BIS - LIMS (Laboratory Information Management System)

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List

Reset

259 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

211

IS 1785 : Part 2 (1983)

Specification for plain hard drawn steel wire for prestressed concrete: Part 2 as - Drawn wire (First Revision)

Rs 3000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 5.1.2 (Weight)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.2 (Tensile Test On UTM)	-
Cl 6.3 (Tensile Test On UTM)	-
Cl 5.1 (Diameter)	-
Cl 5.1.2 (Weight)	-
3.1.1 (PHOSPHORUS)	-
3.1.1 (SULPHUR)	-
3.1.1 (PHOSPHORUS)	-
3.1.1 (SULPHUR)	-

-
Test facilities are not available for the following: 1. Tensile Test

212

IS 1785 : Part 1 (1983)

Specification for plain hard - Drawn steel wire for prestressed concrete: Part 1 cold drawn stress - Relieved wire (Second Revision)

Rs. 27300.00 (Complete testing charges) Rs. 9300.00 (F View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 5.1 (Diameter)	-
Cl 6.1 (Tensile Test On UTM)	-
Cl 6.2 (Tensile Test On UTM)	-
Cl 6.4 (Tensile Test On UTM)	-
Clause 3.1.1 (Phosphorus)	-
Clause 3.1.1 (Sulphur)	-

-
Test facilities are not available for the following: 1. Tensile Test

213

IS 1784 (2020)

Screwed Closures for Drums — Specification ( Fourth Revision )

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Dimensions-Steel flange- d1)	-
6 (Dimensions-Steel flange- d2)	-
6 (Dimensions-Steel flange- d4)	-
6 (Dimensions-Steel flange- h1)	-
6 (Dimensions-Steel flange- t1)	-
6 (Dimensions-Flange Gasket- wd)	-
6 (Dimensions-Flange Gasket-wt)	-
6 (Dimensions-Steel Bung- d1)	-
6 (Dimensions-Steel Bung- p1)	-
6 (Dimensions-Steel Bung- p3)	-
6 (Dimensions-Bung Gasket- wt)	-
6 (Dimensions-Capseals- d1)	-
6 (Dimensions-Capseals- d2)	-
6 (Dimensions-Capseals- w1)	-
6 (Dimensions-Capseals- h2)	-
6 (Dimensions-Tag Ring- d1)	-
6 (Dimensions-Tag Ring- d2)	-
6 (Dimensions-Zinc Bung- d1)	-
6 (Dimensions-Zinc Bung- d3)	-
8.4 (Curling Test for Flanges)	-
6 (Dimensions-Zinc Bung- d1)	-
6 (Dimensions-Zinc Bung- d3)	-
8.4 (Curling Test for Flanges)	-
6 (Dimensions-Zinc Bung- d1)	-
6 (Dimensions-Zinc Bung- d3)	-
8.4 (Curling Test for Flanges)	-
6 (Dimensions-Zinc Bung- d1)	-
6 (Dimensions-Zinc Bung- d3)	-
8.4 (Curling Test for Flanges)	-

-
-

214

IS 1783 : Part 2 (2014)

Drums large, fixed ends - Specification: Part 2 grade B drums (Fourth Revision)

5550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Capacity)	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
6 (Material)	-
7.5 (Construction)	-
9.1 (Leakage at air pressure )	-
9.2 (Drop Test)	-
9.3 (Hydraulic Pressure Test)	-

-
-

215

IS 1783 : Part 1 (2014)

Drums large, fixed ends - Specification: Part 1 grade A drums (Fourth Revision)

Rs.4800/- and testing charges as per relevant referred View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Material)	-
4 (Capacity)	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 C Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 1))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
5 (Dimensions (Type 1 D Drums Figure 2))	-
6 (Material)	-
9.1 (Leakage at air pressure )	-
9.2 (Drop Test)	-
9.3 (Hydraulic Pressure Test)	-

-
-

216

IS 1759 (1986)

Specification for powrahs (Second Revision)

Rs.2100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2.1 (Dimensions of Powrah-A)	-
2.3 (Blade thickness)	-
5.2 (Hardness)	-
4 (Mass)	-
10.1 (Drop test)	-

-
-

217

IS 1011 (2002)

Biscuits - Specification (Fourth Revision)

3280 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.3 Table 2 i (Moisture)	-
6.3 Table 2 ii (Acid insoluble ash (on dry basis))	-
6.3 Table 2 iii (Acidity of extracted fat (as oleic acid))	-

-
-

218

IS 299 (2012)

Alumino - Ferric - Specification (Fifth Revision)

Please see remarks View breakup
testing charges are Rs.3250.00 (for Grade 1, 2 & 3) and Rs.8250.00 (for Grade 4 & 5).

