BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

Reset

250 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 2082 (2018)

Stationary storage type electric water heaters - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
(Cl.8 of IS 302-2-21:2011) (Protection Against Access to Live Parts)	-
(Cl.10 of IS 302-2-21: 2011) (Power Input & Current)	-

Partial

IS 2556 : Part 6 (2021)

Vitreous China sanitary appliances - Specification: Part 6 Specific requirements of urinal and partition plates (fifth revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.1 (DIMENSIONS AND TOLERANCES)	-
Cl 7.7 ()	-
Cl 7.1.2 ()	-
Cl 8 ()	-

Partial

IS 14862 (2000)

Fibre cement flat sheets - specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1.1 (Nominal Length )	-
5.1.1 (Nominal Width)	-
5.1.2 (Thickness)	-
5.1.4.1 (Straightness of edges - Length )	-
5.1.4.1 (Straightness of edges - Width )	-

Partial

IS 15786 (2008)

Prelaminated cement bonded particle board - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 10.3 (Moisture content)	-

Partial

IS 7933 (2022)

Specification for Flexible Polyurethane Foam for Domestic Mattresses First Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. No. 5.4 (Dimensions and Tolerances)	-

Partial

IS 302 : Part 1 (2008)

Safety of household and similar electrical appliances: Part 1 general requirements (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (Marking and instructions)	-
8.1.1 (Protection against live parts in all positions)	-
8.1.2 (Protection against live parts in openings)	-
9 (Starting of motor operation test requirements and tests)	-
10.1 (Power input)	-
10.2 (Current input)	-
11.1 (General)	-
11.2 (General)	-
11.3 (Heating)	-
13.1 (General)	-
13.2 (Leakage current at operating temperature)	-
13.3 (Electric Strength at operating temperature)	-
14 (Transient Over Voltages)	-
8.1.3 (Protection against live parts in visible glowing heating elements)	-
8.1.4 (Protection against live parts against protective impedance)	-
15.0 (General)	-
15.1 (Ingress Protection test other than IPX0 (IP test))	-
15.2 (Spillage Test)	-
15.3 (Humidity Test)	-
16.0 (General)	-
16.2 (Leakage Current (after Clause 15))	-
16.3 (Electric Strength (after clause 15 and 16.2))	-
17 (Over Load Protection of Transformers and associated circuits)	-
19 (Abnormal Operation)	-
20 (Stability test)	-
21 (Mechanical Strength Test)	-
22 (Construction verification related test)	-
23 (General)	-
24 (Components)	-
25 (Supply connection and external flexible cords)	-
26 (Terminals for external conductors)	-
27 (Provision for earthing)	-
28 (Screw test and connections)	-
29 (clearance, creepage distances and solid insulation)	-
30.1 (Ball pressure test)	-
30.2 (Glow Wire Test)	-
30.2 (Needle Flame Test)	-
31 (Resistance to Rusting)	-

Partial

IS 2785 (2022)

CHEESE - SPECIFICATION (Second Revision of IS 2785)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.1 (Appearance - IS 2785 :2022)	-
5.2.2 (Odour and Flavour-IS 2785 :2022)	-
5.2.3 (Texture and Consistency)	-
3 and 5.3 Table 1 (iii) (a) Processed Cheese (a) Moisture IS- 2785-2022 (Processed cheeze when sold in package othen than tin))	-
4 and 5.3 Table 1 (iii) (a) Processed Cheese (b) Moisture IS- 2785-2022 (Processed cheeze in chiplets, packed sliced))	-
3 and 5.3 Table 1 (iii) (a) Processed Cheese (Milk fat (On dry basis) IS 12758-2005)	-
3 and 5.3 Table 1 (iii) (b) Processed Cheese Spread (Moisture IS- 2785-2022)	-
3 and 5.3 Table 1 (iii) (b) Processed Cheese Spread (Milk fat (On dry basis) IS 12758-2005)	-
5.4 Table 2-i (Coliform-IS 5401(P-1):2012)	-
5.4 Table 2-ii (S.aureus-IS 5887(P-8/Sec-1):2002)	-
5.4 Table 2-iv (E.coli-IS 5887(P-1):1976)	-
5.4 Table 2-v (Salmonella spp.-IS 5887(P-3/Sec-1):2020)	-
5.4 Table 2-vi (L.monocytogenes-IS 14988(P-1):2020)	-
5.5 Table 3-i (Aerobic Colony count - IS 5402 (Part 2))	-
5.4 Table 2-iii (Yeast & Mould count-IS 5403:1999)	-
5.4 Table 2-ii (S.aureus-IS 5887(P-8/Sec-1):2002)	-

