BIS - LIMS (Laboratory Information Management System)

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List

Reset

274 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

241

IS 398 : Part 4 (1994)

Aluminium conductors for overhead transmission purposes: Part 4 aluminium alloy stranded conductors (Aluminium - Magnesium - Silicon Type) - Specification (Third Revision)

AAAC

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Freedom from Defects)	-
7.1 Table-1 (Dimensional measurement of wires)	-
7.2.2 Table-2, Table-4 (Calculated resistance of Stranded Conductor)	-
8.1 (Joints in wires-Conductors Containing Seven Wires)	-
8.2 (Joints in wires-Conductors Containing More Than Seven Wires)	-
9.1 (Stranding)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-
9.3 (Direction of Lay)	-
9.4 (Multiple layers of wires)	-
11 (Packing and Marking)	-
12.2 Table 1 (Breaking Load Test- Before Stranding)	-
12.2 Table 1 (Breaking Load Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.3 Table 1 (Elongation Test- Before Stranding)	-
12.3 Table 1 (Elongation Test- After Stranding)	-
12.4 Table 1 (Resistance of Aluminium wire)	-
9.2 Table 3 (Lay Ratio of stranded conductors)	-

-
5 m

242

IS 11169 : Part 2 (1989)

Steels for cold heading/cold extrusion applicationsspecification: Part 2 stainless steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7 (FREEDOM FROM DEFECTS)	-
8.2, table 5 (i) Yield stess/.2% Proof stress, Mpa)	-
8.2, table 5 (ii)Ultimate Tensile Strength, Mpa)	-
8.2, table 5 (iii)Elongation, %)	-
8.2, table 5 (v)Impact strength, J)	-

-
" mech - 2 x 1 m Excluding except chemical tests

243

IS 261 (1982)

Specification for copper sulphate (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1(i) Table 1 (Copper, Tech, A-2)	-
1(ii) Table 1 (Matter insoluble in water, Tech, A-3)	-
1(iii) Table 1 (Soluble iron and aluminium compounds ( as Fe ), Tech, A-4)	-
1(iv) Table 1 (pH value, Tech, A-5)	-
1(v) Table 1 (Chloride ( as Cl ), Tech, A-6)	-
1(vi) Table 1 (Arsenic ( as As2O3 ), Tech, A-7)	-
1(vii) Table 1 (Lead and zinc, Tech, A-8)	-

-
" 500 g

244

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

Rs 6760/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Classification Heavy/Medium/L:ight)	-
5.1 (The utensil shall be pressed or spun from one piece)	-
5.2 ( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-
6.1 & Table 1 ( i) Name of Utensil )	-
6.1 & Table 1 (ii) Shape of Utensil)	-
6.1 & Table 1 (Inside dia, Φ D mm Not declared )	-
6.1 & Table 1 (Height NA)	-
6.1 & Table 1 (Capacity, l NA)	-
6.1 ( Minimum sheet thickness for nominal size )	-
7.1 (HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-
7.2 (Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-
8.1 (The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-
8.2 (The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-
8.4.1.2 ( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-
8.4.2 (A coating of thickness 25 to 100 microns is generally required)	-
8.4.3 (Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-
8.4.4 (The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-
9 (The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-
10 (Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-

-
" 2 nos Excluding Excl. Tests for Non-stick Coating and tests for lunch boxes cl. 8.6.,no chemical tests

245

IS 6452 (1989)

High alumina cement for structural use - specification (First Revision)

Testing charges for the product are: 3,700.00 Testing View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2 (Fineness IS 4031(Part 2))	-
4.3 (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-
4.4 (Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-
4.4 (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
4.5 (Compretsive Strenqth .24 hrs ± 30min IS 4031(Part 6))	-
4.5 (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
4.1 (Total alumina content (Al2O3) - Cl 4.6 of IS 4032:1985)	-

-
" 8 kg + 500 g " Excluding chem facility not available.

