BIS - LIMS (Laboratory Information Management System)

CIPET, Vijayawada

SY NO. 377, SURAMPALLY X ROAD, GANNAVARAM MANDAL, VIJAYAWADA, VIJAYAWADA, Krishna, Andhra Pradesh, 521212

7077573905 vijayawada@cipet.gov.in

Scope List

Reset

52 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Exclusion

Testing Charges (Excl. Of Taxes)

Facility Type

Effective Date

Validity Date

Remark

IS 12100 (1987)

Specification for high density polyethylene (HDPE) woven sacks for packing flour

Type-1 & 2

7400 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1, Table 1(Breaking strength of fabric on 5 × 20 cm strip, Widthwise)	-	1600	NIl
3.1, Table 1(Breaking strength of fabric on 5 × 20 cm strip, Lengthwise)	-	1600	NIl
3.1, Table 1(Seam breaking strength, Side team)	-	1600	NIl
3.1, Table 1(Seam breaking strength, Bottom team)	-	1600	NIl
3.2(Dimensions)	-	500	NIl
3.3(Mass)	-	500	NIl

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

IS 15328 (2003)

Unplasticized Non-Pressure Polyvinyl Chloride ( PVC -U ) Pipes for use in Underground Drainage and Sewerage Systems -

63-630MM, STIFFNESS 2,4,8KN/M2

24250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,5.2(Composition of the material The material shall contain a minimum of 0.3 percent of rutile grade titanium dioxide.)	-	1200	NIL
6.1,6.1.1 IS 12235 (Part 1) Table 1(Dimension of Pipes: Mean outside Diameter, dem)	-	500	NIL
6.1,6.1.1 IS 12235 (Part 1) Table 1(Outside Diameter at any point, de)	-	0	NIL
6.1.2 IS 4985 Table 2(Wall Thickness, e )	-	500	NIL
6.1.3 (Length of Pipe)	-	0	NIL
6.1.4, Table 3(Dimensions of integral sockets and spigot ends :- a) Elastomeric Sealing Ringsockets and spigot ends i)Meean inside dia. Of socket, dsm)	-	0	NIL
6.1.4, Table 3(ii) Min. depth of engagement, A. )	-	0	NIL
6.1.4 Table 3(iii) Depth of sealing Zone C )	-	0	NIL
6.1.4, Table 3(iv) Length of spigot, l1)	-	0	NIL
6.1.4, Table 3(v) Chamfer length, H : Approx.)	-	0	NIL
6.1.4.1 (wall thickness of sockets e2 min=0.9e )	-	0	NIL
6.1.4.1 (e3min=0.75e)	-	0	NIL
6.1.4, Table 4(b) Solvent Cement Joint sockets and spigot ends i) Mean inside dia. Of socket, dsm)	-	0	NIL
6.1.4, Table 4(ii) Length of Solvent Cement socket, l2 )	-	0	NIL
6.1.4, Table 4(iii) Length of spigot, l1, 100 mm Min.)	-	0	NIL
6.1.4, Table 4(iv) Chamfer length, H, 7 mm Approx.)	-	0	NIL
7(Physical characteristics )	-	0	NIL
7.1(Appearance:- )	-	500	NIL
7.2(Colour )	-	500	NIL
7.3 IS 1223S ( Part 2)(Vicat Softening Temperature When determined according to IS 1223S ( Part 2), shall not be lessthan 79°C.)	-	1100	NIL
7.4 IS 1223S ( Part 5)(Longitudinal Reversion: When tested according to the methodprescribed in IS 1223S ( Part 5), shall not exceed ± 5 percent. The pipe shall not exhibit any blisters, bubbles or crackson completion of the test.)	-	1200	INCLUDES SPECIMEN CHARGE
8(MECHANICAL CHARACTERISTICS)	-	0	NIL
8.1 Annex B(Resistance to External Blows at 0ºC: When tested according to the method prescribed in Annex B, the pipes hall have a true impact rate of not more than I0 percent.)	-	1600	INCLUDES SPECIMEN CHARGE
8.2 Annex C Table 5(Ring Stiffness: When tested according to the method described in Annex C,the ring stiffness of the pipe shall be as stated in Table 5)	-	1600	INCLUDES SPECIMEN CHARGE
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(Resistance to internal Hydrostatic Pressure(Type Test) a) Acceptance Test:(1h at 27 0 C) )	-	850	NIL
8.3 IS 12235 ( Part 8/ Sec 1 ) Table 6(b) Type Test:(1000h at 60 0 C) )	-	11000	NIL
9 9.1, IS 5382(JOINTS:- a) Elastomeric Sealing Rings)	-	0	NIL
9.2 IS 14182(b) Solvent cement)	-	0	NIL
10(Performance requirements)	-	0	NIL
10.1.1 Annex D(Internal hydrostatic pressure test for elastomeric sealing ring joints)	-	850	NIL
10.1.2 Annex E(Internal negative hydrostatic pressure test (internal vacuum) for elastomeric sealing ring joints)	-	1000	NIL
10.2.1(Internal hydrostatic pressure test for solvent cemented Joints)	-	850	NIL
10.2.2(Internal negative hydrostatic pressure test (internal vacuum)for solvent cemented joints)	-	1000	NIL

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

UPTO 160MM

14650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
19(Marking)	-	0	NIL
3(Type of Fitting)	-	0	NIL
4(Size Designation)	-	0	NIL
5(Colour of fittings)	-	500	NIL
7.1,Table 1(Wall thickness)	-	500	NIL
7.2 ,Table 2&3(Socket Dimensions)	-	0	INCLUDED IN 7.1
7.3(Dimensions of waste trap(Nahani Trap)	-	0	NIL
8(Sealing Rings)	-	500	NIL
10(Workmanship)	-	500	NIL
11(Design requirements)	-	500	NIL
11.1(Solvent cement type or Rubber ring type)	-	0	NIL
11.2(Socket and spigot configeration)	-	0	NIL
11.4,Table 5(Vent cowl)	-	0	NIL
11.5,Table 6(Pipe Clips)	-	0	NIL
12(Physical test requirements)	-	0	NIL
12.1(Visual appearance)	-	500	NIL
12.2(Stress relief test)	-	700	NIL
12.3(Vicat softening tempewrature)	-	1100	NIL
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	2500	INCLUDES CONDITIONING CHARGE
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1200	NIL
Cl.15, Annex B(Sulphated Ash Content)	-	1200	NIL
16(Mechanical Properties)	-	0	NIL
16.1(Impact test)	-	1100	NIL
17(Watet tightness of joint)	-	850	NIL
12.4(Effect on water test)	-	3000	NIL

