BIS - LIMS (Laboratory Information Management System)

ARDM Labs Pvt Ltd

A-80, G. T. KARNAL ROAD INDUSTRIAL AREA, AZADPUR, DELHI, North, Delhi, 110033

9810068016 ardmlabs@gmail.com

Scope List

Reset

41 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 16205 : Part 24 (2017)

Conduit Systems for Cable Management part 24 Particular Requirements Conduit Systems Buried Under Ground

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8 Table 101(Dimensions)	-	500	-
10.4(Bending Test)	-	3000	-
10.2(Compression Test)	-	3000	-
9.1 of IS 16205 (Part 1) : 2017(Construction)	-	500	-
14.0(External Influences)	-	18000	-
15.0(Electromagnetic Compatibility)	-	2000	-
13.1.3(Spread of fire)	-	3000	-
13.1.3.1(Spread of fire)	-	3000	-
10.3(Impact Test)	-	3000	-
7.2(Marking and Documentation)	-	500	-

Complete

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.2(diameter of the socket of cap)	-	1000	full testing as per 7834 part 1& 8 @ 14000
6.1.1(VCM Content Test)	-	8000	full testing as per 7834 part 1& 8 @ 11000
2.2.2 table 1(Laying length)	-	1500	full testing as per 7834 part 1& 8 @ 11000
2.2.2(diameter of the socket of cap)	-	500	full testing as per 7834 part 1& 8 @ 11000
2.1(General)	-	0	FOR FULL TESTING AS PER IS 7834 PART 1 @RS 10000
2.1(General)	-	0	FOR FULL TESTING AS PER IS 7834 PART 1 @RS 10000
2.2(Manufacture)	-	0	-
2.2(Manufacture)	-	0	-

Complete

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.3( inside diameter of the socket)	-	1000	full testing as per 7834 part 1&7 @ 11000
2.2.3(Socket length)	-	1000	full testing as per 7834 part 1&7 @ 11000
6.1.1(VCM Content Test)	-	8000	full testing as per 7834 part 1&7 @ 11000
2.2.2, Table 1(Union Laying Length)	-	1000	full testing as per 7834 part 1&7 @ 11000
2.2.3( inside diameter of the socket)	-	1000	full testing as per 7834 part 1&7 @ 11000
2.1(General)	-	0	FOR FULL TESTING AS PER IS 7834 PART 1 @RS 10000
2.2(Manufacture)	-	0	-
2.2.2 table 1(Laying length)	-	0	-
2.2.2, Table 1(Size)	-	0	-
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 06(50 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Union Laying Length)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.3(Socket length)	-	0	-

Complete

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.3( inside diameter of the socket)	-	1000	full testing as per 7834 part 1&6 @ 11000
2.2.3(Socket length)	-	1000	full testing as per 7834 part 1&6 @ 11000
6.1.1(VCM Content Test)	-	8000	full testing as per 7834 part 1&6 @ 11000
2.2.2, Table 1(Socket Laying Length)	-	1000	full testing as per 7834 part 1&6 @ 11000
2.1(General)	-	0	FOR FULL TESTING AS PER IS 7834 PART 1 @RS 10000
2.1(General)	-	0	-
2.2.3(Socket length)	-	0	-
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 06(50 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 08(75 )	-	0	-
table 1 sl.no: 09(90 )	-	0	-
table 1 sl.no: 10(110 )	-	0	-
table 1 sl.no: 11(125 )	-	0	-
table 1 sl.no: 12(140 )	-	0	-
table 1 sl.no: 13(160 )	-	0	-
table 1 sl.no: 14( 180 )	-	0	-
table 1 sl.no: 15(200 )	-	0	-
table 1 sl.no: 16(225 )	-	0	-
table 1 sl.no: 17(250.0)	-	0	-
table 1 sl.no: 18(280.0)	-	0	-
table 1 sl.no: 19(315.0)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2 table 1(Laying length)	-	0	-
2.2.2, Table 1(Socket Laying Length)	-	0	-

Complete

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.3( inside diameter of the socket)	-	1000	full testing as per 7834 part 1&5 @ 11000
2.2.3(Socket length)	-	1000	full testing as per 7834 part 1&5 @ 11000
6.1.1(VCM Content Test)	-	8000	full testing as per 7834 part 1&5 @ 11000
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	1000	full testing as per 7834 part 1&5 @ 11000
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	1000	full testing as per 7834 part 1&5 @ 11000
2.2.3( inside diameter of the socket)	-	1000	full testing as per 7834 part 1&5 @ 11000
2.2.2 table 1(Laying length)	-	1000	full testing as per 7834 part 1&5 @ 11000
2.1(General)	-	0	FOR FULL TESTING AS PER IS 7834 PART 1 @RS 10000
table 1 sl.no: 01(16 (Z) )	-	0	-
table 1 sl.no: 02(20 (Z) )	-	0	-
table 1 sl.no: 03(25 (Z) )	-	0	-
table 1 sl.no: 04(32 (Z) )	-	0	-
table 1 sl.no: 05(40 (Z) )	-	0	-
table 1 sl.no: 06(50 (Z) )	-	0	-
table 1 sl.no: 07(63 (Z) )	-	0	-
table 1 sl.no: 08(75 (Z) )	-	0	-
table 1 sl.no: 09(90 (Z) )	-	0	-
table 1 sl.no: 10(110 (Z) )	-	0	-
table 1 sl.no: 11(125 (Z) )	-	0	-
table 1 sl.no: 12(140 (Z) )	-	0	-
table 1 sl.no: 13(160(z))	-	0	-
table 1 sl.no: 01(16 (Z1) )	-	0	-
table 1 sl.no: 02(20 (Z1) )	-	0	-
table 1 sl.no: 03(25 (Z1) )	-	0	-
table 1 sl.no: 04(32 (Z1) )	-	0	-
table 1 sl.no: 05(40 (Z1) )	-	0	-
table 1 sl.no: 06(50 (Z1) )	-	0	-
table 1 sl.no: 07(63 (Z1) )	-	0	-
table 1 sl.no: 08(75 (Z1) )	-	0	-
table 1 sl.no: 09(90 (Z) )	-	0	-
table 1 sl.no: 10(110 (Z1) )	-	0	-
table 1 sl.no: 11(125 (Z1) )	-	0	-
table 1 sl.no: 12(140 (Z1) )	-	0	-
table 1 sl.no: 13(160(z1))	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.3(Socket length)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	0	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	0	-