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
1 (i) Table 1 ( Insouble matter, Grade 1, A-3)	-
1 (ii) Table 1 (Soluble iron compound (as Fe2+ and Fe3+), Grade 1, A-4)	-
1 (iii) Table 1 (Water soluble aluminium compounds (as Al2O3), Grade 1, A-5)	-
1 (iv) Table 1 (pH (of 5 percent aqueous solution), Grade 1, A-6)	-
1 (v) Table 1 (Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 1, A-7)	-

-
Test facility not available for the following: 1. Cd, Se, Hg

219

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 9, IS 12235 Part 7 (Resistance to Sulphuric Acid)	-
Cl.7.1 (Mean out side Diameter (For less than or equal to 40 mm- Average of 8 , For higher diameters up to 110 mm average of 6))	-
Cl.7.1 (Outside Diameter at any point (Take 8 reading reported minimum, maximum))	-
Cl.7.1 (Wall thickness "minimum,maximum" (Take 8 reading))	-
Cl.7.3.1 (Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-
Cl.7.3.2 (Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-
Cl.8.2 (When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-
Cl8.3 (This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-
Cl.8.4 (When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-
Cl.10.1 (When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-
Cl.10.2 (When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-
Cl.10.3 (The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-
Cl.11. (Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-
Cl.7.2 (Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-
Cl.10.2 (When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-
Cl. 12, IS 12235 Part 11 (Resistance to Di-Chloro-Methane)	-

-
The following test facilities are not available: (1) For Outside Diameter above 250 mm, (2) Resistance to di chloromethane (3) Effect on water (Clause 8.6) (4) IMPACT TEST

220

IS 3074 (2013)

Steel tubes for automotive purposes - Specification (Third Revision)

4200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (STRAIGHTNESS)	-
8.3,18, (Flattening Test)	-
8.4 (Crushing Test)	-
8.5 (Drift Test)	-
8.2,15,17,22, Table 3,5 &7 (Tensile Tests,IS 1608 Part 1)	-
7, 20,Table 1,2,4 &6 ( C)	-
7, Table 1,2,4 &6 (Mn)	-
7, Table 1,2,4 &6 (S)	-
7, Table 1,2,4 &6 (P)	-
7, Table 1,2,4 &6 (Si)	-

-
Test facilities are not available for the following: 1. Ni, Cr, Mo, Micro alloying elements 2. Drift Expanding Test 3.Internal Hydraulic/Air Pressure Test

221

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

Rs 6760/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2 ( Body Thickness of the thinnest part of the finished utensil, mm Not declared )	-
5.2 (Lid Thickness of the finished utensil, mm)	-
6.1 & Table 1 (Inside dia, Φ D mm Not declared )	-
6.1 & Table 1 (Outside dia Ф NA)	-
6.1 & Table 1 (Height NA)	-
6.1 & Table 1 (Capacity, l NA)	-
6.1 ( Minimum sheet thickness for nominal size )	-
7.1 (HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-
7.2 (Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-
8.1 (The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-
8.2 (The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-
8.4.2 (A coating of thickness 25 to 100 microns is generally required)	-
8.4.3 (Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-
10 (Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-
9 (The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-
8.4.1.2 ( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-
8.4.4 (The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-

-
Complete test facility

222

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

5725 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Outer Diameter, Thickness & Mass)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
Cl 11 (Tensile Test, Flattening Test & Cold Bend Test)	-
5 AND AS PER IS 10748 (CARBON)	-
Clause - 5.1, Table-3 (SILICON)	-
Clause - 5.1, Table-3 (MANGANESE)	-
Clause - 5.1, Table-3 (SULPHUR)	-
Clause - 5.1, Table-3 (PHOSPHURS)	-

-
Test facilities are not available for the following: 1. Micro-alloying elements like Nb. V or Ti, Nitrogen, Al,Cu 2. Cold Bend test

223

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 13 (Length, Width & Thickness)	-
Cl 13 (Length, Width & Thickness)	-
Cl 13 (Length, Width & Thickness)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

