BIS - LIMS (Laboratory Information Management System)

MSME TESTING CENTRE, CHENNAI

65/1, GST Road, Guindy, Chennai, Chennai, Tamil Nadu, 600032

9445662299 dctc-sr@dcmsme.gov.in

Scope List

Reset

42 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 5557 : Part 1 (2024)

All Rubber Gum Boots and Ankle Boots Part 1 Safety and Protective

10900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Design)	-	0	-
6(Sizes and Fittines)	-	0	-
7(Consturction)	-	0	-
8.1(Lining Material)	-	0	-
8.2, Table-1 (i)(Width, mm, Min)	-	100	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	400	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	300	-
8.4(Use of Rubber material)	-	0	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	300	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	400	-
8.5(Upper material)	-	0	-
8.5.1(Tensile Strength of upper)	-	400	-
8.5.2(Thickness)	-	100	-
8.5.3(Flexing Resistance)	-	400	-
8.5.4(Abrasion Resistance)	-	500	-
8.6.1(Thickness of Outsole)	-	100	-
8.6.2(Tear Strength)	-	400	-
8.6.3(Abrasion Resistance of Outsole)	-	400	-
8.6.4(Flexing Resistance)	-	400	-
8.6.5(Inter layer Bond Strength of outsole)	-	400	-
Cl-8.7(Insocks material)	-	0	-
8.7.1(Thickness of Insocks)	-	100	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	500	-
Cl-8.8.1(Outsole/Heel)	-	400	-
Cl-8.9(Leak Proof Test)	-	400	-
8.10(Height of Upper)	-	100	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	400	-
Cl-8.12(Upper Outsole Bond Strength)	-	400	-
Cl-8.13(Internal Length of Toe Cap)	-	100	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	300	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	300	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	300	-
8.17(Steel Floor with Glycerine)	-	300	-
8.18(Corrosion Resistant Test for Toe Caps)	-	300	-
9.1(Penetration Resistance)	-	300	-
9.2(Antistatic Footwear)	-	500	-
9.3(Flame Resistance Property)	-	200	-
9.4(Electrical Resistance)	-	500	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	300	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	300	-
9.6(Resistance to Fuel Oil)	-	300	-
11.2(Marking)	-	0	-
Cl-5(Design)	-	0	-
6(Sizes and Fittines)	-	0	-
7(Consturction)	-	0	-
8.1(Lining Material)	-	0	-
8.2, Table-1 (i)(Width, mm, Min)	-	0	-
8.2, Table-1 (ii)(Breaking load, N, Min (50 cm grip length test specimen))	-	0	-
8.3, Table-2 (i)(Sewing thread for piping/binding")	-	0	-
8.4(Use of Rubber material)	-	0	-
8.4.1, Table-3 (i)(Hardness, (IRHD))	-	0	-
8.4.1, Table-3 (ii)(Change in hardness after accelerated ageing at 100 ⁰C ± 2 ⁰C for 24 h)	-	0	-
8.5(Upper material)	-	0	-
8.5.1(Tensile Strength of upper)	-	0	-
8.5.2(Thickness)	-	0	-
8.5.3(Flexing Resistance)	-	0	-
8.5.4(Abrasion Resistance)	-	0	-
8.6.1(Thickness of Outsole)	-	0	-
8.6.2(Tear Strength)	-	0	-
8.6.3(Abrasion Resistance of Outsole)	-	0	-
8.6.4(Flexing Resistance)	-	0	-
8.6.5(Inter layer Bond Strength of outsole)	-	0	-
Cl-8.7(Insocks material)	-	0	-
8.7.1(Thickness of Insocks)	-	0	-
Cl-8.7.2(Abrasion Resistance of Insock)	-	0	-
Cl-8.8.1(Outsole/Heel)	-	0	-
Cl-8.9(Leak Proof Test)	-	0	-
8.10(Height of Upper)	-	0	-
8.11(Adhesion Test for Rubberized Textile Upper)	-	0	-
Cl-8.12(Upper Outsole Bond Strength)	-	0	-
Cl-8.13(Internal Length of Toe Cap)	-	0	-
Cl-8.14(Impact Resistance of Safety Footwear)	-	0	-
Cl-8.15(Compression Resistance of Safety Footwear)	-	0	-
8.17(Ceramic Tile Floor with sodium lauryl sulphate (NaLS))	-	0	-
8.17(Steel Floor with Glycerine)	-	0	-
8.18(Corrosion Resistant Test for Toe Caps)	-	0	-
9.1(Penetration Resistance)	-	0	-
9.2(Antistatic Footwear)	-	0	-
9.4(Electrical Resistance)	-	0	-
9.5(Resistance to Acid and Alkali- Limited contact with chemicals),)	-	0	-
9.5(Resistance to Acid and Alkali- Prolonged contact with chemicals)	-	0	-
9.6(Resistance to Fuel Oil)	-	0	-
11.2(Marking)	-	0	-

31 Dec, 2026

-
Included w.e.f.18.08.2025 Exclusion Cl 8.16 (Banned Chemicals) Cl 9.3 (Flame Resistance Property)

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

All type

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause - 4.2 & 4.2.1(Fe- 415, Fe- 415D, Fe-500, Fe-500D, Fe-550, Fe-550D, Fe-600 CARBON +EQUIVELENT )	-	0	-
4.1(Sulphur and phosphorous)	-	0	-
4.1(CE)	-	0	-
Cl 7.2(Weight)	-	600	-
Cl 6.1(Length, Width & Thickness)	-	0	-
Cl 5(Deformations and Surface Characteristics)	-	8400	-
4.1(Ni)	-	500	-
4.1(Mo)	-	500	-
4.1(Cr)	-	500	-
4.1( Ti)	-	500	-
4.1(V)	-	500	-
4.1( Nb)	-	500	-
4.1( Aluminium %)	-	500	-
4.1( Copper %)	-	500	-
4.1(Silicon %)	-	500	-
4.1(Sulphur %)	-	500	-
4.1(Phosphorus %)	-	500	-
4.1(Manganese %)	-	500	-
4.1(Carbon %)	-	500	-
Cl 9.4(Load In Other Direction From Bend)	-	500	-
Cl 9.3(Load In One Direction)	-	600	-
Cl 8.1(UTM)	-	1200	-
Cl.9.4 & Cl. 9.4.1(Rebend test)	-	1200	-
Cl. 9.3, Table 4(Bend Test )	-	1000	-
Cl. 8.1 Table 3(Elongation, percentage)	-	0	-
Cl. 8.1 Table 3(TS/YS ratio)	-	0	-
Cl. 8.1 Table 3(Tensile Strength (TS))	-	1200	-
Cl. 8.1 Table 3(Yield Stress (YS))	-	0	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-	600	-
4.1( Nitrogen%)	-	600	-

31 Dec, 2026

-
-

IS 5557 : Part 2 (2018)

All rubber gum boots and ankle boots: Part 2 occupational purposes

10700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(VISUAL)	-	0	-
3.2(specificgravity)	-	300	-
3.3(specificgravity)	-	300	-
3.4(specificgravity)	-	300	-
3.5(visual)	-	0	-
3.6(VISUAL)	-	0	-
3.7(VISUAL)	-	0	-
4(visual)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	0	-
7.1(visual)	-	0	-
7.1.1(Tear strength)	-	400	-
7.1.2(Abrasion resistance)	-	500	-
7.2(all test of table 1)	-	400	-
7.3(all test of table 2)	-	400	-
7.3(sulphur test)	-	400	-
7.4(Visual)	-	0	-
7.4.1(all test of table 3)	-	700	-
7.5(Visual)	-	0	-
7.5.1(Tensile)	-	400	-
7.5.2(Thickness)	-	100	-
7.5.3(Upper flexing)	-	500	-
7.6(VISUAL)	-	0	-
7.6.1(Out sole thickness)	-	200	-
7.6.2(out sole tear strength)	-	400	-
7.6.3(out sole abrasion)	-	400	-
7.6.4(out sole flexing)	-	400	-
7.6.5(Interlayer bond strength)	-	400	-
7.7(INSOCK Visual)	-	0	-
7.7.1(Insock thickness)	-	100	-
7.7.2(Insock abrasion)	-	500	-
8(CONSTRUCTION)	-	0	-
8.1(Hot contact)	-	400	-
8.2(Leak proofness)	-	400	-
8.3(Height of upper)	-	100	-
8.4(Adhesion test)	-	400	-
8.5(Resistance to acid & alkaline)	-	500	-
8.6(Resistance to fule oil)	-	400	-
8.7.1(Antistatic)	-	500	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	0	-
8.7.3(Elecrically nsulating footwear)	-	500	-
8.7.4(Resistance to cold)	-	400	-
10(Visual OBSERVATION)	-	0	-
11.1(Visual OBSERVATION)	-	0	-
11.2(Visual OBSERVATION)	-	0	-
11.3(Visual OBSERVATION)	-	0	-