Complete

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.3( inside diameter of the socket)	-	1000	full testing as per 7834 part 1&4 @ 11000
2.2.3(Socket length)	-	1000	full testing as per 7834 part 1&4 @ 11000
6.1.1(VCM Content Test)	-	8000	full testing as per 7834 part 1&4 @ 11000
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	1500	full testing as per 7834 part 1&4 @ 11000
2.2.2, Table 1(Size)	-	500	full testing as per 7834 part 1&4 @ 11000
2.1(General)	-	0	FOR FULL TESTING AS PER IS 7834 PART 1 @RS 10000
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 06(50 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 08(75 )	-	0	-
table 1 sl.no: 09(90 )	-	0	-
table 1 sl.no: 10(110 )	-	0	-
table 1 sl.no: 11(125 )	-	0	-
table 1 sl.no: 12(140 )	-	0	-
table 1 sl.no: 13(160 )	-	0	-
table 1 sl.no: 14( 180 )	-	0	-
table 1 sl.no: 15(200 )	-	0	-
table 1 sl.no: 16(225 )	-	0	-
table 1 sl.no: 17(250.0)	-	0	-
table 1 sl.no: 18(280.0)	-	0	-
table 1 sl.no: 19(315.0)	-	0	-
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(90 ̊ Elbow Laying Length)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-
2.2.3(Socket length)	-	0	-
2.2.2 table 1(Laying length)	-	0	-

Complete

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	1000	full testing as per 7834 part 1&3 @ 11000
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	1500	full testing as per 7834 part 1&3 @ 11000
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	1500	full testing as per 7834 part 1&3 @ 11000
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	1500	full testing as per 7834 part 1&3 @ 11000
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	1500	full testing as per 7834 part 1&3 @ 11000
6.1.1(VCM Content Test)	-	8000	full testing as per 7834 part 1&3 @ 11000
2.2.2 table 1(Laying length)	-	1500	full testing as per 7834 part 1&3 @ 11000

Complete

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2.3( inside diameter of the socket)	-	1000	full testing as per 7834 part 1&2 @ 11000
2.2.3(socket length)	-	1000	full testing as per 7834 part 1&2 @ 11000
2.2.2, Table 1(Size)	-	1000	full testing as per 7834 part 1&2 @ 11000
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	1500	full testing as per 7834 part 1&2 @ 11000
2.2.3(socket length)	-	1500	full testing as per 7834 part 1&2 @ 11000
6.4 PART-1(Short term hydraulic test)	-	5000	full testing as per 7834 part 1&2 @ 11000
6.1.1(VCM Content Test)	-	8000	full testing as per 7834 part 1&2 @ 11000
2.1(General)	-	0	FOR FULL TESTING AS PER IS 7834 PART 1 @RS 10000
2.1(General)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2 table 1(Laying Length)	-	0	-
table 1 sl.no: 01(16 )	-	0	-
table 1 sl.no: 02(20 )	-	0	-
table 1 sl.no: 03(25 )	-	0	-
table 1 sl.no: 04(32 )	-	0	-
table 1 sl.no: 05(40 )	-	0	-
table 1 sl.no: 06(50 )	-	0	-
table 1 sl.no: 07(63 )	-	0	-
table 1 sl.no: 08(75 )	-	0	-
table 1 sl.no: 09(90 )	-	0	-
table 1 sl.no: 10(110 )	-	0	-
table 1 sl.no: 11(125 )	-	0	-
table 1 sl.no: 12(140 )	-	0	-
table 1 sl.no: 13(160 )	-	0	-
table 1 sl.no: 14( 180 )	-	0	-
table 1 sl.no: 15(200 )	-	0	-
table 1 sl.no: 16(225 )	-	0	-
table 1 sl.no: 17(250.0)	-	0	-
table 1 sl.no: 18(280.0)	-	0	-
table 1 sl.no: 19(315.0)	-	0	-
2.2(Manufacture)	-	0	-
2.2.2, Table 1(Size)	-	0	-
2.2.2, Table 1(45 ̊ Elbow Laying Length)	-	0	-
2.2.3( inside diameter of the socket)	-	0	-

Complete

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Table 1(Dimension of 11 1/4° bends)	-	500	Full Testing Chargers refer to IS 10124 (P-1)
3.2.2, Table 2(Dimension of 11 1/4° bends for Elastomeric sealing ring joint)	-	500	Full Testing Chargers refer to IS 10124 (P-1)
3.2.3(Socket, Measurement)	-	500	Full Testing Chargers refer to IS 10124 (P-1)
3.1(General)	-	12000	Full Testing Chargers refer to IS 10124 (P-1)

Complete

IS 10124 : Part 12 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 12 specific requirements for 22½ degree bends (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Table 1(Dimensions of 22 ½ deg Bends)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
3.2.2, Table 2(Dimensions of 22 ½ deg Bend for Elastomeric Sealing Ring Joint)	-	500	Full Testing Charges refer to IS 10124 (P-1)
3.2.3(Socket, measurements)	-	500	Full Testing Charges refer to IS 10124 (P-1)
3.1(General)	-	12000	-

