BIS - LIMS (Laboratory Information Management System)

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List

Reset

282 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

271

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe, Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter of Pipe , Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Outer Diameter at any point , Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Outer Diameter at any point, Max)	-
7.2 and Table 5, 6 & 7 Fig 1B (Mean Outer Diameter over Connection)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Min)	-
7.2 and Table 5, 6 & 7 Fig 1B (Wall thickness, Max)	-
7.4 Table 8 & 9 Fig 1 (Segmental length, l3)	-
9.3 (Density IS 12235 (Part 14))	-
9.5 (Tensile Strength IS 12235(Part 13))	-
9.6 (Vicat Softening Temperature IS 12235 (Part 2).)	-
7.4 Table 8 & 9 Fig 1 (Effective length, l2)	-
7.4 Table 8 & 9 Fig 1 (Segmental length, l4)	-
7.4 Table 8 & 9 Fig 1 (Segmental length, l5)	-
9.5 (Tensile Strength IS 12235(Part 13))	-
8 (Marking)	-

Partial

Remark 1: For measurement of the shore hardness of the sealing ring prepared button piece is required. Remark 2 : The following test facilities are not available: (1) For Outside Diameter above 250 mm, (2) Effect on water (3)Resistance to external blow

272

IS 398 : Part 2 (1996)

Aluminium conductors for overhead transmission purposes - Specification: Part 2 aluminium conuuctors, galvanized steel - Reinforced (Third Revision)

Up to 100 sq mm

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
10 (elec) (Stranding)	-
13.4.2 (elec) (Ductility by Elongation Test before stranding)	-
13.4.2 (elec) (Ductility by Elongation Test after stranding)	-
13.6 (elec) (Resistance test-Aluminium wire before Stranding)	-
13.6 (elec) (Resistance test-Aluminium wire after stranding)	-
13.9 (elec) (Surface condition test)	-
13.10 (elec) (Ultimate breaking load)	-
13.11 (elec) (Stress-strain test)	-
13.8 Table-4 (elec) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.8 Table-4 (elec) (Lay Ratio- Steel Core (6 Wire Layer))	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Innermost Layer of Conductors with 3 Aluminium Wire Layers)	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Layer Immediately Beneath Outermost Layer)	-
13.8 Table-4 (elec) (Lay Ratio- Aluminium Wire Outermost Layer)	-
13.7.2 (elec) (Uniformity of Zinc coating)	-
13.7.2 (elec) (Mass of Zinc coating)	-
13.5.2 (elec) (Wrapping Test Galvanized Steel Wires After Stranding)	-
13.5.2 (elec) (Wrapping Test Galvanized Steel Wires Before Stranding)	-
13.5.1 (elec) (Wrapping Test Aluminium Wires After Stranding)	-
13.5.1 (elec) (Wrapping Test Aluminium Wires Before Stranding)	-
13.4.1 (elec) (Ductility by Torsion Test after stranding)	-
13.4.1 (elec) (Ductility by Torsion Test before stranding)	-
13.3 Table 2 (elec) (Breaking Load of Steel Wires After Stranding)	-
13.3 Table 2 (elec) (Breaking Load of Steel Wires Before Stranding)	-
13.3 Table 1 (elec) (Breaking Load of Aluminium Wires After Stranding)	-
13.3 Table 1 (elec) (Breaking Load of Aluminium Wires Before Stranding)	-
8.1.1 & 13.2 Table 2 (elec) (Diameter of Steel Wires After Stranding)	-
8.1.1 & 13.2 Table-1 (elec) (Diameter of Aluminium Wires After Stranding)	-
8.1.1 & 13.2 Table 2 (elec) (Diameter of Steel Wires Before Stranding)	-
8.1.1 & 13.2 Table-1 (elec) (Diameter of Aluminium Wires Before Stranding)	-

Partial

Test facility not available for Cl. 13.9, 13.10 and 13.11 for size 100 sq.mm and above.

