BIS - LIMS (Laboratory Information Management System)

DELHI TEST HOUSE, Azadhpur

A-62/3, G T KARNAL ROAD INDUSTRIAL AREA, OPPOSITE HANS CINEMA, AZADPUR, DELHI 110033, Delhi, North, Delhi, 110033

9810442016 info@delhitesthouse.com

Scope List

Reset

200 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

181

IS 14309 (1995)

Blended edible vegetable oils specification

9500 View breakup
Rs.9500.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table-1(Moisture and volatile matter percent by mass, Max type1)	-	750	N.A.
Table-1(Acid value, mx type 1)	-	500	N.A.
Table-1(Unsaponifiable matter, percent by mass, MaX type1)	-	500	N.A.
Table-1(Flash point, Pen&y-Martens type1)	-	400	N.A.

17 Jun, 2027

-
-

182

IS 14542 (1998)

Partly skimmed milk powder specification

4200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Table 1(i)(Moisture Type I (IS 11623))	-	500	-
Table 1(i)(Moisture Type II (IS 11623))	-	500	-
Table 1(ii)(Total solids (milk solids and added salts) Type I (IS 11623))	-	400	-
Table 1(ii)(Total solids (milk solids and added salts) Type II (IS 11623))	-	400	-
Table 1(iii)(Milk fat, Type I (IS I1722))	-	400	-
Table 1(iii)(Milk fat, Type II (IS I1722))	-	400	-
Table 1(iv)(Insolubility index, a) Roller dried Type I (IS 12759))	-	400	-
Table 1(iv)(Insolubility index, a) Roller dried Type II (IS 12759))	-	400	-
Table 1(iv)(Insolubility index, b) Spray dried Type I (IS 12759))	-	400	-
Table 1(iv)(Insolubility index, b) Spray dried Type II (IS 12759))	-	400	-
Table 1(v)(Total ash Type I (Annex B of IS 14433 - Part 1))	-	500	-
Table 1(v)(Total ash Type II (Annex B of IS 14433 - Part 1))	-	500	-
Table 1(vi)(Titratable acidity (as lactic acid) Type I (IS 11766))	-	400	-
Table 1(vi)(Titratable acidity (as lactic acid) Type II (IS 11766))	-	400	-
Cl 6.4(Flavour and Taste (IS 10030))	-	200	-
Cl 6.6.1(Bacterial Count (IS 5402))	-	500	-
Cl 6.6.2(Coliform Count ((IS 5402))	-	500	-

17 Jun, 2027

-
-

183

IS 14735 (1999)

Unplasticized Polyvinyl Chloride (UPVC) Injection Moulded Fittings for Soil and Waste Discharge System for Inside and Outside Buildings Including Ventilation and Rain Water System -

12250 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3(Type of Fitting)	-	100	NA
5(Colour of fittings)	-	250	NA
7.1,Table 1(Wall thickness)	-	100	NA
7.2 ,Table 2&3(Socket Dimensions)	-	100	NA
7.3(Dimensions of waste trap(Nahani Trap)	-	100	NA
8(Sealing Rings)	-	500	NA
10(Workmanship)	-	100	NA
11(Design requirements)	-	100	NA
12.1(Visual appearance)	-	250	NA
12.2(Stress relief test)	-	1500	NA
12.3(Vicat softening tempewrature)	-	1000	NA
Cl.13, IS 12235 (P-7)-2004, (Resistance to Sulphuric Acid)	-	2500	NA
Cl.14, Annex A(Titanium Di-Oxide Content)	-	1000	NA
Cl.15, Annex B(Sulphated Ash Content)	-	1500	NA
16.1(Impact test)	-	1500	NA
17(Watet tightness of joint)	-	1500	NA
19(Marking)	-	100	NA
4(Size Designation)	-	200	-
11.1(Solvent cement type or Rubber ring type)	-	200	-
11.2(Socket and spigot configeration)	-	200	-
11.4,Table 5(Vent cowl)	-	200	-
11.5,Table 6(Pipe Clips)	-	200	-

17 Jun, 2027

-
-

184

IS 1660 (2009)

Wrought aluminium utensils - Specification (First Revision)

