BIS - LIMS (Laboratory Information Management System)

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List

Reset

255 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

151

IS 963 (1958)

Specification for chrome molybdenum steel bars and rods for aircraft purposes

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Suphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
6.1 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

-
Test facilities are not available for the following: 1. Hardenbility 2.Micro Examination (Sulphur Print Test) 3. Grain Size 4.Decarburization 5. Mo, Ni, Cr

152

IS 11587 (1986)

Specification for structural weather resistant steels

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 5.1, Table -1 (WR-Fe 480 A, C )	-
Clause 5.1, Table -1 (WR-Fe 480 A, Si)	-
Clause 5.1, Table -1 (WR-Fe 480 A, Mn)	-
Clause 5.1, Table -1 (WR-Fe 480 A, P )	-
Clause 5.1, Table -1 (WR-Fe 480 A, S )	-
Cl 8 (Tensile Test)	-
Cl 9 (Bend Test)	-
Cl 12 (Freedom from Defects)	-
Cl 10 (Impact Test)	-
Cl 11 (Flattening Test)	-
Cl 13 (Dimensions)	-
Cl 8 (Tensile Test)	-
Cl 9 (Bend Test)	-
Cl 12 (Freedom from Defects)	-
Cl 10 (Impact Test)	-
Cl 11 (Flattening Test)	-
Cl 13 (Dimensions)	-

-
-

153

IS 9825 (2003)

Chlorine tablets - Specification (Second Revision)

Rs.4330/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.2 (Description)	-
Cl.4.3 (Size (Mass of tablet))	-
Cl.4.3 (Available Chlorine (Annex A))	-
Cl.4.4 (Moisture (Annex B))	-
Cl.4.4 (Shelf Life (Annex A))	-

-
-

154

IS 9962 (1981)

Specification for steel wire for needles

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 (Silicon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 (Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 (Phosphorus- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

-
Test facilities are not available for the following: 1) Degree of spheroidization 2) Depth of decarburization

155

IS 10632 : Part 3 (1983)

Specification for non magnetic stainless steels for electrical applications: Part 3 specific requirements for sheets, strips and plates

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
3.1 (Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
3.1 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
3.1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

-
Test facilities are not available for the following: (1) Electric Resistivity (2)Mangentic property 3) Chemical composition (Ni, Cr, Co, Mo, Cu, Fe)

156

IS 10632 : Part 2 (1983)

Specification for non magnetic stainless steels for electrical applications: Part 2 specific requirements for binding wires

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
3.1 (Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
3.1 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
3.1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-

-
Test facilities are not available for the following: (1) Electric Resistivity (2)Mangentic property 3) Chemical composition (Ni, Cr, Co, Mo, Cu, Fe)

157

IS 15911 (2010)

Structural steel (Ordinary Quality) - Specification

Rs 6750/- For elements other than Table-1: Rs 1004/- pe View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table-1, 5.1, 8.1 & 8.2 (Carbon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Sulphur: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Phosphorous: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Manganese: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
Table-1, 5.1, 8.1 & 8.2 (Silicon: Relevant parts of IS 228 or any other established instrumental/chemical method)	-
5 and 10.3.1 (Tensile strength. IS 1608)	-
5 and 10.3.1 (Yield Stress. IS 1608)	-
5 and 10.3.1 (Percentage Elongation. . IS 1608)	-
5 and 10.3.1 (Internal Bend Diameter)	-
11.3 ( Bend Test. IS 1599)	-

-
Test facilities are not available for the following: 1. Microalloying elements, Mn, Al, Ni, Cu, Cr, Mo, N

158

IS 10631 (1983)

Specification for stainless steel for welding electrode core wire

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table 1 (Carbon- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Sulphur- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Phosphorous- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
5.1 Table 1 (Manganese- Relevant parts of IS 228 or any other established instrumental /Chemical method)	-
7 (Size and Tolerances)	-

-
Test facilities are not available for the following: 1. Cr, Ni, Mo

159

IS 1029 (1970)

Specification for hot-rolled steel strip (Baling) (First Revision)