Complete

06 Jun, 2024

Included w.e.f 13.08.2019. Testing charges has been fixed for two years w.e.f. 13.08.2019 to 12.08.2021

IS 16208 (2015)

Textiles - High density polyethylene (HDPE)/polypropylene (PP) woven sacks for packaging 10 kg, 15 kg, 20 kg, 25 kg and 30 kg foodgrains - Specification

HDPE/PP, CAPACTY: 10, 15,20,25 & 30KG

22630 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	NIL
4.1(Raw Material)	-	1050	NIL
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	NIL
4.2(Tapes – Linear Density )	-	700	NIL
4.2(Construction)	-	500	NIL
4.3(Sacks)	-	500	NIL
4.3.1(Bottom Seam)	-	0	NIL
4.3.1( The two rows of stitches shall be separated from each other)	-	0	NIL
4.3.1( The outer stitch)	-	0	NIL
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	NIL
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	NIL
4.3.1(The number of stitches/dm)	-	0	NIL
4.3.2(Mouth)	-	0	NIL
4.4 and Table 1 i(Capacity)	-	500	NIL
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	NIL
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	NIL
5.2 and Table 1 iii(Ends per dm )	-	500	NIL
5.2 and Table 1 iv(Picks per dm )	-	500	NIL
5.1 and Table 1 v(Mass of sack )	-	500	NIL
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise )	-	1100	NIL
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise )	-	1100	NIL
5.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	NIL
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise)	-	0	INCLUDES IN BREAKING STRENGTH
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise )	-	0	INCLUDES IN BREAKING STRENGTH
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	INCLUDES UV CONDITIONING CHARGE
5.2 and Table 1 x(Ash content )	-	1200	NIL

Complete

06 Jun, 2024

0.0

IS 14968 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packing 50 Kg/25 kg sugar – Specification (first revision)

SIZE 25 & 50 KG

23130 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(TYPES)	-	0	NIL
4.1(Raw Material)	-	1050	NIL
4.2(Tapes – Width IS 6192 and IS 11197)	-	500	NIL
4.2(Tapes – Linear Density )	-	700	NIL
4.2(Construction)	-	500	NIL
4.3(Sacks)	-	500	NIL
4.3.1(Bottom Seam)	-	500	NIL
4.3.1(The two rows of stitches shall be separated from each other)	-	0	NIL
4.3.1( The outer stitch)	-	0	NIL
4.3.1( The stitching shall be done with double fold over seam to a depth )	-	0	NIL
4.3.1(Stitches pass through a minimum of six layers of the fabric. )	-	0	NIL
4.3.1(stitches/dm)	-	0	NIL
4.3.2(Mouth)	-	0	NIL
4.4(Liner IS 10146 or IS 10910.)	-	0	NIL
4.4(Mass of the loose liner )	-	0	NIL
4.4(Width of the loose liner)	-	0	NIL
4.4(Length of the line)	-	0	NIL
4.4(Bottom seam of the loose liner)	-	0	NIL
4.4.1(Liner)	-	0	NIL
4.5 and Table 1 i(Capacity)	-	500	NIL
5.2 and Table 1 ii a(Dimensions Inside Length)	-	500	NIL
5.2 and Table 1 ii b(Dimensions Inside Width)	-	0	NIL
5.2 and Table 1 iii(Ends per dm )	-	500	NIL
5.2 and Table 1 iv(Picks per dm )	-	500	NIL
5.1 and Table 1 v a(Mass of unlaminated sack IS 1964)	-	500	NIL
5.1 and Table 1 v b(Mass of unlaminated sack with liner )	-	0	NIL
5.2 and Table 1 vi a(Average breaking strength of fabric Lengthwise IS 1969 (Part 1))	-	1100	NIL
5.2 and Table 1 vi b(Average breaking strength of fabric Widthwise IS 1969 (Part 1))	-	1100	NIL
5.2 and Table 1 vi(Breaking strength of bottom seam IS 9030 )	-	1100	NIL
5.2 and Table 1 viii a(Elongation at break of fabric Lengthwise IS 1969 (Part 1))	-	0	NIL
5.2 and Table 1 viii b(Elongation at break of fabric Widthwise IS 1969 (Part 1))	-	0	NIL
5.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	INCLUDES UV CONDITIONING CHARGE
5.2 and Table 1 x(Ash content )	-	1200	NIL

Complete

06 Jun, 2024

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

HDPE/PP , CAPACITY 50KG

28380 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	500	NIL
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	500	NIL
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	500	NIL
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	NIL
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1700	NIL
3.2(Tapes – Colour Fastness for pigmented tapes (IS 6192/IS 11197))	-	1000	NIL
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1000	NIL
3.2(Unlaminated Fabric Mass )	-	500	NIL
3.3.1(Bottom seam (IS 10789))	-	2700	INCLUDES ALL SEAM TESTS
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	500	NIL
4.2 and Table 1 ii(Dimensions )	-	500	NIL
5.2 and Table 1 iii(Ends per dm )	-	500	NIL
5.2 and Table 1 iv(Picks per dm )	-	500	NIL
4.2 and Table 1 v(Mass of sack )	-	500	NIL
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	LENGTH & WIDTH WISE
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	NIL
4.2 and Table 1 viii(Elongation at break of fabric )	-	0	INCLUDES IN BREAKING STRENGTH
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	INCLUDES SPECIMEN CONDITIONING CHARGES
4.2 and Table 1 x(Ash content )	-	1200	NIL

