BIS - LIMS (Laboratory Information Management System)

Kailtech Test and Research Centre Pvt. Ltd., Indore

141C, Electronic Complex Industrial Area, Indore, Indore, Madhya Pradesh, 452010

- contact@kailtech.net

Scope List

Reset

125 Results

S.No.

Indian Standard No.

Product

Grade / Type / Size / Designation etc.

Testing Charges (Excl. Of Taxes)

Validity Date

Remark

IS 1489 (Part 1) (2015)

Portland pozzolana cement - Specification: Part 1 fly Ash Based

All

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7 -Table 2- vi(Drying Shrinkage- IS 4031 Part 10)	-	5000	Drying Shrinkage
7 -Table 2- v(Transverse Strength - IS 4031 Part 8 (Optional))	-	5000	Transverse Strength
7 -Table 2- iv- c(Compressive Strength At 672 hrs ± 4 hr - IS 4031 Part 6)	-	3000	Compressive Strength
7 -Table 2- iv- b(Compressive Strength At 168 hrs ± 2 hr - IS 4031 Part 6)	-	3000	Compressive Strength
7 -Table 2- iv- a(Compressive Strength At 72 hrs ± 1 hr - IS 4031 Part 6)	-	3000	Compressive Strength
7 -Table 2-iii- b(Setting Time Final- 4031 Part 5)	-	2000	Setting Time (Initial & Final)
7 -Table 2- iii- a(Setting Time Initial- 4031 Part 5)	-	2000	Setting Time (Initial & Final)
7 -Table 2- ii- b(Expansion by Autoclave- 4031 Part 3)	-	2000	Soundness by Autoclave
7 -Table 2- ii- a(Expansion by Le Chatelier- 4031 Part 3)	-	1000	Soundness by Le-Chatelier
7 -Table 2- i(Fineness 4031 Part 2)	-	1000	Fineness by Blain Air Permeability
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	2000	Alkali Content
6 - Table - 1 v(Chloride content - Cl 4.13 of IS 4032:1985)	-	1500	Chloride Content
6 - Table - 1 iv(Loss on ignition - Cl 7.1 of IS 4032:1985)	-	1500	Loss of Ignition
6 - Table - 1 iii(Total Sulphur Content calculated as Sulphuric Anhydride (SO3) - Cl 7.3 of IS 4032:1985)	-	1000	Total Sulphur Content
6 - Table - 1 ii(Magnesia - Cl 7.2 of IS 4032:1985)	-	1000	Magnesia
6 - Table - 1 i(Insoluble residue - Cl 7.4 of IS 4032:1985)	-	1000	Insoluble residue
6 - Table - 1 vi( Alkali content as (Na2O + 0.658 K2O) - Cl 4.11 of IS 4032:1985)	-	2000	Alkali Content
Clause 7 Table 2 SI No. (v) (Transverse Strength, 672 ± 4 h)	-	4000	Transverse Strength,
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 672 ± 4 h)	-	4000	Transverse Strength,
Clause 7Table 2 SI No. (v)(Transverse Strength, 168 ± 2 h)	-	4000	Transverse Strength,
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 168 ± 2 h)	-	4000	Transverse Strength,
Clause 7Table 2 SI No. (v)(Transverse Strength, 72 ± 1 h)	-	4000	Transverse Strength,
Clause 7 Table 2 SI No. (v) (Compressive strength of Transverse Specimen, 72 ± 1 h)	-	4000	Transverse Strength,

18 Dec, 2027

-
-

IS 513 : Part 1 (2016)

Cold reduced carbon steel sheet and strip: Part 1 cold forming and drawing purpose (Sixth Revision)

All

16000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Chemical Composition)	-	15000	Chemical Composition (All Parameters)
Cl 8(UTM)	-	5000	Tensile
Cl 9(Workmanship)	-	2000	Surface Finish
Cl 9.6(Workmanship)	-	500	Oiling Visual
Cl 10(Workmanship)	-	500	Freedom from Defects
Cl 11(Length, Width & Thickness)	-	500	Dimensions
Cl 8(UTM)	-	5000	Tensile
Cl 9.5(Workmanship)	-	2000	Surface Finish
Cl. 8.1 & Table 5A, 5B & 5C(Yield Stress)	-	5000	Yield Stress
Cl. 9 Table 8(Surface roughness)	-	2000	Surface Roughness
Cl. 11(Out of square)	-	500	Dimension
Cl. 11(Flatness)	-	500	Dimension
Cl. 11(Camber)	-	500	Dimension
Cl. 11(Width)	-	500	Dimension
Cl. 11(Thickness)	-	500	Dimension
Cl. 8.7(Bake Hardening Index)	-	2000	Bake Hardening
Cl. 8.6 Table 5A, 5B & 5C(Tensile Strain Hardening Component (n-Value))	-	2000	Tensile Strain Hardening
Cl. 8.5 Table 5A, 5B & 5C(Plastic Strain Ratio (r bar/r-90))	-	1000	Plastic Strain Ratio
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 50 mm gauge length)	-	5000	Elongation
Cl. 8.1 & Table 5A, 5B & 5C(Elongation at 80 mm gauge length)	-	5000	Elongation
Cl. 8.2(Cupping Test(Only for sheet and coils CR2, CR3, CR4(having thickness 0.5 mm-2.0 mm))	-	1500	Cupping Test
Cl. 8.4(Bend Test)	-	1000	Bend Test
Cl. 8.3 Table 6(Hardness Test ( Only for CR0 & CR1))	-	1000	Hardness Test

18 Dec, 2027

-
-

IS 4984 (2016)

Polyethylene pipes for water supply - Specification (Fifth Revision)