Rs.750/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4 (Sulphur -IS 228 or method specified in relevant ISO standard)	-
Cl.4 (Phosphorus -IS 228 or method specified in relevant ISO standard)	-

-
-

160

IS 15961 (2012)

Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain)

Rs.4990 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 & Table 2 (Workmanship)	-
Cl 12 (Weight)	-
Cl 10 (Coating Adhesion )	-
Cl 13 (Length, Width, Thickness, Camber, Deviation From Squareness & Deviation From Flatness)	-
Cl 11 (Workmanship)	-
Cl. 13.7 (Deviation from Flatness (Steepness))	-
Cl. 13.6 (Deviation from Squareness (Out of Square))	-
Cl. 13.5 (Camber)	-
4, 5 (CARBON)	-
4, 5 (SULPHUR)	-
4, 5 (PHOSPHURS)	-
4.5 (MANGANESE)	-
Clause 9 (Coating Test (Triple Spot Test) (Total Both Surface))	-
Clause 9 (Coating Test (Single Spot Test) (Total Both Surface))	-
Clause 9 (Coating Test (Single Spot Test) (One Surface))	-

-
-

161

IS 15778 (2007)

Chlorinated polyvinyl chloride (Cpvc) pipes for potable hot and cold water distribution supplies - Specification

6375 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 IS 12235 (Part 1) Table 2 (Dimension of Pipes: Mean outside Diameter)	-
7.1,7.1.1 IS 12235 (Part 1) Table 2 (Outside Diameter at any point)	-
7.1.2 IS 12235 (Part 1) Table 2 (Wall Thickness )	-
9.2 IS 12235 (Part 3) (Opacity)	-
9.4 IS 12235(Part 5/Sec 1 and Sec 2) (Reversion Test : When tested by the method prescribed in IS 12235(Part 5/Sec 1 and Sec 2), a length of pipe 200 + 20 mm long shall not alter in length by more than 5 percent.)	-
9.5 IS 12235(Part 2) (Vicat Softening Temperature: When tested by the method prescribed in IS 12235(Part 2), the Vicat softening temperature of the specimen shall not be less than 110°C.)	-
9.6 IS 12235(Part 14) (Density)	-
10.3 IS 4985 Table 4 (Resistance to External Blow at O°C: When tested by the method prescribed in IS 4985, with classified striker mass and drop height as given in Table 4, the pipe shall have a true impact rate of not more than 10 percent.)	-
10.4 IS 12235(Part 19) (Flattening Test)	-
10.5 IS 12235(Part 13) (Tensile Strength : When tested by the method prescribed in IS 12235(Part 13), the tensile strength at yield shall not be less than 50 MPaat 27±2°C. )	-
7.1,7.1.1 IS 12235 (Part 1) Table 2 (Outside Diameter at any point)	-
7.1.2 IS 12235 (Part 1) Table 2 (Wall Thickness )	-

-
The following test facilities are not available: (1) Verification of the Malfunction temperature Cl 6.3.2 (2) Effect on water Cl.9.3 (3) Hyd. characteristics Cl.10.1 for 165 Hr and 1000 Hr (4) thermal stability test.Cl.10.2

162

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

3450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1,6.1.1 IS 12235 (Part 1) Table 1 (Dimension of Pipes: Mean outside Diameter, dem)	-
6.1,6.1.1 IS 12235 (Part 1) Table 1 (Outside Diameter at any point, de)	-
6.1.2 IS 4985 Table 2 (Wall Thickness, e )	-
6.1.4, Table 3 (Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-
6.1.4, Table 3 (ii) Min. depth of engagement, A. )	-
6.1.4 Table 3 (iii) Depth of sealing Zone C )	-
6.1.4, Table 3 (iv) Length of spigot, l1)	-
6.1.4, Table 3 (v) Chamfer length, H : Approx.)	-
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-
6.1.4, Table 4 (b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-
6.1.4, Table 4 (ii) Length of Solvent Cement socket, l2 )	-
6.1.4, Table 4 (iii) Length of spigot, l1, 100 mm Min.)	-
6.1.4, Table 4 (iv) Chamfer length, H, 7 mm Approx.)	-
7.3 IS 1223S ( Part 2) (Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-
7.4 IS 1223S ( Part 5) (Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6 (Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-
6.1.3 (Length of Pipe)	-
8.1 Annex B (Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-

