BIS - LIMS (Laboratory Information Management System)

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

A-29, Sector 5, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

9871062220 testing.a29@urs-labs.com

Scope List

Reset

154 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 17980 (2022)

Maximum Power Point Tracking Efficiency of Grid Connected Photovoltaic Inverters (First Revision)

523000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl-4.1 (a)(Static MPPT efficiency)	-	249000		-
Cl-4.1 (b)(Dynamic MPPT efficiency)	-	274000		-

-
Included w.e.f 07.04.2025

122

IS/IEC 61683 (1999)

Photovoltaic systems - Power conditioners - Procedure for measuring efficiency

114000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Efficiency measurement conditions)	-	28500	5% discount for BIS
4.1(DC power source for testing)	-	0	-
4.2(Temperature)	-	0	n/a
4.3(Output voltage and frequency)	-	0	-
4.4(Input voltage)	-	0	-
4.5(Ripple and distortion)	-	0	-
4.6(Resistive loads/utility grid)	-	0	-
4.7(Reactive loads)	-	0	-
4.8(Resistive plus non-linear loads)	-	0	-
4.9(Complex loads)	-	0	-
5(Efficiency calculations)	-	28500	5% discount for BIS
6(Efficiency test circuits)	-	28500	5% discount for BIS
7(Loss measurement)	-	28500	5% discount for BIS
Annex A(Power conditioner description)	-	0	-
Annex B(Power efficiency and conversion factor)	-	0	-
Annex C(Weighted average energy efficiency)	-	0	-
Annex D(Derivation of efficiency tolerance in Table 2)	-	0	-
4(Efficiency measurement conditions)	-	0	-
4.1(DC power source for testing)	-	0	-
4.2(Temperature)	-	0	-
4.3(Output voltage and frequency)	-	0	-
4.4(Input voltage)	-	0	-
4.5(Ripple and distortion)	-	0	-
4.6(Resistive loads/utility grid)	-	0	-
4.7(Reactive loads)	-	0	-
4.8(Resistive plus non-linear loads)	-	0	-
4.9(Complex loads)	-	0	-
5(Efficiency calculations)	-	0	-
6(Efficiency test circuits)	-	0	-
7(Loss measurement)	-	0	-
Annex A(Power conditioner description)	-	0	-
Annex B(Power efficiency and conversion factor)	-	0	-
Annex C(Weighted average energy efficiency)	-	0	-
Annex D(Derivation of efficiency tolerance in Table 2)	-	0	-

-
Included w.e.f 07.04.2025

123

IS 14286 : Part 1 : Sec 1 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-1: Special requirements for testing of crystalline silicon photovoltaic PV modules Third Revision

1450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	10000	-
Cl-11.1(Visual inspection)	-	10000	-
Cl-11.2(Maximum power determination)	-	200000	-
Cl-11.3(Insulation test)	-	200000	-
Cl-11.4(Measurement of temperature coefficients)	-	200000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	10000	-
Cl-11.6(Performance at STC)	-	200000	-
Cl-11.7(Performance at low irradiance)	-	100000	-
Cl-11.8(Outdoor exposure test)	-	100000	-
Cl-11.9(Hot-spot endurance test)	-	100000	-
Cl-11.10(UV preconditioning test)	-	100000	-
Cl-11.11(Thermal cycling test)	-	200000	-
Cl-11.12(Humidity-freeze test)	-	200000	-
Cl-11.13(Damp heat test)	-	100000	-
Cl-11.14(Robustness of terminations test)	-	100000	-
Cl-11.15(Wet leakage current tes)	-	100000	-
Cl-11.16(Static mechanical load test)	-	100000	-
Cl-11.17(Hail test)	-	100000	-
Cl-11.18(Bypass diode thermal test)	-	100000	-
Cl-11.19(Stabilization)	-	100000	-
5(Marking and documentation)	-	100000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	100000	-
11.21(Potential induced degradation test (MQT 21))	-	100000	-
11.22(Bending test (MQT 22))	-	100000	-

-
Included w.e.f 04.03.2025

124

IS 15298 : part 4 (2024)

Personal Protective Equipment Part 4 Occupational Footwear (ISO 20347 : 2021, MOD) (Third Revision)

Personal Protective Equipment Part 4 Occupational Footwear

38500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	100	-
Cl 5.2.2(" Height of upper ")	-	250	-
Cl 5.2.3(Heel area)	-	500	-
Cl 5.3.1.1(Construction of whole footwear)	-	500	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	600	-
Cl 5.3.2(Leak proofness)	-	600	-
Cl 5.3.3(Specific ergonomic features)	-	600	-
Cl 5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1000	-
Cl 5.3.5, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	1000	-
Cl 5.3.5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	2500	-
Cl 5.3.5, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (x)(pH)	-	500	-
Cl 5.3.5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	2500	-
Cl 5.3.5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	2500	-
Cl 5.3.6(Seam strength)	-	600	-
Cl 5.3.7(Lead Content ( National Annex A))	-	600	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.2(Thickness)	-	250	-
Cl 5.4.3(Tear strength)	-	600	-
Cl 5.4.4, Table 9(Tensile properties- Tensile strength)	-	600	-
Cl 5.4.4, Table 9(Tensile properties- Breaking Force)	-	600	-
Cl 5.4.4, Table 9(Tensile properties-Modulus at 100 % elongation)	-	600	-
Cl 5.4.4, Table 9(Tensile properties- Elongation at break)	-	600	-
Cl 5.4.5(Flexing resistance)	-	800	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	800	-
Cl 5.4.7(Resistance to hydrolysis)	-	1000	-
Cl 5.5.2(Lining- Tear strength)	-	600	-
Cl 5.5.3(Lining- Abrasion resistance)	-	800	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	800	-
Cl 5.6.2(Tear strength of tongue)	-	600	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	250	-
Cl 5.7.2(Water permeability of insock)	-	800	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	800	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	800	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	800	-
Cl 5.8.2.1(Thickness of Outsole)	-	250	-
Cl 5.8.2.2(Cleated area)	-	250	-
Cl 5.8.2.3(Cleat height)	-	250	-
Cl 5.8.3(Outsole- Tear strength)	-	600	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	800	-
Cl 5.8.5(Outsole-Flexing resistance)	-	600	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	1000	-
Cl 5.8.7(Interlayer bond strength)	-	600	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	600	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	600	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	600	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	600	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	600	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	800	-
Cl 6.2.1.4.2.1(ISO 20344:2021, 5.11.2)	-	600	-
Cl 6.2.1.4.2.2(ISO 20344:2021, 5.6.2.1)	-	600	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	1000	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	2500	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	2500	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1000	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1000	-
Cl 6.2.4(Energy absorption of seat region)	-	1000	-
Cl 6.2.5(Water resistance)	-	1000	-
Cl 6.2.7.1(Cut resistance footwear- design)	-	1500	-
Cl 6.2.7.2(Dimensions and construction of protective area of Cut resistance footwear)	-	600	-
Cl 6.2.7.3(Resistance to cutting)	-	1500	-
Cl 6.2.8(Scuff cap)	-	800	-
Cl 6.2.9("Slip resistance on ceramic tile floor with glycerine ")	-	1000	-
Cl 6.3(Upper — Water penetration and absorption)	-	1000	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	800	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1000	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	800	-
Cl 6.4.3.2(Design of Ladder grip)	-	600	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	600	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	600	-
Cl 7("Marking ")	-	100	-

-
Included w.e.f. 17.02.2025 Exclusion: Cl 6.2.6 (Ankle protection)

125

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

Personal Protective Equipment Part 3 Protective Footwear

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	100	-
Cl 5.2.2(" Height of upper ")	-	250	-
Cl 5.2.3(Heel area)	-	500	-
Cl 5.3.1.1(Construction of whole footwear)	-	500	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	600	-
Cl 5.3.2.1(Toe protection - general)	-	600	-
Cl 5.3.2.2(Internal length)	-	600	-
Cl 5.3.2.3(Width of toecap flange)	-	600	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	600	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	600	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	600	-
Cl 5.3.2.6(Impact resistance)	-	1000	-
Cl 5.3.2.7(Compression resistance)	-	1000	-
Cl 5.3.3(Leak proofness)	-	800	-
Cl 5.3.4("Specific ergonomic features ")	-	600	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	1200	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	2500	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1200	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	600	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	2500	-
Cl 5.3.7(Seam strength)	-	600	-
Cl 5.3.8(Lead Content ( National Annex A))	-	1000	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.2(Thickness)	-	250	-
Cl 5.4.3(Tear strength)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	600	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	600	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	800	-
Cl 5.4.7(Resistance to hydrolysis)	-	1000	-
Cl 5.5.2(Lining- Tear strength)	-	600	-
Cl 5.5.3(Lining- Abrasion resistance)	-	800	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	800	-
Cl 5.6.2(Tear strength of tongue)	-	600	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	600	-
Cl 5.7.2(Water permeability of insock)	-	800	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	800	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	800	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	800	-
Cl 5.8.2.1(Thickness of Outsole)	-	600	-
Cl 5.8.2.2(Cleated area)	-	600	-
Cl 5.8.2.3(Cleat height)	-	600	-
Cl 5.8.3(Outsole- Tear strength)	-	600	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	800	-
Cl 5.8.5(Outsole-Flexing resistance)	-	800	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	1000	-
Cl 5.8.7(Interlayer bond strength)	-	600	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	600	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	600	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	600	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	600	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	600	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	800	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	600	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	600	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	1000	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	2500	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	2500	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1000	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1000	-
Cl 6.2.4(Energy absorption of seat region)	-	1000	-
Cl 6.2.5(Water resistance)	-	1000	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	1500	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	600	-
Cl 6.2.8.3(Resistance to cutting)	-	1500	-
Cl 6.2.9(Scuff cap)	-	800	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	1000	-
Cl 6.3(Upper — Water penetration and absorption)	-	800	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	1000	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1000	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	800	-
Cl 6.4.3.2(Design of Ladder grip)	-	800	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	800	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	800	-
Cl 7("Marking ")	-	100	-
Cl 7("Marking ")	-	100	-

-
Included w.e.f. 17.02.2025 Exclusion: Cl 6.2.6.1 (Metatarsal protection - Construction), Cl 6.2.6.2 ("Metatarsal protection-Impact resistance of metatarsal protective device "), Cl 6.2.7 (Ankle protection)

126

IS 15298 : Part 2 (2024)

Personal Protective Equipment Part 2 Safety Footwear (ISO 20345 : 2021, MOD) (Third Revision)