Up to 315

3500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5, 5.1 table-1(MATERIALS)	-	0	This is not a test
5.2(Polyethylene Resin)	-	5000	All Tests of Table 2
5.3(c)(Carbon Black Master Batch)	-	1500	ok
5.3(d)(Carbon Black Master Batch)	-	1500	Ash Content
8.3(Carbon black)	-	1500	CBC
8.6(Overall migration)	-	5000	ok
6, 6.1(PIPE DESCRIPTION)	-	0	Not a Test
6, 6.1.1(PIPE DESCRIPTION)	-	0	No Clause available in IS 4984 : 2016
6.2(Colour)	-	500	ok
6.2.1(6.1.1 Identification Stripes)	-	1000	ok
7.2(Length)	-	500	ok
Cl-7.4(Mean Outside Diameter (For upto 50 mm take 8 reading, above 50mm take 6 reading & average will be reported))	-	1000	ok
7.4.1.2(Ovality)	-	500	ok
8,/8.1/8.1.1 table-5(PERFORMANCE REQUIREMENTS / Hydraulic Characteristics/ Internal Pressure Creep Rupture Test of Pipe)	-	10000	ok
8.1.2 table -5(Internal Pressure Creep Rupture Test of Pipe Joints)	-	2000	ok
8.2(Longitudinal Reversion Test)	-	2000	ok
8.4( Melt Flow Rate)	-	1500	ok
8.5 (Oxidation Induction Time)	-	10000	ok
8.7(Density)	-	1000	ok
8.8(Tensile Strength for Butt-fusion)	-	10000	ok
8.9 table-6(Elongation at Break)	-	2000	ok
8.10(Slow Crack Growth Rate)	-	10000	ok

18 Dec, 2027

-
-

IS 456 (2000)

Plain and reinforced concrete - Code of practice (Fourth Revision)

4000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.4-Table-1 (v)-IS: 3025(P-17)(Suspended matter)	-	750	-
5.4-Table-1 (iv)-IS: 3025(P-32)(Chloride)	-	1000	-
5.4-Table-1 (ii)-IS: 3025(P-24)(Sulphate)	-	750	-
5.4-Table-1 (i)-IS: 3025(P-18)(In-Organic)	-	750	-
5.4-Table-1 (i)-IS: 3025(P-18)(Organic )	-	750	-
5.4.2-IS: 3025(P-11)(Ph)	-	750	-
5.4-(b)-IS: 3025 (P-23)(Volume of 0.02 N H2SO4 to neutralized 100 ml of water using mixed indicator)	-	750	-
5.4-(a)-IS: 3025 (P-22)(Volume of 0.02 N NaOH to neutralized 100 ml of water using phenolphthalein indicator)	-	750	-
16.1(Average Compressive Strength)	-	1500	-

18 Dec, 2027

-
-

IS 12592 (2002)

Precast concrete manhole cover and frame - Specification (First Revision)

All

14821 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(General)	-	3000	General
3(Type/Shape of Cover)	-	3000	General
8(LIFTING HOOKS)	-	7500	Dimension
5.2 and Table 1(Dimensions of Frame - A)	-	7500	Dimension
5.2 and Table 1(Dimensions of Frame - B)	-	7500	Dimension
5.2 and Table 1(Dimensions of Frame - C)	-	7500	Dimension
5.2 and Table 1(Dimensions of Frame - D)	-	7500	Dimension
5.2 and Table 1(Dimensions of Frame - E)	-	7500	Dimension
5.2 and Table 1(Dimensions of Frame - F)	-	7500	Dimension
5.2(Dimensions of cover- Diameter)	-	7500	Dimension
5.2(Clearance at top between the frame and the cover all round the periphery)	-	7500	Dimension
5.2(Top surface ofthe frame and cover is in level)	-	7500	Dimension
5.2(Suitable taper matching with taper given for the frame shall be provided to the periphery of the cover)	-	7500	Dimension
5.2 and Fig 1(Clear cover to reinforcement)	-	7500	Dimension
5.2 and Fig 1(Distance of housing from the edge)	-	7500	Dimension
7.4.1(Edge Protection and Finishing - Frame)	-	7500	Dimension
7.4.2(Edge Protection and Finishing - Cover)	-	7500	Dimension
9.3 and Table and Annex C(Load Test)	-	10000	Load Test
Clause No. 6(Design)	-	7500	Dimension
Clause No. 7.4.1(Edge protection and finishing of frame (Size of mild steel flat))	-	7500	Dimension
Clause No. 7.4.1(Edge protection and finishing of frame (Steel connectors))	-	7500	Dimension
Clause No. 7.4.2(Edge protection and finishing of cover (Cover finish of top surface))	-	7500	Dimension
Clause No. 7.4.2(Edge protection and finishing of cover (Thikness of MS sheet))	-	7500	Dimension
Clause No. 7.4.4(Compatitbilty of Seating of cover and frame)	-	7500	Dimension
Clause No. 8(Lifting Hooks (Diameter of MS rod))	-	7500	Dimension
Clause No. 8(Lifting Device)	-	7500	Dimension
Clause No. 9.3, 12.3 & C-1.1, Table No. 2(Test Load)	-	10000	Load Test
Clause No. 9.3, 12.3 & C-1.1, Table No. 2(2/3rd of Test Load)	-	10000	Load Test
Clause No. 9.3 Annex C(Permanent set of cover)	-	10000	Load Test
Clause No. 9.3 Annex C(Cracks at bottom side of the cover )	-	10000	Load Test
Clause No. 9.3 Annex C(Adhesion between concrete and reinforcing steel)	-	10000	Load Test
Clause No. 5.2, Figure 1(Typical Illustration of circular precast concrete manhole cover)	-	7500	Dimension

18 Dec, 2027

-
-

IS 12894 (2002)

Pulverized fuel ash - Lime bricks - Specification

All

6500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
3.1(General Requirements)	-	500	General Requirements
3.2(General Requirements)	-	500	General Requirements
3.3(General Requirements)	-	500	General Requirements
3.4(General Requirements)	-	500	General Requirements
3.5(General Requirements)	-	500	General Requirements
5.1(Dimensions)	-	1000	All Dimensions
7.1, Table -1(Average Wet Compressive Strength)	-	2000	All Dimensions
7.2(Drying Shrinkage)	-	5000	Drying Shrinkage
7.3(Efflorescence Test)	-	1000	Efflorescence Test
7.4(Water Absorption)	-	2000	Water Absorption

18 Dec, 2027

-
-

IS 2645 (2003)

Integral waterproofing compounds for cement mortar and concrete - Specification (Second Revision)

