BIS - LIMS (Laboratory Information Management System)

Dynamic Test and Research Centre

House No. D-7, Kh. No. 6/21, Block-D, Rama Vihar, Village Mohammadpur Majri, Karala, New Delhi-110081, Delhi, North West, Delhi, 110081

9911092203 info@dtrclab.com

Scope List

Reset

10 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 398 : Part 2 (2025)

Aluminium Conductor for Overhead Transmission Purposes - Specification Part 2 Aluminium Conductors Galvanized Steel Reinforced (Fourth Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Material)	-	1000	Rs. 8000/- (up to 100 Sq.mm)
Cl-6.1.1(chemical composition of high carbon steel)	-	1000	-
Cl-6.2(zinc used for galvanizing)	-	1000	-
Cl-7(Freedom From Defects)	-	1000	-
Cl-8.1(Wires-Nominal Sizes)	-	1000	-
Cl-8.2(Aluminum Conductors, Galvanized Steel- Reinforced)	-	1000	-
Cl-9.1(Joint in Wires)	-	1000	-
Cl-9.2(Aluminium Wires)	-	1000	-
Cl-9.3(Galvanized Steel Wires)	-	1000	-
Cl-10.2(Lay Ratio of Aluminium Conductors Galvanized Steel-Reinforced)	-	1000	-
Cl-13.3(Conductor- Visual examination)	-	1000	-
Cl- 13.5(Conductor- Measurement of lay ratio/direction of lay)	-	1000	-
Cl- 13.12(Conductor- d.c. Resistance test on stranded conductor)	-	2000	-
Cl- 13.14(Conductor- Ultimate tensile strength test on stranded conductor)	-	0	-
Cl- 13.13(Conductor- Surface condition test on stranded conductor)	-	0	-
Cl- 13.15(Conductor- Corona test (for conductors intended for use at 400 kV and above voltage level for a.c. and ± 320 kV and above voltage level for d.c.))	-	0	-
Cl-13.16(Conductor- Radio interference voltage test)	-	0	-
Cl-13.4(Aluminium wires-Measurement of diameter)	-	1000	-
Cl- 13.6(Aluminium wires -Breaking load test)	-	1000	-
Cl- 13.8(Aluminium wires- Wrapping test)	-	1000	-
Cl- 13.9(Aluminium wires- d.c. resistance test)	-	1000	-
Cl- 13.11(Aluminium wires Procedure qualification test on welded joint of aluminium strands)	-	1000	-
Cl- 13.4(Steel wires- Measurement of diameter)	-	1000	-
Cl- 13.6(Steel wires- Breaking load test)	-	1000	-
Cl- 13.7(Steel wires- Ductility test)	-	1000	-
Cl- 13.8(Steel wires- Wrapping test)	-	1000	-
Cl- 13.10(Steel wires- Galvanizing test)	-	1000	-
Cl-13.7.1(Torsion Test)	-	1000	-
Cl-13.7.2(Elongation Test)	-	1000	-
Cl-11.1(Standard Length)	-	1000	-
Cl-11.2(Random Lengths)	-	1000	-

01 Oct, 2029

-
-

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	500	-
7.1 Table-1(Dimensional measurement of wires)	-	500	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	500	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	500	-
9.1(Stranding)	-	500	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	-
9.3(Direction of Lay)	-	500	-
9.4(Multiple layers of wires)	-	500	-
11(Packing and Marking)	-	500	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	500	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	500	-
12.3 Table 1(Elongation Test- Before Stranding)	-	500	-
12.3 Table 1(Elongation Test- After Stranding)	-	500	-
12.4 Table 1(Resistance of Aluminium wire)	-	500	-
9.2(Lay Ratio 24 wire layer)	-	500	-
9.2(Lay Ratio 18 wire layer)	-	500	-
9.2(Lay Ratio 12 wire layer)	-	500	-
9.2(Lay Ratio 3/6 wire layer)	-	500	-
7.2.1(Sizes)	-	500	-
Cl-7.2 (7.2.1, 7.2.2), Table-2(Stranding and Wire Dia)	-	500	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Overall Dia)	-	500	-
Cl. 7.2 (7.2.1, 7.2.2), Table 2(Approx Mass)	-	500	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Calculated Maximum Resistance at 20°C)	-	500	-
Cl- 7.2 (7.2.1, 7.2.2), Table-2(Approx Calculated Breaking Load)	-	500	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	500	-

