BIS - LIMS (Laboratory Information Management System)

FOOTWEAR DESIGN & DEVELOPMENT INSTITUTE (FDDI) CHENNAI

Plot No: PB 13, Footwear Component Park, 7th Main Road, Sipcot Industrial Park, Irungattukottai,Sriperumbudur -602117, Chennai, Kanchipuram, Tamil Nadu, 602117

9891994460 rajesh.av@fddiindia.com

Scope List

Reset

4 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

10600 View breakup
-

Clause No.	Exclusion	Remark
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	-
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	-

31 May, 2026

-
-

IS 3735 (1996)

Canvas Shoes, Rubber Sole

10600 View breakup
-

Clause No.	Exclusion	Remark
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	-
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	-
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	-
4.8(Adhesion )	-	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	-
4.1.6.2(Elongation at break after ageing )	-	-
4.1.6.2(Tensile after ageing )	-	-
4.1.6(Compression set )	-	-
4.1.6(Elongation at break )	-	-
4.1.6(Tensile strength)	-	-
4.1.6(Hardness (after accelerated ))	-	-
4.1.6(Flexing resistance test)	-	-
4.1.6(Hardness )	-	-
4.1.6(Relative density)	-	-
4.1.5(Sulpher dyes content )	-	-
4.1.5(Breaking Load )	-	-
4.1.5(Length )	-	-
4.1.4(Thickness)	-	-
4.1.4(Size )	-	-
4.1.3(Color fastness to perspiration)	-	-
4.1.3(Colorfastness to light )	-	-
4.1.3(Single thread breaking load)	-	-
4.1.3(Construction )	-	-
4.1.2(Colorfastness to light )	-	-
4.1.2(Breaking Strength )	-	-
4.1.2(Width )	-	-
4.1.1.1(Colorfastness to light )	-	-
4.1.1 (Drill) (End & Picks/dm)	-	-
4.1.1 (Drill) (Colorfastness to light )	-	-
4.1.1 (canvas )(End & Picks/dm)	-	-
4.1.1 (canvas )(Breaking Load )	-	-

31 May, 2026

-
-

IS 10702 (2023)

