BIS - LIMS (Laboratory Information Management System)

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

plot no.160,Industrial Area Phase-9, Sahibzada Ajit Singh Nagar, S.A.S Nagar, Punjab, 160062

9888717272 chandigarh@alphatesthouse.com

Scope List

Reset

292 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

241

IS 1254 (2007)

Corrugated aluminium sheet (Fourth Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(FREEDOM FROM DEFECTS)	-	500	-
4(SUPPLY OF MATERIAL)	-	500	-
5(PROFILE)	-	500	-
6(MATERIAL)	-	7000	-
7.2(WIDTH)	-	1000	-
7.3(LENGTH)	-	1000	-
7.4(SQUARENESS)	-	1000	-
7.5(Depth and Pitch of the Corrugation)	-	2500	-
8(FINISH)	-	500	-
9(MARKING)	-	500	-
3(FREEDOM FROM DEFECTS)	-	-	-
4(SUPPLY OF MATERIAL)	-	-	-
5(PROFILE)	-	-	-
6(MATERIAL)	-	-	-
7.2(WIDTH)	-	-	-
7.3(LENGTH)	-	-	-
7.4(SQUARENESS)	-	-	-
7.5(Depth and Pitch of the Corrugation)	-	-	-
8(FINISH)	-	-	-
9(MARKING)	-	-	-

31 Dec, 2029

-
-

242

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

0 -100 mm

8100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Freedom from Defects)	-	500	-
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	500	-
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	1000	-
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	500	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	300	-
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	600	-
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	1000	-
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	600	-
7(Dimension - IS 3965)	-	500	-
11(Marking)	-	200	-
Table-1, Clause - 5.1(Copper)	-	300	-
Table-1, Clause - 5.1(Iron)	-	300	-
Table-1, Clause - 5.1(Magnesium)	-	300	-
Table-1, Clause - 5.1(Manganese)	-	300	-
Table-1, Clause - 5.1(Titanium)	-	300	-
Table-1, Clause - 5.1(Silicon)	-	300	-
Table-1, Clause - 5.1(Chromium)	-	300	-
Table-1, Clause - 5.1(Zinc)	-	300	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

243

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

ALUMINIUM PLATE

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	1000	-
5(chemical composition)	-	12000	-
6.1 table 2(0.2% proof strength)	-	1500	-
6.1 table 2(tensile strength)	-	2000	-
6.1 table 2(Elongation)	-	1500	-
8(Dimensions & Tolerances)	-	2000	-
4(Freedom from defect)	-	1000	-
5(chemical composition)	-	12000	-
6.1 table 2(0.2% proof strength)	-	1500	-
6.1 table 2(tensile strength)	-	2000	-
6.1 table 2(Elongation)	-	1500	-
8(Dimensions & Tolerances)	-	2000	-
5.1, Table 1(Aluminium)	-	1200	-
5.1, Table 1(Copper)	-	1200	-
5.1, Table 1(Magnesium)	-	1200	-
5.1, Table 1(Silicon)	-	1200	-
5.1, Table 1(Iron)	-	1200	-
5.1, Table 1(Mangnese)	-	1200	-
5.1, Table 1(Zinc)	-	1200	-
5.1, Table 1(Titanium and /or other grain refining element)	-	1200	-
5.1, Table 1(Chromium)	-	1200	-
5.1, Table 1(Vanadium)	-	1200	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

244

IS 1285 (2023)

WROUGHT ALUMINIUM AND ALUMINIUM ALLOYS EXTRUDED ROUND TUBE AND HOLLOW SECTIONS FOR GENERAL ENGINEERINGPURPOSES SPECIFICATION

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	200	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	200	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	4400	-
10(Tensile test)	-	2200	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	600	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	600	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
6.1("The extruded round tube and hollow sections shall be sound and visually free from harmful defects. ")	-	200	-
6.2(Slight discoloration due to heat treatment, minor polishing marks and spiral marks due to roll straightening shall not be a cause for rejection.)	-	200	-
8("Dimensions and tolerances of the material shall be as laid down in the Indian Standards indicated below: a) Extruded round tube IS 2673; and b) Extruded hollow sections IS 6477.")	-	1000	-
9(" Extruded round tubes and hollow sections shall be made from alloys specified in IS 733. 9.2 The chemical analysis of the material shall be carried out either in accordance with the methods specified in IS 504 (Part 1 to 12) and IS 504 (Part 13 to 16) or by any other established instrumental/chemical method. In case of any dispute the method specified in relevant parts of IS 504 shall be used as referee method. However, when the method is not given in IS 504, the referee method shall be as agreed to between the purchaser and the manufacturer. ")	-	4400	-
10(Tensile test)	-	2200	-
Cl.9.1(Aluminium- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Copper- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Magnesium- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Silicon- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Iron- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Manganese- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Zinc- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Titanium and/ or other grain refining elements- IS 504 and its parts or any other intrumental/chemical methods)	-	300	-
Cl.9.1(Chromium- IS 504 and its parts or any other intrumental/chemical methods)	-	600	-
Cl.9.1(Remarks (Ti+V) - IS 504 and its parts or any other intrumental/chemical methods)	-	600	-
Cl.9.1(Remarks (Cr+Mn) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.9.1(Remarks (Total Impurities)- IS 504 and its parts or any other intrumental/chemical methods)	-	500	-

31 Dec, 2029

-
-

245

IS 4026 (2023)

ALUMINIUM INGOTS BILLETS AND WIRE BARS EC GRADE

Aluminium billets/ingots/wire/bars

6100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(SHAPES AND SIZES)	-	2000	-
9, Table 1, i)(Aluminium, Min)	-	500	-
9, Table 1, ii)(Silicon)	-	200	-
9, Table 1, iii)(Iron)	-	200	-
9, Table 1, iv)(Copper)	-	200	-
9, Table 1, v)(Manganese)	-	200	-
9, Table 1, vi)(Magnesium)	-	200	-
9, Table 1, vii)(Chromium)	-	200	-
9, Table 1, viii)(Zinc)	-	200	-
9, Table 1, ix)(Titanium)	-	200	-
9, Table 1, x)(Boron)	-	200	-
9, Table 1, xi)(Gallium)	-	200	-
9, Table 1, xii)(Zirconium)	-	200	-
9, Table 1, xiii)(Titanium + Vanadium)	-	400	-
9, Table 1, xiv)(Other elements (each))	-	500	-
9, Table 1, xv)(Other elements (Total))	-	500	-

31 Dec, 2029

-
Included w.e.f. 03.04.2024

246

IS 6754 (1972)

Specification for aluminium alloy ingots for bearings

Aluminum alloys ingots

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General requirements)	-	2000	-
3.1(Manufacture)	-	2000	-
4.1(Chemical composition)	-	5600	-
5.1(Shape and size)	-	2400	-
6(Freedom from Defects)	-	1500	-
7(Selection of Sample for chemical analysis)	-	500	-
8(Retest)	-	15000	-
9(Marking)	-	1000	-
Table-1, Clause - 4.1(Copper)	-	300	-
Table-1, Clause - 4.1(Magnesium)	-	300	-
Table-1, Clause - 4.1(Manganese)	-	300	-
Table-1, Clause - 4.1(Titanium)	-	300	-
Table-1, Clause - 4.1(Silicon)	-	300	-
Table-1, Clause - 4.1(Nickel)	-	300	-
Table-1, Clause - 4.1(Tin)	-	300	-
Table-1, Clause - 4.1(Other elements)	-	2000	-
Table-1, Clause - 4.1(Total of Fe+Si+Mn)	-	1000	-
Table-1, Clause - 4.1(Aluminium)	-	500	-

31 Dec, 2029

-
Included w.e.f. 03.04.2024

247

IS 737 (2008)

Wrought aluminium and aluminium alloy sheet and strip for general engineering purposes - Specification (Fourth Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	200	-
6 Table-1(Al)	-	200	-
6 Table-1(Cu)	-	200	-
6 Table-1(Mg)	-	200	-
6 Table-1(Si)	-	200	-
6 Table-1(Fe)	-	200	-
6 Table-1(Mn)	-	200	-
6 Table-1(Zn)	-	200	-
6 Table-1(Ti)	-	200	-
6 Table-1(Cr)	-	200	-
6 Table-1(Cu+Si+Fe)	-	600	-
6 Table-1(Cu+Si+Fe+Mn+Zn)	-	1000	-
6 Table-1(Cu+Mg+Si+Fe+Mn+Zn)	-	1200	-
6 Table-1(Zr)	-	200	-
6 Table-1(Cr+Mn)	-	300	-
7 Table-2(Tensile Strength)	-	1000	-
7 Table-2(Elongation)	-	500	-
7 Table-2(0.2 % Proof Stress)	-	1000	-
7 Table-2(Bend Test)	-	1000	-
9(Dimension - IS 2676)	-	1000	-
12(Marking)	-	200	-

31 Dec, 2029

-
Included w.e.f. 03.04.2024

248

IS 1284 (1975)

Specification for wrought aluminium alloy bolt and screw stock (for general engineering purposes) (Second Revision)

17300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defects)	-	300	-
5.1 Table 1(Copper)	-	500	-
5.1 Table 1(Magnesium)	-	500	-
5.1 Table 1(Silicon)	-	500	-
5.1 Table 1(Iron)	-	500	-
5.1 Table 1(Manganese)	-	500	-
5.1 Table 1(Zinc)	-	500	-
5.1 Table 1(Titanium and/or other grain refining elements)	-	500	-
5.1 Table 1(Chromium)	-	500	-
5.1 Table 2(Diameter)	-	500	-
5.1 Table 2(0.2 percent proof stress)	-	3000	-
5.1 Table 2(Tensile strength)	-	3000	-
6(Dimensions and tolerances)	-	1000	-
8.1(Tensile test)	-	3000	-
8.2(Head-Forming test)	-	2000	-
10(Marking)	-	500	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

249

IS 2681 (1993)