13875 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	5000	Permeability
Cl 3.2(Initial & Final)	-	1000	Initial & Final Setting
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	3000	Compressive strength
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	5000	Permeability to water
Cl 3.2(Initial & Final)	-	1000	Initial & Final Setting
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	3000	Compressive strength
Cl 3.1(The permeability of water in specimen Prepared with WPC shall be less than half the permeability of plain cement specimens. (i.e ; < 50 percent))	-	5000	Permeability to water
Cl 3.2(Initial & Final)	-	1000	Initial & Final Setting
Cl 3.3(Compressive Strength, At 3days & 7 days)	-	3000	Compressive strength
Clause 3.4(Chloride content)	-	1000	Chloride content
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 3 days (72 ± 1 h))	-	3000	Testing Charges As per Parameter
Clause 3.3(Compressive strength of cement mortar at 3 days (72 ± 1 h))	-	3000	Testing Charges As per Parameter
Clause 3.2(Final setting time of cement)	-	3000	Testing Charges As per Parameter
Clause 3.1 (Permeability to water of cement mortar)	-	5000	Testing Charges As per Parameter
Clause 3.1 (Permeability to water of cement mortar with Water proofing compound)	-	5000	Testing Charges As per Parameter
Clause 3.2(Initial setting time of cement)	-	3000	Testing Charges As per Parameter
Clause 3.2(Initial setting time of cement with Water proofing compound)	-	3000	Testing Charges As per Parameter
Clause 3.2(Final setting time of cement with Water proofing compound)	-	3000	Testing Charges As per Parameter
Clause 3.3(Compressive strength of cement mortar at 7 days (168 ± 2 h))	-	3000	Testing Charges As per Parameter
Clause 3.3(Compressive strength of cement mortar with waterproofing compound at 7 days (168 ± 2 h))	-	3000	Testing Charges As per Parameter

18 Dec, 2027

-
-

IS 10748 (2004)

Hot - Rolled steel strip for welded tubes and pipes - Specification (Second Revision)

All

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8 & Table 3(UTM)	-	3000	Tensile
Cl 9(Press)	-	1500	Bend
Cl 11(Workmanship)	-	500	Freedom From Defects
Cl 12 & 13(Length, Width & Thickness)	-	500	Dimension
7.1(Carbon %)	-	500	Carbon
7.1(Manganese %)	-	500	Manganese
7.1(Phosphorus %)	-	500	Phosphorous
7.1(Sulphur %)	-	500	Sulphur
7.1(Silicon %)	-	500	Silicon
7.1( Copper %)	-	100	Copper
7.1( Aluminium %)	-	100	Aluminium
7.1( Nb)	-	100	Niobium
7.1(V)	-	100	Vanadium
7.1( Ti)	-	100	Titanium
7.1(Cr)	-	100	Chromium
7.1(Mo)	-	100	Molybdenum
7.1(Ni)	-	100	Nickle
7.1(CE)	-	300	Carbon Equivalent
7.1( Nitrogen%)	-	1500	Nitrogen
Cl. 8, Table 3(Yield Stress)	-	3000	Yield Stress
Cl. 8, Table 3(Elongation)	-	3000	Elongation
Cl. 14(Weight)	-	500	Weight
Cl. 12, 13(Camber)	-	500	Dimension

18 Dec, 2027

-
-

IS 2185 : Part 1 (2005)

Concrete masonry units - Specification: Part 1 hollow and solid concrete blocks (Third Revision)

All

20000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9.1(PHYSICAL REQUIREMENTS-General)	-	1000	General and Visual Inspection
9.2 & 4.2(PHYSICAL REQUIREMENTS-Nominal Dimensions 1.Length 2.Hight 3. Width)	-	1000	All Dimensions
9.2 & 4.2.3(Nominal Dimensions-variation in the length of units )	-	1000	All Dimensions
9.2 & 4.2.3(Nominal Dimensions -variation in height and width of units )	-	1000	All Dimensions
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the face shell)	-	1000	All Dimensions
9.2 & 4.2.4, Table-1(Nominal Dimensions-thickness of the Web shell)	-	1000	All Dimensions
9.3 & 5.1 & 5.2 Table 2(PHYSICAL REQUIREMENTS-Blocks Density - 1.Hollow (Open and Closed Cavity) Concrete Block- Grade Aor Grade B 2.Solid Concrete Block — Grade C)	-	1000	Blocks Density
9.4- Table 2(PHYSICAL REQUIREMENTS - Compressive Strength 1.Minimum Average Compressive Strength of Units 2.Minimum Average Compressive Strength of Individual Unit)	-	5000	Compressive Strength
9.5(PHYSICAL REQUIREMENTS -Water Absorption)	-	3000	Water Absorption
9.6(PHYSICAL REQUIREMENTS -Drying Shrinkage)	-	7500	Drying Shrinkage
9.7(PHYSICAL REQUIREMENTS -Moisture Movement)	-	3000	Moisture Movement
15(Marking)	-	1000	Marking

18 Dec, 2027

-
-

IS 280 (2006)

Mild steel wire for general engineering purposes (Fourth Revision)

All

8000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7 & Table 1(Diameter & Difference Between Two Reading On Any Two Diameters)	-	500	Dimension
Cl 9(Tensile Test On UTM)	-	2000	Tensile
Cl 13(Workmanship)	-	500	Freedom from defects
Cl 11(Workmanship)	-	2000	Zinc Coating
13(Freedom from defects)	-	500	Freedom from Defects
7 & 8(Diameter)	-	500	Dimension
7 & 8(Ovality)	-	500	Dimension
9.2(Wrapping Test)	-	2000	Wrapping Test
9.3(Bend test)	-	1500	Bend Test
Cl 11(Workmanship)	-	500	Workmanship (IS 7887 : 1992)

18 Dec, 2027

-
-

IS 3601 (2006)

Steel tubes for mechanical and general engineering purposes - Specification (Second Revision)

All

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(Material)	-	1000	Sulphur & Phosphorous
13(Mechanical Testing)	-	12000	Mechanical (Tensile, Bend, Flattening, Crushing, Drift Expansion)
6.0(Workmanship)	-	500	Freedom from Defects
4.1(Sulphur-Percentage by mass)	-	500	Sulphur
4.1(Phosphorus-Percentage by mass)	-	500	Phosphorous
8.0(Straightness)	-	500	Dimension
19.1.1, 24.1.1, 28.1.1, 33.1.1(Dimensions- Outside Dia)	-	500	Dimension
19.1.2, 24.1.2, 28.1.2, 33.1.2(Dimensions- Thickness)	-	500	Dimension
11.2(Surface Protection)	-	1000	Uniformity of Coating
13.1.3(Tensile Strength)	-	5000	Tensile
13.1.1(Yield Stress)	-	5000	Tensile
13.1.2(Elongation)	-	5000	Tensile
13.2(Flattening Test)	-	2000	Flattening
13.4(Bend Test (Whole Tube))	-	2000	Bend
13.5(Drift Expansion Test)	-	2000	Drift Expansion
13.6(Crush Test)	-	2000	Crushing
13.3(Bend Test (Strip))	-	2000	Bend
19.1.3(Height of Internal Fin)	-	500	Dimension
Cl. 10 Annex B Cl. 17, Cl. 19(Mass)	-	500	Mass
Cl. 9(Length)	-	500	Dimension
Cl. 10 Annex B Cl. 17, Cl. 19(Moment of inertia)	-	500	Dimension Geometric Properties
Cl. 10 Annex B Cl. 17, Cl. 19(Radius of gyration)	-	50	Dimension Geometric Properties
Cl. 10 Annex B Cl. 17, Cl. 19(Modulus of section)	-	500	Dimension Geometric Properties
Cl. 10 Annex B Cl. 17, Cl. 19(Area of cross section)	-	500	Dimension Geometric Properties