Hawai Chappal-Specification

Hawai Chappal

39000 View breakup
-

Clause No.	Exclusion	Remark
5.4(Tear strength )	-	-
5.4(Hardness (shore A)- after ageing)	-	-
5.4(Hardness (Shore A))	-	-
5.4(Breaking strength )	-	-
5.4(Elongation at break )	-	-
5.4(Tensile Strength )	-	-
5.4(Relative density )	-	-
5.4(Shrinkage test (at 100 C temp))	-	-
5.4(Shrinkage test (at room temp))	-	-
5.4(Split tear strength )	-	-
5.4(Compression set)	-	-
5.4(Hardness (Shore A))	-	-
5.4(Relative density)	-	-
5.3(Thickness )	-	-
4.2(Length)	-	-
4.3(Thickness)	-	-
4.4 , Table No. 1 , i)(Density)	-	-
4.4 , Table No. 1 , ii)(2Compression set at constant stress)	-	-
4.4 , Table No. 1 , iii)(3Split tear strength)	-	-
4.4 , Table No. 1 , iv)("Shrinkage at 50 ºC ± 1 ºC for 24 h for polymeric material, Shrinkage at 100 ºC ± 1 ºC for 1 h for rubber")	-	-
4.4 , Table No. 1 , v)(5Abrasion resistance at applied force)	-	-
4.4 , Table No. 1 , vi)(Flexing resistance: Maximum cut growth at 50 000 flexes)	-	-
4.4 , Table No. 1 , vii)(7 Hydrolysis resistance, Maximum cut growth at 50 000 flexes)	-	-
4.4 , Table No . 2 , i)(Density , Solid strap, Cellular strap)	-	-
4.4 , Table No . 2 , ii)("Breaking strength , Strap to strap and Toe portion to strap , Elongation at break")	-	-
4.4 , Table No . 2 , iii)(Minimum cross section of the stud)	-	-
4.4 , Table No . 2 , iv)(Stud bolt)	-	-
4.4 , Table No . 3 , i)(Toe post attachment strength)	-	-
4.4 , Table No . 3 , ii)(Attachment strength of rear strap)	-	-
4.4 , Table No . 3 , iii)(Inter layer bond strength)	-	-
Cl. No.5.1,Table no.1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	-
Cl. No.5.1,Table no.1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl. No.5.1,Table no.1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl. No.5.1,Table no.1 of IS 17011(iv)(Chromium (VI))	-	-
Cl. No.5.1,Table no.1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	-
Cl. No.5.1,Table no.1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	-
Cl. No.5.1,Table no.1 of IS 17011(vii)(Formaldehyde)	-	-
Cl. No.5.1,Table no.1 of IS 17011(viii)(Organotin compounds)	-	-
Cl. No.5.1,Table no.1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	-
Cl. No.5.1,Table no.1 of IS 17011(x)(pH)	-	-
Cl. No.5.1,Table no.1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	-
Clause 4.3 - 4.3.1(Thickness)	-	-
Clause 4.3 - 4.3.2(Thickness)	-	-
Clause 4.4 Table 2 -i) - a("Density, g/cm3 Solid strap ")	-	-
Clause 4.4 Table 2 -i) - b(Density, g/cm3 Cellular strap)	-	-
Clause 4.4 Table 2 -ii) - a - 1("Breaking strength, kgf, Min Strap to strap(Solid Strap)")	-	-
Clause 4.4 Table 2 -ii) - a - 2("Breaking strength, kgf, Min Strap to strap(Cellular Strap)")	-	-
Clause 4.4 Table 2 -ii) - a - 3("Breaking strength, kgf, Min Toe portion to strap(Solid Strap)")	-	-
Clause 4.4 Table 2 -ii) - a - 4("Breaking strength, kgf, Min Toe portion to strap(Cellular Strap)")	-	-
Clause 4.4 Table 2 -ii) - b - 1("Elongation at break, percent (Applicable to strap to strap (V shape) Solid Strap")	-	-
Clause 4.4 Table 2 -ii) - b - 2("Elongation at break, percent (Applicable to strap to strap (V shape) Cellular Strap")	-	-
Clause 4.4 Table 2 -iii) - a("Minimum cross section of the stud, mm, Size 1 to 13 (Adult)")	-	-
Clause 4.4 Table 2 -iii) - b("Minimum cross section of the stud, mm, Size 3 to 13 (Children)")	-	-
Clause 4.4 Table 2 -iv) - a("Stud bolt, mm Diameter/edge to edge length")	-	-
Clause 4.4 Table 2 -iv) - b("Stud bolt, mm Thickness")	-	-
Clause 4.4 Table 3 -i)("Toe post attachment strength, N, Min")	-	-
Clause 4.4 Table 3 -ii)("Attachment strength of rear strap, N, Min")	-	-
Clause 4.4 Table 3 -iii)("Inter layer bond strength, N/mm, Min")	-	-
Clause 4.4 Table 1 -i)(Density, g/cm3, Min)	-	-

