BIS - LIMS (Laboratory Information Management System)

Conformity Testing Labs Pvt. Ltd. Unit 2

A-33, Mayapuri Industrial Area, Phase 1, New Delhi, New Delhi, New Delhi, Delhi, 110064

7840889997 qa@labctl.in

Scope List

Reset

106 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 302 : Part 1 (2024)

Household and Similar Electrical Appliances â Safety Part 1 General Requirements (Seventh Revision)

275000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
12(Charging of metal-ion batteries)	-	20000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
19.11.4.6(Class 3 Voltage dips and interruptions)	-	15000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
19.11.4.4(Surge immunity test)	-	15000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
19.11.4.3(Fast transient bursts)	-	15000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
19.11.4.1(Electrostatic discharges)	-	15000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.8(Temperature rise)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.7(Duration corresponding)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.6(Combined appliances)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.5(Motor-operated appliances)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.4(Heating appliances)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
8.1.5(Live parts of built-in appliances)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
17(Overload protection of transformers and associated circuits)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
16(Leakage current and electric strength)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
31(Resistance to Rusting)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
30.2(Needle Flame Test)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
30.2(Glow Wire Test)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
30.1(Ball pressure test)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
29(clearance, creepage distances and solid insulation)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
28(Screw test and connections)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
27(Provision for earthing)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
26(Terminals for external conductors)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
25(Supply connection and external flexible cords)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
24(Components)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
23(Internal wiring)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
22(Construction)	-	85000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
20(Stability and mechanical hazards)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
19(Abnormal Operation)	-	10000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
17(Over Load Protection of Transformers and associated circuits)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
16.3(Electric Strength (after clause 15 and 16.2))	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
16.2(Leakage Current (after Clause 15))	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
16.1(General)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
15.3(Humidity Test)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
15.2(Spillage Test)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
15.1(Ingress Protection test other than IPX0 (IP test))	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
15.0(Moisture resistance)	-	7000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
14(Transient Over Voltages)	-	7000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
13.3(Electric Strength at operating temperature)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
13.2(Leakage current at operating temperature)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
13(Leakage current and electric strength at operating temperature)	-	10000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.3(Heating)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.2(General)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
11.1(General)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
10.2(Current input)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
10.1(Power input)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
8.1.4(Protection against live parts against protective impedance)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
8.1.3(Protection against live parts in visible glowing heating elements)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
8.1.2(Protection against live parts in openings)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
8.1.1(Protection against live parts in all positions)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
7(Marking and instructions)	-	3000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
Annex C(Ageing test on motors)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
15.2(Moisture resistance)	-	10000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
19.17(Abnormal operation)	-	10000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
20.1(Stability and mechanical hazards)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
21.2(Mechanical strength)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
21.3(Mechanical strength)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
21(Mechanical Strength)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
22.5(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
22.6(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
22.11(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
22.16(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
22.32(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
22.42(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
23.3(Internal wiring)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
25(Supply connection and external flexible cords)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
25.7(Supply connection and external flexible cords)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
25.14(Supply connection and external flexible cords)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
25.15(Supply connection and external flexible cords)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
26.5(Terminals for external conductors)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
27.5(Provision for earthing)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
28.1(Screws and connections)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
B.22.1(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
B.22.3(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
B.22.4(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
B.22.5(Construction)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
18(Endurance)	-	50000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
6(Classification)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
5(General conditions for the tests)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
4(General requirement)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
9(Starting of motor operation test requirements and tests)	-	10000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
Annex D(Thermal motor protectors)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
32(Radiation Toxicity and Similar Hazards)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
A.2(Earth continuity test)	-	15000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
18(Endurance)	-	50000	Reduced Charges may apply for non complex Product depending upon parameters not applicable
16.0(General)	-	5000	Reduced Charges may apply for non complex Product depending upon parameters not applicable

05 Apr, 2027

-
-

IS 18112 (2022)

Digital Television Receiver for Satellite Broadcast Transmission Specification

164000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
3.6(Electromagnetic Compatibility (EMC) Requirements)	-	164000		-
3.5(Safety specification)	-	0		-

05 Apr, 2027

-
Included w.e.f 25.03.2025. Only for Cl 3.6 (Electromagnetic Compatibility (EMC) Requirements):- Conducted Emmision (Table A.8 to A.12) & Cl.3.5 (Safety Requirements)

IS 302 : Part 2 : Sec 203 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 203 electric call bells and buzzers for indoor use

21500 View breakup
-

Clause No.	Exclusion	Remark
5(Rating)	-	-
6(Classification)	-	-
7(Marking)	-	-
8(Protection against Access to Live Parts)	-	-
9(Starting Of Motor Operated Appliances)	-	-
10("Power Input & Current")	-	-
11(Temperature Rise/ Heating)	-	-
12(Operation Under Overload Conditions of Appliances with heating Element)	-	-
13(Leakage Current and Electric Strength at Operating Temperature)	-	-
14("Radio and Television Interference Suppression / Transient Over Voltage ")	-	-
15(Moisture Resistance)	-	-
16(Leakage Current and Electric Strength/ Insulation Resistance and Electric Strength (After Humidity treatment))	-	-
17(Overload Protection/ Overload Protection of Transformers & Associated Circuits)	-	-
18(Endurance)	-	-
19(Abnormal Operation)	-	-
20(Stability & Mechanical Hazards)	-	-
21(Mechanical strength)	-	-
22(Construction)	-	-
23(Internal Wiring)	-	-
25(Supply Connection & External Flexible Cords)	-	-
26(Terminals For External Conductors)	-	-
27(Provision For Earthing)	-	-
28(Screws & Connections)	-	-
29(Clearances, Creepage Distances & Solid Insulation)	-	-
30(Resistance to Heat & Fire)	-	-
31(Resistance to Rusting)	-	-
32(Radiation hazards)	-	-
Cl 19.11.4.1(Electrostatic discharges)	-	-
Cl 19.11.4.3(Fast transient bursts)	-	-
Cl 19.11.4.4(Surge immunity test)	-	-
Cl 19.11.4.6(Class 3 Voltage dips and interruptions)	-	-

05 Apr, 2027

-
Included w.e.f 20.06.2025

IS/IEC 61683 (1999)