18 Dec, 2027

-
-

IS 15647 (2006)

Hot rolled steel narrow width strip for welded tubes and pipes

All

11000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(UTM)	-	3000	Tensile
Cl 9(Press)	-	1000	Bend
Cl 11(Workmanship)	-	500	Freedom From Defects
Cl 12(Length, Width & Thickness)	-	500	Dimesions
Cl 13(Workmanship)	-	500	Freedom from Defects
Cl. 12(Weight)	-	500	Weight
Cl. 12(Edge Camber)	-	500	Dimension
Cl. 12(Thickness)	-	500	Dimension
Cl. 8.2 Table 3(Elongation)	-	3000	Elonagtion
Cl. 8.2 Table 3(Yield Stress)	-	3000	Yield

18 Dec, 2027

-
-

IS 4457 (2007)

Ceramic unglazed vitreous acid resisting tiles - Specification (Second Revision)

All

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 5, Table 1 - iv -a (Resistance to Chemicals - Annex F)	-	10000	Resistance to Chemicals
Cl. 5, Table 1 - iv -b (Resistance to conc. HNO3 and conc. H2SO4 - Annex G)	-	10000	Resistance to conc. HNO3 and conc. H2SO4
4.1(DIMENSIONS AND TOLERANCES- Size)	-	10000	All Dimensions
4.2(DIMENSIONS AND TOLERANCES- Thickness)	-	10000	All Dimensions
5-Table 1(i)-a(REQUIREMENTS-Dimensions and Surface Quality-Length)	-	11000	All Dimensions and Surface Quality
5-Table 1(i)-a(REQUIREMENTS-Dimensions and Surface Quality-Width)	-	11000	All Dimensions and Surface Quality
5-Table 1(i)-b(REQUIREMENTS-Dimensions and Surface Quality-Thickness)	-	11000	All Dimensions and Surface Quality
5-Table 1(i)-c(REQUIREMENTS-Dimensions and Surface Quality-Straightness of sided)	-	11000	All Dimensions
5-Table 1(i)-d(REQUIREMENTS-Dimensions and Surface Quality-Rectangularity)	-	10000	All Dimensions
5-Table 1(i)-e(REQUIREMENTS-Dimensions and Surface Quality-Surface flatness-Centre curvature)	-	11000	All Dimensions and Surface Quality
5-Table 1(i)-e(REQUIREMENTS-Dimensions and Surface Quality-Surface flatness-Edge curvature)	-	11000	All Dimensions and Surface Quality
5-Table 1(i)-e(REQUIREMENTS-Dimensions and Surface Quality-Surface flatness-Warpage)	-	11000	All Dimensions and Surface Quality
5-Table 1(ii)(REQUIREMENTS-Surface Quality)	-	1000	Surface Quality
5-Table 1(iii)(REQUIREMENTS-Physical Properties-Water absorption by weigh(Average))	-	10000	Water Absorption
5-Table 1(iii)-a(REQUIREMENTS-Physical Properties-Water absorption by weigh(Indivisual))	-	10000	Water Absorption
5-Table 1(iii)-b-1(REQUIREMENTS-Physical Properties-Breaking strengrh(Thickness>=7.5mm))	-	15000	Modulus of Rupture and Breaking Strength
5-Table 1(iii)b-2(REQUIREMENTS-Physical Properties-Breaking strengrh(Thickness <7.5mm))	-	15000	Modulus of Rupture and Breaking Strength
5-Table 1(iii)-c(REQUIREMENTS-Physical Properties-Modulus of rupture(Average))	-	15000	Modulus of Rupture and Breaking Strength
5-Table 1(iii)-c(REQUIREMENTS-Physical Properties-Modulus of rupture(Individual))	-	15000	Modulus of Rupture and Breaking Strength
5-Table 1(iii)-d(REQUIREMENTS-Physical Properties-Abrusion resistance)	-	5000	Abrasion

18 Dec, 2027

-
-

IS 302 : Part 1 (2008)

Safety of household and similar electrical appliances: Part 1 general requirements (Sixth Revision)

52500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking and instructions)	-	1000	Testing charges parameter wise
8.1.1(Protection against live parts in all positions)	-	1000	Testing charges parameter wise
8.1.2(Protection against live parts in openings)	-	1000	Testing charges parameter wise
8.1.3(Protection against live parts in visible glowing heating elements)	-	1000	Testing charges parameter wise
8.1.4(Protection against live parts against protective impedance)	-	3000	Testing charges parameter wise
10.1(Power input)	-	3000	Testing charges parameter wise
10.2(Current input)	-	3000	Testing charges parameter wise
11.1(General)	-	1000	Testing charges parameter wise
11.2(General)	-	1000	Testing charges parameter wise
11.3(Heating)	-	6000	Testing charges parameter wise
13.1(General)	-	1000	Testing charges parameter wise
13.2(Leakage current at operating temperature)	-	5000	Testing charges parameter wise
13.3(Electric Strength at operating temperature)	-	6000	Testing charges parameter wise
14(Transient Over Voltages)	-	8000	Testing charges parameter wise
15.0(General)	-	1000	Testing charges parameter wise
15.1(Ingress Protection test other than IPX0 (IP test))	-	10000	Testing charges parameter wise
15.2(Spillage Test)	-	3000	Testing charges parameter wise
15.3(Humidity Test)	-	5000	Testing charges parameter wise
16.0(General)	-	1000	Testing charges parameter wise
16.1(General)	-	1000	Testing charges parameter wise
16.2(Leakage Current (after Clause 15))	-	5000	Testing charges parameter wise
16.3(Electric Strength (after clause 15 and 16.2))	-	6000	Testing charges parameter wise
17(Over Load Protection of Transformers and associated circuits)	-	6000	Testing charges parameter wise
18(Endurance Test requirements and tests)	-	1000	Testing charges parameter wise
19(Abnormal Operation)	-	8000	Testing charges parameter wise
20(Stability test)	-	2000	Testing charges parameter wise
21(Mechanical Strength Test)	-	5000	Testing charges parameter wise
22(Construction verification related test)	-	8000	Testing charges parameter wise
23(General)	-	2500	Testing charges parameter wise
24(Components)	-	2000	Testing charges parameter wise
25(Supply connection and external flexible cords)	-	7000	Testing charges parameter wise
26(Terminals for external conductors)	-	3000	Testing charges parameter wise
27(Provision for earthing)	-	3000	Testing charges parameter wise
28(Screw test and connections)	-	5000	Testing charges parameter wise
29(clearance, creepage distances and solid insulation)	-	9000	Testing charges parameter wise
30.1(Ball pressure test)	-	3000	Testing charges parameter wise
30.2(Glow Wire Test)	-	3000	Testing charges parameter wise
30.2(Needle Flame Test)	-	3000	Testing charges parameter wise
31(Resistance to Rusting)	-	2000	Testing charges parameter wise
32(Radiation Toxicity and Similar Hazards)	-	2000	Testing charges parameter wise

