BIS - LIMS (Laboratory Information Management System)

Vimta Labs Limited (6132436), Hyderabad

Plot No.11/6, road No. 9, IDA, Nacharam, Rangareddy, Keesara, Hyderabad, Medchal Malkajgiri, Telangana, 500076

9704156476 satyam.goddumarri@vimta.com

Scope List

Reset

12 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 14203 (2023)

FIRE RESISTING RECORD PROTECTION CABINETS SPECIFICATION Second Revision of IS 14203

264999.99 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3 and 6 (Table 1)(Nominal Sizes - Height)	-	4999.99	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	5000	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	5000	-
7(Designation)	-	5000	-
8.1(Cabinet Construction)	-	4999.98	-
8.2(Locking Mechanism)	-	5000	-
8.3(Locks)	-	5000	-
8.4(Handles)	-	5000	-
9(Internal Fixtures)	-	5000	-
10.1(Minimum overall thinckness of coating)	-	5000	-
11, Annex-B, 3.1(Fire Endurance Test)	-	170000	-
11, Annex-B, 3.2(Fire and Impact test)	-	100000	-
3 and 6 (Table 1)(Height of Pedestal)	-	5000	-
10.2(Cross Hatch Test)	-	15000	-
3 and 6 (Table 1)(Nominal Sizes - Height)	-	5000	-
3 and 6 (Table 1)(Nominal Sizes - Width)	-	5000	-
3 and 6 (Table 1)(Nominal Sizes - Depth)	-	5000	-
7(Designation)	-	5000	-
8.1(Cabinet Construction)	-	5000	-
8.2(Locking Mechanism)	-	5000	-
8.3(Locks)	-	5000	-
8.4(Handles)	-	5000	-
9(Internal Fixtures)	-	5000	-
10.1(Minimum overall thinckness of coating)	-	5000	-
11, Annex-B, 3.1(Fire Endurance Test)	-	170000	-
11, Annex-B, 3.2(Fire and Impact test)	-	100000	-
3 and 6 (Table 1)(Height of Pedestal)	-	5000	-
10.2(Cross Hatch Test)	-	15000	-

25 Oct, 2027

-
Included w.e.f. 11.08.2026

IS 17566 (2021)

Key locks for security Equipment-Specification

200000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE NO-5(CONSTRUCTION)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (i)"(Body of lock, Bolts, Stump)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (ii)"(Lock lever)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (iii)"(Lever springs)	-	15000	-
"CLAUSE NO-6 TABLE NO -1(iv)"(Keys)	-	15000	-
CLAUSE NO -8.1(Endurance Test)	-	100000	-
CLAUSE NO -8.2(Bolt forcing test)	-	20000	-
CLAUSE NO -8.3(Salt Spray Corrosion Test)	-	30000	-
CLAUSE NO -8.4(Key Strength Test)	-	10000	-
CLAUSE NO -9(Marking)	-	5000	-
CLAUSE NO-5(CONSTRUCTION)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (i)"(Body of lock, Bolts, Stump)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (ii)"(Lock lever)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (iii)"(Lever springs)	-	15000	-
"CLAUSE NO-6 TABLE NO -1(iv)"(Keys)	-	15000	-
CLAUSE NO -8.1(Endurance Test)	-	100000	-
CLAUSE NO -8.2(Bolt forcing test)	-	20000	-
CLAUSE NO -8.3(Salt Spray Corrosion Test)	-	30000	-
CLAUSE NO -8.4(Key Strength Test)	-	20000	-
CLAUSE NO -9(Marking)	-	5000	-
CLAUSE NO-5(CONSTRUCTION)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (i)"(Body of lock, Bolts, Stump)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (ii)"(Lock lever)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (iii)"(Lever springs)	-	15000	-
"CLAUSE NO-6 TABLE NO -1(iv)"(Keys)	-	15000	-
CLAUSE NO -8.1(Endurance Test)	-	100000	-
CLAUSE NO -8.2(Bolt forcing test)	-	20000	-
CLAUSE NO -8.3(Salt Spray Corrosion Test)	-	30000	-
CLAUSE NO -8.4(Key Strength Test)	-	20000	-
CLAUSE NO -9(Marking)	-	5000	-
CLAUSE NO-5(CONSTRUCTION)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (i)"(Body of lock, Bolts, Stump)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (ii)"(Lock lever)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (iii)"(Lever springs)	-	15000	-
"CLAUSE NO-6 TABLE NO -1(iv)"(Keys)	-	15000	-
CLAUSE NO -8.1(Endurance Test)	-	100000	-
CLAUSE NO -8.2(Bolt forcing test)	-	20000	-
CLAUSE NO -8.3(Salt Spray Corrosion Test)	-	30000	-
CLAUSE NO -8.4(Key Strength Test)	-	10000	-
CLAUSE NO -9(Marking)	-	5000	-
CLAUSE NO-5(CONSTRUCTION)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (i)"(Body of lock, Bolts, Stump)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (ii)"(Lock lever)	-	15000	-
"CLAUSE NO-6 TABLE NO -1 (iii)"(Lever springs)	-	10000	-
"CLAUSE NO-6 TABLE NO -1(iv)"(Keys)	-	10000	-
CLAUSE NO -8.1(Endurance Test)	-	100000	-
CLAUSE NO -8.2(Bolt forcing test)	-	10000	-
CLAUSE NO -8.3(Salt Spray Corrosion Test)	-	30000	-
CLAUSE NO -8.4(Key Strength Test)	-	15000	-
CLAUSE NO -9(Marking)	-	5000	-

