BIS - LIMS (Laboratory Information Management System)

CIPET:CSTS Amritsar

P.O. Rayon & Silk Mills, Amritsar, Amritsar, Punjab, 143105

7890926806 amritsar@cipet.gov.in

Scope List

Reset

16 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

Black Film Type-I, II, III and IV

25725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	2025	Film Density Charges: 700 + Black Compound Charges : 700+625 =Rs.2025/-
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	1850	Film CBC Charges : 925 + Black Compound Charges : 925 =Rs.1850/-
5.1.6(Ash content - IS 2508: 2024)	-	1200	-
5.1.6(carbon black dispersion - IS 2530: 1963)	-	1400	Film CBD Charges : 700 + Black Compound Charges : 700 =Rs.1400/-
5.1.1(Appearance)	-	500	-
5.1.2(Film Form)	-	0	-
5.1.3(Odour)	-	0	-
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	2200	Film MFI Charges : 1100 + Black Compound Charges : 1100 =Rs.2200/-
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	1000	Nominal Thickness Charges : 500 + Thickness Tolerance Charges : 500 =Rs.1000/-
5.2.1.2(Nominal Width)	-	1000	Nominal Width Charges : 500 + Thickness Width Charges : 500 =Rs.1000/-
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	Tensile Strength Charges : 1300 Specimen Charges : 500 = 1800/-
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1300	-
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	-
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	5500	Tensile Strength Charges : 1300 Ageing Charges : 4200 = 5500/-
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1300	-
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	850	-
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	1600	Tear resistance Charges : 1100 Specimen Charges : 500 = 1600/-
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	1100	-
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	1100	-

06 Jan, 2027

-
-

IS 16098 Part 2 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 2 Pipes and Fittings with Non-Smooth External Surface, Type B

Upto 1200mm (Type B)

105600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table -1 Cl. No. 5.1, i)(Base Density)	-	2700	Material Identification-2000 Base Density-700
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	1100	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	2200	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	4800	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	11000	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	500	-
6.3.2(Length of Pipe)	-	500	-
6.3.3(Out Side Diameter)	-	0	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	0	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	0	-
6.3.5.2(Wall Thickness(e4 min))	-	500	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	0	-
7.1(Appearance)	-	800	Appearance = 500 Joint (VA) = 300
7.1.1(Color of Finished Pipes)	-	500	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	1100	-
8.1.1 Table-10 (i)(Ring Stiffness)	-	1100	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	1100	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	1100	-
8.1.1 Table-10 (iv)(Creep ratio)	-	26300	Creep ratio- Rs. 1100 + 25200 (Specimen)
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	5500	-
9 Table 12 (ii)(Water tightness)	-	1000	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	43800	Resistance to combined temperature cycling and external loading= 3900 Resistance to Hydrostatic pressure= 4800

06 Jan, 2027

-
-

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

Woven Sacks For Packaging 10Kg, 15Kg, 20Kg, 25Kg 30Kg

23130 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	-
4.2(Tapes – Linear Density )	-	700	-
4.3(Sacks)	-	500	-
4.3.1(Bottom Seam)	-	500	-
4.3.1(The number of stitches/dm)	-	0	-
4.3.2(Mouth)	-	500	-
4.4 and Table 1 i(Capacity)	-	500	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	250	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
5.1 and Table 1 v(Mass of sack )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	Average breaking strength and elongation at break Lengthwise-Rs.1100 Widthwise-Rs.1100 UV Resistance Exposure (192hrs)-Rs.10180
5.2 and Table 1 x(Ash content )	-	1200	-