31 May, 2026

-
-

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

Sports Footwear

51900 View breakup
-

Clause No.	Exclusion	Remark
3.10(Ross Flex test)	-	-
3.10(Shape retention percent )	-	-
3.10(Collapsing load )	-	-
3.9(Lace abrasion test)	-	-
3.9(Griping Strength of Tags)	-	-
3.9(Colour migration / Colour fastness)	-	-
3.9(Breaking Strength )	-	-
3.8(Heat resistance tester )	-	-
3.8(Compression set )	-	-
3.8(Die-C tear Strength )	-	-
3.8(Elongation at Break )	-	-
3.8(Tensile Strength)	-	-
3.7(Flexing index)	-	-
3.7(Abrasion resistance )	-	-
3.7(Tensile Strength)	-	-
3.6(Ross flexing )	-	-
3.6(Adhesion to mid sole )	-	-
3.6(Abrasion resistance )	-	-
3.6(Die-C tear Strength )	-	-
3.6(Trouser tear strength )	-	-
3.5(Heat resistance tester )	-	-
3.5(Adhesive to sole)	-	-
3.5(Compression set )	-	-
3.5(Die-C tear Strength )	-	-
3.5(Split tear strength )	-	-
3.5(Elongation at Break )	-	-
3.5(Tensile Strength)	-	-
3.4(Colorfastness to light )	-	-
3.4(Colour fastness to crocking )	-	-
3.4(Tear Strength)	-	-
3.4(Elongation at Break )	-	-
3.4(Adhesive Strength )	-	-
3.4(Hydrolysis )	-	-
3.4(Upper flexing resistance )	-	-
3.3.3(Sole /midsole bond strength )	-	-
3.3.2(Upper/outsole bond strength)	-	-
Cl. 3.6,Table 7,IS 3400(Part 17), iv)(Tear strength, kg/cm, Min)	-	-
Cl. 3.7 Table 10, Outsole Materials — Thermo Plastic Urethane (TPU) IS 3400 (Part 1) i)(Tensile strength)	-	-
CL. 3.8 Table 12, Insole Material: Stoble Non-woven, Annex G i)(Trouser tear strength, kg, Min)	-	-
CL. 3.8 Table 12, Cl. 6.12 IS 15298 (part1) ii)(Abrasion resistance, cycles, Min)	-	-
Cl. 3.8, Table 12, Annex F, iv)(Heat resistance, shrinkage linear, percent, Max)	-	-
Cl. 3.11 Table 16 A-3.4 of IS 7554 ii)(Resilience, percent, Min)	-	-
Cl. 3.11 Table 16 A-3.5 of IS 7554 iii)(Moisture resistance, percent, Min)	-	-
Cl. 3.11 Table 16 iv) a)A-3.1 of IS 7554(Initial dry area shape retention, percent, Min)	-	-
Cl. 3.11 Table 16 iv) b) A-3.3 of IS 7554(Area shape retention after 10th collapse, dry, percent, Min)	-	-
Cl. 3.11 Table 16,\ Annex B of IS 7554 v)(Peel strength, N/cm, Min)	-	-
Cl. 3.4,Table 3(Lastometer test, mm, Min)	-	-
Cl. 3.5,Table 6(Vamp and Quarter Liningi) Tear strength, N, Min a) Leather,b) Coated fabric and textile)	-	-
Cl. 3.5 Table 6(Abrasion resistance, No. of cycles, Min,a) Dry – 25 600,b) Wet – 12 800)	-	-
Cl. 3.5 Table 6(Water vapour permeability, mg/(cm2.h), Min)	-	-
Cl. 3.5,Table 6(Water vapour coefficient, mg/cm2, Min)	-	-
Cl. 3.5,Table 6(pH value (for leather lining), Min)	-	-
Cl. 3.5,Table 6(Chromium VI content (for leather lining), mg/kg, Max)	-	-
Cl. 3.6,Table 7(Tear strength, kg/cm, Min)	-	-
Cl. 3.6,Table(Heat resistance, shrinkage linear, percent, Max)	-	-
Cl. 3.7 Table 10(Outsole Materials — Thermo Plastic Urethane (TPU) i) Tensile strength)	-	-
CL. 3.8 Table 12(Insole Material: Stoble Non-woven, Annex G i) Trouser tear strength, kg, Min)	-	-
Cl. 3.8,Table 12(IS 3400 (Part 16) iii) Ross flexing, cycles, Min)	-	-
Cl. 3.8, Table 12 Annex F,(iv) Heat resistance, shrinkage linear, percent, Max)	-	-
Cl. 3.11,Table 16(Counter Material: Thermoplastic, Solvent Activated and Heat Activated Sheets i) First dry collapsing load, hardness, N, Min)	-	-
