BIS - LIMS (Laboratory Information Management System)

WELL TECH TEST AND RESEARCH CENTER, DERABASSI

INDUSTRIAL BLOCK -B , VILLAGE SAIDPURA, DERABASSI, MOHALI, S.A.S Nagar, Punjab, 140507

7973565868 wtechresearch@gmail.com

Scope List

Reset

100 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

15 -150 MM, LIGHT MED, HEAVEY, PLAIN AND SCCREWED ENDS

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Outer Diameter, Thickness & Mass)	-	6000	-
Cl 12(Workmanship)	-	6000	-
Cl. 11(Length)	-	6000	-
10.1(Thared Joints(IS:554))	-	6000	-
12.2(Galvanizing)	-	6000	-
13.0(Leak Proof Test)	-	6000	-
Clause - 6.1.1, Table-1(SULPHUR)	-	6000	-
7, 6.1.1(PHOSPHURS)	-	6000	-
7, 6.1.1(CARBON)	-	6000	-
7, 6.1.1(MANGANESE)	-	6000	-

30 Mar, 2027

-
-

IS 1161 (2014)

Steel tubes for structural purposes - Specification (Fifth Revision)

15 -350NB, GRADE YST 210-355

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Workmanship)	-	4500	-
Cl 6(Outer Diameter, Thickness & Mass)	-	4500	-
9(Straightness)	-	4500	-
Cl 11.3.1(Flattening test (over 50 mm NB))	-	4500	-
8.0(Mass of Zinc coating - IS:6745)	-	4500	-
Clause - 5.1, Table-3( CARBON)	-	4500	-
Clause - 5.1, Table-3(SULPHUR)	-	4500	-
Clause - 5.1, Table-3(PHOSPHURS)	-	4500	-
Clause - 5.1, Table-3(MANGANESE)	-	4500	-
5 AND AS PER IS 10748(CARBON EQUIVALENT)	-	4500	-
5 AND AS PER IS 10748(MICRO ALLOY)	-	4500	-
Clause - 5.1, Table-3(NITROGEN)	-	4500	-

30 Mar, 2027

-
For finished product Only above 50 mm NB

IS 710 (2010)

Marine plywood - Specification (Second Revision)

AS PER CL 6.1 UPTO 900X 2400 MM, 3MM-25 MM THICKNESS

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(WORKMANSHIP AND FINISH )	-	12500	-
6.1(DIMENSIONS)	-	12500	-
9.1.1(MOISTURE CONTENT)	-	12500	-
9.1.2 , 9.1.2.1(Glue Adhesion in Dry State)	-	12500	-
9.1.3 , 9.1.3.1.1(Water resistance test)	-	12500	-
9.1.4(Tensile strength)	-	12500	-
9.1.5 , 9.1.3.1.1(Mycological test)	-	12500	-
9.1.6 (Table 3)(Static bending strength)	-	12500	-
9.1.2 , 9.1.2.2(Glue Adhesion in Dry State)	-	12500	-
9.1.7 (Table 4)(Wet bending strength)	-	12500	-
9.1.8(Retention of preservative)	-	12500	-

30 Mar, 2027

-
-

IS 362 (1991)

Parliament Hinges -specification

TYPE 1/2/3 SIZE 50-200 MM

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type)	-	5000	-
7.1(FINISH)	-	5000	-
6.3(MANUFACTURE-Pins)	-	5000	-
6.5(MANUFACTURE-Position of Holes)	-	5000	WITHOUT RAW MATERIAL TEST

