BIS - LIMS (Laboratory Information Management System)

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List

Reset

259 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

121

IS 3906 (1995)

Crop Protection Equipment - Hand-operated Knapsack Sprayer, Piston Type

3310.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
9.1 (Marking)	-
5.1 & 5.2 (a) Discharge rate ml/minute Min. )	-
5.1 & 5.2 (b) Volumetric efficiency 85% Min.)	-
6.1 (i) Capacity Liters )	-
6.1 (ii)Thickness Min.)	-
6.1 (iii)The tank, when filled up to its neck level with water, shall not show any sign of leakage and shall not buckle)	-
6.2 (b)Skirt/Stand)	-
6.3 (c) Straps )	-
6.4 (d) Filling hole)	-
6.9 (i) Operating lever, handle and piston rod )	-
6.1 (j) Discharge outlet)	-
6.13 (m) cut off device and lance )	-
6.14 (n) Nozzle )	-
6.16 (p) Mass )	-
6.17 (q) Endurance)	-
Cl.8.1 and 8.2 (6. Workmanship & finish)	-
Cl.8.1 and 8.2 (Cut off device)	-

-
-

122

IS 3652 (1995)

Crop protection equipment. - Foot sprayer - Specification (Fourth Revision)

Testing charges for the product are Rs. 8550/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
C-10 (MARKING)	-
C-1 (TYPES)	-
C-2 (DIMENSIONS)	-
C- 6.1 to 6.3 (OPERATING TRIGGER/Knob)	-
D-3 (a) Wall thickness)	-
D-3 (b) Internal dia of tube)	-
D-3 (c)Length of lance)	-
D-4 (Nozzle)	-
C-3 (STRAINER)	-
F-3 (PERFORMANCE REQUIREMENTS)	-

-
-

123

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.0 (Workmanship)	-
19.1.1, 24.1.1, 28.1.1, 33.1.1 (Dimensions- Outside Dia)	-
19.1.2, 24.1.2, 28.1.2, 33.1.2 (Dimensions- Thickness)	-
13.1.3 (Tensile Strength)	-
13.1.1 (Yield Stress)	-
13.1.2 (Elongation)	-
13.2 (Flattening Test)	-
13.5 (Drift Expansion Test)	-
6.0 (Workmanship)	-
4.1 (Sulphur-Percentage by mass)	-
4.1 (Phosphorus-Percentage by mass)	-

-
Test facilities are not available for the following: 1. Bend Test 2. Drift Expansion Test 3. Crushing Test 4 For sizes above 200 mm

124

IS 3196 : Part 1 (2013)

Welded low carbon steel cylinders exceeding 5 litres water capacity for low pressure liquefiable gases: Part 1 cylinders for liquefied petroleum gases (Lpg) - Specification (Sixth Revision)

14900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
20 (Marking)	-
9 (Valve Protection)	-
10 (Foot Ring)	-
14 (Bung)	-
14 (Water Capacity)	-
15 (Hydrostatic Test)	-
17 (Burst Test under Hydraulic Pressure)	-
18 (Parent Metal Longitudinal Tensile Strength)	-
18 (Parent Metal Circumferential Tensile Strength)	-
18 (Weld Metal Tensile Strength)	-
18 (Bend Test across weld)	-
18 (Root Bend Test)	-
18 (Face Bend Test)	-
18 (Macro Examination)	-
18 (Minimum Thickness Test)	-
21 (Colour Identification)	-
23.2 (Protective Coatings)	-
20.0 (Marking)	-
20 (Marking)	-

-
Test facilities are not available for the following: 1.Cycle Test 2. Impact and Drop Test 3.Radiographical Examination

125

IS 2548 : Part 1 (1996)

Plastic seats and covers for water - Closets - Specification: Part 1 thermoset seats and covers (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl.9.1 (Strength Requirements for Seats The seats shall withstand, without permanent distortion of the seat or the hinge fittings or damage to any finish, a load of 1150 N applied in the manner prescribed in Annex A for a period of 30 minutes.)	-
Cl.9.3 (Water Absorption When tested according to Annex D, the increase in mass shall be 2.26 percent, Max and on visual inspection after immersion, it shall show no impairment in respect of the characteristics specified under 5.2.)	-
Cl.9.4 (Cl 9.4.1 ) (Rigidity Seat When tested in accordance with Annex E, the maximum deflection shall be 12.5 mm and, on visual inspection after the load is removed, the scats shall not show any fracture.)	-
Cl.9.4 (Cl 9.4.2 ) (Cover When tested in accordance with Annex F, the maximum deflection shall be 25 mm, and on visual inspection after the load is rcmovcd, )	-
Cl.9.4 (Cl 9.4.3 ) (When tcstcd in accordance with Annex G, the maximum distortion shall be 3 mm.)	-
Cl.5.2 (FinishThe surfaces of the seats, covers and components shall be smooth, free from blisters and delamination and reasonably free from flowlines, contamination, streaking and unintended colour variation.)	-
Cl.6.1 (Seat The seat shall conform to the dimensions given in Table 1 and Fig. 1. In the case of open front design,)	-
Cl.6.2 (The cover shall conform to the dimensions given in Table 1 and Fig. 1.)	-
Cl 7.1 (The bolts shall have a minimum shank length of 65 mm .)	-
Cl 7.1 (The bolts shall have a coarse thread of M8 size in accordance with IS 4218 (Part 6) : 1978 within 25 mm of the flange for fixing to the pan)	-
Cl 7.1 ( Each bolt shall be provided with TWO suitably shaped washers of rubber or other equivalent material for adjusting the level of theseat when securing it to the pan. The maximum external measurement of any such washers fixed on the underside of the pan shall be not greater than 25 mm.)	-
Cl 7.1 (In addition, one washer made of any other material specified for bolts and not exceeding 2.5 mm in diameter shall be provided with each bolt.)	-
Cl.7.1.2 (Hinging pins, where used, shall be not less than 5 mm in diameter.)	-
Cl.8.1 (Each seat shall be provided with not less than three rubber or plastic buffers of size 25 mm x 40 mm x 10 mm for closed front seats)	-
Cl.9.2 (Seat When tested in accordance with Annex B, the seat, buffers and hinges shall not show any visible damage.)	-
Cl.9.2 (Cover When tested in accordance with Annex C, the cover, buffers and hinges shall not show any visible damage.)	-
Cl.9.4 (Cl 9.4.2 ) (the covers shall not show any fracture. No part of the edge of the cover shall be pushed through the seat opening.)	-
Cl.9.5 (Staining by Seats and CoversWhen tested in accordance with Annex H,thcrc shall not be any visible colour transfer to the white cloth.)	-
Cl.9.6 (Staining and/or Other Surface Deterioration of Seats and.Covers When tcstcd in accordance with Annex J, there shall not be any changes of colour or other adverse change in surface characteristics.)	-
Cl.9.7 (Endurance Test for Seat, Covers and Buffers When tested in acn)rdance with Annex K, neither scat, cover or buffer’ should bc damaged nor dislocated. This is a type test to be done once in six months.)	-
Cl.9.6 (Staining and/or Other Surface Deterioration of Seats and.Covers When tcstcd in accordance with Annex J, there shall not be any changes of colour or other adverse change in surface characteristics.)	-