01 Oct, 2029

-
-

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	500	-
12.3, Table-1(Breaking load before stranding)	-	500	-
12.3, Table-1(Breaking load after stranding)	-	1000	-
12.4(Wrapping test)	-	500	-
12.5, Table 1(Resistance test)	-	1000	-
12.6, Table 3(Measurement of lay ratio)	-	500	-
9.3(Stranding)	-	500	-
6(Freedom from defects)	-	500	-
7.2.1(Sizes)	-	500	-
8, 8.1, 8.2(Joint in wires, except during stranding)	-	500	-
9.2(Lay ratio)	-	500	-
9.4(Multiple layer of wires)	-	500	-
4.1(Resistivity)	-	1000	-
4.2(Density)	-	500	-
4.3(Constant-Mass Temperature Coefficient of Resistance)	-	1000	-
4.4(Coefficient of Linear Expansion)	-	1000	-
5(Material)	-	500	-
7.1.1(Nominal Sizes)	-	500	-
7.2.2(Resistance)	-	1000	-

01 Oct, 2029

-
-

IS 9857 (1990)

Welding cables - Specification (First Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Conductor : Material )	-	1000	-
5(SEPARATOR)	-	1000	-
6(COVERING)	-	1000	-
7(CONDUCTOR : CONSTRUCTION )	-	1000	-
8(S E P A R A T O R)	-	1000	-
9.1(C O V E R I N G : Application )	-	1000	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	2000	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	2000	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	1000	-
9.5(Colour of C o v e r i n g)	-	1000	-
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	2000	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	2000	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	2000	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	2000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	5000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	5000	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	5000	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	5000	-
10.1 c) 3)(Physical tests for covering - Ageing in Air Bomb : Tensile strength variation )	-	5000	-
10.1 c) 3)(Physical tests for covering -Ageing in Air Bomb : Elongation variation at break )	-	5000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	5000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	5000	-
10.1 c) 5)(Hot set test )	-	2000	-
10.1 c) 5)(Permanent set )	-	2000	-
11.1(High Voltage Test ( Water Immersion Test ))	-	2000	-
11.2(Spark Test)	-	1000	-
11.3(Static Flexibility Test)	-	1000	-
11.4(Flammability Test)	-	2000	-
12.1(Manufacturer's Identification)	-	1000	-
12.2(Cable Identification)	-	1000	-
12.3(Cable Code)	-	1000	-
13.1(Packing )	-	1000	-
13.2(Marking)	-	1000	-
14(CABLE RATINGS)	-	1000	-
15(VOLTAGE DROP)	-	1000	-
Table 4(Copper purity test)	-	5000	-
Table 2(Oil resistance - Elongation)	-	5000	-
Table 2(Oil resistance - Tensile strength )	-	5000	-
Table 2(Ageing in air bomb - Elongation)	-	5000	-
Table 2(Ageing in air bomb - Tensile strength )	-	5000	-
Table 1 (Thickness of covering)	-	2000	-
15.1 (d)(Heat Shock Test)	-	2000	-
15.1 (d)(Hot Deformation Test)	-	2000	-
15.1 (d)(Loss Of Mass Test)	-	5000	-
10.1(b), Table 1(Thickness of covering)	-	2000	-

01 Oct, 2029

-
-

IS 9968 : Part 1 (2025)

Elastomer Insulated Cables - Specification Part 1 for Working Voltages up to and including 1100 volts (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Copper Conductor)	-	1000	-
Cl-4.2(Aluminum Conductor)	-	1000	-
Cl-6.1(Proofed Tape)	-	1000	-
Cl-6.2("Polyethylene Terephthalate (PETP) Tape or Plastic Tape or Any Other Suitable Tape")	-	1000	-
Cl-6.3(Glass Tape)	-	1000	-
Cl-7(Fillers)	-	1000	-
Cl-8.1(Textile Braid)	-	1000	-
Cl-8.2(Glass Braid)	-	1000	-
Cl-9.1(General Service Insulated Cables and Flexible Cords)	-	1000	-
Cl-9.2(Heat Resisting Insulated Cables)	-	1000	-
Cl-9.3(Silicon Rubber Insulated Cable)	-	1000	-
Cl-10.1(Preservative Compound)	-	1000	-
Cl-10.2(Varnish)	-	1000	-
Cl-12(separator tape)	-	1000	-
Cl-14(Core Identification)	-	1000	-
Cl-18(Laying UP of Cores)	-	1000	-
Cl-19(Binder Tape)	-	1000	-
Cl-20.2(Thickness of Sheath)	-	2000	-
Cl-20.3(Tolerance on Thickness of Sheath)	-	2000	-
Cl-20.4(Colour)	-	1000	-
Cl-22.1 (i) (a)(Conductor resistance test)	-	2000	-
Cl-22.1 (i) (b)(High voltage test or spark test.)	-	2000	-
Cl-22.1 (ii) (a)(Annealing test (for copper);)	-	2000	-
Cl-22.1 (ii) (b)(Tensile Test ((for aluminium);)	-	2000	-
Cl-22.1 (ii) (c)(Wrapping test (for aluminium);)	-	2000	-
Cl-22.1 (ii) (f)(Tensile strength and elongation at break of insulation and sheath)	-	2000	-
Cl-22.1 (ii) (g)(Hot set test for insulation and sheath)	-	2000	-
Cl-22.1 (ii) (h)(High voltage test)	-	2000	-
Cl-22.1 (ii) (i)(Insulation resistance test)	-	2000	-
Cl-22.1 (iii) (a)(Persulphate test (for tinned copper);)	-	2000	-
Cl-22.1 (iii) (f)(Test for thickness of insulation and sheath and overall diameter)	-	2000	-
Electrical(Tensile strength and elongation at break)	-	2000	-
Cl-22.1 (iii) (g), 2(Ageing in air oven)	-	5000	-
Cl-22.1 (iii) (g), 3(Ageing in air bomb)	-	5000	-
Cl-22.1 (iii) (g), 4(Ageing In oxygen bomb)	-	5000	-
Cl-22.1 (iii) (g), 5(Hot set)	-	2000	-
Cl-22.1 (iii) (g), 6(Oil resistance;)	-	5000	-
Cl-22.1 (iii) (g), 7(Tear resistance)	-	2000	-
Cl-22.1 (iii) (i)(High voltage (water immersion) test;)	-	2000	-
Cl-22.1 (iii) (j)(Flammability test)	-	2000	-
Cl-22.1 (iii) (k)(Water absorption test (for insulation as applicable))	-	5000	-
Cl-24.1(Manufacturer’s Identification)	-	1000	-
Cl-25(Packing and Morning)	-	1000	-
CL. 22.1 (iv) a,(Flexing test for Cords for use with electric iron)	-	2000	-

