BIS - LIMS (Laboratory Information Management System)

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

A-29, Sector 5, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

9205030060 testing.a29@urs-labs.com

Scope List

Reset

127 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

13900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.24(Annexure E)(on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-	500	-
Cl.23(There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-	500	-
24 (Annex - E)(Combustion (CO and CO2 ratio))	-	500	-
4.1(Requirement)	-	500	-
5(Materials)	-	500	-
6(Design for Maintenance)	-	500	-
7(Rigidity and Stability)	-	500	-
8(Workmanship and Finish)	-	500	-
9(Gas Taps)	-	1000	-
10(Injector Jets)	-	1000	-
11(Burners)	-	1000	-
12(Burner Pan Supports)	-	1000	-
13.1(Gas Soundness)	-	500	-
13.2(Gas Leak Detector)	-	500	-
14(Gas Inlet Connections)	-	500	-
15(Strength and Rigidity)	-	500	-
16(General Conditions of Test)	-	500	-
17.1.1(Gas Consumption)	-	1000	-
18(Ignition and Flame Travel)	-	300	-
19(Flame Stability)	-	200	-
20(Noise Control)	-	200	-
21(Flash Back)	-	300	-
22(Formation of Soot)	-	200	-
23(Resistance to Draught)	-	300	-
24(Combustion)	-	500	-
25(Fire Hazard and Limiting Temperature)	-	500	-
26(Thermal Efficiency)	-	1000	-
27.1(Type Tests)	-	100	-
27.2(Routine Tests)	-	200	-
29(Marking)	-	100	-
30(Packing)	-	200	-
5.1.2(Toughened glass- Adhesive tape)	-	1000	-
5.1.3(Thermal Shock test)	-	1000	-

26 Sep, 2027

-
-

IS/IEC 61730 : PART 2 (2004)

Photovoltaic (PV) Module Safety Qualification Part 2 Requirements for Testing

800000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Visual Inspection (MST 01))	-	3000	-
10.2(Accessibility test (MST 11))	-	35000	-
10.3(Cut susceptibility test (MST 12))	-	25000	-
10.4(Ground Continuity Test (MST 13))	-	50000	-
10.5(Impulse voltage test (MST 14))	-	50000	-
10.6(Dielectric withstand test (MST 16))	-	55000	-
10.7(Temperature test (MST 21))	-	70000	-
10.8(Fire test (MST 23))	-	300000	-
10.9(Reverse Current overload test (MST 26))	-	50000	-
10.10(Module breakage test (MST 32))	-	50000	-
11.1(Partial discharge-test (MST 15))	-	45000	-
11.2(Conduit Bending test (MST 33))	-	35000	-
11.3(Terminal box knockout tests (MST 44))	-	32000	-
Cl.5, Table 7(Thermal cycling (T200) (MST 51))	-	150000	-
Cl.5, Table 7(Thermal cycling (T50) (MST 51))	-	75000	-
Cl.5, Table 7(Humidity freeze (10HF) (MST 52))	-	70000	-
Cl.5, Table 7(Damp heat (DH1000) (MST 53))	-	125000	-
Cl.5, Table 7(UV resistance (MST 54))	-	70000	-
Cl.5, Table 7(Wet leakage current test (MST 17))	-	5000	-
Cl.5, Table 7(Hot spot test (MST 22))	-	15000	-
Cl.5, Table 7(Mechanical load test (MST 34))	-	45000	-

26 Sep, 2027

-
-

IS 14434 (2023)

POLYCARBONATE MOULDING AND EXTRUSION MATERIALS SPECIFICATION

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.2.2(Filler Content)	-	1000	-
5(Melt Volume-Flow Rate (MVR))	-	1000	-
5.2(Specific Gravity)	-	1000	-
5.3(Flexural Modulus)	-	1000	-
5.4(Charpy Impact Strength, Notched)	-	1000	-
5.5(Deflection Temperature Under 1.82 MPa)	-	1000	-
5.6.1.2(Overall migration)	-	1000	-
4.2.5(Flammability)	-	1000	-
4.2.5(Optical Properties(% Transmittance))	-	1000	-
4.1(General)	-	1000	-
4.2.2.1(Data Block 2)	-	1000	-
4.2.2.2(Block 2)	-	1000	-
4.2.3(Data Block 3)	-	1000	-
4.2.4 (a)(Melt volume-flow rate)	-	1000	-
4.2.4 (b)(Specific gravity)	-	1000	-
4.2.4 (c)(Flexural modulus)	-	1000	-
4.2.4 (d)(Impact strength)	-	1000	-
4.2.4 (e)(Deflection temperature)	-	1000	-
5.6.1.1(Pigments and colourants)	-	1000	-
5.6.1.2(Overall migration)	-	1000	-
5.6.1.3(Storage and control)	-	1000	-
6(Preparation of Test Specimens)	-	1000	-
8(Packing and Marking)	-	1000	-
4.2.5.2 Table - 6 (i)(Volume resistivity, Min, ohm-cm)	-	1000	-
4.2.5.2 Table - 6 (ii)(Dielectric strength, Min, kV/mm)	-	1000	-
4.2.5.2 Table - 6 (iii)(Dielectric constant at 1 MHz, Max)	-	1000	-
4.2.5.2 Table - 6 (iv)(Dissipation factor at 1 MHz, Max)	-	1000	-
4.2.5.2 Table 6 Sr.No.(i)(Volume resistivity)	-	1000	-
4.2.5.2 Table 6 Sr.No.(ii)(Dielectric strength)	-	1000	-
4.2.5.2 Table 6 Sr.No.(ii)(Dielectric Constant)	-	1000	-
4.2.5.2 Table 6 Sr.No.(ii)(Dissipation factor)	-	1000	-

26 Sep, 2027

-
Included w.e.f 21.05.2025

IS 302 : Part 2 : Sec 80 (2017)

Household and similar electrical appliances - Safety: Part 2 - 80 particular requirements for fans (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
32.0(Radiation, Toxicity and Similar Hazards)	-	500	-
31.0(Resistance To Rusting)	-	500	-
30.0(Resistance To Heat and Fire)	-	1000	-
29.0(Creepage Distances and Clearances)	-	500	-
28.0(Screws and Connections)	-	500	-
27.0(Provision For Earthing)	-	500	-
26.0(Terminals for external conductors)	-	500	-
25.0(Supply Connection and External Flexible Cords)	-	500	-
24.0(Components)	-	500	-
23.0(Internal Wiring)	-	500	-
22.0(Construction)	-	500	-
21.0(Mechanical Strength)	-	500	-
20.0(Stability and mechanical hazards)	-	500	-
19.0(Abnormal Operation)	-	1000	-
17.0(Overload Protection of transformer and associated circuit)	-	500	-
16.0(Leakage current and Electric strength (After Humidity (Environmental) Treatment))	-	1000	-
15.0(Moisture resistance)	-	2000	-
14.0(Transient Overvoltage)	-	500	-
13.0(Leakage Current and electric strength at operating temperature)	-	1000	-
11.0(Heating)	-	2000	-
10.0(Input and Current)	-	1000	-
8.0(Protection against access to live parts)	-	500	-
7.0(Classification)	-	500	-
6.0(Marking and Instructions)	-	500	-

26 Sep, 2027

-
Exclusion: EMI/EMC test

IS 13995 (1995)

Unlined moulded rubber boots - Specification

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Thickness )	-	200	-
5.1.1(Tensile Strength (before ageing))	-	500	-
5.1.2(Tensile Strength (after ageing))	-	2000	-
5.1.3(Tear Strength)	-	1000	-
5.1.4(Resistance to dry heat ageing )	-	1000	-
5.1.5(Flexing resistance of upper)	-	1000	-
5.1.6(Design)	-	100	-
5.1.7(Size)	-	100	-

26 Sep, 2027

-
-

IS 17043 (2018)