Photovoltaic systems - Power conditioners - Procedure for measuring efficiency

110000 View breakup
-

Clause No.	Exclusion	Remark
5(Efficiency calculations)	-	-
6(Efficiency test circuits)	-	-
7(Loss measurement)	-	-
Annex A(Power conditioner description)	-	-
Annex B(Power efficiency and conversion factor)	-	-
Annex C(Weighted average energy efficiency)	-	-
Annex D(Derivation of efficiency tolerance in Table 2)	-	-
4(Efficiency measurement conditions)	-	-
4.1(DC power source for testing)	-	-
4.2(Temperature)	-	-
4.3(Output voltage and frequency)	-	-
4.4(Input voltage)	-	-
4.5(Ripple and distortion)	-	-
4.6(Resistive loads/utility grid)	-	-
4.7(Reactive loads)	-	-
4.8(Resistive plus non-linear loads)	-	-
4.9(Complex loads)	-	-
5(Efficiency calculations)	-	-
6(Efficiency test circuits)	-	-
7(Loss measurement)	-	-
Annex A(Power conditioner description)	-	-
Annex B(Power efficiency and conversion factor)	-	-
Annex C(Weighted average energy efficiency)	-	-
Annex D(Derivation of efficiency tolerance in Table 2)	-	-
4(Efficiency measurement conditions)	-	-
4.1(DC power source for testing)	-	-
4.2(Temperature)	-	-
4.3(Output voltage and frequency)	-	-
4.4(Input voltage)	-	-
4.5(Ripple and distortion)	-	-
4.6(Resistive loads/utility grid)	-	-
4.7(Reactive loads)	-	-
4.8(Resistive plus non-linear loads)	-	-
4.9(Complex loads)	-	-
5(Efficiency calculations)	-	-
6(Efficiency test circuits)	-	-
7(Loss measurement)	-	-
Annex A(Power conditioner description)	-	-
Annex B(Power efficiency and conversion factor)	-	-
Annex C(Weighted average energy efficiency)	-	-
Annex D(Derivation of efficiency tolerance in Table 2)	-	-
4(Efficiency measurement conditions)	-	-
4.1(DC power source for testing)	-	-
4.2(Temperature)	-	-
4.3(Output voltage and frequency)	-	-
4.4(Input voltage)	-	-
4.5(Ripple and distortion)	-	-
4.6(Resistive loads/utility grid)	-	-
4.7(Reactive loads)	-	-
4.8(Resistive plus non-linear loads)	-	-
4.9(Complex loads)	-	-

05 Apr, 2027

-
Included w.e.f.18.06.2025

IS 17980 (2022)

Maximum Power Point Tracking Efficiency of Grid Connected Photovoltaic Inverters (First Revision)

490000 View breakup
-

Clause No.	Exclusion	Remark
Cl-4.1 (a)(Static MPPT efficiency)	-	-
Cl-4.1 (b)(Dynamic MPPT efficiency)	-	-
Cl-4.1 (a)(Static MPPT efficiency)	-	-
Cl-4.1 (b)(Dynamic MPPT efficiency)	-	-

05 Apr, 2027

-
Included w.e.f.18.06.2025

IS 302 : Part 2 : Sec 11 (1994)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 11 tumbler dryers

180000 View breakup
-

Clause No.	Exclusion	Remark
3(GENERAL REQUIREMENT)	-	-
4(GENERAL NOTES ON TESTS)	-	-
5(RATING)	-	-
6(CLASSIFICATION)	-	-
7(MARKING)	-	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	-
10(INPUT AND CURRENT)	-	-
11(HEATING)	-	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	-
15(MOISTURE RESISTANCE)	-	-
17(OVERLOAD PROTECTION)	-	-
18(ENDURANCE )	-	-
19(ABNORMAL OPERATION)	-	-
20(STABILITY AND MECHANICAL HAZARDS)	-	-
21(MECHANICAL STRENGTH)	-	-
22(CONSTRUCTION)	-	-
23(INTERNAL WIRING)	-	-
24(COMPONENTS)	-	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	-
27(PROVISION FOR EARTHING)	-	-
28(SCREWS AND CONNECTIONS)	-	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	-
31(RESISTANCE TO RUSTING)	-	-
32(RADIATION, TOXICITY AND SIMILAR HAZARDS)	-	-
12(OPERATION TJNDER OVERLOAD CONDITIONS OF APPLIANCES WITH HEATING ELEMENTS)	-	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH)	-	-
30(RESISTANCE TO HEAT, FIRE AND TACKING)	-	-
101.1(Type Tests)	-	-
101.2(Acceptance Tests)	-	-
101.3(Routine Tests)	-	-

05 Apr, 2027

-
Included w.e.f.21.05.2025 Exclusion 19 (ABNORMAL OPERATION) Radiated emission, Conducted & Radiated susceptibility

IS 4250 (2025)

Electric Food-Mixers (Liquidizers and Grinders) and Centrifugal Juicers ï¿½ Specification ( Second Revision )

39000 View breakup
-

Clause No.	Exclusion	Remark
Cl-4(General Requirements)	-	-
Cl-5(General Conditions for the tests)	-	-
Cl-6(Classification)	-	-
Cl-7(Marking)	-	-
Cl-8(Safety Requirements)	-	-
Cl-9(Endurance fpr motor and base assembly)	-	-
Cl-10.2("Grinding Coffee (for Machines that Have a Dry Grinding Arrangement)")	-	-
Cl-10.3(Whisking Egg Whites (for Machines that have Whisking Egg Arrangement))	-	-
Cl-10.4(Idli Batter)	-	-
Cl-10.5(Operational Tests for Juicers)	-	-
Cl-11(Temperature Withstand Test for Bowl)	-	-
Cl-12.1(Test for Switches)	-	-
Cl-13(Strength of Assembly)	-	-
Cl-14.2, 14.3 Table-2 (i)(Protection against access to live parts)	-	-
Cl-14.2, Table-2 (ii)(Power input and current)	-	-
Cl-14.2, 14.3 Table-2 (iii)(Leakage current and electric strength at operating temperature)	-	-
Cl-14.2, Table-2 (iv)(Moisture resistance)	-	-
Cl-14.2, Table-2 (v)(Leakage current and electric strength)	-	-
Cl-14.2, 14.3 Table-2 (vi)(Provision for earthing)	-	-
Cl-19.11.4.1(Electrostatic discharges)	-	-
Cl-19.11.4.3(Fast transient bursts)	-	-
Cl-19.11.4.4(Surge immunity test)	-	-

