BIS - LIMS (Laboratory Information Management System)

Cotecna Inspection India Private Limited, Gurugram

Plot No-306, Udyog Vihar, Phase-2, Gurugram, Haryana, Gurugram, Gurugram, Haryana, 122016

9711453100 amit.yadav@cotecna.co.in

Scope List

Reset

66 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 17790 (2022)

INSULATED FLASK FOR DOMESTIC USE SPECIFICATION

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Manufacture and Workmanship)	-	500	-
5.3(Welding Defects)	-	0	-
7.1(Material)	-	0	-
7.1.2.1 & 7.1.2.2(Thickness)	-	500	-
7.1.3(Coating Thickness)	-	500	-
7.1.2.2(Bisphenol A (BPA))	-	4500	-
7.1.4.3(O-Ring / Washer- Defects)	-	500	-
7.2(Capacity)	-	500	-
7.3(Heat Retention Capability)	-	2000	-
7.4(Cold Retention Capability)	-	1000	-
7.5.1(Drop Impact Test)	-	1000	-
7.5.2(Pendulum Impact Test)	-	1000	-
7.6(Fixing Strength of the Handle)	-	1000	-
7.7(Test for Strength of Shoulder Strap)	-	1000	-
7.8(Test for strength of cord)	-	1000	-
7.9(Leakage Test)	-	500	-
7.10(Joint Leak Test)	-	500	-
7.11(Staining Test)	-	500	-
7.13(Seepage test)	-	500	-
7.14(Test for Lever, device for operating Or regulating flow test)	-	1000	-
7.15(Test for length of the shoulder cap)	-	500	-
7.16(Stability of Flask)	-	500	-
7.17(Pour Test)	-	1000	-
9.1(Marking)	-	500	-
9.2(BIS certification marking)	-	500	-
10(Packaging)	-	500	-
7.1.3(Material – coating cadmium)	-	1000	-
5.0(Manufacture and Workmanship)	-	500	-
5.3(Welding Defects)	-	0	-
7.1(Material)	-	0	-
7.1.2.1 & 7.1.2.2(Thickness)	-	500	-
7.1.3(Coating Thickness)	-	1000	-
7.1.2.2(Bisphenol A (BPA))	-	4500	-
7.1.4.3(O-Ring / Washer- Defects)	-	500	-
7.2(Capacity)	-	500	-
7.3(Heat Retention Capability)	-	2000	-
7.4(Cold Retention Capability)	-	1000	-
7.5.1(Drop Impact Test)	-	1000	-
7.5.2(Pendulum Impact Test)	-	1000	-
7.6(Fixing Strength of the Handle)	-	1000	-
7.7(Test for Strength of Shoulder Strap)	-	1000	-
7.8(Test for strength of cord)	-	1000	-
7.9(Leakage Test)	-	500	-
7.10(Joint Leak Test)	-	500	-
7.11(Staining Test)	-	500	-
7.13(Seepage test)	-	500	-
7.14(Test for Lever, device for operating Or regulating flow test)	-	500	-
7.15(Test for length of the shoulder cap)	-	500	-
7.16(Stability of Flask)	-	500	-
7.17(Pour Test)	-	1000	-
9.1(Marking)	-	500	-
9.2(BIS certification marking)	-	500	-
10(Packaging)	-	500	-
7.1.3(Material – coating cadmium)	-	1000	-
7.1.3(Coating- Adhesion test)	-	1000	-
7.1.3(Coating - Thickness test)	-	500	-
7.1.3(Coating- Salt water corrosion test)	-	2000	-
7.1.4.1(Stopper)	-	2000	-
7.1.4.2(O-ring/washer- Overall migration)	-	1000	-
7.1.4.2(O-ring/washer- BPA)	-	4500	-
7.1.5(Auxillary closure)	-	2000	-
7.12(Check for PUF (Polyurethane Foam) or Any Other Similar Thermal Insulation Material)	-	1000	-
7.18(Endurance Test for O-Ring, Washer and Stopper)	-	1000	-
7.1.4.2(O-ring/washer- Shore hardness)	-	1000	-

28 Oct, 2026

-
Included w.e.f. 07.02.2025

IS 14756 (2022)

Draft Indian Standard STAINLESS STEEL COOKWARE SPECIFICATION Second Revision of IS 14756