Non - Ferrous metal sliding door bolts (Aldrops) for use with padlocks - Specification (Third Revision)

NON FERROUS METAL

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1(Brass sliding door bolts shall have satin finish or shall be polished or plated as specified by the purchaser)	-	1000	-
Cl. 8.2 (Ref. Cl. 11.1 of IS 1868:1996)( appearance and Colour - shall be free from visible defects on the significant surface(s) when viewed from an agreed distance)	-	2000	-
Cl. 8.2 (Ref. Cl.9 of IS 1868:1996)(Aluminium shall be anodized to a bright, natural, sat or satin finish or dyed. )	-	2000	-
Cl. 8.2 (Ref. Cl.9 of IS 1868:1996)(Anodinc casting thickness (Cl. 9.2 of IS 1868:1996))	-	2000	-
3(TYPES)	-	500	-
4(SIZES)	-	500	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-A)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-B)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-C)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-D)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-E)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-F)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-G)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-H)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-J)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-K)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-L)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-M)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-N)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-Q)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-S)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-T)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-W)	-	300	-
6.1-Total 2(DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 8)	-	1000	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-A)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-B)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-C)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-D)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-E)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-F)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-G)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-H)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-J)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-K)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-L)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-M)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-Pin dia)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-R)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-T)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-U)	-	300	-
6.1-Table 3(DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 8)	-	1000	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.2(MANUFACTURE-Brass Sliding Door Bolts or Aluminium Alloy Sliding Door Bolts)	-	500	-
7.2(MANUFACTURE-Brass Sliding Door Bolts or Aluminium Alloy Sliding Door Bolts)	-	500	-
8.1(FINISH)	-	1000	-
8.2(FINISH)	-	1000	-
8.2(FINISH-anodic casting -Min Avg thickness)	-	2000	-
8.2(FINISH-anodic casting -Min Local thickness)	-	2000	-
7.2(Brass/Aluminium alloy door bolt)	-	500	-
7.2(Aluminium alloy door bolt)	-	500	-
7.1(General)	-	500	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
4.0(Sizes)	-	500	-
3.1(Sliding Door Bolts)	-	500	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-
6.1 Fig 1 & Table 3(Dimensions & Tolerances)	-	300	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

250

IS 281 (2009)

Mild steel sliding door bolts for use with padlocks - Specification (Fourth Revision)

100 mm - 500mm

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	1500	-
Cl. 8.2 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	1500	-
3(TYPES)	-	500	-
4(SIZES)	-	500	-
6(DIMENSIONS AND TOLERANCES-A)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-A)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-B)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-C)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-D)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-E)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-F)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-G)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-H)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-J)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-T)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 (IS 451))	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on bolts plates)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on Socket)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on bolt)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Socket)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Staple)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for plate and sockets)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for Staple)	-	900	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
8.1(FINISH-Sliding Bolts, Plate Type)	-	1500	-
Cl. 8.1 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	1500	-
Cl. 8.2 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	1500	-
3(TYPES)	-	500	-
4(SIZES)	-	500	-
6(DIMENSIONS AND TOLERANCES-A)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-A)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-B)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-C)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-D)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-E)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-F)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-G)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-H)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-J)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-T)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 (IS 451))	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on bolts plates)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on Socket)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on bolt)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Socket)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Staple)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for plate and sockets)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for Staple)	-	900	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
8.1(FINISH-Sliding Bolts, Plate Type)	-	1500	-
5.1.2(Bend test)	-	500	-
5.2.1(Tensile test)	-	1500	-
Cl. 8.1 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	1500	-
Cl. 8.2 (Ref. Cl.9 of IS 1868:1996)(Thickness Test for Copper Plating of Oxidized Finished Material, Cl. 4 of IS 1378 : 1987 & Cl 3 of IS 3203)	-	1500	-
3(TYPES)	-	500	-
4(SIZES)	-	500	-
6(DIMENSIONS AND TOLERANCES-A)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-A)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-B)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-C)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-D)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-E)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-F)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-G)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-H)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-J)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-T)	-	300	-
6-Table 1(DIMENSIONS AND TOLERANCES-DIMENSIONS AND TOLERANCES-No. of Screw on Staple or Clip to accommodate Wood Screw N0 (IS 451))	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on bolts plates)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Rivets on Socket)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on bolt)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Socket)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-No. of Screw holes on Staple)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for plate and sockets)	-	900	-
6-Table 1(DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for Staple)	-	900	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.1(MANUFACTURE-General)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.2(MANUFACTURE-Sliding Door Bolts, Plate Type)	-	500	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
7.3(MANUFACTURE-Sliding Bolts, Clip or Bolt Type)	-	5000	-
8.1(FINISH-Sliding Bolts, Plate Type)	-	1500	-
5.1.2(Bend test)	-	1000	-
5.2.1(Tensile test)	-	1500	-
5.2.2(Bend Test)	-	1000	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

251

IS 10238 (2001)

Fasteners - Threaded steel fasteners - Step bolts for steel structures - Specification (First Revision)

Grade C

24000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(GRADES)	-	500	-
5(MECHANICAL PROPERTIES)	-	17200	-
6-6.1(Nuts)	-	1000	-
6-6.2.1(Washers)	-	1000	-
6-.6.2.2(Washers)	-	1000	-
7(GENERAL REQUIREMENTS)	-	500	-
8.1(FINISH)	-	500	-
8.2()	-	500	-
8.3()	-	500	-
9(SAMPLING, INSPECTION AND ACCEPTANCE CRITERIA)	-	100	-
10.1.1(TESTS)	-	1000	-
12(MARKING)	-	100	-
13(PACKAGING)	-	100	-
4(GRADES)	-	500	-
5(MECHANICAL PROPERTIES)	-	17200	-
6-6.1(Nuts)	-	1000	-
6-6.2.1(Washers)	-	1000	-
6-.6.2.2(Washers)	-	1000	-
7(GENERAL REQUIREMENTS)	-	500	-
8.1(FINISH)	-	500	-
8.2()	-	500	-
8.3()	-	500	-
9(SAMPLING, INSPECTION AND ACCEPTANCE CRITERIA)	-	100	-
10.1.1(TESTS)	-	1000	-
12(MARKING)	-	100	-
13(PACKAGING)	-	100	-
Table 3 (i)(Tensile strength, Rm, MPa)	-	1500	-
Table 3 (ii)(Lower yield strength)	-	1000	-
Table 3 (iii)(Stress at 0,2 % non-proportional elongation)	-	500	-
table 3 (iv)(Stress at 0,0048d non-proportional elongation for full-size fasteners)	-	500	-
Table 3 (v)((i) Stress under proof load (ii) Proof strength ratio)	-	500	-
Table (vi)(Percentage elongation after fracture for machined test pieces)	-	500	-
Table 3 (vii)(Percentage reduction of area after fracture for machined test pieces,)	-	500	-
Table 3 (viii)(Elongation after fracture for full-size fasteners,)	-	500	-
Table 3 (ix)(Head soundness)	-	1500	-
Table 3 (x)(Vickers hardness)	-	500	-
table 3 (xi)(Brinell hardness)	-	500	-
table 3()	-	100	-
table 3 (xii)(Rockwell hardness, HRB Rockwell hardness, HRC)	-	500	-
Table 3 (xiv)(Surface hardness)	-	500	-
Table 3 (xv)(Height of non-decarburized thread zone,)	-	500	-
Table 3 (xv)(Height of non-decarburized thread zone, Depth of complete decarburization in the thread,)	-	500	-
table 3 (xvi)(Reduction of hardness after retempering HV)	-	500	-
table 3 (xvii)(Breaking torque)	-	1600	-
table 3 (xviii)(Impact strength, KV)	-	3000	-
Table3 (xix)(Surface integrity in accordance with)	-	1000	-
table 3 (xvii)(Breaking torque Nm)	-	1600	-
3(DIMENSIONS AND TOLERANCES)	-	1000	-
4(GRADES)	-	500	-
5(MECHANICAL PROPERTIES)	-	17200	-
6-6.1(Nuts)	-	1000	-
6-6.2.1(Washers)	-	1000	-
6-.6.2.2(Washers)	-	1000	-
7(GENERAL REQUIREMENTS)	-	500	-
8.1(FINISH)	-	500	-
8.2()	-	500	-
8.3()	-	500	-
9(SAMPLING, INSPECTION AND ACCEPTANCE CRITERIA)	-	100	-
10.1.1(TESTS)	-	1000	-
12(MARKING)	-	100	-
13(PACKAGING)	-	100	-
Table 3 (i)(Tensile strength, Rm, MPa)	-	1500	-
Table 3 (ii)(Lower yield strength)	-	1000	-
Table 3 (iii)(Stress at 0,2 % non-proportional elongation)	-	500	-
table 3 (iv)(Stress at 0,0048d non-proportional elongation for full-size fasteners)	-	500	-
Table 3 (v)((i) Stress under proof load (ii) Proof strength ratio)	-	500	-
Table (vi)(Percentage elongation after fracture for machined test pieces)	-	500	-
Table 3 (vii)(Percentage reduction of area after fracture for machined test pieces,)	-	500	-
Table 3 (viii)(Elongation after fracture for full-size fasteners,)	-	500	-
Table 3 (ix)(Head soundness)	-	1500	-
Table 3 (x)(Vickers hardness)	-	500	-
table 3 (xi)(Brinell hardness)	-	500	-
table 3()	-	100	-
table 3 (xii)(Rockwell hardness, HRB Rockwell hardness, HRC)	-	500	-
Table 3 (xiv)(Surface hardness)	-	500	-
Table 3 (xv)(Height of non-decarburized thread zone,)	-	500	-
Table 3 (xv)(Height of non-decarburized thread zone, Depth of complete decarburization in the thread,)	-	500	-
table 3 (xvi)(Reduction of hardness after retempering HV)	-	500	-
table 3 (xvii)(Breaking torque)	-	1600	-
table 3 (xviii)(Impact strength, KV)	-	3000	-
Table3 (xix)(Surface integrity in accordance with)	-	1000	-
table 3 (xvii)(Breaking torque Nm)	-	1600	-
3(DIMENSIONS AND TOLERANCES)	-	1000	-
4(GRADES)	-	500	-
5(MECHANICAL PROPERTIES)	-	17200	-
6-6.1(Nuts)	-	1000	-
6-6.2.1(Washers)	-	1000	-
6-.6.2.2(Washers)	-	1000	-
7(GENERAL REQUIREMENTS)	-	500	-
8.1(FINISH)	-	500	-
8.2()	-	500	-
8.3()	-	500	-
9(SAMPLING, INSPECTION AND ACCEPTANCE CRITERIA)	-	100	-
10.1.1(TESTS)	-	1000	-
12(MARKING)	-	100	-
13(PACKAGING)	-	100	-
Table 3 (i)(Tensile strength, Rm, MPa)	-	1500	-
Table 3 (ii)(Lower yield strength)	-	1000	-
Table 3 (iii)(Stress at 0,2 % non-proportional elongation)	-	500	-
table 3 (iv)(Stress at 0,0048d non-proportional elongation for full-size fasteners)	-	500	-
Table 3 (v)((i) Stress under proof load (ii) Proof strength ratio)	-	500	-
Table (vi)(Percentage elongation after fracture for machined test pieces)	-	500	-
Table 3 (vii)(Percentage reduction of area after fracture for machined test pieces,)	-	500	-
Table 3 (viii)(Elongation after fracture for full-size fasteners,)	-	500	-
Table 3 (ix)(Head soundness)	-	1500	-
Table 3 (x)(Vickers hardness)	-	500	-
table 3 (xi)(Brinell hardness)	-	500	-
table 3()	-	100	-
table 3 (xii)(Rockwell hardness, HRB Rockwell hardness, HRC)	-	500	-
Table 3 (xiv)(Surface hardness)	-	500	-
Table 3 (xv)(Height of non-decarburized thread zone,)	-	500	-
Table 3 (xv)(Height of non-decarburized thread zone, Depth of complete decarburization in the thread,)	-	500	-
table 3 (xvi)(Reduction of hardness after retempering HV)	-	500	-
table 3 (xvii)(Breaking torque)	-	1600	-
table 3 (xviii)(Impact strength, KV)	-	3000	-
Table3 (xix)(Surface integrity in accordance with)	-	1000	-
table 3 (xvii)(Breaking torque Nm)	-	1600	-
3(DIMENSIONS AND TOLERANCES)	-	1000	-
CL 3(Dimensions and Tolerances)	-	1000	-
5(Torsion test)	-	1600	-
CL 8(Finish)	-	500	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