Complete

06 Jun, 2024

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

HDPE OR PP

25930 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	1050	NIL
3.2(Tapes – Width )	-	500	NIL
3.2(Tapes – Linear Density )	-	700	NIL
3.3(Tying Cord)	-	500	NIL
3.4(Sack)	-	500	NIL
3.4.1(Seam)	-	2700	INCLUDED ALL SEAM TESTS
4.1 and Table 1 i a(Dimensions Outside Length)	-	500	NIL
4.1 and Table 1 i b(Dimensions Outside Width)	-	0	INCLUDED IN 4.1
4.1 and Table 1 ii(Ends per dm )	-	500	NIL
4.1 and Table 1 iii(Picks per dm )	-	500	NIL
4.2 and Table 1 iv(Mass of sack )	-	500	NIL
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	NIL
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	1100	NIL
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	2200	INCLUDES TOP & BOTTOM SEAM
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	0	INCLUDES IN 4.1
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	0	INCLUDES IN 4.1
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	12380	INCLUDES WEATHERING CHARGES OF RS 10180
4.1 and Table 1 ix(Ash content )	-	1200	NIL

Complete

06 Jun, 2024

0.0

IS 13592 (2013)

Unplasticized Polyvinyl Chloride (PVC-U) Pipes for Soil and Waste Discharge System Inside and Outside Buiildings Including Ventilation and Rainwater System

UPTO 315MM, TYPE -A & B, PLAIN & GROOVED SOCKET

19200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.5(Surface colour of the pipes shall be dark shade of grey)	-	500	NIL
Cl6.3(The composition shall be based on PVC resin having a K-value of 64 or greater when tested in accordance with IS 4669)	-	1100	NIL
Cl.7.1(Mean outside diameter, outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	500	NIL
Cl.7.1( outside diameter at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	INCLUDED IN 7.1
Cl.7.1( wall thickness at any point for Type A and Type B pipes manufactured plain or with socket shall be as given in Table 1. Dimensions shall be measured according to the method given in IS 12235 (Part 1).)	-	0	INCLUDED IN 7.1
Cl.7.2(Pipes shall be supplied in nominal lengths of 2, 3, 4 or 6 metres either plain or with socket for solvent cementing/grooved socket. Tolerances on specified length shall be + 10 mm and – 0 mm.The nominal length of the pipe with socket for solvent cementing/grooved socket shall be as given in Fig. 1.)	-	0	INCLUDED IN 7.1
Cl.7.3.1(Minimum wall thickness of socket on pipes shall be as given in Table 2 read with Fig. 2 and Fig. 3.)	-	0	INCLUDED IN 7.1
Cl.7.3.2(Dimensions of sockets for solvent cementing and grooved sockets of pipes shall be as given in Tables 3 and 4 respectively, read with Fig. 2 and 3.)	-	0	INCLUDED IN 7.1
Cl.8.1(The internal and external surface of the pipes shall be smooth and clean, and free from grooving and other defects. The end shall be clearly cut and shall be square with the axis of the pipe. The end may be chamfered on the plain side.)	-	500	NIL
Cl.8.2(When tested by the method described in IS 12235 (Part 5), a length of pipe sample of 200 ± 20 mm shall not alter in length by more than 5 percent. In the case of socket ended pipes, this test shall be carried out on the plain portion of pipe taken at least 100 mm away from the root of the socket.)	-	1200	INCLUDES SPECIMEN CHARGE
Cl8.3(This test shall be carried out for socket end pipes only. When tested by the method described in IS 12235 (Part 6), the test specimens shall not show blisters, excessive delamination or cracking or signs of weld line splitting.)	-	700	NIL
Cl.8.4(When determined in accordance with IS 12235 (Part 2), the vicat softening temperature of the specimen shall not be less than 79°C.)	-	1100	NIL
Cl.8.5(After the required period of exposure, the tensile strengths of two samples when tested as per IS 12235 (Part 13) shall not show difference of more than 20 percent of their initial tensile strengths)	-	4850	INCLUDES EXPOSURE TO SUNLIGHT
Cl. 9, IS 12235 Part 7(Resistance to Sulphuric Acid)	-	2500	INCLUDES SPECIMEN CHARGE
Cl.10.1(When tested by method prescribed in IS 12235 (Part 9),the pipe shall have a true impact rate of not more than 10 percent. Mass of striker and height of fall shall be as per Annex A.)	-	1600	INCLUDES SPECIMEN CHARGE
Cl.10.2(When determined in accordance with the method described in IS 12235 (Part 13), the tensile strength at break shall not be less than 45 MPa.)	-	1800	INCLUDES SPECIMEN CHARGE
Cl.10.3(The axial shrinkage shall not exceed 2 percent when determined in accordance with Annex B.)	-	850	NIL
Cl.11.(Jointing of solvent cementing joints is to be carried out using solvent conforming to IS 14182. Apply a pressure of 0.05 MPa for a period of 15 min and there should be no leakage at any joint.)	-	1000	NIL
Cl. 12, IS 12235 Part 11(Resistance to Di-Chloro-Methane )	-	1000	NIL

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 12818 (2010)

Unplasticized polyvinyl chloride (Pvc - U) screen and casing pipes for bore/tubewells - Specification (Second Revision)