25 Oct, 2027

-
Included w.e.f 04.11.2025

IS 11188 : Part 1 (2021)

Vault Strong Room doors Part 1 specification

350000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Type)	-	5000	-
5 Table 1(bolts, Min)	-	15000	-
5 Table 1(xix) Depth of engagement of shooting)	-	5000	-
5 Table 1(cross sectional area, Min,sq mm)	-	5000	-
5 Table 1(xviii) Diameter of shooting bolts, Min)	-	5000	-
5 Table 1(xvi) Number of shooting bolts at top,Min)	-	5000	-
5 Table 1(xv) Number of shooting bolts on opposite side,Min)	-	5000	-
5 Table 1(xiv) Number of shooting bolts on hinge side, Min)	-	5000	-
5 Table 1(xiii) Number of locks)	-	5000	-
5 Table 1(xii) Wall thickness (recommendation))	-	5000	-
5 Table 1(xi) Thickness of drill and oxyacetylene torch resisting layer (excluding mild steel plates),Min)	-	5000	-
5 Table 1(ix) Thickness of doors slab, thickness over rebate)	-	5000	-
5 Table 1(viii) Pitch of grill gate rods)	-	5000	-
5 Table 1(vii) Diameter of grill gate rods, Min)	-	5000	-
5 Table 1(vi) Thickens of grill gate angles or section made out of M.S. plates, Min)	-	5000	-
5 Table 1(v) Dimension of the rebate coming under shear)	-	5000	-
5 Table 1(iv (b) Thickness of door frame, if fabricated from single plate to form channel/multi-bend section, Min)	-	5000	-
5 Table 1(ii (a) Height H, Min b) Width W, Min iv(a) Thickness of door frame angle, channel or section made out of M.S. plates, if built up to form a channel,Min)	-	15000	-
5 Table 1(iii) Inside dimension or clear opening when door shutters are swung open at 180 degree)	-	15000	-
5 Table 1(ii (b) Width W)	-	10000	-
5 Table 1(ii (a) Height, H)	-	5000	-
5 Table 1(ii) Overall dimension of vault door)	-	5000	-
5 Table 1(i) Door Type)	-	5000	-
5(Table-1)(Type of Door)	-	3000	-
6(Materail)	-	3000	-
7(Classification)	-	5000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	5000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	5000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	5000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	5000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	5000	-
8.2.1(Rebate of the door frame)	-	5000	-
8.2.2(Compression mechanism)	-	5000	-
8.2.3(Crane hinge mechanism)	-	5000	-
8.3(Lock case)	-	5000	-
8.3.2(Bolt work)	-	5000	-
8.3.2.2(Construction (of bolt work))	-	5000	-
8.3.2.3(Bearing piller)	-	5000	-
8.4.1(Shooting bolt control (By lock))	-	5000	-
8.4.2(Test of key-Lock)	-	25000	-
8.4.3(Lock fixing bolts)	-	5000	-
8.4.4(Time lock)	-	5000	-
8.4.5(Automatic Relocking devise)	-	5000	-
9 &9.1(Hinges)	-	5000	-
9.1.1(Adjusting bolt)	-	5000	-
9.2(Handles)	-	5000	-
9.3(Foot bringe)	-	5000	-
9.4(Vault lighting control)	-	5000	-
10 &10.1(Dents,Burrs & Edges)	-	5000	-
10.2(Colour coating thickness (Surafce paint))	-	5000	-
10.3(Cross Hatch test)	-	5000	-
10.4(Door (Stainless cladding))	-	5000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	170000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	220000	-
12(Marking of door)	-	5000	-
12.2(Marking on keys)	-	5000	-
11.1 (1)(Burglary resistance IS 11188 (Part 2))	-	170000	-
11.1 (3)(Fire and stream hose IS 11188 (Part 3))	-	120000	-
11.1 (2)(Fire endurance IS 11188 (Part 3))	-	130000	-
10.4(Alternate to Cl 10.4)	-	5000	-
10.3(Cross Hatch Test)	-	15000	-
10(FINISH)	-	5000	-
9.4(Vault Lighting Control)	-	5000	-
9.3(Foot Bridge)	-	5000	-
9.2(Handles)	-	5000	-
9.1.1(Adjusting Bolt)	-	5000	-
9.1(Hinges)	-	5000	-
9(DOOR FITTINGS)	-	5000	-
8.4.5(Automatic Relocking Device)	-	5000	-
8.4.4(Time Lock)	-	5000	-
8.4(Lock)	-	5000	-
8.3.2.2(Construction)	-	5000	-
8.3.2.1(The number of bolts and their minimum dimension)	-	5000	-
8.3.2(Bolt Work)	-	5000	-
8.3.1(Lock Case)	-	5000	-
8.3(Locking Mechanism)	-	5000	-