252

IS 5187 (1972)

Specification for flush bolts (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 2.1 Table 1(i)(Body and plate)	-	2000	-
Clause 2.1 Table 1(ii)(Bolt)	-	2000	-
Clause 2.1 Table 1(iii)(Spring)	-	5000	-
Clause 3(Types, sizes and shape)	-	3000	-
Clause 5.1(Dimension)	-	3000	-
Clause 5.2(Tolerance)	-	1000	-
Clause 6(Workmanship and finish)	-	3000	-
Clause 7(Marking)	-	500	-
Clause 8(Packing)	-	500	-

31 Dec, 2029

-
Included w.e.f. 03.04.2024

253

IS 4621 (1975)

Specification for indicating bolts for use in public baths and lavatories (First Revision)

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4(DIMENSIONS AND TOLERANCES)	-	4000	-
Clause 7(WORKMANSHIP AND FINISH)	-	3000	-
Clause 4.1(Dimension and tolerance)	-	4000	-
Clause 5.2 Table 2(i)(Body, knob and indicating spindle)	-	3000	-
Clause 5.2 Table 2(ii)(Indicating disc)	-	3000	-
Clause 5.2 Table 2(iii)(Gears)	-	3000	-
Clause 7(Workmanship and finish)	-	3000	-
Clause 8(Marking)	-	400	-
Clause 9(Packing)	-	400	-
Clause 4(DIMENSIONS AND TOLERANCES)	-	4000	-
Clause 7(WORKMANSHIP AND FINISH)	-	3000	-
Clause 4.1(Dimension and tolerance)	-	4000	-
Clause 5.2 Table 2(i)(Body, knob and indicating spindle)	-	3000	-
Clause 5.2 Table 2(ii)(Indicating disc)	-	3000	-
Clause 5.2 Table 2(iii)(Gears)	-	3000	-
Clause 7(Workmanship and finish)	-	3000	-
Clause 8(Marking)	-	400	-
Clause 9(Packing)	-	400	-
Cl-6(Manufacture)	-	200	-

31 Dec, 2029

-
Included w.e.f. 03.04.2024 Exclusion: Cl.5.2 Table 2 (i) (Body, knob and indicating spindle)- Raw Material

254

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

63400 WP,63400P,65032WP,CuZn40,CB-2,TYPE-II

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Titanium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - others - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Copper - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Lead - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Zinc- IS 3685:1966)	-	300	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	300	-
5.2.2 Table 2(Particulars-Skeleton Tower Bolts)	-	300	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-	1000	-
6.1- Table 1(Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-	1000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Titanium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - others - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Copper - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Lead - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Zinc- IS 3685:1966)	-	300	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	300	-
5.2.2 Table 2(Particulars-Skeleton Tower Bolts)	-	300	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-	1000	-
6.1- Table 1(Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-	1000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Titanium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - others - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Copper - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Lead - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Zinc- IS 3685:1966)	-	300	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	300	-
5.2.2 Table 2(Particulars-Skeleton Tower Bolts)	-	300	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-	1000	-
6.1- Table 1(Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-	1000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Titanium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - others - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Copper - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Lead - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Zinc- IS 3685:1966)	-	300	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	300	-
5.2.2 Table 2(Particulars-Skeleton Tower Bolts)	-	300	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-	1000	-
6.1- Table 1(Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-	1000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Aluminium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Magnesium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Copper- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Iron- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Lead- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964)	-	3500	-
5.1(General)	-	500	-
6.2- Table 3(PACKING)	-	100	-
7(Finish)	-	2500	-
8(Packing)	-	100	-
9(Scale of sampling)	-	100	-
10(Marking)	-	100	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Titanium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - others - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Aluminium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Copper - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Magnesium - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Silicon - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Iron - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Manganese - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Zinc - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1 , Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Titanium and or other grain refining elements - IS 504)	-	300	-
4 -Table 3- ii (Ref. Cl 5.1, Table 1 Designation 65032 of IS 733 : 1983)(Chemical composition - Chromium - IS 504)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	300	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	300	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Zinc - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Copper - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Lead - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Total other impurities excluding iron - IS 3685:1966)	-	300	-
4 -Table 3- v (Ref. Cl 8.1, Table 1 Grade II of IS 319 : 1974)(Chemical composition - Zinc- IS 3685:1966)	-	300	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	300	-
5.2.2 Table 2(Particulars-Skeleton Tower Bolts)	-	300	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-	1000	-
6.1- Table 1(Dimension of barrel tower bolts-Minimum No. of equally Spaced holes in Barrel & Socket for wooden screw no 6)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	1000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 4)	-	1000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Aluminium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Magnesium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Copper- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Iron- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Lead- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964)	-	3500	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964)	-	3500	-
5.1(General)	-	500	-
6.2- Table 3(PACKING)	-	100	-
7(Finish)	-	2500	-
8(Packing)	-	100	-
9(Scale of sampling)	-	100	-
10(Marking)	-	100	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

255

IS 204 : Part 1 (1991)

Tower bolts - Specification: Part 1 ferrous metals (Fifth Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Carbon - IS 228)	-	300	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Manganese - IS 228)	-	300	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Phosphorus - IS 228)	-	300	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Sulphur - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Carbon Equivalen(CE) - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Carbon - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Manganese - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Sulphur - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Phosphorus - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Silicon - IS 228)	-	300	-
4 -Table 5- iii (Ref. Cl 6.1 of IS 210 : 2009)(Chemical composition - Sulphur and/or Phosphorous)	-	3000	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G )	-	1000	-
6.2- Table 2(Dimension of Sami Barrel Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Bolt Plate or Socket-F 8.Dia of bore of Bolt Plate or socket G )	-	1000	-
6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts- 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7. Length of Strap-E" 8.Thickness of Back Plate -F 9.Thickness of Socket or Upper Plate and Strap- F" 10.Dia of bore of Bolt Plate or socket- G 11. Length of Alternative Socket-H )	-	1000	-
6.4- Table 4(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Staple -F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob-J)	-	1000	-
6.1- Table 1(Dimension of Barrel tower bolts-Minimum No. of equally Spaced Screw holes in Barrel and Socket for wood screw no 6)	-	1000	-
6.2- Table 2(Dimension of Sami Barrel Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-	1000	-
6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-	1000	-
6.4- Table 4(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	1000	-
6.4- Table 4(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 6)	-	1000	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Carbon - IS 228)	-	300	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Manganese - IS 228)	-	300	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Phosphorus - IS 228)	-	300	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Sulphur - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Carbon Equivalen(CE) - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Carbon - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Manganese - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Sulphur - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Phosphorus - IS 228)	-	300	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Silicon - IS 228)	-	300	-
4 -Table 5- iii (Ref. Cl 6.1 of IS 210 : 2009)(Chemical composition - Sulphur and/or Phosphorous)	-	3000	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G )	-	1000	-
6.2- Table 2(Dimension of Sami Barrel Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Bolt Plate or Socket-F 8.Dia of bore of Bolt Plate or socket G )	-	1000	-
6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts- 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Socket-E 7. Length of Strap-E" 8.Thickness of Back Plate -F 9.Thickness of Socket or Upper Plate and Strap- F" 10.Dia of bore of Bolt Plate or socket- G 11. Length of Alternative Socket-H )	-	1000	-
6.4- Table 4(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt-A 3.Length of Bolt Plate-B 4.Width of Bolt Plate-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Staple -F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob-J)	-	1000	-
6.1- Table 1(Dimension of Barrel tower bolts-Minimum No. of equally Spaced Screw holes in Barrel and Socket for wood screw no 6)	-	1000	-
6.2- Table 2(Dimension of Sami Barrel Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-	1000	-
6.3- Table 3(Dimension of Riveted or Spot Welded Tower Bolts-Minimum No. of equally Spaced Screw holes in Bolt Plate and Socket for wood screw no 6)	-	1000	-
6.4- Table 4(Dimension of Skeleton Tower Bolts- Nos of Staples)	-	1000	-
6.4- Table 4(Dimension of Skeleton Tower Bolts-Minimum No. of Screw holes for wood screw no 6)	-	1000	-
4 -Table 5- iii (Ref. Cl 9.1 of IS 210 : 2009)(The microstructure shall be substantially free of primary cementite and/ or massive stead ite and shall consist oftlake graphite in a matrix offerrite or pearlite or mixture thereof.)	-	2000	-
4 -Table 5- iii (Ref. Cl 9.1.1 of IS 210 : 2009)(Graphite structute Distribution - IS 7754)	-	2000	-
5.1(General)	-	100	-
5.2.1 Table 1(Particulars-Barrel Tower Bolts)	-	1000	-
5.2.2 Table 2(Particulars-Sami Barrel Tower Bolts)	-	1000	-
5.2.3 Table 3(Particulars-Riveted or Spot Welded Tower Bolts)	-	1000	-
5.2.4 Table 4(Particulars-Skeleton Tower Bolts)	-	1000	-
8.1(MARKING- .)	-	100	-
8.1.1,(MARKING- )	-	100	-
9(PACKING)	-	100	-
7(Finish)	-	1700	-