30 Mar, 2027

-
-

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	2000	-
5.4.2(a)( Aggregates Impact Value)	-	2000	-
5.4.3(a)( Aggregate Abrasion Value)	-	2000	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(coarse aggregate))	-	2000	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (coarse aggregate))	-	2000	-
5.5-IS: 2386 (P-5)(Soundness (coarse aggregate))	-	2000	-
5.3-IS: 2386 (P-1)(Combined elongation & flakiness index (coarse aggregate))	-	2000	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (coarse aggregate))	-	2000	-
5.2- TABLE-2- (iv) IS-2386 (P-2)(Soft fragments (coarse aggregate))	-	2000	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (coarse aggregate))	-	2000	-
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (coarse aggregate ))	-	2000	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (coarse aggregate ))	-	2000	-
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	2000	-
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	2000	-
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	2000	-
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	2000	-
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	2000	-
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	2000	-
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	2000	-
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	2000	-
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	2000	-
6.2-Table 7(i)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 80 mm sieve)	-	1000	-
6.2-Table 7(ii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 63 mm sieve)	-	1000	-
6.2-Table 7(iii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 40 mm sieve)	-	1000	-
6.2-Table 7(iv)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 20 mm sieve)	-	1000	-
6.2-Table 7(v)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 16 mm sieve)	-	1000	-
6.2-Table 7(vi)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 12.5 mm sieve)	-	1000	-
6.2-Table 7(vii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 10 mm sieve)	-	1000	-
6.2-Table 7(viii)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 4.75 mm sieve)	-	1000	-
6.2-Table 7(ix)(SIZE AND GRADING OF AGGREGATES- Graded Coarse Aggregates-Percentage Passing through 2.36 mm sieve)	-	1000	-
6.3-Table 9(i)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 10mm Sieve )	-	1000	-
6.3-Table 9(ii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 4.75mm Sieve )	-	1000	-
6.3-Table 9(iii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 2.36mm Sieve )	-	1000	-
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	1000	-
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	1000	-
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	1000	-
6.3-Table 9(vii)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 150µm Sieve )	-	1000	-
5.7-Table-3-(v) IS: 2386 (P-3)(specific gravity(fine aggregate))	-	1000	-
5.7-Table-3-(Iv) IS: 2386 (P-3)(Water absorption (fine aggregate))	-	1000	-
5.5-IS: 2386 (P-5)(Soundness (fine aggregate))	-	1000	-
5.2- TABLE-2- (Note-3) IS-2386 (P-2)(Mica content (fine aggregate))	-	1000	-
5.2- TABLE-2- (Note-4) IS-2386 (P-2)(Organic impurities (fine aggregate))	-	1000	-
5.2- TABLE-2- (vi) IS-2386 (P-2)(Total deleterious material (fine aggregate))	-	1000	-
5.2- TABLE-2- (iii) IS-2386 (P-1)(Material fine aggregater than 75 micron (fine aggregate))	-	1000	-
5.2- TABLE-2- (ii) IS-2386 (P-2)(Clay lumps (fine aggregate ))	-	1000	-
5.2- TABLE-2- (i) IS-2386 (P-2)(Coal and Lignite (fine aggregate ))	-	1000	-

30 Mar, 2027

-
Only for aggregate from natural resources

IS 303 (1989)

Plywood for General Purposes -

MR/BWR

4750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Minimum Individual)	-	4750	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Across the Face Grain - Average)	-	4750	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Minimum Individual)	-	4750	-
11.4, Table 4(Static Bending Strength - Modulus of Rupture - Along the Face Grain - Average)	-	4750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Minimum Individual)	-	4750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Across the Face Grain - Average)	-	4750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Minimum Individual)	-	4750	-
11.4, Table 4(Static Bending Strength - Modulus of Elasticity - Along the Face Grain - Average)	-	4750	-
11.2.2(Glue Adhesion - Mycological test - 11.2.2, Part 7 of IS 1734 [for MR Garde only])	-	4750	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for MR Grade])	-	4750	-
11.2.1(Glue Adhesion - Water resistance test - 11.2.1.1 [for BWR Grade])	-	4750	-
11.3(Moisture Content - Part 1 of IS 1734)	-	4750	-
8(Dimensions & Tolerances - Edge Straightness - Annexure C)	-	4750	-
8(Dimensions & Tolerances - Squareness - Annexure C)	-	4750	-
8(Dimensions & Tolerances - Thickness - Cl. 8)	-	4750	-
8(Dimensions & Tolerances - Width - Cl. 8)	-	4750	-
8(Dimensions & Tolerances - Length - Cl. 8)	-	4750	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	4750	-
9(Workmanship and Finish - Cl.9, 8.3, Annexure C)	-	4750	-
5.2, Table 1, Table 2(Quality Requirements - Cl. 5.2)	-	4750	-

30 Mar, 2027

-
-

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

2.0-10,00 MM

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 AND AS PER IS 7887(CARBON)	-	6500	-
6 AND AS PER IS 7887(SILICON)	-	6500	-
6 AND AS PER IS 7887(MANGANESE)	-	6500	-
6 AND AS PER IS 7887(PHOSPHORUS)	-	6500	-
6 AND AS PER IS 7887(ALUMINIUM)	-	6500	-
6 AND AS PER IS 7887(SULPHUR)	-	6500	-
9.2(Wrapping Test)	-	6500	-
Cl 11(Workmanship)	-	6500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	6500	-
Cl 9(Tensile Test On UTM)	-	6500	-
Clause 6 and Note 3 of IS 7887(Copper)	-	6500	-
9.3(Bend test)	-	6500	-
11(Coating test)	-	6500	-

30 Mar, 2027

-
-

IS 205 (1992)

Non - Ferrous metal butt specification (Fourth Revision)

