BIS - LIMS (Laboratory Information Management System)

CIPET: CENTRE FOR SKILLING AND TECHNICAL SUPPORT (CSTS) - AURANGABAD

Plot No. J-3/2, MIDC Industrial Area, Chikalthana, Jalgaon Road, Aurangabad - 431 006, AURANGABAD, Aurangabad, Maharashtra, 431006

8602677054 aurangabad@cipet.gov.in

Scope List

Reset

68 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 14887 (2014)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sacks for packaging of 50 kg food grains – Specification (first revision)

16700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.2(Tapes – Width and Thickness ( IS 6192/IS 11197))	-	250	Fabric (tape width)
3.2(Tapes – Linear Density (IS 6192/IS 11197))	-	400	Linear density
3.2(Tapes – Tenacity (IS 6192/IS 11197))	-	1100	Tenacity & Elongation
3.2(Tapes – Elongation at point of rupture (IS 6192/IS 11197))	-	1100	Elongation of the Tape at the point of rupture
3.2(Tapes – Heat Shrinkage (HDPE) (Cl. 3.2 and IS 6192))	-	1400	Heat Shrinkage ( at 60 °C ) 700 Heat Shrinkage ( at 95 °C ) 700
3.2(Tapes – Dimensional stability (PP) (IS 11197))	-	1400	Dimensional Stability ( at 100 °C ) 700 Dimensional Stability ( at 125 °C.) 700
3.3.1(Bottom seam (IS 10789))	-	1100	Bottom Seam
4.1 and 3.4(Mass of bale (Cl. 4.1), Capacity (Cl 3.4))	-	250	Capacity
4.2 and Table 1 ii(Dimensions )	-	250	Dimensions (Inside length & width)
5.2 and Table 1 iii(Ends per dm )	-	250	Ends per dm
5.2 and Table 1 iv(Picks per dm )	-	250	Picks per dm
4.2 and Table 1 v(Mass of sack )	-	300	Mass of Sack & GSM
4.2 and Table 1 vi(Average breaking strength of fabric )	-	2200	Avg. Breaking Strength & Elongation at break of Fabric a) Length 1100 b) Widthwise 1100
4.2 and Table 1 vi(Breaking strength of bottom seam )	-	1100	Min. Breaking Strength of Bottom Seam
4.2 and Table 1 viii(Elongation at break of fabric )	-	2200	Avg. Breaking Strength & Elongation at break a) Length 1100 b) Widthwise 1100
4.2 and Table 1 ix(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	2200	Avg. Breaking Strength & Elongation at break of Fabric after UV radiation & weathering a) Length 1100 b) Widthwise 1100
4.2 and Table 1 x(Ash content )	-	950	Ash Content

31 Dec, 2026

-
For finished product

IS 14252 (2015)

Textiles – High density polyethylene (HDPE)/ polypropylene (PP) woven sack for filling sand – Specification (second revision)

19090 View breakup
Rs. 19,090/-, For BIS Samples Rs. 16,903/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Raw Material)	-	1050	Raw material Identification
3.2(Tapes – Width )	-	250	Width
3.2(Tapes – Linear Density )	-	500	Tapes – Linear Density
3.3(Tying Cord)	-	250	-
3.4(Sack)	-	250	-
3.4.1(Seam)	-	250	-
4.1 and Table 1 i a(Dimensions Outside Length)	-	250	-
4.1 and Table 1 i b(Dimensions Outside Width)	-	250.02	-
4.1 and Table 1 ii(Ends per dm )	-	250	-
4.1 and Table 1 iii(Picks per dm )	-	250	-
4.2 and Table 1 iv(Mass of sack )	-	250	-
4.1 and Table 1 v a(Average breaking strength of fabric Warpway )	-	1100	-
4.1 and Table 1 v b(Average breaking strength of fabric Weftway )	-	0	-
4.1 and Table 1 vi(Average Breaking strength of bottom seam )	-	1100	-
4.1 and Table 1 vii a(Elongation at break of fabric Lengthwise)	-	1100	-
4.1 and Table 1 vii b(Elongation at break of fabric Widthwise )	-	1100	-
4.1 and Table 1 viii(Average breaking strength and elongation at break of UV stabilized HDPE/PP fabric after been exposed to UV radiation and weathering )	-	1100	-
4.1 and Table 1 ix(Ash content )	-	950	-