-
-

126

IS 319 (2007)

Free cutting brass bars, rods and section - Specification (Fifth Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.0 (Freedom from defects)	-
7.0 (Dimension and Tolerances)	-
9.1 Table-2 (Tensile Strength)	-
9.1 Table-2 (Elongation)	-
10.1 (Mercurous Nitrate Test)	-
9.2 (Vickers Hardness)	-

-
Test facilities are not available for the following: 1. Cu, Pb, Fe, Zn

127

IS 1835 (1976)

Specification for round steel wire for ropes (Third Revision)

Rs 4500/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (Workmanship)	-
Cl 10 (Diameter)	-
Cl 11.2 (Workmanship)	-
Cl 12.2 (UTM)	-
Cl 12.3 (Torsion)	-
Cl 12.4 (Reverse Bend)	-
Cl 12.5 (Wrap)	-
Cl 12.6 (Adhesion )	-
Cl. 5.1, T-1 (C)	-
Cl. 5.1, T-1 (Mn)	-
Cl. 5.1, T-1 (Si)	-
Cl. 5.1, T-1 ( Grade 3) (P)	-
Cl. 9.1, T-3 (Mass of Zinc Coating)	-
Cl. 5.1, T-1 ( Grade 1) (S)	-
Cl. 5.1, T-1 ( Grade 2) (S)	-
Cl. 5.1, T-1 ( Grade 3) (S)	-
Cl. 5.1, T-1 ( Grade 4) (S)	-
Cl. 5.1, T-1 ( Grade 5) (S)	-
Cl. 5.1, T-1 ( Grade 1) (P)	-
Cl. 9.1, T-3 (Uniformity)	-
Cl. 5.1, T-1 ( Grade 3) (P)	-
Cl. 5.1, T-1 ( Grade 4) (P)	-
Cl. 5.1, T-1 ( Grade 5) (P)	-

-
Test facilities are not available for the following: 1. Cu, Ni, Cr

128

IS 513 : Part 2 (2016)

Cold reduced carbon steel sheet and strip: Part 2 high tensile and multi - Phase steel (Sixth Revision)

Please see remarks View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 7 (UTM)	-
Cl 8.5 (Workmanship)	-
Cl 8.6 (Workmanship)	-
Cl 9 (Workmanship)	-
Cl 10 (Length, Width & Thickness)	-
Cl 7 (UTM)	-
6.0 (SILICON)	-
6.0 (MANGANESE)	-
6.0 (PHOSPHORUS)	-
6.0 (SULPHUR)	-
6.0 (CARBON)	-

-
Test facilities are not available for the following: 1. Al, Nitrogen, Chromium, Nickel, Niobium, Vanadium, Titanium, Molybdenum,Boron, Calcium and others 2. Tensile Strain Hardening Component 3. Surface finish

129

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

Rs.8850/- Excluding Tensile Strain Hardening component View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (UTM)	-
Cl 9 (Workmanship)	-
Cl 9.6 (Workmanship)	-
Cl 10 (Workmanship)	-
Cl 11 (Length, Width & Thickness)	-
7.0 (SILICON)	-
7.0 (MANGANESE)	-
7.0 (PHOSPHORUS)	-
7.0 (SULPHUR)	-
7.0 (CARBON)	-

-
Test facilities are not available for the following: 1. Aluminium, Micro-alloying elements 2. Tensile Hardneing component 3. Bake Hardneing test 4. Cupping Test 5. Surface finish 6.Plastic Strain Ratio (r bar/r-90)

130

IS 15410 (2003)

Containers for packaging of natural mineral water and packaged drinking water - Specification

