fusion)	-	1000	-
9.1.2(Type Tests for Fittings Sizes)	-	0	-
9.2.2(Lot)	-	0	-
9.2.3(Visual and Dimensional Requirements for Fabricated PE Fittings)	-	0	-
9.2.4.1(Fittings sizes up to 560 mm)	-	0	-
9.2.4.2(Fittings sizes including and above 630 mm)	-	0	-
10(Marking)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 8008 (2022)

Injection Moulded/Machined Polyethylene Fittings for Water Supply ï¿½ Specification ( Second Revision )

All variety upto size 500 mm

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	14000	Fittings :20000, resin:7000,master batch :7000 for bis testing charges and for other 1.5 times of bis testing charges
5(COLOUR)	-	200	-
6.1(The nominal outside diameter)	-	200	-
6.2(Bends, tees, pipe ends and end caps designation)	-	200	-
7(WELD LENGTH)	-	200	-
8(VISUAL APPEARANCE)	-	200	-
9.1(DIMENSIONS OF FITTINGS)	-	2000	-
9.2(DIMENSIONS OF FITTINGS)	-	200	-
9.3(DIMENSIONS OF FITTINGS)	-	500	-
10.1.1(Length of Pipe for Welding Test)	-	10000	-
10.1.2(Sandwich Flange Hydraulic Testing)	-	500	-
10.2(Carbon Black Content and Dispersion)	-	3000	-
10.3(Melt Flow Rate)	-	1500	-
10.4(Density)	-	500	-
10.5(Oxidation Induction Time)	-	2500	-
10.6(Overall Migration)	-	2500	-
11.1(Type Tests)	-	0	-
11.2(Acceptance Tests)	-	0	-
4.2(Material)	-	0	-
4.1(Material)	-	0	-
4.2(Material)	-	0	-
4.3(Rework Material)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 17546 (2021)

Chlorinated polyvinyl chloride CPVC fittings for potable hot and cold water distribution supplies Specification

All variety

85000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Dimensions of fitting)	-	3000	Fittings :85000 & Raw material 20000 for bis testing charges and for others 1.5 times of bis testing charges
8.2(Opacity)	-	1500	-
8.1(Visual Appearance)	-	200	-
8.4(Vicat softening Temperature)	-	2000	-
8.3(Stress Relief Test)	-	2000	-
8.5(Density)	-	500	-
8.6(Effect on water)	-	5000	-
9(Mechanical Properties)	-	0	-
11(Marking)	-	0	-
Cl-6.2.2(Compound Chlorine Content)	-	2000	-
Cl-6.2.5(Verification of the Malfunction Temperature)	-	18000	-
Cl-9.1(Hydrostatic Characteristics)	-	29000	-
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	28000	-
6(Composition)	-	20000	-
3.1(Nominal Size(DN))	-	200	-
3.2(Nominal Outside Diameter)	-	200	-
3.3(Mean Inside Diameter of Socket at Entry)	-	200	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	200	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	200	-
3.5(Out-of-Roundness (Ovality))	-	200	-
3.6(Nominal Wall Thickness)	-	200	-
3.7(Minimum Wall Thickness)	-	200	-
3.8(Tolerance)	-	200	-
3.9(Working Pressure)	-	0	-
3.11(Type Tests)	-	60000	-
3.11(Acceptance Tests)	-	50000	-
3.1(Standard Dimension Ratio)	-	200	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

All variety upto size 500 mm

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	5000	pipe :16000 & Resin :5000 for bis testing charges and for others 1.5 times of bis testing charges
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	200	-
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	200	-
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	200	-
6.1.3 (Length of Pipe)	-	200	-
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	200	-
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	200	-
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	200	-
6.1.4, Table 3(iv) Length of spigot, l1)	-	200	-
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	200	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	200	-
6.1.4.1 (e3min=0.75e)	-	200	-
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	200	-
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	200	-
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	200	-
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	200	-
7(Physical characteristics )	-	0	-
7.1(Appearance:- )	-	200	-
7.1(Appearance:- )	-	200	-
7.2(Colour )	-	200	-
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1500	-
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1500	-
8(MECHANICAL CHARACTERISTICS)	-	0	-
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	2000	-
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	2000	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	2000	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	5000	-
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	2000	-
9.2 IS 14182(b) Solvent cement)	-	0	-
10(Performance requirements)	-	0	-
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	1000	-
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	-
'7.5 (amdt.7)(Effect on Water (Type test))	-	5000	-
5.3(Qualitative)	-	0	-
12(Marking)	-	100	-
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	0	-
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

