BIS - LIMS (Laboratory Information Management System)

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List

Reset

259 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

181

IS 8737 (2017)

Valve fittings for use with liquefied petroleum gas (LPG) cylinders for more than 5 litre water capacity - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1Sl.No.i (Copper)	-
4.4 (Izod impact strength-IS 1598)	-
9.2a (Cycle Test)	-
9.5bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
4.3.1a (Tensile Strength-IS 1608)	-
4.3.1b (Elongation-IS 1608)	-
7.10 (The minimum finished wall thickness at any portion of the valve shall not be less than 2.5 mm)	-
9.3 (Operation Test)	-
9.5bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
9.5biii (Pneumatic Test ,after cycle test: Tightness of Joint Packing and Housing)	-
8.3.1 (Pneumatic Test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
8.3.2 (Pneumatic Test: Tightness of Valve Spindle and Valve Housing)	-
8.3.3 (Pneumatic Test: Tightness of Joint Packing and Housing)	-

-
"1.Cycles test 2. Security Cap /Nut 3. Spring a) Load Test b)Permanent set test c)Rust proofness of spring"

182

IS 8423 (1994)

Specification for controlled percolating hose for fire fighting

Rs. 4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.1.1 (The nominal internal diameter of hose shall be 38, SO, 63 and 70 rom.The internal diameter of the hose shall be measured by a suitable tapered plug gauge, and shall conform to the specified diameter within a tolerance of + 2·0 mm. -0'0)	-
Cl.5. (The hose length shall be 30 m or of such length as required.)	-
Cl.6 (The hose shall be flexible and on being machine coiled, the diameter of the coil of 30 m hose shall not exceed 45 em for all slzes in dry state without coupling. The coil diameter shall be measured at the widest part of the coil.)	-
Cl.7 (The average mass oC hose per metre shall not be more than that prescribed in Table 1. For determination of mass, sample of the hose shall be conditioned at 27 ± 2°C and 65 ± 5 percent relative humidity Cor a period of at least 48 hours and then shall be weighed under same conditions.)	-
Cl.8 (The percolation, when tested in accordance with the procedure laid down in 8.1.1 shall not exceed the limits prescribed in Table 2.)	-
Cl.9 (The full length sample of the dry hose is connected to the pump fitted with water and pressure built up to. 7 kaf/cn,' (70 N/cm' ) steadily over a period of two minutes. After the hose has been at pressure 7 kif/em' ( 70 NIemi) for a period of S minutes, a visual inspection I is made of the length to ascertain the evenness and degree of wetting out along the complete length of hose and at least 75 percent of the hose jacket shall be evenly and consistently wetted out in this manner.)	-
Cl.10 (Full length of hose shall be subjected to an internal hydraulic pressure of 2'1 MPa (21'4 kgf/ems ) at the rate of I MPa ( 10'2 kaf/em· )/ minute in ac.cordance with 1.3 of IS 443 : 191~ and maintained for a period of one minute. During this test. the hose shan not show breakage of yarn.)	-

-
-

183

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

Rs.7200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Nominal Diameter & Out Of Shape)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

-
Test facilities are not available for the following: 1. Chemical composition (Al)

184

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

Rs.2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 2.2.2 (Dimensions)	-

-
The following test facilities are not available: 6.3 Effect on water

185

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

Rs.2400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Minimum Thickness)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Minimum Socket Length)	-
Cl. 5.1.1, 5.1.2, Table 1, Fig 1 (Out-of-roundness tolerances of socket inside diameter)	-
Cl. 6.1 (Stress Relief Test- Appendix A)	-
Cl. 6.2 (Opacity- Appendix B)	-
Cl. 6.4 (Short-Term Hydraulic Test- Appendix D)	-
6.4 (Short-Term Hydraulic Test)	-

-
The following test facilities are not available: 6.3 Effect on water

186

IS 15490 (2017)

Seamless steel cylinders for on - Board storage of compressed natural gas as a fuel for automotive vehicles - Specification (First Revision)

16297 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2 (Cylinder shape and wall thickness)	-
7.6 (Out-of-Roundness)	-
7.7 (Mean Diameter)	-
7.8 (Straightness)	-
9.3.1 (Tensile Strength)	-
9.3.2 (Bend test)	-
9.3.3 (Impact test)	-
5.2.1,5.2.2,5.3 (Carbon)	-
5.2.1,5.2.2,5.3 (Manganese)	-
5.2.1,5.2.2,5.3 (Silicon)	-
5.2.1,5.2.2,5.3 (Sulphur)	-
5.2.1,5.2.2,5.3 (Phosphorus)	-