Derby shoes - Specification

54900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1(Physical Requirements for Derby Shoes)	-	100	-
4.1(General)	-	100	-
4.2(Design )	-	100	-
4.3.1(Size)	-	100	-
4.3.2(Weight)	-	500	-
4.4(Height of upper )	-	100	-
4.5.1(Contruction)	-	100	-
4.5.2(Ergonomic Feature)	-	500	-
4.5.3.1(Upper/outsole bond strength)	-	1000	-
4.5.3.2(Interayer bond strength)	-	1000	-
4.5.4(Slip Resitance)	-	800	-
4.5.5.1(Electrical Properties Antistatic )	-	2000	-
4.5.6(Heat insulation of sole complex)	-	1000	-
4.5.7(Cold insulation tester )	-	1000	-
4.5.8(Energy absorption of seat region )	-	1000	-
4.6.1(Thickness )	-	100	-
4.6.2(Tear Strength)	-	500	-
4.6.3(Water vapour permeability & coefficent )	-	1000	-
4.6.4(Water penetration and water absorption)	-	1000	-
4.7.1(Thickness )	-	100	-
4.7.2(Tear Strength)	-	500	-
4.7.3(Abrasion resistance )	-	1000	-
4.7.4(Water vapour permeability & coefficent )	-	1000	-
4.8.1(Thickness )	-	100	-
4.8.2(Abrasion )	-	1000	-
4.8.3(Water absorption & desorption )	-	1000	-
4.9.1(Thickness )	-	100	-
4.9.2(Water absorption & desorption )	-	1000	-
4.9.3(Abrasion resistance )	-	1000	-
4.10(Toe Puff & counter stiffener thickness )	-	500	-
4.11.1(Thickness )	-	100	-
4.11.2(Tear Strength)	-	500	-
4.12(Breaking Strength of thread)	-	1000	-
4.13.1(Meterial)	-	100	-
4.13.2(Thickness )	-	100	-
4.13.3(Density )	-	500	-
4.13.4(Hardness (IRHD))	-	500	-
4.13.5(Ageing test)	-	2000	-
4.13.6(Tear Strength)	-	1000	-
4.13.7(Abrasion resistance )	-	1000	-
4.13.8(Flex resistance )	-	1000	-
4.14(Eyelet pull out test)	-	500	-
4.15.1(Length of laces )	-	200	-
4.15.2(Breaking load & tag retention)	-	1000	-
5.0(Innocuosness test IS 17011)	-	25000	-

26 Sep, 2027

-
-

IS 555 (1979)

Specification for electric table type fans and regulators (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.16(Creepage Distances and Clearances)	-	500	-
10.14(Cord Grip Test)	-	500	-
10.13, 7.4(Mechanical Endurance Test (for Regulators Only))	-	500	-
10.12(Moisture Resistance Test)	-	1000	-
10.11(Protection against Electric Shock)	-	500	-
10.1(Earthing Connection)	-	500	-
10.9(Fan Speed and Input)	-	500	-
10.8(Construction)	-	500	-
10.7(Insulation-Resistance Test (Shall follow Moisture Resistance Test Cl.10.12))	-	500	-
10.6(High Voltage Test)	-	500	-
10.5(Leakage Current)	-	500	-
10.4(Temperature-Rise Test)	-	1000	-
10.3(Air Delivery Test)	-	3000	-
9.0(Marking)	-	300	-
7.11(Oscillating Mechanism)	-	500	-
7.9(Interchangeability)	-	200	-
7.8(Speed Regulators)	-	500	-
6.0(Design and General Construction)	-	300	-
5.0(Rated Frequency)	-	50	-
4.0(Rated Voltages)	-	50	-
3.0(Size, Speed and Types)	-	50	-

26 Sep, 2027

-
-

IS/IEC 61730 : PART 1 (2016)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction ( First Revision )

1225000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 IS/IEC 61730-1(Marking and Documentation)	-	2000	-
5.3, 5.3.1 IS/IEC 61730-1(Electrical Components and Insualtion)	-	3000	-
5.3.6 IS/IEC 61730-1(Front sheet and back Sheet)	-	25000	-
5.3.7 IS/IEC 61730-1(Insulation Barrier)	-	20000	-
5.3.8 IS/IEC 61730-1(Electrical Connections)	-	25000	-
5.3.9 IS/IEC 61730-1(Encapsulants)	-	25000	-
5.3.10 IS/IEC 61730-1(Bypass Diodes)	-	25000	-
5.4, 5.4.1 IS/IEC 61730-1(Mechanical and Electromechanical connections)	-	100000	-
5.4.2 IS/IEC 61730-1(Screw Connctions)	-	25000	-
5.4.3 IS/IEC 61730-1(Rivets)	-	10000	-
5.4.5 IS/IEC 61730-1(Form/Press/Tight/Fit)	-	10000	-
5.4.6 IS/IEC 61730-1(Connections by adhesives)	-	10000	-
5.4.7 IS/IEC 61730-1(Other Connections)	-	25000	-
5.5, 5.5.1 IS/IEC 61730-1(Materials)	-	50000	-
5.5.2 IS/IEC 61730-1(Polymeric Materials)	-	100000	-
5.5.2.3.2 IS/IEC 61730-1(Endurance to Electrical Stress)	-	100000	-
5.5.2.3.3 IS/IEC 61730-1(Endurance to thermal stress-RTE (RTI) or TI)	-	150000	-
5.5.2.3.4 IS/IEC 61730-1(Polymeric Insulating materials used as external Parts)	-	75000	-
5.5.2.3.5 IS/IEC 61730-1(Polymeric Insulating Parts supporting live Parts)	-	100000	-
5.5.2.4 IS/IEC 61730-1(Polymeric Meterial used for Mechanical functions)	-	100000	-
5.5.3, 5.5.3.1 IS/IEC 61730-1(Metallic materials)	-	50000	-
5.5.4 IS/IEC 61730-1(Adhesives)	-	50000	-
5.6, 5.6.1 IS/IEC 61730-1(Protection Agianst Electric Shock)	-	35000	-
5.6.2 IS/IEC 61730-1(Protection Agianst accessibility to hazardeous live parts)	-	35000	-
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	25000	-
5.6.4 IS/IEC 61730-1(Distance through Insulation)	-	25000	-
5.6.3.4(Clearances and creepage distances)	-	25000	-

26 Sep, 2027

-
-

IS 374 (2019)

Specification for electric ceiling type fans and regulators (Third Revision)