31 Dec, 2026

-
Included w.e.f.10.12.2024 Exclusion CL 9.1 (ALLERIGIC DISPERSE DYES) CL 9.2 (Carcinogenic Disperse dyes) CL 9.3 (Phthalate)

IS 10702 (2023)

Hawai Chappal-Specification

4100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	0	OK
4.2(Length)	-	0	OK
4.4 , Table No. 1 , i)(Density)	-	300	OK
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	300	OK
4.4 , Table No. 1 , iii)(3Split tear strength)	-	300	OK
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	300	OK
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	300	OK
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	300	OK
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	300	OK
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	300	OK
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	300	OK
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	0	OK
4.4 , Table No . 2 , iv)(Stud bolt)	-	0	OK
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	300	OK
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	300	OK
5(CHEMICAL REQUIREMENT FOR HAWAI CHAPPAL)	-	0	OK
6(MARKING AND PACKING)	-	0	OK
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	0	OK
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	0	OK
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	0	OK
Cl.No. 5.2(lead content)	-	400	OK
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	300	OK
4.3(Thickness)	-	100	OK
Cl-4 ((Amendment No-1)(Category And Type)	-	0	OK
Cl-4.4, Table -1 S. No-1 (i) (Amendment No-1)(Compression set at constant stress)	-	0	OK
Cl-4.4, Table -1 S. No-1 (ii) (Amendment No-1)(Split tear strength)	-	0	OK
Cl-4.4, Table -1 S. No-1 (iii) (a)(Amendment No-1)("Shrinkage at Shrinkage at 50 °C ± 1 °C for 2 h for polymeric material, percent, Max ")	-	0	OK
Cl-4.4, Table -1 S. No-1 (iii)(b) (Amendment No-1)(Shrinkage at 100 °C ± 1 °C for 1 h for rubber, percent, Max)	-	0	OK
Cl-4.4, Table -1 S. No-1 (iv) (Amendment No-1)(Abrasion resistance at applied force)	-	0	OK
Cl-4.4, Table -1 S. No-1 (v) (Amendment No-1)(Flexing resistance: Maximum cut growth,)	-	0	OK
Cl-4.4, Table -1 S. No-1 (vi) (Amendment No-1)(Hydrolysis resistance:Maximum cut growth)	-	0	OK
Cl-4.4, Table -1 S. No-1 (viii) (Amendment No-1)("Lead content (as Pb), ppm, Max")	-	0	OK
Cl-4.4, Table -2 S. No-1 (i), a (Amendment No-1)("Breaking strength for Strap to strap 1-Solid strap 2-Cellular strap")	-	0	OK
Cl-4.4, Table -2 S. No-1 (i), b (Amendment No-1)("Breaking strength for Toe portion to strap 1-Solid strap 2-Cellular strap")	-	0	OK
Cl-4.4, Table -2 S. No-1 (i), c (Amendment No-1)("Elongation at break , percent, Min 1-Solid strap 2-Cellular strap")	-	0	OK
Cl-4.4, Table -2 S. No-1 (iii), (Amendment No-1)(Lead content (as Pb), in ppm, Max)	-	0	OK
Cl-4.4, Table -3 S. No-1 (i), (Amendment No-1)(Toe post attachment strength)	-	0	OK
Cl-4.4, Table -3 S. No-1 (ii), (Amendment No-1)(Attachment strength of rear strap)	-	0	OK
Cl-4.4, Table -3 S. No-1 (iii), (Amendment No-1)(Inter layer bond strength)	-	0	OK
Cl.4.4 - Table No 1 - Sl. No.-vii(pH- IS 1390:2022)	-	0	OK
Cl.4.4 - Table No 1 - Sl. No.-viii("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	0	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Exclusion:Cl. No.5.1,Table no.1 of IS 17011(i) (Allergenic and carcinogenic disperse dyes), Cl. No.5.1,Table no.1 of IS 17011(ii) (Aromatic amines released from Azo dyes (each individual amine)), Cl. No.5.1,Table no.1 of IS 17011(iii) (Aromatic amines released from Azo dyes (each individual amine)), Cl. No.5.1,Table no.1 of IS 17011(v) (Dimethyl fumarate (DMFU)), Cl. No.5.1,Table no.1 of IS 17011(vi) (Formaldehyde (free or released by partial hydrolysis)), Cl. No.5.1,Table no.1 of IS 17011(vii) (Formaldehyde), Cl. No.5.1,Table no.1 of IS 17011(viii) (Organotin compounds), Cl. No.5.1,Table no.1 of IS 17011(ix) (PCP-TeCP-TriCP polychlorophenols), Cl. No.5.1,Table no.1 of IS 17011(xi) (Phthalates (each individual phthalate)), Cl. No.5.1,Table no.1 of IS 17011(xii) (Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB)) Amendment No.1 Included w.e.f 03.05.2024

IS 9537 : Part 8 (2003)

Conduits for electrical installations - Specification: Part 8 rigid non - Threadable conduits of aluminium alloy

Aluminum Alloy Conduit

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(type test)	-	0	Testing charges applicable per sample per size.
4.2(ambient temperature)	-	0	Testing charges applicable per sample per size.
4.5(for rigid conduits, lengths)	-	0	Testing charges applicable per sample per size.
4.5(for pliable and flexible conduit coils)	-	0	Testing charges applicable per sample per size.
7(DIMENSIONS)	-	4000	Testing charges applicable per sample per size.
8(CONSTRUCTION)	-	1000	Testing charges applicable per sample per size.
9.2(Bending Test)	-	1000	Testing charges applicable per sample per size.
9.3(Compression Test)	-	1000	Testing charges applicable per sample per size.
clause No. 9.1(replacement)	-	1000	Testing charges applicable per sample per size.
clause No. 12(ELECTRICAL CHARACTERISTICS)	-	1000	Testing charges applicable per sample per size.

31 Dec, 2026

-
Included w.e.f. 02.04.2024

IS 2932 (2013)

Enamel, synthetic, exterior: (a) Undercoating (b) Finishing - Specification (Fourth Revision)

All Type

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3(Freedom from Coarse Particles)	-	200	-
6.4(Skin Formation)	-	0	-
6.5(Thinning Properties)	-	0	Sample along with suitable thinner 1 L can be submitted
6.6(Application Properties)	-	0	-
6.8(Lead Restriction)	-	800	-
6.9 Table 2 (1) a. Consistency ( Undercoating and Finishing ) )	-	200	-
6.9 Table 2 (1) b. Viscosity by ford 80-120 s )	-	500	-
6.9 Table 2 ( 2) Mass, ( Under coating ) )	-	500	-
6.9 Table 2 ( 2) Mass, (Finishing ) )	-	500	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Under coating ) )	-	1000	-
6.9 Table 2 (3) Drying time, a) Surface dry, ( Finishing ) )	-	200	-
6.9 Table 2 (b) Hard dry ( Under coating ) )	-	200	-
6.9 Table 2 (b) Hard dry, (Finishing ) )	-	200	-
6.9 Table 2 (c) Tack free ( Under coating (Finishing ) )	-	200	-
6.9 Table 2 (4) a) Finish (Under coating ) )	-	200	-
6.9 Table 2 (4) a) Finish (Finishing) )	-	200	-
6.9 Table 2 (b) ) Gloss 60º (Under coating ) )	-	500	-
6.9 Table 2 (b) ) Gloss 60º (Finishing) )	-	500	-
6.9 Table 2 (5) Fineness of grind,(Under coating ))	-	200	-
6.9 Table 2 (5) Fineness of grind,(Finishing))	-	200	-
6.9 Table 2 (6) Colour , (Finishing))	-	500	-
6.9 Table 2 (7) Flexibility and adhesion: a) Scratch hardness No such scratch as to show the bare metal after Clause 3 of — (Load 1 000 g) ( Under coating & Finishing ) )	-	500	-
6.9 Table 2 (b) Bend test (with 6.25 mm 48 h of air in type 1 apparatus) ( Under coating & Finishing ) )	-	500	-
6.9 Table 2 (8) Flash point ( Under coating & Finishing ) )	-	1000	-
6.9 Table 2 (9) Composition: a) Volume solids ( Under coating ))	-	1000	-
6.9 Table 2 (9) Composition: a) Volume solids ( Finishing))	-	1000	-
6.9 Table 2 (9) Composition:b) Phthalic anhydride content of non-volatile vehicle ( Under coating & Finishing ))	-	2000	-
6.9 Table 2 (10) Resistance to acid ( Under coating & Finishing ))	-	200	-
6.9 Table 2 (13) Keeping properties ( Under coating & Finishing ))	-	1000	-
6.9 Table 2 (12) Accelerated storage stability test ( Under coating & Finishing ))	-	1000	-
6.9 Table 2 (14) Wet opacity ( Under coating & Finishing ))	-	500	-

