BIS - LIMS (Laboratory Information Management System)

CIPET: CSTS, CHHATRAPATI SAMBHAJINAGAR

Plot No. J-3/2, MIDC Industrial Area, Chikalthana, Jalgaon Road, Chhatrapati Sambhajinagar - 431 006, Chhatrapati Sambhajinagar, Aurangabad, Maharashtra, 431006

8602677054 aurangabad@cipet.gov.in

Scope List

Reset

37 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

TYPE 1 TO 4

24625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Appearance)	-	500	Appearance
5.1.2(Film Form)	-	0	Test charges included in Clause 5.1.1
5.1.3(Odour)	-	0	Test charges included in Clause 5.1.1
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	700	Density, Cl.5 of IS 13360(Part-3/Section-1)
5.1.5(Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1))	-	1100	Melt Flow Index. Cl 6, 7 of IS 13360(Part-4/Section-1)
5.1.6a(Carbon Black Content, Annex-A)	-	925	Carbon Black Content, Annex-A
5.1.6b(Ash Content, Annex-A)	-	1200	Ash Content, Annex-A
5.1.6c(Carbon Black Dispersion, Cl.16 of IS 2530)	-	700	Carbon Black Dispersion, Cl.16 of IS 2530
5.2.2(Tolerance on Thickness, Annex-A)	-	500	Tolerance on Thickness, Annex-A
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1800	Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1) (1300+500)
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1300	Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3) (1300)
6.1, Table 1(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Ageing test at (70-1)c for 7 days , cl 4 IS 7016
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	1300	Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1)
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	1300	Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3)
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	850	Dartimpact strength Method B of IS 13360 (Part-5/sec-6)
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1600	Tear resistence. A) Machine direction Annex B (1100+500)
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1100	Tear resistence. B) Transverse direction
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1300	Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1)
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1300	Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3)
7.1. Table 2(Ageing test at (70-1)c for 7 days , cl 4 IS 7016 )	-	4200	Ageing test at (70-1)c for 7 days , cl 4 IS 7016
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	1300	Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1)
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	1300	Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3)
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	850	Dart impact strenght , Method A of IS 3360 (Part-5/sec-6)
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
8.1, Table 3(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
8.1, Table 3(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
8.1, Table 3(Tear resistance , Annex B)	-	1100	Tear resistance , Annex B
8.1, Table 3(Puncture resistance , Annex C)	-	1100	Puncture resistance , Annex C
9.1, Table 4(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
9.1, Table 4(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
9.1, Table 4(Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	Tensile properties ,C) Yield elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
9.1, Table 4(Tear resistance , Annex B)	-	1100	Tear resistance , Annex B
9.1, Table 4(Puncture resistance , Annex C)	-	1100	Puncture resistance , Annex C
5.1.1(Appearance)	-	300	Appearance
5.1.4(Density, Cl.5 of IS 13360(Part-3/Section-1))	-	500	Density, Cl.5 of IS 13360(Part-3/Section-1)
5.1.6a(Carbon Black Content, Annex-A)	-	700	Carbon Black Content, Annex-A
5.1.6b(Ash Content, Annex-A)	-	950	Ash Content, Annex-A
5.2.2(Tolerance on Thickness, Annex-A)	-	250	Tolerance on Thickness, Annex-A
6.1, Table 1(Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1))	-	1100	Tensile strength at break. A) Machine Direction. IS 13360 (Part 5/Sec 1)
6.1, Table 1(Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3))	-	1100	Tensile strength at break. B) Transverse Direction. IS 13360 (Part 5/Sec 3)
6.1, Table 1(Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1) )	-	1100	Elongation at break ,A) Machine direction .IS 13360(Part-5/sec-1)
6.1, Table 1(Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3) )	-	1100	Elongation at break ,B) Cross-machine direction..IS 13360(Part-5/sec-3)
6.1, Table 1(Dartimpact strength Method B of IS 13360 (Part-5/sec-6) )	-	1000	Dartimpact strength Method B of IS 13360 (Part-5/sec-6)
6.1, Table 1(Tear resistence. A) Machine direction Annex B)	-	1000	Tear resistence. A) Machine direction Annex B
6.1, Table 1(Tear resistence. B) Transverse direction )	-	1000	Tear resistence. B) Transverse direction
7.1. Table 2(Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1) )	-	1100	Tensile strength at break A) Machine direction IS 13360 (Part-5/sec-1)
7.1. Table 2(Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3) )	-	1100	Tensile strength at break,B) Crosse machine direction IS 13360 (Part-5/sec-3)
7.1. Table 2(Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1) )	-	1100	Elongation at break , A) Machine direction IS 13360 (Part-5/sec-3) IS 13360 (Part-5/sec-1)
7.1. Table 2(Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3) )	-	1100	Elongation at break , A) Transverse direction IS 13360 (Part-5/sec-3)
7.1. Table 2(Dart impact strenght , Method A of IS 3360 (Part-5/sec-6) )	-	1000	Dart impact strenght , Method A of IS 3360 (Part-5/sec-6)
8.1, Table 3(Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	Tensile properties ,A) Yield strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
8.1, Table 3(Tensile properties , B) Break strenght . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1300	-
8.1, Table 3(Tear resistance , Annex B)	-	1000	Tear resistance , Annex B
9.1, Table 4(Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do)	-	1100	Tensile properties ,D) Break elongation . IS 3360 (Part-5/sec-1) and IS 3360 (Part-5/sec-3) Test condition- specimen type 5 and test speed 51 mm/min do
9.1, Table 4(Tear resistance , Annex B)	-	1000	Tear resistance , Annex B
Clause 9.1 (Table 4)(Break Elongation)	-	1300	-
Clause 9.1 (Table 4)(Yield Elonation)	-	0	-
Clause 9.1 (Table 4)(Break strength)	-	0	-
Clause 9.1 (Table 4)(Yield strength)	-	0	-
Clause 8.1(Table 3)(Break Elongation)	-	0	-
Clause 8.1(Table 3)(Break strength)	-	0	-
Clause 7.1(Table 2)(Dart Impact Strength)	-	0	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1300	-
Clause 7.1(Table 2)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1300	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Transverse Direction))	-	1300	-
Clause 6.1(Table 1)(Decrease in Tensile Strength after Ageing(Machine Direction))	-	1300	-
Clause 5.2.3(Tolerance on Width)	-	500	-
Cl.5.1.6(a)(Carbon Black Content)	-	925	-
Cl.5.1.6(b)(Ash content)	-	1200	-
Cl.5.1.6(c)(Dispersion of Carbon Black)	-	700	-
5.2.1.1(Nominal Thickness)	-	500	-
5.2.1.2(Nominal width)	-	500	-

31 Dec, 2026

-
-

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

23325 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Normal use)	-	500	-
4.2(Reasonably foreseeable abuse)	-	500	-
4.3.1(Material quality)	-	500	-
4.3.2(Expanding materials)	-	1200	500+700
4.4.1(For children under 36 months)	-	500	-
4.4.2(For children 36 months and over but under 72 months)	-	500	-
4.5.1.2(Squeeze toys, rattles, and certain other toys and components of toys)	-	500	-
4.5.1.3(Other toys or components of toys with nearly spherical, hemispherical, circular flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children under 18 months)	-	500	-
4.5.1.4(Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical, or dome-shaped ends intended for children 18 months and over but under 48 months)	-	500	-
4.5.2(Small balls)	-	500	-
4.5.3(Pompoms)	-	500	-
4.5.4(Pre-school playfigures)	-	500	-
4.5.5(Toy pacifiers)	-	500	-
4.5.6(Balloons)	-	500	-
4.5.7(Marbles)	-	500	-
4.5.8(Hemisphericshaped toys)	-	500	-
4.6.1(Accessible sharp edges of glass or metal)	-	500	-
4.6.2(Functional sharp edges)	-	500	-
4.6.3(Edges on metal toys)	-	500	-
4.6.4(Edges on moulded toys)	-	500	-
4.6.5(Edges on exposed bolts or threaded rods)	-	500	-
4.7.1(Accessible sharp points)	-	500	-
4.7.2(Functional sharp points)	-	500	-
4.7.3(Wooden toys)	-	500	-
4.8(Projections)	-	500	-
4.9(Metal wires and rods)	-	500	-
4.10(Plastic film or plastic bags in packaging and in toys)	-	500	-
4.11.1(General)	-	500	-
4.11.2(Cords in toys intended for children under 18 months)	-	1100	-
4.11.3(Cords in toys intended for children 18 months and over but under 36 months)	-	500	-
4.11.4(Fixed loops and nooses intended for children under 36 months)	-	500	-
4.11.5(Cords on pull toys)	-	500	-
4.11.6(Electrical cables)	-	1100	-
4.11.7(Diameter of certain cords intended for children under 36 months)	-	500	-
4.11.8(Self-retracting cords intended for children under 36 months)	-	500	-
4.11.9(Toys attached to or intended to be strung across, or otherwise attached to, a cradle, cot, perambulator or carriage)	-	500	-
4.11.10(Cords on toy bags)	-	500	-
4.11.11(Cords, strings and lines for flying toys)	-	500	-
4.12.1(Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.2(Other toys with folding mechanisms)	-	500	-
4.12.3(Hinge-line clearance)	-	500	-
4.13.1(Circular holes in rigid materials)	-	500	-
4.13.2(Accessible clearances for movable ,segments)	-	500	-
4.13.3(Chains or belts in ride-on toys)	-	500	-
4.13.4(Other driving mechanisms)	-	500	-
4.13.5(Winding keys)	-	500	-
4.14(Springs)	-	500	-
4.15.1.1(Sideways stability, feet available for stabilization)	-	500	-
4.15.1.2(Sideways stability, feet unavailable for stabilization)	-	500	-
4.15.1.3(Fore and aft stability)	-	500	-
4.15.2(Overload requirements for ride-on toys and seats)	-	500	-
4.15.3(Stability of stationary floor toys)	-	500	-
4.16.1(Ventilation)	-	500	-
4.16.2.1(Lids, doors and similar devices)	-	1500	-
4.16.2.2(Lid support for toy chests and similar toys)	-	1500	-
4.16.3(Toys that enclose the head)	-	1500	-
4.17(Simulated protective equipment, such as helmets, hats and goggles)	-	500	-
4.18.2(Projectiles)	-	500	-
4.18.3(Projectile toys with stored energy)	-	500	-
4.18.4(Projectile toys without stored energy)	-	500	-
4.19(Rotors and propellers)	-	500	-
4.20(Aquatic toys)	-	500	-
4.21(Braking)	-	500	-
4.22.1(Instructions for use)	-	500	-
4.22.2(Determination of maximum saddle height)	-	500	-
4.22.3(Braking requirements)	-	500	-
4.23(Speed limitation of electrically driven ride-on toys)	-	500	-
4.24(Toys containing a heat source)	-	500	-
4.25(Liquid -filled toys)	-	1200	500+700
4.26(Mouth - actuated toys)	-	500	-
4.27(Toy roller skates, toy inline skates and toy skateboards)	-	500	-
4.28(Percussion caps specifically designed for use in toys)	-	500	-
4.29(Acoustic requirements)	-	500	-
4.30.2(Warnings and instructions for use)	-	500	-
4.30.3(Strength)	-	500	-
4.30.4(Stability)	-	500	-
4.30.5(Adjustable and folding steering tubes and handlebars)	-	500	-
4.30.6(Braking)	-	500	-
4.30.7(Wheel size)	-	500	-
4.30.8(Projections)	-	500	-
4.31.1(Magnetic/electrical experimental sets intended for children 8 years and over)	-	500	-
4.31.2(All other toys with magnets and magnetic components)	-	500	-
4.32(Yo-yo balls)	-	500	-
4.33(Straps intended to be worn fully or partially around the neck)	-	500	-
4.34(Sledges and toboggans with cords for pulling)	-	500	-
4.35(Jaw entrapment in handles and steering wheels)	-	500	-

