BIS - LIMS (Laboratory Information Management System)

CIPET, Jaipur

SP-1298, Sitapura Industrial Area, Phase III,Tonk Road, JAIPUR-302 022, Jaipur, Jaipur, Rajasthan, 302022

9090968451 cipetjprtesting@gmail.com

Scope List

Reset

76 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

All size & class

28100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(CLASSIFICATION OF PIPES)	-	0	-
6.1.2(PVC Resin)	-	4100	VCM content= 3000 + K- Value: 1100
Cl-7.1(Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-	500	All dimensions
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	-
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	-
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	0	-
Cl- 7.2(Socket length (Take 4 reading & minimum will be reported))	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	-
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	-
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	0	-
8(SEALING RINGS)	-	0	-
9.1(PIPE ENDS)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	-
10.1(Colour)	-	0	-
10.1(Surface Finish)	-	0	-
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	700	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1200	Testing charges + specimen charges ( 700+500)
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	700	-
10.7(Sulphated Ash Content)	-	1200	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	5000	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	-
11.2(Resistance to External Blows at 0°C)	-	1500	Testing charges +Specimen ( 1000+500)
10.3(Effect on Water Test)	-	3000	-
7.1.4(Length)	-	0	-
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	0	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	0	-
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	0	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	0	-
10.7(Sulphated Ash Content)	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	0	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	0	-
11.2(Resistance to External Blows at 0°C)	-	0	Testing charges +Specimen ( 1100+300)
10.3(Effect on Water Test)	-	0	-
6.1.1(VCM Content)	-	0	-
7.2.1.2b(Maximum inner diameter of groove)	-	0	-
13.1(Marking)	-	0	-

21 Feb, 2029

-
-

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

All Size

57801.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Dimensions of pipe - i) Outside diameter)	-	1000	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	500	-
6(Visual Appearance)	-	500	-
7.1(Hydraulic Characteristics - Quality test)	-	4800	-
7.1(Hydraulic Characteristics - Acceptance test)	-	1600	-
7.2(Reversion Test)	-	1200	Testing + specimen charges ( 700+500)
7.3(Tensile Test- i) Tensile Strength)	-	1800	Testing + specimen charges ( 1300+500)
7.4(Fusion Compatibility Test- a) Quality test)	-	4800	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	1600	-
7.5(Density)	-	700	-
7.6(Melt Flow Rate)	-	1100	-
7.6(Melt Flow Rate)	-	1100	-
4.2(Carbon black- a)carbon content)	-	925	-
4.2(Carbon black- b) Dispersion of carbon black)	-	0	-
7.6(Melt now Rate (MFR))	-	0	-
7.5(Density)	-	700	-
7.4 Table-2(Fusion Compatibility Test)	-	0	-
7.3(Tensile Test)	-	0	-
7.2(Reversion Test)	-	0	-
7.1 Table -2(Hydraulic Characteristics)	-	0	-
6.1(VISUAL APPEARANCE)	-	0	-
5.1.2(Ovality)	-	0	-
5.1 table -1(DIMENSIONS OF PIPES)	-	1500	-
4.3(Anti-oxidant)	-	0	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1100	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	700	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1100	-
3(CLASSIFICATION OF PIPES)	-	0	-
4.1(Quick Coupled Male and Female Couplers)	-	850	-
4.1(Quick Coupled Male and Female Couplers)	-	0	-
4.1.3(Workmanship and appearance)	-	500	-
4.1.4(Holding attachments for coupler parts)	-	0	-
6.1.3(Weldability Test- a) Quality test)	-	1600	-
6.1.3(Weldability Test- b) Acceptance test)	-	1600	-
3(Quick Coupled pipes)	-	0	-
3(QUICK COUPLED PIPES)	-	0	-
4(QUICK COUPLED FITTINGS)	-	0	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	0	-
4.1 (b)(HDPE couplers —)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	925	-
4.1 .1.2.1(HDPE couplers)	-	0	-
4.1 .1.2.2(HDPE couplers)	-	0	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	0	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	0	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	0	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	0	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	0	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	0	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	0	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	0	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	0	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	0	-
6.1(Quick Coupled Pipes and Fittings)	-	0	-
6.1.1, 6.1.1.1(Leakage Test)	-	850	-
6.1.1, 6.1.1.1(Leakage Test)	-	0	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	850	-
6.1.2.2(Hydraulic Proof Test)	-	0	-
6.1.2.2(Hydraulic Proof Test)	-	0	-
6.1.3, 6.1.3.1(Weldability Test)	-	0	-
6.1.3.1.1(Weldability Test)	-	0	-
6.1.3.2(Quick coupled fittings)	-	0	-
6.2, 6.2.1(Quick Coupled Fittings)	-	0	-
7.2.1(Visual and Workmanship Requirement)	-	500	-
6.2 b(Material Identification - Male & Female Coupler)	-	1050	-
6.3.3(Material Identification - Insert Valve Coupler)	-	0	-
6.3.3(Material Identification - Insert Valve Coupler)	-	0	-
6.3.4()	-	0	-
6.3.5(Material Identification - Saddle)	-	0	-
6.3.5(Material Identification - Pipe Ends)	-	0	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	0	-
4.2(Metallic Couplers)	-	0	-
4.2(Metallic Couplers)	-	0	-