Total charges = Rs.5850.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.6.2 (TRANSPARANCY)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- b. Vibration leakage)	-
4.6.4 (DROP TEST)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- c. Air pressure leakage)	-
4.6.3, clause 6 of IS:2798:1998 (Leakage test- a. Closure leakage )	-
4.5, IS:2798:1998 (Wall thickness- Bottom, in mm)	-
4.5, IS:2798:1998 (Wall thickness- Middle , in mm)	-
4.5, IS:2798:1998 (Wall thickness- Top , in mm )	-
4.3 (Workmanship, Finish & Appearance)	-
4.2 (Design, Shape & Dimension )	-
4.6.5.1 (chem) (Colour migration (Caps))	-
4.0 (chem) (MATERIAL)	-
4.6.6 (chem) (Water Potability test (after 30 days) (a) Taste (b) Odour)	-
4.6.5 , IS:9845:1998 (chem) (Migration- b. Amount of extractive)	-
4.4 (chem) (Brimful capacity)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (i) (Barium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ii) (Cobalt)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iii) (Copper)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iv) (Iron)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (v) (Lithium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vi) (Manganese)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vii) (Zinc)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (viii) (Antimony)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (i) (Barium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (ii) (Cobalt)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vi) (Manganese)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iii) (Copper)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (iv) (Iron)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (v) (Lithium)	-
Cl.4.6.7.2 and 4.6.7.3, Table 3, (vii) (Zinc)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (viii) (Antimony)	-
CL 4.6.7.2 and 4.6.7.3, Table 3 (ix) (Phthalic acid, bis(2-ethylhexyl) ester (DEHP))	-

-
-

131

IS 15500 : Part 1 to 8 (2004)