Personal Protective Equipment Part 2 Safety Footwear

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	100	-
Cl 5.2.2, Table 4(" Height of upper ")	-	150	-
Cl 5.2.3(Heel area)	-	100	-
Cl 5.3.1.1(Construction of whole footwear)	-	100	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	600	-
Cl 5.3.2.1(Toe protection - general)	-	100	-
Cl 5.3.2.2(Internal length)	-	250	-
Cl 5.3.2.3(Width of toecap flange)	-	100	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	600	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	600	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	600	-
Cl 5.3.2.6(Impact resistance)	-	1000	-
Cl 5.3.2.7(Compression resistance)	-	1000	-
Cl 5.3.3(Leak proofness)	-	1000	-
Cl 5.3.4("Specific ergonomic features ")	-	1000	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	1800	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1500	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	1500	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	2000	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	350	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	2500	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	3500	-
Cl 5.3.7(Seam strength)	-	600	-
Cl 5.3.8(Lead Content ( National Annex A))	-	600	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	600	-
Cl 5.4.2(Thickness)	-	600	-
Cl 5.4.3(Tear strength)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	600	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	600	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	600	-
Cl 5.4.5(Flexing resistance)	-	600	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	600	-
Cl 5.4.7(Resistance to hydrolysis)	-	1200	-
Cl 5.5.2(Lining- Tear strength)	-	600	-
Cl 5.5.3(Lining- Abrasion resistance)	-	800	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	800	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	600	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	600	-
Cl 5.7.2(Water permeability of insock)	-	800	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	800	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	800	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	800	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	500	-
Cl 5.8.2.2(Cleated area)	-	500	-
Cl 5.8.2.3(Cleat height)	-	500	-
Cl 5.8.3(Outsole- Tear strength)	-	600	-
Cl 5.8.5(Outsole-Flexing resistance)	-	600	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	2500	-
Cl 5.8.7(Interlayer bond strength)	-	600	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	600	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	600	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	600	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	500	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	500	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	600	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	500	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	500	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	1500	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	2500	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	2500	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1000	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1000	-
Cl 6.2.4(Energy absorption of seat region)	-	1000	-
Cl 6.2.5(Water resistance)	-	1000	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	1000	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	500	-
Cl 6.2.8.3(Resistance to cutting)	-	1000	-
Cl 6.2.9(Scuff cap)	-	1000	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	1000	-
Cl 6.3(Upper — Water penetration and absorption)	-	1000	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	800	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1000	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	1000	-
Cl 6.4.3.2(Design of Ladder grip)	-	500	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	500	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	500	-
Cl 7, Table 20("Marking ")	-	100	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	800	-
Cl 5.2(Design)	-	0	-
Cl 5.2.2, Table 4(" Height of upper ")	-	0	-
Cl 5.2.3(Heel area)	-	0	-
Cl 5.3.1.1(Construction of whole footwear)	-	0	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	0	-
Cl 5.3.2.1(Toe protection - general)	-	0	-
Cl 5.3.2.2(Internal length)	-	0	-
Cl 5.3.2.3(Width of toecap flange)	-	0	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	0	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	0	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	0	-
Cl 5.3.2.6(Impact resistance)	-	0	-
Cl 5.3.2.7(Compression resistance)	-	0	-
Cl 5.3.3(Leak proofness)	-	0	-
Cl 5.3.4("Specific ergonomic features ")	-	0	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	0	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	0	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	0	-
Cl 5.3.7(Seam strength)	-	0	-
Cl 5.3.8(Lead Content ( National Annex A))	-	0	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	0	-
Cl 5.4.2(Thickness)	-	0	-
Cl 5.4.3(Tear strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	0	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	0	-
Cl 5.4.5(Flexing resistance)	-	0	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	0	-
Cl 5.4.7(Resistance to hydrolysis)	-	0	-
Cl 5.5.2(Lining- Tear strength)	-	0	-
Cl 5.5.3(Lining- Abrasion resistance)	-	0	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	0	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	0	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	0	-
Cl 5.7.2(Water permeability of insock)	-	0	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	0	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	0	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	0	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	0	-
Cl 5.8.2.2(Cleated area)	-	0	-
Cl 5.8.2.3(Cleat height)	-	0	-
Cl 5.8.3(Outsole- Tear strength)	-	0	-
Cl 5.8.5(Outsole-Flexing resistance)	-	0	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	0	-
Cl 5.8.7(Interlayer bond strength)	-	0	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	0	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	0	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	0	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	0	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	0	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	0	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	0	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	0	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	0	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	0	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	0	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	0	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	0	-
Cl 6.2.4(Energy absorption of seat region)	-	0	-
Cl 6.2.5(Water resistance)	-	0	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	0	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	0	-
Cl 6.2.8.3(Resistance to cutting)	-	0	-
Cl 6.2.9(Scuff cap)	-	0	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	0	-
Cl 6.3(Upper — Water penetration and absorption)	-	0	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	0	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	0	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	0	-
Cl 6.4.3.2(Design of Ladder grip)	-	0	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	0	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	0	-
Cl 7, Table 20("Marking ")	-	0	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	0	-

-
Included w.e.f. 17.02.2025 Exclusion: Cl 6.2.6.2 ("Metatarsal protection-Impact resistance of metatarsal protective device "), Cl 6.2.7 (Ankle protection), Cl 6.2.6.1 (Metatarsal protection - Construction)

127

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	300	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	300	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	300	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	300	-
Cl-4.1(Main body of utensil)	-	300	-
Cl-4.1(Cast cookware)	-	300	-
Cl-4.1(Other aluminum components and parts)	-	300	-
Cl-4.1.1(Lids (material))	-	300	-
Cl-4.1.1(Minimum thickness of lid)	-	300	-
Cl-4.1.2(Minimum thickness of glass)	-	300	-
Cl-4.1.2(Material of rim)	-	300	-
Cl-4.1.2(Minimum thickness of rim)	-	300	-
Cl-4.2(Material of strips)	-	300	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Rivets used in lunch box)	-	300	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	300	-
Cl-4.5(Rivets for fixing of handles)	-	300	-
Cl-4.5(Material of cap)	-	300	-
Cl-4.6(Strips used for flame guards)	-	300	-
Cl-4.6(stainless steel)	-	300	-
Cl-5(Fabrication)	-	300	-
Cl-6(Shape and Dimensions)	-	300	-
Cl-7.1(Handles, when fitted)	-	300	-
Cl-7.2(Handles)	-	300	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	300	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	300	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	300	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	300	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	300	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	300	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	300	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	300	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	300	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	300	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	300	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	300	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	300	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	300	-
Cl-8(Workmanship and Finish)	-	300	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	300	-
Cl-8.3(Minimum nominal thickness)	-	300	-
Cl-8.3(Thickness of hard anodized)	-	300	-
Cl-8.3(Finish and appearance of hard anodized)	-	300	-
Cl-8.3(Abrasion resistance of hard anodized)	-	100	-
Cl-8.3(Colour of hard anodized)	-	100	-
Cl-8.3(Hardness of hard anodized)	-	100	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	100	-
Cl-8.5(Non-stick unreinforced PTFE)	-	100	-
Cl-8.6(Ceramic coating)	-	100	-
Cl-8.7(The thickness test, adhesion test)	-	100	-
Cl-8.7(Minimum thickness of coating)	-	100	-
Cl-8.7.1(Dry heat the cookware)	-	100	-
Cl-8.8(Requirements of PTFE)	-	100	-
Cl-8.9(Material for induction plate)	-	100	-
Cl-8.9(Test for Induction compatible base)	-	100	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	100	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	100	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	100	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	100	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	100	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	100	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	100	-
Cl-9.1(Normal Capacity)	-	100	-
Cl-9.2(Normal Capacity of internal diameter)	-	100	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	300	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	300	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	300	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	300	-
Cl-4.1(Main body of utensil)	-	300	-
Cl-4.1(Cast cookware)	-	300	-
Cl-4.1(Other aluminum components and parts)	-	300	-
Cl-4.1.1(Lids (material))	-	300	-
Cl-4.1.1(Minimum thickness of lid)	-	300	-
Cl-4.1.2(Minimum thickness of glass)	-	300	-
Cl-4.1.2(Material of rim)	-	300	-
Cl-4.1.2(Minimum thickness of rim)	-	300	-
Cl-4.2(Material of strips)	-	300	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Rivets used in lunch box)	-	300	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	300	-
Cl-4.5(Rivets for fixing of handles)	-	300	-
Cl-4.5(Material of cap)	-	300	-
Cl-4.6(Strips used for flame guards)	-	300	-
Cl-4.6(stainless steel)	-	300	-
Cl-5(Fabrication)	-	300	-
Cl-6(Shape and Dimensions)	-	300	-
Cl-7.1(Handles, when fitted)	-	300	-
Cl-7.2(Handles)	-	300	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	300	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	300	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	300	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	300	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	300	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	300	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	300	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	300	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	300	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	300	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	300	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	300	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	300	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	300	-
Cl-8(Workmanship and Finish)	-	300	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	300	-
Cl-8.3(Minimum nominal thickness)	-	300	-
Cl-8.3(Thickness of hard anodized)	-	300	-
Cl-8.3(Finish and appearance of hard anodized)	-	300	-
Cl-8.3(Abrasion resistance of hard anodized)	-	300	-
Cl-8.3(Colour of hard anodized)	-	300	-
Cl-8.3(Hardness of hard anodized)	-	300	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	300	-
Cl-8.5(Non-stick unreinforced PTFE)	-	300	-
Cl-8.6(Ceramic coating)	-	300	-
Cl-8.7(The thickness test, adhesion test)	-	300	-
Cl-8.7(Minimum thickness of coating)	-	300	-
Cl-8.7.1(Dry heat the cookware)	-	300	-
Cl-8.8(Requirements of PTFE)	-	300	-
Cl-8.9(Material for induction plate)	-	300	-
Cl-8.9(Test for Induction compatible base)	-	300	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	300	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	300	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	300	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	300	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	300	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	300	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	300	-
Cl-9.1(Normal Capacity)	-	300	-
Cl-9.2(Normal Capacity of internal diameter)	-	300	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	300	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	300	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	300	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	300	-
Cl-4.1(Main body of utensil)	-	300	-
Cl-4.1(Cast cookware)	-	300	-
Cl-4.1(Other aluminum components and parts)	-	300	-
Cl-4.1.1(Lids (material))	-	300	-
Cl-4.1.1(Minimum thickness of lid)	-	300	-
Cl-4.1.2(Minimum thickness of glass)	-	300	-
Cl-4.1.2(Material of rim)	-	300	-
Cl-4.1.2(Minimum thickness of rim)	-	300	-
Cl-4.2(Material of strips)	-	300	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Rivets used in lunch box)	-	300	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	300	-
Cl-4.5(Rivets for fixing of handles)	-	300	-
Cl-4.5(Material of cap)	-	300	-
Cl-4.6(Strips used for flame guards)	-	300	-
Cl-4.6(stainless steel)	-	300	-
Cl-5(Fabrication)	-	300	-
Cl-6(Shape and Dimensions)	-	300	-
Cl-7.1(Handles, when fitted)	-	300	-
Cl-7.2(Handles)	-	300	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	300	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	300	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	300	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	300	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	300	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	300	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	300	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	300	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	300	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	300	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	300	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	300	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	300	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	300	-
Cl-8(Workmanship and Finish)	-	300	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	300	-
Cl-8.3(Minimum nominal thickness)	-	300	-
Cl-8.3(Thickness of hard anodized)	-	300	-
Cl-8.3(Finish and appearance of hard anodized)	-	300	-
Cl-8.3(Abrasion resistance of hard anodized)	-	300	-
Cl-8.3(Colour of hard anodized)	-	300	-
Cl-8.3(Hardness of hard anodized)	-	300	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	300	-
Cl-8.5(Non-stick unreinforced PTFE)	-	300	-
Cl-8.6(Ceramic coating)	-	300	-
Cl-8.7(The thickness test, adhesion test)	-	300	-
Cl-8.7(Minimum thickness of coating)	-	300	-
Cl-8.7.1(Dry heat the cookware)	-	300	-
Cl-8.8(Requirements of PTFE)	-	300	-
Cl-8.9(Material for induction plate)	-	300	-
Cl-8.9(Test for Induction compatible base)	-	300	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	300	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	300	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	300	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	300	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	300	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	300	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	300	-
Cl-9.1(Normal Capacity)	-	300	-
Cl-9.2(Normal Capacity of internal diameter)	-	300	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	300	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	300	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	300	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	300	-
Cl-4.1(Main body of utensil)	-	300	-
Cl-4.1(Cast cookware)	-	300	-
Cl-4.1(Other aluminum components and parts)	-	300	-
Cl-4.1.1(Lids (material))	-	300	-
Cl-4.1.1(Minimum thickness of lid)	-	300	-
Cl-4.1.2(Minimum thickness of glass)	-	300	-
Cl-4.1.2(Material of rim)	-	300	-
Cl-4.1.2(Minimum thickness of rim)	-	300	-
Cl-4.2(Material of strips)	-	300	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Clips of lunch box)	-	300	-
Cl-4.3(Rivets used in lunch box)	-	300	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	300	-
Cl-4.5(Rivets for fixing of handles)	-	300	-
Cl-4.5(Material of cap)	-	300	-
Cl-4.6(Strips used for flame guards)	-	300	-
Cl-4.6(stainless steel)	-	300	-
Cl-5(Fabrication)	-	300	-
Cl-6(Shape and Dimensions)	-	300	-
Cl-7.1(Handles, when fitted)	-	300	-
Cl-7.2(Handles)	-	300	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	300	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	300	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	300	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	300	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	300	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	300	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	300	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	300	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	300	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	300	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	300	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	300	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	300	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	300	-
Cl-8(Workmanship and Finish)	-	300	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	300	-
Cl-8.3(Minimum nominal thickness)	-	300	-
Cl-8.3(Thickness of hard anodized)	-	300	-
Cl-8.3(Finish and appearance of hard anodized)	-	300	-
Cl-8.3(Abrasion resistance of hard anodized)	-	300	-
Cl-8.3(Colour of hard anodized)	-	300	-
Cl-8.3(Hardness of hard anodized)	-	300	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	300	-
Cl-8.5(Non-stick unreinforced PTFE)	-	300	-
Cl-8.6(Ceramic coating)	-	300	-
Cl-8.7(The thickness test, adhesion test)	-	300	-
Cl-8.7(Minimum thickness of coating)	-	300	-
Cl-8.7.1(Dry heat the cookware)	-	300	-
Cl-8.8(Requirements of PTFE)	-	300	-
Cl-8.9(Material for induction plate)	-	300	-
Cl-8.9(Test for Induction compatible base)	-	300	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	300	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	300	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	300	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	300	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	300	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	300	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	300	-
Cl-9.1(Normal Capacity)	-	300	-
Cl-9.2(Normal Capacity of internal diameter)	-	300	-