SIZE 35MM - 400 MM

14550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.6(Vicat Softening Temperature IS 12235 (Part 2).)	-	1100	NIL
9.5(Tensile Strength IS 12235(Part 13))	-	1800	INCLUDES SPECIMEN CHARGE
9.4 and Table 14(Resistance to External Blows at 0 ?C IS 12235 (Part 9))	-	1500	INCLUDES SPECIMEN CHARGE
9.3(Density IS 12235 (Part 14))	-	700	NIL
9.1( Visual Appearance)	-	500	NIL
8.4.1 and Table 13 Fig 3B & 4B(Dimensions of sealing elements)	-	500	NIL
7.5 and Table 10 Fig 2A & 2B(Approximate Free Passage Area, in Percent (Mean Value) for Width of Slot (w))	-	1500	NIL
7.5 and Table 10 Fig 2A & 2B(Minimum number of slots on the circumference of the cross-section.)	-	0	NIL
7.5 and Table 10 Fig 2A & 2B(Summation of slot lengths over internal circumference of the cross- section.)	-	0	NIL
9.2(Internal Diameter)	-	500	NIL
8.4(Sealing rings - Hardness)	-	500	NIL
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	500	NIL
8.1 to 8.3 and Table 11 &12 Fig 3A & 4A(THREADING OF SCREEN ANDCASING PIPES. IS 554.)	-	0	INCLUDED IN 8.1&8.3
7.4 Table 8 & 9 Fig 1(Segmental length, l5)	-	0	NIL
7.4 Table 8 & 9 Fig 1(Segmental length, l4)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.4 Table 8 & 9 Fig 1(Segmental length, l3)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.4 Table 8 & 9 Fig 1(Effective length, l2)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.3.2(Rib height)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.3.1(No.of Ribs)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Max)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Wall thickness, Min)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter over Connection)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point, Max)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Outer Diameter at any point , Min)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe , Max)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Mean Outer Diameter of Pipe, Min)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(Nominal Diameter)	-	0	INCLUDED IN SEGMENTAL LENGTH L5
7.2 and Table 5, 6 & 7 Fig 1B(DIMENSIONS - Casing Pipes)	-	0	NIL
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Wall thickness)	-	0	INCLUDED IN DIMENSION 7.2
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter over Connection)	-	0	INCLUDED IN DIMENSION 7.2
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Outer Diameter at any point )	-	0	INCLUDED IN DIMENSION 7.2
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Mean Outer Diameter of Pipe)	-	0	INCLUDED IN DIMENSION 7.2
7.1 and Table 1, 2, 3, & 4 Fig 1A & 1B(Nominal Diameter)	-	0	INCLUDED IN DIMENSION 7.2
4.1.2 (Ref. Cl 11 of IS 4669)(Composition -Sulphated ash content )	-	1200	NIL
4.1.2 (Ref. Cl 5.1. of IS 4669)(Composition - Loss on heating )	-	0	NIL
4.1.1 (Ref. 3.4.1. of IS 10151)(Composition - The monomer content (VCM content) in the resin - Annex A ofIS 10151)	-	2750	NIL
5(COLOUR)	-	500	NIL
4.1.2(K-Value as per IS-4669)	-	1000	NIL

Complete

06 Jun, 2024

IS 12786 (2024)

Irrigation equipment - Polyethylene pipes for irrigation laterals - Specification (first revision)

SIZE 12 MM, 16 MM, 20 MM, 25MM, 32MM. CLASS 1,2, & 3

14875 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.c.i (Density)	-	1325	FOR RAW MATERIAL
4.1.c.ii (Toluene extract - Annex A)	-	1100	FOR RAW MATERIAL
4.1.c.iii (Volatile matter - Annex B )	-	700	FOR RAW MATERIAL
4.1.c & 4.2.a (Carbon Black content - IS 2530 : 1963)	-	925	FOR RAW MATERIAL
4.2.b (The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	FOR RAW MATERIAL
4.3(Addition of not more than 10 percent of the manufactures own rework material produced during the manufacture and works testing of pipe complying with this standard is permitted. No other rework material shall be used)	-	0	NIL
7.3(Tensile Test)	-	1800	NIL
7.3(Elongation at Break)	-	0	CHARGES INCLUDED IN TENSILE
7.4(SusceptibiIity to Environmental Stress Cracking)	-	1200	NIL
Cl-4.1(Material)	-	0	NIL
Cl-4.2(Carbon content of finished PE lateral pipe)	-	925	NIL
Cl-5.1(Dimensions of pipes and wall thicknesses)	-	500	NIL
Cl-6.0(Visual Appearance)	-	500	NIL
Cl-7.1(Hydraulic Characteristics- Internal pressure creep rupture test)	-	3000	NIL
Cl-7.1(Hydraulic Characteristics- quality acceptance test)	-	1000	NIL
Cl-7.2(Reversion Test)	-	1200	NIL
Cl-7.3(Tensile Test)	-	0	NIL
Cl-7.4(Susceptibility to Environmental Stress Cracking)	-	0	NIL
5.1 & Table 1(Dimensions of Pipes - Outside diameters)	-	0	NIL
5.1 & Table 1(Dimensions of Pipes - Wall thickness)	-	0	NIL
6(Visual Appearance)	-	0	NIL

Complete

06 Jun, 2024

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

CAPACITY 200-20000L

13700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	900	NIL
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	5000	INCLUDES ALL DIMENSIONAL CHARGES
4.2.3(Carbon Dispersion Test)	-	0	NIL
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	INCLUDES ALL DIMENSIONAL CHARGES
6.1(Finish)	-	500	NIL
7.1.1(Resistance to Deformation)	-	700	NIL
7.1.2(Resistance to Deformation)	-	0	NIL
7.2(Resistance to Impact)	-	1000	NIL
7.4(Tensile Strength)	-	1800	INCLUDES SPECIMEN CHARGE
7.5(Flexural Modulus)	-	1600	INCLUDES SPECIMEN CHARGE
7.6(overall Migration)	-	2200	INCLUDES SPECIMEN CHARGE

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 2 (2009)

Fabricated pvc - U fittings for potable water supplies - Specification: Part 2 specific requirements for sockets (Second Revision)