06 Jan, 2027

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

Upto1500 Ltrs and Above 1500ltrs

22425 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	1850	Carbon black content -Tank:925 Carbon black content -Raw Material: 925
4.2.3(Carbon Dispersion Test)	-	1400	Carbon black content -Tank:700 Carbon black content -Raw Material: 700
5(Types and Features )	-	0	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	Net & Gross Capacity-Rs.500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	Overall Diameter-Rs. 500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	Overall Height-Rs. 500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	Internal dia of man – hole-Rs. 500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	Wall thickness upon effective height-Rs. 500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	Wall thickness above effective height-Rs. 500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	500	-
5.3(Types and Features )	-	500	Provision of Flat area-Rs. 500
5.6(Types and Features )	-	0	-
6.1(Finish)	-	500	-
7.1.1(Resistance to Deformation)	-	700	-
7.2(Resistance to Impact)	-	1000	-
7.3(Test for Top Load Resistance)	-	900	-
7.4(Tensile Strength)	-	1800	Rs. 1300 + 500 (Specimen)
7.5(Flexural Modulus)	-	1600	Rs. 1100 + 500 (Specimen)
7.6(overall Migration)	-	2200	Rs. 1700 + 500 (Specimen)
9.2.1(Man-Hole and Hand-Hole Lids)	-	1050	-
9.2(Man-Hole and Hand-Hole Lids)	-	1000	Lid Lock Up=500 Lid Clearance=500
9.1(Lid Thickness)	-	500	-
5.4(Wall Thickness above effective height)	-	500	-
5.2 Table 2 (7)(Minimum Wall Thickness)	-	500	-
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500	-
4.2.1(Density)	-	1400	Density -Tank:700 Density -Raw Material: 700
4.2.2(MFI)	-	2200	Tank:1100 Raw Material: 1100
4.1(MATERIALS)	-	2100	Tank:1050 Raw Material: 1050
5.4(Wall Thickness)	-	500	-

06 Jan, 2027

-
-

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

20mm To 200mm

122250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4( Designation)	-	5100	1.Material Identification- Rs.1050 2.Density- Rs.700+625(Specimen) 3.Melt Flow Rate (MFR)- Rs. 1100 4.Carbon Black Content (Optional)-Rs. 925 5.Carbon Black Dispersion (Optional)-Rs. 700 6.Overall Migration-Rs. 1700
Cl 7(Dimensions Of Pipes)	-	500	-
Cl 8(Visual Appearance)	-	500	-
Cl 9.1(Hydraulic Characteristics)	-	18400	i.) Acceptance Test (1 h. /20˚C)- Rs.1000 ii.) Acceptance Test (22 h. /95˚C)- Rs.1600 iii) Type test ( 165 h./95˚C)- Rs. 4800 iv) Type test ( 1000 h./ 95˚C)- Rs. 11000
Cl 9.2(Fusion Compatibility)	-	4800	-
Cl 9.3(Reversion Test )	-	1200	Reversion Test- Rs. 700+500 (Specimen)
Cl 9.4 & Annex B(Impact Strength)	-	1600	Impact Strength- Rs. 1100+500 (Specimen)
Cl 9.5(Density)	-	700	-
Cl 9.6(Melt Flow Rate)	-	1100	-
Cl 9.7(Carbon Black Content & Dispersion)	-	1625	1.Carbon Black Content- Rs. 925 2.Carbon Black Dispersion- Rs. 700
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	83825	Thermal stability by Hydrostatic Pressure Testing (8760 h. /110˚C)- Rs. 1700 + 82125(Specimen/Conditioning Charges)
Cl 9.9(Opacity)	-	700	-
5(Colour)	-	500	-

06 Jan, 2027

-
-

IS 15532 (2004)

Plastics crates for fruits and vegetables - Specification

Plastics Crates for Fruits and Vegetables

13200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4(Mass)	-	500	-
3.5(Appearance and Surface Finish)	-	500	-
3.6(Dimensional Stability)	-	700	-
3.7(Confluence Line Strength)	-	1100	-
3.8.1(Compressive Strength (Resistance to Applied Load))	-	1100	-
3.8.2(Resistance to Drop)	-	1100	-
3.9(Resistance to Environmental Stress Cracking)	-	1200	-
3.10.1(Suspension Test)	-	1100	-
3.10.2(Free-Fall Test)	-	1100	-
3.2(Material)	-	2000	-
3.3(Shape, Dimensions and Design)	-	500	-
3.3(Shape, Dimensions and Design)	-	0	-
3.2(Material)	-	1800	Density = 700 + Melt Flow Index=1100
3.1(Crates)	-	500	-
3.7(Confluence line Strength)	-	1100	-