273

IS 3854 (1997)

Switches for domestic and similar purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10 (Protection against Electric Shock)	-
11.1 (Provision for earthing)	-
12.2.3 (Mechanical strength of terminals)	-
12.2.4 (Resistance to corrosion)	-
12.2.5 (Undue damage to conductor)	-
12.2.7 (Insertion of conductor)	-
12.2.11 (Distance between screw and conductor)	-
12.3.2 (Screwless terminals)	-
12.3.4 (Material of terminals)	-
12.3.11 (vi) Electrical & Thermal Stresses [Cl 12.3.11])	-
12.3.12 (vii) Deflection Stresses [Cl. 12.3.12])	-
13.15 (q) Requirements for membrane in inlet opening [ Cl. 13.15])	-
15.1 (Resistance to Ageing, to Harmful Ingress of water and to Humidity [Cl. 15]: Resistance to Ageing, [Cl. 15.1])	-
15.2 (b)Resistance to Harmful ingress of water [Cl. 15.2])	-
15.3 (c) Resistance to Humidity [Cl. 15.3])	-
16.1 (Insulation resistance [Cl. 16.1])	-
16.2 ( Electric Strength [Cl. 16.2])	-
17 (Temperature- rise [Cl. 17])	-
19 (Normal Operation [Cl. 19] a) General & Operation)	-
19 (b) Electric Strength)	-
19 (c)Temperature-rise )	-
19.2 (Normal Operation (For AX type Switches) [Cl. 19.2])	-
20 (Mechanical Strength Test [Cl. 20])	-
21 (Resistance to Heat [Cl.21])	-
22 (Screw, Current Carrying Part And Connection [Cl.22])	-
23.2 (Creepage distances, clearances and distance through sealing compound [Cl.23])	-
24.1.1 (Resistance to Abnormal Heat & Fire [Cl.24.1] [Glow Wire Test] [Cl.24.1.1])	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8 (Marking)	-
8.9 (Marking)	-
8 (Marking)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
7 (Classification)	-
12 (Terminals)	-
12.2.1 (Terminals)	-
12 (Terminals)	-
12.2.2 (Connection of conductor)	-
12.2.7 (Insertion of conductor)	-
12.2.9 (Locking against accidental loosening)	-
12.3.2 (Screwless terminals)	-
12.3.3 (Connectin of conductor)	-
12.3.4 (Material of terminals)	-
12.3.5 (Clamping)	-
12.3.7 (v) Interconnection of conductors [Cl. 12.3.7])	-
13.1 (a) Insulating lining, barriers and the like [Cl 13.1])	-
13.2 (b) Construction of switch [Cl 13.2])	-
13.2 (i) Installation Test)	-
13.3 (c) Covers,cover plates and actuating members [Cl 13.3])	-
13.4 (d) Ordinary switches [Cl 13.4])	-
13.5 (e) Rotary switches [Cl 13.5])	-
13.6 (f) Screws and other means [Cl 13.6])	-
12.3.7 (v) Interconnection of conductors [Cl. 12.3.7])	-
13.8 (h) Assessories combined with switches [Cl. 13.8])	-
13.9 (j) Switches other than ordinary switches [Cl. 13.9])	-
13.9 (j) Switches other than ordinary switches [Cl. 13.9])	-
13.1 (k) Switches to be installed in a box [Cl. 13.10])	-
13.12, 13.13, 13.14 (m) Inlet opening [Cl. 13.12.13.13 & 13.14])	-
13.15 (q) Requirements for membrane in inlet opening [ Cl. 13.15])	-
13.15 (q) Requirements for membrane in inlet opening [ Cl. 13.15])	-
14 (Mechanism [Cl. 14])	-
14.4 (Mechanism)	-
8 (Marking)	-
8 (Marking)	-
14.4 (Mechanism)	-
14.3 (d)Test for arcing and sparking [Cl 14.3])	-
21 (Resistance to Heat [Cl.21])	-
21 (Resistance to Heat [Cl.21])	-
23 (Creepage distances, clearances and distance through sealing compound [Cl.23])	-
24.2 (Resistance to tracking [For Switch other than ordinary] [Cl.24.2])	-
19.2 (Normal Operation (For AX type Switches) [Cl. 19.2])	-
22.1 (i) Screw & Nuts [Cl.22.1])	-
22.3 (iii) Electrical Connections [Cl.22.3])	-
22.4 (ii) Screw & rivets [Cl . 22.4])	-
22.5 (iv) Current carrying part [Cl.22.5])	-
18 (Marking and breaking Capacity[Cl. 18])	-
7 (Classification)	-
7 (Classification)	-
6.1 (Ratings)	-
6.2 (Ratings)	-
25 (Resistance to Rusting)	-