18 Dec, 2027

-
Exclusion 24 (Components) 19 (Abnormal Operation)

IS 6240 (2008)

Hot rolled steel plate (Up To 6 Mm) sheet and strip for the manufacture of low pressure liquefiable gas cylinders (Fourth Revision)

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(UTM)	-	3000	Tensile
Cl 8(Press)	-	1000	Bend
Cl 9(Strainage Embrittlement)	-	5000	Strainage Embrrittlement
Cl 10(Erichsen Cupping)	-	3000	Cupping
Cl 13(Length, Width & Thickness)	-	1000	Dimension
6.1(Carbon %)	-	500	Carbon
6.1(Manganese %)	-	500	Manganese
6.1(Phosphorus %)	-	500	Phosphorous
6.1(Sulphur %)	-	500	Sulphur
6.1(Silicon %)	-	500	Silicon
6.1( Aluminium %)	-	500	Aluminium
6.1(Nitrogen%)	-	1500	Nitrogen
Cl. 13(Out of square)	-	1000	Dimension
Cl. 13(Flatness)	-	1000	Dimension
Cl. 13(Camber)	-	1000	Dimension
Cl. 13(Width)	-	1000	Dimension
Cl. 13(Thickness)	-	1000	Dimension
Cl. 12(Freedom from defects)	-	1000	Freedom from Defect
Cl. 7.2 Table 3(Elongation)	-	3000	Elongation
Cl. 7.2 Table 3(Yield Stress)	-	3000	Elongation

18 Dec, 2027

-
-

IS 13488 (2008)

Irrigation equipment - Emitting pipe systems - Specification (First Revision)

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5.1.2 (Ref. Cl 4.1.b of IS 12786 : 1989)(Potyethylene - anti-oxidant)	-	1500	OK
5.1.2 (Ref. Cl 4.1.c.i of IS 12786 : 1989)(Density)	-	1000	OK
5.1.2 (Ref. Cl 4.1.c.ii of IS 12786 : 1989)(Toluene extract - Annex A of IS 12786:1989)	-	1500	OK
5.1.2 (Ref. Cl 4.1.c.iii of IS 12786 : 1989)(Volatile matter - Annex B of IS 12786:1989)	-	1000	OK
5.1.2 (Ref. Cl 4.1.c & 4.2.a of IS 12786 : 1989)(Carbon Black content - IS 2530 : 1963)	-	1500	OK
8.1.2(Uniformity of Emission Rate for Unregulated Emitting Pipes)	-	5000	OK
8.1.3(Uniformity of Emission Rate for Regulated Emitting Pipes)	-	5000	OK
8.2(Emission Rate of Emitting Unit as a Function of Inlet Pressure)	-	5000	OK
8.2.1(Unregu/Qt~d Emining Pipe)	-	5000	OK
8.2.2(Regulated Emitting Pipes)	-	5000	OK
8.3.1(Wall Thickness ofEmitting Pipe)	-	1000	OK
8.3.2(Inside Diameter ofEmitting Pipe)	-	1000	OK
8.3.3(Flow Paths in Emitting Unit)	-	1000	OK
8.3.4(Spacing ofEmitter Units)	-	1000	OK
8.4.1(Resistance to Hydrostatic Pressure at Ambient Temperature)	-	5000	OK
8.4.2(Resistance to Hydrostatic Pressure at Elevated Temperature)	-	5000	OK
8.5(Resistance to Tension at Elevated Temperature)	-	5000	OK
8.5(Resistance to Tension at Elevated Temperature)	-	5000	OK
8.5(Resistance to Tension at Elevated Temperature)	-	5000	OK
8.6(Resistance to Pull Out of Joints Between Fitting and Emitting IS 13479)	-	2000	OK
8.7.1(Resistance of PE Emitting Pipe to Environmental Stress Cracking -Acceptance Test Annex D of IS 12786)	-	5000	OK
8.7.2(Resistance of PE Emitting Pipe to Environmental Stress Cracking - Type Test Annex D of IS 12786)	-	5000	OK
8.8(Determination of Emitting Unit Exponent)	-	3000	OK

18 Dec, 2027

-
-

IS 15801 (2008)

Polypropylene - Random copolymer pipes for hot and cold water supplies - Specification

150000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(Dimensions Of Pipes)	-	3000	ok
Cl 8(Visual Appearance)	-	500	ok
Cl 9.1(Hydraulic Characteristics)	-	15000	ok
Cl 9.2(Fusion Compatibility)	-	2000	ok
Cl 9.3(Reversion Test )	-	5000	ok
Cl 9.4 & Annex B(Impact Strength)	-	5000	ok
Cl 9.5(Density)	-	1000	ok
Cl 9.6(Melt Flow Rate)	-	2000	ok
Cl 9.7(Carbon Black Content & Dispersion)	-	2000	ok
Cl 9.8(Thermal Stability By Hydrostatic Pressure Testing)	-	125000	ok
Cl 9.9(Opacity)	-	2000	ok

18 Dec, 2027

-
-

IS 278 (2009)

Galvanized steel barbed wire for fencing - Specification (Fourth Revision)