06 Jan, 2027

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

High Density Polyethylene Pipes for Potable Water Suppl

49825 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	6000	5500+500 (Specimen Charges)
8.9 table-6(Elongation at Break)	-	1800	at Yield Strength = 1300+500 (Specimen Charges)
8.8(Tensile Strength for Butt-fusion)	-	1800	1300+500 (Specimen Charges)
8.7(Density)	-	700	0
8.5 (Oxidation Induction Time)	-	2200	0
8.4( Melt Flow Rate)	-	1100	0
8.2(Longitudinal Reversion Test)	-	1200	700+500 (Specimen Charges)
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	0
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	Test Duration (min.) 48 hrs = 1600 Test Duration (min.) 100 hrs= 4000 Test Duration (min.) 165 hrs= 4800 Test Duration (min.) 1000 hrs=11000
7.4.1.2(Ovality)	-	0	0
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	750	0
7.2(Length)	-	500	0
6.2.1(6.1.1 Identification Stripes)	-	500	0
6.2(Colour)	-	500	0
8.6(Overall migration)	-	2200	1700+500 (Specimen Charges)
CL 7.4(Wall Thickness (Take 8 reading & Minimum and Maximum reported))	-	500	-
Cl 8.3(Carbon Black Content)	-	925	-
Cl 8.3(Carbon Black Dispersion)	-	700	-
Clause 7.1(Visual Apperance)	-	500	-
5.2(Volatile matter Content)	-	700	Raw Material
5.2(Polyethylene Resin)	-	5450	Base Density : 700 Melt Flow Rate : 1100 Carbon Black Content: 925 Carbon Black Dispersion :700 Volatile Content :700 Water Content :700

06 Jan, 2027

-
-

IS 14500 (1998)

Linearlow - Densitypolyethylene (Lldpe)Films - Specification

Linear Low Density Polyethylene (LLDPE) Films

12225 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1.1(Appearance)	-	500	-
6.1.2(Film form)	-	0	Included in Clause 6.1.1
6.1.3(Odour)	-	0	Included in Clause 6.1.1
6.1.4(Density)	-	3625	Density : 700 Material Identification:2000 CBC:925
6.2.1(Nominal Thickness and Nominal Width)	-	1000	Thickness: 500 Width: 500
6.2.2(Tolerance on Thickness)	-	500	-
6.2.3(Tolerance on Width)	-	500	-
6.3(Yield Tolerance)	-	600	-
6.4.1(Impact Strength (Falling Dart))	-	850	-
6.4.2(Haze)	-	700	-
6.4.3(Slip)	-	850	-
6.4.4(Tensile strength at break)	-	3100	Tensile MD:1300 Tensile TD: 1300, Specimen Charges :500
6.4.5(Elongation at break)	-	0	Included in Clause 6.4.4
7(Packaging and Marking)	-	0	Included in Clause 6.1.1

06 Jan, 2027

-
-

IS 13664 (1993)

Poly - Pallets for bag storage godowns - Specification

Poly - Pallets for bag storage godowns (Type-A)

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 (Table-1)(Nominal Assembly Dimensions)	-	500	-
5.3(Dimensions and Cross Sectional Details of Members)	-	1000	-
7(Material Identification)	-	2000	-
8.1(Type)	-	500	-
8.2(Stability)	-	0	-
8.3(Assembly)	-	0	-
8.5(End Plugs)	-	0	-
8.6(Weight)	-	500	-
9.1.1 Table-2(Axial Crushing load)	-	1600	1100+500 (Specimen)
9.1.1 Table-2(Cross Sectional crushing load)	-	1100	-
9.1.1 Table-2(Ultimate bending load)	-	1600	1100+500 (Specimen)
9.1.2 Table-3(Shear Strength)	-	1600	1100+500 (Specimen)
9.1.2 Table-3(Ultimate tensile strength & Elongation)	-	1800	1300+500 (Specimen)
9.1.2 Table-3(Impact Strength)	-	1600	1100+500 (Specimen)
9.1.2 Table-3(Thermal Stability)	-	1300	700+600 (Specimen)
9.1.2 Table-3(Water absorpation)	-	1100	600+500 (Specimen)
9.1.2 Table-3(Chemical Resistance)	-	1600	1100+500 (Specimen)
9.1.2 Table-3(Bent Strength at yield)	-	1600	1100+500 (Specimen)
9.1.2 Table-3(Compressive strength at 10% deformation)	-	1600	1100+500 (Specimen)