7500 View breakup
Rs.7500.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Classification Heavy/Medium/L:ight)	-	100	NA
4(Material)	-	5400	NA
6.1 & Table 1( i) Name of Utensil )	-	100	NA
6.1 & Table 1(ii) Shape of Utensil)	-	100	NA
6.1 & Table 1( Nominal Size, mm)	-	100	NA
6.1 & Table 1(Inside dia, Φ D mm Not declared )	-	100	NA
6.1 & Table 1(Outside dia Ф NA)	-	100	NA
6.1 & Table 1(Height NA)	-	100	NA
6.1 & Table 1(Capacity, l NA)	-	100	NA
6.1( Minimum sheet thickness for nominal size )	-	100	NA
7.1(HANDLES ,When fitted shall be of aluminium, stainless steel or of other suitable fire resistance material These shall be fastened to the utensils by tightly drawn aluminium or stainless steel rivets, by welding, by screwing to cast bosses or by riveting between flange at the end of the handles. Handles shall be so shaped and positioned to facilitate the carrying and handling of the utensils in normal use )	-	150	NA
7.2(Handles shall be sufficiently strong to support a mass in the utensils equivalent to three times the mass of the water capacity of the utensils in the position of normal use without visible permanent deformation of the handle or utensil)	-	150	NA
8.1(The utensils shall be clean reasonably free from distortion, dents, wrinkles, wavy surface, burrs, scratches, pitting and deep tool marks and other surface defects)	-	200	NA
8.2(The design of the utensils shall be such that it is easy to clean and prevent accumulation of dirt)	-	200	NA
8.4.1.2( Finish of the coating: The coating shall be smooth continuous and uniform in appearance, and shall be adherent. It shall be free from powdery areas, loose films and discontinuities, such as breaks and scratches. The size and number of contact marks shall be minimum consistent with good practice.)	-	200	NA
8.4.2(A coating of thickness 25 to 100 microns is generally required)	-	200	NA
8.4.3(Abrasion Resistance When the coating surface is rubbed two or three times with emery paper with emery conforming to grit number 180 using medium finger pressure, it shall not abrade the surface but shall skid over the surface showing not more than a trace of whitening of the surface)	-	200	NA
8.4.4(The colour of the hard anodic coating varies depending upon the alloy, thickness of the coating and electrolye. Normally the colour may vary from dark grey (almost black) to light grey. )	-	200	NA
8.4.5 (When the coated surface is rubbed two or three times with fine emery paper grit number 180 using medium finger pressure, cloth or paper shall not abrade the surface. A faint trace of whitening on the cloth or paper is permissible)	-	200	NA
9(The manufacturer shall provide full instructions for use and cleaning for coated or hard anodized utensils)	-	200	NA
10(Each vessel shall be legibly and indelibly stamped on the outside surface or handle with the manufacturer’s name or registered trade-mark, size and thickness or class. )	-	300	NA

17 Jun, 2027

-
0.0

185

IS 2062 (2011)

Hot rolled medium and high tensile structural steel - Specification (Seventh Revision)

13500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Workmanship)	-	500	For BIS Samples: 1.5 times of BIS testing charges
Cl 10.3(UTM)	-	3000	For BIS Samples: 1.5 times of BIS testing charges
Cl 11.3(Press)	-	500	For BIS Samples: 1.5 times of BIS testing charges
Cl 12(Sudden Load Applied)	-	2800	For BIS Samples: 1.5 times of BIS testing charges
Cl 15(Length, Width & Thickness)	-	500	For BIS Samples: 1.5 times of BIS testing charges
Cl 18(Weight)	-	250	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Carbon Equivalent- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	200	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Nickel- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Chromium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Molybdenum- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5, 8.1 ,8.2. Table 1 (Grade:- E250, E275,E300 ,E350 ,E410, E450, E550,E600, E650)(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 10.3 (Cl. 10.3 (Tensile Strength))	-	1000	For BIS Samples: 1.5 times of BIS testing charges
Cl. 10.3 (Cl. 10.3 (Yield Stress))	-	1000	For BIS Samples: 1.5 times of BIS testing charges
Cl. 10.3 (Cl. 10.3 (Elongation %))	-	1000	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Round Bar: Diameter Maximum)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Round Bar: Diameter Minimum)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Round Bar: Out of Shape)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Square Bar: Side Width: Maximum)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Square Bar: Side Width: Minimum)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Square Bar: Out of Square)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Channel Section: Depth)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Channel Section: Width of Flange)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Channel Section: Flange Out of Square)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Convexity))	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Channel Section: Flatness of Web (Concavity))	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15(Cl. 15 Channel Section: Camber)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl. 15 (Cl. 15 Channel Section: Sweep)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E600, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E650, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E550, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E450, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E410, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E350, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E300, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E275, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Clause - 5, 8.1 & 8.2(E250, ALUMINIUM)	-	400	For BIS Samples: 1.5 times of BIS testing charges