31 Dec, 2026

-
Included w.e.f. 02.04.2024 Exclusion: Cl.6.7.1.3 (QUV appratus)

IS 653 (1992)

Linoleum Sheets And Tiles

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.3-01-01(width of sheet)	-	200	-
5.3-01-02(Tolerance to tile size)	-	200	-
5.3-01-03(Thickness)	-	200	-
7("Squareness (for tiles only")	-	500	-
7(Seasoning (for plain linoleum only))	-	400	-
7(Residual Indentation)	-	1000	-
7(Flexibility)	-	500	-
7(Water absorption)	-	1000	-
7(Ageing)	-	1500	-
7("Colour fastness to day light")	-	1000	-

31 Dec, 2026

-
Included w.e.f. 28.03.2024

IS 15298 : part 4 (2017)

Personal protective equipment: Part 4 occupational footwear (Second Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1(CLASS I)	-	0	OK
Table 1(CLASS II)	-	0	OK
5.2.2.1(General)	-	0	OK
5.2.2.2(Height of upper)	-	100	OK
5.3.2.1(Construction)	-	0	OK
5.3.1.2(Upper/outsole bond strength)	-	400	OK
5.3.2.2(Leakproofness)	-	300	OK
5.3.2.3(Specific ergonomic features )	-	0	OK
5.3.4.1(Slip resistance)	-	500	OK
5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (SLS) solution)	-	0	OK
5.3.4.3(Slip resistance on steel floor with glycerine )	-	0	OK
5.3.4.4(Slip resistance on ceramic tile floor with SLS and on steel floor with glycerine )	-	0	OK
5.4.2.2(Thickness )	-	100	OK
5.4.2.3(Tear strenth)	-	400	OK
5.4.2.4(Tensile properties)	-	400	OK
5.4.2.5(Flexing resistance )	-	500	OK
5.4.2.6(Water vapour permeability and coefficient )	-	600	OK
5.5.2.4(pH value )	-	200	OK
5.5.2.5(Chromium VI content )	-	300	OK
5.4.2.8(Hydrolysis)	-	0	OK
5.5.2.1(Tear strength )	-	400	OK
5.5.2.2(Abrasion resistance )	-	500	OK
5.5.2.3(Water vapour permeability and coefficient )	-	0	OK
5.6.2.1(Tear strength )	-	0	OK
5.6.2.2(pH value )	-	0	OK
5.6.2.3(Chromium VI content )	-	0	OK
5.7.2.1(Insole and insock )	-	0	OK
5.7.2.2(Insole and insock )	-	0	OK
5.7.2.3(Water absorption and desorption )	-	500	OK
5.7.4.1(Abrasion resistance )	-	300	OK
5.7.4.2(Abrasion resistance )	-	300	OK
5.7.2.5(Chromium VI content )	-	0	OK
5.8.2.1(Outsole)	-	0	OK
5.8.1.1(Thickness )	-	100	OK
5.8.1.2(Cleated area )	-	0	OK
5.8.1.3(Cleat height)	-	0	OK
5.8.2.2(Tear strength )	-	400	OK
5.8.2.3(Abrasion resistance )	-	300	OK
5.8.2.4(Flexing resistance )	-	500	OK
5.8.2.5(Hydrolysis )	-	500	OK
5.8.2.6(Interlayer bond strength )	-	400	OK
6.2.1.1.2(Non-metallic anti-penetration insert used as an insole)	-	300	OK
6.2.1.2(Construction)	-	0	OK
6.2.1.3(Dimensions )	-	0	OK
6.2.1.5.1(Corrosion resistance of penetration-resistant metallic inserts)	-	300	OK
6.2.1.5.2(Penetration-resistant non-metallic inserts)	-	0	OK
6.2.2.1(Conductive footwear)	-	0	OK
6.2.2.2(Antistatic footwear)	-	500	OK
6.2.3.1(Heat insulation of sole complex )	-	500	OK
6.2.3.2(Cold insulation of sole complex)	-	500	OK
6.2.2.4(Energy absorption of seat region )	-	400	OK
6.2.2.5(Water resistance )	-	0	OK
6.2.2.6(Ankle protection)	-	0	OK
6.2.7.1(Cut resistance foot wear)	-	500	OK
6.2.7.2(Cut resistance foot wear)	-	0	OK
6.3.2.2(Upper- water penetration)	-	300	OK
6.4.2.1(Resistance to hot contact)	-	300	OK
6.4.2.2(Resistance to fuel oil)	-	400	OK
5.2.2.3(Seat region)	-	0	OK
5.4.2.1(Upper)	-	0	OK
5.4.2.7(pH value )	-	0	OK
5.4.2.9(Chromium VI content )	-	0	OK
6.2.2.3(Electrically insulating footwear )	-	500	OK
6.2.7.3(Resistance to cutting)	-	0	OK
6.2.7.4(Pentration resistance)	-	0	OK
6.2.1.1(Metallic anti-penetration insert )	-	0	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Exclusion: Cl.6.2.1.4 (Flex resistance of penetration-resistant inserts ), Cl.5.3.2.5 (Innocuousness )

IS 15298 : Part 3 (2019)

Personal protective equipment: Part 3 protective footwear (Second Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.2 Table-2(Height of upper)	-	0	-
5.3.1.1 Table-2(Construction)	-	0	-
5.3.1.2 Table-2(Upper/Outsole Bond)	-	400	-
Table-2(Strength)	-	0	-
5.3.2.1 Table-2(General)	-	0	-
5.3.2.2 Table-2(Internal Length of toe cap)	-	0	-
5.3.2.3 Table-2(Impact Resistance -T- )	-	400	-
5.3.2.4 Table-2(Compression)	-	400	-
5.3.3 Table-2(Leak Proofness)	-	300	-
5.3.5.2 Table-2(Slip Resistance SRA)	-	500	-
5.3.5.3 Table-2(Slip Resistance SRB)	-	500	-
5.3.5.4 Table-2(Slip Resistance SRC)	-	500	-
5.4.1 Table-2(General)	-	0	-
5.4.2 Table-2(Thickness)	-	100	-
5 4 3 Table-2(Tear Strength)	-	400	-
5.4.4 Table-2(Tensile Properties)	-	400	-
5.4.5 Table-2(Flexing Resistance)	-	500	-
5.4.6 Table-2(Water Vapour Permeability & Coefficient)	-	700	-
5 4.7 Table-2( )	-	200	-
5 4.8 Table-2(Hydrolysis)	-	500	-
5.4 9 Table-2(Chrome VI)	-	300	-
5.5.1 Table-2(Tear Strength)	-	400	-
5.5.2 Table-2(Abrasion Resistance)	-	500	-
5.5.3 Table-2(Water Vapour Permeability & Coefficient)	-	0	-
5.5.4 Table-2(pH Value)	-	200	-
5.5.5 Table-2(Chrome VI)	-	300	-
5.6.1 Table-2(Tear Strength)	-	0	-
5.6.2 Table-2(pH Value)	-	200	-
5.6.3 Table-2(Chromium VI)	-	300	-
5.7.3 Table-3(Water Absorption &)	-	500	-
Table-3(Desorption)	-	0	-
5.8.6 Table-2(Interlayer BondStrength)	-	400	-
6.2.1 Table-I8(Penetration Resistance)	-	300	-
6.2.2.1 Table-18(Electrical Properties)	-	500	-
6.2.2.2 Table-18(Antistatic Footwear)	-	500	-
6.2.3.1 Table-18(Heat Insulated Comp)	-	500	-
6.2.3.2 Table-18(Cold Insulated)	-	500	-
6.2.4 Table-18(Energy Absorption of seat region)	-	400	-
6.2.5 Table-18(Water Resistance)	-	200	-
6.2.7 Table-18(Ankle Protection)	-	500	-
6.2.8 Table-18(Cut Resistance)	-	500	-
6.3 Table-18(Water Penetration & Absorption)	-	300	-
6.4.1 Table-18(Resistance to Hot Contact)	-	300	-
6.4.2 Table-18(Resistance to Fuel oil)	-	400	-
8.2.1(Conductive footwear)	-	500	-
8.2.2(Antistatic footwear)	-	500	-

