BIS - LIMS (Laboratory Information Management System)

Gravitas Laboratories Private Limited, Greater Noida

Plot No. 95, Udyog Vihar Extn, Ecotech II, Surajpur I.A., Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201306

7042049001 testinggravitas@gmail.com

Scope List

Reset

155 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

All size

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
6 AND AS PER IS 7887(MICRO ALLOY)	-	500	-
6 AND AS PER IS 7887(ALUMINIUM)	-	500	-
6 AND AS PER IS 7887(PHOSPHORUS)	-	500	-
6 AND AS PER IS 7887(SULPHUR)	-	500	-
6 AND AS PER IS 7887(MANGANESE)	-	500	-
6 AND AS PER IS 7887(SILICON)	-	500	-
6 AND AS PER IS 7887(CARBON)	-	500	-
7 & 8(Ovality)	-	500	-
7 & 8(Diameter)	-	500	-
9.2(Wrapping Test)	-	1500	-
9.3(Bend test)	-	1000	-
10(Finish)	-	500	-
11(Coating test)	-	800	-
13(Freedom from defects)	-	800	-
Cl 13(Workmanship)	-	800	-
Cl 11(Workmanship)	-	800	-
Cl 9(Tensile Test On UTM)	-	800	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	880	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	-
Cl 9(Tensile Test On UTM)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 13(Workmanship)	-	500	-
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	500	-
Clause 6 and Note 3 of IS 7887(Copper)	-	500	-
Clause 6 and Note 3 of IS 7887(Copper)	-	500	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
9.3(Bend test)	-	0	-
10(Finish)	-	0	-
11(Coating test)	-	0	-
13(Freedom from defects)	-	0	-
Cl 13(Workmanship)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 9(Tensile Test On UTM)	-	0	-
Cl 11(Workmanship)	-	0	-
Cl 13(Workmanship)	-	0	-
Clause 6 and Note 3 of IS 7887(Any Instrumental Method/Chemical Method)	-	0	-
Clause 6 and Note 3 of IS 7887(Copper)	-	0	-
Clause 6 and Note 3 of IS 7887(Copper)	-	0	-

-
Included w.e.f 22.07.2025

IS 11169 : Part 2 (2023)

STEELS FOR COLD HEADING/COLD EXTRUSION APPLICATIONS part 2 stainless steels-SPECIFICATION (first revision)

All size

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7.1(Ladle Analysis)	-	500	-
Cl-7.2, Table-1 (i)(Carbon)	-	500	-
Cl-7.2, Table-1 (ii)(Silicon)	-	500	-
Cl-7.2, Table-1 (iii)(Manganese)	-	500	-
Cl-7.2, Table-1 (iv)(Chromium)	-	500	-
Cl-7.2, Table-1 (v)(Molybdenum)	-	500	-
Cl-7.2, Table-1 (vi)(Nickel)	-	500	-
Cl-7.2, Table-1 (vii)(Sulphur)	-	500	-
Cl-7.2, Table-1 (viii)(Phosphorus)	-	500	-
Cl-7.2, Table-1 (ix)(Titanium)	-	500	-
Cl-7.2, Table-1 (x)(Nitrogen)	-	500	-
Cl-7.2, Table-1 (xi)(Aluminium)	-	500	-
Cl-7.2, Table-1 (xii)(Boron)	-	500	-
Cl-7.2, Table-1 (xiii)(Copper)	-	500	-
Cl-7.2, Table-1 (xiv)(Vanadium)	-	500	-
Cl-8.1,(Mechanical properties)	-	500	-
Cl-10.1(Upsetting Test)	-	500	-
Cl-12(Retests)	-	2000	-
Cl-13.2.1(Tolerances on Bright Bars)	-	500	-
Cl-13.2.1.1(Tolerance Classes)	-	500	-
Cl-13.2.1.1(Width Tolerance for Drawn Flats)	-	500	-
Cl-13.2.3(Straightness Tolerance)	-	500	-
Cl-13.2.4(Out of Shape)	-	500	-
Cl-13.2.5(Edges of Non-Round Bars)	-	500	-
Cl-7.1(Ladle Analysis)	-	0	-
Cl-7.2, Table-1 (i)(Carbon)	-	0	-
Cl-7.2, Table-1 (ii)(Silicon)	-	0	-
Cl-7.2, Table-1 (iii)(Manganese)	-	0	-
Cl-7.2, Table-1 (iv)(Chromium)	-	0	-
Cl-7.2, Table-1 (v)(Molybdenum)	-	0	-
Cl-7.2, Table-1 (vi)(Nickel)	-	0	-
Cl-7.2, Table-1 (vii)(Sulphur)	-	0	-
Cl-7.2, Table-1 (viii)(Phosphorus)	-	0	-
Cl-7.2, Table-1 (ix)(Titanium)	-	0	-
Cl-7.2, Table-1 (x)(Nitrogen)	-	0	-
Cl-7.2, Table-1 (xi)(Aluminium)	-	0	-
Cl-7.2, Table-1 (xii)(Boron)	-	0	-
Cl-7.2, Table-1 (xiii)(Copper)	-	0	-
Cl-7.2, Table-1 (xiv)(Vanadium)	-	0	-
Cl-8.1,(Mechanical properties)	-	0	-
Cl-10.1(Upsetting Test)	-	0	-
Cl-12(Retests)	-	0	-
Cl-13.2.1(Tolerances on Bright Bars)	-	0	-
Cl-13.2.1.1(Tolerance Classes)	-	0	-
Cl-13.2.1.1(Width Tolerance for Drawn Flats)	-	0	-
Cl-13.2.3(Straightness Tolerance)	-	0	-
Cl-13.2.4(Out of Shape)	-	0	-
Cl-13.2.5(Edges of Non-Round Bars)	-	0	-

-
Included w.e.f 22.07.2025 Excluding Cl. 11 Surface Quality

IS 2067 (1975)

Specification for wrought aluminium wire for electrical purposes (Fourth Revision)

All sizes

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause No 4("Chemical Composition")	-	2000	-
Clause No 5.1("Mechanical properties ")	-	1500	-
Clause No 6("Freedom from defects ")	-	500	-
Clause No 7.1(Electrical resistivity of the wire condition o, H3, H4)	-	1500	-
Clause No 8("Mechanical properties condition o, H3, H4")	-	1500	-
Clause No 9(Joints)	-	500	-
Clause No 10.1(Tolerances (on size))	-	500	-
Clause No 12.1(Tensile test)	-	1500	-
Clause No 12.2(Elongation test)	-	1500	-
Clause No 12.3(Wrapping test)	-	1500	-
Clause No 12.4.1(Electrical resistivity shall be measured at room temp.)	-	1500	-
Clause No 4("Chemical Composition")	-	0	-
Clause No 5.1("Mechanical properties ")	-	0	-
Clause No 6("Freedom from defects ")	-	0	-
Clause No 7.1(Electrical resistivity of the wire condition o, H3, H4)	-	0	-
Clause No 8("Mechanical properties condition o, H3, H4")	-	0	-
Clause No 9(Joints)	-	0	-
Clause No 10.1(Tolerances (on size))	-	0	-
Clause No 12.1(Tensile test)	-	0	-
Clause No 12.2(Elongation test)	-	0	-
Clause No 12.3(Wrapping test)	-	0	-
Clause No 12.4.1(Electrical resistivity shall be measured at room temp.)	-	0	-
Clause No 4("Chemical Composition")	-	0	-
Clause No 5.1("Mechanical properties ")	-	0	-
Clause No 6("Freedom from defects ")	-	0	-
Clause No 7.1(Electrical resistivity of the wire condition o, H3, H4)	-	0	-
Clause No 8("Mechanical properties condition o, H3, H4")	-	0	-
Clause No 9(Joints)	-	0	-
Clause No 10.1(Tolerances (on size))	-	0	-
Clause No 12.1(Tensile test)	-	0	-
Clause No 12.2(Elongation test)	-	0	-
Clause No 12.3(Wrapping test)	-	0	-
Clause No 12.4.1(Electrical resistivity shall be measured at room temp.)	-	0	-

-
Included w.e.f 22.07.2025

IS 736 (1986)

Specification for wrought aluminium and aluminium alloy plate for general engineering purposes (Third Revision)