SIZE 20MM TO 630MM, CLASS 1-6

6750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (First Extraction))	-	3000	NIL
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-4)(Effect on water: Lead (Third Extraction))	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
10.3 of IS 4985 & Cl. 3.1 of IS 12235(P-10)(Effect on water:Dialkyl tin C4 and higher homologues measured as tin (third extraction))	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Cadmium (all three extracts))	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-4)(Effect on water: Mercury (all three extracts))	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
10.3 of IS 4985 & Cl. 3.2 of IS 12235(P-10)(Other toxic substances such as 'di-n-octyl-tin- s-s bis iso-octyl mercapto acetate' and 'butyl stearate' (third extraction))	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
10.7 of IS 4985(Sulphated Ash content, Annex-B of IS 4985)	-	1200	NIL
3.2.1, Table-1, Fig-1(B)	-	500	NIL
3.2.1, Table-1, Fig-1(Minimum wall thickness for working pressure)	-	0	CHARGES INCLUDED IN DIMENSION
Clause 3.2.2, and Fig. 2.(B)	-	0	CHARGES INCLUDED IN DIMENSION
3.2.2, and Fig. 2(Dimensions of Socket for Elastomeric Sealing Ring Joint)	-	0	CHARGES INCLUDED IN DIMENSION
3.1(General)	-	2050	For Opacity Test = 700 Short Term Hydraulic Test = 1350

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 10124 : Part 1 (2009)

Fabricated PVC-U Fittings for Potable Water Supplies - Specification Part 1 General Requirements (Second Revision)

SIZE 20 TO 630MM

6650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Material)	-	1100	FOR PVC RESIN K-Value
5.1 Table-1 Fig.1(Dimension of Socket length)	-	500	NIL
5.1.2 Table-1(Dimensions of mean inside diameter at mid-point of socket depth)	-	0	CHARGES INCLUDED IN DIMENSION
5.1.3 (Out of Roundness Tolerance of Socket Inside Diameter)	-	0	CHARGES INCLUDED IN DIMENSION
5.2 Table-2 Fig.2(Dimensions of socket for elastomeric sealing ring)	-	0	CHARGES INCLUDED IN DIMENSION
6.1(Opacity test in accordance with IS 12235 (Part 3))	-	700	NIL
6.2(Short Term Hydraulic Test in accordance with Annex A)	-	1350	NIL
8(Marking)	-	0	NIL
6.3(Effect on water test)	-	3000	Nil

Complete

06 Jun, 2024

0.0

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

SIZE 16-315 MM

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	500	NIL
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	3000	NIL
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Dialkyl tin C4 and higher homologues measured as tin (third extraction) - Appendix C)	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 7834 : Part 1 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 1 General requirements

SIZE 16-315MM

6250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4(Minimum Thickness)	-	500	NIL
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Minimum Socket Length)	-	0	CHARGES INCLUDED IN THICKNESS
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Mean Socket Internal Diameter at Mid-Point of Socket Length)	-	0	CHARGES INCLUDED IN THICKNESS
Cl. 5.1.1, 5.1.2, Table 1, Fig 1(Out-of-roundness tolerances of socket inside diameter)	-	0	CHARGES INCLUDED IN THICKNESS
Cl. 6.1(Stress Relief Test- Appendix A)	-	700	NIL
Cl. 6.3(Effect on Water[(Lead ( first extraction )]- Appendix C)	-	3000	NIL
Cl. 6.3(Effect on Water[(Lead ( third extraction )]- Appendix C)	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
Cl. 6.3(Effect on Water [Dialkyl tin C4, and higher homologues, measured as tin ( third extraction )]- Appendix C)	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
Cl. 6.3(Effect on Water [Other toxic substances ( third extraction )]- Appendix C)	-	0	CHARGES INCLUDED IN LEAD 1ST EXTRACTION
Cl. 6.4(Short-Term Hydraulic Test- Appendix D)	-	1350	NIL
Cl. 6.2(Opacity- Appendix B)	-	700	NIL

Complete

06 Jun, 2024

Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

NATURAL & BLACK COMPOUNDED , TYPE 1 TO 4

22675 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	500	NIL
5.1.2(Film Form)	-	0	NIL
5.1.3(Odour)	-	0	NIL
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	700	NIL
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	NIL
5.1.6a(Carbon Black Content, Annex-A)	-	925	NIL
5.1.6b(Ash Content, Annex-A)	-	1200	NIL
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	NIL
5.2.2(Tolerance on Thickness, Annex-A)	-	500	CHARGE FOR DIMENSION
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1800	NIL
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1300	NIL
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	NIL
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	850	NIL
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1600	NIL
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1100	NIL
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1300	NIL
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1300	NIL
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	0	NIL
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	0	NIL
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1800	NIL
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1800	NIL
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
8.1, Table 3(Tear resistance , Annex B)	-	0	NIL
8.1, Table 3(Puncture resistance , Annex C)	-	0	NIL
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	NIL
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	NIL
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	0	CHARGES INCLUDED IN TENSILE STRENGTH
9.1, Table 4(Tear resistance , Annex B)	-	0	NIL
9.1, Table 4(Puncture resistance , Annex C)	-	0	NIL

Complete

06 Jun, 2024

Included w.e.f. 02.08.2018. Testing charges has been fixed for two years w.e.f. 30-05-2019 to 29-05-2021.