Partial

Complete TF is available for variety upto and including 20A. For above 20A rating (32A, 63A), the following facilities are not available: 1. Cl 17 Temperature rise 2. Cl 18, Making and breaking Capacity 3. Cl 19 Normal Operation"

274

IS 694 (2010)

Polyvinyl chloride insulated unsheathed and sheathed cables/cords with rigid and flexible conductor for rated voltages up to and including 450/750 v (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
table 1 e) 3) (IR constant- Room temp )	-
table 1 e) 3) (IR constant- max. Temp)	-
10.2 (HV (room temperature))	-
10.1 (HV (water immersion))	-
Table 1 iii) d) 9) (Cold impact for sheath)	-
Table 1 iii) d) 8) (Cold bend for sheath)	-
Table 1 iii) c) 9) (Cold impact for insulation)	-
Table 1 iii) c) 8) (Cold bend for insulation)	-
Table 1 iii) d) 7) (Thermal stability- Sheath )	-
Table 1 iii) c) 7) (Thermal stability- Insulation )	-
Table 1 iii) d) 6) (Hot deformation -Indentation depth - Sheath )	-
Table 1 iii) d) 5) (Heat shock-Sheath )	-
Table 1 iii) c) 5) (Heat shock-Insulation )	-
Table 1 iii) d) 4) (Shrinkage- Sheath )	-
Table 1 iii) c) 4) (Shrinkage-Insulation)	-
Table 1 iii) d) 2) (Loss of mass- Sheath )	-
Table 1 iii) c) 2) (Loss of mass- Insulation )	-
Table 1 iii) d) 3) (Sheath- Elongation variation)	-
Table 1 iii) d) 3) (Sheath- TS variation)	-
Table 1 iii) d) 3) (Sheath- Elongation (After ageing))	-
Table 1 iii) d) 3) (Sheath- Tensile strength (After ageing))	-
Table 1 iii) d) 1) (Sheath- Elongation (Without ageing))	-
Table 1 iii) c) 3) (Elongation variation)	-
Table 1 iii) c) 3) (TS variation)	-
Table 1 iii) c) 3) (Elongation (After ageing))	-
Table 1 iii) c) 3) (Tensile strength (After ageing))	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-
Table 1 iii) c) 1) (Tensile strength (Without ageing))	-
4.2 (Conductor resistance test)	-
4.1 (Wrapping test (for Al))	-
4.1 (Tensile test (for Al)- After Stranding)	-
4.1 (Tensile test (for Al)-Before Stranding)	-
4.1 (Annealing test (for copper))	-
(Cl.16.1) (Cl.19.1) (Conductor- Diameter )	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
11.2 (Legibility)	-
11.1 (Durability)	-
11 (Identification)	-
10.9 (Additional ageing test (OU cables only) -HV test (at 60±3oC))	-
10.4 (Flammability test- Unaffected portion)	-
10.4 (Flammability test-Burning after flame removal)	-
Table 1 iii) d) 4) (Cracks Observed)	-
Table 1 iii) c) 4) (Cracks Observed)	-
(Cl. 18.1.4) (Cl. 19.1.5) (Cl. 20.1.4) (Cl. 22.1.4) (Colour of Sheath)	-
5.2 (Application )	-
9.1 (Ovality)	-
(Cl.6.1.3 of IS 8130:2013) (Flexible Conductors (Classes 5))	-
(Cl.6.1.3 of IS 8130:2013) ( Flexible Conductors (Classes 5))	-
(Cl.6.1.3 of IS 8130:2013) (Stranded circular non compacted conductors(Class-2))	-
(Cl.6.1.3 of IS 8130:2013) (Stranded compacted circular conductors and shaped conductors (Class 2))	-
(Cl.6.1.3 of IS 8130:2013) (Stranded circular non compacted conductors (Class-2))	-
(Cl.6.1.3 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.6.1 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.6.1 of IS 8130:2013) (Solid Conductor (Class 1))	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl.16.1) (Cl.19.1) (Conductor)	-
(Cl. 18.1.3) (Cl. 19.1.4) (Cl. 20.1.3) (Cl. 21.1.3) (Cl. 22.1.3) (Assembly of cores )	-
12 (CONSTRUCTION Core Identification)	-
8.1 (Sheath Material )	-
7 (Binder Tape)	-
6.1 (Filler)	-
6.2 (Filler)	-
5.1 (Insulation)	-
4.4 (Joints in Conductor)	-
4.4 (Joints in Conductor)	-
4.1 (Conductor - Material)	-
4.1 (Conductor - Material)	-
11 (Identification)	-
8.3 (Thickness of Sheath)	-
4.1 (Annealing test (for copper))	-
9 (Overall dimensions)	-
Table 1 iii) c) 6) (Hot deformation - Indentation depth- Insulation)	-
Table 1 iii) d) 1) (Sheath -Tensile strength (Without ageing))	-
8.3 (Minimum thickness of Sheath)	-
8.3 (Avarage thickness of Sheath)	-
5.3 (Minimum thickness of insulation)	-
5.3 (Avarage thickness of insulation)	-
Table 1 iii) c) 1) (Elongation (Without ageing))	-