8.2.3(Crane Hinge Mechanism)	-	5000	-
8.2.2(Compression Mechanism)	-	5000	-
8.2.1(Rebate of the Door Frame)	-	5000	-
8.2(Doors Frame)	-	5000	-
8.1.2(Main Door (Outside))	-	5000	-
8.1.1(Ventilating Grill Gate (Inside))	-	5000	-
8.1 Fig. 1(Doors)	-	5000	-
8(CONSTRUCTION AND GENERALREQUIREMENTS)	-	5000	-
5(Table-1)(Overall dimesion of door)	-	5000	-
5(Table-1)(Inside dimension or clear opening of door)	-	5000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	5000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	5000	-
5(Table-1)(Dimension of the rebate coming under share)	-	5000	-
5(Table-1)(Thickness of grill gate angle/section)	-	5500	-
5(Table-1)(Diameter of grill gate rod)	-	5000	-
5(Table-1)(Pitch of grill gate rod)	-	5000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	5000	-
5(Table-1)(Thickness of the door over lock)	-	5000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	5000	-
5(Table-1)(Wall thickness)	-	5000	-
5(Table-1)(Number of locks)	-	5000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	5000	-
5(Table-1)(Number of shooting bolts on opposite)	-	5000	-
5(Table-1)(Number of shooting bolts at top)	-	5000	-
5(Table-1)(Number of shooting bolts at bottom)	-	5000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	5000	-
5(Table-1)(Depth engagement of shooting)	-	5000	-
4(Type)	-	5000	-
5(Table-1)(5(Table-1))	-	5000	-
5(Table-1)(Overall dimesion of door)	-	5000	-
5(Table-1)(Inside dimension or clear opening of door)	-	5000	-
5(Table-1)(Thickness of door frame angle-made of Plate,if bulit up to form a channel)	-	5000	-
5(Table-1)(Thickness of door frame ,if fabricated or multibend)	-	5000	-
5(Table-1)(Dimension of the rebate coming under share)	-	5000	-
5(Table-1)(Thickness of grill gate angle/section)	-	5000	-
5(Table-1)(Diameter of grill gate rod)	-	5000	-
5(Table-1)(Pitch of grill gate rod)	-	5000	-
5(Table-1)(Thickness of door slab,thickness over rebate)	-	5000	-
5(Table-1)(Thickness of the door over lock)	-	5000	-
5(Table-1)(Thickness of drill & oxyacetylene torch resis. layer(exclue MS plate)	-	5000	-
5(Table-1)(Wall thickness)	-	5000	-
5(Table-1)(Number of locks)	-	5000	-
5(Table-1)(Number of shooting bolys on hinge side)	-	5000	-
5(Table-1)(Number of shooting bolts at top)	-	5000	-
5(Table-1)(Number of shooting bolts at bottom)	-	5000	-
5(Table-1)(Cross sectional area as per shooting bolt)	-	6000	-
5(Table-1)(Depth engagement of shooting)	-	5000	-
6(Materail)	-	5000	-
7(Classification)	-	5000	-
8 & 8.1.1(Ventilating Grill Gate (Inside))	-	5000	-
8.1.1.1(Locking device (unpickable dual control lock))	-	5000	-
8.1.2(Main Door- Outer & inner plate thickness)	-	5000	-
8.1.2.1(Door(Finish &Gap of frame/edge with any place))	-	5000	-
8.2(Door frame (No.of barckets & Size for gripping))	-	5000	-
8.2.1(Rebate of the door frame)	-	5000	-
8.2.2(Compression mechanism)	-	5000	-
8.2.3(Crane hinge mechanism)	-	5000	-
8.3(Lock case)	-	5000	-
8.3.2(Bolt work)	-	5000	-
8.3.2.2(Construction (of bolt work))	-	5000	-
8.3.2.3(Bearing piller)	-	5000	-
8.4.1(Shooting bolt control (By lock))	-	5000	-
8.4.2(Test of key-Lock)	-	25000	-
8.4.3(Lock fixing bolts)	-	5000	-
8.4.4(Time lock)	-	5000	-
8.4.5(Automatic Relocking devise)	-	5000	-
9 &9.1(Hinges)	-	5000	-
9.1.1(Adjusting bolt)	-	5000	-
9.3(Foot bringe)	-	5000	-
9.4(Vault lighting control)	-	5000	-
10 &10.1(Dents,Burrs & Edges)	-	5000	-
10.2(Colour coating thickness (Surafce paint))	-	5000	-
10.3(Cross Hatch test)	-	25000	-
10.4(Door (Stainless cladding))	-	5000	-
11.1 &11.2(Test criteria for confomity -Burglaty attack)	-	170000	-
11.1 &11.2(Test criteria for confomity -Fire resistancey)	-	220000	-
12(Marking of door)	-	5000	-
12.2(Marking on keys)	-	5000	-

