BIS - LIMS (Laboratory Information Management System)

POWERONIC TEST & RESEARCH CENTRE PRIVATE LIMITED, GREATER NOIDA

First Floor, B-2/4, Site-B, UPSIDC Surajpur Industrial Area, Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201306

9602085835 info@poweroniclab.com

Scope List

Reset

73 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 996 (2009)

Single phase a.c. induction motors for general purpose (Third Revision)

Single phase a.c. induction motors for general purpose

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
16.1(Marking and Diagram of connenctions)	-	100	10 % Discount to BIS
10(Type of enclosures)	-	100	10 % Discount to BIS
9.1(General construction (as per Cl. 9 & F-3))	-	100	10 % Discount to BIS
4.1(Rated Voltage)	-	0	10 % Discount to BIS
4.3(Rated Output)	-	0	10 % Discount to BIS
4.4(Rated Speed)	-	0	10 % Discount to BIS
7(Dimensions (Cl.App.F-4))	-	150	10 % Discount to BIS
9.5(Earthing)	-	250	10 % Discount to BIS
17.3 (a)(No load test at rated voltage and frequency )	-	500	10 % Discount to BIS
12.1.1(Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-	500	10 % Discount to BIS
16.1(Marking and Diagram of connenctions)	-	0	10 % Discount to BIS
10(Type of enclosures)	-	0	10 % Discount to BIS
9.1(General construction (as per Cl. 9 & F-3))	-	0	10 % Discount to BIS
4.1(Rated Voltage)	-	0	10 % Discount to BIS
4.3(Rated Output)	-	0	10 % Discount to BIS
4.4(Rated Speed)	-	0	10 % Discount to BIS
7(Dimensions (Cl.App.F-4))	-	0	10 % Discount to BIS
9.5(Earthing)	-	0	10 % Discount to BIS
17.3 (a)(No load test at rated voltage and frequency )	-	0	10 % Discount to BIS
12.1.1(Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-	0	10 % Discount to BIS
12.1.1(Test for Breakaway starting current at rated voltage and frequency (Cl.12.1.1 & Cl. 12.5))	-	250	10 % Discount to BIS
12.5.1(Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-	250	10 % Discount to BIS
12.2(Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-	3000	10 % Discount to BIS
13.1(High voltage test)	-	1000	10 % Discount to BIS
13.2(Moisture proofness)	-	100	10 % Discount to BIS
13.3(Leakage current test)	-	500	10 % Discount to BIS
12.6(Vibration Severity)	-	200	10 % Discount to BIS
15.1(ADDITIONAL TESTS (For ECO - MARK))	-	0	10 % Discount to BIS
15.1.5(Noise Level)	-	750	10 % Discount to BIS
17.3 (g)(Insulation Resistance)	-	750	10 % Discount to BIS
16.1(Marking and Diagram of connenctions)	-	0	-
10(Type of enclosures)	-	0	-
9.1(General construction (as per Cl. 9 & F-3))	-	0	-
4.1(Rated Voltage)	-	0	-
4.3(Rated Output)	-	0	-
4.4(Rated Speed)	-	0	-
7(Dimensions (Cl.App.F-4))	-	0	-
9.5(Earthing)	-	0	-
17.3 (a)(No load test at rated voltage and frequency )	-	0	-
12.1.1(Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-	0	-
12.1.1(Test for Breakaway starting current at rated voltage and frequency (Cl.12.1.1 & Cl. 12.5))	-	0	-
12.5.1(Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-	0	-
12.2(Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-	0	-
13.1(High voltage test)	-	0	-
13.2(Moisture proofness)	-	0	-
13.3(Leakage current test)	-	0	-
12.6(Vibration Severity)	-	0	-
15.1(ADDITIONAL TESTS (For ECO - MARK))	-	0	-
17.3 (g)(Insulation Resistance)	-	0	-
9(General construction (as per Cl. 9 & F-3))	-	0	-
9.4.13(General construction (as per Cl. 9 & F-3))	-	0	-
12.7(Insulation resistance test)	-	0	-
15.1.5(Noise Level)	-	0	-
16.1(Marking and Diagram of connenctions)	-	0	-
10(Type of enclosures)	-	0	-
9.1(General construction (as per Cl. 9 & F-3))	-	0	-
4.1(Rated Voltage)	-	0	-
4.3(Rated Output)	-	0	-
4.4(Rated Speed)	-	0	-
7(Dimensions (Cl.App.F-4))	-	0	-
9.5(Earthing)	-	0	-
17.3 (a)(No load test at rated voltage and frequency )	-	0	-
12.1.1(Test for torques at rated voltage and frequency (Cl.12.1.1 & F-6.2 ))	-	0	-
12.1.1(Test for Breakaway starting current at rated voltage and frequency (Cl.12.1.1 & Cl. 12.5))	-	0	-
12.5.1(Full load performance at rated voltage and frequency (Cl.12.5 & F-6.2.4 ))	-	0	-
12.2(Temperature-rise test (Cl.12.2 & Cl.F-6.2.5))	-	0	-
13.1(High voltage test)	-	0	-
13.2(Moisture proofness)	-	0	-
13.3(Leakage current test)	-	0	-
12.6(Vibration Severity)	-	0	-
15.1(ADDITIONAL TESTS (For ECO - MARK))	-	0	-
17.3 (g)(Insulation Resistance)	-	0	-
9(General construction (as per Cl. 9 & F-3))	-	0	-
9.4.13(General construction (as per Cl. 9 & F-3))	-	0	-
12.7(Insulation resistance test)	-	0	-
15.1.5(Noise Level)	-	0	-

11 Apr, 2028

-
Included w.e.f. 08-08-2022.

IS 555 (1979)

Specification for electric table type fans and regulators (Third Revision)

Specification for electric table type fans and regulato

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.16(Creepage Distances and Clearances)	-	500	10 % Discount to BIS
10.14(Cord Grip Test)	-	700	10 % Discount to BIS
10.13, 7.4(Mechanical Endurance Test (for Regulators Only))	-	750	10 % Discount to BIS
10.12(Moisture Resistance Test)	-	1000	10 % Discount to BIS
10.11(Protection against Electric Shock)	-	500	10 % Discount to BIS
10.1(Earthing Connection)	-	500	10 % Discount to BIS
10.9(Fan Speed and Input)	-	500	10 % Discount to BIS
10.8(Construction)	-	300	10 % Discount to BIS
10.7(Insulation-Resistance Test (Shall follow Moisture Resistance Test Cl.10.12))	-	750	10 % Discount to BIS
10.6(High Voltage Test)	-	1000	10 % Discount to BIS
10.5(Leakage Current)	-	750	10 % Discount to BIS
10.4(Temperature-Rise Test)	-	2000	10 % Discount to BIS
10.3(Air Delivery Test)	-	3000	10 % Discount to BIS
9.0(Marking)	-	300	10 % Discount to BIS
7.11(Oscillating Mechanism)	-	500	10 % Discount to BIS
7.9(Interchangeability)	-	200	10 % Discount to BIS
7.8(Speed Regulators)	-	600	10 % Discount to BIS
6.0(Design and General Construction)	-	750	10 % Discount to BIS
5.0(Rated Frequency)	-	100	10 % Discount to BIS
4.0(Rated Voltages)	-	100	10 % Discount to BIS
3.0(Size, Speed and Types)	-	200	10 % Discount to BIS

11 Apr, 2028

-
Included w.e.f. 08-08-2022.