-
The following test facilities are not available: (1) Ring Stiffness (2)Elastomeric Sealing ring (3)Internal Hydrostatic Pressure for sealing ring joints (4)Intenal negative hydrostatic pressure set up. (5)Effect on water (6) TF above 250 mm

163

IS 14899 (2014)

Liquefied petroleum gas (LPG) containers for automotive use - Specification (First Revision)

21363 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
10.1.5 (Inner surface in tension)	-
10.1.5 (Outer surface in tension)	-
10.1.8 (Water Capacity)	-
10.1.6 (Macroscopic Examination On Circumferential Weld )	-
10.1.6 (Macroscopic Examination On longitudinal Weld)	-
10.1.6.1 (Macroscopic Examination, m1,Through valve boss )	-
10.1.6.1 (Macroscopic Examination, m2,Through valve plate welds)	-
11 (Surface coating and colour)	-

-
Test facilities are not available for the following: (1) ( Cl. 10.5.1) - Radiographic examinations, (2) (Cl.10.6.1) Bonfire test, (3) (Cl.10.6.3) - Crash test, (4) (cl.10.6.2) - Fatigue Test (5) Chemical composition( Ni, Cr, N )

164

IS 13997 (2014)

Drums, large open top - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5, Table 1 (Dimensions-D2)	-
5, Table 1 (Dimensions-D3)	-
5, Table 1 (Dimensions-D4)	-
5, Table 1 (Dimensions-H1)	-
5, Table 1 (Dimensions-H5)	-
5, Table 1 (Dimensions-h2)	-
5, Table 1 (Dimensions-h3)	-
5, Table 1 (Dimensions-h4)	-
5, Table 1 (Dimensions-p1)	-
6.2 (The nominal thickness of steel sheets for body and ends )	-
7.2 ( CONSTRUCTION)	-
7.3 ( CONSTRUCTION- Double Seam/Spiral Seam/Triple Seam Construction for Grade A Drums)	-
7.4 ( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums)	-
7.4 ( CONSTRUCTION-Spiral Seam/Triple Seam Construction for Grade B Drums-Seam rolling layers)	-
7.5 ( CONSTRUCTION)	-
7.6 ( CONSTRUCTION)	-
7.7 ( CONSTRUCTION)	-
7.8 ( CONSTRUCTION- crest to trough gap)	-
7.8 ( CONSTRUCTION- no of corrugations on the body Each side)	-
7.9 (Closures)	-
7.10(a) (Closures)	-
7.10(b) (Closures)	-
7.10(c) (Closures)	-
7.10(d) (Closures)	-
7.11 ( Locking Ring)	-
8.1 (FINISH )	-
9 (leakage test)	-

-
-

165

IS 13983 (1994)

Stainless Steel Sinks For Domestic Purposes

Rs.14635/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6 (Thickness of sheet/strip)	-
6 (Depth of bowl)	-
6 (Internal dimensions of the bowl)	-
6 (Bowl locating limits)	-
6 (Co-ordinating sizes)	-
7.5 (Tap holes)	-
7.6 (Overflows)	-

-
Test facilities are not available for the following: 1. Ni, Cr, Nitrogen as per IS 5522

166

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

Rs.4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.2 (Flow path in emitters)	-
7.3.1 (Resistance to Hydrostatic pressure)	-
7.3.2 (Resistance to Hydrostatic pressure)	-
7.1 (Construction and workmanship)	-
7.4.2 (Emitter Pull Out On-line emitters)	-
8.1.2 (Uniformity of Emission Rate Unregulated emitters)	-
8.2.2 (Emission rate as a function of inlet pressure Unregulated emitters)	-
8.3 (Determination of Emitter Exponent)	-
4 (Classification)	-