-
Test facilities are not available for the following: 1. Cr, Ni, Mo, V, Al, N, B, Zr 2.Pressure cycling Test 3. Base check 4. Hydrostatic Stretch Test 5. Leakage Test 6.Neck threads 7. Surface Defects 8. Verticality 9. Hydraulic Bursting Test 10. Sulphide Stress Cracking Resistance Test 11 Ultrasonic testing 12 Leakage before breakage test 13 Bonfire test Remark: Prepared piece for tensile (2 nos), bend (4 nos) and impact (3 nos)

187

IS 7285 : Part 1 (2018)

Refillable seamless steel gas cylinders - Specification: Part 1 normalized steel cylinders (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.5 (Mean Diameter)	-
10.1.3 a) & Clause 5.4 Table 3, i) ( Tensile strength (Rg) )	-
10.1.3 a) & Clause 5.4 Table 3, ii) ( Yield strength (Re))	-
Clauses 6.8 and 10.3.1,Table 4 iii), Sr.no.3 (Impact Test-Cylinder Diameter Dm >140 mm i) Direction- Transverse: ii) Test temperature, in °C –20)	-
Clauses 5.2.1 and 5.4, Table 1 (Controls on Chemical Composition)	-

-
Test facilities are not available for the following: 1. Cr, Ni, Mo, V, Al, N, B, Zr 2.Pressure cycling Test 3. Base check 4. Hydrostatic Stretch Test 5. Leakage Test 6.Neck threads 7. Surface Defects 8. Verticality 9. Hydraulic Bursting Test 10. Sulphide Stress Cracking Resistance Test 11 Ultrasonic testing Remark: Prepared piece for tensile (2 nos), bend (4 nos) and impact (3 nos)

188

IS 7142 (1995)

Welded low carbon steel cylinders for low pressure liquifiable gases not exceeding 5 litre water capacity - Specification (First Revision)

Rs. 9552/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
13 (CHECKING OF WATER CAPACITY)	-
15.1 (PNEUMATIC LEAKAGE TEST)	-
17.3 i) (Acceptance test Parent Metal Longitudinal test specimen;)	-
17.3 ii) (Acceptance test Parent Metal Longitudinal test specimen;)	-
17.3 iii) (Acceptance test Parent Metal Longitudinal test specimen;)	-
17.3 v) (Acceptance test Parent Metal Circumferential test specimen;)	-
17.3 vi) (Acceptance test Parent Metal Circumferential test specimen;)	-
17.3 vii) (Acceptance test Weld joint test Specimen)	-
17.4 (Bend test across weld)	-
17.6 (Minimum Thickness Test)	-
14.1.1 (PROOF TEST)	-

-
Test facilities are not available for the following: 1. Thread gauges

189

IS 7092 : Part 2 (1987)

Specification for aluminium alloy tube for irrigation purposes: Part 2 extruded tube (Second Revision)

Rs 11230/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.6.2 (Ultimate Tensile Strength- IS 2657)	-
Cl.6.2 (0.2 percent proof strength- IS 2657)	-
Cl.6.2 (Elongation on 50 mm gauge length- IS 2657)	-
Cl. 6.3 (Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-
Cl. 6.4 (Hydrostatic Pressure Test-Cl. 6.4)	-
Cl.7.1, Table 2 (Outside Diameter-)	-
Cl.7.1, Table 2 (Roundness or Ovality)	-
Cl.7.1, Table 2 (Wall Thickness)	-
Cl. 7.2 (Length)	-

-
" 1. Tensile Test 2. Hydrostatic Machine "

190

IS 6603 (2001)

Stainless steel bars and flats - Specification (First Revision)

3150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Carbon -Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Silicon- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Manganese- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Sulphur- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
Cl. 7.1, 7.2, 7.3 & 13.1 Table 1 (Phosphorus- Established instrumental/ chemical method as agreed to between purchaser and the manufacturer.)	-
9.1, Table 3 (0.2 Percent Proof Stress, MPa)	-
9.2, Table 3 (Tensile Strength, MPa)	-
9.3, Table 3 (Elongation ,Percent)	-
9.4, Table 3 (Annealed Hardness, HB-IS 1500: Pt 1)	-
12 (Dimensions & Tolerances, mm-IS 6603)	-
9.5, Table 3 (Charpy Impact Test, J-IS 1499)	-

