BIS - LIMS (Laboratory Information Management System)

Gravitas Laboratories Private Limited, Greater Noida

Plot No. 95, Udyog Vihar Extn, Ecotech II, Surajpur I.A., Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201306

7042049001 testinggravitas@gmail.com

Scope List

Reset

162 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 4270 (2001)

Steel tubes used for water wells specification (Third Revision)

All Grade

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Tensile Test & Flattening Test)	-	5500	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	1000	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	1000	-
Cl 10(Outer Diameter & Overall Length)	-	1000	-
Cl 12(Bituminous Coating & Galvanizing )	-	1500	-
Cl 14(Workmanship)	-	1000	-
Cl 6(Tensile Test & Flattening Test)	-	0	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	0	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	0	-
Cl 10(Outer Diameter & Overall Length)	-	0	-
Cl 12(Bituminous Coating & Galvanizing )	-	0	-
Cl 14(Workmanship)	-	0	-
Cl 6(Tensile Test & Flattening Test)	-	0	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	0	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	0	-
Cl 10(Outer Diameter & Overall Length)	-	0	-
Cl 12(Bituminous Coating & Galvanizing )	-	0	-
Cl 14(Workmanship)	-	0	-
5.2(phosphorus)	-	11000	-
5.2(sulphur)	-	11000	-
Cl 14(Workmanship)	-	0	-
Cl 12(Bituminous Coating & Galvanizing )	-	0	-
Cl 10(Outer Diameter & Overall Length)	-	0	-
Cl 9(Pipe ends, Angle of bevel & Root Face )	-	0	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	0	-
Cl 6(Tensile Test & Flattening Test)	-	0	-
Cl 6(Tensile Test & Flattening Test)	-	0	-
Cl 7(Outer Diameter, Thickness, Mass & Straightness)	-	0	-
Cl 9(Pipe ends, Angle of bevel & Root Face)	-	0	-
Cl 10(Outer Diameter & Overall Length)	-	0	-
Cl 12(Bituminous Coating & Galvanizing)	-	0	-
Cl 14(Workmanship)	-	0	-
11.0(Alignment test IS 4270: 2001)	-	0	-
Cl. 8(Hydrostatic test)	-	0	-

-
Included w.e.f. 04.11.2025 Exclusion: Cl. 8 (Hydrostatic test)

IS 5517 (1993)

Steels for hardening and tempering - Speicification (Second Revision)

All Designation

44000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Aluminium IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Boron- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Tin- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	12000	-
5(Freedom from defects , IS 5517)	-	1000	-
8,Table 6(Hardness Test - IS 1500(Pt -1))	-	1000	-
9, Table 5(Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-	6000	-
10(Grain Size - IS 4748)	-	9000	-
11.1(Inclusion Rating- IS 4163)	-	9000	-
11.2(Blue Fracture Test - IS 10138 (Pt1))	-	9000	-
11.2(Step Down Test- IS 10138(Pt2))	-	0	-
11.2(Magnetic Particle Test -- IS 10138(Pt3))	-	0	4500
12;Table 7(Hardenability Test-IS 3848)	-	14000	-
13.1&13.2&13.3(Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-	1000	-
16.1 a)(Additional Test; Macro etch Test)	-	0	-
16.1 b)(Additional Test; Ultrasonic Test -IS 3664)	-	0	-
16.1 c); Table 7(Additional Test;Hardenability Test)	-	0	-
16.1 d);Table 5(Additional Test;Blank Hardening Test)	-	0	-
16.1 e)(Additional Test;Cleanliness Test-IS 10138(Pt 1to3))	-	0	-
16.1 f)(Microstructure for machinability,including banding)	-	0	-
16.1 g)(Hot up set for forgability)	-	0	-
Cl 6.2 & Table 2(Carbon- IS 228(Part 1))	-	0	-
Cl 6.2 & Table 3(Sulphur- IS 228(Part 9))	-	0	-
Cl 6.2 & Table 4(Phosphorous- IS 228(Part 3))	-	0	-
Cl 6.2 & Table 5(Manganese- IS 228(Part 2))	-	0	-
Cl 6.2 & Table 6(Silicon- IS 228(Part 2))	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Aluminium IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Boron- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Tin- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
5(Freedom from defects , IS 5517)	-	0	-
8,Table 6(Hardness Test - IS 1500(Pt -1))	-	0	-
9, Table 5(Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-	0	-
10(Grain Size - IS 4748)	-	0	-
11.1(Inclusion Rating- IS 4163)	-	0	-
11.2(Blue Fracture Test - IS 10138 (Pt1))	-	0	-
11.2(Step Down Test- IS 10138(Pt2))	-	0	-
11.2(Magnetic Particle Test -- IS 10138(Pt3))	-	0	-
12;Table 7(Hardenability Test-IS 3848)	-	0	-
13.1&13.2&13.3(Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-	0	-
16.1 a)(Additional Test; Macro etch Test)	-	0	-
16.1 b)(Additional Test; Ultrasonic Test -IS 3664)	-	0	-
16.1 c); Table 7(Additional Test;Hardenability Test)	-	0	-
16.1 d);Table 5(Additional Test;Blank Hardening Test)	-	0	-
16.1 e)(Additional Test;Cleanliness Test-IS 10138(Pt 1to3))	-	0	-
16.1 f)(Microstructure for machinability,including banding)	-	0	-
16.1 g)(Hot up set for forgability)	-	0	-
Cl 6.2 & Table 2(Carbon- IS 228(Part 1))	-	0	-
Cl 6.2 & Table 3(Sulphur- IS 228(Part 9))	-	0	-
Cl 6.2 & Table 4(Phosphorous- IS 228(Part 3))	-	0	-
Cl 6.2 & Table 5(Manganese- IS 228(Part 2))	-	0	-
Cl 6.2 & Table 6(Silicon- IS 228(Part 2))	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Aluminium IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Boron- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
Cl. 6.1, 6.2, 6.3, 11.2, 15.1 & Table 2(Tin- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	0	-
5(Freedom from defects , IS 5517)	-	0	-
8,Table 6(Hardness Test - IS 1500(Pt -1))	-	0	-
9, Table 5(Mechanical ptoperties - IS 1608(Pt -1),IS 1598)	-	0	-
10(Grain Size - IS 4748)	-	0	-
11.1(Inclusion Rating- IS 4163)	-	0	-
11.2(Blue Fracture Test - IS 10138 (Pt1))	-	0	-
11.2(Step Down Test- IS 10138(Pt2))	-	0	-
11.2(Magnetic Particle Test -- IS 10138(Pt3))	-	0	-
12;Table 7(Hardenability Test-IS 3848)	-	0	-
13.1&13.2&13.3(Dimensional tolerances- IS 3739 and is 3469(Pt 1to 3); Tolerance on straightness)	-	0	-
16.1 a)(Additional Test; Macro etch Test)	-	0	-
16.1 b)(Additional Test; Ultrasonic Test -IS 3664)	-	0	-
16.1 c); Table 7(Additional Test;Hardenability Test)	-	0	-
16.1 d);Table 5(Additional Test;Blank Hardening Test)	-	0	-
16.1 e)(Additional Test;Cleanliness Test-IS 10138(Pt 1to3))	-	0	-
16.1 f)(Microstructure for machinability,including banding)	-	0	-
16.1 g)(Hot up set for forgability)	-	0	-
Cl 6.2 & Table 2(Carbon- IS 228(Part 1))	-	0	-
Cl 6.2 & Table 3(Sulphur- IS 228(Part 9))	-	0	-
Cl 6.2 & Table 4(Phosphorous- IS 228(Part 3))	-	0	-
Cl 6.2 & Table 5(Manganese- IS 228(Part 2))	-	0	-
Cl 6.2 & Table 6(Silicon- IS 228(Part 2))	-	0	-

-
Included w.e.f 22.01.2026 "11.2 (Step Down Test- IS 10138(Pt2)) 16.1 d);Table 5 (Additional Test; Blank Hardening Test) 16.1 g) (Hot up set for forgability)"

IS 2002 (2024)

Steel Plate for Pressure Vessel for Intermediate and High Temperature Service Including Boilers â Specification (Fourth Revision)

All Grade

22500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General requirements)	-	0	-
Cl-6(Manufacture)	-	0	-
Cl-7.1, Table-1(Carbon)	-	9000	-
Cl-7.1, Table-1(Manganese)	-	9000	-
Cl-7.1, Table-1(Silicon)	-	9000	-
Cl-7.1, Table-1(Sulphur)	-	9000	-
Cl-7.1, Table-1(Phosphorus)	-	9000	-
Cl-8(HEAT TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	1000	-
Cl-9.2.3(Repair by Welding)	-	0	-
Cl-10.2(Rolling Mass)	-	1000	-
Cl-11(CALCULATION OF MASS)	-	500	-
Cl-13(TENSILE TEST)	-	5500	-
Cl-13.2, Table-3(Tensile Strength)	-	5500	-
Cl-13.2, Table-3(Yield Stress)	-	5500	-
Cl-13.2, Table-3(Percent Elongation on Gauge Length)	-	5500	-
Cl-14(BEND TEST)	-	5500	-
Cl-16(ULTRASONIC TESTING)	-	0	If agreed additional charge 5500/-
Cl-18(RE-TEST)	-	0	-
Cl-19(RUST PROTECTIONS)	-	0	-
Cl-20(TOLERANCES ON DIMENSIONS AND SHAPE)	-	0	-
Cl-21(Marking)	-	0	-
Cl-4.1(General requirements)	-	0	-
Cl-6(Manufacture)	-	0	-
Cl-7.1, Table-1(Carbon)	-	0	-
Cl-7.1, Table-1(Manganese)	-	0	-
Cl-7.1, Table-1(Silicon)	-	0	-
Cl-7.1, Table-1(Sulphur)	-	0	-
Cl-7.1, Table-1(Phosphorus)	-	0	-
Cl-8(HEAT TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	0	-
Cl-9.2.3(Repair by Welding)	-	0	-
Cl-10.2(Rolling Mass)	-	0	-
Cl-11(CALCULATION OF MASS)	-	0	-
Cl-13(TENSILE TEST)	-	0	-
Cl-13.2, Table-3(Tensile Strength)	-	0	-
Cl-13.2, Table-3(Yield Stress)	-	0	-
Cl-13.2, Table-3(Percent Elongation on Gauge Length)	-	0	-
Cl-14(BEND TEST)	-	0	-
Cl-16(ULTRASONIC TESTING)	-	0	Same as above
Cl-18(RE-TEST)	-	0	-
Cl-19(RUST PROTECTIONS)	-	0	-
Cl-20(TOLERANCES ON DIMENSIONS AND SHAPE)	-	0	-
Cl-21(Marking)	-	0	-

-
Included w.e.f 08.12.2025

IS 2041 (2024)

Steel Plates and Strips for Pressure Vessels Used at Moderate and Low Temperature â Specification (Fourth Revision)