7.2.1(Leakage Test)	-	0	-
Cl.4.1.3(Den sity Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(Thermal Stabi lity)	-	0	-
Cl.4.1.3(Thermal Stabi lity)	-	2200	-
Cl.4.1.3, T-1(Volatile Matter)	-	700	-
Cl.4.1.3, T-1(Volatile Matter)	-	700	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	700	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.4(Carbon Black Content)	-	925	-
Cl.4.1.4(Carbon Black Content)	-	0	-
Cl.4.1.4(Carbon Black Content)	-	0	-
Cl.4.1.4(Carbon Black Di spersion)	-	700	-
Cl.4.1.4(Carbon Black Di spersion)	-	0	-
Cl.4.1.4(Carbon Black Di spersion)	-	0	-
Cl.5(Di men sion)	-	0	-
Cl.5.1.l(Outside Diameter)	-	1000	-
Cl.5.1.l(Outside Diameter)	-	0	-
Cl.6.2.L(Wall Thickness)	-	500	-
Cl.6.2.4(Workmanship and Appearance)	-	500	-
Cl.6.2.6(Rubber Ring Hardness)	-	500	-
Cl.6.2.6(Ageing Test)	-	4200	-
Cl.7.1.l(Visual Anneara nce)	-	500	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.2(Hydraulic Characteristic)	-	1600	-
Cl.7.1.2(Hydraulic Characteristic)	-	4800	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.3(Reversion Test)	-	1200	Testing + specimen charges ( 700+500)
Cl.7.1.3(Reversion Test)	-	0	-
Cl.7.1.4(Tensile Test)	-	1800	Testing + specimen charges ( 1300+500)
Cl.7.1.4(Tensile Test)	-	0	-
Cl.7.1.4(Tensile Test)	-	0	-
Cl.7.1.4(Elongation)	-	0	-
Cl.7.1.4(Elongation)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	1600	-
Cl.7.1.5(Fusion Compatibility)	-	4800	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.6(Corrected Density)	-	700	-
Cl.7.1.7(MFR Test)	-	1100	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	850	-
Cl.7.2.l(Leakage Test)	-	850	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.2(Cl.7.2.2)	-	0	-
Cl.7.2.3(Weld ability Test)	-	1600	-
Cl.7.2.3(Weld ability Test)	-	4800	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	500	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	500	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	1500	-
6.1(Thermal Stability (OIT))	-	2200	-
6.1(Volatile Matter)	-	700	-
6.1(Water content)	-	700	-
6.1(Tensile strength at Yield & Elongation at break)	-	1800	Testing + specimen charges ( 1300+500)
6.1(Carbon Black Content)	-	925	-
6.1(Carbon Black Dispersion)	-	700	-
6.2.1(Base Density x 2)	-	700	-
6.2.1(Melt Flow Index x 2)	-	1100	-
6.2.1(Thermal Stability (OIT) x 2)	-	0	-
6.2.1(Volatile Matter x 2)	-	0	-
6.2.1(Water content x 2)	-	0	-
6.2.1(Carbon Black Content x 2)	-	0	-
6.2.1(Carbon Black Dispersion x 2)	-	0	-
6.2.1(Wall thickness of male & female coupler)	-	0	-
6.2.4(Workmanship and appearance (Visual))	-	0	-
6.2.5(Holding attachment for coupler parts)	-	0	-
6.2.5(Material Composition (Chemical Analysis))	-	0	-
4.2.2(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	0	-
6.2.6(Material Identification (Chemical Analysis))	-	0	-
6.2.6(Color)	-	500	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	500	-
6.2.6(Ageing Charges for rubber ring)	-	4200	-
7.1.1(Visual appearance of pipes)	-	500	-
7.1.2(Hydraulic Characteristics)	-	0	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	1600	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	4800	-
7.1.3(Reversion)	-	1200	Testing + specimen charges ( 700+500)
7.1.4(Tensile strength & elongation)	-	1800	Testing + specimen charges ( 1300+500)
7.1.5(Fusion Compatibility test)	-	0	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	1600	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	4800	-
7.1.6(Corrected Density)	-	700	-
7.1.6(Base Density)	-	700	-
7.1.6(Carbon black Content)	-	925	-
7.1.7(Melt Flow Rate (MFR))	-	1100	-
7.2.1(Leakage test 1hour / 27°C)	-	0	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	0	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	0	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	0	-
8(Supply of pipe (Visual))	-	500	-
4.1.1 (Table-1)(Density)	-	700	-
4.1.1 (Table-1)(Melt Flow Index)	-	1100	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	2200	-
4.1.1 (Table-1)(Volatile Matter)	-	0	-
4.1.1 (Table-1)(Water content)	-	0	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	0	-
4.1.4(Carbon Black Content)	-	0	-
4.1.4(Carbon Black Dispersion)	-	0	-
4.1.1(Polyethylene material)	-	0	-
4.1.3, Table 1,(i)(Bass density)	-	0	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	0	-
4.1.3, Table 1,(iii)(Thermal stability)	-	0	-
4.1.3, Table 1,(iv)(Volatile matter)	-	0	-
4.1.3, Table 1,(v)(Water content)	-	0	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	0	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	0	-
4.1.4(The Carbon Content and Dispersion)	-	0	-
4.1.5(Carbon Black Specification)	-	0	-
4.1.6(Antioxidant)	-	0	-
4.1.7(Rework Material)	-	0	-
4.2(Metallic Couplers)	-	0	-
5.1, Table 1,(i)(Plain pipes)	-	0	-
5.1, Table 1,(ii)(90° Bends and tee)	-	0	-
5.1, Table 1,(iii)(Base pipe )	-	0	-
5.1, Table 1,(iv)(PCN)	-	0	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	0	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	0	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	0	-
7.1.1(Visual Appearance and Workmanship)	-	0	-
7.1.2(Hydraulic Performance Characteristic)	-	0	-
7.1.3(Reversion Test)	-	0	-
7.1.4(Tensile Test)	-	0	-
7.1.5(Fusion Compatibility Test)	-	0	-
7.1.6(Corrected Density)	-	0	-
7.1.7(Melt flow rate)	-	0	-
7.2.1(Leakage Test)	-	0	-
7.2.2(Hydraulic Proof Test)	-	0	-
7.2.3(Weldability Test)	-	0	-
7.3(Quick Couple Fitting)	-	0	-
10(Marking)	-	0	-
5.1.2(Squareness)	-	0	-
Cl 6.3.5, Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten)(Table 5 Dimension of Quick Coupled Sprinkler Saddles (Foot Batten))	-	0	-
7.3(Tensile Test - ii)Elongation at Break)	-	0	-