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Material)	-	0	-
3.2(Material)	-	0	-
3.3(Material)	-	0	-
3.4(Material)	-	0	-
3.4(Material)	-	0	-
3.5(Material)	-	0	-
4.1 (Annex A)(Shapes and Dimensions)	-	500	-
4.2 (Table 1)(Shapes and Dimensions)	-	500	-
4.2 (Table 1)(Shapes and Dimensions)	-	0	-
4.2(Shapes and Dimensions)	-	0	-
4.3(Shapes and Dimensions)	-	500	-
4.4(Shapes and Dimensions)	-	500	-
5.1(Workmanship and Finish)	-	500	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.2(Workmanship and Finish)	-	250	-
5.3(Workmanship and Finish)	-	500	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.4(Workmanship and Finish)	-	18000	-
5.5(Workmanship and Finish)	-	500	-
5.6(Workmanship and Finish)	-	0	-
6.1(Staining Test)	-	1000	-
6.1(Staining Test)	-	1000	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	1000	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	500	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	5000	-
6.5(Coating Thickness Test (For Copper Deposit))	-	500	-
6.6(3 Ply)	-	5000	-
6.7.1(Nominal Capacity Test)	-	500	-
6.7.2(Nominal Capacity Test- Diameter)	-	500	-
6.8.1(Tests on Tempered Glass Lid)	-	1500	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	500	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	1000	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	500	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	500	-
As per Clause 3(Carbon)	-	100	-
As per Clause 3(Silicon)	-	100	-
As per Clause 3(Manganese)	-	100	-
As per Clause 3(Nickel)	-	100	-
As per Clause 3(Chromium)	-	100	-
As per Clause 3(Sulphur)	-	100	-
As per Clause 3(phosphorus)	-	100	-
As per Clause 3(Nitrogen)	-	100	-
As per Clause 3(Titanium)	-	100	-
As per Clause 3(Aluminium)	-	100	-
As per Clause 3(Copper)	-	100	-
As per Clause 3(Magnesium)	-	100	-
As per Clause 3(Iron)	-	100	-
As per Clause 3(Zinc)	-	100	-
As per Clause 3(Arsenic)	-	100	-
As per Clause 3(Antimony)	-	100	-
As per Clause 3(Bismith)	-	100	-
As per Clause 3(Lead)	-	100	-
As per Clause 3(Tellurium)	-	100	-
3.5(Material)	-	250	-
3.5(Material)	-	250	-
3.5(Material)	-	250	-
4.1 (Annex A)(Shapes and Dimensions)	-	500	-
4.2 (Table 1)(Shapes and Dimensions)	-	500	-
4.2 (Table 1)(Shapes and Dimensions)	-	500	-
4.2(Shapes and Dimensions)	-	0	-
4.3(Shapes and Dimensions)	-	500	-
4.4(Shapes and Dimensions)	-	500	-
5.1(Workmanship and Finish)	-	500	-
5.1(Workmanship and Finish)	-	0	-
5.1(Workmanship and Finish)	-	0	-
5.2(Workmanship and Finish)	-	500	-
5.3(Workmanship and Finish)	-	500	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.3(Workmanship and Finish)	-	0	-
5.4(Workmanship and Finish)	-	18000	-
5.5(Workmanship and Finish)	-	500	-
5.6(Workmanship and Finish)	-	500	-
6.1(Staining Test)	-	500	-
6.1(Staining Test)	-	0	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	500	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	1000	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	1000	-
6.5(Coating Thickness Test (For Copper Deposit))	-	1000	-
6.6(3 Ply)	-	1000	-
6.7.1(Nominal Capacity Test)	-	500	-
6.7.2(Nominal Capacity Test- Diameter)	-	500	-
6.8.1(Tests on Tempered Glass Lid)	-	500	-
6.8.1(Tests on Tempered Glass Lid)	-	500	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	500	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	500	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	500	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	500	-
As per Clause 3(Carbon)	-	500	-
As per Clause 3(Silicon)	-	500	-
As per Clause 3(Manganese)	-	500	-
As per Clause 3(Nickel)	-	500	-
As per Clause 3(Chromium)	-	500	-
As per Clause 3(Sulphur)	-	500	-
As per Clause 3(phosphorus)	-	500	-
As per Clause 3(Nitrogen)	-	500	-
As per Clause 3(Titanium)	-	500	-
As per Clause 3(Aluminium)	-	500	-
As per Clause 3(Copper)	-	500	-
As per Clause 3(Magnesium)	-	500	-
As per Clause 3(Iron)	-	500	-
As per Clause 3(Zinc)	-	500	-