26250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	500	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	500	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	500	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	500	-
8.1(Marking (as per Cl. 7 of IS 302-2-80:2017))	-	500	-
8.1,a(Marking )	-	20	-
8.1,b(Marking )	-	20	-
8.1,c(Marking )	-	20	-
8.1,d(Marking )	-	20	-
8.1,e(Marking )	-	20	-
8.1,f(Marking )	-	20	-
8.1,g(Marking )	-	20	-
8.2(Marking )	-	20	-
8.3,a(Marking )	-	20	-
8.3,b(Marking )	-	20	-
8.3,c(Marking )	-	20	-
8.3,d(Marking )	-	20	-
8.3,e(Marking )	-	20	-
8.4(Marking )	-	20	-
8(Marking (as per Cl. 7.1 of IS 302-2-80:2017))	-	20	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008))	-	20	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008))	-	20	-
8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017))	-	20	-
6.2(Rating)	-	20	-
9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017))	-	20	-
9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017))	-	20	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	20	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	20	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	20	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	20	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	20	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	20	-
9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017))	-	20	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	20	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	20	-
9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017))	-	20	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	20	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	20	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	20	-
9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017))	-	20	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	20	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	20	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017))	-	20	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	20	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	20	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	20	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	20	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	20	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	20	-
9(Construction (as per Cl.22.101 of IS 302-2-80 :2017))	-	20	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	20	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	20	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	20	-
9(Components (as per Cl.24.103 of IS 302-2-80 :2017))	-	20	-
9(Components (as per Cl.24.104 of IS 302-2-80 :2017))	-	20	-
9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017))	-	20	-
9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017))	-	20	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	20	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	20	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	20	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	20	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	20	-
9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017))	-	20	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	20	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	20	-
9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017))	-	20	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	20	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	20	-
10.1(Speed Regulators)	-	20	-
10.2(Speed Regulators)	-	20	-
10.2(Speed Regulators)	-	20	-
10.2(Speed Regulators)	-	20	-
10.3(Speed Regulators)	-	20	-
10.4(Speed Regulators)	-	20	-
10.5(Speed Regulators)	-	20	-
10.6(Speed Regulators)	-	20	-
10.7(Speed Regulators)	-	20	-
10.7(Speed Regulators)	-	20	-
10.8(Speed Regulators)	-	20	-
11.1(Starting)	-	20	-
11.2(Starting)	-	20	-
12(Interchangeability)	-	20	-
13(Silent Operation)	-	20	-
14.3 & Table 1(Test for Air Performance)	-	20	-
14.3 & Table 1(Test for Air Performance)	-	20	-
14.4(Measurement of Speed of the Fan )	-	20	-
14.4(Measurement of Speed of the Fan )	-	20	-
14.5(Measurement of Power factor and Power Input)	-	20	-
14.5(Measurement of Power factor and Power Input)	-	20	-
16(Endurance Test)	-	20	-
16(Endurance Test)	-	20	-
16(Endurance Test)	-	20	-
16(Endurance Test)	-	20	-
16(Endurance Test)	-	20	-
16(Endurance Test)	-	20	-
17(Test for Harmonic Distortion)	-	20	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	-	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	-	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	-	-
7(Classification (as per Cl.6 of IS 302-2-80 :2017))	-	-	-
8.1(Marking (as per Cl. 7 of IS 302-2-80:2017))	-	-	-
8.1,a(Marking )	-	-	-
8.1,b(Marking )	-	-	-
8.1,c(Marking )	-	-	-
8.1,d(Marking )	-	-	-
8.1,e(Marking )	-	-	-
8.1,f(Marking )	-	-	-
8.1,g(Marking )	-	-	-
8.2(Marking )	-	-	-
8.3,a(Marking )	-	-	-
8.3,b(Marking )	-	-	-
8.3,c(Marking )	-	-	-
8.3,d(Marking )	-	-	-
8.3,e(Marking )	-	-	-
8.4(Marking )	-	-	-
8(Marking (as per Cl. 7.1 of IS 302-2-80:2017))	-	-	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1 (f) of IS 302-1:2008))	-	-	-
8(Marking (as per Cl. 7 of IS 302-2-80:2017, Cl.7.1(g) of IS 302-1:2008))	-	-	-
8(Marking (as per Cl.7.12.1(a) of IS 302-2-80:2017))	-	-	-
6.2(Rating)	-	-	-
9(Protection against access to live parts (as per Cl.8 of IS 302-2-80 :2017))	-	-	-
9(Power Input & current (as per Cl.10 of IS 302-2-80 :2017))	-	-	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	-	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	-	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	-	-
9( Heating (as per Cl.11 of IS 302-2-80 :2017))	-	-	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	-	-
9(Leakage current and Electric strength at operating temperature (as per Cl.13 of IS 302-2-80 :2017))	-	-	-
9(Transient over Voltage (as per Cl.14 of IS 302-2-80 :2017))	-	-	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	-	-
9(Moisture Resistance (After Humidity test) (as per Cl.15 & Cl.16 of IS 302-2-80 :2017) )	-	-	-
9(Overload protection of transformers and associated circuits (as per Cl.17 of IS 302-2-80 :2017))	-	-	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	-	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	-	-
9( Abnormal Operation (as per Cl.19 of IS 302-2-80 :2017))	-	-	-
9(Staibilty and mechanical hazards (as per Cl.20.102, Table 101 of IS 302-2-80 :2017))	-	-	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	-	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017 and Cl.21.1 of IS 302-2:2008))	-	-	-
9(Mechanical strength (as per Cl.21 of IS 302-2-80 :2017))	-	-	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	-	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	-	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	-	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	-	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	-	-
9(Mechanical strength (as per Cl.21.102 of IS 302-2-80 :2017))	-	-	-
9(Construction (as per Cl.22.101 of IS 302-2-80 :2017))	-	-	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	-	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	-	-
9(Internal wiring (as per Cl.23 of IS 302-2-80 :2017 and Cl.23 of IS 302-1:2008))	-	-	-
9(Components (as per Cl.24.103 of IS 302-2-80 :2017))	-	-	-
9(Components (as per Cl.24.104 of IS 302-2-80 :2017))	-	-	-
9(Supply Connection and External Flexible cords (as per Cl.25 of IS 302-2-80 :2017))	-	-	-
9(Terminals for External conductors (as per Cl.26 of IS 302-2-80 :2017))	-	-	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	-	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	-	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	-	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	-	-
9(Provision for earthing (as per Cl.27 of IS 302-2-80 :2017))	-	-	-
9(Screw and connections (as per Cl.28 of IS 302-2-80 :2017))	-	-	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	-	-
9(Clearances, creepage distances and solid insulation (as per Cl.29 of IS 302-2-80 :2017))	-	-	-
9(Resistance to fire (Glow wire Test) (as per Cl.30 of IS 302-2-80 :2017))	-	-	-
9(Resistance to rusting (as per Cl.31 of IS 302-2-80 :2017))	-	-	-
9(Radiation, Toxicity and similar Hazards (Cl.32 of IS 302-2-80 :2017))	-	-	-
10.1(Speed Regulators)	-	-	-
10.2(Speed Regulators)	-	-	-
10.2(Speed Regulators)	-	-	-
10.2(Speed Regulators)	-	-	-
10.3(Speed Regulators)	-	-	-
10.4(Speed Regulators)	-	-	-
10.5(Speed Regulators)	-	-	-
10.6(Speed Regulators)	-	-	-
10.7(Speed Regulators)	-	-	-
10.7(Speed Regulators)	-	-	-
10.8(Speed Regulators)	-	-	-
11.1(Starting)	-	-	-
11.2(Starting)	-	-	-
12(Interchangeability)	-	-	-
13(Silent Operation)	-	-	-
14.3 & Table 1(Test for Air Performance)	-	-	-
14.3 & Table 1(Test for Air Performance)	-	-	-
14.4(Measurement of Speed of the Fan )	-	-	-
14.4(Measurement of Speed of the Fan )	-	-	-
14.5(Measurement of Power factor and Power Input)	-	-	-
14.5(Measurement of Power factor and Power Input)	-	-	-
16(Endurance Test)	-	-	-
16(Endurance Test)	-	-	-
16(Endurance Test)	-	-	-
16(Endurance Test)	-	-	-
16(Endurance Test)	-	-	-
16(Endurance Test)	-	-	-
17(Test for Harmonic Distortion)	-	-	-

26 Sep, 2027

-
Exclusion: Cl.19.11.4

IS 15298 : part 4 (2017)

Personal protective equipment: Part 4 occupational footwear (Second Revision)

53250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.2.1(General)	-	100	-
5.2.2.2(Height of upper)	-	100	-
5.2.2.3(Seat region)	-	100	-
5.3.2.1(Construction)	-	100	-
5.3.1.2(Upper/outsole bond strength)	-	1000	-
5.3.2.2(Leakproofness)	-	500	-
5.3.2.3(Specific ergonomic features )	-	500	-
5.3.4.1(Slip resistance)	-	800	-
5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (SLS) solution)	-	800	-
5.3.4.4(Slip resistance on ceramic tile floor with SLS and on steel floor with glycerine )	-	800	-
5.3.2.5(Innocuousness )	-	25000	-
5.4.2.1(Upper)	-	100	-
5.4.2.2(Thickness )	-	100	-
5.4.2.3(Tear strenth)	-	500	-
5.4.2.4(Tensile properties)	-	1000	-
5.4.2.5(Flexing resistance )	-	1000	-
5.4.2.6(Water vapour permeability and coefficient )	-	1000	-
5.4.2.7(pH value )	-	500	-
5.4.2.8(Hydrolysis)	-	1000	-
5.4.2.9(Chromium VI content )	-	500	-
5.5.2.1(Tear strength )	-	500	-
5.5.2.2(Abrasion resistance )	-	1000	-
5.5.2.3(Water vapour permeability and coefficient )	-	1000	-
5.5.2.4(pH value )	-	500	-
5.5.2.5(Chromium VI content )	-	500	-
5.6(Tongue )	-	100	-
5.6.2.1(Tear strength )	-	500	-
5.6.2.2(pH value )	-	500	-
5.6.2.3(Chromium VI content )	-	500	-
5.7.2.1(Insole and insock )	-	500	-
5.7.2.2(Insole and insock )	-	1000	-
5.7.2.3(Water absorption and desorption )	-	1000	-
5.7.4.1(Abrasion resistance )	-	1000	-
5.7.4.2(Abrasion resistance )	-	1000	-
5.7.2.5(Chromium VI content )	-	500	-
5.8.2.1(Outsole)	-	100	-
5.8.1.1(Thickness )	-	100	-
5.8.1.2(Cleated area )	-	100	-
5.8.1.3(Cleat height)	-	100	-
5.8.2.2(Tear strength )	-	100	-
5.8.2.3(Abrasion resistance )	-	1000	-
5.8.2.4(Flexing resistance )	-	1000	-
5.8.2.5(Hydrolysis )	-	100	-
5.8.2.6(Interlayer bond strength )	-	1000	-
6.2.1.1(Metallic anti-penetration insert )	-	1000	-
6.2.1.1.2(Non-metallic anti-penetration insert used as an insole)	-	1000	-
6.2.1.2(Construction)	-	500	-
6.2.1.3(Dimensions )	-	500	-
6.2.1.4(Flex resistance of penetration-resistant inserts )	-	1000	-
6.2.1.5.1(Corrosion resistance of penetration-resistant metallic inserts)	-	1000	-
6.2.1.5.2(Penetration-resistant non-metallic inserts)	-	1000	-
6.2.2.1(Conductive footwear)	-	1000	-
6.2.2.2(Antistatic footwear)	-	2000	-
6.2.2.3(Electrically insulating footwear )	-	1000	-
6.2.3.1(Heat insulation of sole complex )	-	1000	-
6.2.3.2(Cold insulation of sole complex)	-	1000	-
6.2.2.4(Energy absorption of seat region )	-	1000	-
6.2.2.5(Water resistance )	-	1000	-
6.2.7.1(Cut resistance foot wear)	-	1000	-
6.2.7.2(Cut resistance foot wear)	-	1000	-
6.3.2.2(Upper- water penetration)	-	1000	-
6.4.2.1(Resistance to hot contact)	-	1000	-
6.4.2.2(Resistance to fuel oil)	-	1000	-