Complete

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Table 1(Dimensions of 30 deg Bends)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
3.2.2, Table 2(Dimensions of 30 deg Bend for Elastomeric Sealing Ring Joint)	-	500	Full Testing Charges refer to IS 10124 (P-1)
3.1(General)	-	12000	-

Complete

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 1, table 1(Dimensions)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 45° Bend for Elastomeric Sealing Ring Joint)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 45o Bend)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
3.1(General)	-	12000	Full Testing Charges refer to IS 10124 (P-1)
3.2, 3.2.1, Fig 2(Manufacture)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	-

Complete

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 1, table 1(Dimensions)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 60o Bend for Elastomeric Sealing Ring Joint)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
Table 1 (Clauses 3.2.2, 3.2.3, and Fig. 1)(Dimensions of 60o Bends)	-	1000	Full Testing Charges refer to IS 10124 (P-1)
3.1(General)	-	12000	Full Testing Charges refer to IS 10124 (P-1)
3.2, 3.2.1, Fig 2(Manufacture)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	-

Complete

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 2, table 2(Dimensions)	-	1500	Full Testing charge refer to IS 10124 (P-1)@14000
Table 2 (Clause 3.2.2, and Fig. 2)(Dimensions of 90o Bend for Elastomeric Sealing Ring Joint)	-	1500	Full Testing charge refer to IS 10124 (P-1)@14000
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of 90o Bends)	-	1500	Full Testing charge refer to IS 10124 (P-1)@14000
3.1(General)	-	12000	Full Testing charge refer to IS 10124 (P-1)@14000
3.2, 3.2.1, Fig 2(Manufacture)	-	500	-
3.2.3(the socket measurement shall comply with IS 10124 (Part 1).)	-	500	-

Complete

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.3.2, table 1, fig 1(Dimensions)	-	1000	Full Testing Charge refer to IS 10124 (P-1)@14000
3.3.3(socket measurement shall comply with IS 10124 (Part 1).)	-	500	Full Testing Charge refer to IS 10124 (P-1)@14000
Table 1 (Clauses 3.3.1 and 3.3.2)(Dimensions of Threaded Adaptors)	-	1000	Full Testing Charge refer to IS 10124 (P-1)@14000
3.1(General)	-	12000	Full Testing Charge refer to IS 10124 (P-1)@14000
3.2(Materials)	-	500	-
3.3, 3.3.1, Fig 1(Manufacture)	-	500	-

Complete

IS 10124 : Part 6 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 6 specific requirements for flanged tail pieces with metallic flanges (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 2, table 2(Dimensions)	-	1000	Full test Charges refer to IS 10124 (P-1)
Table 1 (Clause 3.2.2, and Fig. 1)(Dimensions of PVC Flanged Tail Piece with Metallic Flanges)	-	500	Full test Charges refer to IS 10124 (P-1)
Table 2 (Cl.3.2.2, and Fig.1)(Dimensions of Flanged Tail Piece with Metallic Flange for Elastomeric Sealing Ring Joint)	-	500	Full test Charges refer to IS 10124 (P-1)
3.1(General)	-	12000	Full test Charges refer to IS 10124 (P-1)
3.2, 3.2.1, Fig 1(Manufacture)	-	500	-

Complete

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 1(Dimensions)	-	2000	Full Testing Charge refer to IS 10124 (P-1)@14000
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Equal Tees)	-	500	Full Testing Charge refer to IS 10124 (P-1)@14000
3.1(General)	-	12000	Full Testing Charge refer to IS 10124 (P-1)@14000
3.2, 3.2.1, Fig 1(Manufacture)	-	500	-

Complete

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 1(Dimensions)	-	2000	FULL TESTING CHARGES AS PER 10124 PART 1
Table 1(Cl.3.2.2, and Fig.1)(Dimensions of Caps)	-	500	FULL TESTING CHARGES AS PER 10124 PART 1
3.1(General)	-	12000	FULL TESTING CHARGES AS PER 10124 PART 1
3.2, 3.2.1, Fig 1(Manufacture)	-	500	-
3.1(General)	-	0	-

Complete

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.2, Fig 1(Dimensions)	-	1000	Full Testing Charge refer to IS 10124 (P-1)@14000
Table-1 (cl.3.2.2, Fig 1)(Dimensions of Straight Reducers)	-	1000	Full Testing Charge refer to IS 10124 (P-1)@14000
3.1(General)	-	12000	Full Testing Charge refer to IS 10124 (P-1)@14000
3.2, 3.2.1, Fig 1(Manufacture)	-	500	-

Complete

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2.1, Table-1, Fig-1(Nominal size)	-	500	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	500	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
3.2.1, Table-1, Fig-1(B)	-	500	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	4000	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	0	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	0	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Mercury (all three extracts))	-	0	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-10)(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction))	-	0	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	1000	Full Testing Charge refer to IS 10124 (P-1)& IS 10124 : Part 2
3.1(General)	-	500	Full Testing Charge refer to IS 10124 (P-1)
10.7 of IS 4985(Sulphated Ash content, Annex-B of IS 4985)	-	1500	-
3.2.1, Table-1, Fig-1(Plumbing)	-	250	-
Clause 3.2.2, and Fig. 2(Nominal size)	-	500	-
Clause 3.2.2, and Fig. 2.(B)	-	500	-
Clause 3.2.2, and Fig. 2.(Minimum wall thickness for working pressure)	-	500	-