21 Feb, 2029

-
-

IS 11744 (2020)

Phosphorous Pentachloride, Technical - Specification ( First Revision )

Phosphorous Pentachloride- Specification

11100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Description)	-	500	-
Table-1(Phosphorous pentachloride ( as PCl 5),)	-	2200	-
Table-1(Bulk density)	-	1500	-
Table-1(Sulphate)	-	2500	-
Table-1(Iron)	-	2200	-
Table-1(Lead)	-	2200	-

21 Feb, 2029

-
-

IS 5295 (2023)

Ethylene Glycol - Specification (Third Revision)

Ethylene Glycol - Specification

25500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1("Description IS 5295 : 2023 ")	-	500	-
4.2Table 1 (i)("Colour IS 5295 : 2023 ")	-	1500	-
4.2Table 1 (ii)("Relative density at 20 °C/20 °C (IS 1448 (Part 167)")	-	1000	-
4.2Table 1 (iii)("Distillation range at 760 mmHg IS 5298")	-	2200	-
4.2Table 1 (iii)(a) Initial boiling point)	-	0	-
4.2Table 1 (iii)(b) The temperature at which 95 ml of material shall distil)	-	0	-
4.2Table 1 (iv)("Moisture content 1448 (Part 175) / 1448(Part 182) ")	-	1500	-
4.2Table 1 (v)("Acidity (as acetic acid) IS 5295 : 2023 ")	-	1500	-
4.2Table 1 (vi)("Ultra-Violet transmittance in 1 cm cell at IS 5295 : 2023 ")	-	2200	-
4.2Table 1 (vi)(a) 220 nm)	-	0	-
4.2Table 1 (vi)(b) 275 nm)	-	0	-
4.2Table 1 (vi)(c) 350 nm)	-	0	-
4.2Table 1 (vii)("Freezing point of equal volumes of material and water IS 5295 : 2023 ")	-	2200	-
4.2Table 1 (viii)("Iron content IS 5295 : 2023 ")	-	2200	-
4.2Table 1 (ix)("Chlorides content IS 5295 : 2023 ")	-	2000	-
4.2Table 1 (x)("Purity IS 5295 : 2023 ")	-	3200	-
4.2Table 1 (xi)("Diethylene glycol content IS 5295 : 2023 ")	-	3000	-
4.2Table 1 (xii)("Aldehyde (as HCHO) IS 5295 : 2023 ")	-	2000	-
4.1(Material shall be colourless)	-	0	-
4.2-Table 1-i)(Colour, Pt-Co, Max)	-	0	-
4.2-Table 1-ii)(Relative density1) at 20 °C/20 °C)	-	0	-
4.2-Table 1-iii)(Distillation range at 760 mmHg: a) Initial boiling point, °C Min b) The temperature at which 95 ml of material shall distil, °C, Max)	-	0	-
4.2-Table 1-iv)(Moisture content, percent by mass, Max)	-	0	-
4.2-Table 1-v)(Acidity (as acetic acid), ppm, Max)	-	0	-
4.2-Table 1-vi)(Ultra-Violet transmittance in 1 cm cell at a) 220 nm, Min b) 275 nm, Min c) 350 nm, Min )	-	0	-
4.2-Table 1-vii)(Freezing point of equal volumes of material and water, Max)	-	0	-
4.2-Table 1-viii)(Iron content, ppm, Max)	-	0	-
4.2-Table 1-ix)(Chlorides content (as Cl), ppm, Max)	-	0	-
4.2-Table 1-x)(Purity, percent, Min)	-	0	-
4.2-Table 1-xi)(Diethylene glycol content, ppm, Max)	-	0	-
4.2-Table 1-xii)(Aldehyde (as HCHO), ppm, Max)	-	0	-
6.1(Packing)	-	500	-
6.2(Marking)	-	0	-
4.1("Description IS 5295 : 2023 ")	-	0	-
4.2Table 1 (i)("Colour IS 5295 : 2023 ")	-	0	-
4.2Table 1 (ii)("Relative density at 20 °C/20 °C (IS 1448 (Part 167)")	-	0	-
4.2Table 1 (iii)("Distillation range at 760 mmHg IS 5298")	-	0	-
4.2Table 1 (iii)(a) Initial boiling point)	-	0	-
4.2Table 1 (iii)(b) The temperature at which 95 ml of material shall distil)	-	0	-
4.2Table 1 (iv)("Moisture content 1448 (Part 175) / 1448(Part 182) ")	-	0	-
4.2Table 1 (v)("Acidity (as acetic acid) IS 5295 : 2023 ")	-	0	-
4.2Table 1 (vi)("Ultra-Violet transmittance in 1 cm cell at IS 5295 : 2023 ")	-	0	-
4.2Table 1 (vi)(a) 220 nm)	-	0	-
4.2Table 1 (vi)(b) 275 nm)	-	0	-
4.2Table 1 (vi)(c) 350 nm)	-	0	-
4.2Table 1 (vii)("Freezing point of equal volumes of material and water IS 5295 : 2023 ")	-	0	-
4.2Table 1 (viii)("Iron content IS 5295 : 2023 ")	-	0	-
4.2Table 1 (ix)("Chlorides content IS 5295 : 2023 ")	-	0	-
4.2Table 1 (x)("Purity IS 5295 : 2023 ")	-	0	-
4.2Table 1 (xi)("Diethylene glycol content IS 5295 : 2023 ")	-	0	-
4.2Table 1 (xii)("Aldehyde (as HCHO) IS 5295 : 2023 ")	-	0	-
4.1(Material shall be colourless)	-	0	-
4.2-Table 1-i)(Colour, Pt-Co, Max)	-	0	-
4.2-Table 1-ii)(Relative density1) at 20 °C/20 °C)	-	0	-
4.2-Table 1-iii)(Distillation range at 760 mmHg: a) Initial boiling point, °C Min b) The temperature at which 95 ml of material shall distil, °C, Max)	-	0	-
4.2-Table 1-iv)(Moisture content, percent by mass, Max)	-	0	-
4.2-Table 1-v)(Acidity (as acetic acid), ppm, Max)	-	0	-
4.2-Table 1-vi)(Ultra-Violet transmittance in 1 cm cell at a) 220 nm, Min b) 275 nm, Min c) 350 nm, Min )	-	0	-
4.2-Table 1-vii)(Freezing point of equal volumes of material and water, Max)	-	0	-
4.2-Table 1-viii)(Iron content, ppm, Max)	-	0	-
4.2-Table 1-ix)(Chlorides content (as Cl), ppm, Max)	-	0	-
4.2-Table 1-x)(Purity, percent, Min)	-	0	-
4.2-Table 1-xi)(Diethylene glycol content, ppm, Max)	-	0	-
4.2-Table 1-xii)(Aldehyde (as HCHO), ppm, Max)	-	0	-
6.1(Packing)	-	0	-
6.2(Marking)	-	0	-

21 Feb, 2029

-
-

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

All

41425 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1325	Testing charges + Specimen charges (700+625)
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2200	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	700	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	700	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	700	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	925	-
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	900	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	700	-
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	3000	-
5.2.1.1, T2(Compound ash content - Any Method)	-	1200	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	700	-
5.3(Density of Higher olefin - IS 7328:2020)	-	700	-
5.3(Olefin Constituents- 14333-2022)	-	0	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3(Ash content- Any Method)	-	0	-
5.3(Toluene extract - Any Method)	-	0	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	-
5.3(Carbon black particle size - Any Method)	-	0	-
5.4(Antioxidant - Any Method)	-	0	-
6(Pipe Description - IS 14333-2022)	-	0	-
6.2(Colour- IS 14333-2022)	-	500	-
7.1(Visual Appearance- IS 14333-2022)	-	500	-
7.2(Length- IS 14333-2022)	-	500	-
7.3(Coiling- IS 14333-2022)	-	0	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	500	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	4000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	4800	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	11000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	1200	Testing+ specimen charges (700+500)
8.3(Carbon black content- IS 2530-1963)	-	925	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	700	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1100	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2200	-
8.6(Density-IS 7328:2020)	-	700	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1800	Testing+ specimen charges (1300+500)
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	1800	Testing+ specimen charges (1300+500)
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	6000	Testing+ specimen charges (5500+500)
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	0	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	0	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	0	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	0	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	0	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	0	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	0	-
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	0	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	0	-
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	0	-
5.2.1.1, T2(Compound ash content - Any Method)	-	0	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	0	-
5.3(Density of Higher olefin - IS 7328:2020)	-	0	-
5.3(Olefin Constituents- 14333-2022)	-	0	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3(Ash content- Any Method)	-	0	-
5.3(Toluene extract - Any Method)	-	0	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	-
5.3(Carbon black particle size - Any Method)	-	0	-
5.4(Antioxidant - Any Method)	-	0	-
6(Pipe Description - IS 14333-2022)	-	0	-
6.2(Colour- IS 14333-2022)	-	0	-
7.1(Visual Appearance- IS 14333-2022)	-	0	-
7.2(Length- IS 14333-2022)	-	0	-
7.3(Coiling- IS 14333-2022)	-	0	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	0	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	0	-
8.3(Carbon black content- IS 2530-1963)	-	0	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	0	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	0	-
8.6(Density-IS 7328:2020)	-	0	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	0	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	0	-

21 Feb, 2029

-
-

IS 2080 (2021)

Specification for stabilized hydrogen peroxide First Revision

Stabilized Hydrogen Peroxide-Specification (Grade 5 & 6)