31 Dec, 2026

-
Included w.e.f 17.10.2024 For Part-1 only

IS 17399 (2020)

Textiles - Polypropylene ( PP )/ High Density Polyethylene ( HDPE ) Laminated Woven Sacks for Mail Sorting, Storage, Transport and Distribution - Specification

33355 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(MANUFACTURE - Raw Materials)	-	2000	-
5.2(MANUFACTURE - Fabric for PP tapes & for HDPE tapes)	-	500	-
5.2- Table 1- i)("REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm")	-	500	-
5.2- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	500	-
5.2- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	500	-
5.2- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	500	-
5.2- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf) a) Lengthwise b) Widthwise)	-	2450	1100+250+1100
5.2- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min, N2), (kgf))	-	1100	-
5.2- Table 1- vii)("REQUIREMENTS - Elongation at break of fabric, percent: a) Lengthwise b) Widthwise")	-	0	-
5.2- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	950	-
5.3(Lamination)	-	500	-
5.4(Sack Fabrication)	-	500	-
5.5(Capacity)	-	500	-
6.1- Table 1- i)(REQUIREMENTS - Inside dimensions a) Bottom panel (L × W), mm b) Open top (L × W), mm c) Height (H), mm)	-	500	-
6.1- Table 1- ii)(REQUIREMENTS - Ends per dm)	-	500	-
6.1- Table 1- iii)(REQUIREMENTS - Picks per dm)	-	500	-
6.1- Table 1- iv)(REQUIREMENTS - Mass of laminated sack, g)	-	500	-
6.1- Table 1- v)(REQUIREMENTS - Breaking strength of laminated fabric (Cut strip method1)), Min, N2) (kgf))	-	0	-
6.1- Table 1- vi)(REQUIREMENTS - Seam strength of bottom and side panel seam (Cut strip method), Min)	-	0	-
6.1- Table 1- vii)(REQUIREMENTS - Elongation at break of fabric, percent a) Lengthwise b) Widthwise)	-	0	-
6.1- Table 1- viii)(REQUIREMENTS - Ash content, Max, percent (a) For UV stabilized sacks (b) For non-UV stabilized sacks)	-	0	-
6.4(UV Resistance Test)	-	10180	-
7(PRINTING, PACKAGING AND MARKING)	-	500	-
8(ATMOSPHERIC CONDITIONS FOR SAMPLE CONDITIONING AND TESTING)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 5.4(Sack Fabrication)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-
Clause 5.1(Raw Materials)	-	0	-
"Clause 5.2 Table 1(i)"(Inside dimensions)	-	0	-
"Clause 5.2 Table 1(ii)"(Ends per dm)	-	0	-
"Clause 5.2 Table 1(iii)"(Picks per dm)	-	0	-
"Clause 5.2 Table 1(iv)"("Mass of laminated sack, g")	-	0	-
"Clause 5.2 Table 1(v)"("Breaking strength of laminated fabric")	-	0	-
"Clause 5.2 Table 1(vi)"(Seam strength of bottom and side panel seam)	-	0	-
"Clause 5.2 Table 1(vii)"("Elongation at break of fabric, percent:")	-	0	-
"Clause 5.2 Table 1(viii)"("Ash content, Max, percent")	-	0	-
Clause 5.3(Lamination with a thin film of polypropylene)	-	0	-
Clause 7.3(Marking on Sacks)	-	0	-

31 Dec, 2026

-
Included w.e.f. 15.07.2024

IS 16709 (2017)

Textiles - Polypropylene (PP) woven, laminated, block bottom valve sacks for packaging of 50 kg cement - Specification

15150 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.1(Sack Length)	-	500	-
4.1.2(Sack Width)	-	500	-
4.1.3(Top Closure Width and Bottom Closure Width)	-	500	-
4.1.4(Patch Length)	-	500	-
4.1.5(Patch Height)	-	500	-
4.1.6(Length of Valve)	-	500	-
4.1.7(Width of Valve Sleeve)	-	500	-
4.1.8(Length of Valve Sleeve)	-	500	-
5.1(Raw Material)	-	2000	-
5.2(Fabric)	-	500	-
5.2(Tape density and width)	-	500	-
5.4(Lamination for PP)	-	2000	-
5.4(Lamination for LDPE)	-	500	-
6.1(Mass of Bale)	-	500	-
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	1350	1100+250
6.2.2(Weld Strength of Top and Bottom Closures)	-	1100	-
6.3(Drop Impact Testing of Filled Sacks)	-	1000	-
6.4(Ash Content)	-	1200	-
8(Atomspheric Conditions for Conditioning and Testing)	-	500	-
4.1.1(Sack Length)	-	0	-
4.1.2(Sack Width)	-	0	-
4.1.3(Top Closure Width and Bottom Closure Width)	-	0	-
4.1.4(Patch Length)	-	0	-
4.1.5(Patch Height)	-	0	-
4.1.6(Length of Valve)	-	0	-
4.1.7(Width of Valve Sleeve)	-	0	-
4.1.8(Length of Valve Sleeve)	-	0	-
5.1(Raw Material)	-	0	-
5.2(Fabric)	-	0	-
5.2(Tape density and width)	-	0	-
5.4(Lamination for PP)	-	0	-
5.4(Lamination for LDPE)	-	0	-
6.1(Mass of Bale)	-	0	-
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	0	-
6.2.2(Weld Strength of Top and Bottom Closures)	-	0	-
6.3(Drop Impact Testing of Filled Sacks)	-	0	-
6.4(Ash Content)	-	0	-
8(Atomspheric Conditions for Conditioning and Testing)	-	0	-
Cl-5.6(Capacity)	-	0	-
Cl- 6.6, Table.-1 (ii)(Ends per dm)	-	0	-
Cl-6.6, Table-1 (iii)(Picks per dm)	-	0	-
Cl.6.6, Table-1 (vii)(Elongation at break of fabric)	-	0	-
4.1.1(Sack Length)	-	500	-
4.1.2(Sack Width)	-	500	-
4.1.3(Top Closure Width and Bottom Closure Width)	-	500	-
4.1.4(Patch Length)	-	500	-
4.1.5(Patch Height)	-	500	-
4.1.6(Length of Valve)	-	500	-
4.1.7(Width of Valve Sleeve)	-	500	-
4.1.8(Length of Valve Sleeve)	-	500	-
5.1(Raw Material)	-	1050	-
5.2(Fabric)	-	500	-
5.2(Tape density and width)	-	500	-
5.4(Lamination for PP)	-	500	-
5.4(Lamination for LDPE)	-	500	-
6.1(Mass of Bale)	-	500	-
6.2.1(Breaking Strength and Elongation at Break of Fabric)	-	1350	-
6.2.2(Weld Strength of Top and Bottom Closures)	-	1350	-
6.3(Drop Impact Testing of Filled Sacks)	-	1100	-
6.4(Ash Content)	-	950	-
8(Atomspheric Conditions for Conditioning and Testing)	-	500	-
Cl-5.6(Capacity)	-	500	-
Cl- 6.6, Table.-1 (ii)(Ends per dm)	-	500	-
Cl-6.6, Table-1 (iii)(Picks per dm)	-	500	-
Cl.6.6, Table-1 (vii)(Elongation at break of fabric)	-	0	-

31 Dec, 2026

-
Included w.e.f. 20.08.2024 Exclusion: Cl.6.5 (Air Permeability)

IS 18482 (2023)

Textiles - Sandwich extrusion laminated polypropylene PP woven sacks for packaging bulk commodities - Specification

46380 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.1(Density)	-	700	-
5.1.2(Melt Flow Index)	-	1100	-
5.1.4(Carbon black, Density)	-	700	-
5.1.4(Carbon black, Toluene extract)	-	1100	-
5.1.4(Carbon black, Volatile matter)	-	700	-
5.1.5(UV Stabilizer)	-	2200	-
5.2.1(Visual Appearance)	-	500	-
5.2.2(Film Form)	-	0	-
5.2.4(Odour)	-	0	-
5.3.1.1(Tolerance on thickness)	-	500	-
5.3.1.2(Tolerance on width)	-	500	-
5.3.2(Impact Strength)	-	1100	-
5.3.2, Table 1(Nominal Film Thickness)	-	500	-
5.3.2, Table 1(Impact Failure Mass)	-	1100	-
5.3.3(Tensile Strength at Break)	-	1300	-
5.3.4(Elongation at Break)	-	0	-
5.3.5(Coefficient of Friction)	-	1100	-
5.3.6(Elmendorf Tear Strength)	-	1100	-
5.3.7(Opacity)	-	700	-
5.4, Table 2(Carbon black, percent)	-	925	-
5.4, Table 2(Ash content, percent)	-	1200	-
5.4, Table 2(Carbon black dispersion)	-	700	-
5.5(Service Life)	-	222580	MAXIMUM OF 5502 HORS (100 X 65 RS =6500) +( 40RS X 5402 HRS = 216080) = 216080+6500 = 222580
5.5, Annex D(U. V. Exposure (Service Life of Indian Solar Radiant Exposure 160 Kly))	-	0	MAXIMUM OF 5502 HORS (100 X 65 RS =6500) +( 40RS X 5402 HRS = 216080) = 216080+6500 = 222580
4(Sack Type)	-	500	-
5.2.1(Fabric)	-	500	-
5.2.2(Linear density of tapes)	-	700	-
5.2.4(Unlaminated fabric mass)	-	500	-
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	500	-
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	500	-
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	500	-
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	500	-
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	500	-
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	500	-
5.4.1(Sack)	-	500	-
5.4.1.1(Centre seam)	-	500	-
5.4.1.2(Bottom seam)	-	500	-
5.4.2(Sack)	-	500	-
5.4.3(Sack)	-	500	-
5.4.5(Liner)	-	500	-
6.1.1, Table 1(Inside length)	-	500	-
6.1.1, Table 1(Inside width)	-	500	-
6.1.1, Table 1(Gusset width)	-	500	-
6.1.1, Table 1(Warp per dm)	-	500	-
6.1.1, Table 1(Weft per dm)	-	500	-
6.1.1, Table 1(Mass of laminated fabric)	-	500	-
6.2, Table 1(Average breaking strength - Lengthwise)	-	1100	-
6.2, Table 1(Average breaking strength - Widthwise)	-	1100	-
6.2, Table 1(Breaking strength of bottom seam)	-	1100	-
6.2, Table 1(Breaking strength of centre seam)	-	1100	-
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	1300	-
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	1100	-
6.3(Average breaking strength - Lengthwise after UV exposure)	-	1100	-
6.3(Average breaking strength - Widthwise after UV exposure)	-	1100	-
6.4(Drop Impact Testing of Filled Sacks)	-	1100	-
4(Sack Type)	-	500	-
5.2.1(Fabric)	-	500	-
5.2.2(Linear density of tapes)	-	500	-
5.2.4(Unlaminated fabric mass)	-	500	-
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	500	-
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	500	-
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	500	-
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	500	-
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	500	-
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	500	-
5.4.1(Sack)	-	500	-
5.4.1.1(Centre seam)	-	500	-
5.4.1.2(Bottom seam)	-	500	-
5.4.2(Sack)	-	500	-
5.4.3(Sack)	-	500	-
5.4.5(Liner)	-	500	-
6.1.1, Table 1(Inside length)	-	500	-
6.1.1, Table 1(Inside width)	-	500	-
6.1.1, Table 1(Gusset width)	-	500	-
6.1.1, Table 1(Warp per dm)	-	500	-
6.1.1, Table 1(Weft per dm)	-	500	-
6.1.1, Table 1(Mass of laminated fabric)	-	500	-
6.2, Table 1(Average breaking strength - Lengthwise)	-	1100	-
6.2, Table 1(Average breaking strength - Widthwise)	-	1100	-
6.2, Table 1(Breaking strength of bottom seam)	-	1100	-
6.2, Table 1(Breaking strength of centre seam)	-	1100	-
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	1300	-
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	1300	-
6.3(Average breaking strength - Lengthwise after UV exposure)	-	1100	-
6.3(Average breaking strength - Widthwise after UV exposure)	-	1100	-
6.4(Drop Impact Testing of Filled Sacks)	-	1100	-
4(Sack Type)	-	0	-
5.2.1(Fabric)	-	0	-
5.2.2(Linear density of tapes)	-	0	-
5.2.4(Unlaminated fabric mass)	-	0	-
5.3.1.1.1(Mass of BOPP film in sandwich extrusion lamination)	-	0	-
5.3.1.1.2(Polypropylene coating mass for sandwich extrusion lamination of BOPP film with base PP woven fabric)	-	0	-
5.3.1.1.3(Total mass of BOPP film laminated woven fabric)	-	0	-
5.3.1.2.1(Mass of nonwoven fabric in sandwich extrusion lamination)	-	0	-
5.3.1.2.2(Polypropylene coating mass for sandwich extrusion lamination of non woven fabric with base PP woven fabric)	-	0	-
5.3.1.2.3(The total mass of nonwoven laminated woven fabric)	-	0	-
5.4.1(Sack)	-	0	-
5.4.1.1(Centre seam)	-	0	-
5.4.1.2(Bottom seam)	-	0	-
5.4.2(Sack)	-	0	-
5.4.3(Sack)	-	0	-
5.4.5(Liner)	-	0	-
6.1.1, Table 1(Inside length)	-	0	-
6.1.1, Table 1(Inside width)	-	0	-
6.1.1, Table 1(Gusset width)	-	0	-
6.1.1, Table 1(Warp per dm)	-	0	-
6.1.1, Table 1(Weft per dm)	-	0	-
6.1.1, Table 1(Mass of laminated fabric)	-	0	-
6.2, Table 1(Average breaking strength - Lengthwise)	-	0	-
6.2, Table 1(Average breaking strength - Widthwise)	-	0	-
6.2, Table 1(Breaking strength of bottom seam)	-	0	-
6.2, Table 1(Breaking strength of centre seam)	-	0	-
6.2, Table 1(Average elongation at break of fabric - Lengthwise)	-	0	-
6.2, Table 1(Average elongation at break of fabric - Widthwise)	-	0	-
6.3(Average breaking strength - Lengthwise after UV exposure)	-	0	-
6.3(Average breaking strength - Widthwise after UV exposure)	-	0	-
6.4(Drop Impact Testing of Filled Sacks)	-	0	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 5.4.5.3("Free from pin holes (except for air removal perforations), patches, tears, blisters, and any other visible defects")	-	0	-
Clause 6.2.2(Stitch strength)	-	0	-
Clause 6.2.2(Weld seam strength)	-	0	-
Clause 6.5 Table 1 viii(Ash content)	-	0	-