All Grade

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(General requirements)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7.1, Table-1(C)	-	9000	-
Cl-7.1, Table-1(Si)	-	9000	-
Cl-7.1, Table-1(Mn Max)	-	9000	-
Cl-7.1, Table-1(P max)	-	9000	-
Cl-7.1, Table-1(S Max)	-	9000	-
Cl-7.1, Table-1(Al Max)	-	9000	-
Cl-7.1, Table-1(N Max)	-	9000	-
Cl-7.1, Table-1(Nb Max)	-	9000	-
Cl-7.1, Table-1(V Max)	-	9000	-
Cl-7.1, Table-1(Ti Max)	-	9000	-
Cl-7.1, Table-1(Nb + V + Ti Max)	-	9000	-
Cl-7.1, Table-1(Cr Max)	-	9000	-
Cl-7.1, Table-1(Cu Max)	-	9000	-
Cl-7.1, Table-1(Mo Max)	-	9000	-
Cl-7.1, Table-1(Ni Max)	-	9000	-
Cl-7.2, Table-2(Carbon)	-	0	-
Cl-7.2, Table-2(Silicon)	-	0	-
Cl-7.2, Table-2(Manganese)	-	0	-
Cl-7.2, Table-2(Phosphorus)	-	0	-
Cl-7.2, Table-2(Sulphur)	-	0	-
Cl-7.2, Table-2(Niobium)	-	0	-
Cl-7.2, Table-2(Vanadium)	-	0	-
Cl-7.2, Table-2(Titanium)	-	0	-
Cl-7.2, Table-2(Chromium)	-	0	-
Cl-7.2, Table-2(Copper)	-	0	-
Cl-7.2, Table-2(Molybdenum)	-	0	-
Cl-7.2, Table-2(Nickel)	-	0	-
Cl-8(HEAT-TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	1000	-
Cl-9.3(Edge Imperfection)	-	1000	-
Cl-10(width ( average of 3))	-	1000	-
Cl-11(THEORETICAL MASS)	-	1000	-
Cl-12.1.1(Number of Tests)	-	0	-
Cl-12.1.2(Orientation of Test Sample)	-	0	-
Cl-12.1.3(Location of Test Sample)	-	0	-
Cl-12.1.6(Tensile Test Result)	-	5500	-
Cl-12.2(Bend Test)	-	1000	-
Cl-12.3.1(Charpy impact test)	-	5500	-
Cl-12.3.2(Number of Tests)	-	0	-
Cl-12.3.3(Orientation)	-	0	-
Cl-12.5(Re-heat Treatment)	-	0	-
Cl-13(ULTRASONIC TESTING)	-	0	-
Cl-14(RUST PROTECTION)	-	0	-
Cl-15(MARKING)	-	0	-
Cl-4.1(General requirements)	-	0	-
Cl-6(MANUFACTURE)	-	0	-
Cl-7.1, Table-1(C)	-	0	-
Cl-7.1, Table-1(Si)	-	0	-
Cl-7.1, Table-1(Mn Max)	-	0	-
Cl-7.1, Table-1(P max)	-	0	-
Cl-7.1, Table-1(S Max)	-	0	-
Cl-7.1, Table-1(Al Max)	-	0	-
Cl-7.1, Table-1(N Max)	-	0	-
Cl-7.1, Table-1(Nb Max)	-	0	-
Cl-7.1, Table-1(V Max)	-	0	-
Cl-7.1, Table-1(Ti Max)	-	0	-
Cl-7.1, Table-1(Nb + V + Ti Max)	-	0	-
Cl-7.1, Table-1(Cr Max)	-	0	-
Cl-7.1, Table-1(Cu Max)	-	0	-
Cl-7.1, Table-1(Mo Max)	-	0	-
Cl-7.1, Table-1(Ni Max)	-	0	-
Cl-7.2, Table-2(Carbon)	-	0	-
Cl-7.2, Table-2(Silicon)	-	0	-
Cl-7.2, Table-2(Manganese)	-	0	-
Cl-7.2, Table-2(Phosphorus)	-	0	-
Cl-7.2, Table-2(Sulphur)	-	0	-
Cl-7.2, Table-2(Niobium)	-	0	-
Cl-7.2, Table-2(Vanadium)	-	0	-
Cl-7.2, Table-2(Titanium)	-	0	-
Cl-7.2, Table-2(Chromium)	-	0	-
Cl-7.2, Table-2(Copper)	-	0	-
Cl-7.2, Table-2(Molybdenum)	-	0	-
Cl-7.2, Table-2(Nickel)	-	0	-
Cl-8(HEAT-TREATMENT)	-	0	-
Cl-9(FREEDOM FROM DEFECTS)	-	0	-
Cl-9.3(Edge Imperfection)	-	0	-
Cl-10(width ( average of 3))	-	0	-
Cl-11(THEORETICAL MASS)	-	0	-
Cl-12.1.1(Number of Tests)	-	0	-
Cl-12.1.2(Orientation of Test Sample)	-	0	-
Cl-12.1.3(Location of Test Sample)	-	0	-
Cl-12.1.6(Tensile Test Result)	-	0	-
Cl-12.2(Bend Test)	-	0	-
Cl-12.3.1(Charpy impact test)	-	0	-
Cl-12.3.2(Number of Tests)	-	0	-
Cl-12.3.3(Orientation)	-	0	-
Cl-12.5(Re-heat Treatment)	-	0	-
Cl-13(ULTRASONIC TESTING)	-	0	-
Cl-14(RUST PROTECTION)	-	0	-
Cl-15(MARKING)	-	0	-
CL 10(Thickness ( average 10 ))	-	0	-

-
Included w.e.f 13.11.2025

IS 5518 (1996)

Steels for die blocks for drop forging - Specification (Second Revision)

All Designation

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Molybdenum)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Nickel )	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Chromium)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Phosphorus)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Sulphur)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Silicon)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Manganese)	-	12000	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Carbon)	-	12000	-
6(Freedom from defects)	-	12000	-
9(Hardness)	-	12000	-
12(Dimensional Tolerances)	-	12000	-
14(Ultasonic Test)	-	0	ON REQUEST 5500/-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	12000	-
6(Freedom from defects)	-	0	-
9(Hardness)	-	0	-
12(Dimensional Tolerances)	-	0	-
14(Ultasonic Test)	-	0	-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	0	-
"Clause 7.1 to 7.3 and 11.1 Table 1 T55Ni7Cr4Mo5VI T55Ni7Cr3Mo3VI"(Vanadium)	-	0	-
Clause 12(Dimension Tolerance)	-	0	-
Clause 14(Ultrasonic Testing)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Molybdenum)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Nickel )	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Chromium)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Phosphorus)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Sulphur)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Silicon)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Manganese)	-	0	-
Clause No.7.1 to 7.3 and 11.1 Table 1 and 2(Carbon)	-	0	-
6(Freedom from defects)	-	0	-
9(Hardness)	-	0	-
12(Dimensional Tolerances)	-	0	-
14(Ultasonic Test)	-	0	-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	0	-
6(Freedom from defects)	-	0	-
9(Hardness)	-	0	-
12(Dimensional Tolerances)	-	0	-
14(Ultasonic Test)	-	0	-
16(Marking)	-	0	-
15(a) Macro etch test in accordance with IS 11371 : 1985; b) Cleanliness test as per IS 10138 (Part 1) : 1992, IS 10138 (Part 2) : 1983 and IS 10138 (Part 3) : 1983; and c) Distribution of carbides as per IS 12211 : 1987.)	-	0	-
"Clause 7.1 to 7.3 and 11.1 Table 1 T55Ni7Cr4Mo5VI T55Ni7Cr3Mo3VI"(Vanadium)	-	0	-
Clause 12(Dimension Tolerance)	-	0	-
Clause 14(Ultrasonic Testing)	-	0	-

-
Included w.e.f 13.11.2025

IS 7092 : Part 1 (1992)

Aluminium alloy tubes for irrigation purposes - Specification: Part 1 welded tubes (Second Revision)

All Designation

16500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
10(Marking)	-	0	-
5(Workmanship and Finish)	-	4000	-
8(Dimensions)	-	4500	-
7.2(Mechanical properties)	-	4000	-
7.3(Flattening test)	-	4000	-
7.4(Hydrostatic test)	-	0	(Testing Charge 16000)
10(Marking)	-	0	-
5(Workmanship and Finish)	-	0	-
8(Dimensions)	-	0	-
7.2(Mechanical properties)	-	0	-
7.3(Flattening test)	-	0	-
7.4(Hydrostatic test)	-	0	-
10(Marking)	-	0	-
5(Workmanship and Finish)	-	0	-
8(Dimensions)	-	0	-
7.2(Mechanical properties)	-	0	-
7.3(Flattening test)	-	0	-
7.4(Hydrostatic test)	-	0	-

-
Included w.e.f 09.10.2025

IS 17682 (2021)

ALUMINIUM COMPOSITE PANEL SPECIFICATION

Grade 1, Grade 2 and Grade 2S

141500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 6(DIMENSIONS AND TOLERANCE)	-	1500	-
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	1500	-
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	1500	-
"Clause 7.1 Table 2(iii)"(Yield strength)	-	1500	-
"Clause 7.1 Table 2(iv)"(Elongation)	-	1500	-
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	1500	-
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	1500	-
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	2500	-
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	2500	-
"Clause 7.1 Table 3(v)"(Gloss)	-	1500	-
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	10000	4000 Hr Grade 1 (680000), 1000 Hr grade 2 and 2S (580000) Salt Spray Test: Up to 48 Hr (10000), Beyond 48 Hr - Up to 720 Hr (250000)
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	20000	-
Clause 6(DIMENSIONS AND TOLERANCE)	-	0	-
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	0	-
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	0	-
"Clause 7.1 Table 2(iii)"(Yield strength)	-	0	-
"Clause 7.1 Table 2(iv)"(Elongation)	-	0	-
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	0	-
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	0	-
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	0	-
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	0	-
"Clause 7.1 Table 3(v)"(Gloss)	-	0	-
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	0	-
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	0	-
Clause 6.1(Normal dimensions)	-	0	-
"Clause 7.1 Table 2(i)"(Density of core, g/cm)	-	0	-
"Clause 7.1 Table 2(ii)"(Tensile strength,)	-	0	-
"Clause 7.1 Table 2(iii)"(Yield strength)	-	0	-
"Clause 7.1 Table 2(iv)"(Elongation)	-	0	-
"Clause 7.1 Table 2(v)"(Peel strength, N/10 mm width, Min)	-	0	-
"Clause 7.1 Table 3(ii)"(Coating thickness)	-	0	-
"Clause 7.1 Table 3(iii)"(Adhesion (cross hatch))	-	0	-
"Clause 7.1 Table 3(iv)"(Pencil hardness, Min)	-	0	-
"Clause 7.1 Table 3(v)"(Gloss)	-	0	-
"Clause 7.1 Table 3(vi)"(Weatherometer test (for 4 000 h))	-	0	0
"Clause 7.1 Table 3(vii)"(Chemical resistance)	-	0	-
Cl-6.2(Thickness)	-	0	-
Cl-6.3(Tolerances)	-	0	-
Cl-5.3(Adhesive)	-	0	-
Cl-6(Edge straightness, Max)	-	0	-
Cl-6(Squareness, Max)	-	0	-

-
-

IS 7328 (2020)

Specification for Polyethylene Material for Moulding and Extrusion ( Third Revision )