All

4500 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
5 Table-1(Sizes Diameter of Line wire)	-	1000	NA
5 Table-1(Sizes Diamater of Point wire)	-	1000	Dimension
5 Table-1(Sizes Mass of Completed barbed wire)	-	1000	Mass
5 Table-1(Sizes Distance between two barbs)	-	1000	Dimension
5 Table-1(Sizes No. of Lays between the two consequtive barbs)	-	1000	Dimension
9.1(Freedom from defects)	-	1000	Freedom from Defects
12.1(Tensile Strength)	-	1500	Tensile Test
12.1(Breaking load)	-	1500	Breaking Load
12.3(Ductility)	-	1500	Wrapping
12.2.1(Mass of zinc coating (line wire))	-	1500	Mass of Zinc Coating
12.2.2(Mass of zinc coating (point wire))	-	1500	Uniformity of Zinc Coating
Cl. 7.1(General)	-	1000	General
Cl. 7.2(Finishing of Barbs)	-	1000	Finishing of Barbs
Cl. 7.2(Length of Barbs)	-	1000	Dimension
Cl. 7.2(Cut Angle)	-	1000	Dimension
4(Type A/Type B)	-	1000	Type A/Type B

18 Dec, 2027

-
-

IS 3502 (2009)

Steel chequered plates (Third Revision)

All

11010 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 5(Workmanship)	-	1000	NA
Cl 8(Tensile Test)	-	7500	Tensile Test
Cl 9(Press)	-	1000	Bend Test
Cl 10(Length, Width, Thickness & Chequered Height)	-	1000	Dimenions
Cl. 11(Weight)	-	1000	Weight
Cl. 10(Thickness)	-	1000	Dimension
Cl. 10(Width)	-	1000	Dimension
Cl.8(Elongation)	-	7500	Elongation
Cl.8(Yield Stress)	-	7500	Yield Stress
Cl 10(Length, Width, Thickness & Chequered Height)	-	1000	Chequered Height

18 Dec, 2027

-
-

IS 13252 : Part 1 (2010)

Information technology equipment - Safety: Part 1 general requirements (Second Revision)

60000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1.5(Components)	-	1000	Testing charges parameter wise
1.6(Power interface .)	-	1000	Testing charges parameter wise
1.7(Markings and instructions)	-	1000	Testing charges parameter wise
2.1(Protection from electric shock and energy hazards)	-	5000	Testing charges parameter wise
2.2(SELV circuits)	-	3000	Testing charges parameter wise
2.3(TNV circuits)	-	5000	Testing charges parameter wise
2.4(Limited current circuits)	-	5000	Testing charges parameter wise
2.5(Limited power sources .)	-	5000	Testing charges parameter wise
2.6(Provisions for earthing and bonding)	-	3000	Testing charges parameter wise
2.7(Overcurrent and earth fault protection in primary circuits)	-	2000	Testing charges parameter wise
2.8(Safety interlocks)	-	2000	Testing charges parameter wise
2.9(Electrical insulation)	-	5000	Testing charges parameter wise
2.10(Clearances, creepage distances and distances through insulation)	-	10000	Testing charges parameter wise
3.1(General)	-	2000	Testing charges parameter wise
3.2(Connection to a mains supply)	-	6000	Testing charges parameter wise
3.3(Wiring terminals for connection of external conductors)	-	3000	Testing charges parameter wise
3.4(Disconnection from the mains supply)	-	1000	Testing charges parameter wise
3.5(Interconnection of equipment)	-	1000	Testing charges parameter wise
4.1(Stability)	-	2000	Testing charges parameter wise
4.2(Mechanical strength)	-	5000	Testing charges parameter wise
4.3(Design and construction)	-	3000	Testing charges parameter wise
4.4(Protection against hazardous moving parts)	-	2000	Testing charges parameter wise
4.5(Thermal requirements)	-	4000	Testing charges parameter wise
4.6(Openings in enclosures)	-	3000	Testing charges parameter wise
4.7(Resistance to fire)	-	5000	Testing charges parameter wise
5.1(Touch current and protective conductor curren)	-	3000	Testing charges parameter wise
5.2(Electric strength)	-	5000	Testing charges parameter wise
5.3(Abnormal operating and fault conditions)	-	6000	Testing charges parameter wise
6.1(Protection of telecommunication network service persons, and users of other equipment connected to the network, from hazards in the equipment)	-	2000	Testing charges parameter wise
6.2(Protection of equipment users from overvoltages on networks telecommunication)	-	5000	Testing charges parameter wise
6.3(Protection of the telecommunication wiring system from overheating)	-	5000	Testing charges parameter wise
7.1(General)	-	1000	Testing charges parameter wise
7.2(Protection of cable distribution system service persons, and users of other equipment connected to the system, from hazardous voltages in the equipment)	-	1000	Testing charges parameter wise
7.3(Protection of equipment users from overvoltages on the cable distribution system)	-	5000	Testing charges parameter wise
7.4(Insulation between primary circuits and cable distribution systems)	-	7000	Testing charges parameter wise

18 Dec, 2027

-
-

IS 15914 (2011)

High tensile strength flat rolled steel plate (Up To 6 Mm), sheet and strip for the manufacture of welded gas cylinder - Specification

All

12750 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7(UTM)	-	10000	NA
Cl 9(Workmanship)	-	1000	Freedom from Defects
Cl 10(Length, Width & Thickness)	-	1000	Dimensions
6.0(MICRO ALLOYING)	-	500	Micro Alloying
6.0(ALUMINIUM)	-	100	Aluminium
6.0(SILICON)	-	500	Silicon
6.0(MANGANESE)	-	500	Manganese
6.0(PHOSPHORUS)	-	500	Phosphorous
6.0(SULPHUR)	-	500	Sulphur
6.0(CARBON)	-	500	Carbon
6.0(NITROGEN)	-	2000	Nitrogen
Cl. 10(Mass)	-	1000	Weight
Cl. 10(Out of square)	-	1000	Dimension
Cl. 10(Flatness)	-	1000	Dimension
Cl. 10(Camber)	-	1000	Dimension
Cl. 10(Width)	-	1000	Dimension
Cl. 10(Thickness)	-	1000	Dimension
Cl. 7 Table 3(Elongation)	-	10000	Elongation
Cl. 7 Table 3(Yield Stress)	-	10000	Yield

18 Dec, 2027

-
-

IS 299 (2012)

Alumino - Ferric - Specification (Fifth Revision)

