BIS - LIMS (Laboratory Information Management System)

Atmy Analytical Labs Pvt. Ltd.

I-30,DLF Industrial Area, Phase-1, Faridabad, Faridabad, Haryana, 121003

9910808996 info@atmylabs.com

Scope List

Reset

288 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 3735 (1996)

Canvas Shoes, Rubber Sole

all

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	18000	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	18000	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	18000	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	18000	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	18000	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	18000	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	18000	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	18000	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	18000	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	18000	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	18000	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	18000	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	18000	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	0	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	18000	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	18000	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	18000	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	18000	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	18000	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	0	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	18000	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	0	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	0	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	0	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	18000	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	18000	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	0	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	0	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	0	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	0	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	0	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	0	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	0	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	0	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	0	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	0	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	0	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	0	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	0	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	0	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	0	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	0	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	0	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	0	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	0	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	0	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	0	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	0	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	0	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	18000	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	0	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	0	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	0	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	0	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	0	-
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	0	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	0	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	0	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	0	-
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	0	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	0	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	0	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	0	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	0	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	0	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	0	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	0	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	0	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	0	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	0	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	0	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	18000	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	0	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	18000	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	18000	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	0	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	18000	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	0	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	0	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	18000	-
4.8(Adhesion )	-	0	-
4.7(Consolidation test )	-	0	-
4.6(Mass )	-	0	-
4.5(Finish )	-	18000	-
4.4(Contruction )	-	18000	-
4.3(Leg Height )	-	18000	-
4.2(Design )	-	18000	-
4.1.6.2(Thickness of components )	-	18000	-
4.1.6.2(Ageing)	-	0	-
4.1.6.2(Elongation at break after ageing )	-	18000	-
4.1.6.2(Tensile after ageing )	-	18000	-
4.1.6(Compression set )	-	18000	-
4.1.6(Elongation at break )	-	18000	-
4.1.6(Tensile strength)	-	18000	-
4.1.6(Hardness (after accelerated ))	-	18000	-
4.1.6(Flexing resistance test)	-	0	-
4.1.6(Hardness )	-	0	-
4.1.6(Relative density)	-	18000	-
4.1.5(Sulpher dyes content )	-	18000	-
4.1.5(Breaking Load )	-	18000	-
4.1.5(Length )	-	18000	-
4.1.4(Thickness)	-	18000	-
4.1.4(Size )	-	18000	-
4.1.3(Color fastness to perspiration)	-	18000	-
4.1.3(Colorfastness to washing)	-	18000	-
4.1.3(Colorfastness to light )	-	18000	-
4.1.3(Single thread breaking load)	-	18000	-
4.1.3(Construction )	-	0	-
4.1.2(Colorfastness to light )	-	0	-
4.1.2(Colorfastness to washing)	-	0	-
4.1.2(Breaking Strength )	-	0	-
4.1.2(Width )	-	0	-
4.1.1.2(Colorfastness to washing)	-	0	-
4.1.1.1(Colorfastness to light )	-	0	-
4.1.1 (Drill) (End & Picks/dm)	-	18000	-
4.1.1 (Drill) (Colorfastness to light )	-	18000	-
4.1.1 (canvas )(End & Picks/dm)	-	18000	-
4.1.1 (canvas )(Breaking Load )	-	18000	-
5, 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking)	-	18000	-
" CL. 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking ")	-	0	-

Complete

25 Feb, 2027

-
Amendment No. 5 included w.e.f. 25.03.2025

IS 2266 (2024)

STEEL WIRE ROPES FOR GENERAL ENGINEERING PURPOSE - SPECIFICATION (Sixth Revision)

19900 View breakup
-

Clause No.	Exclusion	Remark
Cl-5(Minimum breaking force)	-	-
Cl-6(Wire rope)	-	-
Cl-7(Construction)	-	-
Cl-8.1(Fibre Core)	-	-
Cl-8.2(Steel Core)	-	-
Cl-9(Joints)	-	-
Cl-10(Galvanizing)	-	-
Cl-12(Marking)	-	-
Cl-4(Rope size and Tolerance)	-	-
Cl-5(Minimum breaking force)	-	-
Cl-6(Wire rope)	-	-
Cl-7(Construction)	-	-
Cl-8.1(Fibre Core)	-	-
Cl-8.2(Steel Core)	-	-
Cl-9(Joints)	-	-
Cl-10(Galvanizing)	-	-
Cl-12(Marking)	-	-
Cl-4(Rope size and Tolerance)	-	-
Cl-5(Minimum breaking force)	-	-
Cl-6(Wire rope)	-	-
Cl-7(Construction)	-	-
Cl-8.1(Fibre Core)	-	-
Cl-8.2(Steel Core)	-	-
Cl-9(Joints)	-	-
Cl-10(Galvanizing)	-	-
Cl-12(Marking)	-	-
Cl-4(Rope size and Tolerance)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 09.04.2025

IS 4521 (2024)

Wire Ropes Used in Oil Wells and Oil Well Drilling and Other Applications of Petroleum and Natural Gas Industries - Specification (Third Revision)

19900 View breakup
-

Clause No.	Exclusion	Remark
Cl-4(Size, Construction, Core and Grades)	-	-
Cl-5(Minimum breaking force)	-	-
Cl-6.1(Wire for guy strands)	-	-
Cl-6.2(Core)	-	-
Cl-6.3(Joints)	-	-
Cl-6.4(Mass)	-	-
Cl-6.5(Lay of the Rope)	-	-
Cl-6.6(Length of Lay)	-	-
Cl-7(Galvanizing)	-	-
Cl-8(Lubrication)	-	-
Cl-9(Rope grades)	-	-
Cl-10(wire tensile strength grade)	-	-
Cl-11(Tolerance in rope diameter)	-	-
Cl-12(Marking)	-	-
Cl-4(Size, Construction, Core and Grades)	-	-
Cl-5(Minimum breaking force)	-	-
Cl-6.1(Wire for guy strands)	-	-
Cl-6.2(Core)	-	-
Cl-6.3(Joints)	-	-
Cl-6.4(Mass)	-	-
Cl-6.5(Lay of the Rope)	-	-
Cl-6.6(Length of Lay)	-	-
Cl-7(Galvanizing)	-	-
Cl-8(Lubrication)	-	-
Cl-9(Rope grades)	-	-
Cl-10(wire tensile strength grade)	-	-
Cl-11(Tolerance in rope diameter)	-	-
Cl-12(Marking)	-	-
Cl-4(Size, Construction, Core and Grades)	-	-
Cl-5(Minimum breaking force)	-	-
Cl-6.1(Wire for guy strands)	-	-
Cl-6.2(Core)	-	-
Cl-6.3(Joints)	-	-
Cl-6.4(Mass)	-	-
Cl-6.5(Lay of the Rope)	-	-
Cl-6.6(Length of Lay)	-	-
Cl-7(Galvanizing)	-	-
Cl-8(Lubrication)	-	-
Cl-9(Rope grades)	-	-
Cl-10(wire tensile strength grade)	-	-
Cl-11(Tolerance in rope diameter)	-	-
Cl-12(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 09.04.2025

IS 18427 (2024)

Three piece round open top metal cans for foods and beverages -- Specification

34900 View breakup
-

Clause No.	Exclusion	Remark
Cl-5.1.1(C)	-	-
Cl-5.1.1(Si)	-	-
Cl-5.1.1(Mn)	-	-
Cl-5.1.1(P)	-	-
Cl-5.1.1(S)	-	-
Cl-5.1.2, Table-1("Tinplate Nominal Thickness- Flattened Body")	-	-
Cl-5.1.2, Table-1(Built-up Can Body- Beaded)	-	-
Cl-5.1.2, Table-1(Built-up Can Body- Un-beaded)	-	-
Cl-5.1.2, Table-1(Tinplate Nominal Thickness- NEO Ends)	-	-
Cl-5.1.2, Table-2(Tinplate Nominal Thickness- Un-beaded Body)	-	-
Cl-5.1.2, Table-2(Tinplate Nominal Thickness- Beaded Body)	-	-
Cl-5.1.2, Table-2(Tinplate Nominal Thickness- NEO End)	-	-
Cl-5.1.2, Table-2(Tinplate Nominal Thickness- Ring)	-	-
Cl-5.1.2, Table-2(Tinplate Nominal Thickness- Lid)	-	-
Cl-5.1.3, Table-3 (i)(Mango pulp – Body and ends)	-	-
Cl-5.1.3, Table-3 (ii)(Pineapple – Body and ends)	-	-
Cl-5.1.3, Table-3 (iii)(All other thermally processed cans – Body and ends)	-	-
Cl-5.1.3, Table-3 (iv)(Non-thermally processed can – Body and ends)	-	-
Cl-5.1.3, Table-3 (v)(Ring and lid)	-	-
Cl-5.1.3, Table-3 (vi)(POE ring)	-	-
Cl-5.1.4(Surface Finish)	-	-
Cl-5.1.5(Tin Grain Size)	-	-
Cl-5.1.6(Iron Solution Value)	-	-
Cl-5.1.7(Surface Oil)	-	-
Cl-5.1.8(Passivation Treatment)	-	-
Cl-5.1.9(Edge Camber and Out-of-Squareness)	-	-
Cl-5.1.10(Mechanical Properties)	-	-
Cl-5.2(Lacquers and Decorative Coatings)	-	-
Cl-5.3(Inks)	-	-
Cl-5.4(Lining Compound/Can End Sealants)	-	-
Cl-5.5(Side Stripe Systems)	-	-
Cl-5.6(Easy Open End)	-	-
Cl-5.7(Aluminium Tagger)	-	-
Cl-5.8(Peel Off Ends (POE))	-	-
Cl-5.9(Surface Lubrications and Rust Prevention Oils)	-	-
Cl-6.1, Table-5(Internal Diameter)	-	-
Cl-6.1, Table-5(Necked-In Side Trade Size)	-	-
Cl-6.1, Table-5(Necked-In Side Nominal Diameter)	-	-
Cl-6.2(Capacities)	-	-
Cl-7(Manufacture)	-	-
Cl-8.1, Table-9 (i)(Thermally processed food cans)	-	-
Cl-8.1, Table-9 (ii)(Nonthermally processed food cans)	-	-
Cl-8.2(Vacuum Test)	-	-
Cl-8.3(Migration Test)	-	-
Cl-8.4(Specific Migration Limit (SML)	-	-
Cl-10.1(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 16.04.2025

IS 14543 (2016)