25 Oct, 2027

-
-

IS 550 : Part 1 (2022)

Safes: Part 1 specification Fifth Revision

380000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	5000	-
5.1(Dimensions)	-	5000	-
5.2(Sizes)	-	5000	-
6(Material declaration)	-	5000	-
7(Desigantion-Delaration)	-	5000	-
8.1(Body (Construction & workmanship))	-	5000	-
8.2(Door (Gap))	-	5000	-
8.4.1(Hinges)	-	5000	-
8.4.2(Bolts)	-	5000	-
8.5(Handle)	-	5000	-
8.6.1(Lock (key type) Garde)	-	5000	-
8.8(Cable hole size)	-	5000	-
9(Internal fixture)	-	5000	-
10(Painting)	-	5000	-
10.1(Cross hatch test)	-	5000	-
11.1(Marking of safe)	-	5000	-
12(Burglary attack)	-	150000	-
12(Fire Resistance)	-	150000	-

25 Oct, 2027

-
-

IS 5244 (2020)

Safe Deposit Locker Cabinets — Specification ( Fourth Revision )

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4.1( Types )	-	1000	-
Cl. 6 (Fig-5)(Cabinet Size (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Finish)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.2(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.4(Design and Manufacture)	-	1000	-
Cl. 7.5(Design and Manufacture)	-	1000	-
Cl. 7.6(Design and Manufacture)	-	1000	-
Cl. 8(Workmanship)	-	1000	-
Cl. 8.2(Tolerance)	-	1000	-
Cl. 9.1(Testing)	-	25000	-
Cl. 9.2(Testing)	-	20000	-
Cl. 9.3(Cross Hatch Test)	-	20000	-
Cl. 10.1(Marking)	-	1500	-
Cl. 10.2(Marking)	-	1500	-
Cl. 10.3(Marking)	-	1500	-
Cl. 10.4(Marking on Keys)	-	1500	-
Cl. 11(Packing)	-	1500	-
Cl. 4.1( Types )	-	1000	-
Cl. 6 (Fig-5)(Cabinet Size (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Finish)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.2(Design and Manufacture)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl. 7.4(Design and Manufacture)	-	1000	-
Cl. 7.5(Design and Manufacture)	-	1000	-
Cl. 7.6(Design and Manufacture)	-	1000	-
Cl. 8(Workmanship)	-	1000	-
Cl. 8.2(Tolerance)	-	1000	-
Cl. 9.1(Testing)	-	25000	-
Cl. 9.2(Testing)	-	25000	-
Cl. 9.3(Cross Hatch Test)	-	20000	-
Cl. 10.1(Marking)	-	1500	-
Cl. 10.2(Marking)	-	1500	-
Cl. 10.3(Marking)	-	1500	-
Cl. 10.4(Marking on Keys)	-	1500	-
Cl. 11(Packing)	-	1500	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Finish)	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Cl. 9.2(Testing)	-	20000	-
Cl. 10.1(Marking)	-	1000	-
Cl. 7.3(Design and Manufacture)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl.6(Sizes (Minimum Inside Measurements of locker) Locker Size)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Cl. 7.1(Design and Manufacture)	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Finish)	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-
Table 1(Thickness Min. (in mm))	-	1000	-

25 Oct, 2027

-
-

IS 14203 (2017)

Fire resisting record protection cabinets - Specification (Second Revision)