As per Clause 3(Arsenic)	-	500	-
As per Clause 3(Antimony)	-	500	-
As per Clause 3(Bismith)	-	500	-
As per Clause 3(Lead)	-	500	-
As per Clause 3(Tellurium)	-	500	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	500	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	500	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	500	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	500	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	500	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	500	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	500	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	500	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	500	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	500	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	500	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	500	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	1000	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	1000	-
4.1 (Annex A)(Shapes and Dimensions)	-	500	-
4.2 (Table 1)(Shapes and Dimensions)	-	500	-
4.2 (Table 1)(Shapes and Dimensions)	-	500	-
4.2(Shapes and Dimensions)	-	500	-
4.3(Shapes and Dimensions)	-	500	-
4.4(Shapes and Dimensions)	-	500	-
5.1(Workmanship and Finish)	-	250	-
5.1(Workmanship and Finish)	-	250	-
5.1(Workmanship and Finish)	-	250	-
5.2(Workmanship and Finish)	-	250	-
5.3(Workmanship and Finish)	-	250	-
5.3(Workmanship and Finish)	-	250	-
5.3(Workmanship and Finish)	-	250	-
5.3(Workmanship and Finish)	-	250	-
5.3(Workmanship and Finish)	-	250	-
5.3(Workmanship and Finish)	-	250	-
5.4(Workmanship and Finish)	-	18000	-
5.5(Workmanship and Finish)	-	500	-
5.6(Workmanship and Finish)	-	500	-
6.1(Staining Test)	-	1000	-
6.1(Staining Test)	-	1000	-
6.2(Mechanical Shock Test (For Cladded Utensils only))	-	1000	-
6.3(Thermal Shock Test (For Cladded Utensils only))	-	500	-
6.4(Dry Heat Test (For Cladded Utensils only))	-	5000	-
6.5(Coating Thickness Test (For Copper Deposit))	-	500	-
6.6(3 Ply)	-	5000	-
6.7.1(Nominal Capacity Test)	-	500	-
6.7.2(Nominal Capacity Test- Diameter)	-	500	-
6.8.1(Tests on Tempered Glass Lid)	-	1500	-
6.8.1(Tests on Tempered Glass Lid)	-	0	-
6.8.2(Tests on Tempered Glass Lid (Ball drop test))	-	500	-
6.8.3(Tests on Tempered Glass Lid (thermal shock test))	-	1000	-
6.8.4.1(Tests on Tempered Glass Lid (Free Fall Test with rim facing down))	-	500	-
6.8.4.2(Tests on Tempered Glass Lid (Free Fall Test without rim facing down))	-	500	-
As per Clause 3(Carbon)	-	100	-
As per Clause 3(Silicon)	-	100	-
As per Clause 3(Manganese)	-	100	-
As per Clause 3(Nickel)	-	100	-
As per Clause 3(Chromium)	-	100	-
As per Clause 3(Sulphur)	-	100	-
As per Clause 3(phosphorus)	-	100	-
As per Clause 3(Nitrogen)	-	100	-
As per Clause 3(Titanium)	-	100	-
As per Clause 3(Aluminium)	-	100	-
As per Clause 3(Copper)	-	100	-
As per Clause 3(Magnesium)	-	100	-
As per Clause 3(Iron)	-	100	-
As per Clause 3(Zinc)	-	100	-
As per Clause 3(Arsenic)	-	100	-
As per Clause 3(Antimony)	-	100	-
As per Clause 3(Bismith)	-	100	-
As per Clause 3(Lead)	-	100	-
As per Clause 3(Tellurium)	-	100	-
CL-5.4(CL-4.1 of IS 13395)(Construction)	-	250	-
CL-5.4(CL-4.2 of IS 13395)(Materials)	-	0	-
CL-5.4(CL-4.3 of IS 13395)(Selection and Size)	-	100	-
CL-5.4(CL-4.4 of IS 13395)("Position of Handle and Knob with Respect to Cookware")	-	500	-
CL_5.4(CL-4.5 of IS 13395)(Attachment to Cookware)	-	500	-
CL-5.4(CL-5.2 of IS 13395)(Bending Strength)	-	500	-
CL-5.4(CL-5.3 of IS 13395)(Torque Strength)	-	500	-
CL-5.4(CL-5.4 of IS 13395)(Impact Strength)	-	500	-
CL-5.4(CL-5.5 of IS 13395)(Fatigue Resistance)	-	500	-
CL-5.4(CL-5.6 of IS 13395)(Leakage)	-	500	-
CL-5.4(CL-5.7 of IS 13395)(Thermal Insulation)	-	500	-
CL-5.4(CL-5.8 of IS 13395)(Heat Resistance)	-	500	-
CL-5.4(CL-5.9 of IS 13395)(Washing Resistance (Type Test))	-	500	-
CL-5.4(CL-5.10 of IS 13395)(Burning Resistance)	-	500	-

