BIS - LIMS (Laboratory Information Management System)

CIPET, Vijayawada

SY NO. 377, SURAMPALLY X ROAD, GANNAVARAM MANDAL, VIJAYAWADA, VIJAYAWADA, Krishna, Andhra Pradesh, 521212

8093140230 vijayawada@cipet.gov.in

Scope List

Reset

49 Results

S.No.

Indian Standard No.

Product

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 11652 (2017)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg cement – Specification (third revision)

29380 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 (width of tape, 2.5 mm ± 0.1 mm)	-	500	-
Fig. 1- Table 1- Sr. no. ii (Ends per dm - Annex B 40 ± 2 )	-	500	-
Fig. 1- Table 1-Sr. no. iii (Picks per dm-Annex B 40 ± 2 )	-	500	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note )- Annex B c) Width of gusset (e) 76 ± 10 mm )	-	500	-
Fig. 1- Table 1- Sr. no. i (Dimensions, mm (see Note ) -Annex B d) Width of valve (v) 100, + 10/-5 mm )	-	0	-
Fig. 1- Table 1-Sr. no. i (Dimensions, mm (see Note )- Annex B b) Width of sack (w) 480 ± 10 mm )	-	0	-
Fig. 1, Table 1 (i) Dimensions, mm (see Note ) -Annex B a) Length of sack, inside (l), 710 ± 10 mm )	-	0	-
4.5(and the remaining overhang shall not be more than 5 mm after trimming.)	-	500	-
4.1(Raw Material )	-	500	-
4.2 (Fabric)	-	500	-
4.2 (Linear Density, 900 denier)	-	500	-
4.2 (The woven fabric shall be of mesh, 10 × 10 per inch)	-	0	-
4.2 (The woven fabric shall be of weight, 79 g/m2 )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: a) ± 10 percent on individual value, and )	-	0	-
4.2 (The denier of HDPE/ PP tape used in the manufacture of woven fabric shall be subjected to the tolerances: b) ± 5 percent on average. )	-	0	-
4.3(Sacks)	-	500	-
4.4(Seam )	-	500	-
4.4(Seam The two rows of stitches shall be separated from each other by minimum 5 mm and )	-	500	-
4.4(Seam The outer stitch shall be minimum 8 mm from the outer edge of the sacks. )	-	0	-
4.4(Seam The stitching shall be done with double fold over seam to)	-	500	-
4.4(to a depth of minimum 25 mm, so that so that)	-	0	-
4.4(that the stitches pass through a minimum of six layers of the fabric.)	-	0	-
4.4(The number of stitches/dm shall be 14 ± 2.)	-	0	-
4.4(The material used for stitching shall be HDPE/PP tape having minimum 20 percent higher denier than the tapes used in the fabric.)	-	1050	-
4.4(Seam)	-	0	-
4.5(Lamination )	-	1050	-
4.6(Capacity The sack shall have the nominal filling capacity of 50 kg)	-	500	-
4.7(Valve for Filling of Sacks)	-	500	-
5/5.1-Table 1-Sr. no. iv(Requirements, Mass of Sack- IS 1964 a) Non-gusseted type 70 + 6%)	-	0	-
5/5.6 (UV Resistance, )	-	10180	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): -1969 (Part 1) a) Lengthwise , 900 (91.8) )	-	1300	-
5/5.3-Table 1-Sr. no.v(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70 mm] Min, N(kgf): - 1969 (Part 1) b) Widthwise , 900 (91.8) )	-	1300	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of top seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1300	-
5/5.3-Table 1-Sr. no.vi(Breaking strength of bottom seam (Ravelled strip method), Min, - IS 9030 N (kgf) 400 (40.8))	-	1300	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) a) Lengthwise 15 to 25)	-	0	-
5/5.3-Table 1-Sr. no.vii(Elongation at break of fabric (Ravelled strip method), percent : - IS 1969 (Part1 ) b) Widthwise 15 to 25)	-	0	-
5/5.4-Table 1-Sr. no.viii(Drop impact strength - Annex C No failure)	-	1100	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D a) For UV stabilized sacks 2.2 )	-	1200	-
5/5.5-Table 1-Sr. no.viii(Ash content Max percent- Annex D b) For non-UV stabilized sacks 6 )	-	0	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to a) UV Radiation -Annex F )	-	1300	-
5/5.6 (UV Resistance, The UV stabilized woven fabric shall have at least 50 percent retention of the original breaking strength when tested after the same has been exposed to b) Accelerated Weathering - Annex F )	-	1300	-