26 Sep, 2027

-
-

IS 15298 : Part 3 (2019)

Personal protective equipment: Part 3 protective footwear (Second Revision)

54450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.2 Table-2(Height of upper)	-	100	-
5.2.3 Table-2(Seat Region)	-	100	-
5.3.1.1 Table-2(Construction)	-	100	-
5.3.1.2 Table-2(Upper/Outsole Bond)	-	800	-
5.3.2.1 Table-2(General)	-	100	-
5.3.2.2 Table-2(Internal Length of toe cap)	-	500	-
5.3.2.3 Table-2(Impact Resistance -T- )	-	1000	-
5.3.2.4 Table-2(Compression)	-	1000	-
5.3.2.5 Table-2(Behaviour of toe cap)	-	500	-
5.3.3 Table-2(Leak Proofness)	-	500	-
5.3.4 Table-2(Specific Ergonomic)	-	500	-
5.3.5.2 Table-2(Slip Resistance SRA)	-	800	-
5.3.5.3 Table-2(Slip Resistance SRB)	-	800	-
5.3.5.4 Table-2(Slip Resistance SRC)	-	800	-
5.4.1 Table-2(General)	-	100	-
5.4.2 Table-2(Thickness)	-	100	-
5 4 3 Table-2(Tear Strength)	-	500	-
5.4.4 Table-2(Tensile Properties)	-	1000	-
5.4.5 Table-2(Flexing Resistance)	-	1000	-
5.4.6 Table-2(Water Vapour Permeability & Coefficient)	-	1000	-
5 4.7 Table-2( )	-	100	-
5 4.8 Table-2(Hydrolysis)	-	1000	-
5.4 9 Table-2(Chrome VI)	-	500	-
5.5.1 Table-2(Tear Strength)	-	1000	-
5.5.2 Table-2(Abrasion Resistance)	-	1000	-
5.5.3 Table-2(Water Vapour Permeability & Coefficient)	-	1000	-
5.5.4 Table-2(pH Value)	-	500	-
5.5.5 Table-2(Chrome VI)	-	500	-
5.6.1 Table-2(Tear Strength)	-	1000	-
5.6.2 Table-2(pH Value)	-	500	-
5.6.3 Table-2(Chromium VI)	-	500	-
5.7.1 Table-3(Thickness)	-	100	-
5.7.2 Table-3(pH Value)	-	100	-
5.7.3 Table-3(Water Absorption &)	-	100	-
5.7.4.1 Table-3(Insole Abrasion)	-	500	-
5.7.4.2 Table-3(Abrasion)	-	1000	-
5.7.5 Table-3(Chromium VI)	-	500	-
5.8.1 Table-2(Design)	-	100	-
5.8.2 Table-2(Tear Strength)	-	500	-
5.8.3 Table-3(Abrasion Resistance)	-	1000	-
5.8.4 Table-3(Flexing Resistance)	-	1000	-
5.8.5 Table-3(Hydrolysis)	-	1000	-
5.8.6 Table-2(Interlayer BondStrength)	-	1000	-
6.2.1 Table-I8(Penetration Resistance)	-	1000	-
6.2.2.1 Table-18(Electrical Properties)	-	1000	-
6.2.2.2 Table-18(Antistatic Footwear)	-	2000	-
6.2.2.3 Table-18(Electrically Insulated)	-	1000	-
6.2.3.1 Table-18(Heat Insulated Comp)	-	1000	-
6.2.3.2 Table-18(Cold Insulated)	-	1000	-
6.2.4 Table-18(Energy Absorption of seat region)	-	500	-
6.2.5 Table-18(Water Resistance)	-	500	-
6.2.8 Table-18(Cut Resistance)	-	1000	-
6.3 Table-18(Water Penetration & Absorption)	-	1000	-
6.4.1 Table-18(Resistance to Hot Contact)	-	500	-
6.4.2 Table-18(Resistance to Fuel oil)	-	1000	-
Cl.5.8.1.2(Cleated area)	-	100	-
Cl.5.8.1.3(Cleat Height)	-	100	-

26 Sep, 2027

-
-

IS 15298 : Part 2 (2016)

Personal protective equipment: Part 2 safety footwear (Second Revision)