340000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Nominal Sizes)	-	5000	-
4(Types)	-	5000	-
5(i) Steel components)	-	5000	-
6(a) Heght)	-	5000	-
6(b) Width)	-	5000	-
6(c) Depth)	-	5000	-
7(Designation)	-	5000	-
8(General Constructions)	-	5000	-
8.1(Cabinet construction)	-	5000	-
8.1(i) Outer body and inner box shall be fabricated from mild steel or galvanised steel sheets of not less than 0.8 mm nominal thickness. The steel parts shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	5000	-
8.1(The cabinet body of the fire resisting record protection cabinet shall be of double wall type with insulating material filled in-between. The insulating material should not produce toxic gases when the cabinet is exposed to fire situation The components shall be assembled by bolting, welding, riveting or by any combination of these methods)	-	5000	-
8.2(Locking Mechanism: The locking mechanisms shall be of 4 way type. The diameter of shooting bolts shall be 15 mm to 20 mm. There shall be minimum three shooting bolts (two shooting bolts for size 1 000) on each side and minimum one vertical shooting bolt each on top and bottom. The shooting bolts shall slide smoothly in recess and engage in body to a minimum depth of 12 mm.)	-	5000	-
8.3(Locks: The cabinet shall be supplied with a dual control key lock having minimum 6 levers with duplicate keys. The keys shall be made of stainless steel or any other non ferrous metal/alloy having non-corrosive properties. Minimum two sets of the keys shall be supplied. Alternatively three wheel combination locks in place of key lock or both may be provided, if required by the purchaser. purchaser)	-	5000	-
8.4(Handles: Handle shall be made from ferrous (powder coated/ plated), non-ferrous material or polymer)	-	5000	-
9(Internal Fixtures:)	-	5000	-
9.1(The cabinet shall be provided with minimum four shelves for nominal size 1 600, three shelves for nominal size 1 300 and two shelves for cabinets of nominal size 1 000. Shelf height shall be adjustable)	-	5000	-
9.2(A cabinet may also be provided with drawer unit fitted with any suitable lock)	-	5000	-
10(Painting)	-	5000	-
10.1(i)The inside and outside surfaces of cabinet shall be painted or powder coated. In case of paint an appropriate primer and under coating shall be used in accordance with normal industrial practices)	-	5000	-
10.1(ii)The minimum overall thickness of the coatings shall be 50 microns for powder coatings and 70 microns for liquid paints)	-	5000	-
10.1.1(Cross hatch test shall be conducted to conform the adhesion of coating in accordance with 10.2)	-	5000	-
10.2(Cross Hatch Test: )	-	5000	-
10.2(a) Make 6 parallel cut marks using sharp metal pointer and straight edge, through the painted/ coated surface, so as to make the base surface visible through cut marks.)	-	5000	-
10.2(b)Cut marks shall be minimum 20 mm long and at 2 mm distance from each other.)	-	5000	-
10.2(c)Make 6 similar cut marks in the direction perpendicular to first set of cut marks, with same length and spacing )	-	5000	-
10.2(d) These 12 cut marks together shall make a pattern of 25 squares of 2 mm × 2 mm size, totally separated from each other)	-	5000	-
10.2(e) A good quality transparent adhesive tape not less than 20 mm width, shall be stuck on the pattern, parallel to any one set of cut marks)	-	5000	-
10.2(f) To ensure continuous contact with paint/coat film, rub the tape firmly and remove air bubbles under the tape, if any)	-	5000	-
10.2(g)Within 60 to 120 s after sticking the tape, remove it by seizing free end of the tape and rapidly pulling it off at an angle close to 180°.)	-	5000	-
10.2(h) Painting/Coating quality is considered as acceptable, if no part of any 2 mm × 2 mm square of paint/coat comes off the surface due to pulling the tape)	-	5000	-
11.2(Fire endurance test: The fire resisting record protection cabinets shall be considered to be conforming to the requirements of this standard if they successfully complete the fire endurance test (see B-3.1) and fire and impact test (see B 3.2).)	-	170000	-
11.2.1(The fire resisting record protection cabinets shall be considered to be conforming to the requirements of this standard, if they pass the fire endurance test (see B-3.1) and fire and impact test (see B-3.2) if the contents (see B-1.1, B-3.1.1, B-3.2.1) kept in the cabinets during the test are found usable.)	-	10000	-
12.1(Marking:A metal plate showing type of cabinet together with the manufacturer’s name and the year of manufacture shall be fixed on the inner face of the door)	-	5000	-
12.2(Marking on Keys: The keys shall be marked with an identification number which shall not be the same as the serial number of the cabinet.)	-	5000	-
3(Nominal Sizes)	-	-	-
4(Types)	-	-	-
5(i) Steel components)	-	-	-
6(a) Heght)	-	-	-
6(b) Width)	-	-	-
6(c) Depth)	-	-	-
7(Designation)	-	-	-
8(General Constructions)	-	-	-
8.1(Cabinet construction)	-	-	-
8.1(i) Outer body and inner box shall be fabricated from mild steel or galvanised steel sheets of not less than 0.8 mm nominal thickness. The steel parts shall not have any burrs or dents. If required the outer body shall be suitably stiffened to avoid bulging)	-	-	-
8.1(The cabinet body of the fire resisting record protection cabinet shall be of double wall type with insulating material filled in-between. The insulating material should not produce toxic gases when the cabinet is exposed to fire situation The components shall be assembled by bolting, welding, riveting or by any combination of these methods)	-	-	-
8.2(Locking Mechanism: The locking mechanisms shall be of 4 way type. The diameter of shooting bolts shall be 15 mm to 20 mm. There shall be minimum three shooting bolts (two shooting bolts for size 1 000) on each side and minimum one vertical shooting bolt each on top and bottom. The shooting bolts shall slide smoothly in recess and engage in body to a minimum depth of 12 mm.)	-	-	-
8.3(Locks: The cabinet shall be supplied with a dual control key lock having minimum 6 levers with duplicate keys. The keys shall be made of stainless steel or any other non ferrous metal/alloy having non-corrosive properties. Minimum two sets of the keys shall be supplied. Alternatively three wheel combination locks in place of key lock or both may be provided, if required by the purchaser. purchaser)	-	-	-
8.4(Handles: Handle shall be made from ferrous (powder coated/ plated), non-ferrous material or polymer)	-	-	-
9(Internal Fixtures:)	-	-	-
9.1(The cabinet shall be provided with minimum four shelves for nominal size 1 600, three shelves for nominal size 1 300 and two shelves for cabinets of nominal size 1 000. Shelf height shall be adjustable)	-	-	-
9.2(A cabinet may also be provided with drawer unit fitted with any suitable lock)	-	-	-
10(Painting)	-	-	-
10.1(i)The inside and outside surfaces of cabinet shall be painted or powder coated. In case of paint an appropriate primer and under coating shall be used in accordance with normal industrial practices)	-	-	-
10.1(ii)The minimum overall thickness of the coatings shall be 50 microns for powder coatings and 70 microns for liquid paints)	-	-	-
10.1.1(Cross hatch test shall be conducted to conform the adhesion of coating in accordance with 10.2)	-	-	-
10.2(Cross Hatch Test: )	-	-	-
10.2(a) Make 6 parallel cut marks using sharp metal pointer and straight edge, through the painted/ coated surface, so as to make the base surface visible through cut marks.)	-	-	-
10.2(b)Cut marks shall be minimum 20 mm long and at 2 mm distance from each other.)	-	-	-
10.2(c)Make 6 similar cut marks in the direction perpendicular to first set of cut marks, with same length and spacing )	-	-	-
10.2(d) These 12 cut marks together shall make a pattern of 25 squares of 2 mm × 2 mm size, totally separated from each other)	-	-	-
10.2(e) A good quality transparent adhesive tape not less than 20 mm width, shall be stuck on the pattern, parallel to any one set of cut marks)	-	-	-
10.2(f) To ensure continuous contact with paint/coat film, rub the tape firmly and remove air bubbles under the tape, if any)	-	-	-
10.2(g)Within 60 to 120 s after sticking the tape, remove it by seizing free end of the tape and rapidly pulling it off at an angle close to 180°.)	-	-	-
10.2(h) Painting/Coating quality is considered as acceptable, if no part of any 2 mm × 2 mm square of paint/coat comes off the surface due to pulling the tape)	-	-	-
11.2(Fire endurance test: The fire resisting record protection cabinets shall be considered to be conforming to the requirements of this standard if they successfully complete the fire endurance test (see B-3.1) and fire and impact test (see B 3.2).)	-	-	-
11.2.1(The fire resisting record protection cabinets shall be considered to be conforming to the requirements of this standard, if they pass the fire endurance test (see B-3.1) and fire and impact test (see B-3.2) if the contents (see B-1.1, B-3.1.1, B-3.2.1) kept in the cabinets during the test are found usable.)	-	-	-
12.1(Marking:A metal plate showing type of cabinet together with the manufacturer’s name and the year of manufacture shall be fixed on the inner face of the door)	-	-	-
12.2(Marking on Keys: The keys shall be marked with an identification number which shall not be the same as the serial number of the cabinet.)	-	-	-