05 Apr, 2027

-
Included w.e.f 07.05.2025 Exclusion: Cl-19.11.4.2 (Radiated fields), Cl-19.11.4.5 (Immunity to conducted discharges), Cl-19.11.4.6 (Class 3 Voltage dips and interruptions), Cl-19.11.4.7 (Harmonics)

IS 302 : Part 2 : Sec 8 (2024)

Household and Similar Electrical Appliances âSafety Part 2 Particular Requirements Section 8 Shavers, Hair Clippers and Similar Appliances (First Revision)

70000 View breakup
-

Clause No.	Exclusion	Remark
7(Marking and instructions)	-	-
8(Protection against access to live parts)	-	-
10(Power input and current)	-	-
11(Heating)	-	-
12(Charging of metal-ion batteries)	-	-
13.1 &13.2(Leakage current test)	-	-
13.1 &13.3(Electric strength test)	-	-
14(Transient overvoltages)	-	-
15(Moisture resistance)	-	-
15.3(Moisture resistance)	-	-
16.1 &16.2(Leakage current test)	-	-
16.1 & 16.3(Electric strength test)	-	-
17(Overload protection of transformers and associated circuits)	-	-
19.1 to 19.13, Table No. - 9(Abnormal operation)	-	-
19.101(Abnormal operation)	-	-
20.1(Stability and mechanical hazards)	-	-
20.2(Stability and mechanical hazards)	-	-
21(Mechanical strength)	-	-
21.101(Mechanical strength)	-	-
21.102(Mechanical strength)	-	-
21.103(Mechanical strength)	-	-
22(Construction)	-	-
22.101(Construction)	-	-
22.102(Construction)	-	-
22.103(Construction)	-	-
23(Internal wiring)	-	-
24(Components)	-	-
25("Supply connection and external flexible cords")	-	-
26("Terminals for external conductors")	-	-
27(Provision for earthing)	-	-
28(Screws and connections)	-	-
29("Clearances, creepage distances and solid insulation")	-	-
30(Resistance to heat and fire)	-	-
31(Resistance to rusting)	-	-
32("Radiation, toxicity and similar hazards")	-	-
19.11.4.1(Electrostatic discharges)	-	-
19.11.4.3(Fast transient bursts)	-	-
19.11.4.4(Surge immunity test)	-	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	-

05 Apr, 2027

-
Included w.e.f 07.05.2025 Exclusion : Cl 19.11.4.2 (Radiated fields), Cl 19.11.4.5 (Immunity to conducted discharges), Cl 19.11.4.7 (Harmonics), Cl 24 (Components)

IS 302 : Part 2 : Sec 4 (1993)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 4 spin extractors

180000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(GENERAL REQUIREMENTS)	-	5000	-
4(GENERAL NOTES ON TESTS)	-	5000	-
5(RATING)	-	5000	-
6(CLASSIFICATION)	-	5000	-
7(MARKING)	-	5000	-
8(PROTECTION AGAINST ELECTRIC SHOCK)	-	5000	-
9(STARTING OF MOTOR-OPERATED APPLIANCES)	-	5000	-
10(INPUT AND CURRENT)	-	5000	-
11(HEATING)	-	5000	-
13(ELECTRICAL INSULATION AND LEAKAGE CURRENT AT OPERATING TEMPERATURE)	-	10000	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	10000	-
15(MOISTURE RESISTANCE)	-	25000	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH (AFTER HUMIDITY TREATMENT))	-	5000	-
17(OVERLOAD PROTECTION)	-	5000	-
19(ABNORMAL OPERATION)	-	5000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	5000	-
21(MECHANICAL STRENGTH)	-	25000	-
22(CONSTRUCTION)	-	10000	-
23(INTERNAL WIRING)	-	5000	-
24(COMPONENTS)	-	5000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	5000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	5000	-
27(PROVISION FOR EARTHING)	-	5000	-
28(SCREWS AND CONNECTIONS)	-	5000	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	5000	-
30(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	40000	-
31(RESISTANCE TO RUSTING)	-	5000	-
19.11.4.1(Electrostatic discharges)	-	15000	-
19.11.4.3(Fast transient bursts)	-	15000	-
19.11.4.4(Surge immunity test)	-	10000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	10000	-

05 Apr, 2027

-
Included w.e.f 07.05.2025 Exclusion: Cl 19.11.4.2 (Radiated fields), Cl 19.11.4.5 (Immunity to conducted discharges), Cl 19.11.4.7 (Harmonics), Cl 24 (COMPONENTS)

IS 16169 (2019)

Utility - Interconnected photovoltaic inverters - Test procedure of islanding prevention measures (First Revision)

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6(Test for single or multi-phase inverter)	-	50000	-
Annex A(Islanding as it applies to PV systems)	-	20000	-
Annex B(Test for independent islanding device)	-	10000	-
6 to 6.2(Test for single or multi-phase inverter to Pass/fail criteria)	-	130000	-
7(Documentation)	-	20000	-
4(Testing circuit)	-	30000	-
5(Testing equipment)	-	20000	-
Annex C(Gate blocking signal)	-	10000	-

05 Apr, 2027

-
Included w.e.f.30.04.2025

IS 302 : Part 2 : Sec 2 (1997)

Safety of household and similar electrical appliances: Part 2 particular requirements: Sec 2 vacuum cleaners and water suction cleaning appliances