12000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
1 (i) Table 1( Insouble matter, Grade 4, A-3)	-	1500	-
1 (ii) Table 1(Soluble iron compound (as Fe2+ and Fe3+), Grade 4, A-4)	-	1500	-
1 (iii) Table 1(Water soluble aluminium compounds (as Al2O3), Grade 4, A-5)	-	1500	-
1 (iv) Table 1(pH (of 5 percent aqueous solution), Grade 4, A-6)	-	1000	-
1 (v) Table 1(Free acidity (as H2SO4)/Basicity (as Al2O3), Grade 4, A-7)	-	1500	-
1 (vi) Table 1( Lead (as Pb), Grade 4, A-8)	-	1500	-
1 (vii) Table 1(Arsenic (as As2O3), Grade 4, A-9)	-	1500	-
1 (viii) Table 1(Mercury (as Hg), Grade 4, A-10)	-	1500	-
1 (ix) Table 1(Manganese (as Mn), Grade 4, A-11)	-	1500	-
1 (x) Table 1(Chromium (as Cr), Grade 1, A-12)	-	1500	-
1 (xi) Table 1(Cadmium (as Cd), Grade 4, A-13)	-	1500	-
1 (xii) Table 1(Selenium (as Se), Grade 4, A-14)	-	1500	-
1 (xiii) (a) Table 1(Organic impurities:Phenolic compounds (as C6H5OH), Garde 4, A-15)	-	1500	-
1 (xiii) (b) Table 1(Anionic detergents (as MASS), Garde 1, A-16)	-	1500	-

18 Dec, 2027

-
-

IS 1237 (2012)

Cement Concrete Flooring Tiles - Specification

All

10000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	750	All Dimension
Cl 12.2(Concavity & Convexity )	-	750	All Dimension
Cl 12.3(The Maximum gap between the arms of the square and the edge of the title shall notexceed 2 percent of the length.)	-	750	All Dimension
Cl 12.4(Shall not exceed 1 percent of the length of the edge.)	-	750	All Dimension
Cl 12.5(Water absorption)	-	1000	Water absorption
Cl 12.6(Wet transverse strength )	-	2000	Wet transverse strength
Cl 12.7(Resistance to wear)	-	5000	Resistance to wear
Cl 11(Suface Finish)	-	500	Surface Finish
Cl 7.1(Length, Breadth, Minimum thickness, Difference in length of side between the longest side and shorterst side, Half tiles, Difference in Thickness between the thickest and thinnest tile, Thickness of wearing layer)	-	750	All Dimension

18 Dec, 2027

-
-

IS 2830 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into steel for general structural purposes - Specification (Third Revision)

All

8600 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 9(Workmanship)	-	500	NA
Cl 10.1(Workmanship)	-	500	Macro Examination
Cl 10.2(Workmanship)	-	500	Bend
Cl 10.3(Workmanship)	-	500	Camber
Cl 11(Length, Width & Thickness)	-	500	Dimension
6.1(Carbon %)	-	500	Carbon
6.1(Manganese %)	-	500	Manganese
6.1(Phosphorus %)	-	500	Phosphorous
6.1(Sulphur %)	-	500	Sulphur
6.1(Silicon %)	-	500	Silicon
6.1( Nitrogen%)	-	500	Nitrogen
6.1( Copper %)	-	100	Copper
6.1( Aluminium %)	-	100	Aluminium
6.1( Nb)	-	100	Niobium
6.1(V)	-	100	Vanadium
6.1( Ti)	-	100	Titanium
6.1(Cr)	-	100	Chromium
6.1(Mo)	-	100	Moybdenum
6.1(Ni)	-	100	Nickle
10.1 (a)(Macro-examination)	-	500	Macro Examination
Cl. 10.2(Bend)	-	500	Dimension
Cl. 10.3(Camber)	-	500	Dimension
11(Width)	-	500	Dimension
11(Thickness)	-	500	Dimension
Cl. 10.1 (b)(Sulphur Print)	-	8000	Sulphur Print
Cl. 11.2(Out of Squareness)	-	500	Dimension

18 Dec, 2027

-
-

IS 2831 (2012)

Carbon steel cast billet ingots, billets, blooms and slabs for re-rolling into structural steel (Ordinary Quality) - Specification (Fourth Revision)

All

10325 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
9( FREEDOM FROM DEFECTS)	-	500	NA
10.1.a)( Macro examination IS 11371)	-	500	Macro Examination
10.1.b)( Sulphur print tests IS 12037)	-	8000	Sulphur Print
11 & 12(DIMENSIONS and Tolerances)	-	500	Dimension
Cl. 6.1, Table 1(Carbon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Carbon
Cl. 6.1, Table 1(Manganese- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Manganese
Cl. 6.1, Table 1(Sulphur- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Sulphur
Cl. 6.1, Table 1(Phosphorus- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Phosphorous
Cl. 6.1, Table 1(Silicon- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Silicon
Cl. 6.1, Table 1(Aluminium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	Aluminium
Cl. 6.1, Table 1(Nitrogen- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	Nitrogen
Cl. 6.1, Table 1(Copper- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	Copper
Cl. 6.1, Table 1(Niobium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	Niobium
Cl. 6.1, Table 1(Vanadium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	Vanadium
Cl. 6.1, Table 1(Titanium- IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	100	Titanium

18 Dec, 2027

-
-

IS 10322 : Part 5 : Sec 1 (2012)

Luminaires: Part 5 particular requirements: Sec 1 fixed general purpose luminaires (First Revision)

21800 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
4(General Test Requireements)	-	1000	Testing Charges As per parameter
5(Classification of Luminaires')	-	1000	Testing Charges As per parameter
6.0(Marking)	-	3000	Testing Charges As per parameter
7.0(Construction)	-	10000	Testing Charges As per parameter
8.0(Creepage Distance and Clearances)	-	6000	Testing Charges As per parameter
9.0(Provision for earthing)	-	5000	Testing Charges As per parameter
10.0(Terminals)	-	9000	Testing Charges As per parameter
11.0(External & Internal Wiring)	-	6000	Testing Charges As per parameter
12.0(Protection against electric shock)	-	5000	Testing Charges As per parameter
13.0(Endurance Tests and Thermal Tests)	-	14000	Testing Charges As per parameter
14.0(Resistance to Dust & Moisture)	-	15000	Testing Charges As per parameter
15.0(Insulation Resistance and Electric Strength)	-	10000	Testing Charges As per parameter
16.0(Resistance to Heat , fire and tracking)	-	12000	Testing Charges As per parameter

18 Dec, 2027

-
-

IS 15885 : Part 2 : Sec 13 (2012)

Safety of lamp controlgear: Part 2 particular requirements: Sec 13 d.c. or a.c. supplied electronic controlgear for led modules