31 Dec, 2029

-
Included w.e.f. 04.04.2024

256

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	600	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.4.1 (b)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	600	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.4.2(a)( Aggregates Impact Value)	-	600	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.4.2(b)( Aggregates Impact Value)	-	600	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.4.3(a)( Aggregate Abrasion Value)	-	400	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.4.3(b)( Aggregate Abrasion Value)	-	400	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Nominal Size of aggregate)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Class)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Size)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(i)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 160 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(i)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 80 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(ii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 80 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(ii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 40 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(iii)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 20 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 4.75 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.1.1-Table 8(iv)(SIZE AND GRADING OF AGGREGATES- Sizes of Coarse Aggregates for Mass Concrete- Percentage Passing through 2.36 mm Sieve)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Grading Zone)	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.4-Table 10(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Nominal Size )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.4-Table 10(i)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 80mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.4-Table 10(ii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 40mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.4-Table 10(iii)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 20mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.4-Table 10(iv)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 4.75mm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.4-Table 10(v)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 600µm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.7-Table-3-(III) IS:14959 (P-2)(Water soluble chloride content (fine aggregate))	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.7-Table-3-(II) IS:4032(Total sulphate content (fine aggregate))	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
Clause 5.7- Table 3 (i) (TotalAlkali content as Na2O equivalent )	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.5-IS: 2386 (P-5)(Soundness (fine aggregate))	-	2000	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.6-IS: 2386 (P-7)(Alkali Aggregate Reaction (fine aggregate))	-	500	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
Clause 5.6(Dissolved Silica)	-	250	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
Clause 5.6(Reduction in Alkalinity)	-	250	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-
5.5-IS: 2386 (P-5)(Soundness (coarse aggregate))	-	2000	FOR COARSE AGGREGATE 12500/- & FINE AGGREGATE 9000/-

31 Dec, 2029

-
-

257

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

5100 View breakup
Total testing chsrges-Rs.5100/- .In case of water failure (concrete cube)-Rs.2000/-(40% discount to BIS)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4-Table-1 (v)-IS: 3025(P-17)(Suspended matter)	-	400	-
5.4-Table-1 (iv)-IS: 3025(P-32)(Chloride)	-	400	-
5.4-Table-1 (ii)-IS: 3025(P-24)(Sulphate)	-	400	-
5.4-Table-1 (i)-IS: 3025(P-18)(In-Organic)	-	400	-
5.4-Table-1 (i)-IS: 3025(P-18)(Organic )	-	400	-
5.4.2-IS: 3025(P-11)(Ph)	-	400	-
Cl 5.4 (b)(Alkalinity)	-	400	-
Cl 5.4 (a)(Acidity)	-	300	-
16.1(Compressive Strength of Individual Samples )	-	1000	-
16.1(Average Compressive Strength)	-	1000	-

31 Dec, 2029

-
-

258

IS 4454 : Part 1 (2001)

Steel wire for mechanical springs - Specification: Part 1 cold drawn unalloyed steel wire (Third Revision)

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	500	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	8000	-
7.1, 7.2(copper)	-	250	-
7.1, 7.2(Vanadium)	-	250	-
7.1, 7.2(phosphorus)	-	250	-
7.1, 7.2(sulphur)	-	250	-
7.1, 7.2(manganese)	-	250	-
7.1, 7.2(silicon )	-	250	-
7.1, 7.2(carbon)	-	250	-
7.1, 7.2(Chromium)	-	250	-
Cl 8(Workmanship)	-	500	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test & Decarburization Test)	-	8000	-

31 Dec, 2029

-
-

259

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

5850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 4.1(Workmanship)	-	50	-
Cl 5 & 6(Diameter)	-	50	-
Cl 7(UTM)	-	1000	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	450	-
Clause 3.1.1(Sulphur)	-	250	-
Clause 3.1.1(Phosphorus)	-	250	-
Cl. 7.1(Elongation)	-	500	-
Cl. 7.1(Proof Stress 0.2 %)	-	500	-
Cl. 6.2(Length)	-	100	-
Clause 3(Nitrogen)	-	1400	-
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	300	-
Clause 7.1(Ultimate Tensile Stress)	-	1000	-
Cl 4.1(Workmanship)	-	50	-
Cl 5 & 6(Diameter)	-	50	-
Cl 7(UTM)	-	1000	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	450	-
Clause 3.1.1(Sulphur)	-	250	-
Clause 3.1.1(Phosphorus)	-	250	-
Cl. 7.1(Elongation)	-	500	-
Cl. 7.1(Proof Stress 0.2 %)	-	500	-
Cl. 6.2(Length)	-	100	-
Clause 3(Nitrogen)	-	1400	-
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	300	-
Clause 7.1(Ultimate Tensile Stress)	-	1000	-
Cl 4.1(Workmanship)	-	50	-
Cl 5 & 6(Diameter)	-	50	-
Cl 7(UTM)	-	1000	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	450	-
Clause 3.1.1(Sulphur)	-	250	-
Clause 3.1.1(Phosphorus)	-	250	-
Cl. 7.1(Elongation)	-	500	-
Cl. 7.1(Proof Stress 0.2 %)	-	500	-
Cl. 6.2(Length)	-	100	-
Clause 3(Nitrogen)	-	1400	-
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	300	-
Clause 7.1(Ultimate Tensile Stress)	-	1000	-
Cl 4.1(Workmanship)	-	50	-
Cl 5 & 6(Diameter)	-	50	-
Cl 7(UTM)	-	1000	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	450	-
Clause 3.1.1(Sulphur)	-	250	-
Clause 3.1.1(Phosphorus)	-	250	-
Cl. 7.1(Elongation)	-	500	-
Cl. 7.1(Proof Stress 0.2 %)	-	500	-
Cl. 6.2(Length)	-	100	-
Clause 3(Nitrogen)	-	1400	-
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	300	-
Clause 7.1(Ultimate Tensile Stress)	-	1000	-
Cl 4.1(Workmanship)	-	-	-
Cl 5 & 6(Diameter)	-	-	-
Cl 7(UTM)	-	-	-
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	-	-
Clause 3.1.1(Sulphur)	-	-	-
Clause 3.1.1(Phosphorus)	-	-	-
Cl. 7.1(Elongation)	-	-	-
Cl. 7.1(Proof Stress 0.2 %)	-	-	-
Cl. 6.2(Length)	-	-	-
Clause 3(Nitrogen)	-	-	-
Clause 7.1(Total Elongation over a gauge length of 8 D Where D is the dia of wire)	-	-	-
Clause 7.1(Ultimate Tensile Stress)	-	-	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