45000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2.1.1(Density)	-	45000	-
5.2.1.2(MFI)	-	45000	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at yield)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at yield)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at break)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at break)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec7)(Flexural modulas)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec23)(Tear Strength)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec6)(Dart Impact strength)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec4)(Izod/Charpy impact strength)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec11)(Shore Aor D hardness)	-	0	-
5.3.2 Table 6 IS 13360 (Part 11/Sec1)(Coeffiicient of friction)	-	0	-
5.3.2 Table 6 IS 13360 (Part 6/Sec3)(Heat deflection temperature)	-	0	-
5.3.2 Table 6 IS 13360 (Part 6/Sec1)(Vicat softening temperature)	-	0	-
5.3.2 Table 6 IS 13360 (Part 6/Sec11)(Brittleness Temperature)	-	0	-
Annex B of IS 4984 5.3.2 Table6(Oxidation induction time)	-	0	-
IS 3396(Surface resistivity)	-	0	-
IS 3397(Volume resistivity)	-	0	-
IS2584(Dielectric strength)	-	0	-
IS 4486(Dissipation factor)	-	0	-
5.5.6 IS 2530(Carbon black dispersion)	-	45000	-
IS 4486(Relative permittivity)	-	0	-
5.4.3 10 ofIS 2530(Carbon black content)	-	45000	-
IS 13360(part8/Sec1)(Water absorption)	-	0	-
5.4.35 15 ofIS 2530(Colour fastness to daylight)	-	45000	-
5.4.2 13 ofIS 2530(Colour fastness to water)	-	45000	-
5.4.1 12 of IS 2530(Colour bleeding)	-	45000	-
IS 13360(part 8/Sec9)(ESCR)	-	0	-
IS 13360(part 9/Sec10)(Colour bleeding)	-	0	-
Annex C of IS4984(Volatile content)	-	0	-
IS 2530(Colour fastness to daylight)	-	45000	-
IS13360(part8/sec 6/ASTMD 1434(Gas permeability)	-	0	-
ISO 51505-2(Oxygen gas transmission rate)	-	0	-
ISO 2528(Water vopour transmission rate)	-	0	-
IS 13360(part 9/Sec9)/ASTME313(Yellowness index or whiteness index)	-	0	-
4 of IS 7016 (part 8)(Oven ageing)	-	0	-
IS 13360(part 9/Sec8)(Transparency)	-	0	-
IS15827(Natural/artificial weathering)	-	600000	-
IS 13360(part 9/Sec7)(Specular gloss)	-	0	-
IS 13360(part 9/Sec5)(Haze or luminious transmittance)	-	0	-
4.2.5.1,5.2.1.1-Table-1(Density,Kg/m3 of IS 13360 (Part 3/Sec 10)/ IS 13360 (Part 3/Sec 11) / ASTM D 1505 / ASTM D 792 / ASTM D4703,IS 13360(Part 2/Sec 1)/ ASTM D 4703/ 3.4.2 of ISO 17855-1/ 5.1.3 of IS 2530.)	-	0	-
4.2.5.2,5.2.1.2-Table-2,3(Melt flow index,g/10 min of IS 13360 (Part 4/Sec l)/ ASTM D 1238)	-	0	-
5.4.1(Colour Bleeding of 12 of IS 2530)	-	10000	-
5.4.2(Colour Fastness to Water of 13 of IS 2530)	-	45000	-
5.4.3(Colour Fastness to Daylight of 15 of IS 2530)	-	45000	-
5.4.5(Carbon Black Content for Black Compound of 10 of IS 2530 Carbon Black Content for Black ,%)	-	45000	-
5.5.6(Dispersion of Carbon Black for Black Compound of IS 2530)	-	45000	-
5.5.1(All additives used in the material which is meant for usage in contact with foodstuffs, pharmaceuticals and drinking water are given in IS 16738 for guidance purpose.)	-	0	-
5.5.2(When the products are used in contact with foodstuffs, pharmaceuticals and drinking water, its requirements with respect to the material shall also be met as per 3.3, 3.4 and 3.5 of IS 10146.)	-	0	-
Clause 6.4.2(Pigments and colourants, IS 9833, Annex D.1)	-	0	-
Clause 6.4.2(Overall Migration, IS 9845, Annex D.2)	-	0	-
5.3.2-Table 6-1(a)(Tensile strength at yield of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(b)(Tensile strength at break of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(c)(Elongation at break of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(d)(Elongation at yield of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(e)(Flexural modulus of IS 13360 (Part 5/ Sec 7))	-	0	-
5.3.2-Table 6-1(f)(Tear strength (elmendorf) of IS 13360 (Part 5/ Sec 23))	-	0	-
5.3.2-Table 6-1(g)(Dart Impact strength of IS 13360 (Part 5/ Sec 6))	-	0	-
5.3.2-Table 6-1(h)(Izod/Charpy impact strength of IS 13360 (part 5/ Sec 4) and IS 13360 (Part 5/ Sec5))	-	0	-
5.3.2-Table 6-1(j)(Shore A or D hardness of IS 13360 (part 5/ Sec 11))	-	0	-
5.3.2-Table 6-1(k)(Coefficient of friction (COF) of IS 13360 (Part 11/ Sec 1))	-	0	-
5.3.2-Table 6-2(a)(Heat deflection temperature of IS 13360 (Part 6/ Sec 3) and IS 13360 (Part 6/ Sec 17))	-	0	-
5.3.2-Table 6-2(b)(Vicat softening temperature of IS 13360 (Part 6/ Sec 1))	-	0	-
5.3.2-Table 6-2(c)(Brittleness temperature of IS 13360 (Part 6/ Sec 11))	-	0	-
5.3.2-Table 6-2(d)(Oxidation induction time of Annex B of IS 4984)	-	0	-
5.3.2-Table 6-3(e)(Surface resistivity of IS 3396)	-	0	-
5.3.2-Table 6-3(a)(Volume resistivity of IS 3396)	-	0	-
5.3.2-Table 6-3(b)(Dielectric strength of IS 2584)	-	0	-
5.3.2-Table 6-3(c)(Dissipation factor of IS 4486)	-	0	-
5.3.2-Table 6-3(d)(Relative permittivity of IS 4486)	-	0	-
5.3.2-Table 6-4(a)(Water absorption of IS 13360 (Part 8/ Sec 1))	-	0	-
5.3.2-Table 6-4(b)(Environmental stress crack resistance of IS 13360 (Part 8/ Sec 9))	-	0	-
5.3.2-Table 6-4(c)(Volatile content of Annex C of IS 4984)	-	0	-
5.3.2-Table 6-4(d)(Gas permeability IS 13360 (Part 8/ Sec 6)/ ASTM D 1434)	-	0	-
5.3.2-Table 6-4(e)(Oxygen gas transmission rate of ISO 15105-2)	-	0	-
5.3.2-Table 6-4(f)(Water vapour transmission rate of ISO 2528)	-	0	-
5.3.2-Table 6-5(a)(Oven ageing of 4 of IS 7016 (Part 8))	-	0	-
5.3.2-Table 6-5(b)(Natural/artificial weathering of IS 15827)	-	0	-
5.3.2-Table 6-6(a)(Haze and/or luminious transmittance of IS 13360 (Part 9/ Sec 5))	-	0	-
5.3.2-Table 6-6(b)(Specular gloss of IS 13360 (Part 9/ Sec 7))	-	0	-
5.3.2-Table 6-6(c)(Transparency of IS 13360 (Part 9/ Sec 8))	-	0	-
5.3.2-Table 6-6(d)(Yellowness index and/or whiteness Index of IS 13360 (Part 9/ Sec 9)/ ASTM E 313)	-	0	-
5.3.2-Table 6-6(e)(Colour fastness to daylight of IS 2530)	-	0	-
5.3.2-Table 6-6(f)(Colour bleeding of IS 13360 (Part 9/ Sec 10))	-	0	-
5.2.1.1(Density)	-	0	-
5.2.1.2(MFI)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at yield)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at yield)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Tensile strength at break)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec1)(Elongation at break)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec7)(Flexural modulas)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec23)(Tear Strength)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec6)(Dart Impact strength)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec4)(Izod/Charpy impact strength)	-	0	-
5.3.2 Table 6 IS 13360 (Part 5/Sec11)(Shore Aor D hardness)	-	0	-
5.3.2 Table 6 IS 13360 (Part 11/Sec1)(Coeffiicient of friction)	-	0	-
5.3.2 Table 6 IS 13360 (Part 6/Sec3)(Heat deflection temperature)	-	0	-
5.3.2 Table 6 IS 13360 (Part 6/Sec1)(Vicat softening temperature)	-	0	-
5.3.2 Table 6 IS 13360 (Part 6/Sec11)(Brittleness Temperature)	-	0	-
Annex B of IS 4984 5.3.2 Table6(Oxidation induction time)	-	0	-
IS 3396(Surface resistivity)	-	0	-
IS 3397(Volume resistivity)	-	0	-
IS2584(Dielectric strength)	-	0	-
IS 4486(Dissipation factor)	-	0	-
5.5.6 IS 2530(Carbon black dispersion)	-	0	-
IS 4486(Relative permittivity)	-	0	-
5.4.3 10 ofIS 2530(Carbon black content)	-	0	-
IS 13360(part8/Sec1)(Water absorption)	-	0	-
5.4.35 15 ofIS 2530(Colour fastness to daylight)	-	0	-
5.4.2 13 ofIS 2530(Colour fastness to water)	-	0	-
5.4.1 12 of IS 2530(Colour bleeding)	-	0	-
IS 13360(part 8/Sec9)(ESCR)	-	0	-
IS 13360(part 9/Sec10)(Colour bleeding)	-	0	-
Annex C of IS4984(Volatile content)	-	0	-
IS 2530(Colour fastness to daylight)	-	0	-
IS13360(part8/sec 6/ASTMD 1434(Gas permeability)	-	0	-
ISO 51505-2(Oxygen gas transmission rate)	-	0	-
ISO 2528(Water vopour transmission rate)	-	0	-
IS 13360(part 9/Sec9)/ASTME313(Yellowness index or whiteness index)	-	0	-
4 of IS 7016 (part 8)(Oven ageing)	-	0	-
IS 13360(part 9/Sec8)(Transparency)	-	0	-
IS15827(Natural/artificial weathering)	-	0	-
IS 13360(part 9/Sec7)(Specular gloss)	-	0	-
IS 13360(part 9/Sec5)(Haze or luminious transmittance)	-	0	-
4.2.5.1,5.2.1.1-Table-1(Density,Kg/m3 of IS 13360 (Part 3/Sec 10)/ IS 13360 (Part 3/Sec 11) / ASTM D 1505 / ASTM D 792 / ASTM D4703,IS 13360(Part 2/Sec 1)/ ASTM D 4703/ 3.4.2 of ISO 17855-1/ 5.1.3 of IS 2530.)	-	0	-
4.2.5.2,5.2.1.2-Table-2,3(Melt flow index,g/10 min of IS 13360 (Part 4/Sec l)/ ASTM D 1238)	-	0	-
5.4.1(Colour Bleeding of 12 of IS 2530)	-	0	-
5.4.2(Colour Fastness to Water of 13 of IS 2530)	-	0	-
5.4.3(Colour Fastness to Daylight of 15 of IS 2530)	-	0	-
5.4.5(Carbon Black Content for Black Compound of 10 of IS 2530 Carbon Black Content for Black ,%)	-	0	-
5.5.6(Dispersion of Carbon Black for Black Compound of IS 2530)	-	0	-
5.5.1(All additives used in the material which is meant for usage in contact with foodstuffs, pharmaceuticals and drinking water are given in IS 16738 for guidance purpose.)	-	0	-
5.5.2(When the products are used in contact with foodstuffs, pharmaceuticals and drinking water, its requirements with respect to the material shall also be met as per 3.3, 3.4 and 3.5 of IS 10146.)	-	0	-
Clause 6.4.2(Pigments and colourants, IS 9833, Annex D.1)	-	0	-
Clause 6.4.2(Overall Migration, IS 9845, Annex D.2)	-	0	-
5.3.2-Table 6-1(a)(Tensile strength at yield of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(b)(Tensile strength at break of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(c)(Elongation at break of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(d)(Elongation at yield of IS 13360 (Part 5/ Sec 1))	-	0	-
5.3.2-Table 6-1(e)(Flexural modulus of IS 13360 (Part 5/ Sec 7))	-	0	-
5.3.2-Table 6-1(f)(Tear strength (elmendorf) of IS 13360 (Part 5/ Sec 23))	-	0	-
5.3.2-Table 6-1(g)(Dart Impact strength of IS 13360 (Part 5/ Sec 6))	-	0	-
5.3.2-Table 6-1(h)(Izod/Charpy impact strength of IS 13360 (part 5/ Sec 4) and IS 13360 (Part 5/ Sec5))	-	0	-
5.3.2-Table 6-1(j)(Shore A or D hardness of IS 13360 (part 5/ Sec 11))	-	0	-
5.3.2-Table 6-1(k)(Coefficient of friction (COF) of IS 13360 (Part 11/ Sec 1))	-	0	-
5.3.2-Table 6-2(a)(Heat deflection temperature of IS 13360 (Part 6/ Sec 3) and IS 13360 (Part 6/ Sec 17))	-	0	-
5.3.2-Table 6-2(b)(Vicat softening temperature of IS 13360 (Part 6/ Sec 1))	-	0	-
5.3.2-Table 6-2(c)(Brittleness temperature of IS 13360 (Part 6/ Sec 11))	-	0	-
5.3.2-Table 6-2(d)(Oxidation induction time of Annex B of IS 4984)	-	0	-
5.3.2-Table 6-3(e)(Surface resistivity of IS 3396)	-	0	-
5.3.2-Table 6-3(a)(Volume resistivity of IS 3396)	-	0	-
5.3.2-Table 6-3(b)(Dielectric strength of IS 2584)	-	0	-
5.3.2-Table 6-3(c)(Dissipation factor of IS 4486)	-	0	-
5.3.2-Table 6-3(d)(Relative permittivity of IS 4486)	-	0	-
5.3.2-Table 6-4(a)(Water absorption of IS 13360 (Part 8/ Sec 1))	-	0	-
5.3.2-Table 6-4(b)(Environmental stress crack resistance of IS 13360 (Part 8/ Sec 9))	-	0	-
5.3.2-Table 6-4(c)(Volatile content of Annex C of IS 4984)	-	0	-
5.3.2-Table 6-4(d)(Gas permeability IS 13360 (Part 8/ Sec 6)/ ASTM D 1434)	-	0	-
5.3.2-Table 6-4(e)(Oxygen gas transmission rate of ISO 15105-2)	-	0	-
5.3.2-Table 6-4(f)(Water vapour transmission rate of ISO 2528)	-	0	-
5.3.2-Table 6-5(a)(Oven ageing of 4 of IS 7016 (Part 8))	-	0	-
5.3.2-Table 6-5(b)(Natural/artificial weathering of IS 15827)	-	0	-
5.3.2-Table 6-6(a)(Haze and/or luminious transmittance of IS 13360 (Part 9/ Sec 5))	-	0	-
5.3.2-Table 6-6(b)(Specular gloss of IS 13360 (Part 9/ Sec 7))	-	0	-
5.3.2-Table 6-6(c)(Transparency of IS 13360 (Part 9/ Sec 8))	-	0	-
5.3.2-Table 6-6(d)(Yellowness index and/or whiteness Index of IS 13360 (Part 9/ Sec 9)/ ASTM E 313)	-	0	-
5.3.2-Table 6-6(e)(Colour fastness to daylight of IS 2530)	-	0	-
5.3.2-Table 6-6(f)(Colour bleeding of IS 13360 (Part 9/ Sec 10))	-	0	-