-
Test facilities are not available for the following: 1. Boron, Titanium, Niobium, Vanadium, Nitrogen, Al, Cu 2. Cupping test

224

IS 2141 (2000)

Hot dip galvanized stay strand - Specification (Fourth Revision)

Rs7935/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (S)	-
4 (P)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.56 to 0.63 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.80 to 0.90 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 1.25 to 1.40 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 2.00 to 2.24 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.2.80 to 3.15 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Hard Core For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Hard Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.2 to 0.32 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.32 to 0.40 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.40 to 0.50 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.50 to 0.56 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.63 to 0.71 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.71 to 0.80 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 0.90 to 1.00 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 1.00 to 1.25 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 1.40 to 1.60 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 1.60 to 1.80 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 fo1.80 to 2.00 mm dia)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 For 2.00 to 2.24 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 2.24 to 2.50 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 2.50 to 2.80 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 2.80 to 3.15 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for3.15 to 3.55 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 3.55 to 4.00 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 4.00 to 5.00 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 5.00 to 7.10 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Mass of Zinc coating- as per IS 6745 for 7.10 to 10.00 mm dia For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.20 to 0.32 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.32 to 0.40mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.40 to 0.50mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.50 to 0.56 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.56 to 0.63 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.63 to 0.71 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.71 to 0.80 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.80 to 0.90 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 0.90 to 1.00 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.00 to 1.25 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.25 to1.40 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.40 to1.60 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.60 to 1.80 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 1.80 to2.00 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia2.00 to2.24 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 2.24 to2.50 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 2.50 to2.80 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 2.80 to3.15 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 3.15 to 3.55 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 3.55 to 4.00 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia4.00 to5.00 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 5.00 to 7.10 mm For Soft Core)	-
9.2 referes to IS 4826, Table 1 (Uniformity of zinc coating- As per IS 2633 for Dia 7.10 to10.00 mm For Soft Core)	-
11 (a) Size)	-
11 (b) Construction)	-
11 (c) tensile designation)	-
11 (d) lay)	-
11 (e) coating)	-
11 (f) length)	-
11 ( g) mass)	-
11 (h) manufacturer's name or trade mark)	-
11 (i) lot number along with the order number)	-
11 (j) BIS Standards Mark)	-
5 (a) Grade)	-
5 (b) Tensile Grade)	-
6 (a) Lay)	-
6 (b) Construction)	-
7 (Freedom from defects)	-
9 (a) Tensile)	-
9 (b) Elongation)	-
9 (c) Galvanizing Test)	-

-
Elongation test

225

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

Rs 3900/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 3.1.1 (Sulphur)	-
Clause 3.1.1 (Phosphorus)	-
Cl 5 & 6 (Diameter)	-
Cl 7 (UTM)	-
Cl 8.3 (Bending To Both Side At 90°, Then Straight)	-

-
Test facilities are not available for the following: 1. Nitrogen

226

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

Rs 2100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.2 (Diameter & Ovality)	-
Cl 6.2 (Weight)	-
Cl 8.2 (Bend test)	-
Cl 9.3 (Press)	-
Clause -4, 4.1 ( CARBON)	-
Clause -4, 4.1 (SULPHUR)	-
Clause -4, 4.1 (PHOSPHURS)	-
Clause -4, 4.1 (MANGANESE)	-
Clause -4, 4.1 (SILICON)	-

-
Test facilities are not available for the following: 1. Micro-alloying elements, Cu, Al, Nitrogen

227

IS 362 (1991)

Parliament Hinges -specification

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-A)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-B)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-C)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-D)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-E)	-
5.1-able 3 (Dimensions for Cast Brass Parliament Hinges-A)	-
5.1-able 3 (Dimensions for Cast Brass Parliament Hinges-B)	-
5.1-able 3 (Dimensions for Cast Brass Parliament Hinges-C)	-
5.1-able 3 (Dimensions for Cast Brass Parliament Hinges-D)	-
5.1-able 3 (Dimensions for Cast Brass Parliament Hinges-E)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-Thickness of Flap)	-
5.1-able 3 (Dimensions for Cast Brass Parliament Hinges-Thickness of Flap)	-
5.1-Table 4 (Dimensions for Mild Steel Parliament Hinges-A)	-
5.1-Table 4 (Dimensions for Mild Steel Parliament Hinges-B)	-
5.1-Table 4 (Dimensions for Mild Steel Parliament Hinges-C)	-
5.1-Table 4 (Dimensions for Mild Steel Parliament Hinges-D)	-
5.1-able 2 (Dlmenslons for Aluminium Alloy Parliament Hinges-d)	-
5.1-Table 4 (Dimensions for Mild Steel Parliament Hinges-d)	-
5.1-Table 4 (Dimensions for Mild Steel Parliament Hinges-Thickness of Flap)	-
6.3 (MANUFACTURE-Pins)	-