13100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Description - IS 2080:2021)	-	500	-
4.2(Strength - IS 2080:2021)	-	2200	-
4.3(Stability - IS 2080:2021)	-	2200	-
4.4/Table 1 (i)(Acidity (as H2SO4) - IS 2080:2021)	-	1500	-
4.4/Table 1 (ii)(Residue on Evaporation - IS 2080:2021)	-	1200	-
4.4/Table 1 (iii)(Residue on Ignition - IS 2080:2021)	-	1500	-
4.4/Table 1 (iv)(Iron (as Fe) - IS 2080:2021)	-	4000	-
4.4/Table 1 (v)(Copper (as Cu) - IS 2080:2021)	-	0	-
4.4/Table 1 (vi)(Lead (as Pb) - IS 2080:2021)	-	0	-
4.4/Table 1 (vii)(Arsenic (as As2O3) - IS 2080:2021)	-	0	-
5.1(Packing)	-	0	-
5.2(Marking)	-	0	-
Annex C(Stability)	-	0	-
Cl-4.1(Description/as per cl 4.1)	-	0	-
cl-4.2(Strength/as per annex-A or annex C-9)	-	0	-
cl-4.4, table 1, sl.no. (i)(Acidity (as H2so4) / as per annex c (C-1))	-	0	-
cl-4.4, table 1, sl.no. (ii)(Residue on evaporation/ as per annex c (C-2))	-	0	-
cl-4.4, table 1, sl.no. (iii)(residue on ignition as per annex c (C-3))	-	0	-
cl-4.4, table 1, sl.no. (iv)(Iron as (fe)/ as per annex c (C-4 and C-8))	-	0	-
cl-4.4, table 1, sl.no. (v)(Copper as (Cu)/ as per annex c (C-5 and C-8))	-	0	-
cl-4.4, table 1, sl.no. (vi)(Lead as (Pb)/ as per annex c (C-6 and C-8))	-	0	-
cl-4.4, table 1, sl.no. (vii)(Arsenic as (As203)/ as per annex c (C-7 and C-8))	-	0	-
4.1(Description - IS 2080:2021)	-	0	-
4.2(Strength - IS 2080:2021)	-	0	-
4.3(Stability - IS 2080:2021)	-	0	-
4.4/Table 1 (i)(Acidity (as H2SO4) - IS 2080:2021)	-	0	-
4.4/Table 1 (ii)(Residue on Evaporation - IS 2080:2021)	-	0	-
4.4/Table 1 (iii)(Residue on Ignition - IS 2080:2021)	-	0	-
4.4/Table 1 (iv)(Iron (as Fe) - IS 2080:2021)	-	0	-
4.4/Table 1 (v)(Copper (as Cu) - IS 2080:2021)	-	0	-
4.4/Table 1 (vi)(Lead (as Pb) - IS 2080:2021)	-	0	-
4.4/Table 1 (vii)(Arsenic (as As2O3) - IS 2080:2021)	-	0	-
5.1(Packing)	-	0	-
5.2(Marking)	-	0	-
Annex C(Stability)	-	0	-
Cl-4.1(Description/as per cl 4.1)	-	0	-
cl-4.2(Strength/as per annex-A or annex C-9)	-	0	-
cl-4.4, table 1, sl.no. (i)(Acidity (as H2so4) / as per annex c (C-1))	-	0	-
cl-4.4, table 1, sl.no. (ii)(Residue on evaporation/ as per annex c (C-2))	-	0	-
cl-4.4, table 1, sl.no. (iii)(residue on ignition as per annex c (C-3))	-	0	-
cl-4.4, table 1, sl.no. (iv)(Iron as (fe)/ as per annex c (C-4 and C-8))	-	0	-
cl-4.4, table 1, sl.no. (v)(Copper as (Cu)/ as per annex c (C-5 and C-8))	-	0	-
cl-4.4, table 1, sl.no. (vi)(Lead as (Pb)/ as per annex c (C-6 and C-8))	-	0	-
cl-4.4, table 1, sl.no. (vii)(Arsenic as (As203)/ as per annex c (C-7 and C-8))	-	0	-

21 Feb, 2029

-
-

IS 8058 (2018)

Pyridine - Specification (First Revision)

PYRIDINE-Technical specification

23550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.4 - Table 1 - Sl No - xi(Colour, HU (Pt-Co scale) - IS 8768)	-	1500	-
4.4 - Table 1 - Sl No - x(Moisture content - Annex L)	-	1500	-
4.4 - Table 1 - Sl No - ix(Sulphates (as SO4) - Annex K)	-	2000	-
4.4 - Table 1 - Sl No - viii(Oxidizable substances - Annex J)	-	2000	-
4.4 - Table 1 - Sl No - vii(Copper (as Cu) - Annex H)	-	2000	-
4.4 - Table 1 - Sl No - vi(Chlorides (as Cl) - Annex G)	-	2000	-
4.4 - Table 1 - Sl No - v(Ammonium compounds (as NH4) - Annex E)	-	2000	-
4.4 - Table 1 - Sl No - iv(Residue on evaporation - Annex D)	-	1200	-
4.4 - Table 1 - Sl No - iii(Boiling range at 760 mm Hg - Annex C)	-	1200	-
4.4 - Table 1 - Sl No - ii(Pyridine content - Annex B)	-	3200	-
4.4 - Table 1 - Sl No - i(Relative density at 250C/250C - Annex A)	-	1000	-
4.3(Identity and Purity - (Annex B))	-	3200	-
4.2(Solubility)	-	0	-
4.1(Description)	-	750	-

21 Feb, 2029

-
-

IS 695 (2020)

Acetic Acid — Specification ( Fourth Revision )

Actic Acid- technical specification

23650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3 - Table 1 - Sl No - xiv(Water content - IS 2362)	-	1500	-
4.3 - Table 1 - Sl No - xiii( Oxidizable impurities - Annex A 11)	-	1500	-
4.3 - Table 1 - Sl No - xii(Acetaldehyde (CH3CHO) - Annex A 10)	-	2000	-
4.3 - Table 1 - Sl No - xi(Formic acid (HCOOH)- Annex A 9)	-	2000	-
4.3 - Table 1 - Sl No - x(Heavy metals [(including iron) calculated as Pb] - Annex A 8)	-	2000	-
4.3 - Table 1 - Sl No - ix(Sulphate (as SO4) - Annex A 7)	-	2000	-
4.3 - Table 1 - Sl No - viii(Iron (as Fe) - Annex A 6)	-	2000	-
4.3 - Table 1 - Sl No - vii(Chloride (as Cl) - Annex A 5)	-	2000	-
4.3 - Table 1 - Sl No - vi(Residue on evaporation - Annex A 4)	-	1200	-
4.3 - Table 1 - Sl No - v(Crystallizing point - Annex A 3)	-	2200	-
4.3 - Table 1 - Sl No - iv(Acetic acid content (CH3COOH) - Annex A2)	-	2000	-
4.3 - Table 1 - Sl No - iii(Colour - IS 8768)	-	1500	-
4.3 - Table 1 - Sl No - ii(Relative density at 27/27 ℃ - Cl 6 of IS 82)	-	1000	-
4.3 - Table 1 - Sl No - i(Solubility in water - Annex A 1)	-	750	-
4.2.2(Description)	-	0	-
4.1(Description)	-	0	-
4.4(Arsenic (as As))	-	1000	-

21 Feb, 2029

-
-

IS 170 (2020)

Acetone — Specification ( Fifth Revision )