-
Included w.e.f 16.09.2025

IS 17927 : Part 1 (2022)

PLASTICS ETHYLENE-VINYL ACETATE EVA MOULDING AND EXTRUSION MATERIALS PART 1 DESIGNATION SYSTEM AND SPECIFICATIONS

35000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1, Table-1(Vinyl Acetate Content, % IS 13601, ISO 8985)	-	35000	-
6.2, Table-4 & 5(Melt Mass Flow Rate, IS 17927,Part-2)	-	35000	-
6.3.2.1(Pigments and colourants, IS 9833)	-	0	-
6.3.2.2(Overall migration, mg/dm² IS 9845)	-	35000	-
6.1, Table-1(Vinyl Acetate Content, % IS 13601, ISO 8985)	-	0	-
6.2, Table-4 & 5(Melt Mass Flow Rate, IS 17927,Part-2)	-	0	-
6.3.2.1(Pigments and colourants, IS 9833)	-	0	-
6.3.2.2(Overall migration, mg/dm² IS 9845)	-	0	-
6.1, Table-1(Vinyl Acetate Content, % IS 13601, ISO 8985)	-	0	-
6.2, Table-4 & 5(Melt Mass Flow Rate, IS 17927,Part-2)	-	0	-
6.3.2.1(Pigments and colourants, IS 9833)	-	0	-
6.3.2.2(Overall migration, mg/dm² IS 9845)	-	0	-
6.1, Table-1(Vinyl Acetate Content, % IS 13601, ISO 8985)	-	0	-
6.2, Table-4 & 5(Melt Mass Flow Rate, IS 17927,Part-2)	-	0	-
6.3.2.1(Pigments and colourants, IS 9833)	-	0	-
6.3.2.2(Overall migration, mg/dm² IS 9845)	-	0	-

-
Included w.e.f 09.10.2025

IS 1361 (1978)

Specification for Steel Windows for Industrial Buildings

All Designation

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(HANDING)	-	0	-
Cl. No.4(DESIGNATION)	-	0	-
Cl. No.5(STANDARD SIZES AND TOLERANCES)	-	14000	-
Cl. No.6(MATERIAL)	-	25000	(If requested, separate sample to be supplied).
Cl. No.7(CONSTRUCTION)	-	14000	-
Cl. No.8(HOLES FOR FIXING, COUPLING AND GLAZING)	-	14000	-
Cl. No.9(FITTINGS AND FIXING MATERIALS)	-	14000	-
Cl. No.10(COMPOSITE WINDOWS)	-	14000	-
Cl. No.11, Table no. 1(GLASS)	-	14000	-
Cl. No.12(FINISH)	-	14000	-
Cl. No.3(HANDING)	-	0	-
Cl. No.4(DESIGNATION)	-	0	-
Cl. No.5(STANDARD SIZES AND TOLERANCES)	-	0	-
Cl. No.6(MATERIAL)	-	0	-
Cl. No.7(CONSTRUCTION)	-	0	-
Cl. No.8(HOLES FOR FIXING, COUPLING AND GLAZING)	-	0	-
Cl. No.9(FITTINGS AND FIXING MATERIALS)	-	0	-
Cl. No.10(COMPOSITE WINDOWS)	-	0	-
Cl. No.11, Table no. 1(GLASS)	-	0	-
Cl. No.12(FINISH)	-	0	-

-
Included w.e.f 01.09.2025

IS 1038 (1983)

Specification For Steel Doors, Windows And Ventilators

All Type

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1.(Size-Height)	-	8000	-
4.1(Size-Width)	-	8000	-
4.3(Designation)	-	0	-
5(Material-Rolled Steel Section)	-	0	-
5(Material-Coupling Section)	-	0	-
5(Material-Glass Panels)	-	0	-
5(Material-Screws)	-	0	-
6.1(Frames)	-	8000	-
6.1.1.1(Visual Inspection Test)	-	8000	-
6.1.1.1(Visual Inspection Test)	-	8000	-
6.1.1.1(Visual Inspection Test)	-	8000	-
6.1.1.2(Macro Examination)	-	8000	-
6.1.1.3(Micro Examination)	-	8000	-
6.1.1.4(Fillet Weld Test)	-	8000	-
6.2(Side Hung Shutter)	-	8000	-
6.2(Side Hung Shutter)	-	8000	-
6.2(Side Hung Shutter- Thickness of hinge)	-	8000	-
6.2(Side Hung Shutter- Pin diameter)	-	8000	-
6.2(Side Hung Shutter-Width of hinge)	-	8000	-
6.2.2 & 6.2.2.1(Handle and Handle Plate-Material of handel )	-	8000	-
6.2.2 & 6.2.2.1(Handle and Handle Plate- Thicknesss of handle)	-	8000	-
6.2.2 & 6.2.2.1(Handle and Handle Plate-Material of handel plate)	-	8000	-
6.2.2 & 6.2.2.1(Handle and Handle Plate)	-	8000	-
6.2.2 & 6.2.2.1(Handle and Handle Plate)	-	8000	-
6.2.2 & 6.2.2.1(Handle and Handle Plate-Height of handle plate)	-	8000	-
6.2.3(Peg Stay - Material)	-	0	-
6.2.3(Peg Stay - Thickness)	-	8000	-
6.2.3(Peg Stay )	-	8000	-
6.2.3(Peg Stay - Dimensions-A)	-	8000	-
6.2.3(Peg Stay - Dimensions-B)	-	8000	-
6.2.3(Peg Stay - Dimensions-C)	-	8000	-
6.2.3(Peg Stay - Dimensions-D)	-	8000	-
6.2.3(Peg Stay - Dimensions-E)	-	8000	-
6.2.3(Peg Stay - Dimensions-F)	-	8000	-
6.2.3(Peg Stay - Dimensions-G)	-	8000	-
6.2.3(Peg Stay - Dimensions-H)	-	8000	-
6.2.3(Peg Stay - Dimensions-J)	-	8000	-
6.2.3(Peg Stay - Dimensions-K)	-	8000	-
6.2.3(Peg Stay - Dimensions-L)	-	8000	-
6.2.3(Peg Stay - Dimensions-M)	-	8000	-
6.3(Top Hung Ventilator)	-	8000	-
6.3(Top Hung Ventilator)	-	8000	-
6.3(Top Hung Ventilator-Thickness of hinge)	-	8000	-
6.3(Top Hung Ventilator-Pin diameter)	-	8000	-
6.3(Top Hung Ventilator-Width of hinge)	-	8000	-
7.1(Position of Holes)	-	8000	-
7.2 Table 2(Position of Fixing Screws)	-	8000	-
7.2 Table 2(Lugs-A)	-	0	-
7.2 Table 2(Lugs-B)	-	0	-
7.2 Table 2(Lugs-C)	-	0	-
7.2 Table 2(Lugs-D)	-	0	-
7.2 Table 2(Lugs-E)	-	0	-
7.2 Table 2(Lugs-F)	-	0	-
7.2 Table 2(Lugs-G)	-	0	-
8(Finish)	-	8000	-
9(Glazing)	-	0	-
9(Glazing- No of glazing clip against each plate)	-	0	-

-
Included w.e.f 01.09.2025

IS 9282 (2024)

Wire Ropes and Strands for General Structural Applications Including Cable Supported Bridges - Specification (third revision)

All Type

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4.1(Material)	-	6000	-
Cl-4.2.1(Dimensional Limits and Tolerances)	-	6000	-
Cl-4.2.2(Tensile Test)	-	6000	-
Cl-4.2.3(tensile strength)	-	6000	-
Cl-4.3(Elongation Test)	-	6000	-
Cl-4.4(Proof Stress)	-	6000	-
Cl-4.5.1(Galvanizing)	-	6000	-
Cl-4.5.2(Wrap Test)	-	6000	-
Cl-5(General requirements)	-	0	-
Cl-6(Joints)	-	0	-
Cl-7(Direction of Lay)	-	6000	-
Cl-8(Length of Lay)	-	6000	-
Cl-9(Lubrication)	-	0	-
Cl-10(Minimum Breaking Force)	-	6000	-
Cl-11(Elongation or Stretch of wire rope)	-	6000	-
Cl-12(Marking)	-	0	-
Cl-1 Table 1 to Table 11(Nominal Diameter)	-	12000	-
Cl-1 Table 1 to Table 11(Approximate Mass)	-	12000	-
Cl-1 Table 1 to Table 11(Minimum Breaking Force)	-	12000	-

-
Included w.e.f 01.09.2025

IS 12776 (2002)

Galvanized strand for earthing - Specification (First Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Freedom From Defects (IS 12776))	-	7000	-
5.3(Joints in wires (IS 12776))	-	7000	-
6- Annex-A, Sl-2(Size of the wire (IS 12776))	-	7000	-
6- Annex-A, Sl-8(Lay (IS 12776))	-	7000	-
8.1-Annex-A,Sl-9(Breaking Force of Strand (IS 12776))	-	7000	-
8.2-Annex-A,Sl-6(Elongation of wire, IS 10810(Part-37))	-	7000	-
8.2-Annex-A,Sl-3(Tensile Strength of wire IS 10810(Part-37))	-	7000	-
8.3-Annex-A,Sl-12(Resistance at 200 C (IS 12776))	-	7000	-
8.4(Wrapping Test (IS 12776))	-	7000	-
8.5-Annex-A-Sl-7a(Amount of zinc Coating (IS 6745))	-	7000	-
8.5-Annex-A-Sl-7b(Uniformity of Coating (IS 2633))	-	7000	-
8.5-Annex-A-Sl-4(Torsion Test IS 10810(Part-37))	-	7000	-
4.1(Carbon- IS 228(Part 1))	-	7000	-
4.1(Sulphur- IS 228(Part 9))	-	7000	-
4.1(Phosphorous- IS 228(Part 3))	-	7000	-
4.1(Manganese- IS 228(Part 2))	-	7000	-
4.1(Silicon- IS 228(Part 8))	-	7000	-
6- Annex-A, Sl-8(Lay Length)	-	7000	-

-
Included w.e.f.18.08.2025

IS 17706 (2022)

PULL HANDLES SPECIFICATION

All Types

25000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1(Materials)	-	0	-
Clause 4.2(Fitting Accessories and Installation)	-	0	-
Clause 4.4(Finish)	-	0	-
Clause 5.1(Corrosion Resistance)	-	25000	Grade 1- 5000/-, Grade 2,3 and 4 - 25000/-
Clause 5.2(Durability)	-	25000	Category 1 - 5000/-, Category 2,3, and 4 - 25000/-
Clause 6(Sampling and criteria for conformity)	-	0	-
Clause 7(Marking)	-	0	-
Clause 8(Packing)	-	0	-
Clause 4.1(Materials)	-	0	-
Clause 4.2(Fitting Accessories and Installation)	-	0	-
Clause 4.4(Finish)	-	0	-
Clause 5.1(Corrosion Resistance)	-	0	-
Clause 5.2(Durability)	-	0	-
Clause 6(Sampling and criteria for conformity)	-	0	-
Clause 7(Marking)	-	0	-
Clause 8(Packing)	-	0	-

-
Included w.e.f. 31.12.2025

IS 2047 (1992)

Aluminium alloy hardeners (Master Alloys) - Specification (Second Revision)

All Grade

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General Requirement)	-	12000	-
4(Manufacture )	-	0	-
5.1(Chemical Composition)	-	12000	-
6(Freedom from Defects)	-	12000	-
8(Packing)	-	0	-
9(Marking)	-	0	-

