BIS - LIMS (Laboratory Information Management System)

UL INDIA PRIVATE LIMITED

Loc 1&2-Kalyani Platina Campus, Sy. no 129/4, EPIP Zone, Phase II, Whitefield, Bangalore- 560066, Loc3- 30/A, I Stage Vishveshwarya Industrial Estate, Doddanekkundi Industrial Area, Bangalore - 560048, Bangalore, Bengaluru Urban, Karnataka, 560066

9986066622 sarangan.nandakumar@ul.com

Scope List

Reset

34 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 16046 : Part 2 (2018)

Secondary Cells and Batteries Containing Alkaline or Other Non-Acid Electrolytes ” Safety Requirements for Portable Sealed Secondary Cells and for Batteries Made from Them for Use in Portable Applications Part 2 Lithium Systems ( Second Revision )

300000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Insulation and Wiring)	-	15000	-
7.1(Charging procedure for test purposes)	-	35000	-
5.1(General)	-	0	-
5.3(Venting)	-	0	-
7.2(Intended Use)	-	35000	-
7.3(Reasonably foreseeable misuse)	-	215000	-
5.4(Temperature, Voltage and Current Management)	-	0	-
5.5(Terminal Contacts)	-	0	-
9(Marking)	-	0	-
9.1(Cell Marking)	-	0	-
9.2(Battery Marking)	-	0	-
9.3(Caution for ingestion of small cells and batteries)	-	0	-

12 May, 2027

-
-

IS 14286 : Part 1 : Sec 4 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-4: Special requirements for testing of thin-film CuInGASSe2 based photovoltaic PV modules Third Revision

PHOTOVOLTAIC (PV) MODULE

2384500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	30000	-
Cl-11.1(Visual inspection (MQT 01))	-	30000	-
Cl-11.2(Maximum power determination (MQT 02))	-	26000	-
Cl-11.3(Insulation test (MQT 03))	-	70000	-
Cl-11.4(Measurement of temperature coefficients (MQT 04))	-	100000	-
Cl-11.5(Measurement of nominal module operating temperature (NMOT) (MQT 05))	-	0	-
Cl-11.6(Performance at STC (MQT 06.1) and NMOT (MQT 06.2)	-	42000	-
Cl-11.7(Performance at low irradiance (MQT 07))	-	19500	-
Cl-11.8(Outdoor exposure test (MQT 08))	-	80000	-
Cl-11.9(Hot-spot endurance test (MQT 09))	-	25000	-
Cl-11.10(UV preconditioning test (MQT 10))	-	120000	-
Cl-11.11(Thermal cycling test (MQT 11))	-	400000	-
Cl-11.12(As per IEC 61215-1:2016)	-	250000	-
Cl-11.13(Damp heat test (MQT 13))	-	400000	-
Cl-11.14(Robustness of terminations test (MQT 14))	-	12000	-
Cl-11.15(Robustness of terminations test (MQT 14))	-	65000	-
Cl-11.16(Static mechanical load test (MQT 16))	-	20000	-
Cl-11.17(Hail test (MQT 17))	-	20000	-
Cl-11.18(Bypass diode testing (MQT 18))	-	20000	-
Cl-11.19(Stabilization (MQT 19))	-	150000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	80000	-
11.21(Potential induced degradation test (MQT 21))	-	350000	-
11.22(Bending test (MQT 22))	-	70000	-
5(Marking and documentation)	-	5000	-

12 May, 2027

-
Included w.e.f.09.04.2025

IS 14286 : Part 1 : Sec 3 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-3: Special requirements for testing of thin-film amorphous silicon based photovoltaic PV modules Third Revision

PHOTOVOLTAIC (PV) MODULE

2384500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	30000	-
Cl-11.1(Visual inspection)	-	30000	-
Cl-11.2(Maximum power determination)	-	26000	-
Cl-11.3(Insulation test)	-	70000	-
Cl-11.4(Measurement of temperature coefficients)	-	100000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC and NMOT)	-	42000	-
Cl-11.7(Performance at low irradiance)	-	19500	-
Cl-11.8(Outdoor exposure test)	-	80000	-
Cl-11.9(Hot-spot endurance test)	-	25000	-
Cl-11.10(UV preconditioning test)	-	120000	-
Cl-11.11(Thermal cycling test)	-	400000	-
Cl-11.12(Humidity-freeze test)	-	250000	-
Cl-11.13(Damp heat test)	-	400000	-
Cl-11.14(Robustness of terminations test)	-	12000	-
Cl-11.15(Wet leakage current test)	-	65000	-
Cl-11.16(Static mechanical load test)	-	20000	-
Cl-11.17(Hail test)	-	20000	-
Cl-11.18(Bypass diode testing)	-	20000	-
Cl-11.19(Stabilization)	-	150000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	80000	-
11.21(Potential induced degradation test (MQT 21))	-	350000	-
11.22(Bending test (MQT 22))	-	70000	-
5(Marking and documentation)	-	5000	-

12 May, 2027

-
Included w.e.f.09.04.2025

IS 14286 : Part 1 : Sec 2 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-2: Special requirements for testing of thin-film Cadmium Telluride CdTe based photovoltaic PV modules Third Revision

PHOTOVOLTAIC (PV) MODULE

2384500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	30000	-
Cl-11.1(Visual inspection)	-	30000	-
Cl-11.2(Maximum power determination)	-	26000	-
Cl-11.3(Insulation tes)	-	70000	-
Cl-11.4(Measurement of temperature coefficients)	-	100000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC and NMOT)	-	42000	-
Cl-11.7(Performance at low irradiance)	-	19500	-
Cl-11.8(Outdoor exposure test)	-	80000	-
Cl-11.9(Hot-spot endurance test)	-	25000	-
Cl-11.10(UV preconditioning test)	-	120000	-
Cl-11.11(Thermal cycling test)	-	400000	-
Cl-11.12(Humidity-freeze test)	-	250000	-
Cl-11.13(Damp heat test)	-	400000	-
Cl-11.14(Robustness of terminations test)	-	12000	-
Cl-11.15(Wet leakage current test)	-	65000	-
Cl-11.16(Static mechanical load test)	-	20000	-
Cl-11.17(Hail test)	-	20000	-
Cl-11.18(Bypass diode testing)	-	20000	-
Cl-11.19(Stabilization)	-	150000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	80000	-
11.21(Potential induced degradation test (MQT 21))	-	350000	-
11.22(Bending test (MQT 22))	-	70000	-
5(Marking and documentation)	-	5000	-

12 May, 2027

-
Included w.e.f.09.04.2025

IS 14286 : Part 1 : Sec 1 (2023)

Terrestrial photovoltaic PV modules Design qualification and type approval Part 1-1: Special requirements for testing of crystalline silicon photovoltaic PV modules Third Revision

PHOTOVOLTAIC (PV) MODULE

2384500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-8(Major visual defects)	-	30000	-
Cl-11.1(Visual inspection)	-	30000	-
Cl-11.2(Maximum power determination)	-	26000	-
Cl-11.3(Insulation test)	-	70000	-
Cl-11.4(Measurement of temperature coefficients)	-	100000	-
Cl-11.5(Measurement of nominal module operating temperature)	-	0	-
Cl-11.6(Performance at STC)	-	42000	-
Cl-11.7(Performance at low irradiance)	-	19500	-
Cl-11.8(Outdoor exposure test)	-	80000	-
Cl-11.9(Hot-spot endurance test)	-	25000	-
Cl-11.10(UV preconditioning test)	-	120000	-
Cl-11.11(Thermal cycling test)	-	400000	-
Cl-11.12(Humidity-freeze test)	-	250000	-
Cl-11.13(Damp heat test)	-	400000	-
Cl-11.14(Robustness of terminations test)	-	12000	-
Cl-11.15(Wet leakage current tes)	-	65000	-
Cl-11.16(Static mechanical load test)	-	20000	-
Cl-11.17(Hail test)	-	20000	-
Cl-11.18(Bypass diode thermal test)	-	20000	-
Cl-11.19(Stabilization)	-	150000	-
11.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	80000	-
11.21(Potential induced degradation test (MQT 21))	-	350000	-
11.22(Bending test (MQT 22))	-	70000	-
5(Marking and documentation)	-	5000	-

12 May, 2027

-
Included w.e.f.09.04.2025

IS 14286 : Part 1 (2023)

Terrestrial Photovoltaic PV Modules Design Qualification and Type Approval Part 1: Test Requirements (Third Revision)

PHOTOVOLTAIC (PV) MODULE

2349500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Visual inspection (MQT 01))	-	30000	-
4.2(Maximum power determination (MQT 02))	-	26000	-
4.3(Insulation test (MQT 03))	-	70000	-
4.4(Measurement of temperature coefficients (MQT 04))	-	100000	-
4.6(Performance at STC (MQT 06.1))	-	42000	-
4.7(Performance at low irradiance (MQT 07))	-	19500	-
4.8(Outdoor exposure test (MQT 08))	-	80000	-
4.9(Hot-spot endurance test (MQT 09))	-	25000	-
4.10(UV preconditioning test (MQT 10))	-	120000	-
4.11(Thermal cycling test (MQT 11))	-	400000	-
4.12(2 Humidity-freeze test (MQT 12))	-	250000	-
4.13(Damp heat test (MQT 13))	-	400000	-
4.14(Robustness of terminations (MQT 14))	-	12000	-
4.15(5 Wet leakage current test (MQT 15))	-	65000	-
4.16(Static mechanical load test (MQT 16))	-	20000	-
4.17(Hail test (MQT 17))	-	20000	-
4.18(Bypass diode testing (MQT 18))	-	20000	-
4.19(Stabilization (MQT 19))	-	150000	-
4.20(Cyclic (dynamic) mechanical load test (MQT 20))	-	80000	-
4.21(Potential induced degradation test (MQT 21))	-	350000	-
4.22(Bending test (MQT 22))	-	70000	-
4.5(Placeholder section, formerly NMOT)	-	0	-

12 May, 2027

-
Included w.e.f.09.04.2025

IS/IEC 60947 : Part 4 : Sec 1 (2018)

Low-Voltage switchgear and controlgear : Part 4-1 Contactors and motor starters electromechanical contactors and motor-Starters

Low voltage switchgear and control gear - Contactors and Motor Starters

2064566 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.2(Materials)	-	0	-
8.1.2.1(General materials requirements)	-	0	-
8.1.2.2(Glow wire testing)	-	20000	Test Charges will vary depending on the rating, tripping class, DC rating of the sample Test charge applicable will be intimated through a proforma invoice + taxes
8.1.2.3(Test based on flammability category)	-	0	No feasibility
8.1.3(Current-carrying parts and their connections)	-	0	-
8.1.4(Clearances and creepage distances)	-	10000	-
8.1.5.1(Insulation)	-	0	-
8.1.5.2(Direction of movement)	-	0	-
8.1.5.3(Mounting)	-	0	-
8.1.5.4(Protection)	-	0	-
8.1.8(Terminals)	-	0	-
8.1.8.1(General)	-	0	-
8.1.8.2(Terminal identification and marking)	-	0	-
8.1.9(Additional requirements for equipment provided with a neutral pole)	-	0	-
8.1.10(Provisions for protective earthing)	-	0	-
8.1.11(Enclosures for equipment)	-	0	-
8.1.11.1(Design)	-	0	-
8.1.11.2(Insulation)	-	0	-
8.1.12(Degrees of protection of enclosed equipment)	-	40000	-
8.1.13(Conduit pull-out, torque and bending with metallic conduits)	-	30000	-
8.1.14(Limited energy source)	-	10000	-
8.1.14.1(General)	-	0	-
8.1.14.2(Limited energy source with galvanic separation)	-	20000	-
8.1.14.3(Limited energy source with current limiting impedance)	-	20000	-
8.1.15(Stored charge energy circuit)	-	0	-
8.1.16(Fault and abnormal conditions)	-	20000	-
8.1.17(Short-circuit and overload protection of ports)	-	25000	-
8.2(Performance requirements)	-	0	-
8.2.1.1.1(General conditions)	-	0	-
8.2.1.2(Limits of operation of contactors and power-operated starters)	-	20000	-
8.2.1.3(Limits of operation of under-voltage relays and releases)	-	20000	-
8.2.1(Operating conditions)	-	0	-
8.2.1.4(Limits of operation of shunt-coil operated releases (shunt trip))	-	20000	-
8.2.1.5.1.1(General tripping requirements of overload relays)	-	0	-
8.2.1.5.1(Limits of operation of time-delay overload relays when all poles are energized)	-	35000	-
8.2.1.5(Limits of operation of current sensing relays and releases)	-	35000	-
8.2.1.5.1.2(Thermal memory test verification)	-	25000	-
8.2.1.5.2(Limits of operation of three-pole time-delay overload relays energized on two poles)	-	35000	-
8.2.1.5.3(Limits of operation of instantaneous magnetic overload relays)	-	35000	-
8.2.1.5.4(Limits of operation of under-current relays and releases for automatic change over)	-	35000	-
8.2.1.5.4.1(Limits of operation of under-current relays)	-	35000	-
8.2.1.5.4.2(Limits of operation of automatic change over by under-current relays)	-	35000	-
8.2.2(Temperature-rise)	-	40000	-
8.2.2.3(Accessible parts)	-	0	-
8.2.2.4(Ambient air temperature)	-	0	-
8.2.2.5(Main circuit)	-	0	-
8.2.2.6(Control circuits)	-	0	-
8.2.2.7.1(Uninterrupted and eight-hour duty windings)	-	20000	-
8.2.3(Dielectric properties)	-	25000	-
8.2.3.2(Voltage limiting components between circuits)	-	0	-
8.2.4.3.1(Mechanical durability)	-	96000	-
8.2.4.3.2(Electrical durability)	-	144000	-
8.2.4.4(Overload current withstand capability of contactors)	-	25000	-
8.2.4.5(Coil power consumption)	-	25000	-
8.2.4.6(Pole impedance)	-	10000	-
8.2.4.7(Ability of a MPSD to make and break under short-circuit conditions)	-	60000	-
8.2.5.1(Performance under short-circuit conditions)	-	60000	-
8.2.5.3(Co-ordination test between AC-3e rated starter and associated SCPD)	-	60000	-
8.2.5.4(Co-ordination between a MPSD and another short-circuit protective device)	-	60000	-
8.3(Electromagnetic compatibility (EMC))	-	400000	-
8.3.2(Immunity)	-	320000	-
8.3.3(Emission)	-	80000	-
9.1.5.2(Environment tests)	-	280000	-
9.2.2(Electrical performance of screwless-type clamping units)	-	10000	-
9.2.3(Ageing test for screwless-type clamping unit)	-	25000	-
9.2.4(Limited energy source test)	-	20000	-
9.2.5(Breakdown of components)	-	20000	-
9.2.5.2(Breakdown of components test)	-	20000	-
9.3.3.2(Operating limits)	-	80000	-
9.3.3.2.1.2(Coil power consumption)	-	40000	-
9.3.3.2.1.3(Pole impedance)	-	10000	-
9.3.3.2.2(Relays and releases)	-	90000	-
9.3.3.3.1(Ambient air temperature)	-	0	-
9.3.3.3.2(Measurement of the temperature of parts)	-	0	-
9.3.3.3.3(Temperature-rise of a part)	-	0	-
9.3.3.3.4(Temperature-rise of the main circuit)	-	40000	-
9.3.3.3.5(Temperature-rise of control circuits)	-	30000	-
9.3.3.3.6(Temperature-rise of coils and electromagnets)	-	20000	-
9.3.3.3.7(Temperature-rise of auxiliary circuits)	-	20000	-
9.3.3.3.8(Temperature-rise of starting resistors for rheostatic rotor starters)	-	35000	-
9.3.3.6(Operational performance capability)	-	90000	-
9.3.4.2.2(prospective current)	-	0	-
9.3.4.2.3(Test at the rated conditional short-circuit current Iq)	-	60000	-
9.3.5(Overload current withstand capability of contactors)	-	45000	-
9.3.6.2(Operation and operating limits)	-	80000	-
9.3.6.3(Dielectric tests)	-	10000	-
9.3.6.4(Mechanical operation tests of a MPSD)	-	45000	-
9.4.2(Immunity)	-	320000	-
9.4.2.2(Electrostatic discharge)	-	30000	-
9.4.2.3(Radiated radio-frequency electromagnetic field)	-	120000	-
9.4.2.4(Conducted disturbances induced by radio-frequency fields)	-	30000	-
9.4.2.5(Electrical fast transient/bursts)	-	30000	-
9.4.2.6(Surges)	-	50000	-
9.4.2.7(Power frequency magnetic field)	-	30000	-
9.4.2.8(Voltage dips and short-time interruptions)	-	30000	-
9.4.2.9(Harmonics in the supply)	-	0	-
9.4.3(Emission)	-	80000	-
F.7.2(Tests on products in a new condition)	-	20000	-
F.7.3(Test after conventional operational performance)	-	90000.02	-
H.3(Limits of operation of control functions)	-	40000	-
H.4(Test of the control functions)	-	40000	-
M.8.3(Electromagnetic compatibility (EMC))	-	400000	-
M.9.4(Thermal cycling test)	-	120000	-
M.9.5(Climatic test)	-	180000	-
M.9.7(Critical load current test)	-	20000	-
8.2.4 of IEC 60947-1:2007 (Sequence 5)(Verification of Mechanical properties of terminals)	-	30000	-
Annex C of IEC 60947-1:2007 (Sequence 5)(Verification of Degree of protection of enclosed contactors and starters)	-	40000	-
M.9.11(Clearance and creepage distances)	-	10000	-
N.3.2(Touch current measurement)	-	15000	-
P.2.3(Verification of operational performance capability)	-	90000	-
P.2.4.2(Test voltage)	-	10000	-
P.2.4.3(Application of the test voltage)	-	0	-
P.4(Test of MPSD for IT system)	-	95000	-
Q.5.3(Selectivity determined by test)	-	95000	-