-
-

167

IS 13422 (1992)

Disposable surgical rubber gloves specification

Rs.6900.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.2.2 and Table 1 Fig. 1 (Dimensions - Length)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Width)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Finger)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Palm)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Cuff)	-
5.3 and Table 2 ( Tensile Strength Before Ageing)	-
5.3 and Table 2 ( Elongation at Break Before Ageing)	-
5.3 and Table 2 (Stress at 500% Elongation at Break Before Ageing)	-
5.3 and Table 2 ( Tensile StrengthAfter Accelerated Ageing)	-
5.3 and Table 2 ( Elongation at Break After Accelerated Ageing)	-
5.5 (Airtight Test)	-
4 (TYPES)	-
5.2.2 and Table 1 Fig. 1 (Dimensions - Thickness of Cuff)	-
5.3 and Table 2 (Stress at 500% Elongation at Break Before Ageing)	-
5.2.1 (General Characteristics and Dimensions)	-

-
-

168

IS 15962 (2012)

Structural steels for buildings and structures with improved seismic resistance

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clauses 7, 8.1 & .2, Table- 1 (E250S, C)	-
Clauses 7, 8.1 & .2, Table- 1 (E250S, Mn )	-
Clauses 7, 8.1 & .2, Table- 1 (E250S, P)	-
Clauses 7, 8.1 & .2, Table- 1 (E250S, S)	-
Clauses 7, 8.1 & .2, Table- 1 (E250S, Si)	-

-
Test facilities are not available for the following: 1. Chemical Composition ( Cr, Mo, Ni, Al, Microalloying element, N, Cu)

169

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

Total Testing Charges : Rs. 9970.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-
Cl.14, Annex A (Titanium Di-Oxide Content)	-
Cl.15, Annex B (Sulphated Ash Content)	-
7.1,Table 1 (Wall thickness)	-
7.2 ,Table 2&3 (Socket Dimensions)	-
7.3 (Dimensions of waste trap(Nahani Trap)	-
8 (Sealing Rings)	-
11.4,Table 5 (Vent cowl)	-
12.2 (Stress relief test)	-
12.3 (Vicat softening tempewrature)	-
16.1 (Impact test)	-
17 (Watet tightness of joint)	-
Cl 12.4 (Effect on Water Lead (first extraction))	-
Cl 12.4 (Effect on Water Lead (third extraction))	-
Cl 12.4 (Effect on Water Dialkyl tin C4 and higher homologues(measured as tin )(third extraction ))	-
Cl 12.4 (Effect on Water Cadmium (mean of first extraction, second extraction and third extraction))	-
Cl 12.4 (Effect on Water Mercury (mean of first extraction, second extraction and third extraction))	-

-
Remark : a sealing ring-prepared button piece is required to measure the IRHD harness.

170

IS 12337 (1988)

Specification for manually operated fertilizer broadcaster

Rs 600/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.9 (Constructional Requirements- Total Mass)	-
5 (Capacity)	-
4.1 (Constructional Requirements- Hopper)	-
4.1.1 (Constructional Requirements- Hopper)	-
4.2 (Constructional Requirements- Spreading Disc)	-
4.4 (Constructional Requirements- Agitator)	-
4.6 (Constructional Requirements- Crank)	-
4.7 (Constructional Requirements- Straps)	-
4.7 (Constructional Requirements- Straps (cushion width))	-
4.9 (Constructional Requirements- Total Mass)	-

-
-

171

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

Rs 2850 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 8.1, 8.1.1 & 10.1 Table 1 (Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
9.3 (Tensile Test-1608:Part 1)	-
9.3, Table 3 (Yield Strength, Mpa)	-
9.3, Table 3 (Elongation, %)	-
9.4 (Erichsen Cupping Test,(Average depth of cupping) mm)	-
11 (Surface finish)	-
12 (Dimensions)	-
14.1 (Thickness,mm)	-
14.2 ( Width, mm)	-
14.3 (Length, mm)	-
14.4 (Flatness, mm)	-
14.5 (Camber)	-
17 (Marking)	-