17 Jun, 2027

-
Cl 13 (Y Groove Cracking Test)

186

IS 1239 : Part 1 (2004)

Steel tubes, tubulars and other wrought steel fittings - Specification: Part 1 steel tubes (Sixth Revision)

9000 View breakup
Rs.9000.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(Outer Diameter, Thickness & Mass)	-	1500	NA
Cl 10.1(Manufacturing )	-	500	NA
Cl 10.1.1(Manufacturing )	-	500	NA
Cl 12(Workmanship)	-	500	NA
Cl 14(Tensile Test, Flattening Test & Bend Test)	-	3500	NA
Cl 15(Workmanship)	-	500	NA

17 Jun, 2027

-
0.0

187

IS 1079 (2017)

Hot rolled carbon steel sheet, plate and strip - Specification (Seventh Revision)

9500 View breakup
Rs.9500.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	400	NA
6.1(Manganese %)	-	400	NA
6.1(Sulphur %)	-	400	NA
6.1(Phosphorus %)	-	400	NA
6.1(V)	-	400	NA
6.1( Nb)	-	400	NA
6.1( Copper %)	-	400	NA
6.1( Nitrogen%)	-	1000	NA
6.1(Silicon %)	-	400	NA
6.1( Aluminium %)	-	400	NA
6.1( Ti)	-	400	NA
6.1(Cr)	-	400	NA
6.1(Mo)	-	400	NA
6.1(Ni)	-	400	NA
Cl 8(UTM)	-	2000	NA
Cl 9(Press)	-	500	NA
Cl 10(Die Press)	-	1000	NA
Cl 12(Workmanship)	-	300	NA
Cl 13(Length, Width & Thickness)	-	400	NA

17 Jun, 2027

-
0.0

188

IS 733 (1983)

Specification for wrought aluminium and aluminium alloy bars, rods and sections (For General Engineering Purposes) (Third Revision)

7000 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others:Rs.7000.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 4(Freedom from Defects)	-	200	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5.1, Table 2(0.2 Percent proof stress- IS 1816)	-	600	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5.1, Table 2(Tensile Strength- IS 1816)	-	800	For BIS Samples: 1.5 times of BIS testing charges
Cl. 5.1, Table 2(Elongation on 50 mm or 5.65√So Gauge Length)	-	600	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Aluminium- IS 504 or by any other suitable instrumental method)	-	200	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Magnesium- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Silicon- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Iron- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Zinc- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Titanium and / or other grain refining elements - IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Chromium- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Copper- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Ti+ V- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Cr+ Mn- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges
Cl. 0.4, 5.1, Table 1(Total Impurities- IS 504 or by any other suitable instrumental method)	-	400	For BIS Samples: 1.5 times of BIS testing charges

17 Jun, 2027

-
0.0

189

IS 11513 (2017)

Hot rolled carbon steel strip for cold rolling purposes - Specification (Second Revision)

5250 View breakup
Rs.5250.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1(Carbon %)	-	250	NA
6.1(Manganese %)	-	250	NA
6.1(Sulphur %)	-	250	NA
6.1(Phosphorus %)	-	250	NA
6.1( Nitrogen%)	-	1000	NA
6.1(Silicon %)	-	250	NA
6.1( Aluminium %)	-	250	NA
6.1(V)	-	250	NA
6.1( Ti)	-	250	NA
6.1( Copper %)	-	250	NA
6.1( Nb)	-	250	NA
6.1(Boron)	-	250	NA
Cl 8(Workmanship)	-	500	NA
Cl 9(Length, Width, Thickness, Crown, Edge Camber & Difference in Thickness Across Width )	-	500	NA

17 Jun, 2027

-
0.0

190

IS 432 : Part 2 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 2 Hard-Drawn Steel Wire

8887.50 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 3.1.1(Sulphur)	-	500	NA
Clause 3.1.1(Phosphorus)	-	500	NA
Cl 4.1(Workmanship)	-	500	NA
Cl 5 & 6(Diameter)	-	1000	NA
Cl 7(UTM)	-	3000	NA
Cl 8.3(Bending To Both Side At 90°, Then Straight)	-	500	NA

17 Jun, 2027

-
0.0

191

IS 432 : Part 1 (1982)