12 May, 2027

-
Exclusions: 8.1.2.3 (Test based on flammability category), 8.1.12 (Degrees of protection of enclosed equipment), 9.4.2.9 (Harmonics in the supply), M.9.9 (Degree of protection of enclosed contactors)

IS/IEC 60947 : Part 5 : Sec 1 (2016)

Low-Voltage Switchgear And Control Gear : Part 5-1 Control Circuit Devices And Switching Elements Electromechanical Control Circuit Devices

Control Circuit Devices And Switching Elements Electromechanical Control Circuit Devices

2061000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1(Marking : General ")	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.2.2(Terminal identification and marking)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.2.3(Functional markings)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.2.4(Emergency stop)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.2.5(Operating diagram)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.2.5.1(Position indication)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.2.5.2(Terminal markings for operating diagrams)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.2.6(Time delay markings)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
5.3(Instructions for installation, operation and maintenance)	-	500	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.1.2.2(Glow-wire testing)	-	10000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.1.3(Current-carrying parts and their connections)	-	35000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.1.4(Clearances and creepage distances)	-	25000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.2.4.1(Making and breaking capacities)	-	80000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.2.4.3(Durability)	-	240000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.3.2.4(Electrostatic discharges)	-	30000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.3.2.5(Radiated radio-frequency electromagnetic fields)	-	120000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.3.2.6(Electrical fast transients/bursts)	-	30000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.3.2.7(Surges)	-	50000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.3.2.8(Conducted disturbances induced by radio-frequency fields)	-	30000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.3.2.9(Power-frequency magnetic fields)	-	30000	375000(For sequence testings of 1 sample); 1226000(For Annex & Other testings of 1 sample); 460000 (For EMC tests per sample) Total cost 2061000 (Seq. tests + Annex tests + EMC tests)
7.3.2.10(Voltage dips and interruptions)	-	30000	-
7.3.3(Emission)	-	30000	-
7.2.3(Dielectric properties)	-	15000	-
8.1.5(Special tests)	-	350000	-
8.2.1.1(Test of resistance to abnormal heat and fire)	-	25000	-
8.2.1.1.1(Glow-wire test)	-	15000	-
8.2.1.1.2(Flammability, hot wire ignition and arc ignition tests (on materials))	-	15000	-
8.2.3(Enclosures for equipment)	-	60000	-
8.2.4(Mechanical and electrical properties of terminals)	-	25000	-
8.2.4.2(Tests of mechanical strength of terminals)	-	25000	-
8.2.4.3(Testing for damage to and accidental loosening of conductors (flexion test))	-	25000	-
8.2.4.4(Pull-out test)	-	10000	-
8.2.4.5(Test for insertability of unprepared round copper conductors having the maximum cross-section)	-	5000	-
8.2.5(Verification of actuating force (or moment))	-	5000	-
8.2.6(Verification of limitation of rotation (of a rotary switch))	-	5000	-
8.2.7(Conduit pull-out test, torque test, and bending test with metallic conduits)	-	20000	-
8.3.3.3(Temperature rise)	-	25000	-
8.3.3.4(Dielectric properties)	-	15000	-
8.3.3.2(Operating limits of contactor relays)	-	15000	-
8.3.3.5(Making and breaking capacities)	-	80000	-
8.3.3.5.2(Test circuits and connections)	-	500	-
8.3.4.3(Test circuit and test quantities)	-	0	-
8.3.4.2(Performance under conditional short-circuit current : Test procedure)	-	50000	-
8.3.4.1(General conditions for short-circuit tests)	-	0	-
8.3.4.4 b)(Condition of the switching element after the test)	-	10000	-
8.3.4.4 a)(Condition of the switching element after the test)	-	10000	-
8.4.2.4(Surges)	-	50000	-
8.3.1(Degree of protection of enclosed control circuit devices)	-	60000	-
C.3(Electrical durability)	-	144000	-
C.2(Mechanical durability)	-	96000	-
C.1.2(Observation)	-	500	-
F 8.1.2.6("Dielectric test after stresses")	-	15000	-
F 8.1.2.4(Impact test)	-	5000	-
F.8.1.2.3("Rapid change of temperature test")	-	80000	-
F.8.1.2.5(Damp heat, cyclic)	-	80000	-
F.8.1.2.4(Impact test)	-	5000	-
F.8.1.2.1(Dielectric tests in new conditions)	-	15000	-
G.8.2.5(Bend test)	-	10000	-
G.8.2.4(Push test)	-	10000	-
G.8.2.3(Torque test)	-	10000	-
G.8.2.2(Pull-out test)	-	10000	-
H.8.7("Verification of electromagnetic compatibility")	-	420000	-
H.8.6("Performance under short circuit current conditions")	-	50000	-
H.8.5("Making and breaking capacities")	-	80000	-
H.8.4(OFF-state current)	-	5000	-
H.8.2(Voltage drop test)	-	5000	-
J.8.5("Degree of protection for indicating towers")	-	60000	-
J.8.4.3(Indirect support mounting)	-	500	-
J.8.4.2.3(Vibration)	-	60000	-
J.8.4.2.2(Shock)	-	60000	-
J.8.3.4("Short Circuit test (on built-in transformers, if any)")	-	50000	-
J.8.3.3.3(Temp-rise tests)	-	25000	-
J.8.3.3.4.3("Dielectric test (indicator lights with built-in transformers)")	-	15000	-
J.8.3.3.4(Dielectric test)	-	15000	-
J.7.1.12(Indicator lights with built-in transformers)	-	15000	-
J.7("Constructional requirements")	-	500	-
K 8.3.4("Performance under conditional shortcircuit current")	-	50000	-
K 8.3.7(Verification of robustness of the actuating system)	-	5000	-
K 8.3.5(Verification of mechanical operation of position switches at limits of temperature)	-	5000	-
K.8.3.6(Verification of direct opening action)	-	50000	-
L.8.4(Special test for mechanically linked contact elements)	-	50000	-
N.3(Method based on durability test results)	-	50000	-
L.8.4(Special test for mechanically linked contact elements)	-	50000	-
K.8.3.6(Verification of direct opening action)	-	50000	-
5.2.1(" Marking : General ")	-	0	-
K 8.3.5(Verification of mechanical operation of position switches at limits of temperature)	-	0	-
K 8.3.7(Verification of robustness of the actuating system)	-	0	-
K 8.3.4("Performance under conditional shortcircuit current")	-	0	-
5.2.2(Terminal identification and marking)	-	0	-
J.7("Constructional requirements")	-	0	-
5.2.3(Functional markings)	-	0	-
J.7.1.12(Indicator lights with built-in transformers)	-	0	-
J.8.3.3.4(Dielectric test)	-	0	-
5.2.4(Emergency stop)	-	0	-
J.8.3.3.4.3("Dielectric test (indicator lights with built-in transformers)")	-	0	-
J.8.3.3.3(Temp-rise tests)	-	0	-
J.8.3.4("Short Circuit test (on built-in transformers, if any)")	-	0	-
5.2.5(Operating diagram)	-	0	-
J.8.4.2.2(Shock)	-	0	-
5.2.5.1(Position indication)	-	0	-
J.8.4.2.3(Vibration)	-	0	-
J.8.4.3(Indirect support mounting)	-	0	-
5.2.5.2(Terminal markings for operating diagrams)	-	0	-
J.8.5("Degree of protection for indicating towers")	-	0	-
5.2.6(Time delay markings)	-	0	-
H.8.2(Voltage drop test)	-	0	-
5.3(Instructions for installation, operation and maintenance)	-	0	-
H.8.4(OFF-state current)	-	0	-
H.8.5("Making and breaking capacities")	-	0	-
7.1.2.2(Glow-wire testing)	-	0	-
H.8.6("Performance under short circuit current conditions")	-	0	-
7.1.3(Current-carrying parts and their connections)	-	0	-
H.8.7("Verification of electromagnetic compatibility")	-	0	-
G.8.2.2(Pull-out test)	-	0	-
7.1.4 of IEC 60947-1:2007 (Sequence 6)(Measurement of Clearances and creepage distances)	-	0	-
G.8.2.3(Torque test)	-	0	-
7.2.4.1(Making and breaking capacities)	-	0	-
7.2.4.1(Making and breaking capacities)	-	0	-
G.8.2.4(Push test)	-	0	-
G.8.2.5(Bend test)	-	0	-
F.8.1.2.1(Dielectric tests in new conditions)	-	0	-
7.2.4.3(Durability)	-	0	-
F.8.1.2.4(Impact test)	-	0	-
7.3.2.4(Electrostatic discharges)	-	0	-
F.8.1.2.5(Damp heat, cyclic)	-	0	-
F.8.1.2.3("Rapid change of temperature test")	-	0	-
7.3.2.6(Electrical fast transients/bursts)	-	0	-
F 8.1.2.4(Impact test)	-	0	-
F 8.1.2.6("Dielectric test after stresses")	-	0	-
C.1.2(Observation)	-	0	-
7.3.2.7(Surges)	-	0	-
C.2(Mechanical durability)	-	0	-
7.3.2.8(Conducted disturbances induced by radio-frequency fields)	-	0	-
C.3(Electrical durability)	-	0	-
7.3.2.9(Power-frequency magnetic fields)	-	0	-
Annex C of IEC 60947-1:2007 (Sequence 5)(Degree of protection of enclosed control circuit devices)	-	0	-
8.4.2.4(Surges)	-	0	-
7.3.2.10(Voltage dips and interruptions)	-	0	-
8.3.4.4 a)(Condition of the switching element after the test)	-	0	-
8.3.4.4 b)(Condition of the switching element after the test)	-	0	-
8.3.4.1(General conditions for short-circuit tests)	-	0	-
8.3.4.2(Performance under conditional short-circuit current : Test procedure)	-	0	-
8.3.4.3(Test circuit and test quantities)	-	0	-
7.3.3(Emission)	-	0	-
8.3.3.5.2(Test circuits and connections)	-	0	-
8.3.3.5(Making and breaking capacities)	-	0	-
8.3.3.2(Operating limits of contactor relays)	-	0	-
7.2.3(Dielectric properties)	-	0	-
8.3.3.4(Dielectric properties)	-	0	-
8.3.3.3(Temperature rise)	-	0	-
8.1.5(Special tests)	-	0	-
8.2.7(Conduit pull-out test, torque test and bending test with metallic conduits)	-	0	-
8.2.6 (Sequence 6)(Verification of limitation of rotation (of a rotary switch))	-	0	-
8.2.1.1(Test of resistance to abnormal heat and fire)	-	0	-
8.2.5 (Sequence 5)(Verification of actuating force (or moment))	-	0	-
8.2.4.5(Test for insertability of unprepared round copper conductors having the maximum cross-section)	-	0	-
8.2.1.1.1(Glow-wire test)	-	0	-
8.2.4.4(Pull-out test)	-	0	-
8.2.4.3(Testing for damage to and accidental loosening of conductors (flexion test))	-	0	-
8.2.1.1.2(Flammability, hot wire ignition and arc ignition tests (on materials))	-	0	-
8.2.4.2(Tests of mechanical strength of terminals)	-	0	-
8.2.4(Mechanical and electrical properties of terminals)	-	0	-
8.2.3(Enclosures for equipment)	-	0	-
8.3.3.5.6 b(Dielectric verification)	-	0	-
8.3.4(Performance under Conditional Short-Circuit Current)	-	0	-
8.3.3.5.3(Making and breaking capacities of switching elements under abnormal conditions)	-	0	-
8.3.3.5.4(Making and breaking capacities of switching elements under abnormal conditions)	-	0	-
7.3.2.11(Harmonics in the supply)	-	0	-
7.3.2.11(Harmonics in the supply)	-	0	-

