BIS - LIMS (Laboratory Information Management System)

Testtex India Laboratories Private Limited, Noida

C - 57, Sector - 65, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

9821318289 labsindianoida@testtex.com

Scope List

Reset

36 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 6721 (2023)

SANDAL AND SLIPPERS SPECIFICATION First revision

SANDAL AND SLIPPERS WITH AMENDMENT NO. 1

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.4(SHAPE AND DESIGN)	-	200	-
Cl. No.5("SIZE AND FITTINGS ")	-	200	-
Cl. No.6("CONSTRUCTION ")	-	200	-
Cl. No.7(MATERIAL)	-	200	-
Cl. No.8.1, Table no. 1(i),a("Tear strength, (other than moulded upper material) ")	-	500	-
Cl. No.8.1, Table no. 1(i),b("For all moulded upper material ")	-	500	-
Cl. No.8.1, Table no. 1(ii)(Flexing endurance)	-	1000	-
Cl. No.8.2,Table no. 2(i)(Tear strength)	-	500	-
Cl. No.8.2,Table no. 2(ii),a("Abrasion resistance- At dry condition")	-	1000	-
Cl. No.8.2,Table no. 2(ii),b("Abrasion resistance- At wet condition")	-	1000	-
Cl. No.8.3,Table no. 3(i)(Tear strength)	-	500	Tear - Leather, Tear - Non-leather
Cl. No.8.3,Table no. 3(ii),a("Abrasion resistance- At dry condition")	-	1000	-
Cl. No.8.3,Table no. 3(ii),b("Abrasion resistance- At wet condition")	-	1000	-
Cl. No.8.4,Table no. 4(i)(Grain crack index)	-	1000	-
Cl. No.8.4,Table no. 4(ii)(Density)	-	500	-
Cl. No.8.4,Table no. 4(iii)(Abrasion resistance)	-	1000	-
Cl. No.8.4,Table no. 5(i)(Density)	-	500	-
Cl. No.8.4,Table no. 5(ii)("Abrasion resistance, Volume loss ")	-	1000	-
Cl. No.8.4, Table no. 5(iii)("Flexing resistance, At 30 000 flexes")	-	1000	-
Cl. No.8.5, Table no. 6(i)("Bond strength, N/mm, Min (Applicable when fore part is fully covered or strap width is more than 25 mm)")	-	700	-
Cl. No.8.5, Table no. 6(ii)("Toe post attachment strength, N, Min (Applicable if toe post is present)")	-	500	-
Cl. No.8.5, Table no. 6(iii)("Toe ring attachment strength, Min (Applicable if toe ring is not integral part of upper")	-	500	-
Cl. No.8.5, Table no. 6(iv)(Strap to outsole strength)	-	500	-
Cl. No.8.5, Table no. 6(v)("Attachment strength of back strap and Buckle/D-ring ")	-	500	-
Cl. No.8.5, Table no. 6(vi)("Attachment strength of elastic, limit of useful extension, percent")	-	2000	-
Cl. No.8.5, Table no. 6(vii)("Attachment strength of back strap and velcro, N, Min (If, present)")	-	500	-
Cl. No.8.5, Table no. 6(viii)("Hydrolysis resistance, Cut growth after 150 000 flexes, mm, Max (Applicable for PU sole only)")	-	3500	-
Cl. No.8.5, Table no. 6(ix)("Heel pull off strength, N, Min (Applicable for heel height 40 mm and above attached separately to the sandal/slipper)")	-	1000	-
Cl. No.8.5, Table no. 6(x)("Inter layer bond strength, N/mm, (Applicable for multi-layer sole)")	-	700	-
Cl. No.8.6.1,Table 1 of IS 17011(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl. No.8.6.1,Table 1 of IS 17011(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl. No.8.("Requirement of Complete Sandal and Slipper (Chemical Requirements) ")	-	0	Refer Chemical Test Parameters
Cl. No.8.6.1,Table 1 of IS 17011(iv)(Chromium (VI))	-	750	-
Cl. No.8.6.1,Table 1 of IS 17011(v)(Dimethyl fumarate (DMFU))	-	3000	-
Cl. No.8.6.1,Table 1 of IS 17011(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl. No.8.6.1,Table 1 of IS 17011(vii)(Formaldehyde)	-	1000	-
Cl. No.8.6.1,Table 1 of IS 17011(viii)(Organotin compounds)	-	3000	-
Cl. No.8.6.1,Table 1 of IS 17011(ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
Cl. No.8.6.1,Table 1 of IS 17011(x)(pH)	-	500	-
Cl. No.8.6.1,Table 1 of IS 17011(xi)(Phthalates (each individual phthalate))	-	4000	-
Cl. No.8.6.1,Table 1 of IS 17011(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	5000	-
Cl. No.8.6.2(Lead content)	-	1000	-
Cl-5 ((Amendment No-1)(Category And Type)	-	500	-
Cl. No.9.(MARKING AND PACKING)	-	0	-
Cl. No.8.5, Table no. 6(xi)("Slip Resistance, Coefficient of Friction (COF) (Not applicable for leather sole) (To be carried out on quarry tiles)")	-	2000	-
Cl.8 Table-1 S.No 1, (ii) (Amendment No-1)(Toe post attachment strength)	-	500	-
Cl.8 Table-1 S.No 1, (iii) (Amendment No-1)(Toe ring attachment strength)	-	500	-
Cl.8 Table-1 S.No 1, (iv) (Amendment No-1)(Strap to outsole strength N, Min)	-	500	-
Cl.8 Table-1 S.No 1, (v) (Amendment No-1)(Attachment strength of back strap and buckle/D-ring N, Min)	-	500	-
Cl.8 Table-1 S.No 1, (vi) (Amendment No-1)(Limit of useful extension, percent, Min)	-	2000	-
Cl.8 Table-1 S.No 1, (vii) (Amendment No-1)(Attachment strength of back strap and velcro, N, Mi)	-	500	-
Cl.8 Table-1 S.No 1, (viii) (Amendment No-1)(Hydrolysis resistance)	-	3500	-
Cl.8 Table-1 S.No 1, (ix) (Amendment No-1)(Heel pull off strength)	-	1000	-
Cl.8 Table-1 S.No 1, (x) (Amendment No-1)(Inter layer bond strength)	-	700	-
Cl.8 Table-1 S.No 1, (xi) (Amendment No-1)(Slip resistance, coefficient of friction (COF)3)	-	2000	-
Cl.8 Table-1 S.No 1, (xii) (Amendment No-1)(Abrasion resistance, (volume loss) mm3 , Max)	-	1000	-
Cl.8 Table-1 S.No 1, (xiii) (Amendment No-1)("Flexing resistance (Belt method or Bennewart flex method)")	-	1000	-
Cl.8 Table-1 S.No 1, (xiv) (Amendment No-1)(Chemical Requirements)	-	26000	-
Cl.8 Table-1 S.No 1, (xv) (Amendment No-1)(Lead content (as Pb)7 ppm)	-	1000	Clause Repeated
Cl.9 Table-2 S.No 1, (i) a (Amendment No-1)(Tear strength for other than moulded upper material)	-	500	Clause Repeated
Cl.9 Table-2 S.No 1, (i) b (Amendment No-1)(Tear strength For all moulded upper material)	-	500	Clause Repeated
Cl.9 Table-2 S.No 1, (ii) (Amendment No-1)(Flexing endurance)	-	1000	Clause Repeated
Cl.9 Table-3 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	500	Clause Repeated
Cl.9 Table-3 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	2000	Clause Repeated
Cl.9 Table-4 S.No 1, (i) (Amendment No-1)(Tear strength, N, Min)	-	500	Clause Repeated
Cl.9 Table-4 S.No 1, (ii) (Amendment No-1)("Abrasion resistance (a) dry condition (b) wet condition")	-	2000	Clause Repeated
Cl.9 Table-5 S.No 1, (i) (Amendment No-1)(Grain crack index)	-	1000	-
Cl.9 Table-5 S.No 1, (ii) (Amendment No-1)(Density, g/cm3 , Min)	-	500	-
Cl.9 Table-5 S.No 1, (iii) (Amendment No-1)(Abrasion resistance, mm/kcs)	-	1000	-
Cl.9 Table-6 S.No 1, (i) (Amendment No-1)("Density, g/cm3 , Min (a)-Cellular, (b) Solid ")	-	500	-
Cl-10 (Amendment No-1)(Marking)	-	0	-
Cl.8 Table-1 S.No 1, (i) (Amendment No-1)(Bond strength , N/mm, Min)	-	700	-
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	500	Clause Repeated
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1000	Clause Repeated
Cl.8 - Table No 1 - Sl. No.-xiv(pH- IS 1390:2022)	-	500	Clause Repeated
Cl.8 - Table No 1 - Sl. No.-xv("Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988")	-	1000	Clause Repeated
Cl. No.8.6.1,Table 1 of IS 17011(i)(Allergenic and carcinogenic disperse dyes)	-	6000	-

-
-

IS 15844 : Part 1 (2023)

SPORTS FOOTWEAR PART -1 GENERAL PURPOSEFirst Revision

SPORTS FOOTWEAR PART -1 GENERAL PURPOSE + Amd. 1 : 2024

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
No Record Found

-
-

IS 15844 : Part 2 (2023)

SPORTS FOOTWEAR PART -2 PERFORMANCE SPORTS FOOTWEAR

PERFORMANCE SPORTS FOOTWEAR WITH AMENDMENT 1

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(SAMPLING AND CONDITIONING)	-	0	-
5(DESIGN)	-	200	-
6(SIZE AND FITTINGS)	-	500	-
7.1.1(Whole Footwear)	-	500	-
7.1.2(Upper to Mid Sole/Out Sole Bond Performance)	-	700	-
7.1.3("Upper to Composite Sole Bond Performance (Applicable Only When the Sole is Composite)")	-	700	-
7.1.4(Out Sole to Mid Sole (Multilayer) Bond Performance)	-	700	-
7.1.5(Energy Absorption at Seat Region)	-	1000	-
7.1.6(Complete Shoe Flexing)	-	1000	-
7.1.7(Washability)	-	1000	-
7.1.9(Heel Drop)	-	500	-
7.2 , Table No. 2 , i)(Flexing resistance)	-	1000	-
7.2 , Table No. 2 , ii)(Tear strength (average force))	-	500	-
7.2 , Table No. 2 , iii)("Colour fastness rubbing (To and fro) Grey scale rate Dry: (rubbing) Rating: (Marring and staining) ")	-	300	-
7.2 , Table No. 2 , iv) ,a)(Water vapour permeability)	-	1000	-
7.2 , Table No. 2 , iv) ,b)(Water vapour coefficient)	-	1000	-
7.2 , Table No. 2 , v)(Stitch tear strength (double hole))	-	700	-
7.2 , Table No. 2 , vi)("Colour fastness to light (Optional) Grey scale rate, Rating: (Marring)")	-	1000	-
7.2 , Table No. 2 , vii)(Tensile strength)	-	500	-
7.2 , Table No. 2 , viii)(Elongation at break,)	-	500	-
7.2 , Table No. 2 , ix)("Water penetration and water absorption after 60 Minutes Water absorption %, Max Water penetration Gms, Max")	-	1000	-
7.2 , Table No. 2 , x)(Abrasion test (for unlined upper))	-	1000	-
7.2 , Table No. 3 , i)(Breaking strength "As per Method 1 of IS 7016 (Part 2)/ ISO 1421 : 2016 or ISO 17706")	-	500	-
7.2 , Table No. 3 , ii)(Elongation at break)	-	500	-
7.2 , Table No. 3 , iii)(Tear strength, N, Min For Fabric: For all other materials)	-	500	-
7.2 , Table No. 3 , iv)(Strength at needle perforation)	-	700	-
7.2 , Table No. 3 , v)("Flexing resistance, no crack/damage to coating/ lamination / upper material till prescribed cycles")	-	1000	-
7.2 , Table No. 3 , vi) , a)(Water vapour permeability,)	-	1000	-
7.2 , Table No. 3 , vi) , b)("Water vapour coefficient, ")	-	1000	-
7.2 , Table No. 3 , vii)(Hydrolysis resistance)	-	3500	-
7.2 , Table No. 3 , viii)(Colour fastness to light grey scale rate)	-	1000	-
7.2 , Table No. 3 , ix)(Bursting Strength,)	-	500	-
7.3 , Table No. 4 , i)(Tear strength,)	-	500	-
7.3 , Table No. 4 , ii)(Abrasion resistance, cycles)	-	1000	-
7.3 , Table No. 4 , iii)("Colour fastness to rubbing (crocking), Grey scale rate with 10 rubs on dry or wet, ")	-	300	-
7.3 , Table No. 4 , iv)("Colour fastness to perspiration (contact method) Grey scale rate, ")	-	500	-
7.3 , Table No. 4 , v) , a)(Water vapour permeability,)	-	1000	-
7.3 , Table No. 4 , v) , b)("Water vapour coefficient, " As per IS 15298 (Part 1))	-	1000	-
7.4 , Table No. 5 , i)(Thickness)	-	200	-
7.4 , Table No. 5 , ii)(Flexing index)	-	1000	-
7.4 , Table No. 5 , iii)(Abrasion resistance, at 400 cycles)	-	300	-
7.4 , Table No. 5 , iv) , a)(Water Absorption,)	-	1000	-
7.4 , Table No. 5 , iv) , b)(Water Desorption)	-	1000	-
7.5 , Table No. 6 , i)(Thickness)	-	200	-
7.5 , Table No. 6 , ii)(Abrasion resistance, cycles As per IS 15298 (Part 1))	-	1000	-
7.5 , Table No. 6 , iii) , a)(Water Absorption)	-	1000	-
7.5 , Table No. 6 , iii) , b)(Water Desorption)	-	1000	-
7.5 , Table No. 6 , iv)(Heat resistance shrinkage linear)	-	500	-
7.6 , Table No. 7 , i)(Abrasion resistance (volume loss))	-	1000	-
7.6 , Table No. 7 , ii)(Flexing resistance)	-	1000	-
7.6 , Table No. 7 , iii)(Hydrolysis resistance, cut growth after 1 50 000 flexes)	-	3500	-
7.6 , Table No. 7 , iv)(Tear strength)	-	500	-
7.6 , Table No. 7 , v)(Tensile strength)	-	500	-
7.6 , Table No. 7 , vi)(Elongation at break)	-	500	-
7.6 , Table No. 7 , vii)(Compression set)	-	1000	-
7.7 , Table No. 8 , i)(Compression set)	-	1000	-
7.7 , Table No. 8 , ii)(Split tear strength,)	-	700	-
7.7 , Table No. 8 , iii)(Heat shrinkage,)	-	500	-
7.7 , Table No. 8 , iv)(Elongation at break,)	-	500	-
7.8 , Table No. 9 , i)(First dry collapsing load, hardness)	-	1000	-
7.8 , Table No. 9 , ii)(Resilience)	-	1000	-
7.8 , Table No. 9 , iii)(Moisture resistance)	-	1000	-
7.8 , Table No. 9 , iv) , a)(Initial dry area shape retention)	-	1000	-
7.8 , Table No. 9 , iv) , b)(Area shape retention after 10th collapse, dry)	-	1000	-
7.8 , Table No. 9 , v)(Peel strength)	-	1000	-
7.9 , Table No. 10 , i)(Peel strength)	-	1000	-
7.9 , Table No. 10 , ii)(Shear strength)	-	1000	-
7.10 , Table No. 11 , i)(Limit of useful extension,)	-	2000	-
7.10 , Table No. 11 , ii)(Needle strength,)	-	700	-
7.11 , Table No. 12 , i)(Breaking strength of lace,)	-	500	-
7.11 , Table No. 12 , ii)(Lace tag strength,)	-	500	-
7.11 , Table No. 12 , iii)(Lace to lace abrasion,)	-	1000	-
7.11 , Table No. 12 , iv)("Colour fastness to water Gray Scale Rate")	-	300	-
7.11 , Table No. 12 , v)(Strength of Buckle/Ski hook)	-	500	-
7.11 , Table No. 12 , vi)(Corrosion resistance)	-	500	-
7.12("Chemical Requirement on Complete Product for All Types of Sports Shoe")	-	0	Refer below
8(MARKING AND PACKING)	-	0	-
7.12, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
7.12, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
7.12, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	750	-
7.12, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	3000	-
7.12, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
7.12, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	1000	-
7.12, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	3000	-
7.12, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
7.12, Table no. 1 of IS 17011,(x)(pH)	-	1000	500/- Textile 500/- Leather
7.12, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	4000	-
7.12, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	5000	-
7.1.8(Slip Resistance)	-	2000	-
7.12.2 (Amendment 1)(Lead content)	-	1000	-
7.12, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	6000	-

-
-

IS 15844 : Part 3 (2024)

Sports Footwear Part 3 Professional Sports Footwear

42000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-6(Size and Fittings)	-	500	-
Cl-5(Design)	-	200	-
Cl-6(Size and Fittings)	-	500	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	700	-
Cl.7.1.2(Energy Absorption at Seat Region)	-	1000	-
Cl.7.1.1(Upper to Mid Sole/Out Sole, Upper to Composite Sole (Applicable Only When the Sole is Composite) and Out Sole to Mid Sole (Multilayer, if Present), Bond Performance)	-	700	-
Cl.7.1.2(Energy Absorption at Seat Region)	-	1000	-
Cl.7.1.3(Complete Shoe Flexing)	-	1000	-
Cl.7.1.4(Washability)	-	1000	-
Cl.7.1.5(Slip Resistance)	-	2000	-
Cl.7.1.6(Heel Drop)	-	500	-
Cl.7.2 Table-2 S.No- (i)("Flexing resistance, Min a) Dry condition b) Wet condition")	-	1000	-
Cl.7.2 Table-2 S.No- (ii)(Tear strength (average force), N, Min)	-	500	-
Cl.7.2 Table-2 S.No- (iii)("Colour fastness rubbing a-Dry b-Wet")	-	300	-
Cl.7.2 Table-2 S.No- (iv)("a) Water vapour permeability b) Water vapour coefficient")	-	1000	-
Cl.7.2 Table-2 S.No- (v)(Stitch tear strength N/mm, Min)	-	700	-
Cl.7.2 Table-2 S.No- (vi)(Colour fastness to light grey scale rate)	-	1000	-
Cl.7.2 Table-2 S.No- (vii)(Tensile strength)	-	500	-
Cl.7.2 Table-2 S.No- (viii)(Elongation at break, percent)	-	500	-
Cl.7.2 Table-2 S.No- (ix)("Abrasion test a) Dry b) Wet")	-	1000	-
Cl.7.2 Table-3 S.No- (i)(Breaking strength, N/mm, Min)	-	500	-
Cl.7.2 Table-3 S.No- (ii)(Elongation at break, percent, Min)	-	500	-
Cl.7.2 Table-3 S.No- (iii)(Tear strength, N, Min)	-	500	-
Cl.7.2 Table-3 S.No- (iv)(Strength at needle perforation)	-	700	-
Cl.7.2 Table-3 S.No- (v)("Flexing resistance a-Dry condition, b) Wet condition")	-	1000	-
Cl.7.2 Table-3 S.No- (vi)("a) Water vapour permeability b) Water vapour coefficient")	-	1000	-
Cl.7.2 Table-3 S.No- (vii)(Hydrolysis resistance)	-	3500	-
Cl.7.2 Table-3 S.No- (viii)(Colour fastness to light grey scale rate)	-	1000	-
Cl.7.2 Table-3 S.No- (ix)(Bursting strength)	-	500	-
Cl.7.3 Table-4 S.No- (i)(Tear strength, N, Min)	-	500	-
Cl.7.3 Table-4 S.No- (ii)("Abrasion resistance, a) Dry b) Wet ")	-	1000	-
Cl.7.3 Table-4 S.No- (iii)(Colour fastness to rubbing, grey scale rate with 10 rubs on dry or wet, Min)	-	300	-
Cl.7.3 Table-4 S.No- (iv)(Colour fastness to perspiration (contact method) grey scale rate, Min)	-	500	-
Cl.7.3 Table-4 S.No- (v)("a-Water vapour permeability b-Water vapour coefficient")	-	1000	-
Cl.7.4 Table-5 S.No- (i)(Flexing index, Min)	-	1000	-
Cl.7.4 Table-5 S.No- (ii)(Abrasion resistance)	-	500	-
Cl.7.4 Table-5 S.No- (iii)("a) Water absorption b) Water desorption")	-	1000	-
Cl.7.5 Table-6 S.No- (i)("Abrasion resistance a) Dry condition b) Wet condition")	-	1000	-
Cl.7.5 Table-6 S.No- (ii)("a) Water absorption b) Water desorption")	-	1000	-
Cl.7.5 Table-6 S.No- (iii)(Heat resistance shrinkage linear, percent, Max)	-	500	-
Cl.7.6 Table-7 S.No- (i)(Abrasion resistance)	-	1000	-
Cl.7.6 Table-7 S.No- (ii)("Flexing resistance a) Bennewart Method b) Ross flexing method")	-	1000	-
Cl.7.6 Table-7 S.No- (iii)(Hydrolysis resistance)	-	3500	-
Cl.7.6 Table-7 S.No- (iv)(Tear strength, N/mm, Min)	-	500	-
Cl.7.6 Table-7 S.No- (v)(Tensile strength)	-	500	-
Cl.7.6 Table-7 S.No- (vi)(Elongation at break percent, Min)	-	500	-
Cl.7.6 Table-7 S.No- (vii)(Compression set percent, Max)	-	1000	-
Cl.7.7 Table-8 S.No- (i)("Compression set, percent, Max a) For EVA b) For all other material")	-	1000	-
Cl.7.7 Table-8 S.No- (ii)(Split tear strength)	-	500	-
Cl.7.7 Table-8 S.No- (iii)(Heat shrinkage, percent, Ma)	-	500	-
Cl.7.7 Table-8 S.No- (iii)(Elongation at break, percent, Min)	-	500	-
Cl.7.7 Table-8 S.No- (iv)(Elongation at break, percent, Min)	-	500	-
Cl.7.8 Table-9 S.No- (i)(First dry collapsing load, hardness, N, Min)	-	1000	-
Cl.7.8 Table-9 S.No- (ii)(Resilience, percent, Min)	-	1000	-
Cl.7.8 Table-9 S.No- (iii)(Moisture resistance, percent, Min)	-	1000	-
Cl.7.8 Table-9 S.No- (iv)("a) Initial dry area shape retention, percent, Min b) Area shape retention after 10th collapse, dry, percent, Min ")	-	1000	-
Cl.7.8 Table-9 S.No- (v)(Peel strength, N/nm, Min)	-	1000	-
Cl.7.9 Table-10 S.No- (i)("Peel strength, N/mm, Min a) Initial b) After 5 000 wear cycles")	-	1000	-
Cl.7.9 Table-10 S.No- (ii)("Shear strength, kPa, Min a) Initial b) After 5 000 wear cycles")	-	1000	-
Cl.7.10 Table-11 S.No- (i)(Limit of useful extension, percent, Min)	-	2000	-
Cl.7.10 Table-11 S.No- (ii)(Needle strength, N/mm, Min)	-	700	-
Cl.7.11 Table-12 S.No- (i)(Breaking strength of lace)	-	500	-
Cl.7.11 Table-12 S.No- (ii)(Lace tag strength)	-	500	-
Cl.7.11 Table-12 S.No- (iii)(Lace to lace abrasion)	-	1000	-
Cl.7.11 Table-12 S.No- (iv)(Colour fastness to water (for lace) (Contact method))	-	300	-
Cl.7.11 Table-12 S.No- (v)(Strength of buckle/ski hook/D-ring,)	-	500	-
Cl.7.11 Table-12 S.No- (vi)("Corrosion resistance (applicable for all including decorative metal part) ")	-	500	-
Cl.7.11 Table-13 S.No- (i)(Corrosion resistance (applicable for metallic spikes))	-	500	-
Cl-7.12.1, Table no. 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	6000	-
Cl-7.12.1, Table no. 1 of IS 17011,(ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl-7.12.1, Table no. 1 of IS 17011,(iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	750	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	3000	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(vii)(Formaldehyde)	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	3000	-
Cl-7.12.1, Table no. 1 of IS 17011,(ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
Cl-7.12.1, Table no. 1 of IS 17011,(viii)(Organotin compounds)	-	3000	-
Cl-7.12.1, Table no. 1 of IS 17011,(vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl-7.12.1, Table no. 1 of IS 17011,(v)(Dimethyl fumarate (DMFU))	-	3000	-
Cl-7.12.1, Table no. 1 of IS 17011,(iv)(Chromium (VI))	-	750	-
Cl-7.12.1, Table no. 1 of IS 17011,(x)(pH)	-	500	-
Cl-7.12.1, Table no. 1 of IS 17011,(xi)(Phthalates (each individual phthalate))	-	4000	-
C-7.12.1, Table no. 1 of IS 17011,(xii)(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	5000	-
Cl-7.12.2(PVC is present in sports shoe)	-	1000	-
Cl- 8.1(Marking)	-	0	-