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Excluding Footwear with electrical insulating

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

Insulation A,C,D/Sheath ST1,ST2,ST3/Cat 01,02,FR/AYY

20000 View breakup
Type Test: Rs.10000/- (1 core), Rs.11000/- (2 core), Rs.13000/- (3 core), Rs.15000/- (3 1/2, 4 core) Optional Tests Cold Bend test – Rs 1500 /- Cold Impact – Rs 1500 /-Additional Ageing Test – Rs 1500/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	3000	-
10.4(Flammability test- Unaffected portion)	-	500	-
10.4(Flammability test-Burning after flame removal)	-	500	-
table 1 e) 3) (IR constant- max. Temp)	-	250	-
table 1 e) 3) (IR constant- Room temp )	-	250	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	250	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	250	-
10.2(HV (room temperature))	-	1000	-
10.1(HV (water immersion))	-	750	-
10.1(HV (water immersion))	-	750	-
10.6(Halogen evolution)	-	5000	-
10.7(Temperature index)	-	5000	-
10.5(Oxygen index)	-	5000	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	500	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	500	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	500	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	500	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	500	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	500	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	500	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	500	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	500	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	500	-
Table 1 iii) d) 4)(Cracks Observed)	-	500	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	500	-
Table 1 iii) c) 4)(Cracks Observed)	-	500	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	500	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	500	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	500	-
Table 1 iii) d) 3)(Sheath- Elongation variation)	-	625	-
Table 1 iii) d) 3)(Sheath- TS variation)	-	625	-
Table 1 iii) d) 3)(Sheath- Elongation (After ageing))	-	625	-
Table 1 iii) d) 3)(Sheath- Tensile strength (After ageing))	-	625	-
Table 1 iii) d) 1)(Sheath- Elongation (Without ageing))	-	625	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	625	-
Table 1 iii) c) 3)(Elongation variation)	-	625	-
Table 1 iii) c) 3)(TS variation)	-	625	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	625	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	625	-
8.3(Thickness of Sheath)	-	500	-
5.3(Thickness of Insulation)	-	500	-
9.1(Ovality)	-	500	-
9(Overall dimensions)	-	500	-
4.2(Conductor resistance test)	-	500	-
4.1(Wrapping test (for Al))	-	400	-
4.1(Tensile test (for Al)- After Stranding)	-	1000	-
4.1(Tensile test (for Al)-Before Stranding)	-	1000	-
4.1(Annealing test (for copper))	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor- Diameter )	-	500	-
8.3(Minimum thickness of Sheath)	-	250	-
8.3(Avarage thickness of Sheath)	-	250	-
5.3(Minimum thickness of insulation)	-	250	-
5.3(Avarage thickness of insulation)	-	250	-
11.1(Durability)	-	500	-
13(Cable code)	-	500	-
11.2(Legibility)	-	500	-
11(Identification)	-	500	-
Table 1(Category Code)	-	500	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4)(Colour of Sheath)	-	500	-
5.2(Application )	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)( Flexible Conductors (Classes 5))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors(Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded compacted circular conductors and shaped conductors (Class 2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Stranded circular non compacted conductors (Class-2))	-	500	-
(Cl.6.1.3 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.6.1 of IS 8130:2013)(Solid Conductor (Class 1))	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl.16.1) (Cl.19.1)(Conductor)	-	500	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3)(Assembly of cores )	-	500	-
12(CONSTRUCTION Core Identification)	-	500	-
8.1(Sheath Material )	-	500	-
7(Binder Tape)	-	500	-
6.2(Filler)	-	500	-
6.1(Filler)	-	500	-
5.1(Insulation)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.4(Joints in Conductor)	-	500	-
4.1(Conductor - Material)	-	500	-
4.1(Conductor - Material)	-	500	-
12.0(Core identification)	-	500	-
4, IS 8130(Construction of conductor)	-	500	-
Table 2, IS 8130(No fo wire in a conductor)	-	500	-
10.11(Per sulphate test (for tinned Cu cable only))	-	500	-
Table 4(Copper purity test)	-	660	-
5.4(Mechanical properties before and after ageing)	-	2500	-

31 Dec, 2026

-
Exclusion: Cl.10.8 (smoke density rating), Cl.10.3 (spark test)

IS 7098 : Part 1 (1988)

Specification for crosslinked polyethylene insulated pvc sheathed cables: Part 1 for working voltages up to and including 1100 volts (First Revision)

XLPE Insulated/ST2 PVC Sheathed/A2XFY/A2XWY/FR

22000 View breakup
Type test: Rs.11000/- or Rs.6000/- for two core, Rs.13000/- or Rs.7000/- for three core, Rs.15000/- or Rs.8500/- for 3.5 & 4 core, Optional Test Cold bend test – Rs 1500 /- Cold impact test – Rs 1500 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15.1 a) i)(Annealing Test ( For copper wire ) )	-	500	-
15.1 a) ii)(Tensile test (for aluminium) - Before stranding )	-	400	-
15.1 a) ii)(Tensile test (for aluminium) - After stranding )	-	400	-
15.1 a) iii)(Wrapping test (for aluminium))	-	400	-
15.1 a) iv)(Resistance test - Main conductor)	-	250	-
15.1 a) iv)(Resistance test - Neutral conductor)	-	250	-
15.1 d) i) (Phyaical tests for insulation : Tensile Test)	-	500	-
15.1 d) i) (Phyaical tests for insulation : Elongation)	-	500	-
15.1 d) ii) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	500	-
15.1 d) iii) (Phyaical tests for insulation : Hot set )	-	1000	-
15.1 d) iii) (Phyaical tests for insulation : Permanent set )	-	2500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d) iv) (Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	-
15.1 d) v) (Insulation: Waterabsorption(gravimetric))	-	500	-
15.1 e) i) (Physical tests for outer sheath : Tensile stregth)	-	250	-
15.1 e) i) (Physical tests for outer sheath : Elongation)	-	250	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	625	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-	625	-
15.1 e) ii) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	625	-
15.1 e) ii) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	625	-
15.1 e) iii) (Sheath: Loss of mass in air oven)	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 e) iv) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	-
15.1 e) v) (Sheath : Hot deformation)	-	500	-
15.1 e) vi) (Sheath : Heat shock test)	-	500	-
15.1 e) vii) (Sheath : Thermalstability)	-	500	-
15.1 f)(INSULATION RESISTANCE TEST : Volume resistivity )	-	1000	-
16.2(HIGH VOLTAGE TEST )	-	500	-
16.3(FLAMMABILITY TEST : Period of Burning )	-	500	-
16.3(FLAMMABILITY TEST : Unaffected length )	-	500	-
16.9(Oxygen Index Test)	-	5000	-
16.14(Temperature Index)	-	5000	-
17.1(Manufacturer'. identification)	-	500	-
17.2(cable Indentification )	-	500	-
17.3(cable Code )	-	500	-
15.4 (a)(Cold bend)	-	500	-
15.4 (b)(Cold impact)	-	500	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	625	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	625	-
Table 1(Ageing in air oven - Elongation on Insulation)	-	625	-
Table 1(Ageing in air oven - Tensile strength on Insulation)	-	625	-
Table 4(Copper purity test)	-	660	-
Table 2(Cold Impact test for Outer sheath)	-	500	-
Table 2(Cold bend test for Outer sheath)	-	500	-
3(CONDUCTOR: MATERIALS)	-	500	-
4(INSULATION : MATERIALS)	-	500	-
5.1(FILLER AND INNER SHEATH)	-	500	-
5.2(FILLER AND INNER SHEATH)	-	500	-
6(ARMOURING)	-	500	-
7(OUTER SHEATH)	-	500	-
8.1(CONDUCTOR: CONSTRUCTION)	-	500	-
8.2(PROTECTIVE BARRIER)	-	500	-
8.3(SIZE OF NEUTRAL CONDUCTOR)	-	500	-
9.1(Insulation Applied by extrusicn)	-	500	-
9.2(Thickness of Insulation - Average)	-	500	-
9.3(Thickness of Insulation - Minimum)	-	500	-
9.4(Application of Insulation)	-	500	-
10.1(Core Identification)	-	500	-
10.2(Core Identification- Neutral)	-	500	-
10.3(Core Identification by number )	-	500	-
10.4(Core Identification by number - Neutral )	-	500	-
11(LAVING UP OF CORES)	-	500	-
12.1 & 12.2(Inner sheath : Application)	-	500	-
12.3(Thickness of Inner Sheath)	-	500	-
13.1(Armouring: Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(Armouring: Direction of Lay )	-	500	-
13.2(Type of armour )	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(Armour: Joint)	-	500	-
13.5(Armouring : Resistance Test)	-	500	-
13.6 a)(ARMOURING: Tensile Strength)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	500	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	1000	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(Outer Sheath : Application)	-	500	-
14.2(Colour of outer sheath)	-	500	-
14.3(Thickness of outer sheath - AVERAGE)	-	500	-
14.3(Thickness of outer sheath - minimum)	-	500	-
16.13(Test for Halogen Acid Gas Evolution)	-	5000	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-