246

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

Rs 26700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (MATERIALS : CONDUCTOR)	-
4.1.1 (INSULATION : General Purjose Insulaiion)	-
4.1.2 (INSULATION : Heat Resisting Insulation)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
5.2 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
6.2 (MATERIALS : ARMGURING)	-
7.1.1 (OUTER SHEATH : For Cables with General Purpose InsuIafion)	-
7.1.2 (OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.1 (INSULATION )	-
9.2 (INSULATION : Thickness of Insulation)	-
9.3 (INSULATION :Tolerance on Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.3.1 (Arrangement of Marking)	-
11.1 (LAYING UP OF CORES)	-
11.2 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
12.3.1 (INNER SHEATH :Thickness of Inner Sheath)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.1.4 (ARMOURING : Application)	-
13.2 (ARMOURING : Type of Armour)	-
13.2.1 (ARMOURING : Type of Armour)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.4 (ARMOURING : Joints)	-
13.5.1 (ARMOURING : Resistance)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.1 (OUTER SHEATH)	-
14.2 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage - Crack observed )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage - Crack observed )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1 e) (Insulation resistance test : Volume Resistivity )	-
15.1 e) (Insulation resistance test : IR Constant )	-
15.1 f) (High voltage test ( water immersion test ))	-
15.1 g) (High voltage test at room temperature)	-
16.1 (DETAILS OF TESTS : General)	-
16.2 (DETAILS OF TESTS : High Voltage Test at Room Temperature)	-
16.3.1 (High Voltage Test ( Water Immersion Test ) : a.c. Test)	-
16.3.2 (High Voltage Test ( Water Immersion Test ) : d.c. Test)	-
16.4 (Flammability Test)	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.2.1 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
16.4 (Flammability Test)	-
13.6 f) (ARMOURING: Mass of zinc coating )	-

-
" 15m Excluding Except improved fire performance test for C1,C2 category(Optional tests)

247

IS 10325 (2000)

Square tins - 15 kg/litre for ghee, vanaspati, edible oils and bakery shortenings - Specification (Second Revision)

3700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions and Tolerances)	-
4.2.2 (Handle)	-
5.1 (Air-Pressure Test)	-
5.3 (Hydraulic Pressure Test)	-
5.2 (Handle Pull Test)	-
4.1 (Dimensions and Tolerances)	-
4.3.1 (Manufacture)	-
4.3.2 (Manufacture)	-
4.3.4 (Manufacture)	-
4.3.5 (Handle)	-
4.3.5 (Handle)	-
4.3.5 (Handle)	-
4.3.5 (Handle)	-

-
" 3 Nos. " Excluding Chemical facility(tin Coating test) not available.

248

IS 15962 (2012)

Structural steels for buildings and structures with improved seismic resistance

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Freedom from Defects)	-
Cl 10 (Tensile Test)	-
Cl 11 (Impact Test)	-
Cl 13 (Dimensions)	-
Cl 13 (Dimensions)	-
Cl 13 (Dimensions)	-
Cl 13 (Dimensions)	-

-
" 1.5 m " Excluding except tensile test for the samples of diameter above 20 mm and chemical tests; (Prepared test pieces are required for Impact test)

249

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

Rs.750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Freedom from defects)	-
8.2 (Width)	-
8.2 (Thickness)	-
9.1 (Finishing & Packing)	-

-
" 0.5 sq.m Excluding except tensile, bend test and chemical tests

250

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 12 (Workmanship)	-
Cl 13 (Length, Width & Thickness)	-

-
" 2x0.5 mt " Excluding Excl cupping test, Bend test (as lower sizes of manderls is not available), Strain aging test and chemical requirements

251

IS 1011 (2002)

Biscuits - Specification (Fourth Revision)

Rs.3280/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (General Requirement)	-
6.3 Table 2 i (Moisture)	-
6.3 Table 2 ii (Acid insoluble ash (on dry basis))	-
6.3 Table 2 i (Moisture)	-
6.3 Table 2 ii (Acid insoluble ash (on dry basis))	-

-
" 3 x 100 g Excluding determination acidity of extractable fat

252

IS 1417 (2016)