28 Oct, 2026

-
Included w.e.f. 07.02.2025

IS 9730 (2008)

Non - Stick unreinforced plastics coatings on domestic cooking utensils - Specification (First Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Material)	-	500	-
4.2(Visual Defects)	-	500	-
4.3 & 7.2(Thickness)	-	1000	-
4.4 & 7.3(Non-stick Quality)	-	2000	-
4.5 & 7.4(Salt Water Corrosion Resistance)	-	2000	-
4.6, 7.5.2 & 7.5.3(Adhesion Test)	-	2500	-
5(Marking)	-	500	-
6(Instructions for use)	-	500	-
4.1(Material)	-	0	-
4.2(Visual Defects)	-	0	-
4.3 & 7.2(Thickness)	-	0	-
4.4 & 7.3(Non-stick Quality)	-	0	-
4.5 & 7.4(Salt Water Corrosion Resistance)	-	0	-
4.6, 7.5.2 & 7.5.3(Adhesion Test)	-	0	-
5(Marking)	-	0	-
6(Instructions for use)	-	0	-

28 Oct, 2026

-
-

IS 1660 (2024)

Wrought and Cast Aluminium Utensils Specification ( Second Revision )

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Classification Heavy/Medium/L:ight)	-	250	-
0.5(Fabrication)	-	250	-
5.1(The utensil shall be pressed or spun from one piece)	-	250	-
5.2( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-	250	-
5.2(Lid Thickness of the finished utensil, mm)	-	250	-
6.1 & Table 1( i) Name of Utensil )	-	250	-
6.1 & Table 1(ii) Shape of Utensil)	-	250	-
6.1 & Table 1( Nominal Size, mm)	-	250	-
6.1 & Table 1(Inside dia, Φ D mm Not declared )	-	250	-
6.1 & Table 1(Outside dia Ф NA)	-	250	-
6.1 & Table 1(Height NA)	-	250	-
6.1 & Table 1(Capacity, l NA)	-	250	-
6.1( Minimum sheet thickness for nominal size )	-	250	-
7.1(HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-	250	-
7.2(Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-	750	-
8.1(The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-	500	-
8.2(The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-	250	-
8.4.1.2( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-	250	-
8.4.2(A coating of thickness 25 to 100 microns is generally required)	-	750	-
8.4.3(Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-	750	-
8.4.4(The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-	250	-
8.4.4(The film will appear dark grey when wet. )	-	250	-
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-	750	-
9(The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-	500	-
10(Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness at the bottom)	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness of wall at top edge)	-	250	-
Clause 3.1.3, Table 2(Minimum Cover Thickness)	-	250	-
Clause 8.6.1(Performance test)	-	750	-
Clause 8.6.2(Ground Nut Oil Test for Leakage)	-	1000	-
5.4(Qualitative and Anodized Coating)	-	500	-
5.5(Qualitative and Anodized Coating)	-	500	-
8.3(Anodized Coating)	-	250	-
8.5(Plastic Coating)	-	2000	-
8.1(Qualitative)	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness at the bottom)	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness of wall at top edge)	-	250	-
Clause 3.1.3, Table 2(Minimum Cover Thickness)	-	250	-
Clause 8.6.1(Performance test)	-	250	-
Clause 8.6.2(Ground Nut Oil Test for Leakage)	-	1000	-
4(Material)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Nitrogen of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Titanium of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Vanadium of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Boron of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Copper of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Molybdenum of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Nickel of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Chromium of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Aluminium of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Silicon of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Manganese of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Phosphorous of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Sulphor of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Carbon of IS 6911)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Titanium of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Chromium of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Zinc of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Manganese of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Iron of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Silicon of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Magnesium of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Copper of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Aluminium of IS 737)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Titanium / other Grain of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Chromium of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Zinc of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Manganese of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Iron of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Silicon of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Magnesium of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Copper of IS 21)	-	100	-
( Clauses 4, 4.1, 4.2 and 4.3)(Aluminium of IS 21)	-	100	-
3.1(Classification Heavy/Medium/L:ight)	-	250	-
0.5(Fabrication)	-	250	-
5.1(The utensil shall be pressed or spun from one piece)	-	250	-