Partial

Test facility not available for Copper purity test and FR/FRLSH category cables

275

IS 1554 : Part 1 (1988)

Specification for pvc insulated (Heavy Duty) electric cables: Part 1 for working voltages up to and including 1100 v (Third Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.2 (INSULATION : Thickness of Insulation)	-
12.3 (INNER SHEATH :Thickness of Inner Sheath)	-
13.3 (Armouring : Dimensions -Wire Diameter)	-
13.3 (Armouring : Dimensions -Formed wire )	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 a) (ARMOURING: Tensile Strength)	-
13.6 c) (ARMOURING: Torsion Test (For round wire ) )	-
13.6 d) (ARMOURING: Winding Test(For formed wire))	-
13.6 f) (ARMOURING: Mass of zinc coating )	-
13.6 g) (ARMOURING: Resistivity)	-
14.4.1 (Thickness of Outer Sheath : Unarmowed Cables)	-
15.1 a) 1) (Tests on conductor : Annealing test ( for copper ))	-
15.1 a) 4) (Tests on conductor : Conductor resistance test)	-
15.1 a) 4) (Resistance test - Neutral conductor )	-
15.1 d)1) (Phyaical tests for insulation : Tensile Test)	-
15.1 d)1) (Phyaical tests for insulation : Elongation )	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air Oven : Tensile Variation )	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air oven : Elongation Variation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation )	-
15.1 d)2) (Physical tests for outer sheath- Ageing in air oven : Tensile stregth Variation )	-
15.1 d)2) (Physical tests for outer sheath -Ageing in air oven : Elongation Variation )	-
15.1 d)3) (Phyaical tests for insulation : Shrinkage )	-
15.1 d)3) (Phyaical tests for Sheath : Shrinkage )	-
15.1 d)4) (Hot deformation : Insulation )	-
15.1 d)4) (Hot deformation : Sheath )	-
15.1 d)5) ( Loss of mass in air oven- Insulation )	-
15.1 d)5) ( Loss of mass in air oven- sheath )	-
15.1 d)6) (Heat shock test- Insulation )	-
15.1 d)6) (Heat shock test- sheath )	-
15.1 d)7) (Thermal stability- insulation )	-
15.1 d)7) (Thermal stability- Sheath )	-
15.1.e (Insulation resistance Test- Insulation resistance constant At Room temperature)	-
15.1.e (Insulation resistance Test- Insulation resistance At Maximum rated temperature temperature)	-
15.4 a) (Cold bend test- Insulation ( Optional test))	-
15.4 a) (Cold bend test- Sheath ( Optional test))	-
15.4 b) (Cold impact test- Insulation ( Optional test))	-
15.4 b) (Cold impact test- Sheath ( Optional test))	-
15.4 c) (Armour resistance test ( for other than mining cables ).- Optional test )	-
16.2 (DETAILS OF TESTS : High Voltage Test at Room Temperature)	-
16.3.1 (High Voltage Test ( Water Immersion Test ) : a.c. Test)	-
16.3.2 (High Voltage Test ( Water Immersion Test ) : d.c. Test)	-
16.4 (Flammability Test)	-
3.1 (MATERIALS : CONDUCTOR)	-
4.1.1 (INSULATION : General Purjose Insulaiion)	-
4.1.2 (INSULATION : Heat Resisting Insulation)	-
5.1 (MATERIALS : FILLER AND INNER SHEATH)	-
5.2 (MATERIALS : FILLER AND INNER SHEATH)	-
6.1 (MATERIALS : ARMGURING)	-