01 Oct, 2029

-
-

IS 7098 : Part 1 (2025)

Crosslinked Polyethylene Insulated Thermoplastic Sheathed Cables - Specification Part 1 For Working Voltages up to and Including 1 100 Volts (Second Revision)

35600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Conductors -Material)	-	100	-
Cl-5, Table-1 (i)(Tensile strength)	-	500	-
Cl-5, Table-1 (ii) (a)(Elongation at break- Ageing in air oven)	-	1000	-
Cl-5, Table-1 (ii) (b)(Variation in tensile strength, from that without ageing)	-	1000	-
Cl-5, Table-1 (ii) (c)(Variation in elongation at break, from that without ageing)	-	1000	-
Cl-5, Table-1 (iii) (a)(Hot set- Treatment;)	-	500	-
Cl-5, Table-1 (iii) (b)(Hot set- Elongation under load)	-	500	-
Cl-5, Table-1 (iii) (c)(Hot set- Permanent elongation after cooling)	-	500	-
Cl-5, Table-1 (iv)(Shrinkage)	-	100	-
Cl-5, Table-1 (v)(Water absorption (gravimetric))	-	1000	-
Cl-5, Table-1 (vi)(Volume resistivity)	-	500	-
Cl-6.1 (a)(Fillers and inner sheath- Vulcanized or unvulcanized rubber)	-	100	-
Cl-6.1 (B)(Fillers and inner sheath- Thermoplastic materials)	-	100	-
Cl-7(Armouring)	-	100	-
Cl-8(Outer Sheath)	-	100	-
Cl-10.3(Tolerance on Thickness of Insulation)	-	100	-
Cl-11(Core Identification)	-	100	-
Cl-12(Laying up of Cores)	-	100	-
Cl-13(Inner Sheath (Common Covering))	-	100	-
Cl-14.1(Armouring- Application)	-	100	-
Cl-14.1.2(armour round wires/formed wires)	-	100	-
Cl-14.2(Type of Armour)	-	100	-
Cl-14.3(Dimensions)	-	100	-
Cl-14.4(Joints)	-	100	-
Cl-14.5(Resistance)	-	100	-
Cl-15.3(Thickness of Outer Sheath)	-	100	-
Cl-16.1 (i) (a)(Test on conductor: Annealing test (for copper);)	-	100	-
Cl-16.1 (i) (b)(Test on conductor: Tensile test (for aluminium);)	-	100	-
Cl-16.1 (i) (c)(Test on conductor: Wrapping test (for aluminium);)	-	100	-
Cl-16.1 (i) (d)(Test on conductor: Resistance test)	-	500	-
Cl-14.6 (a)(Physical tests on round wires/formed wires- Tensile strength)	-	100	-
Cl-14.6 (b)(Physical tests on round wires/formed wires- Elongation at break)	-	100	-
Cl-14.6 (c)(Physical tests on round wires/formed wires- Torsion test for round wires)	-	100	-
Cl-14.6 (d)(Physical tests on round wires/formed wires- Winding test for formed wires)	-	100	-
Cl-14.6 (e)(Physical tests on round wires/formed wires- Uniformity of zinc coating)	-	100	-
Cl-14.6 (f)(Physical tests on round wires/formed wires- Mass of zinc coating)	-	100	-
Cl-14.6 (g)(Physical tests on round wires/formed wires- Resistivity.)	-	100	-
Cl-10, 13, 15(Test for thickness of insulation and sheath)	-	100	-
Cl-16.1 (v) (1)(PVC Sheath- Tensile strength and elongation at break;)	-	500	-
Cl-16.1 (v) (2)(PVC Sheath- Ageing in air oven)	-	1000	-
Cl-16.1 (v) (3)(PVC Sheath- Loss of mass in air oven)	-	100	-
Cl-16.1 (v) (5)(PVC Sheath- Hot deformation test)	-	500	-
Cl-16.1 (v) (6)(PVC Sheath- Heat shock test)	-	500	-
Cl-16.1 (v) (7)(PVC Sheath- Thermal stability)	-	500	-
Cl-8.3-Table 1A(PE Sheath- Carbon black content)	-	500	-
Cl-8.3-Table 1A(PE Sheath- Tensile strength and elongation at break before and after ageing)	-	1000	-
Cl-8.3-Table 1A(PE Sheath- Hot deformation)	-	500	-
Cl-8.3-Table 1A(PE Sheath- Shrinkage test.)	-	100	-
Cl- Table 1B(LSHF Sheath- Tensile strength and elongation at break before and after ageing)	-	1000	-
Cl- Table 1B(LSHF Sheath- Hot deformation)	-	500	-
Cl- Table 1B(LSHF Sheath- Water absorption test)	-	1000	-
Cl- Table 1B(LSHF Sheath- Shrinkage test)	-	100	-
Cl-17.2(High voltage test)	-	500	-
Cl-17.3(Flammability test)	-	500	-
Cl-17.4(Oxygen index test (FR, FR-LSH or LSHF Sheath))	-	1000	-
Cl-17.5(Flame retardance test on single cable)	-	500	-
Cl-17.6(Flame retardance test on bunched cables (FR, FR-LSH or LSHF Sheathed Cables))	-	5000	-
Cl-17.7(Test for halogen acid evolution (FR-LSH or LSHF Outer Sheath))	-	1000	-
Cl-17.8(Smoke density test (FR-LSH or LSHF Sheath))	-	1000	-
Cl-17.9(Temperature index test; (FR, FR-LSH or LSHF Sheath))	-	1000	-
Cl-17.10(Test for pH and conductivity of LSHF Sheath)	-	500	-
Cl-17.11(Test for light transmission for LSHF Sheathed Cables)	-	5000	-
Cl-16.4 (i)(Cold bend test for outer sheath)	-	500	-
Cl-16.4 (ii)(Cold impact test for outer sheath)	-	500	-
Cl-16.4 (iii)(Cold elongation test for LSHF sheath)	-	500	-
Cl. 9(Conductor - Regarding Construction Compliance)	-	100	-
Cl. 10.4(Application of Insulation)	-	100	-
Cl. 13.3(Thickness of Inner sheath)	-	100	-
Cl. 15.1(Application of Outer sheath)	-	100	-
Cl. 15.2(Clour of Outer sheath)	-	100	-