Gold and gold alloys, jewellery/ artefacts - Fineness and marking - Specification (Fourth Revision)

Rs.1800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Fineness/ Gold Content in parts per thousand, percent)	-
4.1.1 (a) (Presence of Iridium)	-
4.1.1 (a) (Presence of Ruthenium)	-
4.1.1 (a) (Presence of Cadmium)	-
4.1.1 (a) (Presence of Osmium)	-

-
" 1 gm

253

IS 17423 (2020)

Medical textiles – Coveralls for COVID 19 – Specification

Rs.3650/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Manufacture - IS 17423)	-
4.1.1 (Manufacture - IS 17423)	-
4.1.1 (Manufacture - IS 17423)	-
4.2 (Manufacture - IS 17423)	-
4.2 (Manufacture - IS 17423)	-
4.3 (Manufacture - IS 17423)	-
4.3 (Manufacture - IS 17423)	-
4.4 (Manufacture - IS 17423)	-
4.4 (Manufacture - IS 17423)	-
4.5 (Manufacture - IS 17423)	-
4.6 (Manufacture - IS 17423)	-
5.1 (Workmanship and Finish - IS 17423)	-
5.1 (Workmanship and Finish - IS 17423)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric from body Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric from body Specimen 2)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric from body Specimen 3)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric at Seam Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric at Seam Specimen 2)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Coverall Fabric at Seam Specimen 3)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover Fabric from body Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover Fabric from body Specimen 2)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover Fabric from body Specimen 3)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover of Seam Specimen 1)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover of Seam Specimen 2)	-
Table 1 & Cl.4.4, 5.2 and 5.3) (Blood Resistance Characteristics (Proceduce-C, table 1 IS 16546:2016) Shoe Cover of Seam Specimen 3)	-

-
-

254

IS 15354 : Part 1 (2018)

Single - Use medical examination gloves: Part 1 specification for gloves made from rubber latex or rubber solution (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 & Table 2 (Size code)	-
6.1 & Table 2 (Width corresponding to size code (dimension w,Figure 1))	-
6.1 & Table 2 (Descriptive size)	-
6.1 & Table 2 (Width corresponding to Descriptive size (dimension w,Figure 1))	-
6.1 & Table 2 (Minimum length (dimension l, Figure 1))	-
6.1 & Table 2 (Minimum thickness (at locations shown in Figure 2))	-
6.1 & Table 2 (Maximum thickness (at approximate centre of palm))	-
6.3.2 & Table 3 (Minimum force at break before accelerated ageing)	-
6.3.2 & Table 3 (Minimum Elongation at break before accelerated ageing)	-
6.3.3 & Table 3 (Minimum force at break after accelerated ageing)	-
6.3.3 & Table 3 (Minimum Elongation at break after accelerated ageing)	-

-
" Mech - 10 pairs

255

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 & Table 3 (UTM)	-
Cl 11 (Workmanship)	-
Cl 12 & 13 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
7.1 (Silicon %)	-
7.1 ( Copper %)	-
7.1 ( Aluminium %)	-
7.1 ( Nb)	-
7.1 (V)	-
7.1 ( Ti)	-
7.1 (Cr)	-
7.1 (Mo)	-
7.1 (Ni)	-
7.1 ( Nitrogen%)	-
Table 1 ( Clauses 7.1 ,7.2 ) (CARBON EQUIVELENT )	-
7.0 (7) (Micro Alloying elements - IS:8811)	-
Table 1 ( Clauses 7.1 ,7.2 ) (Tungsten (W))	-
Table 1 ( Clauses 7.1 ,7.2 ) (Boron (B))	-

-
" 0.5 sq.m Chemical Facility is available Quantity: 5 Pieces of 5cm X 5cm Excluding Bend test not available(Prepared test pieces are required for Tensile Test)

256

IS 3074 (2013)

Steel tubes for automotive purposes - Specification (Third Revision)