Packaged drinking water (Other Than Packaged Natural Mineral Water) - Specification (Second Revision)

28000 View breakup
-

Clause No.	Exclusion	Remark
5.3 Table-4 ii (Beta emitters)	-	-
5.3 Table-4 i (Alpha emitters)	-	-
5.4 ii)(Total pesticied residue)	-	-
5.4 i)(Dieldrin)	-	-
5.4 i)(Aldrin)	-	-
5.4 i)(Malaoxon)	-	-
5.4 i)(Malathion)	-	-
5.4 i)(Methyl Paraoxon)	-	-
5.4 i)(Methyl Parathion)	-	-
5.4 i)(Atrazine)	-	-
5.4 i)(Alachlor)	-	-
5.4 i)(Isoproturon)	-	-
5.4 i)(Butachlor)	-	-
5.4 i)(2,4-D)	-	-
5.4 i)(phorate sulphone)	-	-
5.4 i)(Phorate sulphoxide)	-	-
5.4 i)(Phorate)	-	-
5.4 i)(Chlorpyrifos)	-	-
5.4 i)(Ethion)	-	-
5.4 i)(Monocrotophos)	-	-
5.4 i)(Endosulfan Sulphate)	-	-
5.4 i)(beta-Endosulfan)	-	-
5.4 i)(alpha-Endosulfan)	-	-
5.4 i)(Delta-HCH)	-	-
5.4 i)(beta-HCH)	-	-
5.4 i)(alpha-HCH)	-	-
5.4 i)(Gamma-HCH (Lindane))	-	-
5.4 i)(p,p DDD)	-	-
5.4 i)(o,p DDD)	-	-
5.4 i)(p,p DDE)	-	-
5.4 i)(o,p DDE)	-	-
5.4 i)(p,p DDT)	-	-
5.4 i)(o,p DDT)	-	-
5.3 Table-3 ix (Polynuclear aromatic hydrocarbons)	-	-
5.3 Table-3 viii (Polychlorinated biphenyle (PCB))	-	-
5.3 Table-3 vii(Nickel (as Ni))	-	-
5.3 Table-3 vi(Chromium (as Cr))	-	-
5.3 Table-3 v(Lead (as Pb))	-	-
5.3 Table-3 iv (Cyanide (as CN))	-	-
5.3 Table-3 iii(Arsenic (as As))	-	-
5.3 Table-3 ii(Cadmium (as Cd))	-	-
5.3 Table-3 i(Mercury (as Hg))	-	-
5.3 Table-2 xxv(Bromates (as BrO3),)	-	-
5.3 Table-2 xxiv(Borates (as B))	-	-
5.3 Table-2 xxiii(Antimony (as Sb))	-	-
5.3 Table-2 xxii(Sulphide (as H2S))	-	-
5.3 Table-2 xxi (Anionic surface active agents (as MBAS))	-	-
5.3 Table-2 xx(Mineral oil)	-	-
5.3 Table-2 xix (Phenolic compounds (as C6H5OH))	-	-
5.3 Table-2 xviii(Residual free chlorine)	-	-
5.3 Table-2 xvii(Sodium (as Na))	-	-
5.3 Table-2 xvi(Magnesium (as Mg))	-	-
5.3 Table-2 xv(Calcium (as Ca),)	-	-
5.3 Table-2 xiv(Alkaliniity (as HCO3))	-	-
5.3 Table-2 xiii(Sulphate (as SO4),)	-	-
5.3 Table-2 xii(Selenium (as Se),)	-	-
5.3 Table-2 xi(Chloride (as Cl))	-	-
5.3 Table-2 x(Aluminium (as Al))	-	-
5.3 Table-2 ix(Silver (as Ag))	-	-
5.3 Table-2 viii(Zinc (as Zn))	-	-
5.3 Table-2vii(Fluoride (as F))	-	-
5.3 Table-2 vi(Nitrite (as NO2))	-	-
5.3 Table-2 v(Nitrate (as NO3))	-	-
5.3 Table-2 iv(Manganese (as Mn))	-	-
5.3 Table-2 iii(Iron (as Fe),)	-	-
5.3 Table-2 ii(Copper (as Cu))	-	-
5.3 Table-2 i(Barium (as Ba))	-	-
5.3 Table-1vi(pH)	-	-
5.3 Table-1 v(Total dissolved solids)	-	-
5.3 Table-1 iv(Turbidity)	-	-
5.3 Table-1 iii(Taste)	-	-
5.3 Table-1 ii(Odour)	-	-
5.3 Table-1 i(Colour)	-	-
5.3(Description)	-	-
5.2.9(Vibrio parahaemolyticus)	-	-
5.2.9(Vibrio cholera)	-	-
5.2.8(Shigella)	-	-
5.2.8(Salmonella)	-	-
5.2.7(Yeast and Mould)	-	-
5.2.6(Aerobic Microbial Count at 37°C)	-	-
5.2.6(Aerobic Microbial Count at 20-22°C)	-	-
5.2.5(Pseudomonas Aeruginosa)	-	-
5.2.4(Sulphite Reducing Anaerobes)	-	-
5.2.3(Staphylococcus Aureus)	-	-
5.2.3(Faecal Streptococci)	-	-
5.2.2(Coliform)	-	-
5.2.1(Escherichia coli (or thermotolerant bacteria))	-	-
6(Overall Migration)	-	-
6(Colour Migration)	-	-
10.0(Water potability test-taste)	-	-
10.0(Water potability test - odour)	-	-
4.6.5(Colour Migration (cap))	-	-
4.6.6(Overall Migration-caps)	-	-
4.6.5(Overall Migration-bottles)	-	-
4.6.4(Drop test)	-	-
4.6.3( Air pressure leakage test)	-	-
4.6.3( Vibration leakage test )	-	-
4.6.3( Clousure leakage test)	-	-
4.6.2(Transparency)	-	-
4.5(Thickness- Bottom)	-	-
4.5(Thickness- Middle)	-	-
4.5(Thickness- Top)	-	-
4.4(Brirnful Capacity )	-	-
4.3(Workn-ranship, Finish & Appearance)	-	-
4.2.1(Peelability)	-	-
4.2(Design, Shape & Dimension)	-	-
5.4(i)(δ – HCH / USEPA 525.2-1995 (Rev 2) USEPA 508-1989 (Rev 3))	-	-
5.4(ii)(Total Pesticide Residues / USEPA 525.2-1995 (Rev 2) USEPA 8141A – 1994 (Rev I) USEPA 507-1989 (Rev 2) USEPA 1657A – 2000 USEPA 508-1989 (Rev 3) USEPA 515.1 – 1995 USEPA 532 – 2000 (Rev 1)	-	-
Table 3, x)(Uranium)	-	-
Table 3, x) (radioactive)(Uranium)	-	-
5.3 Table-3 x(Uranium)	-	-
Cl.5.4, i)(o,p DDE)	-	-
Cl.5.4, i)("oxygen analogue of Malathion (Malaoxon)")	-	-

Complete

25 Feb, 2027

-
-

IS 15844 : Part 3 (2024)