Mild Steel and Medium Tensile Steel Bars and Hard-Drawn Steel Wire for Concrete Reinforcement: Part 1 Mild Steel and Medium Tensile Steel Bars

7000 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5.1(Workmanship)	-	200	For BIS samples: 1.5 times of BIS testing charges
Cl 6.1(Diameter)	-	200	For BIS samples: 1.5 times of BIS testing charges.
Cl 6.2(Diameter & Ovality)	-	200	For BIS samples: 1.5 times of BIS testing charges.
Cl 6.2(Weight)	-	100	For BIS samples: 1.5 times of BIS testing charges.
Cl 8.1(ultimate tensile stress, yield stress and percentage elongation)	-	1800	For BIS samples: 1.5 times of BIS testing charges.
Cl 9.3(Press)	-	400	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1( CARBON)	-	350	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(SULPHUR)	-	350	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(PHOSPHURS)	-	350	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(MANGANESE)	-	350	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(NITROGEN)	-	1000	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(SILICON)	-	350	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1( ALUMINIUM)	-	250	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(Nickel)	-	250	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(Chromium)	-	250	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(Molybdenum)	-	250	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.1(NIOBIUM)	-	250	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.2(VANADIUM)	-	250	For BIS samples: 1.5 times of BIS testing charges.
Clause -4, 4.3(TITANIUM)	-	250	For BIS samples: 1.5 times of BIS testing charges.
Cl 5.1(Workmanship)	-	200	For BIS samples: 1.5 times of BIS testing charges.
Cl 6.2(Diameter & Ovality)	-	400	For BIS samples: 1.5 times of BIS testing charges.
Cl 6.2(Weight)	-	100	For BIS samples: 1.5 times of BIS testing charges.
Cl 8(Physical Requirements)	-	1800	For BIS samples: 1.5 times of BIS testing charges.
Cl 9.3(Press)	-	400	For BIS samples: 1.5 times of BIS testing charges.

17 Jun, 2027

-
-

192

IS 14724 (1999)

Water purifiers with Ultra - Violet disinfection - Specification

19500 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others:Rs.19500.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3(Workmanship)	-	100	For BIS Samples: 1.5 times of BIS testing charges
Cl 5(Power Supply, Maximum Rate of Flow, Electrical Safety, Materials of Construction, Safety Against UV Exposure, Indicating Lights & In-Bullt Protections and Ease of Operation)	-	3000	For BIS Samples: 1.5 times of BIS testing charges
Cl 6(Leakage-Tightness & Verification of Guarantees of Performance)	-	4000	For BIS Samples: 1.5 times of BIS testing charges
6.2.2.1(Test for turbidity (IS 3025 Part 10))	-	1000	For BIS Samples: 1.5 times of BIS testing charges
6.2.2.2(Test for supended particles)	-	500	For BIS Samples: 1.5 times of BIS testing charges
6.2.2.4(Test for adsorption of activated carbon (IS 3025 Part 5))	-	3000	For BIS Samples: 1.5 times of BIS testing charges
6.2.2.3(Test for Microbiology - Annex A)	-	8000	For BIS Samples: 1.5 times of BIS testing charges

17 Jun, 2027

-
0.0

193

IS 3975 (1999)

Low carbon galvanized steel wires, formed wires and tapes for armouring of cables - Specification (Third Revision)

5200 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Clause 6.1, Table-1(Sulphur)	-	250	NA
Clause 6.1, Table-1(Phosphorus)	-	250	NA
6.2(Phosphorus %)	-	250	NA
6.2(Sulphur %)	-	250	NA
6.2( Nitrogen%)	-	1000	NA
7(Dimensions)	-	200	NA
8.1(Mechanical Properties (as per table 5 of IS 1608))	-	700	NA
8.2(Mechanical Properties (as per IS 1717))	-	400	NA
8.3(Mechanical Properties (as per IS 1755))	-	400	NA
8.4(Mechanical Properties (as per IS 10810(Part- 42)))	-	400	NA
9.1(Galvanizing Requirements )	-	500	NA
9.2(Galvanizing Requirements )	-	500	NA
9.3(Galvanizing Requirements )	-	400	NA
11(Freedom from defects)	-	200	NA