IS 191 (2007)

Copper - Specification (Fourth Revision)

For all Grades

6200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	0	-
4-Table 1(GRADES/DESIGNATIONS)	-	0	-
5.1- Table 2(L)	-	0	-
5.1- Table 2(L1)	-	0	-
5.1- Table 2(h)	-	0	-
5.1- Table 2(h1)	-	0	-
5.1- Table 2(b)	-	0	-
5.1- Table 2(b1)	-	0	-
5.1- Table 2(R)	-	0	-
5.1- Table 2(R1)	-	0	-
5.1- Table 2(R2 )	-	0	-
5.1- Table 2(α )	-	0	-
5.1- Table 2( β )	-	0	-
5.1- Table 2(γ)	-	0	-
5.2(Billets)	-	0	-
5.4-Table 3 (For Billets)(Mass)	-	0	-
5.2-Table 3 (For Billets)(Diameter)	-	0	-
5.2-Table 3 (For Billets)(Length)	-	0	-
5.2-Table 3 (For Billets)(Deviation from straightness per 1000 mm length)	-	0	-
5.4-Table 3 (Vertically continuously cast wire bars)(Mass)	-	0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Width)	-	0	-
5.3-Table 3 (Vertically continuously cast wire bars)(thickness )	-	0	-
5.3-Table 3 (Vertically continuously cast wire bars)(Other dimention)	-	0	-
5.4-Table 3 (Vertically static cast wire bars)(Mass)	-	0	-
5.3-Table 3 (Vertically static cast wire bars)(Width)	-	0	-
5.3-Table 3 (Vertically static cast wire bars)(thickness )	-	0	-
5.3-Table 3 (Vertically static cast wire bars)(Other dimention)	-	0	-
5.4-Table 3 (Ingots)(Mass)	-	0	-
5.4-Table 3 (Cast cakes)(Mass)	-	0	-
5.3-Table 3 (Cast cakes)(Width)	-	0	-
5.3-Table 3 (Cast cakes)(thickness )	-	0	-
5.3-Table 3 (Cast cakes)(Deviation from straightness per 1000 mm length)	-	0	-
7.1 - Table 4(Copper + Silver(By difference)-IS440)	-	100	-
7.1 - Table 4(Silver- IS 440)	-	100	-
7.1 - Table 4(Copper (any Silver present to be counted as copper)-IS440)	-	3000	-
7.1 - Table 4(Phosphorus- IS 440)	-	200	-
7.1 - Table 4(Arsenic- IS440)	-	200	-
7.1 - Table 4(Antimony-IS440)	-	200	-
7.1 - Table 4(Bismuth-IS 440)	-	200	-
7.1 - Table 4(Iron IS 440)	-	200	-
7.1 - Table 4(Lead IS 440)	-	200	-
7.1 - Table 4(Nickel IS 440)	-	200	-
7.1 - Table 4(Oxygen IS 440)	-	200	-
7.1 - Table 4(Selenium - IS 440)	-	200	-
7.1 - Table 4(Sulphur- IS 440)	-	200	-
7.1 - Table 4(Tellurium- IS 440)	-	200	-
7.1 - Table 4(Tin - IS 440)	-	200	-
7.1 - Table 4(Znic-IS 440)	-	200	-
7.1 - Table 4(Selenium + Telluuium- IS 440)	-	200	-
7.1 - Table 4(Total Impurities- IS 440)	-	200	-
8.1(FREEDOM FROM DEFECTS)	-	0	-
8.2(FREEDOM FROM DEFECTS)	-	0	-
9.1- Table 5(Mass Resistivity- IS 3635)	-	0	-
10(HYDROGEN EMBRITTLEMENT TEST- IS 191)	-	0	-
9.1 , 9.2 & 10(Resistivity & HYDROGEN EMBRITTLEMENT TEST)	-	0	-

11 Apr, 2028

-
Included w.e.f. 08-08-2022.

IS 14494 (2019)

Elastomer insulated flexible cables for use in mines - Specification (First Revision)