-
Included w.e.f 16.09.2025

IS 15658 (2021)

Concrete Paving Blocks - Specification ( First Revision )

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 50 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 25 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Visual Rating of specimen after 10 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Cumulative Weight losses of specimen after 10, 25 & 50 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 50 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 25 cycles)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (vi)(Freeze Thaw durability (Weight losses of specimen after 10 cycles)	-	0	-
Clause 7.3, Annex G(Average Breaking Load)	-	1000	-
Clause 7.3, Annex G(Individual Breaking Load)	-	1000	-
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	1000	-
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	1000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	3000	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	3000	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	1500	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	1500	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	1500	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	1500	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	1500	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	1500	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	1500	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	1500	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	1500	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	1500	-
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	1000	-
Clause 7.1.1 (General Quality)	-	1000	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	1500	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	1500	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	1500	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	1500	-
Clause 3.20(Spacer nibs)	-	1500	-
5.4(Coarse and Fine Aggregates)	-	0	-
5.6(Water)	-	0	-
Clause 7.3, Annex G(Average Breaking Load)	-	0	-
Clause 7.3, Annex G(Individual Breaking Load)	-	0	-
Clause 7.3, Annex F(Average Failure Load per unit Length)	-	0	-
Clause 7.3, Annex F(Individual Failure Load per unit Length)	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) b)(Average Flexural strength )	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (v) a)(Indivdual Flexural strength (i))	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) b)(Average Tensile splitting strength )	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iv) a)(Indivdual Tensile splitting strength (i))	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) ii)(Wet Abrasion resistance (Average of three test specimens))	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) b) i)( Indivdual Wet Abrasion Resistance )	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) ii)(Dry Abrasion resistance (Average of three test specimens))	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (iii) a) i)( Indivdual Dry Abrasion Resistance )	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) b)(Compressive strength (Average of eight test specimens))	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (ii) a)(Indivdual Compressive strength (i))	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) b)(Water absorption (Average of three test specimens))	-	0	-
Clause 7.3 & 9.1.4, Table 3, SI No. (i) a)( Indivdual Water absorption)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (ix)(Deviation from squareness)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Indivdual Ratio of wearing face area and Plan area (Asw/Asp))	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (viii)(Ratio of wearing face area and Plan area (Asw/Asp))	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Indivdual Plan Area (Asp))	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vii)(Plan Area (Asp))	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Indivdual Thickness of wearing Layer)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (vi)(Thickness of wearing Layer)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Depth)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Depth)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Indivdual Arris/chamfer, Width)	-	0	-
Clause 7.2 & 9.1.3, Table 2, SI No. (v)(Arris/chamfer, Width)	-	0	-
Clause 7.2, Table No. 2, SI No. (iv) (Indivdual Aspect Ratio, L/Th)	-	0	-
Clause 7.2, Table No. 2, SI No. (iv) (Aspect Ratio, L/Th)	-	0	-
Clause 7.2, Table No. 2, SI No. (iii) (Indivdual Thickness, Th)	-	0	-
Clause 7.2, Table No. 2, SI No. (iii) (Thickness, Th)	-	0	-
Clause 7.2, Table No. 2, SI No. (ii) (Indivdual Length, L)	-	0	-
Clause 7.2, Table No. 2, SI No. (ii) (Length, L)	-	0	-
Clause 7.2, Table No. 2, SI No. (i) (Indivdual Width, W)	-	0	-
Clause 7.2, Table No. 2, SI No. (i) (Width, W)	-	0	-
Clauses 7.1.2 & 9.1.2 (Visual Inspection)	-	0	-
Clause 7.1.1 (General Quality)	-	0	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Lower)	-	0	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Lower)	-	0	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Individual Width - Higher)	-	0	-
7.2- TABLE-2- (i) IS-15658 (Annex-B)(Average Width -Higher)	-	0	-
Clause 3.20(Spacer nibs)	-	0	-

-
-

IS 16440 (2016)

Stainless steel milk cans - Specification

All Size as per IS

32500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.2(Carbon)	-	12500	-
5.2(Sulphur)	-	12500	-
5.2(phosphorus)	-	12500	-
5.2(Manganese)	-	12500	-
5.2(Silicon)	-	12500	-
5.2(Chromium)	-	12500	-
5.2(Nickel)	-	12500	-
5.2(molybdenum)	-	12500	-
3.0(Capacity test)	-	10000	-
6.3(Hardness test)	-	10000	-
6.1(Pressure check for leakage and bulging)	-	10000	-
6.2(Drop test)	-	10000	-
6.4(Dye penetration test)	-	10000	-
"As per Clause 4 & Table 1"(Shape & Dimensions)	-	10000	-
As per Clause 5.4(Thickness of parts)	-	10000	-
As per Clause 5.5(Mass of can (Weight))	-	10000	-
As per Clause 5.6(Construction)	-	10000	-
Clause 5.6.1(Body)	-	10000	-
As per Clause 5.6.2(Handle)	-	10000	-
Clause 5.6.3(Bottom ring)	-	10000	-
Clause 5.6.4(Lid)	-	10000	-
Clause 5.6.6(Finish)	-	10000	-
Clause 5.6.7(Heat treatment and Passivation)	-	0	-
Clause 6.5(Leakage test)	-	10000	-
Clause 4 & Table 1"(Shape & Dimensions)	-	10000	-
Clause 5.4(Thickness of parts)	-	10000	-
Clause 5.5(Mass of can (Weight))	-	10000	-
Clause 5.6(Construction)	-	10000	-
Clause 5.6.1(Body)	-	10000	-
Clause 5.6.2(Handle)	-	10000	-
Clause 5.6.3(Bottom ring)	-	10000	-
Clause 5.6.6(Finish)	-	10000	-
Clause 5.6.7(Heat treatment and Passivation)	-	0	-
Clause 6.5(Leakage test)	-	10000	-
5.2(Carbon)	-	0	-
5.2(Sulphur)	-	0	-
5.2(phosphorus)	-	0	-
5.2(Manganese)	-	0	-
5.2(Silicon)	-	0	-
5.2(Chromium)	-	0	-
5.2(Nickel)	-	0	-
5.2(molybdenum)	-	0	-
3.0(Capacity test)	-	0	-
6.3(Hardness test)	-	0	-
6.1(Pressure check for leakage and bulging)	-	0	-
6.2(Drop test)	-	0	-
6.4(Dye penetration test)	-	0	-
"As per Clause 4 & Table 1"(Shape & Dimensions)	-	0	-
As per Clause 5.4(Thickness of parts)	-	0	-
As per Clause 5.5(Mass of can (Weight))	-	0	-
As per Clause 5.6(Construction)	-	0	-
Clause 5.6.1(Body)	-	0	-
As per Clause 5.6.2(Handle)	-	0	-
Clause 5.6.3(Bottom ring)	-	0	-
Clause 5.6.4(Lid)	-	0	-
Clause 5.6.6(Finish)	-	0	-
Clause 5.6.7(Heat treatment and Passivation)	-	0	-
Clause 6.5(Leakage test)	-	0	-
Clause 4 & Table 1"(Shape & Dimensions)	-	0	-
Clause 5.4(Thickness of parts)	-	0	-
Clause 5.5(Mass of can (Weight))	-	0	-
Clause 5.6(Construction)	-	0	-
Clause 5.6.1(Body)	-	0	-
Clause 5.6.2(Handle)	-	0	-
Clause 5.6.3(Bottom ring)	-	0	-
Clause 5.6.6(Finish)	-	0	-
Clause 5.6.7(Heat treatment and Passivation)	-	0	-
Clause 6.5(Leakage test)	-	0	-

-
Included w.e.f 30.01.2026

IS 1254 (2025)

Corrugated Aluminium Sheet (Fifth Revision)

All Size

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-4(FREEDOM FROM DEFECTS)	-	1500	-
Cl-5(SUPPLY OF MATERIALS)	-	0	-
Cl-6(PROFILE)	-	0	-
Cl-7(MATERIAL)	-	0	If raw material is to be tested separate specimen to be sent to lab as per BIS Product Manual. (22500)
Cl-8.1(Tolerance on the thickness)	-	1500	-
Cl-8.2(Width)	-	1500	-
Cl-8.3(Length)	-	1500	-
Cl-8.4(Squareness)	-	2500	-
Cl-8.5(Depth and Pitch of the Corrugation)	-	2500	-
Cl-10(Finish)	-	1500	-
Cl-12(Marking)	-	0	-
Cl-4(FREEDOM FROM DEFECTS)	-	0	-
Cl-5(SUPPLY OF MATERIALS)	-	0	-
Cl-6(PROFILE)	-	0	-
Cl-7(MATERIAL)	-	0	-
Cl-8.1(Tolerance on the thickness)	-	0	-
Cl-8.2(Width)	-	0	-
Cl-8.3(Length)	-	0	-
Cl-8.4(Squareness)	-	0	-
Cl-8.5(Depth and Pitch of the Corrugation)	-	0	-
Cl-10(Finish)	-	0	-
Cl-12(Marking)	-	0	-

-
Included w.e.f 16.09.2025

IS 21 (2025)

Wrought Aluminium and Aluminium Alloys for Manufacture of Utensils - Specification (Fifth Revision)