12 May, 2027

-
Included w.e.f.18.02.2025 Exclusion Cl 7.3.2.11 (Harmonics in the supply) Cl 8.2.1.1.2 (Flammability, hot wire ignition and arc ignition tests (on materials)) Cl 8.2.3 (Enclosures for equipment) Cl 8.3.1 (Degree of protection of enclosed control circuit devices) Cl H.8.7 ("Verification of electromagnetic compatibility") Cl J.8.5 ("Degree of protection for indicating towers") Cl J.8.5 ("Degree of protection for indicating towers") Cl 8.2.1.1.2 (Flammability, hot wire ignition and arc ignition tests (on materials)) Cl 8.2.3 (Enclosures for equipment) Cl 7.3.2.11 (Harmonics in the supply)

IS 12640 : Part 1 (2016)

Residual current operated circuitBreakers without integral overcurrent protection for household and similar uses (Rccbs): Part 1 general rules (Second Revision)

RCCB

1545000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking)	-	500	For DP = 500, FP = 500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
8.1.1(General)	-	500	For DP = 500, FP = 500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
8.1.2(Mechanism)	-	1500	For DP = 1000, FP = 1500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.3(Indelibility of marking)	-	1000	For DP = 1000, FP = 1000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
8.1.3 (Creepage distances)	-	1500	For DP = 1000, FP = 1500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
8.1.3 i)(Clearance )	-	1500	For DP = 1000, FP = 1500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.15(Trip-free mechanism)	-	3500	For DP = 2500, FP = 3500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.4(Test of reliability of screws, current carrying parts and connections )	-	5000	For DP = 3000, FP = 5000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.5(Test of reliability of terminals for external conductors)	-	5500	For DP = 3500, FP = 5500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.6(Protection against electric shock)	-	4000	For DP = 2000, FP = 4000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.13(Test of resistance to heat)	-	2500	For DP = 2000, FP = 2500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
8.1.3(Clearances and creepage distances (internal parts) Clearances distances)	-	1500	For DP = 1000, FP = 1500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.1(Dielectric Properties : Resistance to humidity)	-	15000	For DP = 15000, FP = 15000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.2 (Insulation resistance of main circuit)	-	7500	For DP = 5000, FP = 7500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.7.1(Rated impulse withstand voltage)	-	13500	For DP = 11000, FP = 13500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.8(Test of Temperature rise)	-	18000	For DP = 15000, FP = 18000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.22.2(Testing with temperature of 40)	-	38000	For DP = 30000, FP = 38000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.23(Verification of ageing of electronic components )	-	25500	For DP = 23000, FP = 25500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.11.2.3(VERIFICATION OF PERFORMANCE AT Im)	-	60000	For DP = 49000, FP = 60000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.16 a)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	For DP = 2000, FP = 3000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.16 b)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	For DP = 2000, FP = 3000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.16 c)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	For DP = 2000, FP = 3000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.12.1(Verification of resistance to mechanical shock)	-	11000	For DP = 9000, FP = 11000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.18.1(Verification of the limiting value of overcurrent in case of a load through an RCCB with two current paths)	-	11000	For DP = 9000, FP = 11000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.11.2.4 (Verification of the coordination between the RCCB and the SCPD)	-	75000	For DP = 60000, FP = 75000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.22.1(Climatic test)	-	90000	For DP = 90000, FP = 90000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.19.1( Verification of behaviour of RCCBs in case of current surges caused by impulse voltages (Current surge test for all RCCBs (0,5 µs/100 kHz ring wave test)))	-	16000	For DP = 12000, FP = 16000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.19.2(Verification of behaviour at surge currents up to 3000A (8/20 s surge current test))	-	16000	For DP = 12000, FP = 16000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.25(Resistance to rusting)	-	3000	For DP = 2000, FP = 3000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.14(Resistance to abnormal heat and to fire)	-	20000	For DP = 15000, FP = 20000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.7.4(Resistance of the insulation of open contacts and basic insulation against an impulse voltage in normal conditions)	-	13500	For DP = 11000, FP = 13500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.7.5(Verification of the behaviour of components bridging the basic insulation)	-	12000	For DP = 10000, FP = 12000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.3(Dielectric strength of the main circuit)	-	7500	For DP = 5000, FP = 7500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.4(Insulation resistance and dielectric strength of auxiliary circuits)	-	7500	For DP = 5000, FP = 7500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.7.2(Verification of clearances with the impulse withstand voltage)	-	13500	For DP = 11000, FP = 13500, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.5(Secondary circuit of detection transformers)	-	11000	For DP = 10000, FP = 11000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.7.6(Capability of control circuits connected to the main circuits etc.)	-	11000	For DP = 10000, FP = 11000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.10(Mechanical and electrical endurance)	-	120000	For DP = 80000, FP = 120000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.9(Residual operating characteristics)	-	90000	For DP = 60000, FP = 90000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.17(Behaviour in the case of failure of the line voltage)	-	8000	For DP = 6000, FP = 8000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.21(DC components)	-	11000	For DP = 8000, FP = 11000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
(9.11.2.3c)(Verification of the suitability of RCCBs for use in IT-systems)	-	80000	For DP = 60000, FP = 80000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
(9.11.2.4 c)(Coordination at IΔc)	-	75000	For DP = 60000, FP = 75000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.11.2.2(Performance at Im)	-	75000	For DP = 60000, FP = 75000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.24 Annex-A, Test Sequence-H(Surges)	-	90000	For DP = 60000, FP = 90000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.24 Annex-A, Test Sequence-I(Conducted sine-wave form voltages or currents)	-	60000	For DP = 60000, FP = 60000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.24 Annex-A, Test Sequence-I(Radiated electromagnetic field)	-	120000	For DP = 120000, FP = 120000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.24 Annex-A, Test Sequence-I(Fast transients (bursts))	-	90000	For DP = 60000, FP = 90000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.24 Annex-A, Test Sequence-J(Conducted common mode disturbances)	-	135000	For DP = 90000, FP = 135000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
9.24 Annex-A, Test Sequence-J(Electrostatic discharges)	-	20000	For DP = 20000, FP = 20000, Total 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP),
6(Marking)	-	500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
8.1.1(General)	-	500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
8.1.2(Mechanism)	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
9.3(Indelibility of marking)	-	1000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
8.1.3 (Creepage distances)	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
8.1.3 i)(Clearance )	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
9.15(Trip-free mechanism)	-	3500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2500 FP-3500
9.4(Test of reliability of screws, current carrying parts and connections )	-	5000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-3000 FP-5000
9.5(Test of reliability of terminals for external conductors)	-	5500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-3500 FP-5500
9.6(Protection against electric shock)	-	4000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-4000
9.13(Test of resistance to heat)	-	2500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-2500
8.1.3(Clearances and creepage distances (internal parts) Clearances distances)	-	1500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-1000 FP-1500
9.7.1(Dielectric Properties : Resistance to humidity)	-	15000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.2 (Insulation resistance of main circuit)	-	7500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-5000 FP-7500
9.7.7.1(Rated impulse withstand voltage)	-	13500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-11000 FP-13500
9.8(Test of Temperature rise)	-	18000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-15000 FP-18000
9.22.2(Testing with temperature of 40)	-	38000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-30000 FP-38000
9.23(Verification of ageing of electronic components )	-	25500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-23000 FP-25500
9.11.2.3(VERIFICATION OF PERFORMANCE AT Im)	-	60000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-49000 FP-60000
9.16 a)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-3000
9.16 b)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-3000
9.16 c)(Verification of the operation of the test device at the limits of rated voltage )	-	3000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-2000 FP-3000
9.12.1(Verification of resistance to mechanical shock)	-	11000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-9000 FP-11000
9.18.1(Verification of the limiting value of overcurrent in case of a load through an RCCB with two current paths)	-	11000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-9000 FP-11000
9.11.2.4 (Verification of the coordination between the RCCB and the SCPD)	-	75000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-60000 FP-75000
9.22.1(Climatic test)	-	90000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.19.1( Verification of behaviour of RCCBs in case of current surges caused by impulse voltages (Current surge test for all RCCBs (0,5 µs/100 kHz ring wave test)))	-	16000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-12000 FP-16000
9.19.2(Verification of behaviour at surge currents up to 3000A (8/20 s surge current test))	-	16000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP) DP-12000 FP-16000
9.25(Resistance to rusting)	-	3000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.14(Resistance to abnormal heat and to fire)	-	20000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.7.4(Resistance of the insulation of open contacts and basic insulation against an impulse voltage in normal conditions)	-	13500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.7.5(Verification of the behaviour of components bridging the basic insulation)	-	12000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.3(Dielectric strength of the main circuit)	-	7500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.4(Insulation resistance and dielectric strength of auxiliary circuits)	-	7500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.7.2(Verification of clearances with the impulse withstand voltage)	-	13500	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.5(Secondary circuit of detection transformers)	-	11000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.7.6(Capability of control circuits connected to the main circuits etc.)	-	11000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.10(Mechanical and electrical endurance)	-	120000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.9(Residual operating characteristics)	-	90000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.17(Behaviour in the case of failure of the line voltage)	-	8000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.21(DC components)	-	11000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
(9.11.2.3c)(Verification of the suitability of RCCBs for use in IT-systems)	-	80000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
(9.11.2.4 c)(Coordination at IΔc)	-	75000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.11.2.2(Performance at Im)	-	75000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.24 Annex-A, Test Sequence-H(Surges)	-	90000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.24 Annex-A, Test Sequence-I(Conducted sine-wave form voltages or currents)	-	60000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.24 Annex-A, Test Sequence-I(Radiated electromagnetic field)	-	120000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.24 Annex-A, Test Sequence-I(Fast transients (bursts))	-	90000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.24 Annex-A, Test Sequence-J(Conducted common mode disturbances)	-	135000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)
9.24 Annex-A, Test Sequence-J(Electrostatic discharges)	-	20000	Complete testing charges- 1220000 (For3 samples of DP) & 1545000 (For3 samples of FP)

12 May, 2027

-
Included w.e.f, 10/04/2020 Exclusion : Cl.9.24 Annex-A, Test Sequence-H (Harmonics, inter harmonics), Cl.9.24 Annex-A, Test Sequence-H (Signalling voltages).

IS 12640 : Part 2 (2016)

Residual current operated circuit - Breakers with integral overcurrent protection for household and similar uses (Rcbos): Part 2 general rules

RCBO

1775000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.3(Clearances and creepage distances (internal parts))	-	1500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-1000 FP-1500
9.7.1(Resistance to humidity)	-	15000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-15000 FP-15000
9.7.2(Insulation resistance of main circuit)	-	7500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-5000 FP-7500
9.7.3 a)(Dielectric strength of the main circuit)	-	7500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-5000 FP-7500
9.7.6(Capability of control circuits connected to the main circuit in respect of withstanding high d.c. voltages due to insulation measurements )	-	11000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-10000 FP-11000
9.8(Test of temperature-rise )	-	18000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-15000 FP-18000
9.22.2(Test with temperature of 40 ºC)	-	38000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-30000 FP-38000
9.12.11.2(PERFORMANCE AT REDUCED SHORT-CIRCUIT CURRENTS)	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-70000 FP-90000
9.12.12.1(VERIFICATION OF THE RCBO AFTER SHORT-CIRCUIT TEST : DIELECTRIC STRENGTH TEST)	-	110000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-80000 FP-110000
9.9.1.2(Verification of the operating characteristic under residual current conditions)	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-60000 FP-90000
9.16(Verification of the operation of the test device at the limits of rated voltage )	-	4000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-3000 FP-4000
9.13.1(Verification of resistance to mechanical shock )	-	11000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-9000 FP-11000
9.12.11.3(SHORT-CIRCUIT PERFORMANCE AT 1500 A)	-	139000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-101000 FP-139000
9.12.11.4(TEST AT SERVICE SHORT-CIRCUIT CAPACITY (Ics)	-	120000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-90000 FP-120000
9.22.1(Reliability (Climatic test))	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-90000 FP-90000
9.19.1(Current surge test for all RCBOs (0,5 µs/100 kHz ring wave test))	-	16000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-12000 FP-16000
6, 9.3(Indelibility of marking)	-	1500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) Cl.#6 - DP=500, FP=500 Cl.#9.3, DP=1000, FP=1000
8.1.2 , 9.11(Trip-free mechanism)	-	5000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) Cl.#8.1.2 - DP=800, FP=1500 Cl.#9.3, DP=2100, FP=3500
9.4(Reliability of screws, current-carrying parts and connections)	-	5000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-3000 FP-5000
9.5(Test of reliability of screw-type terminals for external)	-	5500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-3500 FP-5500
9.6(Protection against electric shock)	-	3200	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-2000 FP-3200
9.14(Resistance to heat)	-	2500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-1800 FP-2500
9.25(Resistance to rusting)	-	3000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-2000 FP-3000
9.15(Resistance to abnormal heat and to fire)	-	20000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-15000 FP-20000
9.7.7.4(Resistance of the insulation of open contacts and basic insulation against an impulse voltage in normal conditions)	-	13500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-11000 FP-13500
9.7.7.5(Verification of the behavior of components bridging the basic insulation)	-	12000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-10000 FP-12000
9.7.4(Insulation resistance and dielectric strength of auxiliary circuits)	-	7500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-5000 FP-7500
9.7.7.1(testing procedure for the impulse withstand voltage tests)	-	13500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-11000 FP-13500
9.7.7.2(Verification of clearances with the impulse withstand voltage)	-	13500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-11000 FP-13500
9.7.5(Secondary circuit of detection transformers)	-	11000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-10000 FP-11000
9.7.7.3(Verification of leakage currents across open contacts)	-	2000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-1000 FP-2000
9.23(Ageing of electronic components)	-	25500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-23000 FP-25500
9.10(Mechanical and electrical endurance)	-	70000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-50000 FP- 70000
9.17(Behaviour in case of failure of the line voltage)	-	8000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-6000 FP-8000
9.19(Behaviour in case of surge currents)	-	16000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-12000 FP-16000
9.21(DC components)	-	11000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-8000 FP-11000
9.12.13(Performance at IΔm)	-	70000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-57000 FP-70000
9.9.2(Overcurrent operating characteristics)	-	70000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-40000 FP-70000
9.12.11.4 b) (and 9.12.12)(Performance at service short-circuit capacity)	-	120000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-90000 FP-120000
9.12.11.4 c) (and 9.12.12.2)(Performance at rated short-circuit capacity)	-	120000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-90000 FP-120000
9.24 Annex-A, Test Sequence-H(Surges)	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-60000 FP-90000
9.24 Annex-A, Test Sequence-I(Conducted sine-wave form voltages or currents)	-	60000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-60000 FP- 60000
9.24 Annex-A, Test Sequence-I(Radiated electromagnetic field)	-	120000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-120000 FP-120000
9.24 Annex-A, Test Sequence-I(Fast transients (bursts))	-	90000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-60000 FP-90000
9.24 Annex-A, Test Sequence-J(Conducted common mode disturbances)	-	135000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-90000 FP-135000
9.24 Annex-A, Test Sequence-J(Electrostatic discharges)	-	20000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-20000 FP- 20000
8.1.1(General)	-	500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-500 FP- 500
8.1.6(Noninterchangeability)	-	800	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-800 FP- 800
9.12.11.2.2(Short circuit test for verifying suitability of RCBOs for use in IT-systems)	-	110000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-80000 FP-110000
9.7.1(Resistance to humidity)	-	15000	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP)
6, 9.3(Indelibility of marking)	-	0	-
8.1.2 , 9.11(Trip-free mechanism)	-	0	-
9.4(Reliability of screws, current-carrying parts and connections)	-	0	-
9.5(Test of reliability of screw-type terminals for external)	-	0	-
9.6(Protection against electric shock)	-	0	-
9.14(Resistance to heat)	-	0	-
9.25(Resistance to rusting)	-	0	-
9.15(Resistance to abnormal heat and to fire)	-	0	-
9.7.7.4(Resistance of the insulation of open contacts and basic insulation against an impulse voltage in normal conditions)	-	0	-
9.7.7.5(Verification of the behavior of components bridging the basic insulation)	-	0	-
9.7.4(Insulation resistance and dielectric strength of auxiliary circuits)	-	0	-
9.7.7.1(testing procedure for the impulse withstand voltage tests)	-	0	-
9.7.7.2(Verification of clearances with the impulse withstand voltage)	-	0	-
9.7.5(Secondary circuit of detection transformers)	-	0	-
9.7.7.3(Verification of leakage currents across open contacts)	-	0	-
9.23(Ageing of electronic components)	-	0	-
9.10(Mechanical and electrical endurance)	-	0	-
9.17(Behaviour in case of failure of the line voltage)	-	0	-
9.19(Behaviour in case of surge currents)	-	0	-
9.21(DC components)	-	0	-
9.12.13(Performance at IΔm)	-	0	-
9.9.2(Overcurrent operating characteristics)	-	0	-
9.12.11.4 b) (and 9.12.12)(Performance at service short-circuit capacity)	-	0	-
9.12.11.4 c) (and 9.12.12.2)(Performance at rated short-circuit capacity)	-	0	-
9.24 Annex-A, Test Sequence-H(Surges)	-	0	-
9.24 Annex-A, Test Sequence-I(Conducted sine-wave form voltages or currents)	-	0	-
9.24 Annex-A, Test Sequence-I(Radiated electromagnetic field)	-	0	-
9.24 Annex-A, Test Sequence-I(Fast transients (bursts))	-	0	-
9.24 Annex-A, Test Sequence-J(Conducted common mode disturbances)	-	0	-
9.24 Annex-A, Test Sequence-J(Electrostatic discharges)	-	0	-
8.1.1(General)	-	500	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-500 FP-500
8.1.6(Noninterchangeability)	-	800	Complete testing charges- 1370000 (For3 samples of DP) & 1775000 (For3 samples of FP) DP-800 FP-800