155000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Rating)	-	5000	-
6(Classification)	-	5000	-
7(Marking)	-	5000	-
8(Protection against Access to Live Parts)	-	5000	-
9(Starting Of Motor Operated Appliances)	-	5000	-
10("Power Input & Current")	-	5000	-
11(Temperature Rise/ Heating)	-	5000	-
12(OPERATION UNDER OVERLOAD CONDITIONS OF APPLIANCES WITH HEATING ELEMENTS)	-	5000	-
17(OVERLOAD PROTECTION)	-	5000	-
14(RADIO AND TELEVISION INTERFERENCE SUPPRESSION)	-	0	-
15(MOISTURE RESISTANCE)	-	25000	-
16(INSULATION RESISTANCE AND ELECTRIC STRENGTH ( AFTER HUMIDITY TREATMENT ))	-	5000	-
19(ABNORMAL OPERATION)	-	5000	-
20(STABILITY AND MECHANICAL HAZARDS)	-	5000	-
21(MECHANICAL STRENGTH)	-	20000	-
22(Construction)	-	5000	-
23(INTERNAL WIRING)	-	5000	-
29(CREEPAGE DISTANCES, CLEARANCES AND DISTANCES THROUGH INSULATION)	-	5000	-
25(SUPPLY CONNECTION AND EXTERNAL FLEXIBLE CABLES AND CORDS)	-	5000	-
26(TERMINALS FOR EXTERNAL CONDUCTORS)	-	5000	-
32(RADIATION HAZARDS)	-	5000	-
28(SCREWS AND CONNECTIONS)	-	5000	-
30(RESISTANCE TO HEAT, FIRE AND TRACKING)	-	30000	-
31(RESISTANCE TO RUSTING)	-	5000	-
19.11.4.6(Class 3 Voltage dips and interruptions)	-	10000	-
19.11.4.4(Surge immunity test)	-	10000	-
19.11.4.3(Fast transient bursts)	-	10000	-
19.11.4.1(Electrostatic discharges)	-	10000	-
13(LEAKAGE CURRENT AND ELECTRIC STRENGTH AT OPERATING TEMPERATURE)	-	5000	-
27(PROVISION FOR EARTHING)	-	5000	-

05 Apr, 2027

-
Included w.e.f.29.04.2025 Exclusion Cl 19.11.4.2 (Radiated fields) Cl 19.11.4.5 (Immunity to conducted discharges) Cl 19.11.4.7 (Harmonics) Cl 24 (COMPONENTS)

IS/IEC 60529 (2001)

Degrees of protection provided by enclosures (IP Code)

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5(Degrees of protection against access to hazardous parts and against solid foreign objects indicated by the first characteristic numeral)	-	11000	Rs. 11000 per IP Numeral
Cl-5.1(Protection against access to hazardous parts)	-	11000	Rs. 11000 per IP Numeral
Cl-5.2(Protection against solid foreign objects)	-	11000	Rs. 11000 per IP Numeral
Cl-6(Degrees of protectlon against ingress of water indicated 'by the second characteristic numeral)	-	11000	Rs. 11000 per IP Numeral
Cl-7(Degrees of protection against access to hazardous parts indicated by the additional letter)	-	11000	Rs. 11000 per IP Numeral
Cl-8(Supplementary letter)	-	11000	Rs. 11000 per IP Numeral
Cl-10(Marking)	-	11000	Rs. 11000 per IP Numeral

05 Apr, 2027

-
Included w.e.f.09.04.2025

IS 17625 : Part 2 : Sec 69 (2021)

Medical Electrical Equipment Part 2 Particular Requirements for Basic Safety and Essential Performance Section 69 Oxygen Concentrator Equipment

950000 View breakup
-

Clause No.	Exclusion	Remark
201.4(Power and Current)	-	-
201.5(Temperature, Humidity, Dimensions, Force)	-	-
201.7.1.2(Legibility of markings)	-	-
201.8(Current, Voltage, Energy, Dimensions, Impedance)	-	-
201.9(Mechanical dimensions, strength , torque, force)	-	-
201.9.6.2.1.101(Additional requirements for audible acoustic energy)	-	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	-
201.11.1(Maximum temperature during NORMAL USE)	-	-
"201.11. 1.2.2"(APPLIED PARTS not intended to supply heat to a PATIENT)	-	-
201.11.2.101(Additional requirements for fire prevention)	-	-
201.11.6.7(Leakage currents , dielectirc strength)	-	-
"201.11. 8.101"()	-	-
201.11.8.101.1(TECHNICAL ALARM CONDITION for power supply failure)	-	-
201.11.8.101.2(INTERNAL ELECTRICAL POWER SOURCE)	-	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	-
"201.12. 1"(Legibility of markings)	-	-
201.12.1.101(Flowrate control)	-	-
201.12.1.103(Accuracy of concentration)	-	-
201.12.1.104(Outlet pressure)	-	-
201.12.4.4.101.2(Indication of start-up period)	-	-
201.12.4.102(Low oxygen concentration ALARM CONDITION)	-	-
201.13(HAZARDOUS SITUATIONS and fault conditions)	-	-
201.13.2.101(Additional specific SINGLE FAULT CONDITIONS)	-	-
201.15(Mechanical strength, Temperature, current)	-	-
201.16(Leakage currents , dielectirc strength)	-	-
201.17(Electromagnetic compatibility)	-	-
201.102.3(Fire RISK reduction in ACCESSORIES)	-	-
202(Electromagnetic disturbances - Requirements and tests)	-	-
211(Temperature, humidity, altitude, IP, Vibration, Mechanical shock)	-	-
201.7(ME equipment identification, marking and documents)	-	-
201.10(Protection against unwanted and excessive radiaton hazards)	-	-
201.12.4.103(Filter for the delivered gas)	-	-
201.12.4.4.101.1(Flowrate control)	-	-
201.12.1.102(Accuracy of triggered flow)	-	-
201.11.7(Biocompatibility of ME equipment and ME systems)	-	-
12.11.6.6(Cleaning and disinfection of ME equipment or ME system)	-	-
201.11.3.101(Additional requirements for fire enclosures of ME equipment)	-	-
201.6(Classification of ME equipment and ME systems)	-	-
201.6(General requirements)	-	-
201.5(General requirements for testing of ME equipment)	-	-
201.4(General requirements)	-	-
201.7(ME equipment identification, marking and documents)	-	-
201.8(Protection against electrical hazards from ME equipment)	-	-
201.9(Protection against mechanical hazards of ME equipment and ME systems)	-	-
201.1(Protection against unwanted and excessive radiation hazards)	-	-
201.11(Protection against excessive temperatures and other hazards)	-	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	-
201.13(Hazardous situations and fault conditions for ME equipment)	-	-
201.14(Programmable electrical medical systems (PEMS))	-	-
201.14(Programmable electrical medical systems (PEMS))	-	-
201.16(ME systems)	-	-
201.17(Electromagnetic compatibility of ME equipment and ME systems)	-	-
201.101(Outlet connector)	-	-
201.102(Requirements for parts and accessories)	-	-
201.103(Functional connection)	-	-
201.104(Indication of duration of operation)	-	-
201.105(Integrated conserving equipment function)	-	-
202(Electromagnetic disturbances – Requirements and tests)	-	-
211(Requirements for medical electrical equipment and medical electrical systems used in the home healthcare environment)	-	-