260

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

3150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	200	-
Cl 6.2(Diameter & Ovality)	-	200	-
Cl 6.2(Weight)	-	200	-
Cl 8.2(Bend test)	-	500	-
Cl 9.3(Press)	-	500	-
Cl 6.1(Diameter)	-	200	-
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	1500	-
Cl 8(Physical Requirements)	-	1500	-
Clause -4, 4.3(TITANIUM)	-	100	-
Clause -4, 4.2(VANADIUM)	-	100	-
Clause -4, 4.1(NIOBIUM)	-	100	-
Clause -4, 4.1(Molybdenum)	-	100	-
Clause -4, 4.1(Chromium)	-	100	-
Clause -4, 4.1(Nickel)	-	100	-
Clause -4, 4.1( ALUMINIUM)	-	100	-
Clause -4, 4.1(SILICON)	-	100	-
Clause -4, 4.1(NITROGEN)	-	1400	-
Clause -4, 4.1(MANGANESE)	-	100	-
Clause -4, 4.1(PHOSPHURS)	-	100	-
Clause -4, 4.1(SULPHUR)	-	100	-
Clause -4, 4.1( CARBON)	-	100	-
Cl. 8.1 Table 1(Elongation)	-	500	-
Clause 8.1(Yield Stress)	-	500	-
Clause 9.3(Bend test)	-	500	-
Clause 6.1(Size)	-	200	-
Cl 9.3(Press)	-	500	-
Cl 8(UTM)	-	1500	-
Clause 5.1(IS 432 Part 1)	-	100	-
Clause 6.2(IS 1732)	-	200	-
Clause 8.1(IS 1608 Part 1)	-	1500	-
Clause 4(Any Instrumental Method/Chemical Method)	-	1000	-
Clause 5.1(Freedom from Defect)	-	100	-
Clause 4(Boron)	-	100	-
Clause 4(Copper)	-	100	-
Cl 5.1(Workmanship)	-	200	-
Cl 6.2(Diameter & Ovality)	-	200	-
Cl 6.2(Weight)	-	200	-
Cl 8.2(Bend test)	-	500	-
Cl 9.3(Press)	-	500	-
Cl 6.1(Diameter)	-	200	-
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	1500	-
Cl 8(Physical Requirements)	-	1500	-
Cl. 8.1 Table 1(Elongation)	-	1500	-
Clause 8.1(Yield Stress)	-	1500	-
Clause 9.3(Bend test)	-	500	-
Clause 6.1(Size)	-	200	-
Cl 9.3(Press)	-	500	-
Cl 8(UTM)	-	1500	-
Clause 5.1(IS 432 Part 1)	-	100	-
Clause 6.2(IS 1732)	-	200	-
Clause 8.1(IS 1608 Part 1)	-	1500	-
Clause 4(Any Instrumental Method/Chemical Method)	-	100	-
Clause 5.1(Freedom from Defect)	-	100	-
Clause 4(Boron)	-	100	-
Clause 4(Copper)	-	100	-
Cl 5.1(Workmanship)	-	200	-
Cl 6.2(Diameter & Ovality)	-	200	-
Cl 6.2(Weight)	-	200	-
Cl 8.2(Bend test)	-	500	-
Cl 9.3(Press)	-	500	-
Cl 6.1(Diameter)	-	200	-
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	1500	-
Cl 8(Physical Requirements)	-	1500	-
Cl. 8.1 Table 1(Elongation)	-	500	-
Clause 8.1(Yield Stress)	-	500	-
Clause 9.3(Bend test)	-	500	-
Clause 6.1(Size)	-	200	-
Cl 9.3(Press)	-	500	-
Cl 8(UTM)	-	1500	-
Clause 5.1(IS 432 Part 1)	-	200	-
Clause 6.2(IS 1732)	-	200	-
Clause 8.1(IS 1608 Part 1)	-	1500	-
Clause 4(Any Instrumental Method/Chemical Method)	-	1000	-
Clause 5.1(Freedom from Defect)	-	200	-
Clause 4(Boron)	-	100	-
Clause 4(Copper)	-	100	-

31 Dec, 2029

-
-

261

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

7800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	200	BIS 10 % discount
Cl 9(Tensile Test On UTM)	-	1500	BIS 10 % discount
Cl 11(Workmanship)	-	100	BIS 10 % discount
Cl 13(Workmanship)	-	100	BIS 10 % discount
6 AND AS PER IS 7887(MICRO ALLOY)	-	500	BIS 10 % discount
6 AND AS PER IS 7887(ALUMINIUM)	-	200	BIS 10 % discount
6 AND AS PER IS 7887(PHOSPHORUS)	-	100	BIS 10 % discount
6 AND AS PER IS 7887(SULPHUR)	-	200	BIS 10 % discount
6 AND AS PER IS 7887(MANGANESE)	-	200	BIS 10 % discount
6 AND AS PER IS 7887(SILICON)	-	200	BIS 10 % discount
6 AND AS PER IS 7887(CARBON)	-	200	BIS 10 % discount
7 & 8(Ovality)	-	500	BIS 10 % discount
7 & 8(Diameter)	-	200	BIS 10 % discount
9.2(Wrapping Test)	-	1000	BIS 10 % discount
9.3(Bend test)	-	1000	BIS 10 % discount
10(Finish)	-	200	BIS 10 % discount
11(Coating test)	-	1000	BIS 10 % discount
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	100	BIS 10 % discount
Clause 6 and Note 3 of IS 7887(Copper)	-	200	BIS 10 % discount
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	200	BIS 10 % discount
Cl 9(Tensile Test On UTM)	-	1500	BIS 10 % discount
Cl 11(Workmanship)	-	1000	BIS 10 % discount
Cl 13(Workmanship)	-	100	BIS 10 % discount
9.3(Bend test)	-	1000	BIS 10 % discount
10(Finish)	-	200	BIS 10 % discount
11(Coating test)	-	1000	BIS 10 % discount
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	300	BIS 10 % discount
Clause 6 and Note 3 of IS 7887(Copper)	-	200	BIS 10 % discount

31 Dec, 2029

-
Included w.e.f. 07.11.2023

262

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.0(Freedom from defects)	-	200	-
7.0(Dimension and Tolerances)	-	300	-
8.1 Table 1(Cu)	-	200	-
8.1 Table 1(Pb)	-	200	-
8.1 Table 1(Fe)	-	200	-
8.1 Table 1(Total other impurities excluding iron)	-	200	-
8.1 Table 1(Zn)	-	200	-
9.1 Table-2(Tensile Strength)	-	1000	-
9.1 Table-2(Elongation)	-	500	-
9.2(Vickers Hardness)	-	1000	-
10.1(Mercurous Nitrate Test)	-	1000	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

263

IS 318 (1981)

Specification for leaded tin bronze ingots and castings (Second Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(SIZE AND SHAPE)	-	1000	-
6(FREEDOM FROM DEFECTS)	-	500	-
4, Table 2.(MECHANICAL PROPERTIES)	-	1000	-
3, Table 1.(CHEMlCAL COMPOSITION)	-	1000	-
7.2(Dimension)	-	500	-
7.1(Mass)	-	500	-
6.2(Freedom from defects-Castings)	-	500	-
6.1(Freedom from defects-Ingots)	-	500	-
4.1, Table 2(Elongation)	-	500	-
4.1, Table 2(0.2% Proof stress)	-	1000	-
4.1, Table 2(Tensile strength)	-	1000	-
7(SIZE AND SHAPE)	-	1000	-
6(FREEDOM FROM DEFECTS)	-	500	-
4, Table 2.(MECHANICAL PROPERTIES)	-	1000	-
3, Table 1.(CHEMlCAL COMPOSITION)	-	1000	-
7.2(Dimension)	-	500	-
7.1(Mass)	-	500	-
6.2(Freedom from defects-Castings)	-	500	-
6.1(Freedom from defects-Ingots)	-	500	-
4.1, Table 2(Elongation)	-	500	-
4.1, Table 2(0.2% Proof stress)	-	1000	-
4.1, Table 2(Tensile strength)	-	1000	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

264

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Type A/Type B)	-	100	-
5 Table-1(Sizes Diameter of Line wire)	-	100	-
5 Table-1(Sizes Diamater of Point wire)	-	100	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	100	-
5 Table-1(Sizes Distance between two barbs)	-	100	-
7.1(Manufacture)	-	50	-
7.2(Manufacture)	-	50	-
7.3(Manufacture)	-	50	-
8(CHROMATING)	-	200	-
9.1(Freedom from defects)	-	50	-
9.2(Freedom from defects)	-	100	-
12.1(Tensile Strength)	-	450	-
12.1(Breaking load)	-	450	-
12.2.1(Mass of zinc coating (line wire))	-	300	-
12.2.2(Mass of zinc coating (point wire))	-	200	-
12.2(Uniformity of zinc coating)	-	100	-
12.3(Ductility)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.2(Cut Angle)	-	100	-
Cl. 7.2(Length of Barbs)	-	100	-
Cl. 7.2(Finishing of Barbs)	-	100	-
Cl. 7.1(General)	-	100	-
4(Type A/Type B)	-	100	-
5 Table-1(Sizes Diameter of Line wire)	-	100	-
5 Table-1(Sizes Diamater of Point wire)	-	100	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	100	-
5 Table-1(Sizes Distance between two barbs)	-	100	-
7.1(Manufacture)	-	50	-
7.2(Manufacture)	-	50	-
7.3(Manufacture)	-	50	-
8(CHROMATING)	-	200	-
9.1(Freedom from defects)	-	50	-
9.2(Freedom from defects)	-	100	-
12.1(Tensile Strength)	-	450	-
12.1(Breaking load)	-	450	-
12.2.1(Mass of zinc coating (line wire))	-	300	-
12.2.2(Mass of zinc coating (point wire))	-	200	-
12.2(Uniformity of zinc coating)	-	100	-
12.3(Ductility)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.2(Cut Angle)	-	100	-
Cl. 7.2(Length of Barbs)	-	100	-
Cl. 7.2(Finishing of Barbs)	-	100	-
Cl. 7.1(General)	-	100	-
4(Type A/Type B)	-	100	-
5 Table-1(Sizes Diameter of Line wire)	-	100	-
5 Table-1(Sizes Diamater of Point wire)	-	100	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	100	-
5 Table-1(Sizes Distance between two barbs)	-	100	-
7.1(Manufacture)	-	50	-
7.2(Manufacture)	-	50	-
7.3(Manufacture)	-	50	-
8(CHROMATING)	-	200	-
9.1(Freedom from defects)	-	100	-
9.2(Freedom from defects)	-	500	-
12.1(Tensile Strength)	-	450	-
12.1(Breaking load)	-	450	-
12.2.1(Mass of zinc coating (line wire))	-	300	-
12.2.2(Mass of zinc coating (point wire))	-	200	-
12.2(Uniformity of zinc coating)	-	100	-
12.3(Ductility)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 7.2(Cut Angle)	-	50	-
Cl. 7.2(Length of Barbs)	-	50	-
Cl. 7.2(Finishing of Barbs)	-	50	-
Cl. 7.1(General)	-	50	-
4(Type A/Type B)	-	-	-
5 Table-1(Sizes Diameter of Line wire)	-	-	-
5 Table-1(Sizes Diamater of Point wire)	-	-	-
5 Table-1(Sizes Mass of Completed barbed wire)	-	-	-
5 Table-1(Sizes Distance between two barbs)	-	-	-
7.1(Manufacture)	-	-	-
7.2(Manufacture)	-	-	-
7.3(Manufacture)	-	-	-
8(CHROMATING)	-	-	-
9.1(Freedom from defects)	-	-	-
9.2(Freedom from defects)	-	-	-
12.1(Tensile Strength)	-	-	-
12.1(Breaking load)	-	-	-
12.2.1(Mass of zinc coating (line wire))	-	-	-
12.2.2(Mass of zinc coating (point wire))	-	-	-
12.2(Uniformity of zinc coating)	-	-	-
12.3(Ductility)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 6 . Table 1 of IS 7887 (Grade : 1,2,3,4,4M,6,6M,7,7M,8,8M,9,10,10M)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	-	-
Cl. 7.2(Cut Angle)	-	-	-
Cl. 7.2(Length of Barbs)	-	-	-
Cl. 7.2(Finishing of Barbs)	-	-	-
Cl. 7.1(General)	-	-	-