53000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4,Table 1(Class I, IS 15298)	-	100	-
4,Table 1(Class II, IS 15298)	-	100	-
5.2,5.2.1, Fig 3(Design,General, IS 15298)	-	100	-
5.2.2, Fig 4(Height of Upper, ISO 20344 , 6.2)	-	100	-
5.2.3, Table 10 ,Design A(Seat Region)	-	100	-
5.3.1.1(Construction)	-	100	-
5.3.1.2(Upper/outer sole bond strength , ISO 20344 , 5.2)	-	500	-
5.3.2.1(General, EN 12568 OF 4.2.2.2)	-	100	-
5.3.2.2,Table 5(Internal length of toecaps , ISO 20344 , 5.3)	-	300	-
5.3.2.3,Table 6(Impact resistance of safety footwear,ISO 20344 , 5.4)	-	1000	-
5.3.2.4 ,Table 6(Compression Resistance of safety footwear ,ISO20344 , 5.5)	-	1000	-
5.3.2.5.1(Corrosion resistance of metallic toecaps ,ISO20344 , 5.6.2)	-	500	-
5.3.2.5.2(Non metallic toe caps ,EN 12568)	-	500	-
5.3.3(Leak proofness ,ISO 20344 , 5.7)	-	500	-
5.3.4(Specific ergonomic feature ,ISO 20344 , 5.1)	-	500	-
5.3.5.2,Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1000	-
5.3.5.3,Table 8(Slip resistance on steel floor with glycerin)	-	1000	-
5.3.5.4(Slip resistance on ceramic tile floor with NaLS and on steel floor with glycerin)	-	1000	-
5.4.8(Hydrolysis ; ISO 20344,6.10)	-	1000	-
5.4.2, Table 11(Thickness , ISO 20344 , 6.1 )	-	300	-
5.4.3, Table 12(Tear Strength, ISO 20344 , 6.3 )	-	700	-
5.4.4, Table 13(Tensile properties ,ISO 20344 , 6.4.1 )	-	500	-
5.4.5, Table 14(Flexing resistance ,ISO 20344,6.5)	-	1000	-
5.4.6(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	1000	-
5.4.7(Ph Value ; ISO 20344,6.9)	-	500	-
5.4.9(Chromium VI content; ISO 17075)	-	500	-
5.5.1,Table 15(Tear Strength, ISO 20344 , 6.3)	-	500	-
5.5.2(Abrasion Resistance ;ISO 20344 , 6.12)	-	1000	-
5.5.3(Water vapour permeability and coefficient,ISO 20344,6.6 & 6.8)	-	1000	-
5.5.4(Ph Value ; ISO 20344,6.9)	-	500	-
5.5.5(Chromium VI content; ISO 17075)	-	500	-
5.6.1,Table 16(Tear Strength, ISO 20344 , 6.3)	-	1000	-
5.6.2(Ph Value ; ISO 20344,6.9)	-	500	-
5.6.3(Chromium VI content; ISO 17075)	-	500	-
5.7.1;Table 3(Thickness ; ISO 20344,7.1)	-	300	-
5.7.2(Ph Value ; ISO 20344,6.9)	-	500	-
5.7.3(Water Absorption and desorption ISO 20344,7.2 )	-	700	-
5.7.4.1(Insole ; ISO 20344,7.3 )	-	500	-
5.7.4.2(Insocks ; ISO 20344, 6.12)	-	1000	-
5.7.5(Chromium VI content; ISO 17075)	-	500	-
5.8.1(Design, IS 15298 Part 2 )	-	100	-
5.8.1.1, Table 17(Thickness ; ISO 20344, 8.1.2)	-	300	-
5.8.1.2(Cleated area ; ISO 20344 , Fig 38)	-	100	-
5.8.1.3, Table 17(Cleat height; ISO 20344, 8.1)	-	100	-
5.8.2(Tear Strength, ISO 20344 , 8.2)	-	1000	-
5.8.3(Abrasion Resistance ;ISO 20344 , 8.3)	-	1000	-
5.8.4(Flexing resistance ,ISO 20344,8.4)	-	1000	-
5.8.5(Hydrolysis ; ISO 20344,8.5)	-	1000	-
5.8.6(Interlayer bond strength; ISO 20344, 5.2)	-	1000	-
6.2.1.1.1(Metallic anti-penetration insert; ISO 20344, 5.8.2)	-	1000	-
6.2.1.1.2(Non-metallic anti-penetration insert; ISO 20344, 5.8.3)	-	1000	-
6.2.1.2(Consruction)	-	300	-
6.2.1.3(Dimension ; ISO 20344, 5.8.1)	-	100	-
6.2.1.4(Flex resistance of penetration -resistant insert ; ISO 20344,5.9)	-	1000	-
6.2.1.5.1(Corrosion resistance of penetration -resistant metallic insert - ISO 20344, 5.6.3 &5.6.1)	-	1000	-
6.2.1.5.2(Penetration -resistant non-metallic insert ; EN 12568,6.4&7.4)	-	1000	-
6.2.2.1 (Conductive footwear ; ISO 20344,5.10 & 5.10.3.3)	-	2000	-
6.2.2.2(Antistatic footwear ; ISO 20344,5.10)	-	2000	-
6.2.2.3(Electrically insulating footwear; EN 50321)	-	1000	-
6.2.3.1(Hear insulation of sole complex; ISO 20344,5.12 ;Annex B)	-	1000	-
6.2.3.2(Cold insulation of sole complex; ISO 20344,5.13)	-	1000	-
6.2.4(Energy absorption of seat region; ISO 20344,5.14)	-	1000	-
6.2.5(Water resistance ; 5.15.1 & 5.15.2)	-	1000	-
6.3(Upper--Water penetration and absorption ; ISO 20344 , 5.13)	-	1000	-
6.4.1(Resistance to hot contact ; ISO 20344 , 8.7)	-	1000	-
6.4.2(Resistance to fuel oil ; ISO 20344 , 8.6.1& 8.6.2 ; )	-	1000	-
5.3.2.2,Table 5(Internal length of toecaps , ISO 20344 , 5.3)	-	500	-
5.3.5.2,Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	800	-
5.3.5.3,Table 8(Slip resistance on steel floor with glycerin)	-	800	-
5.3.5.4(Slip resistance on ceramic tile floor with NaLS and on steel floor with glycerin)	-	800	-
5.4.2, Table 11(Thickness , ISO 20344 , 6.1 )	-	100	-
5.4.3, Table 12(Tear Strength, ISO 20344 , 6.3 )	-	1000	-
5.4.4, Table 13(Tensile properties ,ISO 20344 , 6.4.1 )	-	1000	-
5.5.1,Table 15(Tear Strength, ISO 20344 , 6.3)	-	1000	-
5.6.1,Table 16(Tear Strength, ISO 20344 , 6.3)	-	500	-
5.6.3(Chromium VI content; ISO 17075)	-	100	-
5.7.1;Table 3(Thickness ; ISO 20344,7.1)	-	100	-
5.7.3(Water Absorption and desorption ISO 20344,7.2 )	-	500	-
5.7.4.1(Insole ; ISO 20344,7.3 )	-	1000	-
5.8.1.1, Table 17(Thickness ; ISO 20344, 8.1.2)	-	100	-
6.2.1.1.1(Metallic anti-penetration insert; ISO 20344, 5.8.2)	-	100	-
6.2.1.1.2(Non-metallic anti-penetration insert; ISO 20344, 5.8.3)	-	100	-
6.2.1.2(Consruction)	-	100	-
6.2.1.3(Dimension ; ISO 20344, 5.8.1)	-	500	-
6.2.1.5.1(Corrosion resistance of penetration -resistant metallic insert - ISO 20344, 5.6.3 &5.6.1)	-	500	-
6.2.1.5.2(Penetration -resistant non-metallic insert ; EN 12568,6.4&7.4)	-	500	-
6.2.2.1 (Conductive footwear ; ISO 20344,5.10 & 5.10.3.3)	-	1000	-
6.2.2.2(Antistatic footwear ; ISO 20344,5.10)	-	1000	-
6.2.4(Energy absorption of seat region; ISO 20344,5.14)	-	500	-
6.2.5(Water resistance ; 5.15.1 & 5.15.2)	-	500	-
6.4.1(Resistance to hot contact ; ISO 20344 , 8.7)	-	500	-
5.3.6(Innocuousness)	-	25000	chemical test

26 Sep, 2027

-
-

IS 16221 : Part 1 (2016)

Safety of Power Converters for use in Photovoltaic Power Systems Part 1 General Requirements

1120000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
15(Software and firmware performing safety functions)	-	1000	-
14(Components)	-	5000	-
13(Physical requirements)	-	25000	-
12(Chemical hazards)	-	25000	-
11(Protection against liquid hazards)	-	25000	-
10(Protection against Sonic Pressure hazards)	-	25000	-
9(Protection Against Fire Hazards)	-	25000	-
8(Protection Against mechanical Hazards)	-	25000	-
7(Protection against electric shock and energy hazards)	-	50000	-
6(Environmental Requirements and conditions)	-	50000	-
5(Marking and documentation)	-	5000	-
4(General testing requirements)	-	5000	-
14(Components)	-	25000	-
6.4(UV exposure)	-	50000	-
13.6.4(UV Resistance)	-	50000	-
Annex J(Ultraviolet light conditioning test)	-	2000	-
9.1.4.3(Hot flaming oil test)	-	15000	-
4.2(Thermal testing)	-	35000	-
4.4(Testing in single fault condition)	-	25000	-
4.5(Humidity preconditioning)	-	35000	-
4.6(Backfeed voltage protection)	-	15000	-
4.7(Electrical rating tests)	-	15000	-
4.8(Additional tests for grid interactive inverters)	-	15000	-
Annex A(Measurement of clearances and creepage distances)	-	2000	-
Annex B(Programmable equipment)	-	0	-
Annex C(Symbols to be used in equipment markings)	-	1000	-
Annex D(Test probes for determining access)	-	1000	-
Annex E(RCDs)	-	5000	-
Annex F(Altitude correction for clearances)	-	2000	-
Annex G(Clearance and creepage distance determination for frequencies greater than 30 kHz)	-	2000	-
Annex H("Measuring instrument for touch current measurements ")	-	2000	-
4.4.4.10(Safety interlock systems)	-	4000	-
4.3, 4.3.2, 4.3.2.2, 4.3.2.3(Thermal Tests (Maximum temperatures, Touch temperature, temperature limits for mount surfaces))	-	25000	-
4.4.3.1(Protection against shock hazard)	-	25000	-
4.4.3.2(Protection against spread of fire)	-	15000	-
4.4.3.4(Protection Against parts expulsion hazards)	-	15000	-
4.4.4.1(Component fault tests)	-	35000	-
4.4.4.2(Equipment’s or parts for short-term or intermittent operation)	-	25000	-
4.4.4.3(Motors(Lock rotor))	-	2000	-
4.4.4.4(Transformer short circuit tests)	-	15000	-
4.4.4.5(Output short circuit)	-	15000	-
4.4.4.6(Backfeed current test for equipment with more than one source of supply)	-	15000	-
4.4.4.7(Output overload)	-	25000	-
4.4.4.8(Cooling system failure)	-	15000	-
4.4.4.9(Heating devices)	-	15000	-
4.4.4.11(Reverse d.c. connections)	-	15000	-
4.4.4.12(Voltage selector mismatch)	-	5000	-
4.4.4.13(Mis-wiring with incorrect phase sequence or polarity)	-	5000	-
4.4.4.14(Printed wiring board short-circuit test)	-	5000	-
4.6.1(Backfeed tests under normal conditions)	-	5000	-
4.6.2(Backfeed tests under single-fault conditions)	-	5000	-
5.1.2(Durability of markings)	-	5000	-
5.2.1(Visibility and legibility requirements for warning markings)	-	5000	-
6.3(Ingress protection)	-	15000	-
7.3.2.3(Short-term limits of accessible voltages under fault conditions)	-	15000	-
7.3.2.6(Working voltage and DVC)	-	15000	-
7.3.4,7.3.4.2(protection against direct contact)	-	15000	-
7.3.4.3(Protection by means of insulation of live parts)	-	15000	-
7.3.5,7.3.5.2(Protection in case of direct contact)	-	10000	-
7.3.5.3.1(Limitation of current through protective impedance)	-	10000	-
7.3.5.3.2(Limitation of discharging energy through protective impedance)	-	15000	-
7.3.5.4(Protection by means of limited voltages)	-	15000	-
7.3.6.1,7.3.6.2(Protection against indirect contact(Creapage & clearance))	-	5000	-
7.3.6.3(Protective class I - Protective bonding and earthing)	-	5000	-
7.3.6.3.3(Rating of protective bonding)	-	5000	-
7.3.7.8.4.2(Use of coating materials (on PWBs))	-	5000	-
7.3.7.4(Clearance distances)	-	5000	-
7.3.7.5(Creepage distances)	-	5000	-
7.3.8(Residual current detection (RCD) or Monitoring (RCM) device compatibilty (DC components on AC side))	-	5000	-
7.3.9(Protection against shock hazard due to stored energy)	-	5000	-
7.4(Protection against energy hazards)	-	5000	-
7.5.1(Impulse voltage test (type test))	-	5000	-
7.5.2(Voltage test (dielectric strength test))	-	5000	-
7.5.2.3(Humidity preconditioning)	-	5000	-
7.5.3(Partial discharge test (type test or sample test))	-	5000	-
7.5.4(Touch current measurement)	-	5000	-
7.3.7.5(Creepage distances)	-	5000	-
7.3.8(Residual current detection (RCD) or Monitoring (RCM) device compatibilty (DC components on AC side))	-	5000	-
7.3.9(Protection against shock hazard due to stored energy)	-	5000	-
7.5.2(Voltage test (dielectric strength test))	-	5000	-
7.5.2.3(Humidity preconditioning)	-	5000	-
7.5.3(Partial discharge test (type test or sample test))	-	5000	-
7.5.4(Touch current measurement)	-	5000	-
8.2(Moving parts)	-	1000	-
8.3(Stability)	-	2000	-
8.4(Provisions for lifting and carrying)	-	2000	-
8.5(Wall mounting)	-	2000	-
8.6(Expelled parts)	-	2000	-
9.1.1(Reducing the risk of ignition and spread of flame)	-	2000	-
9.1.2(Conditions for a fire enclosure)	-	2000	-
9.1.3(Material requirements for protection against fire hazard)	-	1000	-
9.1.4(Openings in fire enclosures)	-	1000	-
9.1.4.6(Additional requirements for openings in transportable equipment)	-	1000	-
9.2.2(Limited power source tests)	-	2000	-
9.3(Short-circuit and overcurrent protection)	-	1000	-
10.2(Sonic pressure and sound level)	-	1000	-
11.1(Liquid containment, pressure and leakage)	-	1000	-
11.2(Fluid pressure and leakage)	-	1000	-
13.1(Handles and manual controls)	-	1000	-
13.1.1(Adjustable controls)	-	1000	-
13.2(Securing of parts)	-	500	-
13.3(Provisions for external connections)	-	500	-
13.4(Internal wiring and connections)	-	500	-
13.5(Openings in enclosures)	-	500	-
13.3.2.5(Cord anchorages and strain relief)	-	500	-
13.3.5(Wire bending space for wires 10mm2 and greater)	-	500	-
13.5(Openings in enclosures)	-	500	-
13.6.2.1(Stress relief test)	-	500	-
13.7(Mechanical resistance to deflection, impact, or drop)	-	500	-
13.8(Thickness requirements for metal enclosures)	-	500	-
14.2(Motor over-temperature protection)	-	500	-
14.3(Over-temperature protection devices)	-	500	-
14.6(Printed circuit boards)	-	500	-
14.7(Circuits or components used as transient overvoltage limiting devices)	-	500	-