-
Test facilities are not available for the following: 1. Ti, Nb, Mo, Cu 2. Corrosion resistance Remark: Prepared piece of impact (3 nos)

191

IS 6529 (1996)

Stainless steel blooms, billets and slabs for forging - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1,7.2,7.3 Table 1 (Carbon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Sulphur-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Phosphorous-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Manganese-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7.1,7.2,7.3 Table 1 (Silicon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

-
Test facilities are not available for the following: 1. Ni, Cr, Mo, Ti, Nb, N 2. Corrosion Test

192

IS 14333 (1996)

High Density Polyethylene Pipe For Sewerage -

3900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Dimensions of pipes)	-
8.1 (Hydraulic characteristics)	-
8.2 (Reversion)	-
8.4 (Melt Flow Rate)	-
Cl. 8.5, IS 2530-1963, Cl. 16 (Carbon Black Dispersion)	-
8.3 (Density)	-

-
The following test facilities are not available: (1)Internal Pressure creep rupture test (2)Tensile Strength for Butt-fusion (3) Slow Crack Growth rate test (4) Depth of strip (5) Overall Migration (7) Carbon Black content (8) For Size above 250 mm

193

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

9710 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 13 (Length, Width & Thickness)	-
Cl 7 (UTM)	-
Cl 8 (Press)	-
Cl 7 (UTM)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

-
Test facilities are not available for the following: 1. Al, N, Micro alloying element 2. Erichsen Cuppling Machine

194

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

-
Test facilities are not available for the following: 1. Micro alloy, N, Al, Cu, Cr, Mo, Ni

195

IS 4923 (2017)

Hollow steel sections for structural use - Specification (Third Revision)

7290 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.7.1 (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.7.1 (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Depth))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Width))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections(Thickness))	-
Cl.9.1, Table 1 (Dimensions and Properties of Hollow Sections (Weigth))	-
Cl. 10.1, 14.1, 18.1 (Straightness)	-
Cl. 10.4, Fig 2 (Concavity, X1)	-
Cl. 10.4, Fig 2 (Convexity, X2)	-
Cl. 10.5, Fig 3 (Squareness of side)	-
Cl. 10.6, Fig 4 (External Corner Radius)	-
Cl. 10.5, Fig 3 (Squareness of side)	-
Cl. 10.6, Fig 4 (External Corner Radius)	-
Cl. 10.7, Fig 5 (Total twist, V)	-
Cl. 15.2, Table 3 (Tensile Strength- IS 1608)	-
Cl. 15.2, Table 3 (Yield Strength- IS 1608)	-
Cl. 15.2, Table 3 (Elongation- IS 1608)	-
Cl. 14.1 (Exact Length)	-
Cl. 14.1 (Weight on individual length)	-
Cl. 14.1 (Exact Length)	-
Cl. 14.1 (Weight on individual length)	-

-
Test facilities are not available for the following: 1. Cu

196

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

Rs.7500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Tensile Test & Flattening Test)	-
Cl 7 (Outer Diameter, Thickness, Mass & Straightness)	-
Cl 9 (Pipe ends, Angle of bevel & Root Face )	-
Cl 10 (Outer Diameter & Overall Length)	-
Cl 10 (Outer Diameter & Overall Length)	-
Cl 9 (Pipe ends, Angle of bevel & Root Face )	-
Cl 10 (Outer Diameter & Overall Length)	-
Cl 10 (Outer Diameter & Overall Length)	-
5.2 (phosphorus)	-
5.2 (sulphur)	-

-
Except Hydrostatic test (Cl.8)

197

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 & Table 3 (UTM)	-
Cl 9 (Press)	-
Cl 12 & 13 (Length, Width & Thickness)	-
Cl 12 & 13 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
7.1 (Silicon %)	-

-
Test facilities are not available for the following: 1. V, Nb, Ti, Al, Nitrogen, Mn, Cr, Mo, V, Ni, Cu

198

IS 4148 (1989)

Surgical rubber gloves - Specification (First Revision)

Rs. 3925/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.5 (pH of Aqueous Extract )	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.2 (Dimensions Fig 1 and Table 1)	-
4.3 (Thickness)	-
4.4.2 (After accelerated aging at 70 + 1OC for 240 h )	-
4.4.3 (After heat ageing in autoclave)	-
4.4.4 (Tension Set)	-

-
-

199

IS 3589 (2001)