7.1.1 (OUTER SHEATH : For Cables with General Purpose InsuIafion)	-
7.1.2 (OUTER SHEATH : For Cables with Heat Resisting InsuIalion)	-
8.1 (CONSTRUCTION : CONDUCTOR)	-
8.2 (CONSTRUCTION : CONDUCTOR)	-
9.1 (INSULATION )	-
9.3 (INSULATION :Tolerance on Thickness of Insulation)	-
9.4 (INSULATION : Application of Insulation)	-
10.1 (CORE IDENTIFICATION)	-
10.2 (CORE IDENTIFICATION)	-
10.3 (CORE IDENTIFICATION)	-
10.3.1 (Arrangement of Marking)	-
11.1 (LAYING UP OF CORES)	-
11.2 (LAYING UP OF CORES)	-
12.1 (INNER SHEATH)	-
12.2 (INNER SHEATH)	-
13.1.1 (ARMOURING : Application)	-
13.1.2 (Armouring: Coverage )	-
13.1.3 (ARMOURING : Direction of lay )	-
13.1.4 (ARMOURING : Application)	-
13.2 (ARMOURING : Type of Armour)	-
13.2.1 (ARMOURING : Type of Armour)	-
13.4 (ARMOURING : Joints)	-
13.5.2 (ARMOURING : Resistance)	-
13.6 b) (ARMOURING: Elongation )	-
13.6 e) (ARMOURING: Uniformity of zinc coating)	-
14.1 (OUTER SHEATH)	-
14.2 (OUTER SHEATH)	-
14.3 (OUTER SHEATH : Colour )	-
14.4.2 (Thickness of Outer Sheath : Armoured Cables)	-
15.1 a) 2) (Tensile test (for aluminium) - Before stranding )	-
15.1 a) 2) (Tensile test (for aluminium) - After stranding )	-
15.1 a) 3) (Tests on conductor : Wrapping test ( for aluminium ))	-
17.1 (IDENTIFICATION : Manufacturer’s Identification)	-
17.2 (IDENTIFICATION : Cable Identification)	-
17.2.1 (IDENTIFICATION : Cable Identification)	-
17.3 (IDENTIFICATION : Cable Code)	-
9.3 (Minimum Thickness of Reduce core insulation)	-
9.2 (Thickness of Reduce core insulation)	-
15.1 d)2) (Phyaical tests for insulation- Ageing in air Oven : Tensile Test)	-
15.1 d)2) (Phyaical tests for insulation - Ageing in air oven : Elongation )	-
15.1 d)1) (Physical tests for sheath : Tensile stregth )	-
15.1 d)1) (Physical tests for sheath : Elongation )	-

Partial

Test facility not available for tests as per Cl. 15.1.1 of C1 and C2 category

276

IS 13334 : Part 1 (2014)

Skimmed milk powder - Specification: Part 1 standard grade (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.6 (Listeria monocytogenes)	-
5.6 (Spore count, Anaerobic (Sulfite reducing Clostridia))	-
5.6 (Spore count, Aerobic (Bacillus cereus))	-
5.6 (Salmonella)	-
5.6 (Coagulase positive Staphylococcus aureus)	-
5.6 (Escherichia coli)	-
5.6 (Coliform count )	-
5.6 (Bacterial count)	-
5.6 (Scorched particles)	-
5.6 (Milk fat)	-
5.6 (Titratable acidity (lactic acid))	-
5.6 (Total ash (on dry basis))	-
5.6 (Milk protein in milk solids not fat)	-
5.6 (Moisture)	-
5.2 (Absence of extraneous matter, added colour and added flavour)	-
4 (Description)	-
Cl 5.4 (The flavour of the product or of the reconstituted milk shall be pleasant and clean (see IS 10030).)	-
5.6 (Insolubility index)	-

Partial

(1) As per Cl. 5.7 The pesticide residues, heavy metals, toxins (aflatoxins and other naturally occurring toxins) and contaminants, if any, in the product shall not exceed the limits as prescribed in the Food Safety and Standards (Contaminants, Toxins and Residues) Regulations, 2011.’