-
Included w.e.f.28.07.2025

128

IS 10322 : Part 5 : Sec 9 (2017)

Luminaires: Part 5 particular requirements: Sec 9 rope lights

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
21.4(General Test Requireements)	-	3000	-
21.5(Classification of Luminaires')	-	4000	-
21.6(Marking)	-	4000	-
21.7(Construction)	-	6000	-
21.8(Creepage Distance and Clearances)	-	4000	-
21.9(Provision for earthing)	-	4000	-
21.10(Terminals)	-	4000	-
21.11(External & Internal Wiring)	-	6000	-
21.12(Protection against electric shock)	-	4000	-
21.13(Endurance Tests and Thermal Tests)	-	8000	-
21.14(Resistance to Dust & Moisture)	-	6000	-
21.15(Insulation Resistance and Electric Strength)	-	6000	-
21.16(Resistance to Heat , fire and tracking)	-	4000	-
21.7.1(General)	-	2000	-
21.7.3(Terminals and supply connections)	-	4000	-
21.7.4(Control units)	-	2000	-
21.7.5(Mechanical strength)	-	5000	-

-
Included w.e.f.26.11.2024

129

IS 10322 : Part 5 : Sec 7 (2017)

Luminaires: Part 5 particular requirements: Sec 7 lighting chains (First Revision)

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
20.4(General Test Requireements)	-	2000	-
20.5(Classification of Luminaires')	-	2000	-
20.6(Marking)	-	3000	-
20.7(Construction)	-	4000	-
20.8(Creepage Distance and Clearances)	-	3000	-
20.9(Provision for earthing)	-	5000	-
20.10(Terminals)	-	4000	-
20.11(External & Internal Wiring)	-	5000	-
20.12(Protection against electric shock)	-	4000	-
20.13(Endurance Tests and Thermal Tests)	-	8000	-
20.14(Resistance to Dust & Moisture)	-	6000	-
20.15(Insulation Resistance and Electric Strength)	-	7000	-
20.16(Resistance to Heat , fire and tracking)	-	6000	-

-
Included w.e.f.26.11.2024

130

IS 10322 : Part 5 : Sec 6 (2013)

Luminaires: Part 5 particular requirements: Sec 6 handlamps

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.2(Packing -Each Package shall bear the following Particulars)	-	2000	-
4(General Test Requireements)	-	1000	-
5(Classification of Luminaires')	-	1000	-
6.0(Marking)	-	2000	-
7.0(Construction)	-	3000	-
8.0(Creepage Distance and Clearances)	-	3000	-
9.0(Provision for earthing)	-	5000	-
10.0(Terminals)	-	4000	-
11.0(External & Internal Wiring)	-	6000	-
12.0(Protection against electric shock)	-	3000	-
13.0(Endurance Tests and Thermal Tests)	-	8000	-
14.0(Resistance to Dust & Moisture)	-	6000	-
15.0(Insulation Resistance and Electric Strength)	-	6000	-
16.0(Resistance to Heat , fire and tracking)	-	6000	-

-
Included w.e.f.26.11.2024

131

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	2000	-
5(Classification of Luminaires')	-	3000	-
6.0(Marking)	-	3000	-
7.0(Construction)	-	4000	-
8.0(Creepage Distance and Clearances)	-	2000	-
9.0(Provision for earthing)	-	5000	-
10.0(Terminals)	-	3000	-
11.0(External & Internal Wiring)	-	4000	-
12.0(Protection against electric shock)	-	4000	-
13.0(Endurance Tests and Thermal Tests)	-	6000	-
14.0(Resistance to Dust & Moisture)	-	5000	-
15.0(Insulation Resistance and Electric Strength)	-	4000	-
16.0(Resistance to Heat , fire and tracking)	-	4000	-
17.0(Photometric Test)	-	6000	-
(Cl.4.24) (Annex-P)(UV Radiations for metal halide lamps)	-	2000	-
4.26.2(Short Circuit Protection)	-	2000	-

-
Included w.e.f.26.11.2024 Exclusion (Cl.4.24) (Annex-P) (UV Radiations for metal halide lamps) 4.26.2 (Short Circuit Protection)

132

IS 16103 : Part 1 (2012)

Led modules for general lighting: Part 1 safety requirements

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	3000	-
8(Terminals)	-	3000	-
9(PROVISION FOR EARTHING)	-	5000	-
10(Protection against accidental contact with live parts)	-	5000	-
11(Mositure Resistance and Insulation)	-	5000	-
12(Electric Strength)	-	5000	-
13(Fault conditions)	-	4000	-
15(Construction)	-	3000	-
16(Creepage distance and clearances)	-	2000	-
17(Screws, current carrying parts and connections)	-	4000	-
18(Resistance to heat, fire and tracking)	-	4000	-
19(Resistance to corrosion)	-	4000	-
21(Heat management)	-	3000	-
21(Heat management)	-	2000	-

-
Included w.e.f 01.01.2025

133

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

47000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	3000	-
8(Protection against accidental contact with live parts)	-	3000	-
9(Terminals)	-	4000	-
10(PROVISION FOR EARTHING)	-	5000	-
11(MOISTURE RESISTANCE)	-	4000	-
12(Electric Strength)	-	4000	-
13(Thermal endurance test for winding of ballasts)	-	3000	-
14(Fault conditions)	-	4000	-
15(Transformer heating)	-	5000	-
16(Construction)	-	4000	-
17(Creepage distance and clearances)	-	3000	-
18(Screws, current carrying parts and connections)	-	3000	-
19(Resistance to heat, fire and tracking)	-	5000	-
20(Resistance to corrosion)	-	5000	-
16(Enclosures)	-	4000	-
16(Bridging resistor in primary circuit)	-	3000	-
16(Capacitor and RC units)	-	4000	-
16(RF suppression (X-Y capacitors))	-	4000	-
16(Inductor)	-	4000	-
16(MOV/VDR)	-	4000	-
16(SMPS/Mains Transformer)	-	4000	-
16(PCB material)	-	4000	-
19(Metal base PCB for LED)	-	4000	-
19(Transparent cover)	-	5000	-
19(Bobbin)	-	4000	-
16(Insulated tape)	-	3000	-
16(Heat shrinkage sleeve)	-	4000	-
19(Terminals)	-	4000	-
16(Connector)	-	4000	-
16(Fuse)	-	4000	-
16(Internal wire)	-	4000	-
16(LED)	-	4000	-
16(Opto-coupler)	-	4000	-
16(Opto-coupler)	-	4000	-
16(EMI/EMC filter)	-	4000	-
16(Winding wire)	-	4000	-
16(Thin sheet materials)	-	4000	-
7(Marking)	-	3000	-
8("PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS")	-	3000	-
9(TERMINALS)	-	3000	-
10(PROVISIONS FOR PROTECTIVE EARTHING)	-	4000	-
11(MOISTURE RESISTANCE AND INSULATION)	-	4000	-
12(ELECTRIC STRENGTH)	-	4000	-
14(FAULT CONDITIONS)	-	4000	-
15(TRANSFORMER HEATING)	-	4000	-
16(CONSTRUCTION)	-	4000	-
17(CREEPAGE DISTANCES AND CLEARANCES)	-	2000	-
18("SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS")	-	3000	-
19(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	2000	-
20(RESISTANCE TO CORROSION)	-	3000	-
4(GENERAL REQUIREMENTS)	-	2000	-
5(GENERAL NOTES ON TESTS)	-	2000	-
6(CLASSIFICATION)	-	3000	-
7(Marking)	-	2000	-
8(Protection against accidental contact with live parts)	-	3000	-
9(Terminals)	-	3000	-
10(PROVISION FOR EARTHING)	-	5000	-
11(MOISTURE RESISTANCE)	-	6000	-
12(Electric Strength)	-	5000	-
13(Thermal endurance test for winding of ballasts)	-	5000	-
14(Fault conditions)	-	5000	-
15(Transformer heating)	-	8000	-
16(Construction)	-	2000	-
17(Creepage distance and clearances)	-	3000	-
18(Screws, current carrying parts and connections)	-	2000	-
19(Resistance to heat, fire and tracking)	-	5000	-
20(Resistance to corrosion)	-	3000	-
16(Enclosures)	-	1000	-
16(Bridging resistor in primary circuit)	-	0	-
16(Capacitor and RC units)	-	0	-
16(RF suppression (X-Y capacitors))	-	0	-
16(Inductor)	-	0	-
16(MOV/VDR)	-	0	-
16(SMPS/Mains Transformer)	-	0	-
16(PCB material)	-	0	-
19(Metal base PCB for LED)	-	0	-
19(Transparent cover)	-	0	-
19(Bobbin)	-	0	-
16(Insulated tape)	-	0	-
16(Heat shrinkage sleeve)	-	0	-
19(Terminals)	-	1000	-
16(Connector)	-	0	-
16(Fuse)	-	0	-
16(Internal wire)	-	0	-
16(LED)	-	0	-
16(Opto-coupler)	-	0	-
16(Opto-coupler)	-	0	-
16(EMI/EMC filter)	-	0	-
16(Winding wire)	-	0	-
16(Thin sheet materials)	-	0	-
7(Marking)	-	2000	-
8("PROTECTION AGAINST ACCIDENTAL CONTACT WITH LIVE PARTS")	-	3000	-
9(TERMINALS)	-	2000	-
10(PROVISIONS FOR PROTECTIVE EARTHING)	-	5000	-
11(MOISTURE RESISTANCE AND INSULATION)	-	3000	-
12(ELECTRIC STRENGTH)	-	5000	-
14(FAULT CONDITIONS)	-	5000	-
15(TRANSFORMER HEATING)	-	8000	-
16(CONSTRUCTION)	-	5000	-
17(CREEPAGE DISTANCES AND CLEARANCES)	-	3000	-
18("SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS")	-	3000	-
19(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	8000	-
20(RESISTANCE TO CORROSION)	-	5000	-
4(GENERAL REQUIREMENTS)	-	1000	-
5(GENERAL NOTES ON TESTS)	-	1000	-
6(CLASSIFICATION)	-	1000	-