Steel pipes for water and sewage (168.3 To 2540 Mm Outside Diameter) - Specification (Third Revision)

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.3 (Guided bend test(For SAW Pipes))	-
11.1, Table 5. (Outside Diameter (OD))	-
11.1, Table 5. (Thickness)	-
11.1, Table 5. (Mass)	-
12.3.3 (Ovality)	-
12.5 (Strightness)	-
9.2.1 (Flattening test for ERW pipes )	-
9.1 (Tensile test-Yield Strength)	-
9.1 (Tensile test-Strength)	-
9.1 (Tensile test- Elongation)	-
8.1 Table 2 Table 3 (Carbon Content IS 228)	-
8.1 Table 2 Table 3 (Manganese Content IS 228)	-
8.1 Table 2 Table 3 (Phosphorus Content IS 228)	-
8.1 Table 2 Table 3 (Sulphur Content IS 228)	-

-
Test facilities are not available for the following: 1. Al, Micro Alloying element (Nb, V, Ti) 2. Hydrostatic Pressure test 3. Size above 914 mm nominal diameter

200

IS 3575 (1993)

Bitumen drums - Specification (Third Revision)

1800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 (Dimensions Closure (Figure 2))	-
5.1 (Body and ends)	-
5.2 (Closures)	-
8 (Air Pressure Test)	-
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Drums (Figure 1))	-
4.1 (Dimensions Closure (Figure 2))	-

-
-

201

IS 3390 (1988)

Specification for sphygmomanometers, mercurial (Second Revision)

Rs 7800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1.2 (Fastening)	-
4.1 (Metal Parts)	-
4.2 (Rubber Parts -Inflation Bulb)	-
4.2 (Rubber Parts:- Rubber Tubing BEFORE AGEING)	-
4.2 (Rubber Parts:- Rubber Tubing BEFORE AGEING)	-
4.2 (Rubber Parts:- Rubber Tubing AFTER AGEING)	-
4.2 (Rubber Parts:- Rubber Tubing AFTER AGEING)	-
4.8.2.1 (Cuff Dimension & fig 1)	-
4.8.2.1 (Cuff Dimension & fig 1)	-
4.8.2.1 (Cuff Dimension & fig 1)	-
4.8.3.1 & 4.8.3.2 (Inflating Bag)	-
4.8.3.1 & 4.8.3.2 (Inflating Bag)	-
4.8.4 (Tubing)	-
4.8.4 (Tubing)	-
4.9.1 (Pressure Measuring Device)	-
4.9.1 (Pressure Measuring Device)	-
4.9.3 (Reservoir and Connecting Tube)	-
4.9.4 (Extension Tube)	-

-
Separate prepared piece of raw material (16 nos) required for tensile and % elongation to be conducted before and after ageing.

202

IS 3319 (1995)

Blades, surgical, detachable (Bard Parker Type) and handles - Specification (Fourth Revision)

Please check remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5,5.1 & 5.2; Table 1 (Shape and dimensions)	-
9.1 ( Visual Examination)	-
7.1 (Hardness test)	-
Clause -4, 4.1 (SILICON)	-
Clause -4, 4.1 (MANGANESE)	-
Clause -4, 4.1 (PHOSPHURS)	-
Clause -4, 4.1 (SULPHUR)	-
Clause -4, 4.1 ( CARBON)	-

-
Test facilities are not available for the following: 1. Ni, Cr, Mo, N, Al 2. hardness Test 3.Perfomance Test 4. Visual Examination

203

IS 3196 : Part 2 (2006)

Welded low carbon steel cylinders exceeding 5 litre water capacity for low pressure liquefiable gases: Part 2 cylinders for liquefiable non - Toxic gases other than lpg - Specification (First Revision)

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4 (Material)	-
16 (Pneumatic Leakage Test)	-
14 (Water Capacity)	-
18 (a)Parent metal Longitudinal specimen)	-
18 (a)Parent metal Circumferential specimen)	-
18 (c)Weld Joint test specimen)	-
18.1.3 (Root Bend test,)	-
18.1.3 (Face Bend Test,)	-
18.1.5 (Minimum Thickness test)	-
22.2 (Outside surface)	-
10 (Foot Ring)	-

-
Test facilities are not available for the following: 1. Cycle Test 2. Impact and Drop Test 3. Radiographical Examination 4 HST test

204

IS 5986 (2017)