05 Apr, 2027

-
Included w.e.f 25.03.2025 Exclusion: Cl 201.17 (Electromagnetic compatibility)(Radiated emission, Conducted & Radiated susceptibility), Cl 202 (Electromagnetic disturbances - Requirements and tests)(Radiated emission, Conducted & Radiated susceptibility)

IS 13450 : Part 2 : Sec 50 (2022)

Medical electrical equipment Part 2 Particular requirements for the Basic Safety and essential performance Section 50 Infant Phototherapy Equipment

900000 View breakup
-

Clause No.	Exclusion	Remark
201.4(General requirements)	-	-
201.5(General requirements for testing ME EQUIPMENT)	-	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	-
201.7(ME EQUIPMENT identification, marking and document)	-	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	-
201.9(Protection against MECHANICAL HAZARDS of ME EQUIPMENT and ME SYSTEMS)	-	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	-
201.15(Construction of ME EQUIPMENT)	-	-
201.16(ME SYSTEMS)	-	-
201.17(Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)	-	-
202(Electromagnetic disturbances – Requirements and tests)	-	-

05 Apr, 2027

-
Included w.e.f 25.03.2025 Exclusion: Cl 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)(Radiated emission, Conducted & Radiated susceptibility), Cl 202 (Electromagnetic disturbances – Requirements and tests)(Radiated emission, Conducted & Radiated susceptibility)

IS 2993 : Part 2 (2024)

a.c. Motor Capacitors Part 2 Motor Start Capacitors ( Third Revision )

375000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.7(Voltage test between the terminals)	-	5000	-
5.1.8(Voltage test between terminals and case)	-	5000	-
5.1.9(Capacitance measurement)	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.11.1(Robustness of terminations)	-	5000	-
5.1.11.2(Soldering)	-	5000	-
5.1.11.3(Vibration)	-	5000	-
5.1.12(Sealing test)	-	5000	-
5.1.13(Endurance test)	-	120000	-
5.1.14(Damp heat test)	-	120000	-
5.1.15(Self-healing test)	-	20000	-
5.1.16(Destruction test)	-	30000	-
5.1.17.1(Ball-pressure test)	-	20000	-
5.1.17.2(Glow-wire test)	-	5000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	5000	-
5.3.2(Terminals and connecting cables)	-	5000	-
5.3.3(Earth connections)	-	5000	-
5.3.4(Discharge devices)	-	5000	-
5.3.5(Pollution)	-	5000	-
5.4(Marking)	-	5000	-
6.1.6(Voltage test between the terminals)	-	5000	-
6.1.7(Voltage test between terminals and case)	-	5000	-
6.1.8(Capacitance and power factor measurement)	-	5000	-
6.1.9(Check of dimensions)	-	5000	-
6.1.10.1(Robustness of terminations)	-	5000	-
6.1.10.2(Soldering)	-	5000	-
6.1.10.3(Vibration)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
6.1.10.5(Rapid change of temperature)	-	5000	-
6.1.11(Sealing test)	-	5000	-
6.1.12(Endurance test)	-	120000	-
6.1.13(Damp heat test)	-	120000	-
6.1.14(Pressure relief test)	-	5000	-
6.3.1(Creepage distances and clearances)	-	5000	-
6.4(Marking)	-	5000	-
7.2.1(Measurement of working voltage)	-	5000	-
7.2.2(Influence of capacitance)	-	5000	-
7.3(Checking capacitor temperature)	-	5000	-
7.4(Checking transients)	-	5000	-
7.5(Storage of electrolytic capacitors)	-	5000	-
Annex A(Test voltage)	-	5000	-
5.1.1.1(General)	-	5000	-
5.3.1(Creepage distances and clearances)	-	5000	-
6.1.15.1(Ball-pressure test)	-	20000	-
6.1.15.2(Glow-wire test)	-	25000	-
6.1.15.3(Tracking test)	-	5000	-
6.2(Overloads)	-	5000	-
6.3.2(Terminals and connecting cables)	-	5000	-
6.3.3(Earth connections)	-	5000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.7(Voltage test between the terminals)	-	5000	-
5.1.8(Voltage test between terminals and case)	-	5000	-
5.1.9(Capacitance measurement)	-	5000	-
5.1.10(Check of dimensions)	-	5000	-
5.1.11.1(Robustness of terminations)	-	5000	-
5.1.11.2(Soldering)	-	5000	-
5.1.11.3(Vibration)	-	5000	-
5.1.12(Sealing test)	-	5000	-
5.1.13(Endurance test)	-	100000	-
5.1.14(Damp heat test)	-	120000	-
5.1.15(Self-healing test)	-	20000	-
5.1.16(Destruction test)	-	30000	-
5.1.17.1(Ball-pressure test)	-	20000	-
5.1.17.2(Glow-wire test)	-	5000	-
5.1.17.3(Tracking test)	-	5000	-
5.2(Overloads)	-	5000	-
5.3.2(Terminals and connecting cables)	-	5000	-
5.3.3(Earth connections)	-	5000	-
5.3.4(Discharge devices)	-	5000	-
5.3.5(Pollution)	-	5000	-
5.4(Marking)	-	5000	-
6.1.6(Voltage test between the terminals)	-	5000	-
6.1.7(Voltage test between terminals and case)	-	5000	-
6.1.8(Capacitance and power factor measurement)	-	5000	-
6.1.9(Check of dimensions)	-	5000	-
6.1.10.1(Robustness of terminations)	-	5000	-
6.1.10.2(Soldering)	-	5000	-
6.1.10.3(Vibration)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
6.1.10.5(Rapid change of temperature)	-	5000	-
6.1.11(Sealing test)	-	5000	-
6.1.12(Endurance test)	-	100000	-
6.1.13(Damp heat test)	-	120000	-
6.1.14(Pressure relief test)	-	5000	-
6.3.1(Creepage distances and clearances)	-	5000	-
6.4(Marking)	-	5000	-
7.2.1(Measurement of working voltage)	-	5000	-
7.2.2(Influence of capacitance)	-	5000	-
7.3(Checking capacitor temperature)	-	5000	-
7.4(Checking transients)	-	5000	-
7.5(Storage of electrolytic capacitors)	-	5000	-
Annex A(Test voltage)	-	5000	-
5.1.1.1(General)	-	5000	-
5.3.1(Creepage distances and clearances)	-	5000	-
6.1.15.1(Ball-pressure test)	-	20000	-
6.1.15.2(Glow-wire test)	-	5000	-
6.1.15.3(Tracking test)	-	5000	-
6.2(Overloads)	-	5000	-
6.3.2(Terminals and connecting cables)	-	5000	-
6.3.3(Earth connections)	-	5000	-
6.3.4(Discharge devices)	-	5000	-
6.3.5(Pollution)	-	5000	-
6.1.10.4(Fixing bolt or stud (if fitted))	-	5000	-
5.1.10(Check of dimensions)	-	5000	-