Deepwell handpumps, components and special tools - Specification

Rs 4500/- + Charges as per relevant material standards View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
2/2.3,(Refer 15500(Part 1 to 8)& 9.4 (Part 1) (Dimensions & critical dimensions in conformance with the relevant figures in Part 4.)	-
2/2.3,(Refer fig 4.1 of Part4) & 9.4 (Part 1) (Dimensions of FIG.4.1 HEAD— STANDARD(For SDWP, VLOM-65 and VLOM-50))	-
2/2.3,(Refer fig 4.2 of Part4) (Dimensions of FIG. 4,2 HEAD— EWDP)	-
2/2.3,(Refer fig 4.3A of Part4) (Dimensions of Fig 4.3A Side Plate)	-
2/2.3,(Refer fig 4.3B of Part4) (Dimensions of Fig 4.3B Head Flange)	-
2/2.3,(Refer fig 4.3C of Part4) (Dimensions of Fig 4.3C Back Plate —Standard (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3D of Part4) (Dimensions of Fig 4.3D Bracket — Standard (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3E of Part4) (Dimensions of Fig 4.3E Back Plate — EDWP)	-
2/2.3,(Refer fig 4.3F of Part4) (Dimensions of Fig 4.3F Bracket — EDWP)	-
2/2.3,(Refer fig 4.3G of Part4) (Dimensions of Fig 4.3G Axle Bust — Right)	-
2/2.3,(Refer fig 4.3H of Part4) (Dimensions of Fig 4.3H Axle Bust — Left)	-
2/2.3,(Refer fig 4.3I of Part4) (Dimensions of Fig 4.3 I Front Top End Plate)	-
2/2.3,(Refer fig 4.3IJof Part4) (Dimensions of 4.3J Front Bottom End Plate)	-
2/2.3,(Refer fig 4.3IKof Part4) (Dimensions of Fig 4.3K Gusset — Standard w (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.3L Jof Part4) (Dimensions of Fig 4.3L Gusset — EDWP (For EDWP) )	-
2/2.3,(Refer fig 4.4 Jof Part4) (Dimensions of FIG. 4.4 FRONTCOVER)	-
2/2.3,(Refer fig 4.5A of Part4) (Dimensions of FIG. 4.5A Flange for Third Plate)	-
2/2.3,(Refer fig 4.5 B of Part4) (Dimensions of FIG. 4.5B Guide Bush )	-
2/2.3,(Refer fig 4.6 of Part4) (Dimensions of FIG.4.6 HANDLE— STANDARD (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.7 of Part4) (Dimensions of FIG.4.7 HANDLE— EDWP)	-
2/2.3,(Refer fig 4.8A of Part4) (Dimensions of FIG 4.8A Handle Bar — Standard (For SDWR VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.8B of Part4) (Dimensions of FIG 4.8B Handle Bar — EDWP)	-
2/2.3,(Refer fig 4.8C of Part4) (Dimensions of FIG 4.8C Chain Guide)	-
2/2.3,(Refer fig 4.8 D of Part4) (Dimensions of Fig 4.8D Bearing Housing )	-
2/2.3,(Refer fig 4.9 of Part4) (Dimensions of FIG. 4.9 CHAIN WITH COUPLING)	-
2/2.3,(Refer fig 4.10 of Part4) (Dimensions of FIG. 4.10 T-BAR (For EDWP only))	-
2/2.3,(Refer fig 4.11 of Part4) (Dimensions of FIG; 4.11 COUNTER WEIGHT (For EDWP only))	-
2/2.3,(Refer fig 4.12A of Part4) (Dimensions of Fig 4.1 2A Telescopic Stand — Standard (For borewell with 150 NB casing pipe)(For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.12B of Part4) (Dimensions of Fig 4.12B Normal Stand — Standard (For borewell with 1001125 NB casing pipe) (For SDWP, VLOM-65 & VLOM-50))	-
2/2.3,(Refer fig 4.13A of Part4) (Dimensions of Fig 4.1 3A Telescopic Stand — EDWP (For borewell with 150 NB casing pipe) FOR EDWP )	-
2/2.3,(Refer fig 4.13B of Part4) (Dimensions of Fig 4.1 3B Normal Stand — EDWP (For borewell with 100/125 NB casing pipe) FOR EDWP )	-
2/2.3,(Refer fig 4.14 A of Part4) (Dimensions of Fig 4.1 4A Stand Pipe — Standard (For SDWP, VLOM-65, VLOM-50))	-
2/2.3,(Refer fig 4.14 B of Part4) (Dimensions of Fig 4.14B Stand Pipe — EDWP (For EDWP))	-
2/2.3,(Refer fig 4.14 C of Part4) (Dimensions of Fig 4.14C Stand Flange)	-
2/2.3,(Refer fig 4.14 D of Part4) (Dimensions of Fig 4.14D Leg)	-
2/2.3,(Refer fig 4.14 E of Part4) (Dimensions of Fig 4.14E Gusset)	-
2/2.3,(Refer fig 4.14 F of Part4) (Dimensions of Fig 4.1 4F Reducer Coller)	-
2/2.3,(Refer fig 4.14 G of Part4) (Dimensions of Fig 4.14G Spike)	-
2/2.3,(Refer fig 4.18A of Part4) (Dimensions of FIG. 4.1 8A Tank Pipe )	-
2/2.3,(Refer fig 4.18B of Part4) (Dimensions of FIG. 4.18B Tank Top Flange)	-
2/2.3,(Refer fig 4.18C of Part4) (Dimensions of FIG. 4.18C Spout)	-
2/2.3,(Refer fig 4.18D of Part4) (Dimensions of FIG 4.1 8D Gusset)	-
2/2.3,(Refer fig 4.18E of Part4) (Dimensions of FIG 4.18E Tank Bottom Flanae — 32 (For SWDP & EDW~))	-
2/2.3,(Refer fig 4.18F of Part4) (Dimensions of FIG 4.1 8F Riser Pipe Holder — 32 (For SWDP & EDWP))	-
2/2.3,(Refer fig 4.18G of Part4) (Dimensions of FIG 4. 18G Riser Pipe Holder — 50)	-
2/2.3,(Refer fig 4.18H of Part4) (Dimensions of FIG 4.1 8H Tank Bottom Flange — 50)	-
2/2.3,(Refer fig 4.18I of Part4) (Dimensions of FIG 4.18I Tank Bottom Flange — 65 )	-
2/2.3,(Refer fig 4.18J of Part4) (Dimensions of FIG 4.18J Riser Pipe Holder — 65 )	-
2/2.3,(Refer fig 4.20 A of Part4) (Dimensions of FIG 4.20A Cone Flange)	-
2/2.3,(Refer fig 4.20 B of Part4) (Dimensions of FIG 4.20B Steel Cone)	-
2/2.3,(Refer fig 4.21 of Part4) (Dimensions of FIG. 4.21 CONNECTING ROD)	-
2/2.3,(Refer fig 4.22of Part4) (Dimensions of FIG. 4.22 PLUNGER ROD — STANDARD (For SDWP))	-
2/2.3,(Refer fig 4.23of Part4) (Dimensions of FIG.4.23 PLUNGERROD — LONG (For EDWP, VLOM-65 & VLOM-50 ))	-
2/2.3,(Refer fig 4.24of Part4) (Dimensions of FIG. 4.24 HANDLEAXE )	-
2/2.3,(Refer fig 4.25 of Part4) (Dimensions of FIG. 4.25 PUSHROD )	-
2/2.3,(Refer fig 4.26 of Part4) (Dimensions of FIG. 4.26 BEARINGSPACER)	-
2/2.3,(Refer fig 4.27 of Part4) (Dimensions of FIG.4.27 WASHER)	-
2/2.3,(Refer fig 4.28 of Part4) (Dimensions of FIG. 4.28 SOCKET— 32 (For SDWP & EDWP))	-
2/2.3,(Refer fig 4.29 of Part4) (Dimensions of FIG. 4.29 SOCKET— 50 (For VLOM-50))	-
2/2.3,(Refer fig 4.30 of Part4) (Dimensions ofFIG. 4.30 SOCKET— 65 (For VLOM-65))	-
2/2.3,(Refer fig 5.1 of Part 5) (Dimensions of FIG. 5.1 CYLINDER BODY— STANDARD (For SDWP))	-
2/2.3,(Refer fig 5.2 of Part 5) (Dimensions of FIG. 5.2 CYLINDERBODY— LONG (For EDWP & VLOM-65))	-
2/2.3,(Refer fig 5.3 of Part 5) (Dimensions of FIG. 5.3 CYLINDERBODY— VLOM-50)	-
2/2.3,(Refer fig 5.4 of Part 5) (Dimensions of FIG. 5.4 REDUCERCAP (For SDWP & EDWP) )	-
2/2.3,(Refer fig 5.5A of Part 5) (Dimensions of FIG. 5.5 A CYLINDERCAPS— VLOM-65 (For SDWP & EDWP))	-
2/2.3,(Refer fig 5.5B of Part 5) (Dimensions of FIG. 5.5 BCYLINDERCAPS— V LOM-65 (For SDWP & EDWP))	-
2/2.3,(Refer fig 5.6 of Part 5) (Dimensions ofFIG. 5.6 CYLINDERCAPS— VLOM-50)	-
2/2.3,(Refer fig 6.1 of Part 6) (Dimensions of FIG. 6.1 A BRASS LINER)	-
2/2.3,(Refer fig 6.1 of Part 6) (Dimensions of FIG. 6.1 B BRASS LINER)	-
2/2.3,(Refer fig 6.1 of Part 6) (Dimensions of FIG. 6.1 C BRASS LINER)	-
2/2.3,(Refer fig 6.2 of Part 6) (Dimensions of FIG. 6.2 PLUNGERYOKE BODY (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 6.3 of Part 6) (Dimensions of FIG. 6.3 UPPERVALVE (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 6.4 of Part 6) (Dimensions of FIG. 6.4 BUCKETSPACER— STANDARII (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 6.5 of Part 6) (Dimensions of FIG.6.5 BUCKET SPACER — LOWER (For EDWP))	-
2/2.3,(Refer fig 6.6 of Part 6) (Dimensions of FIG. 6.6 FOLLOWER — SDWP )	-
2/2.3,(Refer fig 6.7 of Part 6) (Dimensions of FIG. 6.7 FOLLOWER— EDWP)	-
2/2.3,(Refer fig 6.8 of Part 6) (Dimensions of FIG. 6.8 FOLLOWER— VLOM-65)	-
2/2.3,(Refer fig 6.9 of Part 6) (Dimensions of FIG. 6.9 CHECK VALVE— STANDARD (For SDWP & EDWP) )	-
2/2.3,(Refer fig 6.10 of Part 6) (Dimensions of FIG. 6.10 CHECKVALVE— VLOM-65)	-
2/2.3,(Refer fig 6.11 of Part 6) (Dimensions of FIG. 6.11 RUBBERSEATRETAINER (For SDWP & EDWP))	-
2/2.3,(Refer fig 6.12 of Part 6) (Dimensions of FIG. 6.12 CHECK VALVE SEAT— STAN~AR~ (For SDWP & EDWP))	-
2/2.3,(Refer fig 6.13 of Part 6) (Dimensions of FIG. 6.13 CHECK VALVE — VLOM-65)	-
2/2.3,(Refer fig 6.14 of Part 6) (Dimensions of FIG. 6.14 CAGE (For VLOM-65))	-
2/2.3,(Refer fig 6.15 of Part 6) (Dimensions of FIG. 6.15 PLUNGERVALVE BODY— VLOM-50)	-
2/2.3,(Refer fig 6.16 of Part 6) (Dimensions of FIG. 6.16 CHECKVALVE BODY— VLOM-50)	-
2/2.3,(Refer fig 7.1 of Part 7) (Dimensions of FIG. 7.1 PUMPBUCKET— STANDARD (For SDWP, EDWP & VLOM-65) )	-
2/2.3,(Refer fig 7.2 of Part 7) (Dimensions of FIG. 7.2 PUMP BUCKET — VLOM-50)	-
2/2.3,(Refer fig 7.3 of Part 7) (Dimensions of FIG. 7.3 SEALINGRING— STANDARD (For SDWP & EDWP))	-
2/2.3,(Refer fig 7.4 of Part 7) (Dimensions of FIG. 7.4 SEALING RING— VLOM-65)	-
2/2.3,(Refer fig 7.5 of Part 7) (Dimensions of FIG. 7.5 SEALINGRING— VLOM-50)	-
2/2.3,(Refer fig 7.6 of Part 7) (Dimensions of FIG. 7.6 UPPERVALVE SEATING (For SDWP, EDWP & VLOM-65))	-
2/2.3,(Refer fig 7.7 of Part 7) (Dimensions of FIG. 7.7 LOWERVALVE SEATING— STANDARD (For SDWP & EDWP) )	-
2/2.3,(Refer fig 7.8 of Part 7) (Dimensions of FIG. 7.8 LOWERVALVE SEATING— VLOM-65 68)	-
2/2.3,(Refer fig 7.9 of Part 7) (Dimensions ofFIG. 7.9 BOBBIN (For VLOM-50))	-
2/2.3,(Refer fig 7.10 of Part 7) (Dimensions of FIG. 7.10 O-RING— VLOM-65)	-
2/2.3,(Refer fig 7.11 of Part 7) (Dimensions of FIG. 7.11 O-RING—VLOM-50)	-
2/2.3,(Refer fig 7.12 of Part 7) (Dimensions of FIG. 7.12 RUBBER CONE— VLOM-65 )	-
2/2.3,(Refer fig 7.13 of Part 7) (Dimensions of FIG. 7.13 RUBBERCONE— VLOM-50)	-
2/2.3,(Refer fig 7.14 of Part 7) (Dimensions of FIG. 7.14 PIPE CENTRALIZER— VLOM-65 )	-
2/2.3,(Refer fig 7.15 of Part 7) (Dimensions of FIG.7.15 PIPECENTRALIZER— VLOM-50 )	-
2/2.3,(Refer fig 7.15 of Part 7) (Dimensions of FIG.7.15 PIPECENTRALIZER— VLOM-50 )	-
9.2 of Part1, (Visual Tests)	-
9.4/9.4.1 .2 of part 1 (The stroke of the pump )	-