Complete

06 Jun, 2024

IS 17546 (2021)

Chlorinated polyvinyl chloride CPVC fittings for potable hot and cold water distribution supplies Specification

163225 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Nominal Size(DN))	-	500	-
3.2(Nominal Outside Diameter)	-	2000	-
3.3(Mean Inside Diameter of Socket at Entry)	-	1400	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	2000	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	700	-
3.5(Out-of-Roundness (Ovality))	-	700	-
3.6(Nominal Wall Thickness)	-	700	-
3.7(Minimum Wall Thickness)	-	875	-
3.11(Type Tests)	-	15800	-
3.11(Acceptance Tests)	-	1100	-
7(Dimensions of fitting)	-	850	-
8.2(Opacity)	-	1100	-
8.1(Visual Appearance)	-	1275	-
8.3(Stress Relief Test)	-	2000	-
8.4(Vicat softening Temperature)	-	1100	-
8.5(Density)	-	1500	-
8.6(Effect on water)	-	3000	-
9(Mechanical Properties)	-	16900	-

Complete

06 Jun, 2024

IS 16098 Part 2 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 2 Pipes and Fittings with Non-Smooth External Surface, Type B

116820 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 Table-10 (i)(Ring Stiffness)	-	1100	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	500	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	1100	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	2200	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	1100	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	4800	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	11000	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	1100	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	250	-
6.3.2(Length of Pipe)	-	250	-
8.1.1 Table-10 (iv)(Creep ratio)	-	1100	Creep Ratio ( 1008 hrs x 25)= 25200
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	1000	-
6.3.5.2(Wall Thickness(e4 min))	-	25	-
7.1(Appearance)	-	300	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	1100	-

Complete

06 Jun, 2024

IS 15532 (2004)

Plastics crates for fruits and vegetables - Specification

9558 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Material)	-	1050	-
3.5(Appearance and Surface Finish)	-	300	-
3.3(Shape, Dimensions and Design)	-	500	-
3.4(Mass)	-	250	-
3.6(Dimensional Stability)	-	700	-
3.7(Confluence Line Strength)	-	1000	-
3.8.1(Compressive Strength (Resistance to Applied Load))	-	1100	-
3.8.2(Resistance to Drop)	-	1000	-
3.9(Resistance to Environmental Stress Cracking)	-	1200	-
3.10.2(Free-Fall Test)	-	1000	-

Complete

06 Jun, 2024

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

17268 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 Table 1(Dimensions)	-	200	-
5.2 Table 1(Dimensions)	-	200	-
5.2 Table 1(Dimensions)	-	100	-
5.2 Table 1(Dimensions)	-	100	-
5.2 Table 1(Ends per dm)	-	200	-
5.2 Table 1(Picks per dm)	-	200	-
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	500	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	1500	-
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N2) (kgf): - IS 1969 (Part 1))	-	1500	-
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1500	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	1500	-
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	1500	-
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,b) For non- UV stabilized sacks)	-	1000	For UV Stabilized sacks and Non-UV stabilized sacks purpose

Complete

06 Jun, 2024

IS 10889 (2004)

High density polyethylene films (First Revision)

11525 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials)	-	1250	-
5.2(Black Compound)	-	975	-
6.1.1(Appearance)	-	300	-
6.1.2(Film Form)	-	300	-
6.1.3(Odour )	-	300	-
6.1.4(Density)	-	500	-
6.1.5(Melt Flow Rate)	-	1100	-
6.1.6(Black Film)	-	300	-
6.2.1, Table 1(Nominal Thickness)	-	500	-
6.2.2, Table 2(Nominal Width)	-	500	-
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	500	-
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	500	-
6.3, Table 3(Yield Tolerance)	-	600	-
6.4.1(Tensile Strength at Break)	-	1100	-
6.4.2(Elongation at Break)	-	1100	-
6.4.3(Impact Resistance (Falling Dart))	-	850	-
6.4.3, Table 6(Average Thickness of Film)	-	500	-