Elastomer insulated flexible cables for use in mines -

54000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	500	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	500	-
11.2 b)(ARMOURING: Elongation )	-	500	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	500	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	500	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	0	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
11.2 b)(ARMOURING: Elongation )	-	0	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	0	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	0	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	0	-
16.2(INSULATION : Thickness of Insulation)	-	250	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	250	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	0	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
11.2 b)(ARMOURING: Elongation )	-	0	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	0	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	0	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	0	-
16.2(INSULATION : Thickness of Insulation)	-	500	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	500	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
17.4(INSULATION SCREEN)	-	0	-
18(PROTECTIVE SCREEN)	-	0	-
19(CONDUCTANCE OF SCREEN)	-	1000	-
19.1(Individual Core Screen)	-	0	-
19.2(Collective Screen)	-	0	-
20.1(CORE IDENTIFICATION)	-	0	-
20.2(Colour Scheme for Identification)	-	0	-
20.3(Scheme for Identification by Numbering)	-	0	-
21.1(LAYING UP OF CORES)	-	0	-
21.2(LAYING UP OF CORES)	-	0	-
21.3(LAYING UP OF CORES)	-	0	-
21.4(LAYING UP OF CORES)	-	0	-
22.1(INNER SHEATH)	-	0	-
22.2(Thickness of Inner Sheath)	-	500	-
22.3(INNER SHEATH)	-	0	-
23.1(ARMOURING)	-	0	-
23.2(ARMOURING)	-	0	-
23.3(ARMOURING)	-	0	-
23.4(ARMOURING)	-	0	-
24.1(OUTER SHEATH)	-	0	-
24.2(Thickness of Outer Sheath)	-	500	-
24.3(Tolerance on Thickness of Outer Sheath)	-	500	-
24.4(OUTER SHEATH)	-	0	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	0	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
11.2 b)(ARMOURING: Elongation )	-	0	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	0	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	0	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	0	-
16.2(INSULATION : Thickness of Insulation)	-	0	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	0	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
17.4(INSULATION SCREEN)	-	0	-
18(PROTECTIVE SCREEN)	-	0	-
19(CONDUCTANCE OF SCREEN)	-	0	-
19.1(Individual Core Screen)	-	0	-
19.2(Collective Screen)	-	0	-
20.1(CORE IDENTIFICATION)	-	0	-
20.2(Colour Scheme for Identification)	-	0	-
20.3(Scheme for Identification by Numbering)	-	0	-
21.1(LAYING UP OF CORES)	-	0	-
21.2(LAYING UP OF CORES)	-	0	-
21.3(LAYING UP OF CORES)	-	0	-
21.4(LAYING UP OF CORES)	-	0	-
22.1(INNER SHEATH)	-	0	-
22.2(Thickness of Inner Sheath)	-	0	-
22.3(INNER SHEATH)	-	0	-
23.1(ARMOURING)	-	0	-
23.2(ARMOURING)	-	0	-
23.3(ARMOURING)	-	0	-
23.4(ARMOURING)	-	0	-
24.1(OUTER SHEATH)	-	0	-
24.2(Thickness of Outer Sheath)	-	0	-
24.3(Tolerance on Thickness of Outer Sheath)	-	0	-
24.4(OUTER SHEATH)	-	0	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	500	-
27.8(Flammability Test)	-	1000	-
27.9(Water Absorption Test)	-	2000	-
28(IDENTIFICATION)	-	0	-
29.1(PACKING AND MARKING)	-	0	-
29.2(PACKING AND MARKING)	-	0	-
30(BIS CERTIFICATION MARKING)	-	0	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	5000	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	1000	-
Table 33(f)(Insulation resistance)	-	1000	-
Table 33(e)(Tear resistance on sheath)	-	2000	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	3000	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	3000	-
Table 33(e)(Permanent set on Sheath)	-	500	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	3000	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	3000	-
Table 33(e)(Elongation at break on Sheath)	-	750	-
Table 33(e)(Tensile strength on Sheath)	-	750	-
Table 33(d)(Ozone resistance on Insulation)	-	5000	-
Table 33(d)(Permanent set on Insulation)	-	500	-
Table 33(d)(Hot set on Insulation)	-	500	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	3000	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	3000	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	2000	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	2000	-
Table 33(d)(Elongation at break on Insulation)	-	500	-
Table 33(d)(Tensile strength on Insulation)	-	500	-
Table 33(c)(Resistivity of steel wire)	-	500	-
Table 33(b)(Diameter of armour wire)	-	500	-
Table 4(Copper purity test)	-	2000	-
Table 33(a)(Conductor resistance test)	-	750	-
Table 33(a)(Annealing test)	-	500	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	0	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
11.2 b)(ARMOURING: Elongation )	-	0	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	0	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	0	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	0	-
16.2(INSULATION : Thickness of Insulation)	-	0	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	0	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
17.4(INSULATION SCREEN)	-	0	-
18(PROTECTIVE SCREEN)	-	0	-
19(CONDUCTANCE OF SCREEN)	-	0	-
19.1(Individual Core Screen)	-	0	-
19.2(Collective Screen)	-	0	-
20.1(CORE IDENTIFICATION)	-	0	-
20.2(Colour Scheme for Identification)	-	0	-
20.3(Scheme for Identification by Numbering)	-	0	-
21.1(LAYING UP OF CORES)	-	0	-
21.2(LAYING UP OF CORES)	-	0	-
21.3(LAYING UP OF CORES)	-	0	-
21.4(LAYING UP OF CORES)	-	0	-
22.1(INNER SHEATH)	-	0	-
22.2(Thickness of Inner Sheath)	-	0	-
22.3(INNER SHEATH)	-	0	-
23.1(ARMOURING)	-	0	-
23.2(ARMOURING)	-	0	-
23.3(ARMOURING)	-	0	-
23.4(ARMOURING)	-	0	-
24.1(OUTER SHEATH)	-	0	-
24.2(Thickness of Outer Sheath)	-	0	-
24.3(Tolerance on Thickness of Outer Sheath)	-	0	-
24.4(OUTER SHEATH)	-	0	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	0	-
27.8(Flammability Test)	-	0	-
27.9(Water Absorption Test)	-	0	-
28(IDENTIFICATION)	-	0	-
29.1(PACKING AND MARKING)	-	0	-
29.2(PACKING AND MARKING)	-	0	-
30(BIS CERTIFICATION MARKING)	-	0	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	0	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	0	-
Table 33(f)(Insulation resistance)	-	0	-
Table 33(e)(Tear resistance on sheath)	-	0	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	0	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	0	-
Table 33(e)(Permanent set on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	0	-
Table 33(e)(Elongation at break on Sheath)	-	0	-
Table 33(e)(Tensile strength on Sheath)	-	0	-
Table 33(d)(Ozone resistance on Insulation)	-	0	-
Table 33(d)(Permanent set on Insulation)	-	0	-
Table 33(d)(Hot set on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 33(d)(Elongation at break on Insulation)	-	0	-
Table 33(d)(Tensile strength on Insulation)	-	0	-
Table 33(c)(Resistivity of steel wire)	-	0	-
Table 33(b)(Diameter of armour wire)	-	0	-
Table 4(Copper purity test)	-	0	-
Table 33(a)(Conductor resistance test)	-	0	-
Table 33(a)(Annealing test)	-	0	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	0	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
11.2 b)(ARMOURING: Elongation )	-	0	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	0	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	0	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	0	-
16.2(INSULATION : Thickness of Insulation)	-	0	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	0	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
17.4(INSULATION SCREEN)	-	0	-
18(PROTECTIVE SCREEN)	-	0	-
19(CONDUCTANCE OF SCREEN)	-	0	-
19.1(Individual Core Screen)	-	0	-
19.2(Collective Screen)	-	0	-
20.1(CORE IDENTIFICATION)	-	0	-
20.2(Colour Scheme for Identification)	-	0	-
20.3(Scheme for Identification by Numbering)	-	0	-
21.1(LAYING UP OF CORES)	-	0	-
21.2(LAYING UP OF CORES)	-	0	-
21.3(LAYING UP OF CORES)	-	0	-
21.4(LAYING UP OF CORES)	-	0	-
22.1(INNER SHEATH)	-	0	-
22.2(Thickness of Inner Sheath)	-	0	-
22.3(INNER SHEATH)	-	0	-
23.1(ARMOURING)	-	0	-
23.2(ARMOURING)	-	0	-
23.3(ARMOURING)	-	0	-
23.4(ARMOURING)	-	0	-
24.1(OUTER SHEATH)	-	0	-
24.2(Thickness of Outer Sheath)	-	0	-
24.3(Tolerance on Thickness of Outer Sheath)	-	0	-
24.4(OUTER SHEATH)	-	0	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	0	-
27.8(Flammability Test)	-	0	-
27.9(Water Absorption Test)	-	0	-
28(IDENTIFICATION)	-	0	-
29.1(PACKING AND MARKING)	-	0	-
29.2(PACKING AND MARKING)	-	0	-
30(BIS CERTIFICATION MARKING)	-	0	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	0	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	0	-
Table 33(f)(Insulation resistance)	-	0	-
Table 33(e)(Tear resistance on sheath)	-	0	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	0	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	0	-
Table 33(e)(Permanent set on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	0	-
Table 33(e)(Elongation at break on Sheath)	-	0	-
Table 33(e)(Tensile strength on Sheath)	-	0	-
Table 33(d)(Ozone resistance on Insulation)	-	0	-
Table 33(d)(Permanent set on Insulation)	-	0	-
Table 33(d)(Hot set on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 33(d)(Elongation at break on Insulation)	-	0	-
Table 33(d)(Tensile strength on Insulation)	-	0	-
Table 33(c)(Resistivity of steel wire)	-	0	-
Table 33(b)(Diameter of armour wire)	-	0	-
Table 4(Copper purity test)	-	0	-
Table 33(a)(Conductor resistance test)	-	0	-
Table 33(a)(Annealing test)	-	0	-
27.2(Bending test followed by partial discharge test;)	-	0	-
27.4(Dielectric power factor test)	-	0	-
27.5(Heating cycle test followed by partial discharge test;)	-	0	-
27.6(Impulse voltage test; and)	-	0	-
4(CONDUCTOR)	-	0	-
5(INSULATION)	-	0	-
5.1(Power Cores)	-	0	-
5.2(Pilot and Earth Cores)	-	0	-
6(SEMI-CONDUCTING COMPOUND)	-	0	-
7.1(TAPE : Proofed Tape)	-	0	-
7.2(TAPE : Polyethylene Terephalate (PETP) or Polypropylene Base Tape)	-	0	-
7.3(TAPE )	-	0	-
8(CENTRE)	-	0	-
9.2(FILLERS)	-	0	-
10(CRADLE SEPARATOR)	-	0	-
11.1(ARMOUR)	-	0	-
11.2(ARMOUR)	-	0	-
11.2 a)(ARMOURING: Tensile Strength)	-	0	-
11.2 c)(ARMOURING: Torsion Test (For round wire ) )	-	0	-
11.2 b)(ARMOURING: Elongation )	-	0	-
11.2 d)(ARMOURING: Uniformity of zinc coating)	-	0	-
11.2 e)(ARMOURING: Mass of zinc coating )	-	0	-
12.1(SHEATH : Inner Sheath)	-	0	-
12.2(SHEATH : Outer Sheath)	-	0	-
13.1(REINFORCEMENT MATERIAL : Tape)	-	0	-
13.2(REINFORCEMENT MATERIAL : Cord/Yarns)	-	0	-
14.1(CONSTRUCTION : CONDUCTOR)	-	0	-
14.2(CONSTRUCTION : CONDUCTOR)	-	0	-
14.3(CONSTRUCTION : CONDUCTOR)	-	0	-
14.4(CONSTRUCTION : CONDUCTOR)	-	0	-
15(CONDUCTOR SCREENING)	-	0	-
16.1(INSULATION)	-	0	-
16.2(INSULATION : Thickness of Insulation)	-	0	-
16.3(INSULATION : Tolerance on Insulation Thickness)	-	0	-
16.4(INSULATION : Application of Insulation)	-	0	-
16.5(INSULATION)	-	0	-
17.1(INSULATION SCREEN)	-	0	-
17.2(INSULATION SCREEN)	-	0	-
17.3(INSULATION SCREEN)	-	0	-
17.4(INSULATION SCREEN)	-	0	-
18(PROTECTIVE SCREEN)	-	0	-
19(CONDUCTANCE OF SCREEN)	-	0	-
19.1(Individual Core Screen)	-	0	-
19.2(Collective Screen)	-	0	-
20.1(CORE IDENTIFICATION)	-	0	-
20.2(Colour Scheme for Identification)	-	0	-
20.3(Scheme for Identification by Numbering)	-	0	-
21.1(LAYING UP OF CORES)	-	0	-
21.2(LAYING UP OF CORES)	-	0	-
21.3(LAYING UP OF CORES)	-	0	-
21.4(LAYING UP OF CORES)	-	0	-
22.1(INNER SHEATH)	-	0	-
22.2(Thickness of Inner Sheath)	-	0	-
22.3(INNER SHEATH)	-	0	-
23.1(ARMOURING)	-	0	-
23.2(ARMOURING)	-	0	-
23.3(ARMOURING)	-	0	-
23.4(ARMOURING)	-	0	-
24.1(OUTER SHEATH)	-	0	-
24.2(Thickness of Outer Sheath)	-	0	-
24.3(Tolerance on Thickness of Outer Sheath)	-	0	-
24.4(OUTER SHEATH)	-	0	-
25.1(CABLE CONSTRUCTION AND DIMENSIONS)	-	0	-
27.8(Flammability Test)	-	0	-
27.9(Water Absorption Test)	-	0	-
28(IDENTIFICATION)	-	0	-
29.1(PACKING AND MARKING)	-	0	-
29.2(PACKING AND MARKING)	-	0	-
30(BIS CERTIFICATION MARKING)	-	0	-
Table 33®, Annex E(Electric tset on semi-conducting screen)	-	0	-
Table 33(n), Cl. No. 27.7(High Voltage test for 4 hrs.)	-	0	-
Table 33(f)(Insulation resistance)	-	0	-
Table 33(e)(Tear resistance on sheath)	-	0	-
Table 33(e)(Oil resistance - Elongation on sheath)	-	0	-
Table 33(e)(Oil resistance - Tensile strength on sheath)	-	0	-
Table 33(e)(Permanent set on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Elongation on Sheath)	-	0	-
Table 33(e)(Ageing in air bomb - Tensile strength on Sheath)	-	0	-
Table 33(e)(Elongation at break on Sheath)	-	0	-
Table 33(e)(Tensile strength on Sheath)	-	0	-
Table 33(d)(Ozone resistance on Insulation)	-	0	-
Table 33(d)(Permanent set on Insulation)	-	0	-
Table 33(d)(Hot set on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air bomb - Tensile strength on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Elongation on Insulation)	-	0	-
Table 33(d)(Ageing in air oven - Tensile strength on Insulation)	-	0	-
Table 33(d)(Elongation at break on Insulation)	-	0	-
Table 33(d)(Tensile strength on Insulation)	-	0	-
Table 33(c)(Resistivity of steel wire)	-	0	-
Table 33(b)(Diameter of armour wire)	-	0	-
Table 4(Copper purity test)	-	0	-
Table 33(a)(Conductor resistance test)	-	0	-
Table 33(a)(Annealing test)	-	0	-
27.2(Bending test followed by partial discharge test;)	-	0	-
27.4(Dielectric power factor test)	-	0	-
27.5(Heating cycle test followed by partial discharge test;)	-	0	-
27.6(Impulse voltage test; and)	-	0	-