Partial

IS 1664 (2002)

Mineral mixtures for supplementing cattle feeds - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

IS 2080 (2021)

Specification for stabilized hydrogen peroxide First Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description - IS 2080:2021)	-
4.2 (Strength - IS 2080:2021)	-
4.4/Table 1 (i) (Acidity (as H2SO4) - IS 2080:2021)	-
4.4/Table 1 (ii) (Residue on Evaporation - IS 2080:2021)	-
4.4/Table 1 (iv) (Iron (as Fe) - IS 2080:2021)	-
4.4/Table 1 (v) (Copper (as Cu) - IS 2080:2021)	-
4.4/Table 1 (vi) (Lead (as Pb) - IS 2080:2021)	-
4.4/Table 1 (vii) (Arsenic (as As2O3) - IS 2080:2021)	-
4.4/Table 1 (iii) (Residue on Ignition - IS 2080:2021)	-

Partial

IS 2185 : Part 3 (1984)

Concrete Masonry Units Part 3 Autoclaved Cellular Aerated Concrete Blocks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8 (Physical requirments)	-
8.2 (Physical requirments-Dimensions-Length)	-
8.2 (Physical requirments-Dimensions-Height)	-
8.2 (Physical requirments-Dimensions-Width)	-
8.4, 9.2 & 11.3 & Table 1 (Indivisual Compressive strength)	-
8.3 & 9.1 (Indivisual Moisture Content)	-
8.3 & 9.1 Table 1 (Indivisual Block Density)	-
8.3 (Physical requirments- Block density)	-
3.3 (Faces & Arises)	-
3.4 (Special Faces)	-

Partial

IS 10500 (2012)

Drinking water - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
TABLE 6 sl no 1 (All water intended for drinking: a) E. coli or thermotolerant coliform bacteri)	-
TABLE 6 sl no 2 (Treated water entering the distribution system: a) E. coli or thermotolerant coliform bacteria)	-
TABLE 6 sl no 3 (b) Total coliform bacteria)	-
TABLE 6 sl no 4 (Treated water in the distribution system: a) E. coli or thermotolerant coliform bacteria)	-
TABLE 6 sl no 5 (b) Total coliform bacteria)	-

Partial

IS 16232 (2014)

Iron fortified iodized salt (Double Fortified Salt) - Food grade - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Description - Iron fortified iodized salt (Double fortified salt) shall be crushed crystalline solid; white or pale pink or light grey in colour, free from contamination with clay and other extraneous adulterants and impurities)	-
3.3 (material shall pass through 4.00 mm IS sieve)	-
3.4 - Table 1 - i (Moisture - Annex A of IS 7224)	-
3.4 - Table 1 - ii (Water insoluble matter, on dry basis - A-4 of IS 253 )	-
3.4 - Table 1 - iii (Chloride content (as NaCl), on dry basis - A-4 of IS 253)	-
3.4 - Table 1 - iv (Matter insoluble in dilute HCl, on dry basis - Annex G)	-
3.4 - Table 1 - v (Matter soluble in water other than sodium chloride, on dry basis - A-6 of IS 253)	-
3.4 - Table 1 - vi (Iron content (as Fe) - Annex A)	-
3.4 - Table 1 - vii- a (Iodine content, Manufacturer’s level - Annex B)	-
3.4 - Table 1 - vii- b (Iodine content, Distribution channel including retail level - Annex B)	-
3.4 - Table 1 - viii - b (pH of 5 percent aqueous solution : For other forms of iron fortification - Annex C)	-
3.4 - Table 1 - ix (Sulphate (as SO4) - A-8 of IS 253)	-
3.4 - Table 1 - x (Magnesium (as Mg), water soluble - A-7 of IS 253)	-
3.4 - Table 1 - xi - b (Phosphorous (as P2O5) - For other forms of iron fortification - Annex D)	-
3.4 - Table 1 - xii (Sodium hexa meta phosphate, on dry basis - Annex E)	-
3.4 - Table 1 - xi - a (Phosphorous (as P2O5) - For iron fortification through encapsulated ferrous fumarate - Annex D)	-

