BIS - LIMS (Laboratory Information Management System)

Central Institute of Petrochemicals Engineering & Technology (CIPET), Murthal

CIPET-Murthal, Near DCRUST, Murthal, Sonipat, Sonipat, Sonipat, Haryana, 131039

22254780 murthal@cipet.gov.in

Scope List

Reset

61 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

19480 View breakup
Rs.19480/- (25% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Raw Material)	-	1050	Nil
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	Nil
4.2(Tapes – Linear Density )	-	500	Nil
4.3(Sacks)	-	300	Nil
4.3.1(Bottom Seam)	-	0	Charge included in sacks , cl.4.3
4.3.2(Mouth)	-	0	Charge included in sacks , cl.4.3
4.4 and Table 1 i(Capacity)	-	250	Nil
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	Nil
5.2 and Table 1 iii(Ends per dm )	-	250	Nil
5.2 and Table 1 iv(Picks per dm )	-	250	Nil
5.1 and Table 1 v(Mass of sack )	-	250	Nil
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	Nil
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	Nil
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	Rs. 10180 for UV Resistance exposure ( 192 hours).
5.2 and Table 1 x(Ash content )	-	950	Nil

Complete

09 Aug, 2025

-
-

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

1500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.2, Fig 1(Dimensions)	-	500		-
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	500		Rs. 1500 subject to minimum test charges

Complete

09 Aug, 2025

-
Up to DN 500mm

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

5950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	3000	Nil
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Mercury (all three extracts))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-10)(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction))	-	0	Test Charges included in Effect on water: Lead (First Extraction)
10.7 of IS 4985(Sulphated Ash content, Annex-B of IS 4985)	-	950	Nil
3.2.1, Table-1, Fig-1(Nominal size)	-	500	Nil
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	500	Nil
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	500	Nil
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	500	Nil

Complete

09 Aug, 2025

-
Up to DN 500mm

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

6475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	1050	Nil
4(Size of fitting)	-	500	Nil
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500	Nil
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0	Test Charges included in Dimension of Socket length
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0	Test Charges included in Dimension of Socket length
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	575	Nil
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	850	Nil
3.2.3(socket, measurements)	-	0	Test Charges included in Dimension of Socket length
6.3(Effect on water test)	-	3000	Nil

Complete

09 Aug, 2025

-
Up to DN 500mm

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

21290 View breakup
Rs.21,290/- (25% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	2000	Nil
3.2(Tapes – Width )	-	250	Nil
3.2(Tapes – Linear Density )	-	500	Nil
3.3(Tying Cord)	-	250	Nil
3.4(Sack)	-	250	Nil
3.4.1(Seam)	-	250	Nil
4.1 and Table 1 i a(Dimensions Outside Length)	-	250	Nil
4.1 and Table 1 i b(Dimensions Outside Width)	-	250	Nil
4.1 and Table 1 ii(Ends per dm )	-	250	Nil
4.1 and Table 1 iii(Picks per dm )	-	0	Test Charges included in Ends per dm
4.2 and Table 1 iv(Mass of sack )	-	250	Nil
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	Nil
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	1100	Nil
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	1100	Nil
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	Test Charges included in Breaking strength
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	Test Charges included in Breaking strength
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12540	UV light exposure Rs. 10340 Breaking strength (warp & weft)
4.1 and Table 1 ix(Ash content )	-	950	Nil

Complete

09 Aug, 2025

-
REVISED VERSION OF IS 14252:2015 INCLUDED w.e.f. 27-08-2019.