-
Test facilities are not available for the following: (1) Finish

228

IS 281 (2009)

Mild steel sliding door bolts for use with padlocks - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6-Table 1 (DIMENSIONS AND TOLERANCES-A)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-B)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-C)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-D)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-E)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-F)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-G)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-H)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-J)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-T)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for plate and sockets)	-
6-Table 1 (DIMENSIONS AND TOLERANCES-no. of 8m Sqire Holes for carriage bolts for Staple)	-

-
Test facilities are not available for the following: (1) Finish

229

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

Rs.3750.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 & Table 1 (Diameter & Difference Between Two Reading On Any Two Diameters)	-
Cl 9 (Tensile Test On UTM)	-
6 AND AS PER IS 7887 (PHOSPHORUS)	-
6 AND AS PER IS 7887 (SULPHUR)	-
6 AND AS PER IS 7887 (MANGANESE)	-
6 AND AS PER IS 7887 (SILICON)	-
6 AND AS PER IS 7887 (CARBON)	-

-
Test facilities are not available for the following: 1. Al, Cu

230

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
12.1 (Tensile Strength)	-
12.1 (Breaking load)	-
12.3 (Ductility)	-
12.2.1 (Mass of zinc coating (line wire))	-
12.2.2 (Mass of zinc coating (point wire))	-
12.2 (Uniformity of zinc coating)	-
9.1 (Freedom from defects)	-
9.2 (Freedom from defects)	-
7.2 (Manufacture)	-
5 Table-1 (Sizes No. of Lays between the two consequtive barbs)	-
5 Table-1 (Sizes Distance between two barbs)	-
5 Table-1 (Sizes Mass of Completed barbed wire)	-
5 Table-1 (Sizes Diamater of Point wire)	-
5 Table-1 (Sizes Diameter of Line wire)	-
4 (Type A/Type B)	-

-
1. Al, Cu,

231

IS 210 (2009)

Grey iron castings - Specification (First Revision)

2700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 (SIZE OF TEST BARS-Diameter)	-
13 (SIZE OF TEST BARS-Length)	-
15, Table 3 (TENSIL.E TEST- IS 1608 Part1 )	-
16, Table 3 (Hardness Test)	-
18 (HYDROSTATIC TEST)	-

-
Test facilities are not available for the following: (1)Hydrostatic Test (2) Brinell Hardness test

232

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

Rs.1500.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.3.1- Table 2,3,4,5 & Fig-1 & 2 (Screw Holes)	-
5.1- Table 2,3,4,5 & Fig-1 & 2 (Dimensions- 1. Holes for Screw Desination 2. No. of screw Holes)	-
5.2 ,Table 6 (Tolerances-Tolerances on dimensions of hinges )	-

-
Test facilities are not available for the following: (1) Anodizing thickness

233

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

Rs.2100.00. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1- Table 1 (Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-
6.2- Table 2 (Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-
6.2- Table 3 (PACKING)	-

-
Test facilities are not available for the following: (1) Finish

234

IS 277 (2018)

Galvanized steel strips and sheets (Plain And Corrugated) - Specification (Seventh Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8.1 (UTM)	-
Cl 8.2 (Press)	-
Cl 13 (Weight)	-
Cl 14 (Length, Width & Thickness)	-
Cl 10 (Galvanising Test)	-
7.1 & 10.2 (Mass of Coating: Single Spot Test)	-
7.1 & 10.2 (Mass of Coating: Triple Spot Test)	-
5.1 (phosphorus)	-
5.1 (silicon )	-
5.1 (manganese)	-
5.1 (sulphur)	-
5.1 (carbon)	-

-
Test facilities are not available for the following: 1. Ti, Al, Cu, micro-alloying element, Boron

235

IS 14255 (1995)

Aertal bunched cables - For working voltages up to and including 1100 Volts - Specification