5.2( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-	250	-
5.2(Lid Thickness of the finished utensil, mm)	-	250	-
6.1 & Table 1( i) Name of Utensil )	-	250	-
6.1 & Table 1(ii) Shape of Utensil)	-	250	-
6.1 & Table 1( Nominal Size, mm)	-	250	-
6.1 & Table 1(Inside dia, Φ D mm Not declared )	-	250	-
6.1 & Table 1(Outside dia Ф NA)	-	250	-
6.1 & Table 1(Height NA)	-	250	-
6.1 & Table 1(Capacity, l NA)	-	250	-
6.1( Minimum sheet thickness for nominal size )	-	250	-
7.1(HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-	250	-
7.2(Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-	750	-
8.1(The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-	500	-
8.2(The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-	250	-
8.4.1.2( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-	250	-
8.4.2(A coating of thickness 25 to 100 microns is generally required)	-	750	-
8.4.3(Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-	750	-
8.4.4(The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-	250	-
8.4.4(The film will appear dark grey when wet. )	-	250	-
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-	750	-
9(The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-	500	-
10(Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness at the bottom)	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness of wall at top edge)	-	250	-
Clause 3.1.3, Table 2(Minimum Cover Thickness)	-	250	-
Clause 8.6.1(Performance test)	-	750	-
Clause 8.6.2(Ground Nut Oil Test for Leakage)	-	1000	-
5.4(Qualitative and Anodized Coating)	-	500	-
5.5(Qualitative and Anodized Coating)	-	500	-
8.3(Anodized Coating)	-	250	-
8.5(Plastic Coating)	-	2000	-
8.1(Qualitative)	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness at the bottom)	-	250	-
Clause 3.1.3, Table 2(Minimum Thickness of wall at top edge)	-	250	-
Clause 3.1.3, Table 2(Minimum Cover Thickness)	-	250	-
Clause 8.6.1(Performance test)	-	250	-
Clause 8.6.2(Ground Nut Oil Test for Leakage)	-	1000	-
4(Material)	-	100	-
Cl-3.1.1, 3.1.2(Minimum Thickness of Sheet)	-	250	-
Cl-3.1.3, Table-2(Minimum Thickness at the Bottom)	-	250	-
Cl-3.1.3, Table-2(Minimium Thickness of Wall at the Top Edge)	-	250	-
Cl-3.1.3, Table-2(Minimum Cover Thickness)	-	250	-
Cl-4.1(Main body of utensil)	-	250	-
Cl-4.1(Cast cookware)	-	250	-
Cl-4.1(Other aluminum components and parts)	-	250	-
Cl-4.1.1(Lids (material))	-	250	-
Cl-4.1.1(Minimum thickness of lid)	-	250	-
Cl-4.1.2(Minimum thickness of glass)	-	250	-
Cl-4.1.2(Material of rim)	-	250	-
Cl-4.1.2(Minimum thickness of rim)	-	250	-
Cl-4.2(Material of strips)	-	250	-
Cl-4.2(Stainless steel handles, rivets and fittings)	-	250	-
Cl-4.3(Clips of lunch box)	-	250	-
Cl-4.3(Clips of lunch box)	-	250	-
Cl-4.3(Rivets used in lunch box)	-	250	-
Cl-4.4(Screws, studs/nuts, and locking loop)	-	250	-
Cl-4.5(Rivets for fixing of handles)	-	250	-
Cl-4.5(Material of cap)	-	250	-
Cl-4.6(Strips used for flame guards)	-	250	-
Cl-4.6(stainless steel)	-	250	-
Cl-5(Fabrication)	-	250	-
Cl-6(Shape and Dimensions)	-	250	-
Cl-7.1(Handles, when fitted)	-	250	-
Cl-7.2(Handles)	-	250	-
Cl-7.3 (Cl- 4.1 of IS 13395)(Construction)	-	250	-
Cl-7.3 (Cl- 4.2 of IS 13395)(Materials)	-	250	-
Cl-7.3 (Cl- 4.3 of IS 13395)(Selection and Size)	-	400	-
Cl-7.3 (Cl- 4.4 of IS 13395)(Position of Handle and Knob with Respect to Cookware)	-	400	-
Cl-7.3 (Cl- 4.5 of IS 13395)(Attachment to Cookware)	-	400	-
Cl-7.3 (Cl- 5.2 of IS 13395)(Bending Strength)	-	400	-
Cl-7.3 (Cl- 5.3 of IS 13395)(Torque Strength)	-	400	-
Cl-7.3 (Cl- 5.4 of IS 13395)(Impact Strength)	-	400	-
Cl-7.3 (Cl- 5.5 of IS 13395)(Fatigue Resistance)	-	3500	-
Cl-7.3 (Cl- 5.6 of IS 13395)(Leakage)	-	400	-
Cl-7.3 (Cl- 5.7 of IS 13395)(Thermal Insulation)	-	1000	-
Wrought and Cast Aluminium Utensils — Specification(Heat Resistance)	-	250	-
Cl-7.3 (Cl- 5.9 of IS 13395)(Washing Resistance (Type Test))	-	1000	-
Cl-7.3 (Cl- 5.10 of IS 13395)(Burning Resistance)	-	250	-
Cl-8(Workmanship and Finish)	-	250	-
Cl-8.3(Utensils, if anodized, fully or partially)	-	250	-
Cl-8.3(Minimum nominal thickness)	-	250	-
Cl-8.3(Thickness of hard anodized)	-	250	-
Cl-8.3(Finish and appearance of hard anodized)	-	250	-
Cl-8.3(Abrasion resistance of hard anodized)	-	750	-
Cl-8.3(Colour of hard anodized)	-	250	-
Wrought and Cast Aluminium Utensils — Specification(Lid of the cookware)	-	250	-
Cl-8.5(Non-stick unreinforced PTFE)	-	2000	-
Cl-8.6(Ceramic coating)	-	2000	-
Cl-8.7(The thickness test, adhesion test)	-	250	-
Cl-8.7(Minimum thickness of coating)	-	250	-
Cl-8.7.1(Dry heat the cookware)	-	750	-
Cl-8.8(Requirements of PTFE)	-	2000	-
Cl-8.9(Material for induction plate)	-	250	-
Cl-8.9(Test for Induction compatible base)	-	250	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	500	-
Cl-8.10.1(Tests for Lunch Boxes- Performance Test)	-	500	-
Cl-8.10.2(Tests for Lunch Boxes- Ground Nut Oil Test for Leakage)	-	500	-
Cl-8.11.1(Test(s) on Tempered Glass Lid- Fragmentation Test)	-	400	-
Cl-8.11.2(Test(s) on Tempered Glass Lid-Ball Drop Test)	-	400	-
Cl-8.11.3(Test(s) on Tempered Glass Lid- Thermal Shock Test)	-	400	-
Cl-8.11.4(Test(s) on Tempered Glass Lid- Free Fall Test)	-	400	-
Cl-9.1(Normal Capacity)	-	250	-
Cl-9.2(Normal Capacity of internal diameter)	-	250	-