17 Jun, 2027

-
-

194

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1, 8.1.1 & 10.1 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	NA
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1000	NA
6(Freedom From Defects)	-	200	NA
9.3(Tensile Test-1608:Part 1)	-	900	NA
9.3, Table 3 (Yield Strength, Mpa)	-	800	NA
9.3, Table 3 (Elongation, %)	-	800	NA
11(Surface finish)	-	300	NA
14.1(Thickness,mm)	-	200	NA
14.2( Width, mm)	-	200	NA
14.3(Length, mm)	-	200	NA
14.5(Camber, mm)	-	200	NA
14.4(Flatness, mm)	-	200	NA

17 Jun, 2027

-
-

195

IS 7809 : Part 3 : Sec 1 (1986)

Specification for pressure sensitive adhesive insulating tapes for electrical purposes: Part 3 requirements or individual materials: Sec 1 plasticized polyvinylchloride tapes with non - Thermosetting adhesive (First Revision)

19400 View breakup
Rs.19400.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(Marking, Cl.9 of IS 7809 (Part 1):1975)	-	100	NA
2.1.1(Type and Desiganation)	-	100	NA
2.1.2(Type and Desiganation)	-	100	NA
3.1(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	100	NA
3.2(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	300	NA
3.3(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	300	NA
3.4(General Requirments,as per IS 7809 (Part 1 ) :1975 )	-	300	NA
4.1(Performance Requirments)	-	700	NA
4.2(Performance Requirments)	-	700	NA
4.3(Performance Requirments)	-	700	NA
4.4(Performance Requirments)	-	1800	NA
4.5(Performance Requirments)	-	1700	NA
4.6(Flammability ,Cl 6 of IS 7809 (Part 2): 1977)	-	500	NA
4.7(Electrolytic corrosion)	-	1500	NA
4.8(Stability to accelerated ageing )	-	1000	NA
4.9(Insulation resistance test)	-	500	NA
3.1( Minimum Storage Life Cl. 7.1 of IS 7809(Part 1) :1975)	-	9100	NA

17 Jun, 2027

-
Up to 0.22mm thickness only

196

IS 15622 (2017)

Pressed Ceramic Tiles - Specification (First Revision)