Complete

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500	-
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	500	-
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	500	-
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	500	-
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	2000	-
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	4000	-
8(Marking)	-	500	-
6.3(Effect on water test)	-	4000	-
3(Material)	-	4100	Testing charges ( VCM Content + K- Value) ( 3000+1100)
4(Size of fitting)	-	500	-
3.2.3(socket, measurements)	-	500	-
3.1(Material)	-	0	Testing charges ( VCM Content + K- Value) ( 3000+1100)

Complete

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

17000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	4000	-
5.2 and Table 1 x(Ash content )	-	1500	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	3000	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1500	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	-
4.2(Tapes – Linear Density )	-	500	-
4.2(Construction)	-	500	-
4.4.1(Liner)	-	1000	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	500	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	-
4.3.2(Mouth)	-	1000	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	500	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	2000	-
4.3.1(Bottom Seam)	-	2000	-
4.5 and Table 1 i(Capacity)	-	500	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	500	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	2000	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	2000	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
4.1(Raw Material)	-	9500	ALL TEST INCLUDED
4.3(Sacks)	-	1000	-
4.4(Liner IS 10146 or IS 10910.)	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1500	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	1500	-
5.2 and Table 1 x(Ash content )	-	1500	-
3(TYPES)	-	0	-
4.2(Construction)	-	0	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(stitches/dm)	-	0	-
4.4(Mass of the loose liner )	-	0	-
4.4(Width of the loose liner)	-	0	-
4.4(Length of the line)	-	0	-
4.4(Bottom seam of the loose liner)	-	0	-
3(TYPES)	-	0	-
4.1(Raw Material)	-	0	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4(Liner IS 10146 or IS 10910.)	-	0	-
4.4(Mass of the loose liner )	-	0	-
4.4(Width of the loose liner)	-	0	-
4.4(Length of the line)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.4(Bottom seam of the loose liner)	-	0	-
4.4.1(Liner)	-	0	-
4.5 and Table 1 i(Capacity)	-	0	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	-
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	0	-
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	0	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	-
4.2(Tapes – Linear Density )	-	0	-

Complete

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 and Table 1 x(Ash content )	-	1500	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1500	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1500	-
4.3.1(Bottom Seam)	-	1000	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	11500	-
4.4 and Table 1 i(Capacity)	-	500	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	500	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	1500	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	1500	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	-
5.1 and Table 1 v(Mass of sack )	-	500	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1500	-
4.3.2(Mouth)	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
4.1(Raw Material)	-	500	-
4.3(Sacks)	-	500	-
3(TYPES)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3.1( The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(The number of stitches/dm)	-	0	-
3(TYPES)	-	0	-
4.1(Raw Material)	-	0	-
4.2(Tapes – Width IS 6192 and IS 11197)	-	0	-
4.2(Tapes – Linear Density )	-	0	-
4.2(Construction)	-	0	-
4.3(Sacks)	-	0	-
4.3.1(Bottom Seam)	-	0	-
4.3.1( The two rows of stitches shall be separated from each other)	-	0	-
4.3.1( The outer stitch)	-	0	-
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	-
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	-
4.3.1(The number of stitches/dm)	-	0	-
4.3.2(Mouth)	-	0	-
4.4 and Table 1 i(Capacity)	-	0	-
5.2 and Table 1 ii a(Dimensions Inside Length)	-	0	-
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	0	-
5.2 and Table 1 iv(Picks per dm )	-	0	-
5.1 and Table 1 v(Mass of sack )	-	0	-
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	0	-
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	0	-
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	0	-
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	-
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	-
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
5.2 and Table 1 x(Ash content )	-	0	-

Complete

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

18000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.3.1(Bottom seam (IS 10789))	-	500	-
4.2 and Table 1 ii(Dimensions )	-	500	-
5.2 and Table 1 iv(Picks per dm )	-	500	-
5.2 and Table 1 iii(Ends per dm )	-	500	-
4.2 and Table 1 v(Mass of sack )	-	500	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	1000	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1000	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	1000	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	11500	-
4.2 and Table 1 x(Ash content )	-	1000	-
3.1(Material Identification)	-	2000	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	1000	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	500	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	500	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	500	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	500	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	500	-
3.2(Unlaminated Fabric Mass )	-	500	-
3.1(Overall Migration)	-	1000	-
3.2(Density)	-	1000	-
3.2(MFI)	-	1000	-
3.3.1(Bottom seam (IS 10789))	-	500	-
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	500	-
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	0	-
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	0	-
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	0	-
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	0	-
3.2(Unlaminated Fabric Mass )	-	0	-
5.2 and Table 1 iii(Ends per dm )	-	0	-
5.2 and Table 1 iv(Picks per dm )	-	0	-
4.2 and Table 1 v(Mass of sack )	-	0	-
4.2 and Table 1 vi(Average breaking strength of fabric )	-	0	-
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	0	-
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	-
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	0	-
4.2 and Table 1 x(Ash content )	-	0	-

Complete

IS 10889 (2004)

High density polyethylene films (First Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Grades)	-	500	-
5.1(Materials)	-	2200	-
6.1.1(Appearance)	-	500	-
6.1.2(Film Form)	-	250	-
6.1.3(Odour )	-	250	-
6.1.4(Density)	-	1200	-
6.1.5(Melt Flow Rate)	-	1500	-
6.2.2, Table 2(Nominal Width)	-	250	-
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	500	-
6.4.1(Tensile Strength at Break)	-	1800	-
6.4.1, Table 4(Direction)	-	1800	-
6.4.2(Elongation at Break)	-	2000	-
6.4.2, Table 5(Direction)	-	0	-
6.4.3(Impact Resistance (Falling Dart))	-	2000	-
6.4.3, Table 6(Impact Failure Load)	-	2000	-
6.1.6(Black Film)	-	2000	-
5.2(Black Compound)	-	500	-
6.2.1, Table 1(Nominal Thickness)	-	500	-
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	500	-
6.3, Table 3(Yield Tolerance)	-	500	-
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	500	-
6.4.1, Table 4(Grade 1 and 2)	-	250	-
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	500	-
6.4.3, Table 6(Average Thickness of Film)	-	250	-