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

11975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Marking)	-	250	Nil
3(Designation)	-	250	Nil
4(Colour)	-	300	Nil
6(Dimensions of pipes)	-	250	Nil
7(Visual Appearance)	-	300	Nil
8.1(Hydraulic characteristics)	-	6400	Acceptance Test (48 hrs / 80˚ C) Type test ( 165 hrs / 80˚ C)
8.2(Reversion)	-	700	Specimen charges RS 300
8.3(Density)	-	500	Nil
8.4(Melt Flow Rate)	-	1100	Nil
Cl. 8.5, IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	Nil
Cl. 8.5, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	700	Nil

Complete

09 Aug, 2025

-
Upt o DN 500mm

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

22450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.3(CLASSIFICATION OF PIPES)	-	250	Nil
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1100	Nil
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	500	Nil
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	0	Charges included in melt flow rating (MFR)
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	Nil
5.1 table -1(DIMENSIONS OF PIPES)	-	500	Nil
5.1.2(Ovality)	-	250	Nil
6.1(VISUAL APPEARANCE)	-	300	Nil
7.1 Table -2(Hydraulic Characteristics)	-	6400	Acceptance Test (80˚C/48 hrs ) Quality Test (80˚C/165 hrs )
7.2(Reversion Test)	-	700	Specimen Preparation Rs 300
7.3(Tensile Test)	-	1100	Specimen Preparation Rs 500
7.4table-2(Fusion Compatibility Test)	-	6400	Acceptance Test (80˚C/48 hrs ) Quality Test (80˚C/165 hrs )
7.5(Density)	-	500	Nil
7.6(Melt now Rate (MFR))	-	1100	Nil
(Cl.4.2)(Carbon black- b) Dispersion of carbon black)	-	700	Nil
(Cl.4.2)(Carbon black- a)carbon content)	-	925	Nil
Cl.7.4(Fusion Compatibility Test- b) Acceptance test)	-	0	Test Charges include in Fusion Compatibility
Cl.7.4(Fusion Compatibility Test- a) Quality test)	-	0	Test Charges include in Fusion Compatibility
Cl.6(Visual Appearance)	-	0	Test Charges include in Visual Appearance Test
Cl.5(Dimensions of pipe - ii) Wall thickness maximum)	-	0	Test Charges include in Dimensions Test
Cl.5(Dimensions of pipe - ii) Wall thickness minimum)	-	0	Test Charges include in Dimensions Test
Cl.5(Dimensions of pipe - i) Outside diameter)	-	0	Test Charges include in Dimensions Test
Cl.7.6(Melt Flow Rate)	-	0	Test Charges include in Melt Flow Rate Test
Cl.7.6(Melt Flow Rate)	-	0	Test Charges include in Melt Flow Rate Test

Complete

09 Aug, 2025

-
-

IS 14611 (2016)

Multilayered cross laminated sheets/tarpaulins/covers/agricultural films - Specification (First Revision)

33930 View breakup
Rs.33,930/- (25% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.2,6.3,6.8, table no. 1 Sl No. (vi)(Average tensile strenght and elongation at break after exposing to UV radiation and weathering, Annex- G, Grade- XHN Extra Heavy)	-	12380	UV Light Exposure RS 10180 Tensile & Elongation LD Rs. 1100 Tensile & Elongation TD Rs. 1100
Table1 - v)(Dart Impact Strength)	-	850	Nil
Cl. 6.1(Workmanship)	-	300	Nil
Cl. 6.2(Substance)	-	300	Nil
Cl. 6.3(Accelerated ageing test)	-	4800	Nil
Cl. 6.4(water proofness test)	-	1100	Nil
Cl. 6.5(Strenght of joints/seams)	-	1100	Nil
Cl. 6.6(Flex test)	-	4500	Nil
Cl. 6.7(Ease of in-situ Repair)	-	300	Nil
Cl. 7.1(Eyelets and rope lashing)	-	300	Nil
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	1100	Nil
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra heavy)	-	1100	Nil
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-HN Heavy)	-	1100	Nil
Cl. 6.2,6.3,6.8, table no. 1 Sl No. ii (b)(Tensile strenght, After ageing at 70±1°C 168h. Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speeed 500mm/min, Grade-XHN Extra heavy)	-	1100	Nil
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- LN light)	-	0	Included in tensile test
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- MN Medium)	-	0	Included in tensile test
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- HN Heavy)	-	0	Included in tensile test
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iii (b)(Elongation at break, Ref. IS 13360(Part 5/Sec 1) and IS 13360 (Part 5/Sec 3), test condition-specimen type 2 and test speed 500 mm/min, Grade- XHN Extra Heavy)	-	0	Included in tensile test
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, Annex-F, Grade- HN Heavy)	-	1100	Nil
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- HN heavy)	-	1100	Nil
Cl. 6.2,6.3,6.8, table no. 1 Sl No. iv (b)(Tear strenght, After ageing at 70±1°C for 168h, Annex-F, Grade- XHN Extra heavy)	-	1100	Nil
Cl 4(Types)	-	300	Nil