31 Dec, 2026

-
Included w.e.f. 24.04.2024

IS 16187 (2014)

Textiles - High density polyethylene (HDPE)/ polypropylene (PP) leno woven sacks for packaging and storage of fruits and vegetables - Specification

29530 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause no. 3.1(Raw Material, as applicable: PP Granules (IS 10910) Overall Migration)	-	2000	-
Clause no. 3.1(Raw Material, as applicable: PP Granules (IS 10910) Overall Migration)	-	2000	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	2200	-
Clause no. 3.1(Lead)	-	3000	-
Clause no. 3.1(Arsenic)	-	0	-
Clause no. 3.1(Mercury)	-	0	-
Clause no. 3.1(Cadmium)	-	0	-
Clause no. 3.1(Zinc)	-	0	-
Clause no. 3.1(Selenium)	-	0	-
Clause no. 3.1(Barium)	-	0	-
Clause no. 3.1(Chromium)	-	0	-
Clause no. 3.1(Antimony)	-	0	-
Clause no. 3.1(Total primary aromatic amines (calculated as aniline equivalent))	-	0	-
Clause no. 3.1(Sulphonated aromatic amines (calculated as aniline sulphonic acid))	-	0	-
Clause no. 3.1(Polychlorinated biphenyl (reported as decachloro biphenyl))	-	0	-
Clause no. 3.1(Carcinogenic amine)	-	0	-
Clause no. 3.1(Raw Material, as applicable: HDPE Granules (IS7328))	-	2000	-
Clause no. 3.1(Density)	-	700	-
Clause no. 3.1(Melt flow Index)	-	1100	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	2200	-
Clause no. 3.1(Lead)	-	3000	-
Clause no. 3.1(Arsenic)	-	0	-
Clause no. 3.1(Mercury)	-	0	-
Clause no. 3.1(Cadmium)	-	0	-
Clause no. 3.1(Zinc)	-	0	-
Clause no. 3.1(Selenium)	-	0	-
Clause no. 3.1(Barium)	-	0	-
Clause no. 3.1(Chromium)	-	0	-
Clause no. 3.1(Antimony)	-	0	-
Clause no. 3.1(Total primary aromatic amines (calculated as aniline equivalent))	-	0	-
Clause no. 3.1(Sulphonated aromatic amines (calculated as aniline sulphonic acid))	-	0	-
Clause no. 3.1(Polychlorinated biphenyl (reported as decachloro biphenyl))	-	0	-
Clause no. 3.1(Carcinogenic amine)	-	0	-
3.1(Raw Material - The tape shall be manufactured from virgin food grade high density polyethylene (HDPE)/polypropylene (PP))	-	500	-
3.2(Fabric - The fabric used in the manufacture of HDPE/PP leno woven sacks shall be woven as a tube on circular loom from HDPE/PP tapes having width in the range of 2.0-2.5 mm)	-	500	-
3.3.1(Sack - Leno sacks fabricated out of woven fabric shall have seam at the bottom and/or side.The stitching shall be done with two rows of either lock stitch or chain stitch)	-	500	-
3.3.2(The tape or thread used for stitching shall have at least 20 percent higher denier than that used for making of the sack)	-	500	-
3.3.3(Sack - Bag Mouth)	-	500	-
3.3.4("Sack - sacks shall have nominal holding capacities of 25 kg and Type 2, sacks shall have nominal holding capacities of 50 kg")	-	500	-
4.1- Table 1- i)(Requirements of HDPE/PP Leno Woven Sacks - Capacity)	-	500	-
4.1- Table 1- ii)(Requirements of HDPE/PP Leno Woven Sacks - Dimensions, cm a) Inside length b) Inside width)	-	500	-
4.1- Table 1- iii)(Requirements of HDPE/PP Leno Woven Sacks - Mass of fabric, g/m2)	-	500	-
4.1- Table 1- iv)(Requirements of HDPE/PP Leno Woven Sacks - Ends per dm)	-	2200	-
4.1- Table 1- v)(Requirements of HDPE/PP Leno Woven Sacks - Picks per dm)	-	2200	-
4.1- Table 1- vi)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of fabric (cut strip method), N (kgf) a) Lengthwise b) Widthwise)	-	2200	-
4.1- Table 1- vii)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of bottom /side seam (cut strip method), N (kgf))	-	2200	-
4.2(Requirements - UV Resistance)	-	8480	-
4.3(Requirements - Mass of Bale As per Annex C)	-	500	-
5.1(LABELLING, PACKING AND MARKING - Labelling on Sacks)	-	500	-
5.2(Packing)	-	500	-
5.3(Marking)	-	500	-
6(ATMOSPHERIC CONDITIONS, CONDITIONING AND TESTING)	-	500	-
Clause no. 3.1(Raw Material, as applicable: PP Granules (IS 10910) Overall Migration)	-	1050	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	2000	-
Clause no. 3.1(Lead)	-	0	-
Clause no. 3.1(Arsenic)	-	0	-
Clause no. 3.1(Mercury)	-	0	-
Clause no. 3.1(Cadmium)	-	0	-
Clause no. 3.1(Zinc)	-	0	-
Clause no. 3.1(Selenium)	-	0	-
Clause no. 3.1(Barium)	-	0	-
Clause no. 3.1(Chromium)	-	0	-
Clause no. 3.1(Antimony)	-	0	-
Clause no. 3.1(Total primary aromatic amines (calculated as aniline equivalent))	-	0	-
Clause no. 3.1(Sulphonated aromatic amines (calculated as aniline sulphonic acid))	-	0	-
Clause no. 3.1(Polychlorinated biphenyl (reported as decachloro biphenyl))	-	0	-
Clause no. 3.1(Carcinogenic amine)	-	0	-
Clause no. 3.1(Raw Material, as applicable: HDPE Granules (IS7328))	-	0	-
Clause no. 3.1(Density)	-	700	-
Clause no. 3.1(Melt flow Index)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
Clause no. 3.1(Lead)	-	0	-
Clause no. 3.1(Arsenic)	-	0	-
Clause no. 3.1(Mercury)	-	0	-
Clause no. 3.1(Cadmium)	-	0	-
Clause no. 3.1(Zinc)	-	0	-
Clause no. 3.1(Selenium)	-	0	-
Clause no. 3.1(Barium)	-	0	-
Clause no. 3.1(Chromium)	-	0	-
Clause no. 3.1(Antimony)	-	0	-
Clause no. 3.1(Total primary aromatic amines (calculated as aniline equivalent))	-	0	-
Clause no. 3.1(Sulphonated aromatic amines (calculated as aniline sulphonic acid))	-	0	-
Clause no. 3.1(Polychlorinated biphenyl (reported as decachloro biphenyl))	-	0	-
Clause no. 3.1(Carcinogenic amine)	-	0	-
3.1(Raw Material - The tape shall be manufactured from virgin food grade high density polyethylene (HDPE)/polypropylene (PP))	-	0	-
3.2(Fabric - The fabric used in the manufacture of HDPE/PP leno woven sacks shall be woven as a tube on circular loom from HDPE/PP tapes having width in the range of 2.0-2.5 mm)	-	0	-
3.3.1(Sack - Leno sacks fabricated out of woven fabric shall have seam at the bottom and/or side.The stitching shall be done with two rows of either lock stitch or chain stitch)	-	0	-
3.3.2(The tape or thread used for stitching shall have at least 20 percent higher denier than that used for making of the sack)	-	0	-
3.3.3(Sack - Bag Mouth)	-	0	-
3.3.4("Sack - sacks shall have nominal holding capacities of 25 kg and Type 2, sacks shall have nominal holding capacities of 50 kg")	-	0	-
4.1- Table 1- i)(Requirements of HDPE/PP Leno Woven Sacks - Capacity)	-	0	-
4.1- Table 1- ii)(Requirements of HDPE/PP Leno Woven Sacks - Dimensions, cm a) Inside length b) Inside width)	-	0	-
4.1- Table 1- iii)(Requirements of HDPE/PP Leno Woven Sacks - Mass of fabric, g/m2)	-	0	-
4.1- Table 1- iv)(Requirements of HDPE/PP Leno Woven Sacks - Ends per dm)	-	0	-
4.1- Table 1- v)(Requirements of HDPE/PP Leno Woven Sacks - Picks per dm)	-	0	-
4.1- Table 1- vi)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of fabric (cut strip method), N (kgf) a) Lengthwise b) Widthwise)	-	0	-
4.1- Table 1- vii)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of bottom /side seam (cut strip method), N (kgf))	-	0	-
4.2(Requirements - UV Resistance)	-	0	-
4.3(Requirements - Mass of Bale As per Annex C)	-	0	-
5.1(LABELLING, PACKING AND MARKING - Labelling on Sacks)	-	0	-
5.2(Packing)	-	0	-
5.3(Marking)	-	0	-
6(ATMOSPHERIC CONDITIONS, CONDITIONING AND TESTING)	-	0	-
Clause no. 3.1(Raw Material, as applicable: PP Granules (IS 10910) Overall Migration)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
Clause no. 3.1(Density)	-	0	-
Clause no. 3.1(Melt flow Index)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
3.1(Raw Material - The tape shall be manufactured from virgin food grade high density polyethylene (HDPE)/polypropylene (PP))	-	0	-
3.2(Fabric - The fabric used in the manufacture of HDPE/PP leno woven sacks shall be woven as a tube on circular loom from HDPE/PP tapes having width in the range of 2.0-2.5 mm)	-	0	-
3.3.1(Sack - Leno sacks fabricated out of woven fabric shall have seam at the bottom and/or side.The stitching shall be done with two rows of either lock stitch or chain stitch)	-	0	-