All sizes

8500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Freedom from defect)	-	500	-
5(chemical composition)	-	500	-
6.1 table 2(0.2% proof strength)	-	1500	-
6.1 table 2(tensile strength)	-	1500	-
6.1 table 2(Elongation)	-	1000	-
5.1, Table 1(Aluminium)	-	500	-
5.1, Table 1(Copper)	-	500	-
8(Dimensions & Tolerances)	-	500	-
5.1, Table 1(Magnesium)	-	500	-
5.1, Table 1(Silicon)	-	500	-
5.1, Table 1(Iron)	-	500	-
5.1, Table 1(Mangnese)	-	500	-
5.1, Table 1(Zinc)	-	500	-
5.1, Table 1(Titanium and /or other grain refining element)	-	500	-
5.1, Table 1(Chromium)	-	500	-
5.1, Table 1(Vanadium)	-	500	-
4(Freedom from defect)	-	500	-
5(chemical composition)	-	0	-
6.1 table 2(0.2% proof strength)	-	0	-
6.1 table 2(tensile strength)	-	0	-
6.1 table 2(Elongation)	-	0	-
5.1, Table 1(Aluminium)	-	0	-
5.1, Table 1(Copper)	-	0	-
8(Dimensions & Tolerances)	-	0	-
5.1, Table 1(Magnesium)	-	0	-
5.1, Table 1(Silicon)	-	0	-
5.1, Table 1(Iron)	-	0	-
5.1, Table 1(Mangnese)	-	0	-
5.1, Table 1(Zinc)	-	0	-
5.1, Table 1(Titanium and /or other grain refining element)	-	0	-
5.1, Table 1(Chromium)	-	0	-
5.1, Table 1(Vanadium)	-	0	-

-
Included w.e.f 11.07.2025

IS 4454 : Part 2 (2001)

Steel wire for mechanical springs - Specification february 2001: Part 2 oil hardened and tempered steel wire (Second Revision)

All Size

14000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	7000	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	7000	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	7000	-
Cl 8(Workmanship)	-	7000	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
7.1, 7.2(Vanadium)	-	7000	-
7.1, 7.2(Chromium)	-	7000	-
7.1, 7.2(copper)	-	7000	-
7.1, 7.2(phosphorus)	-	7000	-
7.1, 7.2(sulphur)	-	7000	-
7.1, 7.2(manganese)	-	7000	-
7.1, 7.2(silicon )	-	7000	-
7.1, 7.2(carbon)	-	7000	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 8(Workmanship)	-	0	-
8(Freedom from defects)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 8(Workmanship)	-	0	-
8(Freedom from defects)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 8(Workmanship)	-	0	-
Cl 10(Tensile Test, Wrap Test, Torsion Test, Bend Test, Coiling and Stretching, Cast of wire, Deep Etch Test, Decarburization Test, Coating and Surface Finish & Eddy Current Test)	-	0	-
Cl 9(Diameter & Difference Between Two Reading On Any Two Diameters)	-	0	-
Cl 8(Workmanship)	-	0	-
8(Freedom from defects)	-	0	-

-
Included w.e.f 22.07.2025

IS 4368 (1967)

Specification for alloy steel billets, blooms and slabs for forging for general engineering purposes

All size

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(Freedom from Defects)	-	6000	-
Cl 8(Diameter, Ovality & Weight)	-	6000	-
Cl 11(Hardness & Tensile Test)	-	6000	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
6.1, Table-1(Ladle Analysis)	-	7000	-
9.2, table-1(Maximum Hardness Values)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
6.1, Table-1(Ladle Analysis)	-	0	-
9.2, table-1(Maximum Hardness Values)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
6.1, Table-1(Ladle Analysis)	-	0	-
9.2, table-1(Maximum Hardness Values)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 5(Freedom from Defects)	-	0	-
Cl 8(Diameter, Ovality & Weight)	-	0	-
Cl 11(Hardness & Tensile Test)	-	0	-

-
Included w.e.f 22.07.2025 Excluding Cl. 11.6 (Additional Test)

IS 2507 (1975)

Specification for cold - rolled steel strips for springs (First Revision)

All sizes

7000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Carbon- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Silicon- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Manganese- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Sulphur- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Phosphorus- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Chromium- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Vanadium- Appropriate parts of IS 228.)	-	5000	-
5(FREEDOM FROM DEFECTS)	-	5000	-
7(Rolling Tolerances)	-	5000	-
10(Physical properties(optional))	-	5000	-
12(Surface condition)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Carbon- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Silicon- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Manganese- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Sulphur- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Phosphorus- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Chromium- Appropriate parts of IS 228.)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Vanadium- Appropriate parts of IS 228.)	-	5000	-
5(FREEDOM FROM DEFECTS)	-	5000	-
7(Rolling Tolerances)	-	5000	-
10(Physical properties(optional))	-	5000	-
12(Surface condition)	-	5000	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Carbon- Appropriate parts of IS 228.)	-	0	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Silicon- Appropriate parts of IS 228.)	-	0	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Manganese- Appropriate parts of IS 228.)	-	0	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Sulphur- Appropriate parts of IS 228.)	-	0	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Phosphorus- Appropriate parts of IS 228.)	-	0	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Chromium- Appropriate parts of IS 228.)	-	0	-
Cl. 0.2, 4.1, 6.1, 6.2 & Table1(Vanadium- Appropriate parts of IS 228.)	-	0	-
5(FREEDOM FROM DEFECTS)	-	0	-
7(Rolling Tolerances)	-	0	-
10(Physical properties(optional))	-	0	-
12(Surface condition)	-	0	-

-
Included w.e.f 22.07.2025

IS 6528 (2024)

Stainless steel wire - Specification ( Second Revision )

All Size

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
As per Clause 6(FREEDOM FROM DEFECTS)	-	10000	-
As per clause 7(CARBON)	-	10000	-
As per clause 7(SILICON)	-	10000	-
As per clause 7(MANGANESE)	-	10000	-
As per clause 7(PHOSPHORUS)	-	10000	-
As per clause 7(SULPHUR)	-	10000	-
As per clause 7(CHROMIUM)	-	10000	-
As per clause 7(MOLYBEDNUM)	-	10000	-
As per clause 7(NICKEL)	-	10000	-
As per clause 7(NITROGEN)	-	10000	-
As per clause 7(COPPER)	-	10000	-
As per clause 7(NIOBIUM)	-	10000	-
As per clause 7(TITANIUM)	-	10000	-
As per clause 7(ALUMINIUM)	-	10000	-
As per clause 9(Dimension Tolerance)	-	10000	-
As per clause 10(TENSILE TEST)	-	10000	-
As per clause 10.2(REVERSE BEND TEST)	-	10000	-
As per clause 10.3(TORSION TEST)	-	10000	-
As per clause 14(FINISH)	-	10000	-
As per clause 15(CORROSION RESISTANCE)	-	10000	-
As per Clause 6(FREEDOM FROM DEFECTS)	-	0	-
As per clause 7(CARBON)	-	0	-
As per clause 7(SILICON)	-	0	-
As per clause 7(MANGANESE)	-	0	-
As per clause 7(PHOSPHORUS)	-	0	-
As per clause 7(SULPHUR)	-	0	-
As per clause 7(CHROMIUM)	-	0	-
As per clause 7(MOLYBEDNUM)	-	0	-
As per clause 7(NICKEL)	-	0	-
As per clause 7(NITROGEN)	-	0	-
As per clause 7(COPPER)	-	0	-
As per clause 7(NIOBIUM)	-	0	-
As per clause 7(TITANIUM)	-	0	-
As per clause 7(ALUMINIUM)	-	0	-
As per clause 9(Dimension Tolerance)	-	0	-
As per clause 10(TENSILE TEST)	-	0	-
As per clause 10.2(REVERSE BEND TEST)	-	0	-
As per clause 10.3(TORSION TEST)	-	0	-
As per clause 14(FINISH)	-	0	-
As per clause 15(CORROSION RESISTANCE)	-	0	-
As per Clause 6(FREEDOM FROM DEFECTS)	-	0	-
As per clause 7(CARBON)	-	0	-
As per clause 7(SILICON)	-	0	-
As per clause 7(MANGANESE)	-	0	-
As per clause 7(PHOSPHORUS)	-	0	-
As per clause 7(SULPHUR)	-	0	-
As per clause 7(CHROMIUM)	-	0	-
As per clause 7(MOLYBEDNUM)	-	0	-
As per clause 7(NICKEL)	-	0	-
As per clause 7(NITROGEN)	-	0	-
As per clause 7(COPPER)	-	0	-
As per clause 7(NIOBIUM)	-	0	-
As per clause 7(TITANIUM)	-	0	-
As per clause 7(ALUMINIUM)	-	0	-
As per clause 9(Dimension Tolerance)	-	0	-
As per clause 10(TENSILE TEST)	-	0	-
As per clause 10.2(REVERSE BEND TEST)	-	0	-
As per clause 10.3(TORSION TEST)	-	0	-
As per clause 14(FINISH)	-	0	-
As per clause 15(CORROSION RESISTANCE)	-	0	-