Cl. 3.11 Table 16(A-3.4 of IS 7554 ii) Resilience, percent, Min)	-	-
Cl. 3.11 Table 16,(Annex B of IS 7554 v) Peel strength, N/cm, Min)	-	-
Cl. 3.11 Table 16(A-3.5 of IS 7554 iii)Moisture resistance, percent, Min)	-	-
Cl. 3.11 Table 16 ,iv)(a)A-3.1 of IS 7554 - Initial dry area shape retention, percent, Min b) A-3.3 of IS 7554 - Area shape retention after 10th collapse, dry, percent, Min)	-	-
Cl No.4.2(Construction)	-	-
4.3.1(Insole)	-	-
4.3.2(Toe spring height)	-	-
4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	-
4.3.4("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	-
4.3.5(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	-
4.3.7(Complete Shoe Flexing)	-	-
4.3.9(Slip Resistance)	-	-
Cl No.4.4 , Table No. 2 , i) , a)(Flexing resistance, Dry condition)	-	-
Cl No.4.4 , Table No. 2 , i) , b)(Flexing resistance, Wet condition)	-	-
Cl No.4.4 , Table No. 2 , ii)(Tear strength (average force), Min, N)	-	-
Cl No.4.4 , Table No. 2 , iii) , a)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Dry: (rubbing) Rating: (Marring and staining) ")	-	-
Cl No.4.4 , Table No. 2 , iii) , b)("Colour fastness rubbing (To and fro) Grey scale rate, Min , Wet: (rubbing) Rating: (Marring and staining)")	-	-
Cl No.4.4 , Table No. 2 , iv) , a)(Water vapour permeability, mg/cm2h, Min)	-	-
Cl No.4.4 , Table No. 2 , iv) , b)(Water vapour coefficient, mg/cm2 , Min)	-	-
Cl No.4.4 , Table No. 2 , v)(Stitch tear strength (double hole), N/mm, Min)	-	-
Cl No.4.4 , Table No. 2 , i)(Breaking strength, N/mm, Min)	-	-
Cl No.4.4 , Table No. 2 , ii)(Elongation at break, percent Min)	-	-
Cl No.4.4 , Table No. 2 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	-
Cl No.4.4 , Table No. 2 , iv) , a)(Flexing resistance, Dry condition)	-	-
Cl No.4.4 , Table No. 2 , iv) , b)(Flexing resistance, ,Wet condition)	-	-
Cl No.4.4 , Table No. 2 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	-
Cl No.4.4 , Table No. 2 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	-
Cl No.4.4 , Table No. 2 , vi)(Hydrolysis resistance)	-	-
Cl No.4.5 , Table No. 3 , i)(Tear strength, N, Min)	-	-
Cl No.4.5 , Table No. 3 , ii)(Abrasion resistance, cycles)	-	-
Cl No.4.5 , Table No. 3 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, Min")	-	-
Cl No.4.5 , Table No. 3 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, Min")	-	-
Cl No.4.5 , Table No. 3 , v) , a)(Water vapour permeability, mg/cm2h, Min)	-	-
Cl No.4.5 , Table No. 3 , v) , b)("Water vapour coefficient, mg/cm2 , Min ")	-	-
Cl No.4.6 , Table No. 4 , i)(Thickness, mm, Min)	-	-
Cl No.4.6 , Table No. 4 , ii)(Flexing index, Min)	-	-
Cl No.4.6 , Table No. 4 , iii)(Abrasion resistance, at 400 cycles)	-	-
Cl No.4.6 , Table No. 4 , iv) , a)(Water Absorption, mg/cm2 , Min)	-	-
Cl No.4.6 , Table No. 4 , iv) , b)(Water Desorption, percent, Min)	-	-
Cl No.4.7, Table No. 5 , i)(Thickness, mm, Min)	-	-
Cl No.4.7, Table No. 5 , ii)(Abrasion resistance, cycles)	-	-
Cl No.4.7, Table No. 5 , iii) , a)(Water Absorption, mg/cm2 , Min)	-	-
Cl No.4.7, Table No. 5 , iii) , b)(Water Desorption, percent, Min)	-	-
Cl No.4.8 , Table No. 6 , i)(Abrasion resistance (Volume loss), mm3 , Max)	-	-