-
Included w.e.f. 07.04.2026

IS 17043 : Part 1 (2024)

Shoes - Specification Part 1 Shoes for Services

39000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.2(Design)	-	200	-
Cl-4.3.1(Size)	-	200	-
Cl-4.3.2(Weight)	-	200	-
Cl-4.4(Height of Upper)	-	200	-
Cl-4.5, S.Cl-4.5.2(Ergonomic Feature)	-	1000	-
Cl-4.5, S.Cl-4.5.3(Bond Strength)	-	0	Refer 4.5.3.1 & 4.5.3.2
Cl- 4.5.3.1(Upper-outsole bond strength)	-	700	-
Cl.4.5.3.2(Interlayer bond strength)	-	700	-
Cl-4.5, S.Cl-4.5.4(Slip Resistance)	-	2000	-
Cl-4.5.5.1(Electrical Properties-Antistatic footwear)	-	3500	-
Cl-4.5, S.Cl-4.5.6(Heat Insulation of Sole Complex)	-	1000	-
Cl-4.5, S.Cl-4.5.7(Cold Insulation of Sole Complex)	-	1000	-
Cl-4.6.1(Material)	-	200	-
Cl.4.5.8(Energy Absorption of Seat Region)	-	1000	-
Cl-4.6.2(Tear Strength)	-	500	-
Cl-4.6.3(Water Vapour Permeability and Coefficient)	-	1000	-
Cl-4.6.4(Water Penetration and Water Absorption)	-	1000	-
Cl-4.7.1(Material)	-	200	-
Cl-4.7.2(Tear Strength)	-	500	-
Cl-4.7.3(Abrasion Resistance)	-	1000	-
Cl-4.7.4(Water Vapour Permeability and Coefficient)	-	1000	-
Cl. 4.8.1(Material)	-	200	-
Cl-4.8.2(Abrasion Resistance)	-	500	-
Cl-4.8.3(Water Absorption and Desorption)	-	1000	-
Cl-4.9.2(Water Absorption and Desorption)	-	1000	-
4.9 Insocks(Insock thickness)	-	200	-
Cl-4.9.1(Material)	-	200	-
Cl-4.9.3(Abrasion Resistance)	-	1000	-
Cl-4.10(Toe Puff and Counter Stiffener)	-	200	-
Cl-4.11.1(Material)	-	200	-
Cl-4.11.2(Tear Strength)	-	500	-
Cl-4.12(Closing Thread)	-	500	-
Cl-4.13.3(Moulded Density)	-	500	-
Cl-4.13.4(Hardness)	-	500	-
Cl-4.13.5(Ageing Test)	-	700	-
Cl-4.13.6(Tear Strength)	-	500	-
Cl-4.13.7(Abrasion Resistance)	-	1000	-
Cl-4.13.8(Flexing Resistance)	-	1000	-
Cl-4.14(Eyelet)	-	1500	-
Cl-4.15.1(Material)	-	200	-
Cl-4.15.2(Breaking Load and Tag Retention)	-	1000	-
Cl-7(Marking)	-	0	-
Cl-5, Table 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	6000	-
Cl-5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl-5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl-5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	750	-
Cl-5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	3000	-
Cl-5, Table no 1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl-5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	1000	-
Cl-5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	3000	-
Cl-5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
Cl-5, Table no 1 of IS 17011 (x)(pH)	-	500	-
Cl-5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	4000	-
Cl-5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	5000	-
Cl-4.13.2(Thickness)	-	200	-
Cl-4.13.1(Material)	-	200	-
Cl-5(Chemical Requirements)	-	0	Refer individual chemical tests above

-
Included w.e.f. 04.11.2025

IS 15298 : part 4 (2024)

Personal Protective Equipment Part 4 Occupational Footwear (ISO 20347 : 2021, MOD) (Third Revision)

Occupational Footwear (Third Revision)

37500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	200	-
Cl 5.2.2(" Height of upper ")	-	200	-
Cl 5.2.3(Heel area)	-	200	-
Cl 5.3.1.1(Construction of whole footwear)	-	200	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	700	-
Cl 5.3.2(Leak proofness)	-	500	-
Cl 5.3.3(Specific ergonomic features)	-	1000	-
Cl 5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	2000	-
Cl 5.3.6(Seam strength)	-	500	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	200	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	200	-
Cl 5.4.2(Thickness)	-	200	-
Cl 5.4.3(Tear strength)	-	500	-
Cl 5.4.4, Table 9(Tensile properties- Tensile strength)	-	500	-
Cl 5.4.4, Table 9(Tensile properties- Breaking Force)	-	500	-
Cl 5.4.4, Table 9(Tensile properties-Modulus at 100 % elongation)	-	500	-
Cl 5.4.4, Table 9(Tensile properties- Elongation at break)	-	500	-
Cl 5.4.5(Flexing resistance)	-	1000	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	1000	-
Cl 5.4.7(Resistance to hydrolysis)	-	3500	-
Cl 5.5.2(Lining- Tear strength)	-	500	-
Cl 5.5.3(Lining- Abrasion resistance)	-	1000	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	1000	-
Cl 5.6.2(Tear strength of tongue)	-	500	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	200	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	1000	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	1000	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	500	-
Cl 5.8.2.1(Thickness of Outsole)	-	200	-
Cl 5.8.2.2(Cleated area)	-	200	-
Cl 5.8.2.3(Cleat height)	-	200	-
Cl 5.8.3(Outsole- Tear strength)	-	500	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	1000	-
Cl 5.8.5(Outsole-Flexing resistance)	-	1000	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	3500	-
Cl 5.8.7(Interlayer bond strength)	-	500	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	1000	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	1000	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	1000	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	200	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	200	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	1000	-
Cl 6.2.1.4.2.1(ISO 20344:2021, 5.11.2)	-	500	-
Cl 6.2.1.4.2.2(ISO 20344:2021, 5.6.2.1)	-	500	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	3000	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	3500	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	3500	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1000	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1000	-
Cl 6.2.4(Energy absorption of seat region)	-	1000	-
Cl 6.2.5(Water resistance)	-	1000	-
Cl 6.2.7.1(Cut resistance footwear- design)	-	200	-
Cl 6.2.7.2(Dimensions and construction of protective area of Cut resistance footwear)	-	200	-
Cl 6.2.7.3(Resistance to cutting)	-	4000	-
Cl 6.2.8(Scuff cap)	-	1000	-
Cl 6.2.9("Slip resistance on ceramic tile floor with glycerine ")	-	2000	-
Cl 6.3(Upper — Water penetration and absorption)	-	1000	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	1000	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1000	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	500	-
Cl 6.4.3.2(Design of Ladder grip)	-	200	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	200	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	200	-
Cl 7("Marking ")	-	0	-
Cl 5.3.5, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	6000	-
Cl 5.3.5, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl 5.3.5, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl 5.3.5, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	750	-
Cl 5.3.5, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	3000	-
Cl 5.3.5, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl 5.3.5, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	1000	-
Cl 5.3.5, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	3000	-
Cl 5.3.5, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
Cl 5.3.5, Table no 1 of IS 17011 (x)(pH)	-	500	-
Cl 5.3.5, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	4000	-
Cl 5.3.5, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	5000	-
Cl 5.3.7(Lead Content ( National Annex A))	-	1000	-
Cl.1.4.1 of IS 17011 (Table B Sl I )(Phthalate: DINP)	-	0	Repeated Clause
Cl.1.4.1 of IS 17011 (Table B Sl II )(Phthalate:: DNOP)	-	0	Repeated Clause
Cl.1.4.1 of IS 17011 (Table B Sl III )(Phthalate: DEHP)	-	0	Repeated Clause
Cl.1.4.1 of IS 17011 (Table B Sl IV )(Phthalate: DIDP)	-	0	Repeated Clause
Cl.1.4.1 of IS 17011 (Table B Sl V)(Phthalate: BBP)	-	0	Repeated Clause
Cl.1.4.1 of IS 17011 (Table B Sl VI )(Phthalate:DBP)	-	0	Repeated Clause
Cl.1.4.1 of IS 17011 (Table B Sl VII )(Phthalate: DIBP)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl I )(Organotin: Dibutyltin)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl II )(Organotin: Dibutyltin Dichloride)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl III )(Organotin: Dioctyltin)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl IV)(Organotin: Monobutyltin)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl V )(Organotin: Tributyltin)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl VI)(Organotin: Triphenyltin)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl VII )(Organotin: Monoctyltin)	-	0	Repeated Clause
Cl.4.1 (Annex-A Sl VIII)(Organotin: Bis (tributyltin) oxide)	-	0	Repeated Clause
Cl. No.8.6.1,Table 1 of IS 17011(Chromium)	-	0	Repeated Clause
Cl. No.8.6.1,Table 1 of IS 17011(Formaldehyde (free or released by partial hydrolysis))	-	0	Repeated Clause
Cl. No.8.6.1,Table 1 of IS 17011(Nickel, on skin contact 2-(thiocyanomethylthio) -benzothiazole (TCMTB))	-	0	Repeated Clause
Cl.8 - Table No 1(Lead Content (as Pb) (applicable for PVC only) - IS 12240 (Part 5) : 1988)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl I)(Allergenic Disperse Dyes :Disperse blue 3)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl II)(Allergenic Disperse Dyes :Disperse blue 7)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl III)(Allergenic Disperse Dyes :Disperse blue 26)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl IV)(Allergenic Disperse Dyes :Disperse blue 102)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl V)(Allergenic Disperse Dyes: Disperse brown 1)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl VI)(Allergenic Disperse Dyes :Disperse yellow 1)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl VII)(Allergenic Disperse Dyes :Disperse yellow 9)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl VIII)(Allergenic Disperse Dyes :Disperse yellow 39)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl IX)(Allergenic Disperse Dyes :Disperse yellow 49)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl X)(Allergenic Disperse Dyes :Disperse orange 1)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl XI)(Allergenic Disperse Dyes :Disperse red 11)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl XII)(Allergenic Disperse Dyes :Disperse red 17)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl XIII)(Allergenic Disperse Dyes :Disperse yellow 7)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl XIV)(Allergenic Disperse Dyes :Disperse yellow 56)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl XV)(Allergenic Disperse Dyes :Disperse red 151)	-	0	Repeated Clause
Cl.4.1 (Table B-3 Sl XVI)(Allergenic Disperse Dyes :Solvent red 23)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl I)(Carcinogenic Disperse Dyes :Navy blue)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl II)(Carcinogenic Disperse Dyes: Disperse blue 1)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl III)(Carcinogenic Disperse Dyes: Disperse blue 35)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl IV)(Carcinogenic Disperse Dyes :Disperse blue 106)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl V)(Carcinogenic Disperse Dyes: Disperse blue 124)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl VI)(Carcinogenic Disperse Dyes :Disperse yellow 3)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl VII)(Carcinogenic Disperse Dyes: Disperse orange 3)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl VIII)(Carcinogenic Disperse Dyes :Disperse orange 37/59/76a))	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl IX)(Carcinogenic Disperse Dyes :Disperse red 1)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl X)(Carcinogenic Disperse Dyes :Basic red 9)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl XI)(Carcinogenic Disperse Dyes :Violet 3)	-	0	Repeated Clause
Cl.4.1 (Table B-4 Sl XII)(Carcinogenic Disperse Dyes Disperse :yellow 23)	-	0	Repeated Clause
Cl 5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution (ii))	-	0	Repeated Clause
Cl 5.7.2(Water permeability of insock)	-	0	Repeated Clause

-
Included w.e.f. 04.11.2025 Exclusion: Cl 6.2.6 (Ankle protection)

IS 15298 : Part 3 (2024)

Personal Protective Equipment Part 3 Protective Footwear (ISO 20346 : 2021, MOD) (Third Revision)

Protective Footwear (Third Revision)

39000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	200	-
Cl 5.2.2(" Height of upper ")	-	200	-
Cl 5.2.3(Heel area)	-	200	-
Cl 5.3.1.1(Construction of whole footwear)	-	200	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	700	-
Cl 5.3.2.1(Toe protection - general)	-	200	-
Cl 5.3.2.2(Internal length)	-	200	-
Cl 5.3.2.3(Width of toecap flange)	-	200	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	500	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	500	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	3000	-
Cl 5.3.2.6(Impact resistance)	-	1000	-
Cl 5.3.2.7(Compression resistance)	-	1000	-
Cl 5.3.3(Leak proofness)	-	500	-
Cl 5.3.4("Specific ergonomic features ")	-	500	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	2000	-
Cl 5.3.7(Seam strength)	-	500	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	200	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	200	-
Cl 5.4.2(Thickness)	-	200	-
Cl 5.4.3(Tear strength)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	500	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	500	-
Cl 5.4.5(Flexing resistance)	-	1000	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	1000	-
Cl 5.4.7(Resistance to hydrolysis)	-	3500	-
Cl 5.5.2(Lining- Tear strength)	-	500	-
Cl 5.5.3(Lining- Abrasion resistance)	-	1000	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	1000	-
Cl 5.6.2(Tear strength of tongue)	-	500	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	200	-
Cl 5.7.2(Water permeability of insock)	-	1000	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	1000	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	500	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	1000	-
Cl 5.8.2.1(Thickness of Outsole)	-	200	-
Cl 5.8.2.2(Cleated area)	-	200	-
Cl 5.8.2.3(Cleat height)	-	200	-
Cl 5.8.3(Outsole- Tear strength)	-	500	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	1000	-
Cl 5.8.5(Outsole-Flexing resistance)	-	1000	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	3500	-
Cl 5.8.7(Interlayer bond strength)	-	500	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	1000	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	1000	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	1000	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	200	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	200	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	1000	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	500	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	500	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	3000	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	3500	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	3500	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1000	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1000	-
Cl 6.2.4(Energy absorption of seat region)	-	1000	-
Cl 6.2.5(Water resistance)	-	1000	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	200	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	2000	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	200	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	4000	-
Cl 6.2.8.3(Resistance to cutting)	-	4000	-
Cl 6.2.9(Scuff cap)	-	1000	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	2000	-
Cl 6.3(Upper — Water penetration and absorption)	-	1000	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	1000	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1000	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	500	-
Cl 6.4.3.2(Design of Ladder grip)	-	200	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	200	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	200	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	6000	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	750	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	3000	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	3000	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	500	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	4000	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	5000	-
Cl 5.3.8(Lead Content ( National Annex A))	-	1000	-
Cl 7("Marking ")	-	0	-
Cl 7("Marking ")	-	0	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	0	repeated clause.
Cl 5.2(Design)	-	-	-
Cl 5.2.2(" Height of upper ")	-	-	-
Cl 5.2.3(Heel area)	-	-	-
Cl 5.3.1.1(Construction of whole footwear)	-	-	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	-	-
Cl 5.3.2.1(Toe protection - general)	-	-	-
Cl 5.3.2.2(Internal length)	-	-	-
Cl 5.3.2.3(Width of toecap flange)	-	-	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	-	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	-	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	-	-
Cl 5.3.2.6(Impact resistance)	-	-	-
Cl 5.3.2.7(Compression resistance)	-	-	-
Cl 5.3.3(Leak proofness)	-	-	-
Cl 5.3.4("Specific ergonomic features ")	-	-	-
Cl 5.3.5.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	-	-
Cl 5.3.7(Seam strength)	-	-	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	-	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	-	-
Cl 5.4.2(Thickness)	-	-	-
Cl 5.4.3(Tear strength)	-	-	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	-	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	-	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-	-
Cl 5.4.5(Flexing resistance)	-	-	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	-	-
Cl 5.4.7(Resistance to hydrolysis)	-	-	-
Cl 5.5.2(Lining- Tear strength)	-	-	-
Cl 5.5.3(Lining- Abrasion resistance)	-	-	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	-	-
Cl 5.6.2(Tear strength of tongue)	-	-	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	-	-
Cl 5.7.2(Water permeability of insock)	-	-	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	-	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	-	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	-	-
Cl 5.8.2.1(Thickness of Outsole)	-	-	-
Cl 5.8.2.2(Cleated area)	-	-	-
Cl 5.8.2.3(Cleat height)	-	-	-
Cl 5.8.3(Outsole- Tear strength)	-	-	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	-	-
Cl 5.8.5(Outsole-Flexing resistance)	-	-	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	-	-
Cl 5.8.7(Interlayer bond strength)	-	-	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	-	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	-	-
Cl 6.2.1.1.4(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	-	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	-	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	-	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	-	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	-	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	-	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	-	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	-	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	-	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	-	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	-	-
Cl 6.2.4(Energy absorption of seat region)	-	-	-
Cl 6.2.5(Water resistance)	-	-	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	-	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	-	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	-	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	-	-
Cl 6.2.8.3(Resistance to cutting)	-	-	-
Cl 6.2.9(Scuff cap)	-	-	-
Cl 6.2.10("Slip resistance on ceramic tile floor with glycerine ")	-	-	-
Cl 6.3(Upper — Water penetration and absorption)	-	-	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	-	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	-	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	-	-
Cl 6.4.3.2(Design of Ladder grip)	-	-	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	-	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (i)(Allergenic and carcinogenic disperse dyes)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	-	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	-	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	-	-
Cl 5.3.8(Lead Content ( National Annex A))	-	-	-
Cl 7("Marking ")	-	-	-
Cl 7("Marking ")	-	-	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	-	-

-
Included w.e.f 11.09.2025 Exclusion: Cl 6.2.7 (Ankle protection)

IS 15298 : Part 2 (2024)

Personal Protective Equipment Part 2 Safety Footwear (ISO 20345 : 2021, MOD) (Third Revision)