3.3.2(The tape or thread used for stitching shall have at least 20 percent higher denier than that used for making of the sack)	-	0	-
3.3.3(Sack - Bag Mouth)	-	0	-
3.3.4("Sack - sacks shall have nominal holding capacities of 25 kg and Type 2, sacks shall have nominal holding capacities of 50 kg")	-	0	-
4.1- Table 1- i)(Requirements of HDPE/PP Leno Woven Sacks - Capacity)	-	0	-
4.1- Table 1- ii)(Requirements of HDPE/PP Leno Woven Sacks - Dimensions, cm a) Inside length b) Inside width)	-	0	-
4.1- Table 1- iii)(Requirements of HDPE/PP Leno Woven Sacks - Mass of fabric, g/m2)	-	0	-
4.1- Table 1- iv)(Requirements of HDPE/PP Leno Woven Sacks - Ends per dm)	-	0	-
4.1- Table 1- v)(Requirements of HDPE/PP Leno Woven Sacks - Picks per dm)	-	0	-
4.1- Table 1- vi)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of fabric (cut strip method), N (kgf) a) Lengthwise b) Widthwise)	-	0	-
4.1- Table 1- vii)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of bottom /side seam (cut strip method), N (kgf))	-	0	-
4.2(Requirements - UV Resistance)	-	0	-
4.3(Requirements - Mass of Bale As per Annex C)	-	0	-
5.1(LABELLING, PACKING AND MARKING - Labelling on Sacks)	-	0	-
5.2(Packing)	-	0	-
5.3(Marking)	-	0	-
6(ATMOSPHERIC CONDITIONS, CONDITIONING AND TESTING)	-	0	-
Clause no. 3.1(Raw Material, as applicable: PP Granules (IS 10910) Overall Migration)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
Clause no. 3.1(Density)	-	0	-
Clause no. 3.1(Melt flow Index)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
3.1(Raw Material - The tape shall be manufactured from virgin food grade high density polyethylene (HDPE)/polypropylene (PP))	-	0	-
3.2(Fabric - The fabric used in the manufacture of HDPE/PP leno woven sacks shall be woven as a tube on circular loom from HDPE/PP tapes having width in the range of 2.0-2.5 mm)	-	0	-
3.3.1(Sack - Leno sacks fabricated out of woven fabric shall have seam at the bottom and/or side.The stitching shall be done with two rows of either lock stitch or chain stitch)	-	0	-
3.3.2(The tape or thread used for stitching shall have at least 20 percent higher denier than that used for making of the sack)	-	0	-
3.3.3(Sack - Bag Mouth)	-	0	-
3.3.4("Sack - sacks shall have nominal holding capacities of 25 kg and Type 2, sacks shall have nominal holding capacities of 50 kg")	-	0	-
4.1- Table 1- i)(Requirements of HDPE/PP Leno Woven Sacks - Capacity)	-	0	-
4.1- Table 1- ii)(Requirements of HDPE/PP Leno Woven Sacks - Dimensions, cm a) Inside length b) Inside width)	-	0	-
4.1- Table 1- iii)(Requirements of HDPE/PP Leno Woven Sacks - Mass of fabric, g/m2)	-	0	-
4.1- Table 1- iv)(Requirements of HDPE/PP Leno Woven Sacks - Ends per dm)	-	0	-
4.1- Table 1- v)(Requirements of HDPE/PP Leno Woven Sacks - Picks per dm)	-	0	-
4.1- Table 1- vi)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of fabric (cut strip method), N (kgf) a) Lengthwise b) Widthwise)	-	0	-
4.1- Table 1- vii)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of bottom /side seam (cut strip method), N (kgf))	-	0	-
4.2(Requirements - UV Resistance)	-	0	-
4.3(Requirements - Mass of Bale As per Annex C)	-	0	-
5.1(LABELLING, PACKING AND MARKING - Labelling on Sacks)	-	0	-
5.2(Packing)	-	0	-
5.3(Marking)	-	0	-
6(ATMOSPHERIC CONDITIONS, CONDITIONING AND TESTING)	-	0	-
Clause no. 3.1(Raw Material, as applicable: PP Granules (IS 10910) Overall Migration)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
Clause no. 3.1(Density)	-	0	-
Clause no. 3.1(Melt flow Index)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
3.1(Raw Material - The tape shall be manufactured from virgin food grade high density polyethylene (HDPE)/polypropylene (PP))	-	0	-
3.2(Fabric - The fabric used in the manufacture of HDPE/PP leno woven sacks shall be woven as a tube on circular loom from HDPE/PP tapes having width in the range of 2.0-2.5 mm)	-	0	-
3.3.1(Sack - Leno sacks fabricated out of woven fabric shall have seam at the bottom and/or side.The stitching shall be done with two rows of either lock stitch or chain stitch)	-	0	-
3.3.2(The tape or thread used for stitching shall have at least 20 percent higher denier than that used for making of the sack)	-	0	-
3.3.3(Sack - Bag Mouth)	-	0	-
3.3.4("Sack - sacks shall have nominal holding capacities of 25 kg and Type 2, sacks shall have nominal holding capacities of 50 kg")	-	0	-
4.1- Table 1- i)(Requirements of HDPE/PP Leno Woven Sacks - Capacity)	-	0	-
4.1- Table 1- ii)(Requirements of HDPE/PP Leno Woven Sacks - Dimensions, cm a) Inside length b) Inside width)	-	0	-
4.1- Table 1- iii)(Requirements of HDPE/PP Leno Woven Sacks - Mass of fabric, g/m2)	-	0	-
4.1- Table 1- iv)(Requirements of HDPE/PP Leno Woven Sacks - Ends per dm)	-	0	-
4.1- Table 1- v)(Requirements of HDPE/PP Leno Woven Sacks - Picks per dm)	-	0	-
4.1- Table 1- vi)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of fabric (cut strip method), N (kgf) a) Lengthwise b) Widthwise)	-	0	-
4.1- Table 1- vii)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of bottom /side seam (cut strip method), N (kgf))	-	0	-
4.2(Requirements - UV Resistance)	-	0	-
4.3(Requirements - Mass of Bale As per Annex C)	-	0	-
5.1(LABELLING, PACKING AND MARKING - Labelling on Sacks)	-	0	-
5.2(Packing)	-	0	-
5.3(Marking)	-	0	-
6(ATMOSPHERIC CONDITIONS, CONDITIONING AND TESTING)	-	0	-
Clause no. 3.1(Raw Material, as applicable: PP Granules (IS 10910) Overall Migration)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
Clause no. 3.1(Density)	-	0	-
Clause no. 3.1(Melt flow Index)	-	0	-
Clause no. 3.1(Colorants, if used (IS 9833): Toxic Elements)	-	0	-
3.1(Raw Material - The tape shall be manufactured from virgin food grade high density polyethylene (HDPE)/polypropylene (PP))	-	0	-
3.2(Fabric - The fabric used in the manufacture of HDPE/PP leno woven sacks shall be woven as a tube on circular loom from HDPE/PP tapes having width in the range of 2.0-2.5 mm)	-	0	-
3.3.1(Sack - Leno sacks fabricated out of woven fabric shall have seam at the bottom and/or side.The stitching shall be done with two rows of either lock stitch or chain stitch)	-	0	-
3.3.2(The tape or thread used for stitching shall have at least 20 percent higher denier than that used for making of the sack)	-	0	-
3.3.3(Sack - Bag Mouth)	-	0	-
3.3.4("Sack - sacks shall have nominal holding capacities of 25 kg and Type 2, sacks shall have nominal holding capacities of 50 kg")	-	0	-
4.1- Table 1- i)(Requirements of HDPE/PP Leno Woven Sacks - Capacity)	-	0	-
4.1- Table 1- ii)(Requirements of HDPE/PP Leno Woven Sacks - Dimensions, cm a) Inside length b) Inside width)	-	0	-
4.1- Table 1- iii)(Requirements of HDPE/PP Leno Woven Sacks - Mass of fabric, g/m2)	-	0	-
4.1- Table 1- iv)(Requirements of HDPE/PP Leno Woven Sacks - Ends per dm)	-	0	-
4.1- Table 1- v)(Requirements of HDPE/PP Leno Woven Sacks - Picks per dm)	-	0	-
4.1- Table 1- vi)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of fabric (cut strip method), N (kgf) a) Lengthwise b) Widthwise)	-	0	-
4.1- Table 1- vii)(Requirements of HDPE/PP Leno Woven Sacks - Average breaking strength of bottom /side seam (cut strip method), N (kgf))	-	0	-
4.2(Requirements - UV Resistance)	-	0	-
4.3(Requirements - Mass of Bale As per Annex C)	-	0	-
5.1(LABELLING, PACKING AND MARKING - Labelling on Sacks)	-	0	-
5.2(Packing)	-	0	-
5.3(Marking)	-	0	-
6(ATMOSPHERIC CONDITIONS, CONDITIONING AND TESTING)	-	0	-
Clause no. 3.1(Raw Material, as applicable: HDPE Granules (IS7328))	-	0	-

31 Dec, 2026

-
Excl: Heavy elements, Aromatic amines, carcinogenic amines, biphenyl in raw material

IS 17546 (2021)

Chlorinated polyvinyl chloride CPVC fittings for potable hot and cold water distribution supplies Specification