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Phase/Street Lighting conductor)	-
4.2 (Messenger (Neutral Conductor or Otherwise))	-
5.1 (Insulation)	-
6.1 (Flexibility class)	-
6.2 (Compactness)	-
6.2 (No of strands)	-
6.2 (Surface)	-
6.3 (Protective barrier)	-
6.4 (size of street lighting conductor)	-
6.5 (Size of messenger conductor )	-
6.6 (Joints in messenger conductor )	-
6.6 (Direction of outer layer)	-
7.1 (Insulation)	-
7.2 ( Thickness of insulation)	-
7.3 (Tolerance on thickness of insulation )	-
7.4 (Aplication of the insulation )	-
7.5 (Colour of the insulation )	-
8.1 (Core identification)	-
8.2 (Core identification)	-
8.3 (Identification by other means)	-
9.1 (Assembly (Laying up))	-
9.2 (Assembly (Laying up))	-
9.3 (Direction of lay)	-
10.1 a) i) (Tests on phase/street light conductor: tensile test - Test method IS10810:Part 2)	-
10.1 a) ii) (Wrapping test - 10810: Part 3)	-
10.1 a) iii) (Resistance test - IS10810: Part 5)	-
10.1 b) i) (Test on messenger conductor: Breaking load - IS 10810: Part 2)	-
10.1 b) ii) (Test on messenger conductor: Elongation test - Cl 11.3)	-
10.1 b) iii) (Test on messenger conductor: Resistance test - IS 10810: Part 5)	-
10.1 c) i) (Physical tests for XLPE Insulation: Tensile strength - IS 10810: Part 7)	-
10.1 c) i) (Physical tests for XLPE Insulation: elongation at break - IS 10810: part 7)	-
10.1 c) ii) (Ageing in air oven : Tensile strength variation - IS 10810:Part 11)	-
10.1 c) ii) (Ageing in air oven : Elongation variation- IS 10810: Part 11)	-
10.1 c) iii) (Hot set test: Elongation under load - IS 10810: Part 30)	-
10.1 c) iii) (Hot set test: Permanent elongation (set) after cooling - IS 10810: Part 30)	-
10.1 c) iv) (Shrinkage test : Shrinkage - 10810:Part 12)	-
10.1 c) iv) (Shrinkage test : Crack Observed - 10810:Part 12)	-
10.1 c) v) (Water ahsorption (Gravimetric) - IS 10810: Part 33 )	-
10.1 d) i) (Physical test for PE insulation: Tensile strength - IS 10810: Part 7 )	-
10.1 d) i) (Physical test for PE insulation: elongation at break - IS 10810: Part 7)	-
10.1 f) (Insulation resistance (Volume resistivity) test a) volume resistivity at 27°C - IS 10810: Part 43)	-
10.1 f) (Insulation resistance (Volume resistivity) test b) volume resistivity at 70°C - IS 10810: Part 43)	-
10.1 g) (High voltage test - IS10810:Part 45)	-

-
Complete test facility is available

236

IS 9968 : Part 1 (1988)

Specification for elastomer insulatedcables: Part 1 for working voltages up to and including 1100 volts (First Revision)

Rs.12000/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 ( Copper Cooduetor)	-
3.2 (Aluminium conductor)	-
4.1 (INSULATION : lnsulation for General Service)	-
4.2 (INSULATION : Heat Resisting insulation)	-
4.3 (INSULATION : Silicone Rubber Insulation)	-
5.1 (TAPE : Proofed Tape)	-
5.2 (TAPE : 2 Polyethyl_ Terephthalate ( PETP ) Tape or Plastic: Tape or Any Other SlIIitable Tape )	-
5.3 (TAPE : Giass Tape)	-
6.1 (FILLERS : )	-
7.1 (BRAID : Textile Braid)	-
7.2 (BRAID : Glass Braid )	-
8.1 (SHEATH : General Service Insulated Cables and Flexible Cords)	-
8.2 (SHEATH :Heat Resisting Insulated Cables)	-
9.1 (PresenRtive Compound)	-
9.2 (Varnish)	-
10 ( Conductor )	-
11 (Separator tape)	-
12.2 (Insulation : Thickness of Insufatien)	-
12.4 (Insulation : Allplication of Insulation)	-
13 (CORE IDENTiFICATlON)	-
14 (Tape)	-
15 (BRAIDING)	-
16 (COMPOUNDING AND VARNISHING)	-
17 (LAYING UP OF CORES)	-
18 ( Binder tape)	-
19.2 (Sheath : Thickness of Sheath)	-
19.4 ( Sheath :Colour)	-
20 ( Overall diameter)	-
21. (b) (Annealing Test (for coper))	-
21. (c) ( Tensile Test (for aluminium))	-
21. (d) ( Wrapping Test (for aluminium))	-
21. (e) (Conductor Resistance )	-
21.1 ( Tensile strength )	-
22.1 ( Elongation)	-
21.1 (type test : Ageing In air oven)	-
21.1 (type test : Hot set elongation)	-
21.1 (type test : Tear resistance )	-
22.2 (type test :Insulauon resistance High voltage (water immersron ) test)	-
22.2 (type test : Flammability test ( applicable to cables finished With SE 3 and SE 4 sheaths only) )	-
23 (identification)	-