12 May, 2027

-
Included w.e.f, 10/04/2020 Exclusion : Cl.9.24 Annex-A, Test Sequence-H (Harmonics, inter harmonics), Cl.9.24 Annex-A, Test Sequence-H (Signalling voltages).

IS/IEC 60947 : PART 3 (2020)

Low-Voltage Switchgear and Controlgear: Part 3 Switches Disconnectors Switch-Disconnectors and Fuse-Combination Units

Switches, Disconnectors, SD, SDF

677850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
4(Classification)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.2(Rated voltages)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.2.1(Rated operational voltage)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.2.2(Rated insulation voltage)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.2.3(Rated impulse withstand voltage)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.3(Currents)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.3.2(Conventional free air thermal current)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.3.3(Conventional enclosed thermal current)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.3.4(Rated operational current (Ie) or rated operational power)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.3.5(Rated uninterrupted current)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.4(Rated frequency)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.5(Rated duty)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.5.2(Eight-hour duty)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.5.3(Uninterrupted duty)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.6.1(Ability to withstand motor switching overload currents)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.6.2(Rated making capacity)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.6.3(Rated breaking capacity)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.7(Short-circuit characteristics)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.7.1(Rated short-time withstand current)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.7.2(Rated short-circuit making capacity)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.3.7.4(Rated conditional short-circuit current)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.4(Utilization category)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.5(Control circuits)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.6(Auxiliary circuits)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.7(Relays and releases)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
5.8(Co-ordination with short-circuit protective devices (SCPD))	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
6.2.2(Marking)	-	500	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
6.3(Instructions for installation, operation and maintenance, decommissioning and dismantling)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
7(Normal service, mounting and transport conditions)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.1.1(General)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.1.2.2(Glow wire testing)	-	25000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.1.7.1(General)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.1(Operating conditions)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.1.1(General)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.1.2(Limits of operation of power operated equipment)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.1.3(Limits of operation of under-voltage relays and releases)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.1.4(Limits of operation of shunt releases)	-	0	No test 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.2(Temperature-rise)	-	22150	SP/SPN/DP - 18500 TP/TPN/FP - 22150 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.3(Dielectric properties)	-	22000	SP/SPN/DP - 18000 TP/TPN/FP - 22000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.3.2(Impulse withstand voltage)	-	15150	SP/SPN/DP - 12500 TP/TPN/FP - 15150 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.3.3(Power-frequency or DC withstand voltage of the main, auxiliary and control circuits)	-	7000	SP/SPN/DP - 6500 TP/TPN/FP - 7000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.4(Ability to make and break under no-load, normal load and overload conditions)	-	35000	SP/SPN/DP - 28000 TP/TPN/FP - 35000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.4.1(Making and breaking capacities)	-	35000	SP/SPN/DP - 28000 TP/TPN/FP - 35000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.4.2(Operational performance)	-	35000	SP/SPN/DP - 28000 TP/TPN/FP - 35000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.4.3(Mechanical durability)	-	144000	SP/SPN/DP - 96000 TP/TPN/FP - 144000 Considered The numbers of operating cycles as 1 million for each Mechanical Durability 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.4.4(Electrical durability)	-	174000	SP/SPN/DP - 120000 TP/TPN/FP - 174000 Considered The numbers of operating cycles as 1 million for each Mechanical Durability 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.5(Ability to make, break or withstand short-circuit currents)	-	49700	SP/SPN/DP - 46300 TP/TPN/FP - 49700 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.7(Additional performance requirements for equipment suitable for isolation)	-	49700	SP/SPN/DP - 46300 TP/TPN/FP - 49700 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.8(Critical load current performance: DC equipment)	-	55000	SP/SPN/DP - 45000 TP/TPN/FP - 55000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.2.9(Overload requirements for equipment incorporating fuses)	-	49700	SP/SPN/DP - 46300 TP/TPN/FP - 49700 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.1.3.2(Mechanical operation test)	-	45000	SP/SPN/DP - 35000 TP/TPN/FP - 45000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.1.3.2(Mechanical operation test)	-	45000	SP/SPN/DP - 35000 TP/TPN/FP - 45000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.1.3.3(Dielectric test)	-	7000	SP/SPN/DP - 6500 TP/TPN/FP - 7000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.1.4(Sampling tests)	-	22000	SP/SPN/DP - 18000 TP/TPN/FP - 22000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.1.5Special tests(Special tests)	-	504000	Covering DAMP HEAT, Salt mist, vibration and shock tests Damp heat: 220000 Salt mist: 104000 Vibration: 120000 Shock test: 60000 (For 1 set of samples for all sequences)
9.2(Compliance with constructional requirements)	-	460000	Glow wire & flammability (NF): 120000 Annex C IP tests: 90000 (IPXX) Mech. & Electrical properties of terminal: 2 (For 1 set of samples for all sequences) 50000
9.3.3.6(DC test current ripple)	-	7000	SP/SPN/DP - 6500 TP/TPN/FP - 7000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.2(Temperature-rise)	-	22150	SP/SPN/DP - 18500 TP/TPN/FP - 22150 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.3(Test of dielectric properties)	-	22000	SP/SPN/DP - 18000 TP/TPN/FP - 22000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.4(Making and breaking capacities)	-	35000	SP/SPN/DP - 28000 TP/TPN/FP - 35000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.4.3(Characteristics of transient recovery voltage)	-	22150	SP/SPN/DP - 18500 TP/TPN/FP - 22150 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.5(Dielectric verification)	-	7000	SP/SPN/DP - 6500 TP/TPN/FP - 7000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.6(Leakage current)	-	5000	SP/SPN/DP - 3500 TP/TPN/FP - 5000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.5.2(Operational performance test)	-	40450	SP/SPN/DP - 36800 TP/TPN/FP - 40450 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.6.2(Short-time withstand current test)	-	26250	SP/SPN/DP - 25000 TP/TPN/FP - 26250 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.6.3(Short-circuit making capacity test)	-	49700	SP/SPN/DP - 46300 TP/TPN/FP - 49700 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.7.2(Circuit-breaker protected short-circuit withstand)	-	75950	SP/SPN/DP - 71300 TP/TPN/FP - 75950 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.7.3(Fuse protected short-circuit withstand)	-	75950	SP/SPN/DP - 71300 TP/TPN/FP - 75950 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.8.2(Overload test)	-	8000	SP/SPN/DP - 6000 TP/TPN/FP - 8000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.9.2(Determination of critical load current)	-	20000	SP/SPN/DP - 15000 TP/TPN/FP - 20000 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.4(Electromagnetic compatibility tests)	-	430000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.5.2(Mechanical durability)	-	96000	Considered The numbers of operating cycles as 1 million for each Mechanical and Electrical Durability 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.5.3(Electrical durability)	-	144000	Considered The numbers of operating cycles as 1 million for each Mechanical and Electrical Durability 590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.5.4(Damp heat, salt mist, vibration and shock)	-	504000	Damp heat: 220000 Salt mist: 104000 Vibration: 120000 Shock test: 60000 (For 1 set of samples for all sequences)
D.7.1.1(Ambient air temperature)	-	1000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
D.8.1.4(Clearances and creepage distances)	-	25000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
D.8.1.12(Degrees of protection of enclosed equipment)	-	120000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
D.9.3.11(Climatic test)	-	220000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
D.9.3.12(Temperature-rise verification with solar effects – Outdoor units only)	-	23000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
E.9.2(Current cycling test)	-	300000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences for 10 Days of testing)
E.9.2.4(Temperature measurements)	-	23000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
E.9.3.1(Flexion test)	-	15000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
E.9.3.2(Pull-out test)	-	10000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.1.7.2(Additional constructional requirements)	-	100000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
8.1.9(Additional requirements for equipment provided with a neutral pol)	-	75000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.7(Temperature-rise verification)	-	23000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.4.8(Strength of actuator mechanism)	-	5000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.5.3(Dielectric verification)	-	7000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.5.5(Temperature-rise verification)	-	23000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.6.4(Dielectric verification)	-	7000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.6.6(Temperature-rise verification)	-	23000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.7.4(Dielectric verification)	-	7000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.7.6(Temperature-rise verification)	-	23000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.8.3(Dielectric verification)	-	7000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.8.5(Temperature-rise verification)	-	23000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.9.3(Critical load current performance)	-	55000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.5.4(Leakage current)	-	5000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.6.5(Leakage current)	-	5000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.7.5(Leakage current)	-	5000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.3.8.4(Leakage current)	-	5000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.4.2(Immunity)	-	220000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)
9.4.3(Emission)	-	210000	590200 for SP/SPN/DP 677850 for TP/TPN/FP (For 1 set of samples for all sequences)

12 May, 2027

-
Product rating : Up to 63A/Max. 690V AC, Short circuit test at max. 15KA AC, Included .w.e.f.11.02.2025 Exclusion Cl D.9.3.10 (Thermal cycling test) Cl D.8.1.12 (Degrees of protection of enclosed equipment) Cl 9.2 (Compliance with constructional requirements)

IS 12640 : Part 1 (2024)

Residual current operated circuitBreakers without integral overcurrent protection for household and similar uses Rccbs: Part 1 general rules (Third Revision)