01 Oct, 2029

-
-

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

90000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1 a) (Conductor : Material )	-	1000	-
4.1.1 b) (Material : Seperator tape )	-	1000	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1(Class of conductor )	-	1000	-
4.1.1 e) (Shape of conductor )	-	1000	-
4.1.1 f) (Nominal size of conductor )	-	1000	-
4.2.1, 11.2, 12.2, 13.2, 14.2(Insulation : Material )	-	1000	-
4.2.2, 11.2, 12.2, 13.2, 14.2(Insulation : Application )	-	1000	-
4.2.3,11.2, 12.2, 13.2(Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-	2000	-
4.2.3, 11.2, 12.2, 13.2, 14.2(Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-	2000	-
4.2.4(Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	2000	-
4.2.4(Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-	2000	-
4.2.4(Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	5000	-
4.2.5(Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	5000	-
4.2.4(Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-	5000	-
4.2.5(Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	5000	-
4.3(Fillers)	-	1000	-
4.4(Binder Tape)	-	1000	-
4.5.1,13.4, 14.4(Sheath : Compound )	-	1000	-
4.5.2, 13.4, 14.4(Sheath : Application)	-	1000	-
4.5.3,13.4, 14.4(Thickness of sheath - Average : IS 10810 (Part 6))	-	2000	-
4.5.3,13.4, 14.4(Thickness of sheath - Minimum : IS 10810 (Part 6))	-	2000	-
4.5.4, 13.4(Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-	2000	-
4.5.4,13.4(Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-	2000	-
4.5.4, 13.4, 14.4(Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-	5000	-
4.5.5, 13.4, 14.4(Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-	5000	-
4.5.4, 13.4, 14.4(Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-	5000	-
4.5.5, 13.4,14.4(Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-	5000	-
4.5.5, 11.3, 12.3, 13.6, 14.6(Overall Dimensions)	-	2000	-
4.5.5.1, 11.3, 12.3,13.5, 14.5(Ovality)	-	2000	-
4.5.6, 13.4(Colour of Sheath)	-	1000	-
5.1(High Voltage Test (at Room Temperature))	-	2000	-
5.2(Spark Test (Routine Test))	-	2000	-
5.3(Flammability Test- IS 10810 (Part 53).)	-	2000	-
5.4(Oxygen Index Test- IS 10810 (Part 58))	-	5000	-
5.5(Temperature Index-IS 10810 (Part 64).)	-	5000	-
5.6(Smoke Density-IS 10810 (Part 63).)	-	10000	-
5.7(Assessment of Halogen- Table 1 of Annex D)	-	10000	-
5.1(Persulphate Test- IS 10810 (Part 4).)	-	2000	-
5.11(Flame Retardant Test- IS 10810 (Part 61),)	-	2000	-
5.12(Hot Set Test- IS 10810 (Part 30).)	-	2000	-
5.12(Permanent Set - IS 10810 (Part 30).)	-	2000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-	5000	-
5.13(Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-	5000	-
5.14(Ozone Resistance Test -IS 10810 (Part 13 ))	-	2000	-
5.15(Cold Bend Test-IS 10810 (Part 20).)	-	2000	-
5.16(Cold Impact Test- IS 10810 (Part 21).)	-	2000	-
6.1, Table 1(CORE IDENTIFICATION)	-	1000	-
6.2(Core Identification by Numbers)	-	1000	-
6.2.1(Preferred Arrangement of Marking)	-	1000	-
6.2.2(Durability)	-	1000	-
7.0(CABLE CODE)	-	1000	-
9.0( IDENTIFICATION)	-	1000	-
10.1(Packing )	-	1000	-
10.2(marking)	-	1000	-
10.2.1(Standards marking)	-	1000	-
13.3, 14.3(assembly of cores )	-	1000	-
6.1(General Requirements)	-	1000	-
6.1.1(Colour Combination Green Yellow)	-	2000	-
12.1(Conductor)	-	1000	-
12.2, Table 4(insulation)	-	1000	-
Table 4(Copper Purity test)	-	5000	-
4.3.1 (e)(Fluorine content test (Fillers))	-	5000	-
4.3.1 (d)(Presence of fluorine test (Fillers))	-	5000	-
4.3.1 (c)(Conductivity test (Fillers))	-	2000	-
4.3.1 (b)(pH test (Fillers))	-	2000	-
4.3.1 (a)(HCl test (Fillers))	-	2000	-
5.7 (a)(HCl test (Assessment of halogen test))	-	5000	-
5.7 (b)(pH test (Assessment of halogen test))	-	5000	-
5.7 (c)(Conductivity test (Assessment of halogen test))	-	2000	-
5.7 (d)(Presence of fluorine test (Assessment of halogen test))	-	2000	-
5.7 (e)(Fluorine content test (Assessment of halogen test))	-	2000	-
Table 2 ,( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )(Insulation Resistance)	-	2000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Conductor Resistance)	-	2000	-
Table 2 , Clause .5.13(Water immersion test (Effect of water on sheath) - TS Variation of Sheath)	-	5000	-
Table 2 , Clause 5.13(Water immersion test (Effect of water on sheath) - Elongation Variation of Sheath)	-	5000	-
"Table 2 ( Clause 11.4, 12.4, 13.7 14.7 and 15.7 )"(Hot Deformation)	-	2000	-
Table 2, III.a.ii(Annealing test (for Cu, before stranding))	-	2000	-
Table 2, II.a, b(Wrapping test before stranding (for Al))	-	2000	-
Cl.4.2.1 & Annex A(Insulation Resistance Constant at Rated Temperature (70°C))	-	2000	-
Table 2, III a (i)(Conductor Resistance)	-	2000	-
Annex A(Hot Deformation)	-	2000	-