31 Dec, 2029

-
-

265

IS 1538 (1993)

Cast iron fittings for pressure pipes for water, gas and sewage - Specification (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(The metal used for the manufacture of pipe shall be of a quality not less than that specified for grade FG 150 of IS 210 )	-	500	-
5.1(tensile strength)	-	1500	-
6.1(Brinell hardness tests)	-	500	-
8(Hydrostatic Test)	-	950	-
9.1,Table 2 & 3(DI)	-	50	-
9.1,Table 2 & 3(P)	-	50	-
9.1,Table 2 & 3(g)	-	50	-
9.1,Table 2 & 3(h)	-	50	-
9.1,Table 2 & 3(K)	-	50	-
9.1,Table 2 & 3(L)	-	50	-
9.1,Table 2 & 3(M)	-	50	-
9.1,Table 2 & 3(N)	-	50	-
9.1,Table 2 & 3(f)	-	50	-
9.1,Table 4(D)	-	50	-
9.1,Table 4(a)	-	50	-
9.1,Table 4(b)	-	50	-
9.1,Table 4(s)	-	50	-
9.1,Table 4(r)	-	50	-
9.1,Table 5(D)	-	50	-
9.1,Table 5(g)	-	50	-
9.1,Table 5(a)	-	50	-
9.1,Table 5(b)	-	50	-
9.1,Table 5(c)	-	50	-
9.1,Table 5(f)	-	50	-
9.1,Table 5(s)	-	50	-
9.1,Table 5(C)	-	50	-
9.1,Table 5(Holes No)	-	50	-
9.1,Table 5(Holes diameter)	-	50	-
9.1,Table 5(Diameterof Bolts)	-	50	-
9.1,Table 6(D)	-	50	-
9.1,Table 6(C)	-	50	-
9.1,Table 6(Holes No)	-	50	-
9.1,Table 6(Holes diameter)	-	50	-
9.1,Table 6(Diameterof Bolts)	-	50	-
9.1&11.1,Table 7,8&9(e)	-	50	-
9.1&11.1,Table 7,8&9(l)	-	50	-
9.1&11.1,Table 7,8&9(Mass (Approx))	-	50	-
9.1&11.1,Table 10 to13(e)	-	50	-
9.1&11.1,Table 10 to13(r)	-	50	-
9.1&11.1,Table 10 to13(a)	-	50	-
9.1&11.1,Table 10 to13(b)	-	50	-
9.1&11.1,Table 10 to13(Mass (Approx))	-	50	-
9.1&11.1,Table 14(Nominal Diameter)	-	50	-
9.1&11.1,Table 14(e)	-	50	-
9.1&11.1,Table 14(e1)	-	50	-
9.1&11.1,Table 14(l)	-	50	-
9.1&11.1,Table 14(h)	-	50	-
9.1&11.1,Table 14(Mass (Approx))	-	50	-
9.1&11.1,Table 15(e)	-	50	-
9.1&11.1,Table 15(l)	-	50	-
9.1&11.1,Table 15(Nominal Diameter)	-	50	-
9.1&11.1,Table 15(e1)	-	50	-
9.1&11.1,Table 15(k)	-	50	-
9.1&11.1,Table 15(Mass (Approx))	-	50	-
9.1&11.1,Table 16(e)	-	50	-
9.1&11.1,Table 16(l)	-	50	-
9.1&11.1,Table 16(h)	-	50	-
9.1&11.1,Table 16(Mass (Approx))	-	50	-
9.1&11.1,Table 17(e1)	-	50	-
9.1&11.1,Table 17(l1)	-	50	-
9.1&11.1,Table 17(Nominal Diameter)	-	50	-
9.1&11.1,Table 17(e2)	-	50	-
9.1&11.1,Table 17(l2)	-	50	-
9.1&11.1,Table 17(l3)	-	50	-
9.1&11.1,Table 17(l)	-	50	-
9.1&11.1,Table 17(Mass)	-	50	-
9.1&11.1,Table 18(a)	-	50	-
9.1&11.1,Table 18(P)	-	50	-
9.1&11.1,Table 18(Mass (Approx))	-	50	-
9.1&11.1,Table 19(DC)	-	50	-
9.1&11.1,Table 19(e)	-	50	-
9.1&11.1,Table 19(a)	-	50	-
9.1&11.1,Table 19(l)	-	50	-
9.1&11.1,Table 19(Mass (Approx))	-	50	-
9.1&11.1,Table 20(DI)	-	50	-
9.1&11.1,Table 20(h)	-	50	-
9.1&11.1,Table 20(Mass (Approx))	-	50	-
9.1&11.1,Table 21(e)	-	50	-
9.1&11.1,Table 21(r)	-	50	-
9.1&11.1,Table 21(a)	-	50	-
9.1&11.1,Table 21(b)	-	50	-
9.1&11.1,Table 21(Mass (Approx))	-	50	-
9.1&11.1,Table 22(e)	-	50	-
9.1&11.1,Table 22(r)	-	50	-
9.1&11.1,Table 22(a)	-	50	-
9.1&11.1,Table 22(b)	-	50	-
9.1&11.1,Table 22(c)	-	50	-
9.1&11.1,Table 22(a)	-	50	-
9.1&11.1,Table 22(f)	-	50	-
9.1&11.1,Table 22(g)	-	50	-
9.1&11.1,Table 23(e)	-	50	-
9.1&11.1,Table 23(r)	-	50	-
9.1&11.1,Table 23(a)	-	50	-
9.1&11.1,Table 23(l)	-	50	-
9.1&11.1,Table 23(Mass (Approx))	-	50	-
9.1&11.1,Table 24(e)	-	50	-
9.1&11.1,Table 24(l)	-	50	-
9.1&11.1,Table 24(Nominal Diameter)	-	50	-
9.1&11.1,Table 24(e1)	-	50	-
9.1&11.1,Table 24(h)	-	50	-
9.1&11.1,Table 24(Mass (Approx))	-	50	-
9.1&11.1,Table 25(e)	-	50	-
9.1&11.1,Table 25(l)	-	50	-
9.1&11.1,Table 25(h)	-	50	-
9.1&11.1,Table 25(Mass (Approx))	-	50	-
9.1&11.1,Table 26(e1)	-	50	-
9.1&11.1,Table 26(h1)	-	50	-
9.1&11.1,Table 26(Nominal Diameter)	-	50	-
9.1&11.1,Table 26(e2)	-	50	-
9.1&11.1,Table 26(l2)	-	50	-
9.1&11.1,Table 26(l3)	-	50	-
9.1&11.1,Table 26(l)	-	50	-
9.1&11.1,Table 26(Mass (Approx))	-	50	-
9.1&11.1,Table 27(dn)	-	50	-
9.1&11.1,Table 27(e1)	-	50	-
9.1&11.1,Table 27(b)	-	50	-
9.1&11.1,Table 27(l3)	-	50	-
9.1&11.1,Table 27(l2)	-	50	-
9.1&11.1,Table 27(e2)	-	50	-
9.1&11.1,Table 27(r)	-	50	-
9.1&11.1,Table 27(a)	-	50	-
9.1&11.1,Table 27(l1)	-	50	-
9.1&11.1,Table 27(Mass)	-	50	-
9.1&11.1,Table 28(D)	-	50	-
9.1&11.1,Table 28(t)	-	50	-
9.1&11.1,Table 28(Mass (Approx))	-	50	-
12.1 to 12.7(Coating )	-	500	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

266

IS 1879 (2010)

Malleable cast iron pipe fittings - Specification (Third Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Type of Fittings - IS 1879)	-	200	BIS 10% discount
5.1.2(Size designation - IS 1879)	-	200	BIS 10% discount
5.1.2.1(Equal fitting - IS 1879)	-	200	BIS 10% discount
5.1.2.2(Unequal fitting -IS 1879)	-	200	BIS 10% discount
5.1.3(Right and Left hand thread - IS 1879)	-	200	BIS 10% discount
5.1.1(Code Number -IS 1879)	-	200	BIS 10% discount
6.1(Tensile Strength - IS 14329)	-	500	BIS 10% discount
6.1(Elongation - Is 14329)	-	500	BIS 10% discount
7.2- Table 2(Wall thickness of fittings - IS 1879)	-	200	BIS 10% discount
7.5 - Table 2(Projection of Rainforcement - IS 1879)	-	200	BIS 10% discount
7.5 - Table 3(Width of Rainforcement - IS 1879)	-	200	BIS 10% discount
7.1 - Table 4 to Table 27(a - IS 1879)	-	200	BIS 10% discount
7.1 - Table 28(d -IS 1879)	-	200	BIS 10% discount
8.1(Thread -IS 554)	-	1000	BIS 10% discount
8.2(Alignment of threads -IS 554)	-	1000	BIS 10% discount
9(Freedom from defects )	-	100	BIS 10% discount
10.i)(Mass of Galvanized coating)	-	500	BIS 10% discount
10.ii)(Uniformity of Galvanized coating-IS 2633)	-	500	BIS 10% discount
10.iii)(Adhesion of Galvanized coating IS 2629)	-	500	BIS 10% discount
10.iv)(Freedom from defects IS 4759)	-	100	BIS 10% discount
11(Pressure Test)	-	500	BIS 10% discount
8.1 (chem)(Thread -IS 554)	-	250	BIS 10% discount
5.1.1(Type of Fittings - IS 1879)	-	200	-
5.1.2(Size designation - IS 1879)	-	200	-
5.1.2.1(Equal fitting - IS 1879)	-	200	-
5.1.2.2(Unequal fitting -IS 1879)	-	200	-
5.1.3(Right and Left hand thread - IS 1879)	-	200	-
5.1.1(Code Number -IS 1879)	-	200	-
6.1(Tensile Strength - IS 14329)	-	500	-
6.1(Elongation - Is 14329)	-	500	-
7.2- Table 2(Wall thickness of fittings - IS 1879)	-	200	-
7.5 - Table 2(Projection of Rainforcement - IS 1879)	-	200	-
7.5 - Table 3(Width of Rainforcement - IS 1879)	-	200	-
7.1 - Table 4 to Table 27(a - IS 1879)	-	200	-
7.1 - Table 28(d -IS 1879)	-	200	-
8.1(Thread -IS 554)	-	1000	-
8.2(Alignment of threads -IS 554)	-	1000	-
9(Freedom from defects )	-	100	-
10.i)(Mass of Galvanized coating)	-	500	-
10.ii)(Uniformity of Galvanized coating-IS 2633)	-	500	-
10.iii)(Adhesion of Galvanized coating IS 2629)	-	500	-
10.iv)(Freedom from defects IS 4759)	-	100	-
11(Pressure Test)	-	500	-
8.1 (chem)(Thread -IS 554)	-	250	-
12(Compression Test)	-	250	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