Acetone- Technical Specification

22350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl No 3.1( Description)	-	0	-
Cl No 3.2(Miscibility with Water)	-	500	-
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (i) ](Purity)	-	3200	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (ii) ] ref to IS 8768(Colour)	-	1500	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (iii) ] ref to 6 of IS 82(Relative density, at 27/27 °C)	-	1000	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (iv) ] IS 1448 (Part 18) with the thermometer containing to the requirements given to Annex B(*Distillation range)	-	2200	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (v) ] ref to IS 2362(Water content)	-	1200	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (vi) ] ref to 8 of IS 82(Residue on evaporation)	-	1200	-
Cl 3.3 and 6.1 ANNEX C [ Table 1, Sl No. (vii) ](Acidity (as CH3COOH),)	-	1500	-
Cl 3.3 and 6.1 ANNEX D [ Table 1, Sl No. (viii) ](Alkalinity)	-	1200	-
Cl 3.3 and 6.1 ANNEX E [ Table 1, Sl No. (ix) ](Permanganate test)	-	1200	-
Cl 3.3 and 6.1 ANNEX F [ Table 1, Sl No. (x) ](Alcoholic impurities)	-	1000	-
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (xi) ](Benzene content)	-	3200	-
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (xii) ](Methanol content)	-	3200	-
3.1(Description)	-	0	-
3.2(Miscibility with Water)	-	0	-
4.1(Packing)	-	0	-
4.2(Marking)	-	500	-
3.3 & 6.1 - Table -1, Sl no. 1(Purity %, Annex A)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 2(Colour, Pt-Co scale, IS 8768)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 3(Relative density, 6 of IS 82)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 4(Distillation range, IS 1448-Part 18)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 5(Water content, %, IS 2362)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 6(Residue on evaporation, mg/ 100 ml, 8 of IS 82)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 7(Acidity, g/100 ml, Annex C)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 8(Alkalinity, Annex D)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 9(Permanganate test, minutes, Annex E)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 10(Alcoholic impurities, Annex F)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 11(Benzene content mg/kg, Annex A)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 12(Methanol content mg/kg, Annex A)	-	0	-
Cl No 3.1( Description)	-	0	-
Cl No 3.2(Miscibility with Water)	-	0	-
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (i) ](Purity)	-	0	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (ii) ] ref to IS 8768(Colour)	-	0	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (iii) ] ref to 6 of IS 82(Relative density, at 27/27 °C)	-	0	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (iv) ] IS 1448 (Part 18) with the thermometer containing to the requirements given to Annex B(*Distillation range)	-	0	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (v) ] ref to IS 2362(Water content)	-	0	-
Cl 3.3 and 6.1 [ Table 1, Sl No. (vi) ] ref to 8 of IS 82(Residue on evaporation)	-	0	-
Cl 3.3 and 6.1 ANNEX C [ Table 1, Sl No. (vii) ](Acidity (as CH3COOH),)	-	0	-
Cl 3.3 and 6.1 ANNEX D [ Table 1, Sl No. (viii) ](Alkalinity)	-	0	-
Cl 3.3 and 6.1 ANNEX E [ Table 1, Sl No. (ix) ](Permanganate test)	-	0	-
Cl 3.3 and 6.1 ANNEX F [ Table 1, Sl No. (x) ](Alcoholic impurities)	-	0	-
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (xi) ](Benzene content)	-	0	-
Cl 3.3 and 6.1 ANNEX A [ Table 1, Sl No. (xii) ](Methanol content)	-	0	-
3.1(Description)	-	0	-
3.2(Miscibility with Water)	-	0	-
4.1(Packing)	-	0	-
4.2(Marking)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 1(Purity %, Annex A)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 2(Colour, Pt-Co scale, IS 8768)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 3(Relative density, 6 of IS 82)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 4(Distillation range, IS 1448-Part 18)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 5(Water content, %, IS 2362)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 6(Residue on evaporation, mg/ 100 ml, 8 of IS 82)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 7(Acidity, g/100 ml, Annex C)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 8(Alkalinity, Annex D)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 9(Permanganate test, minutes, Annex E)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 10(Alcoholic impurities, Annex F)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 11(Benzene content mg/kg, Annex A)	-	0	-
3.3 & 6.1 - Table -1, Sl no. 12(Methanol content mg/kg, Annex A)	-	0	-

21 Feb, 2029

-
-

IS 16709 (2017)

Textiles - Polypropylene (PP) woven, laminated, block bottom valve sacks for packaging of 50 kg cement - Specification

All

26800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Sack Length)	-	500	-
4.1.2(Sack Width)	-	0	-
4.1.3(Top Closure Width and Bottom Closure Width)	-	500	-
4.1.4(Patch Length)	-	500	-
4.1.5(Patch Height)	-	0	-
4.1.6(Length of Valve)	-	500	-
4.1.7(Width of Valve Sleeve)	-	0	-
4.1.8(Length of Valve Sleeve)	-	0	-
5.1(Raw Material)	-	2000	-
5.2(Fabric)	-	10600	Fabric Test charges
5.2(Tape density and width)	-	700	-
5.4(Lamination for PP)	-	2550	-
5.4(Lamination for LDPE)	-	2550.0	Lamination test charges
6.1(Mass of Bale)	-	500	-
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	2700.0	Avg. breaking strength of Fabric & elongation (min) length wise & width wise
6.2.2(Weld Strength of Top and Bottom Closures)	-	1100	-
6.3(Drop Impact Testing of Filled Sacks)	-	1100	-
6.4(Ash Content)	-	1200	-
6.5(Air Permeability)	-	1100	-
8(Atomspheric Conditions for Conditioning and Testing)	-	0	-
Cl-5.6(Capacity)	-	500	-
Cl- 6.6, Table.-1 (ii)(Ends per dm)	-	500	-
Cl-6.6, Table-1 (iii)(Picks per dm)	-	500	-
Cl.6.6, Table-1 (vii)(Elongation at break of fabric)	-	0	-

21 Feb, 2029

-
-

IS 2833 (2019)

Aniline, technical - Specification (Second Revision)

Aniline, Technical - Specification

16300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.2.1(Description)	-	1000	Include packing and marking charges also
Cl.2.2.1(Relative Density at 27/27 0C)	-	1000	-
Cl.2.2.2(Crystallizing Point)	-	2200	-
Cl.2.2.4(Assay, percent by Nitrite value)	-	2000	-
Cl.2.2.5(Nitrobenzene content by GC, ppm)	-	3200	-
Cl.2.2.3(Distillation Range)	-	2200	-
Cl.2.2.4(Assay, percent by GC)	-	3200	-
Cl.2.2.6(Moisture content, percent by mass)	-	1500	-
Cl.2.1(Description)	-	0	-
Cl.2.2.1(Relative Density at 27/27 0C)	-	0	-
Cl.2.2.2(Crystallizing Point)	-	0	-
Cl.2.2.4(Assay, percent by Nitrite value)	-	0	-
Cl.2.2.5(Nitrobenzene content by GC, ppm)	-	0	-
Cl.2.2.3(Distillation Range)	-	0	-
Cl.2.2.4(Assay, percent by GC)	-	0	-
Cl.2.2.6(Moisture content, percent by mass)	-	0	-

21 Feb, 2029

-
-

IS 252 (2013)

Caustic soda - Specification (Fourth Revision)

14450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Form and Description)	-	500	-
Cl. 3.3 and 3.4(Table 1, S. no i)(Sodium carbonate (as Na2CO3), percent by mass)	-	1200	-
Cl. 3.3 and 3.4(Table 1, S. no ii)(Sodium hydroxide (as NaOH), percent by mass)	-	1500	-
Cl. 3.3 and 3.4(Table 1, S. no iii)(Chlorides (as Cl– ), percent by mass)	-	1500	-
Cl. 3.3 and 3.4(Table 1, S. no iv)(Sulphates (as SO4), percent by mass)	-	1000	-
Cl. 3.3 and 3.4(Table 1, S. no v)(Silicates (as SiO2), percent by mass)	-	1000	-
Cl. 3.3 and 3.4(Table 1, S. no vi)(Iron (as Fe))	-	4000	single test charges for clause no.3.3 and 3.4 for iron, copper, manganese, mercury
Cl. 3.3 and 3.4(Table 1, S. no vii)(Copper)	-	0	single test charges for clause no.3.3 and 3.4 for iron, copper, manganese, mercury
Cl. 3.3 and 3.4(Table 1, S. no viii)(Manganese)	-	0	single test charges for clause no.3.3 and 3.4 for iron, copper, manganese, mercury
Cl. 3.3 and 3.4(Table 1, S. no ix)(Chlorates and per-chlorates)	-	1500	-
Cl. 3.3 and 3.4(Table 1, S. no x)(Matter insoluble water, percent by mass)	-	750	-
Cl. 3.3 and 3.4(Table 1, S. no xi)(Total mercury)	-	0	single test charges for clause no.3.3 and 3.4 for iron, copper, manganese, mercury
Cl. 3.3 and 3.4(Table 1, S. no xii)(Sodium hydroxide)	-	1500	-
5.2(Marking)	-	0	-
Cl-3.2(Relative Density of Caustic Soda Lye)	-	0	-
Cl-3.2(Relative Density of Caustic Soda Lye)	-	0	-