HING DESIGNATION AS PER TABLE 2-5

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	6000	-
5.1- Table 2,3,4,5 & Fig-1 & 2(Dimensions- Type of Hinge 1.Length 2.Breadth 3.Butt Dia 4.Pin Dia 5.Thickness of Flap)	-	6000	-
6.2- Table 2,3,4,5 (Kunckles)	-	6000	-
6.3(Screw Holes)	-	6000	-

30 Mar, 2027

-
-

IS 204 : Part 2 (1992)

Tower bolts - Specification: Part 2 non - Ferrous metals (Fifth Revision)

TYPE AS PER CL.3 AND SIZE AS PER TABLE 1-2

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(General)	-	6000	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Copper - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Aluminium - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Magnesium - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Silicon - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Iron - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Manganese - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Zinc - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8 , Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Titanium - IS 504)	-	6000	-
4 -Table 3- i (Ref. Cl 8, Table 1 Designation 63400 of IS 1285 : 2002)(Chemical composition - Chromium - IS 504)	-	6000	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Lead - IS 3635:1966)	-	6000	-
4 -Table 3- iii (Ref. Cl 6.1 , Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Copper - IS 3635:1966)	-	6000	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt or Barrel-(A or B) 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of Metal of Barrel (Brass or Zink Alloy/Aluminium alloy/Sheet Brass)-F 8.Dia of bore of barrel or socket- G )	-	6000	-
6.2- Table 2(Dimension of Skeleton Tower Bolts 1.Size 2.Length of Bolt -A 3.Length of Bolt Plate -B 4.Width of Bolt Plate or Staple-C 5.Dia of Bolt-D 6.Length of Staple-E 7.Thickness of Plate or Socket (Brass /Aluminium alloy or Zink Alloy)-F 8.Dia of bore of Plate or Staple-G 9.Dia of shank of Knob )	-	6000	-
7(Finish)	-	6000	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Iron - IS 3635:1966)	-	6000	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Total impurities (including Iron) - IS 3635:1966)	-	6000	-
4 -Table 3- iii (Ref. Cl 6.1, Table 1 Designation CuZn40 of IS 410 : 1977)(Chemical composition - Zinc - IS 3635:1966)	-	6000	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Copper plus incidental nickel - IS 3685:1966)	-	6000	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Nickel - IS 3685:1966)	-	6000	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Tin - IS 3685:1966)	-	6000	-
4 -Table 3- iv (Ref. Cl 3.1, Table 1 Grade CB-2 of IS 292 : 1983)(Chemical composition - Aluminium - IS 3685:1966)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Aluminium- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Magnesium- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Copper- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Iron- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Lead- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Cadmium- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Tin- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Zinc- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Nickel- IS 2600:1964)	-	6000	-
4 -Table 3- vi (Ref. Cl 4.1, Table 1 Alloy ZnAl4 of IS 742 : 1981)(Chemical composition - Impurities-Thallium and Indium- IS 2600:1964)	-	6000	-

30 Mar, 2027

-
-

100

IS 204 : Part 1 (1991)

Tower bolts - Specification: Part 1 ferrous metals (Fifth Revision)

TYPE AS PER CL.3 & SIZE AS PER TABLE 1, 2, 3

5000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Carbon - IS 228)	-	5000	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Manganese - IS 228)	-	5000	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Phosphorus - IS 228)	-	5000	-
4 -Table 5- i (Ref. Cl 7, Table 3, HR1 grade of IS 1079 : 2017)(Chemical composition - Sulphur - IS 228)	-	5000	-
4 -Table 5- ii (Ref. Cl 5, Table 1, E300-C grade of IS 2062 : 2011)(Chemical composition - Silicon - IS 228)	-	5000	-
4 -Table 5- iii (Ref. Cl 6.1 of IS 210 : 2009)(Chemical composition - Sulphur and/or Phosphorous)	-	5000	-
5.1(General)	-	5000	-
6.1- Table 1(Dimension of Barrel tower bolts-1.Size 2.Length of Bolt-A 3.Length of Barrel-B 4.Width of Barrel-C 5.Dia of Bolt-D 6.Length of Socket-E 7.Thickness of mild steel sheet for barrel-F 8.Dia of bore of barrel or socket- G )	-	5000	-
7(Finish)	-	5000	-

30 Mar, 2027

-
-

Bureau of Indian Standards

The National Standards Body of India

WELL TECH TEST AND RESEARCH CENTER, DERABASSI

INDUSTRIAL BLOCK -B , VILLAGE SAIDPURA, DERABASSI, MOHALI, S.A.S Nagar, Punjab, 140507

7973565868 wtechresearch@gmail.com

Scope List