-
Test facilities are not available for the following: 1. Ni, Cr, Cu, N, 2. Erichsen Cuppling Machine

172

IS 11313 (2007)

Hydraulic power sprayers - Specification (First Revision)

13350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5 (CONSTRUCTION REQUIREMENTS)	-
5 (CONSTRUCTION REQUIREMENTS)	-
6.1 (Discharge Rate/Suction Capacity)	-
6.2 (Volumetric Efficiency)	-
6.4 (Maximum Achievable Pressure)	-
6.5 (Endurance Test)	-

-
-

173

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

Rs.1800/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.2.1, Table-1, Fig-1 (B)	-
3.2.1, Table-1, Fig-1 (Minimum wall thickness for working pressure)	-
3.2.1, Table-1, Fig-1 (Plumbing)	-
Clause 3.2.2, and Fig. 2. (B)	-
Clause 3.2.2, and Fig. 2. (Minimum wall thickness for working pressure)	-
3.2.2, and Fig. 2 (Dimensions of Socket for Elastomeric Sealing Ring Joint)	-

-
The following test facilities are not available: (1)Effect on water (2) Testing facility above 250 mm for Short Term Hydrostatic test

174

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

Rs 1500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 Table-1 Fig.1 (Dimension of Socket length)	-
6.1 (Opacity test in accordance with IS 12235 (Part 3))	-
6.2 (Short Term Hydraulic Test in accordance with Annex A)	-

-
The following test facilities are not available: (1)Effect on water (2) Testing facility above 250 mm for Short Term Hydrostatic test

175

IS 9798 (2013)

Low pressure regulators for use with liquefied petroleum gas (LPG) - Specification (Second Revision)

14276 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3.2 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
4.3.5ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Diaphragm: Extractable )	-
4.3.3 (Clamping test)	-
4.3.5aii Annex D (Diaphragm: Absorbed)	-
4.3.5b IS 3400(Part 2) (Changes in hardness, before and after the immersion )	-
4.4.2ai Annex D (The material shall, after immersion in n-pentane or octet commercial LPG for 72 h, meet the appropriate requirements specified in Annex D Extractable )	-
4.4.2b IS 3400(Part 2) (Changes in hardness, before and after the test)	-
4.4.3 IS 3400(Part 4) (The material shall not show change of more than 10 IRHD when subjected to ageing of 72 h at 70°C in accordance with the method prescribed in 3 or 4 of IS 3400 (Part 4))	-
5.5.1 (Hydrostatic PressureTest)	-
5.5.2 (Pneumatic PressureTest)	-
5.6,5.6.1 Fig 2A/ Fig 2B (Outlet Connection:- Non-threaded Outlet Connection)	-
6,6.1,6.2 (SOUNDNESS)	-
8.9 (Performance (Before Cycle test, Low Temp. Test and High Temp. Test) Inlet Pressure Flow Rate )	-
8.9 (0.5 kgf/cm2 100 % )	-
8.9 (17 kgf/cm2 10 % )	-
8.9 (Static(lock up) pressure)	-
8.10.3 Annex H 8.9 (High Temperature Test Performance test after exposure to temperature at 650 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-
8.10.2 Annex H 8.9 (Low Temperature Test Performance test after exposure to temperature at -200 C for 10 Min and back to ambient condition. Inlet Pressure Flow Rate)	-

-
Test facilities are not available for the following: a) Mechanical strength of connections, Cl. 8.11 b) Compression set test for Rubber components c) Test Bench as per Annex K

176

IS 9295 (1983)

Specification for steel tubes for idlers for belt conveyors (First Revision)