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5& 5.1, Table 1(Coordinating size- IS 13630(pt-1))	-	0	Provisional Testing Charges
5& 5.1, Table 1(Work size- IS 13630(pt-1))	-	0	Provisional Testing Charges
5& 5.1, Table 1(Thickness- IS 13630(pt-1))	-	200	Provisional Testing Charges
5& 5.1, Table 2(Nominal size -IS 13630(pt-1))	-	0	Provisional Testing Charges
5& 5.1, Table 2(Thickness- IS 13630(pt-1))	-	200	Provisional Testing Charges
5& 5.1, Table 3(Coordinating size- IS 13630(pt-1))	-	0	Provisional Testing Charges
5& 5.1, Table 3(Work size-IS 13630(pt-1))	-	0	Provisional Testing Charges
5& 5.1, Table 3(Thickness- IS 13630(pt-1))	-	200	Provisional Testing Charges
5& 5.1, Table 4(Nominal size-IS 13630(pt-1))	-	0	Provisional Testing Charges
5& 5.1, Table 4(Work size-IS 13630(pt-1))	-	0	Provisional Testing Charges
5& 5.1, Table 4(Thickness- IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 5, i a (Length-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 5,i a (width-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 5, i b (Thickness- IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 5, i c(Straigthness of side-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 5, i d(Rectangularity-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 5, i e(Surface flatness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 5, i f(Surface quality-IS 13630(pt-1))	-	300	Provisional Testing Charges
6 table 5, ii a(Water Absorption-IS 13630(pt-2))	-	1000	Provisional Testing Charges
6 table 5, ii b(Module of rupture -IS 13630(pt-6))	-	800	Provisional Testing Charges
6 table 5, ii c(Bending Strength-IS 13630(pt-6))	-	700	Provisional Testing Charges
6 table 5, ii d(Moisture Expension-IS 13630(pt-3))	-	400	Provisional Testing Charges
6 table 5, ii e(Scratch hardness of surface -IS 13630(pt-13))	-	500	Provisional Testing Charges
6 table 5, ii f(Coefficient of linear tharmal expansion from ambient temperature to100°C-IS 13630(pt-4) )	-	500	Provisional Testing Charges
6 table 5, ii g(Thermal shock resistance IS 13630(pt-5))	-	500	Provisional Testing Charges
6 table 5, ii h(Impact resistance-IS 13630(pt-14))	-	1000	Provisional Testing Charges
6 table 5, ii k(Crazing resistance-IS 13630(pt-9))	-	2000	Provisional Testing Charges
6 table 5, ii m(resistance to surface abrasion of glazed Tilles)	-	1000	Provisional Testing Charges
6 table 5, iii a(Resistance to staining of glazed Tilles-IS 13630(pt-8))	-	500	Provisional Testing Charges
6 table 5, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound-IS 13630(pt-8))	-	1150	Provisional Testing Charges
6 table 5, iii c(Resistance to acid and alkalis (with the exception ofhydrofluoric acid and its compounds – Glazed tiles-IS 13630(pt-8))	-	1150	Provisional Testing Charges
6 table 6, i a (Length-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 6, i a (width-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 6, i b (Thickness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 6, i c(Straigthness of side-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 6, i d(Rectangularity-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 6, i e(Surface flatness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 6, i f(Surface quality-IS 13630(pt-1))	-	300	Provisional Testing Charges
6 table 6, ii a(Water Absorption-IS 13630(pt-2) )	-	1000	Provisional Testing Charges
6 table 6, ii b(Module of rupture -IS 13630(pt-6))	-	800	Provisional Testing Charges
6 table 6, ii c(Bending Strength-IS 13630(pt-6))	-	700	Provisional Testing Charges
6 table 6, ii d(Moisture Expension-IS 13630(pt-3))	-	400	Provisional Testing Charges
6 table 6, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	500	Provisional Testing Charges
5 table 6, ii f(Resistance to surface abrasion of glazed Tilles)	-	1000	Provisional Testing Charges
6 table 6, ii g(Coefficient of linear tharmal expansion from ambient temperature to100°C-IS13630(pt-4) )	-	500	Provisional Testing Charges
6 table 6, ii h(Thermal shock resistance-IS13630(pt-5) )	-	500	Provisional Testing Charges
6 table 6, ii j(Crazing resistance-IS 13630(pt-9))	-	2000	Provisional Testing Charges
6 table 6, ii k(Impact resistance-IS 13630(pt-14))	-	1000	Provisional Testing Charges
6 table 6, ii n(Forst resistance-IS 13630(pt-10))	-	5000	Provisional Testing Charges
6 table 6, ii p(Resistance to deep abrasion of unglazed tiles)	-	1000	Provisional Testing Charges
6 table 6, iii a(Resistance to staining of glazed Tilles)	-	500	Provisional Testing Charges
6 table 6, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1150	Provisional Testing Charges
6 table 6, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1150	Provisional Testing Charges
6 table 7, i a (Length-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 7, i a (width-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 7, i b (Thickness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 7, i c(Straigthness of side-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 7, i d(Rectangularity-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 7, i e(Surface flatness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 7, i f(Surface quality-IS 13630(pt-1))	-	300	Provisional Testing Charges
6 table 7, ii a(Water Absorption-IS 13630(pt-2) )	-	1000	Provisional Testing Charges