4200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Workmanship)	-
8.2,15,17,22, Table 3,5 &7 (Tensile Tests,IS 1608 Part 1)	-
8.3,18, (Flattening Test)	-
8.4 (Crushing Test)	-
8.5 (Drift Test)	-
6 (STRAIGHTNESS)	-
8.2,15,17,22, Table 3,5 &7 (Tensile Tests,IS 1608 Part 1)	-

-
" 2 mt + 50gm Excluding except LEAK TIGHTNESS TEST,chemical tests

257

IS 963 (1958)

Specification for chrome molybdenum steel bars and rods for aircraft purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Freedom from defects)	-
7.5 (Hardness)	-
7.6.2 (i) Yield stess/.2% Proof stress, Mpa)	-
7.6.2 (ii)Ultimate Tensile Strength, Mpa)	-
7.6.2 (iii)Elongation, %)	-
7.6.2 (ii)Ultimate Tensile Strength, Mpa)	-
9 (Rolling Tolerances)	-

-
" mech - 2 x 500 mm " Excluding except Hardenability, Grain size, Decarburization and Chemical tests

258

IS 13428 (2005)

Packaged natural mineral water specification (Second Revision)

19200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1.1 (Escherichia coli(or thermotolerant bacteria))	-
6.1.2 (Coliform , bacteria)	-
6.1.3 (Faecal Streptococci )	-
6.1.3 (Staphylococcus Aureus)	-
6.1.4 (Sulphite Reducing Anaerobes )	-
6.1.5 (Pseudomonas Aeruginosa )	-
6.1.6 (Yeast and Mould )	-
6.1.7 (Salmonella )	-
6.1.7 (Shigella)	-
6.1.8 (Vibrio cholera )	-
6.1.8 (Vibrio parahemolyticus)	-
6.2 Table-1 i (Colour)	-
6.2 Table-1 ii (Odour)	-
6.2 Table-1 iii (Taste)	-
6.2 Table-1 iv (Turbidity)	-
6.2 Table-1 v (Total dissolved solids)	-
6.2 Table-1 vi (pH)	-
6.2 Table-2 i (Nitrate (as NO3))	-
6.2 Table-2 ii (Nitrite (as NO2))	-
6.2 Table-2 iii (Sulphide (as H2S))	-
6.2 Table-2 iv (Manganese (as Mn))	-
6.2 Table-2 v (Copper (as Cu))	-
6.2 Table-2 vi (Zinc (as Zn))	-
6.2 Table-2 vii (Flouride (as F))	-
6.2 Table-2 viii (Barium (as Ba))	-
6.2 Table-2 ix (Antimony (as Sb))	-
6.2 Table-2 xi (Silver (as Ag))	-
6.2 Table-2 xii (Chloride (as Cl))	-
6.2 Table-2 xiii (Sulphate (as SO4),)	-
6.2 Table-2 xiv (Magnesium (as Mg))	-
6.2 Table-2 xv (Calcium (as Ca))	-
6.2 Table-2 xvi (Sodium (as Na))	-
6.2 Table-2 xvii (Alkalinity (as HCO3))	-
6.2 Table-2 xviii (Selenium (as Se))	-
6.2 Table-2 xix (Mineral Oil)	-
6.2 Table-2 xx (Phenolic compounds (as C6H5OH))	-
6.2 Table-3 i (Arsenic (as As))	-
6.2 Table-3 ii (Cadmium (as Cd))	-
6.2 Table-3 iv (Chromium (as Cr))	-
6.2 Table-3 v (Mercury (as Hg))	-
6.2 Table-3 vi (Lead (as Pb)	-
6.2 Table-3 vii (Nickel (as Ni))	-

-
" 48x500ml; 24x1 ltr; 6x2ltr; 4x5 ltr; 2x20ltr Excluding ex.for radio active residues , CN,mbas,Phenolic compounds

259

IS 459 (1992)