05 Apr, 2027

-
Included w.e.f 25.03.2025

IS 13450 : Part 2 : Sec 37 (2019)

Medical electrical equipment: Part 2 particular requirements for the basic safety and essential performance: Sec 37 ultrasonic medical diagnostic and monitoring equipment

950000 View breakup
-

Clause No.	Exclusion	Remark
201.4(General requirements)	-	-
201.5(General requirements for testing ME EQUIPMENT)	-	-
201.6(Classification of ME EQUIPMENT and ME SYSTEMS)	-	-
201.7(ME EQUIPMENT identification, marking and documents)	-	-
201.8(Protection against electrical HAZARDS from ME EQUIPMENT)	-	-
201.9(Protection against MECHANICAL HAZARDS OF ME EQUIPMENT and ME SYSTEMS)	-	-
201.1(Protection against unwanted and excessive radiation HAZARDS)	-	-
201.11(Protection against excessive temperatures and other HAZARDS)	-	-
201.12(Accuracy of controls and instruments and protection against hazardous outputs)	-	-
201.13(HAZARDOUS SITUATIONS and fault conditions for ME EQUIPMENT)	-	-
201.14(PROGRAMMABLE ELECTRICAL MEDICAL SYSTEMS (PEMS))	-	-
201.15(Construction of ME EQUIPMENT)	-	-
201.16(ME SYSTEMS)	-	-
201.17(ELECTROMAGNETIC COMPATIBILITY of ME EQUIPMENT and ME SYSTEMS)	-	-
202.6(ELECTROMAGNETIC COMPATIBILITY – Requirements and test)	-	-

05 Apr, 2027

-
Included w.e.f 25.03.2025 Exclusion: Cl 201.17 (Electromagnetic compatibility of ME EQUIPMENT and ME SYSTEMS)(Radiated emission, Conducted & Radiated susceptibility), Cl 202.6 (Electromagnetic disturbances – Requirements and tests)(Radiated emission, Conducted & Radiated susceptibility)

IS 2993 : Part 1 (2024)

a.c. Motor Capacitors Part 1 General - Performance, Testing and Rating - Safety Requirements - Guidance for Installation and Operation ( Third Revision )

425000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(General)	-	0	-
5.5(Tangent of loss angle)	-	2000	-
5.7("Voltage test between terminals ")	-	10000	-
5.8(Voltage test between terminals and case)	-	5000	-
5.9(Capacitance measurement)	-	10000	-
5.1(Check of dimensions)	-	5000	-
5.11(Mechanical tests)	-	5000	-
5.12(Sealing test)	-	10000	-
5.13(Endurance test)	-	100000	-
5.14(Damp heat test)	-	110000	-
5.15(Self-healing test)	-	20000	-
5.16(Destruction test)	-	25000	-
5.17(Resistance to heat, fire and tracking)	-	20000	-
5.17.1(Ball-pressure test)	-	2000	-
5.17.2(Glow-wire test)	-	5000	-
5.17.3(Tracking test)	-	2000	-
6.1(Maximum permissible voltage)	-	2000	-
6.2("Maximum permissible current ")	-	2000	-
6.3(Maximum permissible reactive output)	-	2000	-
7.2(Terminals and connecting cables)	-	5000	-
7.3(Earth connections)	-	5000	-
7.4(Discharge devices)	-	5000	-
9.2.1(Measurements of working voltage)	-	5000	-
9.2.2(Influence of capacitance)	-	5000	-
9.3(Checking capacitor temperature)	-	5000	-
9.4(Checking transients)	-	5000	-
9.5(Leakage current)	-	5000	-
7.1(Requirements for Creepage distances and clearances)	-	5000	-
8(Marking)	-	5000	-
7(Safety requirements)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.1.1(General)	-	0	-
5.5(Tangent of loss angle)	-	5000	-
5.7("Voltage test between terminals ")	-	5000	-
5.8(Voltage test between terminals and case)	-	2000	-
5.9(Capacitance measurement)	-	2000	-
5.1(Check of dimensions)	-	5000	-
5.11(Mechanical tests)	-	5000	-
5.12(Sealing test)	-	5000	-
5.13(Endurance test)	-	100000	-
5.14(Damp heat test)	-	110000	-
5.15(Self-healing test)	-	20000	-
5.16(Destruction test)	-	40000	-
5.17(Resistance to heat, fire and tracking)	-	25000	-
5.17.1(Ball-pressure test)	-	20000	-
5.17.2(Glow-wire test)	-	5000	-
5.17.3(Tracking test)	-	5000	-
6.1(Maximum permissible voltage)	-	5000	-
6.2("Maximum permissible current ")	-	5000	-
6.3(Maximum permissible reactive output)	-	5000	-
7.2(Terminals and connecting cables)	-	5000	-
7.3(Earth connections)	-	5000	-
7.4(Discharge devices)	-	5000	-
9.2.1(Measurements of working voltage)	-	5000	-
9.2.2(Influence of capacitance)	-	5000	-
9.3(Checking capacitor temperature)	-	5000	-
9.4(Checking transients)	-	5000	-
9.5(Leakage current)	-	5000	-
7.1(Requirements for Creepage distances and clearances)	-	5000	-
8(Marking)	-	5000	-
7(Safety requirements)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.1.1(General)	-	0	-
5.5(Tangent of loss angle)	-	5000	-
5.7("Voltage test between terminals ")	-	5000	-
5.8(Voltage test between terminals and case)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.1(Check of dimensions)	-	5000	-
5.11(Mechanical tests)	-	5000	-
5.12(Sealing test)	-	5000	-
5.13(Endurance test)	-	100000	-
5.14(Damp heat test)	-	120000	-
5.15(Self-healing test)	-	20000	-
5.16(Destruction test)	-	30000	-
5.17(Resistance to heat, fire and tracking)	-	20000	-
5.17.1(Ball-pressure test)	-	5000	-
5.17.2(Glow-wire test)	-	5000	-
5.17.3(Tracking test)	-	5000	-
6.1(Maximum permissible voltage)	-	5000	-
6.2("Maximum permissible current ")	-	5000	-
6.3(Maximum permissible reactive output)	-	5000	-
7.2(Terminals and connecting cables)	-	5000	-
7.3(Earth connections)	-	5000	-
7.4(Discharge devices)	-	5000	-
9.2.1(Measurements of working voltage)	-	5000	-
9.2.2(Influence of capacitance)	-	5000	-
9.3(Checking capacitor temperature)	-	5000	-
9.4(Checking transients)	-	5000	-
9.5(Leakage current)	-	5000	-
7.1(Requirements for Creepage distances and clearances)	-	5000	-
8(Marking)	-	5000	-
7(Safety requirements)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.1.1(General)	-	0	-
5.5(Tangent of loss angle)	-	5000	-
5.7("Voltage test between terminals ")	-	5000	-
5.8(Voltage test between terminals and case)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
5.1(Check of dimensions)	-	5000	-
5.11(Mechanical tests)	-	5000	-
5.12(Sealing test)	-	5000	-
5.13(Endurance test)	-	100000	-
5.14(Damp heat test)	-	120000	-
5.15(Self-healing test)	-	20000	-
5.16(Destruction test)	-	30000	-
5.17(Resistance to heat, fire and tracking)	-	20000	-
5.17.1(Ball-pressure test)	-	5000	-
5.17.2(Glow-wire test)	-	5000	-
5.17.3(Tracking test)	-	5000	-
6.1(Maximum permissible voltage)	-	5000	-
6.2("Maximum permissible current ")	-	5000	-
6.3(Maximum permissible reactive output)	-	5000	-
7.2(Terminals and connecting cables)	-	5000	-
7.3(Earth connections)	-	5000	-
7.4(Discharge devices)	-	5000	-
9.2.1(Measurements of working voltage)	-	5000	-
9.2.2(Influence of capacitance)	-	5000	-
9.3(Checking capacitor temperature)	-	5000	-
9.4(Checking transients)	-	5000	-
9.5(Leakage current)	-	5000	-
7.1(Requirements for Creepage distances and clearances)	-	5000	-
8(Marking)	-	5000	-
7(Safety requirements)	-	5000	-
5.9(Capacitance measurement)	-	5000	-
8(Marking)	-	-	-