Partial

IS 2556 : Part 16 (2002)

Vitreous sanitary appliances (Vitreous China) - Specification: Part 16 specific requirements of wash down wall mounted water closets

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
"3 IS 2556(P1)" (GENERAL REQUIREMENTS)	-
"5 Table 1 & 2 " (DIMENSIONS AND TOLERANCES)	-
7 (FINISH)	-
6.1 (CONSTRUCTION)	-
8.1 ()	-
8.2 (Smudge Test)	-
8.3 (Holding Capacity Test)	-
8.4 (Single Ball Test)	-
9 (LOAD TEST)	-
4 (PATTERNS)	-

Partial

IS 13258 (2014)

Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gas - Requirements for inspection and reconditioning of used lpg cylinders (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.4 (Tare Weight Verification)	-
14 (HYDROSTATIC TEST)	-
16 (PNEUMATIC TEST)	-

Partial

IS 14151 : Part 1 (1999)

Irrigation equipment - Sprinkler pipes - Specification: Part 1 polyethylene pipes (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3 (CLASSIFICATION OF PIPES)	-
6.1 (VISUAL APPEARANCE)	-

Partial

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2.1 (Visual and Workmanship Requirement)	-
Cl 4.1.5 (Rubber rings- C)Rubber ring shall be of black colour:)	-
Cl 4.1.5 (Rubber rings- B) Change in hardness)	-
Cl 4.1.5 (Rubber rings- A)Shore hardness (Shore-A))	-
3.0 (DIMENSIONS OF PIPE)	-
3.0 (Reversion test)	-
8 (Marking)	-
Cl 4.1.5 (Rubber rings- C)Rubber ring shall be of black colour:)	-
Cl 4.1.5 (Rubber rings- B) Change in hardness)	-
Cl 4.1.5 (Rubber rings- A)Shore hardness (Shore-A))	-
3.0 (DIMENSIONS OF PIPE)	-
3.0 (Reversion test)	-
8 (Marking)	-

Partial

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.5 (Surface colour of the pipes shall be dark shade of grey)	-
Cl.7.1 (Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.1 ( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.1 ( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-
Cl.7.2 (Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-
Cl.7.3.2 (Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-
Cl.8.1 (The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-
Cl.8.2 (When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-
Cl.8.4 (When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-
Cl.11. (Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-

Partial

IS 12395 (1988)

Specification for disposable trash bags of plastics

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

IS 7129 (2021)

POTASSIUM CARBONATE ANHYDROUS SPECIFICATION (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Description)	-
4.3 - Table 1 - Sl No - i (Total Alkalinity (as K2CO3) - Annex A 2)	-
4.3 - Table 1 - Sl No - ii (Potassium bicarbonate (as KHCO3) - Annex A 3)	-
4.3 - Table 1 - Sl No - ii (Free alkali (as KOH)- Annex A 3)	-
4.3 - Table 1 - Sl No - iii (Sulphates (as K2SO4) - Annex A 4)	-
4.3 - Table 1 - Sl No - iv (Chlorides (as KCl) - Annex A 5)	-
4.3 - Table 1 - Sl No - v (Matter insoluble in water - Annex A 6)	-
4.3 - Table 1 - Sl No - vi (Iron (as Fe) - Annex A 7 & A 12)	-
4.3 - Table 1 - Sl No - vii (Heavy metals (as Pb - Annex A 8 & A 12)	-
4.3 - Table 1 - Sl No - viii (Loss on heating at 150oC - Annex A 9)	-
4.3 - Table 1 - Sl No - ix (Sodium (as Na) - Annex A 10 & A 12)	-