Complete

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.6a(Carbon Black Content, Annex-A)	-	1500	-
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	1500	-
Cl.5.1.6(b)(Ash content)	-	1500	-
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	1500	-
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	1000	-
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	1000	-
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	1000	-
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	1000	-
Clause 9.1 (Table 4)(Break Elongation)	-	1000	-
Clause 9.1 (Table 4)(Yield Elonation)	-	1000	-
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1000	-
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1000	-
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4000	-
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4000	-
5.1.1(Appearance)	-	500	-
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1000	-
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	1000	-
5.1.2(Film Form)	-	500	-
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1500	-
5.2.2(Tolerance on Thickness, Annex-A)	-	500	-
5.1.3(Odour)	-	500	-
8.1, Table 3(Puncture resistance , Annex C)	-	2000	-
9.1, Table 4(Puncture resistance , Annex C)	-	2000	-
8.1, Table 3(Tear resistance , Annex B)	-	1000	-
9.1, Table 4(Tear resistance , Annex B)	-	1000	-
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1000	-
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1000	-
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1000	-
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1000	-
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1000	-
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1000	-
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1000	-
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1000	-
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1500	-
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1500	-
5.1.6b(Ash Content, Annex-A)	-	0	-
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	-
Clause 9.1 (Table 4)(Break strength)	-	0	-
Clause 9.1 (Table 4)(Yield strength)	-	0	-
Clause 8.1(Table 3)(Break Elongation)	-	0	-
Clause 8.1(Table 3)(Break strength)	-	0	-
Clause 7.1(Table 2)(Dart Impact Strength)	-	0	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	0	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0	-
Clause 5.2.3(Tolerance on Width)	-	250	-
5.2.1.1(Nominal Thickness)	-	250	-
5.2.1.2(Nominal width)	-	250	-
Cl.5.1.6(a)(Carbon Black Content)	-	0	-
Cl.5.1.6(c)(Dispersion of Carbon Black)	-	0	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	0	-

Complete

IS 15265 (2003)

Flexible pvc pipes or polymer reinforced thermoplastic hoses for suction and delivery lines of agricultural pumps - Specification

27000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 Table 2(Length)	-	500	-
5.1 Table 1(Internal Diameter)	-	500	-
6.1 Table 3(Hydrostatic test atatmospheric condition)	-	1500	-
6.2 Table 4(Hydrostatic test at 55± 2°C)	-	1500	-
6.3(Pressure Impulse Test Annex B)	-	12000	-
6.4(Vaccum Test requirement Annex C)	-	2200	-
6.5(Reinforce Facture Test Requirement Annex D)	-	1500	-
6.6(Minimum Bend Radius Requirement- Annex E )	-	1500	-
6.7(Cold Bend Radius Requirement- Annex E )	-	1500	-
6.8(Loss in Mass on Heating- Annex F)	-	2500	-
6.9(Effect of Sunlight)	-	3500	-