267

IS 1825 (1983)

Specification for aluminium alloy milk cans (Second Revision)

7200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.1,3.2,3.3(Copper)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Manganese)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Silicon)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Iron)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Aluminium)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Magnesium)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Zinc)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Titanium)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Vanadium)	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Chromium)	-	100	BIS 10% discount
8(a) Rated Capacity)	-	300	BIS 10% discount
8(b) Point of Capacity)	-	300	BIS 10% discount
8(c) Batch OR Code No.)	-	100	BIS 10% discount
8(d) BIS Mark)	-	100	BIS 10% discount
8(e) Manufacturer's Trade Mark )	-	100	BIS 10% discount
2(Capacity)	-	300	BIS 10% discount
4 Fig. 1(Dimensions & Shape)	-	200	BIS 10% discount
4 Fig. 1(A)	-	100	BIS 10% discount
4 Fig. 1(B)	-	100	BIS 10% discount
4 Fig. 1(C )	-	100	BIS 10% discount
4 Fig. 1(D)	-	100	BIS 10% discount
4 Fig. 1(E)	-	100	BIS 10% discount
4 Fig. 1(F)	-	100	BIS 10% discount
4 Fig. 1(G)	-	100	BIS 10% discount
4 Fig. 1(H)	-	100	BIS 10% discount
4 Fig. 1(BOTTOM BAND)	-	100	BIS 10% discount
4 Fig. 1(Dimension)	-	200	BIS 10% discount
4 Fig. 1(HANDLE )	-	100	BIS 10% discount
4 Fig. 1(LID)	-	200	BIS 10% discount
4 Fig. 1(Hole Dia 8 ,2 holes)	-	100	BIS 10% discount
4 Fig. 1(Hole Dia 12, 3 holes)	-	100	BIS 10% discount
5(a)Transport cans shall consist of a body, bottom band)	-	100	BIS 10% discount
5(lid and handles.)	-	200	BIS 10% discount
5(b)Minimum Thickness(in mm))	-	100	BIS 10% discount
5(i) Body and Neck)	-	100	BIS 10% discount
5(ii) Bottom)	-	100	BIS 10% discount
5(iii) Lid (Inner))	-	100	BIS 10% discount
5(iv) Lid (Outer))	-	100	BIS 10% discount
5(c) Mode of Shaping)	-	100	BIS 10% discount
5(i) If the thickness at shoulder is less than 2.5 mm a )	-	100	BIS 10% discount
5(ii) Brinell Hardness 85 HB Min.)	-	100	BIS 10% discount
5(d) BOTTOM BAND- It shall be shrunk fit with a )	-	100	BIS 10% discount
5(proper locking arrangement on the body. This shall)	-	100	BIS 10% discount
5(be followed by brazing or welding all round.)	-	100	BIS 10% discount
5(e) HANDLES (as per Cl 5.6))	-	100	BIS 10% discount
5(f) SEALING LUG (as per Cl 5.7))	-	100	BIS 10% discount
5(g)Workmanship and Finish- All brazing or welding shall )	-	100	BIS 10% discount
5(be sound , free of porosity and shall be finished smooth .)	-	100	BIS 10% discount
5(h) Mass 6.5 Kg. Min.)	-	100	BIS 10% discount
7(i) Air Pressure Test (Cl 7.1))	-	300	BIS 10% discount
7(ii) Drop Test (Cl 7.2))	-	300	BIS 10% discount
7(iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-	400	BIS 10% discount
8(a) Rated Capacity)	-	300	BIS 10% discount
8(b) Point of Capacity)	-	300	BIS 10% discount
8(c) Batch OR Code No.)	-	100	BIS 10% discount
8(d) BIS Mark)	-	100	BIS 10% discount
8(e) Manufacturer's Trade Mark )	-	100	BIS 10% discount
Cl. 3.1,3.2,3.3(Copper)	-	100	-
Cl. 3.1,3.2,3.3(Manganese)	-	100	-
Cl. 3.1,3.2,3.3(Silicon)	-	100	-
Cl. 3.1,3.2,3.3(Iron)	-	100	-
Cl. 3.1,3.2,3.3(Aluminium)	-	100	-
Cl. 3.1,3.2,3.3(Magnesium)	-	100	-
Cl. 3.1,3.2,3.3(Zinc)	-	100	-
Cl. 3.1,3.2,3.3(Titanium)	-	100	-
Cl. 3.1,3.2,3.3(Vanadium)	-	100	-
Cl. 3.1,3.2,3.3(Chromium)	-	100	-
8(a) Rated Capacity)	-	300	-
8(b) Point of Capacity)	-	300	-
8(c) Batch OR Code No.)	-	100	-
8(d) BIS Mark)	-	100	-
8(e) Manufacturer's Trade Mark )	-	100	-
2(Capacity)	-	300	-
4 Fig. 1(Dimensions & Shape)	-	200	-
4 Fig. 1(A)	-	100	-
4 Fig. 1(B)	-	100	-
4 Fig. 1(C )	-	100	-
4 Fig. 1(D)	-	100	-
4 Fig. 1(E)	-	100	-
4 Fig. 1(F)	-	100	-
4 Fig. 1(G)	-	100	-
4 Fig. 1(H)	-	100	-
4 Fig. 1(BOTTOM BAND)	-	100	-
4 Fig. 1(Dimension)	-	200	-
4 Fig. 1(HANDLE )	-	100	-
4 Fig. 1(LID)	-	100	-
4 Fig. 1(Hole Dia 8 ,2 holes)	-	100	-
4 Fig. 1(Hole Dia 12, 3 holes)	-	100	-
5(a)Transport cans shall consist of a body, bottom band)	-	100	-
5(lid and handles.)	-	100	-
5(b)Minimum Thickness(in mm))	-	100	-
5(i) Body and Neck)	-	100	-
5(ii) Bottom)	-	100	-
5(iii) Lid (Inner))	-	100	-
5(iv) Lid (Outer))	-	100	-
5(c) Mode of Shaping)	-	100	-
5(i) If the thickness at shoulder is less than 2.5 mm a )	-	100	-
5(ii) Brinell Hardness 85 HB Min.)	-	100	-
5(d) BOTTOM BAND- It shall be shrunk fit with a )	-	100	-
5(proper locking arrangement on the body. This shall)	-	100	-
5(be followed by brazing or welding all round.)	-	100	-
5(e) HANDLES (as per Cl 5.6))	-	100	-
5(f) SEALING LUG (as per Cl 5.7))	-	100	-
5(g)Workmanship and Finish- All brazing or welding shall )	-	100	-
5(be sound , free of porosity and shall be finished smooth .)	-	100	-
5(h) Mass 6.5 Kg. Min.)	-	100	-
7(i) Air Pressure Test (Cl 7.1))	-	300	-
7(ii) Drop Test (Cl 7.2))	-	300	-
7(iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-	100	-
8(a) Rated Capacity)	-	300	-
8(b) Point of Capacity)	-	300	-
8(c) Batch OR Code No.)	-	100	-
8(d) BIS Mark)	-	100	-
8(e) Manufacturer's Trade Mark )	-	100	-
Cl. 3.1,3.2,3.3(Copper)	-	100	-
Cl. 3.1,3.2,3.3(Manganese)	-	100	-
Cl. 3.1,3.2,3.3(Silicon)	-	100	-
Cl. 3.1,3.2,3.3(Iron)	-	100	-
Cl. 3.1,3.2,3.3(Aluminium)	-	100	-
Cl. 3.1,3.2,3.3(Magnesium)	-	100	-
Cl. 3.1,3.2,3.3(Zinc)	-	100	-
Cl. 3.1,3.2,3.3(Titanium)	-	100	-
Cl. 3.1,3.2,3.3(Vanadium)	-	100	-
Cl. 3.1,3.2,3.3(Chromium)	-	100	-
8(a) Rated Capacity)	-	300	-
8(b) Point of Capacity)	-	300	-
8(c) Batch OR Code No.)	-	100	-
8(d) BIS Mark)	-	100	-
8(e) Manufacturer's Trade Mark )	-	100	-
2(Capacity)	-	300	-
4 Fig. 1(Dimensions & Shape)	-	200	-
4 Fig. 1(A)	-	100	-
4 Fig. 1(B)	-	100	-
4 Fig. 1(C )	-	100	-
4 Fig. 1(D)	-	100	-
4 Fig. 1(E)	-	100	-
4 Fig. 1(F)	-	100	-
4 Fig. 1(G)	-	100	-
4 Fig. 1(H)	-	100	-
4 Fig. 1(BOTTOM BAND)	-	100	-
4 Fig. 1(Dimension)	-	200	-
4 Fig. 1(HANDLE )	-	100	-
4 Fig. 1(LID)	-	100	-
4 Fig. 1(Hole Dia 8 ,2 holes)	-	100	-
4 Fig. 1(Hole Dia 12, 3 holes)	-	100	-
5(a)Transport cans shall consist of a body, bottom band)	-	100	-
5(lid and handles.)	-	100	-
5(b)Minimum Thickness(in mm))	-	100	-
5(i) Body and Neck)	-	100	-
5(ii) Bottom)	-	100	-
5(iii) Lid (Inner))	-	100	-
5(iv) Lid (Outer))	-	100	-
5(c) Mode of Shaping)	-	100	-
5(i) If the thickness at shoulder is less than 2.5 mm a )	-	100	-
5(ii) Brinell Hardness 85 HB Min.)	-	100	-
5(d) BOTTOM BAND- It shall be shrunk fit with a )	-	100	-
5(proper locking arrangement on the body. This shall)	-	100	-
5(be followed by brazing or welding all round.)	-	100	-
5(e) HANDLES (as per Cl 5.6))	-	100	-
5(f) SEALING LUG (as per Cl 5.7))	-	100	-
5(g)Workmanship and Finish- All brazing or welding shall )	-	100	-
5(be sound , free of porosity and shall be finished smooth .)	-	100	-
5(h) Mass 6.5 Kg. Min.)	-	100	-
7(i) Air Pressure Test (Cl 7.1))	-	300	-
7(ii) Drop Test (Cl 7.2))	-	300	-
7(iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-	100	-
8(a) Rated Capacity)	-	300	-
8(b) Point of Capacity)	-	300	-
8(c) Batch OR Code No.)	-	100	-
8(d) BIS Mark)	-	100	-
8(e) Manufacturer's Trade Mark )	-	100	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