-
Included w.e.f 22.07.2025

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

All sizes

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	7500	-
8(Mechanical and Physical Properties)	-	7500	-
Cl 8(UTM)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	0	-
Cl 8(UTM)	-	0	-
Cl 9.5(Workmanship)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	0	-
Cl 8(UTM)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Length, Width & Thickness)	-	0	-
7.0(MICRO ALLOYS)	-	0	-
7.0(ALUMINIUM)	-	0	-
7.0(NITROGEN)	-	0	-
7.0(SILICON)	-	0	-
7.0(MANGANESE)	-	0	-
7.0(PHOSPHORUS)	-	0	-
7.0(SULPHUR)	-	0	-
7.0(CARBON)	-	0	-
Cl. 11(Out of square)	-	0	-
Cl. 11(Flatness)	-	0	-
Cl. 11(Camber)	-	0	-
Cl. 11(Width)	-	0	-
Cl. 11(Thickness)	-	0	-
Cl. 8.7(Bake Hardening Index)	-	0	-
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	0	-
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	0	-
Cl. 8.4(Bend Test)	-	0	-
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	0	-
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 80 mm gauge length)	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 50 mm gauge length)	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Yield Stress)	-	0	-
Cl. 9 Table 8(Surface roughness)	-	0	-
Cl 11(Length, Width & Thickness)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 8(UTM)	-	0	-
Cl 8(UTM)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Thickness (08))	-	0	-
Cl 7(UTM)	-	0	-
8.1(Mechanical)	-	0	-
8.2(Cupping test)	-	0	-
8.3(Hardness HRB/HV)	-	0	-
8.4(Bend Test)	-	0	-
8.5(Plastic strain ratio)	-	0	-
8.6(Tensile strain Hardening component)	-	0	-
8.7(Black Hardening Index)	-	0	-
10(Freedom from defects)	-	0	-
Cl. 7.3(Carbon)	-	0	-
Cl. 7.3(Manganese)	-	0	-
Cl. 7.3(Suphur)	-	0	-
Cl. 7.3(Phosphorus)	-	0	-
Cl. 7.3(Silicon)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
9(Surface finish)	-	0	-
7(Chemical Composition)	-	0	-
8(Mechanical and Physical Properties)	-	0	-
Cl. 11(Out of square)	-	0	-
Cl. 11(Flatness)	-	0	-
Cl. 11(Camber)	-	0	-
Cl. 11(Width)	-	0	-
Cl. 11(Thickness)	-	0	-
Cl. 8.7(Bake Hardening Index)	-	0	-
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	0	-
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	0	-
Cl. 8.4(Bend Test)	-	0	-
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	0	-
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 80 mm gauge length)	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 50 mm gauge length)	-	0	-
Cl. 8.1 & Table 5A, 5B & 5C(Yield Stress)	-	0	-
Cl. 9 Table 8(Surface roughness)	-	0	-
Cl 11(Length, Width & Thickness)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 8(UTM)	-	0	-
Cl 8(UTM)	-	0	-
Cl 10(Workmanship)	-	0	-
Cl 11(Thickness (08))	-	0	-
Cl 7(UTM)	-	0	-
8.1(Mechanical)	-	0	-
8.2(Cupping test)	-	0	-
8.3(Hardness HRB/HV)	-	0	-
8.4(Bend Test)	-	0	-
8.5(Plastic strain ratio)	-	0	-
8.6(Tensile strain Hardening component)	-	0	-
8.7(Black Hardening Index)	-	0	-
10(Freedom from defects)	-	0	-
Cl. 7.3(Carbon)	-	0	-
Cl. 7.3(Manganese)	-	0	-
Cl. 7.3(Suphur)	-	0	-
Cl. 7.3(Phosphorus)	-	0	-
Cl. 7.3(Silicon)	-	0	-
Cl 9.6(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 9(Workmanship)	-	0	-
Cl 9.6(Workmanship)	-	0	-
9(Surface finish)	-	0	-

-
Included w.e.f 11.07.2025

100

IS 2879 (1998)

Mild steel for metal arc welding electrodes - Specification (Third Revision)

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Workmanship)	-	650	-
Cl 8 & 9(Diameter)	-	500	-
Cl 7(Workmanship)	-	500	-
Cl 8 & 9(Diameter)	-	500	-
Cl 7(Workmanship)	-	500	-
Cl 8 & 9(Diameter)	-	500	-
6(Carbon %)	-	500	-
6(Manganese %)	-	500	-
6(Phosphorus %)	-	500	-
6(Sulphur %)	-	500	-
6(Silicon %)	-	500	-
6( Copper %)	-	500	-
6( Aluminium %)	-	500	-
6( Nb)	-	500	-
6(V)	-	500	-
6( Ti)	-	500	-
6(Cr)	-	500	-
6(Mo)	-	500	-
6(Ni)	-	500	-
6(Cr+ Mo+ Ni)	-	500	-
6(Carbon %)	-	500	-
6(Manganese %)	-	500	-
6(Phosphorus %)	-	500	-
6(Sulphur %)	-	500	-
6(Silicon %)	-	500	-
6( Copper %)	-	500	-
6( Aluminium %)	-	500	-
6( Nb)	-	500	-
6(V)	-	500	-
6( Ti)	-	500	-
6(Cr)	-	500	-
6(Mo)	-	500	-
6(Ni)	-	500	-
6(Cr+ Mo+ Ni)	-	500	-
6(Carbon %)	-	500	-
6(Manganese %)	-	500	-
6(Phosphorus %)	-	500	-
6(Sulphur %)	-	500	-
6(Silicon %)	-	500	-
6( Copper %)	-	500	-
6( Aluminium %)	-	500	-
6( Nb)	-	500	-
6(V)	-	500	-
6( Ti)	-	500	-
6(Cr)	-	500	-
6(Mo)	-	500	-
6(Ni)	-	500	-
6(Cr+ Mo+ Ni)	-	500	-
Cl. 9.2(Maximum Difference between 2 readings taken at any 2 diameters across cross section)	-	500	-
Cl. 8,9(Width across flat)	-	500	-
Cl. 8,9(Length)	-	500	-
Cl. 5.2(Macro Examination)	-	500	-
Cl 8 & 9(Diameter)	-	500	-
Cl 7(Workmanship)	-	500	-
Cl 7(Workmanship)	-	500	-
Cl 8 & 9(Diameter)	-	500	-
9.2 (a)(Width Across Flat)	-	500	-
9.2 (b)(Diameter Difference)	-	500	-

-
Included w.e.f 24.04.2025

101

IS 7092 : Part 2 (1987)