-
Included w.e.f 01.01.2025 Exclusion : Cl 16 (RF suppression (X-Y capacitors), MOV/VDR), (SMPS/Mains Transformer), (PCB material), (Insulated tape), (Heat shrinkage sleeve), (Connector), (Fuse), (Internal wire), (LED), (Opto-coupler), (EMI/EMC filter), (Winding wire) Cl 19 (Metal base PCB for LED), (Transparent cover), (Bobbin)

134

IS 16102 : Part 1 (2012)

Self - Ballasted led lamps for general lighting services: Part 1 safety requirements

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking)	-	3000	-
6(Interchangeability)	-	4000	-
7(Protection against accidental contact with live parts)	-	3000	-
8(Insulation Resistance and Electric Strength)	-	6000	-
9(MECHANICAL STRENGTH)	-	4000	-
10(cap temperature)	-	8000	-
11(Resistance to Heat)	-	3000	-
12(Resistance to Flame and Ignition)	-	3000	-
13(Fault conditions)	-	4000	-
14(Creepage distance and clearances)	-	2000	-
4(General requirement and General test requirements)	-	3000	-
5(Marking)	-	3000	-
6(Interchangeability)	-	4000	-
7(Protection against accidental contact with live parts)	-	3000	-
8(Strength after humidity treatment)	-	4000	-
9(Mechanical strength)	-	3000	-
10(Cap temperature rise)	-	4000	-
11(Resistance to heat)	-	4000	-
13(Fault conditions)	-	6000	-
14(Creepage distances and clearances)	-	2000	-
15(Selection of lamps for tests (Sampling))	-	3000	-
16(Condition of compliance)	-	2000	-
17(Tests)	-	2000	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	2000	-
Annex B(Lamps with operating position limitations)	-	2000	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	3000	-
12(Resistance to flame and ignition)	-	4000	-
5(Marking)	-	3000	-
6(Interchangeability)	-	4000	-
7(Protection against accidental contact with live parts)	-	4000	-
8(Insulation Resistance and Electric Strength)	-	4000	-
9(MECHANICAL STRENGTH)	-	3000	-
10(cap temperature)	-	5000	-
11(Resistance to Heat)	-	2000	-
12(Resistance to Flame and Ignition)	-	3000	-
13(Fault conditions)	-	4000	-
14(Creepage distance and clearances)	-	2000	-
4(General requirement and General test requirements)	-	2000	-
5(Marking)	-	3000	-
6(Interchangeability)	-	3000	-
7(Protection against accidental contact with live parts)	-	3000	-
8(Strength after humidity treatment)	-	4000	-
9(Mechanical strength)	-	3000	-
10(Cap temperature rise)	-	5000	-
11(Resistance to heat)	-	2000	-
13(Fault conditions)	-	4000	-
14(Creepage distances and clearances)	-	2000	-
15(Selection of lamps for tests (Sampling))	-	2000	-
16(Condition of compliance)	-	2000	-
17(Tests)	-	2000	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	2000	-
Annex B(Lamps with operating position limitations)	-	2000	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	2000	-
12(Resistance to flame and ignition)	-	3000	-
5(Marking)	-	3000	-
6(Interchangeability)	-	4000	-
7(Protection against accidental contact with live parts)	-	4000	-
8(Insulation Resistance and Electric Strength)	-	5000	-
9(MECHANICAL STRENGTH)	-	2000	-
10(cap temperature)	-	4000	-
11(Resistance to Heat)	-	5000	-
12(Resistance to Flame and Ignition)	-	4000	-
13(Fault conditions)	-	4000	-
14(Creepage distance and clearances)	-	4000	-
4(General requirement and General test requirements)	-	3000	-
5(Marking)	-	3000	-
6(Interchangeability)	-	3000	-
7(Protection against accidental contact with live parts)	-	3000	-
8(Strength after humidity treatment)	-	5000	-
9(Mechanical strength)	-	5000	-
10(Cap temperature rise)	-	5000	-
11(Resistance to heat)	-	4000	-
13(Fault conditions)	-	4000	-
14(Creepage distances and clearances)	-	4000	-
15(Selection of lamps for tests (Sampling))	-	1000	-
16(Condition of compliance)	-	4000	-
17(Tests)	-	2000	-
Annex A(Ovreview of systems composed of LED modules and control gear)	-	1000	-
Annex B(Lamps with operating position limitations)	-	1000	-
4(GENERAL REQUIREMENT AND GENERAL TEST REQUIREMENTS)	-	1000	-
12(Resistance to flame and ignition)	-	3000	-

-
Included w.e.f 01.01.2025

135

IS 2619 (2018)

Glass beakers - Specification (Third Revision)

13000 View breakup
-

Clause No.	Exclusion	Remark
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	-
Cl.5 Capacity (a)overflow of capacity of a beaker shall exceed the nominal capacity by at least 5 %;)	-	-
Cl.6 Material(Beakers shall be made of borosilicate glass 3.3 in accordance with ISO 3585. The glass shall be reasonably free from residual strain and from visible glass defects which might impair the safety and performance of the beaker.)	-	-
Cl.7.1 Dimensions(Low-form and tall-form beakers shall observe the dimensions specified in Table 1 and thick-walled beakers the dimensions specifed in Table 2. The tolerances on the external diameter shall be ±5 % of the value given in the tables.)	-	-
Cl.7.2 Radius at base(Beakers having a nominal capacity of 250 ml or greater shall have an external radius at the junction between the base and the side of 10 % to 20 % of the external diameter.)	-	-
Cl.7.2 Radius at base(Beakers having a nominal capacity less than 250 ml shall have a minimum radius at the junction between the base and the side of 5 % of the external diameter.)	-	-
Cl.7.3 Wall thickness(Substantial local irregularities from the minimum values for wall thickness given in the tables shall be avoided. That means, the minimum wall thickness shall fall at no place below the values given in Table 1 and Table 2 and the beakers shall comply with the requirement for thermal shock endurance specified in 8.5.)	-	-
Cl.8.1 Base(The design of the base shall enable the beaker to stand vertically on a plane horizontal surface without spinning or rocking)	-	-
8.2 Upper edge(The side of the beaker shall be slightly flared near the brim in a smooth and regular curve. The diameter of the brim shall be of the order of 5 % to 15 % greater than the diameter of the body. The edge of the brim shall be finished in a plane parallel with that of the horizontal base.)	-	-
Cl. 8.3 Spout(The spout shall be shaped so that, when the beaker is filled with water, the water may be poured in a regular stream clear of the side of the beaker. When the beaker is placed on a horizontal surface and filling is continued beyond its overflow capacity, the water shall first overflow from the spout and not from any other part of the brim.)	-	-
Cl.8.4 Scale(Beakers may be provided with a scale, which should approximately indicate the volume contained in the beaker.)	-	-
Cl.8.5 Thermal shock resistance(Beakers shall have a thermal shock resistance of 160 °C when tested in accordance with ISO 718.)	-	-
Cl.5 Capacity (b) Distance between the levels corresponding to the nominal and overflow capacities shall be at least 10 mm.)	-	-

-
Included w.e.f.05.11.2024

136

IS 1117 (2018)

Laboratory glassware - Single - Volume pipettes (Second Revision)

13000 View breakup
-

Clause No.	Exclusion	Remark
6.1.1&3(Marking)	-	-
3(Class of Accuracy)	-	-
4.1(Nominal capacities)	-	-
4.2(Accuracy)	-	-
5.1(Material)	-	-
5.1(Material)	-	-
5.1.1(Limit of Alkalinity)	-	-
5.2(Pattern of Pipette)	-	-
5.3(Workmanship & Finish)	-	-
5.4(i) Distance of graduation line from top of pipette.)	-	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	-
5.4(iv) Wall thickness)	-	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	-
5.4(b) Other pipettes)	-	-
5.4(v) Dia. of safety bulb (if provided ))	-	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	-
5.4(vii) Overall length, L)	-	-
5.4(viii) Length of suction tube, L1 )	-	-
5.4(ix) Length of delivery tube, L2 )	-	-
5.4(x) Internal dia. of suction tube D1 )	-	-
5.4(xi) External dia. of bulb D2 )	-	-
5.4(xii) External dia. of delivery tube D3 )	-	-
5.5(Delivery Time)	-	-
5.5(Delivery Time)	-	-
5.6&7(Graduation line & Visibility )	-	-
6.1.2(Marking)	-	-
6.1.1&3(Marking)	-	-
3(Class of Accuracy)	-	-
4.1(Nominal capacities)	-	-
4.2(Accuracy)	-	-
5.1(Material)	-	-
5.1(Material)	-	-
5.1.1(Limit of Alkalinity)	-	-
5.2(Pattern of Pipette)	-	-
5.3(Workmanship & Finish)	-	-
5.4(i) Distance of graduation line from top of pipette.)	-	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	-
5.4(iv) Wall thickness)	-	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	-
5.4(b) Other pipettes)	-	-
5.4(v) Dia. of safety bulb (if provided ))	-	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	-
5.4(vii) Overall length, L)	-	-
5.4(viii) Length of suction tube, L1 )	-	-
5.4(ix) Length of delivery tube, L2 )	-	-
5.4(x) Internal dia. of suction tube D1 )	-	-
5.4(xi) External dia. of bulb D2 )	-	-
5.4(xii) External dia. of delivery tube D3 )	-	-
5.5(Delivery Time)	-	-
5.5(Delivery Time)	-	-
5.6&7(Graduation line & Visibility )	-	-
6.1.2(Marking)	-	-
6.1.1&3(Marking)	-	-
3(Class of Accuracy)	-	-
4.1(Nominal capacities)	-	-
4.2(Accuracy)	-	-
5.1(Material)	-	-
5.1(Material)	-	-
5.1.1(Limit of Alkalinity)	-	-
5.2(Pattern of Pipette)	-	-
5.3(Workmanship & Finish)	-	-
5.4(i) Distance of graduation line from top of pipette.)	-	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	-
5.4(iv) Wall thickness)	-	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	-
5.4(b) Other pipettes)	-	-
5.4(v) Dia. of safety bulb (if provided ))	-	-
5.4(vi)Distance from top of pipette to bottom of safety bulb )	-	-
5.4(vii) Overall length, L)	-	-
5.4(viii) Length of suction tube, L1 )	-	-
5.4(ix) Length of delivery tube, L2 )	-	-
5.4(x) Internal dia. of suction tube D1 )	-	-
5.4(xi) External dia. of bulb D2 )	-	-
5.4(xii) External dia. of delivery tube D3 )	-	-
5.5(Delivery Time)	-	-
5.5(Delivery Time)	-	-
5.6&7(Graduation line & Visibility )	-	-
6.1.2(Marking)	-	-
4.1(unit of volume)	-	-
4.2(delivery volume)	-	-
4.3(reference temperature)	-	-
5.1(Types and Classes of accuracy)	-	-
5.2(Types of single- volume pipette)	-	-
7.1(Material)	-	-
7.2(Shape)	-	-
7.3(Bulb)	-	-
7.4(Dimensions)	-	-
7.5(Top of Pipette)	-	-
7.6(Delivery Jet)	-	-
7.7(Delivery Time)	-	-
7.8(Waiting Time)	-	-
Clause- 8.0(Graduation Line)	-	-
Clause- 9.0(Setting of the Meniscus)	-	-
Clause-10.0(Marking)	-	-
Clause- 6.0(Maximum Permissible error)	-	-