Complete

06 Jun, 2024

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

37025 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.4, annexure-E( Orientation Factor)	-	1000	-
5.5( Density, g/cc)	-	500	-
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	1000	-
7.3( Opacity)	-	500	-
9.2, table -11( Resistance to External Blows at 0 °C)	-	1000	-
8.2 table-9( Pipe Ends)	-	300	-
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	500	-
8.1.2, table 4 to 7(Wall Thickness)	-	500	-
8.1.3 (Length, meter)	-	500	-
8.2 table-9(Dimensions of Integral Socket)	-	500	-
9.3 table-12( Ring Stiffness)	-	1100	-
11.2 / 11.2.1( Short-Term Pressure Test for Leak Tightness of Assemblies)	-	1000	-
12(b)( ELASTOMERIC SEALS)	-	375	-

Complete

06 Jun, 2024

IS 4985 (2000)

Unplasticized pvc pipes for potable water supplies - Specification (Third Revision)

15856 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
11.2(Resistance to External Blows at 0°C)	-	1000		-

Complete

06 Jun, 2024

IS 10124 : Part 3 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 3 Specific Requirements for Straight Reducers

- View breakup
Rs.1444/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 5 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 5 specific requirements for equal tees (Second Revision)

- View breakup
Rs.1444/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 7 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 7 specific requirements for threaded adaptors (Second Revision)

- View breakup
Rs.1744/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 8 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 8 specific requirements for 90 degree bends (Second Revision)

- View breakup
Rs.1444/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 9 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 9 specific requirements for 60 degree bends (Second Revision)

- View breakup
Rs.1444/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 10 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 10 specific requirements for 45 degree bends (Second Revision)

- View breakup
Rs.1444/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 11 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 11 specific requirements for 40 degree bends (Second Revision)

- View breakup
Rs.1444/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 13 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 13 Specific Requirements for 11Â¼oBends PART 12 SPECIFIC REQUIREMENTS FOR 22 Â½o BENDS

- View breakup
Rs.1444/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 4 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 4 specific requirements for caps (Second Revision)

- View breakup
Rs.1744/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

- View breakup
Rs.45613/- (with Elastometric sealing ring), Rs.45713/- (With solvent cement)

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 9755 (2016)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing fertilizers – Specification (fifth revision)

- View breakup
Rs.20605/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 7834 : Part 2 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 2 Specific requirements for 45 degrees elbows

- View breakup
Rs.4219/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

- View breakup
Rs.4219/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

- View breakup
Rs.4219/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

- View breakup
Rs.4219/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

- View breakup
Rs.4219/-,

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

- View breakup
Rs.4219/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 12100 (1987)

Specification for high density polyethylene (HDPE) woven sacks for packing flour

- View breakup
Rs.9000/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

IS 15450 (2004)

Polyethylene/aluminium/polyethylene composite pressure pipes for hot and cold water supplies - Specification

16069 View breakup
Product - Rs 16069 /- Raw Material Rs 3044 /- Aluminium – Rs 1263 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8, Table-2(Dimension)	-	250	NIL
10.1(Density )	-	500	NIL
10.6(Apparent tensile strength of pipe)	-	1600	INCLUDES SPECIMEN CHARGE
10.7(minimum burst pressure)	-	1000	NIL
Clause 10.3 table 3(Carbon black content)	-	925	NIL
table 3(anti oxidant content)	-	0	NIL

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

15000 View breakup
Product - Rs 15000 /- Raw Material Rs 900 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1200	NIL
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	500	NIL
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	0	NIL
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	0	NIL
6.1.3 (Length of Pipe)	-	0	NIL
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	0	NIL
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	0	NIL
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	0	NIL
6.1.4, Table 3(iv) Length of spigot, l1)	-	0	NIL
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	0	NIL
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	0	NIL
6.1.4.1 (e3min=0.75e)	-	0	NIL
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	0	NIL
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	0	NIL
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	0	NIL
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	0	NIL
7(Physical characteristics )	-	0	NIL
7.1(Appearance:- )	-	300	NIL
7.2(Colour )	-	300	NIL
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1100	NIL
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1000	INCLUDES SPECIMEN CHARGE
8(MECHANICAL CHARACTERISTICS)	-	0	NIL
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1400	INCLUDES SPECIMEN CHARGE
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1400	INCLUDES SPECIMEN CHARGE
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	850	NIL
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	11000	NIL
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	0	NIL
9.2 IS 14182(b) Solvent cement)	-	0	NIL
10(Performance requirements)	-	0	NIL
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	850	NIL
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	NIL
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	850	NIL
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1000	NIL