01 Oct, 2029

-
-

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Phase/Street Lighting conductor)	-	1000	-
4.2(Messenger (Neutral Conductor or Otherwise))	-	1000	-
5.1(Insulation)	-	1000	-
6.1(Flexibility class)	-	1000	-
6.2(Compactness)	-	1000	-
6.2(No of strands)	-	1000	-
6.2(Surface)	-	1000	-
6.3(Protective barrier)	-	1000	-
6.4(size of street lighting conductor)	-	1000	-
6.5(Size of messenger conductor )	-	1000	-
6.6(Joints in messenger conductor )	-	1000	-
6.6(Direction of outer layer)	-	1000	-
7.1(Insulation)	-	1000	-
7.2( Thickness of insulation)	-	1000	-
7.3(Tolerance on thickness of insulation )	-	1000	-
7.4(Aplication of the insulation )	-	1000	-
7.5(Colour of the insulation )	-	1000	-
8.1(Core identification)	-	1000	-
8.2(Core identification)	-	1000	-
8.3(Identification by other means)	-	1000	-
9.1(Assembly (Laying up))	-	1000	-
9.2(Assembly (Laying up))	-	1000	-
9.3(Direction of lay)	-	1000	-
10.1 a) i)(Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-	1000	-
10.1 a) ii)(Wrapping test - 10810: Part 3)	-	1000	-
10.1 a) iii)(Resistance test - IS10810: Part 5)	-	2000	-
10.1 b) i)(Test on messenger conductor: Breaking load - IS 10810: Part 2)	-	2000	-
10.1 b) ii)(Test on messenger conductor: Elongation test - Cl 11.3)	-	2000	-
10.1 b) iii)(Test on messenger conductor: Resistance test - IS 10810: Part 5)	-	2000	-
10.1 c) i)(Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-	2000	-
10.1 c) i)(Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-	2000	-
10.1 c) ii)(Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-	5000	-
10.1 c) ii)(Ageing in air oven : Elongation variation- IS 10810: Part 11)	-	5000	-
10.1 c) iii)(Hot set test: Elongation under load - IS 10810: Part 30)	-	2000	-
10.1 c) iii)(Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-	2000	-
10.1 c) iv)(Shrinkage test : Shrinkage - 10810:Part 12)	-	2000	-
10.1 c) iv)(Shrinkage test : Crack Observed - 10810:Part 12)	-	2000	-
10.1 c) v)(Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-	5000	-
10.1 d) i)(Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-	2000	-
10.1 d) i)(Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-	2000	-
10.1 d) ii)(Melt flow index- IS 10810: Part 23)	-	2000	-
10.1 d) iv)(Vicat softening point -IS 10810: Part 22)	-	2000	-
10.1 d) v)(Environmental stress cracking -IS 10810:Part29)	-	2000	-
10.1 f)(Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-	2000	-
10.1 f)(Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-	2000	-
10.1 g)(High voltage test - IS10810:Part 45)	-	2000	-
11.4(Bending Test on the Completed Cable ( Optional) )	-	2000	-
11.4(Bending Test on the Completed Cable ( Optional))	-	2000	-
10.1 d) iii)(Carbon Black Content)	-	2000	-
6.1(Construction of phase conductor)	-	1000	-
6.1(Number of wires (phase conductor))	-	1000	-
6.1(Construction of Street Lighting conductor)	-	1000	-
6.1(Number of wires (Street Lighting conductor))	-	1000	-
12.1(Manufacturer's Identification)	-	1000	-
12.2(Cable Identification)	-	1000	-