RCCB

1545000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking)	-	500	500 (For 1 Sample of DP), 500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
8.1.1(General)	-	500	500 (For 1 Sample of DP), 500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
8.1.2(Mechanism)	-	1500	1000 (For 1 Sample of DP), 1500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.3(Indelibility of marking)	-	1000	1000 (For 1 Sample of DP), 1000 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
8.1.3(Clearance and creepage distance (External parts only))	-	1500	1000 (For 1 Sample of DP) 1500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.15(Trip free mechanism)	-	3500	2500 (For 1 Sample of DP) 3500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.4(Reliability of screws, current-carrying parts and connections)	-	5000	3000 (For 1 Sample of DP) 5000 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.5(Reliability of terminals for external conductors)	-	5500	3500 (For 1 Sample of DP) 5500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.6(Protection againts electrci shock)	-	4000	2000 (For 1 Sample of DP) 4000 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.13(Resistance to heat)	-	2500	2000 (For 1 Sample of DP) 2500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
8.1.3(Clearance and creepage distance (Internal parts only))	-	1500	1000 (For 1 Sample of DP) 1500 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.25(Resistance to rusting)	-	3000	2000 (For 1 Sample of DP) 3000 (For 1 Sample of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.14(Resistance to abnormal heat and to fire)	-	20000	15000 (For 3 Samples of DP) 20000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.7.4(Resistance of the insulation of open contacts and basic insulation against an impulse voltage in normal conditions)	-	13500	11000 (For 3 Samples of DP) 13500 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.7.5(Verification of the behaviour of components bridging the basic insulation)	-	12000	10000 (For 3 Samples of DP) 12000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.1(Resistance to humidity)	-	15000	15000 (For 3 Samples of DP) 15000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.2(Insulation resistance of the main circuit)	-	7500	5000 (For 3 Samples of DP) 7500 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.3(Dielectric strength of the main circuit)	-	7500	5000 (For 3 Samples of DP) 7500 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.4(Insulation resistance and dielectric strength of auxiliary circuits)	-	7500	5000 (For 3 Samples of DP) 7500 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.7.2(Verification of clearances with the impulse withstand voltage)	-	13500	11000 (For 3 Samples of DP) 13500 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.5(Secondary circuit of detection transformers)	-	11000	10000 (For 3 Samples of DP) 11000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.7.6(Capability of control circuits connected to the main circuits etc.)	-	11000	10000 (For 3 Samples of DP) 11000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.8(Temperature-rise)	-	18000	15000 (For 3 Samples of DP) 18000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.22.2(Reliability at 40 °C)	-	38000	30000 (For 3 Samples of DP) 38000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.23(Ageing of electronic components)	-	25500	23000 (For 3 Samples of DP) 25500 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.10(Mechanical and electrical endurance)	-	120000	80000 (For 3 Samples of DP) 120000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.9(Residual operating characteristics)	-	101000	68000 (For 3 Samples of DP) 101000 (For 3 Samples of FP) - These tests charges are including 9.21 - DC component as per latest revision. Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.17(Behaviour in the case of failure of the line voltage)	-	8000	6000 (For 3 Samples of DP) 8000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.11.2.3a)b)(Perf ormance at IΔm)	-	60000	49000 (For 3 Samples of DP) 60000(For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.16(Test device)	-	3000	2000 (For 3 Samples of DP) 3000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.12(Resistance to mechanical shock and impact)	-	11000	9000 (For 3 Samples of DP) 11000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.18(Non-operating current under overcurrent conditions)	-	11000	9000 (For 3 Samples of DP) 11000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.11.2.3c)(Verification of the suitability of RCCBs for use in IT-systems)	-	80000	60000 (For 3 Samples of DP) 80000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.11.2.4 a)(Coordination at Inc)	-	75000	60000 (For 3 Samples of DP) 75000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.11.2.4 c)(Performance at Im)	-	75000	60000 (For 3 Samples of DP) 75000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.11.2.4 b)(Coordination at Im)	-	75000	60000 (For 3 Samples of DP) 75000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.11.2.2(Coordination at IΔc)	-	75000	60000 (For 3 Samples of DP) 75000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.22.1(Reliability (climatic test))	-	90000	90000 (For 3 Samples of DP) 90000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
IEC 61543, Table 5 –T2.3(Surges)	-	90000	60000 (For 3 Samples of DP) 90000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
IEC 61543, Table 5 -T2.1(Conducted s ine-wave form voltages or c urrents)	-	60000	60000 (For 3 Samples of DP) 60000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
IEC 61543, Table 5 -T2.1(Conducted s ine-wave form voltages or c urrents)	-	0	Duplicate clause
IEC 61543, Table 5 -T2.5(Radiated electromagnetic field)	-	120000	120000 (For 3 Samples of DP) 120000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
IEC 61543, Table 5 -T2.2(Fast transients (bursts))	-	90000	60000 (For 3 Samples of DP) 90000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
IEC 61543, Table 5 – T2.6(Conducted common mode disturbances in the frequency range lower than 150 kHz)	-	135000	90000 (For 3 Samples of DP) 135000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
IEC 61543, Table 6 -T3.1(Electrostatic discharges)	-	20000	20000 (For 3 Samples of DP) 20000 (For 3 Samples of FP) Total Test Charges: 12,20,000 (For3 samples of DP) & 15,45,000 (For3 samples of FP)
9.19(Unwanted tripping Behaviour in the case of surge currents)	-	16000	12000 (For 3 Samples of DP) 16000 (For 3 Samples of FP)
9.21(DC components)	-	0	Already covered into the Cl. 9.9
6(Marking)	-	0	-
8.1.1(General)	-	0	-
8.1.2(Mechanism)	-	0	-
9.3(Indelibility of marking)	-	0	-
8.1.3(Clearance and creepage distance (External parts only))	-	0	-
9.15(Trip free mechanism)	-	0	-
9.4(Reliability of screws, current-carrying parts and connections)	-	0	-
9.5(Reliability of terminals for external conductors)	-	0	-
9.6(Protection againts electrci shock)	-	0	-
9.13(Resistance to heat)	-	0	-
8.1.3(Clearance and creepage distance (Internal parts only))	-	0	-
9.25(Resistance to rusting)	-	0	-
9.14(Resistance to abnormal heat and to fire)	-	0	-
9.7.7.4(Resistance of the insulation of open contacts and basic insulation against an impulse voltage in normal conditions)	-	0	-
9.7.7.5(Verification of the behaviour of components bridging the basic insulation)	-	0	-
9.7.1(Resistance to humidity)	-	0	-
9.7.2(Insulation resistance of the main circuit)	-	0	-
9.7.3(Dielectric strength of the main circuit)	-	0	-
9.7.4(Insulation resistance and dielectric strength of auxiliary circuits)	-	0	-
9.7.7.2(Verification of clearances with the impulse withstand voltage)	-	0	-
9.7.5(Secondary circuit of detection transformers)	-	0	-
9.7.6(Capability of control circuits connected to the main circuits etc.)	-	0	-
9.8(Temperature-rise)	-	0	-
9.22.2(Reliability at 40 °C)	-	0	-
9.23(Ageing of electronic components)	-	0	-
9.10(Mechanical and electrical endurance)	-	0	-
9.9(Residual operating characteristics)	-	0	-
9.17(Behaviour in the case of failure of the line voltage)	-	0	-
9.11.2.3a)b)(Perf ormance at IΔm)	-	0	-
9.16(Test device)	-	0	-
9.12(Resistance to mechanical shock and impact)	-	0	-
9.18(Non-operating current under overcurrent conditions)	-	0	-
9.11.2.3c)(Verification of the suitability of RCCBs for use in IT-systems)	-	0	-
9.11.2.4 a)(Coordination at Inc)	-	0	-
9.11.2.4 c)(Performance at Im)	-	0	-
9.11.2.4 b)(Coordination at Im)	-	0	-
9.11.2.2(Coordination at IΔc)	-	0	-
9.22.1(Reliability (climatic test))	-	0	-
IEC 61543, Table 5 –T2.3(Surges)	-	0	-
IEC 61543, Table 5 -T2.1(Conducted s ine-wave form voltages or c urrents)	-	0	-
IEC 61543, Table 5 -T2.1(Conducted s ine-wave form voltages or c urrents)	-	0	-
IEC 61543, Table 5 -T2.5(Radiated electromagnetic field)	-	0	-
IEC 61543, Table 5 -T2.2(Fast transients (bursts))	-	0	-
IEC 61543, Table 5 – T2.6(Conducted common mode disturbances in the frequency range lower than 150 kHz)	-	0	-
IEC 61543, Table 6 -T3.1(Electrostatic discharges)	-	0	-
9.19(Unwanted tripping Behaviour in the case of surge currents)	-	0	-

12 May, 2027

-
Included w.e.f. 27.01.2025 Exclusion:IEC 615432 , Table 4 -T1.1 (Harmonics, inter harmonics), IEC 61543, Table 4 -T1.2 (Signalling voltages), 9.21 (DC components).

IS/IEC 60947 : Part 5 : Sec 2 (2019)

LLow-Voltage Switchgear and Controlgear Part 5 Control Circuit Devices and Switching Elements Section 2 Proximity Switches ( First Revision )

1559000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	0	No test
5.2(Operating conditions)	-	0	No test
6.2(Marking)	-	2000	Visual inspection For 1 Samples)
5.3(Rated and limiting values for the proximity switch and switching element(s))	-	0	No test
6.4(Environmental information)	-	0	No test
7(Normal service, mounting and transport conditions)	-	0	No test
8(Constructional and performance requirements)	-	1559000	Full tests as per Seq. 1 to Seq. 5 tests and CL. 9.2, 9.3 Annex B & Annex C are covered in this general clause
8.1.1.2(Glow-wire testing)	-	30000	For 1 Sample
8.1.1.3(Test based on flammability categor)	-	60000	For 1 Sample
8.1.2(Current-carrying parts and their connections)	-	0	no tests
8.1.3(Clearances and creepage distances)	-	17000	For 1 Sample
8.1.7.1(Constructional requirements)	-	80000	For 1 Sample
8.1.9(Provisions for protective earthing)	-	3000	For 1 Sample
8.1.10(Degree of protection)	-	60000	For 1 Sample
8.1.11(Requirements for proximity switches with integrally connected cables)	-	25000	For 1 Sample
8.1.15(Protection against artificial optical radiation)	-	7000	For 1 Sample
8.2(Performance requirements)	-	1559000	Full tests as per Seq. 1 to Seq. 5 tests and CL. 9.2, 9.3 Annex B & Annex C are covered in this general clause
8.2.2(Temperature-rise)	-	15000	For 1 Sample
8.2.3(Dielectric properties)	-	15000	For 1 Sample
8.2.3.2(Impulse withstand voltage)	-	10000	For 1 Sample
8.2.4(Ability to make and break under normal load and abnormal load conditions)	-	60000	For 1 Sample
8.2.5(Conditional short-circuit current)	-	45000	For 1 Sample
8.2.6(Electromagnetic compatibility (EMC))	-	520000	For all EMC tests for 1 sample
8.2.6.2(Immunity)	-	0	Covered under above test
8.2.6.2.2(Electrostatic discharges)	-	40000	For 1 sample
8.2.6.2.3(Radiated radio-frequency electromagnetic fields)	-	160000	For 1 sample
8.2.6.2.4(Electrical fast transients/bursts)	-	40000	For 1 sample
8.2.6.2.5(Surges)	-	0	Test not applicable for these products
8.2.6.2.6(Conducted disturbances induced by radio-frequency fields)	-	40000	For 1 sample
8.2.6.2.7(Power-frequency magnetic fields)	-	40000	For 1 sample
8.2.6.2.8(Voltage dips and interruptions)	-	60000	For 1 sample
8.2.6.3(Emission)	-	140000	For 1 sample for Conducted Emission Test & Radiated Emission Test
8.3(Physical dimensions)	-	0	No test
8.4(Shock and vibration and special environmental conditions)	-	215000	For 1 sample
9.2(Compliance with constructional requirements)	-	230000	(IP, Mech. & Elect. Properties of terminals, Glow wire, Flammability) for 1 sample
9.2.2.1(Test of resistance to abnormal heat and fire)	-	30000	for 1 sample
9.2.2.1.2(Flammability, hot wire ignition and arc ignition tests (on materials))	-	60000	for 1 sample
9.3.3.4(Dielectric properties)	-	15000	for 1 sample
9.3.3.4.5(Impulse withstand voltage test)	-	10000	for 1 sample
9.3.3.5(Making and breaking capacities)	-	60000	for 1 sample
9.6(Verification of the electromagnetic compatibility)	-	520000	For all EMC tests for 1 sample
B.9.1.2.3(Cable tests)	-	25000	For all as per annex c. for 1 sample
B.9.1.2.4(Change of temperature test)	-	45000	for 1 sample
B.9.1.2.5(Impact test)	-	5000	for 1 sample
B.9.1.2.6(Damp heat, cyclic test)	-	70000	for 1 sample
B.9.1.2.7(Dielectric test after stresses)	-	5000	for 1 sample
C.9.1.2(Pull test)	-	10000	for 1 sample
C.9.1.3(Torque test)	-	5000	for 1 sample
C.9.1.4(Push test)	-	5000	for 1 sample
C.9.1.5(Bend test)	-	5000	for 1 sample
9.3.4(Performance under short-circuit current conditions)	-	45000	for 1 sample
9.4(Testing of operating distances)	-	15000	for 1 sample
9.5(Testing for the frequency of operating cycles)	-	15000	for 1 sample
8.1.10(Degree of protection)	-	60000	for 1 sample
9.3.3.2(Operating limits)	-	5000	for 1 sample
5.1(General)	-	0	Duplicate clause, already considered
5.2(Operating conditions)	-	0	Duplicate clause, already considered
6.2(Marking)	-	0	Duplicate clause, already considered
5.3(Rated and limiting values for the proximity switch and switching element(s))	-	0	Duplicate clause, already considered
6.4(Environmental information)	-	0	Duplicate clause, already considered
7(Normal service, mounting and transport conditions)	-	0	Duplicate clause, already considered
8(Constructional and performance requirements)	-	0	Duplicate clause, already considered
8.1.1.2(Glow-wire testing)	-	0	Duplicate clause, already considered
8.1.1.3(Test based on flammability categor)	-	0	Duplicate clause, already considered
8.1.2(Current-carrying parts and their connections)	-	0	Duplicate clause, already considered
8.1.3(Clearances and creepage distances)	-	0	Duplicate clause, already considered
8.1.7.1(Constructional requirements)	-	0	Duplicate clause, already considered
8.1.9(Provisions for protective earthing)	-	0	Duplicate clause, already considered
8.1.10(Degree of protection)	-	0	Duplicate clause, already considered
8.1.11(Requirements for proximity switches with integrally connected cables)	-	0	Duplicate clause, already considered
8.1.15(Protection against artificial optical radiation)	-	0	Duplicate clause, already considered
8.2(Performance requirements)	-	0	Duplicate clause, already considered
8.2.2(Temperature-rise)	-	0	Duplicate clause, already considered
8.2.3(Dielectric properties)	-	0	Duplicate clause, already considered
8.2.3.2(Impulse withstand voltage)	-	0	Duplicate clause, already considered
8.2.4(Ability to make and break under normal load and abnormal load conditions)	-	0	Duplicate clause, already considered
8.2.5(Conditional short-circuit current)	-	0	Duplicate clause, already considered
8.2.6(Electromagnetic compatibility (EMC))	-	0	Duplicate clause, already considered
8.2.6.2(Immunity)	-	0	Duplicate clause, already considered
8.2.6.2.2(Electrostatic discharges)	-	0	Duplicate clause, already considered
8.2.6.2.3(Radiated radio-frequency electromagnetic fields)	-	0	Duplicate clause, already considered
8.2.6.2.4(Electrical fast transients/bursts)	-	0	Duplicate clause, already considered
8.2.6.2.5(Surges)	-	0	Duplicate clause, already considered
8.2.6.2.6(Conducted disturbances induced by radio-frequency fields)	-	0	Duplicate clause, already considered
8.2.6.2.7(Power-frequency magnetic fields)	-	0	Duplicate clause, already considered
8.2.6.2.8(Voltage dips and interruptions)	-	0	Duplicate clause, already considered
8.2.6.3(Emission)	-	0	Duplicate clause, already considered
8.3(Physical dimensions)	-	0	Duplicate clause, already considered
8.4(Shock and vibration and special environmental conditions)	-	0	Duplicate clause, already considered
9.2(Compliance with constructional requirements)	-	0	Duplicate clause, already considered
9.2.2.1(Test of resistance to abnormal heat and fire)	-	0	Duplicate clause, already considered
9.2.2.1.2(Flammability, hot wire ignition and arc ignition tests (on materials))	-	0	Duplicate clause, already considered
9.3.3.4(Dielectric properties)	-	0	Duplicate clause, already considered
9.3.3.4.5(Impulse withstand voltage test)	-	0	Duplicate clause, already considered
9.3.3.5(Making and breaking capacities)	-	0	Duplicate clause, already considered
9.6(Verification of the electromagnetic compatibility)	-	0	Duplicate clause, already considered
B.9.1.2.3(Cable tests)	-	0	Duplicate clause, already considered
B.9.1.2.4(Change of temperature test)	-	0	Duplicate clause, already considered
B.9.1.2.5(Impact test)	-	0	Duplicate clause, already considered
B.9.1.2.6(Damp heat, cyclic test)	-	0	Duplicate clause, already considered
B.9.1.2.7(Dielectric test after stresses)	-	0	Duplicate clause, already considered
C.9.1.2(Pull test)	-	0	Duplicate clause, already considered
C.9.1.3(Torque test)	-	0	Duplicate clause, already considered
C.9.1.4(Push test)	-	0	Duplicate clause, already considered
C.9.1.5(Bend test)	-	0	Duplicate clause, already considered
9.3.4(Performance under short-circuit current conditions)	-	0	Duplicate clause, already considered
9.4(Testing of operating distances)	-	0	Duplicate clause, already considered
9.5(Testing for the frequency of operating cycles)	-	0	Duplicate clause, already considered
8.1.10(Degree of protection)	-	0	Duplicate clause, already considered
9.3.3.2(Operating limits)	-	0	Duplicate clause, already considered
9.3.3.3(Temperature-rise)	-	15000	For 1 sample
5.1(General)	-	0	-
5.2(Operating conditions)	-	0	-
6.2(Marking)	-	0	-
5.3(Rated and limiting values for the proximity switch and switching element(s))	-	0	-
6.4(Environmental information)	-	0	-
7(Normal service, mounting and transport conditions)	-	0	-
8(Constructional and performance requirements)	-	0	-
8.1.1.2(Glow-wire testing)	-	0	-
8.1.1.3(Test based on flammability categor)	-	0	-
8.1.2(Current-carrying parts and their connections)	-	0	-
8.1.3(Clearances and creepage distances)	-	0	-
8.1.7.1(Constructional requirements)	-	0	-
8.1.9(Provisions for protective earthing)	-	0	-
8.1.10(Degree of protection)	-	0	-
8.1.11(Requirements for proximity switches with integrally connected cables)	-	0	-
8.1.15(Protection against artificial optical radiation)	-	0	-
8.2(Performance requirements)	-	0	-
8.2.2(Temperature-rise)	-	0	-
8.2.3(Dielectric properties)	-	0	-
8.2.3.2(Impulse withstand voltage)	-	0	-
8.2.4(Ability to make and break under normal load and abnormal load conditions)	-	0	-
8.2.5(Conditional short-circuit current)	-	0	-
8.2.6(Electromagnetic compatibility (EMC))	-	0	-
8.2.6.2(Immunity)	-	0	-
8.2.6.2.2(Electrostatic discharges)	-	0	-
8.2.6.2.3(Radiated radio-frequency electromagnetic fields)	-	0	-
8.2.6.2.4(Electrical fast transients/bursts)	-	0	-
8.2.6.2.5(Surges)	-	0	-
8.2.6.2.6(Conducted disturbances induced by radio-frequency fields)	-	0	-
8.2.6.2.7(Power-frequency magnetic fields)	-	0	-
8.2.6.2.8(Voltage dips and interruptions)	-	0	-
8.2.6.3(Emission)	-	0	-
8.3(Physical dimensions)	-	0	-
8.4(Shock and vibration and special environmental conditions)	-	0	-
9.2(Compliance with constructional requirements)	-	0	-
9.2.2.1(Test of resistance to abnormal heat and fire)	-	0	-
9.2.2.1.2(Flammability, hot wire ignition and arc ignition tests (on materials))	-	0	-
9.3.3.4(Dielectric properties)	-	0	-
9.3.3.4.5(Impulse withstand voltage test)	-	0	-
9.3.3.5(Making and breaking capacities)	-	0	-
9.6(Verification of the electromagnetic compatibility)	-	0	-
B.9.1.2.3(Cable tests)	-	0	-
B.9.1.2.4(Change of temperature test)	-	0	-
B.9.1.2.5(Impact test)	-	0	-
B.9.1.2.6(Damp heat, cyclic test)	-	0	-
B.9.1.2.7(Dielectric test after stresses)	-	0	-
C.9.1.2(Pull test)	-	0	-
C.9.1.3(Torque test)	-	0	-
C.9.1.4(Push test)	-	0	-
C.9.1.5(Bend test)	-	0	-
9.3.4(Performance under short-circuit current conditions)	-	0	-
9.4(Testing of operating distances)	-	0	-
9.5(Testing for the frequency of operating cycles)	-	0	-
8.1.10(Degree of protection)	-	0	-
9.3.3.2(Operating limits)	-	0	-
9.3.3.3(Temperature-rise)	-	0	-