31 Dec, 2026

-
-

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

1100V/Type A/C/ST1/ST2/AYFY/AYWY/CAT01

15000 View breakup
Type test: Rs.14000/- (2 core), Rs.17000/- (3 core), Rs.19000/- (3 1/2, 4 core) Optional Tests Cold Bend test – Rs 1500 /- Cold Impact – Rs 1500 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(MATERIALS : CONDUCTOR)	-	500	-
4.1.1(INSULATION : General Purjose Insulaiion)	-	500	-
4.1.2(INSULATION : Heat Resisting Insulation)	-	500	-
5.1(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
5.2(MATERIALS : FILLER AND INNER SHEATH)	-	500	-
6.1(MATERIALS : ARMGURING)	-	500	-
6.2(MATERIALS : ARMGURING)	-	500	-
7.1.1(OUTER SHEATH : For Cables with General Purpose InsuIafion)	-	500	-
7.1.2(OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-	500	-
8.1(CONSTRUCTION : CONDUCTOR)	-	500	-
8.2(CONSTRUCTION : CONDUCTOR)	-	500	-
9.1(INSULATION )	-	500	-
9.2(INSULATION : Thickness of Insulation)	-	250	-
9.3(INSULATION :Tolerance on Thickness of Insulation)	-	250	-
9.4(INSULATION : Application of Insulation)	-	500	-
10.1(CORE IDENTIFICATION)	-	500	-
10.2(CORE IDENTIFICATION)	-	500	-
10.3(CORE IDENTIFICATION)	-	500	-
10.3.1(Arrangement of Marking)	-	500	-
11.1(LAYING UP OF CORES)	-	500	-
11.2(LAYING UP OF CORES)	-	500	-
12.1(INNER SHEATH)	-	500	-
12.2(INNER SHEATH)	-	500	-
12.3(INNER SHEATH :Thickness of Inner Sheath)	-	250	-
12.3.1(INNER SHEATH :Thickness of Inner Sheath)	-	250	-
13.1.1(ARMOURING : Application)	-	500	-
13.1.2(Armouring: Coverage )	-	500	-
13.1.3(ARMOURING : Direction of lay )	-	500	-
13.1.4(ARMOURING : Application)	-	500	-
13.2(ARMOURING : Type of Armour)	-	500	-
13.2.1(ARMOURING : Type of Armour)	-	500	-
13.3(Armouring : Dimensions -Wire Diameter)	-	500	-
13.3(Armouring : Dimensions -Formed wire )	-	500	-
13.4(ARMOURING : Joints)	-	500	-
13.5.1(ARMOURING : Resistance)	-	250	-
13.5.2(ARMOURING : Resistance)	-	250	-
13.6 a)(ARMOURING: Tensile Strength)	-	500	-
13.6 b)(ARMOURING: Elongation )	-	500	-
13.6 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	-
13.6 d)(ARMOURING: Winding Test(For formed wire))	-	500	-
13.6 e)(ARMOURING: Uniformity of zinc coating)	-	1000	-
13.6 f)(ARMOURING: Mass of zinc coating )	-	1000	-
13.6 g)(ARMOURING: Resistivity)	-	1000	-
14.1(OUTER SHEATH)	-	500	-
14.2(OUTER SHEATH)	-	500	-
14.3(OUTER SHEATH : Colour )	-	500	-
14.4.1(Thickness of Outer Sheath : Unarmowed Cables)	-	500	-
14.4.2(Thickness of Outer Sheath : Armoured Cables)	-	500	-
15.1 a) 1)(Tests on conductor : Annealing test ( for copper ))	-	500	-
15.1 a) 2)(Tensile test (for aluminium) - Before stranding )	-	400	-
15.1 a) 2)(Tensile test (for aluminium) - After stranding )	-	400	-
15.1 a) 3)(Tests on conductor : Wrapping test ( for aluminium ))	-	400	-
15.1 a) 4)(Tests on conductor : Conductor resistance test)	-	250	-
15.1 a) 4)(Resistance test - Neutral conductor )	-	250	-
15.1 d)1)(Phyaical tests for insulation : Tensile Test)	-	250	-
15.1 d)1)(Phyaical tests for insulation : Elongation )	-	250	-
15.1 d)1)(Physical tests for sheath : Tensile stregth )	-	250	-
15.1 d)1)(Physical tests for sheath : Elongation )	-	250	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-	625	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air oven : Elongation )	-	625	-
15.1 d)2)(Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-	625	-
15.1 d)2)(Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-	625	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-	625	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation )	-	625	-
15.1 d)2)(Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-	625	-
15.1 d)2)(Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-	625	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for insulation : Shrinkage - Crack observed )	-	500	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage )	-	500	-
15.1 d)3)(Phyaical tests for Sheath : Shrinkage - Crack observed )	-	500	-
15.1 d)4)(Hot deformation : Insulation )	-	500	-
15.1 d)4)(Hot deformation : Sheath )	-	500	-
15.1 d)5)( Loss of mass in air oven- Insulation )	-	500	-
15.1 d)5)( Loss of mass in air oven- sheath )	-	500	-
15.1 d)6)(Heat shock test- Insulation )	-	500	-
15.1 d)6)(Heat shock test- sheath )	-	500	-
15.1 d)7)(Thermal stability- insulation )	-	500	-
15.1 d)7)(Thermal stability- Sheath )	-	500	-
15.1 e)(Insulation resistance test : Volume Resistivity )	-	500	-
15.1 e)(Insulation resistance test : IR Constant )	-	500	-
15.1 f)(High voltage test ( water immersion test ))	-	1500	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.1 g)(High voltage test at room temperature)	-	1000	-
15.4 a)(Cold bend test- Insulation ( Optional test))	-	500	-
15.4 a)(Cold bend test- Sheath ( Optional test))	-	500	-
15.4 c)(Armour resistance test ( for other than mining cables ).- Optional test )	-	500	-
16.1(DETAILS OF TESTS : General)	-	500	-
16.2(DETAILS OF TESTS : High Voltage Test at Room Temperature)	-	500	-
16.3.1(High Voltage Test ( Water Immersion Test ) : a.c. Test)	-	1500	-
16.3.2(High Voltage Test ( Water Immersion Test ) : d.c. Test)	-	1500	-
16.4(Flammability Test)	-	1000	-
16.5(Oxygen Index Test)	-	5000	-
16.9(Test for Halogen Acid Gas Evolution)	-	5000	-
16.1(Temperature Index)	-	5000	-
17.1(IDENTIFICATION : Manufacturer’s Identification)	-	500	-
17.2(IDENTIFICATION : Cable Identification)	-	500	-
17.2.1(IDENTIFICATION : Cable Identification)	-	500	-
17.3(IDENTIFICATION : Cable Code)	-	500	-
15.1.e(Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Insulation resistance constant At Room temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Maximum rated temperature temperature)	-	1000	-
15.1.e(Insulation resistance Test- Volume Resistivity At Room temperature)	-	1000	-
16.4(Flammability Test- Un affected portion)	-	500	-
16.4(Flammability Test- Period of Burning)	-	500	-
9.3(Minimum Thickness of Reduce core insulation)	-	500	-
9.2(Thickness of Reduce core insulation)	-	500	-
3.1 Table 2 IS 8130(Number of wires in the conductor)	-	500	-
Table 4(Copper purity test)	-	660	-

31 Dec, 2026

-
Exclusion: Cl.16.10 smoke density test, Cl.16.8 (Test for specific optical density & smoke)

IS 15298 : Part 2 (2016)

Personal protective equipment: Part 2 safety footwear (Second Revision)