-
-

132

IS 6528 (1995)

Stainless steel wire - Specification (First Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 6 (Workmanship)	-
Cl 9.1 & Table 3 (Diameter & Out Of Round)	-
Cl 10 (UTM)	-
Cl 10 (UTM)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Silicon)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Manganese)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Phosphorous)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Sulphor)	-
Table-1,( Clauses 7.1, 7.2, 7.3 and 12.1) (Carbon)	-

-
Test facilities are not available for the following: 1. Al, Ni, Cr, Mo, Nitrogen

133

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

Rs.5400/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1, 6.2 (phosphorus)	-
6.1, 6.2 (sulphur)	-
6.1, 6.2 (manganese)	-
6.1, 6.2 (silicon )	-
6.1, 6.2 (carbon)	-
Cl 7 (Workmanship)	-
Cl 8 (Diameter, Ovality & Weight)	-
9.1, table 2 (Tensile Strength)	-
9.1, table 2 (Yield Strength)	-
9.1, table 2 (Elongation)	-
9.2, table 2 (hardness test)	-
12.2 (Bend Test)	-

-
Test facilities are not available for the following: 1, Al, Ni, Cr, Cu, Mo, V, B, Sn 2. Grain size 3. Magnetic Particle 4. Blue Facture Test

134

IS 2802 (1964)

Specification for ice-cream

Rs 7670/- excluding Phosphatase test of mix View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.1 Table 1 (Coliform Count)	-
4.1 Table 1 (Total Colony Count)	-
4.1 Table 1 (Acidity percent, ice cream only)	-
4.1 Table 1 (Milk Fat, ice cream)	-
4.1 Table 1 (Sucrose, all types)	-
4.1 Table 1 (Total Solids)	-
4.1 Table 1 (weight in gram, ice cream)	-
3.1 (Odour and Flavour)	-
3.2 (Texture and Appearance)	-
3.3 (Freedom from Dirt)	-