-
Included w.e.f. 30.10.2024

137

IS 1381 : Part 1 (2003)

Laboratory glassware - Narrow - Necked boiling flasks (Second Revision)

12000 View breakup
-

Clause No.	Exclusion	Remark
3, 4(Type of Flask)	-	-
3.1, 4.1(Series of Nominal Capacity)	-	-
3.2, 4.2(Nominal Capacity )	-	-
3.3, 4.3(Material )	-	-
3.4, 3.4.1 & 4.4, 4.4.1(Construction- a) Stability )	-	-
3.4, 3.4.2 & 4.4, 4.4.2(Construction- b) Neck )	-	-
3.5, 4.5(Dimensions (in mm) (Table 1&2))	-	-
3.5.2(Neck Length)	-	-
3.5.3, 4.5.2(Dimensions of base )	-	-
3.5.4, 4.5.3(Wall thickness)	-	-
5(Marking )	-	-

-
Included w.e.f.05.11.2024

138

IS 915 (2012)

Laboratory glassware - One - Mark volumetric flasks (Third Revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1(Material)	-	13500	-
Table 1(Nominal Capacity)	-	13500	-
Table 1(Internal Neck Diameter)	-	13500	-
Table 1(Distance of graduation line)	-	13500	-
Table 1(Overall Height)	-	13500	-
Table 1(Bulb Diameter)	-	13500	-
Table 1(Base Diameter)	-	13500	-
Table 1(Wall Thickness)	-	13500	-
Table 1(Ground joint k4)	-	13500	-
Table 1(Ground joint k6)	-	13500	-
8.3(Shape)	-	13500	-
8.4(Neck)	-	13500	-
8.5(Stopper)	-	13500	-
8.6(Dimensions)	-	13500	-
9.0(Graduation Line)	-	13500	-
Table-2(Nominal capacity)	-	13500	-
Table-2(Internal neck diameter)	-	13500	-
Table-2(Distance of graduation line 1))	-	13500	-
Table-2(Overall height 2))	-	13500	-
Table-2(Bulb diameter)	-	13500	-
Table-2(Base diameter)	-	13500	-
Table-2(Wall thickness)	-	13500	-
Table-2(Ground joint 3) k4)	-	13500	-
Table-2(Ground joint 3) k6)	-	13500	-
12.1(Visibility of graduation line, figures and marking)	-	13500	-
12.2(Visibility of graduation line, figures and marking)	-	13500	-
Clause. 7.0(Accuracy)	-	13500	-

-
included w.e.f.05.11.2024

139

IS 878 (2008)

Laboratory glassware - Graduated measuring cylinders (Second Revision)

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1(Nominal capacity)	-	10500	-
Table-1(Overall height)	-	10500	-
Table-1(Distance from top of scale to top of cylinder)	-	10500	-
Table-1(Internal height to highest graduation line)	-	10500	-
Table-1(Sub-divisions)	-	10500	-
Table-1(capacity at lowest graduation line)	-	10500	-
Cl-9.1(Wall thickness)	-	10500	-
Cl-9.2(Stability)	-	10500	-
Cl-9.3(Base)	-	10500	-
Cl-9.4(Rim and spout)	-	10500	-
Cl-9.5(Neck and stopper)	-	10500	-
Cl-9.6, Table-2(Nominal capacity)	-	10500	-
Cl-9.6, Table-2(Overall height)	-	10500	-
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	10500	-
Cl-9.6, Table-2(Internal height to highest graduation line)	-	10500	-
Cl-9.6, Table-2(Sub divisions)	-	10500	-
Cl-9.6, Table-2(capacity at lowest graduation line)	-	10500	-
Cl-10.1(Graduation)	-	10500	-
Cl-10.2(Figuring)	-	10500	-
Cl-11(Accuracy testing)	-	10500	-
Cl-13(Visibility of graduation lines, figures and marking)	-	10500	-
Clause. 8.0(Material)	-	10500	-
Table- 1(Max. Permissible Error (Class- a))	-	10500	-
Table- 1(Max. Permissible Error (Class- b))	-	10500	-
Table- 2(Max. Permissible Error (Type-2))	-	10500	-
Table-1(capacity at lowest graduation line)	-	10500	-
Cl-9.1(Wall thickness)	-	10500	-
Cl-9.2(Stability)	-	10500	-
Cl-9.3(Base)	-	10500	-
Cl-9.4(Rim and spout)	-	10500	-
Cl-9.5(Neck and stopper)	-	10500	-
Cl-9.6, Table-2(Nominal capacity)	-	10500	-
Cl-9.6, Table-2(Overall height)	-	10500	-
Cl-9.6, Table-2(Distance from top of scale to top of cylinder)	-	10500	-
Cl-9.6, Table-2(Internal height to highest graduation line)	-	10500	-
Cl-9.6, Table-2(Sub divisions)	-	10500	-
Cl-9.6, Table-2(capacity at lowest graduation line)	-	10500	-
Cl-10.1(Graduation)	-	10500	-
Cl-10.2(Figuring)	-	10500	-
Cl-11(Accuracy testing)	-	10500	-
Cl-13(Visibility of graduation lines, figures and marking)	-	10500	-
Clause. 8.0(Material)	-	10500	-
Table- 1(Max. Permissible Error (Class- a))	-	10500	-
Table- 1(Max. Permissible Error (Class- b))	-	10500	-
Table- 2(Max. Permissible Error (Type-2))	-	10500	-

-
Included w.e.f.05.11.2024

140

IS 2993 : Part 2 (2024)

a.c. Motor Capacitors Part 2 Motor Start Capacitors ( Third Revision )

ELECTRICAL

500000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1.1(General)	-	35000	-
5.1.7(Voltage test between the terminals)	-	35000	-
5.1.8(Voltage test between terminals and case)	-	35000	-
5.1.9(Capacitance measurement)	-	35000	-
5.1.10(Check of dimensions)	-	35000	-
5.1.10(Check of dimensions)	-	35000	-
5.1.11.1(Robustness of terminations)	-	35000	-
5.1.11.2(Soldering)	-	35000	-
5.1.11.3(Vibration)	-	35000	-
5.1.12(Sealing test)	-	35000	-
5.1.13(Endurance test)	-	35000	-
5.1.14(Damp heat test)	-	35000	-
5.1.15(Self-healing test)	-	35000	-
5.1.16(Destruction test)	-	35000	-
5.1.17.1(Ball-pressure test)	-	35000	-
5.1.17.2(Glow-wire test)	-	35000	-
5.1.17.3(Tracking test)	-	35000	-
5.2(Overloads)	-	35000	-
5.3.1(Creepage distances and clearances)	-	35000	-
5.3.2(Terminals and connecting cables)	-	35000	-
5.3.3(Earth connections)	-	35000	-
5.3.4(Discharge devices)	-	35000	-
5.3.5(Pollution)	-	35000	-
5.4(Marking)	-	35000	-
6.1.6(Voltage test between the terminals)	-	35000	-
6.1.7(Voltage test between terminals and case)	-	35000	-
6.1.8(Capacitance and power factor measurement)	-	35000	-
6.1.9(Check of dimensions)	-	35000	-
6.1.10.1(Robustness of terminations)	-	35000	-
6.1.10.2(Soldering)	-	35000	-
6.1.10.3(Vibration)	-	35000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	35000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	35000	-
6.1.10.5(Rapid change of temperature)	-	35000	-
6.1.11(Sealing test)	-	35000	-
6.1.12(Endurance test)	-	35000	-
6.1.13(Damp heat test)	-	35000	-
6.1.14(Pressure relief test)	-	35000	-
6.1.15.1(Ball-pressure test)	-	35000	-
6.1.15.2(Glow-wire test)	-	35000	-
6.1.15.3(Tracking test)	-	35000	-
6.2(Overloads)	-	35000	-
6.3.1(Creepage distances and clearances)	-	35000	-
6.3.2(Terminals and connecting cables)	-	35000	-
6.3.3(Earth connections)	-	35000	-
6.3.4(Discharge devices)	-	35000	-
6.3.5(Pollution)	-	35000	-
6.4(Marking)	-	35000	-
7.2.1(Measurement of working voltage)	-	35000	-
7.2.2(Influence of capacitance)	-	35000	-
7.3(Checking capacitor temperature)	-	35000	-
7.4(Checking transients)	-	35000	-
7.5(Storage of electrolytic capacitors)	-	35000	-
Annex A(Test voltage)	-	35000	-

-
included w.e.f.30.10.2024

141

IS 2993 : Part 1 (2024)

a.c. Motor Capacitors Part 1 General - Performance, Testing and Rating - Safety Requirements - Guidance for Installation and Operation ( Third Revision )

ELECTRICAL

500000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(General)	-	35000	-
5.5(Tangent of loss angle)	-	35000	-
5.7("Voltage test between terminals ")	-	35000	-
5.8(Voltage test between terminals and case)	-	35000	-
5.9(Capacitance measurement)	-	35000	-
5.1(Check of dimensions)	-	35000	-
5.11(Mechanical tests)	-	35000	-
5.12(Sealing test)	-	35000	-
5.13(Endurance test)	-	35000	-
5.14(Damp heat test)	-	35000	-
5.15(Self-healing test)	-	35000	-
5.16(Destruction test)	-	35000	-
5.17(Resistance to heat, fire and tracking)	-	35000	-
5.17.1(Ball-pressure test)	-	35000	-
5.17.2(Glow-wire test)	-	35000	-
5.17.3(Tracking test)	-	35000	-
6.1(Maximum permissible voltage)	-	35000	-
6.2("Maximum permissible current ")	-	35000	-
6.3(Maximum permissible reactive output)	-	35000	-
7(Safety requirements)	-	35000	-
7.1(Requirements for Creepage distances and clearances)	-	35000	-
7.2(Terminals and connecting cables)	-	35000	-
7.3(Earth connections)	-	35000	-
7.4(Discharge devices)	-	35000	-
8(Marking)	-	35000	-
9.2.1(Measurements of working voltage)	-	35000	-
9.2.2(Influence of capacitance)	-	35000	-
9.3(Checking capacitor temperature)	-	35000	-
9.4(Checking transients)	-	35000	-
9.5(Leakage current)	-	35000	-
5.9(Capacitance measurement)	-	35000	-