163350 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Nominal Size(DN))	-	250	-
3.2(Nominal Outside Diameter)	-	250	-
3.3(Mean Inside Diameter of Socket at Entry)	-	250	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	250	-
3.5(Out-of-Roundness (Ovality))	-	250	-
3.7(Minimum Wall Thickness)	-	250	-
3.11(Type Tests)	-	137600	ALL TYPE TESTS INCLUDING 8760 HR TEST
3.11(Acceptance Tests)	-	850	-
6(Composition)	-	17975	ALL COMPOUND PROPERTIES
8.2(Opacity)	-	575	-
8.4(Vicat softening Temperature)	-	1100	-
8.5(Density)	-	500	-
8.6(Effect on water)	-	3000	-
9(Mechanical Properties)	-	750	-
11(Marking)	-	300	-
3.1(Nominal Size(DN))	-	250	-
3.2(Nominal Outside Diameter)	-	250	-
3.3(Mean Inside Diameter of Socket at Entry)	-	250	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	250	-
3.5(Out-of-Roundness (Ovality))	-	250	-
3.7(Minimum Wall Thickness)	-	250	-
3.11(Type Tests)	-	137600	-
3.11(Acceptance Tests)	-	850	-
6(Composition)	-	17975	-
8.2(Opacity)	-	575	-
8.4(Vicat softening Temperature)	-	1100	-
8.5(Density)	-	500	-
8.6(Effect on water)	-	3000	-
9(Mechanical Properties)	-	700	-
11(Marking)	-	500	-
8.3(Stress Relief Test)	-	700	-
3.1(Nominal Size(DN))	-	500	-
3.2(Nominal Outside Diameter)	-	500	-
3.3(Mean Inside Diameter of Socket at Entry)	-	500	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	500	-
3.5(Out-of-Roundness (Ovality))	-	500	-
3.11(Type Tests)	-	500	-
3.11(Acceptance Tests)	-	1000	-
6(Composition)	-	1100	-
8.2(Opacity)	-	575	-
8.4(Vicat softening Temperature)	-	1100	-
8.5(Density)	-	700	-
8.6(Effect on water)	-	3000	-
9(Mechanical Properties)	-	750	-
11(Marking)	-	500	-
8.3(Stress Relief Test)	-	1000	-
3.6(Nominal Wall Thickness)	-	500	-
3.7(Minimum Wall Thickness)	-	500	-
3.8(Tolerance)	-	500	-
3.9(Working Pressure)	-	500	-
3.1(Standard Dimension Ratio)	-	500	-
8.1(Visual Appearance)	-	500	-
7(Dimensions of fitting)	-	500	-
3.1(Nominal Size(DN))	-	250	-
3.2(Nominal Outside Diameter)	-	250	-
3.3(Mean Inside Diameter of Socket at Entry)	-	250	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	250	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	250	-
3.5(Out-of-Roundness (Ovality))	-	250	-
3.11(Type Tests)	-	137600	-
3.11(Acceptance Tests)	-	850	-
6(Composition)	-	17975	-
8.2(Opacity)	-	575	-
8.4(Vicat softening Temperature)	-	1100	-
8.5(Density)	-	500	-
8.6(Effect on water)	-	3000	-
9(Mechanical Properties)	-	750	-
11(Marking)	-	300	-
8.3(Stress Relief Test)	-	1000	-
3.6(Nominal Wall Thickness)	-	500	-
3.7(Minimum Wall Thickness)	-	500	-
3.8(Tolerance)	-	500	-
3.9(Working Pressure)	-	500	-
3.1(Standard Dimension Ratio)	-	500	-
8.1(Visual Appearance)	-	500	-
7(Dimensions of fitting)	-	500	-
3.1(Nominal Size(DN))	-	0	-
3.2(Nominal Outside Diameter)	-	0	-
3.3(Mean Inside Diameter of Socket at Entry)	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.5(Out-of-Roundness (Ovality))	-	0	-
3.11(Type Tests)	-	0	-
3.11(Acceptance Tests)	-	0	-
6(Composition)	-	0	-
8.2(Opacity)	-	0	-
8.4(Vicat softening Temperature)	-	0	-
8.5(Density)	-	0	-
8.6(Effect on water)	-	0	-
9(Mechanical Properties)	-	0	-
11(Marking)	-	0	-
8.3(Stress Relief Test)	-	0	-
3.6(Nominal Wall Thickness)	-	0	-
3.7(Minimum Wall Thickness)	-	0	-
3.8(Tolerance)	-	0	-
3.9(Working Pressure)	-	0	-
3.1(Standard Dimension Ratio)	-	0	-
8.1(Visual Appearance)	-	0	-
7(Dimensions of fitting)	-	0	-
3.1(Nominal Size(DN))	-	0	-
3.2(Nominal Outside Diameter)	-	0	-
3.3(Mean Inside Diameter of Socket at Entry)	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.4(Mean Inside Diameter of Socket at Shoulder (Bottom))	-	0	-
3.5(Out-of-Roundness (Ovality))	-	0	-
3.11(Type Tests)	-	0	-
3.11(Acceptance Tests)	-	0	-
6(Composition)	-	0	-
8.2(Opacity)	-	0	-
8.4(Vicat softening Temperature)	-	0	-
8.5(Density)	-	0	-
8.6(Effect on water)	-	0	-
9(Mechanical Properties)	-	0	-
11(Marking)	-	0	-
8.3(Stress Relief Test)	-	0	-
3.6(Nominal Wall Thickness)	-	0	-
3.7(Minimum Wall Thickness)	-	0	-
3.8(Tolerance)	-	0	-
3.9(Working Pressure)	-	0	-
3.1(Standard Dimension Ratio)	-	0	-
8.1(Visual Appearance)	-	0	-
7(Dimensions of fitting)	-	0	-
Cl-6.2.2(Compound Chlorine Content)	-	0	-
Cl-6.2.5(Verification of the Malfunction Temperature)	-	0	-
Cl-9.1(Hydrostatic Characteristics)	-	0	-
Cl-9.2(Thermal Stability by Hydrostatic Pressure Testing)	-	0	-

31 Dec, 2026

-
Included w.e.f.04-04-2024.

IS 17425 (2020)

Irrigation Equipment - Quick Coupled Polyethylene Pipes and Fittings for Sprinkler Irrigation Systems - Specification

65550 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Dimensions of pipe - i) Outside diameter)	-	250	-
5(Dimensions of pipe - ii) Wall thickness minimum)	-	250	-
6(Visual Appearance)	-	300	-
7.1(Hydraulic Characteristics - Quality test)	-	4800	-
7.1(Hydraulic Characteristics - Acceptance test)	-	1600	-
7.2(Reversion Test)	-	1000	700+300
7.3(Tensile Test- i) Tensile Strength)	-	1350	1100+250
7.3(Tensile Test - ii)Elongation at Break)	-	0	-
7.4(Fusion Compatibility Test- a) Quality test)	-	4800	-
7.4(Fusion Compatibility Test- b) Acceptance test)	-	1600	-
7.5(Density)	-	500	-
7.6(Melt Flow Rate)	-	1100	-
4.2(Carbon black- a)carbon content)	-	925	-
4.2(Carbon black- b) Dispersion of carbon black)	-	700	-
7.4 Table-2(Fusion Compatibility Test)	-	4800	-
6.1(VISUAL APPEARANCE)	-	300	-
5.1.2(Ovality)	-	250	-
4.1.2(The MFR of the material shall be between 0.2 to 1.1 (both inclusive) when tested at 190 T at a nominal load of 50 N by the method prescribed in 7 of IS 2530. The MFR of the material shall also be within 20% of the value declared by the manufacturer.’)	-	1100	-
4.1.1(density shall be between 940.4 kg/m’ and 958.4 kg/m3 (both inclusive) when determined at 27°C according to procedure prescribed in Annex A of IS 7328. The value of the density shall also not differ from the nominal value by more than 3 kg/m2 as per 5.2.1.1 of IS 7328.)	-	500	-
Cl. 4.2 , IS 2530-1963, Cl. 10(Cabon Black Content)	-	925	-
4.1.3(Workmanship and appearance)	-	300	-
4.1.4(Holding attachments for coupler parts)	-	850	-
6.1.3(Weldability Test- a) Quality test)	-	4800	-
6.1.3(Weldability Test- b) Acceptance test)	-	1600	-
4.1 (a)(Quick Coupled Male and Female Couplers)	-	500	-
4.1 (b)(HDPE couplers —)	-	2200	-
6.1.1, 6.1.1.1(Leakage Test)	-	850	-
6.1.2, 6.1.2.1(Hydraulic Proof Test)	-	850	-

31 Dec, 2026

-
-

IS 16098 Part 2 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 2 Pipes and Fittings with Non-Smooth External Surface, Type B

99000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 Table-10 (i)(Ring Stiffness)	-	1100	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	500	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	1100	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	2200	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	1100	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	4800	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	11000	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	1100	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	500	-
6.3.2(Length of Pipe)	-	250	-
8.1.1 Table-10 (iv)(Creep ratio)	-	26300	25200+1100
6.3.3(Out Side Diameter)	-	250	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	1100	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	250	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	1000	-
6.3.5.2(Wall Thickness(e4 min))	-	250	-
9 Table 12 (ii)(Water tightness)	-	1000	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	250	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	39000	-
7.1(Appearance)	-	300	-
7.1.1(Color of Finished Pipes)	-	300	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	1100	-

31 Dec, 2026

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

31025 View breakup
For Elastomeric Sealing Ring Socket Pipe : Rs. 26,825/- , For BIS Samples Rs. 20,244/-; For Plain Ended/Socket Ended Pipes : Rs. 20,975, For BIS Samples Rs. 15,856/-; For Plumbing Pipes : Rs. 9,975, For BIS Samples Rs. 7,606/-; For PVC Resin : Rs. 4,100/- , For BIS Samples Rs. 3,075/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300	-
10.1(Surface Finish)	-	300	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	250	-
10.7(Sulphated Ash Content)	-	950	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	250	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	250	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	250	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	250	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	250	-
9.1(PIPE ENDS)	-	300	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1000	700+300
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	-
11.2(Resistance to External Blows at 0°C)	-	1400	1100+300
10.3(Effect on Water Test)	-	3000	-
6.1.2(PVC Resin)	-	4100	3000+1100

31 Dec, 2026

-
REVISED VERSION OF IS 4985:2021 INCLUDED W.E.F. 14-10-2021. Size upto 400mm.

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

19062 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	1050	--
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	1050	--
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	2000	--
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	1125	500+625
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	1000	--
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	700	--
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	925	--
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	--
6.2.2(Fittings)	-	250	--
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000	--
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	1000	--
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000	--
8.2.1(Unregu/Qt~d Emining Pipe)	-	0	--
8.2.2(Regulated Emitting Pipes)	-	1000	--
8.3.1(Wall Thickness ofEmitting Pipe)	-	250	--
8.3.2(Inside Diameter ofEmitting Pipe)	-	250	--
8.3.3(Flow Paths in Emitting Unit)	-	200	--
8.3.4(Spacing ofEmitter Units)	-	200	--
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000	--
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1600	--
8.5(Resistance to Tension at Elevated Temperature)	-	1100	--
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	400	--
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1200	--
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1600	--
8.8(Determination of Emitting Unit Exponent)	-	600	--
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	--
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	--
4.1 a(Identification)	-	1050	-
4.1 a(Identification)	-	1050	-
4.1 d(Density)	-	500	-
4.1 c(Volatile matter Extract)	-	800	-
4.2(Carbon black content)	-	925	-
4.2(Carbon black dispersion)	-	700	-

31 Dec, 2026

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

49525 View breakup
Rs. 49525/-; For BIS Samples : Rs. 31,869/- ; Raw Material : Rs. 5,825/-; For BIS Sample : Rs. 4,525/-; For Carbon Black Master Batch : Rs. 1,875/-; For BIS Sample : Rs. 1,406/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 5.1 table-1(MATERIALS)	-	0	--
5.2(Polyethylene Resin)	-	1050	--
5.3 (a)(Carbon Black Master Batch)	-	1875	925+950
5.3(b)(Carbon Black Master Batch)	-	500	--
5.3(c)(Carbon Black Master Batch)	-	900	--
5.3(d)(Carbon Black Master Batch)	-	700	--
5.3(e)(Carbon Black Master Batch)	-	950	--
8.3(Carbon black)	-	925	--
8.6(Overall migration)	-	2000	1700+300
6, 6.1(PIPE DESCRIPTION)	-	0	--
6.2(Colour)	-	300	--
6.2.1(6.1.1 Identification Stripes)	-	250	--
7.2(Length)	-	250	--
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	500	--
7.4.1.2(Ovality)	-	250	--
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	100 hrs test=4000 48 hrs test =1600 165 hrs test =4800 1000 hrs test = 11000
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	--
8.2(Longitudinal Reversion Test)	-	900	700+200
8.4( Melt Flow Rate)	-	1100	--
8.5 (Oxidation Induction Time)	-	2200	--
8.7(Density)	-	500	--
8.8(Tensile Strength for Butt-fusion)	-	1600	--
8.9 table-6(Elongation at Break)	-	1600	--
8.10(Slow Crack Growth Rate)	-	6000	5500+500

31 Dec, 2026

-
Size upto 400mm

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

13850 View breakup
For Storage Tanks upto 1500 litres: Rs. 17,150/-, For BIS Samples Rs. 13,175/-; For Storage Tanks above 1500 litres: Rs. 18,050/-, For BIS Samples Rs. 13,850/- .