6 table 7, ii b(Module of rupture-IS 13630(pt-6) )	-	800	Provisional Testing Charges
6 table 7, ii c(Bending Strength-IS 13630(pt-6))	-	700	Provisional Testing Charges
6 table 7, ii d(Moisture Expension-IS 13630(pt-3))	-	400	Provisional Testing Charges
6 table 7, ii e(Scratch hardness of surface-IS 13630(pt-13))	-	500	Provisional Testing Charges
6 table 7, ii f(Resistance to surface abrasion of glazed Tilles)	-	1000	Provisional Testing Charges
6 table 7, ii g(Coefficient of linear tharmal expansion from ambient temperature to100°C-IS13630(pt-4) )	-	500	Provisional Testing Charges
6 table 7, ii h(Thermal shock resistance-IS13630(pt-5) )	-	500	Provisional Testing Charges
6 table 7, ii j(Crazing resistance-IS 13630(pt-9))	-	2000	Provisional Testing Charges
6 table 7, ii k(Impact resistance-IS 13630(pt-14))	-	1000	Provisional Testing Charges
6 table 7, ii n(Forst resistance-IS 13630(pt-10))	-	5000	Provisional Testing Charges
6 table 7, ii p(Resistance to deep abrasion of unglazed tiles)	-	1000	Provisional Testing Charges
6 table 7, iii a(Resistance to staining of glazed Tilles)	-	500	Provisional Testing Charges
6 table 7, iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1150	Provisional Testing Charges
6 table 7, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1150	Provisional Testing Charges
6 table 8, i a (Length-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 8, i a (width-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 8, i b (Thickness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 8, i c(Straigthness of side-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 8, i d(Rectangularity-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 8, i e(Surface flatness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 8, i f(Surface quality-IS 13630(pt-1))	-	300	Provisional Testing Charges
6 table 8, ii a(Water Absorption-IS 13630(pt-6) )	-	1000	Provisional Testing Charges
6 table 8, ii b(Module of rupture-IS 13630(pt-6) )	-	1150	Provisional Testing Charges
6 table 8, ii c(Bending Strength-IS 13630(pt-6))	-	1150	Provisional Testing Charges
6 table 8, ii d(Moisture Expension-IS 13630(pt-3))	-	400	Provisional Testing Charges
6 table 8, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	500	Provisional Testing Charges
6 table 8, ii f(Resistance to surface abrasion of glazed Tilles)	-	1000	Provisional Testing Charges
6 table 8, ii g(Coefficient of linear tharmal expansion from ambient temperature to100°C-IS 13630(pt-4) )	-	500	Provisional Testing Charges
6 table 8, ii h(Thermal shock resistance-IS 13630(pt-5) )	-	500	Provisional Testing Charges
6 table 9, ii j(Crazing resistance-IS 13630(pt-9))	-	2000	Provisional Testing Charges
6 table 8, ii k(Impact resistance-IS 13630(pt-14))	-	1000	Provisional Testing Charges
6 table 8, ii n(Forst resistance-IS 13630(pt-10))	-	5000	Provisional Testing Charges
6 table 8, ii p(Resistance to deep abrasion of unglazed tiles)	-	1000	Provisional Testing Charges
6 table 8, ii q(Bulk Density-IS13630(pt-2))	-	500	Provisional Testing Charges
6 table 8, iii a(Resistance to staining of glazed Tilles)	-	500	Provisional Testing Charges
6 table 8 iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1150	Provisional Testing Charges
6 table 8, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1150	Provisional Testing Charges
6 table 9, i a (Length-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 9, i a (width-IS 13630(pt-1))	-	100	Provisional Testing Charges
6 table 9, i b (Thickness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 9, i c(Straigthness of side-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 9, i d(Rectangularity-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 9, i e(Surface flatness-IS 13630(pt-1))	-	200	Provisional Testing Charges
6 table 9, i f(Surface quality-IS 13630(pt-1))	-	300	Provisional Testing Charges
6 table 9, ii a(Water Absorption-IS 13630(pt-6) )	-	1000	Provisional Testing Charges
6 table 9, ii b(Module of rupture-IS 13630(pt-6) )	-	800	Provisional Testing Charges
6 table 9, ii c(Bending Strength-IS 13630(pt-6))	-	700	Provisional Testing Charges
6 table 9, ii d(Moisture Expension-IS 13630(pt-3))	-	400	Provisional Testing Charges
6 table 9, ii e(Scratch hardness of surface-IS 13630(pt-13) )	-	500	Provisional Testing Charges
6 table 9, ii f(Resistance to surface abrasion of glazed Tilles)	-	1000	Provisional Testing Charges
6 table 9, ii g(Coefficient of linear tharmal expansion from ambient temperature to100°C )	-	500	Provisional Testing Charges
6 table 9, ii h(Thermal shock resistance-IS 13630(pt-5))	-	500	Provisional Testing Charges
6 table 9, ii k(Impact resistance-IS 13630(pt-14))	-	1000	Provisional Testing Charges
6 table 9, ii n(Forst resistance-IS 13630(pt-10))	-	5000	Provisional Testing Charges
6 table 9, ii p(Resistance to deep abrasion of unglazed tiles)	-	1000	Provisional Testing Charges
6 table 9, ii q(Bulk Density-)	-	500	Provisional Testing Charges
6 table 9, iii a(Resistance to staining )	-	500	Provisional Testing Charges
6 table 9 iii b(Resistance to household chemicals and swimming pool water cleansers agents containing hydrofluoric acid and its compound)	-	1150	Provisional Testing Charges
6 table 9, iii c(Resistance to acid and alkalis (with the exception of hydrofluoric acid and its compounds – Glazed tiles)	-	1150	Provisional Testing Charges