Sports Footwear Part 3 Professional Sports Footwear

64900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Size and Fittings)	-	1000	-
Cl-5(Design)	-	1000	-
Cl-6(Size and Fittings)	-	1000	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	6000	Upper to midsole/outsole-Rs 2000/- Upper to composite sole- Rs 2000/- Outsole to midsole-Rs 2000/-
Cl.7.1.2(Energy Absorption at Seat Region)	-	2000	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	0	-
Cl.7.1.2(Energy Absorption at Seat Region)	-	0	-
Cl.7.1.3(Complete Shoe Flexing)	-	4000	-
Cl.7.1.4(Washability)	-	5500	-
Cl.7.1.5(Slip Resistance)	-	5500	-
Cl.7.1.6(Heel Drop)	-	1000	-
Cl.7.2 Table-2 S.No- (i)("Flexing resistance, Min a) Dry condition b) Wet condition")	-	2000	Dry condition- Rs 1000/- Wet condition- Rs 1000/-
Cl.7.2 Table-2 S.No- (ii)(Tear strength (average force), N, Min)	-	1000	-
Cl.7.2 Table-2 S.No- (iii)("Colour fastness rubbing a-Dry b-Wet")	-	3000	Dry- Rs 1500/- Wet- Rs 1500/-
Cl.7.2 Table-2 S.No- (iv)("a) Water vapour permeability b) Water vapour coefficient")	-	2000	water vapour permeability- Rs 1000/- Water vapour coefficient- Rs 1000/-
Cl.7.2 Table-2 S.No- (v)(Stitch tear strength N/mm, Min)	-	1000	-
Cl.7.2 Table-2 S.No- (vi)(Colour fastness to light grey scale rate)	-	5000	-
Cl.7.2 Table-2 S.No- (vii)(Tensile strength)	-	1000	-
Cl.7.2 Table-2 S.No- (viii)(Elongation at break, percent)	-	1000	-
Cl.7.2 Table-2 S.No- (ix)("Abrasion test a) Dry b) Wet")	-	3000	Dry- Rs 1500/- Wet- Rs 1500/-
Cl.7.2 Table-3 S.No- (i)(Breaking strength, N/mm, Min)	-	1000	-
Cl.7.2 Table-3 S.No- (ii)(Elongation at break, percent, Min)	-	1000	-
Cl.7.2 Table-3 S.No- (iii)(Tear strength, N, Min)	-	1000	-
Cl.7.2 Table-3 S.No- (iv)(Strength at needle perforation)	-	1000	-
Cl.7.2 Table-3 S.No- (v)("Flexing resistance a-Dry condition, b) Wet condition")	-	3000	Dry- Rs 1500/- Wet- Rs 1500/-
Cl.7.2 Table-3 S.No- (vi)("a) Water vapour permeability b) Water vapour coefficient")	-	2000	water vapour permeability- Rs 1000/- Water vapour coefficient- Rs 1000/-
Cl.7.2 Table-3 S.No- (vii)(Hydrolysis resistance)	-	1500	-
Cl.7.2 Table-3 S.No- (viii)(Colour fastness to light grey scale rate)	-	5000	-
Cl.7.2 Table-3 S.No- (ix)(Bursting strength)	-	1000	-
Cl.7.3 Table-4 S.No- (i)(Tear strength, N, Min)	-	1000	-
Cl.7.3 Table-4 S.No- (ii)("Abrasion resistance, a) Dry b) Wet ")	-	3000	Dry- Rs 1500/- Wet- Rs 1500/-
Cl.7.3 Table-4 S.No- (iii)(Colour fastness to rubbing, grey scale rate with 10 rubs on dry or wet, Min)	-	1000	-
Cl.7.3 Table-4 S.No- (iv)(Colour fastness to perspiration (contact method) grey scale rate, Min)	-	1000	-
Cl.7.3 Table-4 S.No- (v)("a-Water vapour permeability b-Water vapour coefficient")	-	2000	water vapour permeability- Rs 1000/- Water vapour coefficient- Rs 1000/-
Cl.7.4 Table-5 S.No- (i)(Flexing index, Min)	-	1000	-
Cl.7.4 Table-5 S.No- (ii)(Abrasion resistance)	-	1500	-
Cl.7.4 Table-5 S.No- (iii)("a) Water absorption b) Water desorption")	-	3000	Water absorption- Rs 1500/- Water desorption- Rs 1500/-
Cl.7.5 Table-6 S.No- (i)("Abrasion resistance a) Dry condition b) Wet condition")	-	3000	Dry- Rs 1500/- Wet- Rs 1500/-
Cl.7.5 Table-6 S.No- (ii)("a) Water absorption b) Water desorption")	-	3000	Water absorption- Rs 1500/- Water desorption- Rs 1500/-
Cl.7.5 Table-6 S.No- (iii)(Heat resistance shrinkage linear, percent, Max)	-	1000	-
Cl.7.6 Table-7 S.No- (i)(Abrasion resistance)	-	1000	-
Cl.7.6 Table-7 S.No- (ii)("Flexing resistance a) Bennewart Method b) Ross flexing method")	-	1500	-
Cl.7.6 Table-7 S.No- (iii)(Hydrolysis resistance)	-	1500	-
Cl.7.6 Table-7 S.No- (iv)(Tear strength, N/mm, Min)	-	1000	Complete Testing Charges
Cl.7.6 Table-7 S.No- (v)(Tensile strength)	-	1000	-
Cl.7.6 Table-7 S.No- (vi)(Elongation at break percent, Min)	-	1000	-
Cl.7.6 Table-7 S.No- (vii)(Compression set percent, Max)	-	1000	-
Cl.7.7 Table-8 S.No- (i)("Compression set, percent, Max a) For EVA b) For all other material")	-	1000	-
Cl.7.7 Table-8 S.No- (ii)(Split tear strength)	-	1000	-
Cl.7.7 Table-8 S.No- (iii)(Heat shrinkage, percent, Ma)	-	1000	-
Cl.7.7 Table-8 S.No- (iii)(Elongation at break, percent, Min)	-	1000	-
Cl.7.7 Table-8 S.No- (iv)(Elongation at break, percent, Min)	-	1000	-
Cl.7.8 Table-9 S.No- (i)(First dry collapsing load, hardness, N, Min)	-	0	Cl 7.8 Table 9, S.no.1 to S.no. 4- Total Rs 2500/-
Cl.7.8 Table-9 S.No- (ii)(Resilience, percent, Min)	-	0	-
Cl.7.8 Table-9 S.No- (iii)(Moisture resistance, percent, Min)	-	0	-
Cl.7.8 Table-9 S.No- (iv)("a) Initial dry area shape retention, percent, Min b) Area shape retention after 10th collapse, dry, percent, Min ")	-	0	-
Cl.7.8 Table-9 S.No- (v)(Peel strength, N/nm, Min)	-	1000	-
Cl.7.9 Table-10 S.No- (i)("Peel strength, N/mm, Min a) Initial b) After 5 000 wear cycles")	-	3000	Peel strength, initial- Rs 1500/- Peel strength, After 5000 cycle- Rs 1500/-
Cl.7.9 Table-10 S.No- (ii)("Shear strength, kPa, Min a) Initial b) After 5 000 wear cycles")	-	3000	shear strength, initial- Rs 1500/- shear strength, After 5000 cycle- Rs 1500/-
Cl.7.10 Table-11 S.No- (i)(Limit of useful extension, percent, Min)	-	1000	-
Cl.7.10 Table-11 S.No- (ii)(Needle strength, N/mm, Min)	-	1000	-
Cl.7.11 Table-12 S.No- (i)(Breaking strength of lace)	-	1000	-
Cl.7.11 Table-12 S.No- (ii)(Lace tag strength)	-	1000	-
Cl.7.11 Table-12 S.No- (iii)(Lace to lace abrasion)	-	1000	-
Cl.7.11 Table-12 S.No- (iv)(Colour fastness to water (for lace) (Contact method))	-	1000	-
Cl.7.11 Table-12 S.No- (v)(Strength of buckle/ski hook/D-ring,)	-	1000	-
Cl.7.11 Table-12 S.No- (vi)("Corrosion resistance (applicable for all including decorative metal part) ")	-	1000	-
Cl.7.11 Table-13 S.No- (i)(Corrosion resistance (applicable for metallic spikes))	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	0	Chemical requirement- Rs 35000/-, Lead content- Rs 2500/-
Cl-7.12.1, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(x)(pH)	-	0	-
Cl-7.12.1, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	0	-
C-7.12.1, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	0	-
Cl-7.12.2(PVC is present in sports shoe)	-	0	-
Cl- 8.1(Marking)	-	500	-

Complete

25 Feb, 2027

-
-

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

all

64900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(SAMPLING AND CONDITIONING)	-	1000	-
5(DESIGN)	-	1000	-
6(SIZE AND FITTINGS)	-	1000	-
7.1.1(Whole Footwear)	-	1000	-
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	2000	-
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	2000	-
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	2000	-
7.1.5(Energy Absorption at Seat Region)	-	2000	-
7.1.6(Complete Shoe Flexing)	-	4000	-
7.1.7(Washability)	-	5500	-
7.1.8(Slip Resistance)	-	5500	-
7.1.9(Heel Drop)	-	1000	-
7.2 , Table No. 2 , i)(Flexing resistance)	-	1500	-
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	1000	-
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	1500	-
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	1000	-
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	1000	-
7.2 , Table No. 2 , v)(Stitch tear strength (double hole))	-	1000	-
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	5000	-
7.2 , Table No. 2 , vii)(Tensile strength)	-	1000	-
7.2 , Table No. 2 , viii)(Elongation at break,)	-	1000	-
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	1000	-
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	1500	-
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	1000	-
7.2 , Table No. 3 , ii)(Elongation at break)	-	1000	-
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	1000	-
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	1000	-
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	1500	-
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	1000	-
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	1000	-
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	1500	-
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	5000	-
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	1000	-
7.3 , Table No. 4 , i)(Tear strength,)	-	1000	-
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	1500	-
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	1000	-
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	1000	-
7.3 , Table No. 4 , v) , a)(Water vapour permeability,)	-	1000	-
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	1000	-
7.4 , Table No. 5 , i)(Thickness)	-	1000	-
7.4 , Table No. 5 , ii)(Flexing index)	-	1000	-
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	1500	-
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	1500	-
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	1500	-
7.5 , Table No. 6 , i)(Thickness)	-	1000	-
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	1500	-
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	1500	-
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	1500	-
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	1000	-
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	1000	-
7.6 , Table No. 7 , ii)(Flexing resistance)	-	1500	-
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	1500	-
7.6 , Table No. 7 , iv)(Tear strength)	-	1000	-
7.6 , Table No. 7 , v)(Tensile strength)	-	1000	-
7.6 , Table No. 7 , vi)(Elongation at break)	-	1000	-
7.6 , Table No. 7 , vii)(Compression set)	-	1000	-
7.7 , Table No. 8 , i)(Compression set)	-	1000	-
7.7 , Table No. 8 , ii)(Split tear strength,)	-	1000	-
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	1000	-
7.7 , Table No. 8 , iv)(Elongation at break,)	-	1000	-
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	0	Table no. 9 -S.No. 1 to S.No. 4 testing charge- 2500
7.8 , Table No. 9 , ii)(Resilience)	-	0	-
7.8 , Table No. 9 , iii)(Moisture resistance)	-	0	-
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	0	-
7.8 , Table No. 9 , v)(Peel strength)	-	1000	-
7.9 , Table No. 10 , i)(Peel strength)	-	1500	-
7.9 , Table No. 10 , ii)(Shear strength)	-	1500	-
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	1000	-
7.10 , Table No. 11 , ii)(Needle strength,)	-	1000	-
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	1000	-
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	1000	-
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	1000	-
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	1000	-
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	1000	-
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	1000	-
7.12("Chemical Requirement on Complete Product for All Types of Sports Shoe")	-	35000	Complete testing charge of chemical requirement- 35000 Lead content- 2500
7.12, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
7.12, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
7.12, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	0	-
7.12, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	0	-
7.12, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
7.12, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	0	-
7.12, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
7.12, Table no. 1 of IS 17011,(x)(pH)	-	0	-
7.12, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	0	-
7.12, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	0	-

Complete

25 Feb, 2027

-
-

IS 17397 : Part 1 (2022)

PLASTICS THERMOPLASTIC POLYURETHANES FOR MOULDING AND EXTRUSION PART 1 DESIGNATION SYSTEM AND SPECIFICATIONS

34900 View breakup
-

Clause No.	Exclusion	Remark
4.1(General)	-	-
4.2.1(Data Block 1)	-	-
4.2.2(Data Block 2)	-	-
4.2.3(Data Block 3)	-	-
4.2.4(Data Block 4)	-	-
4.2.5(Data Block 5)	-	-
4.2.5.1(Hardness)	-	-
4.2.5.2(Tensile Modulus of Elasticity)	-	-
4.2.6(Data Block 6)	-	-
6.1(Hardness)	-	-
6.2(Tensile Modulus of Elasticity)	-	-
6.3.1.1(Pigments and Colourants)	-	-
6.3.1.2(Overall Migration)	-	-
7(Packing and Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 24.02.2025

IS 17682 (2021)