05 Apr, 2027

-
Included w.e.f.04.03.2025

IS/IEC 60947 : PART 4 : Sec 3 (2020)

Low-Voltage Switchgear And Controlgear: Part 4-3 Contactors And Motor-Starters Semiconductor Controllers And Semiconductor Contactors For Non-Motor Loads

600000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.4.2.1(Test sequence V : Electrostatic discharges)	-	70000	-
9.4.2.3(Test sequence V : Fast transients (5/50 ns))	-	90000	-
9.4.2.4(Test sequence V : Surges (1,2/50 µs-8/20 µs))	-	90000	-
9.4.2.6(Test sequence V : Voltage dips and short-time interruptions)	-	70000	-
9.4.3.1(Test sequence V :Conducted radio-frequency emission test)	-	90000	-
9.4.3.3(Test sequence V : Low frequency emission test)	-	90000	-

05 Apr, 2027

-
Included w.e.f 27.02.2025 Only Test sequence V except 9.4.2.2 Radio-frequency electromagnetic field, 9.4.3.2 Radiated radio-frequency emission test

IS/IEC 60947 : Part 4 : Sec 2 (2020)

Low-Voltage switchgear and Controlgear: Part 4-2 Contactors and Motorstarters semiconductor motor controllers starters and Soft starters

600000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.4.2.1(Test sequence V : Electrostatic discharges)	-	70000	-
9.4.2.1(Test sequence V : Electrostatic discharges)	-	70000	-
9.4.2.2(Test sequence V : Radio-frequency electromagnetic field)	-	90000	-
9.4.2.3(Test sequence V : Fast transients (5/50 ns))	-	90000	-
9.4.2.4(Test sequence V : Surges (1,2/50 µs-8/20 µs))	-	90000	-
9.4.2.5(Test sequence V : Harmonics and commutation notches)	-	70000	-
9.4.2.6(Test sequence V : Voltage dips and short-time interruptions)	-	70000	-
9.4.3.1(Test sequence V : Condition for the emission tests)	-	90000	-
9.4.3.1(Test sequence V : Conducted radio frequency emission test)	-	90000	-

05 Apr, 2027

-
Included w.e.f 27.02.2025 Only Test sequence V except 9.4.2.2 Radio-frequency electromagnetic field, 9.4.3.3 Radiated radio frequency emission test

IS 18480 : Part 3 (2023)

Cross Recessed Tapping Screw Part 3 Raised Countersunk Oval Head

21000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	3000	-
Clause. 3.0(Thread size.)	-	3000	-
Clause. 3.0(Length)	-	3000	-
Clause. 4.0(Material)	-	3000	-
Clause. 4.0(Thread)	-	3000	-
Clause. 4.0(Cross Recess)	-	3000	-
Clause. 4.0(Tolerances)	-	3000	-
Clause. 4.0(Mechnical and functional properties.)	-	3000	-
Clause. 4.0(Finish)	-	3000	-
Clause. 4.0(Acceptability)	-	3000	-
Clause.5.0(Designation)	-	3000	-
Clause.5.0(Marking)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 7485 : Part 2 (2018)

Countersunk flat head screws (common head style) with type H or Type Z Cross Recess - Product Grade A part 2 Steel Screws of Property Class 8.8, Stainless Steel Screws and Non - Ferrous Metal Screws ( Third Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	3000	-
4, table 2(Material)	-	3000	-
4, table 2(Thread)	-	3000	-
4, table 2(Mechanical property)	-	3000	-
4, table 2(Tolerances)	-	3000	-
4, table 2(Cross recess)	-	3000	-
4, table 2(Finish - coating)	-	3000	-
4, table 2(Surface integrity)	-	3000	-
4, table 2(Acceptability)	-	3000	-
5(Designation)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 7485 : Part 1 (2018)