26 Sep, 2027

-
-

IS 6721 (1972)

Specification for PVC sandal

6050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.4(Dimension)	-	250	-
4.0(Lead Content )	-	500	-
4.0(Volatility % by mass)	-	800	-
4.0(Tear strength )	-	800	-
4.0(Elongation at break )	-	800	-
4.0(Tensile Strength )	-	800	-
4.0(Hardness (IRHD))	-	500	-
4.0(Density )	-	600	-
4.2(Design)	-	250	-
6(Marking)	-	250	-
"3.5(size and thickness of soles &heels)	-	500	-

26 Sep, 2027

-
-

IS 10702 (1992)

Rubber hawal chappal - Specification (Second Revision)

10400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4(Stud bolt)	-	250	-
5.4(Stud diameter)	-	250	-
5.4(Tear strength )	-	800	-
5.4(Hardness (shore A)- after ageing)	-	500	-
5.4(Hardness (Shore A))	-	500	-
5.4(Breaking strength )	-	800	-
5.4(Elongation at break )	-	800	-
5.4(Tensile Strength )	-	800	-
5.4(Relative density )	-	500	-
5.4(Shrinkage test (at 100 C temp))	-	800	-
5.4(Shrinkage test (at room temp))	-	800	-
5.4(Split tear strength )	-	800	-
5.4(Compression set)	-	1200	-
5.4(Hardness (Shore A))	-	500	-
5.4(Relative density)	-	600	-
5.3(Thickness )	-	250	-
5.1(Shape & Design)	-	250	-

26 Sep, 2027

-
-

IS 16221 : Part 2 (2015)

Safety of power converters for use in photovoltaic power systems: Part 2 particular requirements for inverters

1300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	2000	-
5(Marking and documentation)	-	3000	-
6(Environmental requirements and conditions)	-	35000	-
7(Protection against electric shock and energy hazards)	-	50000	-
8(Protection against Mechanical Hazards)	-	50000	-
9(Protection against Fire Hazards)	-	50000	-
10(Protection against Sonic Pressure Hazards)	-	50000	-
11(Protection against Liquid Hazards)	-	50000	-
12(Protection against Chemical Hazards)	-	50000	-
13(Physical Requirements)	-	50000	-
14(Components)	-	50000	-
14(Components)	-	50000	-
6.4(UV exposure)	-	35000	-
13.6.4(UV Resistance)	-	35000	-
Annex J(Ultraviolet light conditioning test)	-	25000	-
9.1.4.3(Hot flaming oil test)	-	50000	-
Clause No. 4.3(Thermal testing)	-	50000	-
Clause No. 4.4(Testing in single fault condition)	-	35000	-
4.5(Humidity preconditioning)	-	35000	-
4.7(Electrical rating tests)	-	50000	-
4.8(Additional tests for grid interactive inverters)	-	25000	-
4.4.4.15.1(Fault-tolerance of residual current monitoring)	-	25000	-
4.4.4.15.2(Fault-tolerance of automatic disconnecting means)	-	25000	-
4.4.4.16(Stand-alone inverters – Load transfer test)	-	35000	-
4.4.4.17(Cooling system failure – Blanketing test)	-	20000	-
4.7.3(Measurement requirements for AC output ports for stand-alone inverters)	-	20000	-
4.7.4(Stand-alone Inverter AC output voltage and frequency)	-	20000	-
4.7.4.2(Steady state output voltage at nominal DC input)	-	20000	-
4.7.4.3(Steady state output voltage across the DC input range)	-	20000	-
4.7.4.4(Load step response of the output voltage at nominal DC input)	-	20000	-
4.7.4.5(Steady state output frequency)	-	20000	-
4.7.5.2(Sinusoidal output voltage waveform requirements)	-	20000	-
4.7.5.3(Non-sinusoidal output waveform requirements)	-	20000	-
4.7.5.5(Output voltage waveform requirements for inverters for dedicated loads)	-	20000	-
4.8.2.1(Array insulation resistance detection for inverters for ungrounded arrays)	-	25000	-
4.8.2.2(Array insulation resistance detection for inverters for functionally grounded arrays)	-	25000	-
4.8.3.2(30 mA touch current type test for isolated inverters)	-	25000	-
4,8.3.3(Fire hazard residual current type test for isolated inverters)	-	25000	-
4.8.3.5(Protection by residual current monitoring)	-	20000	-
7.3.10(Additional requirements for stand-alone inverters)	-	20000	-
9.3.4(Inverter backfeed current onto the array)	-	20000	-
13.9(Fault indication)	-	20000	-
14(Components)	-	5000	-

26 Sep, 2027

-
-

IS/IEC 61730 : PART 1 (2004)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction

200000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Application classes)	-	20000	-
4(Construction requirements)	-	20000	-
5(Polymeric materials)	-	20000	-
6(Internal wiring and current-carrying parts)	-	20000	-
7(Connections)	-	30000	-
8(Bonding and grounding)	-	30000	-
9(Creepage and clearance distances)	-	20000	-
10(Field wiring compartments with covers)	-	20000	-
11(Marking)	-	10000	-
12()	-	10000	-