-
The following test facilities for clauses are not available: 1. Tear resistance test. 2. Water absorption (Electrical) Test for IE2 type elastomeric insulation

237

IS 9857 (1990)

Welding cables - Specification (First Revision)

Rs 11400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Conductor : Material )	-
5 (SEPARATOR)	-
6 (COVERING)	-
7 (CONDUCTOR : CONSTRUCTION )	-
8 (S E P A R A T O R)	-
9.1 (C O V E R I N G : Application )	-
9.2 (T h i c k n e s s o f C o v e r i n g)	-
9.3 (T o l e r a n c e on Thickness o f C o v e r i n g)	-
9.4 (A p p l i c a t i o n of C o v e r i n g)	-
9.5 (Colour of C o v e r i n g)	-
10.1 a) 1) (Annealing test - IS 10810: Part 1)	-
10.1 a) 2) (Conductor resistance tes - IS 10810 : Part 5)	-
10.1 c) 1) (Physical tests for covering : Tensile strength )	-
10.1 c) 1) (Physical tests for covering : Elongation at break )	-
10.1 c) 2) (Physical tests for covering - Ageing in Air oven : Tensile strength variation)	-
10.1 c) 2) (Physical tests for covering -Ageing in Air oven : Elongation at break )	-
10.1 c) 2) (Physical tests for covering - Ageing in Air oven : Tensile strength )	-
10.1 c) 2) (Physical tests for covering -Ageing in Air oven : Elongation variation at break )	-
10.1 c) 5) (Hot set test )	-
10.1 c) 5) (Permanent set )	-
11.1 (High Voltage Test ( Water Immersion Test ))	-
11.2 (Spark Test)	-
11.3 (Static Flexibility Test)	-
11.4 (Flammability Test)	-
12.1 (Manufacturer's Identification)	-
12.2 (Cable Identification)	-
12.3 (Cable Code)	-
13.1 (Packing )	-
13.2 (Marking)	-
14 (CABLE RATINGS)	-
15 (VOLTAGE DROP)	-

-
Complete test facility is available

238

IS 9537 : Part 3 (1983)

Specification for conduits for electrical installations: Part 3 rigid plain conduits of insulating meterials

1275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Marking)	-
6.2 (Durability of Marking as per 6.4 of IS: 9537 (Part 1)-1980)	-
6.3 (Standard Mark on Conduit)	-
7.1.1 (Maximum and minimum outside diameter of socket)	-
7.1.1 Table-2 (Length of Socket end)	-
7.1.2 (Maximum and minimum outside diameter of conduit)	-
7.2 (Minimum inside diameter of conduit)	-
7.3 (Length of conduit)	-
7.4 (Unifomity of The wall Thickness)	-
8.1 (Construction as per clause 8 of IS: 9537 (Part 1)-1980)	-
9.2 (Bending Test i) At Room Temp ii) At Low Temp (-5 ±2°C))	-
9.3 (Compression Test as per caluse 9.3 of IS: 9537 (Part 1)-1980)	-
9.4 (Impact Test as per clause 9.4 of IS: 9537 (Part 1)-1980)	-
9.5 (Collapse Test as per clause 9.5 of IS: 9537 (Part 1)-1980)	-
10 (Resistance to Heat -Ball presure test)	-
11 (Resistance to burning as per clause 11 of IS: 9537 (Part 1)-1980)	-
12 (Electrical Characteristics-Test for electric strength as per clause 12.1.1 of IS: 9537 (Part 1)-1980)	-
12 (Electrical Characteristics-Insulation resistance test as per clause 12.1.2 of IS: 9537 (Part 1)-1980)	-
9.3 (Compression Test (after removal of force) as per caluse 9.3.3 of IS: 9537 (Part 1)-1980)	-