Corrugated and semi - Corrugated asbestos cement sheets - Specification (Third Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1 (Dimensions & Tolerances - Type of Sheet - cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Depth of Corrugation, D - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Pitch of Corrugation, P - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Overall width, B - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Effective Width, C - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Nominal Thickness, T - Cl. 5)	-
5, Table 1, Figure 1,2 (Dimensions & Tolerances - Length of Sheet, A - Cl. 5)	-
6.1 (Load Bearing Capacity Test - Cl. 6.1, IS 5913)	-
7 (General Appearance and Finish - Cl. 7.1)	-
7 (General Appearance and Finish - Cl. 7.2)	-
12 (Marking - Indication of source of manufacture - Cl. 12)	-
12 (Marking - Year & Date of manufacture - Cl. 12)	-
12 (Marking - Pictorial warning signs as given in IS 12081 (Part 2) : 1987 - Cl. 12)	-

-
" 03 nos. " Excluding optional tests,colouring matter

260

IS 13422 (1992)

Disposable surgical rubber gloves specification

Rs.6900.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.4 (Sterility)	-
4 (TYPES)	-
5.2.1 (General Characteristics and Dimensions)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Length)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Width)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Finger)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Palm)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Cuff)	-
5.3 and Table 2 ( Tensile Strength Before Ageing)	-
5.3 and Table 2 ( Elongation at Break Before Ageing)	-
5.3 and Table 2 (Stress at 500% Elongation at Break Before Ageing)	-
5.3 and Table 2 ( Tensile StrengthAfter Accelerated Ageing)	-
5.3 and Table 2 ( Elongation at Break After Accelerated Ageing)	-
5.5 (Airtight Test)	-

-
" Mech - 25 pairs, Micro - 3 pairs "

261

IS 13334 : Part 2 (2014)

Skimmed milk powder - Specification: Part 2 extra grade (First Revision)

EXTRA GRADE

10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (ix) (Bacterial count (IS 5402))	-
Table 1 (x) (Coliform count (IS 5401 - Part 1))	-
Table 1 (xi) (Escherichia coli (IS 5887 - Part 1))	-
Table 1 (xii) (Coagulase positive Staphylococcus aureus (IS 5887 - Part 2))	-
Table 1 (xiii) (Salmonella (IS 5887 - Part 3))	-
Table 1 (xiv)(a) (Spore Count: a)Aerobic (Bacillus cereus) Type m (IS 5887 - Part 6))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type m (ISO 15213 : 2003))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type M (ISO 15213 : 2003))	-
Table 1 (xv) (Listeria monocytogenes (IS 14988 - Part 2 : 2001))	-
Table 1 (i) (Moisture (IS 116231or 16072))	-
Table 1 (ii) (Milk protein in milk solids not fat (IS 72192))	-
Table 1 (iii) (Milk fat (IS 117213) or Annex B)	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (v) (Total ash (on dry basis), Annex B of IS 14433)	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (viii) (Scorched particles (equivalent to Disc B) (IS 13500))	-

-
2X500g Excluding Except Lactate Content

262

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

Rs.6450.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.6 (Vicat Softening Temperature IS 12235 (Part 2).)	-
9.3 (Density IS 12235 (Part 14))	-
9.1 ( Visual Appearance)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Min)	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B (Mean outside dia over connection,mm (Take 4 reading and maximum valu reported))	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Outer Diameter at any point )	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe, Min)	-
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B (Mean Outer Diameter of Pipe)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe , Max)	-
7.1, 7.2 and Table 5, 6 & 7 Fig 1B (Outer Diameter at any point , Min)	-
8.4 (Sealing rings - Hardness)	-
9.1 ( Visual Appearance)	-
5 (COLOUR)	-
8.4.1 and Table 13 Fig 3B & 4B (Dimensions of sealing elements)	-
7.4 Table 8 & 9 Fig 1 (Effective length, l2)	-
7.4 Table 8 & 9 Fig 1 (Segmental length, l3)	-
7.4 Table 8 & 9 Fig 1 (Segmental length,mm for socket (average of 4.0))	-
7.4 Table 8 & 9 Fig 1 (Segmental length for Spigot (average of 4.0))	-
7.3.1 (No.of Ribs)	-
7.3.2 (Rib height)	-