-
included w.e.f.30.10.2024

142

IS 2993 (1998)

A.C. motor capacitors (Second Revision)

ELECTRICAL

450000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.6(Visual Examination)	-	50000	-
5.1(Check marking)	-	50000	-
2.1(Check of dimensions)	-	50000	-
2.9(Capacitance measurement)	-	50000	-
2.11.1(Robustness of terminations)	-	50000	-
2.11.1.1(Tensile)	-	50000	-
2.11.1.2(Bending (half cf the terminations))	-	50000	-
2.11 .1.3(Torsion (other half of the terminations))	-	50000	-
2.11.1.4(Torque (screw terminals))	-	50000	-
2.11.1.5(Visual Examination)	-	50000	-
2.11.2(Soldering)	-	50000	-
2.11.3(Vibration)	-	50000	-
2.11.4(fixing bolt or stud (if fitted))	-	50000	-
2.12(Sealing Test)	-	50000	-
2.13(Endurance test)	-	50000	-
2.13.1(Endurance test :Testing in air with forced circulation)	-	50000	-
2.13.3(Endurance test : Conditions of compliance)	-	50000	-
2.14(Damping heat test)	-	50000	-
2.7(Voltage test between terminals)	-	50000	-
2.8(Voltage test between terminals and case)	-	50000	-
2.15(Self-healing test (if applicable))	-	50000	-
2.16.3(Destruction test : Test procedure)	-	50000	-
2.16.3.1(Destruction test : Test procedure - Preparation and pre-conditioning )	-	50000	-
2.16.3.2(Destruction test : Test procedure : DC conditioning)	-	50000	-
2.16.3.3(Destruction test : Test procedure : AC destruction test)	-	50000	-
2.5(Tangent of loss angle)	-	50000	-
2.16.4(Destruction tes: Evaluation of the failure )	-	50000	-
2.10(Check of dimensions)	-	50000	-
2.11.1.1(Test Ua - Tensile)	-	50000	-
2.11.1.2(Test Ub - Bending (half of the terminations))	-	50000	-
2.11.1.3(Test UC - Torsion (other half of the terminations))	-	50000	-
2.11.1.4(Test Ud - Torque (screw terminals))	-	50000	-
2.11.1.5(Visual examination)	-	50000	-
2.11.2(Soldering)	-	50000	-
2.11.3(Vibration)	-	50000	-
2.11.4(Fixing bolt or stud (if fitted))	-	50000	-
4.1(Creepage distances and clearances)	-	50000	-
4.2(Terminals and connecting cables)	-	50000	-
4.3(Earth connections)	-	50000	-
4.4(Discharge devices)	-	50000	-
2.10 (Elec)(Check of dimensions)	-	50000	-
2.11.1 (Elec)(Robustness of terminations)	-	50000	-
2.11.1.1 (Elec)(Tensile)	-	50000	-
2.11.1.2 (Elec)(Bending (half cf the terminations))	-	50000	-
2.11.1.3 (Elec)(Torsion (other half of the terminations))	-	50000	-
2.11.1.4 (Elec)(Torque (screw terminals))	-	50000	-
2.11.1.5 (Elec)(Visual Examination)	-	50000	-
2.11.2 (Elec)(Soldering)	-	50000	-
2.11.3 (Elec)(Vibration)	-	50000	-
2.11.4 (Elec)(fixing bolt or stud (if fitted))	-	50000	-

-
included w.e.f. 30.10.2024

143

IS 1709 (1984)

Specification for capacitors or electric fan motors (First Revision)

ELECTRICAL

270000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Rated Voltage)	-	20000	-
4.2(Rated Frequency)	-	20000	-
4.2(Ambient Air Temp.)	-	20000	-
4.2(Capacitance)	-	20000	-
4.2(Capacitor)	-	20000	-
Cl. 5.1(Capacitor)	-	20000	-
Cl. 5.2(Capacitor)	-	20000	-
Cl. 5.3(Capacitor)	-	20000	-
Cl. 5.4(Capacitor)	-	20000	-
Cl 5.5(Capacitor)	-	20000	-
Cl. 5.6(Capacitor)	-	20000	-
Cl. 5.7(Capacitor)	-	20000	-
a(ISS 1709 : 1984)	-	20000	-
b(Manufacturers name or trade-mark and Serial number)	-	20000	-
c(Rated Voltage)	-	20000	-
d(Rated frequency)	-	20000	-
e(Rated Capacitance)	-	20000	-
f(Rated anbient Temperature)	-	20000	-
Cl. 6.2(Product may also be marked with standard mark.)	-	20000	-
Cl. 7.2(The capcitors shall be visually examined for finish and marking)	-	20000	-
Cl. 7.3.1(Insualtion Resistance between terminal and container)	-	20000	-
Cl. 7.3.2(Insulation Resistance between terminals)	-	20000	-
Cl. 7.4.1(Capacitors shall be subjected to an ac voltage test as specified in Table 2.)	-	20000	-
Cl. 7.4.2(Capacitors shall be subjected for 10sec to a test between terminals and metal foil wrapped tightly around the surface of the container with s sinusoidal test voltages. Test Voltage:2000Vrms for 10sec During the test, no dielectric breakdown or flashover shall occur. )	-	20000	-
Cl. 7.5(Capacitance measured at rated frequency and rated voltage.)	-	20000	-
Cl.7.6(Tangent of Loss Angle measured at rated frequency and rated voltage. The maximum value of the tangent of loss angle for Self-healing MPP Type.)	-	50000	-
Cl. 7.7(A weight of 2kg shall be suspended freely from each one of them in turn for a period of 10 sec. There shall be no damage to the capacitor or termination after this loading.)	-	20000	-
Cl 7.8(Each termination shall withstand two consecutive bends as specified without damage to the capacitors)	-	20000	-
Cl 7.9(Soldering tags shall withstand two consecutive cycles of bending as specified without damage to the capacitors.)	-	20000	-
Cl. 7.10(There shall be no damage to the capacitors when the torque is applied to the nuts and screws of threaded terminations:)	-	20000	-
Cl. 7.11(The capacitor shall be not suffer any damage when the specified soldering iron is applied to the termination of 15 sec.)	-	20000	-
Cl. 7.12(Unenergized capacitor units kept in a position most likely to reveal leakage and heated throughout so that all parts of the container reach the temperature 5ºC higher the maximum operating temperature value. Total heating and cooling cycle time shall be 8 hours. After the sealing test No leakage shall occure.)	-	20000	-
Cl. 7.13(Capacitance)	-	20000	-
Cl. 7.13(Change in capacitance at 70°C as compare to 27°C. (Limit: 5%Max.) )	-	50000	-
Cl. 7.13(Change in capacitance at 0°C as compare to 27°C. (Limit: 3%Max.) )	-	50000	-
Cl. 7.14.1(Before test capacitance shall be measured. Th capacitor shall be subjected for 10 seconds to an ac voltage of 1.5 ti9mes the rated voltage. If rewer than five breakdown occure during the time, The voltage shall be increased slowly until five breakdown occured until voltage occured 3.5 times the rated voltage. voltage reduced to 0.8 times, no breakdown is permitted after decreased of voltage.)	-	50000	-
Cl. 7.14.2(If only one or no breakdown has occurred since begning of the test when voltage has reached 3.5 times the rated voltage, the test shall be repeated on aonther identical capacitor.)	-	50000	-
Cl.7.14.3(Before and after the test,the cpacitance shall be measured, A chage not greater than 0.3 %in its value shall be allowec.)	-	50000	-
Cl. 7.15(After the test Capcitance variation)	-	50000	-
Cl. 7.16(The capacitors are mounted in a air circulated test chamber as specified and capacitors are energized at test voltage 1.25UN for 500hr Continuously at 50Hz. During the test no permanent breskdown,intertuption or flashover shall occure.)	-	50000	-
Cl. 7.16(Change in capacitance, (Limit: 5%Max.) )	-	50000	-
Cl. 7.16(At the end of the test, the capacitors shall cool down freely to the ambient temperature and the tangent of loss angle shall be then measured. )	-	50000	-
Cl. 7.16(Change in Tangent of Loss angle, (Limit: ----) )	-	50000	-
Cl. 7.17(The capacitor sample was mounted in a circulating air oven maintained at a temperature 10ºC above the maximum operating temperature as specified without energizing. Capacitor energized at 1.4 times rated voltage by applying test voltage between terminal for 1 h, then 1.6 times rated voltage for 1 h, then 1.8 times rated voltage for 1 h, then 2.0 times rated voltage for 1 h then switch off. Then 2.0 times the rated voltage for an 8 h period each in four cycles of 24h. After completion of the test, the capacito is consider to have passe destruction test if a) Current through it has not been interruped by the delayed action test circuit fuse or by any internal fuse. b) The currnt through it has been interrputed without any harmful effect occurring. c)Three delayed action test ciucuit fuse have cleared without any hamfu effect occurring.d) The endurance is entact at the end of test e) The test voltage between terminals and container is passed at the end of the test.)	-	50000	-
Cl. 7.16(At the end of the test, the capacitors shall cool down freely to the ambient temperature and then capacitance shall be measured.)	-	50000	-

-
Included.w.e.f.06.12.2024

144

IS 17634 (2022)