Safety Footwear

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.2(Design)	-	200	-
Cl 5.2.2, Table 4(" Height of upper ")	-	200	-
Cl 5.2.3(Heel area)	-	200	-
Cl 5.3.1.1(Construction of whole footwear)	-	200	-
Cl 5.3.1.2(Upper/outsole bond strength)	-	700	-
Cl 5.3.2.1(Toe protection - general)	-	200	-
Cl 5.3.2.2(Internal length)	-	200	-
Cl 5.3.2.3(Width of toecap flange)	-	200	-
Cl 5.3.2.4.1(Corrosion resistance of Class I footwear and hybrid mounted footwear)	-	500	-
Cl 5.3.2.4.2(Corrosion resistance of Class II and hybrid moulded footwear)	-	500	-
Cl 5.3.2.5(Behaviour of toecaps (thermal and chemical) of Corrosion resistance)	-	3000	-
Cl 5.3.2.6(Impact resistance)	-	1000	-
Cl 5.3.2.7(Compression resistance)	-	1000	-
Cl 5.3.3(Leak proofness)	-	500	-
Cl 5.3.4("Specific ergonomic features ")	-	1000	-
Cl 5.3.5.2, Table 7(Slip resistance on ceramic tile floor with sodium lauryl sulphate (NaLS) solution)	-	2000	-
Cl 5.3.7(Seam strength)	-	500	-
Cl 5.4.1.1(Class I footwear, determination of the area where upper requirements apply of Upper)	-	200	-
Cl 5.4.1.2(Hybrid footwear, determination of the area where upper requirements apply of Upper)	-	200	-
Cl 5.4.2(Thickness)	-	200	-
Cl 5.4.3(Tear strength)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Tensile strength)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Breaking Force)	-	500	-
Cl 5.4.4, Table 11(Tensile properties-Modulus at 100 % elongation)	-	500	-
Cl 5.4.4, Table 11(Tensile properties- Elongation at break)	-	500	-
Cl 5.4.5(Flexing resistance)	-	1000	-
Cl 5.4.6(Water vapour permeability and coefficient)	-	1000	-
Cl 5.4.7(Resistance to hydrolysis)	-	3500	-
Cl 5.5.2(Lining- Tear strength)	-	500	-
Cl 5.5.3(Lining- Abrasion resistance)	-	1000	-
Cl 5.5.4(Lining-Water vapour permeability and coefficient)	-	1000	-
Cl 5.6.2, Table 14(Tear strength of tongue)	-	500	-
Cl 5.7.1(Thickness of Insole, insock and footbed)	-	200	-
Cl 5.7.2(Water permeability of insock)	-	1000	-
Cl 5.7.3(Water absorption and desorption of Insole, insock and footbed)	-	1000	-
Cl 5.7.4.1(Abrasion resistance of Insoles)	-	500	-
Cl 5.7.4.2(Abrasion resistance of Insocks)	-	1000	-
Cl 5.8.2.1, Table 15(Thickness of Outsole)	-	200	-
Cl 5.8.2.2(Cleated area)	-	200	-
Cl 5.8.2.3(Cleat height)	-	200	-
Cl 5.8.3(Outsole- Tear strength)	-	500	-
Cl 5.8.4(Outsole- Abrasion resistance)	-	1000	-
Cl 5.8.5(Outsole-Flexing resistance)	-	1000	-
Cl 5.8.6(Outsole-Resistance to hydrolysis)	-	3500	-
Cl 5.8.7(Interlayer bond strength)	-	500	-
Cl 6.2.1.1.2(Metallic perforation-resistant inserts (Type P))	-	1000	-
Cl 6.2.1.1.3(Non-metallic perforation-resistant inserts and insoles (Type PL))	-	1000	-
Personal protective equipment: Part 2 safety footwear(Non-metallic perforation-resistant inserts and insoles (Type PS))	-	1000	-
Cl 6.2.1.2(Construction of perforation resistant insert)	-	200	-
Cl 6.2.1.3(Dimensions of perforation resistant insert)	-	200	-
Cl 6.2.1.4.1(Flex resistance of perforation-resistant inserts)	-	1000	-
Cl 6.2.1.4.2.1(Corrosion resistance of perforation resistant metallic insert for Class I footwear and hybrid mounted footwear)	-	500	-
Cl 6.2.1.4.2.2(Corrosion resistance of perforation resistant metallic insert for Class II footwear and hybrid moulded footwear)	-	500	-
Cl 6.2.1.4.3(Stability against ageing and environmental influence of non-metallic perforationresistant inserts)	-	3000	-
Cl 6.2.2.1(Electrical properties of Partially conductive footwear)	-	3500	-
Cl 6.2.2.2(Electrical properties of Antistatic footwear)	-	3500	-
Cl 6.2.3.1(Heat insulation of outsole complex)	-	1000	-
Cl 6.2.3.2(Cold insulation of outsole complex)	-	1000	-
Cl 6.2.4(Energy absorption of seat region)	-	1000	-
Cl 6.2.5(Water resistance)	-	1000	-
Cl 6.2.6.1(Metatarsal protection - Construction)	-	200	-
Cl 6.2.6.2("Metatarsal protection-Impact resistance of metatarsal protective device ")	-	2000	-
Cl 6.2.8.2(Cut resistance footwear- design)	-	200	-
Cl 6.2.8.3(Resistance to cutting)	-	4000	-
Cl 6.2.9(Scuff cap)	-	1000	-
Cl 6.2.10 , Table 19("Slip resistance on ceramic tile floor with glycerine ")	-	2000	-
Cl 6.3(Upper — Water penetration and absorption)	-	1000	-
Cl 6.4.1(Resistance to hot contact - Outsole)	-	1000	-
Cl 6.4.2(Resistance to fuel oil - Outsole)	-	1000	-
Cl 6.4.3.1(Mechanical properties of Ladder grip)	-	500	-
Cl 6.4.3.2(Design of Ladder grip)	-	200	-
Cl 6.4.3.3(Cleat height in the waist area of Ladder grip)	-	200	-
Cl 6.4.3.4(Heel breast of Ladder grip)	-	200	-
Cl 6.2.8.2(Dimensions and construction of protective area of Cut resistance footwear)	-	200	-
Cl 5.3.6, Table no 1 of IS 17011 (ii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl 5.3.6, Table no 1 of IS 17011 (iii)(Aromatic amines released from Azo dyes (each individual amine))	-	2000	-
Cl 5.3.6, Table no 1 of IS 17011 (iv)(Chromium (VI))	-	750	-
Cl 5.3.6, Table no 1 of IS 17011 (x)(pH)	-	500	-
Cl 5.3.6, Table no 1 of IS 17011 (xii)(Nickel, on skin contact)	-	5000	-
Cl 5.3.6, Table no 1 of IS 17011 (v)(Dimethyl fumarate (DMFU))	-	3000	-
Cl 5.3.6, Table no1 of IS 17011 (vi)(Formaldehyde (free or released by partial hydrolysis))	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011 (vii)(Formaldehyde)	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011 (viii)(Organotin compounds)	-	3000	-
Cl 5.3.6, Table no 1 of IS 17011 (ix)(PCP-TeCP-TriCP polychlorophenols)	-	3000	-
Cl 5.3.6, Table no 1 of IS 17011 (xi)(Phthalates (each individual phthalate))	-	4000	-
Cl 5.3.8(Lead Content ( National Annex A))	-	1000	-
Cl 5.3.6, Table no 1 of IS 17011,(i)(Allergenic and carcinogenic disperse dyes)	-	6000	-
Cl 7, Table 20("Marking ")	-	0	-

-
Included w.e.f 12.09.2025 Exclusion: Cl 6.2.7 (Ankle protection)

IS 9873 : Part 1 (2019)

Safety of toys: Part 1 safety aspects related to mechanical and physical properties (Fourth Revision)

All

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.2 - 5.24.2( Reasonably foreseeable abuse -Drop Test)	-	100	-
4.2 - 5.24.3( Reasonably foreseeable abuse -Tip-over test for large and bulky toys)	-	200	-
4.2 - 5.24.4( Reasonably foreseeable abuse -Dynamic strength test for wheeled ride-on toys other than toy scooters)	-	400	-
4.2 - 5.24.5( Reasonably foreseeable abuse -Torque test)	-	200	-
4.2 - 5.24.6.2( Reasonably foreseeable abuse -Tension test for seams in soft-filled (stuffed) toys. beanbag-type toys, and other similar filled toys)	-	200	-
4.2 - 5.24.6.3( Reasonably foreseeable abuse -Tension test for pompoms)	-	200	-
4.2 - 5.24.6.4( Reasonably foreseeable abuse -Tension test for protective components)	-	200	-
4.2 - 5.24.6.5( Reasonably foreseeable abuse -Tension test for a projectile with a suction cup)	-	200	-
4.2 - 5.24.7( Reasonably foreseeable abuse -Compression test)	-	300	-
4.2 - 5.24.8.2( Reasonably foreseeable abuse-Flexure test-Wires and other metallic components intended to be bent)	-	400	-
4.2 - 5.24.8.3( Reasonably foreseeable abuse -Flexure test-Wires likely to be bent)	-	500	-
4.3.2 - 5.21( Expanding materials)	-	500	-
4.4.1 - 5.2(Small parts-For children under 36 months)	-	200	-
4.4.2 - 5.2(Small parts-For children 36 months and over but under 72 months )	-	200	-
4.5.1.2 - 5.3(Shape, size and strength of certain toys-Squeeze toys, rattles, and certain other toys and components of toys-Test for shape and size of certain toys)	-	200	-
4.5.1.3 - 5.3(Shape, size and strength of certain toys-Other toys or components of toys with nearly spherical, hemispherical, circular flared, or dome-shaped ends of toys having a mass less than 0,5 kg and intended for children under 18 months-Test for shape and size of certain toys)	-	200	-
4.5.1.4 - 5.3(Shape, size and strength of certain toys-Toy fasteners (e.g. nails, bolts, screws, and pegs) with nearly spherical, hemispherical, or dome-shaped ends intended for children 18 months and over but under 48 months-Test for shape and size of certain toys)	-	200	-
4.5.2 - 5.4(Shape, size and strength of certain toys-Small balls-Small balls test)	-	200	-
4.5.3 - 5.5(Shape, size and strength of certain toys-Pompoms-Test for pompoms)	-	200	-
4.5.4 - 5.6(Shape, size and strength of certain toys- Pre-school play figures-Test for pre-school play figures)	-	200	-
4.5.5(Shape, size and strength of certain toys-Toy pacifiers-Nipple length)	-	200	-
4.5.6(Shape, size and strength of certain toys-Balloons)	-	300	-
4.5.7(Shape, size and strength of certain toys-Marbles)	-	200	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-No of Opening)	-	200	-
4.5.8 - a(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening not in Base)	-	200	-
4.5.8 - b(Shape, size and strength of certain toys-Hemispheric-shaped toys-Extension of divider)	-	200	-
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening )	-	200	-
4.5.8 - c(Shape, size and strength of certain toys-Hemispheric-shaped toys-Position of opening )	-	200	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys)	-	200	-
4.5.8 - d(Shape, size and strength of certain toys-Hemispheric-shaped toys-Minimum depth)	-	200	-
4.6.1 a - 5.8(Edges-Accessible sharp edges of glass or metal-Sharp edge test)	-	400	-
4.6.1 b(Edges-Accessible sharp edges of glass or metal- gap between the edge and the adjacent surface)	-	300	-
4.6.2(Edges-Functional sharp edges)	-	300	-
4.6.3 - 5.8(Edges-Edges on metal toys-Sharp edge test)	-	400	-
4.6.4( Edges-Edges on moulded toys)	-	300	-
4.6.5( Edges-Edges on exposed bolts or threaded rod)	-	300	-
4.7.1 - 5.9(Points-Accessible sharp points-sharp-point test)	-	400	-
4.7.2 - a(Points-Functional sharp points)	-	300	-
4.7.2 - b(Points-Functional sharp points)	-	300	-
4.7.3 (Wooden toys)	-	300	-
4.8.1(Projections-General requirments)	-	300	-
4.9(a) - 5.24.8.2( Metal wires and rods-wires and other metallic components intended to be bent)	-	300	-
4.9(b) - 5.24.8.3( Metal wires and rods-wires likely to be bent)	-	300	-
4.9 - c( Metal wires and rods)	-	300	-
4.9 - c - 5.8( Metal wires and rods-Sharp edge test)	-	400	-
4.9 - c - 5.9( Metal wires and rods-Sharp Point test)	-	400	-
4.9 - c( Metal wires and rods-Minimum dia of spokes)	-	300	-
4.9 - c( Metal wires and rods-Spokes ends)	-	300	-
4.10(a) - 5.10(Plastic film or plastic bags in packaging and in toys-average thickness)	-	400	-
4.11.2.1(a) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	200	-
4.11.2.1(b) - 5.11.3( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-breakaway feature separation test)	-	300	-
4.11.2.1(b) - 5.11.2( Cords-Cords in toys intended for children under 18 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test)	-	300	-
4.11.2.2 - 5.11.2( Cords-Cords in toys intended for children under 18 months--Other cords-free length )	-	300	-
4.11.3.1(a) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables)	-	300	-
4.11.3.1(b) - 5.11.3( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-breakaway feature separation test)	-	300	-
4.11.3.1(b) - 5.11.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Cords with the potential to tangle-Length of cords and electrical cables after breakaway feature separation test)	-	300	-
4.11.3.2( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords)	-	300	-
4.11.3.3 ( Cords-Cords in toys intended for children 18 months and over but under 36 months-Other cords without a free end )	-	300	-
4.11.4(a) - 5.11.4.1(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Head probe push test)	-	300	-
4.11.4(a) - 5.11.4.2(Cords-Fixed loops and nooses intended for children under 36 months-Test for fixed loops and nooses-Elastic materials)	-	300	-
4.12.1(a - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	300	-
4.12.1(a - 2)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	300	-
4.12.1(a - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators)	-	400	-
4.12.1(a - 4)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	300	-
4.12.1(a - 5) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	400	-
4.12.1(b - 1)(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	300	-
4.12.1(b - 2) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.1(b - 3) - 5.22.2(Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	500	-
4.12.2 (a) - 5.22.3(Folding mechanisms-Other toys with folding mechanisms)	-	300	-
4.12.3(Folding mechanisms-Hinge line clearance)	-	400	-
4.13.1(Holes, clearances and accessibility of mechanisms-Circular holes in rigid materials)	-	300	-
4.13.2 (Holes, clearances and accessibility of mechanisms-Accessible clearances for movable segments)	-	300	-
4.13.3(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys)	-	300	-
4.13.3 - 5.7(Holes, clearances and accessibility of mechanisms- Chains or belts in ride-on toys-accessibility of a part or component)	-	300	-
4.13.4(Holes, clearances and accessibility of mechanisms-Other driving mechanisms)	-	300	-
4.13.5(Holes, clearances and accessibility of mechanisms-Winding keys)	-	300	-
4.14(a)(Springs)	-	300	-
4.14(b)(Springs)	-	300	-
4.14(c)(Springs)	-	300	-
4.15.1.1 - 5.12.2( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet available for stabilization)	-	400	-
4.15.1.2 - 5.12.3( Stability and overload requirements-Stability of ride-on toys and seats-Sideways stability, feet unavailable for stabilization)	-	500	-
4.15.1.3 - 5.12.4( Stability and overload requirements-Stability of ride-on toys and seats-Fore and aft stability Test)	-	500	-
4.15.2 - 5.12.5( Stability and overload requirements-Overload requirements for ride-on toys and seats-overload test for ride-on toys and seats)	-	500	-
4.15.2 - 5.24.4( Stability and overload requirements-Overload requirements for ride-on toys and seats-dynamic strength test for wheeled ride-on toys other than toy scooters)	-	500	-
4.15.3 - 5.12.6( Stability and overload requirements-Stability of stationary floor toy-Stability test of stationary floor toys)	-	500	-
4.16.1(Enclosures-Ventilation)	-	400	-
4.16.1(Enclosures-Ventilation-No of openings)	-	400	-
4.16.1(Enclosures-Ventilation-Area of Each openings(If two openings))	-	400	-
4.16.1(Enclosures-Ventilation-Distance between openings(If two openings))	-	400	-
4.16.1(Enclosures-Ventilation-Area of Each openings(If One opening))	-	400	-
4.16.1(Enclosures-Ventilation-spacing(If One opening))	-	400	-
4.16.2.1(Enclosures-Closures-Lids, doors and similar devices)	-	400	-
4.16.2.1 - 5.13.1(Enclosures-Closures-Lids, doors and similar devices-Test For closures)	-	600	-
4.16.2.2(a)(Enclosures-Closures-Lid support for toy chests and similar toys)	-	400	-
4.16.2.2(a) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys- After durability test for toy chest lids)	-	2300	-
4.16.2.2(a) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys-Test For lid support After durability test for toy chest lids)	-	2300	-
4.16.2.2(b) - 5.13.2.2(Enclosures-Closures-Lid support for toy chests and similar toys-durability test for toy chest lids)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 1)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 2)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 3) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys-toy pushchairs and perambulators)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 4)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(a - 5) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 1)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 2) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.1(b - 3) - 5.22.2(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Toy pushchairs, perambulators and similar toys)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.2 (a) - 5.22.3(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Other toys with folding mechanisms)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.2 (b)(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Other toys with folding mechanisms)	-	2300	-
4.16.2.2(c) - 5.13.2.2 - 4.12.3(Enclosures-Closures-Lid support for toy chests and similar toys-Folding mechanisms-Hinge line clearance)	-	2300	-
4.16.2.2(d)(Enclosures-Closures-Lid support for toy chests and similar toys)	-	400	-
4.16.3(Enclosures-Toys that enclose the head)	-	400	-
4.17 - 5.14(Simulated protective equipment, such as helmets, hats and goggles-Impact test for toys that cover the face)	-	600	-
4.17(Simulated protective equipment, such as helmets, hats and goggles)	-	400	-
4.18.2(a) - 5.36(Projectile toys-Projectiles-tip assessment of rigid projectiles)	-	1100	-
4.18.2(b)(Projectile toys-Projectiles)	-	400	-
4.18.2(c)(Projectile toys-Projectiles-Radius)	-	400	-
4.18.2(d) - 5.37(Projectile toys-Projectiles-length of suction cup projectiles)	-	600	-
4.18.2(d) - 5.37 - 5.24.5(Projectile toys-Projectiles-length of suction cup projectiles After torque test)	-	1200	-
4.18.2(d) - 5.37 - 5.24.6.5(Projectile toys-Projectiles-length of suction cup projectiles After tension test for a projectile with a suction cup)	-	1400	-
4.18.2 - e - 5.24.5(Projectile toys-Projectiles-torque test)	-	1100	-
4.18.2 - e - 5.24.6.5(Projectile toys-Projectiles-tension test for a projectile with a suction cup)	-	900	-
4.18.3(a) - 5.2(Projectile toys-Projectile toys with stored energy-small parts test)	-	800	-
4.18.3(a) - 5.3 - 5.24(Projectile toys-Projectile toys with stored energy-small parts test after reasonably foreseeable abuse testing)	-	2600	-
4.18.3(a) - 5.4(Projectile toys-Projectile toys with stored energy--small parts test after (wall impact test for projectiles)	-	800	-
4.18.3(b)(Projectile toys-Projectile toys with stored energy)	-	400	-
4.18.3(b) - 5.15.1.3.3(Projectile toys-Projectile toys with stored energy-determination of kinetic energy per area of contact)	-	1500	-
4.18.3(c ) - 5.24.5(Projectile toys-Projectile toys with stored energy-torque test)	-	900	-
4.18.3(c ) - 5.24.6.4(Projectile toys-Projectile toys with stored energy- tension test for protective components)	-	800	-
4.18.3(c )(Projectile toys-Projectile toys with stored energy)	-	400	-
4.18.3(d) - 5.15.2(Projectile toys-Projectile toys with stored energy-Wall impact test for projectiles)	-	1500	-
4.18.3(e )(Projectile toys-Projectile toys with stored energystored energy-Discharge mechanism)	-	400	-
4.18.4.1 - 5.20(Projectile toys-Projectile toys without stored energy-Mouth-actuated projectile toys-durability of mouth-actuated toys)	-	1500	-
4.18.4.2(a) - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-determination of the kinetic energy per area of contact when the contact area of the dart shall be at least 3 cm^2)	-	1500	-
4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart)	-	400	-
4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart)	-	400	-
4.18.4.2(b)(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart)	-	400	-
4.18.4.2(c ) - 5.24.5(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After torque test)	-	800	-
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-After tension test for protective components)	-	800	-
4.18.4.2(c ) - 5.24.6.4(Projectile toys-Projectile toys without stored energy-Projectiles in the form of a dart-Contact area After tension test for protective components)	-	800	-
4.18.4.3 - 5.15.1.3.3(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-kinetic energy per area)	-	1500	-
4.18.4.3 - 5.15.2(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)-wall impact test for projectiles)	-	1500	-
4.18.4.3(a)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	400	-
4.18.4.3(b)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	400	-
4.18.4.3(c)(Projectile toys-Projectile toys without stored energy-Arrows (e.g. bow and arrow set)	-	400	-
4.19(Rotors and propellers)	-	400	-
4.2(Aquatic toys)	-	400	-
4.2(Aquatic toys)	-	400	-
4.2(Aquatic toys)	-	400	-
4.2(Aquatic toys)	-	400	-
4.21(a)(Braking)	-	400	-
4.21(a)(Braking-brake performance for mechanically or electrically powered ride-on toys other than toy bicycles)	-	400	-
4.21(a)(braking)	-	400	-
4.21(b)(braking)	-	400	-
4.22.1(Toy bicycles-Instructions for use)	-	400	-
4.22.2(Toy bicycles-Determination of maximum saddle height)	-	400	-
4.22.3 - 5.16.1(Toy bicycles-Braking requirements-determination of free-wheeling facility)	-	900	-
4.22.3 (Toy bicycles-Braking requirements- brake lever dimension(d))	-	400	-
4.22.3 (Toy bicycles-Braking requirements- lever Length(l))	-	400	-
4.22.3 - 5.16.3(Toy bicycles-Braking requirements- brake performance for toy bicycles)	-	1500	-
4.23 - 5.17(Speed limitation of electrically driven ride-on toys-determination of speed of electrically driven ride-on toys)	-	1000	-
4.24(a) - 5.18(Toys containing a heat source-determination of temperature increases)	-	1300	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand-(Parts made of metals))	-	1300	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of glass or porcelain))	-	1300	-
4.24(b) - 5.18(Toys containing a heat source-rise in temperature of handles, knobs and similar parts which are likely to be touched by hand(Parts made of Plastic or wood ))	-	1300	-
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy(Parts made of metals))	-	1300	-
4.24(c) - 5.18(Toys containing a heat source- rise in temperature of other accessible parts of the toy( Parts made of other materials))	-	1300	-
4.25 - 5.19(Liquid-filled toys-leakage of liquid-filled toys)	-	1200	-
4.25(Liquid-filled toys)	-	400	-
4.26(a) - 5.2( Mouth-actuated toys-small parts test)	-	800	-
4.26(b) - 5.24.5 - 5.3( Mouth-actuated toys-small parts test after torque test)	-	1200	-
4.26(b) - 5.24.6.1 - 5.4( Mouth-actuated toys-small parts test after tension test, general procedure)	-	1300	-
4.26(c ) - 5.20 - 5.2( Mouth-actuated toys-small parts test after durability of mouth-actuated toys)	-	1500	-
4.27(Toy roller skates, toy inline skates and toy skateboards)	-	400	-
4.28( Percussion caps specifically designed for use in toys)	-	400	-
4.28( Percussion caps specifically designed for use in toys)	-	400	-
4.29(a) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	3000	-
4.29(b) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	3000	-
4.29(c) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	3000	-
4.29(d) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	3000	-
4.29(e) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	3000	-
4.29(f) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	3000	-
4.29(g) - 5.25(Acoustic requirements-determination of sound pressure levels)	-	3000	-
4.30.2(Toy scooters-Warnings and instructions for use)	-	400	-
4.30.3 - 5.26 - 5.8(Toy scooters-Strength-After static strength for toy scooters- sharp edge test)	-	1900	-
4.30.3 - 5.26 - 5.9(Toy scooters-Strength-static strength for toy scooters-sharp-point test)	-	1900	-
4.30.3 - 5.26(Toy scooters-Strength-static strength for toy scooters)	-	1500	-
4.30.3 - 5.27 - 5.8(Toy scooters-Strength-dynamic strength for toy scooters- sharp-edge test)	-	4600	-
4.30.3 - 5.27 - 5.9(Toy scooters-Strength-dynamic strength for toy scooters-sharp-point test)	-	4700	-
4.30.3 - 5.27(Toy scooters-Strength-dynamic strength for toy scooters)	-	4200	-
4.30.3 - 5.29(Toy scooters-Strength-strength of toy scooter steering tubes)	-	2500	-
4.30.4 - 5.12.2(Toy scooters-Stability-sideways stability test, feet available for stabilization)	-	900	-
4.30.5(a)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	400	-
4.30.5(b)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	400	-
4.30.5(c)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	400	-
4.30.5(d)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	400	-
4.30.5(e)( Toy scooters-Adjustable and folding steering tubes and handlebars)	-	400	-
4.30.5(f) - 5.30( Toy scooters-Adjustable and folding steering tubes and handlebars-resistance to separation of handlebar)	-	1300	-
4.30.6 ( Toy scooters-Braking)	-	400	-
4.30.6 ( Toy scooters-Braking)	-	400	-
4.30.6 - 5.28( Toy scooters-Braking- force required to hold the toy)	-	1500	-
4.30.7( Toy scooters-Wheel size(diameter))	-	400	-
4.30.8(Toy scooters-Projections)	-	400	-
4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs Diameter))	-	400	-
4.30.8(Toy scooters-Projections(rounded handlebar grips or plugs space from end))	-	400	-
4.31(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over)	-	400	-
4.31.1 - 5.32(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-magnetic flux index)	-	1900	-
4.31.1 - 5.2(Magnets and magnetic components-Magnetic/electrical experimental sets intended for children 8 years and over-small parts test)	-	800	-
4.31.2(a) - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index)	-	1900	-
4.31.2(b) - 5.34 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-soaking test for magnets-small parts test)	-	1400	-
4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.32(Magnets and magnetic components-All other toys with magnets and magnetic components-magnetic flux index After Following tests: -tension test for magnets; -drop test/tip over test for large and bulky toys; -torque test; -tension test, general procedure; -tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable; -impact test for magnets; -compression test; -tension test for magnets;)	-	3600	-
4.31.2(c ) - 5.31 - 5.24.2 - 5.24.3 - 5.24.5 - 5.24.6.1 - 5.24.6.2 - 5.33 - 5.31 - 5.2(Magnets and magnetic components-All other toys with magnets and magnetic components-small parts test After Following tests: -tension test for magnets; -drop test/tip over test for large and bulky toys; -torque test; -tension test, general procedure; -tension test for seams in soft-filled (stuffed) toys, beanbag-type toys and other similar filled toys, if applicable; -impact test for magnets; -compression test; -tension test for magnets;)	-	3500	-
4.32 - 5.38.2( Yo-yo balls - length (lo) of the yo-yo ball tether)	-	1200	-
4.32 - 5.38.1( Yo-yo balls - The ratio of the mass m (in grams) to the elastic constant k of the yo-yo ball tether(m/k))	-	1200	-
4.33 - 5.11.3(Straps intended to be worn fully or partially around the neck-breakaway feature separation test)	-	800	-
4.34(Sledges and toboggans with cords for pulling)	-	400	-
4.35.3 - 5.39(Jaw entrapment in handles and steering wheels-jaw entrapment test)	-	1200	-
9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-Test for soft-filled toys )	-	1500	-
9873 (Part - 2) 4.5 - 5.5(Soft-filled toys-rate of spread of flame )	-	1500	-
9873 (Part - 2) 4.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	500	-
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child )	-	1500	-
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	1500	-
9873 (Part - 2) 4.4 - 5.4(Toys intended to be entered by a child-rate of spread of flame)	-	1500	-
9873 (Part - 2) 4.3(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play)	-	500	-
9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-Test relating to flowing elements of toys to be worn on the head (except those covered by 4.2.2 and 4.2.3), hoods, headdresses, etc. and masks not covered by 4.2.4 which partially or fully cover the head (e.g. fabric and cardboard masks, eye masks, face masks), toy disguise costumes and toys intended to be entered or worn by a child)	-	1500	-
9873 (Part - 2) 4.3 - 5.4(Toys to be worn on the head-Toy disguise costumes and toys intended to be worn by a child in play-rate of spread of flame)	-	1500	-
9873 (Part - 9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	4000	per material, Additional charges for different material applicable
9873 (Part - 9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	1500	per material, Additional charges for different material applicable
9873 (Part - 9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	1500	per material, Additional charges for different material applicable
9873 (Part - 9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	1500	per material, Additional charges for different material applicable
4.1(Normal use)	-	3400	-
4.3.1(Material quality)	-	400	-
5.24.6.1(Tension Test General procedure)	-	500	-
4.16.1(Enclosures-Ventilation)	-	600	-
4.16.1(Enclosures-Ventilation)	-	400	-
9873 (Part - 3) 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 )	-	500	-
9873 (Part - 3) 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 )	-	500	-
9873 (Part - 3) 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 )	-	500	-
9873 (Part - 3) 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 )	-	500	-
9873 (Part - 3) 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9)	-	500	-
9873 (Part - 3) 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 )	-	500	-
9873 (Part - 3) 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 )	-	500	-
9873 (Part - 3) 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9)	-	500	-