-
" 6 mts, 2 Gaskets and 5 Hardness button Excluding Excl. Tensile test, reistance to external blows at 0°C , Effect on Water, thread gauges

263

IS 8249 (2019)

Zinc sulphate heptahydrate, agricultural grade - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
(Clauses 3.2 and 6.2) Table 1 (Matter insoluble in water)	-
(Clauses 3.2 and 6.2) Table 1 (Zinc (as Zn))	-
(Clauses 3.2 and 6.2) Table 1 (Lead (as Pb))	-
(Clauses 3.2 and 6.2) Table 1 (Copper (as Cu))	-
(Clauses 3.2 and 6.2) Table 1 (Magnesium (as Mg))	-
(Clauses 3.2 and 6.2) Table 1 (pH)	-
(Clauses 3.2 and 6.2) Table 1 (Cadmium (as Cd))	-
(Clauses 3.2 and 6.2) Table 1 (Arsenic (as As))	-
(Clauses 3.2 and 6.2) Table 1 (Sulphur (as S))	-

-
-

264

IS 455 (2015)

Portland slag cement - Specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 - Table - 1 i (Insoluble residue - Cl 6.9 of IS 4032:1985)	-
6 - Table - 1 ii (Magnesia - Cl 6.8 of IS 4032:1985)	-
6 - Table - 1 iii (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 6.11 of IS 4032:1985)	-
6 - Table - 1 v (Loss on ignition - Cl 6.2 of IS 4032:1985)	-
6 - Table - 1 vi (Chloride content - Cl 4.13 of IS 4032:1985)	-
7 Table 1 iv c (Compretsive Strenqth 672 ± 4 hr IS 4031(Part 6))	-
7 Table 1 iv b (Compretsive Strenqth 168 ± 2 hr IS 4031(Part 6))	-
7 Table 1 iv a (Compretsive Strenqth .72 ± 1 hr IS 4031(Part 6))	-
7 Table 1 iii b (Setting Time ( by Vicat Apparatus ), Final IS 4031(Part 5))	-
7 Table 1 iii a (Setting Time ( by Vicat Apparatus ),Initial IS 4031(Part 5))	-
7 Table 1 ii b (Soundness, Autoclave expansion IS 4031(Part 3) )	-
7 Table 1 ii a (Soundness, Le-Chate1ier expansion IS 4031(Part 3) )	-

-
" 8 kg+300gm Excluding Except for Transverse strength (Optional test), Requirement for testing Alkali Content may be specifically mentioned.

265

IS 8042 (2015)

White portland cement - Specification (Third Revision)

Rs 12050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 - Table - 1 i (Ratio of percentage of lime to percentages of silica, alumina and iron oxide - Cl 4 of IS 4032:1985)	-
5 - Table - 1 ii (Iron oxide - Cl 4.5 of IS 4032:1985)	-
5 - Table - 1 iii (Insoluble residue - Cl 4.10 of IS 4032:1985)	-
5 - Table - 1 iv (Magnesia - Cl 4.8 of IS 4032:1985)	-
5 - Table - 1 v (Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 4.9 of IS 4032:1985)	-
5 - Table - 1 vi (Loss on ignition - Cl 4.2 of IS 4032:1985)	-
5 - Table - 1 vii (Chloride content - Cl 4.13 of IS 4032:1985)	-
6 -Table 2- i (Fineness 4031 Part 2)	-
6 -Table 2- ii- a (Expansion by Le Chatelier- 4031 Part 3)	-
6 -Table 2- ii- b (Expansion by Autoclave- 4031 Part 3)	-
6 -Table 2- iii- a (Setting Time Initial- 4031 Part 5)	-
6 -Table 2-iii- b (Setting Time Final- 4031 Part 5)	-
6 -Table 2- iv- a (Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-
6 -Table 2- iv- b (Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-
6 -Table 2- iv- c (Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-

-
" 8 kg + 500 g Excluding Other than Transverse strength (Optional)