06 Jan, 2027

-
-

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

Irrigation Equipment - Quick Coupled Polyethylene Pipe

66500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.3, Table 1,(i)(Bass density)	-	700	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	1100	-
4.1.3, Table 1,(iii)(Thermal stability)	-	2200	-
4.1.3, Table 1,(iv)(Volatile matter)	-	700	-
4.1.3, Table 1,(v)(Water content)	-	700	-
4.1.3, Table 1,(vi)(Minimum tensile strength at yield)	-	1800	1300 (Testing) + 500 (Specimen Preparation)
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	0	-
4.1.4(Carbon Black Content)	-	925	-
4.1.4(Carbon Black Dispersion)	-	700	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	500	-
5(Dimensions of pipe - i) Outside diameter)	-	500	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	500	-
6.1(Quick Coupled Pipes and Fittings)	-	700	-
6.2.1(Base Density x 2)	-	1400	-
6.2.1(Melt Flow Index x 2)	-	2200	-
6.2.1(Thermal Stability (OIT) x 2)	-	4400	-
6.1(Volatile Matter)	-	1400	-
6.2.1(Water content x 2)	-	1400	-
6.2.1(Carbon Black Content x 2)	-	1850	-
6.2.1(Carbon Black Dispersion x 2)	-	1400	-
6.2.1(Wall thickness of male & female coupler)	-	1000	-
6.2.4(Workmanship and appearance (Visual))	-	500	-
6.2.5(Holding attachment for coupler parts)	-	850	-
6.2.6(Material Identification (Chemical Analysis))	-	1050	-
6.2.6(Color)	-	500	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	500	-
6.2.6(Ageing Charges for rubber ring)	-	4200	-
7.1.1(Visual appearance of pipes)	-	500	-
7.1.2(Hydraulic Performance Characteristic)	-	4800	-
Cl.7.1.2(Hydraulic Characteristic)	-	1600	-
7.1.3(Reversion Test)	-	1200	700 (Testing) + 500 (Specimen Preparation)
7.1.4(Tensile Test)	-	1800	1300 (Testing) + 500 (Specimen Preparation)
Cl.7.1.4(Elongation)	-	0	-
7.1.5(Fusion Compatibility Test)	-	4800	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	1600	-
7.1.6(Base Density)	-	700	-
7.1.7(Melt flow rate)	-	1100	-
7.2.1(Leakage Test)	-	850	-
7.2.2(Hydraulic Proof Test)	-	850	-
7.2.3(Weldability Test)	-	4800	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	1600	-
8(Supply of pipe (Visual))	-	500	-
7.1.6(Carbon black Content)	-	925	-
6.1(Thermal Stability (OIT))	-	2200	-
6.1(Water content)	-	700	-
6.1(Tensile strength at Yield & Elongation at break)	-	1800	-
Cl.6.2.6(Rubber Ring Hardness)	-	500	-

06 Jan, 2027

-
-

IS 2508 (2024)

Polyethylene Films and Sheets â Specification (Fourth Revision)