Specification for aluminium alloy tube for irrigation purposes: Part 2 extruded tube (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl.6.2(Ultimate Tensile Strength- IS 2657)	-	1600	-
Cl.4(Workmanship & Finish)	-	500	-
Cl.6.2(0.2 percent proof strength- IS 2657)	-	1200	-
Cl.6.2(Elongation on 50 mm gauge length- IS 2657)	-	1000	-
Cl. 6.3(Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-	1500	-
Cl.7.1, Table 2(Roundness or Ovality)	-	500	-
Cl.7.1, Table 2(Outside Diameter-)	-	500	-
Cl. 7.2(Length)	-	500	-
Cl. 6.1(Copper- IS 504 or any other established instrumental/ chemical method)	-	350	-
Cl. 6.1(Magnesium- IS 504 or any other established instrumental/ chemical method)	-	350	-
Cl. 6.1(Silicon- IS 504 or any other established instrumental/ chemical method)	-	350	-
Cl. 6.1(Iron- IS 504 or any other established instrumental/ chemical method)	-	350	-
Cl. 6.1(Manganese- IS 504 or any other established instrumental/ chemical method)	-	350	-
Cl. 6.1(Zinc- IS 504 or any other established instrumental/ chemical method)	-	350	-
Cl. 6.1(Chromium- IS 504 or any other established instrumental/ chemical method)	-	350	-
Cl. 6.1(Titanium and/ other grain refining elements)	-	350	-
Cl. 6.1(Aluminium- IS 504 or any other established instrumental/ chemical method)	-	350	-
14(Workmanship & Finish)	-	350	-
7.1(Dimensions)	-	350	-
6.2(Mechanical properties)	-	2500	-
6.3(Drift Expanding Test)	-	1500	-
6.3(Drift expanding test)	-	1500	-
7.1 table 2(Dimensions and tolerances for extruded tubes)	-	1200	-
6.1(chemical composition)	-	1500	-
6.2(ultimate tensile strength)	-	1600	-
6.2(0.2% proof strength)	-	1500	-
6.2(Elongation on 50 mm gauge length)	-	1000	-
Cl.7.1, Table 2(Wall Thickness)	-	500	-
6.4(Drift Expanding Testt)	-	1200	-
Cl.6.2(Ultimate Tensile Strength- IS 2657)	-	1600	-
Cl.4(Workmanship & Finish)	-	500	-
Cl.6.2(0.2 percent proof strength- IS 2657)	-	1500	-
Cl.6.2(Elongation on 50 mm gauge length- IS 2657)	-	1000	-
Cl. 6.3(Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-	1500	-
Cl.7.1, Table 2(Roundness or Ovality)	-	500	-
Cl.7.1, Table 2(Outside Diameter-)	-	500	-
Cl. 7.2(Length)	-	500	-
Cl. 6.1(Copper- IS 504 or any other established instrumental/ chemical method)	-	500	-
Cl. 6.1(Magnesium- IS 504 or any other established instrumental/ chemical method)	-	500	-
Cl. 6.1(Silicon- IS 504 or any other established instrumental/ chemical method)	-	500	-
Cl. 6.1(Iron- IS 504 or any other established instrumental/ chemical method)	-	500	-
Cl. 6.1(Manganese- IS 504 or any other established instrumental/ chemical method)	-	500	-
Cl. 6.1(Zinc- IS 504 or any other established instrumental/ chemical method)	-	500	-
Cl. 6.1(Chromium- IS 504 or any other established instrumental/ chemical method)	-	500	-
Cl. 6.1(Titanium and/ other grain refining elements)	-	500	-
Cl. 6.1(Aluminium- IS 504 or any other established instrumental/ chemical method)	-	500	-
14(Workmanship & Finish)	-	500	-
7.1(Dimensions)	-	500	-
6.2(Mechanical properties)	-	1600	-
6.3(Drift Expanding Test)	-	1500	-
6.3(Drift expanding test)	-	1500	-
7.1 table 2(Dimensions and tolerances for extruded tubes)	-	500	-
6.1(chemical composition)	-	500	-
6.2(ultimate tensile strength)	-	1600	-
6.2(0.2% proof strength)	-	1600	-
6.2(Elongation on 50 mm gauge length)	-	1000	-
Cl.7.1, Table 2(Wall Thickness)	-	500	-
6.4(Drift Expanding Testt)	-	1000	-
Cl.6.2(Ultimate Tensile Strength- IS 2657)	-	-	-
Cl.4(Workmanship & Finish)	-	-	-
Cl.6.2(0.2 percent proof strength- IS 2657)	-	-	-
Cl.6.2(Elongation on 50 mm gauge length- IS 2657)	-	-	-
Cl. 6.3(Drift Expanding Test ( Expanded Inside Diameter- IS 2335)	-	-	-
Cl.7.1, Table 2(Roundness or Ovality)	-	-	-
Cl.7.1, Table 2(Outside Diameter-)	-	-	-
Cl. 7.2(Length)	-	-	-
Cl. 6.1(Copper- IS 504 or any other established instrumental/ chemical method)	-	-	-
Cl. 6.1(Magnesium- IS 504 or any other established instrumental/ chemical method)	-	-	-
Cl. 6.1(Silicon- IS 504 or any other established instrumental/ chemical method)	-	-	-
Cl. 6.1(Iron- IS 504 or any other established instrumental/ chemical method)	-	-	-
Cl. 6.1(Manganese- IS 504 or any other established instrumental/ chemical method)	-	-	-
Cl. 6.1(Zinc- IS 504 or any other established instrumental/ chemical method)	-	-	-
Cl. 6.1(Chromium- IS 504 or any other established instrumental/ chemical method)	-	-	-
Cl. 6.1(Titanium and/ other grain refining elements)	-	-	-
Cl. 6.1(Aluminium- IS 504 or any other established instrumental/ chemical method)	-	-	-
14(Workmanship & Finish)	-	-	-
7.1(Dimensions)	-	-	-
6.2(Mechanical properties)	-	-	-
6.3(Drift Expanding Test)	-	-	-
6.3(Drift expanding test)	-	-	-
7.1 table 2(Dimensions and tolerances for extruded tubes)	-	-	-
6.1(chemical composition)	-	-	-
6.2(ultimate tensile strength)	-	-	-
6.2(0.2% proof strength)	-	-	-
6.2(Elongation on 50 mm gauge length)	-	-	-
Cl.7.1, Table 2(Wall Thickness)	-	-	-
6.4(Drift Expanding Testt)	-	-	-

-
Included w.e.f 18.06.2025 Exclusion: Cl 6.4 Hydrostatic Pressure

102

IS 1254 (2007)

Corrugated aluminium sheet (Fourth Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(FREEDOM FROM DEFECTS)	-	500	-
5(PROFILE)	-	500	-
7.2(WIDTH)	-	500	-
7.3(LENGTH)	-	500	-
7.4(SQUARENESS)	-	500	-
7.5(Depth and Pitch of the Corrugation)	-	500	-
8(FINISH)	-	500	-
6(MATERIAL)	-	7500	-
3(FREEDOM FROM DEFECTS)	-	1000	-
5(PROFILE)	-	500	-
7.2(WIDTH)	-	500	-
7.3(LENGTH)	-	500	-
7.4(SQUARENESS)	-	500	-
7.5(Depth and Pitch of the Corrugation)	-	500	-
8(FINISH)	-	500	-
6(MATERIAL)	-	7500	-

-
Included w.e.f 18.06.2025

103

IS 4026 (2023)

ALUMINIUM INGOTS BILLETS AND WIRE BARS EC GRADE

5500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(SHAPES AND SIZES)	-	500	-
9, Table 1, i)(Aluminium, Min)	-	500	-
9, Table 1, ii)(Silicon)	-	500	-
9, Table 1, iii)(Iron)	-	500	-
9, Table 1, iv)(Copper)	-	500	-
9, Table 1, v)(Manganese)	-	500	-
9, Table 1, vi)(Magnesium)	-	500	-
9, Table 1, vii)(Chromium)	-	500	-
9, Table 1, ix)(Titanium)	-	500	-
9, Table 1, x)(Boron)	-	500	-
9, Table 1, xi)(Gallium)	-	500	-
9, Table 1, xii)(Zirconium)	-	500	-
9, Table 1, xiii)(Titanium + Vanadium)	-	500	-
9, Table 1, xiv)(Other elements (each))	-	500	-
9, Table 1, xv)(Other elements (Total))	-	500	-
9, Table 1, viii)(Zinc)	-	500	-

-
Included w.e.f 18.06.2025

104

IS 9997 (2023)

ALUMINIUM ALLOY REDRAW RODS FOR ELECTRICAL PURPOSES - SPECIFICATION

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl-7.1, Table-2 (i)(Silicon)	-	300	-
Cl-7.1, Table-2 (ii)(Iron)	-	300	-
Cl-7.1, Table-2 (iii)(Copper)	-	300	-
Cl-7.1, Table-2 (iv)(Manganese)	-	300	-
Cl-7.1, Table-2 (v)(Magnesium)	-	300	-
Cl-7.1, Table-2 (vi)(Chromium)	-	300	-
Cl-7.1, Table-2 (vii)(Zinc)	-	300	-
Cl-7.1, Table-2 (viii)(Boron)	-	300	-
Cl-7.1, Table-2 (ix)(Vanadium + Titanium)	-	300	-
Cl-7.1, Table-2 (x)(Other each)	-	300	-
Cl-7.1, Table-2 (xi)(Others total)	-	300	-
Cl-7.1, Table-2 (xii)(Aluminium)	-	300	-
Cl-8.1, Table-3(UTS (MPa))	-	1000	-
Cl-8.1, Table-3(Elongation (%) - On 250 mm gauge length)	-	800	-
Cl-8.1, Table-3(Resistivity (micro ohm.cm) at 20 oC)	-	1500	-
Cl-8.1, Table-3(Conductivity (%) (IACS))	-	1000	-
Cl-9(Electrical resistivity)	-	1000	-
Cl-10(Diameter and Permissible Variations)	-	500	-
Cl-12(Finish and freedom from defects)	-	500	-

-
Included w.e.f 18.06.2025

105

IS 18316 (2023)

HOT ROLLED AND COLD ROLLED STEEL STRIPS INTENDED FOR PROCESSING OF SEMIFULLY PROCESSED NON-GRAIN ORIENTED ELECTRICAL STEEL OR FULLY PROCESSED GRAIN ORIENTED ELECTRICAL STEEL SPECIFICATION

10500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause. 7.0(Carbon)	-	1000	-
Clause. 7.0(Silicon)	-	1000	-
Clause. 7.0(Sulphur)	-	1000	-
Clause. 7.0(Phosphorus)	-	1000	-
Clause. 7.0(Manganese)	-	1000	-
Clause. 7.0(Aluminium)	-	1000	-
Clause.8.0(Freedom From Defects)	-	1000	-
Clause.9.0(Dimensions, Shape & Tolerances (for Hot-rolled Steel))	-	1000	-
Clause.10.0(Dimensions, Shape & Tolerances (for Cold-rolled Steel))	-	1000	-

-
Included w.e.f 18.06.2025

106

IS 739 (1992)

Wrought aluminium and aluminium alloys - Wire for general engineering purposes - Specification (Third Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.0(Freedom from defects)	-	500	-
7.0(Dimension and Tolerances)	-	1000	-
8.1 Table-1(Al)	-	500	-
8.1 Table-1(Cu)	-	500	-
8.1 Table-1(Mg)	-	500	-
8.1 Table-1(Si)	-	500	-
8.1 Table-1(Fe)	-	500	-
8.1 Table-1(Mn)	-	500	-
8.1 Table-1(Zn)	-	500	-
8.1 Table-1(Ti)	-	500	-
8.1 Table-1(Cr)	-	500	-
9.1(Tensile Strength)	-	1000	-
9.3(Wrapping Test)	-	1500	-
10(Selection of Test Samples)	-	500	-