21 Feb, 2029

-
-

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

All

16100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	5275	Material Identification + Toluene extract + Maximum volatile content + Density (Optional)+Melt flow rate(Optional) ( 1050+1100+700+700+625+1100)=5275.00
Cl-4.2(Carbon content of finished PE lateral pipe)	-	1625.0	CBC+CBD ( 925+700)=1625.00
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	500	-
Cl-6.0(Visual Appearance)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	3000	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	1000	-
Cl-7.2(Reversion Test)	-	1200	Test charges+ specimen preparation (700+500)
Cl-7.3(Tensile Test)	-	1800.0	Test charges+ specimen preparation (1300+500)
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1200	-
Cl-8.0(Supply of pipes)	-	0	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
Cl-11(Marking)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.1 & Table 2(Hydraulic Characteristics)	-	0	-
7.2(Reversion Test)	-	0	-
7.3(Tensile Strength)	-	0	-
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	0	-
4.2(a)(Carbon Black Content-IS 2530)	-	0	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	0	-

21 Feb, 2029

-
-

IS 17399 (2020)

Textiles - Polypropylene ( PP )/ High Density Polyethylene ( HDPE ) Laminated Woven Sacks for Mail Sorting, Storage, Transport and Distribution - Specification

All

34505 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE - Raw Materials)	-	1050	-
5.2(MANUFACTURE - Fabric for PP tapes & for HDPE tapes)	-	70350.00	Fabric
5.2- Table 1- i)("REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm")	-	1500	a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm
5.2- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	500	-
5.2- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	500	-
5.2- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	500	-
5.2- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf) a) Lengthwise b) Widthwise)	-	2700	Testing Charges+ specimen ( 2200+500)
5.2- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min, N2), (kgf))	-	1100	-
5.2- Table 1- vii)("REQUIREMENTS - Elongation at break of fabric, percent: a) Lengthwise b) Widthwise")	-	0	-
5.2- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	1200	-
5.3(Lamination)	-	2050	Mass of lamination film Total Mass of Laminated woven fabric Material Identification of lamination
5.4(Sack Fabrication)	-	1500	Sacks Construction Gromet construction & dimensions
5.5(Capacity)	-	500	-
6.1- Table 1- i)(REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm)	-	0	-
6.1- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	0	-
6.1- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	0	-
6.1- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	0	-
6.1- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf))	-	0	-
6.1- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min)	-	0	-
6.1- Table 1- vii)(REQUIREMENTS - Elongation at break of fabric, percent a) Lengthwise b) Widthwise)	-	0	-
6.1- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	0	-
6.4(UV Resistance Test)	-	10180	UV exposure for 192 hrs.
7(PRINTING, PACKAGING AND MARKING)	-	0	-
8(ATMOSPHERIC CONDITIONS FOR SAMPLE CONDITIONING AND TESTING)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 5.4(Sack Fabrication)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-

21 Feb, 2029

-
-

IS 18482 (2023)

Textiles - Sandwich extrusion laminated polypropylene PP woven sacks for packaging bulk commodities - Specification

All

26230 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Sack Type)	-	0	-
5.2.1(Fabric)	-	0	-
5.2.2(Linear density of tapes)	-	500	-
5.2.4(Unlaminated fabric mass)	-	0	-
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	500	-
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	0	-
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	0	-
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	0	-
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	0	-
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	0	-
5.4.1(Sack)	-	2000	Material Identification
5.4.1.1(Centre seam)	-	1000	-
5.4.1.2(Bottom seam)	-	0	-
5.4.2(Sack)	-	500	-
5.4.3(Sack)	-	0	-
5.4.5(Liner)	-	3000	Liner Identification+Dimension+visual (2000+500+500)
6.1.1, Table 1(Inside length)	-	500	Dimension (Inside length+ Width)
6.1.1, Table 1(Inside width)	-	0	-
6.1.1, Table 1(Gusset width)	-	0	-
6.1.1, Table 1(Warp per dm)	-	500	-
6.1.1, Table 1(Weft per dm)	-	0	-
6.1.1, Table 1(Mass of laminated fabric)	-	500	-
6.2, Table 1(Average breaking strength - Lengthwise)	-	1600	Test charges+ specimen/conditioning ( 1100+500)
6.2, Table 1(Average breaking strength - Widthwise)	-	1600	Test charges+ specimen/conditioning ( 1100+500)
6.2, Table 1(Breaking strength of bottom seam)	-	1600	Test charges+ specimen/conditioning ( 1100+500)
6.2, Table 1(Breaking strength of centre seam)	-	1600	Test charges+ specimen/conditioning ( 1100+500)
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	0	-
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	0	-
6.3(Average breaking strength - Lengthwise after UV exposure)	-	1600	After UV Test charges+ specimen/conditioning ( 1100+500) (UV Resistance for 192 hrs. :10180 additional)
6.3(Average breaking strength - Widthwise after UV exposure)	-	1600	After UV Test charges+ specimen/conditioning ( 1100+500)
6.4(Drop Impact Testing of Filled Sacks)	-	1100	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 6.5 Table 1 viii(Ash content)	-	1200	-
4(Sack Type)	-	0	-
5.2.1(Fabric)	-	0	-
5.2.2(Linear density of tapes)	-	0	-
5.2.4(Unlaminated fabric mass)	-	0	-
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	0	-
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	0	-
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	0	-
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	0	-
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	0	-
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	0	-
5.4.1(Sack)	-	0	-
5.4.1.1(Centre seam)	-	0	-
5.4.1.2(Bottom seam)	-	0	-
5.4.2(Sack)	-	0	-
5.4.3(Sack)	-	0	-
5.4.5(Liner)	-	0	-
6.1.1, Table 1(Inside length)	-	0	-
6.1.1, Table 1(Inside width)	-	0	-
6.1.1, Table 1(Gusset width)	-	0	-
6.1.1, Table 1(Warp per dm)	-	0	-
6.1.1, Table 1(Weft per dm)	-	0	-
6.1.1, Table 1(Mass of laminated fabric)	-	0	-
6.2, Table 1(Average breaking strength - Lengthwise)	-	0	-
6.2, Table 1(Average breaking strength - Widthwise)	-	0	-
6.2, Table 1(Breaking strength of bottom seam)	-	0	-
6.2, Table 1(Breaking strength of centre seam)	-	0	-
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	0	-
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	0	-
6.3(Average breaking strength - Lengthwise after UV exposure)	-	0	-
6.3(Average breaking strength - Widthwise after UV exposure)	-	0	-
6.4(Drop Impact Testing of Filled Sacks)	-	0	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 6.5 Table 1 viii(Ash content)	-	0	-

21 Feb, 2029

-
-

IS 9755 (2021)

Textiles - High Density Polyethylene (HDPE) / Polypropylene (pp) Woven Sacks for Packing Fertilizers