11 Apr, 2028

-
Only upto 5kV. Included w.e.f. 08-08-2022.

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

Aluminium conductors for overhead transmission purposes

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Freedom from Defects)	-	0	20 % Discount to BIS
7.1 Table-1(Dimensional measurement of wires)	-	1000	20 % Discount to BIS
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	1000	20 % Discount to BIS
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	20 % Discount to BIS
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	20 % Discount to BIS
9.1(Stranding)	-	0	20 % Discount to BIS
9.2 Table 3(Lay Ratio of stranded conductors)	-	500	20 % Discount to BIS
9.3(Direction of Lay)	-	0	20 % Discount to BIS
9.4(Multiple layers of wires)	-	0	20 % Discount to BIS
11(Packing and Marking)	-	0	20 % Discount to BIS
12.2 Table 1(Breaking Load Test- Before Stranding)	-	1000	20 % Discount to BIS
12.2 Table 1(Breaking Load Test- After Stranding)	-	1000	20 % Discount to BIS
12.3 Table 1(Elongation Test- Before Stranding)	-	500	20 % Discount to BIS
12.3 Table 1(Elongation Test- After Stranding)	-	1000	20 % Discount to BIS
12.4 Table 1(Resistance of Aluminium wire)	-	1000	20 % Discount to BIS
9.2(Lay Ratio 24 wire layer)	-	500	20 % Discount to BIS
9.2(Lay Ratio 18 wire layer)	-	500	20 % Discount to BIS
9.2(Lay Ratio 12 wire layer)	-	500	20 % Discount to BIS
9.2(Lay Ratio 3/6 wire layer)	-	500	20 % Discount to BIS
6.1(Freedom from Defects)	-	0	-
7.1 Table-1(Dimensional measurement of wires)	-	0	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	0	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	-
9.1(Stranding)	-	0	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	0	-
9.3(Direction of Lay)	-	0	-
9.4(Multiple layers of wires)	-	0	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	0	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	0	-
12.3 Table 1(Elongation Test- Before Stranding)	-	0	-
12.3 Table 1(Elongation Test- After Stranding)	-	0	-
12.4 Table 1(Resistance of Aluminium wire)	-	0	-
6.1(Freedom from Defects)	-	0	-
7.1 Table-1(Dimensional measurement of wires)	-	0	-
7.2.2 Table-2, Table-4(Calculated resistance of Stranded Conductor)	-	0	-
8.1(Joints in wires-Conductors Containing Seven Wires)	-	0	-
8.2(Joints in wires-Conductors Containing More Than Seven Wires)	-	0	-
9.1(Stranding)	-	0	-
9.2 Table 3(Lay Ratio of stranded conductors)	-	0	-
9.3(Direction of Lay)	-	0	-
9.4(Multiple layers of wires)	-	0	-
11(Packing and Marking)	-	0	-
12.2 Table 1(Breaking Load Test- Before Stranding)	-	0	-
12.2 Table 1(Breaking Load Test- After Stranding)	-	0	-
12.3 Table 1(Elongation Test- Before Stranding)	-	0	-
12.3 Table 1(Elongation Test- After Stranding)	-	0	-
12.4 Table 1(Resistance of Aluminium wire)	-	0	-

11 Apr, 2028

-
Included w.e.f. 08-08-2022.

IS 398 : Part 1 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 1 aluminium stranded conductors (Third Revision)

Aluminum conductors for overhead transmission purposes

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	1000	Complete test charges by considering all tests Rs 6000/- for ( 25 Sq. mm , 50 Sq. mm & 100 Sq. mm ) and 10000/- for ( 150 Sq. mm , 240 Sq. mm & 300 sq. mm ). ( 20 % Discount to BIS )
12.3, Table-1(Breaking load before stranding)	-	1000	Complete test charges by considering all tests Rs 6000/- for ( 25 Sq. mm , 50 Sq. mm & 100 Sq. mm ) and 10000/- for ( 150 Sq. mm , 240 Sq. mm & 300 sq. mm ). ( 20 % Discount to BIS )
12.3, Table-1(Breaking load after stranding)	-	1000	Complete test charges by considering all tests Rs 6000/- for ( 25 Sq. mm , 50 Sq. mm & 100 Sq. mm ) and 10000/- for ( 150 Sq. mm , 240 Sq. mm & 300 sq. mm ). ( 20 % Discount to BIS )
12.4(Wrapping test)	-	1000	Complete test charges by considering all tests Rs 6000/- for ( 25 Sq. mm , 50 Sq. mm & 100 Sq. mm ) and 10000/- for ( 150 Sq. mm , 240 Sq. mm & 300 sq. mm ). ( 20 % Discount to BIS )
12.5, Table 1(Resistance test)	-	1000	Complete test charges by considering all tests Rs 6000/- for ( 25 Sq. mm , 50 Sq. mm & 100 Sq. mm ) and 10000/- for ( 150 Sq. mm , 240 Sq. mm & 300 sq. mm ). ( 20 % Discount to BIS )
12.6, Table 3(Measurement of lay ratio)	-	1000	Complete test charges by considering all tests Rs 6000/- for ( 25 Sq. mm , 50 Sq. mm & 100 Sq. mm ) and 10000/- for ( 150 Sq. mm , 240 Sq. mm & 300 sq. mm ). ( 20 % Discount to BIS )
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	0	-
12.3, Table-1(Breaking load before stranding)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	0	-
12.4(Wrapping test)	-	0	-
12.5, Table 1(Resistance test)	-	0	-
12.6, Table 3(Measurement of lay ratio)	-	0	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	0	-
12.3, Table-1(Breaking load before stranding)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	0	-
12.4(Wrapping test)	-	0	-
12.5, Table 1(Resistance test)	-	0	-
12.6, Table 3(Measurement of lay ratio)	-	0	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	0	-
12.3, Table-1(Breaking load before stranding)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	0	-
12.4(Wrapping test)	-	0	-
12.5, Table 1(Resistance test)	-	0	-
12.6, Table 3(Measurement of lay ratio)	-	0	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	0	-
12.3, Table-1(Breaking load before stranding)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	0	-
12.4(Wrapping test)	-	0	-
12.5, Table 1(Resistance test)	-	0	-
12.6, Table 3(Measurement of lay ratio)	-	0	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	0	-
12.3, Table-1(Breaking load before stranding)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	0	-
12.4(Wrapping test)	-	0	-
12.5, Table 1(Resistance test)	-	0	-
12.6, Table 3(Measurement of lay ratio)	-	0	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-
12.2, Table-1(Measurement of diameter of individual aluminium wire)	-	0	-
12.3, Table-1(Breaking load before stranding)	-	0	-
12.3, Table-1(Breaking load after stranding)	-	0	-
12.4(Wrapping test)	-	0	-
12.5, Table 1(Resistance test)	-	0	-
12.6, Table 3(Measurement of lay ratio)	-	0	-
9.3(Stranding)	-	0	-
6(Freedom from defects)	-	0	-

11 Apr, 2028

-
Included w.e.f. 08-08-2022.