All Size

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-5.2(Chemical composition and mechanical properties of grades in Cl 5.1)	-	10000	-
Cl-5.3.1 a("Wrought Aluminium (with Minimum 99 Percent Al Content)- Iron+ Silicon")	-	10000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Chromium")	-	10000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Magnesium")	-	10000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Manganese")	-	10000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Nickel")	-	10000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Zinc")	-	10000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Titanium")	-	10000	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Tin")	-	10000	-
Cl-5.3.1 c("Wrought Aluminium (with Minimum 99 Percent Al Content)- Copper")	-	10000	-
Cl-5.3.1 Note 1("Wrought Aluminium (with Minimum 99 Percent Al Content)- Aluminium")	-	10000	-
Cl-5.3.1 d("Wrought Aluminium (with Minimum 99 Percent Al Content)- Others")	-	10000	-
Cl-5.3.2, Table-1 (i)(Wrought Aluminium Alloys-Silicon)	-	10000	-
Cl-5.3.2, Table-1 (ii)(Wrought Aluminium Alloys-Iron)	-	10000	-
Cl-5.3.2, Table-1 (iii)(Wrought Aluminium Alloys-Copper)	-	10000	-
Cl-5.3.2, Table-1 (iv)(Wrought Aluminium Alloys-Manganese)	-	10000	-
Cl-5.3.2, Table-1 (v)(Wrought Aluminium Alloys-Magnesium)	-	10000	-
Cl-5.3.2, Table-1 (vi)(Wrought Aluminium Alloys-Chromium)	-	10000	-
Cl-5.3.2, Table-1 (vii)(Wrought Aluminium Alloys-Nickel)	-	10000	-
Cl-5.3.2, Table-1 (viii)(Wrought Aluminium Alloys-Zinc)	-	10000	-
Cl-5.3.2, Table-1 (ix)(Wrought Aluminium Alloys -Zirconium)	-	10000	-
Cl-5.3.2, Table-1 (x)(Wrought Aluminium Alloys - Titanium)	-	10000	-
Cl-5.3.2, Table-1 (Note 3)(Wrought Aluminium Alloys- Aluminium)	-	10000	-
Cl-5.3.2, Table-1 (xi)(Wrought Aluminium Alloys- Others)	-	10000	-
Cl 5.4(Lead)	-	10000	-
Cl 5.4(Cadmium)	-	10000	-
Cl 5.4(Arsenic)	-	10000	-
Cl-7(Dimension)	-	10000	-
Cl-5.1(Material)	-	10000	-
Cl-4(General requirements)	-	10000	-
Cl-8(EARING TEST (OPTIONAL TEST))	-	0	-
Cl-5.2(Chemical composition and mechanical properties of grades in Cl 5.1)	-	0	-
Cl-5.3.1 a("Wrought Aluminium (with Minimum 99 Percent Al Content)- Iron+ Silicon")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Chromium")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Magnesium")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Manganese")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Nickel")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Zinc")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Titanium")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Tin")	-	0	-
Cl-5.3.1 c("Wrought Aluminium (with Minimum 99 Percent Al Content)- Copper")	-	0	-
Cl-5.3.1 Note 1("Wrought Aluminium (with Minimum 99 Percent Al Content)- Aluminium")	-	0	-
Cl-5.3.1 d("Wrought Aluminium (with Minimum 99 Percent Al Content)- Others")	-	0	-
Cl-5.3.2, Table-1 (i)(Wrought Aluminium Alloys-Silicon)	-	0	-
Cl-5.3.2, Table-1 (ii)(Wrought Aluminium Alloys-Iron)	-	0	-
Cl-5.3.2, Table-1 (iii)(Wrought Aluminium Alloys-Copper)	-	0	-
Cl-5.3.2, Table-1 (iv)(Wrought Aluminium Alloys-Manganese)	-	0	-
Cl-5.3.2, Table-1 (v)(Wrought Aluminium Alloys-Magnesium)	-	0	-
Cl-5.3.2, Table-1 (vi)(Wrought Aluminium Alloys-Chromium)	-	0	-
Cl-5.3.2, Table-1 (vii)(Wrought Aluminium Alloys-Nickel)	-	0	-
Cl-5.3.2, Table-1 (viii)(Wrought Aluminium Alloys-Zinc)	-	0	-
Cl-5.3.2, Table-1 (ix)(Wrought Aluminium Alloys -Zirconium)	-	0	-
Cl-5.3.2, Table-1 (x)(Wrought Aluminium Alloys - Titanium)	-	0	-
Cl-5.3.2, Table-1 (Note 3)(Wrought Aluminium Alloys- Aluminium)	-	0	-
Cl-5.3.2, Table-1 (xi)(Wrought Aluminium Alloys- Others)	-	0	-
Cl 5.4(Lead)	-	0	-
Cl 5.4(Cadmium)	-	0	-
Cl 5.4(Arsenic)	-	0	-
Cl-7(Dimension)	-	0	-
Cl-5.1(Material)	-	0	-
Cl-4(General requirements)	-	0	-
Cl-8(EARING TEST (OPTIONAL TEST))	-	0	-
Cl-5.2(Chemical composition and mechanical properties of grades in Cl 5.1)	-	0	-
Cl-5.3.1 a("Wrought Aluminium (with Minimum 99 Percent Al Content)- Iron+ Silicon")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Chromium")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Magnesium")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Manganese")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Nickel")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Zinc")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Titanium")	-	0	-
Cl-5.3.1 b("Wrought Aluminium (with Minimum 99 Percent Al Content)- Tin")	-	0	-
Cl-5.3.1 c("Wrought Aluminium (with Minimum 99 Percent Al Content)- Copper")	-	0	-
Cl-5.3.1 Note 1("Wrought Aluminium (with Minimum 99 Percent Al Content)- Aluminium")	-	0	-
Cl-5.3.1 d("Wrought Aluminium (with Minimum 99 Percent Al Content)- Others")	-	0	-
Cl-5.3.2, Table-1 (i)(Wrought Aluminium Alloys-Silicon)	-	0	-
Cl-5.3.2, Table-1 (ii)(Wrought Aluminium Alloys-Iron)	-	0	-
Cl-5.3.2, Table-1 (iii)(Wrought Aluminium Alloys-Copper)	-	0	-
Cl-5.3.2, Table-1 (iv)(Wrought Aluminium Alloys-Manganese)	-	0	-
Cl-5.3.2, Table-1 (v)(Wrought Aluminium Alloys-Magnesium)	-	0	-
Cl-5.3.2, Table-1 (vi)(Wrought Aluminium Alloys-Chromium)	-	0	-
Cl-5.3.2, Table-1 (vii)(Wrought Aluminium Alloys-Nickel)	-	0	-
Cl-5.3.2, Table-1 (viii)(Wrought Aluminium Alloys-Zinc)	-	0	-
Cl-5.3.2, Table-1 (ix)(Wrought Aluminium Alloys -Zirconium)	-	0	-
Cl-5.3.2, Table-1 (x)(Wrought Aluminium Alloys - Titanium)	-	0	-
Cl-5.3.2, Table-1 (Note 3)(Wrought Aluminium Alloys- Aluminium)	-	0	-
Cl-5.3.2, Table-1 (xi)(Wrought Aluminium Alloys- Others)	-	0	-
Cl 5.4(Lead)	-	0	-
Cl 5.4(Cadmium)	-	0	-
Cl 5.4(Arsenic)	-	0	-
Cl-7(Dimension)	-	0	-
Cl-5.1(Material)	-	0	-
Cl-4(General requirements)	-	0	-
Cl-8(EARING TEST (OPTIONAL TEST))	-	0	-

-
Included w.e.f 16.09.2025 Excluding: Cl-8 (EARTHING TEST (OPTIONAL TEST))

IS 13352 (1992)

Stock for forgings produced from continuously cast blooms, billets and slabs - Specification

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Freedom from defects)	-	11000	-
6.1, table 2 (2)(C)	-	11000	-
6.1, table 2 (3)(Mn)	-	11000	-
6.1, table 2 (4)(Si)	-	11000	-
6.1, table 2 (5)(Ni)	-	11000	-
6.1, table 2 (6)(Cr)	-	11000	-
6.1, table 2 (7)(Mo)	-	11000	-
6.1, table 2 (8)(V)	-	11000	-
6.1, table 2 (9)(Al)	-	11000	-
6.1, table 3 (1)(Carbon Silicon Manganese Nickel Chromium Molybdenum Vanadium Sulphur Phosphorus)	-	11000	-
7(Mechanical properties)	-	11000	-
8(Grain size)	-	11000	-
9.1(Surface defects)	-	11000	-
9.2(Seams)	-	11000	-
10.1(Inclusion rating of the steel)	-	11000	-
10.2(Step down test & magnetic particle test)	-	11000	-
11(Hardenability)	-	11000	-
12(Dimensions and Tolerances)	-	11000	-
14(Retest)	-	22000	-
5(Freedom from defects)	-	0	-
6.1, table 2 (2)(C)	-	0	-
6.1, table 2 (3)(Mn)	-	0	-
6.1, table 2 (4)(Si)	-	0	-
6.1, table 2 (5)(Ni)	-	0	-
6.1, table 2 (6)(Cr)	-	0	-
6.1, table 2 (7)(Mo)	-	0	-
6.1, table 2 (8)(V)	-	0	-
6.1, table 2 (9)(Al)	-	0	-
6.1, table 3 (1)(Carbon Silicon Manganese Nickel Chromium Molybdenum Vanadium Sulphur Phosphorus)	-	0	-
7(Mechanical properties)	-	0	-
8(Grain size)	-	0	-
9.1(Surface defects)	-	0	-
9.2(Seams)	-	0	-
10.1(Inclusion rating of the steel)	-	0	-
10.2(Step down test & magnetic particle test)	-	0	-
11(Hardenability)	-	0	-
12(Dimensions and Tolerances)	-	0	-
14(Retest)	-	0	-

-
Included w.e.f 22.09.2025

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

All thickness

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(UTM)	-	5000	-
Cl 9(Press)	-	5000	-
Cl 10(Die Press)	-	5000	-
Cl 12(Workmanship)	-	5000	-
Cl 13(Length, Width & Thickness)	-	5000	-
Cl 8(UTM)	-	5000	-
Cl 9(Press)	-	5000	-
Cl 10(Die Press)	-	5000	-
Cl 8(UTM)	-	5000	-
Cl 9(Press)	-	5000	-
Cl 10(Die Press)	-	5000	-
Cl 12(Workmanship)	-	5000	-
Cl 13(Length, Width & Thickness)	-	5000	-
6.1(Carbon %)	-	4000	-
6.1(Manganese %)	-	4000	-
6.1(Phosphorus %)	-	4000	-
6.1(Sulphur %)	-	4000	-
6.1(Silicon %)	-	4000	-
6.1( Copper %)	-	4000	-
6.1( Aluminium %)	-	4000	-
6.1( Nb)	-	4000	-
6.1(V)	-	4000	-
6.1( Ti)	-	4000	-
6.1(Cr)	-	4000	-
6.1(Mo)	-	4000	-
6.1(Ni)	-	4000	-
6.1( Nitrogen%)	-	4000	-
6.1(Microalloying)	-	4000	-
6.1(Carbon %)	-	4000	-
6.1(Manganese %)	-	4000	-
6.1(Phosphorus %)	-	4000	-
6.1(Sulphur %)	-	4000	-
6.1(Silicon %)	-	4000	-
6.1( Copper %)	-	4000	-
6.1( Aluminium %)	-	4000	-
6.1( Nb)	-	4000	-
6.1(V)	-	4000	-
6.1( Ti)	-	4000	-
6.1(Cr)	-	4000	-
6.1(Mo)	-	4000	-
6.1(Ni)	-	4000	-
6.1( Nitrogen%)	-	4000	-
6.1(Microalloying)	-	4000	-
Cl 12(Workmanship)	-	5000	-
Cl 13(Length, Width & Thickness)	-	5000	-
6.1(Carbon %)	-	4000	-
6.1(Manganese %)	-	4000	-
6.1(Phosphorus %)	-	4000	-
6.1(Sulphur %)	-	4000	-
6.1(Silicon %)	-	4000	-
6.1( Copper %)	-	4000	-
6.1( Aluminium %)	-	4000	-
6.1( Nb)	-	4000	-
6.1(V)	-	4000	-
6.1( Ti)	-	4000	-
6.1(Cr)	-	4000	-
6.1(Mo)	-	4000	-
6.1(Ni)	-	4000	-
6.1( Nitrogen%)	-	4000	-
6.1(Microalloying)	-	4000	-
Cl.13(Out of square)	-	5000	-
Cl.13(Flatness)	-	5000	-
Cl.13(Camber)	-	5000	-
Cl.13(Width)	-	5000	-
Cl.13(Thickness)	-	5000	-
Cl. 8.3, Cl. 8.3.1 Table 5 and Table 6(Percentage Elongation After Fracture at 5.65√A Gauge length)	-	5000	-
Cl. 8.3, Cl. 8.3.1 Table 5 and Table 6(Percentage Elongation After Fracture at 80 mm Gauge length)	-	5000	-
Cl. 8.3, Cl. 8.3.1 Table 5 and Table 6(Percentage Elongation After Fracture at 50 mm Gauge length)	-	5000	-
Cl. 8.3, Cl. 8.3.1 Table 6(0.2% Proof Stress/Yield Stress)	-	5000	-
Cl 13(Length, Width & Thickness)	-	5000	-
Cl 12(Workmanship)	-	5000	-
Cl 9(Press)	-	5000	-
Cl 8(UTM)	-	5000	-
7(Material Test)	-	4000	-
9(Bend test)	-	5000	-
14(Calculation of weight)	-	5000	-
Cl 8(UTM)	-	5000	-
Cl 9(Press)	-	5000	-
Cl 12(Workmanship)	-	5000	-
Cl 13(Length, Width & Thickness)	-	5000	-
8, Table 5 & 6(Tensile Strength)	-	5000	-
8, Table 5 & 6(Yield Strength)	-	5000	-
8, Table 5 & 6(Elongation)	-	5000	-
Clause 10(Cuppping Test)	-	5000	-
Clause 12(Freedom from defect)	-	5000	-
Clause 13(Length)	-	5000	-
Clause 7, Table 3, Note 1(Any Instrumental Method/Chemical Method)	-	4000	-
Clause 7, Table 3, Note 1(By Calculation)	-	4000	-
8, Table 5 & 6(Tensile Strength)	-	5000	-
8, Table 5 & 6(Yield Strength)	-	5000	-
8, Table 5 & 6(Elongation)	-	5000	-
Clause 10(Cuppping Test)	-	5000	-
Clause 12(Freedom from defect)	-	5000	-
Clause 13(Length)	-	5000	-
Clause 7, Table 3, Note 1(Boron)	-	4000	-
Clause 7, Table 3, Note 1(B+Ti+Nb+V)	-	4000	-
8, Table 5 & 6(IS 1608 Part 1)	-	5000	-
8, Table 5 & 6(IS 1608 Part 1)	-	5000	-
8, Table 5 & 6(IS 1608 Part 1)	-	5000	-
Clause 10(IS 10175)	-	5000	-
Clause 12(IS 1079)	-	5000	-
Clause 13(IS/ISO 16160)	-	5000	-
Clause 7, Table 3, Note 1(Boron)	-	4000	-
Clause 7, Table 3, Note 1(B+Ti+Nb+V)	-	5000	-
Cl 10(Die Press)	-	5000	-
Cl 10(Die Press)	-	5000	-

-
Included w.e.f 28.07.2025

IS 1875 (1992)