25 Oct, 2027

-
-

IS 550 : Part 1 (2014)

Safes: Part 1 specification (Fifth Revision)

380000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4 Table 1(CLASSIFICATIONS)	-	5000	-
Cl. 5 Table 2(DIMENSIONS AND SIZES)	-	5000	-
Cl. 5 Table 10(DIMENSIONS AND SIZES)	-	5000	-
Cl. 7 (DESIGNATIONS)	-	5000	-
Cl. 8.1(Body)	-	5000	-
Cl. 8.3(Door)	-	5000	-
Cl. 8.4.1(Hinges)	-	5000	-
Cl. 8.4.2(Bolts)	-	5000	-
Cl. 8.5 Table 3(Handles)	-	5000	-
Cl. 8.6.1(Locks (Type))	-	5000	-
Cl. 8.6.2(Locks (Levers))	-	25000	-
Cl. 8.6.3(Tests for locks)	-	25000	-
Cl. 8.6.4(Keys)	-	5000	-
Cl. 8.6.5(Unpickability)	-	5000	-
Cl. 8.6.6(Non-interchangeability)	-	5000	-
Cl. 8.7(Automatic Relocking Device)	-	10000	-
Cl. 9(INTERNAL FIXTURES)	-	5000	-
Cl. 10(Painting)	-	5000	-
Cl. 10(Painting)	-	5000	-
Cl. 11.1(Marking of Safes)	-	5000	-
Cl. 11.2( Marking on Keys)	-	5000	-
Cl. 11.3(BIS Certification Marking)	-	5000	-

25 Oct, 2027

-
-

IS 1046 (2014)

Cash boxes - Specification (Fourth Revision)

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-5.1(Fabrication)	-	5000	NA
Clause-5.2(Body)	-	5000	Na
Clause-5.3(Bottom)	-	5000	Na
Clause-5.4(Lid)	-	5000	Na
Clause-5.5(Hinges)	-	5000	Na
Clause-5.6(Bolts)	-	5000	Na
Clause-5.7(Handle)	-	5000	Na
Clause-5.8(Lock)	-	5000	Na
Clause-5.8.1(Levers)	-	5000	Na
Clause-5.8.2(Lever Spring)	-	5000	Na
Clause-5.8.3(Key)	-	5000	Na
Clause-5.8.4(Unpickability)	-	5000	NA
Clause-5.8.5(Non-interchangeability)	-	5000	Na
Clause-6(Internal Fixtures)	-	5000	Na
Clause-8(Marking)	-	5000	Na

25 Oct, 2027

-
-

IS 11188 : Part 1 (2014)

Vault (Strong Room) doors: Part 1 specification (Second Revision)

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table 1(DIMENSIONS)	-	5000	-
5 Table 1(i) Door Type)	-	5000	-
5 Table 1(ii) Overall dimension of vault door)	-	5000	-
5 Table 1( a) Height,H)	-	5000	-
5 Table 1( b) Width W)	-	5000	-
5 Table 1(iii) Inside dimension or clear opening when door shutters are swung open at 180 degree)	-	5000	-
5 Table 1( a) Height H, Min b) Width W, Min iv) a) Thickness of door frame angle, channel or section made out of M.S. plates, if built up to form a channel,Min )	-	5000	-
5 Table 1( b) Thickness of door frame, if fabricated from single plate to form channel/multi-bend section, Min)	-	5000	-
5 Table 1( v) Dimension of the rebate coming under shear)	-	5000	-
5 Table 1( vi) Thickens of grill gate angles or section made out of M.S. plates, Min)	-	5000	-
5 Table 1( vii) Diameter of grill gate rods, Min)	-	5000	-
5 Table 1( viii) Pitch of grill gate rods)	-	5000	-
5 Table 1(ix) Thickness of doors slab, thickness over rebate)	-	5000	-
5 Table 1(xii) Wall thickness (recommendation))	-	5000	-
5 Table 1(xiii) Number of locks)	-	5000	-
5 Table 1(xiv) Number of shooting bolts on hinge side, Min)	-	5000	-
5 Table 1(xv) Number of shooting bolts on opposite side,Min)	-	5000	-
5 Table 1(xvi) Number of shooting bolts at top,Min)	-	5000	-
5 Table 1(xviii) Diameter of shooting bolts, Min)	-	5000	-
5 Table 1(xix) Depth of engagement of shooting)	-	5000	-
8( CONSTRUCTION AND GENERALREQUIREMENTS)	-	5000	-
8.1.1( Ventilating Grill Gate (Inside))	-	5000	-
8.1.2( Main Door (Outside))	-	5000	-
8.2(Doors Frame)	-	5000	-
8.2.1 (Rebate of the Door Frame)	-	5000	-
8.2.2 (Compression Mechanism)	-	5000	-
8.2.3 (Crane Hinge Mechanism)	-	5000	-
8.3(Locking Mechanism)	-	5000	-
8.3.1( Lock Case)	-	5000	-
8.3.2 (Bolt Work)	-	5000	-
8.3.2.1 Table 1.(The number of bolts and their minimum dimension)	-	5000	-
8.4(Lock)	-	5000	-
8.4.5 (Automatic Relocking Device)	-	5000	-
9( DOOR FITTINGS)	-	5000	-
9.1(Hinges)	-	5000	-
9.1.1( Adjusting Bolt)	-	5000	-
9.2( Handles)	-	5000	-
9.3( Foot Bridge)	-	5000	-
10(FINISH)	-	20000	-
10.3( Cross Hatch Test)	-	20000	-
IS 11188 (Part 2), 3.1 and 3.2( i)Net Working time, Minutes)	-	37500	-
IS 11188 (Part 3) Cl4.4(Fire endurance IS 11188 (Part 3))	-	85000	-
IS 11188 (Part 3) Cl 4.5(Fire and stream hose IS 11188 (Part 3))	-	85000	-
11(Burglary resistance IS 11188 (Part 2))	-	37500	-