Partial

IS 2556 : Part 5 (1994)

Vitreous sanitary appliances (Vitreous China) - Specification: Part 5 specific requirements of laboratory sinks

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (General requirements-Thickness IS 2556 (Part 1))	-
3 (General requirements-PERFORMANCE REQUIllEMENTS-WARPAGE IS 2556 (Part 1))	-

Partial

IS 1165 (2002)

Milk Powder (Bi-lingual)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.5 (Bacterial count)	-
3.5.2 (Coliform count)	-
3.5.3 (Staphylococcus Aureus)	-
3.5.4 (Salmonella)	-
3.5.5 (Shigella)	-
3.4.5 (Moisture)	-
3.4.5 (Total solids)	-
3.4.5 (Fat)	-
3.4.5 (Insolubility index)	-
3.4.5 (Total ash)	-
3.1 (Description)	-
3.2 (Flavour and taste)	-
3.4.5 (Titratable acidity (lactic acid))	-

Partial

IS 1656 (2007)

Milk - Cereal based complementary foods - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4' 5.1 to 5.4 (Description)	-
5.6 (Flavour and odour)	-
5.8 (Total protein)	-
5.8 (Fat)	-
5.8 (Total Ash)	-
5.8 (Acid insoluble ash)	-
5.7.1 (Bacterial count)	-
5.7.2 (Coliform count)	-
5.7.3 (Escherichia coli)	-
5.7.4 (Staphylococcus aureus)	-
5.7.5 (Salmonella and shigella)	-
5.7.6 (Yeast and mould count)	-

Partial

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1 (Colour)	-
10.1 (Surface Finish)	-
7.2.1.1 Table3 (Angle of taper (Note-1))	-
5 (CLASSIFICATION OF PIPES)	-
7 (DIMENSIONS-PIPE-Nominal Diameter)	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Minimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-
7.1.1.1 (DIMENSIONS-PIPE-Mean O.D. Variation)	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-
7.1.1.2 (DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-
7.1.1.2 (DIMENSIONS-PIPE-Ovality (Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Minimum))	-
7.1.2.1 (DIMENSIONS-PIPE-Thickness(Maximum))	-
7.1.2.1 (DIMENSIONS-PIPE-Average Thickness)	-
7.2.1 (DIMENSIONS-Socket)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-
7.2.1.1-Table 3 (DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-
7.2.1.2-Table 4 (DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-
8 (SEALING RINGS)	-
9.1 (PIPE ENDS)	-
10.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.1.1 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-
10.2 (PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-
10.4 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-
10.5 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-
10.6 (PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-
11.1-Table 6 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-
11.1-Table 7 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-
11.1.1 (MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-
11.2 (Resistance to External Blows at 0°C)	-
7.1.4 (Length)	-
10.7 (Sulphated Ash Content)	-

Partial

IS 252 (2013)

Caustic soda - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Form and Description)	-
Cl. 3.3 and 3.4(Table 1, S. no i) (Sodium carbonate (as Na2CO3), percent by mass)	-
Cl. 3.3 and 3.4(Table 1, S. no ii) (Sodium hydroxide (as NaOH), percent by mass)	-
Cl. 3.3 and 3.4(Table 1, S. no iii) (Chlorides (as Cl– ), percent by mass)	-
Cl. 3.3 and 3.4(Table 1, S. no iv) (Sulphates (as SO4), percent by mass)	-
Cl. 3.3 and 3.4(Table 1, S. no v) (Silicates (as SiO2), percent by mass)	-
Cl. 3.3 and 3.4(Table 1, S. no vi) (Iron (as Fe))	-
Cl. 3.3 and 3.4(Table 1, S. no vii) (Copper)	-
Cl. 3.3 and 3.4(Table 1, S. no viii) (Manganese)	-
Cl. 3.3 and 3.4(Table 1, S. no ix) (Chlorates and per-chlorates)	-
Cl. 3.3 and 3.4(Table 1, S. no x) (Matter insoluble water, percent by mass)	-
Cl. 3.3 and 3.4(Table 1, S. no xi) (Total mercury)	-
Cl. 3.3 and 3.4(Table 1, S. no xii) (Sodium hydroxide)	-