266

IS 651 (2007)

Glazed stoneware pipes and fittings - Specification (Sixth Revision)

Rs. 6850/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 7.4 (Acid Resistance Test)	-
Clause 7.5 (Alkali Resistance Test)	-
7.2 (Hydraulic Test)	-
7.3 (Absorption Test)	-
10.1-Table 1 (INTERNAL DIAMETER)	-
11.1-Table 1 ( Mean Thickness of Barrel and of Socket)	-
14-Table 1 (Internal Depth of Socket)	-
14-Table 3 (Length of Grooving of Spigot)	-
14 (The interior of the sockets shall be conical, having a minimum taper)	-
5.1 (GENERAL QUALITY)	-
5.1 (GENERAL QUALITY)	-
5.2(a) (GENERAL QUALITY)	-
5.2(b) (GENERAL QUALITY)	-
5.2(c) (GENERAL QUALITY)	-
6 ( GLAZING)	-
7.3 (Absorption Test)	-
14-Table 2 (Excess Shoulder Measurment)	-
14-Table 3 (Length of Grooving of Spigot)	-
12.2 (STRAIGHTNESS OF BARRELS OR STRAIGHT AND TAPER PIPES-Length of Junction)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-Internal Diameter)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-r)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-a)	-
13.1-Table 2 (Dimensions of One-Quarter Bends-angle)	-
13.1-Table 3 (Dimensions of One-Eighth Bends--Internal Diameter)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-r)	-
13.1-Table 3 (Dimensions of One-Eighth Bends-angle)	-
13.1-Table 4 (Dimension of One-Sixteenth Bends-Internal Diameter)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-d)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-D)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-r)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-a)	-
13.1-Table 5 (Dimension of One-Quarter Taper Bends-Angle)	-
13.1-Table 6 (Dimensions of One-Eighth Taper Bends-d)	-
13.1-Table 6 (Dimensions of One-Eighth Taper Bends-D)	-
13.2 (The angle at junction)	-
14 (The interior of the sockets shall be conical, having a minimum taper)	-
15 (GROOVING Length)	-
15 (GROOVING Depth)	-
17-Table 7 (Dimensions of Half-Section One-Quarter Channel Bends-Internal Diameter)	-
17-Table 7 (Dimensions of Half-Section One-Quarter Channel Bends-r)	-
17-Table 7 (Dimensions of Half-Section One-Quarter Channel Bends-a)	-
17-Table 7 (Dimensions of Half-Section One-Quarter Channel Bends-Angle)	-
17-Table 8 (Dimensions of Half-Section One-Eighth Channel Bends-Internal Diameter)	-
17-Table 8 (Dimensions of Half-Section One-Eighth Channel Bends-Angle)	-
17-Table 9 (Dimensions of Half-Section One-Sixteenth Channel Bends-Internal Diameter)	-
17-Table 10 (Dimensions of Channel Interceptors-Internal Diameter)	-
17-Table 10 (Dimensions of Channel Interceptors-A)	-
17-Table 10 (Dimensions of Channel Interceptors-B)	-
17-Table 10 (Dimensions of Channel Interceptors-C)	-
17-Table 10 (Dimensions of Channel Interceptors-D)	-
17-Table 10 (Dimensions of Channel Interceptors-E)	-
17-Table 10 (Dimensions of Channel Interceptors-F)	-
17-Table 10 (Dimensions of Channel Interceptors-G)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-Type)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-Size)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-A)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-C)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-d)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-D)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-D')	-
17-Table 11 (Dimensions of Round Mouth Gully traps-E)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-F)	-
17-Table 11 (Dimensions of Round Mouth Gully traps-F')	-
17-Table 11 (Dimensions of Round Mouth Gully traps-G)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-Type)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-Size)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-A)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-C)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-d)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-D)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-D')	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-E)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F)	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-F')	-
17-Table 12 (Dimensions of Square Mouth Gully Traps-G)	-

-
" 2 x 2 nos. Excluding Hydrostatic test facility upto 300mm

267

IS 4246 (2002)