28 Oct, 2026

-
Included.w.e.f.26.12.2024 Exclusion Cl 8.3 (Hardness of hard anodized)

IS 17043 : Part 2 (2024)

Shoes: Shoes for General Purpose

65000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.1(Shape and Design)	-	200	-
Cl-5.3(Material)	-	200	-
Cl-5.4, Table-1 (i)(Bond strength, N/mm, Min Upper to outsole, N/mm, Min)	-	1080	-
Cl-5.4, Table-1 (ii)(Inter layer bond strength,= N/mm, Min Midsole to outsole, N/mm, Min)	-	1080	-
Cl-5.4, Table-1 (iii)(Whole shoe flexing, flexes)	-	1200	-
Cl-5.4, Table-1 (iv)(Water proofness on complete shoe)	-	1000	-
Cl-5.4, Table-1 (v)(Slip resistance, Cof(1), Min dry and wet* (quarry tile))	-	1500	-
Cl-5.4, Table-1 (vi)(Attachment strength of strap and buckle/D-ring N)	-	800	-
Cl-5.4, Table-1 (vii)(Attachment strength of strap and velcro , N, Min)	-	800	-
Cl-5.4, Table-1 (viii)(Strength of eyelet attachment, N, Min)	-	800	-
Cl-5.4, Table-1 (ix)(Heel pull off strength, N, Min)	-	800	-
Cl-5.4, Table-1 (x)(Top piece attachment strength, N, Min)	-	800	-
Cl-5.4, Table-1 (xi)(Seam strength, N/mm, Min)	-	500	-
Cl-5.4, Table-1 (xii)(Whole shoe topline strength, N, Min)	-	800	-
Cl-5.4, Table-1 (xiii)(Abrasion resistance (volume loss), mm3)	-	900	-
Cl-5.4, Table-1 (xiv)(Chemical requirements(3))	-	40000	-
Cl-5.4, Table-1 (xv)(Lead content (as Pb) ppm, Max)	-	900	-
Cl-5.4, Table-1 (xvi)(Hydrolysis resistance,(4) cut growth at 150 000 flexes, mm, Max)	-	2000	-
Cl-6.1.1, Table-2 (i)(Tear trength, N)	-	450	-
Cl-6.1.1, Table-2 (ii)(Flexing resistance, flexes)	-	1000	-
Cl-6.1.1, Table-2 (iii)(Colour fastness to rubbing (marring/staining))	-	450	-
Cl-6.1.1, Table-2 (iv)(Colour fastness to water (contact method- multi fabrics))	-	450	-
Cl-6.1.1, Table-2 (v)(Water vapour permeability,mg/cm2 /h, Min Water vapour coefficient,mg/cm2 , Min)	-	630	-
Cl-6.1.1, Table-2 (vi)(Stitch tear strength, N/mm, Min)	-	450	-
Cl-6.1.1, Table-2 (vii)(Abrasion resistance)	-	1500	-
Cl-6.1.2, Table-3 (i)(Colour fastness to light, Marring, Min)	-	1500	-
Cl-6.1.2, Table-3 (ii)(Water resistance)	-	630	-
Cl-6.1.2, Table-3 (iii)(Flexing resistance, flexes at (-) 5 °C 25 000 flexes)	-	2000	-
Cl-6.1.3, Table- 4 (i)(Breaking strength, N/mm, Min Elongation at break, percent, Min)	-	450	-
Cl-6.1.3, Table- 4 (ii)(Tear Strength, N, Min)	-	450	-
Cl-6.1.3, Table- 4 (iii)(Strength at needle perforation, N/mm, Min)	-	450	-
Cl-6.1.3, Table- 4 (iv)(Flexing resistance, Flexes)	-	2000	-
Cl-6.1.3, Table- 4 (v)(Water vapour permeability (WVP), mg/cm2 /h, Min)	-	630	-
Cl-6.1.3, Table- 4 (vi)(Hydrolysis resistance)	-	2000	-
Cl-6.1.3, Table- 4 (vii)(Abrasion resistance)	-	1500	-
Cl-6.1.4, Table-5 (i)(Colour fastness to light, Marring, Min)	-	1500	-
Cl-6.1.4, Table- 5 (ii)(Flexing resistance, flexes at (-) 5 ºC, s 25 000 flexes)	-	2000	-
Cl-6.2, Table-6 (i)(Tear strength, N, Min)	-	450	-
Cl-6.2, Table-6 (ii)(Abrasion resistance)	-	1500	-