277

IS 2347 (2017)

Domestic pressure cooker - Specification (Sixth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Capacity )	-
6.1.1 (Pressure Regulating Device)	-
6.1.5 (Pressure Regulating Device)	-
8.1 (Air Pressure Test)	-
8.2 (Proof Pressure Test)	-
8.3 (Operating Test for Pressure Regulating Device)	-
8.4 (Test for Safety Pressure Relief Device)	-
8.5 (Bursting Pressure Test)	-
8.6.1 (Tests for Removal of Lid under Pressure For Outer Lid Cooker)	-
8.6.2 (Tests for Removal of Lid under Pressure For inner Lid Cooker)	-
6.1.2 (Pressure Regulating Device)	-
6.1.3 (Pressure Regulating Device)	-
6.1.4 (Pressure Regulating Device)	-
6.2 (Safety Relief Device)	-
6.2.1 (Safety Relief Device)	-
6.3.1 (Temperature Responsive Pressure Relief Device)	-
6.4.1 (Handles and Knobs)	-
7.1 (WORKMANSHIP AND FINISH)	-
7.2 (WORKMANSHIP AND FINISH)	-
7.3 (WORKMANSHIP AND FINISH)	-
7.4 (WORKMANSHIP AND FINISH)	-
8.14 (3 Ply Construction Cooker Body)	-
6 (CONSTRUCTION)	-
6.1 (Pressure Regulating Device)	-
6.2 NOTE (Construction-Safety Relief Device)	-
11 (Marking)	-

Partial

The following test facilities are not available: (1) Material as per Clause 5.1, 5.2, 5.5, 5.6, 5.7, 5.8, 5.9, 5.10, 5.11 (2) Test for Hard Anodized Surface. (3) Test for spring-loaded mechanism (4) Test for handle and knob. (5) Electrical Pressure cooker

278

IS 2124 (2000)

Sodium bicarbonate - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Grade)	-
4.1 (Description)	-
4.2 (Table 1 S.no.(i)) (Total Alkalinity (as NaHCO3))	-
4.2 (Table 1 S.no.(i)) (pH )	-
4.2 (Table 1 S.no.(ii)) (Chlorides (as Cl))	-
4.2 (Table 1 S.no.(iii)) (Insoluble matter)	-
4.2 (Table 1 S.no.(iv)) (Sulphates (as SO4))	-
4.2 (Table 1 S.no.(v)) (Iron (as Fe))	-
4.2 (Table 1 S.no.(vii)) (Arsenic (as As))	-
4.2 (Table 1 S.no.(viii)) (Ammonium compounds (as NH4))	-
4.2 (Table 1 S.no.(ix)) (Phosphates (as PO4))	-
4.2 (Table 1 S.no.(x)) (Calcium and magnesium (as Ca))	-
4.2 (Table 1 S.no.(xi)) (Copper (as Cu))	-
4.2 (Table 1 S.no.(xii)) (Nitrates (as NO3))	-
4.2 (Table 1 S.no.(xiii)) (Silicates (as SiOz))	-
4.2 (Table 1 S.no.(xiv)) (Potassium (as K))	-
4.2 (Table 1 S.no.(xv)) (Substances reducing iodine)	-

Complete

279

IS 14151 : Part 2 (2008)