ALUMINIUM COMPOSITE PANEL SPECIFICATION

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 5.1(Polymer Granules)	-	5000	Rs. 42000/- for all test excluding Table 3 & 4 Clause 5.1 Melt flow Index - Rs.2500/- Ash content - Rs.2500/-
Clause 5.2(Aluminium Alloy Sheets)	-	1000	Clause 5.2 - Rs.500/- Clause 5.3 - Rs.500/-
Clause 5.4(Surface Coating)	-	500	-
Clause 6(DIMENSIONS AND TOLERANCE)	-	3000	Clause 6.1 - Length - Rs.750/- Width - Rs.750/- Clause 6.2 Thickness - Rs.1500/- Table-1 Edge Straightness - Rs.1500/- Table-1 Squarenss - Rs.1500/-
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	2000	-
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	1500	-
"Clause 7.1 Table 2(iii)"(Yield strength)	-	1500	-
"Clause 7.1 Table 2(iv)"(Elongation)	-	1500	-
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	2500	-
"Clause 7.1 Table 3(i)"(Coating type)	-	2000	Coating type and Coating Thickness - Rs.2000/-
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	0	-
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	7000	Dry - Rs.2000/- Wet - Rs.2000/- Boiling water - Rs.3000/-
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	2000	-
"Clause 7.1 Table 3(v)"(Gloss)	-	2000	-
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	0	Amendment no.1,Sept.2024 Sl. no. (V) a).1 Humidity Test - Rs.200,000/- a).2 Corrosion Test-Rs.200,000/- b) Weathering test PVDF/FEVE(2 Coat) - Rs.400,000/- PVDF/FEVE(3 Coat)- Rs.400,000/- SDP(2/3 Coat)-Rs.300,000/- Polyester(1 Coat)-Rs.100,000/-
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	7500	Amendment no.1,Sept.2024 a) 1500/- b) 1500/- c) 1500/- d) 1500/- e) 1500/-
"Clause 7.1 Table 4(i)"(Limiting oxygen index (LOI), Min)	-	15000	-
"Clause 7.1 Table 4(ii)"(Smoke density rating, percent, Max)	-	15000	-
"Clause 7.1 Table 4(iii)"(Ignitability)	-	15000	-
"Clause 7.1 Table 4(iv)"(Flame spread)	-	115000	-
"Clause 7.1 Table 4(v)"(Non-combustibility (see Note))	-	35000	-
"Clause 7.1 Table 4(vi)"(Oxygen bomb calorimeter)	-	15000	-
"Clause 7.2 Table 5(i)"(Sound transmission class (STC), dB, Min)	-	0	-
"Clause 7.2 Table 5(ii)"(Sound absorption coefficient, percent, Min)	-	0	-
"Clause 7.2 Table 5(iii)"(Coefficient of linear thermal expansion, °C–1 , Max)	-	0	-
"Clause 7.2 Table 5(iv)"(Thermal Conductivity (W/m2 K), Max)	-	0	-
Clause 5.1(Polymer Granules)	-	0	-
Clause 5.2(Aluminium Alloy Sheets)	-	0	-
Clause 5.4(Surface Coating)	-	0	-
Clause 6(DIMENSIONS AND TOLERANCE)	-	0	-
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	0	-
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	0	-
"Clause 7.1 Table 2(iii)"(Yield strength)	-	0	-
"Clause 7.1 Table 2(iv)"(Elongation)	-	0	-
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	0	-
"Clause 7.1 Table 3(i)"(Coating type)	-	0	-
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	0	-
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	0	-
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	0	-
"Clause 7.1 Table 3(v)"(Gloss)	-	0	-
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	0	-
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	0	-
"Clause 7.1 Table 4(i)"(Limiting oxygen index (LOI), Min)	-	0	-
"Clause 7.1 Table 4(ii)"(Smoke density rating, percent, Max)	-	0	-
"Clause 7.1 Table 4(iii)"(Ignitability)	-	0	-
"Clause 7.1 Table 4(iv)"(Flame spread)	-	0	-
"Clause 7.1 Table 4(v)"(Non-combustibility (see Note))	-	0	-
"Clause 7.1 Table 4(vi)"(Oxygen bomb calorimeter)	-	0	-
"Clause 7.2 Table 5(i)"(Sound transmission class (STC), dB, Min)	-	0	-
"Clause 7.2 Table 5(ii)"(Sound absorption coefficient, percent, Min)	-	0	-
"Clause 7.2 Table 5(iii)"(Coefficient of linear thermal expansion, °C–1 , Max)	-	0	-
"Clause 7.2 Table 5(iv)"(Thermal Conductivity (W/m2 K), Max)	-	0	-
Clause 5.1(Polymer Granules)	-	0	-
Clause 5.2(Aluminium Alloy Sheets)	-	0	-
Clause 5.4(Surface Coating)	-	0	-
Clause 6(DIMENSIONS AND TOLERANCE)	-	0	-
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	0	-
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	0	-
"Clause 7.1 Table 2(iii)"(Yield strength)	-	0	-
"Clause 7.1 Table 2(iv)"(Elongation)	-	0	-
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	0	-
"Clause 7.1 Table 3(i)"(Coating type)	-	0	-
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	0	-
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	0	-
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	0	-
"Clause 7.1 Table 3(v)"(Gloss)	-	0	-
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	0	-
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	0	-
"Clause 7.1 Table 4(i)"(Limiting oxygen index (LOI), Min)	-	0	-
"Clause 7.1 Table 4(ii)"(Smoke density rating, percent, Max)	-	0	-
"Clause 7.1 Table 4(iii)"(Ignitability)	-	0	-
"Clause 7.1 Table 4(iv)"(Flame spread)	-	0	-
"Clause 7.1 Table 4(v)"(Non-combustibility (see Note))	-	0	-
"Clause 7.1 Table 4(vi)"(Oxygen bomb calorimeter)	-	0	-
"Clause 7.2 Table 5(i)"(Sound transmission class (STC), dB, Min)	-	0	-
"Clause 7.2 Table 5(ii)"(Sound absorption coefficient, percent, Min)	-	0	-
"Clause 7.2 Table 5(iii)"(Coefficient of linear thermal expansion, °C–1 , Max)	-	0	-
"Clause 7.2 Table 5(iv)"(Thermal Conductivity (W/m2 K), Max)	-	0	-

Complete

25 Feb, 2027

-
-

IS 15298 : part 4 (2024)

Personal Protective Equipment Part 4 Occupational Footwear (ISO 20347 : 2021, MOD) (Third Revision)

53900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	53900	-
Cl 5.2.2(" Height of upper ")	-	53900	-
Cl 5.2.3(Heel area)	-	53900	-
Cl 5.3.1.1(Construction of whole footwear)	-	53900	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	53900	-
Cl 5.3.2(Leak proofness)	-	53900	-
Cl 5.3.3(Specific ergonomic features)	-	53900	-
Cl 5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	53900	-
Cl 5.3.5, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (x)(pH)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	53900	-
Cl 5.3.6(Seam strength)	-	53900	-
Cl 5.3.7(Lead Content ( National Annex A))	-	53900	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.2(Thickness)	-	53900	-
Cl 5.4.3(Tear strength)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties- Tensile strength)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties- Breaking Force)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties-Modulus at 100 % elongation)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.5(Flexing resistance)	-	53900	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	53900	-
Cl 5.4.7(Resistance to hydrolysis)	-	53900	-
Cl 5.5.2(Lining- Tear strength)	-	53900	-
Cl 5.5.3(Lining- Abrasion resistance)	-	53900	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	53900	-
Cl 5.6.2(Tear strength of tongue)	-	53900	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	53900	-
Cl 5.7.2(Water permeability of insock)	-	53900	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	53900	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	53900	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	53900	-
Cl 5.8.2.1(Thickness of Outsole)	-	53900	-
Cl 5.8.2.2(Cleated area)	-	53900	-
Cl 5.8.2.3(Cleat height)	-	53900	-
Cl 5.8.3(Outsole- Tear strength)	-	53900	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	53900	-
Cl 5.8.5(Outsole-Flexing resistance)	-	53900	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	53900	-
Cl 5.8.7(Interlayer bond strength)	-	53900	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	53900	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	53900	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	53900	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	53900	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	53900	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	53900	-
Cl 6.2.1.4.2.1(ISO 20344:2021, 5.11.2)	-	53900	-
Cl 6.2.1.4.2.2(ISO 20344:2021, 5.6.2.1)	-	53900	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	53900	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	53900	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	53900	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	53900	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	53900	-
Cl 6.2.4(Energy absorption of seat region)	-	53900	-
Cl 6.2.5(Water resistance)	-	53900	-
Cl 6.2.6(Ankle protection)	-	53900	-
Cl 6.2.7.1(Cut resistance footwear- design)	-	53900	-
Cl 6.2.7.2(Dimensions and construction of protective area of Cut resistance footwear)	-	53900	-
Cl 6.2.7.3(Resistance to cutting)	-	53900	-
Cl 6.2.8(Scuff cap)	-	53900	-
Cl 6.2.9("Slip resistance on ceramic tile floor with glycerine ")	-	53900	-
Cl 6.3(Upper — Water penetration and absorption)	-	53900	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	53900	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	53900	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	53900	-
Cl 6.4.3.2(Design of Ladder grip)	-	53900	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	53900	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	53900	-
Cl 7("Marking ")	-	53900	-
Cl 5.2(Design)	-	53900	-
Cl 5.2.2(" Height of upper ")	-	53900	-
Cl 5.2.3(Heel area)	-	53900	-
Cl 5.3.1.1(Construction of whole footwear)	-	53900	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	53900	-
Cl 5.3.2(Leak proofness)	-	53900	-
Cl 5.3.3(Specific ergonomic features)	-	53900	-
Cl 5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	53900	-
Cl 5.3.5, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (x)(pH)	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	53900	-
Cl 5.3.5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	53900	-
Cl 5.3.6(Seam strength)	-	53900	-
Cl 5.3.7(Lead Content ( National Annex A))	-	53900	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.2(Thickness)	-	53900	-
Cl 5.4.3(Tear strength)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties- Tensile strength)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties- Breaking Force)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties-Modulus at 100 % elongation)	-	53900	-
Cl 5.4.4, Table 9(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.5(Flexing resistance)	-	53900	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	53900	-
Cl 5.4.7(Resistance to hydrolysis)	-	53900	-
Cl 5.5.2(Lining- Tear strength)	-	53900	-
Cl 5.5.3(Lining- Abrasion resistance)	-	53900	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	53900	-
Cl 5.6.2(Tear strength of tongue)	-	53900	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	53900	-
Cl 5.7.2(Water permeability of insock)	-	53900	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	53900	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	53900	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	53900	-
Cl 5.8.2.1(Thickness of Outsole)	-	53900	-
Cl 5.8.2.2(Cleated area)	-	53900	-
Cl 5.8.2.3(Cleat height)	-	53900	-
Cl 5.8.3(Outsole- Tear strength)	-	53900	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	53900	-
Cl 5.8.5(Outsole-Flexing resistance)	-	53900	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	53900	-
Cl 5.8.7(Interlayer bond strength)	-	53900	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	53900	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	53900	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	53900	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	53900	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	53900	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	53900	-
Cl 6.2.1.4.2.1(ISO 20344:2021, 5.11.2)	-	53900	-
Cl 6.2.1.4.2.2(ISO 20344:2021, 5.6.2.1)	-	53900	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	53900	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	53900	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	53900	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	53900	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	53900	-
Cl 6.2.4(Energy absorption of seat region)	-	53900	-
Cl 6.2.5(Water resistance)	-	53900	-
Cl 6.2.6(Ankle protection)	-	53900	-
Cl 6.2.7.1(Cut resistance footwear- design)	-	53900	-
Cl 6.2.7.2(Dimensions and construction of protective area of Cut resistance footwear)	-	53900	-
Cl 6.2.7.3(Resistance to cutting)	-	53900	-
Cl 6.2.8(Scuff cap)	-	53900	-
Cl 6.2.9("Slip resistance on ceramic tile floor with glycerine ")	-	53900	-
Cl 6.3(Upper — Water penetration and absorption)	-	53900	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	53900	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	53900	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	53900	-
Cl 6.4.3.2(Design of Ladder grip)	-	53900	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	53900	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	53900	-
Cl 7("Marking ")	-	53900	-