50000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
7(Marking)	-	1000	-
8(Protection against accidental contact with live parts)	-	5000	-
9(Terminals)	-	8000	-
10(PROVISION FOR EARTHING)	-	3000	-
11(MOISTURE RESISTANCE)	-	9000	-
12(Electric Strength)	-	5000	-
13(Thermal endurance test for winding of ballasts)	-	1000	-
14(Fault conditions)	-	8000	-
15(Transformer heating)	-	9000	-
16(Construction)	-	6000	-
17(Creepage distance and clearances)	-	5000	-
18(Screws, current carrying parts and connections)	-	5000	-
19(Resistance to heat, fire and tracking)	-	10000	-
20(Resistance to corrosion)	-	5000	-

18 Dec, 2027

-
-

IS 15961 (2012)

Hot dip aluminium - Zinc alloy metallic coated steel strip and sheet (Plain)

All

7485 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 8(UTM)	-	5000	NA
Cl 9 & Table 2(Workmanship)	-	2000	Mass of Zinc Coating
Cl 10(Coating Adhesion )	-	2000	Coating Adhesion
Cl 11(Workmanship)	-	500	Freedom From Defects
Cl 12(Weight)	-	500	Weight
Cl 13(Length, Width, Thickness, Camber, Deviation From Squareness & Deviation From Flatness)	-	1000	Dimension

18 Dec, 2027

-
-

IS 15962 (2012)

Structural steels for buildings and structures with improved seismic resistance

All

40000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl 6(Freedom from Defects)	-	2000	Freedom from Defects
Cl 10(Tensile Test)	-	25000	Tensile Test
Cl 11(Impact Test)	-	7500	Impact Test
Cl 13(Dimensions)	-	2000	Dimensions
Cl 16(Mass)	-	500	Mass
Clauses 7, 8.1 & .2, Table- 1(E250S, C)	-	100	Carbon
Clauses 7, 8.1 & .2, Table- 1(E250S, Mn )	-	100	Manganese
Clauses 7, 8.1 & .2, Table- 1(E250S, P)	-	100	Phosphorous
Clauses 7, 8.1 & .2, Table- 1(E250S, S)	-	100	Sulphur
Clauses 7, 8.1 & .2, Table- 1(E250S, Si)	-	100	Silicon
Clauses 7, 8.1 & .2, Table- 1(E250S, CE)	-	500	Carbon Equivalent
Clauses 7, 8.1 & .2, Table- 1(E300S, C)	-	100	Carbon
Clauses 7, 8.1 & .2, Table- 1(E300S, Mn)	-	100	Manganese
Clauses 7, 8.1 & .2, Table- 1(E300S, P)	-	100	Phosphorous
Clauses 7, 8.1 & .2, Table- 1(E300S, S)	-	100	Sulphur
Clauses 7, 8.1 & .2, Table- 1(E300S, Si)	-	100	Silicon
Clauses 7, 8.1 & .2, Table- 1(E300S, CE)	-	500	Carbon Equivalent
Clauses 7, 8.1 & .2, Table- 1(E350S, C)	-	100	Carbon
Clauses 7, 8.1 & .2, Table- 1(E350S, Mn)	-	100	Manganese
Clauses 7, 8.1 & .2, Table- 1(E350S, P)	-	100	Phosphorous
Clauses 7, 8.1 & .2, Table- 1(E350S, S)	-	100	Sulphur
Clauses 7, 8.1 & .2, Table- 1(E350S, Si)	-	100	Silicon
Clauses 7, 8.1 & .2, Table- 1(E450S, C)	-	100	Carbon
Clauses 7, 8.1 & .2, Table- 1(E450S, Mn)	-	100	Manganese
Clauses 7, 8.1 & .2, Table- 1(E450S, P)	-	100	Phosphorous
Clauses 7, 8.1 & .2, Table- 1(E450S, S)	-	100	Sulphur
Clauses 7, 8.1 & .2, Table- 1(E450S, Si)	-	100	Silicon
Clauses 7, 8.1 & .2, Table- 1(E450S, CE)	-	500	Carbon Equivalent
Clauses 7, 8.1 & .2, Table- 1(E350S, CE)	-	500	Carbon Equivalent

18 Dec, 2027

-
-

IS 15997 (2012)

Low nickel austenitic stainless steel sheet and strip for utensils and kitchen appliances - Specification

All

15000 View breakup
-

Clause No.	Exclusion	Testing Charges (Excl. Of Taxes)	Remark
Cl. 8.1, 8.1.1 & 10.1 Table 1(Carbon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Carbon
Cl. 8.1, 8.1.1 & 10.1 Table 1(Silicon -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Silicon
Cl. 8.1, 8.1.1 & 10.1 Table 1(Manganese -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Manganese
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nickel -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	Nickle
Cl. 8.1, 8.1.1 & 10.1 Table 1(Chromium -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	Chromium
Cl. 8.1, 8.1.1 & 10.1 Table 1(Sulphur -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Suphur
Cl. 8.1, 8.1.1 & 10.1 Table 1(Phosphorus -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	500	Phosphorous
Cl. 8.1, 8.1.1 & 10.1 Table 1(Copper -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	750	Copper
Cl. 8.1, 8.1.1 & 10.1 Table 1(Nitrogen -IS 228 and relevant parts or any other established Instrumental/Chemical method.)	-	1500	Nitrogen
6(Freedom From Defects)	-	500	Freedom from Defects
9.3(Tensile Test-1608:Part 1)	-	10000	Tensile Test
9.3, Table 3 (Yield Strength, Mpa)	-	10000	Tensile
9.3, Table 3 (Elongation, %)	-	10000	Tensile
9.4(Erichsen Cupping Test,(Average depth of cupping) mm)	-	2000	Cupping
12(Dimensions)	-	1000	Dimensions
14.1(Thickness,mm)	-	1000	Dimensions
14.2( Width, mm)	-	1000	Dimensions
14.3(Length, mm)	-	1000	Dimensions
14.4(Flatness, mm)	-	1000	Dimensions
14.5(Camber, mm)	-	1000	Dimensions

18 Dec, 2027

-
-

First
Prev
1
2
3
4
Next
Last

Bureau of Indian Standards

The National Standards Body of India

Kailtech Test and Research Centre Pvt. Ltd., Indore

141C, Electronic Complex Industrial Area, Indore, Indore, Madhya Pradesh, 452010

- contact@kailtech.net

Scope List