Irrigation equipment - Sprinkler pipes - Specification: Part 2 quick coupled polyethylene pipes and fittings (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1.2.2 ( Hydraulic Proof Test)	-
6.1.2, 6.1.2.1 ( Hydraulic Proof Test)	-
6.1.1, 6.1.1.1 (Leakage Test)	-
6.1 (Quick Coupled Pipes and Fittings)	-
4.1 .3 (Workmanship and Appearance)	-
4.1.5 (Rubber Ring)	-
Cl. 4.1.1.2.1, IS 14151 (P-1)-1999, Cl. 4, IS 2530-1963, Cl. 16 (Carbon Black Dispersion)	-
Cl.4.1 (Quick Coupled Male and Female Couplers)	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) Si-Killed (Silicon Content)	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) (Phosphorous Content)	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) (Sulphur Content)	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) (Manganese Content)	-
C. 4.1.1.1.2, IS 513 (P-1)-2016, Cl. 7.3, Table-3 , Grade O (CR1) (Carbon Content)	-
4.1.4(a) (Holding Attachments for Coupler Parts)	-
Cl 4.1.5 (Rubber rings- C)Rubber ring shall be of black colour:)	-
Cl 4.1.5 (Rubber rings- B) Change in hardness)	-
Cl 4.1.5 (Rubber rings- A)Shore hardness (Shore-A))	-
7.2.1 (Visual and Workmanship Requirement)	-
3 (QUICK COUPLED PIPES)	-

Partial

The following test facilities are not available: (1) Weldability Test

280

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2.1 (6.1.1 Identification Stripes)	-
7.4 table -3 & 4 (6.1 Dimensions)	-
8.2 (Longitudinal Reversion Test)	-
8.4 ( Melt Flow Rate)	-
8.3 (Carbon black)	-
6.2 (Colour)	-
6, 6.1 (PIPE DESCRIPTION)	-
7 ()	-
Clause 8.3 (Carbon Black Dispersion)	-
8.5 (Oxidation Induction Time)	-

Partial

The following test facilities are not available: (1)Internal Pressure creep rupture test (2)Tensile Strength for Butt-fusion (Clause 8.8) (3) Elongation at break (Clause 8.9) (4) Slow Crack Growth rate test (Clause 8.10) (5) Density (Clause 8.7) (6) Depth of strip (Clause 6.2.1) (7) Oxidation Induction Time (Clause 8.5) (8) Overall Migration (Clause 8.6) (9) Carbon Black content ( Clause 8.3) (10) For Size above 250 mm

281

IS 14543 (2016)