Complete

25 Feb, 2027

-
Included w.e.f 13.03.2025

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

53900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	53900	-
Cl 5.2.2(" Height of upper ")	-	53900	-
Cl 5.2.3(Heel area)	-	53900	-
Cl 5.3.1.1(Construction of whole footwear)	-	53900	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	53900	-
Cl 5.3.2.1(Toe protection - general)	-	53900	-
Cl 5.3.2.2(Internal length)	-	53900	-
Cl 5.3.2.3(Width of toecap flange)	-	53900	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	53900	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	53900	-
Cl 5.3.2.6(Impact resistance)	-	53900	-
Cl 5.3.2.7(Compression resistance)	-	53900	-
Cl 5.3.3(Leak proofness)	-	53900	-
Cl 5.3.4("Specific ergonomic features ")	-	53900	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	53900	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	53900	-
Cl 5.3.7(Seam strength)	-	53900	-
Cl 5.3.8(Lead Content ( National Annex A))	-	53900	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.2(Thickness)	-	53900	-
Cl 5.4.3(Tear strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	53900	-
Cl 5.4.7(Resistance to hydrolysis)	-	53900	-
Cl 5.5.2(Lining- Tear strength)	-	53900	-
Cl 5.5.3(Lining- Abrasion resistance)	-	53900	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	53900	-
Cl 5.6.2(Tear strength of tongue)	-	53900	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	53900	-
Cl 5.7.2(Water permeability of insock)	-	53900	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	53900	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	53900	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	53900	-
Cl 5.8.2.1(Thickness of Outsole)	-	53900	-
Cl 5.8.2.2(Cleated area)	-	53900	-
Cl 5.8.2.3(Cleat height)	-	53900	-
Cl 5.8.3(Outsole- Tear strength)	-	53900	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	53900	-
Cl 5.8.5(Outsole-Flexing resistance)	-	53900	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	53900	-
Cl 5.8.7(Interlayer bond strength)	-	53900	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	53900	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	53900	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	53900	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	53900	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	53900	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	53900	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	53900	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	53900	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	53900	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	53900	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	53900	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	53900	-
Cl 6.2.4(Energy absorption of seat region)	-	53900	-
Cl 6.2.5(Water resistance)	-	53900	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	53900	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	53900	-
Cl 6.2.7(Ankle protection)	-	53900	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	53900	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	53900	-
Cl 6.2.8.3(Resistance to cutting)	-	53900	-
Cl 6.2.9(Scuff cap)	-	53900	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	53900	-
Cl 6.3(Upper — Water penetration and absorption)	-	53900	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	53900	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	53900	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	53900	-
Cl 6.4.3.2(Design of Ladder grip)	-	53900	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	53900	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	53900	-
Cl 7("Marking ")	-	53900	-
Cl 7("Marking ")	-	53900	-
Cl 5.2(Design)	-	53900	-
Cl 5.2.2(" Height of upper ")	-	53900	-
Cl 5.2.3(Heel area)	-	53900	-
Cl 5.3.1.1(Construction of whole footwear)	-	53900	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	53900	-
Cl 5.3.2.1(Toe protection - general)	-	53900	-
Cl 5.3.2.2(Internal length)	-	53900	-
Cl 5.3.2.3(Width of toecap flange)	-	53900	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	53900	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	53900	-
Cl 5.3.2.6(Impact resistance)	-	53900	-
Cl 5.3.2.7(Compression resistance)	-	53900	-
Cl 5.3.3(Leak proofness)	-	53900	-
Cl 5.3.4("Specific ergonomic features ")	-	53900	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	53900	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	53900	-
Cl 5.3.7(Seam strength)	-	53900	-
Cl 5.3.8(Lead Content ( National Annex A))	-	53900	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.2(Thickness)	-	53900	-
Cl 5.4.3(Tear strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	53900	-
Cl 5.4.7(Resistance to hydrolysis)	-	53900	-
Cl 5.5.2(Lining- Tear strength)	-	53900	-
Cl 5.5.3(Lining- Abrasion resistance)	-	53900	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	53900	-
Cl 5.6.2(Tear strength of tongue)	-	53900	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	53900	-
Cl 5.7.2(Water permeability of insock)	-	53900	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	53900	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	53900	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	53900	-
Cl 5.8.2.1(Thickness of Outsole)	-	53900	-
Cl 5.8.2.2(Cleated area)	-	53900	-
Cl 5.8.2.3(Cleat height)	-	53900	-
Cl 5.8.3(Outsole- Tear strength)	-	53900	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	53900	-
Cl 5.8.5(Outsole-Flexing resistance)	-	53900	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	53900	-
Cl 5.8.7(Interlayer bond strength)	-	53900	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	53900	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	53900	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	53900	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	53900	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	53900	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	53900	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	53900	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	53900	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	53900	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	53900	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	53900	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	53900	-
Cl 6.2.4(Energy absorption of seat region)	-	53900	-
Cl 6.2.5(Water resistance)	-	53900	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	53900	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	53900	-
Cl 6.2.7(Ankle protection)	-	53900	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	53900	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	53900	-
Cl 6.2.8.3(Resistance to cutting)	-	53900	-
Cl 6.2.9(Scuff cap)	-	53900	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	53900	-
Cl 6.3(Upper — Water penetration and absorption)	-	53900	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	53900	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	53900	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	53900	-
Cl 6.4.3.2(Design of Ladder grip)	-	53900	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	53900	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	53900	-
Cl 7("Marking ")	-	53900	-
Cl 7("Marking ")	-	53900	-

Complete

25 Feb, 2027

-
Included w.e.f 13.03.2025

IS 15298 : Part 2 (2024)

Personal Protective Equipment Part 2 Safety Footwear (ISO 20345 : 2021, MOD) (Third Revision)