All

35980 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.6(Drop Impact Test)	-	1000	-
4.1(Raw Meterial)	-	1050	-
4.2("Fabric a) Width of Tape")	-	250	-
4.2("Fabric b) Linear Density")	-	500	-
4.2("Fabric c) Mesh")	-	0	-
4.2("Fabric d) Unlaminated Fabric Mass")	-	0	-
4.3(Sacks)	-	300	-
4.4.1(Loose Liner)	-	300	-
4.4.1(Thickness of Linear)	-	0	-
4.4.2(Visual Observation)	-	250	-
4.4.3(Bottom Seam of Loose Liner)	-	0	-
4.5(Mass of The Lamination)	-	250	-
4.5(Laminated Fabric)	-	1050	-
4.5(Lamination Over Hang of the fabric after trimming)	-	0	-
4.6.1(Distance between the Two Row of Stitches)	-	0	-
4.6.1(Distance of outer stitch from the edge of the bag)	-	0	-
4.6.1(Depth of the Stitch( Double fold))	-	0	-
4.6.1(No.of Stitches/dm)	-	0	-
4.6.2(Breaking Load of the stitching material Non UV Stabilized sack)	-	0	-
4.6.2(Breaking Load for UV Stabilized sack)	-	0	-
4.7(Mouth of the Sack)	-	250	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension a) Inside Length Type 1 & Type 2 ")	-	250	-
"Table 1 of Cl. No.5.1 Sl. No. i"("Dimension b) Inside Width ")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. ii"(Ends/dm ( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.1 Sl. No. iii"(Picks /dm ( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric a) Unlaminated Sack( Type 1 & Type 2)")	-	500	-
"Table 1 of Cl. No.5.3 Sl. No. iv"("Mass of Fabric b) Laminated Sack( Type 1 & Type 2)")	-	500	-
"Table 1 of Cl. No.5.3 Sl. No. v"(Mass of Sack( Type 1 & Type 2))	-	250	-
"Table 1 of Cl. No.5.4 Sl. No. vi"(Avg. Breaking Strength Of fabric (Ravelled strip method)( 325mm X 25 mm))	-	2200	Lengthwise & Widthwise
"Table 1 of Cl. No.5.4 Sl. No. vii"(Breaking Strength of Bottom Seam (Ravelled strip method))	-	1100	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric a)Length(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.1 Sl. No. viii"("Elongation at Break of fabric b) Width(Type 1 & Type 2)")	-	0	-
"Table 1 of Cl. No.5.5 Sl. No. ix"("Ash Content a) For UV Stabilized Sack")	-	950	-
Cl. No.5.5("Ash Content b) For Non- UV Stabilized Sack")	-	950	-
Cl. No.5.6(Drop Impact testing of filled sack)	-	1000	-
Cl. No.5.2(Visual Observation)	-	0	-
Cl. No.5.3(Mass of Bale)	-	0	-
Cl. No.5.7(UV Resistance)	-	12380	UV Resistance (192 hrs.) + Breaking strength after UV 100 x 65 + 92x40+ 2200

21 Feb, 2029

-
-

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

All size

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	4100	Testing charges ( VCM Content + K- Value) ( 3000+1100)
4(Size of fitting)	-	0	-
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500	-
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0	-
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0	-
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	0	-
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	575	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	850	-
8(Marking)	-	0	-
3.2.3(socket, measurements)	-	0	-
6.3(Effect on water test)	-	3000	-

21 Feb, 2029

-
-

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

All size

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4100	VCM Content+ K- value ( 3000+1100)
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	500	-
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	0	-
3.2.3(Socket, measurements)	-	0	-

21 Feb, 2029

-
-

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

All

32280 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Mass of Bale)	-	0	-
5.2 Table 1(Dimensions)	-	250	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Ends per dm)	-	250	-
5.2 Table 1(Picks per dm)	-	250	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	250	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	1100	For UV Exposure for 192 hrs. (100x65 + 92x40): 10180
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	1100	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1100	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	1100	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	1100	-
5.2 Table 1(Drop impact strength)	-	1100	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	950	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	950	-
5.1(Mass of Bale)	-	0	-
5.2 Table 1(Dimensions)	-	250	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Ends per dm)	-	250	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Picks per dm)	-	250	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	250	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	1100	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1100	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	1100	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	1100	-
5.2 Table 1(Drop impact strength)	-	1100	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	950	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	0	-
4.6(Capacity)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3(Sacks)	-	0	-
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	0	-
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	0	-
4.2(Linear Density)	-	0	-
4.2(Width of tape)	-	0	-
Cl-4.4(Lamination Mass)	-	0	-
Cl-4.5(Liner- Thickness)	-	0	-
Cl-4.2 (Amendment No-2)(un-laminated fabric mass)	-	0	-
Cl-4.5(Liner- Width)	-	0	-
Cl-4.5(Liner- Visible defects)	-	0	-

21 Feb, 2029

-
-

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

All

50450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	500	--
7, see 8.3 and fig-1( GENERAL REQUIREMENTS OF PIPES/ visual appearance)	-	300	--
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	22850	Acceptance Test (10 hrs./27˚C):850, Type Test (1000 hrs./27˚C):11000 & Type Test (1000 hrs./60˚C):11000
7.3( Opacity)	-	575	--
9.2, table -11( Resistance to External Blows at 0 °C)	-	1000	--
8.2 table-9( Pipe Ends)	-	250	--
5 / 5.1(MATERIALS )	-	2000	--
5.3(VCM Content)	-	3000	--
5.4( K-Value)	-	1100	--
5.6 / 5.6.1( Material Classification, table -1)	-	250	--
6.0(CLASSIFICATION OF PIPES, table-2)	-	250	--
7.2( Colour)	-	250	--
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	500	--
8.1.2, table 4 to 7(Wall Thickness)	-	250	--
8.1.3 (Length, meter)	-	250	--
8.2 table-9(Dimensions of Integral Socket)	-	250	--
9.3 table-12( Ring Stiffness)	-	1400	For testing charges:1100+ For specimen:300
9.4, annexure-E( Orientation Factor)	-	900	For testing charges:700+ For specimen:200
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	6200	Vicat Softening temp. (VST):1100+ Effect on water:3000 + Resistance to dichloromethane at Specified temp.:1000+ Alternative test to resistance to Di- chloromethane test:1100
11,11.1( MECHANICAL CHARACTERISTICS OF ASSEMBLIES INCLUDING JOINTS/ 11.1 Assemblies with Non-End-Load-Bearing Joints)	-	1000	--
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	1000	--
11.3( Short-Term Negative Pressure Test for Leak Tightness of Assemblies)	-	1000	--
12(a)( ELASTOMERIC SEALS)	-	1050	--
12(b)( ELASTOMERIC SEALS)	-	375	--

21 Feb, 2029

-
-

IS 16205 : Part 24 (2017)

Conduit Systems for Cable Management part 24 Particular Requirements Conduit Systems Buried Under Ground

All

19950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Marking and Documentation)	-	300	-
6.1.1(Classification - Resistance to Compression)	-	1400	For testing + Specimen: 1100+300
6.1.2(Classification - Resistance to Impact)	-	1400	For testing:1100 + Specimen: 300
6.1.3(Classification - Resistance to Bending)	-	0	-
6.1.4 of IS 16205 (Part 1) : 2017(Classification - Tensile Strength)	-	0	-
6.1.5 of IS 16205 (Part 1) : 2017(Classification - Suspended Load Capacity)	-	0	-
6.3 of IS 16205 (Part 1) : 2017(Classification - According to Electrical Characteristics)	-	0	-
6.4 of IS 16205 (Part 1) : 2017(Classification - According to Resistance to External Influences)	-	0	-
6.5 of IS 16205 (Part 1) : 2017(Classification - According to Resistance to Flame Propogation)	-	0	-
7.1.2(Marking and Documentation)	-	300	-
7.1.3(Marking and Documentation)	-	0	-
7.1.101(Marking and Documentation)	-	0	-
7.2(Marking and Documentation)	-	0	-
7.5 of IS 16205 (Part 1) : 2017(Marking and Documentation)	-	0	-
7.6 of IS 16205 (Part 1) : 2017(Marking and Documentation)	-	0	-
7.101(Marking and Documentation)	-	0	-
7.102(Marking and Documentation)	-	0	-
8 Table 101(Dimensions)	-	250	-
8 Table 101(Dimensions)	-	0	-
9.1 of IS 16205 (Part 1) : 2017(Construction)	-	300	-
9.2 of IS 16205 (Part 1) : 2017(Construction)	-	0	-
9.4 of IS 16205 (Part 1) : 2017(Construction)	-	0	-
9.5 of IS 16205 (Part 1) : 2017(Construction)	-	0	-
9.6 of IS 16205 (Part 1) : 2017(Construction)	-	0	-
10.1(Mechanical Strength)	-	1600	Test charge + Specimen ( 1100+500)
10.3(Impact Test)	-	1600	Test charge + Specimen ( 1100+500)
10.4(Bending Test)	-	2000	Applicable on Pliable conduits
13.1.3(Spread of fire)	-	750	-
13.1.3.1(Spread of fire)	-	2900	-
13.1.3.2(Spread of fire)	-	0	-
14.0(External Influences)	-	10000	For IP 67 Test
15.0(Electromagnetic Compatibility)	-	300	-
10.2(Compression Test)	-	1600	Test charge + Specimen ( 1100+500)