-
Complete test facility is available

239

IS 8783 : Part 4 : Sec 3 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for individual wires: Sec 3 polyester and polypropylene insulated winding wires (First Revision)

Rs.8700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-
6.1 (The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-
6.1 (a) Reference to this Indian Standard;)	-
6.1 (b) Manufacturer's name,brand name or trade-mark;)	-
6.1 (c) Size of conductor / maximum overall diameter,)	-
6.1 (d) Length of conductor on spool / reel /coil;)	-
6.1 (e) Number of lengths onspool / reel / coil (if more than one);)	-
6.1 (f) Country of Manufacturer)	-
6.1 (g) Year of Manufacture.)	-
6.2 (BIS Certification Mark)	-
4 (i) Material)	-
5 (ii) Diameter [mm] Seperate wire:)	-
5 (ii) Diameter [mm] Wire taken from cable:)	-
5 (iii) Annealing test [Percentage] on Seperate wire:)	-
5 (iii) Annealing test [Percentage] on Wire taken from cable:)	-
5 (d) Resistance test [Ohm/km corrected to 20°c)	-
4.1, table 1 & 2 (a) Thickness of Polyster (mm))	-
4.1, table 1 & 3 (b) Thickness of Polypropylene (mm))	-
4.1, table 1 & 4 (c) Total thickness of Insulation(mm))	-
4.2 (Application of insulation)	-
4.3 (Colour of Insuation)	-
4.4 (Overall diameter (mm))	-
4 (Before ageing Tensile strength [N/mm²])	-
4 (Before ageing Elongation at break [Percentage])	-
4 (After ageing Tensile strength [N/mm²])	-
4 (Variation on tensile strangth [Percentage])	-
4 (After ageing Elongation at break [Percentage])	-
4 (Variation on elongation at break [Percentage])	-
4 (Shrinkage test [Percentage])	-
4 (After Shrinkage Cracks found.)	-
4.1 (Water absorption test [Gravimetric] [mg/cm²])	-
4.5 (High Voltage test [Water Immersion test] 3 KV for 1 Minute)	-
5 (The winding wire shall either be wound on spools / reels conforming to IS 482-1981. or supplied in a coils packed and labelled.)	-
6 (The winding wire shall carry following information marked on the lable on spool / reel / coil;)	-
6 (a) Reference to this Indian Standard;)	-
6 (b) Manufacturer's name,brand name or trade-mark;)	-
6 (c) Size of conductor / maximum overall diameter,)	-
6 (d) Length of conductor on spool / reel /coil;)	-
6 (e) Number of lengths onspool / reel / coil (if more than one);)	-
6 (f) Country of Manufacturer Marking)	-
6 (g) Year of Manufacture.)	-
6.2 (BIS Certification Mark)	-

-
The following test facilities for clauses are not available: Cl 4.1 Thickness of Insulation (Separate measurement of Thickness of Polypropylene and Polyester)

240

IS 8783 : Part 4 : Sec 1 (1995)

Winding wires for submersible motors - Specification: Part 4 specification for indmdual wires: Sec 1 HR PVC insulated wires (First Revision)

9300/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.3.1 (Conductor)	-
Cl.4 (Material)	-
Cl.5.1.1 (Dimensions)	-
Cl. 6 (Annealing Test)	-
Cl 6 (Resistance Test)	-
Cl 4.1.2 (Visual examination)	-
Cl.3.2 (Dielectric Material )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Volume resistivity)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile strength )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Tensile Strength)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Elongation at Break )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Variation)	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Shrinkage test )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Water absorption (Gravimetric) )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Hot deformation Test )	-
Cl. 4 Table 1of IS: 8783 (part 2) (Heat shock Test )	-
Cl.4.1 (Insulation )	-
Cl.4.2 (Application)	-
Cl.4.3 (Colour)	-
Cl.4.4 (Overall Diameter)	-
Cl.4.5 (Finish)	-
Cl.4.6 (High Voltage Test Water Immersion )	-

-
-

Bureau of Indian Standards

The National Standards Body of India

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List