Hot rolled steel sheet, plate and strip for forming and flanging purposes - Specification (Fourth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Press)	-
Cl 10 (Sudden Load Applied)	-
Cl 15 (Length, Width & Thickness)	-
7.1 (Carbon %)	-
7.1 (Manganese %)	-
7.1 (Phosphorus %)	-
7.1 (Sulphur %)	-
7.1 (Silicon %)	-

-
Test facilities are not available for the following: 1. Micro alloy, Al, Cu, Ni, Cr, Mo 2. Hole Expansion Test Remark: Prepared piece of impact (3 nos)

205

IS 2871 (2012)

Branch pipe, universal for fire fighting purpose - Specification (Second Revision)

Rs.2200/- (excl. operational test) View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (Shape & Dimensions)	-
Cl 6.1 (Hydraulic Test)	-
Cl 6.2 (Operational Test)	-

-
-

206

IS 2415 (2015)

Cycle - Rubber tubes (Moulded/ Jointed) - Specification (Fourth Revision)

Rs 14270/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1,3.4, Annex A & Table 2. ( Flat Length )	-
5.1,3.5, Annex A & Table 2. (Flat Width)	-
5.2, Annex A (Thickness)	-
5.2.1 (Uniformity of Thickness)	-
6.1,Table 3 (i)Tensile strength:)	-
6.1,Table 3 (ii)Elongation at break )	-
6.3 (a) ( Ageing Test:- Tensile strength :)	-
6.3(b) ( Ageing Test :- Elongation at break)	-
6.4.1 (Joint Adhesion Strength)	-
6.4.3 ( Strength of splice on moulded tube)	-

-
Complete test facility,

207

IS 1971 (1996)

Crop protection equipment - Hand - Operated stirrup - Specifation (Fifth revision)

Rs 4800/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6.1 (Discharge rate)	-
Cl 6.2 (Volumetric Efficiency)	-
Cl 6.3 (Endurance)	-
Cl 7.1 (Height)	-
Cl 7.2 (Total Mass)	-
Cl 7.3 (Pump Cylinder)	-
Cl 7.4 (Piston)	-
Cl 7.5 (Piston rod)	-
Cl 7.6 (handle)	-
Cl 7.9 (Stirrup & Foot Resr)	-
Cl 7.13.1 (Delivery Hose)	-
Cl 7.13.3 (cut Off device & Lance)	-
Cl 7.13.4 (Nozzle)	-

-
-

208

IS 5872 (1990)

Cold rolled steel strips (Box Strappings) - Specification

6050 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (UTM)	-
Cl 7 (Bending To Both Side At 90°, Then Straight)	-
Cl 10 (Width & Thickness)	-
5 (Chemical Composition)	-
5.0 & 5.1 , Table 1 & 2 (Carbon)	-
5.0 & 5.1 , Table 1 & 2 (Sulphur)	-
5.0 & 5.1 , Table 1 & 2 (Manganese)	-
5.0 & 5.1 , Table 1 & 2 (Phosphorus)	-

-
1. Micro alloying elements

209

IS 1825 (1983)

Specification for aluminium alloy milk cans (Second Revision)

Rs 4800.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (h) Mass 6.5 Kg. Min.)	-
2 (Capacity)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Drain Holes )	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Dimension)	-
4 Fig. 1 (Hole Dia 8 ,2 holes)	-
4 Fig. 1 (Hole Dia 12, 3 holes)	-
5 (i) If the thickness at shoulder is less than 2.5 mm a )	-
5 (reinforcement ring of 2 mm thickness shall be provided.)	-
5 (ii) Brinell Hardness 85 HB Min.)	-
7 (i) Air Pressure Test (Cl 7.1))	-
7 (ii) Drop Test (Cl 7.2))	-
7 (iii) The cans when filled with water and inverted shall not show any profuse leakage through lids. )	-

-
-

210

IS 5504 (1997)

Specification for spiral welded pipes (First Revision)

testing charges for the product are Rs 8640/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 5.1 (Carbon)	-
Cl. 5.1 (Phosphorus)	-
Cl. 5.1 (Sulphur)	-
6.1 (Tensile Test)	-
6.2 (Flattening Test)	-
6.3/6.3.1.1 (Submerged Arc Weld Test- Guided bend test)	-
8.1 (Length)	-
8.2 (Dimensions)	-

-
Test facilities are not available for the following: 1. Hydrostatic Pressure test 2. Size above 914 mm nominal diameter

First
Prev
6
7
8
9
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List