Complete

09 Aug, 2025

-
REVISED VERSION OF IS 14611:2016 INCLUDED w.e.f. 27-08-2019.

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

A & B

20800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	300	Nil
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100	Nil
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	Nil
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Test Charges included in Dimension Test
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	Test Charges included in Dimension Test
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0	Test Charges included in Dimension Test
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	Test Charges included in Dimension Test
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	Test Charges included in Dimension Test
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	300	Nil
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	700	Specimen Charges RS 300
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	Nil
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	Nil
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	3500	Nil
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2000	55°C/14days Specimen Charge Rs 500
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1100	Specimen Charges RS 300
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	2200	Tensile strength (Before Exposure) RS 1100 Tensile Strength (After Exposure) RS 1100 Specimen Charges RS 500
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	700	Nil
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	Nil
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane)	-	1000	Nil
8.6(Effect on Water Test)	-	3000	Nil

Complete

09 Aug, 2025

-
REVISED VERSION OF IS 13592:2013 INCLUDED w.e.f. 27-08-2019.

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

12056.25 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	Nil
9.5(Tensile Strength IS 12235(Part 13))	-	1100	Specimen Charges Rs. 500
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1100	Specimen Charges Rs. 300
9.3(Density IS 12235 (Part 14))	-	500	Nil
9.2(Internal Diameter)	-	250	Nil
9.1( Visual Appearance)	-	300	Nil
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	250	Nil
8.4(Sealing rings - Hardness)	-	375	Nil
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	250	Nil
7.3.2(Rib height)	-	250	Nil
7.3.1(No.of Ribs)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	250	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	250	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	250	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	250	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	Nil
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	250	Nil
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	250	Nil
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	950	Nil
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	3000	Nil
5.0(Colour of Pipes)	-	250	Nil
9.7(Effect on Water a) Lead (first extraction) b) Lead (Third extraction) c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction) d) Cadmium (All three extracts) e) Mercury (All three extracts) f) Other Toxic Substances )	-	3000	Nil
4.1.2(K-Value as per IS-4669)	-	1100	Nil

Complete

09 Aug, 2025

-
-

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

11725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.c.i (Density)	-	500	Nil
4.1.c.ii (Toluene extract - Annex A)	-	1100	Nil
4.1.c.iii (Volatile matter - Annex B )	-	700	Nil
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	Nil
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	Nil
7.3(Tensile Test)	-	1100	500
7.3(Elongation at Break)	-	0	Test Charges included in Tensile Test
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	77 °C /48 hrs.
5 and Table 1(DIMENSIONS OF PIPES - outside diameters)	-	250	Nil
5 and Table 1(DIMENSIONS OF PIPES - wall thickness shall)	-	0	Test Charges included in DIMENSIONS OF PIPES Test
7.2(Reversion Test)	-	700	Specimen charges Rs. 300
7.1(Hydraulic Characteristics)	-	4000	Acceptance test 20°C/1 hour Rs. 1000 Quality test 70°C/100 hours Rs. 3000
6.1(Visual Appearance)	-	300	Nil
3.1(Class of Pipe)	-	0	Test Charges included in Visual Appearance Test
Cl. 9.0 - 9.1(Minimum Internal Diameter of Coil)	-	250	Nil