25 Oct, 2027

-
-

IS 14561 (2014)

Fire resisting (Insulating) filing cabinets - Specification (Second Revision)

335000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Types & Rating)	-	5000	-
3.1(i) The fire resisting filing cabinets shall be of two types: a) Vertical fire resisting filing cabinet, and b) Lateral fire resisting filing cabinet.)	-	5000	-
3.2(ii) The standard and lateral fire resisting filing cabinets shall have one-drawer or two-drawers or three drawers or four-drawers. A typical drawing of the fire resisting filing cabinet is given in Fig. 1.)	-	5000	-
3.3(iii) The fire resisting filing cabinets shall have fire resisting ratings of 60 min or 120 min or 180 min or 240 min)	-	5000	-
4(Dimensions and Tolerances, mm)	-	5000	-
4.1(Overall Dimensions of Fire Resisting Filing Cabinets: The internal usable space of the drawers of fire resisting (insulating) filing cabinets shall be as specified in Table 1 or any other size which is mutually agreed to between the purchaser and the supplier.)	-	5000	-
4.1(Internal usuable space of drawer, mm:)	-	5000	-
4.1(iv) Height of the bottom drawer above floor level)	-	5000	-
6(Designations: The filing cabinet shall be designated by the commonly used name, type, the fire rating and the number of this Indian Standard.)	-	5000	-
7(Constructions)	-	5000	-
7.2(Cabinets Sub-Assembly: The external body and drawer fronts of the fire resisting (insulating) filing cabinet shall be of double wall type with homogeneous insulating material filled in between. Further the construction of the cabinet shall be such that each drawer slides in an individual inner box. The inner boxes shall have a insulating layer between each other to prevent fire spreading from one drawer to another. The joining of inner box, intermediate piece and outer body shall be such that, it forms a cavity to receive drawer front )	-	5000	-
7.3(Filing Drawer: The drawer shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall have an arrangement on the sides suitable for the drawer suspension system and an arrangement to stop it when fully pushed in.)	-	5000	-
7.3.1(Drawer Front: The drawer front shall be made from mild steel or galvanized steel sheet of not less than 0.6 mm and not more than 1.0 mm nominal thickness and shall be firmly secured to the drawer body by welding, screwing or riveting or any combination of these processes. The construction of drawer front shall be such that it snugly fits in the cavity provided for the same )	-	5000	-
7.4.1(Latch: Each drawer of the cabinet shall be removable but shall be fitted with a latch/positive stop to prevent inadvertent withdrawal and rebound. Such latch shall be lifted/unlocked by the pull of the handle or any other mechanism.)	-	5000	-
7.4.2(The locking mechanism shall be designed in such a manner so that there is minimum passage for direct conduction of heat from outside to inside)	-	5000	-
7.5(Drawer Suspension The drawer suspension shall be either of the following types to ensure withdrawal of the full depth of the drawer: a) Ball bearing / Roller bearing suspension (Movement), b) Solid roller suspension, and c) Telescopic slide suspension (Extension)	-	5000	-
7.6(Handles: Each drawer shall be provided either with a handle made from ferrous/non-ferrous material suitably coated for corrosion resistance, or any polymer and fixed to the front of the drawer or with a built in pulling mechanism)	-	5000	-
7.6.1(The drawer handle shall be strong enough to take a minimum pull of 50 N for 2 min. There shall be no sharp corners or edges to avoid injury and damage to clothing)	-	5000	-
7.7.1(Locks: Top drawer shall be provided with single or dual control key lock having not less than 6 levers or pin cylinder lock having not less than 6 pins, with duplicate keys of stainless steel/nonferrous alloy. Alternatively if required by the purchaser a 3 wheel combination lock or electronic combination lock may be provided either in place of key lock or in addition to key lock)	-	5000	-
7.7.2(Each drawer may also be provided with individual key lock or pin cylinder lock or combination lock subject to agreement between the purchaser and the supplier.)	-	5000	-
7.8.1(The locking mechanism shall be such that when the top drawer is pushed-in fully, it actuates locking mechanism to lock all other drawers imultaneously, when they are in pushed-in position)	-	5000	-
7.8.1.1(At the time of locking the cabinet, if one of the drawers is not fully pushed-in, that drawer shall remain unlocked and can be used. As soon as that drawer is pushed-in fully, it shall get locked automatically without further operation of key by the user.)	-	5000	-
7.8.1.2(In addition to the above, isolation mechanism shall also be provided to permit independent locking/ use of other drawers. Such isolation mechanism provided on drawers shall be manually operated)	-	5000	-
8(Assemblies)	-	5000	-
8.1(The components shall be assembled by bolting, welding, riveting or by any combination of these processes)	-	5000	-
8.2(All joints between outer body and inner boxes, the drawer front and the outer body shall be such that, there is minimum direct conduction of heat from outer body to inner body)	-	5000	-
9.1(Drawer Suspension Test and Latch Test: The drawer loaded with evenly distributed load of 30 kg (excluding the weight of drawer) in any drawer shall be operated for 5 000 cycles at a rate of 300 cycles/h ±10 percent. One opening and one closing shall constitute one cycle. The test shall be carried out with maximum two breaks by using electrically or mechanically operated test equipment with a counter fitted on it. After 5 000 cycles the suspension slide and latch mechanism shall not show any apparent distortion, cracks, or failures to operate in a normal smooth manner)	-	5000	-
10.1(Finish: All dents, burrs and sharp edges shall be removed from the various components and they shall be thoroughly degreased and cleaned of rust and scale)	-	15000	-
10.2(The inside and outside surfaces of the fire resisting (Insulating) filing cabinet shall be painted or powder coated. In case of paint, an appropriate primer and undercoating shall be used in accordance to industry practices. The minimum overall thickness of the coatings shall be 50 μ for powder coating and 70 μ for liquid paint. Cross hatch test shall be conducted to confirm the adhesion of coating in accordance with 10.2.1)	-	15000	-
10.2.1(Cross Hatch Test)	-	15000	-
11.1(Fire endurance test)	-	150000	-
11.2(Fire and impact test)	-	100000	-
12.1(Marking of Cabinets:A metal plate showing classification of cabinet together with the manufacturer’s name, serial number and the year of manufacture shall be fixed inside surface of the top drawer of the cabinet in such a way that it is visible when it is opened.)	-	5000	-
12.2(Marking on Keys: The keys shall bear an identification number which shall not be the same as the serial number of the cabinet)	-	5000	-