IS 2465 (1984)

Specification for cables for motor vehicles (Second Revision)

Cables for motor vehicles

22950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.2, 10.3, 11(Dimensions & thickness )	-	200	10% Discount to BIS
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	500	10% Discount to BIS
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	250	10% Discount to BIS
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	2000	10% Discount to BIS
4.2 & 12.1, (e), 1(Tensile strength at break)	-	500	10% Discount to BIS
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	2000	10% Discount to BIS
20.3(EFFECT OF LUBRICATING OIL)	-	2000	10% Discount to BIS
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	1000	10% Discount to BIS
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	1000	10% Discount to BIS
3 & 6(Persulphate Test)	-	250	10% Discount to BIS
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	1000	10% Discount to BIS
3 & 6(Diameter of wire(mm))	-	250	10% Discount to BIS
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	500	10% Discount to BIS
4.2 & 12.1, (e), 1(elongation test at break)	-	500	10% Discount to BIS
14(High Voltage Test)	-	5000	10% Discount to BIS
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	0	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	0	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	0	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	0	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	0	-
20.3(EFFECT OF LUBRICATING OIL)	-	0	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	0	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
3 & 6(Persulphate Test)	-	0	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	0	-
3 & 6(Diameter of wire(mm))	-	0	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	0	-
4.2 & 12.1, (e), 1(elongation test at break)	-	0	-
14(High Voltage Test)	-	0	-
7.1(Insulation)	-	0	-
7.3(Insulation)	-	0	-
8(Core Identification)	-	0	-
9(Laying up of cores)	-	0	-
10.1.1(Sheathing )	-	0	-
10.2(Sheathing )	-	0	-
3 & 6(Flexibility class)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
24.1(PACKING AND MARKING)	-	0	-
20.3(EFFECT OF BRAKE FLUID)	-	2000	-
20.3(EFFECT OF DIESEL)	-	2000	-
20.3(Increase in average diameter %)	-	2000	-
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	0	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	0	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	0	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	0	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	0	-
20.3(EFFECT OF LUBRICATING OIL)	-	0	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	0	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
3 & 6(Persulphate Test)	-	0	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	0	-
3 & 6(Diameter of wire(mm))	-	0	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	0	-
4.2 & 12.1, (e), 1(elongation test at break)	-	0	-
14(High Voltage Test)	-	0	-
7.1(Insulation)	-	0	-
7.3(Insulation)	-	0	-
8(Core Identification)	-	0	-
9(Laying up of cores)	-	0	-
10.1.1(Sheathing )	-	0	-
10.2(Sheathing )	-	0	-
3 & 6(Flexibility class)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
24.1(PACKING AND MARKING)	-	0	-
20.3(EFFECT OF BRAKE FLUID)	-	0	-
20.3(EFFECT OF DIESEL)	-	0	-
20.3(Increase in average diameter %)	-	0	-
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	0	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	0	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	0	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	0	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	0	-
20.3(EFFECT OF LUBRICATING OIL)	-	0	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	0	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
3 & 6(Persulphate Test)	-	0	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	0	-
3 & 6(Diameter of wire(mm))	-	0	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	0	-
4.2 & 12.1, (e), 1(elongation test at break)	-	0	-
14(High Voltage Test)	-	0	-
7.1(Insulation)	-	0	-
7.3(Insulation)	-	0	-
8(Core Identification)	-	0	-
9(Laying up of cores)	-	0	-
10.1.1(Sheathing )	-	0	-
10.2(Sheathing )	-	0	-
3 & 6(Flexibility class)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
24.1(PACKING AND MARKING)	-	0	-
20.3(EFFECT OF BRAKE FLUID)	-	0	-
20.3(EFFECT OF DIESEL)	-	0	-
20.3(Increase in average diameter %)	-	0	-
7.2, 10.3, 11(Dimensions & thickness )	-	0	-
4.2 & 12.1(Without Ageing For Insulation Tensile Strength (N/mm²))	-	0	-
3 & 6(Conductor resistance Test (ohm/km at 20˚c))	-	0	-
17.1(OZONE RESISTANCE TEST FOR IGNITION CABLES)	-	0	-
4.2 & 12.1, (e), 1(Tensile strength at break)	-	0	-
19.1(EFFECT OF OIL ON IGNITION CABLES)	-	0	-
20.3(EFFECT OF LUBRICATING OIL)	-	0	-
18.1(EFFECT OF HEAT ON FLEXIBILITY FOR IGNITION CABLES)	-	0	-
21.1(EFFECT OF COOLING ON FLEXIBILITY)	-	0	-
3 & 6(Persulphate Test)	-	0	-
16.1(CAPACITANCE TEST FOR PVC INSULATION IGNITION CABLE)	-	0	-
3 & 6(Diameter of wire(mm))	-	0	-
4.2 & 12.1, (f), 1(elongation at break (N/mm²))	-	0	-
4.2 & 12.1, (e), 1(elongation test at break)	-	0	-
14(High Voltage Test)	-	0	-
7.1(Insulation)	-	0	-
7.3(Insulation)	-	0	-
8(Core Identification)	-	0	-
9(Laying up of cores)	-	0	-
10.1.1(Sheathing )	-	0	-
10.2(Sheathing )	-	0	-
3 & 6(Flexibility class)	-	0	-
23.1(Manufacturer's Identification)	-	0	-
24.1(PACKING AND MARKING)	-	0	-
20.3(EFFECT OF BRAKE FLUID)	-	0	-
20.3(EFFECT OF DIESEL)	-	0	-
20.3(Increase in average diameter %)	-	0	-

11 Apr, 2028

-
Included w.e.f. 08-08-2022.

IS 302 : Part 2 : Sec 30 (2007)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 30 room heaters (First Revision)