268

IS 2039 : Part 1 to 3 (1991)

Steel tubes for bicycle and cycle rickshaws - Specification (Second Revision)

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1 Table 1(Carbon)	-	100	BIS 10% discount
Cl. 5.1 Table 1(Silicon)	-	100	BIS 10% discount
Cl. 5.1 Table 1(Manganese)	-	100	BIS 10% discount
Cl. 5.1 Table 1(Phosphorous)	-	100	BIS 10% discount
Cl. 5.1 Table 1(Sulphur)	-	100	BIS 10% discount
Cl. 6.1(Workmanship)	-	200	BIS 10% discount
Cl. 6.2(Fin Height)	-	2000	BIS 10% discount
Cl. 6.3(Straightness)	-	2000	BIS 10% discount
Cl. 8.1(Tensile Strength)	-	1000	BIS 10% discount
Cl. 8.1(Yield Strength)	-	1000	BIS 10% discount
Cl. 8.1(Elongation)	-	500	BIS 10% discount
Cl. 8.2(Drift Expansion Test- IS 2335)	-	1500	BIS 10% discount
Cl. 8.3(Flattening Test-IS 2338)	-	1500	BIS 10% discount
Cl. 4.2.1(Diameter)	-	600	BIS 10% discount
Cl. 4.2.2(Thickness)	-	500	BIS 10% discount
Cl. 3.2.1, Table 4(Yield Stress)	-	500	BIS 10% discount
Cl. 3.2.1, Table 4(UTS)	-	1000	BIS 10% discount
Cl. 3.2.1, Table 4(Elongation)	-	500	BIS 10% discount
Cl. 3.2.2, Table 2(Drift Expansion Test- IS 2335)	-	1500	BIS 10% discount
Cl. 3.2.3, Table 3(Flattening Test-IS 2338)	-	1500	BIS 10% discount
Cl. 4.2.3(Length)	-	500	BIS 10% discount
Cl. 3.1(Carbon)	-	100	BIS 10% discount
Cl. 3.1(Silicon)	-	100	BIS 10% discount
Cl. 3.1(Manganese)	-	100	BIS 10% discount
Cl. 3.1(Phosphorous)	-	100	BIS 10% discount
Cl. 3.1(Sulphur)	-	100	BIS 10% discount
Cl. 4.2.1, Table 7(Yield Stress)	-	1000	BIS 10% discount
Cl. 4.2.1, Table 7(UTS)	-	1000	BIS 10% discount
Cl. 4.2.1, Table 7(Crushing)	-	600	BIS 10% discount
Cl. 4.2.2, Table 8(Drift Expansion Test- IS 2335)	-	1000	BIS 10% discount
Cl. 4.2.3, Table 9(Flattening Test-IS 2338)	-	1500	BIS 10% discount
Cl. 9(Diameter)	-	600	BIS 10% discount
Cl. 5.2.2(Mean Thickness)	-	500	BIS 10% discount
Cl. 5.2.3, Table 6(Length)	-	500	BIS 10% discount

31 Dec, 2029

-
Included w.e.f. 07.11.2023

269

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

11250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Tensile Test & Flattening Test)	-	2250	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	3500	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	1500	-
Cl 10(Outer Diameter & Overall Length)	-	700	-
Cl 12(Bituminous Coating & Galvanizing )	-	2000	-
Cl 14(Workmanship)	-	350	-
5.2(phosphorus)	-	300	-
Cl 14(Workmanship)	-	350	-
5.2(sulphur)	-	300	-
Cl 6(Tensile Test & Flattening Test)	-	2250	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	3500	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	1500	-
Cl 10(Outer Diameter & Overall Length)	-	700	-
Cl 12(Bituminous Coating & Galvanizing )	-	2000	-
Cl 14(Workmanship)	-	350	-
Cl 6(Tensile Test & Flattening Test)	-	2250	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	3500	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	1500	-
Cl 10(Outer Diameter & Overall Length)	-	700	-
Cl 12(Bituminous Coating & Galvanizing )	-	2000	-
Cl 14(Workmanship)	-	350	-
11.0(Alignment test IS 4270: 2001)	-	350	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

270

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1 Table 2 Table 3(Carbon Content IS 228)	-	100	-
8.1 Table 2 Table 3(Manganese Content IS 228)	-	100	-
8.1 Table 2 Table 3(Phosphorus Content IS 228)	-	100	-
8.1 Table 2 Table 3(Sulphur Content IS 228)	-	100	-
9.3(Guided bend test(For SAW Pipes))	-	500	-
10(Hydaulic pressure test)	-	1000	-
11.1, Table 5.(Outside Diameter (OD))	-	500	-
11.1, Table 5.(Thickness)	-	200	-
11.1, Table 5.(Mass)	-	200	-
12.3.3(Ovality)	-	200	-
12.5(Strightness)	-	1000	-
14.1(Visual inspection, Appearance and Workmanship)	-	200	-
14.4(Visual inspection, Appearance and Workmanship-Dent Depth(below 610 mm OD))	-	200	-
14.4(Visual inspection, Appearance and Workmanship-Dent Length)	-	200	-
8.1(CE)	-	500	-
9.3(Guided Bend Test (for SAW Pipes))	-	500	-
9.2.3(Flattening Test for seamless pipes)	-	500	-
9.2.1(Flattening test for ERW pipes )	-	500	-
9.1(Tensile test-Yield Strength)	-	1400	-
9.1(Tensile test-Strength)	-	1000	-
9.1(Tensile test- Elongation)	-	1000	-
8.1 Table 2 Table 3(Carbon Content IS 228)	-	100	-
8.1 Table 2 Table 3(Manganese Content IS 228)	-	100	-
8.1 Table 2 Table 3(Phosphorus Content IS 228)	-	100	-
8.1 Table 2 Table 3(Sulphur Content IS 228)	-	100	-
9.3(Guided bend test(For SAW Pipes))	-	500	-
10(Hydaulic pressure test)	-	1000	-
11.1, Table 5.(Outside Diameter (OD))	-	500	-
11.1, Table 5.(Thickness)	-	200	-
11.1, Table 5.(Mass)	-	200	-
12.3.3(Ovality)	-	200	-
12.5(Strightness)	-	1000	-
14.1(Visual inspection, Appearance and Workmanship)	-	200	-
14.4(Visual inspection, Appearance and Workmanship-Dent Depth(below 610 mm OD))	-	200	-
14.4(Visual inspection, Appearance and Workmanship-Dent Length)	-	200	-
8.1(CE)	-	500	-
8.1 Table 2 Table 3(Carbon Content IS 228)	-	-	-
8.1 Table 2 Table 3(Manganese Content IS 228)	-	-	-
8.1 Table 2 Table 3(Phosphorus Content IS 228)	-	-	-
8.1 Table 2 Table 3(Sulphur Content IS 228)	-	-	-
9.3(Guided bend test(For SAW Pipes))	-	-	-
10(Hydaulic pressure test)	-	-	-
11.1, Table 5.(Outside Diameter (OD))	-	-	-
11.1, Table 5.(Thickness)	-	-	-
11.1, Table 5.(Mass)	-	-	-
12.3.3(Ovality)	-	-	-
12.5(Strightness)	-	-	-
14.1(Visual inspection, Appearance and Workmanship)	-	-	-
14.4(Visual inspection, Appearance and Workmanship-Dent Depth(below 610 mm OD))	-	-	-
14.4(Visual inspection, Appearance and Workmanship-Dent Length)	-	-	-
8.1(CE)	-	-	-

31 Dec, 2029

-
Included w.e.f. 07.11.2023

Bureau of Indian Standards

The National Standards Body of India

Alpha Test House Services LLP (160), Sahibzada Ajit Singh Nagar

plot no.160,Industrial Area Phase-9, Sahibzada Ajit Singh Nagar, S.A.S Nagar, Punjab, 160062

9888717272 chandigarh@alphatesthouse.com

Scope List