25 Oct, 2027

-
-

IS 14562 (2014)

Fire resisting computer media protection cabinets - Specification (First Revision)

325000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2(Nominal Size (Declared))	-	5000	NA
3(Type)	-	5000	NA
4(Materail(Declaration))	-	5000	NA
5(Dimension & Tolerance - Nominal Size)	-	5000	NA
5(Nomina Inside dimension - Height)	-	5000	NA
5(Nomina Inside dimension - Width)	-	5000	NA
5(Nomina Inside dimension - Depth)	-	5000	NA
6(Designation)	-	5000	NA
7(Construction)	-	5000	NA
8(Assembly)	-	5000	NA
9.1(Fabrication (Thickness of Internal steelsheet))	-	5000	NA
9.2(Shelf)	-	5000	Na
9.3(Door (Thickness of steel sheet))	-	5000	Na
9.3(Door (Thickness of steel sheet))	-	5000	NA
9.4(Handle)	-	5000	Na
9.5(Compression mechanism)	-	5000	NA
9.6(Weight)	-	15000	NA
10(Sampling (Sample quantity))	-	5000	NA
11(Tests - Fire Resistancy)	-	150000	NA
11(Tests - Fire Resistancy)	-	150000	NA
11.6(Criteria for conformity -Fire Endurance test)	-	50000	NA
11.6(Criteria for conformity -Fire Endurance test)	-	50000	NA
11.6(Criteria for conformity -Fire & Impcat test)	-	50000	NA
11.6(Criteria for conformity -Fire & Impcat test)	-	50000	na
11.6(Criteria for conformity -Fire Endurance test)	-	50000	NA
11.7(Test Report)	-	5000	NA
12.1(Paint-Coating thicknes)	-	25000	Na
12.2(Crotch hatch test)	-	25000	NA
12.3(Finish)	-	5000	NA
13.1(Marking)	-	5000	NA
13.1(Marking on keys)	-	5000	NA

25 Oct, 2027

-
-

IS 17541 (2021)

Modular panel for security of premises specification

C B A AA AAA

546000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause-5(Dimensions)	-	5000	-
Clause-6(Materials)	-	5000	-
Clause-8(Construction and General Requirements)	-	5000	-
Clause-9(Fittings)	-	5000	-
Clause-10(Finish)	-	25000	-
Clause-10.1(Cross Hatch Test)	-	15000	-
Clause-11.2, 1(Full length panel (Continuous design panel))	-	170000	-
Clause-11.2, 2(Assemble panel/Segmented panel)	-	340000	-
Clause-12(Marking)	-	5000	-
Clause-5(Dimensions)	-	5000	-
Clause-6(Materials)	-	5000	-
Clause-8(Construction and General Requirements)	-	5000	-
Clause-9(Fittings)	-	5000	-
Clause-10(Finish)	-	25000	-
Clause-10.1(Cross Hatch Test)	-	15000	-
Clause-11.2, 1(Full length panel (Continuous design panel))	-	170000	-
Clause-11.2, 2(Assemble panel/Segmented panel)	-	340000	-
Clause-12(Marking)	-	5000	-

25 Oct, 2027

-
Included w.e.f. 05.12.2024

Bureau of Indian Standards

The National Standards Body of India

Vimta Labs Limited (6132436), Hyderabad

Plot No.11/6, road No. 9, IDA, Nacharam, Rangareddy, Keesara, Hyderabad, Medchal Malkajgiri, Telangana, 500076

9704156476 satyam.goddumarri@vimta.com

Scope List