-
-

IS 15644 (2006)

Safety of electric toys

All

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.0(Marking and instructions)	-	1000	-
8.0(Power Input)	-	1200	-
9.0(Heating and abnormal operation)	-	1100	-
10.0(Electrical strength at operating temperature)	-	1200	-
11.1(Moisture resistance)	-	1200	-
11.2(Resistant to humidity)	-	1200	-
12.0(Electric strength at room temperature)	-	1400	-
13.0(Mechanical strength)	-	1100	-
14.1(Construction)	-	400	-
14.2(Construction)	-	300	-
14.3(Construction)	-	300	-
14.4(Construction)	-	300	-
14.5(Construction)	-	400	-
14.6(Construction)	-	400	-
14.7(Construction)	-	1000	-
14.8(Construction)	-	300	-
14.9(Construction)	-	500	-
14.1(Construction)	-	500	-
14.11(Construction)	-	600	-
14.12(Construction)	-	500	-
14.13(Construction)	-	600	-
14.14(Construction)	-	300	-
15.1(Protection of cords and wires)	-	500	-
15.2(Protection of cords and wires)	-	1100	-
16.0(Components)	-	1900	-
17 Table-1(Screws and connections)	-	1100	-
17 Table-1(Nominal daimeter of screws made of insulating material)	-	1500	-
18.0(Clearance and creepage distance)	-	1100	-
19.1(Ball pressure test IEC 60695-10-2)	-	1500	-
19.2.1(Glow wire test IEC 60695-2-11)	-	1700	-
19.2.2(Needle flame test)	-	2000	-
9873 (Part-9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	4000	per material, Additional charges for different material applicable
9873 (Part-9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	4000	per material, Additional charges for different material applicable
9873 (Part-9) 3(Vinyl in any part of the toy or childcare article that can be placed in mouth of a child under 4 years of age - a) Di-iso-Nonyl Phthalate (DINP), b) Di-iso-Decyl Phthalate (DIDP), c) Di-n-Octyl Phthalate (DNOP) - IS 9873 Part 6)	-	4000	per material, Additional charges for different material applicable
9873 (Part-9) 3(Vinyl in toys or childcare articles - a) Bis-(2-ethlyhexyl) Phthalates (DEHP), b) Di-Butyl phthalate (DBP), c) Benzyl butyl Phthalate (BBP) - IS 9873 Part 6)	-	4000	per material, Additional charges for different material applicable
9873 (Part-3) 4.1 - Table 1(Selenium (Se) - Cl 7,8,9 )	-	500	-
9873 (Part-3) 4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 )	-	500	-
9873 (Part-3) 4.1 - Table 1(Lead (Pb) - Cl 7,8,9 )	-	500	-
9873 (Part-3) 4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 )	-	500	-
9873 (Part-3) 4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9)	-	500	-
9873 (Part-3) 4.1 - Table 1(Barium (Ba) - Cl 7,8,9 )	-	500	-
9873 (Part-3) 4.1 - Table 1(Arsenic (As) - Cl 7,8,9 )	-	500	-
9873 (Part-3) 4.1 - Table 1(Antimony (Sb) - Cl 7,8,9)	-	500	-

-
-

IS 9873 : Part 3 (2017)

Safety of toys: Part 3 migration of certain elements (Second Revision)

Migration of Certain Elements

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	500	-
4.1 - Table 1(Antimony (Sb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated
4.1 - Table 1(Arsenic (As) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated
4.1 - Table 1(Barium (Ba) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated
4.1 - Table 1(Cadmium (Cd) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated
4.1 - Table 1(Chromium (Cr) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated
4.1 - Table 1(Lead (Pb) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated
4.1 - Table 1(Mercury (Hg) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated
4.1 - Table 1(Selenium (Se) - Cl 7,8,9 of IS 9873-3 : 2017 and ISO 8124-3 : 2010)	-	0	Test Repeated

-
Included w.e.f. 26.11.2024

IS 14544 (2022)

LEATHER SAFETY AND PROTECTIVE FOOTWEAR WITH DIRECT MOULDED POLYVINYL CHLORIDE PVC SOLE - SPECIFICATION First Revision

Leather Safety and Protective Footwear with Direct Moul

72600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Effective Date	Remark
8.1(Cl. No. 5.10 of IC 15298(P-1):2015)	-	68600		Clause No. 6 (Physical Requirements) & Clause No. 7 (Chemical Requirements)
8.2(Cl. No. 5.10 of IC 15298(P-1):2015)	-	4000		Clause No. 8 (Additional Requirements)

-
Included w.e.f 10.12.2024

IS 1989 : Part 2 (1986)

Specification for leather safety boots and shoes: Part 2 for heavy metal industries (Fourth Revision)

Leather Safety Boots and Shoes: Part 2 Heavy Metal Ind.

72200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Marking)	-	0	-
7(Design)	-	200	-
8(a) Upper Leather)	-	2300	Clause 8.1
8(b) Lining Leather)	-	5300	Clause 8.2
8(c) Bottom Material)	-	15200	Clause 8.3
8(d) Steel Toe Cap)	-	3200	Clause 8.4
8(e) Tape)	-	700	Clause 8.5
8(f) Bottom Filling)	-	300	Clause 8.6
8(g) Eyelet)	-	200	Clause 8.7
8(h) Toe Compound)	-	300	Clause 8.8
8(i) Threads)	-	1700	Clause 8.9
8(j) Rivets)	-	300	Clause 8.10
8(k) Screw Wire)	-	0	Clause 8.11
8(l) Heel Pin)	-	200	Clause 8.12
8(m) Shank)	-	200	Clause 8.13
8(n) Laces)	-	1700	Clause 8.14
8(o) Tongue Lining)	-	300	Clause 8.15
8(p) Adhesive)	-	200	Clause 8.16
8(q) Strengthening Piece)	-	200	Clause 8.17
8(r) Leather Components)	-	400	Clause 8.18
9(Manufacture)	-	0	Clause 9
10(Finish)	-	200	Clause 10
11(a) Boots with Leather Sole and Heel)	-	300	Clause 11.1
11(b) Boots with Rubber Sole and Heel)	-	300	Clause 11.2
12(Performance Test)	-	2000	Clause 11.2 Package Testing Charges for Section 1 : RS. 35400
13(Design)	-	200	Clause 13
14(a) Upper Leather)	-	2300	Clause 14.1
14(b) Lining Leather)	-	5300	Clause 14.2
14(c) Bottom Material)	-	16200	Clause 14.3
14(d) Steel Toe Cap)	-	3500	Clause 14.4
14(e) Tape)	-	1000	Clause 14.5
14(f) Bottom Filling)	-	300	Clause 14.6
14(g) Eyelet)	-	200	Clause 14.7
14(h) Toe Compound)	-	300	Clause 14.8
14(i) Threads)	-	1700	Clause 14.9
14(j) Rivets)	-	300	Clause 14.10
14(k) Screw Wire)	-	0	Clause 14.11
14(l) Heel Pin)	-	200	Clause 14.12
14(m) Shank)	-	200	Clause 14.13
14(n) Laces)	-	1700	Clause 14.14
14(o) Tongue Lining)	-	300	Clause 14.15
14(p) Adhesive)	-	200	Clause 14.16
14(q) Leather Components)	-	400	Clause 14.17
15(Manufacture)	-	0	Clause 15
16(Finish)	-	200	Clause 16
17(a) Shoes with Leather Sole and Heel)	-	300	Clause 17.1
17(b) Shoes with Rubber Sole and Heel)	-	300	Clause 17.2
18(Performance Test)	-	2000	Clause 18 Package Testing Charges for Section 1 : RS. 36800
4(Marking)	-	0	Clause Repeated
7(Design)	-	0	Clause Repeated
8(a) Upper Leather)	-	0	Clause Repeated
8(b) Lining Leather)	-	0	Clause Repeated
8(c) Bottom Material)	-	0	Clause Repeated
8(d) Steel Toe Cap)	-	0	Clause Repeated
8(e) Tape)	-	0	Clause Repeated
8(f) Bottom Filling)	-	0	Clause Repeated
8(g) Eyelet)	-	0	Clause Repeated
8(h) Toe Compound)	-	0	Clause Repeated
8(i) Threads)	-	0	Clause Repeated
8(j) Rivets)	-	0	Clause Repeated
8(k) Screw Wire)	-	0	Clause Repeated
8(l) Heel Pin)	-	0	Clause Repeated
8(m) Shank)	-	0	Clause Repeated
8(n) Laces)	-	0	Clause Repeated
8(o) Tongue Lining)	-	0	Clause Repeated
8(p) Adhesive)	-	0	Clause Repeated
8(q) Strengthening Piece)	-	0	Clause Repeated
8(r) Leather Components)	-	0	Clause Repeated
9(Manufacture)	-	0	Clause Repeated
10(Finish)	-	0	Clause Repeated
11(a) Boots with Leather Sole and Heel)	-	0	Clause Repeated
11(b) Boots with Rubber Sole and Heel)	-	0	Clause Repeated
12(Performance Test)	-	0	Clause Repeated
13(Design)	-	0	Clause Repeated
14(a) Upper Leather)	-	0	Clause Repeated
14(b) Lining Leather)	-	0	Clause Repeated
14(c) Bottom Material)	-	0	Clause Repeated
14(d) Steel Toe Cap)	-	0	Clause Repeated
14(e) Tape)	-	0	Clause Repeated
14(f) Bottom Filling)	-	0	Clause Repeated
14(g) Eyelet)	-	0	Clause Repeated
14(h) Toe Compound)	-	0	Clause Repeated
14(i) Threads)	-	0	Clause Repeated
14(j) Rivets)	-	0	Clause Repeated
14(k) Screw Wire)	-	0	Clause Repeated
14(l) Heel Pin)	-	0	Clause Repeated
14(m) Shank)	-	0	Clause Repeated
14(n) Laces)	-	0	Clause Repeated
14(o) Tongue Lining)	-	0	Clause Repeated
14(p) Adhesive)	-	0	Clause Repeated
14(q) Leather Components)	-	0	Clause Repeated
15(Manufacture)	-	0	Clause Repeated
16(Finish)	-	0	Clause Repeated
17(a) Shoes with Leather Sole and Heel)	-	0	Clause Repeated
17(b) Shoes with Rubber Sole and Heel)	-	0	Clause Repeated
18(Performance Test)	-	0	Clause Repeated
4(Marking)	-	0	Clause Repeated
7(Design)	-	0	Clause Repeated
8(a) Upper Leather)	-	0	Clause Repeated
8(b) Lining Leather)	-	0	Clause Repeated
8(c) Bottom Material)	-	0	Clause Repeated
8(d) Steel Toe Cap)	-	0	Clause Repeated
8(e) Tape)	-	0	Clause Repeated
8(f) Bottom Filling)	-	0	Clause Repeated
8(g) Eyelet)	-	0	Clause Repeated
8(h) Toe Compound)	-	0	Clause Repeated
8(i) Threads)	-	0	Clause Repeated
8(j) Rivets)	-	0	Clause Repeated
8(k) Screw Wire)	-	0	Clause Repeated
8(l) Heel Pin)	-	0	Clause Repeated
8(m) Shank)	-	0	Clause Repeated
8(n) Laces)	-	0	Clause Repeated
8(o) Tongue Lining)	-	0	Clause Repeated
8(p) Adhesive)	-	0	Clause Repeated
8(q) Strengthening Piece)	-	0	Clause Repeated
8(r) Leather Components)	-	0	Clause Repeated
9(Manufacture)	-	0	Clause Repeated
10(Finish)	-	0	Clause Repeated
11(a) Boots with Leather Sole and Heel)	-	0	Clause Repeated
11(b) Boots with Rubber Sole and Heel)	-	0	Clause Repeated
12(Performance Test)	-	0	Clause Repeated
13(Design)	-	0	Clause Repeated
14(a) Upper Leather)	-	0	Clause Repeated
14(b) Lining Leather)	-	0	Clause Repeated
14(c) Bottom Material)	-	0	Clause Repeated
14(d) Steel Toe Cap)	-	0	Clause Repeated
14(e) Tape)	-	0	Clause Repeated
14(f) Bottom Filling)	-	0	Clause Repeated
14(g) Eyelet)	-	0	Clause Repeated
14(h) Toe Compound)	-	0	Clause Repeated
14(i) Threads)	-	0	Clause Repeated
14(j) Rivets)	-	0	Clause Repeated
14(k) Screw Wire)	-	0	Clause Repeated
14(l) Heel Pin)	-	0	Clause Repeated
14(m) Shank)	-	0	Clause Repeated
14(n) Laces)	-	0	Clause Repeated
14(o) Tongue Lining)	-	0	Clause Repeated
14(p) Adhesive)	-	0	Clause Repeated
14(q) Leather Components)	-	0	Clause Repeated
15(Manufacture)	-	0	Clause Repeated
16(Finish)	-	0	Clause Repeated
17(a) Shoes with Leather Sole and Heel)	-	0	Clause Repeated
17(b) Shoes with Rubber Sole and Heel)	-	0	Clause Repeated
18(Performance Test)	-	0	Clause Repeated

-
Included w.e.f 10.12.2024

IS 1989 : Part 1 (1986)

Specification for leather safety boots and shoes: Part 1 for miners (Fourth Revision)

Specification for leather safety boots and shoes: Part

84300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 (a)(Marking)	-	0	-
4.1 (b)(Marking)	-	0	-
4.1 (c)(Marking)	-	0	-
4.1 (d)(Marking)	-	0	-
4.1 (e)(Marking)	-	0	-
7.1(Design)	-	38300	Section 1 (Clause 7.1, Clause 8)
10.1(Finish)	-	0	-
10.3(Finish)	-	200	-
10.4(Finish)	-	200	-
11.1(Mass Boots with Leather Sole and Heel)	-	300	-
11.2(Mass Boots with Rubber Sole and Heel)	-	300	-
12(Performance test)	-	2000	-
13(Design)	-	40400	Section 2 (Clause 13 & Clause 14)
16.1(Finish)	-	200	-
16.2(Finish)	-	0	-
16.3(Finish)	-	200	-
16.4(Finish)	-	200	-
17.1(Mass Shoes with Leather Sole and Heel)	-	300	-
17.2(Mass Shoes with Rubber Sole and Heel)	-	300	-
18(Performance test)	-	2000	-

-
Included w.e.f 10.12.2024

IS 11226 (1993)

Leather safety footwear having direct moulded rubber sole specification (First Revision)

Leather safety footwear having direct moulded rubber so

24750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(REQUIREMENTS)	-	0	-
5.2(Materials)	-	0	-
5.2.1(Materials)	-	7000	Thickness, Tensile strength, El. at Break, Stitch tear strength, Distension and strength of grain, Flexural endurance,, Tongue tear, C.F to Rubbing, Solvent extractable substances, Chromic Oxide, Water soluble matter, pH of water solubles, Heat Shrinkage
5.2.1.1(Materials)	-	0	-
5.2.2(Materials)	-	10800	Thickness, Density, Water absorption, Tensile str. - Dry & Wet Condition, El. at break, Area shrinkage, Linear shrinkage, Stitch tear str, Flexing endurance, Mineral ash, Water soluble matter, Lthr forming material, Surface Water Absorption, Crack resis.
5.2.3(Materials)	-	9000	Materials (Stiffener) - First dry collapsing load Hardness, Resilience, Moisture resistance, Initial dry area shape retention, Area shape retention after 10th collapse), Peel Strength
5.2.4(Materials)	-	18100	Tests as per IS 3840 LP 1, 6, 9, 8, LC-4, 10, 8, 18, 21, 5, Apdx A, IS 14816 LC3, LC - 4, LC 2, IS 14575,
5.2.5(Materials)	-	1800	Thread - Length (M/kg), Breaking Strength,
5.2.6.1(Materials)	-	500	-
5.2.6.2(Materials)	-	0	-
5.2.6.3(Materials)	-	300	-
5.2.7(Materials)	-	300	-
5.2.8(Materials)	-	300	-
5.2.9(Materials)	-	300	-
5.2.10(Materials)	-	3900	Lace - Length, Breaking Strength, C. F. to Washing, C. F. to Light, Slip Resistance, Detection of Sulphur Dye
5.2.11(Materials)	-	500	-
5.2.11.1(Materials)	-	300	-
5.2.11.2(Materials)	-	3500	Tensile Strength, Elongation at Break, Relative Density, Change in Volume, Flexing Resistance
5.2.11.3(Materials)	-	1500	-
5.3(Components)	-	600	-
5.4( Manufacture )	-	0	-
5.4.1( Manufacture )	-	0	-
5.4.8(Workmanship and Finish)	-	500	-
5.5(Mass)	-	300	-
5.6(Performance Test)	-	2000	-
5.7(Adhesion Test on Moulded Bottoms)	-	1000	-
7(MARKING)	-	0	-
5.7(Toe adhesion )	-	0	Clause Repeated
5.6.(Toe Impact test)	-	0	Clause Repeated
5.5(Mass per pairs)	-	0	Clause Repeated
5.4.8(Leg height)	-	0	Clause Repeated
5.4(Dimension )	-	0	Clause Repeated
5.3 & 5.4.2(Thickness of components )	-	0	Clause Repeated
5.2.11.2(Flexing resistance)	-	0	Clause Repeated
5.2.11.2(Resistance to Fuel Oil)	-	0	Clause Repeated
5.2.11.2(Elongation at break)	-	0	Clause Repeated
5.2.11.2(Tensile Strength)	-	0	Clause Repeated
5.2.11.2(Hardness (Shore A))	-	0	Clause Repeated
5.2.11(Hardness (IRHD)-after ageing)	-	0	Clause Repeated
5.2.11(Flexing resistance)	-	0	Clause Repeated
5.2.11(Elongation at break)	-	0	Clause Repeated
5.2.11(Tensile Strength)	-	0	Clause Repeated
5.2.11(Hardness (IRHD))	-	0	Clause Repeated
5.2.11(Relative density )	-	0	Clause Repeated
5.2.6(Materials)	-	0	Clause Repeated