26 Sep, 2027

-
-

IS 14286 : Part 1 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements (Second Revision)

950000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and documentation)	-	150000	-
6(Testing)	-	150000	-
8(Major visual defects)	-	150000	-
9(Report)	-	150000	-
10(Modifications)	-	150000	-
11(Test flow and procedures)	-	200000	-

26 Sep, 2027

-
-

IS 14286 : Part 1 : Sec 4 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 4 special requirements for testing of thin - Film Cu(In,ga)(S,se)2 based photovoltaic (Pv) modules (Second Revision)

1000000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(Visual inspection (MQT 01))	-	3000	-
11.2(Maximum power determination (MQT 02))	-	25000	-
11.3(Insulation test (MQT 03))	-	20000	-
11.4(Measurement of temperature coefficients (MQT 04))	-	25000	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	25000	-
11.6(Performance at STC and NMOT (MQT 06))	-	70000	-
11.7(Performance at low irradiance (MQT 07))	-	25000	-
11.8(Outdoor exposure test (MQT 08))	-	25000	-
11.9(Hot-spot endurance test (MQT 09))	-	125000	-
11.1(UV preconditioning test (MQT 10))	-	70000	-
11.11(Thermal cycling test (MQT 11))	-	175000	-
11.12(Humidity-freeze test (MQT 12))	-	70000	-
11.13(Damp heat test (MQT 13))	-	150000	-
11.14(Robustness of terminations (MQT 14))	-	25000	-
11.15(Wet leakage current test (MQT 15))	-	25000	-
11.16(Static mechanical load test (MQT 16))	-	95000	-
11.17(Hail test (MQT 17))	-	25000	-
11.18(Bypass diode thermal test (MQT 18))	-	20000	-
11.19(Stabilization (MQT 19))	-	2000	-

26 Sep, 2027

-
-

IS 14286 : Part 1 : Sec 3 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 3 special requirements for testing of thin - Film amorphous silicon based photovoltaic (Pv) modules (Second Revision)

1122000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 IS 14286( Marking and Documentation)	-	2000	-
11.1 IS 14286( Visual inspection)	-	3000	-
11.2 IS 14286( Maximum power determination)	-	25000	-
11.3 IS 14286( Insulation Test)	-	20000	-
11.4 IS 14286( Measurement of temperature coefficients)	-	25000	-
11.5 IS 14286( Measurement of nominal module operating temperature (NMOT))	-	25000	-
11.6 IS 14286( Performance at STC and NMOT)	-	25000	-
11.7 IS 14286( Performance at low irradiance)	-	25000	-
11.8 IS 14286( Outdoor exposure Test)	-	25000	-
11.9 IS 14286( Hot-spot endurance test)	-	25000	-
11.10 IS 14286( UV Preconditioning test )	-	70000	-
11.11 IS 14286( Thermal cycling test)	-	175000	-
11.12 IS 14286( Humidity-freeze test)	-	70000	-
11.13 IS 14286(Damp heat test)	-	150000	-
11.14, Table 1 IS 14286( Robutness of terminations test - Retention of Junction Box on Mounting Surface - Test of Cord Anchorage)	-	25000	-
11.15 IS 14286( Wet leakage current test)	-	25000	-
11.16 IS 14286( Static Mechanical load test)	-	95000	-
11.17, Table 3 & 4, IS 14286( Hail test)	-	25000	-
11.18 IS 14286( Bypass diode testing)	-	20000	-
11.19 IS 14286( Stabilization )	-	2000	-
11.15(Wet leakage current test (MQT 15))	-	25000	-
11.16(Static mechanical load test (MQT 16))	-	50000	-
11.17(Hail test (MQT 17))	-	25000	-
11.18(Bypass diode thermal test (MQT 18))	-	20000	-
11.19(Stabilization (MQT 19))	-	2000	-

26 Sep, 2027

-
-

IS 14286 : Part 1 : Sec 2 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 2 special requirements for testing of thin - Film cadmium telluride (CdTe) based photovoltaic (Pv) modules (Second Revision)

810000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 IS 14286( Marking and Documentation)	-	2000	-
11.1 IS 14286( Visual inspection)	-	3000	-
11.2 IS 14286( Maximum power determination)	-	25000	-
11.3 IS 14286( Insulation Test)	-	20000	-
11.4 IS 14286( Measurement of temperature coefficients)	-	25000	-
11.5 IS 14286( Measurement of nominal module operating temperature (NMOT))	-	25000	-
11.6 IS 14286( Performance at STC and NMOT)	-	25000	-
11.7 IS 14286( Performance at low irradiance)	-	25000	-
11.8 IS 14286( Outdoor exposure Test)	-	25000	-
11.9 IS 14286( Hot-spot endurance test)	-	25000	-
11.10 IS 14286( UV Preconditioning test )	-	70000	-
11.11 IS 14286( Thermal cycling test)	-	175000	-
11.13 IS 14286(Damp heat test)	-	150000	-
11.14, Table 1 IS 14286( Robutness of terminations test - Retention of Junction Box on Mounting Surface - Test of Cord Anchorage)	-	25000	-
11.15 IS 14286( Wet leakage current test)	-	25000	-
11.16 IS 14286( Static Mechanical load test)	-	95000	-
11.17, Table 3 & 4, IS 14286( Hail test)	-	25000	-
11.18 IS 14286( Bypass diode testing)	-	20000	-
11.19 IS 14286( Stabilization )	-	2000	-
11.18(Bypass diode thermal test (MQT 18))	-	20000	-
11.19(Stabilization (MQT 19))	-	3000	-

26 Sep, 2027

-
-

IS 14286 : Part 1 : Sec 1 (2019)

Terrestrial photovoltaic (PV) modules - Design qualification and type approval: Part 1 test requirements: Sec 1 special requirements for testing of crystalline silicon photovoltaic (Pv) modules (Second Revision)

810000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.1(Visual inspection (MQT 01))	-	3000	-
11.2(Maximum power determination (MQT 02))	-	25000	-
11.3(Insulation test (MQT 03))	-	20000	-
11.4(Measurement of temperature coefficients (MQT 04))	-	25000	-
11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	25000	-
11.6(Performance at STC and NMOT (MQT 06))	-	25000	-
11.7(Performance at low irradiance (MQT 07))	-	25000	-
11.8(Outdoor exposure test (MQT 08))	-	25000	-
11.9(Hot-spot endurance test (MQT 09))	-	25000	-
11.1(UV preconditioning test (MQT 10))	-	70000	-
11.11(Thermal cycling test (MQT 11))	-	175000	-
11.12(Humidity-freeze test (MQT 12))	-	70000	-
11.13(Damp heat test (MQT 13))	-	150000	-
11.14(Robustness of terminations (MQT 14))	-	25000	-
11.15(Wet leakage current test (MQT 15))	-	25000	-
11.16(Static mechanical load test (MQT 16))	-	50000	-
11.17(Hail test (MQT 17))	-	25000	-
11.18(Bypass diode thermal test (MQT 18))	-	20000	-
11.19(Stabilization (MQT 19))	-	2000	-

26 Sep, 2027

-
-

IS 16169 (2019)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures (First Revision)

1000000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7(Documentation)	-	50000		-
6 to 6.2(Test for single or multi-phase inverter to Pass/fail criteria)	-	950000		-

26 Sep, 2027

-
-

IS 14286 (2010)

Crystalline silicon terrestrial photovoltaic (PV) modules - Design qualification and type approval (First Revision)

810000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Marking)	-	2000	-
10.1(Visual inspection)	-	3000	-
10.2(Maximum power determination)	-	25000	-
10.3(Insulation test)	-	20000	-
10.4(Measurement of temperature coefficients)	-	25000	-
10.5(Measurement of NOCT)	-	25000	-
10.6(Performance at STC and NOCT)	-	25000	-
10.7(Performance at low irradiance)	-	25000	-
10.8(Outdoor exposure test)	-	25000	-
10.9(Hot-spot endurance test)	-	25000	-
10.10(UV preconditioning)	-	70000	-
10.11(Thermal cycling test)	-	175000	-
10.12(Humidity freeze test)	-	70000	-
10.13(Damp heat test)	-	150000	-
10.14(Robustness of termination test)	-	25000	-
10.15(Wet leakage current test)	-	25000	-
10.16(Mechanical load test)	-	50000	-
10.17(Hail test)	-	25000	-
10.18(Bypass diode thermal' test)	-	20000	-

26 Sep, 2027

-
-

IS 10908 (1991)