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925	Carbon black content *
4.2.3(Carbon Dispersion Test)	-	700	Carbon black content
5(Types and Features )	-	3100	Net & Gross Capacity 500 Overall Diameter 250 Overall Height 250 Internal dia of man - hole 250 Wall thickness upon effective height 250 Wall thickness above effective height 250 Minimum weight without lid 500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.3(Types and Features )	-	0	included in Types and feature
5.6(Types and Features )	-	0	included in Types and feature
6.1(Finish)	-	300	Finish / Visual Appearance
7.1.1(Resistance to Deformation)	-	700	Resistance to deformation
7.1.2(Resistance to Deformation)	-	0	Resistance to deformation
7.2(Resistance to Impact)	-	1100	Resistance to impact
7.3(Test for Top Load Resistance)	-	900	Top load resistance (for 1500 lit and more)
7.4(Tensile Strength)	-	1100	Tensile Strength
7.5(Flexural Modulus)	-	1100	Flexural modulus
7.6(overall Migration)	-	1700	Overall Migration 40°C / Water/ 10 days

31 Dec, 2026

-
-

IS 16098 Part 2 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 2 Pipes and Fittings with Non-Smooth External Surface, Type B

99000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.1.1 Table-10 (i)(Ring Stiffness)	-	1100	-
Table -1 Cl. No. 5.1, i)(Base Density)	-	500	-
Table -1 Cl. No. 5.1, ii)(Melt Flow Rate (MFR) at (190ºC, 5kg load))	-	1100	-
Table -1 Cl. No. 5.1, iii)(Thermal Stability (Oxidation Induction Test, OIT) at 200ºC)	-	2200	-
8.1.1 Table-10 (ii)(Impact Strength at (0±1 ºC))	-	1100	-
" 5.1 Table-2 ", i)(Resistance to Internal Pressure 165hrs)	-	4800	-
" 5.1 Table-2 ", ii)(Resistance to Internal Pressure 1000hrs)	-	11000	-
8.1.1, 8.1.2 Table-10 (iii)(Ring flexibility 30% of dem)	-	1100	-
6.3.1 & Table-5(Dim (min.) E4 (min) E5 (min.) Socket Length)	-	500	-
6.3.2(Length of Pipe)	-	250	-
8.1.1 Table-10 (iv)(Creep ratio)	-	26300	25200+1100
6.3.3(Out Side Diameter)	-	250	-
6.3.5.1.1(Ring Stiffness of Spigot + socket)	-	1100	-
"6.3.5.1.5 Table-5 "(Socket thickness Avg. (min.) Avg.)	-	250	-
9 Table-12 (i)(Tightness of elastomeric ring seal Joint)	-	1000	-
6.3.5.2(Wall Thickness(e4 min))	-	250	-
9 Table 12 (ii)(Water tightness)	-	1000	-
6.3.5.2("Construction Height of body wall(ec) Wall Thickness (emin) ")	-	250	-
9 Table- 12 (iii)(Resistance to combined temperature cycling and external loading)	-	39000	-
7.1(Appearance)	-	300	-
7.1.1(Color of Finished Pipes)	-	300	-
7.2 Table-6 (i)(Resistance to Heating oven test at (110±2ºC for 30 minute))	-	1100	-

31 Dec, 2026

-
-

IS 15532 (2004)

Plastics crates for fruits and vegetables - Specification

11250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Material)	-	2000	-
3.3(Shape, Dimensions and Design)	-	500	-
3.4(Mass)	-	250	-
3.5(Appearance and Surface Finish)	-	300	-
3.6(Dimensional Stability)	-	700	-
3.7(Confluence Line Strength)	-	1100	-
3.8.1(Compressive Strength (Resistance to Applied Load))	-	1100	-
3.8.2(Resistance to Drop)	-	1100	-
3.9(Resistance to Environmental Stress Cracking)	-	1200	-
3.10.1(Suspension Test)	-	2200	-
3.10.2(Free-Fall Test)	-	0	INCLUDED IN SUSPENSION TEST

31 Dec, 2026

-
-

IS 4985 (2021)

UNPLASTICIZED PVC PIPES FOR POTABLE WATER SUPPLIES SPECIFICATION Fourth Revision

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10.1(Colour)	-	300	-
10.1(Surface Finish)	-	300	-
7.2.1.1 Table3(Angle of taper (Note-1))	-	250	-
10.7(Sulphated Ash Content)	-	950	-
7.1.1.1(DIMENSIONS-PIPE-Mean O.D. (Minimum))	-	250	-
7.1.1.2(DIMENSIONS-PIPE-O.D. at any Point (Minimum))	-	250	-
7.1.2.1(DIMENSIONS-PIPE-Thickness(Minimum))	-	250	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Minimum Length)	-	250	-
7.2.1.1-Table 3(DIMENSIONS-Socket-Sockets for solvent cement jointing-Diameter at mid point of the socket length (Minimum))	-	250	-
9.1(PIPE ENDS)	-	300	-
10.2(PHYSICAL AND CHEMICAL CHARACTERISTICS-Opacity)	-	575	-
10.4(PHYSICAL AND CHEMICAL CHARACTERISTICS- Reversion Test)	-	1000	700+300
10.5(PHYSICAL AND CHEMICAL CHARACTERISTICS- Vicat Softening Temperature)	-	1100	-
10.6(PHYSICAL AND CHEMICAL CHARACTERISTICS- Density)	-	500	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test))	-	11000	-
11.1-Table 6(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test))	-	850	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Type Test)-for Integral Sealing Ring Sockets)	-	11000	-
11.1-Table 7(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Integral Sealing Ring Sockets)	-	850	-
11.1.1(MECHANICAL PROPERTIES-Hydrostatic Pressure Test (Acceptance Test)-for Plumbing pipes)	-	850	-
11.2(Resistance to External Blows at 0°C)	-	1400	1100+300
10.3(Effect on Water Test)	-	3000	-
6.1.2(PVC Resin)	-	4100	3000+1100

31 Dec, 2026

-
REVISED VERSION OF IS 4985:2021 INCLUDED W.E.F. 14-10-2021. Size upto 400mm.

IS 16352 (2020)

Geosynthetics – High density polyethylene (HDPE) geomembranes for lining – Specification (first revision)

160675 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5,3.1, Table1,x) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black content)	-	925	--
5,3.1, Table2,iii) Type I / II / III / IV / V / VI Annex K(Lowest individual of 10 thickness value)	-	1800	--
5,3.1, Table1,iii) Type I / II / III / IV / V / VI / VII Method A of IS 13162 (Part 3)(Lowest individual of 10 thickness value)	-	750	Length, Width & thickness
5,3.1, Table 2,v) d) Type I / II / III / IV / V / VI Annex B(Tensile properties: Breaking elongation)	-	2700	--
5,3.1, Table1,xv) Type I / II / III / IV / V / VI / VII Annex J(Stress crack resistance)	-	1350	--
5,3.1, Table 2,xvi) Type I / II / III / IV / V / VI Annex J(Stress crack resistance)	-	1350	--
5,3.1, Table1,xii) Type I / II / III / IV / V / VI / VII ISO 11357 (Part 6) or ASTM D 5885(Oxidative induction time (OIT) : a) Standard OIT or b) High pressure OIT)	-	0	--
5,3.1, Table1,xiii) Type I / II / III / IV / V / VI / VII Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	54000	--
5,3.1, Table 2,xiv) Type I / II / III / IV / V / VI Oven method of IS 7016 (Part 8), ISO 11357-6 and ASTM D 5885(Oven ageing at 85°C, Retention of oxidative induction time (OIT) after 90 days : a) Standard OIT or b) High pressure OIT)	-	2200	--
3, 3.1(MATERIAL AND MANUFACTURE)	-	0	--
3, 3.2(MATERIAL AND MANUFACTURE If two or more pieces of geomembranes are used, the material shall be joined together by a suitable heat sealing process keeping an overlap of at least 2.5 cm. )	-	0	--
5,3.1, Table1,v) Type I / II / III / IV / V / VI / VII Annex C(Tear resistance)	-	1350	--
5,3.1, Table 2,vii) Type I / II / III / IV / V / VI Annex D(Puncture resistanc)	-	1100	--
5,3.1, Table1,vii) Type I / II / III / IV / V / VI / VII Annex E(Low temperature crack resistance at minus 30°C±1°C)	-	1800	--
5,3.1, Table1,viii) Type I / II / III / IV / V / VI / VII Annex F(Hydrostatic resistance)	-	1800	--
5,3.1, Table1,ix) Type I / II / III / IV / V / VI / VII Annex G(Seam strength : 85 percent of the original actual fabric strength or unbreakable seam)	-	1350	--
5,3.1, Table1,xi) Type I / II / III / IV / V / VI / VII IS 2530(Carbon black dispersion)	-	700	--
5,3.1, Table1,xiv) Type I / II / III / IV / V / VI / VII Annex H(Retention of breaking strength after UV exposure of 144 h : 85 percent of the original actual fabric strength)	-	90350	conditioning charge-89000.00
7, 7.1 Annex M(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS: )	-	300	--
6(DIMENSIONS AND TOLERANCES The dimensions of HDPE geomembrane when tested by the method given in IS 7016 (Part 1) shall be as agreed to between the buyer and the seller. However, the minimum width of the HDPE geomembrane shall be 5000 mm. A combination of panel width may be used to obtain desired width of geomembrane. Narrow width panels not less than 1000 mm in width may also be used but such pieces shall not exceed 1 piece per roll of finished material of specified width.)	-	0	--
7, 7.2(COLOUR, SURFACE CHARACTERISTICS AND FREEDOM FROM DEFECTS)	-	300	--

31 Dec, 2026

-
-

IS 16647 (2017)

Oriented unplasticized polyvinyl chloride (Pvc - O) pipes for water supply - Specification