Packaged drinking water (Other Than Packaged Natural Mineral Water) - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.3 Table-1vi (pH)	-
5.3 Table-1 v (Total dissolved solids)	-
5.3 Table-1 iv (Turbidity)	-
5.3 Table-1 iii (Taste)	-
5.3 Table-1 ii (Odour)	-
5.3 Table-1 i (Colour)	-
5.3 (Description)	-
5.2.9 (Vibrio parahaemolyticus)	-
5.2.9 (Vibrio cholera)	-
5.2.8 (Shigella)	-
5.2.8 (Salmonella)	-
5.2.7 (Yeast and Mould)	-
5.2.6 (Aerobic Microbial Count at 37°C)	-
5.2.6 (Aerobic Microbial Count at 20-22°C)	-
5.2.5 (Pseudomonas Aeruginosa)	-
5.2.4 (Sulphite Reducing Anaerobes)	-
5.2.3 (Staphylococcus Aureus)	-
5.2.3 (Faecal Streptococci)	-
5.2.2 (Coliform)	-
5.2.1 (Escherichia coli (or thermotolerant bacteria))	-
5.3 Table-2 xi (Chloride (as Cl))	-
5.3 Table-2 xiv (Alkaliniity (as HCO3))	-
5.3 Table-2 i (Barium (as Ba))	-
5.3 Table-2 ii (Copper (as Cu))	-
5.3 Table-2 iii (Iron (as Fe),)	-
5.3 Table-2 iv (Manganese (as Mn))	-
5.3 Table-2 viii (Zinc (as Zn))	-
5.3 Table-2 ix (Silver (as Ag))	-
5.3 Table-2 x (Aluminium (as Al))	-
5.3 Table-2 xii (Selenium (as Se),)	-
5.3 Table-2 xxiii (Antimony (as Sb))	-
5.3 Table-2 xxiv (Borates (as B))	-
5.3 Table-3 i (Mercury (as Hg))	-
5.3 Table-3 ii (Cadmium (as Cd))	-
5.3 Table-3 iii (Arsenic (as As))	-
5.3 Table-3 v (Lead (as Pb))	-
5.3 Table-3 vi (Chromium (as Cr))	-
5.3 Table-3 vii (Nickel (as Ni))	-
5.3 Table-2 vi (Nitrite (as NO2))	-
5.3 Table-2 v (Nitrate (as NO3))	-
5.3 Table-2 xiii (Sulphate (as SO4),)	-
5.3 Table-2 xviii (Residual free chlorine)	-
5.3 Table-2 xxv (Bromates (as BrO3),)	-
5.3 Table-2vii (Fluoride (as F))	-
5.3 Table-2 xvii (Sodium (as Na))	-
5.3 Table-2 xvi (Magnesium (as Mg))	-
5.3 Table-2 xv (Calcium (as Ca),)	-
Table 3, x) (Uranium)	-
5.4 ii) (Total pesticied residue)	-
5.4 i) (Dieldrin)	-
5.4 i) (Aldrin)	-
5.4 i) (Malathion)	-
5.4 i) (Methyl Paraoxon)	-
5.4 i) (Methyl Parathion)	-
5.4 i) (Atrazine)	-
5.4 i) (Alachlor)	-
5.4 i) (Isoproturon)	-
5.4 i) (Butachlor)	-
5.4 i) (2,4-D)	-
5.4 i) (phorate sulphone)	-
5.4 i) (Phorate sulphoxide)	-
5.4 i) (Phorate)	-
5.4 i) (Chlorpyrifos)	-
5.4 i) (Monocrotophos)	-
5.4 i) (Endosulfan Sulphate)	-
5.4 i) (beta-Endosulfan)	-
5.4 i) (alpha-Endosulfan)	-
5.4 i) (Delta-HCH)	-
5.4 i) (beta-HCH)	-
5.4 i) (alpha-HCH)	-
5.4 i) (Gamma-HCH (Lindane))	-
5.4 i) (p,p DDD)	-
5.4 i) (o,p DDD)	-
5.4 i) (p,p DDE)	-
5.4 i) (o,p DDE)	-
5.4 i) (p,p DDT)	-
5.4 i) (o,p DDT)	-
5.3 Table-3 ix (Polynuclear aromatic hydrocarbons)	-
5.3 Table-3 viii (Polychlorinated biphenyle (PCB))	-
5.3 Table-2 xxii (Sulphide (as H2S))	-
5.3 Table-2 xx (Mineral oil)	-
5.3 Table-2 xxi (Anionic surface active agents (as MBAS))	-
5.3 Table-2 xix (Phenolic compounds (as C6H5OH))	-
5.4 i) (Ethion)	-
5.4 i) (Malaoxon)	-

Partial

Excluding Cyanide, Radio Active Elements. For testing of Pesticide Residues please indicate accordingly

282

IS 1786 (2008)

High strength deformed steel bars and wires for concretere inforcement - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 6.1 (Nominal Size)	-
Cl 7.2 (Weight)	-
Cl. 8.1 Table 3 (Elongation, percentage)	-
Cl. 8.1 Table 3 (TS/YS ratio)	-
Cl. 8.1 Table 3 (Tensile Strength (TS))	-
Cl. 5 (Cl.5 Mean area of ribs/unit length (Ar), )	-
Cl. 5 (Cl. 5 - Mean projected area of transverse ribs (1/3 of Ar))	-
Cl. 9.3, Table 4 (Bend Test )	-
Cl.9.4 & Cl. 9.4.1 (Rebend test)	-
4.1 (Silicon %)	-
4.1 (Sulphur %)	-
4.1 (Phosphorus %)	-
4.1 (Manganese %)	-
4.1 (Carbon %)	-
Cl. 8.1 Table 3 (Yield Stress (YS))	-
4.1 (Sulphur and phosphorous)	-

Partial

Test facilities are not available for the following: (1) Total elongation at maximum force, (2) Pull out test (Type test) (3) Sizes above 25 mm, (4) Micro-alloy/low alloys, Nb, V, B and Ti, Cr, Cu, Ni, Mo, Nirogen and nitrogen binding elements, like Nb, V, Ti, Al

Bureau of Indian Standards

The National Standards Body of India

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List