-
-

135

IS 4447 (1994)

Sodium benzoate, food grade - Specification (First Revision)

5,300.00 View breakup
Hence Complete Testing Charges for the product are : (16 x ` 300) + ` 500 = ` 5,300.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3 Table 1 (Moisture)	-
3.3 Table 1 (Arsenic )	-
3.3 Table 1 (Heavy Metals)	-
3.3 Table 1 (Melting range of benzoic acid)	-
3.3 Table 1 (Purity,expressed as C7H602)	-
3.1 (Description)	-
3.2.1 (Reaction with Ferric Chloride)	-
3.2.2.1 (Test for Sodium - Reaction with uranylzinc acetate)	-
3.2.2.2 (Test for Sodium - Flame test)	-
3.3 Table 1 (Acidity or alkalinity)	-
3.3 Table 1 (Readily carbonizable substancances)	-
3.3 Table 1 (Readily oxidizable substancances)	-
3.3 Table 1 (Chlorinated organic compounds)	-

-
-

136

IS 2046 (1995)

Decorative thermosetting synthetic resinbonded laminated sheets specification (Second Revision)

Rs 2550.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
5.1 (Colour and Pattern)	-
5.2 (Surface Finish)	-
5.3 ,Table 5 (Thickness)	-
5.4 (Appearance )	-
5.2.2 (Sports, dirt and similar surface defects)	-
5.4.7,Fig. 2 (Staightness of Edges)	-
5.4.6 (Length and width of a full size Laminate)	-
5.4.6 (Length and width of a full size Laminate)	-
5.4.7,Fig. 2 (Staightness of Edges)	-
5.2.2 (Broken Corners )	-
7.2 a) (Marking)	-
7.2 b) (Marking)	-
7.2 c) (Marking)	-
7.2 d) (Marking)	-
7.2.1 (Marking)	-
5.5, Tables 7, Sr No.(i) Annex C (Resistance to Surface wear)	-
5.5, Tables 7, Sr No.(ii) Annex D (Resistance to immersin in boiling water)	-
5.5, Tables 7, Sr No.(iii) Annex E (Resistance to Dry heat at 180 °C)	-
5.5, Tables 7, Sr No.(iv) Annex F (Dimensional Stability at deviated Temperature)	-
5.5, Tables 7, Sr No.(v) Annex G (Dimensional Stability at 20°C)	-
5.5, Tables 7, Sr No.(vi) Annex G (Resistance to impact by small diameter ball)	-
5.5, Tables 7, Sr No.(vii) Annex J (Resistance to impact by large diameter balls (self supporting compact laminates))	-
5.5, Tables 7, Sr No.(viii) Annex K (Resistance to cracking (thin laminates))	-
5.5, Tables 7, Sr No.(ix) Annex B & E (Resistance to scratching)	-
5.5, Tables 7, Sr No.(i) Annex C (Resistance to Surface wear)	-

-
Test facilities are not available for the following: 1 Resistance to colour change in xenon arc light, 2) Formability, xiv Resistance to blistering,3) Flexural Modulus, 4) Flexural Strength, 5)Tensile Strength

137

IS 903 (1993)

Specification for Fire Hose Delivery Couplings, Branch Pipe, Nozzles And Nozzle Spanner - Specificaion

Rs 3600/ View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3 (Finish and workmanship)	-
6 (Branch pipe)	-
6.3 (Hydraulic test requirement)	-
7.3 (Hydraulic test requirement)	-
5.3 (Size and Dimension )	-
3 (Finish and workmanship)	-

-
Test facilities are not available for the following: 1 Thread gauges

138

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

Rs. 9200/- Excluding test on joints View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 (Outer Diameter, Thickness & Mass)	-
Cl 14 (Tensile Test, Flattening Test & Bend Test)	-
Cl 15 (Workmanship)	-
7, 6.1.1 (CARBON)	-
7, 6.1.1 (SULPHUR)	-
7, 6.1.1 (PHOSPHURS)	-
7, 6.1.1 (MANGANESE)	-
7, 6.1.1 (SILICON)	-

-
Test facilities are not available for the following: 1. Micro-alloying elements like Nb. V or Ti, Nitrogen, Al,Cu 2. Bending test

139

IS 2002 (2009)

Steel plate for pressure vessel for intermediate and high temperature service including boilers (Third Revision)

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.1 (Carbon %)	-
6.1 (Manganese %)	-
6.1 (Phosphorus %)	-
6.1 (Sulphur %)	-
6.1 (Silicon %)	-
Cl 12 (UTM)	-
Cl 13 (Press)	-
Cl 14 (Workmanship)	-
Cl 9 (Length, Width & Thickness)	-
Cl 12 (UTM)	-
Cl 13 (Press)	-
Cl 14 (Workmanship)	-
Cl 9 (Length, Width & Thickness)	-

-
Test facilities are not available for the following: 1. Al, N, Cu, Mn, Cr, Mo, V, Ni 3. Homogeneity test 3. Ultrasonic test, ( cl 15 )

140

IS 7224 (2006)

Iodized salt, vacuum evaporated iodized salt and refined iodized salt - Specification (Second Revision)

Rs7440/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.2 (Particle Size)	-
Clause 4.3 Table 1 (Moisture content)	-
Clause 4.3 Table 1 (water insoluble matter)	-
Clause 4.3 Table 1 (Calcium (as Ca))	-
Clause 4.3 Table 1 (Magnesium (as mg))	-
Clause 4.3 Table 1 (Sulphate (as SO4 ),)	-
Clause 4.3 Table 1 (Iodine content, a) Manufacturers Level )	-
Clause 4.3 Table 1 (Alkalinity (as Na2CO3),)	-
Clause 4.3 Table 1 (Arsenic(as As))	-
Clause 4.3 Table 1 (Iron(as Fe))	-
Clause 4.3 Table 1 (Chloride Content(as Nacl))	-
Clause 4.3 Table 1 (Matter soluble in water other than sodium chloride)	-
Clause 4.3 Table 1 (Lead as (Pb))	-
4.4 (Anticaking agents (Potassium Ferrocyanide))	-
Clause 4.3 Table 1 (b) Distribution channel including retailer)	-