Room Heater

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.8 & IS:302-1:2008(Protection Against Access to Live Parts)	-	500	-
Cl.10 & IS:302-1:2008(Power Input and Current)	-	300	-
Cl.11 & IS:302-1:2008(Heating)	-	500	-
Cl.13 & IS:302-1:2008(Leakage Current & Electric Strength at operating temp. )	-	500	-
Cl.14 & IS:302-1:2008(Transient Over Voltages)	-	500	-
Cl.15 & IS: 302-1:2008(Moisture Resistance )	-	500	-
Cl.15.3 of IS 302-1:200(Moisture Resistance )	-	500	-
Cl.16 & IS:302-1:2008(Leakage Current & Electric Strength )	-	500	-
Cl.17 & IS:302-1:2008(Over load Protection of Transformers and Associated Circuits )	-	500	-
Cl.18 (Endurance. )	-	1000	-
Cl.19 & IS:302-1:2008(Abnormal Operation.)	-	500	-
Cl.19.102(Abnormal Operation.)	-	0	-
Cl.19.103(Abnormal Operation.)	-	0	-
Cl.19.104(Abnormal Operation.)	-	0	-
Cl.19.105(Abnormal Operation.)	-	0	-
Cl.19.106(Abnormal Operation.)	-	0	-
Cl.19.107(Abnormal Operation.)	-	0	-
Table 8 of IS 302-1:2008(Abnormal Operation.)	-	0	-
Cl.19.108(Abnormal Operation.)	-	0	-
Cl.19.109(Abnormal Operation.)	-	0	-
Cl.19.110(Abnormal Operation.)	-	0	-
Cl.19.111(Abnormal Operation.)	-	0	-
Cl.19.112(Abnormal Operation.)	-	0	-
Cl.19.113(Abnormal Operation.)	-	0	-
Cl.19.114(Abnormal Operation.)	-	0	-
Cl.20 & IS:302-1:2008(Stability & Mechanical Hazards)	-	500	-
Cl.21 & IS:302-1:2008)(Mechanical Strength.)	-	250	-
Cl.21.2 of IS 302-1:2008(Mechanical Strength.)	-	250	-
Cl.21.103(Mechanical Strength.)	-	250	-
Cl.22.1 of IS 302-1:2008(Construction)	-	50	-
Cl.22.5 of IS 302-1:2008(Construction)	-	50	-
Cl.22.6 of IS 302-1:2008(Construction)	-	50	-
Cl.22.7 of IS 302-1:2008(Construction)	-	50	-
Cl.22.8 of IS 302-1:2008(Construction)	-	50	-
Cl.22.9 of IS 302-1:2008(Construction)	-	50	-
Cl.22.11(Construction)	-	50	-
Cl.22.12 of IS 302-1:2008(Construction)	-	50	-
Cl.22.13 of IS 302-1:2008(Construction)	-	50	-
Cl.22.14 of IS 302-1:2008(Construction)	-	50	-
Cl.22.15 of IS 302-1:2008(Construction)	-	50	-
Cl.22.18 of IS 302-1:2008(Construction)	-	50	-
Cl.22.20 of IS 302-1:2008(Construction)	-	50	-
Cl.22.21 of IS 302-1:2008(Construction)	-	50	-
Cl.23 & IS:302-1:2008(Internal Wiring )	-	250	-
Cl.23.4 & Cl.29 of 302-1:2008(Internal Wiring )	-	250	-
Cl.23.5 of 302-1:2008(Internal Wiring )	-	250	-
Cl.23.7 of 302-1:2008(Internal Wiring )	-	250	-
Cl.24.1 of 302-1:2008(Component)	-	50	-
Cl.24.1.3 (Component)	-	50	-
C.24.1.4(Component)	-	50	-
Cl.24.10(Component)	-	50	-
C.24.2 of 302-1:2008(Component)	-	50	-
Cl.25.1 of 302-1:2008(Supply Connection and External Flexible Cords )	-	50	-
Cl. 25.2 of IS 3021:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl. 25.3 of IS 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl. 25.4 of IS 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.5 of 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.6 of 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.7.(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.8(Supply Connection and External Flexible Cords )	-	100	-
Cl. 25.9(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.10 of 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl. 25.11(Supply Connection and External Flexible Cords )	-	100	-
Cl. 25.12(Supply Connection and External Flexible Cords )	-	100	-
Cl. 25.13(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.14 of IS 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.15 of IS 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.17 of IS 302-1:2008(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.18(Supply Connection and External Flexible Cords )	-	100	-
Cl.25.20(Supply Connection and External Flexible Cords )	-	100	-
Cl.26.1 of IS 302-1:2008(Terminal for External Conductors )	-	250	-
Cl.26.10 of IS 302-1:2008(Terminal for External Conductors )	-	250	-
Cl.26.11 of IS 302-1:2008(Terminal for External Conductors )	-	250	-
Cl.27.1 of 302-1:2008(Provision for Earthing.)	-	200	-
Cl.27.5 of 302-1:2008(Provision for Earthing.)	-	50	-
Cl.28 of 302-1:2008(Screws and Connections.)	-	250	-
Cl.29 & IS:302-1:2008(Clearances, Creepage Distances and Solid Insulation)	-	500	-
Cl.30 & IS:302-1:2008(Resistance to Heat and Fire)	-	2000	-
Cl.30.2 of 302-1:2008(Resistance to Heat and Fire : Resistance to fire)	-	0	-
Cl.31 of IS:302-1:2008(Resistance to Rusting.)	-	1000	-
Cl.30.1 of IS:302-1:2008(Resistance to Heat and Fire: Resistance to heat. )	-	0	-
Cl.31 & IS:302-1:2008(Resistance to Rusting.)	-	0	-
Cl.32 & IS:302-1:2008(Radition,Toxicity and similar Hazards.)	-	1000	-
Cl.6 (Classification)	-	250	-
Cl.7 & IS:302-1:2008(Marking and Instructions)	-	250	-
Cl.7 & IS:302-1:2008(Marking and Instructions)	-	0	-

11 Apr, 2028

-
EXCLUSIONS: EMI/EMC tests (Electrostatic discharges, radiant fields, fast transient bursts, voltage surges, injected current, voltage dip and interruption, mains signals) (Cl.19.11.4.1 to 19.11.4.7), Components (Capacitors for radio interference suppression, isolating transformer, coupler) (Cl.24.1.1, 24.1.2, 24.1.5

IS 302 : Part 2 : Sec 14 (2009)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 14 electric kitchen machines (First Revision)

Electric kitchen Machines

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8( Protection Against Electric Shock, IS 302-1)	-	500	-
10(Power Input and Current, IS 302-1)	-	500	-
11(Heating, IS 302-1)	-	1000	-
13(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	500	-
14(Transient Over Voltages, IS 302-1)	-	500	-
15.1(Moisture Resistance, IS 302-1)	-	500	-
16(Electrical Insulation and Leakage Current at Operating Temperature: Leakage current, IS 302-1)	-	500	-
17(Overload protection of Transformers and Associated Circuits, IS 302-1)	-	500	-
19.7(Abnormal Operation, IS 302-1)	-	1000	-
20.1(Stability & Mechanical Hazards, IS 302-1)	-	50	-
20.2(Stability & Mechanical Hazards, IS 302-1)	-	50	-
20.103(Stability & Mechanical Hazards)	-	50	-
20.104(Stability & Mechanical Hazards)	-	50	-
20.105(Stability & Mechanical Hazards)	-	50	-
20.106(Stability & Mechanical Hazards)	-	50	-
20.107(Stability & Mechanical Hazards)	-	50	-
20.108(Stability & Mechanical Hazards)	-	50	-
20.109(Stability & Mechanical Hazards)	-	50	-
20.110(Stability & Mechanical Hazards)	-	50	-
20.111(Stability & Mechanical Hazards)	-	50	-
20.113(Stability & Mechanical Hazards)	-	50	-
20.114(Stability & Mechanical Hazards)	-	50	-
20.115(Stability & Mechanical Hazards)	-	50	-
20.116(Stability & Mechanical Hazards)	-	50	-
21.1(Mechanical Strength, IS 302-1)	-	250	-
21.2(Mechanical Strength, IS 302-1)	-	250	-
22.101(Construction)	-	500	-
22.102(Construction)	-	500	-
23.1(Internal Wiring, IS 302-1)	-	200	-
23.2(Internal Wiring, IS 302-1)	-	200	-
23.3(Internal Wiring, IS 302-1)	-	200	-
23.4(Internal Wiring, IS 302-1)	-	200	-
23.5(Internal Wiring, IS 302-1)	-	200	-
23.6(Internal Wiring, IS 302-1)	-	200	-
23.7(Internal Wiring, IS 302-1)	-	200	-
23.8(Internal Wiring, IS 302-1)	-	200	-
23.9(Internal Wiring, IS 302-1)	-	200	-
23.10(Internal Wiring, IS 302-1)	-	200	-
24.1(Components, IS 302-1)	-	250	-
24.2(Components, IS 302-1)	-	250	-
24.5(Components, IS 302-1)	-	250	-
24.6(Components, IS 302-1)	-	250	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	1	-
25.5(Supply Connection and External Flexible Cords, IS 302-1)	-	1	-
25.6(Supply Connection and External Flexible Cords, IS 302-1)	-	1	-
25.7(Supply Connection and External Flexible Cords, IS 302-1)	-	1	-
25.8(Supply Connection and External Flexible Cords, IS 302-1)	-	1	-
26.9(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.1(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.11(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.12(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.13(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.14(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.15(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.16(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.17(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.18(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.19(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.2(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.21(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
25.22(Supply Connection and External Flexible Cords, IS 302-1)	-	50	-
26(Terminals for External Conductors, IS 302-1)	-	500	-
27(Provision for Earthing, IS 302-1)	-	100	-
27.2(Provision for Earthing, IS 302-1)	-	100	-
27.3(Provision for Earthing, IS 302-1)	-	100	-
27.4(Provision for Earthing, IS 302-1)	-	100	-
27.5(Provision for Earthing, IS 302-1)	-	100	-
28(Screws & Connections, IS 302-1)	-	500	-
29.1(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	-
29.2(Clearances, Creepage distances and Solid Insulation, IS 302-1)	-	250	-
30.1(Resistance to Heat and Fire, IS 302-1)	-	500	-
30.2(Resistance to Heat and Fire, IS 302-1)	-	500	-
31(Resistance of Rusting, IS 302-1)	-	500	-
32(Radiation, Toxicity and similar Hazard IS 302-1)	-	1500	-