13500 View breakup
-

Clause No.	Exclusion	Remark
4,Table 1(Class I, IS 15298)	-	NIL
4,Table 1(Class II, IS 15298)	-	NIL
5.2,5.2.1, Fig 3(Design,General, IS 15298)	-	NIL
5.2.2, Fig 4(Height of Upper, ISO 20344 , 6.2)	-	NIL
5.2.3, Table 10 ,Design A(Seat Region)	-	NIL
5.3.1.1(Construction)	-	NIL
5.3.1.2(Upper/outer sole bond strength , ISO 20344 , 5.2)	-	NIL
5.3.2.1(General, EN 12568 OF 4.2.2.2)	-	NIL
5.3.2.2,Table 5(Internal length of toecaps , ISO 20344 , 5.3)	-	NIL
5.3.2.3,Table 6(Impact resistance of safety footwear,ISO 20344 , 5.4)	-	NIL
5.3.2.4 ,Table 6(Compression Resistance of safety footwear ,ISO20344 , 5.5)	-	NIL
5.3.2.5.1(Corrosion resistance of metallic toecaps ,ISO20344 , 5.6.2)	-	NIL
5.3.2.5.2(Non metallic toe caps ,EN 12568)	-	NIL
5.3.3(Leak proofness ,ISO 20344 , 5.7)	-	NIL
5.3.4(Specific ergonomic feature ,ISO 20344 , 5.1)	-	NIL
5.3.5.2,Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	NIL
5.3.5.3,Table 8(Slip resistance on steel floor with glycerin)	-	NIL
5.3.5.4(Slip resistance on ceramic tile floor with NaLS and on steel floor with glycerin)	-	NIL
5.4.1,Table 10(General)	-	NIL
5.4.2, Table 11(Thickness , ISO 20344 , 6.1 )	-	NIL
5.4.3, Table 12(Tear Strength, ISO 20344 , 6.3 )	-	NIL
5.4.4, Table 13(Tensile properties ,ISO 20344 , 6.4.1 )	-	NIL
5.4.5, Table 14(Flexing resistance ,ISO 20344,6.5)	-	NIL
5.4.6(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	NIL
5.4.8(Hydrolysis ; ISO 20344,6.10)	-	NIL
5.5.1,Table 15(Tear Strength, ISO 20344 , 6.3)	-	NIL
5.5.2(Abrasion Resistance ;ISO 20344 , 6.12)	-	NIL
5.5.3(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	NIL
5.6(Tongue - IS 15298 Part 2 )	-	NIL
5.6.1,Table 16(Tear Strength, ISO 20344 , 6.3)	-	NIL
5.6.2(Ph Value ; ISO 20344,6.9)	-	NIL
5.6.3(Chromium VI content; ISO 17075)	-	NIL
5.7.1;Table 3(Thickness ; ISO 20344,7.1)	-	NIL
5.7.2(Ph Value ; ISO 20344,6.9)	-	NIL
5.7.3(Water Absorption and desorption ISO 20344,7.2 )	-	NIL
5.7.4.1(Insole ; ISO 20344,7.3 )	-	NIL
5.7.4.2(Insocks ; ISO 20344, 6.12)	-	NIL
5.8.1.2(Cleated area)	-	NIL
5.8.1.3, Table 17(Cleat height; ISO 20344, 8.1)	-	NIL
5.8.2(Tear Strength, ISO 20344 , 8.2)	-	NIL
5.8.3(Abrasion Resistance ;ISO 20344 , 8.3)	-	NIL
5.8.4(Flexing resistance ,ISO 20344,8.4)	-	NIL
5.8.5(Hydrolysis ; ISO 20344,8.5)	-	NIL
5.8.6(Interlayer bond strength; ISO 20344, 5.2)	-	NIL
6.2.1.1.1(Metallic anti-penetration insert; ISO 20344, 5.8.2)	-	NIL
6.2.1.1.2(Non-metallic anti-penetration insert; ISO 20344, 5.8.3)	-	NIL
6.2.1.2(Consruction)	-	NIL
6.2.1.3(Dimension ; ISO 20344, 5.8.1)	-	NIL
6.2.1.5.1(Corrosion resistance of penetration -resistant metallic insert - ISO 20344, 5.6.3 &5.6.1)	-	NIL
6.2.2.1 (Conductive footwear ; ISO 20344,5.10 & 5.10.3.3)	-	NIL
6.2.2.2(Antistatic footwear ; ISO 20344,5.10)	-	NIL
6.2.3.1(Hear insulation of sole complex; ISO 20344,5.12 ;Annex B)	-	NIL
6.2.3.2(Cold insulation of sole complex; ISO 20344,5.13)	-	NIL
6.2.4(Energy absorption of seat region; ISO 20344,5.14)	-	NIL
6.2.5(Water resistance ; 5.15.1 & 5.15.2)	-	NIL
6.2.6.1(Construction)	-	NIL
6.2.6.2 , Table 19(Impact resistance of metatarsal protective device,ISO 20344 , 5.16)	-	NIL
6.2.7 (Ankle protection ; ISO 20344 , 5.17)	-	NIL
6.2.8.1(Design)	-	NIL
6.2.8.2(Construction)	-	NIL
6.2.8.3,EN 388(Resistance to cutting ,EN 388)	-	NIL
6.2.8.4(Penetration Resistance)	-	NIL
6.3(Upper--Water penetration and absorption ; ISO 20344 , 5.13)	-	NIL
6.4.1(Resistance to hot contact ; ISO 20344 , 8.7)	-	NIL
6.4.2(Resistance to fuel oil ; ISO 20344 , 8.6.1& 8.6.2 ; )	-	NIL
Cl.5.3.5.1, Cl.5.3.5.2,Cl.5.3.5.3 or 5.3.5.4 IS 15298 (Part1):2015,ISO 20344:2011,5.11(General)	-	NIL

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Exclusion: Cl.6.2.1.4 (Flex resistance of penetration -resistant insert ; ISO 20344,5.9), Cl.5.3.6 (Innocuousness)

IS 13995 (1995)

Unlined moulded rubber boots - Specification

Unlined moulded rubber boots

2700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.7(Size)	-	100	OK
5.1.6(Design)	-	0	OK
5.1.5(Flexing resistance of upper)	-	600	OK
5.1.4(Resistance to dry heat ageing )	-	500	OK
5.1.3(Tear Strength)	-	300	OK
5.1.2(Tensile Strength (after ageing))	-	800	OK
5.1.1(Tensile Strength (before ageing))	-	300	OK
4.1(Thickness )	-	100	OK
6, 6.1(Marking)	-	0	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024

IS 11544 (1986)

Specification for slipper, rubber

3800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.6(Thickness of components)	-	100	OK
3.2.5(Type of Thread)	-	400	OK
3.2.4(Picks per cm)	-	100	OK
3.2.4(End per cm)	-	100	OK
3.2.4(Mass per unit area)	-	300	OK
3.2(Flexural endurance)	-	1500	OK
3.2(Hardness after ageing)	-	500	OK
3.2(Hardness (IRHD))	-	300	OK
3.2(Relative density )	-	300	OK
3.1(Shape & Design)	-	100	OK
3.2.2(Bottom Filling Material)	-	0	OK
3.2.4.1(Weave of fabrics)	-	0	OK
3.2.7(vulcanized process)	-	0	OK
3.2.8(Workmanship and Finish -)	-	0	OK
3.2.9(Preservation -)	-	100	OK
Cl. 4, Cl. 4.1, Cl 4.2, Cl. 4.3(Marking and packing)	-	0	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Exclusion: 3.2.4 (Colour fasntess to washing)

IS 6719 (1972)

Solid Pvc Soles And Heels

2100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6.1(Hardness )	-	300	OK
3.6 (vi)(Lead (as Pb) ppm)	-	300	OK
3.6 (v)(Volatility, percent by means )	-	200	OK
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	500	OK
3.6 (iii)(Elongation at break, percent )	-	0	OK
3.6 (ii)(Tensile Strength )	-	500	OK
3.6 (i)(Relative density )	-	300	OK
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	0	OK
6 ,6.1,6.2,6.3(Test Method)	-	0	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	0	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	300	OK
Cl.4.1.3 And 8.3,Table1, iii)(Hardness, Shore A durometer min)	-	300	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	500	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	500	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	400	OK
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	200	OK
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi)(Heat shrinkage test at 100±1°C for 1 hour max)	-	300	OK
Cl.4.1.3 And 8.3,Table1(viii)Water absorption , percent by mass, Max)	-	200	OK
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii)(Flexing resistance: Maximum cut growth at 50 000 cycles)	-	700	OK
5, 5.1(Marking)	-	0	OK
6, 6.1(Packing)	-	0	OK
4.2(Size & Thickness )	-	100	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024 Amendment No.1 Included w.e.f 03.05.2024

IS 5557 (2004)