-
Test facility not available for the following: 1. Pb

141

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

3200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 18 (Weight)	-
Cl 15 (Length, Width & Thickness)	-
Cl 12 (Sudden Load Applied)	-
Cl 11.3 (Press)	-
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650) (Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-
10 (Yield Stress-IS:1608(P1)-22)	-
10 (Elongation on SoA 5.65mm GL)	-

-
Test facilities are not available for the following: 1. Micro-alloying elements, Cu, Al, Nitrogen 2. Y grove Crackability Test in Structural Steel

142

IS 7532 (2018)

Soft soap - Specification (First RevisIon)

Total testing charges-Rs 8915/- (except storage test), View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
CL 5 ( 5.1) (The material shall be homogeneous translucent mass of jelly-like texture, free from putrescent, fishy or objectionable odour. It applies to soft soap with potassium or sodium base or a mixture of these bases. It does not apply to soaps for medicinal purposes. It may or may not be suitably perfumed subject to agreement between the purchaser and the supplier. It shall be free from foreign matter and visible impurities)	-
5.2 (5.2 The material shall quickly form a satisfactory lather while in use and shall show no sign of any deterioration on storage in original sealed containers under normal conditions for a period of 12 months.)	-
5.4 (Soft soap is liable to lose moisture on keeping. The results obtained for unsaponified and unsaponifiable matter, total free alkali and free caustic alkali by the specific methods of analysis shall, therefore, be recalculated in relation to the specified minimum total fatty matter by means of the equation: Recalculated result = Minimum specified total fatty matter content Actualresult× Actual total fatty matter conten)	-
Table-1 (i) IS.no 286 (Total Fatty Matter ( Type 1 ))	-
Table1(ii) IS.no 286 CL12 (Unsaponified and Unsaponified matter (Type 2 ))	-
Table-1 (iii) IS.no 286 CL 14 (Rosin acids percent by mass of total fatty matter ( Type 1))	-
Table-1 (iv) IS.no 286 Annex A (Total free alkali ( as K2O ) type 1)	-
Table-1 (v) IS.no 286 CL 6 ( see note ) (Free Caustic alkali ( as K2O) type 1)	-
5.3 (The soap shall not become liquid at 32°C, and no liquid shall separate when the soap is maintained at 0°C, for 24 h.)	-
Table-1 (ii) IS.no 286 CL 12 (Unsaponified and Unsaponified matter (Type 1 ))	-

-
-

143

IS 14542 (1998)

Partly skimmed milk powder specification

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1(i) (Moisture Type I (IS 11623))	-
Table 1(ii) (Total solids (milk solids and added salts) Type I (IS 11623))	-
Table 1(iii) (Milk fat, Type I (IS I1722))	-
Table 1(iv) (Insolubility index, a) Roller dried Type I (IS 12759))	-
Table 1(v) (Total ash Type I (Annex B of IS 14433 - Part 1))	-
Table 1(vi) (Titratable acidity (as lactic acid) Type I (IS 11766))	-
Cl 6.4 (Flavour and Taste (IS 10030))	-
Cl 6.6.1 (Bacterial Count (IS 5402))	-
Cl 6.6.2 (Coliform Count ((IS 5402))	-

-
-

144

IS 1806 (2018)

Malted milk foods - Specification (Second Revision)

- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
4.3-Table 1- i (Moisture)	-
4.3-Table 1- ii (Total protein (N × 6.25) (on dry basis),)	-
4.3-Table 1- iii (Total fat (on dry basis))	-
4.3-Table 1- iv (Total ash (on dry basis))	-
4.3-Table 1- v (Acid insoluble ash (on dry basis) (in dilute HCl))	-
4.3-Table 1- vi (Solubility)	-
4.3-Table 1- viii (Test for starch)	-
4.3-Table 1- ix (Bacterial count)	-
4.3-Table 1- x (Coliform count)	-
4.3-Table 1- xi (E. coli)	-
4.3-Table 1- xii (Yeast and mould count)	-
4.3-Table 1- xiii (Salmonella)	-
4.3-Table 1- xiv (Shigella)	-
4.3-Table 1- xv (Vibrio cholerae )	-
4.3-Table 1- xv ( V. parahaemolyticus)	-
4.3-Table 1- xvi (Faecal streptococci )	-
4.3-Table 1- xvi ( Staphylococcusaureas)	-

-
-

145

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

Testing charges are Rs.9050/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 8 & 9 (Diameter)	-
6 (Carbon %)	-
6 (Sulphur %)	-
6 (Phosphorus %)	-
6 (Manganese %)	-
6 (Silicon %)	-

-
Test facilities are not available for the following: 1. Cu, V, Ti, Al, Cr, Ni, Mo

146

IS 2785 (1979)

Specification for natural cheese (Hard Variety), processed cheese, processed cheese spread and soft cheese (First Revision)

Rs 3000/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.3.1 (Appearance)	-
3.3.2 (Odour and Flavour)	-
3.3.3 (Texture and Consistency)	-
3.3.4- Table 1-i (Moisture- Annex A)	-
3.3.4- Table 1-ii (Milk fat ( on dry basis)- Annex B)	-
3.3.4- Table 1-iii (Salt ( added sodium chloride)- Annex C)	-

-
-

147

IS 13428 (2024)