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

SIZE: 20MM TO 630MM, CLASS: 1 TO 6

27450 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
11.2(Resistance to External Blows at 0°C)	-	1500	FOR ELASTOMERIC SEALING RING SOCKETS
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	FOR ELASTOMERIC SEALING RING SOCKETS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	FOR ELASTOMERIC SEALING RING SOCKETS
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000	FOR ELASTOMERIC SEALING RING SOCKETS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	FOR ELASTOMERIC SEALING RING SOCKETS
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	5000	FOR ELASTOMERIC SEALING RING SOCKETS
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	700	FOR ELASTOMERIC SEALING RING SOCKETS
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	FOR ELASTOMERIC SEALING RING SOCKETS
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1200	FOR ELASTOMERIC SEALING RING SOCKETS
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	700	FOR ELASTOMERIC SEALING RING SOCKETS
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	500	FOR ELASTOMERIC SEALING RING SOCKETS
9.1(PIPE ENDS)	-	500	FOR ELASTOMERIC SEALING RING SOCKETS CHARGE IS INCLUDED IN VISUAL APPEARANCE
7.2.1.2-Table 4(DIMENSIONS-Sockets for elastomeric sealing ring joints-Socket inner Diameter)	-	500	FOR ELASTOMERIC SEALING RING SOCKETS
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	500	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Maximum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	500	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	FOR ELASTOMERIC SEALING RING SOCKETS RS. 500 INCLUDES ALL DIMENSIONAL PARAMETERS
Clause 10.7(Sulphated Ash Content)	-	1200	FOR ELASTOMERIC SEALING RING SOCKETS
11.2(Resistance to External Blows at 0°C)	-	0	Resistance to External Blows at 0°C
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	0	MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)
10.1.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	0	Vicat Softening Temperature
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	0	Reversion Test
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	0	Opacity
10.1(PHYSICAL AND CHEMICAL CHARACTERISTICS-Visual Appearance)	-	0	Visual Appearance
9.1(PIPE ENDS)	-	0	PIPE ENDS
7.2.1.2(a)-Table 5(DIMENSIONS-Sockets for elastomeric sealing ring joints-Minimum depth of engagement)	-	0	Minimum depth of engagement
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	0	Minimum Length
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	0	Diameter at mid point of the socket length (Minimum)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	0	PIPE-Thickness(Minimum)
7.1.2.1(DIMENSIONS-PIPE-Thickness(Maximum))	-	0	-PIPE-Thickness(Maximum)
7.1.1.2(DIMENSIONS-PIPE-Ovality (Maximum))	-	0	Ovality (Maximum)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	0	O.D. at any Point (Minimum)
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Maximum))	-	0	O.D. at any Point (Maximum)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	0	Mean O.D. (Minimum)
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Mamimum))	-	0	Mean O.D. (Mamimum)
10.7(Sulphated Ash Content)	-	0	Sulphated Ash Content
10.1(Colour)	-	0	Colour
6.1.2(PVC Resin)	-	0	Nil

Complete

06 Jun, 2024

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

SDR 41 to 6, DN 16 to 1200 mm, PE 63/80/100, PN 2 to20

55650 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.10(Slow Crack Growth Rate)	-	6000	INCLUDES SPECIMEN CHARGE
8.9 table-6(Elongation at Break)	-	1800	INCLUDES SPECIMEN CHARGE
8.8(Tensile Strength for Butt-fusion)	-	1800	INCLUDES SPECIMEN CHARGE
8.7(Density)	-	700	NIL
8.5 (Oxidation Induction Time)	-	2200	NIL
8.4( Melt Flow Rate)	-	1100	NIL
8.2(Longitudinal Reversion Test)	-	1200	INCLUDES SPECIMEN CHARGE
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	NIL
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21900	INCLUDES ALL TESTS
7.4.1.2(Ovality)	-	0	INCLUDES IN DIMENSION
7.4 table -3 & 4(6.1 Dimensions)	-	500	INCLUDES ALL DIMENSIONAL MEASUREMENTS
7.2(Length)	-	0	INCLUDES IN DIMENSION
6.2.1(6.1.1 Identification Stripes)	-	500	NIL
8.6(Overall migration)	-	2200	INCLUDES SPECIMEN CHARGES
8.3(Carbon black)	-	1625	INCLUDES CARBON BLACK DISPERSION TEST
5.3(e)(Carbon Black Master Batch)	-	5450	INCLUDES ALL TEST FOR CARBON BLACK POWDER
5.3(d)(Carbon Black Master Batch)	-	950	NIL
5.3(c)(Carbon Black Master Batch)	-	925	NIL
5.2(Polyethylene Resin)	-	5200	INCLUDES ALL TEST CHARGES FOR RAW MATERIAL

Complete

06 Jun, 2024

IS 16709 (2017)

Textiles - Polypropylene (PP) woven, laminated, block bottom valve sacks for packaging of 50 kg cement - Specification

PP Woven laminated Fabric, 50kg Capacity

22250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Sack Length)	-	500	Nil
4.1.2(Sack Width)	-	0	Included in Sack Length Dimension
4.1.3(Top Closure Width and Bottom Closure Width)	-	500	Nil
4.1.4(Patch Length)	-	500	Nil
4.1.5(Patch Height)	-	0	Included in Patch Length Dimension
4.1.6(Length of Valve)	-	500	Nil
4.1.7(Width of Valve Sleeve)	-	0	Included in Length of Valve
4.1.8(Length of Valve Sleeve)	-	0	Included in Length of Valve
5.1(Raw Material)	-	1050	Nil
5.2(Fabric)	-	500	Nil
5.2(Tape density and width)	-	7350	Nil
5.4(Lamination for PP)	-	2550	Nil
5.4(Lamination for LDPE)	-	0	Nil
6.1(Mass of Bale)	-	500	Nil
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	2700	Nil
6.2.2(Weld Strength of Top and Bottom Closures)	-	0	Nil
6.3(Drop Impact Testing of Filled Sacks)	-	1100	Nil
6.4(Ash Content)	-	1200	Nil
8(Atomspheric Conditions for Conditioning and Testing)	-	700	Nil
Cl-5.6(Capacity)	-	500	Nil
Cl- 6.6, Table.-1 (ii)(Ends per dm)	-	500	Nil
Cl-6.6, Table-1 (iii)(Picks per dm)	-	500	Nil
Cl.6.6, Table-1 (vii)(Elongation at break of fabric)	-	1100	Nil

Complete

06 Jun, 2024

IS 15450 (2022)

Polyethylene-aluminium-polyethylene composite pressure pipes for hot and cold water supplies Specifications first revision of IS 15450