Cl-6.2, Table-6 (iii)(Colour fastness rubbing (crocking))	-	450	-
Cl-6.2, Table-6 (iv)(Colour fastness to perspiration)	-	700	-
Cl-6.2, Table-6 (v)(Water vapour permeability, mg/cm2 /h, Min Water vapour coefficient, mg/cm2, Min)	-	630	-
Cl-6.3, Table-7 (i)(Flexing index, Min)	-	800	-
Cl-6.3, Table-7 (ii)(Abrasion resistance at 400 cycles)	-	800	-
Cl-6.3, Table-7 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	700	-
Cl-6.4, Table-8 (i)(Thickness, mm, Min)	-	200	-
Cl-6.4, Table-8 (ii)(Abrasion resistance)	-	1500	-
Cl-6.4, Table-8 (iii)(Water absorption, mg/cm2 , Min Water desorption, percent, Min)	-	700	-
Cl-6.5.1, , Table-9 (i)(Flexing resistance)	-	800	-
Cl-6.5.1, , Table-9 (ii)(Hydrolysis resistance, cut growth at 150 000 flexes, mm, Max)	-	2000	-
Cl-6.5.1, , Table-9 (iii)(Compression set, percent, Max)	-	1000	-
Cl-6.5.2.1, Table-10 (i)(Grain crack index, Min)	-	700	-
Cl-6.5.2.1, Table-10 (ii)(Density, g/cm3 , Min)	-	300	-
Cl-6.5.2.2, Table-11 (i)(Water resistance, (dynamic method))	-	700	-
Cl-6.5.2.3, Table-12 (i)(Hardness, Min)	-	300	-
Cl-6.5.2.3, Table-12 (ii)(Density, g/cm3 , Max)	-	300	-
Cl-6.5.2.3, Table-12 (iii)(Abrasion resistance (volume loss), mm3 , Max)	-	1080	-
Cl-6.5.2.3, Table-12 (iv)(Bond Strength between Rubber top-lift and adjacent material, N/mm, Min)	-	1000	-
Cl-6.6, Table-13 (i)(Heat shrinkage, percent, Max)	-	800	-
Cl-6.6, Table-13 (ii)(Split tear strength, kg/25 mm, Min)	-	600	-
Cl-6.6, Table-13 (iii)(Compression set, percent, Max)	-	800	-
Cl-6.7, Table-14 (i)(Hardness, N)	-	300	-
Cl-6.7, Table-14 (ii)(Resilience, percent)	-	950	-
Cl-6.7, Table-14 (iii)(Moisture resistance, percent)	-	950	-
Cl-6.10, Table-17 (i)(Lace breaking strength, N, Min)	-	600	-
Cl-6.10, Table-17 (ii)(Lace tag strength, N, Min)	-	600	-
Cl-6.10, Table-17 (iii)(Lace to lace abrasion resistance, cycles)	-	800	-
Cl-6.10, Table-17 (iv)(Colour fastness to water for lace contact methodstaining Gray scale rate , Min)	-	450	-
Cl-6.10, Table-17 (v)(Corrosion resistance)	-	900	-
Cl-6.11, Table-18 (ii)(Security of puller attachment strength, N, Min)	-	500	-
Cl-6.11, Table-18 (iii)(Lateral load, N, Min)	-	500	-
Cl-6.11, Table-18 (iv)(End attachment strength, N, Min)	-	500	-
Cl-8.1(Marking)	-	200	-
Cl-6.7, Table-14 (iv)(Area shape retention, percent (a) Initial, Min b) After 10 collapsing load, Min)	-	1200	-
Cl-6.7, Table-14 (v)(Adhesion strength, N/mm)	-	1080	-
Cl-6.8, Table-15 (i)(Peel strength, N/mm a) Initial, Min b) After 5 000 wear cycles, Min)	-	1080	-
Cl- 6.8, Table-15 (ii)(a) Shear strength, kPa b) Initial, Min)	-	800	-
Cl- 6.9, Table-16 (i)(Limit of useful extension, percent, Min)	-	800	-
Cl- 6.9, Table-16 (ii)(Needle strength, N/mm, Min)	-	600	-
Cl-6.11, Table-18 (i)(Fatigue resistance, cycles, Min)	-	800	-

28 Oct, 2026

-
Included w.e.f 27.11.2024 Exclusion Cl-6.5.2.1, S.No (1), iii (Abrasion resistance, mm/kcs, Max)

IS 17043 : Part 1 (2024)