PACKAGED NATURAL MINERAL WATER - SPECIFICATION Third Revision

19200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
6.2 Table-1 vi (pH)	-
6.2 Table-1 v (Total dissolved solids)	-
6.2 Table-1 iv (Turbidity)	-
6.2 Table-1 iii (Taste)	-
6.2 Table-1 ii (Odour)	-
6.1.8 (Vibrio parahemolyticus)	-
6.1.8 (Vibrio cholera )	-
6.1.7 (Shigella)	-
6.1.7 (Salmonella )	-
6.1.6 (Yeast and Mould )	-
6.1.5 (Pseudomonas Aeruginosa )	-
6.1.4 (Sulphite Reducing Anaerobes )	-
6.1.3 (Staphylococcus Aureus)	-
6.1.3 (Faecal Streptococci )	-
6.1.2 (Coliform , bacteria)	-
6.1.1 (Escherichia coli(or thermotolerant bacteria))	-
6.2 Table-2 i (Nitrate (as NO3))	-
6.2 Table-2 ii (Nitrite (as NO2))	-
6.2 Table-2 iv (Manganese (as Mn))	-
6.2 Table-2 v (Copper (as Cu))	-
6.2 Table-2 vii (Flouride (as F))	-
6.2 Table-2 viii (Barium (as Ba))	-
6.2 Table-2 ix (Antimony (as Sb))	-
6.2 Table-2 x (Borates (as B))	-
6.2 Table-2 xi (Silver (as Ag))	-
6.2 Table-2 xii (Chloride (as Cl))	-
6.2 Table-2 xiii (Sulphate (as SO4),)	-
6.2 Table-2 xiv (Magnesium (as Mg))	-
6.2 Table-2 xv (Calcium (as Ca))	-
6.2 Table-2 xvi (Sodium (as Na))	-
6.2 Table-2 xvii (Alkalinity (as HCO3))	-
6.2 Table-2 xviii (Selenium (as Se))	-
6.2 Table-3 v (Mercury (as Hg))	-
6.2 Table-3 ii (Cadmium (as Cd))	-
6.2 Table-3 i (Arsenic (as As))	-
6.2 Table-3 vi (Lead (as Pb)	-
6.2 Table-3 iv (Chromium (as Cr))	-
6.2 Table-3 vii (Nickel (as Ni))	-

-
Test facility not available for following: 1. Cyanide 2.RAR

148

IS 5168 (2018)

Glass feeding bottles - Specification (First Revision)

Rs. 6100.00 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Cl 4 (Types)	-
Cl 5.2 (Description)	-
Cl 5.3 (Capacity)	-
Cl 5.5 (Scale and Graduations)	-
Cl 5.7 (Thermal Shock Resistance)	-
5.8 (Migration of Heavy and toxic Elements)	-

-
-

149

IS 4947 (2006)

Foam concentrate for producing mechanical foam for fire fighting - Specification (Fourth Revision)

Please see remarks. View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Clause 4.1 (A) (Carbon)	-
Clause 4.1 (A) (Silicon)	-
Clause 4.1 (A) (Sulphor )	-
Clause 4.1 (A) (Phosphorous)	-
Clause 4.1 (A) (Manganese)	-
Cl 3 (General Requirements)	-
Cl 6 (Capacity and Contents)	-
Cl 5 (Construction)	-
Cl 7 (Performance Requirements )	-
Cl 7.3 (Leakage Test)	-
Cl 8 (Finish)	-

-
Test facilities are not available for the following: (1) Pitch and included angle

150

IS 13334 : Part 2 (2014)

Skimmed milk powder - Specification: Part 2 extra grade (First Revision)

Rs 10430/- View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
Table 1 (i) (Moisture (IS 116231or 16072))	-
Table 1 (ii) (Milk protein in milk solids not fat (IS 72192))	-
Table 1 (iii) (Milk fat (IS 117213) or Annex B)	-
Table 1 (iv) (Insolubility index (IS 12759))	-
Table 1 (v) (Total ash (on dry basis), Annex B of IS 14433)	-
Table 1 (vi) (Titratable acidity (IS 11766))	-
Table 1 (ix) (Bacterial count (IS 5402))	-
Table 1 (x) (Coliform count (IS 5401 - Part 1))	-
Table 1 (xi) (Escherichia coli (IS 5887 - Part 1))	-
Table 1 (xii) (Coagulase positive Staphylococcus aureus (IS 5887 - Part 2))	-
Table 1 (xiii) (Salmonella (IS 5887 - Part 3))	-
Table 1 (xiv)(a) (Spore Count: a)Aerobic (Bacillus cereus) Type m (IS 5887 - Part 6))	-
Table 1 (xiv)(b) (Spore Count: b) Anaerobic (Sulfite reducing Clostridia) Type m (ISO 15213 : 2003))	-
Table 1 (xv) (Listeria monocytogenes (IS 14988 - Part 2 : 2001))	-
Table 1 (viii) (Scorched particles (equivalent to Disc B) (IS 13500))	-

-
Test facility not available for the following: (1) As per Cl. 5.7 The pesticide residues, heavy metals, toxins (aflatoxins and other naturally occurring toxins) and contaminants, if any, in the product shall not exceed the limits as prescribed in the Food Safety and Standards (Contaminants, Toxins and Residues) Regulations, 2011.’

First
Prev
4
5
6
7
Next
Last

Bureau of Indian Standards

The National Standards Body of India

BIS, Western Regional Laboratory (WRL)

BUREAU OF INDIAN STANDARDS (WESTERN REGIONAL LABORATORY), PLOT NO. E9, ROAD NO. 8, M.I.D.C, ANDHERI (EAST), MUMBAI, MAHARASHTRA, INDIA, MUMBAI, Mumbai Suburban, Maharashtra, 400093

- wrol@bis.gov.in

Scope List