-
Included w.e.f 18.06.2025

107

IS 734 (1975)

Specification for wrought aluminium and aluminium alloy forging stock and forgings (For General Engineering Purposes) (Second Revision)

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 table 1(chemical composition)	-	2500	-
5.1 table 2(0.2% proof strength)	-	1000	-
5.1 table 2(Tensile strength)	-	1000	-
5.1 table 2(Elongation)	-	1000	-
Cl.5.1(Aluminium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Copper - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Magnesium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Silicon - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Iron - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Manganese - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Zinc - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Titanium And/or Other Grain Refining Elements - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Chromium - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
Cl.5.1(Remarks (Cu + Mg + Si + Fe + Mn + Zn) - IS 504 and its parts or any other intrumental/chemical methods)	-	500	-
4.1(Freedom from defects)	-	500	-
9.1(Tensile test)	-	1500	-

-
Included w.e.f 18.06.2025

108

IS 2590 (1987)

Specification for primary aluminium ingots for remelting for general engineering purposes (Second Revision)

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5(Grades)	-	2500	-
6.1(Chemical composition )	-	2500	-
7.1(Shapes and sizes)	-	500	-
Table-1, Clause - 6.1.1(Copper)	-	500	-
Table-1, Clause - 6.1.1(Iron)	-	500	-
Table-1, Clause - 6.1.1(Magnesium)	-	500	-
Table-1, Clause - 6.1.1(Manganese)	-	500	-
Table-1, Clause - 6.1.1(Titanium + Vanadium)	-	500	-
Table-1, Clause - 6.1.1(Silicon)	-	500	-
Table-1, Clause - 6.1.1(Vanadium)	-	500	-
Table-1, Clause - 6.1.1(Zinc)	-	500	-
Table-1, Clause - 6.1.1(Other elements (each))	-	500	-
Table-1, Clause - 6.1.1(Others Total)	-	500	-
Table-1, Clause - 6.1.1(Aluminium)	-	500	-

-
Included w.e.f 18.06.2025

109

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8 & Table 3(UTM)	-	1200	-
Cl 9(Press)	-	800	-
Cl 11(Workmanship)	-	500	-
Cl 12 & 13(Length, Width & Thickness)	-	500	-
Cl 8 & Table 3(UTM)	-	500	-
Cl 9(Press)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 12 & 13(Length, Width & Thickness)	-	500	-
Cl 8 & Table 3(UTM)	-	500	-
Cl 9(Press)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 12 & 13(Length, Width & Thickness)	-	500	-
7.1(Carbon %)	-	300	-
7.1(Manganese %)	-	300	-
7.1(Phosphorus %)	-	300	-
7.1(Sulphur %)	-	300	-
7.1( Copper %)	-	300	-
7.1(Silicon %)	-	300	-
7.1( Aluminium %)	-	300	-
7.1( Nb)	-	300	-
7.1(V)	-	300	-
7.1( Ti)	-	300	-
7.1(Cr)	-	300	-
7.1(Ni)	-	300	-
7.1( Nitrogen%)	-	300	-
7.1(CE)	-	300	-
7.1(Manganese %)	-	300	-
7.1(Phosphorus %)	-	300	-
7.1(Sulphur %)	-	300	-
7.1(Silicon %)	-	300	-
7.1( Copper %)	-	300	-
7.1( Aluminium %)	-	300	-
7.1( Nb)	-	300	-
7.1(V)	-	300	-
7.1( Ti)	-	300	-
7.1(Cr)	-	300	-
7.1(Mo)	-	300	-
7.1(Ni)	-	300	-
7.1( Nitrogen%)	-	300	-
7.1(CE)	-	300	-
7.1(Carbon %)	-	300	-
7.1(Manganese %)	-	300	-
7.1(Phosphorus %)	-	300	-
7.1(Sulphur %)	-	300	-
7.1(Silicon %)	-	300	-
7.1( Copper %)	-	300	-
7.1( Aluminium %)	-	300	-
7.1( Nb)	-	300	-
7.1(V)	-	300	-
7.1( Ti)	-	300	-
7.1(Cr)	-	300	-
7.1(Mo)	-	300	-
7.1(Ni)	-	300	-
7.1( Nitrogen%)	-	300	-
7.1(CE)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(TITANIUM)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(VANADIUM)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(NIOBIUM)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(CARBON EQUIVELENT )	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(Molybdenum)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(Chromium)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(Nickel)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )( ALUMINIUM)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(SILICON)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(NITROGEN)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(MANGANESE)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(PHOSPHURS)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )(SULPHUR)	-	300	-
Table 1 ( Clauses 7.1 ,7.2 )( CARBON)	-	300	-
Cl. 14(Weight)	-	300	-
Cl. 12, 13(Camber)	-	300	-
Cl. 12, 13(Thickness)	-	300	-
Cl. 8, Table 3(Elongation)	-	300	-
Cl. 8, Table 3(Yield Stress)	-	1000	-
Cl 12 & 13(Length, Width & Thickness)	-	500	-
Cl 11(Workmanship)	-	500	-
Cl 9(Press)	-	500	-
Cl 8 & Table 3(UTM)	-	1200	-
Cl 8 & Table 3(UTM)	-	1200	-
Cl 9(Press)	-	1200	-
Cl 11(Workmanship)	-	500	-
Cl 12 & 13(Length, Width & Thickness)	-	500	-
7.0 (7)(Micro Alloying elements - IS:8811)	-	500	-
8.0 (1)(Tensile Strength-IS:1608(P1))	-	500	-
8.0 (2)(Yield Strength-IS:1608(P1))	-	500	-
8.0 (3)(Elongation on 5.65 SoA GL-IS:1608(P1))	-	500	-
12 (1)(Width - SOP MT-23)	-	500	-
12 (2)(Thickness- SOP MT-23)	-	500	-
12 (3)(Mass of Strip- SOP MT-23)	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(Tungsten (W))	-	500	-
Table 1 ( Clauses 7.1 ,7.2 )(Boron (B))	-	500	-
9(Protective Treatment)	-	500	-
7.1(Mo)	-	500	-
7.1(Carbon %)	-	500	-

-
Included w.e.f 18.06.2025

110

IS 12145 (1987)

Specification for quenched and tempered alloy steel forgings for pressure vessels

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
8(Shape dimension and tolerence)	-	500	-
7(Appearance)	-	500	-
6.1Table4 9.2.1(Impact test,Individual value)	-	3500	-
6.1Table4 9.2.1(Impact test,Mean of three test pieces)	-	3500	-
6.1Table4 9.2.1(Reduction in area,Min )	-	500	-
6.1Table4 9.2.1(Yield strength, Min)	-	1000	-
6.1Table4 9.2.1(Yield strength)	-	1000	-
6.1Table4 9.2.2(Tensile Strength,)	-	1000	-
6.1Table4 9.2.1(MECHANICAL PROPERTIES OF STEEL FORGINGS )	-	3000	-
Clause 5.1(Vanadium)	-	250	-
Clause 5.1(Molybdenum)	-	300	-
Clause 5.1(Chromium)	-	300	-
Clause 5.1(Nickel)	-	300	-
Clause 5.1(Silicon)	-	300	-
Clause 5.1(Phosphorous)	-	300	-
Clause 5.1(Sulphur)	-	300	-
Clause 5.1 (Manganese)	-	300	-
Clause 5.1 (Carbon)	-	300	-
Cl. 5(Carbon)	-	300	-
Cl. 5(Carbon)	-	300	-
Cl. 5(Silicon)	-	300	-
Cl. 5(Manganese)	-	300	-
Cl. 5(Nickel)	-	300	-
Cl. 5(Chromium)	-	300	-
Cl. 5(Molybdenum)	-	300	-
Cl. 5(Vanadium)	-	300	-
Cl. 5(Sulphur)	-	300	-
Cl. 5(Phosphorous)	-	300	-

-
Included w.e.f 18.06.2025

111

IS 1117 (2018)