11 Apr, 2028

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

rated voltage not exceeding 440 V and rated current not

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Rating)	-	500	-
6(Rating)	-	500	-
7(Classification)	-	500	-
8.2(Marking)	-	100	-
8.3(Marking)	-	100	-
8.4(Marking)	-	100	-
8.5(Marking)	-	150	-
8.6(Marking)	-	150	-
8.7(Marking)	-	150	-
8.8(Marking)	-	150	-
10(Protection against Electric Shock)	-	1000	-
11.1(Provision for earthing)	-	1000	-
12(Terminals)	-	100	-
12.2.1(Terminals)	-	100	-
12.2.2(Connection of conductor)	-	500	-
12.2.3(Mechanical strength of terminals)	-	500	-
12.2.4(Resistance to corrosion)	-	500	-
12.2.5(Undue damage to conductor)	-	500	-
12.2.7(Insertion of conductor)	-	100	-
12.2.9(Locking against accidental loosening)	-	100	-
12.2.11(Distance between screw and conductor)	-	100	-
12.3.2(Screwless terminals)	-	100	-
12.3.3(Connectin of conductor)	-	100	-
12.3.4(Material of terminals)	-	100	-
12.3.5(Clamping)	-	100	-
12.3.7(v) Interconnection of conductors [Cl. 12.3.7])	-	100	-
12.3.11(vi) Electrical & Thermal Stresses [Cl 12.3.11])	-	1000	-
12.3.12(vii) Deflection Stresses [Cl. 12.3.12])	-	150	-
13.1(a) Insulating lining, barriers and the like [Cl 13.1])	-	100	-
13.2(b) Construction of switch [Cl 13.2])	-	100	-
13.2(i) Installation Test)	-	100	-
13.3(c) Covers,cover plates and actuating members [Cl 13.3])	-	100	-
13.4(d) Ordinary switches [Cl 13.4])	-	100	-
13.5(e) Rotary switches [Cl 13.5])	-	100	-
13.6(f) Screws and other means [Cl 13.6])	-	100	-
13.7(g) Combination of switches or switches and socket outlets [Cl 13.7])	-	100	-
13.8(h) Assessories combined with switches [Cl. 13.8])	-	100	-
13.9(j) Switches other than ordinary switches [Cl. 13.9])	-	100	-
13.1(k) Switches to be installed in a box [Cl. 13.10])	-	100	-
13.11(l) Surface type switches other than ordinary switch [Cl. 13.11])	-	100	-
13.12, 13.13, 13.14(m) Inlet opening [Cl. 13.12.13.13 & 13.14])	-	100	-
13.15(q) Requirements for membrane in inlet opening [ Cl. 13.15])	-	100	-
14.4(Mechanism)	-	100	-
15.1(Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-	100	-
15.2(b)Resistance to Harmful ingress of water [Cl. 15.2])	-	100	-
15.3(c) Resistance to Humidity [Cl. 15.3])	-	100	-
16.1(Insulation resistance [Cl. 16.1])	-	100	-
16.2( Electric Strength [Cl. 16.2])	-	100	-
16.3(Insulation resistance and electric strength )	-	100	-
17(Temperature- rise [Cl. 17])	-	100	-
18(Marking and breaking Capacity[Cl. 18])	-	100	-
19(Normal Operation [Cl. 19] a) General & Operation)	-	100	-
19(b) Electric Strength)	-	100	-
19(c)Temperature-rise )	-	10	-
20(Mechanical Strength Test [Cl. 20])	-	10	-
21(Resistance to Heat [Cl.21])	-	10	-
22(Screw, Current Carrying Part And Connection [Cl.22])	-	10	-
22.1(i) Screw & Nuts [Cl.22.1])	-	10	-
22.4(ii) Screw & rivets [Cl . 22.4])	-	10	-
22.3(iii) Electrical Connections [Cl.22.3])	-	10	-
22.5(iv) Current carrying part [Cl.22.5])	-	10	-
23.1(Creepage distances, clearances & distance through sealing compound )	-	10	-
24.1.1(Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-	500	-
24.2(Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-	500	-
19.2(Normal operation)	-	10	-
25 of IS 3854 : 1997(Resistance to rusting)	-	500	-

11 Apr, 2028

-
-

IS 1293 (2019)

Plugs and socket - Outlets of rated Voltage up to and including 250 Volts and rated current up to and including 16 amperes - Specification (Third Revision)

up to 250 v and rated current up to including 16 Amp

17500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Ratings)	-	10	-
7.1.1(Accessories Classification)	-	10	-
7.1.2(Accessories Classification)	-	10	-
7.1.3(Accessories Classification)	-	10	-
7.1.4(Accessories Classification)	-	10	-
7.1.5(Accessories Classification)	-	10	-
8.1(MARKING)	-	10	-
8.8(MARKING)	-	10	-
8.9(MARKING)	-	10	-
9.1(CHECKING OF DIMENSIONS)	-	10	-
9.2(CHECKING OF DIMENSIONS)	-	10	-
10.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	250	-
10.1(PROTECTION AGAINST ELECTRIC SHOCK)	-	250	-
10.3(PROTECTION AGAINST ELECTRIC SHOCK)	-	10	-
10.4(PROTECTION AGAINST ELECTRIC SHOCK)	-	10	-
10.5(PROTECTION AGAINST ELECTRIC SHOCK)	-	10	-
10.6(PROTECTION AGAINST ELECTRIC SHOCK)	-	10	-
10.7(PROTECTION AGAINST ELECTRIC SHOCK)	-	10	-
11.1(PROVISIONS FOR EARTHING)	-	10	-
11.2(PROVISIONS FOR EARTHING)	-	10	-
12.1.1(TERMINALS)	-	10	-
12.1.2(TERMINALS)	-	10	-
12.2.2(TERMINALS)	-	10	-
12.2.3(TERMINALS)	-	10	-
12.2.4(TERMINALS)	-	10	-
12.2.5(TERMINALS)	-	10	-
12.2.6(TERMINALS)	-	10	-
12.2.7(TERMINALS)	-	10	-
12.2.8(TERMINALS)	-	10	-
12.3.9(TERMINALS)	-	10	-
12.3.10(TERMINALS)	-	10	-
12.3.11(TERMINALS)	-	10	-
12.3.12(TERMINALS)	-	10	-
13.1(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.2(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.3(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.4(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.5(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.6(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.7(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.8(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.9(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.1(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.11(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.12(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.13(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.15(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.16(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.17(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.18(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.19(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.21(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.22(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
13.23(CONSTRUCTIONS OF FIXED SOCKETOUTLETS)	-	10	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.3(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.4(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.5(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.16(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.7(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.8(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.9(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.1(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.11(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.12(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.13(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.14(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.15(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.17(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.18(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.19(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.2(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.21(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.22(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.23(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.24(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.25(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
14.26(CONSTRUCTION OF PLUGS AND PORTABLE SOCKET-OUTLET)	-	10	-
15(INTERLOCKED SOCKET-OUTLETS)	-	100	-
16.1(RESISTANCE TO AGEING,)	-	250	-
16.2(RESISTANCE TO HARMFUL INGRESS OF WATER AND TO HUMIDITY)	-	250	-
16.3(Resistance to Humidity)	-	250	-
17.1(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	250	-
17.2(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	350	-
17.3(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	400	-
18(OPERATION OF EARTHING CONTACTS)	-	500	-
19(TEMPERATURE RISE)	-	500	-
20(BREAKING CAPACITY)	-	500	-
21(NORMAL OPERATION)	-	500	-
22.1(Verification of the Maximum Withdrawal Force)	-	250	-
22.2(Verification of Minimum Withdrawal Force)	-	250	-
23.1(FLEXIBLE CABLES AND THEIR CONNECTION)	-	350	-
23.3(FLEXIBLE CABLES AND THEIR CONNECTION)	-	350	-
23.4(FLEXIBLE CABLES AND THEIR CONNECTION)	-	300	-
24.1(MECHANICAL STRENGTH For all kinds of fixed socket-outlets )	-	100	-
24.1(MECHANICAL STRENGTH For portable multiple and combined socket outlets with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	100	-
24.1(MECHANICAL STRENGTH For surface mounting boxes)	-	100	-
24.2(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	100	-
24.2(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	100	-
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies other than elastomeric or thermoplastic material)	-	200	-
24.2(MECHANICAL STRENGTH For plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	-
24.3(MECHANICAL STRENGTH for fixed socket-outlets with a main part intended to be mounted directly on a surface)	-	200	-
24.4(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	200	-
24.4(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	200	-
24.4(MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	10	-
24.5(MECHANICAL STRENGTH For portable single socket-outlets: 1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	100	-
24.5(MECHANICAL STRENGTH For portable multiple and combined socket outlets: 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	100	-
24.5(MECHANICAL STRENGTH For Plug 1) with enclosures, covers and bodies of elastomeric or thermoplastic material)	-	100	-
24.6(MECHANICAL STRENGTH For screwed glands of accessories having an IP code higher than IP20)	-	100	-
24.7(MECHANICAL STRENGTH For plug pins provided with insulating sleeves)	-	100	-
24.8(MECHANICAL STRENGTH For shuttered socket-outlets)	-	100	-
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	100	-
24.9(MECHANICAL STRENGTH For portable multiple and combined socket outlets (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	100	-
24.1(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies other than thermoplastic or elastomeric material)	-	100	-
24.1(MECHANICAL STRENGTH For Plug (1) with enclosures, covers or bodies of thermoplastic or elastomeric material)	-	100	-
24.11(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	100	-
24.12(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	100	-
24.13(MECHANICAL STRENGTH For portable socket-outlets having means for suspension on a wall)	-	100	-
24.14.1(MECHANICAL STRENGTH For fixed socket-outlets)	-	100	-
24.14.2(MECHANICAL STRENGTH For fixed socket-outlets)	-	100	-
24.14.3(MECHANICAL STRENGTH For plugs and portable socket-outlets)	-	100	-
25.1(RESISTANCE TO HEAT Accessories and surface mounting boxes)	-	100	-
25.2(RESISTANCE TO HEAT Parts of insulating material necessary to retain current-carrying parts of the earthing circuit in position, as well as parts of the front surface zone of thermoplastic material)	-	100	-
25.3(RESISTANCE TO HEAT Parts of insulating material not necessary to retain current-carrying parts and parts of the earthing circuit in position, even though they are in contact with them)	-	250	-
25.4(RESISTANCE TO HEAT )	-	250	-
26.2(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	10	-
26.1(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	100	-
26.3(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	100	-
26.4(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	100	-
26.5(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	100	-
26.6(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	300	-
26.7(SCREWS, CURRENT-CARRYING PARTS AND CONNECTIONS)	-	200	-
27.1(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	250	-
27.2(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	2	-
27.3(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH SEALING COMPOUND)	-	50	-
28.1.1(Resistance to Abnormal Heat and to Fire Glow-Wire Test)	-	3000	-
28.1.2(Resistance to Abnormal Heat and to Fire for plugs with pins provided with insulating sleeves)	-	1000	-
28.2(Resistance to Tracking For accessories other than IP code higher than IPX0 parts of insulating material retaining live parts in position)	-	1000	-
29(RESISTANCE TO RUSTING)	-	1000	-
30.1(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Pressure Test at High Temperature)	-	250	-
30.2(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Static Damp Heat Test)	-	250	-
30.3(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Tests at Low Temperature)	-	250	-
30.4(ADDITIONAL TESTS ON PINS PROVIDED WITH INSULATING SLEEVES Impact Test at Low Temperature)	-	250	-