Complete

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Di men sion)	-	500	-
4.2(Carbon black- a)carbon content)	-	0	-
4.3(Anti-oxidant)	-	0	-
4.2(Carbon black- b) Dispersion of carbon black)	-	0	-
4.1(Quick Coupled Male and Female Couplers)	-	1500	-
Cl.4.1.3(Thermal Stabi lity)	-	2000	-
Cl.4.1.3, T-1(Volatile Matter)	-	1500	-
Cl.4.1.3, T-1(Water Content)	-	1000	-
4.1.4(a)(Holding Attachments for Coupler Parts)	-	3000	-
7.5(Density)	-	1500	-
4.1.5(Rubber rings- B) Change in hardness)	-	0	-
5(Dimensions of pipe - i) Outside diameter)	-	500	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	500	-
5.1.2(Ovality)	-	500	-
Cl.7.1.5(Fusion Compatibility)	-	1500	-
4.2.7(1 Dimensions of Quick Coupled Pipes and Fittings)	-	500	-
6.1.3.1.1(Weldability Test)	-	1500	-
Cl.4.1.3, T-1(Volatile Matter)	-	1500	-
4.1.3(Workmanship and appearance)	-	500	-
Cl.4.1.3(Thermal Stabi lity)	-	2000	-
7.3(Tensile Test- i) Tensile Strength)	-	1500	-
7.3(Tensile Test - ii)Elongation at Break)	-	1500	-
4.1.5(Rubber rings- A)Shore hardness (Shore-A))	-	0	-
Cl.6.2.6(Rubber Ring Hardness)	-	500	-
7.2(Reversion Test)	-	1500	-
Cl.7.1.3(Reversion Test)	-	1500	-
Cl.7.1.7(MFR Test)	-	1500	-
7.6(Melt Flow Rate)	-	1500	-
Cl.4.1.3(MFR Test)	-	1500	-
6.2 b(Material Identification - Male & Female Coupler)	-	2000	-
Cl.7.2.l(Leakage Test)	-	2000	-
4.1 (b)(HDPE couplers —)	-	500	-
7.1 Table -2(Hydraulic Characteristics)	-	3000	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	3000	-
Cl.7.1.2(Hydraulic Characteristic)	-	3000	-
Cl.4.1.4(Carbon Black Content)	-	1500	-
4.1.6(Antioxidant)	-	1500	-
4.1.4(The Carbon Content and Dispersion)	-	1500	-
Cl.7.2.3(Weld ability Test)	-	2000	-
7.1.4(Tensile strength & elongation)	-	2500	-
7.1.3(Reversion)	-	2000	-
7.2.2(Hydraulic Proof test 1hour / 27°C)	-	2500	-
6(Visual Appearance)	-	250	-
7.1(Hydraulic Characteristics - Quality test)	-	1500	-
7.1(Hydraulic Characteristics - Acceptance test)	-	2000	-
7.4(Fusion Compatibility Test- a) Quality test)	-	1500	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	2000	-
7.6(Melt Flow Rate)	-	1000	-
7.6(Melt now Rate (MFR))	-	1000	-
7.5(Density)	-	1000	-
7.4 Table-2(Fusion Compatibility Test)	-	1000	-
7.3(Tensile Test)	-	1000	-
7.2(Reversion Test)	-	1000	-
6.1(VISUAL APPEARANCE)	-	250	-
5.1 table -1(DIMENSIONS OF PIPES)	-	500	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	1000	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1000	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	1000	-
4.1(melt flow rating (MFR) shall not exceed 1.10 g/10 min.)	-	1000	-
3(CLASSIFICATION OF PIPES)	-	0	-
4.1(Quick Coupled Male and Female Couplers)	-	0	-
4.1.4(Holding attachments for coupler parts)	-	0	-
4.1.5(Rubber rings- C)Rubber ring shall be of black colour:)	-	0	-
6.1.3(Weldability Test- a) Quality test)	-	1000	-
6.1.3(Weldability Test- b) Acceptance test)	-	1000	-
3(Quick Coupled pipes)	-	0	-
3(QUICK COUPLED PIPES)	-	0	-
4(QUICK COUPLED FITTINGS)	-	0	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31000(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 31500(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 40800(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 51300(Remarks)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 52000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 53000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Aluminium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Chromium Content)	-	0	-
C. 4.1.1.1.1, IS 737-2008, Cl. 6, Table-1 , Desig 55000(Cr + Mn)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Copper Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Magnesium Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Silicon Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Iron Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Manganese Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Nickel Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Zinc Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Lead Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Tin Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Titanium Content)	-	0	-
C. 4.1.1.1.1, IS 617-1994, Cl. 5, Table-1 , Desig 4600(Aluminium Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Carbon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Manganese Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Sulphur Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1)(Phosphorous Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Killed(Aluminium Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed(Silicon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Silicon Content)	-	0	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Al-Si-Killed(Aluminium Content)	-	0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 10(Cabon Black Content)	-	0	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16(Carbon Black Dispersion)	-	0	-
4.1 .1.2.1(HDPE couplers)	-	0	-
4.1 .1.2.2(HDPE couplers)	-	0	-
4.1.3(Workmanship and Appearance)	-	0	-
4.1.4(b)(Holding Attachments for Coupler Parts)	-	0	-
4.1.5(Rubber Ring)	-	0	-
4.2.1(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.2(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.3(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.5(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.6(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.7(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.4(Quick Coupled ~pe HDPE Fittings)	-	0	-
4.2.7(Reducers Table 1 and 2 of IS 8008 (Part 4))	-	0	-