01 Oct, 2029

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

27100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	0	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	0	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	0	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	0	-
6.1(MATERIALS : ARMGURING)	-	0	-
6.2(MATERIALS : ARMGURING)	-	0	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	0	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	0	-
8.1(CONSTRUCTION : CONDUCTOR)	-	0	-
8.2(CONSTRUCTION : CONDUCTOR)	-	0	-
9.1(INSULATION )	-	0	-
9.2(INSULATION : Thickness of Insulation)	-	100	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	100	-
9.4(INSULATION : Application of Insulation)	-	0	-
10.1(CORE IDENTIFICATION)	-	0	-
10.2(CORE IDENTIFICATION)	-	0	-
10.3(CORE IDENTIFICATION)	-	0	-
10.3.1(Arrangement of Marking)	-	0	-
11.1(LAYING UP OF CORES)	-	0	-
11.2(LAYING UP OF CORES)	-	0	-
12.1(INNER SHEATH)	-	0	-
12.2(INNER SHEATH)	-	0	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	100	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	100	-
13.1.1(ARMOURING : Application)	-	0	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(ARMOURING : Direction of lay )	-	0	-
13.1.4(ARMOURING : Application)	-	0	-
13.2(ARMOURING : Type of Armour)	-	0	-
13.2.1(ARMOURING : Type of Armour)	-	0	-
13.3(Armouring : Dimensions -Wire Diameter)	-	100	-
13.3(Armouring : Dimensions -Formed wire )	-	100	-
13.4(ARMOURING : Joints)	-	0	-
13.5.1(ARMOURING : Resistance)	-	100	-
13.5.2(ARMOURING : Resistance)	-	100	-
13.6 a)(ARMOURING: Tensile Strength)	-	100	-
13.6 b)(ARMOURING: Elongation )	-	100	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	100	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	100	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	100	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	100	-
13.6 g)(ARMOURING: Resistivity)	-	100	-
14.1(OUTER SHEATH)	-	0	-
14.2(OUTER SHEATH)	-	0	-
14.3(OUTER SHEATH : Colour )	-	0	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	100	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	100	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	100	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	100	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	100	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	100	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	500	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	500	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	500	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	500	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	500	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	500	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	1000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	1000	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	500	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	500	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	500	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	500	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	500	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	100	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	100	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	100	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	100	-
15.1 d)4)(Hot deformation : Insulation )	-	500	-
15.1 d)4)(Hot deformation : Sheath )	-	500	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	1000	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	1000	-
15.1 d)6)(Heat shock test- Insulation )	-	100	-
15.1 d)6)(Heat shock test- sheath )	-	100	-
15.1 d)7)(Thermal stability- insulation )	-	500	-
15.1 d)7)(Thermal stability- Sheath )	-	500	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	500	-
15.1 e)(Insulation resistance test : IR Constant )	-	500	-
15.1 f)(High voltage test ( water immersion test ))	-	1000	-
15.1 g)(High voltage test at room temperature)	-	500	-
15.1 g)(High voltage test at room temperature)	-	500	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	500	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	500	-
15.4 b)(Cold impact test- Insulation ( Optional test))	-	500	-
15.4 b)(Cold impact test- Sheath ( Optional test))	-	500	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	500	-
16.1(DETAILS OF TESTS : General)	-	0	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	0	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	0	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1000	-
16.4(Flammability Test)	-	100	-
16.5(Oxygen Index Test)	-	1000	-
16.6(Flame Retardance Test on Single Cables)	-	100	-
16.7(Flame Retardance Test on Bunched Cables)	-	3000	-
16.9(Test for Halogen Acid Gas Evolution)	-	1000	-
16.1(Temperature Index)	-	1000	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	0	-
17.2(IDENTIFICATION : Cable Identification)	-	0	-
17.2.1(IDENTIFICATION : Cable Identification)	-	0	-
17.3(IDENTIFICATION : Cable Code)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	0	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	0	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	0	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	0	-
16.4(Flammability Test- Un affected portion)	-	0	-
16.4(Flammability Test- Period of Burning)	-	0	-
9.3(Minimum Thickness of Reduce core insulation)	-	0	-
9.2(Thickness of Reduce core insulation)	-	0	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	0	-
Cl No. 16.10(Smoke density test)	-	500	-
Cl No. 16.8(Test for specific optical density of smoke)	-	0	-
Table 4(Copper purity test)	-	500	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Conductor, Number of wires.)	-	0	-
Cl.8(Flexibility class)	-	0	-
[(Cl.15), (d), 2](After ageing, Elongation of Sheath [Percentage])	-	0	-