Flexible rubber tubing for liquefied petroleum gas - Specification (First Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1 (The tubing made out of this material shall be green in colour )	-	100	-
Cl.4.2(The walls shall be seamless and free from all visible such as lumps, blows-holes,cracks etc and the bore shall be clean and free from loose particles which might be carried forward by the gas)	-	100	-
Cl4.3.1(The tubing shall be supplied in 6.4 and 7.0 mm inisde diametre,The tolerance on nominal diamtere shall be as per table 1)	-	400	-
Cl4.3.2(it shall comply with the thickness as givien in table 1 when measured according to 4.2.2 of IS 443;1975 The readings shall be taken from different sample sections.)	-	400	-
Cl.4.4,(Cl.4.4.1)(when tested in accordance with the method given in AnnexureA. It shall fit over the standard and oversize metal nozzle shown in Fig1,2 and 3)	-	800	-
Cl.4.4,(Cl.4.4.2)(it shall remain atatched to both nozzles throught the test period)	-	800	-
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the increase in the outside diametre of the tubing ,Also the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	800	-
Cl.4.5(When immersed in water for 5 minutes under an internal air pressure of 0.25 Mpa or 250kPa (2.5 bar), the same shall not burst when the pressure is increasded to 0.5 Mpa or 500 kpa (5 bar0, The test shall be carried out on a lengtj of 60 cm.)	-	800	-
Cl.4.6(Shore Hardness: the hardnesss on the flatsurface of the cut/slit tubing shall be measured and the same shall be 60 ± 5˚A)	-	800	-
Cl.4.7(Accelerated Ageing test, the flexible tubing or suitable portion of the tubing shall be subjected to accelerated ageing at a temperature of 100Deg Cfor 72 hours in accordance with the method prescribed in IS 3400 (Part 4) it shall not show a change of + 10 A of its orignal shore hardness )	-	1500	-
Cl.4.8.1(Flexible test , Annexure B The gas pressure shown on the manometre shall not drop by more than 1 Kpa)	-	800	-
Cl4.8.2(The tubing shall be so flexible that it will make contact with a cylinder former of radius 68 mm for at least 110 deg of its circumference when the tubing is placed over the framer and a mass of 1.6 kg is attcahed to each end)	-	800	-
Cl.4.9(Crushing test , )	-	1000	-
Cl.4.10(Resistance to lpg ,Annexure c Shall not be more than 15 % of the initial mass of the tubing and the amount of exctractable matter shall not excced 10 percent of the iniital mass of te tubing)	-	900	-
Cl.4.11(Resistance to Ozone ,Annexure D Shall not show any breakage on surface or crack or defects)	-	2000	-
Cl.4.12(Burning behaviour on exposure to small flame,Annexure E tubing shall not burn to either of the outer marks within the test period of 45 seconds)	-	1000	-

26 Sep, 2027

-
-

IS 13395 (2021)

Performance of Handles and Handle Assemblies Attached to Cookware - Specification ( First Revision )

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Construction)	-	200	-
4.2(Materials)	-	200	-
4.3(Selection and Size)	-	200	-
4.4(Position of handle and knob with respect to cookware)	-	200	-
4.5(Attachment to cookware)	-	200	-
4.()	-	200	-
4.()	-	200	-
5.1(General)	-	400	-
5.2(Bending strength)	-	800	-
5.3(Torque strength)	-	800	-
5.4(Impact strength)	-	800	-
5.5(Fatigue resistance)	-	3000	-
5.6(Leakage)	-	2000	-
5.7(Thermal insulation)	-	1000	-
5.8(Heat resistance)	-	800	-
5.9(Washing resistance)	-	900	-
5.10(Burning resistance)	-	900	-

26 Sep, 2027

-
-

IS 6911 (2017)

Stainless steel plate, sheet and strip - Specification (Second Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Freedom from defects , IS 6911)	-	100	-
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Molybdenum -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Niobium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Titanium-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.1 & 7.2 Table 1(Others-IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
10.1 - 4(Tensile Test)	-	800	-
10.1 - 4(Yield strength)	-	800	-
10.1 Amd 2(0.2 Percent Proof Stress)	-	1000	-
10.1 - 4(Elongation % on 50mm)	-	700	-
10.2(Hardness Test)	-	800	-
10.3(Bend Test)	-	700	-
11(Erichsen Cupping Test)	-	700	-
17(Dimension and tolerance)	-	300	-
12(Corrosion resistance)	-	500	-

26 Sep, 2027

-
-

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Workmanship)	-	100	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Titanium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Vanadium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Boron)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Aluminium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Carbon)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Chromium)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Copper)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Manganese)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Molybdenum)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nickel)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Nitrogen)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Phosphorous)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Silicon)	-	300	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1)(Sulphor)	-	300	-
Cl 9.1 & Table 3(Diameter & Out Of Round)	-	300	-
Cl 10(UTM)	-	2000	-
10.3(Torsion test- IS 1717)	-	1000	-
10.4(Wrapping test-IS 1755)	-	1000	-
15(Corrosion Resistance - IS:10461)	-	800	-

26 Sep, 2027

-
-

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl . 6 .0(Freedom from defect)	-	100	-
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	2002	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
8.2, Table 3(Tensile Test-1608:Part 1)	-	2000	-
8.2, Table 3(Proof Stress, N/mm2)	-	1500	-
8.2, Table 3(Tensile Strength, N/mm2)	-	1000	-
8.2, Table 3(Elongation, %)	-	800	-
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	800	-
8.4(Bend Test)	-	500	-
8.5(Erichsen Cupping Test)	-	700	-
10.1(Thickness, mm)	-	200	-
10.2(width, mm)	-	200	-
10.3(Length, mm)	-	200	-
10.4(Flatness,mm)	-	200	-
10.5(Camber, mm)	-	200	-
11(Surface Finish)	-	100	-

26 Sep, 2027

-
-

IS 740 (1977)

Specification for wrought aluminium and aluminium alloy rivet stock for general engineering purposes (Second Revision)

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1, Table 1of IS:740 (Designation 65032)(Aluminium)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Aluminium)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Aluminium)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Aluminium)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Aluminium)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Aluminium)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Either Cr or Mn shall present)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Titanium and or other grain refining elements)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Cr+Mn)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Titanium and or other grain refining elements)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Cr+Mn)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Titanium and or other grain refining elements)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Cr+Mn)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Titanium and or other grain refining elements)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Titanium and or other grain refining elements)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Cu+Mg+Si+Fe+Mn+Zn)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Chromium)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Copper)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Iron)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Magnesium)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Manganese)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Silicon)	-	600	-
4.1, Table 1of IS:740 (Designation 65032)(Zinc)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Chromium)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Chromium)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Chromium)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Chromium)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Copper)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Copper)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Copper)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Copper)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Copper)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Iron)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Iron)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Iron)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Iron)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Iron)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Magnesium)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Magnesium)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Magnesium)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Magnesium)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Magnesium)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Manganese)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Manganese)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Manganese)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Manganese)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Manganese)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Silicon)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Silicon)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Silicon)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Silicon)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Silicon)	-	600	-
4.1, Table 1of IS:740 (Designation 64430)(Zinc)	-	600	-
4.1, Table 1of IS:740 (Designation 55000)(Zinc)	-	600	-
4.1, Table 1of IS:740 (Designation 53000)(Zinc)	-	600	-
4.1, Table 1of IS:740 (Designation 24345)(Zinc)	-	600	-
4.1, Table 1of IS:740 (Designation 19000)(Zinc)	-	600	-
4.1, Table 1of IS:740 (Designation & Condition 65032, 'W')(Tensile Strength of Size upto and including 25 mm)	-	2000	-
4.1, Table 1of IS:740 (Designation & Condition 64430, 'W')(Tensile Strength of Size upto and including 25 mm)	-	2000	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	2000	-
4.1, Table 1of IS:740 (Designation & Condition 55000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	2000	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'OD')(Tensile Strength of Size upto and including 25 mm)	-	2000	-
4.1, Table 1of IS:740 (Designation & Condition 53000, 'O or M')(Tensile Strength of Size upto and including 25 mm)	-	2000	-
4.1, Table 1of IS:740 (Designation & Condition 24345, 'W')(Tensile Strength of Size upto and including 12 mm)	-	2000	-
4.1, Table 1of IS:740 (Designation & Condition 19000, '112')(Tensile Strength of Size upto and including 12 mm)	-	2000	-
6(Freedom From Defects)	-	500	-
7(Dmension And Tolerances)	-	500	-
9.2(Head Forming Test)	-	1500	-
11(Marking)	-	200	-

26 Sep, 2027

-
-

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

A-29, Sector 5, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

9205030060 testing.a29@urs-labs.com

Scope List