31 Dec, 2026

-
For finished product

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

49525 View breakup
Rs. 49525/-; For BIS Samples : Rs. 31,869/- ; Raw Material : Rs. 5,825/-; For BIS Sample : Rs. 4,525/-; For Carbon Black Master Batch : Rs. 1,875/-; For BIS Sample : Rs. 1,406/-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 5.1 table-1(MATERIALS)	-	0	--
5.2(Polyethylene Resin)	-	1050	--
5.3 (a)(Carbon Black Master Batch)	-	1875	925+950
5.3(b)(Carbon Black Master Batch)	-	500	--
5.3(c)(Carbon Black Master Batch)	-	900	--
5.3(d)(Carbon Black Master Batch)	-	700	--
5.3(e)(Carbon Black Master Batch)	-	950	--
8.3(Carbon black)	-	925	--
8.6(Overall migration)	-	2000	1700+300
6, 6.1(PIPE DESCRIPTION)	-	0	--
6.2(Colour)	-	300	--
6.2.1(6.1.1 Identification Stripes)	-	250	--
7.2(Length)	-	250	--
7.4 table -3 & 4(6.1 Dimensions)	-	500	--
7.4.1.2(Ovality)	-	250	--
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	21400	100 hrs test=4000 48 hrs test =1600 165 hrs test =4800 1000 hrs test = 11000
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	1600	--
8.2(Longitudinal Reversion Test)	-	900	700+200
8.4( Melt Flow Rate)	-	1100	--
8.5 (Oxidation Induction Time)	-	2200	--
8.7(Density)	-	500	--
8.8(Tensile Strength for Butt-fusion)	-	1600	--
8.9 table-6(Elongation at Break)	-	1600	--
8.10(Slow Crack Growth Rate)	-	6000	5500+500

31 Dec, 2026

-
Size upto 400mm

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

19062.10 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Materials - shall be resistant to fertilizers and chemicals commonly employed in irrigation, and shall be suitable for use with water at temperatures up to 60°C and at pressures designed for the emitting pipe)	-	1050	--
5.1.2 (Ref. Cl 4.1.a of IS 12786 : 1989)(Potyethylene - higher olefins constituent )	-	1050	--
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	2000	--
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	1125	500+625
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	1000	--
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	700	--
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	925	--
5.1.2 (Ref. Cl 4.2.b of IS 12786 : 1989)(The dispersion of Carbon Black content shall be satisfactory - IS 2530 : 1963)	-	700	--
6.2.2(Fittings)	-	250	--
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	1000	--
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	1000	--
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	1000	--
8.2.1(Unregu/Qt~d Emining Pipe)	-	0	--
8.2.2(Regulated Emitting Pipes)	-	1000	--
8.3.1(Wall Thickness ofEmitting Pipe)	-	250	--
8.3.2(Inside Diameter ofEmitting Pipe)	-	250	--
8.3.3(Flow Paths in Emitting Unit)	-	200	--
8.3.4(Spacing ofEmitter Units)	-	200	--
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	1000	--
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	1600	--
8.5(Resistance to Tension at Elevated Temperature)	-	1100	--
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	400	--
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	1200	--
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	1600	--
8.8(Determination of Emitting Unit Exponent)	-	600	--
9.1(DESIGNATION - Non regulated Emitting Pipe)	-	0	--
9.2(DESIGNATION - Regulated Emitting Pipe)	-	0	--

31 Dec, 2026

-
-

IS 13487 (1992)