53900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	53900	-
Cl 5.2.2, Table 4(" Height of upper ")	-	53900	-
Cl 5.2.3(Heel area)	-	53900	-
Cl 5.3.1.1(Construction of whole footwear)	-	53900	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	53900	-
Cl 5.3.2.1(Toe protection - general)	-	53900	-
Cl 5.3.2.2(Internal length)	-	53900	-
Cl 5.3.2.3(Width of toecap flange)	-	53900	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	53900	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	53900	-
Cl 5.3.2.6(Impact resistance)	-	53900	-
Cl 5.3.2.7(Compression resistance)	-	53900	-
Cl 5.3.3(Leak proofness)	-	53900	-
Cl 5.3.4("Specific ergonomic features ")	-	53900	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	53900	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	53900	-
Cl 5.3.7(Seam strength)	-	53900	-
Cl 5.3.8(Lead Content ( National Annex A))	-	53900	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.2(Thickness)	-	53900	-
Cl 5.4.3(Tear strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.5(Flexing resistance)	-	53900	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	53900	-
Cl 5.4.7(Resistance to hydrolysis)	-	53900	-
Cl 5.5.2(Lining- Tear strength)	-	53900	-
Cl 5.5.3(Lining- Abrasion resistance)	-	53900	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	53900	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	53900	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	53900	-
Cl 5.7.2(Water permeability of insock)	-	53900	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	53900	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	53900	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	53900	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	53900	-
Cl 5.8.2.2(Cleated area)	-	53900	-
Cl 5.8.2.3(Cleat height)	-	53900	-
Cl 5.8.3(Outsole- Tear strength)	-	53900	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	53900	-
Cl 5.8.5(Outsole-Flexing resistance)	-	53900	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	53900	-
Cl 5.8.7(Interlayer bond strength)	-	53900	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	53900	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	53900	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	53900	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	53900	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	53900	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	53900	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	53900	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	53900	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	53900	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	53900	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	53900	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	53900	-
Cl 6.2.4(Energy absorption of seat region)	-	53900	-
Cl 6.2.5(Water resistance)	-	53900	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	53900	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	53900	-
Cl 6.2.7(Ankle protection)	-	53900	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	53900	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	53900	-
Cl 6.2.8.3(Resistance to cutting)	-	53900	-
Cl 6.2.9(Scuff cap)	-	53900	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	53900	-
Cl 6.3(Upper — Water penetration and absorption)	-	53900	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	53900	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	53900	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	53900	-
Cl 6.4.3.2(Design of Ladder grip)	-	53900	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	53900	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	53900	-
Cl 7, Table 20("Marking ")	-	53900	-
Cl 5.2(Design)	-	53900	-
Cl 5.2.2, Table 4(" Height of upper ")	-	53900	-
Cl 5.2.3(Heel area)	-	53900	-
Cl 5.3.1.1(Construction of whole footwear)	-	53900	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	53900	-
Cl 5.3.2.1(Toe protection - general)	-	53900	-
Cl 5.3.2.2(Internal length)	-	53900	-
Cl 5.3.2.3(Width of toecap flange)	-	53900	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	53900	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	53900	-
Cl 5.3.2.6(Impact resistance)	-	53900	-
Cl 5.3.2.7(Compression resistance)	-	53900	-
Cl 5.3.3(Leak proofness)	-	53900	-
Cl 5.3.4("Specific ergonomic features ")	-	53900	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	53900	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	53900	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	53900	-
Cl 5.3.7(Seam strength)	-	53900	-
Cl 5.3.8(Lead Content ( National Annex A))	-	53900	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	53900	-
Cl 5.4.2(Thickness)	-	53900	-
Cl 5.4.3(Tear strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	53900	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	53900	-
Cl 5.4.5(Flexing resistance)	-	53900	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	53900	-
Cl 5.4.7(Resistance to hydrolysis)	-	53900	-
Cl 5.5.2(Lining- Tear strength)	-	53900	-
Cl 5.5.3(Lining- Abrasion resistance)	-	53900	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	53900	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	53900	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	53900	-
Cl 5.7.2(Water permeability of insock)	-	53900	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	53900	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	53900	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	53900	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	53900	-
Cl 5.8.2.2(Cleated area)	-	53900	-
Cl 5.8.2.3(Cleat height)	-	53900	-
Cl 5.8.3(Outsole- Tear strength)	-	53900	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	53900	-
Cl 5.8.5(Outsole-Flexing resistance)	-	53900	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	53900	-
Cl 5.8.7(Interlayer bond strength)	-	53900	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	53900	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	53900	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	53900	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	53900	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	53900	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	53900	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	53900	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	53900	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	53900	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	53900	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	53900	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	53900	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	53900	-
Cl 6.2.4(Energy absorption of seat region)	-	53900	-
Cl 6.2.5(Water resistance)	-	53900	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	53900	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	53900	-
Cl 6.2.7(Ankle protection)	-	53900	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	53900	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	53900	-
Cl 6.2.8.3(Resistance to cutting)	-	53900	-
Cl 6.2.9(Scuff cap)	-	53900	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	53900	-
Cl 6.3(Upper — Water penetration and absorption)	-	53900	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	53900	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	53900	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	53900	-
Cl 6.4.3.2(Design of Ladder grip)	-	53900	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	53900	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	53900	-
Cl 7, Table 20("Marking ")	-	53900	-
Cl 5.2(Design)	-	0	-
Cl 5.2.2, Table 4(" Height of upper ")	-	0	-
Cl 5.2.3(Heel area)	-	0	-
Cl 5.3.1.1(Construction of whole footwear)	-	0	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	0	-
Cl 5.3.2.1(Toe protection - general)	-	0	-
Cl 5.3.2.2(Internal length)	-	0	-
Cl 5.3.2.3(Width of toecap flange)	-	0	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	0	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	0	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	0	-
Cl 5.3.2.6(Impact resistance)	-	0	-
Cl 5.3.2.7(Compression resistance)	-	0	-
Cl 5.3.3(Leak proofness)	-	0	-
Cl 5.3.4("Specific ergonomic features ")	-	0	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	0	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	0	-
Cl 5.3.7(Seam strength)	-	0	-
Cl 5.3.8(Lead Content ( National Annex A))	-	0	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.2(Thickness)	-	0	-
Cl 5.4.3(Tear strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	0	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	0	-
Cl 5.4.5(Flexing resistance)	-	0	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	0	-
Cl 5.4.7(Resistance to hydrolysis)	-	0	-
Cl 5.5.2(Lining- Tear strength)	-	0	-
Cl 5.5.3(Lining- Abrasion resistance)	-	0	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	0	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	0	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	0	-
Cl 5.7.2(Water permeability of insock)	-	0	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	0	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	0	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	0	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	0	-
Cl 5.8.2.2(Cleated area)	-	0	-
Cl 5.8.2.3(Cleat height)	-	0	-
Cl 5.8.3(Outsole- Tear strength)	-	0	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	0	-
Cl 5.8.5(Outsole-Flexing resistance)	-	0	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	0	-
Cl 5.8.7(Interlayer bond strength)	-	0	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	0	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	0	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	0	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	0	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	0	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	0	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	0	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	0	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	0	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	0	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	0	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	0	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	0	-
Cl 6.2.4(Energy absorption of seat region)	-	0	-
Cl 6.2.5(Water resistance)	-	0	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	0	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	0	-
Cl 6.2.7(Ankle protection)	-	0	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	0	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	0	-
Cl 6.2.8.3(Resistance to cutting)	-	0	-
Cl 6.2.9(Scuff cap)	-	0	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	0	-
Cl 6.3(Upper — Water penetration and absorption)	-	0	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	0	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	0	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	0	-
Cl 6.4.3.2(Design of Ladder grip)	-	0	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	0	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	0	-
Cl 7, Table 20("Marking ")	-	0	-
Cl 5.2(Design)	-	-	-
Cl 5.2.2, Table 4(" Height of upper ")	-	-	-
Cl 5.2.3(Heel area)	-	-	-
Cl 5.3.1.1(Construction of whole footwear)	-	-	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	-	-
Cl 5.3.2.1(Toe protection - general)	-	-	-
Cl 5.3.2.2(Internal length)	-	-	-
Cl 5.3.2.3(Width of toecap flange)	-	-	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	-	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	-	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	-	-
Cl 5.3.2.6(Impact resistance)	-	-	-
Cl 5.3.2.7(Compression resistance)	-	-	-
Cl 5.3.3(Leak proofness)	-	-	-
Cl 5.3.4("Specific ergonomic features ")	-	-	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	-	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	-	-
Cl 5.3.7(Seam strength)	-	-	-
Cl 5.3.8(Lead Content ( National Annex A))	-	-	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	-	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	-	-
Cl 5.4.2(Thickness)	-	-	-
Cl 5.4.3(Tear strength)	-	-	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	-	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	-	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-	-
Cl 5.4.5(Flexing resistance)	-	-	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	-	-
Cl 5.4.7(Resistance to hydrolysis)	-	-	-
Cl 5.5.2(Lining- Tear strength)	-	-	-
Cl 5.5.3(Lining- Abrasion resistance)	-	-	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	-	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	-	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	-	-
Cl 5.7.2(Water permeability of insock)	-	-	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	-	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	-	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	-	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	-	-
Cl 5.8.2.2(Cleated area)	-	-	-
Cl 5.8.2.3(Cleat height)	-	-	-
Cl 5.8.3(Outsole- Tear strength)	-	-	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	-	-
Cl 5.8.5(Outsole-Flexing resistance)	-	-	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	-	-
Cl 5.8.7(Interlayer bond strength)	-	-	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	-	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	-	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	-	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	-	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	-	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	-	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	-	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	-	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	-	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	-	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	-	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	-	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	-	-
Cl 6.2.4(Energy absorption of seat region)	-	-	-
Cl 6.2.5(Water resistance)	-	-	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	-	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	-	-
Cl 6.2.7(Ankle protection)	-	-	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	-	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	-	-
Cl 6.2.8.3(Resistance to cutting)	-	-	-
Cl 6.2.9(Scuff cap)	-	-	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	-	-
Cl 6.3(Upper — Water penetration and absorption)	-	-	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	-	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	-	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	-	-
Cl 6.4.3.2(Design of Ladder grip)	-	-	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	-	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	-	-
Cl 7, Table 20("Marking ")	-	-	-

Complete

25 Feb, 2027

-
Included w.e.f 13.03.2025

IS 9550 (2024)

Bright Steel Bars — Specification

ALL

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(Supply of material and product designation)	-	14900	-
Cl-6(Chemical Composition)	-	14900	-
Cl-7(mechanical properties)	-	14900	-
Cl-8.1(Dimensions)	-	14900	-
Cl-8.2.1, Table-1(Cold drawn or heattreated and cold drawn)	-	14900	-
Cl-8.2.1, Table-1(Cold drawn, heat treated)	-	14900	-
Cl-8.2.1, Table-1(Peeled/turned)	-	14900	-
Cl-8.2.1, Table-1(Polished)	-	14900	-
Cl-8.2.1.1(Tolerances on dimensions)	-	14900	-
Cl-8.2.2, Table-2 (i)(Manufacturing lengtha)	-	14900	-
Cl-8.2.2, Table-2 (ii)(Stock lengtha)	-	14900	-
Cl-8.2.2, Table-2 (iii)(Cut to length)	-	14900	-
Cl-9(Surface condiotn)	-	14900	-
Cl-14(Marking)	-	14900	-
Clause. 6.0(chemical composition)	-	14900	-
Clause. 6.0(Sillicon)	-	14900	-
Clause. 6.0(Carbon)	-	14900	-
Clause. 6.0(Copper)	-	14900	-
Clause. 6.0(Manganese)	-	14900	-
Clause. 6.0(Molybdenum)	-	14900	-
Clause. 6.0(Chromium)	-	14900	-
Clause. 6.0(Nickel)	-	14900	-
Clause. 6.0(Sulphur)	-	14900	-
Clause. 6.0(Phosphorus)	-	14900	-
Clause. 6.0(Vanadium)	-	14900	-
Clause. 6.0(Titanium)	-	14900	-
Clause. 6.0(Boron)	-	14900	-
Clause. 6.0(Aluminium)	-	14900	-
Clause. 7.0(Brinell Hardness)	-	14900	-
Clause. 7.0(Tensile test)	-	14900	-
Clause. 7.0(Yeild stress)	-	14900	-
Clause. 7.0(Elongation)	-	14900	-
Clause. 8.0(Dimension)	-	14900	-
Clause. 8.0(Tolerence)	-	14900	-
clause. 9.0(Surface condition)	-	14900	-
clause. 9.0(Decarburization)	-	14900	-
clause.-10.0(Sampling)	-	14900	-
clause.- 11.0(other tests)	-	14900	-
Clause. -12.0(Retest)	-	14900	-
Clasue.- 13.0(Surface Protection)	-	14900	-
Clasue.- 14.0(Marking)	-	14900	-

Complete

25 Feb, 2027

-
-

IS 1469 (1993)

Ferromolybdenum - Specification (Fourth Revision)

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause-6(Supply of Materials)	-	-
Clause-7.1(Constitution of Consignment)	-	-
Clause-8.1(Mo)	-	-
Clause-8.1(C, Max)	-	-
Clause-8.1(Si, Max)	-	-
Clause-8.1(S, Max)	-	-
Clause-8.1(P Max)	-	-
Clause-8.1(Du Max)	-	-
Clause-8.1(Al Max)	-	-
Clause-8.1(Pb Max)	-	-
Clause-8.1(Sn Max)	-	-
Clause-8.4(Established instrumental/chemical method)	-	-
Clause-9(Size Range)	-	-
Clause-12(Marking)	-	-
Clause-6(Supply of Materials)	-	-
Clause-7.1(Constitution of Consignment)	-	-
Clause-8.1(Mo)	-	-
Clause-8.1(C, Max)	-	-
Clause-8.1(Si, Max)	-	-
Clause-8.1(S, Max)	-	-
Clause-8.1(P Max)	-	-
Clause-8.1(Du Max)	-	-
Clause-8.1(Al Max)	-	-
Clause-8.1(Pb Max)	-	-
Clause-8.1(Sn Max)	-	-
Clause-8.4(Established instrumental/chemical method)	-	-
Clause-9(Size Range)	-	-
Clause-12(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 20.03.2025