4.2.7(Ferrule reducers Table 1 of IS 8008 (Part 5))	-	0	-
4.2.7(Pipe ends Table 1 of IS 8008 (Part 6))	-	0	-
4.2.7(End caps Table 1 of IS 8008 (Part 9))	-	0	-
4.2.7(Insert vatve couplers Table 1 of IS 8008 (Part 3))	-	0	-
4.2.7(Valve openers Table 1 of IS 8008 (Part 2))	-	0	-
5.2(Dimensions of Quick Coupled Sprinkler Saddles Table 1.)	-	0	-
6.1(Quick Coupled Pipes and Fittings)	-	0	-
6.1.1, 6.1.1.1(Leakage Test)	-	0	-
6.1.1, 6.1.1.1(Leakage Test)	-	0	-
6.1.2.2(Hydraulic Proof Test)	-	0	-
6.1.2.2(Hydraulic Proof Test)	-	0	-
6.1.3, 6.1.3.1(Weldability Test)	-	0	-
6.1.3.2(Quick coupled fittings)	-	0	-
6.2, 6.2.1(Quick Coupled Fittings)	-	0	-
7.2.1(Visual and Workmanship Requirement)	-	0	-
6.3.3(Material Identification - Insert Valve Coupler)	-	0	-
6.3.3(Material Identification - Insert Valve Coupler)	-	0	-
6.3.4()	-	0	-
6.3.5(Material Identification - Saddle)	-	0	-
6.3.5(Material Identification - Pipe Ends)	-	0	-
6.3.6(Quick Coupled Pump Connectors - Visual)	-	0	-
4.2(Metallic Couplers)	-	0	-
4.2(Metallic Couplers)	-	0	-
7.2.1(Leakage Test)	-	0	-
Cl.4.1.3(Den sity Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3(MFR Test)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Volatile Matter)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.3, T-1(Water Content)	-	0	-
Cl.4.1.4(Carbon Black Content)	-	0	-
Cl.4.1.4(Carbon Black Content)	-	0	-
Cl.4.1.4(Carbon Black Di spersion)	-	0	-
Cl.4.1.4(Carbon Black Di spersion)	-	0	-
Cl.4.1.4(Carbon Black Di spersion)	-	0	-
Cl.5.1.l(Outside Diameter)	-	0	-
Cl.5.1.l(Outside Diameter)	-	0	-
Cl.6.2.L(Wall Thickness)	-	0	-
Cl.6.2.4(Workmanship and Appearance)	-	0	-
Cl.6.2.6(Ageing Test)	-	0	-
Cl.7.1.l(Visual Anneara nce)	-	0	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.2(Hydraulic Characteristic)	-	0	-
Cl.7.1.3(Reversion Test)	-	0	-
Cl.7.1.4(Tensile Test)	-	0	-
Cl.7.1.4(Tensile Test)	-	0	-
Cl.7.1.4(Tensile Test)	-	0	-
Cl.7.1.4(Elongation)	-	0	-
Cl.7.1.4(Elongation)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.5(Fusion Compatibility)	-	0	-
Cl.7.1.6(Corrected Density)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.1.7(MFR Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.l(Leakage Test)	-	0	-
Cl.7.2.2(Cl.7.2.2)	-	0	-
Cl.7.2.3(Weld ability Test)	-	0	-
6.2 (iii) Rubber Rings (a) Shore hardness(Shore hardness)	-	0	-
6.2 (iii) Rubber Rings (b) Accelerated Storage test(Accelerated Storage test)	-	0	-
5(Dimensions of pipe (outside diameter, ovality, wall thickness))	-	0	-
6.1(Thermal Stability (OIT))	-	0	-
6.1(Volatile Matter)	-	0	-
6.1(Water content)	-	0	-
6.1(Tensile strength at Yield & Elongation at break)	-	0	-
6.1(Carbon Black Content)	-	0	-
6.1(Carbon Black Dispersion)	-	0	-
6.2.1(Base Density x 2)	-	0	-
6.2.1(Melt Flow Index x 2)	-	0	-
6.2.1(Thermal Stability (OIT) x 2)	-	0	-
6.2.1(Volatile Matter x 2)	-	0	-
6.2.1(Water content x 2)	-	0	-
6.2.1(Carbon Black Content x 2)	-	0	-
6.2.1(Carbon Black Dispersion x 2)	-	0	-
6.2.1(Wall thickness of male & female coupler)	-	0	-
6.2.4(Workmanship and appearance (Visual))	-	0	-
6.2.5(Holding attachment for coupler parts)	-	0	-
6.2.5(Material Composition (Chemical Analysis))	-	0	-
6.2.5(Coating thickness (Hot dip Galvanized or Electroplated or Passivated or Powder Coated))	-	0	-
6.2.6(Material Identification (Chemical Analysis))	-	0	-
6.2.6(Color)	-	0	-
6.2.6(Rubber Ring Hardness Shore – A (Before Ageing))	-	0	-
6.2.6(Ageing Charges for rubber ring)	-	0	-
7.1.1(Visual appearance of pipes)	-	0	-
7.1.2(Hydraulic Characteristics)	-	0	-
7.1.2((a) Acceptance Test (48 hrs) / 80˚ C)	-	0	-
7.1.2((b) Type test ( 165 hrs) / 80˚ C)	-	0	-
7.1.5(Fusion Compatibility test)	-	0	-
7.1.5((a) Acceptance Test (48 hrs) / 80˚ C)	-	0	-
7.1.5((b) Type test ( 165 hrs) / 80˚ C)	-	0	-
7.1.6(Corrected Density)	-	0	-
7.1.6(Base Density)	-	0	-
7.1.6(Carbon black Content)	-	0	-
7.1.7(Melt Flow Rate (MFR))	-	0	-
7.2.1(Leakage test 1hour / 27°C)	-	0	-
7.2.3((a) Acceptance Test (48 hrs) / 80˚ C)	-	0	-
7.2.3((b) Type test ( 165 hrs) / 80˚ C)	-	0	-
8(Supply of pipe (Visual))	-	0	-
4.1.1 (Table-1)(Density)	-	0	-
4.1.1 (Table-1)(Melt Flow Index)	-	0	-
4.1.1 (Table-1)(Oxidation Induction Time)	-	0	-
4.1.1 (Table-1)(Volatile Matter)	-	0	-
4.1.1 (Table-1)(Water content)	-	0	-
4.1.1 (Table-1)(Tensile strength at Yield & Elongation at break)	-	0	-
4.1.4(Carbon Black Content)	-	0	-
4.1.4(Carbon Black Dispersion)	-	0	-
4.1.1(Polyethylene material)	-	0	-
4.1.3, Table 1,(i)(Bass density)	-	0	-
4.1.3, Table 1,(ii)(Melt flow rate)	-	0	-
4.1.3, Table 1,(iii)(Thermal stability)	-	0	-
4.1.3, Table 1,(iv)(Volatile matter)	-	0	-
4.1.3, Table 1,(v)(Water content)	-	0	-
4.1.3, Table 1,(vi)(Minimum tensile strenght at yield)	-	0	-
4.1.3, Table 1,(vii)(Minimum elongation at break)	-	0	-
4.1.5(Carbon Black Specification)	-	3500	-
4.1.7(Rework Material)	-	0	-
4.2(Metallic Couplers)	-	0	-
5.1, Table 1,(i)(Plain pipes)	-	0	-
5.1, Table 1,(ii)(90° Bends and tee)	-	0	-
5.1, Table 1,(iii)(Base pipe )	-	0	-
5.1, Table 1,(iv)(PCN)	-	0	-
5.1, Table 1,(v)(Reducers, ferrule reducers)	-	0	-
5.1, Table 1,(vi)(End caps, insert valve coupler, valve openers)	-	0	-
5.1, Table 1,(vii)(Riser pipe and socket)	-	0	-
7.1.1(Visual Appearance and Workmanship)	-	0	-
7.1.2(Hydraulic Performance Characteristic)	-	0	-
7.1.3(Reversion Test)	-	0	-
7.1.4(Tensile Test)	-	0	-
7.1.5(Fusion Compatibility Test)	-	0	-
7.1.6(Corrected Density)	-	0	-
7.1.7(Melt flow rate)	-	0	-
7.2.1(Leakage Test)	-	0	-
7.2.2(Hydraulic Proof Test)	-	0	-
7.2.3(Weldability Test)	-	0	-
7.3(Quick Couple Fitting)	-	0	-
10(Marking)	-	0	-
5.1.2(Squareness)	-	0	-