11 Apr, 2028

-
-

IS 9857 (1990)

Welding cables - Specification (First Revision)

450/750 Volts

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1 a) 1)(Annealing test - IS 10810: Part 1)	-	500	-
10.1 a) 2)(Conductor resistance tes - IS 10810 : Part 5)	-	500	-
Table 1 (Thickness of covering)	-	500	-
10.1 c) 1)(Physical tests for covering : Tensile strength )	-	500	-
10.1 c) 1)(Physical tests for covering : Elongation at break )	-	500	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength )	-	500	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation at break )	-	500	-
10.1 c) 2)(Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-	500	-
10.1 c) 2)(Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-	500	-
Table 2(Ageing in air bomb - Elongation)	-	1000	-
Table 2(Ageing in air bomb - Tensile strength )	-	1000	-
Table 2(Oil resistance - Elongation)	-	1000	-
Table 2(Oil resistance - Tensile strength )	-	1000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Tensile strength variation )	-	1000	-
10.1 c) 4)(Physical tests for covering - Oil Resistance : Elongation variation at break )	-	1000	-
10.1 c) 5)(Hot set test )	-	500	-
11.1(High Voltage Test ( Water Immersion Test ))	-	2000	-
11.3(Static Flexibility Test)	-	500	-
11.4(Flammability Test)	-	2000	-
4(Conductor : Material )	-	0	-
5(SEPARATOR)	-	0	-
6(COVERING)	-	0	-
7(CONDUCTOR : CONSTRUCTION )	-	0	-
8(S E P A R A T O R)	-	0	-
9.1(C O V E R I N G : Application )	-	0	-
9.2(T h i c k n e s s o f C o v e r i n g)	-	0	-
9.3(T o l e r a n c e on Thickness o f C o v e r i n g)	-	0	-
9.4(A p p l i c a t i o n of C o v e r i n g)	-	0	-
9.5(Colour of C o v e r i n g)	-	0	-
12.1(Manufacturer's Identification)	-	0	-
12.2(Cable Identification)	-	0	-
12.3(Cable Code)	-	0	-
13.2(Marking)	-	0	-
Table 4(Copper purity test)	-	1500	-

11 Apr, 2028

-
-

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

for rated voltages up to & including 450/750 V

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.6(Halogen evolution)	-	100	-
10.7(Temperature index)	-	100	-
Table 1 iii) c) 3)(Elongation (After ageing))	-	100	-
Table 1 iii) c) 3)(Tensile strength (After ageing))	-	100	-
Table 1 iii) c) 1)(Elongation (Without ageing))	-	100	-
Table 1 iii) c) 1)(Tensile strength (Without ageing))	-	100	-
4.1(Annealing test (for copper))	-	400	-
Table 1 iii) d) 2)(Loss of mass- Sheath )	-	50	-
Table 1 iii) c) 2)(Loss of mass- Insulation )	-	400	-
Table 1 iii) d) 4)(Shrinkage- Sheath )	-	400	-
Table 1 iii) c) 4)(Shrinkage-Insulation)	-	400	-
Table 1 iii) d) 6)(Hot deformation -Indentation depth - Sheath )	-	400	-
Table 1 iii) c) 6)(Hot deformation - Indentation depth- Insulation)	-	400	-
Table 1 iii) d) 7)(Thermal stability- Sheath )	-	400	-
Table 1 iii) c) 7)(Thermal stability- Insulation )	-	400	-
Table 1 iii) d) 8)(Cold bend for sheath)	-	400	-
Table 1 iii) c) 8)(Cold bend for insulation)	-	400	-
Table 1 iii) c) 9)(Cold impact for insulation)	-	400	-
Table 1 iii) d) 9)(Cold impact for sheath)	-	400	-
10.4(Flammability test- Unaffected portion)	-	400	-
10.4(Flammability test-Burning after flame removal)	-	400	-
10.5(Oxygen index)	-	400	-
10.8(Smoke density rating)	-	400	-
10.1(HV (water immersion))	-	400	-
10.2(HV (room temperature))	-	400	-
table 1 e) 3) (IR constant- max. Temp)	-	400	-
table 1 e) 3) (IR constant- Room temp )	-	400	-
10.9(Additional ageing test (OU cables only) -HV test (at 60±3oC))	-	400	-
Table 1 iii) c) 3)(TS variation)	-	400	-
Table 1 iii) c) 3)(Elongation variation)	-	400	-
table 1 e) 3) (Volume Resistivity - Maximum temp)	-	400	-
table 1 e) 3) (Volume Resistivity - Room temp )	-	400	-
Table 1 iii) c) 5)(Heat shock-Insulation )	-	400	-
Table 1 iii) d) 5)(Heat shock-Sheath )	-	400	-
4.1(Wrapping test (for Al))	-	400	-
10.11(Per sulphate test (for tinned Cu cable only))	-	400	-
4.2(Conductor resistance test)	-	400	-
4.1(Tensile test (for Al)- After Stranding)	-	400	-
4.1(Tensile test (for Al)-Before Stranding)	-	400	-
9(Overall dimensions)	-	400	-
5.3(Thickness of Insulation)	-	400	-
8.3(Thickness of Sheath)	-	400	-
13(Cable code)	-	0	-
11.2(Legibility)	-	0	-
11.1(Durability)	-	0	-
11(Identification)	-	0	-
12(CONSTRUCTION Core Identification)	-	0	-
8.1(Sheath Material )	-	0	-
7(Binder Tape)	-	0	-
6.2(Filler)	-	0	-
6.1(Filler)	-	0	-
5.1(Insulation)	-	0	-
4.4(Joints in Conductor)	-	0	-
12.0(Core identification)	-	0	-
4, IS 8130(Construction of conductor)	-	0	-
Table 2, IS 8130(No fo wire in a conductor)	-	0	-
8.3(Minimum thickness of Sheath)	-	0	-
8.3(Avarage thickness of Sheath)	-	0	-
5.3(Avarage thickness of insulation)	-	0	-
Table 4(Copper purity test)	-	3000	-

11 Apr, 2028

-
-

Bureau of Indian Standards

The National Standards Body of India

POWERONIC TEST & RESEARCH CENTRE PRIVATE LIMITED, GREATER NOIDA

First Floor, B-2/4, Site-B, UPSIDC Surajpur Industrial Area, Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201306

9602085835 info@poweroniclab.com

Scope List