01 Oct, 2029

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
13(Cable code)	-	0	-
11.2(Legibility)	-	0	-
11.1(Durability)	-	0	-
11(Identification)	-	0	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	2000	-
10.4(Flammability test- Unaffected portion)	-	500	-
10.4(Flammability test-Burning after flame removal)	-	0	-
table 1 e) 3) (IR constant- max. Temp)	-	500	-
table 1 e) 3) (IR constant- Room temp )	-	500	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	500	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	500	-
10.2(HV (room temperature))	-	500	-
10.1(HV (water immersion))	-	1000	-
10.1(HV (water immersion))	-	1000	-
10.8(Smoke density rating)	-	500	-
10.6(Halogen evolution)	-	500	-
10.7(Temperature index)	-	500	-
10.5(Oxygen index)	-	500	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	100	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	100	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	100	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	100	-
Table 1(Category Code)	-	0	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	100	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	100	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	100	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	100	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	100	-
Table 1 iii) d) 4)(Cracks Observed)	-	0	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	100	-
Table 1 iii) c) 4)(Cracks Observed)	-	0	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	100	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	500	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	500	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	500	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	500	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	100	-
Table 1 iii) d) 1)(Sheath -Tensile strength (Without ageing))	-	100	-
Table 1 iii) c) 3)(Elongation variation)	-	100	-
Table 1 iii) c) 3)(TS variation)	-	100	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	100	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	500	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	100	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	100	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	0	-
8.3(Thickness of Sheath)	-	100	-
5.2(Application )	-	0	-
5.3(Thickness of Insulation)	-	100	-
9.1(Ovality)	-	100	-
9(Overall dimensions)	-	100	-
10.11(Per sulphate test (for tinned Cu cable only))	-	500	-
4.2(Conductor resistance test)	-	500	-
4.1(Wrapping test (for Al))	-	100	-
4.1(Tensile test (for Al)- After Stranding)	-	100	-
4.1(Tensile test (for Al)-Before Stranding)	-	100	-
4.1(Annealing test (for copper))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	0	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	0	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	0	-
12(CONSTRUCTION Core Identification)	-	0	-
8.1(Sheath Material )	-	0	-
7(Binder Tape)	-	0	-
6.2(Filler)	-	0	-
6.1(Filler)	-	0	-
5.1(Insulation)	-	0	-
4.4(Joints in Conductor)	-	0	-
4.4(Joints in Conductor)	-	0	-
4.1(Conductor - Material)	-	0	-
4.1(Conductor - Material)	-	0	-
10.11(Persulphate Test )	-	500	-
12.0(Core identification)	-	0	-
4, IS 8130(Construction of conductor)	-	0	-
Table 2, IS 8130(No fo wire in a conductor)	-	0	-
8.3(Minimum thickness of Sheath)	-	100	-