Countersunk Flat Head Screws (Common head Style) With Type H or Type Z Cross Recess - Product Grade A Part 1 Steel Screws of Property Class 4.8 ( Third Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	3000	-
4, table 2(Material)	-	3000	-
4, table 2(General requirements)	-	3000	-
4, table 2(Thread)	-	3000	-
4, table 2(Mechanical property)	-	3000	-
4, table 2(Tolerances)	-	3000	-
4, table 2(Cross recess)	-	3000	-
4, table 2(Finish - coating)	-	3000	-
4, table 2(Surface integrity)	-	3000	-
4, table 2(Acceptability)	-	3000	-
5(Designation)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 7486 (2018)

Raised countersunk head screws (Common Head Style) with type H or type Z cross recess - Product grade A (Third Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	3000	-
4, table 2(Material)	-	3000	-
4, table 2(General requirements)	-	3000	-
4, table 2(Thread)	-	3000	-
4, table 2(Mechanical property)	-	3000	-
4, table 2(Tolerances)	-	3000	-
4, table 2(Cross recess)	-	3000	-
4, table 2(Finish - coating)	-	3000	-
4, table 2(Surface integrity)	-	3000	-
4, table 2(Acceptability)	-	3000	-
5(Designation)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 7483 (2018)

Pan Head Screws With Type H or Type Z Cross Recess - Product Grade A (Third Revision)

19500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Dimensions)	-	3000	-
4, table 2(Material)	-	3000	-
4, table 2(General requirements)	-	3000	-
4, table 2(Thread)	-	3000	-
4, table 2(Mechanical property)	-	3000	-
4, table 2(Tolerances)	-	3000	-
4, table 2(Cross recess)	-	3000	-
4, table 2(Finish - coating)	-	3000	-
4, table 2(Surface integrity)	-	3000	-
4, table 2(Acceptability)	-	3000	-
5(Designation)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 18471 : Part 3 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 3 Raised Countersunk Head

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	3000	-
Clause. 3.0(Thread size.)	-	3000	-
Clause. 3.0(Length)	-	3000	-
Clause. 4.0(Material)	-	3000	-
Clause. 4.0(Thread)	-	3000	-
Clause. 4.0(Cross recesses)	-	3000	-
Clause. 4.0(Tolerances)	-	3000	-
Clause. 4.0(Mechnical and functional properties.)	-	3000	-
Clause. 4.0(Finish)	-	3000	-
Clause. 4.0(Acceptability)	-	3000	-
Clause.5.0(Designation)	-	3000	-
Clause.5.0(Marking)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 18471 : Part 2 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 2 Countersunk Head

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	3000	-
Clause. 3.0(Thread size.)	-	3000	-
Clause. 3.0(Length)	-	3000	-
Clause. 4.0(Material)	-	3000	-
Clause. 4.0(Thread)	-	3000	-
Clause. 4.0(Cross recesses)	-	3000	-
Clause. 4.0(Mechnical and functional properties.)	-	5000	-
Clause. 4.0(Finish)	-	3000	-
Clause. 4.0(Acceptability)	-	3000	-
Clause.5.0(Designation)	-	3000	-
Clause.5.0(Marking)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 18471 : Part 1 (2023)

Fasteners ï¿½ Cross Recessed Drilling Screws with Tapping Screw Thread Part 1 Pan Head

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	3000	-
Clause. 3.0(Dimenssions.)	-	3000	-
Clause. 3.0(Thread size.)	-	3000	-
Clause. 3.0(Length)	-	3000	-
Clause. 4.0(Material)	-	3000	-
Clause. 4.0(Thread)	-	3000	-
Clause. 4.0(Cross recesses)	-	3000	-
Clause. 4.0(Mechnical and functional properties.)	-	3000	-
Clause. 4.0(Finish)	-	3000	-
Clause. 4.0(Acceptability)	-	3000	-
Clause.5.0(Designation)	-	3000	-
Clause.5.0(Marking)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 18480 : Part 2 (2023)

Cross Recessed Tapping Screws Part 2 Countersunk Flat Head

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	3000	-
Clause. 3.0(Thread size.)	-	3000	-
Clause. 3.0(Length)	-	3000	-
Clause. 4.0(Material)	-	3000	-
Clause. 4.0(Thread)	-	3000	-
Clause. 4.0(Cross Recess)	-	3000	-
Clause. 4.0(Tolerances)	-	3000	-
Clause. 4.0(Mechnical and functional properties.)	-	5000	-
Clause. 4.0(Finish)	-	3000	-
Clause. 4.0(Acceptability)	-	3000	-
Clause.5.0(Designation)	-	3000	-
Clause.5.0(Marking)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 18480 : Part 1 (2023)

Cross Recessed Tapping Screws: Part 1 Pan Head

20500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 3.0(Dimenssions.)	-	3000	-
Clause. 3.0(Thread size.)	-	3000	-
Clause. 3.0(Length)	-	3000	-
Clause. 4.0(Material)	-	3000	-
Clause. 4.0(Thread)	-	3000	-
Clause. 4.0(Cross Recess)	-	3000	-
Clause. 4.0(Tolerances)	-	3000	-
Clause. 4.0(Mechnical and functional properties.)	-	3000	-
Clause. 4.0(Finish)	-	3000	-
Clause. 4.0(Acceptability)	-	3000	-
Clause.5.0(Designation)	-	3000	-
Clause.5.0(Marking)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

IS 18476 (2023)

Fasteners ï¿½ Hexagon Washer Head Drilling Screws with Tapping Screw Thread

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 4.0(Dimenssions.)	-	3000	-
Clause. 4.0(Thread size.)	-	3000	-
Clause. 4.0(Length)	-	3000	-
Clause. 5.0(Material)	-	3000	-
Clause. 5.0(Thread)	-	3000	-
Clause. 5.0(Tolerances)	-	3000	-
Clause. 5.0(Mechnical and functional properties.)	-	5000	-
Clause. 5.0(Finish)	-	3000	-
Clause. 5.0(Acceptability)	-	3000	-
Clause.6.0(Designation)	-	3000	-
Clause.6.0(Marking)	-	3000	-

05 Apr, 2027

-
Included w.e.f. 03.03.2025

1
2
3
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Conformity Testing Labs Pvt. Ltd. Unit 2

A-33, Mayapuri Industrial Area, Phase 1, New Delhi, New Delhi, New Delhi, Delhi, 110064

7840889997 qa@labctl.in

Scope List