Polyethylene Films and Sheets and Specification

25725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.4 Sl No. (i) of Table 1, Table 2, Table 3 & Table 4.(Density - IS 13360 : Part 3 : Sec 10 : 2021)	-	700	-
5.1.6(Black Film- Carbon black - IS 2508:2024)	-	925	-
5.1.6(Ash content - IS 2508: 2024)	-	1200	-
5.1.6(carbon black dispersion - IS 2530: 1963)	-	700	-
5.1.1(Appearance)	-	500	-
5.1.2(Film Form)	-	0	Test Charges Included in Appearance Test
5.1.3(Odour)	-	0	Test Charges Included in Appearance Test
5.1.5(Melt Flow Index- IS 13360 : Part 4 : Sec 1 : subsec 1 or IS 13360 : Part 4 : Sec 1 : subsec 2)	-	1100	-
5.2.1.1/ Table-1,2,3 &4(Nominal Thickness, Annex C,)	-	500	-
5.2.1.2(Nominal Width)	-	500	-
6, Type 1 (LDPE/LLDPE) /Table-1("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
6/Table-1("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
6/Table-1("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	Test Charges Included in Tensile Test
6/Table-1("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	Test Charges Included in Tensile Test
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	6000	1300 Test Charges + 500 Specimen + 4200 Ageing Test for 7 days
6/Table-1("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
6/Table-1(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	850	-
6/Table-1(Tear resistance -Machine direction, IS 13360 (Part 5/Sec 23))	-	1600	1100 Test Charges + 500 Specimen
6/Table-1(Tear resistance-Transverse direction, IS 13360 (Part 5/Sec 23))	-	1600	1100 Test Charges + 500 Specimen
" 7, Type 2 (HDPE/PE) /Table-2"("Tensile strength at break-Machine direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
" 7/Table-2"("Tensile strength at break-Transverse direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
" 7/Table-2"("Elongation % at break, -Machine direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	Test Charges Included in Tensile Test
" 7/Table-2"("Elongation % at break, -Transverse direction,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/ Sec 3)")	-	0	Test Charges Included in Tensile Test
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days-Machine Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	6000	1300 Test Charges + 500 Specimen + 4200 Ageing Test for 7 days
" 7/Table-2"("Ageing test at (70 ± 1) ºC for 7 days- Transverse Direction, IS 7016 (Part 8) followed by IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
" 7/Table-2"(Dart impact strength,Method B of IS 13360 (Part 5/Sec 6))	-	850	-
8, Type 3 (LDPE/LLDPE, PE) /Table-3("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
8/Table-3("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
8/Table-3("Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	Test Charges Included in Tensile Test
8/Table-3("Average Tensile Break Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	0	Test Charges Included in Tensile Test
8/Table-3(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1600	1100 Test Charges + 500 Specimen
8/Table-3(Average Puncture resistance, IS 2508: 2024 Annex-E)	-	1100	-
9, Type 4 (HDPE/PE) /Table-4("Average Yield strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
9/Table-4("Average Yield strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
9/Table-4("Average Tensile Break strength- Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
9/Table-4("Average Tensile Break strength- Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
9/Table-4("Average Tensile yield Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
9/Table-4("Average Tensile yield Elongation %-Transverse Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3)")	-	1800	1300 Test Charges + 500 Specimen
9/Table-4(Average Tensile Break Elongation %-Machine Direction, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 3))	-	1800	1300 Test Charges + 500 Specimen
9/Table-4(Average Tensile Break Elongation -Transverse Direction, IS 13360 (Part 5/Sec 1) and S 13360 (Part 5/Sec 3))	-	1800	1300 Test Charges + 500 Specimen
9/Table-4(Average Tear resistance, IS 2508: 2024 Annex-D)	-	1600	1100 Test Charges + 500 Specimen
Cl-4.2.3.1.4 (b)(Toluene Extract)	-	1100	-
Cl-4.2.3.1.4 (c)(Volatile Matter, Max)	-	700	-
Cl-4.2.3.1.4 (d)(Carbon Black Particle Size)	-	925	-
Cl-4.2.3.1.4 (e)(Tint Strength)	-	1800	1300 Test Charges + 500 Specimen
Cl-4.2.3.1.4 (a)(Density)	-	700	-

06 Jan, 2027

-
-

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

17725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	1050	-
Cl-4.2(Carbon content of finished PE lateral pipe)	-	925	-
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	500	-
Cl-6.0(Visual Appearance)	-	500	-
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	1000	-
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	3000	-
Cl-7.2(Reversion Test)	-	1200	Test Charges Rs.700 + Specimen Charges Rs. 500
Cl-7.3(Tensile Test)	-	1800	Test Charges Rs.1300 + Specimen Charges Rs. 500
Cl-7.3.1(Test Piece)	-	0	-
Cl-7.3.2(Procedure)	-	0	-
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	1200	-
Cl-8.0(Supply of pipes)	-	500	-
Cl-9.0(Coiling)	-	0	-
Cl-10.0(Sampling and criteria for conformity)	-	0	-
3(Class of Pipe)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	-
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	-
6(Visual Appearance)	-	500	-
7.1 & Table 2(Hydraulic Characteristics)	-	1000	-
7.1 & Table 2(Hydraulic Characteristics)	-	3000	-
7.2(Reversion Test)	-	1200	Test Charges Rs.700 + Specimen Charges Rs. 500
7.3(Tensile Strength)	-	1800	Test Charges Rs.1300 + Specimen Charges Rs. 500
7.3(Elongation at Break)	-	0	-
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	-
4.2(a)(Carbon Black Content-IS 2530)	-	925	-
4.2(b)(Carbon Black Dispersion-IS 2530)	-	700	-
Cl-11(Marking)	-	0	-