Domestic gas stoves for use with liquefied petroleum gases - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.24(Annexure E) (on no account the carbon monoxidel carbon dioxide ratio of the exhaust gases of any burner. operating at any consumption at which the burner is stable at gas inlet pressure from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2), exceed 0.02.)	-
Cl.23 (There shall be no extinction of the flames on any of the burners operating at maximum consumption when the appliance is placed in a general (not localized) current of air with a velocity of 2 m/s, as measured with a rotating vane anemometer. The location of the appliance relative to neighboring walls and the direction of the draught shall be varied to correspond to likely conditions of appliance installation. This applies for all pressures from 2452 kN/m2 to 3432 kN/m2 (25 gf/cm2 to 35 gf/cm2).)	-

-
-

268

IS 13334 : Part 1 (2014)

Skimmed milk powder - Specification: Part 1 standard grade (Second Revision)

10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.4 (The flavour of the product or of the reconstituted milk shall be pleasant and clean (see IS 10030).)	-
4 (Description)	-
5.6 (Moisture)	-
5.6 (Milk protein in milk solids not fat)	-
5.6 (Milk fat)	-
5.6 (Insolubility index)	-
5.6 (Milk fat)	-
5.6 (Total ash (on dry basis))	-
5.6 (Titratable acidity (lactic acid))	-
5.6 (Scorched particles)	-
5.6 (Bacterial count)	-
5.6 (Coliform count )	-
5.6 (Escherichia coli)	-
5.6 (Coagulase positive Staphylococcus aureus)	-
5.6 (Salmonella)	-
5.6 (Spore count, Aerobic (Bacillus cereus))	-
5.6 (Spore count, Anaerobic (Sulfite reducing Clostridia))	-
5.6 (Listeria monocytogenes)	-

-
" 2x500g

269

IS 12786 (1989)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 and Table 1 (DIMENSIONS OF PIPES - outside diameters)	-
5 and Table 1 (DIMENSIONS OF PIPES - wall thickness shall)	-
7.2 (Reversion Test)	-

-
" 5m pc " Excluding excl hydraulic characteristics, Susceptibility to env stress cracking test, tensile test and Chem (material) test facility not available.

270

IS 7224 (2006)

Iodized salt, vacuum evaporated iodized salt and refined iodized salt - Specification (Second Revision)

Iodized salt, vacuum evaporated iodized salt & refined

Rs7440/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2 (Particle Size)	-
Clause 4.3 Table 1 (Moisture content)	-
Clause 4.3 Table 1 (water insoluble matter)	-
Clause 4.3 Table 1 (Chloride Content(as Nacl))	-
Clause 4.3 Table 1 (Matter soluble in water other than sodium chloride)	-
Clause 4.3 Table 1 (Calcium (as Ca))	-
Clause 4.3 Table 1 (Magnesium (as mg))	-
Clause 4.3 Table 1 (Sulphate (as SO4 ),)	-
Clause 4.3 Table 1 (Iodine content, a) Manufacturers Level )	-
Clause 4.3 Table 1 (b) Distribution channel including retailer)	-
Clause 4.3 Table 1 (Alkalinity (as Na2CO3),)	-
Clause 4.3 Table 1 (Lead as (Pb))	-
Clause 4.3 Table 1 (Arsenic(as As))	-
Clause 4.3 Table 1 (Iron(as Fe))	-
Clause 4.3 Table 1 (Lead as (Pb))	-
Clause 4.3 Table 1 (Arsenic(as As))	-
Clause 4.3 Table 1 (Iron(as Fe))	-
Clause 4.2 (Particle Size)	-
4.4 (Anticaking agents (Potassium Ferrocyanide))	-
Clause no4.1 (Description)	-

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Southern Regional Laboratory (SRL)

IV CROSS ROAD, CIT CAMPUS, TARAMANI, CHENNAI-600113, TAMILNADU, CHENNAI, Chennai, Tamil Nadu, 600113

- srol@bis.gov.in

Scope List