Complete

09 Aug, 2025

-
-

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

24380 View breakup
Rs.24,380/- (25% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	250	Nil
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	250	Nil
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	0	Test Charges Included in Ends Test
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	500	Nil
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	Test Charges Included in Dimension Test
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	Test Charges Included in Dimension Test
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	Test Charges Included in Dimension Test
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	0	Test Charges Included in Dimension Test
4.1(Raw Material )	-	2000	Nil
4.2 (Linear Density, 900 denier)	-	500	Nil
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	250	Nil
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	500	Nil
4.3(Sacks)	-	300	Nil
4.4(Seam )	-	250	Nil
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	0	Test Charges Included in Seam Test
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	Test Charges Included in Seam Test
4.4(Seam The stitching shall be done with double fold over seam to)	-	0	Test Charges Included in Seam Test
4.4(to a depth of minimum 25 mm, so that so that)	-	0	Test Charges Included in Seam Test
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	Test Charges Included in Seam Test
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	Test Charges Included in Seam Test
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	400	Nil
4.7(Valve for Filling of Sacks)	-	250	Nil
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) gusseted type 71 + 6%)	-	0	Nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1100	Nil
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1100	Nil
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Nil
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1100	Nil
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	Charges included in Breaking Strength
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	Charges included in Breaking Strength
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100	Nil
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	950	Nil
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	950	Nil
5/5.6 (UV Resistance, )	-	10180	Nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	1100	Nil
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	1100	Nil
4.5(Lamination )	-	250	Nil

Complete

09 Aug, 2025

-
REVISED VERSION INCLUDED OF IS 11652:2017 w.e.f. 27-08-2019.

IS 10889 (2004)

High density polyethylene films (First Revision)

11850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Grades)	-	300	Nil
5.1(Materials)	-	2000	Nil
5.2(Black Compound)	-	1625	CBC 925 CBD 700
6.1.1(Appearance)	-	300	Nil
6.1.2(Film Form)	-	0	Test Charges Included in Appearance
6.1.3(Odour )	-	0	Test Charges Included in Appearance
6.1.4(Density)	-	500	Nil
6.1.5(Melt Flow Rate)	-	1100	Nil
6.1.6(Black Film)	-	1625	CBC 925 CBD 700
6.2.1, Table 1(Nominal Thickness)	-	250	Nil
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	0	Test Charges Included in Nominal Thickness
6.2.2, Table 2(Nominal Width)	-	250	Nil
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	0	Test Charges Included in Nominal Thickness
6.3, Table 3(Yield Tolerance)	-	600	Nil
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	0	Test Charges Included in Yield Tolerance
6.4.1(Tensile Strength at Break)	-	2200	MD 1100 TD 1100
6.4.1, Table 4(Direction)	-	0	Test Charges Included in Tensile Strength at Break
6.4.2(Elongation at Break)	-	0	Test Charges Included in Tensile Strength at Break
6.4.2, Table 5(Direction)	-	0	Test Charges Included in Tensile Strength at Break
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	0	Test Charges Included in Tensile Strength at Break
6.4.3(Impact Resistance (Falling Dart))	-	850	Nil
6.4.3, Table 6(Average Thickness of Film)	-	250	Nil