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

IS 14885 (2001)

Polyethylene pipes for the supply of gaseous fuels - Specification

45125 View breakup
Rs 45125 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.4(Colour)	-	300	NIL
Table-2, 5.1(Conventional Density, IS 7328:1992)	-	500	NIL
Table-2, 5.1(Melt Flow Rate, IS 2530:1963)	-	1100	NIL
Table-2, 5.1(Thermal Staibility, Annex-D)	-	2200	NIL
Table-2, 5.1(Resistance to gas constituents, Cl 5.5)	-	6250	INCLUDES CONDITIONING
Table-2, 5.1(Pigment dispersion, Annex-E)	-	600	NIL
5.2(Anti Oxidant: Cl. 17 of IS 2530)	-	0	NIL
5.3(U.V.Stabilizer)	-	0	NIL
6.1, Table-3(Ovality Pipe, Cl 6.3.2)	-	500	NIL
6.1, Table-3(Nominal Outside Diameter of Pipes , Cl 6.3.1)	-	0	INCLUDED IN 6.1
6.2.1, Table-4(Minimum Wall Thickness, Cl.6.3, Cl.6.2.1.1, Table-5)	-	0	INCLUDED IN 6.1
6.4(Length of pipe)	-	0	INCLUDED IN 6.1
7, Table-6(Maximmn Out of Square of Each Pipe End)	-	0	INCLUDED IN 6.1
8.1(Hydraulic Charactristics, Annex-A)	-	20300	INCLUDES SPECIMEN CHARGE
8.2(Reversion Test. Annex-C)	-	700	NIL
8.3(Density, Annex A of IS 7328)	-	500	NIL
8.4(Melt Flow Rate (MFR), IS 2530)	-	1100	NIL
8.5(Thermal Stability to Oxidation, Annex-D)	-	2200	NIL
8.7(Tensile yield strength, Annex-J)	-	1350	NIL
8.7(Elongation at break, Annex-J)	-	1350	NIL
8.8(Resistance to Weathering, Annex-F)	-	12550	NIL
8.9(Squeeze off, Annex-G)	-	6100	NIL
8.6 & Table-2(Volatile Content: Annex-H of IS 14885)	-	700	NIL
8.5 & Table-2(Thermal Stability to Oxidation, Annex-D of IS 14885)	-	2200	NIL

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

7438 View breakup
Product - Rs 7438 /- Material Rs 1725 /- Rubber Ring – Rs 1069 /-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
19(Marking)	-	0	NIL
3(Type of Fitting)	-	0	NIL
4(Size Designation)	-	0	NIL
5(Colour of fittings)	-	300	NIL
7.1,Table 1(Wall thickness)	-	500	NIL
7.2 ,Table 2&3(Socket Dimensions)	-	0	INCLUDED IN 7.1
7.3(Dimensions of waste trap(Nahani Trap)	-	0	NIL
8(Sealing Rings)	-	1425	NIL
10(Workmanship)	-	300	NIL
11(Design requirements)	-	0	NIL
11.1(Solvent cement type or Rubber ring type)	-	0	NIL
11.2(Socket and spigot configeration)	-	0	NIL
11.4,Table 5(Vent cowl)	-	0	NIL
11.5,Table 6(Pipe Clips)	-	0	NIL
12(Physical test requirements)	-	0	NIL
12.1(Visual appearance)	-	300	NIL
12.2(Stress relief test)	-	700	NIL
12.3(Vicat softening tempewrature)	-	1100	NIL
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	2500	INCLUDES CONDITIONING CHARGE
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1200	NIL
Cl.15, Annex B(Sulphated Ash Content)	-	850	NIL
16(Mechanical Properties)	-	0	NIL
16.1(Impact test)	-	1000	NIL
17(Watet tightness of joint)	-	1000	NIL

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

Bureau of Indian Standards

The National Standards Body of India

CIPET, Vijayawada

SY NO. 377, SURAMPALLY X ROAD, GANNAVARAM MANDAL, VIJAYAWADA, VIJAYAWADA, Krishna, Andhra Pradesh, 521212

8093140230 vijayawada@cipet.gov.in

Scope List

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found

No Record Found