Laboratory glassware - Single - Volume pipettes (Second Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4(i) Distance of graduation line from top of pipette.)	-	200	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	200	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	200	-
5.4(iv) Wall thickness)	-	200	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	200	-
5.4(b) Other pipettes)	-	200	-
5.4(vii) Overall length, L)	-	200	-
5.4(viii) Length of suction tube, L1 )	-	200	-
5.4(xi) External dia. of bulb D2 )	-	200	-
5.4(xii) External dia. of delivery tube D3 )	-	200	-
5.5(Delivery Time)	-	200	-
5.5(Delivery Time)	-	200	-
4.1(Nominal capacities)	-	200	-
5.4(i) Distance of graduation line from top of pipette.)	-	200	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	200	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	200	-
5.4(iv) Wall thickness)	-	200	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	200	-
5.4(b) Other pipettes)	-	200	-
5.4(vii) Overall length, L)	-	200	-
5.4(viii) Length of suction tube, L1 )	-	200	-
5.4(ix) Length of delivery tube, L2 )	-	200	-
5.4(xi) External dia. of bulb D2 )	-	200	-
5.4(xii) External dia. of delivery tube D3 )	-	200	-
5.5(Delivery Time)	-	200	-
5.5(Delivery Time)	-	200	-
5.6&7(Graduation line & Visibility )	-	200	-
4.1(Nominal capacities)	-	200	-
5.4(i) Distance of graduation line from top of pipette.)	-	200	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	200	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	200	-
5.4(iv) Wall thickness)	-	200	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	200	-
5.4(b) Other pipettes)	-	200	-
5.4(vii) Overall length, L)	-	200	-
5.4(viii) Length of suction tube, L1 )	-	200	-
5.4(ix) Length of delivery tube, L2 )	-	200	-
5.4(xi) External dia. of bulb D2 )	-	200	-
5.4(xii) External dia. of delivery tube D3 )	-	200	-
5.5(Delivery Time)	-	200	-
5.5(Delivery Time)	-	200	-
4.1(unit of volume)	-	200	-
4.2(delivery volume)	-	200	-
4.3(reference temperature)	-	200	-
Clause- 6.0(Maximum Permissible error)	-	200	-
7.4(Dimensions)	-	200	-
7.5(Top of Pipette)	-	200	-
7.8(Waiting Time)	-	200	-
7.7(Delivery Time)	-	200	-
Clause- 9.0(Setting of the Meniscus)	-	200	-
5.4(ix) Length of delivery tube, L2 )	-	200	-
5.4(i) Distance of graduation line from top of pipette.)	-	0	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	0	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	0	-
5.4(iv) Wall thickness)	-	0	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	0	-
5.4(b) Other pipettes)	-	0	-
5.4(vii) Overall length, L)	-	0	-
5.4(viii) Length of suction tube, L1 )	-	0	-
5.4(xi) External dia. of bulb D2 )	-	0	-
5.4(xii) External dia. of delivery tube D3 )	-	0	-
5.5(Delivery Time)	-	0	-
5.5(Delivery Time)	-	0	-
4.1(Nominal capacities)	-	0	-
5.4(i) Distance of graduation line from top of pipette.)	-	0	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	0	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	0	-
5.4(iv) Wall thickness)	-	0	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	0	-
5.4(b) Other pipettes)	-	0	-
5.4(vii) Overall length, L)	-	0	-
5.4(viii) Length of suction tube, L1 )	-	0	-
5.4(ix) Length of delivery tube, L2 )	-	0	-
5.4(xi) External dia. of bulb D2 )	-	0	-
5.4(xii) External dia. of delivery tube D3 )	-	0	-
5.5(Delivery Time)	-	0	-
5.5(Delivery Time)	-	0	-
4.1(Nominal capacities)	-	0	-
5.4(i) Distance of graduation line from top of pipette.)	-	0	-
5.4(ii) Distance from graduation line to top of bulb(pattern 2))	-	0	-
5.4(iii)Distance from graduation line to tip of jet (Pattern 1))	-	0	-
5.4(iv) Wall thickness)	-	0	-
5.4(a) pattern 2 pipette of 1 and 2ml )	-	0	-
5.4(b) Other pipettes)	-	0	-
5.4(vii) Overall length, L)	-	0	-
5.4(viii) Length of suction tube, L1 )	-	0	-
5.4(ix) Length of delivery tube, L2 )	-	0	-
5.4(xi) External dia. of bulb D2 )	-	0	-
5.4(xii) External dia. of delivery tube D3 )	-	0	-
5.5(Delivery Time)	-	0	-
5.5(Delivery Time)	-	0	-
4.1(unit of volume)	-	0	-
4.2(delivery volume)	-	0	-
4.3(reference temperature)	-	0	-
Clause- 6.0(Maximum Permissible error)	-	0	-
7.4(Dimensions)	-	0	-
7.5(Top of Pipette)	-	0	-
7.8(Waiting Time)	-	0	-
7.7(Delivery Time)	-	0	-
Clause- 9.0(Setting of the Meniscus)	-	0	-
5.4(ix) Length of delivery tube, L2 )	-	0	-

-
Included w.e.f 22.07.2025

112

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

6000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Workmanship)	-	300	-
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	1000	-
Cl 8(Workmanship)	-	300	-
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	1000	-
Cl 8(Workmanship)	-	300	-
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	1000	-
6.1(Carbon %)	-	250	-
6.1(Manganese %)	-	250	-
6.1(Phosphorus %)	-	250	-
6.1(Sulphur %)	-	250	-
6.1(Silicon %)	-	250	-
6.1( Copper %)	-	250	-
6.1( Aluminium %)	-	250	-
6.1( Nb)	-	250	-
6.1(V)	-	250	-
6.1( Ti)	-	250	-
6.1(Boron)	-	250	-
6.1( Nitrogen%)	-	250	-
6.1(Microalloying)	-	250	-
6.1(Carbon %)	-	250	-
6.1(Manganese %)	-	250	-
6.1(Phosphorus %)	-	250	-
6.1(Sulphur %)	-	250	-
6.1(Silicon %)	-	250	-
6.1( Copper %)	-	250	-
6.1( Aluminium %)	-	250	-
6.1( Nb)	-	250	-
6.1(V)	-	250	-
6.1( Ti)	-	250	-
6.1(Boron)	-	250	-
6.1( Nitrogen%)	-	250	-
6.1(Microalloying)	-	250	-
6.1(Carbon %)	-	250	-
6.1(Manganese %)	-	250	-
6.1(Phosphorus %)	-	250	-
6.1(Sulphur %)	-	250	-
6.1(Silicon %)	-	250	-
6.1( Copper %)	-	250	-
6.1( Aluminium %)	-	250	-
6.1( Nb)	-	250	-
6.1(V)	-	250	-
6.1( Ti)	-	250	-
6.1(Boron)	-	250	-
6.1( Nitrogen%)	-	250	-
6.1(Microalloying)	-	250	-
Cl. 10(Weight)	-	250	-
Cl. 9.3(Crown)	-	250	-
Cl.9.3.1(Difference in Thickness)	-	250	-
Cl. 9.5(Edge Camber)	-	250	-
Cl.9(Thickness)	-	250	-
Cl.9(Width)	-	250	-
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	500	-
Cl 8(Workmanship)	-	250	-
Cl 8(Workmanship)	-	250	-
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width)	-	500	-

-
Included w.e.f 02.06.2025

113

IS 12594 (1988)

Hot - Dip zinc coating on structural steel bars for concrete reinforcement - Specification

7500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1 , Table 1(Mass of Zinc coating , IS 6745)	-	1500	-
5.2(Freedom from defects , IS 2629)	-	1000	-
5.3(Adhesion of Galvanized coating)	-	500	-
5,5.4.1,5.4.2(Chromating)	-	1000	-
5.1 , Table 1(Mass of Zinc coating , IS 6745)	-	1000	-
5.3(Adhesion of Galvanized coating)	-	1000	-
5,5.4.1,5.4.2(Chromating)	-	1000	-
Clause - 4, 4.1(CARBON)	-	1000	-
Clause - 4, 4.1(SULPHUR)	-	500	-
Clause - 4, 4.1(PHOSPHURS)	-	500	-
Clause - 4, 4.1(MANGANESE)	-	500	-
Clause - 4, 4.1(NITROGEN)	-	500	-
Clause - 4, 4.1(SILICON)	-	500	-
Clause - 4, 4.1(ALUMINIUM)	-	500	-
8,8.1(Supplementary requirements of galvanized coating --Sheared End)	-	500	-
8,8.2(Supplementary requirements of galvanized coating --Damaged coating)	-	500	-
8,8.1(Supplementary requirements of galvanized coating --Sheared End)	-	500	-
8,8.2(Supplementary requirements of galvanized coating --Damaged coating)	-	500	-
5.2(Freedom from defects , IS 2629)	-	500	-

-
Included w.e.f 21.05.2025

114

IS 7226 (1974)

Specification for cold - Rolled medium, high carbon and low alloy steel strip for general engineering purposes