53875 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.5( Density, g/cc)	-	500	--
9 /9.1 / 27 degree centigrate(MECHANICAL CHARACTERISTICS OF PIPES9./ Resistance to Hydrostatic Pressure)	-	12200	1200+11000
7.3( Opacity)	-	575	--
9.2, table -11( Resistance to External Blows at 0 °C)	-	1000	--
8.2 table-9( Pipe Ends)	-	300	--
5.3(VCM Content)	-	3000	--
5.4( K-Value)	-	1100	--
7.2( Colour)	-	300	--
8.1.1, 8.1.1.2, table-3(Dimension of Pipes / Diameter/8.1.1.2 Diameter at any point)	-	250	--
8.1.2, table 4 to 7(Wall Thickness)	-	250	--
8.1.3 (Length, meter)	-	250	--
8.2 table-9(Dimensions of Integral Socket)	-	250	--
9.3 table-12( Ring Stiffness)	-	1100	--
9.4, annexure-E( Orientation Factor)	-	1400	--
10, table-13( PHYSICAL AND 1CHARACTERISTICS)	-	6200	1100+3000+1000+1100

31 Dec, 2026

-
-

IS 15907 (2010)

Agro textiles – High density polyethylene (HDPE) woven beds for vermiculture – Specification

92830 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3(Cord Beading - IS 15907)	-	250	diameter of rope
5.1(MANUFACTURE- IS 15907)	-	500	dimensions
5.2.1(Lamination- IS 15907)	-	250	dimensions
5.2.2(coating thickness of the sandwich lamination- method A of IS 13162 (Part 3))	-	250	dimensions
5.3.1(Construction- IS 15907)	-	250	dimensions
5.3.1(The width of the hem - IS 15907)	-	250	dimensions
5.3.2(Finished width of pocket - IS 15907)	-	250	dimensions
5.4(Bonding- IS 15907)	-	250	dimensions
6- Table 1- SL.No (i)(Mass)	-	500	gsm
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,warp - IS 1969 )	-	1350	1100+250
6- Table 1- SL.No (ii)(Breaking strength before UV exposure,weft - IS 1969 )	-	1350	1100+250
6- Table 1- SL.No (iii)(Elongation at break of fabric- IS 1969)	-	1350	1100+250
6- Table 1- SL.No (iv)(Retention of breaking strength after UV exposure, - Annex B of IS 15907 and IS 1969)	-	9360	8260 (UV resistance) +1100
6- Table 1- SL.No (v)(Welded seam strength before UV exposure- IS 1969)	-	1350	1100+250
6- Table 1- SL.No (vi)(Welded seam strength after UV exposure- Annex B of IS 15907 and IS 1969)	-	1350	1100+250
6- Table 1- SL.No (vii)(Tear strength, Warp - Method A2 of IS 7016 (Part 3))	-	1350	1100+250
6- Table 1- SL.No (vii)(Tear strength, Weft - Method A2 of IS 7016 (Part 3))	-	1350	1100+250
6- Table 1- SL.No (viii)(Puncture strength - Annex C of IS 15907)	-	1350	1100+250
6- Table 1- SL.No (ix)(Environmental stress cracking test - Annex D of IS 15907)	-	1450	1200+250
6- Table 1- SL.No (x)(Resistance to chemicals, change in the mass - Annex E of IS 15907)	-	2250	2000+250
6- Table 1- SL.No (xi)(Colour fastness to artificial light -IS 2454)	-	1750	1500+250
6- Table 1- SL.No (xii)(Bursting pressure-IS 1966)	-	1350	1100+250
6.1(Length -IS 15907)	-	250	dimensions
6.1(Width - IS 15907)	-	250	dimensions
6.1(Height - IS 15907)	-	250	dimensions
6.2(Water Proofness,IS 7941)	-	1250	1000+250
6.2(Water Proofness, IS 7940)	-	5150	4200 aging charges + 700+250 after aging water proofness

31 Dec, 2026

-
-

IS 15351 (2015)

Agro textiles – Laminated high density polyethylene (HDPE) woven geomembrane for water proof lining – Specification (second revision)

194875 View breakup
Rs.191388/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(HDPE Tapes)	-	1050	--
3.2(HDPE Fabric)	-	1050	--
5.1(Lamination)	-	1300	--
5.2(Panel Width)	-	500	--
5.3(Joints/Seams)	-	250	--
5.1.1 and 6.2(Thickness, mm- IS 7016: Part 1)	-	250	--
5.1.1 and 6.2(Mass, g/sq m)	-	500	--
5.1.1 and 6.2(Dimensions, mm- Annexure A of IS 11652)	-	500	--
5.1.1 and 6.2(Carbon black content, Percent- IS 2530)	-	925	--
5.1.1 and 6.2(Breaking Load on 20 cm X 10 cm Strip, Min )	-	1100	--
Table-1(Breaking load on 20 × 10 cm strip, N, Min after)	-	1100	--
5.1.1 and 6.2( U.V exposure of 1000 h for warp and weft)	-	176500	1000 hrs xenon arc UV exposure
5.1.1 and 6.2(Impact failure load, at 1524 mm drop,)	-	1100	--
5.1.1 and 6.2(Tear resistance, N, Min-Method A1 of IS 7016 (Part 3))	-	1100	--
5.1.1 and 6.2(Puncture resistance, N, Min-Annex D)	-	1100	--
5.1.1 and 6.2(Bursting strength (Ball burst),N/cm², Min-)	-	1100	--
5.1.1 and 6.2(Seam strength before UV exposure (N/mm), Min-IS 15060)	-	1100	--
Table-1(Seam strength after UV exposure N/mm, Min-Annex B and IS 15060)	-	1100	--
5.1.1 and 6.2(Hydrostatic resistance-Annex E)	-	1000	--
Table-1(Hydrostatic resistance after UV exposure of 1000 h -Annex B and Annex E)	-	1000	--
5.1.1 and 6.2(Ash content, percent, Max-Annex F)	-	950	--

31 Dec, 2026

-
INCLUDED W.E.F. 21-09-2021

IS 7903 (2017)

Textiles – Tarpaulins made from high density polyethylene (HDPE) woven fabrics – Specification (fifth revision)

56625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.4( Line/ Cord beading IS 7903)	-	250	--
5.1.1(Lamination IS 7903)	-	250	--
5.1.2(Lamination IS 7903)	-	250	--
5.2.1(Construction IS 7903)	-	300	--
5.3(Joint/Seam, IS 7903)	-	250	--
5.4(Fixing of Eyelets, IS 7903)	-	300	--
6.1 Table 1,i)(No of HDPE fabric layers ,IS 7903)	-	300	--
6.1 Table 1, iii)(Total no of layers in the finished tarpaulin, IS 7903)	-	2000	--
6.1 Table 1,iv)(Mass of finished tarpaulin, Annex B ,IS 7903)	-	500	--
6.1 Table 1,v)(Mass of laminated fabric, Annex C , IS 7903)	-	500	--
6.1 Table 1vi)(Breaking strength before UV exposure,warp ,IS 1969 Part 1)	-	1350	--
6.1 Table 1vi)(Breaking strength before UV exposure,weft, IS 1969 part 1)	-	1350	--
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Warp, IS 13162 part 2& IS 1969 Part1 )	-	29100	--
6.1 Table 1 viii)(Retention of breaking strength after UV exposure of 144h Weft , IS 13162 part 2& IS 1969 Part1 )	-	1350	--
6.1 Table 1 ix)(Welded seam strength before UV exposure (Weft) , IS 1969 Part 1)	-	1350	--
6.1 Table 1 x)(Retention of welded seam strength after UV exposure of 144h(Weft) ,IS 13162 part 2& IS 1969 Part1 )	-	1350	--
6.1 Table 1 xi)(Trapezoidal tear strength, IS 14293)	-	1100	--
6.1 Table 1 xii)(Puncture Resistance, Annex D of IS 7903)	-	1100	--
6.1 Table 1 xiii)(Impact Failure load , at 1524 mmdrop, Annex E of IS 7903)	-	1000	--
6.1 Table 1 xiv)(Color fastness to light (For color Tarpulines) , IS 2454)	-	850	--
6.1 Table 1 xv)(Ash Content, Annex F of IS 7903)	-	950	--
6.2(Length, IS 7903)	-	250	--
6.2(Width, IS 7903)	-	250	--
6.2(height, IS 7903)	-	250	--
6.3(Water Proofness,IS 7941)	-	1000	--
6.3(Water Proofness, IS 7940)	-	1000	--
6.1 Table 1 vii)(Elongation at break of fabric,weft, IS 1969 Part1)	-	1100	--

31 Dec, 2026

-
INCLUDED W.E.F. 21-09-2021

IS 16703 (2017)

Textiles - High density polyethylene (HDPE) polypropylene (PP) woven sacks for packaging of 25 kg polymer materials - Specification

36204.51 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2 Table 1(Dimensions)	-	750	Dimensions
5.2 Table 1(Picks per dm)	-	250	Picks per dm
5.2 Table 1(Mass of sack, Gusseted type, g - IS 1964)	-	250	Mask of sack
5.2 Table 1(Average breaking strength of fabric [Ravelled strip method, 325 mm × 70mm1)] Min, N) (kgf): - IS 1969 (Part 1))	-	2200	average breaking strength( two direction)
5.2 Table 1(Breaking strength of bottom seam (Ravelled strip method), Min, N) (kgf) - IS 9030)	-	1100	Breaking dtrength bottom
5.2 Table 1(Elongation at break of fabric (Ravelled strip method), percent : IS 1969 (Part 1))	-	0	charges included in breaking strength
5.2 Table 1(Drop impact strength)	-	1100	Dro impact
(Clauses 4.2, 5.1, 5.2, 5.3 and 5.4) Table 1 (Ash Content ,a) For UV stabilized sacks)	-	11130	10180 for UV resistance

31 Dec, 2026

-
-

IS 16098 Part 1 (2013)

Structured-Wall Plastics Piping Systems for Non-Pressure Drainage and Sewerage Part 1 Pipes and Fittings With Smooth External Surface, Type A