8.3(Avarage thickness of Sheath)	-	100	-
5.3(Minimum thickness of insulation)	-	100	-
5.3(Avarage thickness of insulation)	-	100	-
Table 4(Copper purity test)	-	500	-
10.3(Spark test)	-	0	-
table 1, 4.2(insulation resistance test)	-	0	-
5.4(Mechanical properties before and after ageing)	-	0	-
10.3(Spark Test)	-	0	-
4.1(Material)	-	0	-
4.2(Electrical Resistance)	-	0	-
5(INSULATION)	-	0	-
6(FILLER)	-	0	-
7(BINDER TAPE)	-	0	-
8(SHEATH)	-	0	-
9(OVERALL DIMENSIONS)	-	100	-
10.1(High Voltage Test (Water Immersion Test))	-	0	-
10.2(High Voltage Test (at Room Temperature))	-	0	-
10.3(Spark Test)	-	0	-
10.4(Flammability Test)	-	0	-
10.5(Oxygen Index Test)	-	0	-
10.6(Test for Halogen Acid Gas Evolution)	-	0	-
10.7(Test for Temperature Index)	-	0	-
10.8(Smoke Density Rating)	-	0	-
10.9(Additional Ageing Test (for Cables for Outdoor Use)	-	0	-
10.1(Flex Test)	-	0	-
10.11(Persulphate Test)	-	0	-
11(IDENTIFICATION)	-	0	-
12(CORE IDENTIFICATION)	-	0	-
13(CABLE CODE)	-	0	-
15(PACKING AND MARKING)	-	0	-
16.1(Construction)	-	0	-
16.2(Tests)	-	0	-
17(SINGLE CORE NON-SHEATHED CABLES WITH FLEXIBLE CONDUCTOR FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
18(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH RIGID CONDUCTOR (CLASS 1 AND CLASS 2) FOR GENERAL PURPOSE ) FOR MAXIMUM CONDUCTOR TEMPERATURE (70°C OR 85°C))	-	0	-
19(SINGLE AND MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES/CORDS WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
20(MULTICORE CIRCULAR PVC INSULATED AND SHEATHED CABLES WITH FLEXIBLE CONDUCTOR (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
21(ARALLEL TWIN AND TWISTED TWIN FLEXIBLE PVC INSULATED UNSHEATHED CORDS (CLASS 5) FOR GENERAL PURPOSE (FOR MAXIMUM CONDUCTOR TEMPERATURE 70°C OR 85°C))	-	0	-
22(TWO AND THREE CORE FLAT CABLES WITH PVC INSULATION AND SHEATHED (CLASS 2 OR 5) FOR GENERAL PURPOSE( FOR MAXIMUM CONDUCTOR TEMPERA TURE 70°C OR 85°C))	-	0	-
(4.3 of IS 8130:2013)(Form of Conductor)	-	0	-
( 4.4.1 of IS 8130:2013)(Joints in Conductor)	-	0	-
(4.4.2 of IS 8130:2013)(Joints in Conductor Solid Conductors (Aluminium Conductors only))	-	0	-
(Cl.6.1.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(Cl.6.1.2 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-
(6.2.1 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	0	-
(6.2.2 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	0	-
(6.2.3 of IS 8130:2013)(Stranded Circular Non-compacted Conductors (Class 2))	-	0	-
(6.3.1 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	0	-
(6.3.2 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	0	-
(6.3.3 of IS 8130:2013)(Stranded Compacted Circular Conductors and Shaped Conductors (Class 2))	-	0	-
( 6.4.1 of IS 8130:2013)(Flexible Conductors (Class 5))	-	0	-
(6.4.2 of IS 8130:2013)(Flexible Conductors (Class 5))	-	0	-
( 6.4.3 of IS 8130:2013)(Flexible Conductors (Class 5))	-	0	-
Cl.19.1.4(Assembly of Cores)	-	0	-
Cl. 8.2(Application of Sheath)	-	0	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	0	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	0	-

01 Oct, 2029

-
-

Bureau of Indian Standards

The National Standards Body of India

Dynamic Test and Research Centre

House No. D-7, Kh. No. 6/21, Block-D, Rama Vihar, Village Mohammadpur Majri, Karala, New Delhi-110081, Delhi, North West, Delhi, 110081

9911092203 info@dtrclab.com

Scope List