Irrigation equipment - Emitters - Specification

4700 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Construction and workmanship)	-	300	Construction & Workmanship
7.2(Flow path in emitters)	-	300	Flow Path in Emitter
7.3.1(Resistance to Hydrostatic pressure)	-	999.99	Resistance to Hydrostatic pressure
7.3.2(Resistance to Hydrostatic pressure)	-	0	included in 7.3.1
7.3.3(Resistance to Hydrostatic pressure)	-	0	included in 7.3.1
7.4.1(Emitter Pull Out In-line emitters)	-	500	Emitter Pullout
7.4.2(Emitter Pull Out On-line emitters)	-	0	Included in 7.4.1
8.1.2(Uniformity of Emission Rate Unregulated emitters)	-	1000	Uniformity of emission rate
8.1.3(Uniformity of Emission Rate Regulated emitters)	-	0	Included in 8.1.2
8.2.2(Emission rate as a function of inlet pressure Unregulated emitters)	-	1000	Emission rate as a function of inlet pressure
8.2.3(Emission rate as a function of inlet pressure Regulated emitters)	-	0	Included 8.2.2
8.3(Determination of Emitter Exponent)	-	600	Determination of Emitter Exponent

31 Dec, 2026

-
-

IS 12701 (1996)

Rotational moulded polyethylene water storage tanks - specification (First Revision)

11625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2.3(Carbon Black Content )	-	925	Carbon black content *
4.2.3(Carbon Dispersion Test)	-	700	Carbon black content
5(Types and Features )	-	3100	Net & Gross Capacity 500 Overall Diameter 250 Overall Height 250 Internal dia of man - hole 250 Wall thickness upon effective height 250 Wall thickness above effective height 250 Minimum weight without lid 500
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.1 Table 1(Dimensioas of Cylinderical Vertical Tank)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.2 Table 2(Dimensions of Rectangular Loft Tanks)	-	0	included in Types and feature
5.3(Types and Features )	-	0	included in Types and feature
5.6(Types and Features )	-	0	included in Types and feature
6.1(Finish)	-	300	Finish / Visual Appearance
7.1.1(Resistance to Deformation)	-	700	Resistance to deformation
7.1.2(Resistance to Deformation)	-	0	Resistance to deformation
7.2(Resistance to Impact)	-	1100	Resistance to impact
7.3(Test for Top Load Resistance)	-	900	Top load resistance (for 1500 lit and more)
7.4(Tensile Strength)	-	1100	Tensile Strength
7.5(Flexural Modulus)	-	1100	Flexural modulus
7.6(overall Migration)	-	1700	Overall Migration 40°C / Water/ 10 days

31 Dec, 2026

-
-

IS 7834 : Part 3 (1987)

injection moulded PVC socket fittings with solvent cement joints for water supplies: Part 3 Specific requirements for 90 degree elbows

7514 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
cl 2.2.2(Dimensions)	-	500	Dimension
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (first extraction) - Appendix C )	-	3000	Effect on water test
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Lead (third extraction) - Appendix C)	-	0	Effect on water test
Cl. 2.1 (Ref. Cl. 6.3 of IS 7834 (part 1) : 1987(Effect on water - Other toxic substances (third extraction) - Appendix C)	-	0	Effect on water test

31 Dec, 2026

-
-

IS 2508 (2016)

Polyethylene films and sheets - Specification (Third Revision)

20975 View breakup
For Black Films : Rs. 20,975/-, For BIS Samples Rs. 16,994/-; For Black Compound : Rs. 3,850/- , For BIS Samples Rs. 3,044/-; For Natural Films : Rs. 18,400/-, For BIS Samples Rs. 15,063/-; For Natural Compound : Rs. 2,225/- , For BIS Samples Rs. 1,825/-

31 Dec, 2026

-
-

Bureau of Indian Standards

The National Standards Body of India

CIPET: CENTRE FOR SKILLING AND TECHNICAL SUPPORT (CSTS) - AURANGABAD

Plot No. J-3/2, MIDC Industrial Area, Chikalthana, Jalgaon Road, Aurangabad - 431 006, AURANGABAD, Aurangabad, Maharashtra, 431006

8602677054 aurangabad@cipet.gov.in

Scope List