-
Included w.e.f 26.11.24

IS 3976 (2018)

Safety Rubber Canvas Boots for Miners Ã¢â‚¬ Specification ( Sixth Revision )

Safety Boots for miners

62100 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1(Design)	-	300	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	400	-
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	400	-
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	1000	-
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	1000	-
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	1000	-
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	500	-
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	1000	-
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	300	-
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	500	-
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	1000	-
5.2.4(Reinforcing Material)	-	300	-
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	0	-
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	500	-
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	1500	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	1000	Thickness of Component
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	1000	Abrasion Resistance
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	1000	Flexing Resistance
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	500	Tear Strength
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	Resistance to Hot contact
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	1500	Hydrolysis
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	1500	Ageing of Whole Footwear
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	400	-
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	1000	Detection of Sulphur Dye
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	500	Safety Toe Cap - Dimensions
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	1500	Safety Toe Cap - Performance Test
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	1000	Safety Toe Cap - Finish (Rs. 500) Safety Toe Cap - Rust prevention (Rs. 500)
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	300	5.2.9.1
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	500	5.2.9.2
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	1000	5.2.9.3
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	500	5.2.10
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	300	5.2.11
5.3, 5.3.1,5.3.3,5.3.4(Construction)	-	300	5.3.1 Construction - Stitch/dm
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	0	-
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	0	-
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	600	-
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	300	-
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	300	-
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	300	-
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	300	-
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	2000	-
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	1000	-
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	1000	-
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	1000	-
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	1000	-
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	1500	-
7.1(Resistance to fuel)	-	1000	-
8(CHEMICAL REQUIREMENTS)	-	26500	-
9, 9.1(BIS CERTIFICATION MARKING)	-	0	-
9, 9.1(BIS CERTIFICATION MARKING)	-	0	-
10(Marking)	-	0	-
10(Marking)	-	0	-
Cl. 8 (IS 17011, Table-1 (i))(Allergenic and carcinogenic disperse dyes)	-	0	Clause Repeated
11(Packing)	-	0	Clause Repeated
11(PACKING)	-	0	Clause Repeated
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	0	Clause Amended
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	0	Clause Repeated
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	0	Clause Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Amended
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	0	Clause Amended
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	300	-
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	0	-
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	0	Clause Amended
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	0	Clause Amended
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	0	Clause Amended
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	0	Clause Amended
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	0	Clause Amended
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	0	Clause Amended
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Claus Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	0	Claus Repeated
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	0	Clause Amended
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	0	Clause Amended
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Amended
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	0	Clause Amended
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	0	Clause Amended
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	0	Clause Amended
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	0	Clause Amended
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	0	Clause Amended
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	0	Clause Repeated
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	0	Clause Repeated
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	0	Clause Repeated
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	0	Clause Repeated
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	0	Clause Repeated
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	0	Clause Repeated
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	0	Clause Repeated
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	0	Clause Repeated
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	0	Clause Repeated
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	0	Clause Repeated
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	0	Clause Repeated
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	0	Clause Repeated
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	0	Clause Amended
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	0	Clause Amended
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	0	Clause Amended
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	0	Clause Amended
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	0	Clause Amended
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	0	Clause Amended
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Amended
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	0	Clause Amended
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	0	Clause Repeated
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	0	Clause Amended
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	0	Clause Amended
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	0	Clause Amended
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	0	Clause Amended
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Amended
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	0	Clause Amended
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	0	Clause Amended
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	0	Clause Amended
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	0	Clause Amended
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	0	Clause Amended
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	0	Clause Amended
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	0	Clause Amended
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	0	Clause Amended
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	0	Clause Repeated
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	0	Clause Repeated
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	0	Clause Repeated
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	0	Clause Repeated
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	0	Clause Repeated
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	0	Clause Repeated
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	0	Clause Repeated
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	0	Clause Repeated
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	0	Clause Repeated
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	0	Clause Repeated
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	0	Clause Repeated
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	0	Clause Amended
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	0	Clause Amended
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	0	Clause Amended
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	0	Clause Amended
4(Types)	-	0	-
5(Requirements)	-	0	-
5.10(consolidation test IS 3400 (Part 5))	-	0	Clause Repeated
5.2.8.4(Colour of the lace)	-	0	Clause Amended
5.10(Consolidation Test IS 3400 (Part 5) : 1986)	-	0	Clause Amended
Cl. 5.2.4(Reinforcing Material)	-	0	Clause Amended
Cl. 5.2.8.4(Colour of the lace)	-	0	Clause Amended
Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4)	-	0	Clause Repeated
7.2(Resistance to electricity)	-	0	Clause Repeated
5.1(Design)	-	0	Clause Repeated
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	0	Clause Repeated
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	0	Clause Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	0	Clause Repeated
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
5.2.4(Reinforcing Material)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	0	Clause Repeated
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	0	Clause Repeated
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	0	Clause Repeated
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	0	Clause Repeated
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
Cl.5.2.5.4 Thickness of compact sole hee(of black cotton thread, the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	0	Clause Repeated
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	0	Clause Repeated
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	0	Clause Repeated
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	0	Clause Repeated
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	0	Clause Repeated
Cl.5.2.7 Safety Toe Cap(Safety toe cap as per 3.6 shall be fitted into the footwear and must not come out while in use.)	-	0	Clause Repeated
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	0	Clause Repeated
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	0	Clause Repeated
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	0	Clause Repeated
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	0	Clause Repeated
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	0	Clause Repeated
5.3, 5.3.1,5.3.3,5.3.4(Construction)	-	9	Clause Repeated
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	0	Clause Repeated
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	-0	Clause Repeated
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	0	Clause Repeated
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	0	Clause Repeated
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	0	Clause Repeated
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	0	Clause Repeated
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	0	Clause Repeated
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	0	Clause Repeated
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	0	Clause Repeated
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	0	Clause Repeated
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	0	Clause Repeated
7.1(Resistance to fuel)	-	0	Clause Repeated
8(CHEMICAL REQUIREMENTS)	-	0	Clause Repeated
9, 9.1(BIS CERTIFICATION MARKING)	-	0	Clause Repeated
9, 9.1(BIS CERTIFICATION MARKING)	-	0	Clause Repeated
10(Marking)	-	0	Clause Repeated
10(Marking)	-	0	Clause Repeated
Cl. 8 (IS 17011, Table-1 (i))(Allergenic and carcinogenic disperse dyes)	-	0	Clause Repeated
11(Packing)	-	0	Clause Repeated
11(PACKING)	-	0	Clause Repeated
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	0	Clause Repeated
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	0	Clause Repeated
Cl.5.13 Energy Absorption Test(When footwear is tested in accordance with the method prescribed in 5.14 of IS 15298 (Part 1), the energy absorption of the seat region shall not be less than 20 J.)	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material Annex C(ii) Breaking load in N, Min (50 cm grip length test specimen) )	-	0	Clause Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Repeated
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	0	Clause Repeated
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	0	Clause Repeated
Cl.5.2.5.3 Ageing for whole footwear(When rubber is used for manufacturing boots or when the outer sole heel is made of bi-polymer, the finished boots shall be aged at 100 ± 2°C for 24 h. On completion of test, all rubber components shall not develop any sign of tackiness or brittleness.)	-	0	Clause Repeated
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	2000	Slip Resistance
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	0	Clause Repeated
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	0	Clause Repeated
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	0	Clause Repeated
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	0	Clause Repeated
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	0	Clause Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	0	Clause Repeated
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	0	Clause Repeated
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	0	Clause Repeated
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	0	Clause Repeated
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	0	Clause Repeated
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	0	Clause Repeated
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	0	Clause Repeated
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	0	Clause Repeated
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	0	Clause Repeated
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	0	Clause Repeated
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	0	Clause Repeated
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	0	Clause Repeated
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	0	Clause Repeated
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	0	Clause Repeated
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	0	Clause Repeated
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	0	Clause Repeated
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	0	Clause Repeated
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	0	Clause Repeated
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	0	Clause Repeated
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	0	Clause Repeated
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	0	Clause Repeated
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	0	Clause Repeated
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel Cl.5.2.5.1 IS 3400 (Part 2)(requirements prescribed in col 3 of Table 2 when tested as per corresponding test methods prescribed in col 4 of Table 2. i)i) Hardness (IRHD)	-	0	Clause Repeated
Cl.6.3 Tear Strength of Compact Outsole( When outsoles are tested in accordance to 8.2 of IS 15298 (Part 1), the tear strength shall be not less than 8 kN/m for material having density higher than 0.9/cm³ and when density of material is less than or equal to 0.9 g/cm³, tear strength shall not be less than 5 kN/m.)	-	0	Clause Repeated
Cl.5.2.3 Coated Binding Material IS 1954( Coated binding materials shall conform to the requirements given in col 3 of Table 1 when tested according to the methods prescribed in col 4 of Table 1. i)Width in mm, )	-	0	Clause Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water coefficient as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.1.4 ( Type 2 footwear, the composite upper material shall comply with requirements of water vapour permeability as prescribed in 5.4.6 of IS 15298 (Part 2).)	-	0	Clause Repeated
CL.5.2.10 Counter Stiffener( A counter stiffener, made out of textile reinforced withpolymer/rubber including (thermoplastic) having thickness not less than 1.5 mm is to be stitched at inside of upper so as to fortify the back of the footwear at joints of quarter.)	-	0	Clause Repeated
Cl.5.1.1 Fittings(Fittings of the footwear shall be in conformity to Table 9 of IS 1638 (measurement of men’s lasts) and Table 8 of IS 1638 (measurement of women’s lasts).)	-	0	Clause Repeated
Cl.5.2.1 Upper Cl.5.2.1.1 IS 3400(Part 5)( Composite upper material shall comply with consolidation test as per 5.10.(IS 3400 (Part 5). There shall be no separation at a load of 1.5 kg.))	-	0	Clause Repeated
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	0	Clause Repeated
Cl.5.2.1.5( Inner layer of upper shall meet requirement of abrasion resistance as prescribed in 5.5.2 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.2 Compact Insole/Compact Insocks/Counter Stiffener Lining(Textile material shall be used as lining material for compact insole/compact insocks / counter stiffener. It shall meet the requirement of tear strength as prescribed in 5.6.1 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.2.1 Abrasion resistance of compact insole/insocks/ counter stiffener( When textiles used as lining for all the above are tested in accordance with 6.12 of IS 15298 (Part 1), the lining shall not develop any holes before the following number of cycles has been performed:)	-	0	Clause Repeated
Cl.5.2.3.1 In case of cotton black binding materia( the same shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel Cl. 5.2.5.1 (The compact sole heel shall be made out of polymeric/rubber components and the typical design recommendation (not mandatory) of compact sole heel is as shown in Fig. 3. Sectional view of Type 1/Type 2 ) toe position is given in Fig. 4.)	-	0	Clause Repeated
Cl.5.2.5 Compact Sole Heel 5.2.5.1 IS 3400 (Part 4)(ii)*Change in hardness after accelerated ageing at 100 ± 2 °C for 24 h )	-	0	Clause Repeated
Cl.5.2.5.4 Thickness of compact sole hee(Thickness of compact sole heel of the boots shall comply with the thickness and material requirements prescribed in Table 3.)	-	0	Clause Repeated
Cl.5.2.6 Thread for Upper Closing( The length (m/kg) and construction of sewing thread shall conform to requirements as prescribed in Table 4.)	-	0	Clause Repeated
Cl.5.2.8.1( The boots shall be provided with laces having minimum length of 115 cm for Type 1 and minimum 100 cm for Type 2.)	-	0	Clause Repeated
Cl.5.2.8.2 (Minimum breaking load of 60 kg is to be achieved when tested between 18 cm grip length in accordance with Annex C.)	-	0	Clause Repeated
Cl.5.2.8.3( In case of cotton lace of black colour, the same shall be free from sulphur dyes when tested in accordance with Annex B. Two ends of the laces shall be provided with plastic tips.)	-	0	Clause Repeated
Cl.5.2.9 Eyelets( Aluminum eyelets of external collar diameter not less than 10 mm and wall thickness of 0.30 to 0.35 mm shall be used.)	-	0	Clause Repeated
Cl.5.3.2 (The tongue shall be made out of composite upper material and shall be half bellow type for Type 2 and full bellow type for Type 1.)	-	0	Clause Repeated
Cl.5.3.5 Outer toe cap( shall be provided which is made of polymer/rubber and it shall be strongly adhered such that it shall not open up or come out while in use. Toe of the boot shall be reinforced with safety toe cap)	-	0	Clause Repeated
Cl.5.3.6( A designed foxing of width of minimum 25 mm and of thickness of minimum 2 mm is to be provided. The foxing shall not extend the edges of the outer sole.)	-	0	Clause Repeated
Cl.5.3.7( Two pairs of detachable insocks are to be provided. The insocks shall be compact in nature having thickness not less than 2 mm.)	-	0	Clause Repeated
Cl.5.4 Finish( In appearance, general workmanship and in all other respects with regard to finish and get up of the footwear, the footwear shall be matching to the approved sample of the purchaser.)	-	0	Clause Repeated
Cl.5.5 Mass(The mass of one pair of finished footwear of size 8 shall not exceed 1 500 g for Type 1 and 1 400 g for Type 2 with an increase or decrease of 100 g for each bigger or smaller size, respectively.)	-	0	Clause Repeated
Cl.5.6( Height of Upper Height of upper of the boots shall conform to column 5 (Design C) and column 4 (Design B) of 5.2.2, Table 4 of IS 15298 (Part 2) for Type 1 and Type 2, respectively when measured as per 6.2 of IS 15298 (Part 1) on the inside of the back of the footwear and from seat of the insole to top edge of the upper.)	-	0	Clause Repeated
Cl.5.7 Performance Test(When safety footwear is tested in accordance with the method described in 5.4 of IS 15298 (Part 1), at an impact energy of (200 ± 4) J, the clearance under the toecap at the moment of impact shall be in accordance with Table 5. In addition, the toecap shall not develop any cracks which go through the material, that is, through which light can be seen.)	-	0	Clause Repeated
Cl.5.8 Upper/Outsole Bond Strength(When the footwear is tested in accordance with the method prescribed in 5.2 of IS 15298 (Part 1), the bond strength shall not be less than 4.0 N/mm, unless there is tearing of the sole in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.9 Sole Interlayer Bond Strength for Bi-polymer( and Bi-density Sole When tested in accordance with 5.2 of IS 15298 (Part 1), the bond strength between the outer or cleated layer and the adjacent layer shall not be less than 4.0 N/mm unless there is tearing of any part of the sole, in which case the bond strength shall not be less than 3.0 N/mm.)	-	0	Clause Repeated
Cl.5.10 Consolidation Test( Representative sample of width 25 ± 0.5 mm are cut out from the quarter of the upper along the length of boot. The plies are separated by breaking the bond. Carry out the test on two specimens in accordance with IS 3400 (Part 5). Th)	-	0	Clause Repeated
Cl.5.11 Compression Resistance( 5.11.1 When safety boots are tested in accordance with 5.5 of IS 15298 (Part 1), the clearance under the toe cap at a compression load of 15 kN ± 0.1 kN shall be in accordance with Table 5.)	-	0	Clause Repeated
Cl.5.12 Internal Length of Toe Cap( For safety boots, internal length of the toe cap shall meet the specification given in Table 5 of IS 15298 (Part 2) when tested as per 5.3 of IS 15298 (Part 1).)	-	0	Clause Repeated
Cl.6.1 Abrasion Resistance of Compact Outsole( When outsole is tested in accordance with 8.3 of IS 15298 (Part 1), the relative volume loss shall not be greater than 250 mm³ for materials having density 0.9 g/cm³ or less, and not greater than 150 mm³ for materials with density greater than 0.9 g/cm³.)	-	0	Clause Repeated
Cl.6.2 Flexing Resistance of Compact Outsole( When outsole is tested in accordance with 8.4 of IS 15298 (Part 1), the cut growth shall not be greater than 4 mm before 30 000 cycles.)	-	0	Clause Repeated
Cl.6.4 Resistance to Hot Contact( — Sole Heel When sole heel is tested in accordance with 8.7 of IS 15298 (Part 1), the material shall not melt/deform and shall not develop any cracks when bent around the mandrel.)	-	0	Clause Repeated
Cl.6.5 Hydrolysis( When bottom sole or other components are made out of polyurethane, the same shall be tested in accordance with 8.5 of IS 15298 (Part 1) and the same shall comply with 5.8.5 of IS 15298 (Part 2).)	-	0	Clause Repeated
4(Types)	-	0	Clause Repeated
5(Requirements)	-	0	Clause Repeated
5.10(consolidation test IS 3400 (Part 5))	-	0	Clause Repeated
5.2.8.4(Colour of the lace)	-	0	Clause Repeated
5.10(Consolidation Test IS 3400 (Part 5) : 1986)	-	0	Clause Repeated
Cl. 5.2.4(Reinforcing Material)	-	0	Clause Repeated
Cl. 5.2.8.4(Colour of the lace)	-	0	Clause Repeated
Cl. 5.3(Construction 5.3.1,5.3.3,5.3.4)	-	0	Clause Repeated
7.2(Resistance to electricity)	-	0	Clause Repeated
Cl.5.2.1.2( Composite upper material shall comply with tear strength as per 5.4.3 of IS 15298 (Part 2).)	-	0	Clause Repeated
Cl.5.2.1.3 , Cl.6.5 of IS 15298 (Part 1).( Composite upper material shall develop no cracks before 150 000 cycles when tested in accordance with 6.5 of IS 15298 (Part 1).)	-	0	Clause Repeated

-
Included w.e.f 18.12.2024

IS 16994 (2018)