All Variety

85000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	200	PIPE :85000, raw materail:20000 for bis testing chrges and for others 1.5 time of bis testing charges
7.1,7.1.1 IS 12235 (Part 1) Table 2(Outside Diameter at any point)	-	200	-
7.1.2 IS 12235 (Part 1) Table 2(Wall Thickness )	-	200	-
7.1.3 (Effective length)	-	200	-
8(Pipe Ends)	-	500	-
9(PHYSICAL AND CHEMICAL CHARACTERISTICS)	-	0	-
9.1(Visual Appearance)	-	200	-
9.1(Visual Appearance)	-	200	-
9.2 IS 12235 (Part 3)(Opacity)	-	1000	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	1000	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	1000	-
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	1000	-
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	1000	-
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	1000	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	1000	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	1000	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	1500	-
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	1500	-
9.6 IS 12235(Part 14)(Density)	-	500	-
10(Mechanical Properties)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	3000	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	18000	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	8000	-
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	28000	-
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	2000	-
10.4 IS 12235(Part 19)(Flattening Test)	-	2000	-
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	2000	-
5 Table 1(Classification of pipes)	-	0	-
6.2.1 Annex B(Chloride Content of Resin)	-	2000	-
6.3(Compound Properties)	-	20000	-
6.3.1 Annex B(Chloride content)	-	2000	-
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	18000	-
6.3(K value Test)	-	2000	-
6.3.3(Density)	-	500	-
5 Table 1(Classification of pipes)	-	0	-
6.2.1 Annex B(Chloride Content of Resin)	-	0	-
6.3(Compound Properties)	-	0	-
6.3.1 Annex B(Chloride content)	-	0	-
6.3.2 Annex C(Verification of the Malfunction Temperature, Tmal: )	-	0	-
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	0	-
7.1 IS 12235 (Part 1) Table 2(Dimension of Pipes: Mean outside Diameter)	-	0	-
7.1,7.1.1 IS 12235 (Part 1)Table 2(Outside Diameter at any point (Minimum))	-	0	-
7.1.2 IS 12235 (Part 1)Table 2(Wall Thickness (Minimum))	-	0	-
7.1.3 (Effective length)	-	0	-
8.0(Pipe Ends)	-	0	-
9.0(PHYSICAL AND 1CHARACTERISTICS)	-	0	-
9.1(Visual Appearance)	-	0	-
9.1(Visual Appearance)	-	0	-
9.2 IS 12235 (Part 3)(Opacity)	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (first extraction))	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Lead (third extraction))	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Cadmium (for all three extracts) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Mercury (for all three extracts) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction) )	-	0	-
Cl. 9.3,IS 4985 Cl. 10.3(Other toxic substances including di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate')	-	0	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2)(Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-	0	-
9.5 IS 12235(Part 2)(Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-	0	-
9.6 IS 12235(Part 14)(Density)	-	0	-
10.0(Mechanical Properties)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	-
10.1 Table 3 IS 12235 (Part 8/Sec 1)(Hydrostatic Characteristics)	-	0	-
10.2 Table 3 IS 12235 (Part 8/Sec 1)(Thermal Stability by Hydrostatic Pressure Testing)	-	0	-
10.3 IS 4985 Table 4(Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-	0	-
10.4 IS 12235(Part 19)(Flattening Test)	-	0	-
10.5 IS 12235(Part 13)(Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-	0	-
7.1.2(Wall Thickness (Maximum))	-	0	-
7.1.1(Outside Diameter at any point (Maximum))	-	0	-
6.3.2 IS 13360 (Part 3/See 1)(Density)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