Industrial and protective rubber knee and ankle boots - Specification (Fourth Revision)

7300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	500	OK
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	0	OK
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	100	OK
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	100	OK
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	2300	OK
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	900	OK
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	600	OK
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	100	OK
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	0	OK
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	300	OK
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	300	OK
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	600	OK
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	300	OK
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	500	OK
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	600	OK
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	100	OK
6.1(Marking)	-	0	OK
6, 6.1(Packing)	-	0	OK

31 Dec, 2026

-
Included w.e.f. 28.03.2024

IS 2581 (2002)

Round strand galvanized steel wire ropes for shipping purposes - Specification (Fourth Revision)

8150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon- IS 228)	-	500	50 grams chips
6.1(Manganese - IS 228)	-	500	50 grams chips
6.1(Silicon - IS 228)	-	500	50 grams chips
6.1(Sulphur - IS 228)	-	500	50 grams chips
6.1(Phosphorus - IS 228)	-	500	50 grams chips
6.1(Copper-IS 228)	-	500	50 grams chips
6.1(Nickel - IS 228)	-	500	50 grams chips
6.1(Chromium - IS 228)	-	500	50 grams chips
6.1(P + S - IS 228)	-	0	NIL
7,11.2 as per IS 1835 (Uniformity of Zinc Coating-IS 2633)	-	1000	2 metre
7,11.3 as per IS 1835 (Mass of Zinc Coating-IS 6745)	-	1500	2 metre

31 Dec, 2026

-
-

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

All grades

9720 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Thickness of sheet/strip)	-	0	Nil
6(Depth of bowl)	-	0	Nil
6(Internal dimensions of the bowl)	-	0	Nil
6(Bowl locating limits)	-	0	Nil
6(Co-ordinating sizes)	-	0	Nil
7.1(Consruction and workmanship)	-	600	Nil
7.1.1(Consruction and workmanship)	-	0	Nil
7.2(Consruction and workmanship)	-	0	Nil
7.2.1(Consruction and workmanship)	-	600	Nil
7.3(Drainers)	-	600	Nil
7.4(Waste outlet)	-	0	nil
7.5(Tap holes)	-	0	Nil
7.6(Overflows)	-	0	Nil
8(Finish)	-	600	Nil
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Carbon Content)	-	500	Sample Size 30X50mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Silicon Content)	-	500	Sample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Manganese Content)	-	500	Sample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nickel Content)	-	500	Sample Size 30X50mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Chromium Content)	-	500	Sample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Sulphur Content)	-	500	ample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Phouphorous Content)	-	500	ample Size 30X100mm sheet
Cl. 5 , As per IS 5522-2014, Cl. 7.2 , Table 1 & 2 Grade Desig X-04-Cr-19-Ni-19 (Numeric Symbol 304)(Nitrogen Content)	-	500	ample Size 30X100mm sheet

31 Dec, 2026

-
-

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

All Type

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 & 13.2 Table-1 (mech)(Diameter of Aluminium Wires After Stranding)	-	1000	For 6 Conductors
8.1.1 & 13.2 Table 2 (mech)(Diameter of Steel Wires After Stranding)	-	1000	for Steel Wire (7 or 1)
13.8 Table-4 (elec)(Lay Ratio- Aluminium Wire Outermost Layer)	-	400	-
13.8 Table-4 (elec)(Lay Ratio- Steel Core (6 Wire Layer))	-	400	-
13.6 (elec)(Resistance test-Aluminium wire after stranding)	-	800	-
13.3 Table 1 (mech)(Breaking Load of Aluminium Wires After Stranding)	-	1600	-
13.3 Table 2 (elec)(Breaking Load of Steel Wires After Stranding)	-	1600	-
13.3 Table 1 (elec)(Breaking Load of Steel Wires After Stranding)	-	1600	-
13.4.2 (elec)(Ductility by Elongation Test after stranding)	-	600	-
13.5.1 (mech)(Wrapping Test Aluminium Wires After Stranding)	-	500	-
13.5.2 (elec)(Wrapping Test Galvanized Steel Wires After Stranding)	-	500	-
13.7.2 (elec)(Uniformity of Zinc coating)	-	1300	-
13.7.2 (elec)(Mass of Zinc coating)	-	700	-

31 Dec, 2026

-
Exclusion: Cl.13.9 (Surface condition test), Cl.13.10 (ultimate breaking load), Cl.13.11 (Stress strain test)

IS 2721 (2003)

Galvanized steel chain link fence fabric - Specification (Second Revision)

6840 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6.1, 6.2, Table 1(Mesh Size)	-	600	-
Cl.6.3, Table 1(Width of the fabric)	-	600	-
Cl.6.3, Table 1(Length of the fabric)	-	600	-
Cl.6.1, 6.2, Table 1(Nominal Dia of Mesh wire)	-	600	-
Cl. 7.2 and Table 1(Line Wire (Diameter))	-	600	-
Cl. 7.2 and Table 1(Line Wire (Number of wires))	-	600	-
Cl.9.1.1(Tensile test of mesh and line wires- IS 1608)	-	600	-
Cl.9.1.2(Wrapping test of mesh and line wires-IS 1755)	-	600	-
Cl.9.1.3(Twist test of mesh and line wires-IS 1717)	-	600	-
Cl.9.1.4(Bend test of mesh and line wires- IS 1608)	-	600	-
Cl.9.2(Line wire (Mass of zinc coating)- IS 6745)	-	1020	-
Cl.8(Chain link fence fabric(Mass of zinc coating)- IS 6745)	-	1020	-
Cl.9.2(Line Wire (Uniformity of Zinc coating)-IS 2633)	-	1020	-
Cl.8(Chain link fence fabric (Uniformity of Zinc coating)-IS 2633)	-	1500	-

31 Dec, 2026

-
-

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

All grade

9180 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Manganese %)	-	500	solid sample size 50X50X20mm
6.1(Phosphorus %)	-	500	solid sample size 50X50X20mm
6.1(Silicon %)	-	500	solid sample size 50X50X20mm
6.1(Sulphur %)	-	500	solid sample size 50X50X20mm
Cl 10.1(Workmanship)	-	0	IS No.2830-2012 (RA2017) ,Cl.No,9 Freedom Defects-Nil,Cl.10 (a)Macro examination - Test Charges-Rs1200/-,Cl No.10(b)Sulphur print test -Test Charges-Rs 2400/, Cl No10.2 ,Test charges-Rs600/-,Cl.No.10.3, Camber Test charges Rs 600/-,Cl.11,Dimensions -Test
Cl 10.1.b)(Workmanship)	-	2400	-
Cl 10.1.a)(Workmanship)	-	1200	-
Cl 10.2(Press)	-	600	-
Cl 10.3(Workmanship)	-	600	-
Cl 11(Length, Width & Thickness)	-	600	-
Cl 9(Workmanship)	-	0	-
6.1(Carbon %)	-	500	solid sample size 50X50X20mm
6.1( Copper %)	-	500	solid sample size 50X50X20mm
6.1( Aluminium %)	-	500	solid sample size 50X50X20mm
6.1( Nb)	-	500	solid sample size 50X50X20mm
6.1(V)	-	500	solid sample size 50X50X20mm
6.1(Cr)	-	500	solid sample size 50X50X20mm
6.1(Mo)	-	500	solid sample size 50X50X20mm
6.1(Ni)	-	500	solid sample size 50X50X20mm
6.1(Nitrogen%)	-	500	solid sample size 50X50X20mm
6.1( Ti)	-	500	-

31 Dec, 2026

-
-

IS 2074 (2015)

Ready mixed paint, air drying, red oxide - Zinc chrome, priming - Specification (Third Revision)