12 May, 2027

-
Included w.e.f. 06.12.2024 Exclusion: 8.1.10 (Degree of protection-IP X9), Annexure E. Product rating: up to 250V AC & 300V DC; At 200mA AC & 50mA DC; Short circuit test at max. 15KA AC,

IS/IEC 60947 : Part 5 : Sec 5 (2016)

Low - Voltage switchgear and controlgear: Part 5 control circuit devices and switching elements: Sec 5 electrical emergency stop devices with mechanical latching function

Electrical emergency stop devices with mechanical latch

1809302 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
A.3.2.3(Electrical durability)	-	144000	Per test per batch of 3 identical samples Considered The numbers of operating cycles as 1 million .
A.3.2.2(Mechanical durability)	-	96000	Per test per batch of 3 identical samples Considered The numbers of operating cycles as 1 million.
5.3(Degrees of protection of enclosed equipment)	-	60000	Per test per batch of 3 identical samples
7.3.2(Robustness of a button actuator)	-	6000	Per test per batch of 3 identical samples
7.3.3(Durability test)	-	12000	Per test per batch of 3 identical samples
7.4(Conditioning procedures)	-	324000	Per test per batch of 3 identical samples
7.5(Shock test)	-	60000	Per test per batch of 3 identical samples
7.6(Vibration tests)	-	120000	Per test per batch of 3 identical samples
7.8.1(Disengagement of wire or rope)	-	18000	Per test per batch of 3 identical samples
5.5(Electrical durability)	-	144000	Per test per batch of 3 identical samples
5.4 (8.3.3.5.3 of IS 60947-5-1)(Test sequence III : Making and breaking capacities of switching elements under abnormal conditions)	-	24000	Per test per batch of 3 identical samples (For both normal (8.3.3.5.2) and abnormal test (8.3.3.5.3))
7.7.1(General)	-	0	cost is considered in 7.7.2
7.7.2(Opening test)	-	6000	Per test per batch of 3 identical samples
7.7.3(Latching test for button-type emergency device)	-	6000	Per test per batch of 3 identical samples
7.7.4(Resetting test)	-	6000	Per test per batch of 3 identical samples
7.7.5(Impact test for button type actuators)	-	6000	Per test per batch of 3 identical samples
5.2 (K.8.3.6 of IS/IEC 60947-5-1 : 2009)(Verification of direct opening action)	-	86000	Per test per batch of 3 identical samples

12 May, 2027

-
Included w.e.f. 09.04.2024 Exclusion: Cl. 5.3 (Degrees of protection of enclosed equipment) Product rating: Up to 10A/600V AC & DC, Short circuit test at max. 15KA AC,

IS/IEC 60947 : Part 2 (2016)

Low - Voltage switchgear and controlgear: Part 2 circuit - Breakers (First Revision)

Circuit breakers

987500 View breakup
Rs.8,33,400/- for SP/SPN/DP, Rs.9,87,500/- For TP/TPN/FP (For 1 set o fsamples for all sequences)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3.3.2(Tripping limits and characteristics)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 TP/TPN/FP-35000
8.3.3.3(Test of dielectric properties)	-	28000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-22400 TP/TPN/FP-28000
8.3.3.4(Mechanical operation and operational performance capability)	-	46000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-42000 TP/TPN/FP-46000
8.3.3.5(Overload performance)	-	50000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-44000 TP/TPN/FP-50000
8.3.3.6(Verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.3.7(Verification of temperature-rise)	-	15000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.3.8(Verification of Overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.3.9(Verification of undervoltage and shunt releases)	-	8000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-8000
8.3.3.10(Verification of main contact position)	-	7000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-5000 TP/TPN/FP-7000
8.3.4.2(Test of service short circuit breaking capacity)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
8.3.4.3(Verification of operational performance capability)	-	20000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-15000 TP/TPN/FP-20000
8.3.4.4(Verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.4.5(Verifiation of temperature-rise)	-	15000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.4.6(verification of overload releases (sequence II))	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.5.2(Verification of Overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.5.3(Rated ultimate short-circuit breaking capacity)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
8.3.5.4(Verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.5.5(verification of overload releases (sequence III))	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.6.2(Verification of Overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.6.3(Rated short-time withstand current)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
8.3.6.4(Verification of temperature-rise)	-	15000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.6.5(Short-circuit breaking capacity at maximum short-time withstand current)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
8.3.6.6(Verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.6.7(Verification of Overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.7.2(Short-circuit at the selectivity limit current)	-	30000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-25000 & 30000 TP/TPN/FP-30000 & 35000
8.3.7.3((stage 1) verification of temperature-rise (sequence V))	-	15000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.7.4(Verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.7.5((stage 2) verification of overload releases (sequence V))	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.7.6(Short-circuit at 1,1 times take-over current)	-	30000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-25000 & 30000 TP/TPN/FP-30000 & 35000
8.3.7.7(Short-circuit at ultimate short-circuit breaking capacity)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
8.3.7.8(Verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.7.9(Verification of Overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.8.2(Verification of Overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
8.3.8.3(Rated short-time withstand current)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
8.3.8.4(Rated service short-circuit breaking capacity*)	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
8.3.8.5(Verification of operational performance capability)	-	20000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-15000 TP/TPN/FP-20000
8.3.8.6(Verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.8.7(Verification of temperature-rise)	-	15000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.8.8(Verification of Overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
C.2(individual pole short circuit breaking capacity (Isu))	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
C.3(verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
C.4(verification of overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000
H.2(individual pole short circuit (IIT))	-	35000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-30000 & 40000 TP/TPN/FP-35000 & 45000
H.3(verification of dielectric withstand)	-	7500	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
H.4(verification of overload releases)	-	13000	Complete Testing charges for SP/SPN/DP -733400 (upto 15kA) and 833400 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-887500 (upto 10kA) and 987500 (above 10kA up to 15kA) SP/SPN/DP-10000 TP/TPN/FP-13000

12 May, 2027

-
Included w.e.f. 24-02-2022. Product rating : Up to 100A/Max. 690V AC, Short circuit test at max. 15KA AC

IS 16046 : Part 1 (2018)

290000 View breakup
Rs.2,90,000/- for Secondary Nickel cells; Rs.2,03,000/- for Secondary Nickel batteries

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Insulation and Wiring)	-	15000	Cell: INR 290,000/- Battery: INR 203,000/-
7.1(Charging procedure for test purposes)	-	30000	Cell: INR 290,000/- Battery: INR 203,000/-
5.3(Venting)	-	2000	Cell: INR 290,000/- Battery: INR 203,000/-
7.2(Intended Use)	-	100000	Cell: INR 290,000/- Battery: INR 203,000/- For clause 7.2.3 (Case stress at high ambient temperature is not applicable for cells - INR 15000/-)
7.3(Reasonably foreseeable misuse)	-	143000	Cell: INR 290,000/- Battery: INR 203,000/-
5.1(General)	-	0	--

12 May, 2027

-
Included w.e.f 13/03/2019

IS/IEC 60898 : PART 1 (2015)

Electrical accessories - Circuit - Breakers for overcurrent protection for household and similar installations: Part 1 circuit - Breakers for a.c. operation (First Revision)

MCB

611940 View breakup
Rs.3,84,740/- For 3 samples of SP, Rs.4,68,440/- For 3 samples of SPN or DP, Rs.5,80,940/- For 3 samples of TP or TPN, Rs.6,11,940/- For 3 samples of FP

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Marking and other product information, IS 60898-1)	-	500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.1(General, IS 60898-1)	-	500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.2(Mechanism, IS 60898-1)	-	500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.3(Test of indelibility of marking, IS 60898-1)	-	800	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.3(Clearances and creepage distances, IS 60898-1)	-	850	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.4(Test of reliability of screws, current-carrying parts and connections, IS 60898-1)	-	3000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.5.1(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	3500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) This is inclusive of 9.5.2-1000, 9.5.3-1250, 9.5.4-1250.
9.6(Test of protection against electric shock, IS 60898-1)	-	1540	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
8.1.3(Clearances and creepage distances, IS 60898-1)	-	850	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.14.3(Test of resistance to heat, IS 60898-1)	-	0	-
9.16(Test of resistance to rusting)	-	1500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.15(Resistance to abnormal heat and to fire)	-	20000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-15000 SPN/DP-15000 TP/TPN-20000 FP-20000
9.7.5.4(Test of protection against electric shock, IS 60898-1)	-	12500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-8000 SPN/DP-10000 TP/TPN-10000 FP-12500
9.7.1(Test of protection against electric shock, IS 60898-1)	-	15000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.7.2(Test of protection against electric shock, IS 60898-1)	-	7500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-5000 TP/TPN-5000 FP-7500
9.7.3(Test of protection against electric shock, IS 60898-1)	-	7500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-5000 TP/TPN-5000 FP-7500
9.7.4(Test of protection against electric shock, IS 60898-1)	-	7500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-5000 TP/TPN-5000 FP-7500
9.7.5.2(Test of protection against electric shock, IS 60898-1)	-	12000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-8000 SPN/DP-10000 TP/TPN-10000 FP-12000
9.8(Test of temperature-rise and measurement of power loss, IS 60898-1)	-	18000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-13000 SPN/DP-15000 TP/TPN-15000 FP-18000
9.9(28- day test, IS 60898-1)	-	30000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-28000 SPN/DP-30000 TP/TPN-30000 FP-30000
9.11(Verification of mechanical and electrical endurance, IS 60898-1)	-	25000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-23000 SPN/DP-23000 TP/TPN-25000 FP-25000
9.12(Short- Circuit tests, IS 60898-1)	-	0	clause 9.12 testing charges are distributed among sub clause which are already updated (9.12.12, 9.12.11.2.2, 9.12.11.2.1, 9.12.11.3, 9.12.11.4.2, 9.12.11.4.3, 9.12.11.4.4)
9.13.1(Mechanical Stress, IS 60898-1)	-	3500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) SP-5000 SPN/DP-6800 TP/TPN-8000 FP-9000
8.1.6(Non-interchangeability)	-	1000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.12.12(Verification of the circuit-breaker after short-circuit tests)	-	37500	This test is repeated 6 times (9.12.11.2.2, 9.12.11.2.1, 9.12.11.3, 9.12.11.4.2, 9.12.11.4.3, 9.12.11.4.4)
9.12.11.2.2(Short-circuit test for verifying the suitability of circuit-breakers for use in IT systems)	-	45800	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 26900/- for SP, SPN, DP 45800/- for TP, TPN, FP
9.5.2(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	0	-
9.5.3(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	0	-
9.5.4(Tests of reliability of screw-type terminals for external copper conductors, IS 60898-1)	-	0	-
9.14.1(Test of resistance to heat, IS 60898-1)	-	1000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) This is inclusive of 9.14.1-300, 9.14.2-350, 9.14.3-350
9.14.2(Test of resistance to heat, IS 60898-1)	-	0	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.10.2(Test of tripping characteristic, IS 60898-1)	-	12000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 7500/- for SP 10000/- for SPN, DP, TP, TPN 12000/- for FP
9.10.3(Test of tripping characteristic, IS 60898-1)	-	12000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 7500/- for SP 10000/- for SPN, DP, TP, TPN 12000/- for FP
9.10.4(Test of tripping characteristic, IS 60898-1)	-	8000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 6000/- for SPN, DP, TP, TPN 8000/- for FP
9.10.5(Test of tripping characteristic, IS 60898-1)	-	14700	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 8300/- for SP 12300/- for SPN, DP, TP, TPN 14700/- for FP
9.13.2.2(Mechanical Stress, IS 60898-1)	-	3500	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 2000/- for SP 2500/- for SPN, DP 3000/- for TP, TPN 3500/- for FP
9.13.2.3(Mechanical Stress, IS 60898-1)	-	200	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.13.2.4(Mechanical Stress, IS 60898-1)	-	1600	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP) 1000/- for SP 1200/- for SPN, DP 1400/- for TP, TPN 1600/- for FP
9.13.2.5(Mechanical Stress, IS 60898-1)	-	200	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.12.11.2.1(Performance at reduced short-circuit currents)	-	57000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.12.11.3(Short-circuit performance at 1 500 A)	-	85000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.12.11.4.2(Service short-circuit capacity (Ics))	-	59000	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.12.11.4.3(Performance at rated short-circuit capacity (Icn))	-	50700	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)
9.12.11.4.4(Performance at rated making and breaking capacity (Icn1) on an individual pole of multipole circuit-breakers)	-	50700	Complete testing charges-384740 (For 3 samples of SP), 462440 (For 3 samples of SPN or DP), 580940 (For 3 samples of TP or TPN) & 611940 (For 3 Samples of FP)