21 Feb, 2029

-
-

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

All

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0 (chem)(MATERIAL)	-	1050	-
4.6.2(TRANSPARANCY)	-	700	-
4.6.3(LEAKAGE TEST)	-	1000	-
4.6.4(DROP TEST)	-	1100	-
4.6.5(MIGRATION TEST)	-	2000	Testing charges + specimen ( 1700+300)
4.6.6(PORTABILITY TEST)	-	900	-
4.6.5.1 (chem)(Colour migration (Caps))	-	300	-
4.6.5.1 (chem)(Colour migration (Container))	-	300	-
4.5, IS:2798:1998(Wall thickness- Bottom, in mm)	-	250	-
4.5, IS:2798:1998(Wall thickness- Middle , in mm)	-	0	-
4.5, IS:2798:1998(Wall thickness- Top , in mm )	-	0	-
4.4 , clause 5 of IS:2798:1998(Brimful capacity in ml)	-	0	-
4.3(Workmanship, Finish & Appearance)	-	0	-
4.2(Design, Shape & Dimension )	-	250	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (i)(Barium)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ii)(Cobalt)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iii)(Copper)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iv)(Iron)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (v)(Lithium)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vi)(Manganese)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vii)(Zinc)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (viii)(Antimony)	-	1000	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ix)(Phthalic acid, bis(2-ethylhexyl) ester (DEHP))	-	1000	-

21 Feb, 2029

-
-

IS 9271 (2004)

Unplasticized polyvinyl chloride (UPVC) single wall corrugated pipes for drainage - Specification (First Revision)

All

10400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2(Density-When tested in accordance with ]S 13360 (Part 3/Sec 1), the densi of the pipe shall be between 1.40 and 1.46 gm/cm3 .)	-	500	-
8.5(Elongation Test-(Annex C,)- pipes shall not elongate more than 7.5 percent)	-	1100	-
7.4.1(Perforation Requirement- There sh.all be maximum 8 rows of perforation)	-	500	-
5.1.1(MATERIAL-(Conform to IS 10151)-Up to 10 percent addition of the manufacturers own rework material produced during the manufacture and testing of pipes, complying With the standard IS pertmssible)	-	4100	VCM Content + K- Value ( 3000+1100)
7.4.2(Perforation Requirement-The maximum in flow area shall be 80 cm2/m length of pipe of all diameters)	-	0	-
7.4.3(Perforation Requirement-The heght of corrugation -The depth of corrugations shall be 3 percent, Min of nominal outside diameter (dn).)	-	0	-
5.1(MATERIAL-(Conform to IS 10151))	-	4100	VCM Content + K- Value ( 3000+1100)
5.1.2(MATERIAL)	-	0	declaration by manufacturer
5.1.3(MATERIAL- (Refer IS 4669))	-	1100	-
6(TYPES- perforated or non-perforated types.)	-	0	-
7, Table 1(DIMENSIONS AND TOLERANCE-The nominal outside diameter and tolerances of the corrugated pipes shall be as per Table 1)	-	500	-
7.2, 8(Wall Thickness)	-	0	-
7.3(Length)	-	0	-
7.4.1(Perforation Requirement-)	-	0	-
7.4.1,Table 2(Perforation Requirement-(Refer Table 2))	-	0	-
8.1.1(Visual Appearance, Workmanship and Finish)	-	300	-
8.1.2(Visual Appearance, Workmanship and Finish)	-	0	-
8.3,Table 3(Pipe stiffness-(Refer Annex A))	-	1100	-
8.4,Table 3(Impact Strength at 0 degree C- (refer Annex B))	-	1400	Testing charges + Specimen (1100+300)
8.6(BendIng Test-(Annex D,))	-	1000	-
8.7(Joints)	-	1000	-
7.2, 8(Wall Thickness)	-	0	-
8.2(Density-When tested in accordance with ]S 13360 (Part 3/Sec 1), the densi of the pipe shall be between 1.40 and 1.46 gm/cm3 .)	-	0	-
8.5(Elongation Test-(Annex C,)- pipes shall not elongate more than 7.5 percent)	-	1100	-

21 Feb, 2029

-
-

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

All Size

2700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	3000	-
3.2.1, Table-1, Fig-1(Nominal size)	-	0	-
3.2.1, Table-1, Fig-1(B)	-	0	-
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	0	-
3.2.1, Table-1, Fig-1(Plumbing)	-	0	-
Clause 3.2.2, and Fig. 2(Nominal size)	-	0	-
Clause 3.2.2, and Fig. 2.(B)	-	0	-
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	875	-
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	500	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	0	-
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	-
10.7 of IS 4985(Sulphated Ash content, Annex-B of IS 4985)	-	950	-
3.1(General)	-	4100	VCM Content + K- value ( 3000+1100)
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	0	-

21 Feb, 2029

-
-

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

All Size

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4100	VCM+ K-Value ( 3000+1100)
3.2, 3.2.1, Fig 1(Manufacture)	-	0	-
3.2.2, Fig 1(Dimensions)	-	0	-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	0	-

21 Feb, 2029

-
-

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

All Size

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4100	VCM Content+ K-value ( 3000+1100)
3.2, 3.2.1, Fig 1(Manufacture)	-	0	-
3.2.2, Fig 1(Dimensions)	-	500	-
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Equal Tees)	-	0	-

21 Feb, 2029

-
-

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

All size

5425 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4100	VCM + K- Value ( 3000+1100)
3.2, 3.2.1, Fig 1(Manufacture)	-	0	-
3.2.2, Fig 2, table 2(Dimensions)	-	500	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500	-
Table 2 (Cl.3.2.2, and Fig.1)(Dimensions of Flanged Tail Piece with Metallic Flange for Elastomeric Sealing Ring Joint)	-	0	-

21 Feb, 2029

-
-

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

All size

5225 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4100	VCM+ K- Value ( 3000+1100)
3.2(Materials)	-	2000	-
3.3, 3.3.1, Fig 1(Manufacture)	-	0	-
3.3.2, table 1, fig 1(Dimensions)	-	500	-
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	0	-
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	0	-

21 Feb, 2029

-
-

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

All Size

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4100	VCM Content+ K- value ( 3000+1100)
3.2, 3.2.1, Fig 2(Manufacture)	-	0	-
3.2.2, Fig 2, table 2(Dimensions)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	0	-
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	0	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	0	-

21 Feb, 2029

-
-

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

All size

4925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	4100	VCM content+ K- value ( 3000+1100)
3.2, 3.2.1, Fig 2(Manufacture)	-	0	-
3.2.2, Fig 1, table 1(Dimensions)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	0	-
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	0	-
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	0	-

21 Feb, 2029

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

CIPET, Jaipur

SP-1298, Sitapura Industrial Area, Phase III,Tonk Road, JAIPUR-302 022, Jaipur, Jaipur, Rajasthan, 302022

9090968451 cipetjprtesting@gmail.com

Scope List