Footwear for Men and Women for Municipal Scavenging Work

Footwear for Men and Women for Municipal Scavenging Wor

66200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1(Impact resistance)	-	3000	-
7.1(Compression Tester)	-	3000	-
7.3(Tear Strength )	-	1000	-
7.3(Water Vapour permeability & coefficient )	-	2000	-
7.3(Thickness )	-	300	-
7.3(Tensile Strength )	-	1000	-
7.3(Flexing Resistance )	-	4000	Rs. 2000 for belly flexing Rs. 2000 for WVP & Cofficient
7.4(Tear Strength )	-	1000	-
7.4(Tensile Strength )	-	1000	-
7.4(Abrasion Resistance)	-	2000	-
7.5(Thickness )	-	300	-
7.5(Water abrasion & desorption)	-	1000	-
7.5(Insoles )	-	500	-
7.5(Insocks )	-	2000	-
7.6(1st Dry collapsing load, hardness)	-	3000	-
7.6(Resilience test )	-	3000	-
7.6(Moisture )	-	3000	-
7.6(Shape retention)	-	3000	-
7.6(Peel Strength )	-	1000	-
7.7(Density )	-	500	-
7.7(Thickness)	-	300	-
7.7(Hardness (IRHD))	-	1500	Ageing and thickness
7.7.1(Tear Strength )	-	1000	-
7.7.2(Abrasion Resistance)	-	1000	-
7.7.3(Flexing Resistance )	-	1000	-
7.7.4(Interlayer Bond Strength )	-	1000	-
7.7.5(Upper / Outsole bond strength)	-	1000	-
7.8(Insocks Material )	-	0	-
7.9(Hydrolysis)	-	1500	-
7.10(Ageing test)	-	2500	-
8.0(Construction)	-	5000	1) Banned Chemicals (Phthalate) 2) Breaking load (Lace)
8.1(Height of upper )	-	300	-
8.2(Internal Toe cap length)	-	300	-
8.3(Impact resistance )	-	3000	-
8.3(Compression Resistance)	-	3000	-
8.4(Volatility & lead content )	-	2700	-
8.6(Leak Proof test)	-	1000	-
7.1(Impact resistance)	-	0	Clause Repeated
7.1(Compression Tester)	-	0	Clause Repeated
7.3(Tear Strength )	-	0	Clause Repeated
7.3(Water Vapour permeability & coefficient )	-	0	Clause Repeated
7.3(Thickness )	-	0	Clause Repeated
7.3(Tensile Strength )	-	0	Clause Repeated
7.3(Flexing Resistance )	-	0	Clause Repeated
7.4(Tear Strength )	-	0	Clause Repeated
7.4(Tensile Strength )	-	0	Clause Repeated
7.4(Abrasion Resistance)	-	0	Clause Repeated
7.5(Thickness )	-	0	Clause Repeated
7.5(Water abrasion & desorption)	-	0	Clause Repeated
7.5(Insoles )	-	0	Clause Repeated
7.5(Insocks )	-	0	Clause Repeated
7.6(1st Dry collapsing load, hardness)	-	0	Clause Repeated
7.6(Resilience test )	-	0	Clause Repeated
7.6(Moisture )	-	0	Clause Repeated
7.6(Shape retention)	-	0	Clause Repeated
7.6(Peel Strength )	-	0	Clause Repeated
7.7(Density )	-	0	Clause Repeated
7.7(Thickness)	-	0	Clause Repeated
7.7(Hardness (IRHD))	-	0	Clause Repeated
7.7.1(Tear Strength )	-	0	Clause Repeated
7.7.2(Abrasion Resistance)	-	0	Clause Repeated
7.7.3(Flexing Resistance )	-	0	Clause Repeated
7.7.4(Interlayer Bond Strength )	-	0	Clause Repeated
7.7.5(Upper / Outsole bond strength)	-	0	Clause Repeated
7.8(Insocks Material )	-	0	Clause Repeated
7.9(Hydrolysis)	-	0	Clause Repeated
7.10(Ageing test)	-	0	Clause Repeated
8.0(Construction)	-	0	Clause Repeated
8.1(Height of upper )	-	0	Clause Repeated
8.2(Internal Toe cap length)	-	0	Clause Repeated
8.3(Impact resistance )	-	0	Clause Repeated
8.3(Compression Resistance)	-	0	Clause Repeated
8.4(Volatility & lead content )	-	0	Clause Repeated
8.6(Leak Proof test)	-	0	Clause Repeated
7.1(Impact resistance)	-	0	Clause Repeated
7.1(Compression Tester)	-	0	Clause Repeated
7.3(Tear Strength )	-	0	Clause Repeated
7.3(Water Vapour permeability & coefficient )	-	0	Clause Repeated
7.3(Thickness )	-	0	Clause Repeated
7.3(Tensile Strength )	-	0	Clause Repeated
7.3(Flexing Resistance )	-	0	Clause Repeated
7.4(Tear Strength )	-	0	Clause Repeated
7.4(Tensile Strength )	-	0	Clause Repeated
7.4(Abrasion Resistance)	-	0	Clause Repeated
7.5(Thickness )	-	0	Clause Repeated
7.5(Water abrasion & desorption)	-	0	Clause Repeated
7.5(Insoles )	-	0	Clause Repeated
7.5(Insocks )	-	0	Clause Repeated
7.6(1st Dry collapsing load, hardness)	-	0	Clause Repeated
7.6(Resilience test )	-	0	Clause Repeated
7.6(Moisture )	-	0	Clause Repeated
7.6(Shape retention)	-	0	Clause Repeated
7.6(Peel Strength )	-	0	Clause Repeated
7.7(Density )	-	0	Clause Repeated
7.7(Thickness)	-	0	Clause Repeated
7.7(Hardness (IRHD))	-	0	Clause Repeated
7.7.1(Tear Strength )	-	0	Clause Repeated
7.7.2(Abrasion Resistance)	-	0	Clause Repeated
7.7.3(Flexing Resistance )	-	0	Clause Repeated
7.7.4(Interlayer Bond Strength )	-	0	Clause Repeated
7.7.5(Upper / Outsole bond strength)	-	0	Clause Repeated
7.8(Insocks Material )	-	0	Clause Repeated
7.9(Hydrolysis)	-	0	Clause Repeated
7.10(Ageing test)	-	0	Clause Repeated
8.0(Construction)	-	0	Clause Repeated
8.1(Height of upper )	-	0	Clause Repeated
8.2(Internal Toe cap length)	-	0	Clause Repeated
8.3(Impact resistance )	-	0	Clause Repeated
8.3(Compression Resistance)	-	0	Clause Repeated
8.4(Volatility & lead content )	-	0	Clause Repeated
8.6(Leak Proof test)	-	9	Clause Repeated

-
Included w.e.f 10.12.2024 Exclusion : Cl 8.6 Carcinogenic disperse dye Cl 8.6 Allergenic disperse dye

IS 3736 (1995)

Canvas boots, rubber sole - Specification (Second Revision)

Canvas boots, rubber sole

28687 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	200	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	200	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	200	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	250	-
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	200	-
Cl.4.1.1 upper IS 1969(b)Weft)	-	250	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	250	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	Clause Repeated
Cl.4.1.1 upper IS 1969(c) Ends/dm )	-	0	Clause Repeated
Cl.4.1.1 upper IS 1969(b)Weft)	-	250	-
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	250	-
Cl.4.1.1 upper(The upper shall consist of Rip Stop Fabric of cotton or manmade or its blend being the over layer and cotton drill as an inner layer and shall conform to the requirements given at Sl No. (i) of Table 1. Sr.no 1.Overlayer Construction )	-	0	Clause Repeated
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	1000	0
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	-
4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast to daylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454 : 1985.)	-	0	Clause Repeated
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	200	-
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	Clause Repeated
Cl.4.1.1.2( Fastness to mechanical washing (mild) shall be of rating 4 or better, when tested in accordance with IS 764 : 1979)	-	0	Clause Repeated
Cl.4.1.1 upper IS 1969(Breaking load in N.Min (5 × 20 cm grip): a) Wrap)	-	500	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	400	-
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	400	-
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	500	-
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	Clause Repeated
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	Clause Repeated
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	Clause Repeated
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	Clause Repeated
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	Clause Repeated
4.1.2 Lining Material(having 390 ± 10 ends/dm and )	-	0	Clause Repeated
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	Clause Repeated
4.1.2 Lining Material(For covering of the insole, cotton drill conforming to Table 1, Sl No. (ii) shall be used. For detachable insole, bleached cotton twill of breaking load 390 N Min in warp way and)	-	0	Clause Repeated
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	500	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	500	-
Cl.4.1.3 Binding Material IS 1954:1990(Cotton tape NEWAR used as binding material shall conform to the requirements as mentioned in Table 2, when tested in accordance with the methods referred to in col 4 of Table 2. 1)Width, mm. Min )	-	0	Clause Repeated
4.1.3(Cotton tape NEWAR)	-	1000	-
4.1.3.2(Fastness to mechanical washing (mild))	-	200	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	200	-
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	1000	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	500	-
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	Clause Repeated
Cl.4.1.4 Reinforcement Material(The back seam, joining two quarters at the back of the heel shall be reinforced with a not less than 25 mm wide tape made out of material conforming to Sl No. (i) of Table 1)	-	0	Clause Repeated
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	400	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	400	-
Cl.4.1.5 Thread for Upper Closing Cl.4.1.5.1 (IS 1670:1991)(Sewing thread cotton, man made or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirements. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other blend of thread would have breaking load not less than above referred requirement of specification.')	-	500	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	1000	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	200	-
Cl.4.1.5.2( The colour of the threads shall be asagreed to between the purchaser and the supplier. The dyed threads shall conform to the following requirements)	-	300	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	400	-
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	500	-
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	Clause Repeated
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	Clause Repeated
4.1.6 Fabric Laces Cl.4.1.6.1( The boots shall be provided with braided of cotton or man made or blended fabric laces 115 ± 5 cm in length, matching the colour of the upper. )	-	0	Clause Repeated
4.1.6 Fabric Laces Cl.4.1.6.1(The laces shall have a minimum breaking load of 450 N, when tested between 18 cm grips, the rate of traverse of power actuated grip being 30 cm/min.)	-	0	Clause Repeated
4.1.6.2(Laces- Fastness to daylight)	-	1000	-
4.1.6.3(Laces- Fastness to mechanical washing (mild))	-	200	-
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	200	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	200	-
Cl.4.1.7 Rubber Components Cl.4.1.7.1( the soles and heels shall conform to Type 2 of IS 5676:1995.)	-	200	-
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	200	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	1500	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	500	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	1000	-
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	500	-
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Tensile strength in MPa, Min)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 1) : 1987(Elongation at break, in percent, Min)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles b)Cut growth at the end of 150 000 cycles, Percent, Max)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 16) : 1974(iii)Flexing resistance, number of cycles a)Initial crack, Min)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 9) : 1978( The rubber components shall conform to Table 4 when tested.' ( Page 3, Table 4, Note 1) — 'However in case it is not possible then 4.2.5.3 of IS 13695:1993 shall be followed. 1)Relative density, Max)	-	0	Clause Repeated
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	1000	-
Cl.4.1.7.3 IS 3400 (Part 10) : 1977(Compression set, in percent. Max)	-	0	Clause Repeated
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	1500	-
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	500	-
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	Clause Repeated
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	Clause Repeated
Cl.4.1.7.4 Ageing(The boots shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the soles and heels of the boots shall conform to the physical requirements prescribed in Table 5. i) Tensile Length)	-	0	Clause Repeated
Cl.4.1.7.4 Ageing(ii) Elongation at break)	-	0	Clause Repeated
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	300	-
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	Clause Repeated
Cl.4.1.7.5 Thickness of components(Individual components of the boots shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	Clause Repeated
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	300	-
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	Clause Repeated
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	200	-
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	Clause Repeated
Cl.4.4.2( The canvas upper shall be lined with bleached drill cloth.)	-	0	Clause Repeated
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	300	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	300	-
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	Clause Repeated
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	Clause Repeated
Cl.4.4.3(The top, side and front edges of the quarters and tongue shall be bound with cotton tape NEWAR of not less than 13 mm width using variety No. 29 thread.)	-	0	Clause Repeated
Cl.4.4.3( The upper shall be stitched on a lockstitch machine, with 30 to 40 stitches per decimetre by thread of variety No. 8 and variety No. 29 cotton sewing thread conforming to 4.1.5 using variety No. 29 for taping and binding and variety No. 8 for remaining seams. )	-	0	Clause Repeated
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	300	-
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	Clause Repeated
Cl.4.4.4( The back of the quarter shall be reinforced with a strip, not less than 25 mm wide,of either upper material or canvas. In case of composite upper material the edges of the strip shall be bound by cotton tape ( NEWAR ). When canvas cloth is used the edges shall be folded and shall be stitched with two rows of stitching.)	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	200	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	200	-
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	250	-
Cl.4.4.5 ( Table 1.)(b) Weft )	-	250	-
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	300	-
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	Clause Repeated
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)(d) Picks/dm)	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)(c) Ends/dm )	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)(b) Weft )	-	0	Clause Repeated
Cl.4.4.5 ( Table 1.)( in case of half bellow. Thefull bellow tongue shall be made out of canvas cloth as prescribed in Sl No. (i) of Table 1. Breaking load in N, Min a) Warp )	-	0	Clause Repeated
Cl.4.4.5 ( The tongue shall be either half or full bellow depending on the requirement of the purchaser andshall be made from composite material prescribed for the upper in 4.1.1.)	-	0	Clause Repeated
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	200	-
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	Clause Repeated
Cl.4.4.6( A minimum of seven aluminium, brass or steel eyelets having 10 mm diameter and wall thickness 0.30 to 0.35 mm shall be fitted in each face.')	-	0	Clause Repeated
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	300	-
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	Clause Repeated
Cl.4.4.7( The toe shall be reinforced with a toe puff cemented inside and outside with rubber toe cap. The heel piece (counter) or stiffener shall be set from the bottom of the lining and bound flat on the top edge with white cloth for binding of countertop edge with white clothfor binding of counter)	-	0	Clause Repeated
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	200	-
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	Clause Repeated
Cl.4.4.8( A strengthening rubber arch piece shall be firmly pasted and stitched at the middle arch of the inside quarter. Another strengthening rubber piece, circular in shape 35 ± 1 mm in diameter, may bepasted and stitched at the centre of the inside)	-	0	Clause Repeated
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	200	-
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	Clause Repeated
Cl.4.4.9(From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine)	-	0	Clause Repeated
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	300	-
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	Clause Repeated
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	300	Clause Repeated
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	500	-
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	300	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	300	-
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	Clause Repeated
Cl.4.6 Mass(The mass of finished boots, rubber sole, of size 8 shall not exceed 1130 g per pair, and the mass shall increase or decrease by 75 g per pair for each bigger or smaller size respectively.)	-	0	Clause Repeated
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	1000	-
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	Clause Repeated
Cl.4.7 Consolidation Test(From the quarter, cut a strip of 25.0 ± 0. 5 mm width along the length of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30 N (3.0 kgf) for each of the test pieces)	-	0	Clause Repeated
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	1000	-
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	Clause Repeated
Cl.4.8 Adhesion Test(From the upper foxing portion where it is adhered to the canvas cut a strip of 8.0 ± 0.5 mm width along with the length of the sole at the waist portion and of sufficient lengh to permit separation over a length of at least 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100 ± 10 mm per minute in accordance with IS 3400 (Part 5):1986 or the Static Dead Load Method as given in Annex C. The individual adhesion value noted/recorded shall not be less than 8 N (0.8 kgf) for each of the test pieces ( see Note under 4.7 ).')	-	0	Clause Repeated
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	1000	-
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	Clause Repeated
Cl.4.9 Composite Breaking Strength Test( From the upper of made up footwear representative sample of width 25 ± 0.5 mm width strip is to be cut along the length of the boot of enough length so as to make it convenient to allow a distance of minimum 30 mm between the jaws of the tensile machine.Rate of traverse of pulling jaw shall be 100 ± 5 mm per minute. Two such test pieces will be required to be obtained from the made up footwear and will be subjected to test to break each test piece. Mean value of each set of test pieces comprising of length wise and height wise test pieces will be 1 000 N/25 mm width minimum.')	-	0	Clause Repeated
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	-
IS 1969:1985(Breaking load on 50 cm test length. N, Min)	-	0	-
Cl.4.1.1 upper IS 1969(d) Picks/dm)	-	0	Clause Repeated
Table 2 (ii)(Breaking load on 50 cm test length. N, Min)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 4) : 1987 IS 3400 (Part 2) : 1980(Change in initial hardness after accelerated ageing for 24 h at l00 ± 1°C)	-	0	Clause Repeated
Cl.4.1.7.2 IS 3400 (Part 2) : 1980(2)Hardness, IRHD)	-	0	Clause Repeated
4.1.2 Lining Material( 200 N Minin weft way (when tested in accordance with IS 1969 : 1985) )	-	0	Clause Repeated
Cl.4.1.3.3( Black tapes shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
4.1.6 Fabric Laces Cl.4.1.6.1(The two ends of the lace shall be provided with suitable metal or plastic tips. Black laces shall be free from sulphur dyes when tested in accordance with Annex B.)	-	0	Clause Repeated
Cl.4.5.1(Cl.4.1.6.)( Each pair of boot shall be provided with a pair of braided fabric laces of the quality as prescribed in 4.1.6.)	-	0	Clause Repeated
Cl.4.3 Leg Height(The leg height of the boots for size 8 shall be 160 ± 2 mm with an increase or decrease of 4 mm of the nominal height for each bigger or smaller sizes respectively when measured at the inside from the back of the boot from insole to the top.)	-	0	Clause Repeated
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	Clause Repeated
Cl.4.5.2( In appearance, general workmanship, finish and in all other respects, not defined in this standard, the boot shall be similar to those of the sample approved by the purchaser, if any.)	-	0	Clause Repeated
4.1.2 Lining Material(195 ± 5 picks/dm shall be used.)	-	0	Clause Repeated
Cl.4.4.10( A 25 mm Min wide and 2 mm Min thick rubber golosh in serrated, diamond or any otherdesign, as agreed to between the purchaser and thesupplier, shall be fitted all round the sole edge of the boot. The golosh shall not extend below the edge of the sole.)	-	0	-

-
Included w.e.f 12.11.2024

IS 17037 (2018)

Anti riot shoes - Specification

Anti riot shoes

65975 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(General)	-	0	-
4.2(Design )	-	0	-
4.3.1(Size)	-	200	-
4.3.2(Weight)	-	300	-
4.4(Height of upper )	-	200	-
4.5.1(Contruction)	-	400	-
4.5.2(Ergonomic Feature)	-	500	-
4.5.3(Bond strength)	-	0	-
4.5.3.1(Upper/outsole bond strength)	-	1000	-
4.5.3.2(Interayer bond strength)	-	1000	-
4.5.5.1(Dimension)	-	500	-
4.5.5.2(Flex resistance )	-	1500	-
4.5.5.3(Nail penetraion Insert )	-	1000	-
4.5.5.4(Ageing test)	-	9000	Corrosion resistance Effect of High Temperature Effect of Low Temperature Effect of Acid Effect of Alkali Effect of Fuel Oil
4.5.6.1(General)	-	200	-
4.5.6.2(Internal Toe cap length)	-	200	-
4.5.6.3(Impact resistance )	-	2000	-
4.5.6.4(Compression resistance)	-	1000	-
4.5.7.1(Antistatic test)	-	1000	-
4.5.8(Heat insulation of sole complex)	-	1000	-
4.5.9(Cold insulation of sole complex)	-	1000	-
4.5.10(Energy absorption of seat region )	-	1000	-
4.5.11(Thickness Toe puff & counter stiffener)	-	0	Incorrect Test Name
4.5.11(Water Resistance Tray method )	-	0	-
4.5.11(Water resistance machine method)	-	1500	-
4.6.1(Thickness )	-	7700	1000 for Clause 4.6.1 6700 for referred standard IS 5677
4.6.2(Tear Strength)	-	500	-
4.6.3(Water vapour permeability & coefficent )	-	1000	-
4.6.4(Water penetration and water absorption)	-	750	-
4.7.1(Meterial)	-	17800	Rs. 500 for Clause 5.7.1 Rs. 17300 for Clause 4.7.2 (Referred Clause IS 3840)
4.7.3(Tear Strength)	-	500	-
4.7.4(Abrasion resistance )	-	1000	-
4.7.5(Water vapour permeability & coefficent )	-	1000	-
4.8.1(Meterial)	-	200	-
4.8.2(Abrasion resistance )	-	500	-
4.8.3(Water absorption & desorption )	-	1000	-
4.9.1(Meterial)	-	500	-
4.9.2(Abrasion resistance )	-	1000	-
4.9.3(Water absorption & desorption )	-	1000	-
4.10(Counter stiffener thickness)	-	200	-
4.11.1(Thickness)	-	700	Rs. 200 for Thickness Rs. 500 for Density
4.11.2(Tear Strength)	-	500	-
4.12.1(Thickness )	-	200	-
4.12.2(Tear Strength)	-	500	-
4.13(Breaking Strength of thread)	-	500	-
4.14.1(Meterial)	-	500	-
4.14.2(Thickness )	-	200	-
4.14.3(Density )	-	500	-
4.14.4(Hardness (IRHD))	-	500	-
4.14.5(Ageing test)	-	8000	Rs. 1500 for Clause 4.14.5 Rs. 6500 For Clause 4.14.6 to 4.14.10
4.15(D-ring and Hooks )	-	200	-
4.16.1(Length of laces )	-	300	-
4.16.2(Breaking load & lag retention)	-	1000	-
5.0(Innocuosness test IS 17011)	-	26500	-
4.9(Insocks)	-	0	-
5(Chemical Requirements)	-	0	Clause Repeated
6.1(Scale of Sampling)	-	0	-
6.2(Methods of Selecting Footwear)	-	0	-
6.3.1(Visual and Tactile Examination)	-	0	-
6.3.2(Dimensional Characteristics)	-	0	-
6.3.3.1(Tests for physical requirements)	-	0	-
6.3.3.2(Tests for chemical requirements)	-	0	-
7(Marking)	-	0	-
4.4, Table 2(Shoe size)	-	0	Clause Repeated
4.4, Table 2(Height)	-	0	Clause Repeated
6.1.3, Table 3(Scale of Sampling and Permissible Number of Defectives for Tests on Whole Footwear)	-	0	-
4.14.8(Flex resistance)	-	0	Clause not available in specification
4.14.9(Resistance to hot contact)	-	0	Clause not available in specification
4.14.10(Resistance to fuel oil)	-	0	Clause not available in specification
4.14.6(Tear Strength)	-	0	Clause not available in specification
4.14.7(Abrasion resistance)	-	0	Clause not available in specification
4.1(General)	-	0	Clause Repeated
4.5.3(Bond strength)	-	0	Clause Repeated
4.12.2(Tear Strength)	-	0	Clause Repeated
4.9(Insocks)	-	0	Clause Repeated
5(Chemical Requirements)	-	0	Clause Repeated
6.1(Scale of Sampling)	-	0	Clause Repeated
6.2(Methods of Selecting Footwear)	-	0	Clause Repeated
6.3.1(Visual and Tactile Examination)	-	0	Clause Repeated
6.3.2(Dimensional Characteristics)	-	0	Clause Repeated
6.3.3.1(Tests for physical requirements)	-	0	Clause Repeated
6.3.3.2(Tests for chemical requirements)	-	0	Clause Repeated
7(Marking)	-	0	Clause Repeated
4.4, Table 2(Shoe size)	-	0	Clause Repeated
4.4, Table 2(Height)	-	0	Clause Repeated
6.1.3, Table 3(Scale of Sampling and Permissible Number of Defectives for Tests on Whole Footwear)	-	0	Clause Repeated
4.1(General)	-	0	Clause Repeated
4.5.3(Bond strength)	-	0	Clause Repeated
4.12.2(Tear Strength)	-	0	Clause Repeated
4.9(Insocks)	-	0	Clause Repeated
5(Chemical Requirements)	-	0	Clause Repeated
6.1(Scale of Sampling)	-	0	Clause Repeated
6.2(Methods of Selecting Footwear)	-	0	Clause Repeated
6.3.1(Visual and Tactile Examination)	-	0	Clause Repeated
6.3.2(Dimensional Characteristics)	-	0	Clause Repeated
6.3.3.1(Tests for physical requirements)	-	0	Clause Repeated
6.3.3.2(Tests for chemical requirements)	-	0	Clause Repeated
7(Marking)	-	0	Clause Repeated
4.4, Table 2(Shoe size)	-	0	Clause Repeated
4.4, Table 2(Height)	-	0	Clause Repeated
6.1.3, Table 3(Scale of Sampling and Permissible Number of Defectives for Tests on Whole Footwear)	-	0	Clause Repeated
4.5.4(Slip Resitance)	-	2000	-