Complete

09 Aug, 2025

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

Low Density Polythylene Films

20775 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1100	Nil
5.1.1(Appearance)	-	300	Nil
5.1.2(Film Form)	-	0	Test Charges included in Appearance Test
5.1.3(Odour)	-	0	Test Charges included in Appearance Test
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	500	Nil
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	Nil
5.1.6a(Carbon Black Content, Annex-A)	-	925	Nil
5.1.6b(Ash Content, Annex-A)	-	950	Nil
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	Nil
5.2.2(Tolerance on Thickness, Annex-A)	-	250	Nil
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1100	Nil
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4300	Nil
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	Test Charges included in Tensile Strength Test
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	Test Charges included in Tensile Strength Test
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1000	Nil
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
8.1, Table 3(Tear resistance , Annex B)	-	1500	750 x 2 = 1500 (MD, TD)
8.1, Table 3(Puncture resistance , Annex C)	-	750	Nil
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	Test Charges included in Tensile Strength Test
9.1, Table 4(Tear resistance , Annex B)	-	1500	750 x 2 = 1500 (MD, TD)
9.1, Table 4(Puncture resistance , Annex C)	-	0	Test Charges included in Puncture resistance Test
Clause 9.1 (Table 4)(Break Elongation)	-	0	Test Charges included in Tensile Strength Test
Clause 9.1 (Table 4)(Yield Elonation)	-	0	Test Charges included in Tensile Strength Test
Clause 9.1 (Table 4)(Break strength)	-	0	Test Charges included in Tensile Strength Test
Clause 9.1 (Table 4)(Yield strength)	-	0	Test Charges included in Tensile Strength Test
Clause 8.1(Table 3)(Break Elongation)	-	0	Test Charges included in Tensile Strength Test
Clause 8.1(Table 3)(Break strength)	-	0	Test Charges included in Tensile Strength Test
Clause 7.1(Table 2)(Dart Impact Strength)	-	1000	Nil
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1100	Nil
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1100	Nil
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0	Test Charges included in Tensile Strength Test
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0	Test Charges included in Tensile Strength Test
Clause 5.2.3(Tolerance on Width)	-	250	Nil
Cl.5.1.6(a)(Carbon Black Content)	-	0	Test Charges included in CBC Test
Cl.5.1.6(b)(Ash content)	-	0	Test Charges included in ASh Content Test
Cl.5.1.6(c)(Dispersion of Carbon Black)	-	0	Test Charges included in CBD Test

Complete

09 Aug, 2025

-
REVISED VERSION INCLUDED OF IS 2508:2016 w.e.f. 27-08-2019.

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

54525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	5500	500 Specimen charges
8.9 table-6(Elongation at Break)	-	1100	500 Specimen charges
8.8(Tensile Strength for Butt-fusion)	-	1100	500 Specimen charges
8.7(Density)	-	500	nil
8.5 (Oxidation Induction Time)	-	2200	nil
8.4( Melt Flow Rate)	-	1100	nil
8.2(Longitudinal Reversion Test)	-	700	200 Specimen charges
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	nil
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	nil
7.4.1.2(Ovality)	-	250	nil
7.4 table -3 & 4(6.1 Dimensions)	-	250	nil
7.2(Length)	-	250	nil
6.2.1(6.1.1 Identification Stripes)	-	250	nil
6.2(Colour)	-	250	nil
6.1.4(PIPE DESCRIPTION)	-	250	nil
6.1.3 (PIPE DESCRIPTION)	-	250	nil
6, 6.1.2(PIPE DESCRIPTION)	-	250	nil
6, 6.1.1(PIPE DESCRIPTION)	-	250	nil
6, 6.1(PIPE DESCRIPTION)	-	250	nil
8.6(Overall migration)	-	1700	300 Specimen Charges
8.3(Carbon black)	-	925	nil
5.3(e)(Carbon Black Master Batch)	-	925	nil
5.3(d)(Carbon Black Master Batch)	-	925	nil
5.3(c)(Carbon Black Master Batch)	-	925	nil
5.3(b)(Carbon Black Master Batch)	-	925	nil
5.3 (a)(Carbon Black Master Batch)	-	925	nil
5.2(Polyethylene Resin)	-	2000	nil
5, 5.1 table-1(MATERIALS)	-	2000	nil
5.2(Density)	-	500	nil
5.2(MFI @ 1900C/5.0 Kg)	-	1100	nil
5.2(Volatile matter Content)	-	925	nil
5.3(Toluene Extract)	-	1100	nil