PE-AL-PE 12 to 75mm

46275 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(MATERIALS)	-	5625	-
6(PRESSURE RATING)	-	500	-
7(NOMINAL DIAMETERS)	-	500	-
8(COLOUR)	-	500	-
9(DIMENSIONS OF PIPE)	-	500	-
10(VISUAL APPEARANCE)	-	500	-
11.1(Density (Method of test as per Table 3))	-	700	-
11.2(Melt Flow Rate (Method of test as per Table 3))	-	1100	-
11.3(Overall Migration)	-	2200	-
11.4(Thermal Stability to Oxidation (Method of test as per Table 3))	-	2200	-
11.5(Carbon Black Content and Dispersion (Method of test as per Table 3))	-	925	-
11.6(Pigment Dispersion (For Coloured Pipes) (Method of test as per Table 3))	-	700	-
11.8(Adhesion Test)	-	1600	-
11.7(Resistance to Weathering)	-	16500	-
11.9(Apparent Tensile Strength of Pipe)	-	1800	-
11.10(Minimum Burst Pressure)	-	1000	-
11.11(Hydraulic Characteristics)	-	5300	-
Table 3(Anti-oxidant (as per IS 2530))	-	500	-
14(MARKING)	-	500	-
5.1(MATERIALS)	-	0	-
5.2.1(MATERIALS)	-	0	-
5.2.1.1(The other constituents)	-	925	-
5.3.1(UV Stabilizer)	-	0	-
5.3.2(UV Stabilizer)	-	0	-
11.11.1(Short Term Hydrostatic Tests)	-	0	-
11.11.12(Long Term Hydrostatic Test)	-	0	-
5.4(Aluminium)	-	0	-
5.5(REWORK Material)	-	0	-
6(PRESSURE RATING)	-	0	-
12.1(Type Test)	-	2200	-
7(NOMINAL DIAMETERS)	-	0	-
8(COLOUR)	-	0	-
9.1(DIMENSIONS OF PIPE)	-	0	-
9.2.1(Method of Measurements)	-	0	-
9.3(Length of Straight Pipe)	-	0	-
9.4(Coiling)	-	0	-
10(VISUAL APPEARANCE)	-	0	-
11.1(Density)	-	0	-
11.3(Melt Flow Rate)	-	0	-
11.4(Thermal Stability to Oxidation)	-	0	-
11.5(Carbon Black Content and Dispersion)	-	0	-
11.6(Pigment Dispersion (For Coloured Pipes))	-	0	-
11.7(Resistance to Weathering)	-	0	-
11.8(Adhesion Test)	-	0	-
11.9(Apparent Tensile Strength of Pipe)	-	0	-
11.1(Minimum Burst Pressure)	-	0	-
11.3(Overall Migration)	-	0	-

Complete

06 Jun, 2024

IS 14333 (2022)

Polyethylene Pipes for Sewerage and Industrial Chemicals and Effluent ï¿½ Specification (First Revision)

GRADE PE 63,80,100, PN 2.5,4,6,10,12.5 SIZE 63-1000MM

53975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1,T2("Base Density (At 27°C Temp.)-IS 7328:2020 ")	-	1325	-
5.2.1,T2(Melt Flow Rate (At 190°C /5kg)-IS 2530:1963)	-	1100	-
5.2.1,T2(Thermal Stability(Oxidation Induction Time)-IS 4984:2016(Annexure-B))	-	2200	-
5.2.1,T2("Volatile Matter- IS 4984:2016 (Annexure-C)")	-	700	-
5.3(Ash content- Any Method)	-	1200	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 content")	-	925	-
6.2(Colour- IS 14333-2022)	-	500	-
7.1(Visual Appearance- IS 14333-2022)	-	500	-
7.2(Length- IS 14333-2022)	-	500	-
7.4,T3 of IS 4984(Outside Diameter-IS 4984-2016)	-	500	-
7.4,T4 of IS 4984(wall Thickness-IS 4984-2016)	-	0	-
7.4,T3 of IS 4984(Ovality-IS 4984-2016)	-	0	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 27 oC , Test Period - 100 hrs.-IS 4984-2016 (Annexure-E))	-	4000	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 165 hrs.-IS 4984-2016 (Annexure-E))	-	4800	-
8.1.1, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 1000 hrs.-IS 4984-2016 (Annexure-E))	-	11000	-
8.1.2, T4(Internal Pressure creep Rupture test, Temperature - 80 oC , Test Period - 48 hrs.-IS 4984-2016 (Annexure-E))	-	1600	-
8.2("Longitudinal Reversion Test - IS 4984-2016 (Annexure-F)")	-	1200	-
8.3(Carbon black content- IS 2530-1963)	-	925	-
8.3(Carbon black content Dispersion- IS 2530-1963)	-	700	-
8.4(Melt Flow rate(Temperature - 190oC,Mass 5kg)-IS 2530-1963)	-	1100	-
8.5(Oxidation Induction Time -IS 4984:2016(Annexure-B))	-	2200	-
8.6(Density-IS 7328:2020)	-	700	-
8.7("Tensile Strength for Butt Fusion - IS 4984-2016 (Annexure-G)")	-	1800	-
8.8,T5("Tensile - IS 4984-2016 (Annexure-H)")	-	1600	-
8.8,T5("Elongation -IS 4984-2016 (Annexure-H)")	-	0	-
8.9(Slow Crack Growth Rate{Internal Pressure creep Rupture test, Temperature - 80±1 oC , Test Pressure – 0.80MPa, Test Period - 500 hrs.-IS 4984-2016 (Annexure-E &J))	-	6000	-
5.2.1,T2("Water Content-IS 4984:2016 (Annexure-D)")	-	700	-
5.3(Density of Higher olefin - IS 7328:2020)	-	700	-
5.2.1.1, T2(Compound Toluene extract - Any Method)	-	900	-
5.2.1.1, T2(Compound carbon black particle size- Any Method)	-	3000	-
5.2.1.1, T2(Compound Density-IS 7328:2020)	-	0	-
5.2.1.1, T2(Compound ash content - Any Method)	-	0	-
5.2.1.1, T2("Compound carbon black -IS 2530:1963 dispersion")	-	0	-
5.3(Loading of Carbon Black - IS 2530:1963)	-	0	-
5.3("Maximum volatile matter -IS 4984:2016 (Annexure-C)")	-	0	-
5.4(Antioxidant - Any Method)	-	0	-
6(Pipe Description - IS 14333-2022)	-	0	-
7.3(Coiling- IS 14333-2022)	-	0	-
5.2.1.1, T2(Compound maximum volatile matter -IS 4984:2016 (Annexure-C))	-	0	-
5.3(Olefin Constituents- 14333-2022)	-	0	-
5.3(Toluene extract - Any Method)	-	0	-
5.3(Carbon black particle size - Any Method)	-	0	-