06 Jan, 2027

-
Included w.e.f 24.03.2026

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials

28380 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Mass of Bale)	-	500	-
5.2 Table 1(Dimensions)	-	500	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Dimensions)	-	0	-
5.2 Table 1(Ends per dm)	-	500	-
5.2 Table 1(Picks per dm)	-	500	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	500	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	1600	1100 Testing Charges + 500 Specimen Charges
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	1100	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1600	1100 Testing Charges + 500 Specimen Charges
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	-
5.2 Table 1(Drop impact strength)	-	1100	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	1200	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	1200	-
4.6(Capacity)	-	500	-
4.3.1(Bottom Seam)	-	500	-
4.3(Sacks)	-	500	-
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	2700	2200 Testing Charges + 500 Specimen Charges
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	10180	-
4.2(Linear Density)	-	700	-
4.2(Width of tape)	-	500	-
Cl-4.4(Lamination Mass)	-	500	-
Cl-4.5(Liner- Thickness)	-	500	-
Cl-4.2 (Amendment No-2)(un-laminated fabric mass)	-	500	-
Cl-4.5(Liner- Width)	-	500	-
Cl-4.5(Liner- Visible defects)	-	500	-
4.6(Capacity)	-	-	-
4.3.1(Bottom Seam)	-	-	-
4.3(Sacks)	-	-	-
4.2,5.1,5.2,5.3,5.4(Breaking strenght after U.V. Exposure (Warp/Weft))	-	-	-
4.2,5.1,5.2,5.3,5.4,(UV Resistance (192 hrs)(100 x 65+92x40))	-	-	-
4.2(Linear Density)	-	-	-
4.2(Width of tape)	-	-	-
Cl-4.4(Lamination Mass)	-	-	-
Cl-4.5(Liner- Thickness)	-	-	-
Cl-4.2 (Amendment No-2)(un-laminated fabric mass)	-	-	-
Cl-4.5(Liner- Width)	-	-	-
Cl-4.5(Liner- Visible defects)	-	-	-

06 Jan, 2027

-
included w.e.f 27.01.2026

IS 14611 (2024)

Multilayered Cross Laminated Sheets/Tarpaulins/Covers/Agricultural Films â Specification (Second Revision)

Multilayered Cross Laminated Sheets/Tarpaulins/Covers/Agricultural Films Specification (Second Revision)

41955 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6.1(Workmanship)	-	500	-
Cl-6.2, 6.3 & 6.8, Table-1 (i)(Mass per unit area, g/m²)	-	500	-
Cl-6.2, 6.3 & 6.8, Table-1 (ii)("Tensile strength1), Min,kg/cm²- (a) Longitudinal direction")	-	1300	-
Cl-6.2, 6.3 & 6.8, Table-1 (ii)("Tensile strength1), Min,kg/cm² (b) Transverse direction")	-	1300	-
Cl-6.2, 6.3 & 6.8, Table-1 (iii)("After ageing at 70 ºC ± 1 ºC for 168 h, Max, kg/cm2 a)Longitudinaldirection")	-	1300	-
Cl-6.2, 6.3 & 6.8, Table-1 (iii)("After ageing at 70 ºC ± 1 ºC for 168 h, Max, kg/cm2 b) Transverse direction")	-	1300	-
Cl-6.2, 6.3 & 6.8, Table-1 (iv)("Elongation at break, Min, percent a)Longitudinaldirection")	-	0	included in Tensile Strength
Cl-6.2, 6.3 & 6.8, Table-1 (iv)("Elongation at break, Min, percent b) Transverse direction")	-	0	included in Tensile Strength
Cl-6.2, 6.3 & 6.8, Table-1 (v)("Tear strength, Min, g: a)Longitudinaldirection")	-	1300	-
Cl-6.2, 6.3 & 6.8, Table-1 (v)("Tear strength, Min, g: b)Transverse direction")	-	1300	-
Cl-6.2, 6.3 & 6.8, Table-1 (vi)(Dart impact strength, Min, g)	-	850	-
Cl-6.2, 6.3 & 6.8, Table-1 (vii)(Average tensile strengthand elongation at breakafter exposing to UVradiation and weathering,Min, (kgf))	-	12780	Tensile Strength (LD) 1300+Tensile Strength (TD) 1300+ UV Exposure 10180
Cl-6.4(Water Proofness Test)	-	1000	-
Cl-6.5(Strength of Joints/Seams)	-	1100	-
Cl-6.6(Flex Test)	-	7200	Flex Test (Before Ageing)50000 Cycles = 1500 Flex Test (After Ageing)50000 Cycles = 1500 Ageing = 4200
Cl-6.7(Ease of In-Situ Repair)	-	1300	-
Cl-7(Fixing of Eyelets (for tarpaulins only))	-	500	-
Cl-9(Packing and Marking)	-	500	-
Cl-6.3(Accelerated Ageing Test)	-	4200	-
Cl-5(Construction of sheets/tarpaulins/covers/agricultural films)	-	2425	Construction of Tarpaulins Carbon black content=925 Panel=500 Ends & sides dimension=500 Panel Length & Width=500