IS 1466 (1985)

Specification for ferrovanadium (Third Revision)

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause-2.1(Ferro Vanadium)	-	-
Clause-3(Grades)	-	-
Clause-5(Chemical Composition)	-	-
Clause-6(Norminal size Ranges)	-	-
Clause-9(Marking)	-	-
3 & 5(V)	-	-
3 & 5(Si)	-	-
3 & 5(C)	-	-
3 & 5(S)	-	-
3 & 5(P)	-	-
3 & 5(Al)	-	-
3 & 5(Mn)	-	-
3 & 5(Cr)	-	-
3 & 5(Cu)	-	-
3 & 5(Ni)	-	-
3 & 5(Pb)	-	-
3 & 5(Sn)	-	-
3 & 5(Zn)	-	-
3 & 5(Mo)	-	-
3 & 5(Ti)	-	-
Clause-4(Supply of Material)	-	-

Complete

25 Feb, 2027

-
Included w.e.f. 20.03.2025

IS 18476 (2023)

Fasteners ï¿½ Hexagon Washer Head Drilling Screws with Tapping Screw Thread

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause. 4.0(Dimenssions.)	-	-
Clause. 4.0(Thread size.)	-	-
Clause. 4.0(Length)	-	-
Clause. 5.0(Material)	-	-
Clause. 5.0(Thread)	-	-
Clause. 5.0(Tolerances)	-	-
Clause. 5.0(Mechnical and functional properties.)	-	-
Clause. 5.0(Finish)	-	-
Clause. 5.0(Acceptability)	-	-
Clause.6.0(Designation)	-	-
Clause.6.0(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 16.04.2025

IS 18471 : Part 3 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 3 Raised Countersunk Head

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Material)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross recesses)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 28.03.2025

IS 18471 : Part 2 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 2 Countersunk Head

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Material)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross recesses)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 28.03.2025

IS 18471 : Part 1 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 1 Pan Head

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Material)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross recesses)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 28.03.2025

IS 14756 (2024)

Stainless Steel Utensils - Specification (THIRD REVISION)

24900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(Material used for manufacturing utensils)	-	0	-
Cl 3.2(Material used for composite bottom)	-	0	-
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	0	-
Cl 3.4(Material used for stainless steel lid)	-	0	-
Cl 3.5(Material used for tempered glass lid)	-	0	-
Cl 3.5(Material used for stainless steel rim)	-	0	-
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	1500	-
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	1500	-
Cl 4.2(Thickness of the finished utensil)	-	1500	-
Cl 4.3(Classification)	-	500	-
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	1500	-
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	1500	-
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	1500	-
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	1500	-
Cl 5.1(Manufacturing defect & visual appearance)	-	1000	-
CL 5.2(Accessibility for cleaning)	-	1000	-
Cl 5.3(Joining of handles to the utensils)	-	2500	-
Cl 5.4(Requirement for handles)	-	12000	-
Cl 5.5(Welding (Finish))	-	1000	-
Cl 5.6(Finish of 3-ply utensil)	-	1000	-
Cl 5.7(Requirement for coating)	-	1000	-
Cl 5.8(Coating thickness test)	-	1500	-
Cl 5.8(Coating adhesion test)	-	1500	-
Cl 5.8.1(Thermal shock test (Coating))	-	4000	-
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	4000	-
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	1500	-
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	5000	-
Cl 6.7(Nominal Capacity Test)	-	1000	-
Cl 8(Marking)	-	0	-
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	1500	-
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	1500	-
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	2000	-
Cl 3.1(Material used for manufacturing utensils)	-	0	-
Cl 3.2(Material used for composite bottom)	-	0	-
Cl 3.3(Material used for body of utensil of 3-ply construction)	-	0	-
Cl 3.4(Material used for stainless steel lid)	-	0	-
Cl 3.5(Material used for tempered glass lid)	-	0	-
Cl 3.5(Material used for stainless steel rim)	-	0	-
Cl 4.2 & Table 1(Minimum Sheet Thickness for Body of Utensil)	-	0	-
Cl 4.2 & Table 2(Minimum Sheet Thickness for Lid of Utensil)	-	0	-
Cl 4.2(Thickness of the finished utensil)	-	0	-
Cl 4.3(Classification)	-	0	-
Cl 4.4 (i)(Thickness of Aluminium disc/core)	-	0	-
Cl 4.4 (ii)(Thickness of Protector/cowl)	-	0	-
Cl 4.5(Minimum sheet thickness (3-ply utensil))	-	0	-
Cl 4.5(Thickness of finished utensil (3-ply utensil))	-	0	-
Cl 5.1(Manufacturing defect & visual appearance)	-	0	-
CL 5.2(Accessibility for cleaning)	-	0	-
Cl 5.3(Joining of handles to the utensils)	-	0	-
Cl 5.4(Requirement for handles)	-	0	-
Cl 5.5(Welding (Finish))	-	0	-
Cl 5.6(Finish of 3-ply utensil)	-	0	-
Cl 5.7(Requirement for coating)	-	0	-
Cl 5.8(Coating thickness test)	-	0	-
Cl 5.8(Coating adhesion test)	-	0	-
Cl 5.8.1(Thermal shock test (Coating))	-	0	-
Cl 6.4(Dry Heat Test (for Cladded Utensils Only))	-	0	-
Cl 6.5(Coating Thickness Test (for Copper Deposit))	-	0	-
Cl 6.6(Thermal shock test (3-ply construction utensil body))	-	0	-
Cl 6.7(Nominal Capacity Test)	-	0	-
Cl 8(Marking)	-	0	-
Cl 6.1(Staining Test (Type Test - Frequency Once in a Year))	-	0	-
Cl 6.2(Mechanical Shock Test (for Cladded Utensils Only))	-	0	-
Cl 6.3(Thermal Shock Test (for Cladded Utensils Only))	-	0	-

Complete

25 Feb, 2027

-
-

IS 18480 : Part 3 (2023)

Cross Recessed Tapping Screw Part 3 Raised Countersunk Oval Head

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Material)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross Recess)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 28.03.2025

IS 18480 : Part 2 (2023)

Cross Recessed Tapping Screws Part 2 Countersunk Flat Head

19900 View breakup
-

Clause No.	Exclusion	Remark
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Material)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross Recess)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Material)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross Recess)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Material)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross Recess)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 28.03.2025

IS 18480 : Part 1 (2023)

Cross Recessed Tapping Screws: Part 1 Pan Head

20900 View breakup
-

Clause No.	Exclusion	Remark
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross Recess)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-
Clause. 4.0(Material)	-	-
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross Recess)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-
Clause. 4.0(Material)	-	-
Clause. 3.0(Dimenssions.)	-	-
Clause. 3.0(Thread size.)	-	-
Clause. 3.0(Length)	-	-
Clause. 4.0(Thread)	-	-
Clause. 4.0(Cross Recess)	-	-
Clause. 4.0(Tolerances)	-	-
Clause. 4.0(Mechnical and functional properties.)	-	-
Clause. 4.0(Finish)	-	-
Clause. 4.0(Acceptability)	-	-
Clause.5.0(Designation)	-	-
Clause.5.0(Marking)	-	-
Clause. 4.0(Material)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 28.03.2025

IS 11329 (2018)

Finned type heat exchanger for room air conditioner (First Revision)

ALL

217000 View breakup
-

Clause No.	Exclusion	Remark
4(CLASSIFICATION AND NOMENCLATURE)	-	-
5(MATERIALS)	-	-
6(QUALITY REQUIREMENTS)	-	-
7(TESTING)	-	-
7.1("Permissible Assembly Contamination Specification")	-	-
7.1.1(Internal Contamination)	-	-
7.2(Pressure Test for Assembly Tightness)	-	-
7.2.1(Water Leak Test)	-	-
7.2.2(Helium Leak Test)	-	-
7.2.3(Vacuum Leak Test Process)	-	-
7.3(Test for Mechanical Strength)	-	-
7.3.1(Burst Test)	-	-
7.3.2(Fatigue Strength Test)	-	-
7.4(Test for Corrosion Resistance)	-	-
8(MARKING)	-	-
9()	-	-
7.1.2(Moisture content)	-	-

Complete

25 Feb, 2027

-
Included w.e.f 28.03.2025

IS 13098 (2024)

AUTOMOTIVE VEHICLES TUBES FOR PNEUMATIC TYRES â SPECIFICATION (second revision)

ALL

19800 View breakup
-

Clause No.	Exclusion	Remark
Cl 3.1(Materials)	-	-
Cl 3.2(Classification)	-	-
Cl 3.2.1(Blend Name)	-	-
Cl 3.3(Fit)	-	-
Cl 3.3.1(Thickness Uniformity)	-	-
Cl 4.1.1(Elongation)	-	-
Cl 4.1.2(Strength of Splice)	-	-
Cl 4.1.3(Set After Ageing)	-	-
Cl 4.1.4(Accelerated Ageing)	-	-
Cl 5(AIR TIGHTNESS)	-	-
Cl 6(MARKING)	-	-
Cl 3.1(Materials)	-	-
Cl 3.2(Classification)	-	-
Cl 3.2.1(Blend Name)	-	-
Cl 3.3(Fit)	-	-
Cl 3.3.1(Thickness Uniformity)	-	-
Cl 4.1.1(Elongation)	-	-
Cl 4.1.2(Strength of Splice)	-	-
Cl 4.1.3(Set After Ageing)	-	-
Cl 4.1.4(Accelerated Ageing)	-	-
Cl 5(AIR TIGHTNESS)	-	-
Cl 6(MARKING)	-	-

Complete

25 Feb, 2027

-
-

IS 2046 (1995)

Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

28000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 , Table 1(CLASSIFICATION)	-	0	-
5.1(Colour and Pattern)	-	500	-
5.2(Surface Finish)	-	1000	-
5.2.2(Reverse side/Bonding)	-	0	-
5.3 ,Table 5(Thickness)	-	1000	-
5.4(Appearance )	-	0	-
5.2.2(Sports, dirt and similar surface defects)	-	0	-
5.2.2(Fibres,hairs,scratches)	-	0	-
5.2.2(Accumulated(Combination)of surface defects)	-	0	-
5.2.2(Edge Defects)	-	0	-
5.2.2(Broken Corners )	-	0	-
5.4.4(Sanding Defects)	-	1000	-
5.4.5 table 6(W arping (Flatness ))	-	1500	-
5.4.6 (Length and width of a full size Laminate)	-	1000	-
5.4.7,Fig. 2(Staightness of Edges)	-	1500	-
5.4.8, Fig.3(Squareness of the Laminates)	-	1500	-
5.5, Tables 7, Sr No.(i) Annex C(Resistance to Surface wear)	-	1500	-
5.5, Tables 7, Sr No.(ii) Annex D(Resistance to immersin in boiling water)	-	1500	-
5.5, Tables 7, Sr No.(iii) Annex E(Resistance to Dry heat at 180 °C)	-	1500	-
5.5, Tables 7, Sr No.(iv) Annex F(Dimensional Stability at deviated Temperature)	-	2000	-
5.5, Tables 7, Sr No.(v) Annex G(Dimensional Stability at 20°C)	-	2000	-
5.5, Tables 7, Sr No.(vi) Annex G(Resistance to impact by small diameter ball)	-	1500	-
5.5, Tables 7, Sr No.(vii) Annex J(Resistance to impact by large diameter balls (self supporting compact laminates))	-	1500	-
5.5, Tables 7, Sr No.(viii) Annex K(Resistance to cracking (thin laminates))	-	1500	-
5.5, Tables 7, Sr No.(ix) Annex B & E(Resistance to scratching)	-	1500	-
5.5, Tables 7, Sr No.(x) Annex -M(Resistance to staining)	-	2500	-
5.5, Tables 7, Sr No.(x) Annex -N (alternative)(Resistance to colour change)	-	0	-
5.5, Tables 7, Sr No.(x) Annex -O (alternative)(Resistance to colour change)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -P (alternative)(Resistance to Cigarette burns)	-	4000	-
5.5, Tables 7, Sr No.(xi) Annex -Q (alternative)(Resistance to Cigarette burns)	-	0	-
5.5, Tables 7, Sr No.(xi) Annex -R (Formability Method A)	-	0	-
5.5, Tables 7, Sr No.(xiv) Annex -R (Formability Method B)	-	1500	-
5.5, Tables 7, Sr No.(xv) Annex -T (Resistance to steam)	-	1500	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method A)	-	1500	-
5.5, Tables 7, Sr No.(xiv) Annex -S (Resistance to Blistering Method B)	-	0	-
5.5, Tables 7, Sr No.(xvi) Annex -N (Resistance to crazing (Thick laminates))	-	1500	-
5.5, Tables 7, Sr No.(xvii) Annex -Y (Resistance to moisture (Double faced compact laminates))	-	1500	-
5.5, Tables 7, Sr No.(xviii) Annex -F of IS 13401 (Flexural Modulus)	-	2000	-
5.5, Tables 7, Sr No.(xix) Annex -F of IS 13401 (Flexural Strength)	-	2000	-
5.5, Tables 7, Sr No.(xx) IS 8543 (Part4/Sec1) (Tensile Strength)	-	2000	-
7.2 a)(Marking)	-	0	-
7.2 b)(Marking)	-	0	-
7.2 c)(Marking)	-	0	-
7.2 d)(Marking)	-	0	-
7.2.1(Marking)	-	0	-

Complete

25 Feb, 2027

-
-

IS 10951 (2020)

Specification for Polypropylene ( PP ) Materials for Moulding and Extrusion ( Second Revision )

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.5.1,Table-3 or Clause 6.2.1.1(Melt Mass Flow-Rate (MFR) or Melt Flow Index,g/10min,IS 13360 (Part 4/Sec 1)/ASTM D1238)	-	3000	Test charges for Clause 4 (Sample preparation) - Rs.8000/- Test charges for Clause 5 (Conditioning) - Rs.2000/-
Clause 3.5.2,Table-4 or Clause 6.2.1.2(Flexural Modulus,Mpa,IS 13360 (Part 5/ Sec 7),ASTM D790)	-	4000	-
Clause 3.5.3,Table-5 or Clause 6.2.1.3(Izod Impact Strength,J/m,IS 13360 (Part 5/Sec 4)/ASTM D256)	-	4000	-
Clause 6.3.2,Table-8, Sl no.1(Tensile yield strength, Mpa,IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	8000	Rs. 8000/- for complete testing as per Sl. no. 1 Table -8
Clause 6.3.2,Table-8, Sl no.1(Elongation at yield, %, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	0	-
Clause 6.3.2,Table-8, Sl no.1(Tensile strength at break, Mpa, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	0	-
Clause 6.3.2,Table-8, Sl no.1(Elongation at break, percent, IS 13360 (Part 5/Sec 1) and IS 13360 (Part 5/Sec 2))	-	0	-
Clause 6.3.2,Table-8, Sl no.1(Charpy impact strength, KJ/m2, IS 13360 (Part 5/Sec 5))	-	0	-
Clause 6.3.2,Table-8, Sl no.1(Hardness – Rockwell R, Shore D,IS 13360 (Part 5/Sec 13),IS 13360 (Part 5/Sec 11))	-	0	-
Clause 6.3.2,Table-8, Sl no.2(Melting temperature,ᴼC,IS 13360 (Part 6/Sec 10))	-	10000	Rs. 10,000/- for complete testing as per Sl. no. 2 Table -8
Clause 6.3.2,Table-8, Sl no.2(Temperature of deflection under load,°C,IS 13360 (Part 6/ Sec 3),IS 13360 (Part 6/ Sec 17))	-	0	-
Clause 6.3.2,Table-8, Sl no.2(Vicat softening temperature, ᴼC,S 13360 (Part 6/Sec 1))	-	0	-
Clause 6.3.2,Table-8, Sl no.2(Flammability, mm/min,IS/ IEC 60695-11-10)	-	0	-
Clause 6.3.2,Table-8, Sl no.2(Ignitability (Oxygen index), percent,IS 13360 (Part 6/Sec 19))	-	0	-
Clause 6.3.2,Table-8, Sl no.3(Relative permittivity,IS 4486,IS 13360 (Part 7/Sec 1))	-	8000	Rs. 8000/- for complete testing as per Sl. no. 3 Table -8
Clause 6.3.2,Table-8, Sl no.3(Dissipation factor,IS 4486,IS 13360 (Part 7/Sec 1))	-	0	-
Clause 6.3.2,Table-8, Sl no.3(Volume resistivity,IS 2071 (Part 1))	-	0	-
Clause 6.3.2,Table-8, Sl no.3(Surface resistivity,IS 2071 (Part 1))	-	0	-
Clause 6.3.2,Table-8, Sl no.3(Dielectric strength,IS 2584)	-	0	-
Clause 6.3.2,Table-8, Sl no.4(Water absorption,%,IS 13360 (Part 8/ Sec 1))	-	5000	Rs. 5000/- for complete testing as per Sl. no. 4 Table -8
Clause 6.3.2,Table-8, Sl no.4(Density,kg/m3,IS 13360 (Part 3/ Sec 10),IS 13360 (Part 3/ Sec 11))	-	0	-
Clause 6.4.1(All additives used in the material which is meant,for usage in contact with foodstuffs, pharmaceuticals,and drinking water are given in IS 16738 for guidance purpose only.)	-	0	-
Clause 6.4.2(When the products are used in contact with ,foodstuffs, pharmaceuticals and drinking water, its requirements with respect to the material shall also be met as per clause 3.3, 3.4 and 3.5 of IS 10910.)	-	0	For charges refer to IS 10910
Clause 6.4.2(Pigments and colourants, IS 9833, Annex D.1)	-	0	For charges refer to IS 10910
Clause 6.4.2(Overall Migration, IS 9845, Annex D.2)	-	0	For charges refer to IS 10910
6.1(The material shall be uniform and free from foreign matter.)	-	1500	-

Complete

25 Feb, 2027

-
-

IS 16011 (2012)

Aluminium and aluminium alloy foil for pharmaceutical packaging - Specification

9900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

25 Feb, 2027

-
-

IS 15477 (2019)

Adhesives for use with ceramic tiles and mosaics

19800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Classification)	-	0	-
5.1(Tensile Adhesion Strength )	-	3500	a) Tensile(dry) - Rs. 3500/- b) Tensile (wet) - Rs.3500/-
5.2(Shear Adhesion Strength )	-	3500	a) dry - Rs.3500/- b) Heat ageing - Rs.3500/- c) Wet - Rs. 3500/-
5.3(OpenTime)	-	3500	-
5.4(Adjustment Time)	-	3500	-
5.5(Slip (Required for Vertical Application Only))	-	5500	-
5.6(Deformability (Required for VerticalApplication Only))	-	7500	-
8.2(Marking)	-	0	-

Complete

25 Feb, 2027

-
-

IS 16481 (2022)

Textiles Synthetic Micro Fibres for Use in Cement Based Matrix Specification First Revision

62500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Types of Synthetic Fibres used in Secondary Reinforcement of Concrete)	-	0	-
4.2, Table 1, i)(Cross section)	-	2500	-
4.2, Table 1, ii)(Tensile strength)	-	2500	-
4.2, Table 1, iii)(Specific gravity)	-	2000	-
4.2, Table 1, iv)(Ultimate elongation)	-	2500	-
4.2, Table 1, v)(Melting Temperature)	-	5500	-
4.2, Table 1, vi)(Glass Transition Temperature)	-	5500	-
4.2, Table 2, i)(Equivalent fibre diameter,)	-	2500	-
4.2, Table 2, ii)(Length)	-	2500	-
4.2, Table 2, iii)(Aspect ratio)	-	2500	-
4.2, Table 3, i)(Drying shrinkage for concrete only)	-	8500	-
4.3(General)	-	2500	4.3) Rs.2500/- 4.3.2) Rs.1500/- 4.3.3) Rs.2000/-
4.4(Resistance to Alkalis)	-	3500	-
4.5(Resistance to Acids)	-	3500	-
4.6(Resistance to Ageing)	-	13500	-
4.7(Resistance to Ultraviolet Light)	-	15500	-
5(PACKING AND MARKING)	-	0	-
4.3.1(Isophthalic Acid (IPA) content)	-	2500	-

Complete

25 Feb, 2027

-
-

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Atmy Analytical Labs Pvt. Ltd.

I-30,DLF Industrial Area, Phase-1, Faridabad, Faridabad, Haryana, 121003

9910808996 info@atmylabs.com

Scope List

No Record Found