Partial

IS 1486 (1978)

Specification for copper oxychloride, technical

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Partial

IS 4654 (2019)

Paraffin Wax — Specification ( Third Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 Table 1 (Ash, all types)	-
4.2 Table 1 (Saponification value, all types)	-

Partial

IS 10146 (1982)

Specification for polyethylene for its safe use in contact with foodstuffs, pharmaceuticals and drinking water zy

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.4 (Overall Migration)	-

Partial

IS 17048 (2018)

Halogen free flame retardant (HFFR) cables for working voltages up to and including 1 100 Volts - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1.1 a) (Conductor : Material )	-
4.1.1 b) (Material : Seperator tape )	-
4.1.1 d) , 11.1, 12.1, 13.1,14.1 (Class of conductor )	-
4.1.1 e) (Shape of conductor )	-
4.1.1 f) (Nominal size of conductor )	-
4.2.1, 11.2, 12.2, 13.2, 14.2 (Insulation : Material )	-
4.2.2, 11.2, 12.2, 13.2, 14.2 (Insulation : Application )	-
4.2.3,11.2, 12.2, 13.2 (Thickness of insulation - Avearge : IS 10810 ( Part 6 ))	-
4.2.3, 11.2, 12.2, 13.2, 14.2 (Thickness of insulation - miniumum : IS 10810 ( Part 6 ))	-
4.2.4 (Insulation : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-
4.2.4 (Insulation : Elongation ( Before ageing) -IS 10810 (Part 7))	-
4.2.4 (Insulation : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-
4.2.5 (Insulation : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-
4.2.4 (Insulation : Elongation (after ageing) - IS 10810 (Part 7) )	-
4.2.5 (Insulation : Elongation variation (after ageing) - IS 10810 (Part 7) )	-
4.5.1,13.4, 14.4 (Sheath : Compound )	-
4.5.2, 13.4, 14.4 (Sheath : Application)	-
4.5.3,13.4, 14.4 (Thickness of sheath - Average : IS 10810 (Part 6))	-
4.5.3,13.4, 14.4 (Thickness of sheath - Minimum : IS 10810 (Part 6))	-
4.5.4, 13.4 (Sheath : Tensile stregth ( Before ageing)-IS 10810 (Part 7) )	-
4.5.4,13.4 (Sheath : Elongation ( Before ageing) -IS 10810 (Part 7))	-
4.5.4, 13.4, 14.4 (Sheath : Tensile stregth ( After ageing) - IS 10810 (Part 7) )	-
4.5.5, 13.4, 14.4 (Sheath : Tensile stregth variation ( After ageing) - IS 10810 (Part 7) )	-
4.5.4, 13.4, 14.4 (Sheath : Elongation (after ageing) - IS 10810 (Part 7) )	-
4.5.5, 13.4,14.4 (Sheath : Elongation variation (after ageing) - IS 10810 (Part 7) )	-
4.5.5, 11.3, 12.3, 13.6, 14.6 (Overall Dimensions)	-
4.5.5.1, 11.3, 12.3,13.5, 14.5 (Ovality)	-
4.5.6, 13.4 (Colour of Sheath)	-
5.1 (High Voltage Test (at Room Temperature))	-
5.3 (Flammability Test- IS 10810 (Part 53).)	-
5.12 (Hot Set Test- IS 10810 (Part 30).)	-
5.12 (Permanent Set - IS 10810 (Part 30).)	-
5.13 (Water Immersion Test (Effect of Water on Sheath) : Tensile strength -IS 10810 (Part 7).)	-
5.13 (Water Immersion Test (Effect of Water on Sheath) : Elogation -IS 10810 (Part 7).)	-
5.15 (Cold Bend Test-IS 10810 (Part 20).)	-
5.16 (Cold Impact Test- IS 10810 (Part 21).)	-
6.1, Table 1 (CORE IDENTIFICATION)	-
6.2 (Core Identification by Numbers)	-
6.2.1 (Preferred Arrangement of Marking)	-
6.2.2 (Durability)	-
7.0 (CABLE CODE)	-
9.0 ( IDENTIFICATION)	-
10.2.1 (Standards marking)	-
13.3, 14.3 (assembly of cores )	-
6.1 (General Requirements)	-
6.1.1 (Colour Combination Green Yellow)	-