12 May, 2027

-
-

IS/IEC 60947 : Part 5 : Sec 1 (2009)

Low - Voltage switchgear and controlgear: Part 5 control circuit devices and switching elements: Sec 1 electromechanical control circuit devices (First Revision)

Low voltage switchgear and control gear

2431000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3.3.2(Operating limits of contactor relays )	-	15000	For 1 Sample
8.3.3.3(Temperature rise )	-	25000	For 1 Sample
8.3.3.4(Dielectric properties)	-	15000	For 1 Sample
8.3.3.5.2( Making and breaking capacities of switching elements under normal conditions)	-	80000	For 1 Sample
8.3.3.5.5 b)(Dielectric verification)	-	5000	For 1 Sample
8.3.3.5.3(– Making and breaking capacities of switching elements under abnormal conditions )	-	55000	For 1 Sample
8.3.4.1(Performance under conditional short-circuit current)	-	50000	For 1 Sample
8.2.5(Verification of actuation force or moment)	-	5000	For 1 Sample
7.1.3(Measurement of clearances and creepage distances, if applicable)	-	10000	For 1 Sample
8.2.6( Verification of limitation of rotation of a rotary switch)	-	20000	For 1 Sample

12 May, 2027

-
Included w.e.f. 09.04.2024 Exclusion: J.8.5 (Degree of protection for indicating towers), Annex C of IEC 60947-1 (Degree of protection of enclosed control circuit devices) Product rating: Up to 10A/600V AC & DC, Short circuit test at max. 15KA AC,

IS/IEC 60947 : Part 4 : Sec 1 (2012)

Low - Voltage switchgear and controlgear: Part 4 contactors and motor - Starters: Sec 1 electromechanical contactors and motor - Starters (First Revision)

Low-voltage switchgear and control gear

2064566 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.3.3.4 (Dielectric properties )	-	6000	For 1 Sample
9.3.4(Performance under short-circuit conditions)	-	86520	86520 up to 10kA (For 1 Sample) , 112476 up to 15kA (For 1 Sample)
9.3.5(Overload current withstand capability of contactors)	-	72100	72100 up to 1000A (For 1 Sample), 93730 up to 4000A (For 1 samples)
9.1.2, (i) (8.2.4 of IEC 60947-1:2007)(Mechanical properties of terminals)	-	10470	10470 (For 1 Sample)
9.1.2 (j) (Annex C of IEC 60947-1)(verification of degrees of protection of enclosed contactors and starters)	-	40000	40000 (For 1 Sample)

12 May, 2027

-
Included w.e.f. 09.04.2024 Exclusion: Cl.8.1.2.3 (Test based on flammability category), Cl.9.1.2 (j) (Annex C of IEC 60947-1) (verification of degrees of protection of enclosed contactors and starters), Cl.9.1.5.2 (Annex Q of IS/IEC 60947-1) (Special tests) Product rating : Up to 63A/Max. 690V AC, Short circuit test at max. 15KA AC,

IS/IEC 60947 : PART 3 (2012)

Low - Voltage switchgear and controlgear: Part 3 switches, disconnectors, switch disconnectors and fuse - Combination units (First Revision)

Low Voltage Switchgear and Controlgear

446700 View breakup
Rs.3,90,200/- for SP/SPN/DP, Rs.4,46,700/- For TP/TPN/FP (For 1 set o fsamples for all sequences)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3.3.1(Temperature-rise)	-	15000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.3.2(Test of dielectric properties)	-	30000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-22400 TP/TPN/FP-30000
8.3.3.4(Dielectric verification)	-	7500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.3.5(Leakage current)	-	2600	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-1800 TP/TPN/FP-2600
8.3.3.6(Temperature-rise verification)	-	15000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.3.7(Strength of actuator mechanism)	-	1700	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-1700 TP/TPN/FP-1700
8.3.4.1.5(Operational performance test)	-	49500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-45500 TP/TPN/FP-49500
8.3.4.2(Dielectric verification)	-	7500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.4.3(Leakage current)	-	2600	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-1800 TP/TPN/FP-2600
8.3.4.4(Temperature-rise verification)	-	15000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.5.1( Short-time withstand current test)	-	35000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-32000 & 42000 TP/TPN/FP-35000 & 45000
8.3.5.2(Short-circuit making capacity test)	-	35000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-32000 & 42000 TP/TPN/FP-35000 & 45000
8.3.5.3(Dielectric verification)	-	7500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.5.4(Leakage current)	-	2600	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-1800 TP/TPN/FP-2600
8.3.5.5(Temperature-rise verification)	-	15000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.6.2, 1 a)(Fuse protected short-circuit withstand)	-	35000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-32000 & 42000 TP/TPN/FP-35000 & 45000
8.3.6.2, 1 a)(Fuse protected short-circuit withstand)	-	35000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-32000 & 42000 TP/TPN/FP-35000 & 45000
8.3.6.3(Dielectric verification)	-	7500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.6.4(Leakage current)	-	2600	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-1800 TP/TPN/FP-2600
8.3.6.5(Temperature-rise verification)	-	15000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.7.1(Overload test)	-	8500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-7500 TP/TPN/FP-8500
8.3.7.2(Dielectric verification)	-	7500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-6000 TP/TPN/FP-7500
8.3.7.3(Leakage current)	-	2600	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-1800 TP/TPN/FP-2600
8.3.7.4(Temperature-rise verification)	-	15000	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-12000 TP/TPN/FP-15000
8.3.3.1(Temperature-rise)	-	0	-
8.3.3.2(Test of dielectric properties)	-	0	-
8.3.3.4(Dielectric verification)	-	0	-
8.3.3.5(Leakage current)	-	0	-
8.3.3.6(Temperature-rise verification)	-	0	-
8.3.3.7(Strength of actuator mechanism)	-	0	-
8.3.4.1.5(Operational performance test)	-	0	-
8.3.4.2(Dielectric verification)	-	0	-
8.3.4.3(Leakage current)	-	0	-
8.3.4.4(Temperature-rise verification)	-	0	-
8.3.5.1( Short-time withstand current test)	-	0	-
8.3.5.2(Short-circuit making capacity test)	-	0	-
8.3.5.3(Dielectric verification)	-	0	-
8.3.5.4(Leakage current)	-	0	-
8.3.5.5(Temperature-rise verification)	-	0	-
8.3.6.2, 1 a)(Fuse protected short-circuit withstand)	-	0	-
8.3.6.2, 1 a)(Fuse protected short-circuit withstand)	-	0	-
8.3.6.3(Dielectric verification)	-	0	-
8.3.6.4(Leakage current)	-	0	-
8.3.6.5(Temperature-rise verification)	-	0	-
8.3.7.1(Overload test)	-	0	-
8.3.7.2(Dielectric verification)	-	0	-
8.3.7.3(Leakage current)	-	0	-
8.3.7.4(Temperature-rise verification)	-	0	-
8.3.3.3(Making and breaking capacities)	-	46500	Complete Testing charges for SP/SPN/DP -358200 (upto 10kA) and 398200 (above 10kA up to 15kA) Complete Testing charges for TP/TPN/FP-416700 (upto 10kA) and 456700 (above 10kA up to 15kA) SP/SPN/DP-42100 TP/TPN/FP-46500

12 May, 2027

-
Included w.e.f. 24-02-2022. Product rating : Up to 63A/Max. 690V AC, Short circuit test at max. 15KA AC,

IS 16333 : Part 3 (2022)

Mobile phone handsets: Part 3 Indian language support for mobile phone handsets - Specific requirements(Second Revision)

31350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Inputting of text)	-	15000	-
5.2(Message Readability)	-	15000	-
5.1(Inputting of text)	-	0	-
5.2(Message Readability)	-	0	-
6(Marking)	-	1350	-

12 May, 2027

-
Included w.e.f. 25-08-2022

IS 16221 : Part 2 (2015)

Safety of power converters for use in photovoltaic power systems: Part 2 particular requirements for inverters

1585946 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and documentation)	-	7500	-
7(Protection against electric shock and energy hazards)	-	178000	-
8(Protection against Mechanical Hazards)	-	53500	-
9(Protection against Fire Hazards)	-	600000	-
10(Protection against Sonic Pressure Hazards)	-	47111	-
13(Physical Requirements)	-	132000	-
4.4.4.15.1(Fault-tolerance of residual current monitoring)	-	10000	-
4.4.4.15.2(Fault-tolerance of automatic disconnecting means)	-	10000	-
4.4.4.16(Stand-alone inverters – Load transfer test)	-	40000	-
4.4.4.17(Cooling system failure – Blanketing test)	-	40500	-
4.7.3(Measurement requirements for AC output ports for stand-alone inverters)	-	10000	-
4.7.4(Stand-alone Inverter AC output voltage and frequency)	-	10000	-
4.7.4.2(Steady state output voltage at nominal DC input)	-	10000	-
4.7.4.3(Steady state output voltage across the DC input range)	-	10000	-
4.7.4.4(Load step response of the output voltage at nominal DC input)	-	10000	-
4.7.4.5(Steady state output frequency)	-	10000	-
4.7.5(Stand-alone inverter output voltage waveform)	-	10000	-
4.7.5.2(Sinusoidal output voltage waveform requirements)	-	10000	-
4.7.5.3(Non-sinusoidal output waveform requirements)	-	10000	-
4.7.5.5(Output voltage waveform requirements for inverters for dedicated loads)	-	10000	-
4.8.2.1(Array insulation resistance detection for inverters for ungrounded arrays)	-	23750	-
4.8.2.2(Array insulation resistance detection for inverters for functionally grounded arrays)	-	23750	-
4.8.3.2(30 mA touch current type test for isolated inverters)	-	32835	-
4,8.3.3(Fire hazard residual current type test for isolated inverters)	-	45000	-
4.8.3.5(Protection by residual current monitoring)	-	100000	-
7.3.10(Additional requirements for stand-alone inverters)	-	15000	-
9.3.4(Inverter backfeed current onto the array)	-	60000	-
13.9(Fault indication)	-	3000	-
14(Components)	-	64000	-

12 May, 2027

-
Excluding following tests – UV exposure (Cl.6.4), Thermal index or capability (Cl.13.6.1.1), Resistance to arcing (Cl.13.6.3.1), UV resistance (Cl.13.6.4), Batteries (Cl.14.8).

IS 16221 : Part 1 (2016)

Safety of Power Converters for use in Photovoltaic Power Systems Part 1 General Requirements