-
Included w.e.f 17.10.2024 Excluding Cl 5.0 (Innocuosness test IS 17011) (Allergenic and carcinogenic disperse dyes)

IS 16645 (2018)

Moulded Plastics Footwear ” Lined or Unlined Polyurethane Boots for General Industrial use ” Specification

Moulded Plastics Footwear ” Lined or Unlined Polyuretha

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Soling Pattern )	-	300	-
4.2(Thickness )	-	200	-
4.3(Thickness of components )	-	0	Material and components
5.1(General )	-	0	-
5.2(Resistance to flexing of boot upper)	-	1000	-
5.3(Tesile Strength )	-	1000	-
5.4(Hardness (IRHD))	-	500	-
5.6(Resistance to soling to cut growth)	-	1000	-
5.7(Split tear strength )	-	1000	-
5.8.1(Tensile strength after Hydrolysis)	-	2500	-
5.8.2& 5.8.3(Hydrolysis )	-	2500	-

-
Included w.e.f 17.10.2024 Excluding Cl 5.5 (Cold flex temp of upper)

IS 13995 (1995)

Unlined moulded rubber boots - Specification

Unlined moulded rubber boots

6300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Thickness )	-	300	-
5.1.1(Tensile Strength (before ageing))	-	1000	-
5.1.2(Tensile Strength (after ageing))	-	2500	-
5.1.3(Tear Strength)	-	1000	-
5.1.4(Resistance to dry heat ageing )	-	500	-
5.1.5(Flexing resistance of upper)	-	1000	-
5.1.6(Design)	-	0	-
5.1.7(Size)	-	0	-
6, 6.1(Marking)	-	0	-
Cl.6, 6.1(Marking)	-	0	Clause Repeated

-
Included w.e.f. 03.10.2024

IS 13893 (1994)

Polyurethane soles semirigid - specification

Polyurethane Unit Outsoles

8300 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.3.2(Ageing test)	-	2000	-
4.3(Ross Flex test)	-	0	Clause Amended
4.3(Flexural strength )	-	0	Clause Amended
4.3(Abrasion Resistance)	-	0	Clause Amended
4.3(Elongation at break)	-	0	Clause Amended
4.3(Tensile Strength )	-	0	Clause Amended
4.3(Hardness Shore(A))	-	0	Clause Amended
4.3(Relative density )	-	0	Clause Amended
4.2(Thickness )	-	0	Clause Amended
4.1(Design)	-	0	-
5, 5.1, 5.2(Packing And Marking)	-	0	-
Cl.5, 5.1, 5.2(Packing And Marking)	-	0	Clause Repeated
4.2 (Amendment 2)(Thickness)	-	200	-
4.3.1 Table 1 i) (Amendment 2)(Relative Density)	-	500	-
4.3.1 Table 1 iii) (Amendment 2)(Abrasion Resistance at applied force of 10 N)	-	700	-
4.3.1 Table 1 iv) (Amendment 2)(Flexing Resistance, Bennewart method)	-	1000	-
4.3.1 Table 1 v) (Amendment 2)(Hydrolysis Resistance, cut growth after 150000 flexes)	-	1500	-
4.3.1 Table 1 vi) (Amendment 2)(Tensile Strength)	-	500	-
4.3.1 Table 1 vii) (Amendment 2)(Elongation at break)	-	500	-
4.3.1 Table 1 viii) (Amendment 2)(Tear Strength (average force))	-	1000	-
4.3.1 Table 1 ii) (Amendment 2)(Hardness, degree, Shore A)	-	400	-

-
Included along with Amendment No.2 w.e.f. 24.06.2024

IS 3735 (1996)

Canvas Shoes, Rubber Sole

20900 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	1000	-
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	1500	Breaking Load Ends/dm, Picks/dm
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	1000	-
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	200	-
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	1000	-
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	900	Breaking Strength Length (m/kg)
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	1600	Colour Fastness to Light Colour Fastness to Washing Colour Fastness to Perspiration
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	400	-
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	400	-
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	500	-
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	1000	-
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	4500	Relative density Hardness, IRHD Flexing resistance Change in initial hardness after accelerated ageing for24 h at 100 ± 1°C Tensile strength Elongation at break Compression set
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	1500	-
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	1500	-
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	1000	-
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	200	-
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	0	-
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	0	-
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	0	-
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	200	-
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	-
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	-
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	200	-
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	200	-
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	200	-
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	200	-
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	-
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	200	-
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	1000	-
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	500	-
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	0	Clause Repeated
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	0	Clause Repeated
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	0	Clause Repeated
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	0	Clause Repeated
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	0	Clause Repeated
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	0	Clause Repeated
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	0	Clause Repeated
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	0	Clause Repeated
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	0	Clause Repeated
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	0	Clause Repeated
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	0	Clause Repeated
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	0	Clause Repeated
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	0	Clause Repeated
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	0	Clause Repeated
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	Clause Repeated
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	0	Clause Repeated
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	0	Clause Repeated
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	0	Clause Repeated
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	0	Clause Repeated
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	0	Clause Repeated
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	Clause Repeated
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	Clause Repeated
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	0	Clause Repeated
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	0	Clause Repeated
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	0	Clause Repeated
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	0	Clause Repeated
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	Clause Repeated
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	0	Clause Repeated
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	0	Clause Repeated
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	0	Clause Repeated
Cl.4.5 Consolidation Test IS 3400 (Part 5) : 1986 (From the quarter, cut a strip of 25.0 ± 0.5 mm width along the leagth of the boot and of sufficient length to permit separation over a length of 75 mm. Carry out the test on two test pieces (one from each odd) at the rate of traverse of 100± 10mm per minute in accordance with IS 3400 (Part 5): 1986 or Static Dead Load Method as given in Annex C. The individual adhesion value for consolidation test shall not be less than 30N (3.0 kgf) for each of the teat piecea (see Note under 4.4).')	-	0	Clause Repeated
4.1.1 Upper, Sl No. (i) of Table 1(The upper shall consist of over layer of cotton, manmade or blended conforming' to the requirements given in Sl No. (i) of Table 1 as an overlayer and cotton drill conforming to the requirements given in Sl No. (ii) of Table 1, as an inner layer or lining. The two fabrics shall be firmly adhered together with rubber compound. )	-	0	Clause Repeated
Cl.4.1.1.1 Colour fastness(The dyed fabrics prescribed in 4.1.1 shall be fast todaylight and mechanical washing. Fastness to daylight shall be of rating 4 or better, when tested in accordance with IS 686 : 1985 or IS 2454: 1985. However in case of dispute the method prescribed in IS 686 : 1985 shall be considered as referee method.)	-	0	Clause Repeated
Cl.4.1.2 Binding Material(IS 1954 : 1990) (IS1969 : 1985)(Cotton tape NEWAR used as binding material shall conform to the requirements prescribed in col 3 of Table 2, when tested in accordance with the methods referred to in col 4 of the table.)	-	0	Clause Repeated
Cl.4.1.2.1 Anmex B.(Cotton, manmade or blended shall be used as binding material.' 'Coloured cotton tapes shall have fastness to day light of rating as and if agreed to between the purchaser and the supplier when tested in accordance with IS 686 : 1985. The black tapes shall be free from sulphur dyes when tested in accordance with Annex B.')	-	0	Clause Repeated
Cl.4.1.3.1( Sewing thread cotton, manmade or blended shall be used for stitching of upper. For cotton variety thread shall conform to variety No. 28 of IS 1720. Polyester variety thread shall conform to variety No. 9 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification. Sewing thread cotton, manmade or blended shall be used for binding of upper. For cotton variety thread shall conform to variety No. 32 of IS 1720. Polyester variety thread shall conform to variety No. 5 of IS 9543. Any other suitable thread shall have breaking load not less than above referred requirement of specification.')	-	0	Clause Repeated
Cl.4.1.3.2 (IS 2454 : 1985) IS 765 : 1979 IS 971 : 1966( The colour of the threads shall be as agreedto between the purchaser and the supplier. The dyed threads shall conform to the following requirements or IS 686 : 1985'.)	-	0	Clause Repeated
Cl.4.1.4(.Brass, steel or aluminium eyelets of 7.5 mm diameter and wall thickness 0.30 to 0.35 mm shall be used.')	-	0	Clause Repeated
Cl.4.1.5 Laces( The shoes shall be provided with fabric braided laces either matching the shade of the upper or black or The length of the lace shall be 60 ± 3 cm )	-	0	Clause Repeated
Cl.4.1.5 Laces(and shallhave the breaking strength of not less than 250 N when tested between 18 cm grips in accordance with IS 1969 : 1985, the rate of traverse of power actuated grip being 300 mm/min.)	-	0	Clause Repeated
Cl.4.1.5 Laces Annex B(In case the laces are black, the same shall pass the test for freedom from sulpher dyes when tested in accordance with Annex B. The two ends of the lace shall be provided with suitable metal or plastic tips.)	-	0	Clause Repeated
Cl.4.1.6 Rubber Components(The rubber components shall conform to the requirements given in Table 4, when tested from finished boots.However in case it is not possible to cut the test pieces from the made up boots then 4.1.5.3 of IS 13695 : 1993 shall be followed.')	-	0	Clause Repeated
Cl.4.1.6.2 Ageing col 4 of Table 5.(The shoes shall be also aged at 70 ± 1°C for 168 h, on completion of which the test pieces taken from the shoes shall conform to the physical requirements prescribed in col 4 of Table 5. )	-	0	Clause Repeated
Cl.4.1.6.2 Ageing (None of the rubber components of the shoes shall show any sign of tackiness or crack developed after ageing, when examined visually)	-	0	Clause Repeated
Cl.4.1.6.3 Thickness of components in Table 6.(Individual components of the shoes shall comply with the thickness and material requirements prescribed in Table 6.)	-	0	Clause Repeated
CL.4.2 Shape and Design IS 1638 : 1969(Cl 4.2.1 The shoes shall be made according to design and pattern as agreed to between the purchaser and the supplier. Size and fittings of the shoes shall be in accordance with IS 1638 : 1969 unless otherwise specified by the purchaser.)	-	0	Clause Repeated
Cl.4.2.2( The recommended design of canvas shoes is shown in Fig. 1.)	-	0	Clause Repeated
Cl.4.3 Construction Cl 4.3.1( The upper shall be stitched on a lock stitch machine and the number of stitches shall be 30 to 40 per dm.)	-	0	Clause Repeated
Cl.'4.3.2( Back of the upper shall be reinforced with a strip of upper material when there is a seam.')	-	0	Clause Repeated
Cl.4.3.3( The counter shall be stitched at the back, set from bottom of lining and bound flat on top edge with white/scoured binding material cut in bias and formed as a tape. T )	-	0	Clause Repeated
Cl.4.3.3(he number of stitches shall be 30 to 40 per decimetre. The counter binding shall meet the binding of the upper at the centre top edge of the heel.)	-	0	Clause Repeated
Cl.4.3.3(The edges of quarter shall be bound with dyed cotton binding material or matching to the colour of the upper, cut in bias and formed as a tape.)	-	0	Clause Repeated
Cl.4.3.4 (The vantp shall be strengthened with a rubber toe-cap (see Fig. 1).)	-	0	Clause Repeated
Cl.4.3.5( Five pairs of eyelets shall be fitted in each shoe. The eyelets shall be properly clenched without any distortion. It shall properly match the colour of the upper canvas, or as agreed to between the purchaser and the supplier.)	-	0	Clause Repeated
Cl.4.3.6( The shoes shall be free from folds, wrinkles in the upper, blisters, embedded foreign matters and excessive surface markings. In appearance, general workmanship, finish and all other respects, not defined in the standard, the shoes shall be similar to the sample approved by the purchaser, if any)	-	0	Clause Repeated
CL.4.3.7( The soles shall be of even substance and ofone layer only.)	-	0	Clause Repeated
Cl.4.3.8( A rubber foxing shall be fixed all round the sole and heel. The colour shall be as agreed to between the purchaser and the supplier. )	-	0	Clause Repeated
Cl.4.3.8(The foxing, not less than 18 mm wide, shall not extend beyond the edges of the sole at the bottom)	-	0	Clause Repeated
Cl.4.4 Adhesion Test(From the upper-foxing portion where it is adhered to the canvas, parallel to the waist of sole, cut a strip of length 100 mm and width 8 mm. Separate out the plies initially by breaking the bond to a length of about 75 mm. Carry out the test on two specimens in accordance with IS 3400 (Part 5) : 1986. There shall be no further separation within 1 minute at a load of 1 kg for each of the two specimens.)	-	0	Clause Repeated
CL.4.6 Mass(The mass of one pair of finished shoes of size 8 shall not exceed 750 g with an increase or decrease of 25 g for each bigger or smaller size respectively)	-	0	Clause Repeated
4.8(Adhesion )	-	0	Clause Repeated
4.7(Consolidation test )	-	0	Clause Repeated
4.6(Mass )	-	0	Clause Repeated
4.5(Finish )	-	0	-
4.4(Contruction )	-	0	Clause Repeated
4.3(Leg Height )	-	0	Test parameter not available in the specification0
4.2(Design )	-	0	Clause Repeated
4.1.6.2(Thickness of components )	-	0	Clause Repeated
4.1.6.2(Ageing)	-	0	Clause Repeated
4.1.6.2(Elongation at break after ageing )	-	0	Clause Repeated
4.1.6.2(Tensile after ageing )	-	0	Clause Repeated
4.1.6(Compression set )	-	0	Clause Repeated
4.1.6(Elongation at break )	-	0	Clause Repeated
4.1.6(Tensile strength)	-	0	Clause Repeated
4.1.6(Hardness (after accelerated ))	-	0	Clause Repeated
4.1.6(Flexing resistance test)	-	0	Clause Repeated
4.1.6(Hardness )	-	0	Clause Repeated
4.1.6(Relative density)	-	0	Clause Repeated
4.1.5(Sulpher dyes content )	-	0	Clause Repeated
4.1.5(Breaking Load )	-	0	Clause Repeated
4.1.5(Length )	-	0	Clause Repeated
4.1.4(Thickness)	-	0	Clause Repeated
4.1.3(Color fastness to perspiration)	-	0	Clause Repeated
4.1.3(Colorfastness to washing)	-	0	Clause Repeated
4.1.3(Colorfastness to light )	-	0	Clause Repeated
4.1.3(Single thread breaking load)	-	0	Clause Repeated
4.1.3(Construction )	-	0	Clause Repeated
4.1.2(Colorfastness to light )	-	0	Clause Repeated
4.1.2(Colorfastness to washing)	-	0	Clause Repeated
4.1.2(Breaking Strength )	-	0	Clause Repeated
4.1.2(Width )	-	0	Clause Repeated
4.1.1.2(Colorfastness to washing)	-	0	Clause Repeated
4.1.1.1(Colorfastness to light )	-	0	Clause Repeated
4.1.1 (Drill) (End & Picks/dm)	-	0	Clause Repeated
4.1.1 (Drill) (Colorfastness to light )	-	0	Clause Repeated
4.1.1 (canvas )(End & Picks/dm)	-	0	Clause Repeated
4.1.1 (canvas )(Breaking Load )	-	0	Clause Repeated
5, 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking)	-	0	-
" CL. 5.1, Cl. 5.2, Cl. 5.2.1, Cl. 5.2.1.1(Packing and marking ")	-	0	Clause Repeated
4.1.4(Size )	-	0	Clause Repeated

-
Included w.e.f. 03.10.2024

IS 5557 : Part 2 (2018)

All rubber gum boots and ankle boots: Part 2 occupational purposes

All rubber gum boots and ankle boots:

20625 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(CLASSIFICATION)	-	0	-
3.2(compact insole)	-	500	-
3.3(compact insole)	-	500	-
3.4(compact Outsole/heel)	-	500	-
3.5(Description lining material)	-	0	-
3.6(description occupatioanl footwear)	-	0	-
3.7(Ruber material)	-	0	-
4(Type & varity)	-	0	-
5(Design)	-	0	-
6(size & fitting)	-	200	-
7.1(lining material)	-	0	-
7.1.1(Tear strength)	-	500	-
7.1.2(Abrasion resistance)	-	1000	-
7.2(Coated bindind material)	-	1300	Width, Breaking Strength
7.3(Thread for upper closing)	-	1000	Length (Meter/Kg) Breaking Strength
7.3(Thread for upper closing - sulphur test)	-	1000	-
7.4(Use of rubber)	-	0	-
7.4.1(Physical requirement of rubber component)	-	2000	Hardness Accelerated Aging + Hardness
7.5(observation of Upper)	-	0	-
7.5.1(Tensile)	-	1000	-
7.5.2(Thickness)	-	300	-
7.5.3(Flexing Resistance)	-	1000	-
7.6(Outsole/Heel)	-	0	-
7.6.1(Out sole thickness)	-	300	-
7.6.2(out sole tear strength)	-	1000	-
7.6.3(out sole abrasion)	-	1000	-
7.6.4(out sole flexing)	-	1000	-
7.6.5(Interlayer bond strength)	-	1000	-
7.7(INSOCK Visual)	-	0	-
7.7.1(Insock thickness)	-	300	-
7.7.2(Insock abrasion)	-	1000	-
8(CONSTRUCTION)	-	0	-
8.1(Hot contact)	-	1000	-
8.2(Leak proofness)	-	1000	-
8.3(Height of upper)	-	300	-
8.4(Adhesion test)	-	500	-
8.5(Resistance to acid & alkaline)	-	1000	-
8.6(Resistance to fule oil)	-	1000	-
8.7.1(Antistatic)	-	2000	-
8.7.2(CONDUCTIVE FOOTWEAR)	-	2000	-
8.7.4(Resistance to cold)	-	2000	-
10(Finish of boots)	-	0	-
11.1(Marking)	-	0	-
11.2(Marking)	-	0	-
11.3(Marking)	-	0	-

-
Included w.e.f. 03.10.2024 Exclusion: For all types of boots except electrically insulated boots, Cl.9.1 (Allergenic disperse dyes), Cl.9.2 (carcinogenic disperse dyes)

IS 5557 (2004)

Industrial and protective rubber knee and ankle boots - Specification (Fourth Revision)

Industrial and protective rubber knee and ankle boots

16600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	2000	-
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	0	-
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	0	-
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	300	-
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	6500	Complete Table 2
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	700	-
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	3000	Impact Test, Finish, Rust Preventive
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	0	-
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	0	-
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	500	-
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	1000	-
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	1000	-
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	1000	-
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	1000	-
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	2000	-
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	300	-
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	0	Clause Repeated
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	0	Clause Repeated
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	0	Clause Repeated
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	0	Clause Repeated
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	0	Clause Repeated
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	0	Clause Repeated
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	0	Clause Repeated
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	0	Clause Repeated
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	0	Clause Repeated
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	0	Clause Repeated
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	0	Clause Repeated
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	0	Clause Repeated
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	0	Clause Repeated
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	0	Clause Repeated
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	0	Clause Repeated
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	0	Clause Repeated
5/5.1.7/5.1.7.8(REQUIREMENTS- Physical Requirements-Resistance to oil)	-	0	Clause Repeated
5/5.1.1-Fig. 1, Fig. 2 and Fig. 3(REQUIREMENTS-Design)	-	0	Clause Repeated
5/5.1.2 -IS 1638(REQUIREMENTS-Size)	-	0	Clause Repeated
5/5.1.3-Table1(REQUIREMENTS-Thickness)	-	0	Clause Repeated
5/5.1.4/5.1.4.1-Table2(REQUIREMENTS-Materials-Rubber components)	-	0	Clause Repeated
5/5.1.4/5.1.4.2(REQUIREMENTS-Materials-Fabric- accordance with IS 1969)	-	0	Clause Repeated
5/5.1.4/5.1.4.3(REQUIREMENTS-Materials-Protective Steel Toe Cap- an per IS 5852)	-	0	Clause Repeated
5/5.1.6/5.1.6.1-Fig. 1, Fig. 2, Fig. 3, .Fig. 4, Fig. 5 and Table 3.(REQUIREMENTS- Construction)	-	0	Clause Repeated
5/5.1.6/5.1.6.2(REQUIREMENTS- Construction)	-	0	Clause Repeated
5/5.1.7/5.1.7.1(REQUIREMENTS- Physical Requirements-Heat treatment- as per IS 3400 (Part 4))	-	0	Clause Repeated
5/5.1.7/5.1.7.2(REQUIREMENTS- Physical Requirements-Composite strength)	-	0	Clause Repeated
5/5.1.7/5.1.7.3-Table 4(REQUIREMENTS- Physical Requirements-Flexing endurance- as per Annex B.)	-	0	Clause Repeated
5/5.1.7/5.1.7.4(REQUIREMENTS- Physical Requirements- Leakage resistance test)	-	0	Clause Repeated
5/5.1.7/5.1.7.5(REQUIREMENTS- Physical Requirements- Consolidation test- as per IS IS 3400 (Part 5))	-	0	Clause Repeated
5/5.1.7/5.1.7.6(REQUIREMENTS- Physical Requirements- Performance test- as per Annex C)	-	0	Clause Repeated
5/5.1.7/5.1.7.7(REQUIREMENTS- Physical Requirements-Height of the boots)	-	0	Clause Repeated
5, 5.1(Requirement)	-	0	Clause Repeated
6.1(Marking)	-	0	-
6, 6.1(Packing)	-	0	-
5, 5.1(Requirement)	-	0	Clause Repeated
6.1(Marking)	-	0	Clause Repeated
6.2(Packing)	-	0	Clause Repeated

-
Included w.e.f. 24.06.2024

IS 5676 (1995)

Moulded solid rubber soles and heels - SpecificatlOn (Second Revision)