All

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1 (a)(Composition, Pigment, Cl 5.1.1)	-	1000	Sample Size: 500ml along with suitable thinner 500ml in tin container
Cl 5.1 .1 (a)(Zinc chrome, (Type 2 of IS 51), Annex B)	-	1000	Sample Size: 500ml along with suitable thinner 500ml in tin container
Cl 5.1 .1 (b)(Synthetic red oxides of iron (conforming to Grade 2 or IS 44), (conforming to Grade 3 of IS 44), 6 of IS 6947 (Part 2))	-	1000	Sample Size: 500ml along with suitable thinner 500ml in tin container
Cl 5.3(Compatibility with Thinner, IS 1872)	-	300	Sample Size: 500ml along with suitable thinner 500ml in tin container
Cl 5.1.2(Volatile vehicle)	-	1000	Sample Size: 500ml along with suitable thinner 500ml in tin container
Cl 5.4(Freedom from Objectionable Impurities)	-	300	Sample Size: 500ml along with suitable thinner 500ml in tin container
Cl 5.5(Lead Restriction, IS 101(Part 8/Sec 5))	-	1000	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (i) (a) Table 1(Consistency, Annex C)	-	300	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (i) (b) Table 1(Viscosity by ford cup No. 4, IS 101 (Part1/sec5))	-	300	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (ii) Table 1(Mass, IS 101 (Part1/sec7))	-	250	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (iii) (a) Table 1(Drying time, Surface Dry, IS 101 (Part3/sec1))	-	800	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (iii) (b) Table 1(Drying time, Hard Dry, IS 101 (Part3/sec1))	-	800	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (iv) (a) Table 1(Finish, IS 101 (Part3/sec4))	-	250	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (iv) (b) Table 1(Gloss, IS 101 (Part4/sec4))	-	500	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (v) Table 1(Fineness of grind, IS 101 (Part 3/Sec 5))	-	500	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (vi) Table 1(Colour, IS 101 (Part 4/Sec 2))	-	250	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (vii) (a) Table 1(Flexibility and adhesion: Bend test (with 6.25 mm dia mandrel and in type 1 apparatus), Clause 2 of IS 101 (Part 5/Sec 2))	-	500	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (vii) (b) Table 1(Scratch hardness (load 1 000g), Clause 3 of IS 101 (Part 5/Sec 2))	-	500	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (viii) Table 1(Flash point, IS 101 (Part l/Sec 6))	-	500	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (ix) Table 1(Volume solids, IS 101 (Part 8/Sec 6))	-	1000	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (x) (a) Table 1(Resistance to humidity under condition of condensation: Resistance to humidity, Clause 2 of IS 101 (Part 6/Sec 1))	-	9900	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (x) (b) Table 1(Resistance to humidity under condition of condensation: Resistance to sea water (applicable for marine paints only), Annex D)	-	9900	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (x) (c) Table 1(Resistance to humidity under condition of condensation: Resistance to salt spray, Annex E)	-	9900	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (xi) Table 1(Accelerated storage stability test, Annex F)	-	2000	Sample Size: 500ml along with suitable thinner 500ml in tin container
1 (xii) Table 1, Cl.5.6(Keeping properties 1. Visual observation [Cl.3.1, table 1 of IS 101 (Part 6/Sec 2)])	-	5000	Sample Size: 2X 500ml along with suitable thinner 500ml in tin container

31 Dec, 2026

-
REVISED VERSION OF IS 2074:2015 VERSION INCLUDED.

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

All type Solid samples

4550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 18(Weight)	-	120	Sample size 1metre
Cl 15(Length, Width & Thickness)	-	180	Sample size 1metre
Cl 11.3(Press)	-	600	Sample size 0.5metre
Cl 10.3(UTM)	-	600	Sample size 0.5metre
Cl 12(Sudden Load Applied)	-	360	Sample size 100mm
Cl 7(Workmanship)	-	0	Sample size 1metre
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E650, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E650, NITROGEN)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E650 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E650, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E650, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E650, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min)
Clause - 5, 8.1 & 8.2(E600, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E600, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E600, NITROGEN)	-	400	SSample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E650, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E600 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E600, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min)
Clause - 5, 8.1 & 8.2(E600, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E600, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550, NITROGEN)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E550, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450, NITROGEN)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E450, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	500	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410, SILICON)	-	500	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410, NITROGEN)	-	500	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E410, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350, NITROGEN)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E350, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300, NITROGEN)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E300, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E275, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E275, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E275 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E275, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250, CARBON +EQUIVELENT )	-	0	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250, SILICON)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250, NITROGEN)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250 ,MANGANESE)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250, PHOSPHURS)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250, SULPHUR)	-	400	Sample size 20X75xx0.5mm (Min) by OES
Clause - 5, 8.1 & 8.2(E250, CARBON)	-	400	Sample size 20X75xx0.5mm (Min) by OES

31 Dec, 2026

-
Exclusion: Cl.13 (Y Groove cracking test)

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

all grades

4700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(S)	-	750	Sample Size: 50 g chips sample
4(P)	-	750	Sample Size: 50 g chips sample
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.00 to 2.24 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 0.2.80 to 3.15 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Hard Core)	-	850	sample size : 2 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Hard Core For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Hard Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Soft Core)	-	1250	sample size : 3 metre
9.2 referes to IS 4826, Table 1(Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Hard Core)	-	850	sampe size 3 metre
5(b) Tensile Grade)	-	0	-
6(a) Lay)	-	500	-
6(b) Construction)	-	500	-
7(Freedom from defects)	-	0	-
9(a) Tensile)	-	500	-
9(b) Elongation)	-	850	-
9(a) Tensile)	-	500	-

31 Dec, 2026

-
-

IS 4454 : Part 1 (2001)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

Grade SL,SM, SH, DM, DH

9100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	4200	-
7.1, 7.2(copper)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(Vanadium)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(phosphorus)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(sulphur)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(manganese)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(silicon )	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(carbon)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(Chromium)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(nitrogen)	-	500	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(cu + cr + ni)	-	0	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(sulphur + phosphorus)	-	0	Sample size 8 mm dia above using Optical Emission Spectrometer
7.1, 7.2(cu + cr+ni)	-	0	Sample size 8 mm dia above using Optical Emission Spectrometer
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	600	Sample size 8 mm dia above using Optical Emission Spectrometer

31 Dec, 2026

-
-

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

6900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Tensile Test On UTM)	-	720	-
9.2(Wrapping Test)	-	720	-
9.3(Bend test)	-	720	-
6 AND AS PER IS 7887(CARBON)	-	500	100 grams chips/drillings upto 8mm dia by IS 228 and 8mm dia above 50mm lenghtX3 specimen by IS 8811
6 AND AS PER IS 7887(SILICON)	-	500	100 grams chips/drillings upto 8mm dia by IS 228 and 8mm dia above 50mm lenghtX3 specimen by IS 8811
6 AND AS PER IS 7887(MANGANESE)	-	500	100 grams chips/drillings upto 8mm dia by IS 228 and 8mm dia above 50mm lenghtX3 specimen by IS 8811
6 AND AS PER IS 7887(PHOSPHORUS)	-	500	100 grams chips/drillings upto 8mm dia by IS 228 and 8mm dia above 50mm lenghtX3 specimen by IS 8811
6 AND AS PER IS 7887(SULPHUR)	-	500	100 grams chips/drillings upto 8mm dia by IS 228 and 8mm dia above 50mm lenghtX3 specimen by IS 8811
6 AND AS PER IS 7887(ALUMINIUM)	-	1000	100 grams chips/drillings upto 8mm dia by IS 228 and 8mm dia above 50mm lenghtX3 specimen by IS 8811
6 AND AS PER IS 7887(MICRO ALLOY)	-	1000	100 grams chips/drillings upto 8mm dia by IS 228 and 8mm dia above 50mm lenghtX3 specimen by IS 8811

31 Dec, 2026

-
-

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

All grade

7650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
Cl. 6.1, Table 1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	270	NIL
9( FREEDOM FROM DEFECTS)	-	0	NIL
10.1.a)( Macro examination IS 11371)	-	1200	NIL
10.1.b)( Sulphur print tests IS 12037)	-	2400	NIL
11 & 12(DIMENSIONS and Tolerances)	-	0	NIL
11(Dimensions)	-	0	NIL
10.2(Bend)	-	600	NIL
10.3(Chamber)	-	600	NIL

31 Dec, 2026

-
-

IS 2339 (2013)

Aluminium paints for general purposes - Specification (First Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Composition)	-	1000	Suitable thinner can be supplied
5.2(Lead Restriction)	-	1100	-
5.3/8.1 (i)(Drying time)	-	200	-
5.3/8.1 (iv)(Mass)	-	800	-
5.3/8.1 (v)(Wet opacity)	-	800	-
5.3/8.1 (vi)(Flexibility and adhesion, bend test)	-	800	-
5.3/8.1 (vii)(Resistance to humidity under condition of condensation)	-	6000	-
5.3/8.1 (viii)(Flash point)	-	1000	-
5.3/8.1 (ix)(Keeping properties)	-	4000	-

31 Dec, 2026

-
REVISED VERSION OF IS 2339:2013 VERSION INCLUDED.

Bureau of Indian Standards

The National Standards Body of India

MSME TESTING CENTRE, CHENNAI

65/1, GST Road, Guindy, Chennai, Chennai, Tamil Nadu, 600032

9445662299 dctc-sr@dcmsme.gov.in

Scope List