1400612 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.5(Humidity preconditioning)	-	30000	-
4.6(Backfeed voltage protection)	-	5000	-
4.7(Electrical rating tests)	-	30000	-
7(Protection against electric shock and energy hazards)	-	118834	-
12(Chemical hazards)	-	5000	-
4.3, 4.3.2, 4.3.2.2, 4.3.2.3(Thermal Tests (Maximum temperatures, Touch temperature, temperature limits for mount surfaces))	-	60000	-
4.4.3.1(Protection against shock hazard)	-	5000	-
4.4.3.2(Protection against spread of fire)	-	5000	-
4.4.3.4(Protection Against parts expulsion hazards)	-	5000	-
4.4.4.1(Component fault tests)	-	130000	-
4.4.4.2(Equipment’s or parts for short-term or intermittent operation)	-	3000	-
4.4.4.3(Motors(Lock rotor))	-	5000	-
4.4.4.4(Transformer short circuit tests)	-	5000	-
4.4.4.5(Output short circuit)	-	5000	-
4.4.4.6(Backfeed current test for equipment with more than one source of supply)	-	52835	-
4.4.4.7(Output overload)	-	8555	-
4.4.4.8(Cooling system failure)	-	15000	-
4.4.4.9(Heating devices)	-	2000	-
4.4.4.10(Safety interlock systems)	-	2000	-
4.4.4.11(Reverse d.c. connections)	-	6500	-
4.4.4.12(Voltage selector mismatch)	-	2000	-
4.4.4.13(Mis-wiring with incorrect phase sequence or polarity)	-	6500	-
4.4.4.14(Printed wiring board short-circuit test)	-	3000	-
4.6.1(Backfeed tests under normal conditions)	-	52835	-
4.6.2(Backfeed tests under single-fault conditions)	-	52835	-
5.1.2(Durability of markings)	-	1000	-
5.2.1(Visibility and legibility requirements for warning markings)	-	2569	-
6.3(Ingress protection)	-	35000	-
7.3.2.3(Short-term limits of accessible voltages under fault conditions)	-	10000	-
7.3.2.6(Working voltage and DVC)	-	22835	-
7.3.4,7.3.4.2(protection against direct contact)	-	3417	-
7.3.4.3(Protection by means of insulation of live parts)	-	4000	-
7.3.5,7.3.5.2(Protection in case of direct contact)	-	3000	-
7.3.5.3.1(Limitation of current through protective impedance)	-	3000	-
7.3.5.3.2(Limitation of discharging energy through protective impedance)	-	3000	-
7.3.5.4(Protection by means of limited voltages)	-	3000	-
7.3.6.1,7.3.6.2(Protection against indirect contact(Creapage & clearance))	-	12000	-
7.3.6.3(Protective class I - Protective bonding and earthing)	-	12834	-
7.3.6.3.3(Rating of protective bonding)	-	8000	-
7.3.7.8.4.2(Use of coating materials (on PWBs))	-	48000	-
7.3.7.4(Clearance distances)	-	35000	-
7.3.7.5(Creepage distances)	-	32000	-
7.3.8(Residual current detection (RCD) or Monitoring (RCM) device compatibilty (DC components on AC side))	-	1000	-
7.3.9(Protection against shock hazard due to stored energy)	-	8000	-
7.4(Protection against energy hazards)	-	8418	-
7.5.1(Impulse voltage test (type test))	-	47111	-
7.5.2(Voltage test (dielectric strength test))	-	20000	-
7.5.2.3(Humidity preconditioning)	-	45670	-
7.5.3(Partial discharge test (type test or sample test))	-	1000	-
7.5.4(Touch current measurement)	-	32834	-
8.2(Moving parts)	-	1000	-
8.3(Stability)	-	25000	-
8.4(Provisions for lifting and carrying)	-	3000	-
8.5(Wall mounting)	-	23555	-
9.1.1(Reducing the risk of ignition and spread of flame)	-	2000	-
9.1.2(Conditions for a fire enclosure)	-	5000	-
9.1.3(Material requirements for protection against fire hazard)	-	5000	-
9.1.4(Openings in fire enclosures)	-	5000	-
9.1.4.6(Additional requirements for openings in transportable equipment)	-	5000	-
9.2.2(Limited power source tests)	-	79946	-
9.3(Short-circuit and overcurrent protection)	-	60000	-
10.2(Sonic pressure and sound level)	-	47111	-
11.1(Liquid containment, pressure and leakage)	-	6000	-
13.1(Handles and manual controls)	-	1000	-
13.1.1(Adjustable controls)	-	1000	-
13.2(Securing of parts)	-	2000	-
13.3(Provisions for external connections)	-	6000	-
13.4(Internal wiring and connections)	-	2000	-
13.5(Openings in enclosures)	-	2418	-
13.3.2.5(Cord anchorages and strain relief)	-	15000	-
13.3.5(Wire bending space for wires 10mm2 and greater)	-	2000	-
13.5(Openings in enclosures)	-	0	-
13.6.2.1(Stress relief test)	-	15000	-
13.7(Mechanical resistance to deflection, impact, or drop)	-	30000	-
13.8(Thickness requirements for metal enclosures)	-	5000	-
14.2(Motor over-temperature protection)	-	2000	-
14.3(Over-temperature protection devices)	-	2000	-
14.7(Circuits or components used as transient overvoltage limiting devices)	-	10000	-
8.6(Expelled parts)	-	1000	-
11.2(Fluid pressure and leakage)	-	8000	-
14.6(Printed circuit boards)	-	10000	-

12 May, 2027

-
Excluding following tests – UV exposure (Cl.6.4), Thermal index or capability (Cl.13.6.1.1), Resistance to arcing (Cl.13.6.3.1), UV resistance (Cl.13.6.4), Batteries (Cl.14.8).

IS 616 (2017)

Audio, video and similar electronic apparatus - Safety requirements (Fifth Revision)

single phase Test bench capacity AC Source -3.7KVA

180000 View breakup
• Rs.1,31,000/- For Plasma/LCD/LED TVs (less than 32”) • Rs.1,80,000/- For Optical disc player with built in amplifier (Min. 200W) • Rs.1,80,000/- For Amplifier with output power (Min. 2kW) • Rs.1,80,000/- For Electronic musical systems (Min. 200W) • Rs.1,80,000/- For Electronic video games • Rs.1,80,000/- For Power adapter for audio, video and similar electronic apparatus • Rs.1,80,000/- For Plasma/LCD/LED TVs (Min. 32'') • Rs.86,000/- For Wireless headphones and earphones • Rs.180000/- For Electronic Musical System with input power below 200W • Rs.1,80,000/- For Television other than Plasma/ LCD/LED TV’s • Rs.96,000/- for Wireless Microphone, Webcam (finished products) • Rs.1,80,000/- for Video Camera Smart Speakers (with and without display) Bluetooth Speakers

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Marking and instructions)	-	2000	NA
7(Heating under normal operating conditions)	-	17000	NA
8(Constructional requirements with regard to the protection against electric shock)	-	8000	NA
9(Electric shock hazard under normal operating conditions)	-	18000	NA
11(Fault conditions)	-	15000	NA
12(Mechanical strength)	-	14000	NA
13(CLEARANCES and CREEPAGE DISTANCES)	-	12000	NA
15(TERMINALS)	-	8000	NA
16(External flexible cords)	-	5000	NA
17(Electrical connections and mechanical fixings)	-	5000	NA
19(Stability and mechanical hazards)	-	12000	NA
20(Resistance to fire)	-	18000	NA
Annex-A(Additional requirements for apparatus with protection against splashing water)	-	24000	NA
Annex-B(Apparatus to be connected to the TELECOMMUNICATION NETWORKS)	-	22000	NA

12 May, 2027

-
REVISED VERSION W.E.F. 16-12-2019. INCLUDED IS 616:2017. Excluding following tests: Components (Cl.14), Ionization radiation (Cl.6.1), Remote control devices held in hand (cl.12.3); Mechanical strength of picture tube and protection against the effect of implosion (cl.18); Viket softening test (cl.7.2)

IS 16169 (2019)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures (First Revision)

Solar Inverters

350000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6(Test for single or multi-phase inverter)	-	350000		-

12 May, 2027

-
Included w.e.f. 6-4-2021

IS/IEC 61730 : PART 2 (2004)

Photovoltaic (PV) Module Safety Qualification Part 2 Requirements for Testing

CRYSTALLINE SILICON TERRESTRIAL PHOTOVOLTAIC (PV) MODUL

1250000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Visual Inspection (MST 01))	-	2000	-
10.2(Accessibility test (MST 11))	-	4000	-
10.3(Cut susceptibility test (MST 12))	-	4000	-
10.4(Ground Continuity Test (MST 13))	-	4000	-
10.5(Impulse voltage test (MST 14))	-	20000	-
10.6(Dielectric withstand test (MST 16))	-	5000	-
10.7(Temperature test (MST 21))	-	10000	-
10.8(Fire test (MST 23))	-	50000	-
10.9(Reverse Current overload test (MST 26))	-	10000	-
10.10(Module breakage test (MST 32))	-	10000	-
11.1(Partial discharge-test (MST 15))	-	15000	-
Cl.5, Table 7(Hot spot test (MST 22))	-	15000	-
Cl.5, Table 7(UV resistance (MST 54))	-	35000	-
Cl.5, Table 7(Humidity freeze (10HF) (MST 52))	-	150000	-
Cl.5, Table 7(Damp heat (DH1000) (MST 53))	-	230000	-
Cl.5, Table 7(Wet leakage current test (MST 17))	-	7000	-
Cl.5, Table 7(Robustness of termination test (MST 42))	-	5000	-
Cl.5, Table 7(Mechanical load test (MST 34))	-	10000	-
Cl.5, Table 7(Thermal cycling (T200) (MST 51))	-	230000	-
Cl.5, Table 7(Thermal cycling (T50) (MST 51))	-	24000	-

12 May, 2027

-
Fire test as per cl.10.8 included w.e.f. 13.03.2019 10% discount to BIS

IS/IEC 61730 : PART 1 (2004)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction

PV Modules

100000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Polymeric materials)	-	10000	-
6(Internal wiring and current-carrying parts)	-	10000	-
7(Connections)	-	10000	-
8(Bonding and grounding)	-	10000	-
9(Creepage and clearance distances)	-	50000	-
10(Field wiring compartments with covers)	-	10000	-

12 May, 2027

-
-

IS/IEC 61730 : PART 1 (2016)

Photovoltaic (PV) Module Safety Qualification Part 1 Requirements for Construction ( First Revision )

PV Modules

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6.3 IS/IEC 61730-1(Insulation Coordination)	-	50000		-

12 May, 2027

-
Included w.e.f. 6-4-2021

IS/IEC 61730 : PART 2 (2016)

Photovoltaic (PV) module safety qualification: Part 2 requirements for testing (First Revision)

CRYSTALLINE SILICON TERRESTRIAL PHOTOVOLTAIC (PV) MODUL

1900000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.2 IS/IEC 61730-2( Visual inspection MST01)	-	2500	-
10.3 IS/IEC 61730-2(Performance at STC MST 02)	-	5500	-
10.4 IS/IEC 61730-2(Maximum power determination MST 03)	-	5500	-
10.5 IS/IEC 61730-2(Insulation thickness test MST 04)	-	10000	-
10.6 IS/IEC 61730-2(Durability of marking MST 05)	-	5500	-
10.7 IS/IEC 61730-2(Sharp edge test MST 06)	-	6000	-
10.8 IS/IEC 61730-2(Bypass diode functionality test MST 07)	-	7000	-
10.9 IS/IEC 61730-2(Accessibility test MST 11)	-	15000	-
10.10 IS/IEC 61730-2(Cut susceptibility test MST 12)	-	15000	-
10.11 IS/IEC 61730-2(Continuity test of equipotential bonding MST 13)	-	15000	-
10.12 IS/IEC 61730-2(Impulse voltage test MST 14)	-	70000	-
10.13 IS/IEC 61730-2( Insulation test MST 16)	-	6000	-
10.14 IS/IEC 61730-2( Wet leakage current test MST 17)	-	15000	-
10.15 IS/IEC 61730-2( Temperature test MST 21)	-	35000	-
10.16 IS/IEC 61730-2(Hot-spot endurance test MST 22)	-	25000	-
10.17 IS/IEC 61730-2( Fire test MST 23)	-	250000	-
10.18 IS/IEC 61730-2(Ignitability test MST 24)	-	80000	-
10.19 IS/IEC 61730-2( Bypass diode thermal test MST 25)	-	20000	-
10.20 IS/IEC 61730-2( Reverse current overload test MST 25)	-	15000	-
10.21 IS/IEC 61730-2( Module breakage test MST 32)	-	10000	-
10.22 IS/IEC 61730-2(Screw connections test MST 33)	-	5000	-
10.23 IS/IEC 61730-2( Static Mechanical load test MST 34)	-	20000	-
10.24 IS/IEC 61730-2( Peel test MST 35)	-	100000	-
10.25 IS/IEC 61730-2( Lap shear strength test MST 36)	-	250000	-
10.26 IS/IEC 61730-2(Materials creep test MST 37)	-	350000	-
10.27 IS/IEC 61730-2( Robutness of terminations test MST 42)	-	12000	-
10.28 IS/IEC 61730-2(Thermal cycling test MST 51)	-	400000	-
10.29 IS/IEC 61730-2( Humidity-freeze test MST 52)	-	250000	-
10.30 IS/IEC 61730-2( Damp heat test MST 53)	-	400000	-
10.31 IS/IEC 61730-2(UV test MST 54)	-	200000	-
10.32 IS/IEC 61730-2( Cold conditioning MST 55)	-	40000	-
10.33 IS/IEC 61730-2( Dry heat conditioning MST 56)	-	350000	-

12 May, 2027

-
Included w.e.f. 6-4-2021

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

170000 View breakup
• Rs.70,000/- for Monitors • Rs.70,000/-for Printers & Plotters • Rs.58,500/- for Scanners • Rs.69,000/- for Keyboards • Rs.70,000/- for Automatic data processing machines • Rs.62,000/- for Power adapters for IT equipments • Rs.35,000/- for Mobile phones • Rs.62,000/- for Cash Registers • Rs.67,000/- for Point of sale terminals; Rs.69,000/- for Copying machines/Duplicators • Rs.33,000/- for Smart card readers • Rs.62,000/- for Mail Processing machines/Postage Machines/Franking machines • Rs.61,500/- for Passport readers • Rs.54,000/- for Power banks use in portable applications • Rs.70,000/- for Set top box • Rs.1,70,000/- for Visual Display Units, Video Monitors of Screen Size upto 32" • Rs.1,19,500/- for Cameras/Equipment for CCTV Cameras • Rs.1,00,500/- for USB Driven barcode readers, Barcode scanners, Iris scanners, Optical fingerprint scanners • Rs.1,00,500/- for Smart watches • Rs.64,000/- for USB Type External Solid storage Devices (above 256 GB capacity)- • Rs.64,000/- for USB External Hard Disk Drive • Rs.1,11,500/- for Standalone Switch Mode Power Supplies (SMPS) with output voltage 48 V (max) • Rs.1,50,500/- for Automatic Teller Cash dispensing machines • Rs.87,000/- for Digital Camera

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(Protection from electric shock and energy hazards)	-	1000	NA
2.2(SELV circuits)	-	2000	NA
2.3(TNV circuits)	-	5000	NA
2.5(Limited power sources .)	-	3000	NA
2.8(Safety interlocks)	-	3000	NA
2.10(Clearances, creepage distances and distances through insulation)	-	3000	NA
3.3(Wiring terminals for connection of external conductors)	-	1000	NA
4.1(Stability)	-	1000	NA
4.4(Protection against hazardous moving parts)	-	500	NA
4.5(Thermal requirements)	-	3000	NA
4.7(Resistance to fire)	-	4000	NA
5.1(Touch current and protective conductor curren)	-	3000	NA
5.2(Electric strength)	-	3000	NA
5.3(Abnormal operating and fault conditions)	-	5000	NA
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	3000	NA
6.3(Protection of the telecommunication wiring system from overheating)	-	3500	NA
1.6(Power interface .)	-	10000	NA
1.7(Markings and instructions)	-	1000	NA
4.2(Mechanical strength)	-	18000	NA
2.6(Provisions for earthing and bonding)	-	2000	NA

12 May, 2027

-
Excluding following tests: Ionizing radiations (cl.4.3.13.2); Effect of UV radiations on materials (cl.4.3.13.3); Human exposure to UV radiations (cl.4.3.13.4); Components (cl.1.5); Power supply cords (cl.3.2.5, 3.2.5.1); Cathode ray tube (cl.4.2.8)

Bureau of Indian Standards

The National Standards Body of India

UL INDIA PRIVATE LIMITED

Loc 1&2-Kalyani Platina Campus, Sy. no 129/4, EPIP Zone, Phase II, Whitefield, Bangalore- 560066, Loc3- 30/A, I Stage Vishveshwarya Industrial Estate, Doddanekkundi Industrial Area, Bangalore - 560048, Bangalore, Bengaluru Urban, Karnataka, 560066

9986066622 sarangan.nandakumar@ul.com

Scope List