17 Jun, 2027

-
-

197

IS 1489 : Part 2 (2015)

Portland - Pozzolana cement - Specification: Part 2 calcined clay based

10000 View breakup
Rs.10000.00

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	NA
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	300	NA
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	NA
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	NA
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	300	NA
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	300	NA
7 -Table 2- i(Fineness 4031 Part 2)	-	700	NA
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	600	NA
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	600	NA
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	NA
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	NA
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	NA
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	NA
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	NA
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	2000	NA
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1200	NA
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	N.A.
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	300	N.A.
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	N.A.
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	N.A.
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	300	N.A.
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	300	N.A.
7 -Table 2- i(Fineness 4031 Part 2)	-	700	N.A.
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	600	N.A.
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	600	N.A.
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	N.A.
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	N.A.
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	N.A.
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	N.A.
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	N.A.
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	2000	N.A.
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1200	N.A.

17 Jun, 2027

-
Exclusion: 4 (Raw material)

198

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	NA
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	300	NA
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	NA
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	NA
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	300	NA
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	300	NA
7 -Table 2- i(Fineness 4031 Part 2)	-	700	NA
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	600	NA
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	600	NA
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	NA
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	NA
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	NA
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	NA
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	NA
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	2000	NA
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1200	NA
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	500	N.A.
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	300	N.A.
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	500	N.A.
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	500	N.A.
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	300	N.A.
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	300	N.A.
7 -Table 2- i(Fineness 4031 Part 2)	-	700	N.A.
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	600	N.A.
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	600	N.A.
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	500	N.A.
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	500	N.A.
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	500	N.A.
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	500	N.A.
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	500	N.A.
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	2000	N.A.
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1200	N.A.

17 Jun, 2027

-
-

199

IS 269 (2015)

Ordinary portland cement - Specification (Sixth Revision)

33, 43, 43S, 53 & 53S

9500 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
6.1 Table-2 iii.(Insoluble residue)	-	500	N.A.
6.1 Table-2 vii(Chloride content)	-	300	N.A.
6.1 Table-2 vi(Loss on ignition)	-	500	N.A.
6.1 Table-2 viii(Alkali content)	-	500	N.A.
7 Table-3 i.(Fineness)	-	700	N.A.
7 Table-3 ii a(Expansion by Le Chatelier)	-	600	N.A.
7 Table-3 ii b(Expansion by Autoclave)	-	600	N.A.
7 Table-3 iii a(Setting Time Initial)	-	400	N.A.
7 Table-3 iii b(Setting Time Final)	-	400	N.A.
7 Table-3 iv a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	700	N.A.
7 Table-3 iv b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	650	N.A.
7 Table-3 iv c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	650	N.A.
7 Table-3 v(Transverse Strength - IS 4031 Part 8 (Optional))	-	1200	N.A.

17 Jun, 2027

-
Included w.e.f. 28-09-2018

200

IS 383 (2016)

Coarse and Fine Aggregate for Concrete - Specification (Third Revision)

17400 View breakup
For BIS samples: 1.5 times of BIS testing charges, For others

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4.1 (a)(mechanical properties- Aggregate Crushing Value/Ten Percent Fines Value)	-	1300	For BIS samples 1.5 times of BIS testing charges
5.4.2(a)( Aggregates Impact Value)	-	700	For BIS samples 1.5 times of BIS testing charges
5.4.3(a)( Aggregate Abrasion Value)	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(i)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 80 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(ii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 63 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(iii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 40 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(iv)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 20 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(v)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 16 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(vi)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 12.5 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(vii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 10 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(viii)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 4.75 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.1-Table 7(ix)(SIZE AND GRADING OF AGGREGATES-Single-Sized Coarse Aggregates-Percentage Passing through 2.36 mm sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.3-Table 9(iv)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 1.18mm Sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.3-Table 9(v)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 600µm Sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.3-Table 9(vi)(SIZE AND GRADING OF AGGREGATES-Fine Aggregate-Percentage Passing through 300µm Sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges
6.4-Table 10(vi)(SIZE AND GRADING OF AGGREGATES- All-in-Aggregate Grading-Percentage Passing through 150µm Sieve )	-	1000	For BIS samples 1.5 times of BIS testing charges

17 Jun, 2027

-
Only for aggregates from natural sources

Bureau of Indian Standards

The National Standards Body of India

DELHI TEST HOUSE, Azadhpur

A-62/3, G T KARNAL ROAD INDUSTRIAL AREA, OPPOSITE HANS CINEMA, AZADPUR, DELHI 110033, Delhi, North, Delhi, 110033

9810442016 info@delhitesthouse.com

Scope List