Complete

06 Jun, 2024

IS 14885 (2022)

Polyethylene Pipes for the Supply of Gaseous Fuels ï¿½ Specification (First Revision)

GRADE PE 80 & 100, SIZE 16-630, SDR 17,13.6,11,9

520700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2(Grade of material)	-	1100	NIL
4.3(Nominal Diameter)	-	500	NIL
4.4(Colour)	-	500	NIL
5.3(Anti-oxidant)	-	700	NIL
6.1(Outside Diameter)	-	0	INCLUDED IN DIMENSION
6.1(Out of Roundness (Ovality))	-	0	NIL
7(Finish)	-	500	NIL
6.2(Wall Thickness)	-	500	NIL
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	5300	NIL
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	4500	NIL
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	11000	NIL
8.2(Reversion Test)	-	700	NIL
8.3(Density)	-	700	NIL
8.6(Thermal Stability (Oxidation Induction Time))	-	2200	NIL
8.7(Volatile Matter Content)	-	700	NIL
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	1800	NIL
6.4(Length of Pipe)	-	500	NIL
8.4(Melt Flow Rate (MFR))	-	1100	NIL
8.5(Pigment Dispersion)	-	700	NIL
8.10(Slow Crack Growth Rate Test)	-	10800	NIL
10(Marking)	-	500	NIL
5.6(Resistance to Weathering)	-	36000	NIL
8.11(Squeeze-off)	-	1300	NIL
4.2(Grade of material)	-	0	NIL
4.3(Nominal Diameter)	-	0	NIL
4.4(Colour)	-	0	NIL
5.3(Anti-oxidant)	-	0	NIL
6.1(Outside Diameter)	-	0	NIL
6.1(Out of Roundness (Ovality))	-	0	NIL
7(Finish)	-	0	NIL
6.2(Wall Thickness)	-	0	NIL
8.1(Internal pressure creep rupture test for plain at 80 deg. C for 165h)	-	0	NIL
8.1(Internal pressure creep rupture test for plain pipes at 20 deg. C for 100h)	-	0	NIL
8.1(Internal pressure creep rupture test for plain pipes at 80 deg. C for 1000 h)	-	0	NIL
8.2(Reversion Test)	-	0	NIL
8.3(Density)	-	0	NIL
8.6(Thermal Stability (Oxidation Induction Time))	-	0	NIL
8.7(Volatile Matter Content)	-	0	NIL
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	NIL
6.4(Length of Pipe)	-	0	NIL
8.4(Melt Flow Rate (MFR))	-	0	NIL
8.5(Pigment Dispersion)	-	0	NIL
8.10(Slow Crack Growth Rate Test)	-	0	NIL
5.6(Resistance to Weathering)	-	0	NIL
8.11(Squeeze-off)	-	0	NIL
5.1, 5.7 Table 2(i) Conventional density (of base polymer))	-	700	NIL
5.1, 5.7 Table 2(ii) Melt flow rate (MFR))	-	1100	NIL
5.1, 5.7 Table 2(iii) Thermal stability (oxidation induction time))	-	2200	NIL
5.1, 5.7 Table 2(iv) Volatile content)	-	700	NIL
5.1, 5.7 Table 2(v) Water content1))	-	700	NIL
5.1, 5.7 Table 2(vi) Pigment dispersion)	-	700	NIL
5.1, 5.7 Table 3(iv) Resistance to slow crack growth rate)	-	0	NIL
5.5(Effect of Gas condensate on the Hydrostatic strength)	-	5000	NIL
5.7(PE Compound Quality Evaluation)	-	400000	NIL
5.1(Polyethylene compound)	-	5000	NIL
5.4(U-V stabilizer)	-	2500	NIL
8.9(Resistance to Weathering)	-	15500	NIL
10(Marking)	-	0	NIL
5.3(Anti-Oxidant)	-	0	NIL
5.4(U.V. Stabilizer)	-	0	NIL
5.5(Effects of Gas Condensate on the Hydrostatic Strength)	-	0	NIL
5.6(ii) Hydraulic characteristics)	-	0	NIL
5.6(iii) Thermal stability (Oxidation induction time))	-	0	NIL
6(Dimensions of pipes)	-	0	NIL
7(Finish)	-	0	NIL
8.1(Hydraulic Characteristics)	-	0	NIL
8.2(Reversion test)	-	0	NIL
8.3(Density)	-	0	NIL
8.4(Melt Flow Rate)	-	0	NIL
8.5(Pigment Dispersion)	-	0	NIL
8.6(Thermal Stability (Oxidation Induction Time))	-	0	NIL
8.7(Volatile Matter Content)	-	0	NIL
8.9(Resistance to Weathering)	-	0	NIL
8.8(Tensile Properties (Tensile Yield Strength and Elongation at Break))	-	0	NIL
8.10(Slow Crack Growth Rate Test)	-	0	NIL
8.11(Squeeze-of)	-	0	NIL

Complete

06 Jun, 2024

Bureau of Indian Standards

The National Standards Body of India

CIPET, Vijayawada

SY NO. 377, SURAMPALLY X ROAD, GANNAVARAM MANDAL, VIJAYAWADA, VIJAYAWADA, Krishna, Andhra Pradesh, 521212

7077573905 vijayawada@cipet.gov.in

Scope List