Moulded solid rubber soles and heels

9600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	300	-
5/5.1(REQUIREMENTS-General)	-	0	-
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	0	-
5/5.5- Table1(REQUIREMENTS-Thickness)	-	300	-
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	300	-
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	8700	IS 3400 Part 1, 2, 4, 9, 10, 16)
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	0	Repeated
5/5.1(REQUIREMENTS-General)	-	0	Repeated
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	0	Repeated
5/5.5- Table1(REQUIREMENTS-Thickness)	-	0	Repeated
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	0	Repeated
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	0	Repeated
5/5.3/5.3.1(REQUIREMENTS- Construction)	-	0	Repeated
5/5.1(REQUIREMENTS-General)	-	0	Repeated
5/5.2- Fig. 1 to 5(REQUIREMENTS-Design)	-	0	Repeated
5/5.5- Table1(REQUIREMENTS-Thickness)	-	0	Repeated
5/5.6/5.6.1(REQUIREMENTS-Channel)	-	0	Repeated
5/5.7- Table2(REQUIREMENTS- Physical Requirements- as per IS 3400 (Part 1, Part 2, Part 4, Part 9, Part 10, Part 16))	-	0	Repeated
6(Marking and packing)	-	0	Repeated
8.1(Test methods)	-	0	Repeated
8.3(Measurement of thickness)	-	0	Repeated
Cl.6.1,6.2,6.3(Marking and packing)	-	0	Repeated
8.1(Test Methods)	-	0	Repeated
Cl.8.3(Measurement of thickness ")	-	0	Repeated
5.5 (Amendment 1)(Thickness)	-	0	Repeated
5.7 Table 2 i) (Amendment 1)(Relative Density)	-	0	Repeated
5.7, Table 2 ii) (Amendment 1)(Hardness, degree, Shore A)	-	0	Repeated
5.7, Table 2 iv) (Amendment 1)(Abrasion Resistance at applied force of 10 N)	-	0	Repeated
5.7, Table 2 v) (Amendment 1)(Tensile strength)	-	0	Repeated
5.7, Table 2 vi) (Amendment 1)(Elongation at break)	-	0	Repeated
5.7, Table 2 vii) (Amendment 1)(Tear strength (average force))	-	0	Repeated
5.7, Table 2 iii) (Amendment 1)(Flexing resistance)	-	0	Repeated

-
Included w.e.f. 03.10.2024

IS 6664 (1992)

Rubber microcellular sheets for soles and heels - Specification (First Revision)

Microcellular Rubber Sheets for Outsoles

8950 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4, Cl.4.1,4.1.1,4.1.2(Requirements)	-	0	-
Cl.4 Cl.4.1.3 And 8.3,Table1, i)(Relative density)	-	500	-
Cl.4.1.3 And 8.3,Table1, iii)(Hardness, Shore A durometer min)	-	500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iii)(Change in Hardness after ageing at 100±1°C for 24hr)	-	1500	-
Cl.4 Cl.4.1.3 And 8.3,Table1, iv)(Compression set at constant stress percent, Max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, v)(Split tear strength, kg,Min)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, vi)(Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, vi)(Heat shrinkage test at 100±1°C for 1 hour max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table1, viii)(Water absorption , percent by mass, Max)	-	1000	-
Cl.4 Cl.4.1.3 And 8.3,Table 1, viii)(Flexing resistance: Maximum cut growth at 50 000 cycles)	-	1000	-
4.2(Flexing resistance )	-	0	Clause Repeated
4.2(Water absorption)	-	0	Wrong test description
4.2(Heat Shrinkage )	-	0	Clause Repeated
4.2(Shrinkage at room temp)	-	0	Clause Repeated
4.2(Split tear strength)	-	0	Clause Repeated
4.2(Compression set)	-	0	Clause Repeated
4.2(Hardness (Shore A))	-	0	Clause Repeated
4.2(Density )	-	0	Clause Repeated
4.2(Size & Thickness )	-	0	-
5, 5.1(Marking)	-	0	-
6, 6.1(Packing)	-	0	-
"Cl.4 ,Cl.4.1,4.1.1,4.1.2(Requirements ")	-	0	Clause Repeated
Cl.4.1.3 And 8.3,Table1(i) Relative density)	-	500	-
Cl.4.1.3 And 8.3,Table1(ii) Hardness, Shore A durometer min)	-	500	-
Cl.4.1.3 And 8.3,Table1(iii) Change in Hardness after ageing at 100±1°C for 24hr)	-	0	Clause Repeated
Cl.4.1.3 And 8.3,Table1(iv) Compression set at constant stress percent, Max)	-	1000	-
Cl.4.1.3 And 8.3,Table1(vi) Room Temperature shrinkage at 27±2°C for 2weeks, percent, Max)	-	0	Clause Repeated
Cl.4.1.3 And 8.3,Table 1 vi(Heat shrinkage test at 100±1°C for 1 hour max)	-	0	Clause Repeated
Cl.4.1.3 And 8.3,Table1(ix)Flexing resistance)	-	0	Clause Repeated
5, 5.1(Marking)	-	0	Clause Repeated
6, 6.1(Packing)	-	0	Clause Repeated
Cl.4.1.3 And 8.3,Table1(viii)Water absorption , percent by mass, Max)	-	0	Clause Repeated

-
Table-1 (Compression set at constant stress) scope restsricted to method B of Annex-D of IS 10702 Included along with Amendment No.1 w.e.f. 24.06.2024

IS 6719 (1972)

Solid Pvc Soles And Heels

4750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	0	-
3.6 (i)(Relative density )	-	500	-
3.6 (ii)(Tensile Strength )	-	750	-
3.6 (iii)(Elongation at break, percent )	-	750	-
3.6 (iv)(Tear Strength a) Force Part b) Back Part )	-	750	-
3.6 (v)(Volatility, percent by means )	-	500	-
3.6 (vi)(Lead (as Pb) ppm)	-	1000	-
3.6.1(Hardness )	-	500	-
6 ,6.1,6.2,6.3(Test Method)	-	0	-
Cl. 6.4(Measurement of thickness)	-	0	-
Cl. 3.1,3.2,3.3,3.4,3.5(Material)	-	0	-

-
Included along with Amendment No.1 w.e.f. 24.06.2024

IS 15298 : part 4 (2017)

Personal protective equipment: Part 4 occupational footwear (Second Revision)

Occupational Footwear

54200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1(CLASS I)	-	200	-
Table 1(CLASS II)	-	200	-
5.2.2.1(General)	-	500	-
5.2.2.2(Height of upper)	-	300	-
5.2.2.3(Seat region)	-	300	-
5.3.2.1(Construction)	-	300	-
5.3.1.2(Upper/outsole bond strength)	-	700	-
5.3.2.2(Leakproofness)	-	500	-
5.3.2.3(Specific ergonomic features )	-	1000	-
5.3.2.5(Innocuousness )	-	26500	-
5.4.2.1(Upper)	-	300	-
5.4.2.2(Thickness )	-	300	-
5.4.2.3(Tear strenth)	-	500	-
5.4.2.4(Tensile properties)	-	500	-
5.4.2.5(Flexing resistance )	-	1000	-
5.4.2.6(Water vapour permeability and coefficient )	-	700	-
5.4.2.7(pH value )	-	500	-
5.4.2.8(Hydrolysis)	-	3500	-
5.4.2.9(Chromium VI content )	-	750	-
5.5.2.1(Tear strength )	-	500	-
5.5.2.2(Abrasion resistance )	-	700	-
5.5.2.3(Water vapour permeability and coefficient )	-	700	-
5.5.2.4(pH value )	-	500	-
5.5.2.5(Chromium VI content )	-	750	-
5.6(Tongue )	-	0	-
5.6.2.1(Tear strength )	-	500	-
5.6.2.2(pH value )	-	500	-
5.6.2.3(Chromium VI content )	-	750	-
5.7.2.1(Insole and insock )	-	300	-
5.7.2.2(Insole and insock )	-	500	-
5.7.2.3(Water absorption and desorption )	-	500	-
5.7.4.1(Abrasion resistance )	-	400	-
5.7.4.2(Abrasion resistance )	-	700	-
5.7.2.5(Chromium VI content )	-	750	-
5.8.2.1(Outsole)	-	0	-
5.8.1.1(Thickness )	-	300	-
5.8.1.2(Cleated area )	-	300	-
5.8.1.3(Cleat height)	-	300	-
5.8.2.2(Tear strength )	-	500	-
5.8.2.3(Abrasion resistance )	-	700	-
5.8.2.4(Flexing resistance )	-	700	-
5.8.2.5(Hydrolysis )	-	3500	-
5.8.2.6(Interlayer bond strength )	-	700	-
6.2.1.1(Metallic anti-penetration insert )	-	1000	-
6.2.1.1.2(Non-metallic anti-penetration insert used as an insole)	-	1000	-
6.2.1.2(Construction)	-	200	-
6.2.1.3(Dimensions )	-	300	-
6.2.1.4(Flex resistance of penetration-resistant inserts )	-	2500	-
6.2.1.5.1(Corrosion resistance of penetration-resistant metallic inserts)	-	500	-
6.2.1.5.2(Penetration-resistant non-metallic inserts)	-	1000	-
6.2.2.1(Conductive footwear)	-	1000	-
6.2.2.2(Antistatic footwear)	-	1000	-
6.2.3.1(Heat insulation of sole complex )	-	700	-
6.2.3.2(Cold insulation of sole complex)	-	700	-
6.2.2.4(Energy absorption of seat region )	-	2000	-
6.2.2.5(Water resistance )	-	500	-
6.2.7.1(Cut resistance foot wear)	-	0	-
6.2.7.2(Cut resistance foot wear)	-	0	-
6.2.7.3(Resistance to cutting)	-	2500	-
6.2.7.4(Pentration resistance)	-	1000	-
6.3.2.2(Upper- water penetration)	-	1000	-
6.4.2.1(Resistance to hot contact)	-	700	-
6.4.2.2(Resistance to fuel oil)	-	700	-
7(a)(Marking)	-	0	-
7(b)(Marking)	-	0	-
7(c)(Marking)	-	0	-
7(d)(Marking)	-	0	-
7(e)(Marking)	-	0	-
7(e)(Marking)	-	0	-
Table 1(CLASS I)	-	0	Clause Repeated
Table 1(CLASS II)	-	0	Clause Repeated
5.2.2.1(General)	-	0	Clause Repeated
5.2.2.2(Height of upper)	-	0	Clause Repeated
5.2.2.3(Seat region)	-	0	Clause Repeated
5.3.2.1(Construction)	-	0	Clause Repeated
5.3.1.2(Upper/outsole bond strength)	-	0	Clause Repeated
5.3.2.2(Leakproofness)	-	0	Clause Repeated
5.3.2.3(Specific ergonomic features )	-	0	Clause Repeated
5.3.2.5(Innocuousness )	-	0	Clause Repeated
5.4.2.1(Upper)	-	0	Clause Repeated
5.4.2.2(Thickness )	-	0	Clause Repeated
5.4.2.3(Tear strenth)	-	0	Clause Repeated
5.4.2.4(Tensile properties)	-	0	Clause Repeated
5.4.2.5(Flexing resistance )	-	0	Clause Repeated
5.4.2.6(Water vapour permeability and coefficient )	-	0	Clause Repeated
5.4.2.7(pH value )	-	0	Clause Repeated
5.4.2.8(Hydrolysis)	-	0	Clause Repeated
5.4.2.9(Chromium VI content )	-	0	Clause Repeated
5.5.2.1(Tear strength )	-	0	Clause Repeated
5.5.2.2(Abrasion resistance )	-	0	Clause Repeated
5.5.2.3(Water vapour permeability and coefficient )	-	0	Clause Repeated
5.5.2.4(pH value )	-	0	Clause Repeated
5.5.2.5(Chromium VI content )	-	0	Clause Repeated
5.6(Tongue )	-	0	Clause Repeated
5.6.2.1(Tear strength )	-	0	Clause Repeated
5.6.2.2(pH value )	-	0	Clause Repeated
5.6.2.3(Chromium VI content )	-	0	Clause Repeated
5.7.2.1(Insole and insock )	-	0	Clause Repeated
5.7.2.2(Insole and insock )	-	0	Clause Repeated
5.7.2.3(Water absorption and desorption )	-	0	Clause Repeated
5.7.4.1(Abrasion resistance )	-	0	Clause Repeated
5.7.4.2(Abrasion resistance )	-	0	Clause Repeated
5.7.2.5(Chromium VI content )	-	0	Clause Repeated
5.8.2.1(Outsole)	-	0	Clause Repeated
5.8.1.1(Thickness )	-	0	Clause Repeated
5.8.1.2(Cleated area )	-	0	Clause Repeated
5.8.1.3(Cleat height)	-	0	Clause Repeated
5.8.2.2(Tear strength )	-	0	Clause Repeated
5.8.2.3(Abrasion resistance )	-	0	Clause Repeated
5.8.2.4(Flexing resistance )	-	0	Clause Repeated
5.8.2.5(Hydrolysis )	-	0	Clause Repeated
5.8.2.6(Interlayer bond strength )	-	0	Clause Repeated
6.2.1.1(Metallic anti-penetration insert )	-	0	Clause Repeated
6.2.1.1.2(Non-metallic anti-penetration insert used as an insole)	-	0	Clause Repeated
6.2.1.2(Construction)	-	0	Clause Repeated
6.2.1.3(Dimensions )	-	0	Clause Repeated
6.2.1.4(Flex resistance of penetration-resistant inserts )	-	0	Clause Repeated
6.2.1.5.1(Corrosion resistance of penetration-resistant metallic inserts)	-	0	Clause Repeated
6.2.1.5.2(Penetration-resistant non-metallic inserts)	-	0	Clause Repeated
6.2.2.1(Conductive footwear)	-	0	Clause Repeated
6.2.2.2(Antistatic footwear)	-	0	Clause Repeated
6.2.3.1(Heat insulation of sole complex )	-	0	Clause Repeated
6.2.3.2(Cold insulation of sole complex)	-	0	Clause Repeated
6.2.2.4(Energy absorption of seat region )	-	0	Clause Repeated
6.2.2.5(Water resistance )	-	0	Clause Repeated
6.2.7.1(Cut resistance foot wear)	-	0	Clause Repeated
6.2.7.2(Cut resistance foot wear)	-	0	Clause Repeated
6.2.7.3(Resistance to cutting)	-	0	Clause Repeated
6.2.7.4(Pentration resistance)	-	0	Clause Repeated
6.3.2.2(Upper- water penetration)	-	0	Clause Repeated
6.4.2.1(Resistance to hot contact)	-	0	Clause Repeated
6.4.2.2(Resistance to fuel oil)	-	0	Clause Repeated
7(a)(Marking)	-	0	Clause Repeated
7(b)(Marking)	-	0	Clause Repeated
7(c)(Marking)	-	0	Clause Repeated
7(d)(Marking)	-	0	Clause Repeated
7(e)(Marking)	-	0	Clause Repeated
7(e)(Marking)	-	0	Clause Repeated
5.3.4.1(Slip resistance)	-	2000	-
5.3.4.2(Slip resistance on ceramic tile floor with sodium lauryl sulphate (SLS) solution)	-	0	Inclusive in Clause 5.3.4.1
5.3.4.3(Slip resistance on steel floor with glycerine )	-	0	Inclusive in Clause 5.3.4.1
5.3.4.4(Slip resistance on ceramic tile floor with SLS and on steel floor with glycerine )	-	0	Inclusive in Clause 5.3.4.1

-
Included w.e.f. 03.10.2024 Exclusion: for all types of footwear except electrically insulated footwear, ankle protection footwear, Cl.5.3.2.5 innocuousness allergenic and carcinogenic disperse dyes

IS 15298 : Part 3 (2019)

Personal protective equipment: Part 3 protective footwear (Second Revision)

Protective footwear

41475 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.2 Table-2(Height of upper)	-	300	-
5.2.3 Table-2(Seat Region)	-	300	-
5.3.1.1 Table-2(Construction)	-	300	-
5.3.1.2 Table-2(Upper/Outsole Bond)	-	700	-
Table-2(Strength)	-	0	-
5.3.2.1 Table-2(General)	-	300	-
5.3.2.2 Table-2(Internal Length of toe cap)	-	300	-
5.3.2.3 Table-2(Impact Resistance -T- )	-	700	-
5.3.2.4 Table-2(Compression)	-	700	-
5.3.2.5 Table-2(Behaviour of toe cap)	-	500	-
5.3.3 Table-2(Leak Proofness)	-	500	-
5.3.4 Table-2(Specific Ergonomic)	-	1000	-
Table-2(Features)	-	0	-
Table-2(0.18)	-	26500	5.3.6 (Innocuousness)
5.4.1 Table-2(General)	-	300	-
5.4.2 Table-2(Thickness)	-	300	-
5 4 3 Table-2(Tear Strength)	-	500	-
5.4.4 Table-2(Tensile Properties)	-	500	-
5.4.5 Table-2(Flexing Resistance)	-	1000	-
5.4.6 Table-2(Water Vapour Permeability & Coefficient)	-	700	-
5 4.7 Table-2( )	-	500	-
5 4.8 Table-2(Hydrolysis)	-	3500	-
5.4 9 Table-2(Chrome VI)	-	750	-
5.5.1 Table-2(Tear Strength)	-	500	-
5.5.2 Table-2(Abrasion Resistance)	-	700	-
5.5.3 Table-2(Water Vapour Permeability & Coefficient)	-	700	-
5.5.4 Table-2(pH Value)	-	500	-
5.5.5 Table-2(Chrome VI)	-	750	-
5.6.1 Table-2(Tear Strength)	-	500	-
5.6.2 Table-2(pH Value)	-	500	-
5.6.3 Table-2(Chromium VI)	-	750	-
5.7.1 Table-3(Thickness)	-	300	-
5.7.2 Table-3(pH Value)	-	500	-
5.7.3 Table-3(Water Absorption &)	-	500	-
5.7.4.1 Table-3(Insole Abrasion)	-	400	-
5.7.4.2 Table-3(Abrasion)	-	700	-
5.7.5 Table-3(Chromium VI)	-	750	-
5.8.1 Table-2(Design)	-	900	Thickness, Cleat Height, Cleat Area
5.8.2 Table-2(Tear Strength)	-	500	-
5.8.3 Table-3(Abrasion Resistance)	-	700	-
5.8.4 Table-3(Flexing Resistance)	-	700	-
5.8.5 Table-3(Hydrolysis)	-	3500	-
5.8.6 Table-2(Interlayer BondStrength)	-	700	-
6.2.1 Table-I8(Penetration Resistance)	-	1000	-
6.2.2.1 Table-18(Electrical Properties)	-	0	-
Table-18(Conductive Footwear)	-	1000	-
6.2.2.2 Table-18(Antistatic Footwear)	-	1000	-
6.2.3.1 Table-18(Heat Insulated Comp)	-	700	-
6.2.3.2 Table-18(Cold Insulated)	-	700	-
6.2.4 Table-18(Energy Absorption of seat region)	-	2000	-
6.2.5 Table-18(Water Resistance)	-	500	-
6.2.7 Table-18(Ankle Protection)	-	0	-
6.2.8 Table-18(Cut Resistance)	-	2500	-
6.3 Table-18(Water Penetration & Absorption)	-	1000	-
6.4.1 Table-18(Resistance to Hot Contact)	-	700	-
6.4.2 Table-18(Resistance to Fuel oil)	-	700	-
Cl.4, Table1, Annex A ISO 20344 :2011(Classification and designs)	-	0	Clause Repeated
Cl. 5,Cl.5.1Table 2, Table 3(General)	-	0	Clause Repeated
Cl. 5.2, Cl.5.2.1, Figure 3,(General)	-	0	Clause Repeated
8(Information to be supplied)	-	0	Clause Repeated
Cl.8.1 IS 15298 Part 3:2018, ISO 20346 :2014(General)	-	0	Clause Repeated
8.2(Electrical properties)	-	0	Clause Repeated
8.2.1(Conductive footwear)	-	0	Clause Repeated
8.2.2(Antistatic footwear)	-	0	Clause Repeated
8.3(Insocks)	-	0	Clause Repeated
Cl.5.8.1.3(Cleat Height)	-	0	Clause Repeated
Cl.5.8.1.2(Cleated area)	-	0	Clause Repeated
Cl.5.8.1.1(Table 17 Thickness)	-	0	Clause Repeated
Table-3(Desorption)	-	0	Clause Repeated
6.2.7 Table-18(Ankle Protection)	-	0	Clause Repeated
6.2.8 Table-18(Cut Resistance)	-	0	Clause Repeated
Cl.4, Table1, Annex A ISO 20344 :2011(Classification and designs)	-	0	Clause Repeated
Cl. 5,Cl.5.1Table 2, Table 3(General)	-	0	Clause Repeated
Cl. 5.2, Cl.5.2.1, Figure 3,(General)	-	0	Clause Repeated
8(Information to be supplied)	-	0	Clause Repeated
Cl.8.1 IS 15298 Part 3:2018, ISO 20346 :2014(General)	-	0	Clause Repeated
8.2(Electrical properties)	-	0	Clause Repeated
8.2.1(Conductive footwear)	-	0	Clause Repeated
8.2.2(Antistatic footwear)	-	0	Clause Repeated
8.3(Insocks)	-	0	Clause Repeated
Cl.5.8.1.3(Cleat Height)	-	0	Clause Repeated
Cl.5.8.1.2(Cleated area)	-	0	Clause Repeated
Cl.5.8.1.1(Table 17 Thickness)	-	0	Clause Repeated
5.3.5.2 Table-2(Slip Resistance SRA)	-	0	Clause Repeated
5.3.5.3 Table-2(Slip Resistance SRB)	-	0	Clause Repeated
Cl.5.3.5.1, Cl.5.3.5.2,Cl.5.3.5.3 or 5.3.5.4 IS 15298 (Part1):2015,ISO 20344:2011,5.11(General)	-	2000	-
5.3.5.4 Table-2(Slip Resistance SRC)	-	0	Inclusive Cl. 5.3.5.1, 5.3.5.2, 5.3.5.3, 5.3.5.4
Cl. 6.2.6 Table 18(Metatarsal Protection)	-	2000	-

-
Included w.e.f. 03.10.2024 Exclusion: for all types of footwear except electrically insulated footwear, ankle protection footwear, Cl.5.3.6 innocuousness allergenic and carcinogenic disperse dyes

Bureau of Indian Standards

The National Standards Body of India

Testtex India Laboratories Private Limited, Noida

C - 57, Sector - 65, Noida, Gautam Buddha Nagar, Uttar Pradesh, 201301

9821318289 labsindianoida@testtex.com

Scope List

No Record Found