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4.1 Table 1(Carbon- IS 228)	-	1000	-
4.1 Table 1(Manganese- IS 228)	-	1000	-
4.1 Table 1(Silicon- IS 228)	-	1000	-
4.1 Table 1(Sulphur- IS 228)	-	1000	-
4.1 Table 1(Phosphorous- IS 228)	-	1000	-
4.1 Table 1(Chromium- IS 228)	-	1000	-
4.1 Table 1(Tungsten- IS 228)	-	1000	-
5(HARDNESS TEST)	-	1000	-
6( FREEDOM FROM DEFECTS)	-	1000	-
9.1, Table 3(i)TOLERANCE ON WIDTH)	-	1000	-
9.1, Table 4(ii)TOLERANCE ON THICKNESS)	-	1000	-
9.2( Camber)	-	1000	-
10(SURFACE FINISH)	-	1000	-

-
Included w.e.f 19.05.2025

115

IS 3195 (1992)

Steel for the manufacture of volute and helical springs (For Railway Rolling Stock) - Specification (Third Revision)

12500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 3, 6.1, 6.2 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	-
7(Hardness)	-	1000	-
8(Decarburisation)	-	1000	-
9(Inclusion rating)	-	1000	-
10(Freedom from defects)	-	1000	-
11( DIMENSIONS AND TOLERANCES)	-	1000	-
12(Calculation of mass)	-	1000	-
Cl. 3, 6.1, 6.2 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
7(Hardness)	-	1500	-
8(Decarburisation)	-	2000	-
9(Inclusion rating)	-	1000	-
10(Freedom from defects)	-	500	-
11( DIMENSIONS AND TOLERANCES)	-	500	-
12(Calculation of mass)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
Cl. 3, 6.1, 6.2 & Table 1(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	-
7(Hardness)	-	1500	-
8(Decarburisation)	-	3000	-
9(Inclusion rating)	-	3000	-
10(Freedom from defects)	-	1000	-
11( DIMENSIONS AND TOLERANCES)	-	1000	-
12(Calculation of mass)	-	1000	-

-
Included w.e.f 19.05.2025

116

IS 11169 : Part 1 (2022)

Specification for steels for cold heading cold extrusion applications: Part 1 wrought carbon and low alloy steels

All Size of Bars, Wire Rods and Wires

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
17(Shape, Dimensions and tolerances)	-	10000	-
8.1(Tensile Test)	-	10000	-
8.1(Hardness Test)	-	10000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	10000	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	10000	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	10000	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	10000	-
Cl. 7(Carbon)	-	10000	-
Cl. 7(Sulphur)	-	10000	-
Cl. 7(Phosphorous)	-	10000	-
Cl. 7(Manganese)	-	10000	-
Cl. 7(Silicon)	-	10000	-
Cl. 7(Nickel)	-	10000	-
Cl. 7(Chromium)	-	10000	-
Cl. 7(Aluminium)	-	10000	-
Cl. 7(Molybdenum)	-	10000	-
Cl. 7(Boron)	-	10000	-
Cl. 7(Copper)	-	10000	-
Cl. 7(Cr+Ni+Mo)	-	10000	-
Cl. 7(Sn)	-	10000	-
Cl. 7(V)	-	10000	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	10000	-
17(Shape, Dimensions and tolerances)	-	0	-
8.1(Tensile Test)	-	0	-
8.1(Hardness Test)	-	0	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	0	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	0	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl. 7(Carbon)	-	0	-
Cl. 7(Sulphur)	-	0	-
Cl. 7(Phosphorous)	-	0	-
Cl. 7(Manganese)	-	0	-
Cl. 7(Silicon)	-	0	-
Cl. 7(Nickel)	-	0	-
Cl. 7(Chromium)	-	0	-
Cl. 7(Aluminium)	-	0	-
Cl. 7(Molybdenum)	-	0	-
Cl. 7(Boron)	-	0	-
Cl. 7(Copper)	-	0	-
Cl. 7(Cr+Ni+Mo)	-	0	-
Cl. 7(Sn)	-	0	-
Cl. 7(V)	-	0	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	0	-
17(Shape, Dimensions and tolerances)	-	0	-
8.1(Tensile Test)	-	0	-
8.1(Hardness Test)	-	0	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	0	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	0	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl. 7(Carbon)	-	0	-
Cl. 7(Sulphur)	-	0	-
Cl. 7(Phosphorous)	-	0	-
Cl. 7(Manganese)	-	0	-
Cl. 7(Silicon)	-	0	-
Cl. 7(Nickel)	-	0	-
Cl. 7(Chromium)	-	0	-
Cl. 7(Aluminium)	-	0	-
Cl. 7(Molybdenum)	-	0	-
Cl. 7(Boron)	-	0	-
Cl. 7(Copper)	-	0	-
Cl. 7(Cr+Ni+Mo)	-	0	-
Cl. 7(Sn)	-	0	-
Cl. 7(V)	-	0	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	0	-
17(Shape, Dimensions and tolerances)	-	0	-
8.1(Tensile Test)	-	0	-
8.1(Hardness Test)	-	0	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	0	-
8.2(Hardenability (only Applicable to Steel Grades of Annexes B and C))	-	0	-
Cl.4.3,7.2 & Table-A.2(Carbon -IS 228 (P-1) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Manganese- IS 228 (P-2) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Phosphorus- IS 228 (P-3) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Sulphur- IS 228 (P-9) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Silicon- IS 228 (P-8) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Copper- IS 228 (P-15) or any other Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Aluminium- Established instrumental/ chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Chromium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Molybdenum- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Nikel- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Tin- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl.4.3,7.2 & Table-A.2(Vanadium- Relevant parts of IS 228 or any other established international instrumental/chemical method)	-	0	-
Cl. 7(Carbon)	-	0	-
Cl. 7(Sulphur)	-	0	-
Cl. 7(Phosphorous)	-	0	-
Cl. 7(Manganese)	-	0	-
Cl. 7(Silicon)	-	0	-
Cl. 7(Nickel)	-	0	-
Cl. 7(Chromium)	-	0	-
Cl. 7(Aluminium)	-	0	-
Cl. 7(Molybdenum)	-	0	-
Cl. 7(Boron)	-	0	-
Cl. 7(Copper)	-	0	-
Cl. 7(Cr+Ni+Mo)	-	0	-
Cl. 7(Sn)	-	0	-
Cl. 7(V)	-	0	-
Cl. 7(Cr+Ni+Cu+Sn+Mo+V)	-	0	-
Cl-10(GRAIN SIZE)	-	0	-
cL-11(carbide spheroidization)	-	0	-
Cl-12.1(Microscopic Inclusions)	-	0	-
Cl-12.2.(Macroscopic Inclusions)	-	0	-
Cl-12.1.1, Table-2(Thin-Worst)	-	0	-
Cl-12.1.1, Table-2(Thin-Mean)	-	0	-
Cl-12.1.1, Table-2(Thick-Worst)	-	0	-
Cl-12.1.1, Table-2(Thick-Mean)	-	0	-
Cl-13.1(Upsetting Test)	-	0	-
Cl-14(SURFACE QUALITY)	-	0	-
Cl-14.1.1(Internal Soundness)	-	0	-
Cl-14.1.4(non-destructive test)	-	0	-
Cl-14.1.3. 1(Non-Destructive Tests i) Eddy Current test ii) Magentic Particle Test)	-	0	-
Cl-14.3(Wire rod)	-	0	-
Cl-14.4(Bars)	-	0	-
Cl-14.5(Bright products)	-	0	-
Cl-15(Decarburization.)	-	0	-
Cl-17.2.1(Tolerances on Bright Bars)	-	0	-
Cl-17.2.2(Length)	-	0	-
clause no.10(GRAIN SIZE- IS 4748)	-	0	-
clause no.12(NON-METALLIC INCLUSIONS)	-	0	-
clause no.14.1.3.1(Eddy Current Test / Magnetic Particle Test)	-	0	-
clause no.14.1.4(INTERNAL SOUNDNESS)	-	0	-

-
Included w.e.f 04.07.2025 Excluding Cl-14.1.3.1 (Non-Destructive Tests i) Eddy Current test ii) Magentic Particle Test)

117

IS 7283 (1992)

Hot - Rolled bars for the production of bright bars and machined parts for engineering applications specification (First Revision)