Storage Units - Specification

33500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 5(DIMENSIONS)	-	1000	/
CLAUSE 6(SURFACE PERFORMANCE)	-	5000	/
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	8000	/
CLAUSE 7.1(SAFETY TESTS (General))	-	1000	/
CLAUSE 7.2(Test for Non-Movable Parts)	-	1000	/
CLAUSE 7.2.1(Shelves)	-	1000	/
CLAUSE 7.2.1.2(Deflection of shelves)	-	1000	/
CLAUSE 7.2.2.1(Sustained load test for tops and bottoms)	-	1000	/
CLAUSE 7.2.2.2(Static load test for tops and bottoms)	-	1000	/
CLAUSE 7.2.3.1(Strength of clothes-rail supports)	-	1000	/
CLAUSE 7.2.3.2(Dislodgement of clothes rail)	-	1000	/
CLAUSE 7.2.4.2(Drop test)	-	1000	/
CLAUSE 7.2.4.3(Tests for units with castors or wheels)	-	1000	/
CLAUSE 7.3.1(Pivoted Doors)	-	1000	/
CLAUSE 7.3.1.2.1(Vertical load on pivoted door)	-	1000	/
CLAUSE 7.3.1.2.2(Horizontal load on pivoted door)	-	1000	/
CLAUSE 7.3.1.3(Slam-shut test of pivoted doors)	-	1000	/
CLAUSE 7.3.1.4(Durability of pivoted doors)	-	1000	/
CLAUSE 7.3.2(Sliding Doors and Horizontal Roll-fronts)	-	1000	/
CLAUSE 7.3.2.2(Slam shut/open test of sliding doors and horizontal roll-fronts)	-	1000	/
CLAUSE 7.3.2.3(Durability of sliding doors and horizontal roll-fronts)	-	10000	/
CLAUSE 7.3.3.1(Strength of bottom-hinged flaps)	-	1000	/
CLAUSE 7.3.3.2(Durability of flaps)	-	5000	/
CLAUSE 7.3.3.3(Drop test for top-hinged flaps)	-	1000	/
CLAUSE 7.3.4(Vertical Roll-Fronts)	-	1000	/
CLAUSE 7.3.4.1(Slam shut/open test of vertical roll-fronts)	-	1000	/
CLAUSE 7.3.4.2(Durability of vertical roll-fronts)	-	5000	/
CLAUSE 7.3.5(Extension Element)	-	1000	/
CLAUSE 7.3.5.2(Strength of extension elements)	-	1000	/
CLAUSE 7.3.5.3(Durability of extension elements)	-	15000	/
CLAUSE 7.3.5.4(Slam shut/open test of extension element)	-	1000	/
CLAUSE 7.3.5.5(Displacement of extension element bottoms)	-	1000	/
CLAUSE 7.3.5.6(Interlock test)	-	1000	/
CLAUSE 7.3.6(Locking and Latching Mechanism Tests)	-	1000	/
CLAUSE 7.3.6.2(Strength test for locking and latching mechanisms for extension elements)	-	1000	/
CLAUSE 7.3.6.3(Locking and latching mechanisms for doors, flaps and roll-fronts)	-	1000	/
CLAUSE 7.3.6.4(Durability test of locking and latching mechanisms)	-	4000	/
CLAUSE 7.3.7(Pull Force Test)	-	1000	/
CLAUSE 7.3.7(Pull Force Test)	-	1000	/
CLAUSE 7.3.8(Top Load Ease Cycle Test)	-	1000	/
CLAUSE 7.3.9(Durability Test for Units with Seating Surfaces – Cyclic Impact)	-	4000	/
CLAUSE 7.3.10("Drop Test – Dynamic – for Units with Seat Surfaces")	-	1000	/
CLAUSE 7.4.1.3(Sustained load test (overload))	-	1000	/
CLAUSE 7.4.1.4(Dislodgement test)	-	1000	/
CLAUSE 7.5(Stability Tests)	-	1000	/
CLAUSE 7.5.2.1("Units that can be adjusted to a Height of 1 000 mm or less")	-	1000	/
CLAUSE 7.5.2.2("Units that can be adjusted to a height of more than 1 000 mm")	-	1000	/
CLAUSE 7.5.3(Opening Doors, Extension Elements and Flaps, All Storage Units Unloaded)	-	1000	/
CLAUSE 7.5.6(Vertical Force Stability Test for Storage Units)	-	1000	/
CLAUSE 7.5.7(Stability Test for Pedestals/Storage Units with Seat Surfaces)	-	1000	/
CLAUSE 7.5.8("Dynamic Stability Test for Units with Castors")	-	1000	/
CLAUSE 7.5.9(Strength Test for Wall Attachments)	-	1000	/
CLAUSE 7.3.3(Flaps)	-	1000	/

-
Included w.e.f 18.10.2024

145

IS 17636 (2021)

Bunk Beds - Specification

13000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(DESIGN AND WORKMANSHIP)	-	1000	/
CLAUSE 5(DIMENSIONS)	-	1000	/
CLAUSE 6(SURFACE PERFORMANCE)	-	5000	/
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	8000	/
CLAUSE 7.5.1(Attachment, Deflection and Strength of Ladder and Treads)	-	1000	/
CLAUSE 7.6(Strength of Frame and Fastenings)	-	1000	/
CLAUSE 7.7(Stability Test)	-	1000	/
CLAUSE 7.8(Fastening of Upper Bed to Lower Bed)	-	1000	/

-
Included w.e.f 18.10.2024

146

IS 17635 (2022)

Beds - Specification

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(Design and workmanship)	-	1000	/
CLAUSE 5(Dimensions)	-	1000	/
CLAUSE 6(SURFACE PERFORMANCE)	-	5000	/
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	8000	/
CLAUSE 7(SAFETY TESTS)	-	1000	/
CLAUSE 7.3(Stability Test)	-	1000	/
CLAUSE 7.4(Vertical Static Load Tests)	-	1000	/
CLAUSE 7.5(Horizontal Static Load Tests)	-	1000	/
CLAUSE 7.5.2(Horizontal Static Load Test of Beds Without Headboard)	-	1000	/
CLAUSE 7.6.1(Vertical Durability Test of Bed Base)	-	5000	/
CLAUSE 7.6.2(Horizontal Durability Test of Bed Frame)	-	5000	/
CLAUSE 7.6.3(Horizontal Durability Test of Headboards)	-	8000	/
CLAUSE 7.7(Vertical Impact Test)	-	1000	/
CLAUSE 8.1(Mechanisms for Lifting Bed Bases)	-	3000	/
CLAUSE 8.2(Extendable Storage Elements)	-	2500	/

-
Included w.e.f 18.10.2024

147

IS 17633 (2022)

Tables and Desks - Specification

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 4(Design and workmanship)	-	1000	/
ClAUSE 5(Dimensions)	-	500	/
CLAUSE 6(SURFACE PERFORMANCE REQUIRMENTS)	-	7000	/
CLAUSE 7.2.1(Stability Under Vertical Load)	-	1000	/
CLAUSE 7.2.1.1(Test for tables that can be set to a height of 950 mm or less)	-	1000	/
CLAUSE 7.2.1.2(" Test for Tables that can be set to a height greater than 950 mm")	-	1000	/
CLAUSE 7.2.2(Stability with Extension Elements Open Place the table on the floor surface)	-	1000	/
CLAUSE 7.2.3(Stability Under Horizontal Load)	-	1000	/
CLAUSE 7.2.3.1(Test for tables that can be set to a height of 950 mm or less)	-	1000	/
CLAUSE 7.2.3.2(" Test for Tables that can be set to a height greater than 950 mm")	-	1000	/
CLAUSE 7.3.1(Strength under Vertical Static Force)	-	1000	/
CLAUSE 7.3.1.1(Stated load)	-	1000	/
CLAUSE 7.3.1.2(For occasional heavy loads)	-	1000	/
CLAUSE 7.3.2(Strength under horizontal static force)	-	1000	/
CLAUSE 7.4.1(Durability under Vertical Force)	-	6000	/
CLAUSE 7.4.2(Durability of the Height Adjustment Mechanism)	-	3000	/
CLAUSE 7.5.1(Durability and Stiffness Under Horizontal Force)	-	5000	/
CLAUSE 7.5.2(Durability under Horizontal Force)	-	3000	/
CLAUSE 7.5.3(Stiffness of the Structure Under Horizontal Force)	-	1000	/
CLAUSE 7.6.1(Vertical Impact Test)	-	1000	/
CLAUSE 7.6.2(Vertical Impact Test for Glass Table Tops)	-	1000	/
CLAUSE 7.6.3(Vertical Impact Test for All Other Table Tops)	-	1000	/
CLAUSE 7.7(Deflection of Table Tops)	-	1000	/
CLAUSE 7.8(Durability of Tables with Castors)	-	2000	/
CLAUSE 7.9(Drop Test)	-	1000	/
CLAUSE 4(Design and workmanship)	-	-	-
ClAUSE 5(Dimensions)	-	-	-
CLAUSE 6(SURFACE PERFORMANCE REQUIRMENTS)	-	-	-
CLAUSE 7.2.1(Stability Under Vertical Load)	-	-	-
CLAUSE 7.2.1.1(Test for tables that can be set to a height of 950 mm or less)	-	-	-
CLAUSE 7.2.1.2(" Test for Tables that can be set to a height greater than 950 mm")	-	-	-
CLAUSE 7.2.2(Stability with Extension Elements Open Place the table on the floor surface)	-	-	-
CLAUSE 7.2.3(Stability Under Horizontal Load)	-	-	-
CLAUSE 7.2.3.1(Test for tables that can be set to a height of 950 mm or less)	-	-	-
CLAUSE 7.2.3.2(" Test for Tables that can be set to a height greater than 950 mm")	-	-	-
CLAUSE 7.3.1(Strength under Vertical Static Force)	-	-	-
CLAUSE 7.3.1.1(Stated load)	-	-	-
CLAUSE 7.3.1.2(For occasional heavy loads)	-	-	-
CLAUSE 7.3.2(Strength under horizontal static force)	-	-	-
CLAUSE 7.4.1(Durability under Vertical Force)	-	-	-
CLAUSE 7.4.2(Durability of the Height Adjustment Mechanism)	-	-	-
CLAUSE 7.5.1(Durability and Stiffness Under Horizontal Force)	-	-	-
CLAUSE 7.5.2(Durability under Horizontal Force)	-	-	-
CLAUSE 7.5.3(Stiffness of the Structure Under Horizontal Force)	-	-	-
CLAUSE 7.6.1(Vertical Impact Test)	-	-	-
CLAUSE 7.6.2(Vertical Impact Test for Glass Table Tops)	-	-	-
CLAUSE 7.6.3(Vertical Impact Test for All Other Table Tops)	-	-	-
CLAUSE 7.7(Deflection of Table Tops)	-	-	-
CLAUSE 7.8(Durability of Tables with Castors)	-	-	-
CLAUSE 7.9(Drop Test)	-	-	-

-
Included w.e.f 18.10.2024

148

IS 17632 (2022)

General Purpose Chairs and Stools - Specification

78000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
CLAUSE 5(DIMENSIONS)	-	2000	/
CLAUSE 6(SURFACE PERFORMANCE)	-	7000	/
CLAUSE 6.2(Fabric and Leather (Synthetic and Natural) Performance)	-	22000	/
CLAUSE 7.2.1(Forwards Overbalancing and Sideways Overbalancing for Chairs without Arms)	-	1000	/
CLAUSE 7.2.2(Rearwards Overbalancing)	-	1000	/
CLAUSE 7.2.3(Sideways Overbalancing for Chairs with Arms)	-	1000	/
CLAUSE 7.2.4(Sideways Overbalancing for Chairs with Arms)	-	1000	/
CLAUSE 7.3.1.1(Seat static load test)	-	2000	/
CLAUSE 7.3.1.2(Back static load test)	-	2000	/
CLAUSE 7.3.1.3(Armrests/Wings sideways static load test)	-	2000	/
CLAUSE 7.3.1.4(Arm downwards static load test)	-	2000	/
CLAUSE 7.3.1.5(Leg forward static load test)	-	2000	/
CLAUSE 7.3.1.6(Leg sideways static load test)	-	2000	/
CLAUSE 7.3.1.7(Diagonal base load test)	-	2000	/
CLAUSE 7.3.1.8(Foot rest static-load test)	-	2000	/
CLAUSE 7.3.2.1(Seat impact test)	-	2000	/
CLAUSE 7.3.2.2(Back impact test)	-	2000	/
CLAUSE 7.3.2.3(Arm impact test)	-	2000	/
CLAUSE 7.3.2.4(Drop test)	-	2000	/
CLAUSE 7.4.1(Seat Fatigue Test)	-	20000	/
CLAUSE 7.4.2(Back Fatigue Test)	-	20000	/
CLAUSE 7.4.3(Arm Rest Durability Test)	-	20000	/

-
Included w.e.f 18.10.2024

149

IS 17631 (2022)