Complete

09 Aug, 2025

-
REVISED VERSION INCLUDED OF IS 4984:2016 w.e.f. 27-08-2019. Upto DN 500mm

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

13025 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925	Nil
4.2.3(Carbon Dispersion Test)	-	700	Nil
5(Types and Features )	-	250	Nil
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	250	Nil
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	250	Nil
5.3(Types and Features )	-	0	Test charges included in Types and Features
5.6(Types and Features )	-	0	Test charges included in Types and Features
6.1(Finish)	-	300	Nil
7.1.1(Resistance to Deformation)	-	700	Nil
7.1.2(Resistance to Deformation)	-	1100	Nil
7.2(Resistance to Impact)	-	1100	Nil
7.3(Test for Top Load Resistance)	-	700	Nil
7.4(Tensile Strength)	-	1100	Specimen Charges 500
7.5(Flexural Modulus)	-	1100	Specimen Charges 500
7.6(overall Migration)	-	1700	Specimen Charges 500
9.2.1(Man-Hole and Hand-Hole Lids)	-	500	Lid Lock up & Lid Clearance Dimension
9.2(Man-Hole and Hand-Hole Lids)	-	0	Test Charges included in Man-Hole and Hand-Hole Lids
9.1(Man-Hole and Hand-Hole Lids)	-	0	Test charges included in above CBC & CBD Test.
9.1(Lid Thickness)	-	250	Nil
5.4(Wall Thickness above effective height)	-	250	Nil
5.2 Table 2 (7)(Minimum Wall Thickness)	-	250	Nil
5.1 Table 1 (7)(Minimum Weight of Tank (Without Lid))	-	500	Nil
4.2.1(Density)	-	500	Nil
4.2.2(MFI)	-	1100	Nil
7.6(overall Migration)	-	0	Test charges included in overall Migration test (above)

Complete

09 Aug, 2025

-
Up to 5000 Ltr

IS 9755 (2016)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing fertilizers – Specification (fifth revision)

18230 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.6(Bottom Seam-The number of stitches/dm shall be 14 ± 2.)	-	250	Nil
3.4(Liner-The thickness(A-2 of IS 2508) shall be 40 μm ± 10 percent in case of HMHDPE/ HDPE.)	-	250	Nil
3.4(Liner-The thickness(A-2 of IS 2508) shall be 70 μm ± 10 percent in case of LDPE/LLDPE)	-	250	Nil
3.5(Bottom Seam-The two rows of stitches shall be separated from each other by minimum 5 mm)	-	250	Nil
3.6(Bottom Seam-the outer stitch shall be minimum 8 mm from the outer edge of the sacks.)	-	0	Test Charges Included in Bottom Seam
3.4(Liner-The width of the loose liner shall be minimum 20 mm more than the width of the sack.)	-	0	Test Charges Included in Bottom Seam
3.4.2(Liner-The bottom seal of the loose liner shall be at least 25 mm from the bottom edge.)	-	0	Test Charges Included in Bottom Seam
3.6(Bottom Seam-tThe stitching shall be done with double fold over seam to a depth of minimum 25 mm, so that the stitches pass through a minimum of six layers of the fabric.)	-	0	Test Charges Included in Bottom Seam
3.1(MANUFACTURE-Raw Material- IS 10146 or IS 10910)	-	2000	Nil
3.2(MANUFACTURE-)	-	250	Nil
3.3(Sacks)	-	250	Nil
3.4.1(Liner)	-	0	Test Charges Included in Sacks
3.4.2(Lamination)	-	250	Nil
3.5(Bottom Seam-(see IS 10789).)	-	1100	Nil
3.6.1(Bottom Seam-)	-	250	Nil
3.7(Mouth of the Sack)	-	250	Nil
3.8(Capacity- The sack shall have the nominal capacity of 50 kg.)	-	250	Nil
4.2(UV Resistance)	-	10180	Nil
4.2(UV Resistance-The HDPE/PP woven fabric of sack made out of UV stabilized material shall have at least 50 percent of the original breaking strength when tested after the same has been exposed to UV radiation and weathering as per the method given in Annex D.)	-	2200	Nil
4.3(Mass-(Annexure E))	-	250	Nil

Complete

09 Aug, 2025

-
REVISED VERSION INCLUDED OF 9755:2016 w.e.f. 27-08-2019.