All Size

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Workmanship)	-	5000	-
Cl 7(Diameter & Out Of Round)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 11(Size)	-	5000	-
Cl 6(Workmanship)	-	5000	-
Cl 7(Diameter & Out Of Round)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 11(Size)	-	5000	-
Cl 6(Workmanship)	-	5000	-
Cl 7(Diameter & Out Of Round)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 11(Size)	-	5000	-
Cl 6(Workmanship)	-	5000	-
Cl 7(Diameter & Out Of Round)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 11(Size)	-	5000	-
Cl 6(Workmanship)	-	5000	-
Cl 7(Diameter & Out Of Round)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 11(Size)	-	5000	-
Cl 6(Workmanship)	-	5000	-
Cl 7(Diameter & Out Of Round)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 11(Size)	-	5000	-
Cl 5(Material Test)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Carbon)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Sulphur)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Phosphorus)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Manganese)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Silicon)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Nickel)	-	5000	-
5, 5.1, 5.2(Copper)	-	5000	-
5, 5.1, 5.2(Chromium)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Lead)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Nitrogen)	-	5000	-
Cl 11(Size)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 7(Diameter & Out Of Round)	-	5000	-
Cl 6(Workmanship)	-	5000	-
11(Grain Size)	-	5000	-
Cl 6(Workmanship)	-	5000	-
7(Diameter & Out Of Round)	-	5000	-
Cl 8(Decarburization)	-	5000	-
Cl 9(Inclusion)	-	5000	-
Cl 10(Hardenability)	-	5000	-
Cl 11(Size)	-	5000	-
5(Material - IS 7283)	-	5000	-
7.3(Dimensional Cutting -IS 7283)	-	5000	-
Cl 5(Material Test)	-	5000	-
5, 5.1, 5.2(Chemical Composition - Carbon)	-	0	-
5, 5.1, 5.2(Chemical Composition - Sulphur)	-	0	-
5, 5.1, 5.2(Chemical Composition - Phosphorus)	-	0	-
5, 5.1, 5.2(Chemical Composition - Manganese)	-	0	-
5, 5.1, 5.2(Chemical Composition - Silicon)	-	0	-
5, 5.1, 5.2(Chemical Composition - Nickel)	-	0	-
5, 5.1, 5.2(Copper)	-	0	-
5, 5.1, 5.2(Chromium)	-	0	-
5, 5.1, 5.2(Chemical Composition - Lead)	-	0	-
5, 5.1, 5.2(Chemical Composition - Nitrogen)	-	0	-
Cl 11(Size)	-	0	-
Cl 10(Hardenability)	-	0	-
Cl 9(Inclusion)	-	0	-
Cl 8(Decarburization)	-	0	-
Cl 7(Diameter & Out Of Round)	-	0	-
Cl 6(Workmanship)	-	0	-
11(Grain Size)	-	0	-
Cl 6(Workmanship)	-	0	-
7(Diameter & Out Of Round)	-	0	-
Cl 8(Decarburization)	-	0	-
Cl 9(Inclusion)	-	0	-
Cl 10(Hardenability)	-	0	-
Cl 11(Size)	-	0	-
5(Material - IS 7283)	-	0	-
7.3(Dimensional Cutting -IS 7283)	-	0	-

-
Included w.e.f 11.07.2025

118

IS 6529 (1996)

Stainless steel blooms, billets and slabs for forging - Specification (First Revision)

9500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7.1,7.2,7.3 Table 1(Carbon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Silicon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Manganese-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Nickel-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Chromium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Molybdenum-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Titanium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Niobium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Sulphur-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Phosphorous-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Others(Nitrogen)-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Selenium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.3(Copper-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
13(Corrosion Resistance- IS 10461(Part1))	-	2000	-
13(Corrosion Resistance- IS 10461(Part2))	-	2000	-
6(Freedom from defects)	-	500	-
9(Hardness)	-	800	-
10(Dimensional Tolerances)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Phosphorus)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Sulphur)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Niobium)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Titanium)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Molybdenum)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Chromium)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Nickel )	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Manganese)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Silicon)	-	300	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Carbon)	-	300	-
7.1,7.2,7.3 Table 1(Carbon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Silicon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Manganese-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Nickel-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Chromium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Molybdenum-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Titanium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	300	-
7.1,7.2,7.3 Table 1(Niobium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	0	-
7.1,7.2,7.3 Table 1(Sulphur-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	0	-
7.1,7.2,7.3 Table 1(Phosphorous-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	0	-
7.1,7.2,7.3 Table 1(Others(Nitrogen)-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	0	-
7.1,7.2,7.3 Table 1(Selenium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	0	-
7.3(Copper-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	0	-
13(Corrosion Resistance- IS 10461(Part1))	-	0	-
13(Corrosion Resistance- IS 10461(Part2))	-	0	-
6(Freedom from defects)	-	0	-
9(Hardness)	-	0	-
10(Dimensional Tolerances)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Phosphorus)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Sulphur)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Niobium)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Titanium)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Molybdenum)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Chromium)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Nickel )	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Manganese)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Silicon)	-	0	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Carbon)	-	0	-
7.1,7.2,7.3 Table 1(Carbon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Silicon-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Manganese-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Nickel-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Chromium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Molybdenum-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Titanium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Niobium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Sulphur-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Phosphorous-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Others(Nitrogen)-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.1,7.2,7.3 Table 1(Selenium-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
7.3(Copper-Relevant parts of IS 228 or any other established instrumental /Chemical method)	-	500	-
13(Corrosion Resistance- IS 10461(Part1))	-	5500	-
13(Corrosion Resistance- IS 10461(Part2))	-	5500	-
6(Freedom from defects)	-	1000	-
9(Hardness)	-	1000	-
10(Dimensional Tolerances)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Phosphorus)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Sulphur)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Niobium)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Titanium)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Molybdenum)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Chromium)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Nickel )	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Manganese)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Silicon)	-	500	-
Clause No.7.1,7.2,7.3 and 12.1 Table 1(Carbon)	-	500	-

-
Included w.e.f 19.05.2025

119

IS 5522 (2014)

Stainless steel sheets and strips for utensils - Specification (Third Revision)

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 7.1 & 7.2 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
Cl. 7.1 & 7.2 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
Cl. 7.1 & 7.2 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
Cl. 7.1 & 7.2 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
Cl. 7.1 & 7.2 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
Cl. 7.1 & 7.2 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
Cl. 7.1 & 7.2 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
Cl. 7.1 & 7.2 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	250	-
8.2, Table 3(Tensile Test-1608:Part 1)	-	1200	-
8.2, Table 3(Proof Stress, N/mm2)	-	1200	-
8.2, Table 3(Tensile Strength, N/mm2)	-	1200	-
8.2, Table 3(Elongation, %)	-	1200	-
8.3(Hardness , max-IS 1500 or IS 1501 (Part 1) or IS 1586)	-	1200	-
8.4(Bend Test)	-	1000	-
8.5(Erichsen Cupping Test)	-	800	-
10.1(Thickness, mm)	-	500	-
10.2(width, mm)	-	500	-
10.3(Length, mm)	-	500	-
10.4(Flatness,mm)	-	500	-
10.5(Camber, mm)	-	500	-
11(Surface Finish)	-	500	-
Cl . 6 .0(Freedom from defect)	-	500	-

-
Included w.e.f 13.05.2025

120

IS 12146 (1987)

Specification for carbon manganese steel forgings for pressure vessels

9000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5.1 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
7(Workmanship & Finish)	-	500	-
8(Freedom from defects)	-	500	-
6 and 9(Mechanical Properties and Test )	-	4500	-
6.1, Table 3 (Tensile Test-1608:Part 1)	-	1000	-
6.1, Table 3 (Yield Strength, Mpa)	-	1000	-
6.1, Table 3 (Tensile Strength, Mpa)	-	1000	-
6.1, Table 3 (Elongation, %)	-	1000	-
6.1, Table 3 (Reduction in area, Percent)	-	500	-
6.1, Table 3 (Impact Test)	-	2500	-
Cl 5.1(Carbon- IS 228(Part 1))	-	300	-
Cl 5.2(Sulphur- IS 228(Part 9))	-	300	-
Cl 5.3(Phosphorous- IS 228(Part 3))	-	300	-
Cl 5.4(Manganese- IS 228(Part 2))	-	300	-
Cl 5.5(Silicon- IS 228(Part 2))	-	300	-
Cl. 5.1 & Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
Cl. 5.1 & Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	300	-
7(Workmanship & Finish)	-	300	-
8(Freedom from defects)	-	300	-
6 and 9(Mechanical Properties and Test )	-	3000	-
6.1, Table 3 (Tensile Test-1608:Part 1)	-	1500	-
6.1, Table 3 (Yield Strength, Mpa)	-	1000	-
6.1, Table 3 (Tensile Strength, Mpa)	-	1000	-
6.1, Table 3 (Elongation, %)	-	800	-
6.1, Table 3 (Reduction in area, Percent)	-	500	-
6.1, Table 3 (Impact Test)	-	2500	-
Cl 5.1(Carbon- IS 228(Part 1))	-	300	-
Cl 5.2(Sulphur- IS 228(Part 9))	-	300	-
Cl 5.3(Phosphorous- IS 228(Part 3))	-	300	-
Cl 5.4(Manganese- IS 228(Part 2))	-	300	-
Cl 5.5(Silicon- IS 228(Part 2))	-	300	-

-
Included w.e.f 13.05.2025 Scope restricted to Grade I & II Ultrasonic testing (optional)

First
Prev
3
4
5
6
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Gravitas Laboratories Private Limited, Greater Noida

Plot No. 95, Udyog Vihar Extn, Ecotech II, Surajpur I.A., Greater Noida, Gautam Buddha Nagar, Uttar Pradesh, 201306

7042049001 testinggravitas@gmail.com

Scope List