51950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	500	diameter and wall thickness
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	500	diameter and wall thickness
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	500	diameter and wall thickness
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	600	Visual & Colour
7.3(Physical characteristics for pipes and fittings )	-	600	Visual & Colour
7.4(Resistance to Dichloromethane)	-	1000	nil
7.5(longitudinal reversion)	-	950	nil
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	950	700+250
8.3(Joints)	-	375	hardness
9.1(Ring stiffness)	-	1400	1100+300
9.2(Resistance to external blows at o C)	-	1400	1100+300
9.4(Creep ratio)	-	26300	1100+25200
10.1(Impact Strength of Injection Moulded and Fabricated Fittings)	-	1400	1100+300
11.1(Marking General)	-	300	visual
7.2(Physical characteristics for pipes and fittings )	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.2(Mechanical Characteristics of Fittings)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
11.1(Marking General)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
5.0(Composition of the material)	-	0	-
5.1(Composition of the material)	-	0	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	0	-
5.3(Composition of the material)	-	0	-
5.4(Composition of the material)	-	0	-
6.0(DESIGNATION OF WALL CONSTRUCTIONS AND EXAMPLES OF TYPICAL JOINTING METHODS )	-	0	-
6.1(Wall Construction Designated as Type A)	-	0	-
6.2(Deswignation)	-	0	-
6.3(Dimensions of pipes and fittings)	-	0	-
6.3.1 Table 2(Mean outside diameter)	-	0	-
6.3.2 Table 3(Wall thickness)	-	0	-
6.3.4.2(Fabricated fittings)	-	0	-
6.3.3 Fig 2(Length of pipe)	-	0	-
6.3.4,Table 4,5(Dimensions of Integral sckets and spigot ends)	-	0	-
6.3.4.1(Wall thickness of sockets)	-	0	-
6.3.4.3(Rotational moulded fittings)	-	0	-
6.3.4.4(Type of fittings)	-	0	-
7.0(Physical characteristics of pipes)	-	0	-
7.1(Appearance)	-	0	-
7.2(Colour )	-	0	-
7.3(Vicat softening temperature of pipes)	-	0	-
8.0(Physical characteristics of fittings)	-	0	-
8.1(Appearance and colour)	-	0	-
8.2(Vicat softening temperature of fittings)	-	0	-
8.3(Effect of Heating (Stress Relief Test))	-	0	-
9.0(Mechanical characteristics ofpipes)	-	0	-
9.3(Ring flexibility)	-	0	-
10.0(Mechanical Characteristics of fittings)	-	0	-
11.0(Joints)	-	0	-
11.1(Elastomeric Sealing Rings)	-	0	-
11.2(Solvent cement)	-	0	-
12.0(PERFORMANCE REQUIREMENTS)	-	0	-
12.1(Elastomeric Sealing Ring Joints)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vaccum ))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.2(Solvent cement joints)	-	0	-
12.2.1(Tightness of Solvent cemented Ring Joints )	-	0	-
12.2.2(Tightness of Solvent cemented Ring Joints (Vaccum pressure))	-	0	-
6.3.1(Dimension of Pipes and Fittings Diameter of pipe)	-	0	-
6.3.2(Dimension of Pipes and Fittings Lengths of Pipe)	-	0	-
6.3.3(Dimension of Pipes and Fittings Diameters of Pipes and Spigots of Pipes orFittings)	-	0	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	-
7.1.1(Physical characteristics for pipes and fittings Colour of Finished Pipes)	-	0	-
7.2(Physical characteristics for pipes and fittings )	-	0	-
7.3(Physical characteristics for pipes and fittings )	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
8.1.2 (a)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (b)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (c)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (d)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.1.2 (e)(Mechanical Characteristics of Pipes Ring Flexibility)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.1(Mechanical Characteristics of Fittings General)	-	0	-
8.2.2(Mechanical Characteristics of Fittings)	-	0	-
8.3(Joints)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
11.2.2(Minimum Required Marking Fittings)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
7.0(Physical characteristics for pipes and fittings Appearance)	-	0	-
9 (Table 12)(Performance Requirements)	-	0	-
8.1.1(Mechanical Characteristics of Pipes General)	-	0	-
11.2.1(Minimum Required Marking Pipes)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
7.6(7.6 Effect on Water)	-	0	-
5.2 Table 1(Composition of the material- Resistance to internal hydrostatic Pipe material (1) 1 000 IS 12235 No seepage, cracking, pressure at 60ºC)	-	0	-
6.3.4 Table 4 & 5(Dimensions of Integral Socket and spigot ends)	-	0	-
6.3.4 Table 4 & 5(Outside diameter (dsm) min)	-	0	-
6.3.4 Table 4 & 5(C max)	-	0	-
7.1.1(Colour of finished pipes)	-	0	-
12.1.1(Tightness of Elastomeric Sealing Ring Joints (Water Pressure))	-	0	-
12.1.2(Tightness of Elastomeric Sealing Ring Joints (Internal Vacuum))	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
12.1.3(Resistance to Combined Temperature Cycling and External Loading)	-	0	-
7.6(7.6 Effect on Water)	-	0	-

31 Dec, 2026

-
Size upto 400mm

IS 11584 (1986)

Specification for high density polyethylene (Hdpe) crates for milk satchets

10050 View breakup
Rs. 10050/-, For BIS Samples Rs. 7838/- .

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.2(Material )	-	1050	Material Identification (Chemical Analysis)
2.3(Shape and Dimensions)	-	500	Shape & Dimensions
2.4(Mass )	-	300	Mass
2.5(Appearance and Surface Finish)	-	300	Appearance & surface finish
2.7(Resistance to Stress)	-	1000	Resistance to Stress ( 80°C for 6 hrs)
2.8(Resistance to Applied Load)	-	999.95	Resistance to applied load (100 hrs/270°C)
2.9(Strength)	-	2200	Resistance to drop, Resistance to low temperature drop (6hrs/5°C) (6 x200)
2.1(Dimensional Stability)	-	900	Dimensional stability (80 °C/30 min)

31 Dec, 2026

-
-

IS 10889 (2004)

High density polyethylene films (First Revision)

7675 View breakup
For Black Films : Rs. 7,675/-, For BIS Samples Rs. 5,756/-; For Black Compound : Rs. 3,850/- , For BIS Samples Rs. 3,044/-; For Natural Films : Rs. 6,050/-, For BIS Samples Rs. 4,538/-; For Natural Compound : Rs. 2,225/- , For BIS Samples Rs. 1,825/

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.0(Grades)	-	300	Grade
5.1(Materials)	-	300	Material
5.2(Black Compound)	-	925	Carbon black Content
6.1.1(Appearance)	-	300	Appearance
6.1.2(Film Form)	-	299.95	Film form
6.1.3(Odour )	-	300	odour
6.1.4(Density)	-	500	Density
6.1.5(Melt Flow Rate)	-	1100	Melt Flow Rate
6.1.6(Black Film)	-	700	Carbon black Dispersion
6.2.1, Table 1(Nominal Thickness)	-	250	Thickness
6.2.1, Table 1(Tolerance, Percent Grade 1 and 2)	-	250	Tolerence
6.2.2, Table 2(Nominal Width)	-	250	Width
6.2.2, Table 2(Tolerance, Percent Grade 1 and 2)	-	250	Tlerance
6.3, Table 3(Yield Tolerance)	-	600	Yield tolerance
6.3, Table 3(Tolerance, Percent Grade 1 and 2)	-	250	Tolerance
6.4.1(Tensile Strength at Break)	-	2200	(a) Machine Direction (b) Transverse Direction
6.4.1, Table 4(Direction)	-	1100	Direction
6.4.1, Table 4(Grade 1 and 2)	-	300	Grade
6.4.2(Elongation at Break)	-	2200	Machine Direction Transverse Direction
6.4.2, Table 5(Direction)	-	1100	Direction
6.4.2, Table 5(Elongation at Break, Percent Grade 1 and 2)	-	2200	Machine Direction Transverse Direction
6.4.3(Impact Resistance (Falling Dart))	-	850	Impact Resistance (Falling Dart)
6.4.3, Table 6(Average Thickness of Film)	-	250	Thickness
6.4.3, Table 6(Impact Failure Load)	-	850	Impact failure load

31 Dec, 2026

-
-

IS 7834 : Part 8 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 8 Specific requirements for caps

7514 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2.1(General)	-	5125	Stress Relief test Opacity Effect on water test Short term Hydraulic test (27 °C/1h.)
2.2(Manufacture)	-	500	-
2.2.2(diameter of the socket of cap)	-	500	-
2.1(General)	-	500	-
2.2(Manufacture)	-	500	-
2.2.2(diameter of the socket of cap)	-	500	-
6.1.1(VCM Content Test)	-	3000	-
2.2.2 table 1(Laying length)	-	500	-
6.1.1(VCM Content Test)	-	3000	-
2.2.2 table 1(Laying length)	-	500	-
6.1.1(VCM Content Test)	-	3000	-
2.2.2 table 1(Laying length)	-	500	-

31 Dec, 2026

-
-

IS 7834 : Part 7 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 7 Specific requirements for unions

7514 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	500	Minimum Thickness
table 1 sl.no: 07(63 )	-	500	Minimum Thickness
2.2.3(Socket length)	-	50	Socket length & diameter at Mid point of socket length
2.1(General)	-	5125	Stress Relief test Opacity Effect on water test Short term Hydraulic test (27 °C/1h.)

31 Dec, 2026

-
-

IS 7834 : Part 6 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 6 Specific requirements for sockets

7514 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	500	Minimum Thickness
table 1 sl.no: 19(315.0)	-	500	Minimum Thickness
2.2.3( inside diameter of the socket)	-	500	Socket length & diameter at Mid point of socket length
2.1(General)	-	5126	Stress Relief test Opacity Effect on water test Short term Hydraulic test (27 °C/1h.)

31 Dec, 2026

-
-

IS 7834 : Part 5 (1987)

Injection Moulded PVC Socket Fittings With Solvent Cement Joints for Water Supplies - Part 5 : Specific Requirements for 45 degree Tees

7514 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 (Z) )	-	500	Minimum Thickness
table 1 sl.no: 13(160(z1))	-	500	Minimum Thickness
2.2.3( inside diameter of the socket)	-	500	Socket length & diameter at Mid point of socket length
2.1(General)	-	5125	Stress Relief test Opacity Effect on water test Short term Hydraulic test (27 °C/1h.)
table 1 sl.no: 02(20 (Z) )	-	500	-
table 1 sl.no: 03(25 (Z) )	-	500	-
table 1 sl.no: 04(32 (Z) )	-	500	-
table 1 sl.no: 05(40 (Z) )	-	500	-
table 1 sl.no: 06(50 (Z) )	-	500	-
table 1 sl.no: 07(63 (Z) )	-	500	-
table 1 sl.no: 08(75 (Z) )	-	500	-
table 1 sl.no: 09(90 (Z) )	-	500	-
table 1 sl.no: 10(110 (Z) )	-	500	-
table 1 sl.no: 11(125 (Z) )	-	500	-
table 1 sl.no: 12(140 (Z) )	-	500	-
table 1 sl.no: 13(160(z))	-	500	-
table 1 sl.no: 01(16 (Z1) )	-	500	-
table 1 sl.no: 02(20 (Z1) )	-	500	-
table 1 sl.no: 03(25 (Z1) )	-	500	-
table 1 sl.no: 04(32 (Z1) )	-	500	-
table 1 sl.no: 05(40 (Z1) )	-	500	-
table 1 sl.no: 06(50 (Z1) )	-	500	-
table 1 sl.no: 07(63 (Z1) )	-	500	-
table 1 sl.no: 08(75 (Z1) )	-	500	-
table 1 sl.no: 09(90 (Z) )	-	500	-
table 1 sl.no: 10(110 (Z1) )	-	500	-
table 1 sl.no: 11(125 (Z1) )	-	500	-
table 1 sl.no: 12(140 (Z1) )	-	500	-
2.2.2, Table 1(Size)	-	500	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	500	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	500	-
2.2.3(Socket length)	-	500	-
2.2(Manufacture)	-	500	-
2.2.2, Table 1(Size)	-	500	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z)	-	500	-
2.2.2, Table 1(45 ̊ Tees Laying Length, Z1)	-	500	-
2.2.3( inside diameter of the socket)	-	500	-
2.2.3(Socket length)	-	500	-
6.1.1(VCM Content Test)	-	3000	-
2.2.2 table 1(Laying length)	-	500	-
2.1(General)	-	500	-
2.2(Manufacture)	-	500	-
6.1.1(VCM Content Test)	-	3000	-
2.2.2 table 1(Laying length)	-	500	-

31 Dec, 2026

-
-

IS 7834 : Part 4 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 4 Specific requirements for 90 degree tees

7514 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
table 1 sl.no: 01(16 )	-	500	Minimum Thickness
table 1 sl.no: 19(315.0)	-	500	Minimum Thickness
2.2.3( inside diameter of the socket)	-	500	Socket length & diameter at Mid point of socket length
2.1(General)	-	5125	Stress Relief test Opacity Effect on water test Short term Hydraulic test (27 °C/1h.)

31 Dec, 2026

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET: CSTS, CHHATRAPATI SAMBHAJINAGAR

Plot No. J-3/2, MIDC Industrial Area, Chikalthana, Jalgaon Road, Chhatrapati Sambhajinagar - 431 006, Chhatrapati Sambhajinagar, Aurangabad, Maharashtra, 431006

8602677054 aurangabad@cipet.gov.in

Scope List