06 Jan, 2027

-
Included w.e.f 18.11.2025

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent – Specification

54875 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1325	700+(Specimen) 625
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2200	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	700	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	700	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	925	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	700	-
6.2(Colour- IS 14333-2022)	-	500	-
7.1(Visual Appearance- IS 14333-2022)	-	500	-
7.2(Length- IS 14333-2022)	-	500	-
7.3(Coiling- IS 14333-2022)	-	0	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	500	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	4000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	4800	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	11000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	1200	700+(Specimen) 500
8.3(Carbon black content- IS 2530-1963)	-	925	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	700	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1100	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2200	-
8.6(Density-IS 7328:2020)	-	700	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1800	1300+(Specimen) 500
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1800	1300+(Specimen) 500
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	Test Charges inculeded in Tensile Strength
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	6000	5500+(Specimen) 500
6(Pipe Description - IS 14333-2022)	-	0	Included in Visual
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	700	-
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	900	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	700	-
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	3000	-
5.2.1.1, T2(Compound ash content - Any Method)	-	1200	-
5.3(Density of Higher olefin - IS 7328:2020)	-	700	-
5.3(Olefin Constituents- 14333-2022)	-	0	NA
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	NA
5.3(Ash content- Any Method)	-	1200	-
5.3(Toluene extract - Any Method)	-	900	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	700	-
5.3(Carbon black particle size - Any Method)	-	3000	-
5.4(Antioxidant - Any Method)	-	0	NA
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	700	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2200	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	700	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	700	625 is specimen Charges extra
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	925	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	700	-
6.2(Colour- IS 14333-2022)	-	500	Visual
7.1(Visual Appearance- IS 14333-2022)	-	500	-
7.2(Length- IS 14333-2022)	-	500	-
7.3(Coiling- IS 14333-2022)	-	500	Visual
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	0	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	Repeting Parameter
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	Repeting Parameter
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	Repeting Parameter
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	Repeting Parameter
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	0	-
8.3(Carbon black content- IS 2530-1963)	-	0	Repeting Parameter
8.3(Carbon black content Dispersion- IS 2530-1963)	-	0	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	Repeting Parameter
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	0	-
8.6(Density-IS 7328:2020)	-	0	Repeting Parameter
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	0	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	Repeting Parameter
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	0	Repeting Parameter
6(Pipe Description - IS 14333-2022)	-	0	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	0	Repeting Parameter
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	0	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	0	Repeting Parameter
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	0	-
5.2.1.1, T2(Compound ash content - Any Method)	-	0	Repeting Parameter
5.3(Density of Higher olefin - IS 7328:2020)	-	0	Repeting Parameter
5.3(Olefin Constituents- 14333-2022)	-	0	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3(Ash content- Any Method)	-	0	Repeting Parameter
5.3(Toluene extract - Any Method)	-	0	Repeting Parameter
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	Repeting Parameter
5.3(Carbon black particle size - Any Method)	-	0.04	Repeting Parameter
5.4(Antioxidant - Any Method)	-	0	Repeting Parameter
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	0	Repeting Parameter
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	0.01	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	0	Repeting Parameter
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	0	Repeting Parameter
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	0	Repeting Parameter
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	0	Repeting Parameter
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	0	-
6.2(Colour- IS 14333-2022)	-	0	Repeting Parameter
7.1(Visual Appearance- IS 14333-2022)	-	0.02	Repeting Parameter
7.2(Length- IS 14333-2022)	-	0	-
7.3(Coiling- IS 14333-2022)	-	0	Repeting Parameter
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	0	Repeting Parameter
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	Repeting Parameter
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	Repeting Parameter
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	Repeting Parameter
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	0	Repeting Parameter
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	0	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	0	Repeting Parameter
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	0	Repeting Parameter
8.3(Carbon black content- IS 2530-1963)	-	0.02	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	0.03	Repeting Parameter
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	0	Repeting Parameter
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	0	-
8.6(Density-IS 7328:2020)	-	0	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	0	Repeting Parameter
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	0	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	Repeting Parameter
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	0	Repeting Parameter
6(Pipe Description - IS 14333-2022)	-	0	Repeting Parameter
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	0.03	Repeting Parameter
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	0	Repeting Parameter
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	0	Repeting Parameter
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	0	Repeting Parameter
5.2.1.1, T2(Compound ash content - Any Method)	-	0	-
5.3(Density of Higher olefin - IS 7328:2020)	-	0	Repeting Parameter
5.3(Olefin Constituents- 14333-2022)	-	0	Repeting Parameter
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3(Ash content- Any Method)	-	0	-
5.3(Toluene extract - Any Method)	-	0	Repeting Parameter
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	-
5.3(Carbon black particle size - Any Method)	-	0	Repeting Parameter
5.4(Antioxidant - Any Method)	-	0	Repeting Parameter