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

111500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4( Designation)	-	250	Nil
Cl 7(Dimensions Of Pipes)	-	250	Nil
Cl 9.1(Hydraulic Characteristics)	-	23200	Acceptance Test (1 h. / 20˚ C) Acceptance Test (22 h. / 95˚ C) Type test ( 165 h. / 95˚ C) Type test ( 1000 h. / 95˚ C) Type test ( 165 h. / 95˚ C)
Cl 9.3(Reversion Test )	-	700	Specimen Charges Rs. 300
Cl 9.4 & Annex B(Impact Strength)	-	1100	Specimen Charges Rs. 300
Cl 9.5(Density)	-	500	Nil
Cl 9.6(Melt Flow Rate)	-	1100	Nil
Cl 9.7(Carbon Black Content & Dispersion)	-	1625	Carbon Black content Rs 925 Carbon Black dispersion Rs 700
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	83825	Thermal Stability by Hydrostatic Pressure (8760 h./110 °C)*
Cl 9.9(Opacity)	-	575	Nil

Complete

09 Aug, 2025

-
-

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

22980 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	300	Nil
4.1(Raw Material)	-	2000	Nil
4.2(Tapes – Width IS 6192 and IS 11197)	-	250	Nil
4.2(Tapes – Linear Density )	-	500	Nil
4.2(Construction)	-	250	Nil
4.3(Sacks)	-	300	Nil
4.3.1(Bottom Seam)	-	250	Nil
4.3.1(The two rows of stitches shall be separated from each other)	-	0	Test Charges Included in Bottom Seam Test
4.3.1( The outer stitch)	-	0	Test Charges Included in Bottom Seam Test
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	Test Charges Included in Bottom Seam Test
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	Test Charges Included in Bottom Seam Test
4.3.1(stitches/dm)	-	0	Test Charges Included in Bottom Seam Test
4.3.2(Mouth)	-	0	Test Charges Included in Bottom Seam Test
4.4(Liner IS 10146 or IS 10910.)	-	250	Nil
4.4(Mass of the loose liner )	-	250	Nil
4.4(Width of the loose liner)	-	250	Nil
4.4(Length of the line)	-	250	Nil
4.4(Bottom seam of the loose liner)	-	250	Nil
4.4.1(Liner)	-	250	Nil
4.5 and Table 1 i(Capacity)	-	250	Nil
5.2 and Table 1 ii a(Dimensions Inside Length)	-	250	Nil
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	Test Charges Included in Dimensions Inside Length Test
5.2 and Table 1 iii(Ends per dm )	-	250	Nil
5.2 and Table 1 iv(Picks per dm )	-	0	Test Charges Included in Ends per dm Test
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	250	Nil
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	250	Nil
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100	Nil
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100	Nil
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100	Nil
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0	Test Charges Included in Breaking Strength Test
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	Test Charges Included in Breaking Strength Test
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	U.V Light Exposure Charges RS.10180
5.2 and Table 1 x(Ash content )	-	950	Nil

Complete

09 Aug, 2025

-
-

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

50 Kg

26455 View breakup
Rs.26,455/- (25% discount for BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250	Nil
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	Nil
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	1100	Nil
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	Nil
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	700	Nil
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	700	Nil
3.2(Unlaminated Fabric Mass )	-	300	Nil
3.3.1(Bottom seam (IS 10789))	-	1100	Nil
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	250	Nil
4.2 and Table 1 ii(Dimensions )	-	250	Nil
5.2 and Table 1 iii(Ends per dm )	-	250	Nil
5.2 and Table 1 iv(Picks per dm )	-	0	Ends & Picks including both test Charges is Rs. 250
4.2 and Table 1 v(Mass of sack )	-	300	Nil
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1100	U.V light Exposure Test Charges Rs. 10180
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	Nil
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	Charge for the same is included with Breaking strength of fabric charges
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1100	Nil
4.2 and Table 1 x(Ash content )	-	950	Nil
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250	Nil
3.1(Material Identification)	-	1050	Test Method-Chemical Analysis
3.1(Overall Migration)	-	1700	Overall Migration Distilled water/10 days/40°C Specimen Charges Rs. 625
3.2(Density)	-	500	Nil
3.2(MFI)	-	1100	Nil