Carbon steel billets, blooms, slabs and bars for forgings - Specification (Fifth Revision)

Bars, Billets, Blooms, and slabs of all size

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Workmanship)	-	5000	-
Cl 8(Diameter, Ovality & Weight)	-	5000	-
Cl 9(UTM & HBW)	-	5000	-
Cl 7(Workmanship)	-	5000	-
Cl 8(Diameter, Ovality & Weight)	-	5000	-
Cl 9(UTM & HBW)	-	5000	-
Cl 7(Workmanship)	-	5000	-
Cl 8(Diameter, Ovality & Weight)	-	5000	-
Cl 9(UTM & HBW)	-	5000	-
6.1, 6.2(cr + n + mo)	-	4000	-
6.1, 6.2(tin)	-	4000	-
6.1, 6.2(boron)	-	4000	-
6.1, 6.2(vanadium)	-	4000	-
6.1, 6.2(molybdenum)	-	4000	-
6.1, 6.2(copper)	-	4000	-
6.1, 6.2(cromium)	-	4000	-
6.1, 6.2(nickel)	-	4000	-
6.1, 6.2(aluminium)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6.1, 6.2(phosphorus)	-	4000	-
6.1, 6.2(sulphur)	-	4000	-
6.1, 6.2(manganese)	-	4000	-
6.1, 6.2(silicon )	-	4000	-
6.1, 6.2(carbon)	-	4000	-
6, table 1(Chemical Composition)	-	4000	-
7(Freedom from defects)	-	5000	-
8(Dimensional Properties (Diameter))	-	5000	-
8(Dimensional Properties (Ovality))	-	5000	-
8(Dimensional Properties (Weight per Meter, kg))	-	5000	-
9.1, table 2(Tensile Strength)	-	5000	-
9.1, table 2(Yield Strength)	-	5000	-
9.1, table 2(Elongation)	-	5000	-
9.2, table 2(hardness test)	-	5000	-
12.2(Bend Test)	-	5000	-
12.3(grain size)	-	5000	-
12.4(Macrostructure)	-	5000	-
12.7(Blue Fracture Test)	-	5000	-
Cl 9(UTM & HBW)	-	5000	-
Cl 8(Diameter, Ovality & Weight)	-	5000	-
Cl 7(Workmanship)	-	5000	-
Cl 7(Workmanship)	-	5000	-
Cl 8(Diameter, Ovality & Weight)	-	5000	-
Cl 9(UTM & HBW)	-	5000	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	5000	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	5000	-
9.1(Tensile Strength - IS: 1608(P1))	-	5000	-
9.1(Yield Strength-IS:1608(P1))	-	5000	-
9.1(Elongation on SoA 5.65mm GL)	-	5000	-
9.2(Hardness-HB IS:1500 (P1))	-	5000	-
12.0 & 12.2(Bend Test - IS 1599)	-	5000	-
12.0 & 12.3(Grain Size - IS 4748)	-	5000	-
12.0 & 12.4(Macrostructure- IS 11371)	-	5000	-
7(Freedom from defects)	-	5000	-
12.7(Blue fracture test (IS:1875-1985))	-	5000	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	4000	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	4000	-
Cl-8(Diameter.)	-	5000	-
Cl-8(Ovality)	-	5000	-
Cl 7(Workmanship)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 9(UTM & HBW)	-	0	-
Cl 7(Workmanship)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 9(UTM & HBW)	-	0	-
Cl 7(Workmanship)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 9(UTM & HBW)	-	0	-
6, table 1(Chemical Composition)	-	0	-
7(Freedom from defects)	-	0	-
8(Dimensional Properties (Diameter))	-	0	-
8(Dimensional Properties (Ovality))	-	0	-
8(Dimensional Properties (Weight per Meter, kg))	-	0	-
9.1, table 2(Tensile Strength)	-	0	-
9.1, table 2(Yield Strength)	-	0	-
9.1, table 2(Elongation)	-	0	-
9.2, table 2(hardness test)	-	0	-
12.2(Bend Test)	-	0	-
12.3(grain size)	-	0	-
12.4(Macrostructure)	-	0	-
12.7(Blue Fracture Test)	-	0	-
Cl 9(UTM & HBW)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 7(Workmanship)	-	0	-
Cl 7(Workmanship)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 9(UTM & HBW)	-	0	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	0	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	0	-
9.1(Tensile Strength - IS: 1608(P1))	-	0	-
9.1(Yield Strength-IS:1608(P1))	-	0	-
9.1(Elongation on SoA 5.65mm GL)	-	0	-
9.2(Hardness-HB IS:1500 (P1))	-	0	-
12.0 & 12.2(Bend Test - IS 1599)	-	0	-
12.0 & 12.3(Grain Size - IS 4748)	-	0	-
12.0 & 12.4(Macrostructure- IS 11371)	-	0	-
7(Freedom from defects)	-	0	-
12.7(Blue fracture test (IS:1875-1985))	-	0	-
Clause 6, Table 1, Note 1(Cr+Ni+Mo)	-	0	-
Clause 6, Table 1, Note 2(Cu +(10xTin))	-	0	-
Cl-8(Diameter.)	-	0	-
Cl-8(Ovality)	-	0	-
Cl 12(Supplementary Requirements)	-	0	-
Cl 12(Supplementary Requirements)	-	0	-
Cl 12(Supplementary Requirements)	-	0	-
Cl 12(Supplementary Requirements)	-	0	-
Cl 12(Supplementary Requirements)	-	0	-

-
Included w.e.f.18.08.2025 Exclusion Cl "12.5 (Ultrasonic Test)12.6 (Magnetic Particle Test) Cl 12.0 & 12.5 (Ultrasnoic Test) Cl 12.0 & 12.6 (Magnetic Particle Test - IS 10138 (P3))

IS 18809 (2024)

Wear and abrasion resistant steel sheet and plate ï¿½ Specification

Plate and Sheet

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
2(References)	-	0	-
3(Supply of Material)	-	0	-
3.1(Supply of Material)	-	0	-
3.2(Supply of Material)	-	0	-
3.3(Supply of Material)	-	0	-
4(Terminology)	-	0	-
4.1(Quenching)	-	0	-
4.2(Tempering)	-	0	-
4.3(Wear and Abrasion Resistant Steel)	-	0	-
4.4(Product)	-	0	-
5(Classification and Designation)	-	0	-
5.1(Designation)	-	0	-
5.2 (Table 1)(Grades (Hardness) HBW)	-	0	-
6(Manufacture)	-	0	-
6.1(Manufacture)	-	0	-
6.2(Manufacture)	-	0	-
7.1 (Table 2)(Chemical Compostion ( C))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( Mn))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( Si))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( P))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( S))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( Cr))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( Mo))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( Ni))	-	7000	-
7.1 (Table 2)(Chemical Compostion ( B))	-	7000	-
7.1 (Table 3)(Chemical Compostion ( Carbon Equivalent))	-	7000	-
7.1 (Table 3)(Chemical Compostion ( Al))	-	7000	-
7.1 (Table 3)(Chemical Compostion ( Nb))	-	7000	-
7.1 (Table 3)(Chemical Compostion ( V))	-	7000	-
7.1 (Table 3)(Chemical Compostion (Ti))	-	7000	-
7.1 (Table 3)(Chemical Compostion ( N))	-	7000	-
8 (Table -6)(Mechanical Properties ( Yield Strength )Mpa)	-	7000	-
8 (Table -6)(Mechanical Properties ( Tensile Strength )Mpa)	-	7000	-
8 (Table -6)(Mechanical Properties ( Elongation )%)	-	7000	-
8 (Table -7)(Bend Radius (Bend Angle:90 deg.))	-	7000	-
8 (Table 8)(Charpy Impact Value)	-	7000	-
8.1 (Table-5)(Hardness Test)	-	7000	-
8.2(Tensile test)	-	7000	-
8.3 (Table 7)(Bend Test)	-	7000	-
8.4 (Table 8)(Charpy V-Notch- Impact Test)	-	7000	-
9(Non Destrictive Test)	-	0	-
10(Retest)	-	14000	-
11(Freedom From Defects)	-	7000	-
12(Dimenstions and Tolerences)	-	7000	-
13(Marking)	-	0	-
14(Delivery)	-	0	-
15(BIS Certification Marking)	-	0	-
16(Ordering Information)	-	0	-
Cl.7(Carbon - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Silicon - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Phosphorus - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Sulphur - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Molybdenum - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Nickel - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Nitrogen - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
2(References)	-	0	-
3(Supply of Material)	-	0	-
3.1(Supply of Material)	-	0	-
3.2(Supply of Material)	-	0	-
3.3(Supply of Material)	-	0	-
4(Terminology)	-	0	-
4.1(Quenching)	-	0	-
4.2(Tempering)	-	0	-
4.3(Wear and Abrasion Resistant Steel)	-	0	-
4.4(Product)	-	0	-
5(Classification and Designation)	-	0	-
5.1(Designation)	-	0	-
5.2 (Table 1)(Grades (Hardness) HBW)	-	0	-
6(Manufacture)	-	0	-
6.1(Manufacture)	-	0	-
6.2(Manufacture)	-	0	-
7.1 (Table 2)(Chemical Compostion ( C))	-	0	-
7.1 (Table 2)(Chemical Compostion ( Mn))	-	0	-
7.1 (Table 2)(Chemical Compostion ( Si))	-	0	-
7.1 (Table 2)(Chemical Compostion ( P))	-	0	-
7.1 (Table 2)(Chemical Compostion ( S))	-	0	-
7.1 (Table 2)(Chemical Compostion ( Cr))	-	0	-
7.1 (Table 2)(Chemical Compostion ( Mo))	-	0	-
7.1 (Table 2)(Chemical Compostion ( Ni))	-	0	-
7.1 (Table 2)(Chemical Compostion ( B))	-	0	-
7.1 (Table 3)(Chemical Compostion ( Carbon Equivalent))	-	0	-
7.1 (Table 3)(Chemical Compostion ( Al))	-	0	-
7.1 (Table 3)(Chemical Compostion ( Nb))	-	0	-
7.1 (Table 3)(Chemical Compostion ( V))	-	0	-
7.1 (Table 3)(Chemical Compostion (Ti))	-	0	-
7.1 (Table 3)(Chemical Compostion ( N))	-	0	-
8 (Table -6)(Mechanical Properties ( Yield Strength )Mpa)	-	0	-
8 (Table -6)(Mechanical Properties ( Tensile Strength )Mpa)	-	0	-
8 (Table -6)(Mechanical Properties ( Elongation )%)	-	0	-
8 (Table -7)(Bend Radius (Bend Angle:90 deg.))	-	0	-
8 (Table 8)(Charpy Impact Value)	-	0	-
8.1 (Table-5)(Hardness Test)	-	0	-
8.2(Tensile test)	-	0	-
8.3 (Table 7)(Bend Test)	-	0	-
8.4 (Table 8)(Charpy V-Notch- Impact Test)	-	0	-
9(Non Destrictive Test)	-	0	-
10(Retest)	-	0	-
11(Freedom From Defects)	-	0	-
12(Dimenstions and Tolerences)	-	0	-
13(Marking)	-	0	-
14(Delivery)	-	0	-
15(BIS Certification Marking)	-	0	-
16(Ordering Information)	-	0	-
Cl.7(Carbon - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Manganese - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Silicon - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Phosphorus - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Sulphur - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Chromium - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Molybdenum - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Nickel - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-
Cl.7(Nitrogen - IS 228 and its parts or any other intrumental/chemical methods)	-	0	-

-
Included w.e.f.04.08.2025

IS 2385 (1977)

Specification for hot - Rolled mild steel sheet and strip in coil form for cold - Reduced tinplate and cold - Reduced blackplate (First Revision)