06 Jan, 2027

-
included w.e.f 17.11.2025

IS 12650 (2018)

Textiles – Jute bags for packing 50 kg foodgrains – Specification (third revision)

Textiles – Jute bags for packing 50 kg foodgrains – Spe

10326 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4-4.1(MANUFACTURE)	-	500	-
5-5.1-Table 1-Sr. no.i i)(SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Ends/dm Type A 46 + 2 /Type B 76 + 4 / -3)	-	500	-
5-5.1-Table 1-Sr. no.iii)(SPECIFIC REQUIREMENTS-Cl. 8.4.2 of IS 9113 Picks/dm Type A 50 (2 x 25) / Type B 28 + 2)	-	500	-
5-5.1-Table 1-Sr. no.iv)(SPECIFIC REQUIREMENTS-Cl. 8.5.2 of IS 9113 Corrected Mass/bag, g ( See Note 2) For both Type A & Type B 665 + 8.0 / -6.0 percent)	-	500	-
5-5.1-Table 1-Sr. no. i)(SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 a) Out side Length , cm 94 (For both type A & Type B) Tolerance + 4 / -0 cm)	-	500	-
5-5.1-Table 1-Sr. no. i)(SPECIFIC REQUIREMENTS-Dimensions (see Note 1) Cl. 8.3.2 of IS 9113 b) Outside width, cm 57 (For both type A & Type B) Tolerance + 4 / -0 cm)	-	500	-
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): a ) Warpway- 1570 (160) for both type A & Type B)	-	1300	-
5-5.1-Table 1-Sr. No.v)(SPECIFIC REQUIREMENTS-Cl. 8.6.2 of IS 9113 Average breaking strength of sacking (ravelled-strip method, 10 cm × 20 cm), Min, N (kgf): b ) Weftway- 1420 (145) for both type A & Type B)	-	1300	-
5-5.1-Table 1-Sr. No.vi)(SPECIFIC REQUIREMENTS-Cl. 8.7 of IS 9113 Average side seam strength (5 cm ×20 cm raveled strip), Min, N (kgf): 490 (50) for both type A & Type B)	-	1300	-
5-5.1-Table 1-Sr. No.vii)(SPECIFIC REQUIREMENTS-Cl. 8.2 of IS 9113 Moisture regain, percent, Max (see Note 3) 22 for both type A & Type B)	-	700	-
5-5.1-Table 1-Sr. No.viii)(SPECIFIC REQUIREMENTS-Cl. 8.8 of IS 9113 Oil content on dry de-oiled material, Max 3 for both type A & Type B)	-	1100	-
4-4.3(Manufacture-Safety Stitch )	-	500	-
4-4.4(Manufacture-Hemming at the Mouth )	-	500	-
5-5.2-Table 2-Sr. No.v)(SPECIFIC REQUIREMENTS- Visual Number of joined bags per bundle of 25 bags )	-	500	-
4-4.2(Manufacture-The number of stitches per decimeter shall be 10 ±1.)	-	500	-

06 Jan, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET:CSTS Amritsar

P.O. Rayon & Silk Mills, Amritsar, Amritsar, Punjab, 143105

7890926806 amritsar@cipet.gov.in

Scope List