Shoes - Specification Part 1 Shoes for Services

65000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Design)	-	200	-
Cl-4.3.1(Size)	-	200	-
Cl-4.3.2(Weight)	-	200	-
Cl-4.4(Height of Upper)	-	200	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	1000	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	1080	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	2500	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	6000	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	1000	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	1000	-
Cl-4.6.1(Material)	-	200	-
Cl-4.6.2(Tear Strength)	-	450	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	630	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	630	-
Cl-4.7.1(Material)	-	200	-
Cl-4.7.2(Tear Strength)	-	450	-
Cl-4.7.3(Abrasion Resistance)	-	1500	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	630	-
Cl. 4.8.1(Material)	-	200	-
Cl-4.8.2(Abrasion Resistance)	-	900	-
Cl-4.8.3(Water Absorption and Desorption)	-	700	-
Cl-4.9.3(Abrasion Resistance)	-	1500	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	200	-
Cl-4.11.1(Material)	-	200	-
Cl-4.11.2(Tear Strength)	-	450	-
Cl-4.12(Closing Thread)	-	450	-
Cl-4.13.2(Thickness)	-	200	-
Cl-4.13.3(Moulded Density)	-	300	-
Cl-4.13.4(Hardness)	-	200	-
Cl-4.13.5(Ageing Test)	-	500	-
Cl-4.13.6(Tear Strength)	-	450	-
Cl-4.13.7(Abrasion Resistance)	-	1080	-
Cl-4.13.8(Flexing Resistance)	-	1080	-
Cl-4.14(Eyelet)	-	1000	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	500	-
Cl-5(Chemical Requirements)	-	40000	-
Cl-7(Marking)	-	200	-
Cl.4.5.8(Energy Absorption of Seat Region)	-	600	-
Cl- 4.5.3.1(Upper-outsole bond strength)	-	1080	-
Cl.4.5.3.2(Interlayer bond strength)	-	1080	-
Cl-4.9.1(Material)	-	200	-
Cl-4.9.2(Water Absorption and Desorption)	-	900	-
Cl-4.13.1(Material)	-	200	-
Cl-4.2(Design)	-	200	-
Cl-4.3.1(Size)	-	200	-
Cl-4.3.2(Weight)	-	200	-
Cl-4.4(Height of Upper)	-	200	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	1000	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	1080	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	2500	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	6000	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	1000	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	1000	-
Cl-4.6.1(Material)	-	200	-
Cl-4.6.2(Tear Strength)	-	450	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	630	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	630	-
Cl-4.7.1(Material)	-	200	-
Cl-4.7.2(Tear Strength)	-	450	-
Cl-4.7.3(Abrasion Resistance)	-	1500	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	630	-
Cl. 4.8.1(Material)	-	200	-
Cl-4.8.2(Abrasion Resistance)	-	900	-
Cl-4.8.3(Water Absorption and Desorption)	-	700	-
Cl-4.9.3(Abrasion Resistance)	-	1500	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	200	-
Cl-4.11.1(Material)	-	200	-
Cl-4.11.2(Tear Strength)	-	450	-
Cl-4.12(Closing Thread)	-	450	-
Cl-4.13.2(Thickness)	-	200	-
Cl-4.13.3(Moulded Density)	-	300	-
Cl-4.13.4(Hardness)	-	200	-
Cl-4.13.5(Ageing Test)	-	500	-
Cl-4.13.6(Tear Strength)	-	450	-
Cl-4.13.7(Abrasion Resistance)	-	1080	-
Cl-4.13.8(Flexing Resistance)	-	1080	-
Cl-4.14(Eyelet)	-	1000	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	500	-
Cl-5(Chemical Requirements)	-	40000	-
Cl-7(Marking)	-	200	-
Cl.4.5.8(Energy Absorption of Seat Region)	-	600	-
Cl- 4.5.3.1(Upper-outsole bond strength)	-	1080	-
Cl.4.5.3.2(Interlayer bond strength)	-	1080	-
Cl-4.9.1(Material)	-	200	-
Cl-4.9.2(Water Absorption and Desorption)	-	900	-
Cl-4.13.1(Material)	-	200	-
Cl-4.15.1(Material)	-	200	-
4.9 Insocks(Insock thickness)	-	200	-
Cl-5, Table 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	4460	-
Cl-5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2610	-
Cl-5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2610	-
Cl-5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	1490	-
Cl-5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	4950	-
Cl-5, Table no 1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	4300	-
Cl-5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	4300	-
Cl-5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	6930	-
Cl-5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	3470	-
Cl-5, Table no 1 of IS 17011 (x)(pH)	-	300	-
Cl-5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	3960	-
Cl-5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	3470	-

28 Oct, 2026

-
Included w.e.f 30.01.2025

Bureau of Indian Standards

The National Standards Body of India

Cotecna Inspection India Private Limited, Gurugram

Plot No-306, Udyog Vihar, Phase-2, Gurugram, Haryana, Gurugram, Gurugram, Haryana, 122016

9711453100 amit.yadav@cotecna.co.in

Scope List