Rs 5100/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
7.1 (Sulphur- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
7.1 (Phosphorous- Relevant Parts of IS 228 or any other established instrumental/chemical method)	-
8.1.1 Table 1 (Tensile Strength- IS 1608(1))	-
8.1.1 Table 1 (Yield Strength- IS 1608)	-
8.2 (Drift Expansion Test- IS 2335)	-
8.3 (Flattening Test- IS 2328)	-
9.1 Table 2 (Outside Diameter)	-
9.1 Table 2 (Thickness)	-
9.1 Table 2 (Mass)	-
10 (Hardness)	-
13.1.1 (Ovality)	-
13.1.2 (Eccentricity)	-
15.1 (Straightness)	-
16.1 (Length)	-

-
Test facilities are not available for the following: 1.Except Drift Expansion

177

IS 8737 (2017)

Valve fittings for use with liquefied petroleum gas (LPG) cylinders for more than 5 litre water capacity - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.2.1Sl.No.i (Copper)	-
4.4 (Izod impact strength-IS 1598)	-
9.2a (Cycle Test)	-
9.5bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
4.3.1a (Tensile Strength-IS 1608)	-
4.3.1b (Elongation-IS 1608)	-
7.10 (The minimum finished wall thickness at any portion of the valve shall not be less than 2.5 mm)	-
9.3 (Operation Test)	-
9.5bii (Pneumatic Test ,after cycle test: Tightness of Valve Spindle and Valve Housing)	-
9.5biii (Pneumatic Test ,after cycle test: Tightness of Joint Packing and Housing)	-
8.3.1 (Pneumatic Test: Tightness of Joint Packing (in Valve Outlet) and Valve Spindle)	-
8.3.2 (Pneumatic Test: Tightness of Valve Spindle and Valve Housing)	-
8.3.3 (Pneumatic Test: Tightness of Joint Packing and Housing)	-

-
"1.Cycles test 2. Security Cap /Nut 3. Spring a) Load Test b)Permanent set test c)Rust proofness of spring"

178

IS 8423 (1994)

Specification for controlled percolating hose for fire fighting

Rs. 4200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.4.1.1 (The nominal internal diameter of hose shall be 38, SO, 63 and 70 rom.The internal diameter of the hose shall be measured by a suitable tapered plug gauge, and shall conform to the specified diameter within a tolerance of + 2·0 mm. -0'0)	-
Cl.5. (The hose length shall be 30 m or of such length as required.)	-
Cl.6 (The hose shall be flexible and on being machine coiled, the diameter of the coil of 30 m hose shall not exceed 45 em for all slzes in dry state without coupling. The coil diameter shall be measured at the widest part of the coil.)	-
Cl.7 (The average mass oC hose per metre shall not be more than that prescribed in Table 1. For determination of mass, sample of the hose shall be conditioned at 27 ± 2°C and 65 ± 5 percent relative humidity Cor a period of at least 48 hours and then shall be weighed under same conditions.)	-
Cl.8 (The percolation, when tested in accordance with the procedure laid down in 8.1.1 shall not exceed the limits prescribed in Table 2.)	-
Cl.9 (The full length sample of the dry hose is connected to the pump fitted with water and pressure built up to. 7 kaf/cn,' (70 N/cm' ) steadily over a period of two minutes. After the hose has been at pressure 7 kif/em' ( 70 NIemi) for a period of S minutes, a visual inspection I is made of the length to ascertain the evenness and degree of wetting out along the complete length of hose and at least 75 percent of the hose jacket shall be evenly and consistently wetted out in this manner.)	-
Cl.10 (Full length of hose shall be subjected to an internal hydraulic pressure of 2'1 MPa (21'4 kgf/ems ) at the rate of I MPa ( 10'2 kaf/em· )/ minute in ac.cordance with 1.3 of IS 443 : 191~ and maintained for a period of one minute. During this test. the hose shan not show breakage of yarn.)	-

-
-

179

IS 7887 (1992)

Mild steel wire rod for general engineering purposes - Specification (First Revision)

Rs.7200/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 9 (Nominal Diameter & Out Of Shape)	-
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-

-
Test facilities are not available for the following: 1. Chemical composition (Al)

180

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

Rs.2700/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
cl 2.2.2 (Dimensions)	-

-
The following test facilities are not available: 6.3 Effect on water

First
Prev
5
6
7
8
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List