Work Chairs - Specification

79500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
clause 4(DESIGN AND WORKMANSHIP)	-	2000	/
clause 5(DIMENSIONS)	-	2000	/
Cl-6.1 (a)(Resistance to mechanical damage)	-	10000	/
Cl-6.1 (b)(Pencil hardness)	-	1000	/
Cl-6.1 (c)(Resistance to wet heat;)	-	1000	/
Cl-6.1 (d)(Resistance to dry heat;)	-	1000	/
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	1000	/
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	1000	/
Cl-6.1 (g)(Adhesive performance)	-	1000	/
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	1000	/
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	1000	/
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	1000	/
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	2000	/
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	1000	/
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	1000	/
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	1000	/
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	1000	/
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	1000	/
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	1000	/
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	1000	/
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	1000	/
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	1000	/
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	1000	/
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	1000	/
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	1000	/
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	1000	/
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	1000	/
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	1000	/
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	1000	/
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	1000	/
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	1000	/
Cl-7.3.1(Front Edge Overturning)	-	1000	/
Cl-7.3.2(Forwards Overturning)	-	1000	/
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	1000	/
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	1000	/
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	1000	/
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	1000	/
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	1000	/
Cl-7.4.1(Seat Front Edge Static Load Test)	-	2000	/
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	2000	/
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	2000	/
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	2000	/
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	2000	/
Cl-7.4.6(Foot Rest Static Load Test)	-	2000	/
Cl-7.5.1(Seat and Back Durability)	-	20000	/
Cl-7.5.2(Arm Rest Durability)	-	20000	/
Cl-7.5.3(Swivel Test)	-	20000	/
Cl-7.5.4(Foot-rest Durability)	-	20000	/
Cl-7.5.5(Castor and Chair-Base Durability)	-	20000	/
clause 4(DESIGN AND WORKMANSHIP)	-	2000	/
clause 5(DIMENSIONS)	-	2000	/
Cl-6.1 (a)(Resistance to mechanical damage)	-	1000	/
Cl-6.1 (b)(Pencil hardness)	-	1000	/
Cl-6.1 (c)(Resistance to wet heat;)	-	1000	/
Cl-6.1 (d)(Resistance to dry heat;)	-	1000	/
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	1000	/
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	1000	/
Cl-6.1 (g)(Adhesive performance)	-	1000	/
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	1000	/
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	1000	/
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	1000	/
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	2000	/
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	1000	/
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	1000	/
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	1000	/
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	1000	/
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	1000	/
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	1000	/
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	1000	/
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	1000	/
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	1000	/
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	1000	/
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	1000	/
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	1000	/
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	1000	/
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	1000	/
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	1000	/
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	1000	/
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	1000	/
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	1000	/
Cl-7.3.1(Front Edge Overturning)	-	1000	/
Cl-7.3.2(Forwards Overturning)	-	1000	/
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	1000	/
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	1000	/
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	1000	/
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	1000	/
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	1000	/
Cl-7.4.1(Seat Front Edge Static Load Test)	-	2000	/
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	2000	/
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	2000	/
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	2000	/
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	2000	/
Cl-7.4.6(Foot Rest Static Load Test)	-	2000	/
Cl-7.5.1(Seat and Back Durability)	-	20000	/
Cl-7.5.2(Arm Rest Durability)	-	20000	/
Cl-7.5.3(Swivel Test)	-	20000	/
Cl-7.5.4(Foot-rest Durability)	-	20000	/
Cl-7.5.5(Castor and Chair-Base Durability)	-	20000	/
clause 4(DESIGN AND WORKMANSHIP)	-	2000	/
clause 5(DIMENSIONS)	-	2000	/
Cl-6.1 (a)(Resistance to mechanical damage)	-	1000	/
Cl-6.1 (b)(Pencil hardness)	-	1000	/
Cl-6.1 (c)(Resistance to wet heat;)	-	1000	/
Cl-6.1 (d)(Resistance to dry heat;)	-	1000	/
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	1000	/
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	1000	/
Cl-6.1 (g)(Adhesive performance)	-	1000	/
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	1000	/
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	1000	/
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	1000	/
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	2000	/
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	1000	/
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	1000	/
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	1000	/
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	1000	/
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	1000	/
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	1000	/
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	1000	/
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	1000	/
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	1000	/
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	1000	/
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	1000	/
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	1000	/
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	1000	/
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	1000	/
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	1000	/
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	1000	/
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	1000	/
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	1000	/
Cl-7.3.1(Front Edge Overturning)	-	1000	/
Cl-7.3.2(Forwards Overturning)	-	1000	/
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	1000	/
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	1000	/
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	1000	/
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	1000	/
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	1000	/
Cl-7.4.1(Seat Front Edge Static Load Test)	-	2000	/
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	2000	/
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	2000	/
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	2000	/
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	2000	/
Cl-7.4.6(Foot Rest Static Load Test)	-	2000	/
Cl-7.5.1(Seat and Back Durability)	-	20000	/
Cl-7.5.2(Arm Rest Durability)	-	20000	/
Cl-7.5.3(Swivel Test)	-	20000	/
Cl-7.5.4(Foot-rest Durability)	-	20000	/
Cl-7.5.5(Castor and Chair-Base Durability)	-	20000	/
clause 4(DESIGN AND WORKMANSHIP)	-	0	/
clause 5(DIMENSIONS)	-	0	/
Cl-6.1 (a)(Resistance to mechanical damage)	-	0	/
Cl-6.1 (b)(Pencil hardness)	-	0	/
Cl-6.1 (c)(Resistance to wet heat;)	-	0	/
Cl-6.1 (d)(Resistance to dry heat;)	-	0	/
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	0	/
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	0	/
Cl-6.1 (g)(Adhesive performance)	-	0	/
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	0	/
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	0	/
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	0	/
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	0	/
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	0	/
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	0	/
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	0	/
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	0	/
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	0	/
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	0	/
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	0	/
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	0	/
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	0	/
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	0	/
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	0	/
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	0	/
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	0	/
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	0	/
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	0	/
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	0	/
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	0	/
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	0	/
Cl-7.3.1(Front Edge Overturning)	-	0	/
Cl-7.3.2(Forwards Overturning)	-	0	/
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	0	/
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	0	/
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	0	/
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	0	/
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	0	/
Cl-7.4.1(Seat Front Edge Static Load Test)	-	0	/
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	0	/
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	0	/
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	0	/
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	0	/
Cl-7.4.6(Foot Rest Static Load Test)	-	0	/
Cl-7.5.1(Seat and Back Durability)	-	0	/
Cl-7.5.2(Arm Rest Durability)	-	0	/
Cl-7.5.3(Swivel Test)	-	0	/
Cl-7.5.4(Foot-rest Durability)	-	0	/
Cl-7.5.5(Castor and Chair-Base Durability)	-	0	/
clause 4(DESIGN AND WORKMANSHIP)	-	0	/
clause 5(DIMENSIONS)	-	0	/
Cl-6.1 (a)(Resistance to mechanical damage)	-	0	/
Cl-6.1 (b)(Pencil hardness)	-	0	/
Cl-6.1 (c)(Resistance to wet heat;)	-	0	/
Cl-6.1 (d)(Resistance to dry heat;)	-	0	/
Cl-6.1 (e)(Resistance to marking by cold liquids)	-	0	/
Cl-6.1 (f)(Resistance to marking by cold oils and fats;)	-	0	/
Cl-6.1 (g)(Adhesive performance)	-	0	/
Cl-6.2 (a) (1)(For Fabric and Synthetic Leather:- Breaking load)	-	0	/
Cl-6.2 (a) (2)(For Fabric and Synthetic Leather:- Elongation at break)	-	0	/
Cl-6.2 (a) (3)(For Fabric and Synthetic Leather:- Tear strength)	-	0	/
Cl-6.2 (a) (4)(For Fabric and Synthetic Leather:- Colour fastness to light)	-	0	/
Cl-6.2 (a) (5)(For Fabric and Synthetic Leather:- Colour fastness to rubbing)	-	0	/
Cl-6.2 (a) (6)(For Fabric and Synthetic Leather:- Colour fastness to perspiration)	-	0	/
Cl-6.2 (a) (7)(For Fabric and Synthetic Leather:- Colour fastness to water)	-	0	/
Cl-6.2 (a) (8)(For Fabric and Synthetic Leather:- Pilling resistance)	-	0	/
Cl-6.2 (a) (9)(For Fabric and Synthetic Leather:- Coating adhesion strength)	-	0	/
Cl-6.2 (a) (10)(For Fabric and Synthetic Leather:- Seam slippage)	-	0	/
Cl-6.2 (a) (11)(For Fabric and Synthetic Leather:- Resistance to damage by flexing)	-	0	/
Cl-6.2 (a) (12)(For Fabric and Synthetic Leather:- Abrasion resistance)	-	0	/
Cl-6.2 (a) (13)(For Fabric and Synthetic Leather:- Bursting strength)	-	0	/
Cl-6.2 (a) (14)(For Fabric and Synthetic Leather:- Resistance to cold)	-	0	/
Cl-6.2 (b) (1)(For Natural Leather:- Tear strength)	-	0	/
Cl-6.2 (b) (2)(For Natural Leather:- Flexing endurance)	-	0	/
Cl-6.2 (b) (3)(For Natural Leather: Finish adhesion)	-	0	/
Cl-6.2 (b) (4)(For Natural Leather: Colour fastness to artificial light)	-	0	/
Cl-6.2 (b) (5)(For Natural Leather: Colour fastness to rubbing)	-	0	/
Cl-6.2 (b) (6)(For Natural Leather: Colour fastness to water spotting)	-	0	/
Cl-6.2 (b) (7)(For Natural Leather: Water vapour permeability)	-	0	/
Cl-6.2 (b) (8)(For Natural Leather: Colour fastness to water)	-	0	/
Cl-7.3.1(Front Edge Overturning)	-	0	/
Cl-7.3.2(Forwards Overturning)	-	0	/
Cl-7.3.3(Forwards Overturning for Chairs with Foot Rest)	-	0	/
Cl-7.3.4(Sideways Overturning for Chairs Without Arm Rests)	-	0	/
Cl-7.3.5(Sideways Overturning for Chairs With Arm Rests)	-	0	/
Cl-7.3.6(Rearwards Overturning for Chairs Without Back Rest Inclination)	-	0	/
Cl-7.3.7(Rearwards Overturning for Chairs with Backrest Inclination)	-	0	/
Cl-7.4.1(Seat Front Edge Static Load Test)	-	0	/
Cl-7.4.2(Combined Seat and Back Static Load Test)	-	0	/
Cl-7.4.3(Arm Rest Downward Static Load Test — Central)	-	0	/
Cl-7.4.4(Arm Rest Downward Static Load Test — Front)	-	0	/
Cl-7.4.5(Arm Rest Sideways Static Load Test)	-	0	/
Cl-7.4.6(Foot Rest Static Load Test)	-	0	/
Cl-7.5.1(Seat and Back Durability)	-	0	/
Cl-7.5.2(Arm Rest Durability)	-	0	/
Cl-7.5.3(Swivel Test)	-	0	/
Cl-7.5.4(Foot-rest Durability)	-	0	/
Cl-7.5.5(Castor and Chair-Base Durability)	-	0	/

-
Included w.e.f 18.10.2024

150

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	600	-
5(chemical composition)	-	2000	-
6.1 table 2(0.2% proof strength)	-	3000	-
6.1 table 2(tensile strength)	-	2500	-
6.1 table 2(Elongation)	-	2500	-
8(Dimensions & Tolerances)	-	1000	-
4(Freedom from defect)	-	-	-
5(chemical composition)	-	-	-
6.1 table 2(0.2% proof strength)	-	-	-
6.1 table 2(tensile strength)	-	-	-
6.1 table 2(Elongation)	-	-	-
8(Dimensions & Tolerances)	-	-	-

-
Incuded w.e.f. 17.05.2024

Bureau of Indian Standards

The National Standards Body of India

URS PRODUCTS AND TESTING PVT. LTD. (A29), NOIDA

A-29, Sector 5, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

9871062220 testing.a29@urs-labs.com

Scope List