Complete

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.3(Determination of Emitter Exponent)	-	1000	-
7.1(Construction and workmanship)	-	500	-
7.2(Flow path in emitters)	-	1000	-
7.3.1(Resistance to Hydrostatic pressure)	-	1000	-
7.3.2(Resistance to Hydrostatic pressure)	-	1000	-
7.3.3(Resistance to Hydrostatic pressure)	-	1000	-
7.4.1(Emitter Pull Out In-line emitters)	-	1000	-
7.4.2(Emitter Pull Out On-line emitters)	-	1500	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	1500	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	1000	-
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	1000	-
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	1000	-
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	0	-
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	-
4(Classification)	-	0	-
5.1(Connections)	-	0	-
5.2(Emitter Ends)	-	0	-
5.3(Materials)	-	1500	-
6.1(Test Specimens)	-	0	-
6.2(Test Conditions)	-	0	-
6.3(Accuracy or Measuring Devices)	-	0	-
7.1(Construction and Workmanship)	-	0	-
7.2(Flow Paths In Emitter)	-	0	-
7.3(Resistance to Hydrostatic Pressure)	-	0	-
7.4(Emitter Pull-out)	-	0	-
7.4.2(On-Line Emitters)	-	0	-
8.1(Uniformity of Emission Rate)	-	0	-
8.1.1(Number of Test Samples)	-	0	-
8.2.2(Unregulated Emttters)	-	0	-
8.2.3(Regulated Emitters)	-	0	-
8.3(Determiaatlon of Emitter Exponent)	-	0	-
9(Marking)	-	0	-
8.1.2(Unregulated Emitters)	-	0	-
8.1.3(Regulated Emitters)	-	0	-
8.2(Emission Rate as a Function of Inlet Pressure)	-	0	-
8.2.1(Selection of Telt Sample)	-	0	-
7.4.1(In-Line Emitters)	-	0	-

Complete

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	1500	-
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	1500	-
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	1500	-
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	1500	-
6.2.2(Fittings)	-	0	-
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000	-
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	1000	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1500	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	500	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	500	-
8.3.3(Flow Paths in Emitting Unit)	-	500	-
8.3.4(Spacing ofEmitter Units)	-	500	-
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	4000	-
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	4000	-
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	1200	-
8.8(Determination of Emitting Unit Exponent)	-	1000	-
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	250	-
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	-
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	1000	-
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	1000	-
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	1000	-
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	1000	-
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	2500	-
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	2500	-
8.5(Resistance to Tension at Elevated Temperature)	-	3200	-
4.1 a(Identification)	-	2500	-
6.3(General)	-	1500	-
6.1.1, Table 1,(ii)(Inside Diameter)	-	500	-
6.1.1, Table 1,(i)(Nominal Diameter)	-	500	-
6.1.1, Table 1,(iv)(Wall Thickness)	-	500	-
6.1.1, Table 1,(iii)(Tolerance on I.D)	-	500	-
5.1.2 (Ref. Cl 4.3 of IS 12786 : 1989)(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	500	-
6.3(General)	-	250	-
8.2.1(Unregu/Qt~d Emining Pipe)	-	500	-
8.2.2(Regulated Emitting Pipes)	-	500	-
4.1 a(Identification)	-	0	-
4.1 c(Volatile matter Extract)	-	0	-
4.1 d(Density)	-	0	-
4.1 d(MFI @ 1900C/2.16 Kg)	-	1000	-
4.2(Carbon black content)	-	1500	-
4.2(Carbon black dispersion)	-	1500	-
5.1(Materials)	-	1000	-
6.2(Fittings)	-	250	-
6.3(General)	-	250	-
7.1(Test Specimens)	-	0	-
7.2(Order of Tests)	-	0	-
7.3(Testing Conditions)	-	0	-
7.4(Accuracy of Measuring Devices)	-	0	-
8.1(Uniformity of Emission Rate)	-	500	-
8.1.2(Unregulated Emitting Pipes)	-	250	-
8.1.3(Regulated Emitting Pipes)	-	250	-
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	0	-
8.2.1(Unregulated Emitting Pipes)	-	0	-
8.2.2(Regulated Emitting Pipes)	-	0	-
8.3.1(Wall Thickness ofEmitting Pipe)	-	0	-
8.3.2(Inside Diameter ofEmitting Pipe)	-	0	-
8.3.3(Flow Paths in Emitting Unit)	-	0	-
8.3.4(Spacing of Emitter Units)	-	0	-
8.4(Resistance of Emitting Pipes to Hydrostatic Pressure)	-	5000	-
8.5(Resistance to Tension at Elevated Temperature)	-	5000	-
8.6(Resistance to Pull Out ofJoints Between Fitting and Emitting)	-	2000	-
8.7.1(Acceptance Test)	-	4000	-
8.7.2(Type Test)	-	4000	-
8.8(Determination of Emitting Unit Exponen)	-	3500	-
9.1(Non-regulated Emitting Pipe)	-	0	-
9.2(Regulated Emitting Pipe)	-	0	-
10.1(Marking)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-
8.5(Resistance to Tension at Elevated Temperature)	-	0	-

Complete

Bureau of Indian Standards

The National Standards Body of India

ARDM Labs Pvt Ltd

A-80, G. T. KARNAL ROAD INDUSTRIAL AREA, AZADPUR, DELHI, North, Delhi, 110033

9810068016 ardmlabs@gmail.com

Scope List