All Variety

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type of Fitting)	-	200	11000 for BIS testing charges and for others 1.5 times of BIS testing charges
4(Size Designation)	-	200	-
5(Colour of fittings)	-	200	-
7.1,Table 1(Wall thickness)	-	200	-
7.2 ,Table 2&3(Socket Dimensions)	-	1000	-
7.3(Dimensions of waste trap(Nahani Trap)	-	11000	-
8(Sealing Rings)	-	3000	-
10(Workmanship)	-	200	-
11(Design requirements)	-	200	-
11.1(Solvent cement type or Rubber ring type)	-	200	-
11.2(Socket and spigot configeration)	-	200	-
11.4,Table 5(Vent cowl)	-	11000	-
11.5,Table 6(Pipe Clips)	-	11000	-
12(Physical test requirements)	-	0	-
12.1(Visual appearance)	-	200	-
12.2(Stress relief test)	-	1500	-
12.3(Vicat softening tempewrature)	-	1500	-
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	1000	-
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1000	-
Cl.15, Annex B(Sulphated Ash Content)	-	1500	-
16(Mechanical Properties)	-	0	-
16.1(Impact test)	-	1500	-
17(Watet tightness of joint)	-	1000	-
12.4(Effect on water test)	-	5000	-
7.4(Chamfer)	-	200	-
11.3(Access Openings)	-	200	-
Table 4(Dimension of Access Openings)	-	200	-
Cl 12.4(Effect on Water Lead (first extraction))	-	1000	-
Cl 12.4(Effect on Water Lead (third extraction))	-	1000	-
Cl 12.4(Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-	1000	-
Cl 12.4(Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-	1000	-
Cl 12.4(Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-	1000	-
19(Marking)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 13487 (2024)

Irrigation Equipment — Emitters — Specification

All Variety

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7.2(Flow Paths in Emitter)	-	500	5500 for BIS testing charges and for others 1.5 times of BIS testing Charges
Cl-7.4(Emitter Pull-Out)	-	800	-
Cl-8.1.1(Uniformity of Emission Rate)	-	1000	-
Cl-7.3(Resistance to Hydrostatic Pressure)	-	1000	-
Cl-7.1(Construction and Workmanship)	-	100	-
Cl-8.1.2(Emission Rate as Function of Inlet Pressure)	-	1000	-
Cl-5.1(Connections)	-	100	-
Cl-8.1.3(Determination of Emitter Exponent)	-	1000	-
Cl-5.2(Emitter Ends)	-	0	-
Cl-5.3(Materials)	-	0	-
Cl-6.1(Test Specimens)	-	0	-
Cl-6.2.1(polyethylene pipe)	-	0	-
Cl-6.2.2("grease or chemicals ")	-	0	-
Cl-6.2.3(water temperature)	-	0	-
Cl-6.3(Accuracy or Measuring Devices)	-	0	-
Cl-7.4.1(In-Line Emitters)	-	0	-
Cl-7.4.2(On-Line Emitters)	-	0	-
Cl-9(Marking)	-	0	-

11 Nov, 2028

-
Included w.e.f 24.12.2025

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

All variety upto 500 mm

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4( K-Value)	-	3000	10% Discount for bis branch only
5.5( Density, g/cc)	-	500	-
5.3(VCM Content)	-	5000	-
5.6 / 5.6.1( Material Classification, table -1)	-	5000	-
6.0(CLASSIFICATION OF PIPES, table-2)	-	500	-
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	500	-
7.2( Colour)	-	500	-
7.3( Opacity)	-	1000	-
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	1000	-
8.1.2, table 4 to 7(Wall Thickness)	-	500	-
8.1.3 (Length, meter)	-	500	-
8.2 table-9(Dimensions of Integral Socket)	-	1000	-
8.2 table-9( Pipe Ends)	-	500	-
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	10000	-
9.2, table -11( Resistance to External Blows at 0 °C)	-	2000	-
9.3 table-12( Ring Stiffness)	-	5000	-
5 / 5.1(MATERIALS )	-	5000	-
9.4, annexure-E( Orientation Factor)	-	3000	-
Cl.10, Table 10/1(Vicat Softening Temp (C))	-	1000	-
Cl.10, Table 10/2(Effect on Water)	-	5000	-
Cl.10, Table 10/3(Resistant to di-chloromethane (Degree of gelation))	-	2000	-
Cl.10, Table 10/4(Alternate Test (Tensile test))	-	2000	-
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	2000	-
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	10000	-
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	2000	-
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	2000	-
12(a)( ELASTOMERIC SEALS)	-	3000	-
12(b)( ELASTOMERIC SEALS)	-	3000	-

11 Nov, 2028

-
Included w.e.f 18.12.2025

Bureau of Indian Standards

The National Standards Body of India

Mbis Tescon Private Limited

DDA SHED NO. A-120, OKHLA INDUSTRIAL AREA, PHASE-2, New Delhi, South, Delhi, 110020

8799786535 info@mbistesconlabs.com

Scope List