Partial

IS 9857 (1990)

Welding cables - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Conductor : Material )	-
5 (SEPARATOR)	-
6 (COVERING)	-
7 (CONDUCTOR : CONSTRUCTION )	-
8 (S E P A R A T O R)	-
9.1 (C O V E R I N G : Application )	-
9.2 (T h i c k n e s s o f C o v e r i n g)	-
9.3 (T o l e r a n c e on Thickness o f C o v e r i n g)	-
9.4 (A p p l i c a t i o n of C o v e r i n g)	-
9.5 (Colour of C o v e r i n g)	-
10.1 a) 1) (Annealing test - IS 10810: Part 1)	-
10.1 a) 2) (Conductor resistance tes - IS 10810 : Part 5)	-
10.1 c) 1) (Physical tests for covering : Tensile strength )	-
10.1 c) 1) (Physical tests for covering : Elongation at break )	-
10.1 c) 2) (Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-
10.1 c) 2) (Physical tests for covering -Ageing in Air oven : Elongation at break )	-
10.1 c) 2) (Physical tests for covering - Ageing in Air oven : Tensile strength )	-
10.1 c) 2) (Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-
10.1 c) 5) (Hot set test )	-
11.1 (High Voltage Test ( Water Immersion Test ))	-
11.4 (Flammability Test)	-
12.1 (Manufacturer's Identification)	-
12.2 (Cable Identification)	-
12.3 (Cable Code)	-

Partial

IS 2593 (1984)

Flexible Cables for Miners' Cap-lamps

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (CONDUCTOR)	-
3.1.2 (Resistance test )	-
4.1 (INSULATION)	-
6.1 (SHEATH)	-
7.1 (Construction : Conductor )	-
8.1 (Thickness of Insulation - Average )	-
8.1 (Thickness of Insulation - minimum)	-
9.1 (IDENTIFICATION OF CORES)	-
10.1 (LAYING UP)	-
11.1 (SHEATH : Application )	-
11.2 (Thickness of Sheath -average )	-
12.2 (Thickness of Sheath - Minimum)	-
11.3 (Coulor of sheath )	-
12.1 (OVERALL DIAMETER)	-
13.1 b) (Annealing test)	-
13.1 e) 1) (Physical tests for insulation: Tensile strength )	-
13.1 e) 1) (Physical tests for insulation: elongation at break )	-
13.1 e) 1) (Physical tests for Sheath : Tensile strength )	-
13.1 e) 1) (Physical tests for Sheath: elongation at break )	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : Tensile Strength )	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : Tensile Strength variation )	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : elongation variation at break)	-
13.1 e) 2) (Ageing in air oven ( for insulation ) : elongation variation at break)	-
14.1 (Voltage test)	-
14.2 (Flammability test)	-
14.4 (Checking of overall diameter of cable)	-
15.1 (MANUFACTURER'S IDENTIFICATION)	-
16.2 (Marking )	-
16.2.1 (Standards Mark )	-

Partial

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

No Record Found

No Record Found

No Record Found