Complete

09 Aug, 2025

-
-

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

30925 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.2(Resistance to External Blows at 0°C)	-	1000	Nil
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	Acceptance Test (1 hr/27 0C)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	Acceptance Test (1 hr/27 0C)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000	Type test ( 1000 hrs/60 0C)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	Test charges included 11.1-Table 7 (MECHANICAL PROPERTIES-Hydro)
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	0	Test charges included 11.1-Table 7 (MECHANICAL PROPERTIES-Hydro)
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	Nil
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	Nil
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	700	200 Specimen Charges
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	Nil
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	300	Nil
9.1(PIPE ENDS)	-	300	Nil
8(SEALING RINGS)	-	300	Nil
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	250	Nil
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	250	Nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	250	Nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	250	Nil
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	250	Nil
7.2.1(DIMENSIONS-Socket)	-	250	Nil
7.1.2.1(DIMENSIONS-PIPE-Average Thickness)	-	250	Nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	250	Nil
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	250	Nil
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	250	Nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	250	Nil
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	250	Nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. Variation)	-	250	Nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	250	Nil
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	250	Nil
7(DIMENSIONS-PIPE-Nominal Diameter)	-	250	Nil
5(CLASSIFICATION OF PIPES)	-	300	Nil
Clause 10.7(Sulphated Ash Content)	-	950	Nil
7.2.1.1 Table3 (Angle of taper (Note-1))	-	250	Nil
10.1(Surface Finish)	-	300	Nil
10.1(Colour)	-	300	Nil
10.3(Effect on Water)	-	3000	Nil
10.3("Effect on Water a) Lead (first extraction) ")	-	0	Total Test Charges for Effect on Water is Rs. 3000.00
10.3(b) Lead (Third extraction))	-	0	Total Test Charges for Effect on Water is Rs. 3000.00
10.3(c) Dialkyl Tin C4 & higher homologues measured as Tin (Third extraction))	-	0	Total Test Charges for Effect on Water is Rs. 3000.00
10.3(d) Cadmium (All three extracts))	-	0	Total Test Charges for Effect on Water is Rs. 3000.00
10.3(e) Mercury (All three extracts))	-	0	Total Test Charges for Effect on Water is Rs. 3000.00
10.3(f) Other Toxic Substances)	-	0	Total Test Charges for Effect on Water is Rs. 3000.00
6(VCM CONTENT)	-	3000	Nil
6(K- VALUE)	-	1100	Nil

Complete

09 Aug, 2025

-
Upto DN 500mm.

IS 8008 : Part 9 (2003)

Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 9 specific requirements for ends caps (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 8008 : Part 8 (2003)

Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 8 specific requirements for reducing tees (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 8008 : Part 7 (2003)

Injection ivIoulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 7 specific requirements for sandwich flanges (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 8008 : Part 6 (2003)

Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 6 specific requirements for pipe ends (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 8008 : Part 5 (2003)

Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 5 specific requirements for ferrule reducers (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 8008 : Part 4 (2003)

Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 4 specific requirements for reducers (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 8008 : Part 3 (2003)

Injection Moulded/Machined High Density Polyethylene (HDPE) Fittings for Potable Water Supplies - - Part 3 : Specific Requirements for 90Â° TEES

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 8008 : Part 2 (2003)

Injection moulded/machined high density polyethylene (HDPE) fittings for potable water supplies - Specification: Part 2 specific requirements for 90° bend (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

09 Aug, 2025

-
-

Bureau of Indian Standards

The National Standards Body of India

Central Institute of Petrochemicals Engineering & Technology (CIPET), Murthal

CIPET-Murthal, Near DCRUST, Murthal, Sonipat, Sonipat, Sonipat, Haryana, 131039

22254780 murthal@cipet.gov.in

Scope List

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found