Cl No.4.8 , Table No. 6 , ii)("Flexing resistance Belt Method at 90 diameter Mandrel or Bennewart method, cut growth, Max")	-	-
Cl No.4.8 , Table No. 6 , iii)("Hydrolysis resistance, cut growth after 150 000 flexes, in mm, Max")	-	-
Cl No.4.9 , Table No. 7 , i)(Compression set, percent, Max)	-	-
Cl No.4.9 , Table No. 7 , ii)(Split tear strength, kg/25 mm, Min)	-	-
Cl No.4.9 , Table No. 7 , iii)(Heat shrinkage, percent, Max)	-	-
Cl No.4.10 , Table No. 8 , i)(First dry collapsing load, hardness, N, Min)	-	-
Cl No.4.10 , Table No. 8 , ii)(Resilience, percent, Min)	-	-
Cl No.4.10 , Table No. 8 , iv) , a)(Initial dry area shape retention, percent, Min)	-	-
Cl No.4.10 , Table No. 8 , iv) , b)(Area shape retention after 10th collapse, dry, percent, Min)	-	-
Cl No.4.11 , Table No. 9 , i)(Peel strength, N/mm, Min)	-	-
Cl No.4.11 , Table No. 9 , ii)(Shear strength, kPa , Min)	-	-
Cl No.4.12 , Table No. 10 , i)(Limit of useful extension, percent, Min)	-	-
Cl No.4.13 , Table No. 11 , i)(Breaking strength of lace, N, Min)	-	-
Cl No.4.13 , Table No. 11 , ii)(Lace tag strength, N, Min)	-	-
Cl No.4.13 , Table No. 11 , iii)(Lace to lace abrasion,)	-	-
Cl No.4.13 , Table No. 11 , iv)("Colour fastness to water Gray Scale Rate, Min Rating")	-	-
Cl No.4.13 , Table No. 11 , v)(Strength of Buckle/Ski hook, N, Min)	-	-
Cl No.4.13 , Table No. 11 , vi)(Corrosion resistance)	-	-
Cl No . 4.14, Table no. 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	-
Cl No . 4.14, Table no. 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl No . 4.14, Table no. 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-
Cl No . 4.14, Table no. 1 of IS 17011(iv)(Chromium (VI))	-	-
Cl No . 4.14, Table no. 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	-
Cl No . 4.14, Table no. 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	-
Cl No . 4.14, Table no. 1 of IS 17011(vii)(Formaldehyde)	-	-
Cl No . 4.14, Table no. 1 of IS 17011(viii)(Organotin compounds)	-	-
Cl No . 4.14, Table no. 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	-
Cl No . 4.14, Table no. 1 of IS 17011(x)(pH)	-	-
Cl No . 4.14, Table no. 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	-
Cl No . 4.14, Table no. 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	-
Clause 4.3 - 4.3.3(Upper to Mid Sole/Out Sole Bond Performance)	-	-
Clause 4.3 - 4.3.4(Upper to Composite Sole Bond Performance(Applicable Only When the Sole is Composite))	-	-
Clause 4.3 - 4.3.7(Complete Shoe Flexing)	-	-
Clause 4.5, Table 3 i)(Tear strength)	-	-
Clause 4.4, Table 2 v)-a(Water Vapour Permeability)	-	-
Clause 4.8, Table 6 i)(Abrasion Resistance)	-	-
Clause 4.7, Table 5 i)(Thickness)	-	-
Clause 4.6, Table 4 ii)(Abrasion Resistance)	-	-
Clause 4.9, Table 7 ii)(Split Tear strength)	-	-
Clause 4.9, Table 7 iii)(Heat shrinkage)	-	-
Clause 4.8, Table 6 iii)(Hydrolysis Resistance)	-	-

31 May, 2026

-
-

Bureau of Indian Standards

The National Standards Body of India

FOOTWEAR DESIGN & DEVELOPMENT INSTITUTE (FDDI) CHENNAI

Plot No: PB 13, Footwear Component Park, 7th Main Road, Sipcot Industrial Park, Irungattukottai,Sriperumbudur -602117, Chennai, Kanchipuram, Tamil Nadu, 602117

9891994460 rajesh.av@fddiindia.com

Scope List