All Size

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1, 5.2 & Table1(Carbon- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	7000	-
Cl. 5.1, 5.2 & Table1(Manganese- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	7000	-
Cl. 5.1, 5.2 & Table1(Sulphur- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	7000	-
Cl. 5.1, 5.2 & Table1(Phosphorus- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	7000	-
Cl. 5.1, 5.2 & Table1(Nitrogen- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	7000	-
Cl. 5.1, 5.2 & Table1(Aluminium- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	7000	-
6(Freedom from defects)	-	5000	-
8(Dimensions and Tolerances)	-	5000	-
Cl. 5.1, 5.2(chromium)	-	7000	-
Cl. 5.1, 5.2(silicon)	-	7000	-
Cl. 5.1, 5.2(copper)	-	7000	-
Cl. 5.1, 5.2(aluminium)	-	7000	-
Cl. 5.1, 5.2(Nitrogen )	-	7000	-
Cl. 5.1, 5.2(Phosphorus)	-	7000	-
Cl. 5.1, 5.2(Sulphur)	-	7000	-
Cl. 5.1, 5.2(Manganese)	-	7000	-
Cl. 5.1, 5.2(carbon)	-	7000	-
Cl. 5.1, 5.2 & Table1(Carbon- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5.1, 5.2 & Table1(Manganese- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5.1, 5.2 & Table1(Sulphur- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5.1, 5.2 & Table1(Phosphorus- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5.1, 5.2 & Table1(Nitrogen- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	0	-
Cl. 5.1, 5.2 & Table1(Aluminium- Appropriate parts of IS 228 or any other established Instrumental/Chemical method.)	-	0	-
6(Freedom from defects)	-	0	-
8(Dimensions and Tolerances)	-	0	-
Cl. 5.1, 5.2(chromium)	-	0	-
Cl. 5.1, 5.2(silicon)	-	0	-
Cl. 5.1, 5.2(copper)	-	0	-
Cl. 5.1, 5.2(aluminium)	-	0	-
Cl. 5.1, 5.2(Nitrogen )	-	0	-
Cl. 5.1, 5.2(Phosphorus)	-	0	-
Cl. 5.1, 5.2(Sulphur)	-	0	-
Cl. 5.1, 5.2(Manganese)	-	0	-
Cl. 5.1, 5.2(carbon)	-	0	-

-
Included w.e.f 22.07.2025

IS 17876 (2022)

Stainless steel welded pipes and tubes for general service

All Size

22000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	10000	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	12000	-
11(Transverse Tension Test,%)	-	12000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	12000	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	12000	-
14(Reverse Flattaning Test)	-	12000	-
15(Flattaning Test-IS 2328)	-	12000	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	12000	-
18(Leak Tighteness Test)	-	12000	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	12000	-
22(Workmanship, Finish and Appearance)	-	12000	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	12000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	10000	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	10000	-
Clause 10.1 - Table 4(Tensile Strength)	-	12000	-
Clause 10.1 - Table 4(Yield Strength)	-	12000	-
Clause 10.1 - Table 4(Percent Elongation)	-	12000	-
Clause 11(Transverse Tension Test)	-	12000	-
Clause 12(Hardness Test)	-	12000	-
Clause 13(Flange Test)	-	12000	-
Clause 14(Reverse Flattening Test)	-	12000	-
Clause 15(Flattening Test)	-	12000	-
Clause 16(Grain Size)	-	12000	-
Clause 18()	-	12000	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	12000	-
Clause 22(Workmanship, Finish & Appearance)	-	12000	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	10000	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	10000	-
8.1 & 8.2 (Table No.- 1)(Tungstun (W))	-	10000	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	10000	-
12.2(Hardness test)	-	12000	-
6.7, Table 7, ii)(c) Chromium VI)	-	10000	-
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	0	-
10.1 (Table No.- 4)(Tensile Test,Mpa)	-	0	-
11(Transverse Tension Test,%)	-	0	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	0	-
13 (Table No.- 7)(Flange Test-IS 2330)	-	0	-
14(Reverse Flattaning Test)	-	0	-
15(Flattaning Test-IS 2328)	-	0	-
16 (Table No.- 8)(Grain Size,No.-IS 4748)	-	0	-
18(Leak Tighteness Test)	-	0	-
19("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	0	-
22(Workmanship, Finish and Appearance)	-	0	-
24 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	0	-
"Clause 19 IS 10461(Part 1)"(Corrosion Test)	-	0	-
Clause 10.1 - Table 4(Tensile Strength)	-	0	-
Clause 10.1 - Table 4(Yield Strength)	-	0	-
Clause 10.1 - Table 4(Percent Elongation)	-	0	-
Clause 11(Transverse Tension Test)	-	0	-
Clause 12(Hardness Test)	-	0	-
Clause 13(Flange Test)	-	0	-
Clause 14(Reverse Flattening Test)	-	0	-
Clause 15(Flattening Test)	-	0	-
Clause 16(Grain Size)	-	0	-
Clause 18()	-	0	-
"Clause 19 IS 10461(Part 2)"(Corrosion Test)	-	0	-
Clause 22(Workmanship, Finish & Appearance)	-	0	-
Clause 24 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	0	-
8.1 & 8.2 (Table No.- 1)(Vanadium (V))	-	0	-
8.1 & 8.2 (Table No.- 1)(Tungstun (W))	-	0	-
8.1 & 8.2 (Table No.- 1)(Tantalum (Ta))	-	0	-
12.2(Hardness test)	-	0	-
6.7, Table 7, ii)(c) Chromium VI)	-	0	-

-
Included w.e.f 16.07.2025 Exclusion: Eddy Current

IS 17875 (2022)

Stainless Steel seamless pipes and tubes for general service

All Size

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	10000	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	10000	-
11(Transverse Tension Test,%)	-	10000	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	10000	-
13 (Table No.- 7)(Flaring Test)	-	10000	-
14(Flattaning Test-IS 2328)	-	10000	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	10000	-
17(Leak Tighteness Test)	-	10000	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	10000	-
21(Workmanship, Finish and Appearance)	-	10000	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	10000	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	10000	-
Clause 10.1 - Table 4(Tensile Strength)	-	10000	-
Clause 10.1 - Table 4(Percent Elongation)	-	10000	-
Clause 11(Transverse Tension Test)	-	10000	-
Clause 12(Hardness Test)	-	10000	-
Clause 13(Flaring Test)	-	10000	-
Clause 14(Flattening Test)	-	10000	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	10000	-
10.2(Hardness test IS 1500 (part-1):2019)	-	10000	-
12.2(Flaring test IS 17878:2022)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	10000	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	10000	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	10000	-
Clause 15(Grain Size)	-	10000	-
Clause 17(Leak Tightness Test)	-	10000	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	10000	-
Clause 21(Workmanship, Finish & Appearance)	-	10000	-
8.0 (Table No.- 1)(Chemical Composition,% - IS 228)	-	0	-
10.1 (Table No.- 4)(Tensile Test,Mpa - IS 1608)	-	0	-
11(Transverse Tension Test,%)	-	0	-
12 (Table No.- 5)(Hardness Test,HRC,HRB&BHN- IS 1500 (Part 1) or IS 1586 (Part 1))	-	0	-
13 (Table No.- 7)(Flaring Test)	-	0	-
14(Flattaning Test-IS 2328)	-	0	-
15.1 (Table No.- 8)(Grain Size,No.-IS 4748)	-	0	-
17(Leak Tighteness Test)	-	0	-
18("Corrosion Test-IS 10461 (Part 1) or IS 10461 (Part 2)")	-	0	-
21(Workmanship, Finish and Appearance)	-	0	-
23 (Table No.- 9,10&11)(Dimensions and Tolerances,mm)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Carbon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Silicon)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Mangnese)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nickel)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Chromium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Molybdenum)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Sulphur)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Phosphorous)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Nitrogen)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Copper)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Aluminium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Titanium)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Niobium)	-	0	-
"Clause 18 IS 10461(Part 1)"(Corrosion Test)	-	0	-
Clause 10.1 - Table 4(Tensile Strength)	-	0	-
Clause 10.1 - Table 4(Percent Elongation)	-	0	-
Clause 11(Transverse Tension Test)	-	0	-
Clause 12(Hardness Test)	-	0	-
Clause 13(Flaring Test)	-	0	-
Clause 14(Flattening Test)	-	0	-
Clause 23 Annexure A, Table 9 Table 10(Dimensions & Tolerances)	-	0	-
10.2(Hardness test IS 1500 (part-1):2019)	-	0	-
12.2(Flaring test IS 17878:2022)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(W)	-	0	-
"Clause 8.1 and 8.2 - Table 1"(Ta)	-	0	-
"Clause 8.1 and 8.2 - Table 2"(V)	-	0	-
Clause 15(Grain Size)	-	0	-
Clause 17(Leak Tightness Test)	-	0	-
"Clause 18 IS 10461(Part 2)"(Corrosion Test)	-	0	-
Clause 21(Workmanship, Finish & Appearance)	-	0	-

-
Included w.e.f 16.07.2025 Exclusion: Eddy Current

IS 11890 (1987)

Specification for high purity primary aluminium ingots for remelting for special applications

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. No.3(SUPPLY OF YATERIAL)	-	2500	-
Cl. No.5(GRADES)	-	2000	-
Cl. No.6.1,Table no. 1(i)(Aluminium,)	-	500	-
Cl. No.6.1,Table no. 1(ii)(Copper)	-	500	-
Cl. No.6.1,Table no. 1(iii)(Silicon)	-	500	-
Cl. No.6.1,Table no. 1(iv)(Iron)	-	500	-
Cl. No.6.1,Table no. 1(v)(Manganese)	-	500	-
Cl. No.6.1,Table no. 1(vi)(Magnesium)	-	500	-
Cl. No.6.1,Table no. 1(vii)(Zinc)	-	500	-
Cl. No.6.1,Table no. 1(viii)(Titanium + Vanadium)	-	500	-
Cl. No.6.1,Table no. 1(ix)(Gallium)	-	500	-
Cl. No.6.1,Table no. 1(x)(Other elements)	-	500	-
Cl. No.7(SHAPES AND SIZES)	-	1000	-
Cl. No.8(SELECTION OF SAMPLES FOR ANALYSIS)	-	500	-

-
Included w.e.f 28.07.2025

IS 4171 (1983)

Specification for copper rods and bars for general engineering purposes (First Revision)

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 4.1 Table 1(1. Copper, including silver, min)	-	500	-
Clause 4.1 Table 1(2. Tin, max)	-	1000	-
Clause 4.1 Table 1(3. Lead, max)	-	1000	-
Clause 4.1 Table 1(5. Nickel, max)	-	1000	-
Clause 4.1 Table 1(6. Arsenic, max)	-	1000	-
Clause 4.1 Table 1(7. Antimony, max)	-	1000	-
Clause 4.1 Table 1(8. Bismuth, max)	-	1000	-
Clause 4.1 Table 1(9. Phosphorus)	-	1000	-
Clause 4.1 Table 1(10. Selenium and Tellurium, max)	-	1000	-
Clause 4.1 Table 1(11. Total impurities ( excluding silver, nickel and phosphorus ), max)	-	1000	-
5.2(Hydrogen Embrittlement test)	-	1000	-
5.1(Tensile Properties)	-	2500	-
7.1(Dimension and Tolerances)	-	1000	-

-
Included w.e.f 28.07.2025

IS 6754 (1972)

Specification for aluminium alloy ingots for bearings

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1(Chemical composition)	-	500	-
5.1(Shape and size)	-	500	-
6(Freedom from Defects)	-	500	-
7(Selection of Sample for chemical analysis)	-	500	-
8(Retest)	-	1500	-
Table-1, Clause - 4.1(Copper)	-	500	-
Table-1, Clause - 4.1(Magnesium)	-	500	-
Table-1, Clause - 4.1(Manganese)	-	500	-
Table-1, Clause - 4.1(Titanium)	-	500	-
Table-1, Clause - 4.1(Silicon)	-	500	-
Table-1, Clause - 4.1(Nickel)	-	500	-
Table-1, Clause - 4.1(Tin)	-	500	-
Table-1, Clause - 4.1(Other elements)	-	500	-
Table-1, Clause - 4.1(Total of Fe+Si+Mn)	-	500	-
Table-1, Clause - 4.1(Aluminium)	-	500	-

-
Included w.e.f 28.07.2025

IS 14810 (2000)

Copper tubes for plumbing - Specification

14500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 6("Freedom from defects")	-	1000	-
Clause 7(Chemical composition)	-	1200	-
Clause 10("DIMENSIONS AND TOLERANCES")	-	800	-
Clause 11.1(Tensile Test)	-	2000	-
Clause 11.2(Drift Expanding Test)	-	1000	-

-
Included w.e.f 28.07.2025 Exclusion: Clause 12 (HYDROSTATIC TEST)

First
Prev
2
3
4
5
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Gravitas Laboratories Private Limited, Greater Noida

Plot No. 95, Udyog Vihar Extn, Ecotech II, Surajpur I.A., Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201306

7042049001 testinggravitas@gmail.com

Scope List